Escolar Documentos
Profissional Documentos
Cultura Documentos
Chassis
SK4.0L
CA
H_17210_000.eps 070607
Contents
Page
1. Technical Specifications, Connections, and Chassis Overview 2 2. Safety Instructions, Warnings, and Notes 4 3. Directions for Use 6 4. Mechanical Instructions 7 5. Service Modes, Error Codes, and Fault Finding 9 6. Block Diagrams, Test Point Overviews, and Waveforms Block Diagram Chassis 11 Schematic Overview Chassis 12 7. Circuit Diagrams and PWB Layouts Mono Carrier: Power Supply (A1) 13 Mono Carrier: Line Deflection (A2) 14 Mono Carrier: Frame Deflection (A3) 15 Mono Carrier: Tuner IF (A4) 16 Mono Carrier: AV Switch (A5) 17 Mono Carrier: Audio Amplifier (A6) 19 Mono Carrier: Tone Control (Optional) (A7) 18 Mono Carrier: CPU & Decoder (A8) 20 Keyboard Control Panel (D) 23 Main Switch Panel (E) 25 Side A/V Panel (G) 26 BTSC Panel (G) 27 Slim EW Panel (M) 28 Sub Woofer Panel (Optional) (Z) 29 8. Alignments 31 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets 36 Abbreviation List 37 IC Data Sheets 38 10. Spare Parts List 53 11. Revision List 56
Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.
Subject to modification
EN 2
1.
SK4.0L CA
1.2
Connection Overview
Note: The following connector colour abbreviations are used (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, and Ye= Yellow.
1.2.1
1.1
1.1.1
Technical Specifications
Vision Display type Screen size Tuning system TV Colour systems Video playback Presets/channels Tuner bands : : : : : : : : : CRT 21 (55 cm), 4:3 PLL NTSC, PAL M/N NTSC M/N 3.58, 4.43 PAL 50 181 channels VHF UHF
H_17210_023.eps 080607
Figure 1-1 Rear and Side Connections Cinch: Video CVBS - Out, Audio - Out Ye - Video CVBS 1 VPP / 75 ohm Wh - Audio L 0.5 VRMS /10 kohm Rd - Audio R 0.5 VRMS / 10 kohm Cinch: Video CVBS - In, Audio - In Ye - Video CVBS 1 VPP / 75 ohm Wh - Audio L 0.5 VRMS / 10 kohm Rd - Audio R 0.5 VRMS / 10 kohm Cinch: Video YPbPr - In Gn - Video Y 1 VPP / 75 ohm Bu - Video Pb 0.7 VPP / 75 ohm Rd - Video Pr 0.7 VPP / 75 ohm Aerial - In - - IEC-type (EU)
1.1.2
kq kq kq
1.1.3
Miscellaneous Power supply: - Mains voltage (VAC) - Mains frequency (Hz) Ambient conditions: - Temperature range (C) - Maximum humidity Power consumption - Normal operation (W) - Stand-by (W)
jq jq jq
: 90 - 260 : 50 / 60
jq jq jq
Coax, 75 ohm
: 72 : <3
Cinch: Video CVBS - In, Audio - In Ye - Video CVBS 1 VPP / 75 ohm Wh - Audio L 0.5 VRMS / 10 kohm Rd - Audio R 0.5 VRMS / 10 kohm
jq jq jq
Technical Specifications, Connections, and Chassis Overview 1.3 Chassis Overview (Mechanical chassis)
SK4.0L CA
1.
EN 3
A
Figure 1-2 PWB location
H_17450_003.eps 210907
EN 4
2.
SK4.0L CA
2.1
Safety Instructions
Safety regulations require the following during a repair: Connect the set to the Mains/AC Power via an isolation transformer (> 800 VA). Replace safety components, indicated by the symbol h, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Wear safety goggles when you replace the CRT. Safety regulations require that after a repair, the set must be returned in its original condition. Pay in particular attention to the following points: General repair instruction: as a strict precaution, we advise you to re-solder the solder connections through which the horizontal deflection current flows. In particular this is valid for the: 1. Pins of the line output transformer (LOT). 2. Fly-back capacitor(s). 3. S-correction capacitor(s). 4. Line output transistor. 5. Pins of the connector with wires to the deflection coil. 6. Other components through which the deflection current flows. Note: This re-soldering is advised to prevent bad connections due to metal fatigue in solder connections, and is therefore only necessary for television sets more than two years old. Route the wire trees and EHT cable correctly and secure them with the mounted cable clamps. Check the insulation of the Mains/AC Power lead for external damage. Check the strain relief of the Mains/AC Power cord for proper function, to prevent the cord from touching the CRT, hot components, or heat sinks. Check the electrical DC resistance between the Mains/AC Power plug and the secondary side (only for sets that have a Mains/AC Power isolated power supply): 1. Unplug the Mains/AC Power cord and connect a wire between the two pins of the Mains/AC Power plug. 2. Set the Mains/AC Power switch to the "on" position (keep the Mains/AC Power cord unplugged!). 3. Measure the resistance value between the pins of the Mains/AC Power plug and the metal shielding of the tuner or the aerial connection on the set. The reading should be between 4.5 Mohm and 12 Mohm. 4. Switch "off" the set, and remove the wire between the two pins of the Mains/AC Power plug. Check the cabinet for defects, to prevent touching of any inner parts by the customer.
2.3
Warnings
In order to prevent damage to ICs and transistors, avoid all high voltage flashovers. In order to prevent damage to the picture tube, use the method shown in figure Discharge picture tube, to discharge the picture tube. Use a high voltage probe and a multi-meter (position VDC). Discharge until the meter reading is 0 V (after approx. 30 s).
E_06532_007.eps 250304
Figure 2-1 Discharge picture tube All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD w). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this same potential. Available ESD protection equipment: Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. Wristband tester 4822 344 13999. Be careful during measurements in the high voltage section. Never replace modules or other components while the unit is switched "on". When you align the set, use plastic rather than metal tools. This will prevent any short circuits and prevents circuits from becoming unstable.
2.4
2.4.1
Notes
General Measure the voltages and waveforms with regard to the chassis (= tuner) ground (H), or hot ground (I), depending on the tested area of circuitry. The voltages and waveforms shown in the diagrams are indicative. Measure them in the Service Default Mode (see chapter 5) with a colour bar signal and stereo sound (L: 3 kHz, R: 1 kHz unless stated otherwise) and picture carrier at 475.25 MHz for PAL, or 61.25 MHz for NTSC (channel 3). Where necessary, measure the waveforms and voltages with (D) and without (E) aerial signal. Measure the voltages in the power supply section both in normal operation (G) and in stand-by (F). These values are indicated by means of the appropriate symbols. The semiconductors indicated in the circuit diagram and in the parts lists, are interchangeable per position with the semiconductors in the unit, irrespective of the type indication on these semiconductors. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol, are trademarks of Dolby Laboratories.
2.2
Maintenance Instructions
We recommend a maintenance inspection carried out by qualified service personnel. The interval depends on the usage conditions: When a customer uses the set under normal circumstances, for example in a living room, the recommended interval is three to five years. When a customer uses the set in an environment with higher dust, grease, or moisture levels, for example in a kitchen, the recommended interval is one year. The maintenance inspection includes the following actions:
SK4.0L CA
2.
EN 5
Practical Service Precautions It makes sense to avoid exposure to electrical shock. While some sources are expected to have a possible dangerous impact, others of quite high potential are of limited current and are sometimes held in less regard. Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected reactions that are best avoided. Before reaching into a powered TV set, it is best to test the high voltage insulation. It is easy to do, and is a good service precaution.
2.4.3
Lead-free Soldering Due to lead-free technology some rules have to be respected by the workshop during a repair: Use only lead-free soldering tin Philips SAC305 with order code 0622 149 00106. If lead-free solder paste is required, please contact the manufacturer of your soldering equipment. In general, use of solder paste within workshops should be avoided because paste is not easy to store and to handle. Use only adequate solder tools applicable for lead-free soldering tin. The solder tool must be able: To reach a solder-tip temperature of at least 400C. To stabilize the adjusted temperature at the solder-tip. To exchange solder-tips for different applications. Adjust your solder tool so that a temperature of around 360C - 380C is reached and stabilized at the solder joint. Heating time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400C, otherwise wear-out of tips will increase drastically and flux-fluid will be destroyed. To avoid wear-out of tips, switch off unused equipment or reduce heat. Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
2.4.4
Alternative BOM identification In September 2003, Philips CE introduced a change in the way the serial number (or production number, see Figure 2-2) is composed. From this date on, the third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative BOM (Bill of Materials used for producing the specific model of TV set). It is possible that the same TV model on the market is produced with e.g. two different types of displays, coming from two different O.E.M.s. By looking at the third digit of the serial number, the service technician can see if there is more than one type of B.O.M. used in the production of the TV set he is working with. He can then consult the At Your Service Web site, where he can type in the Commercial Type Version Number of the TV set (e.g. 28PW9515/12), after which a screen will appear that gives information about the number of alternative B.O.M.s used. If the third digit of the serial number contains the number 1 (example: AG1B033500001), then there is only one B.O.M. version of the TV set on the market. If the third digit is a 2 (example: AG2B0335000001), then there are two different B.O.M.s. Information about this is important for ordering the correct spare parts! For the third digit, the numbers 1...9 and the characters A...Z can be used, so in total: 9 plus 26 = 35 different B.O.M.s can be indicated by the third digit of the serial number.
EN 6
3.
SK4.0L CA
Mechanical Instructions
SK4.0L CA
4.
EN 7
4. Mechanical Instructions
Index of this chapter: 4.1 Set Disassembly 4.2 Assembly / Board Removal 4.3 Set Re-assembly Note: Figures below can deviate slightly from the actual situation, due to the different set executions.
4.2
4.2.1
4.1
Set Disassembly
Follow the disassemble instructions in described order.
4.1.1
Rear Cover Removal Warning: disconnect the mains power cord before you remove the rear cover. 1. Remove all the fixation screws of the rear cover. 2. Now, pull the rear cover backwards and remove it.
H_17210_025.eps 130607
Figure 4-2 Side-I/O panel removal 1. Disconnect the sidepanel cable from the mono carrier and remove the cable from its strain reliefs. 2. Then, remove the two fixation screws (1) and remove the board.
H_17210_032.eps 110607
EN 8
4.2.2
4.
SK4.0L CA
Mechanical Instructions
H_17210_026.eps 080607
Figure 4-3 Power switch removal 1. From the mono carrier disconnect the main power, the degaussing coil, the speakers, the front control panel, the side I/O panel and deflection coil cables. Release the main power cord and the side I/O panel cable from its strain reliefs. Pull out the mono carrier and place it sidewards. This enables the removal of the power switch panel. 2. Then, remove the two fixation screws (1) of the power switch panel and remove the board.
4.2.3
1
H_17210_027.eps 080607
Figure 4-4 Front Control Panel removal 1. From the mainboard disconnect the main power, the degaussing coil, the speakers, the front control panel, the side I/O panel and deflection coil cables. Release the main power cord and the side I/O panel cable from its strain reliefs. Pull out the mono carrier and place it sidewards. This enables the removal of the front control panel. 2. Then, remove the four fixation screws (1) of the Front Control panel and remove the board.
4.3
Set Re-assembly
To re-assemble the whole set, do all processes in reverse order. Be sure that, before the rear cover is mounted: The mains cord is positioned correctly in its guiding brackets (make sure that the strain reliefs are replaced in its correct position and that it will function correctly!). All wires/cables are returned in their original positions.
SK4.0L CA
5.
EN 9
5.1
Test Points
See chapter 6 "Block Diagrams, Testpoint Overviews, and Waveforms". Perform measurements under the following conditions: Service Default Mode. Video: colour bar signal. Audio: 3 kHz left, 1 kHz right.
5.4.7
Picture with Horizontal Bright Line and Sound Check both supply voltages of vertical IC301 and relevant circuitry on correctness. Also check the vertical synchronizing signal from IC201.
5.4.8
Remote Control Malfunction Check the voltage on pin 64 of IC201. The normal value should be 5.15 V. If this is correct check front control panels soldering connections. If can't be solved, check the remote control, crystal or transmitting diode of the remote control are in good condition.
5.2
Service Modes
This chassis does not contain a specific Service Mode. Service and Alignment of the TV set can be done via the Factory Mode by the service technician, see further down in this manual.
5.4.9
No Sound Check power supply of sound IC (IC402) and relevant circuitry. Check as well the BTSC board, check the power supply of IC801 and relevant output signal pins 21 and 27 of this IC. Do not exclude IC801 and/or IC402 to be defective. If needed replace the speakers.
5.3
Error Codes
Not applicable.
5.4
5.4.1
Fault Finding
Power on Failure Check whether the power supply is working properly and whether the values of voltages normal. If those are correct, check line transistor and transformer are working properly or check fore or back line for defects.
5.4.10 Poor Sound Quality Check the sound system after searching the channel which should set at NTSC or AUTO. If still has problem, check accompany board circuit on chassis good or not.
5.4.2
Horizontal Deflection Transistor Defective: No Picture, No Sound. To find the fault for a defect horizontal deflection transistor please check the following items: Over voltage to breakdown. Over current to burn. Horizontal frequency too low. Horizontal drive inefficient.
5.4.3
Picture Interference Check if the signal line contact is good. Change Tuner if is necessary.
5.4.4
Can't find any TV program Checking method: Check the closed circuit from tuner to picture decoder IC to detect whether there are defective components. Or check whether the resistance of R117, R118, R203 and R204 has increased which also could cause the problem.
5.4.5
No Good Picture or Double Image Check the correctness of the signal from IF1/IF2 to Q101 and relevant circuit. In this case the problem can be Q101 and/or SAW101.
EN 10
5.
SK4.0L CA
Personal Notes:
E_06532_012.eps 131004
SK4.0L CA
6.
EN 11
Y ANTENNA SCART 1 V in
AUDIO REAR AV V L R
G
SIDE AV V L R S-VHS Y C V AV OUT L R
D
A7
AV-SW 4052
13
L R
CVBS OUT
4 62 63 AV in FS TUNER
C in
FM
1 3 12 10 9 4 11
TONE CONTROL
15 2 5 14
A5
A6
AMP-TDA9841/9842/9843
SPL
SPR
C
A4
IF
IF AMP
SAW101
IF
SCL SDA
KEY CONTROL
SCL SDA
SDA
SCL
K
MTS/A2/NICAM R G B IK
D
PWM CONTROL AUDIO VOL MUTE AUDIO OUT SCART ID
21" CRT
CRT BOARD
A8
B
B
SDA SCL
V--DY
A3
POWER
E
90V-260V
SW
V AMP TDA4863AJ
24C08
H--DY
CQ0765
+12V
M
-12V
3DD5023
A1
A
SLIM PART
H DRIVE
A2
A
DEG COIL
H_17450_011.eps 210907
SK4.0L CA
6.
EN 12
H_17450_006.eps 210907
SK4.0L CA
7.
EN 13
A1
D
POWER SUPPLY
A1
D
Stand by
5800 A3P610-00
1 2 3 4
H_17450_009.eps 210907
SK4.0L CA
7.
EN 14
A2
D
LINE DEFLECTION
EHT BCL
A2
CN301
EHT
BCL
T0 CRT
1 GND
4 1 80 V
3 CRT G N D
2 HEATER
D309
R310 560K
+48V_VCC +8V_VCC
R301
!
T301
+V
0.33
D305 MTZJ20
T302
R302
2W
3 +V 4 -V 6 HEATER 7
R316
-V
0.33 R325
AFC
AFC
AFC
H-out
100
!
C321 2200pF C322 220pF C323
R403 NC
500V
500V
160V
1uF
+135V_VCC
B+
180V SCREEN
D205
C300
470PF 500 V
D308 R314 2158 0.22 2W L432 790mH L302 34mH R321 1K C319
SCREEN
1N4148
B
R323 75K Q302 D5032 Q303 F630
681
8 ABL
FLYBACK
+8V_VCC
!
C314 2n7 /2KV
R324
EW
100
!
R454 33
C315 7n2
!
C316 6n8
HY
D302 BY228 C317 564 D311 RU4B L301 105mH C318 274J/400V C325 364J/400
2KV
2KV
C312 273J/630V
50V
A A
5800 A3P610-00
1 2 3 4
H_17450_010.eps 210907
SK4.0L CA
7.
EN 15
A3
D
FRAME DEFLECTION
A3
CN301
IC301
!
I NN I NP
TDA4863AJ
Vp3 pump
VP1 +13V
VP4 -13V
V out
VP3-
!
100V
C307
C VDRA VDRB
R255 100 R256 100 C216 CAP C215 CAP R305 1K8
0.1uF/100V
270 1W
R308 1K8
+8V
R304 220/1W
2W
D302 BA158
C302
470pF
v+ B
B
D301
R326 10K
Q301
EHT R303
C302 0.1uF C301 0.1uF C304 1000uF/ 25V C303 1000uF/ 25V
C301
470pF
v-
5800 A3P610-00
1 2 3 4
H_17210_003.eps 110607
SK4.0L CA
7.
EN 16
A4
E
TUNER IF
Q102 C1815 10K LC101
A4
E
31.9M
A101
D
R106 R105 1.5K 68 C107
NTSC-M
R113
IF NC BT+33V GND
C703 47/50V
L101J
10n
C109 10n
R109 1.2K
C108 100pF
1UH
R108 4.7K
R111 470
220
SYSTEM
SYSTEM
C SYSTEM 1 SYSTEM1
C109 0.01U
L201 10UH
C104 100U/16V
R112 10
SIF SAW102
SIF SAW102
SAS NC B AGC
C103 10U/16V R215 680 R102 15K
+33V_BT
+8V_VCC
TUNER AGC SDA
38MHZ
38.9MHz
R101 27K
SCL
5800 A3P610-00
1 2 3 4 5
H_17210_004.eps 110607
SK4.0L CA
7.
EN 17
A5
D
AV SWITCH
Personal Notes:
A5
D
+8v
CVBS +8V
R251 1K R829 10 C823 10U/16V
CVBS
21
Q204
VI 20 VIG 18
17 19
D802
8V2 D807 75
VIDEO OUT
C1815
4 .7K R 84 0
R 8 41
4.7K
R842 4.7K
R802 75
Q803 1815
BL 16
15
AV1
AV1
BG 14
13
D834 8V2
NC 12
11
AV2
AV2
NC 10
9
D833 8V2
R836 75
OPT 8 L in 6
5 7
J743 10K
1 .5K R 85 5 1 .5K R 85 4 1 .5K R 85 2
R837 10K
AV3
GND 4 LO RO
P701
R731 820
L803
R835 75
D832 8V2
C
C717
R in2
1
21PIN
V / R in
C242
C
10uF
Y / G in U / B in
P701
U
R803 75
C IN
YUV
V
C IN
AUDIO L out
C804 10uF
AUDIO R out
C807 10uF
TONE 26 TONE 7
R847 100
V out R846 750
Q802
R844 100
Q801
C1815
R845 750
C1815
R848
R849
P701
AV OUT
L out
100K 100K
+8V
R out R824 100K C821 1U/ 50V 1U/ 50V
+8V
C777 V IN C190 R825 100K
C 8 17 CA P
+8V
C820
+8V
R830 100K
R831 2.7K
10uF C772
OUT L
10U/16V
P701
L IN
+8V
10uF C774 R IN R777 R780 100K R778 75 ZD706 8V2 ZD709 8V2 ZD711 8V2 R834 100K R827 100K
TONE 30
IC801 HEF4052
10uF
R821 100K
L 1 SIDE L +8V
R151 R152 100 300 10uF R826 100K
Vdd
16 15
+8V_VCC
+8V_VCC
SIDE AV IN
100K
2 0 3 4 5 1 2 3 3 0 1 2
SIDE R
C816 V IN
14 13 12 11 10 9
REAR R
4052 3
4052 13
4052 3 4052 13
L806
C811
REAR L
R828 100K R831 1.2K
TONE 32
P701
L IN
10uF C810
6 7
L805
R IN
R838 1K
A1 A2
A1 A2 A
+8V 8
R822 100K
R839 1K
REAR AV IN
R833 100K
R832 1.2K
5800 A3P610-00
1 2 3 4
H_17210_005.eps 070607
E_06532_012.eps 131004
SK4.0L CA
7.
EN 18
10
A6
A
TONE CONTROL
A6
A
WEIGHT TONE
B
R917 100K CN902 R914 510 C512 1000U C913 0.01U
C
R916 51K C910 0.22U C1815 Q902 R904 100K 820 R905 1K C914 0.22U 0.1U C908 R917 R909 100K R913 510 D901 8V2 C909 100U CAP C?
D
MUTE2 R
C901 10U C902 10U D903 4148 R901 10K R902 10K
D
VCC
IC901 TFA9800 C?
8 1 9
Q902 C907
4 6 2
WOODER 8OHM
R920 270
SVRR PG
F
C903 47U
R908 100K
5800 A3P610-00
H_17210_006.eps 110607
10
SK4.0L CA
7.
EN 19
A7
D
AUDIO AMPLIFIER
A7
D
+8V_VCC
+8V_VC C
2
D401 IN4148
4 3 5
L in
C428 47uF/ 50V
6 7
8 9
L out
IC402 TFA9842AJ
C
SPL C433 1000uF/ 25V
1
C432 100uF Q402 A1015 R410 75K
RI
RO
R411 47K
C429 220uF/25V
Lout
SW2
CN760
10W
1
MUTE
1 2
SW2 4 SPR 10W
MUTE
D761
R409 3K3
1N4148
Rout
VOL
VOL
R253 15K
B 4052 13 4050 3
R OUT L OUT
C749 1uF
1uF R769 1K
C426 106E
C424 222D
+22V_VCC
+22V_VCC
5800 A3P610-00
1 2 3 4
H_17210_007.eps 110607
SK4.0L CA
7.
EN 20
A8
A8
+5v
PT C
V dd
SCL
3 .3K R21 0
C202 100pF
C201 100pF
24C08
3 .3 K R208
3.3K R 20 2
IC202
3 .3K R20 5
47uF/ 16V
R2 07 3.3 k
3 .3K R20 3
0.01U
SD A
C227
C203
R235 3.3K
R220
R217 100
1 2 3 GN D 4 IR 5
LED K EY 5V
V ss
n .c.
WP
A2
+5V_VCC
+5V_VCC
5K1
1 2 3 4 5 6 7
C226 R218 10K 100U/ 10V C250 0.01U C205 D206 8V2 0.01U
STANDBY SCL SDA AV3/TUNING SCART ID KEY VOL MUTE Vss C/P LED PAL/NTSC VssA SECPLL Vp2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD VDRB VDRA IF1 IF2 IREF VSC TUNER AGC AUDEEM/SIF1 DECSDEM/SIF2 GND2 SNDPLL/SIFAGC AVL/REFO
IRin AV2 AV1 VddP RESET XTAL OUT XTAL IN OscGnd VddC VpE VddA B OUT G OUT R OUT BLANKING BCL IN B / U IN G / Y IN R / V IN BLANK AUDOUT/AMOUT C IN CVBS/Y IN GND1 CVBSINT Vp1 IFVO/SVO PLL IF EHTO AUDEXT/QSSO FBISO H. OUT
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
R231 2.2K C239 C240 C241 C230 X201 12MHz 33pF C229 33pF
A2 +3.3V A1
L202 10uH
+
C231 0.01U
L204 10uH
L203 10uH
VOL +3.3v C
VOL
+8V
C233 0.01u
+3.3V
8 9 10
C
C234 10u/16v R243 22K R725 R247 33K 10K R425 27K
R312
PAL NTSC
11 12
C207 0.22UF
3K3
ZD104 8V2
D203 8V2
D202 8V2
D204 8V2
1
2 3 4 5
13 14
10UH
220nF 2200p
15 16 17 18 19 20 21 22
GND B G CN102 R BL
BCL U / B in Y / G in V / R in BLANK
AUDIO OUT
C217 0.1U
EW VDRB VDRA IF
1 2
SAW101
SW02B
AGC SIF B
1 2
4 5
C221
3n3
Q9362M
NICAM NO NICAM
C223
A UD EXT
5800 A3P610-00
1 2 3 4
C IN CVBS/Y IN
4 5
R214 39K C213 0.1U/ 63V C219 0.022U
23 24 25 26 27 28 29
L205 C243 R229 390 C246 0.1U/ 63V 0.01U C244 100U/ 16V 10uH R220 100K R465
8V
+ C245
10U/16V
8v
EHT
EHT
30 31
C251 2.2U/ 50V
32
C220 4.7uF
C216 3.3K
AFC
R221 47
AFC H-out
H-out
Q201 C1815 L206 R224 100 R223 180 Z201 XT-6. 5 6.8uH
CVBS
CVBS
GND
Z202 XT-6. 0
GND
Q203 C1815 Z203 XT-5. 5 Q202
GND
C1815 Z204 XT-4. 5
R227 4K7
R226 4K7
GND
SYSTEM
SYSTEM 1
H_17210_008.eps 070607
SK4.0L CA
7.
EN 21
5800 A3P610-00
H_17210_009.eps 080607
SK4.0L CA
7.
EN 22
5800 A3P610-00
H_17210_010.eps 080607
SK4.0L CA
7.
EN 23
10
D
A
KEYBOARD CONTROL
D
A
KEYBOARD CIRCUIT
B B
KEYBOARD CIRCUIT
C
SW001 PROR717 RES R710 180 SW002 PRO+ R711 220 SW003 VOLR712 330 SW004 VOL+ R713 470 SW005 MENU R714 820 SW006 SLEEP SW007 MUTE R715 1.5K TV/AV R716 4.7K SW008 M001
3 2 1
C*** 10U
LED001
LED
1K
1 KEY 2 5V 3 GN D 4 IR 5
LED
5800 D1SL7P-61
H_17210_011.eps 080607
10
SK4.0L CA
7.
EN 24
5800 D1SL7P-61
Layout Keyboard Control Panel (Bottom Side)
H_17210_012.eps 080607
5800 D1SL7P-61
H_17210_013.eps 080607
SK4.0L CA
7.
EN 25
MAIN SWITCH
5800 E1SL7P-61
H_17210_015.eps 080607
5800 E1SL7P-61
H_17210_014.eps 080607
SK4.0L CA
7.
EN 26
SIDE AV
5800 G1SL7P-61
H_17210_016.eps 080607
BOTTOM SIDE
5800 G1SL7P-61
H_17210_017.eps 080607
SK4.0L CA
7.
EN 27
BTSC Panel
H_17450_001.eps 200907
H_17450_002.eps 200907
SK4.0L CA
7.
EN 28
Slim EW Panel
SLIM DEFLECTION
5800 M3P610-00
H_17210_019.eps 080607
5800 M3P610-00
H_17210_018.eps 080607
SK4.0L CA
7.
EN 29
SUB WOOFER
5800 Z3P610-00
H_17210_020.eps 080607
SK4.0L CA
7.
EN 30
Personal Notes:
5800 Z3P610-00
H_17210_021.eps 080607
E_06532_012.eps 131004
Alignments
SK4.0L CA
8.
EN 31
8. Alignments
Index of this chapter: 8.1 General Alignment Conditions 8.2 Hardware Alignments 8.3 Software Alignments 8.3.3 Screen Voltage Adjust (Key 0). 1. Set picture to Standard mode, without signal input. 2. Press the keys [i+], Smart sound and Smart picture to enter the factory menu. When in B/W BALANCE page, press mute on the RC. There will be a level light line displays. 3. Adjust flyback transformers Screen knob till the level bright line just can be seen, press PROG+ and turn to other factory menu. 4. When in the light-line screen, CUT R and CUT G can be adjusted if needed with the following RC key mapping: To increase /decrease CUT R (See table 8-1) To increase /decrease CUT G (See table 8-2) 5. Press MUTE key to return to the B/W BALANCE page. Table 8-1 To increase /decrease CUT R Function RC key CUT R+ 1 CUT R4
8.1
8.1.1
Table 8-2 To increase /decrease CUT G Function RC key 8.3.4 CUT G+ 2 CUT G5
8.2
Hardware Alignments
Note: The only hardware alignment in this TV set is the adjustment of the main voltage (B+), see below.
Horizontal Adjustment (key 1) 1. Provide a 50 Hz monoscope pattern. Press the keys [i+], Smart sound and Smart picture to enter the factory menu. Press the keys [i+] again and ADJUST appear on screen. 2. Press key 0 and adjust HPH to set picture horizontal centre to CRT horizontal centre.
8.2.1
Main Voltage Adjustment In order to adjust the main voltage, connect a voltage meter to the cathode of diode D610, and adjust VR601 to a voltage of 110 V 0.3 V.
8.3
Software Alignments
Put the set in its MENU mode (factory mode) as follows (see also figure Factory Mode on the next page): Press the keys [i+], smart sound and smart picture to enter the factory menu. Press the keys [i+] again and ADJUST appear on screen. Press the number keys to enter the adjust page, press B/ y to choose the items that to be adjusted, Press z/A to adjust its value. Press [i+] to quit factory mode. The different alignment parameters are described further on.
8.3.5
Vertical & YUV/RGB Horizontal Adjust (key2) 1. Provide a 50 Hz cross hatch signal, set TV to standard mode. Adjust VSL so that half picture of the pane cross appears. The pictures vertical line is just at the bottom of the half picture. Adjust VSL to make the centre of the pictures vertical line and the kinescope are in superposition. 2. Adjust VSI to obtain pictures vertical re-display ratio more than 90%. 3. Provide a 60 Hz cross hatch signal, do step 1 and 2 again to adjust. 4. If necessary, fine adjust above items.
8.3.1
Rf AGC Voltage Adjust 1. Provide a 294.25 MHz, 60 dB half colour bar signal. 2. Enter factory mode and press key 1. 3. Measure tuner AGC point voltage, adjust AGC item till the voltage is 2.4 V, or till picture noise just disappears. (typical value is at 27).
8.3.6
OSD Position (Key 4) 1. Menu OSD position adjustment: Provide a 50/60 Hz cross hatch pattern. Put the set in MENU mode. Press the keys [i+], Smart sound and Smart picture to enter the factory menu. Press the keys [i+] again and ADJUST appear on screen. 2. LOGO position adjustment: Provide a 50/60 Hz cross hatch pattern. Put the set in MENU mode. Press key 7 to enter the factory mode. Adjust XMIN, XMAX, YMIN and YMAX, to obtain LOGO at the centre up to 1/3 of CRT screen. 3. Press key 4 to enter the factory mode. Adjust VP and HP item, to obtain menu OSD at the centre of CRT screen. 4. Provide a RGB or YUV cross hatch signal, set the TV in the standard mode, adjust YUV OSD HS 5RGH till picture horizontal centre is at the CRT centre (optional).
8.3.2
Focus Fine Adjust 1. Provide a cross-hatch pattern signal. 2. Set state to Rich mode. 3. Adjust flyback transformers Focus knob till picture is clear.
EN 32
8.
SK4.0L CA
Alignments
Main Page B/W BALANCE DRI R DRI G DRI B CUT R CUT G BT CT COOL DR COOL DG COOL DB COOL CR COOL CG WARM DR WARM DG WARM DB WARM CR WARM CG 32 26 28 32 31 32 32 -2 -1 +2 +1 +0 +10 +7 -1 +0 -1
SERVICE 0 FREQUENCY H PH V SL V SH V SI V SC EW WIDTH EW PARA UP CORNER LO CORNER H -PARA H-BOW EW TRAPE ZOOM 60HZ 36-TV 35 23 26 19 54 46 29 28 15 43 23 44 SERVICE 1 SHIPMODE AGC AGC SPEED IF HRC&IRC MULTI SYSTEM PWL XDT XDT COUNT MVS MAT BPB CORING OSO > 27 1 45.75M 0FF OFF 8 1 30 USA OFF 1 3 ON SERVICE 2 UOC VOL SW UOC/PWL VOL MONO GAIN STEREO GAIN SAP GAIN AV GAIN 9859 INPUT VOL 10 VOL 25 VOL 50 VPL 80 VOL 100 FMWS AVL OPT OFF 40 50 50 49 50 1 45 55 80 90 100 0 OFF
"I+"
ADJUST SERVICE 3 AV OPT AV CFG 2 AV YC/DVD VIDEO OUT PIN 5 PIN 7 PIN 8 MUTEPIN MODE CC HP CC LINE CC DELAY HCO OSVE
"0"
SERVICE 4 VP HP YUV OSD HS OSD L HALFTONE SYBER-SKY2-070810
"1"
SERVICE 5 BTSC-MODE BTSC-ST BTSC-SP BTSC-LI BTSC-A1 BTSC-A2 BTSC-TC BTSC-STS BTSC-ADJ MTS DETECT MTS FILTER W:00 00 40 09 0E 86 R: EE E6 D: MONO ST SAP
"2"
48 40 40 0 ON
STEREO 0 0 9 14 6 3 ON Start 50 20 03
"3"
"4"
"5"
SERVICE 6 POW POWER ON TIM AKB NBL WATCHDOG PHILIPS RC VCHIP GAME CALENDAR ZOOM OPT BLUE BACK BB WIDTH BLACK BACK STB
SERVICE 7 SUB BRI SUB CON SUB COL SUB SHA SUB TI YDL PAL YDL NTSC YDL AV CATHE MAX BRI MID BRI MAX CON MID CON SC. BRI
3 2 30 32 12 2 2 0 2 63 28 63 28 8
SERVICE 8 YUV DR YUV DG YUV DB YUV CR YUV CG ENGLISH SPAISH FRANCH PORTUGUESE
+0 -3 +0 +0 +0 ON ON OFF ON
"6"
"7"
"8"
"Smart Picture"
SOFT BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP VOICE BASS TREBLE SURROUND
"Smart Sound"
50 57 45 69 50 WARM
30 50 OFF
"Smart Picture"
RICH BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP MISIC BASS TREBLE SURROUND
"Smart Sound"
55 90 50 100 50 COOL 55 60 OFF
"Smart Picture"
NATURAL BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP THEATRE BASS TREBLE SURROUND
"Smart Sound"
50 75 50 80 50 NORMAL 80 70 ON
"Smart Picture"
"Smart Sound"
H_17450_008.eps 210907
SK4.0L CA
8.
EN 33
Range (Index value) 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 60 Hz 0-TV-63-TV 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 50 Hz 0-TV-63-TV 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 +5-AV +5-AV +0-YUV +0-YUV OFF 0-63 0-63 58.75 Mhz OFF 0-15 0-2 0-255 USA OFF 0-2 0-3 OFF OFF 0-63 0-63 ON ON JAP ON 45.75 Mhz ON ON ON
Default 32 32 32 32 32 32 32 -2 0 10 0 0 10 0 0 0 0
SK4.0L CA 32 32 32 32 32 32 32 -2 0 10 0 0 10 0 0 0 0
0x00d 0x00e 0x00f 0x010 0x011 0x02f 0x030 0x017 0x018 0x019
COOL offset according to CUT R value of tv, black level off-set R of COOL 0x01a COOL offset according to CUT G value of tv, black level off-set R of COOL 0x01b WARM offset according to DRI R value of tv, white point R of COOL Warm offset according to DRI G value of tv, white point G of COOL Warm offset according to DRI B value of tv, white point B of COOL 0x01c 0x01d 0x01e
Warm offset according to CUT R value of tv, black level off-set R of COOL 0x01f Warm offset according to CUT G value of tv, black level off-set R of COOL 0x020 Direct key 0 50hz/60hz Horizontal center Vertical slope Vertical center Vertical amplitude. Vertical s-correction. EW WIDTH EW parabola/width EW upper/lower corner parabola Bottom curve Horizontal parallelogram Horizontal bow EW trapezium Expand 4:3 mode horizontal WIDTH adjust 50hz/60hz Horizontal center Vertical slope Vertical center Vertical amplitude. Vertical s-correction. EW WIDTH EW parabola/width EW upper/lower corner parabola Bottom curve Horizontal parallelogram Horizontal bow EW trapezium Expand 4:3 mode horizontal WIDTH adjust Horizontal center in AV source. Horizontal center in AV source. Horizontal center in YUV source. Horizontal center in YUV source. Direct key 1 Out of box setting, Smart Picture: Rich, Contrast +: On, NR: Off, Smart Sound: Theatre, Tuner Mode: Auto, Volume: 30, CC: Off RF.AGC adjust AGC speed IF choose HRC and IRC of N system for auto search selection ON: PAL M/N ON, OFF: PAL M/N OFF White apex limit X ray protect X ray protection detect count NTSC decode matrix PAL, NTSC decode matrix Bypass of sound bandpass filter Video dependent coring Switch-off in vertical overscan Direct key 2 UOC control volume switch UOC/PWM modify volume value Volume of 9859 modify value when sound is mono
31-TV 24 21 33 27 32 32 32 32 32 32 32 44 31-TV 24 21 33 27 32 32 32 32 32 32 32 44 32 32 32 32
35-TV 30 22 22 19 51 45 33 33 35 35 30 44 35-TV 31 23 22 21 49 45 33 33 35 35 30 44 33 33 33 33
EN 34
8.
SK4.0L CA
Alignments
Storage address Display string 0x053 0x054 0x055 0x0e0 (bit3, bit2) 0x026 0x027 0x028 0x029 0x02a 0x0de (bit1, bit0) 0x0e8 (bit6) 0x0e1 (bit7, bit6) 0x0cc (bit7-bit4) 0x0ea (bit5) 0x0e9 (bit4) 0x0e7 (bit4) 0x0cc (bit3-bit0) 0x0cd (bit7-bit4) 0x0cd (bit3-bit0) 0x0e9 (bit0) 0x0ee (bit6) 0x05a 0x060 0x0d1 (bit3-bit0) 0x02b 0x02c 0x05b 0x0df (bit7, bit6) 0x0e9 (bit1) STEREO GAIN SAP GAIN AV GAIN 9859INPUT VOL 10 VOL 25 VOL 50 VOL 80 VOL 100 FMWS AVL OPT AV OPT AV CFG 2 AV YC/DVD VIDEO OUT PIN 5 PIN 7 PIN 8 MUTEPIN MODE MUTEPIN SEL CC HP CC LINE CC DELAY VP HP YUV OSD HS OSD L HALFTONE SOFTWARE VERSION NUMBER BTSC-MODE 0x0ce (bit7-bit4) 0x0ce(bit3-bit0) 0x040 0x041 0x042 0x0cf (bit7-bit4) 0x0e8 (bit3) 0x0e8 (bit2) 0x001 0x072 0x074 0x0dd (bit3, bit2) 0x0cb (bit3-bit0) 0x0e8 (bit0) 0x0e9 (bit7) 0x0eb (bit7) 0x0eb (bit6) 0x0ea (bit7) 0x0eb (bit5) 0x0eb (bit4) 0x0ec (bit6) 0x0e9 (bit6) 0x06d 0x0e1 (bit1, bit0) 0x0ee (bit7) 0x057 0x059 0x023 0x024 0x025 0x075 0x0c9 (bit3-bit0) 0x0c9 (bit7-bit4) BTSC-ST BTSC-SP BTSC-LI BTSC-A1 BTSC-A2 BTSC-TC BTSC-STS BTSC-ADJ MTS DETECT MTS FILTER MTS FILTER2 POW 0-15 0-60 8-23 0-63 0-63 0-60 0-3 OFF ON OFF ON Range (Index value) 0-63 0-63 0-63 0-2 0-100 0-100 0-100 0-100 0-100 0-2 OFF 0-3 0-7 OFF OFF IF ON ON CVBS ON Default 48 48 48 2 25 50 75 90 100 0 OFF 1 3 OFF OFF CVBS NTSC VOL1 MTUE OFF OFF 13 21 20 52 54 38 0 ON 13 21 12 52 50 38 2 ON SK4.0L CA 52 48 50 1 45 55 75 85 100 1 OFF 0 4 OFF OFF CVBS NTSC VOL1 LED
Description of the factory menu Volume of 9859 modify value when sound is stereo Volume of 9859 modify value when sound is SAP Volume of 9859 modify value when system is AV state 9859 control pin output state 10% volume point 25% volume point 50% volume point 80% volume point 100% volume point FM demodulate frequency width AVL function switch Direct key 3 AV control logic choose AV choose AV2 choose DVD choose Video output Pin 5 choose function Pin 7 choose function Pin 8 choose function MUTE pin mode OFF: Pin 7 control volume curve ON: Pin 4 control volume curve CCD Horizontal width adjust CCD scan Horizontal row when PAL N system CCD delay adjustment Direct key 4 OSD up down position OSD left right position RGB/YUV OSD Horizontal Center OSD output contrast Menu translucence Software version number
Direct key 5 Sound mode Stereo noise limit SAP noise limit Sound input level adjustment Separate Separate Time constant Stereo level switch Stereo adjustment on/off MTS detect time delay STEREO and SAP detect count MONO detect count Direct key 6 POWER ON MODE POWER ON time delay Black current stabilization Black current loop detect WATCH DOG ON: Philips RC OFF: Skyworth RC VCHIP FUNCTION SWITCH GAME FUNCTION SWITCH CALENDER FUNCTION SWITCH 4:3 expand function choose ON: Blue Screen OFF: Black Screen EW WIDTH offset according to EW WIDTH value when TV is no signal Video mute during change to program RGB BLANKING Direct key 7 Sub contrast Sub brightness Sub color Sub Sharpness TV Sub tint AV Sub tint PAL Luminance delay NTSC Luminance delay SUB BRI SUB CON SUB COL SUB SHA SUB TIN SUB TIN-AV YDL PAL YDL NTSC 0-63 0-63 0-63 0-63 0-31 0-31 0-15 0-15 0 0 30 32 16 16 2 2 4 3 30 32 16 16 2 2 MONO 0-15 0-15 0-15 0-31 0-31 0-7 OFF BUSY 0-255 0-255 0-255 ON START STEREO SAP 0 0 7 23 22 4 OFF START 50 20 20 2 12 ON ON ON ON ON ON ON ON ON ON ON OFF ON OFF OFF OFF ON ON +0 0 ON ON 0 0 9 14 6 3 ON START 50 20 3 2 8 ON ON OFF ON OFF OFF OFF OFF ON 0 0 ON
0-2 POWER ON TIM 2-17 AKB OFF NBL WATCHDOG PHILIPS RC VCHIP GAME CALENDER ZOOM OPT BLUE BLACK BB WIDTH BLACK BACK OFF OFF OFF OFF OFF OFF OFF OFF 53-10 0-2
Alignments
Description of the factory menu AV Luminance delay Maximum brightness Middle brightness Maximum contrast Middle contrast Line-level of brightness Direct key 8 YUV offset according to DRI R value of TV, white point R of YUV. YUV offset according to DRI G value of TV, white point G of YUV YUV offset according to DRI B value of TV, white point B of YUV YUV offset according to CUT R value of TV, black level offset R of YUV YUV offset according to CUT G value of TV, black level offset G of YUV English OSD switch Spanish OSD switch French OSD switch Portuguese OSD switch External Y (Luminance) input gain during YPRPB. OFF: gain 0 dB reduced, ON: gain 3 dB reduced Cathode drive level EHT tracking mode Black current measuring lines in overscan Manual INIT E2PROM INITEEP Key Smart sound BASS set value in Voice state TREBLE set value in Voice state SURROUND set value in Voice state BASS set value in Music state TREBLE set value in Music state SURROUND set value in Music state BASS set value in Theatre state TREBLE set value in Theatre state SURROUND set value in Theatre state Key Smart image Bright set value in Soft state Contrast set value in Soft state Color set value in Soft state Sharpness set value in Soft state Sharpness set value in Soft state of YUV COLOR TEMP set value in Soft state Bright set value in Rich state Contrast set value in Rich state Color set value in Rich state Sharpness set value in Rich state Sharpness set value in Rich state of YUV COLOR TEMP set value in Rich state Bright set value in Natural state Contrast set value in Natural state Color set value in Natural state Sharpness set value in Natural state Sharpness set value in Natural state of YUV COLOR TEMP set value in Natural state 0x064 0x065 0x066 0x067 0x068 0x069 0x06a 0x06b 0x06c 0x036 0x037 0x038 0x039 0x070 0x03a 0x03b 0x03c 0x03d 0x03e 0x071 0x03f 0x031 0x032 0x033 0x034 0x06f 0x035 BASS TREBLE SURROUND BASS TREBLE SURROUND BASS TREBLE SURROUND BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP BRIGHT CONTRAST COLOR SHARP YUV SHARP COLOR TEMP Storage address Display string 0x0ca(bit7-bit4) 0x056 0x021 0x058 0x022 0x02d 0x012 0x013 0x014 0x015 0x016 0x0eb (bit3) 0x0eb (bit2) 0x0eb (bit1) 0x0eb (bit0) 0x0ee (bit4) 0x0ca (bit3-bit0) 0x0ea (bit6) 0x0e9 (bit2) YDL AV MAX BRI MID BRI MAX CON MID CON SC.BRI YUV DR YUV DG YUV DB YUV CR YUV CG ENGLISH SPANISH FRANCE PORTUGUESE YGN CATHE HCO OSVE
SK4.0L CA
Range (Index value) 0-15 0-63 0-63 0-63 0-63 0-63 (-32) - (+31) (-32) - (+31) (-32) - (+31) (-32) - (+31) (-32) - (+31) OFF OFF OFF OFF OFF ON ON ON ON ON
8.
Default 4 63 18 63 15 8 +0 +0 +0 +0 +0 ON ON OFF ON OFF 3 ON OFF
EN 35
SK4.0L CA 2 63 18 63 15 8 +0 +0 +0 +0 +0 ON ON OFF ON ON 3 ON OFF
EN 36
9.
SK4.0L CA
9.1
Introduction
The SK4.0A CA is a CRT TV for the year 2007, based on the 3P61 platform. In this chapter, only a general description of the various circuits is given. For more detailed information, see the circuit diagrams in this manual.
9.2
9.2.1
9.2.2
IF Channel The IF Channel mainly ensures the sensitivity and selectivity of the complete TV set. The IF AMP integrated in the UOCIII is made up of a three-stage dual-differential amplifier with a gain value above 70dB, a SNR of 55dB and a bandwidth of 7 MHz. The video demodulation circuit is made from the built-in PLL Sync Detector. The spectrum of the demodulation carrier is unitary and it is not affected by the content of the video signal. The tuner features stable receptivity while the signal output from the video detector features high fidelity. The built-in PLL circuit of the UOCIII generates a 38.0 MHz or 38.9 MHz demodulation reference signal for the sync detector to demodulate the video signal; this is called PLL sync demodulation.
9.2.3
Sound Channel An external ceramic filter is used to select the second SIF signal for the sound channel of UOCIII from the signal output of the video detector. The audio signal is obtained after limiting amplification and demodulation by the intermediate frequency detector for the SIF signal, and then the audio signal is fed to the BTSC stereo/SAP decoder TDA9850. From that it is output to the audio amplifier TFA9842, which drives the speakers to provide the sound. The intermediate frequency detector and volume-control attenuator that are built in the UOCIII are set and adjusted via the CPU.
9.2.4
BTSC stereo/SAP decoder Input Level Adjustment The composite input signal is fed to the input level adjustment stage. The control range is from -3.5 to +4.0 dB in steps of 0.5 dB. The maximum input signal voltage is 2 V (RMS). Stereo Decoder The output signal of the level adjustment stage is coupled to a low-pass filter which suppresses the baseband noise above 125 kHz. The composite signal is then fed into a pilot detector/ pilot cancellation circuit and into the MPX demodulator. The main L + R signal passes a 75 ms fixed de-emphasis filter and is fed into the dematrix circuit. The decoded sub-signal L - R is sent to the stereo/SAP switch. To generate the pilot signal the stereo demodulator uses a PLL circuit including a ceramic
Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3 Abbreviation List
2CS A2 AC ACI 2 Carrier Sound Commonly known as 2 Carrier Sound (2CS) system Alternating Current Automatic Channel Installation: algorithm that installs TV channels directly from a cable network by means of a predefined TXT page Analogue to Digital Converter Automatic Frequency Control: control signal used to tune to the correct frequency Automatic Gain Control: algorithm that controls the video input of the feature box Amplitude Modulation Automatic Noise Reduction; One of the algorithms of Auto TV Asia Pacific Aspect Ratio: 4 by 3 or 16 by 9 Audio Video Automatic Volume Level control Monochrome TV system. Sound carrier distance is 5.5 MHz Beam Current Limiter Circuit Board Assembly (or PWB) Carbon Film Resistor Computer aided rePair Cathode Ray Tube (or picture tube) Composite Video Blanking and Synchronisation Component Video Input Monochrome TV system. Sound carrier distance is 6.5 MHz. D= VHFband, K= UHF-band Digital to Analogue Converter Direct Current Filament supply voltage Directions For Use: owner's manual Dolby Pro Logic Dynamic RAM; dynamically refreshed RAM Digital Versatile Disc Electrically Erasable and Programmable Read Only Memory Extreme High Tension; the voltage between the cathode and the shadow mask that accelerates the electrons towards the screen (around 25 kV) Electro Magnetic Interference; Leakage of high-frequency radiation from a transmission medium EUrope East West, related to horizontal deflection of the set East -West correction drive signal. EXTernal (source), entering the set by SCART or by cinches (jacks) Fast Blanking: DC signal accompanying RGB signals Front End; Tuner and RF part together Each interlaced broadcast FRAME is composed of two Fields, each Field consists of either Odd or Even lines Filament of CRT Field Memory / Frequency Modulation A complete TV picture comprising all lines (625/525) Flat TeleVision Green H_sync to the module Horizontal Drive H-FLYBACK H-OUT HA HFB HW I
SK4.0L CA
9.
EN 37
ADC AFC
AGC
I2 C I2 S IC IF IIC Interlaced
AM ANC AP AR AV AVL B/G BCL CBA CFR ComPair CRT CVBS CVI D/K
IO IR L L/L
LS M/N
NC NICAM
NTC
NTSC
EMI
NVM
PCB PLL
Horizontal Flyback H_sync output of the module / Horizontal Output pulse Horizontal Acquisition; horizontal sync pulse Horizontal Flyback Pulse; Horizontal sync pulse from large signal deflection Hardware Monochrome TV system. Sound carrier distance is 6.0 MHz. VHF- and UHF-band Inter IC bus (also called IIC) Inter IC Sound bus Integrated Circuit Intermediate Frequency Inter IC bus (also called I2C) Scan mode where two fields are used to form one frame. Each field contains half the number of the total amount of lines. The fields are written in pairs, causing line flicker. In/Out Infra Red Left audio channel Monochrome TV system. Sound carrier distance is 6.5 MHz. L' is Band I, L is all bands except for Band I LATin AMerica Light Emitting Diode Line Output Transformer (also called FBT); The transformer in which the EHT is generated Loud Speaker Monochrome TV system. Sound carrier distance is 4.5 MHz. M= 525 lines @ 60 Hz, N= 625 lines @ 50 Hz Metal Oxide Film Resistor Metal Oxide Semiconductor Field Effect Transistor MultiPleX North American Free Trade Association: Trade agreement between Canada, USA and Mexico Not Connected Near Instantaneously Companded Audio Multiplexing; This is a digital sound system, mainly used in Europe Negative Temperature Coefficient, non-linear resistor (resistance decreases if temperature increases) National Television Standard Committee. Colour system used mainly in North America and Japan. Colour carrier NTSC M/N = 3.579545 MHz, NTSC 4.43 = 4.433619 MHz (this is a VCR norm, it is not transmitted off-air) Non Volatile Memory; IC containing data such as alignment values, preset stations Option Byte Open Circuit OPtion byte On Screen Display Project 50; Communication protocol between TV and peripherals Phase Alternating Line; Colour system mainly used in West Europe (colour carrier= 4.433619 MHz) and South America (colour carrier PAL M= 3.575612 MHz and PAL N= 3.582056 MHz) Printed Circuit Board (or PWB) Phase Locked Loop; Used for e.g. FST tuning systems. The customer
EN 38
9.
SK4.0L CA
Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.4 IC Data Sheets
This section shows the internal block diagrams and pin layouts of ICs that are drawn as black boxes in the electrical diagrams.
Progressive Scan
PTC
SAW SC S/C SCL SD SDA SDRAM SIF SMC SMD SMPS SND SRAM STBY SVHS TBD TXT
can directly provide the desired frequency Scan mode where all scan lines are displayed in one frame at the same time, creating a double vertical resolution. Positive Temperature Coefficient, non linear resistor (resistance increases if temperature increases) Printed Wiring Board (also called PCB or CBA) Quasi Split Sound Right audio channel / Red Random Access Memory Remote Control transmitter Remote Control system 5 (6), the signal from the remote control receiver Real Flat (picture tube) or Radio Frequency Red, Green, and Blue colour space; The primary colour signals for TV. By mixing levels of R, G, and B, all colours (Y/C) are reproduced Red, Green, Blue, Horizontal sync, and Vertical sync Root Mean Square value Read Only Memory Secondary Audio Program; Generally used to transmit audio in a second language Surface Acoustic Wave SandCastle: two-level pulse derived from sync signals Short Circuit Serial Clock signal on I2C bus Standard Definition Serial Data line of I2C bus Synchronous DRAM Sound Intermediate Frequency Surface Mounted Component Surface Mounted Device Switched Mode Power Supply SouND Static RAM STandBY Super Video Home System To Be Defined Teletext; TXT is a digital addition to analogue TV signals that contain textual and graphical information (25 rows x 40 columns). The information is transmitted within the first 25 lines during the Vertical Blank Interval (VBI) Microcontroller Ultimate One Chip Microprocessor Colour difference signals V_sync Main supply for deflection (usually 141 V) Vertical Acquisition Vertical Blanking Interval; Time during which the video signal is blanked when going from bottom to top of the display Video Cassette Recorder Video Graphics Array Video Intermediate Frequency Write Enable control line World System Teletext Quartz crystal Luminance signal
SK4.0L CA
9.
EN 39
H_17210_039.eps 120607
EN 40
9.4.2
9.
SK4.0L CA
H_17210_039.eps 120607
SK4.0L CA
9.
EN 41
Block Diagram
THERMAL PROTECTION
TDA4865AJ
VERTICAL OUTPUT
FLYBACK GENERATOR
REFERENCE CIRCUIT
7 INP
6 INN
5 VOUT
RS1 CS1
4 GND
3 VP2
CF
2 VP3
1 VP1
D1 deflection coil C1 R1 C2 R5
RP R3
R6
R2
VN
VP
Pin Configuration
VP1 VP3 VP2 GND VOUT INN INP 1 2 3 4 5 6 7
TDA4865AJ
EN 42
9.
SK4.0L CA
H_17210_035.eps 120607
SK4.0L CA
9.
EN 43
Block Diagram
Pin Configuration
H_17210_041.eps 120607
EN 44
9.4.5
9.
SK4.0L CA
Block Diagram
VCC 9 IN1 4
60 k
OUT1
IN2
1
60 k
OUT2
CIV
3
VREF
VC
TFA9842AJ
SVR
5 GND
Pin Conguration
IN2 OUT2 CIV IN1 GND SVR VC OUT1 VCC 1 2 3 4 5 6 7 8 9
H_17210_033.eps 110607
TFA9842AJ
SK4.0L CA
9.
EN 45
Block Diagram
+ + +
C2 R1
13
14
STEREO DECODER
11
C1
SAP DEMODULATOR
5
+
C16
Pin Configuration
C3
C4
C5
Q1
ceramic resonator
C6
C7
15
16
17 L+R
18
L R/SAP
21
TDA9850
C8
MAD
26
+
1 R2
2
+
32
+
31
+
30
+
29
+
25
+
20
10
+
12
6
+
24
C15
C17
C19
C14 R3 C13
CL
CR
VCC
VCAP
Vref
1 2 3 4 5 6 7 8
TDA9850
9 VCC 10 COMP 11 VCAP 12 CP1 13 CP2 14 CPH 15 CADJ 16
EN 46
9.4.7
9.
SK4.0L CA
Block Diagram
H_17210_034.eps 130607
SK4.0L CA
9.
EN 47
Pin Configuration
H_17210_029.eps 130607
EN 48
9.
SK4.0L CA
H_17210_030.eps 130607
SK4.0L CA
9.
EN 49
Pinning
H_17210_031.eps 130607
EN 50
9.4.8
9.
SK4.0L CA
Block Diagram
QSSO/AMOUT/AUDEXT AUDOUT/AMOUT I/O PORTS (4x) LED OUT (2x)
TUNERAGC IFVO/SVO VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP. REF VIDEO SWITCH CVBS/Y C VIDEO IDENT. VIDEO FILTERS
VPE
SCL SDA
VST OUT
RESET
SIFIN
SOUND TRAP
ADC IN (4x)
+3.3 V
IFIN
MEMORY
COR
B BL RO GO BO BCLIN BLKIN
Y U V
HOUT
V-DRIVE
EHTO
EWD
Pin Configuration
P1.3/T1
handbook, halfpage
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
64 63 62 61 60 59 58 57 56 55 54
P1.2/INT0 P1.1/T0 P1.0/INT1 VDDP RESET XTALOUT XTALIN OSCGND VDDC VPE VDDA BO GO RO BLKIN BCLIN B2/U/PBIN G2/YIN R2/V/PRIN INSSW2 AUDOUT C CVBS/Y GND1 CVBS1 VP1 IFVO/SVO PLLIF EHTO AUDEXT/QSSO FBISO HOUT
P1.6/SCL P1.7/SDA P2.0/TPWM P3.0/ADC0/PWM0 P3.1/ADC1/PWM1 P3.2/ADC2/PWM2 P3.3/ADC3/PWM3 VSSC/P P0.5 P0.6 VSSA I.C. VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD/ DECSDEM VDRB VDRA IFIN1 IFIN2 IREF VSC AGCOUT AUDEEM/SIFIN1 DECSDEM/SIFIN2 GND2 SNDPLL/SIFAGC AVL/SNDIF/REFO/ AUDEEM
53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
XXX
H_17450_012.eps 210907
SK4.0L CA
9.
EN 51
H_17210_035.eps 120607
EN 52
9.
SK4.0L CA
Pin Configuration
H_17210_036.eps 120607
SK4.0L CA
10.
EN 53
f
R101 R102 R103 R105 R106 R107 R109 R111 R113 R117 R118 R150 R201 R202 R203 R204 R205 R206 R208 R210 R214 R215 R216 R217 R218 R219 R220 R221 R222 R223 R224 R228 R229 R230 R231 R232 R234 R235 R236 R237 R238 R239 R240 R241 R242 R243 R245 R246 R247 R250 R251 R252 R255 R256 R257 R258 R259 R260 R261 R301 R302 R304 R305 R306 R307 R307A R307B R308 R309 R310 R311 R312 R314 R315 R316 R317 R318 R321 R322 R323 R324 R325 9965 100 04841 9965 000 40686 9965 000 40130 9965 000 39984 9965 000 39983 9965 100 04838 9965 000 40304 9965 100 04849 9965 100 04838 9965 000 39975 9965 000 39975 9965 000 39975 9965 000 39975 9965 000 40695 9965 000 40695 9965 000 39975 9965 000 40695 9965 000 39975 9965 000 40686 9965 000 40700 9965 000 40122 9965 100 04849 9965 000 40695 9965 000 39975 9965 000 39976 9965 000 39975 9965 000 40695 9965 100 04846 9965 100 04839 9965 100 04838 9965 000 40694 9965 000 40304 9965 000 40687 9965 100 04836 9965 100 04839 9965 000 39984 9965 000 40695 9965 100 04839 9965 000 39975 9965 000 39975 9965 000 40706 9965 000 39975 9965 000 39975 9965 000 39975 9965 000 39976 9965 100 04841 9965 000 40304 9965 000 40686 9965 000 40698 9965 100 04848 9965 000 40304 9965 100 04841 9965 000 40700 9965 000 40700 9965 000 39975 9965 000 39975 9965 000 39984 9965 000 39975 9965 000 39975 9965 100 04864 9965 100 04864 9965 100 04856 9965 000 40687 9965 000 39985 9965 100 05312 9965 000 40524 9965 100 07705 9965 000 40687 9965 100 05314 9965 000 40702 9965 100 04841 9965 000 40304 9965 000 40145 9965 100 07892 9965 000 40141 9965 100 04838 9965 100 04842 9965 100 04859 9965 100 05313 9965 000 40701 9965 000 39975 9965 000 40691 27k 5% 1/16-1/6W CFR 15k 1/16W MOFR 27 CFR 75 1/16W CFR 56 1/16W 180 5% 1/16-1/6W CFR 1K 1/16W 680 5% 1/16-1/6W 180 5% 1/16-1/6W CFR 100 1/16W CFR 100 1/16W CFR 100 1/16W CFR 100 1/16W CFR 3.3k 1/16W CFR 3.3k 1/16W CFR 100 1/16W CFR 3.3k 1/16W CFR 100 1/16W CFR 15k 1/16W CFR 4.7k 1/16W MOFR 39k 680 5% 1/16-1/6W CFR 3.3k 1/16W CFR 100 1/16W CFR 10k 1/16W CFR 100 1/16W CFR 3.3k 1/16W 47 5% 1/16-1/6W 2.2k 5% 1/6W 180 5% 1/16-1/6W CFR 33 1/16W CFR 1K 1/16W CFR 1.8k 1/16W 1.2k 5% 1/16-1/6W 2.2k 5% 1/6W CFR 75 1/16W CFR 3.3k 1/16W 2.2k 5% 1/6W CFR 100 1/16W CFR 100 1/16W CFR 6.8k 1/16W CFR 100 1/16W CFR 100 1/16W CFR 100 1/16W CFR 10k 1/16W 27k 5% 1/16-1/6W CFR 1K 1/16W CFR 15k 1/16W CFR 39k 1/16W 5.6k 5% 1/16-1/6W CFR 1K 1/16W 27k 5% 1/16-1/6W CFR 4.7k 1/16W CFR 4.7k 1/16W CFR 100 1/16W CFR 100 1/16W CFR 75 1/16W CFR 100 1/16W CFR 100 1/16W 0.33 5% 2W 0.33 5% 2W 220 5% 1W CFR 1.8k 1/16W CFR 5.6 0.82 2W NTC 5/5A MOFR CFR 1.8k 1/16W 330 2W CFR 470k 1/16W 27k 5% 1/16-1/6W CFR 1K 1/16W Fusible 0.18 2W Fuse Resistor 3.3 2W MOFR 3.3k 180 5% 1/16-1/6W 330 5% 1/16-1/6W 1k 5% 2W 1.5 5% 2W CFR 47k 1/16W CFR 100 1/16W CFR 220 1/16W
g
C101 C102 C103 C104 C105 C106 C107 C110 C201 C202 C203 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C226 C227 C229 C230 C231 C232 C233 C234 C235 C236 C237 C238 C239 C240 C241 C243 C244 C245 C246 C247 C248 C253 C300 C301 C302 C303 C304 C305 C306 C307 C308 C309 9965 000 41097 9965 000 41097 9965 000 40171 9965 000 40172 9965 000 40156 9965 100 04885 9965 000 40156 9965 000 40156 9965 000 41097 9965 000 41097 9965 000 40156 9965 000 40171 9965 100 04892 9965 100 04870 9965 100 04867 9965 100 04892 9965 000 40178 9965 000 40156 9965 100 06012 9965 100 04866 9965 100 04866 9965 100 04866 9965 100 04891 9965 000 40180 9965 000 40156 9965 000 40171 9965 100 07709 9965 000 40171 9965 000 40208 9965 100 04873 9965 000 41097 9965 000 40176 9965 000 40529 9965 000 40529 9965 000 40172 9965 000 40156 9965 000 40156 9965 000 40171 9965 000 40156 9965 000 40171 9965 100 04871 9965 000 40179 9965 100 04868 9965 100 04868 9965 100 04868 9965 000 40172 9965 000 40156 9965 000 40171 9965 100 05386 9965 000 40158 9965 000 40175 9965 000 40180 9965 100 04874 9965 100 04874 9965 100 04874 9965 100 06011 9965 100 06011 9965 100 07710 9965 100 04891 9965 100 04891 9965 100 04891 9965 100 05317 100pF 50V 100pF 50V 10F 20% 16V 100F 20% 16V 0.01F 50V 0.47uF 20% 50V 0.01F 50V 0.01F 50V 100pF 50V 100pF 50V 0.01F 50V 10F 20% 16V 0.22F 5% 63-100V 0.0047F +80-20% 50V 0.0022F +80-20% 50V 0.22F 5% 63-100V 1F 20% 50V 0.01F 50V Met. Polyester Filmcap. 0.001uF 5% 50V 0.001uF 5% 50V 0.001uF 5% 50V 0.1F 5% 63-100V 2.2F20% 50V 0.01F 50V 10F 20% 16V 180pF 50V 10F 20% 16V Mylar 0.0015F 100V 390pF 10% 500V 100pF 50V 470F 20% 16V 33pF 50V 33pF 50V 100F 20% 16V 0.01F 50V 0.01F 50V 10F 20% 16V 0.01F 50V 10F 20% 16V 560pF 5% 50V 10F 20% 50V-63V 0.022F +80-20% 50V 0.022F +80-20% 50V 0.022F +80-20% 50V 100F 20% 16V 0.01F 50V 10F 20% 16V 0.01F 5% 100V 220pF 50V 47F 20% 16V 2.2F20% 50V 470pF 10% 500V 470pF 10% 500V 470pF 10% 500V EC.1000uF 25V +/-20% EC.1000uF 25V +/-20% 220F 0.1F 5% 63-100V 0.1F 5% 63-100V 0.1F 5% 63-100V 47F 20% 250V
EN 54
R326 R327 R401 R402 R405 R406 R407 R408 R409 R410 R411 R501 R502 R503 R504 R505 R506 R507 R508 R510 R511 R512 R513 R514 R515 R516 R517 R519 R520 R521 R522 R523 R524 R525 R526 R527 R601 R602 R603 R604 R605 R606 R607 R608 R609 R611 R612 R613 R614 R615 R616 R617 R618 R619 R621 R622 R623 R624 R625 R626 R630 R632 R633 R637 R638 R639 R640 R640 R801 R802 R804 R805 R806 R807 R817 R818 R835 R836 R841 R842 R843 R844 R847 R852 R854 RST601 RT602 VR601
10.
9965 000 39977 9965 100 04854 9965 000 40686 9965 000 40686 9965 000 40304 9965 000 40304 9965 000 39976 9965 000 40700 9965 000 40695 9965 100 04837 9965 000 39976 9965 000 40690 9965 100 04839 9965 000 40491 9965 000 40690 9965 100 04858 9965 000 40517 9965 100 04856 9965 100 04853 9965 000 39998 9965 000 40000 9965 000 39998 9965 000 40491 9965 100 04858 9965 000 40517 9965 100 04856 9965 100 04853 9965 000 40503 9965 100 04839 9965 000 39998 9965 000 39998 9965 000 40491 9965 100 04858 9965 000 40517 9965 100 04856 9965 100 04853 9965 000 40150 9965 100 04857 9965 000 40524 9965 000 40698 9965 000 40691 9965 000 40706 9965 000 39998 9965 100 04839 9965 000 40154 9965 100 04849 9965 100 04839 9965 000 40304 9965 100 04845 9965 000 40490 9965 100 04862 9965 100 04863 9965 100 04863 9965 100 04858 9965 100 04855 9965 100 04851 9965 000 40101 9965 000 39976 9965 000 39976 9965 000 39976 9965 000 39999 9965 000 39976 9965 000 40304 9965 000 40517 9965 000 39984 9965 000 39976 9965 100 04937 9965 100 06020 9965 000 40705 9965 100 04838 9965 100 05140 9965 100 05140 9965 000 39975 9965 000 39975 9965 100 05140 9965 100 05140 9965 000 39976 9965 000 39976 9965 000 40700 9965 000 40700 9965 000 40252 9965 000 39975 9965 000 39975 9965 000 40685 9965 000 40685 9965 100 04856 9965 100 04865 9965 000 40155
SK4.0L CA
CFR 100k 1.5k 5% 1W CFR 15k 1/16W CFR 15k 1/16W CFR 1K 1/16W CFR 1K 1/16W CFR 10k 1/16W CFR 4.7k 1/16W CFR 3.3k 1/16W 130k 5% 1/16-1/6W CFR 10k 1/16W CFR 22 1/16W 2.2k 5% 1/6W CFR 270 1W CFR 22 1/16W 270 5% 1W MOFR 15k 220 5% 1W 1k 5% 1W CFR 22 1/4W CFR 2.2k CFR 22 1/4W CFR 270 1W 270 5% 1W MOFR 15k 220 5% 1W 1k 5% 1W CFR 220k 1W 2.2k 5% 1/6W CFR 22 1/4W CFR 22 1/4W CFR 270 1W 270 5% 1W MOFR 15k 220 5% 1W 1k 5% 1W High Volt. 2.2M 1/2W 220k 5% 1W NTC 5/5A CFR 39k 1/16W CFR 220 1/16W CFR 6.8k 1/16W CFR 22 1/4W 2.2k 5% 1/6W High Volt. 8.2M 1W 680 5% 1/16-1/6W 2.2k 5% 1/6W CFR 1K 1/16W 4.3k 5% 1/16-1/6W CFR 220k 1W 0.22 5% 1W 0.33 5% 1W 0.33 5% 1W 270 5% 1W 22 5% 1W 820 5% 1/16-1/6W CFR 3.3k CFR 10k 1/16W CFR 10k 1/16W CFR 10k 1/16W CFR 220 CFR 10k 1/16W CFR 1K 1/16W MOFR 15k CFR 75 1/16W CFR 10k 1/16W Bead 3.5 X 1 X 5mm Bead 3.5 X 1 X 5mm CFR 68 1/16W 180 5% 1/16-1/6W 2.4k 5% 1/16-1/6W 2.4k 5% 1/16-1/6W CFR 100 1/16W CFR 100 1/16W 2.4k 5% 1/16-1/6W 2.4k 5% 1/16-1/6W CFR 10k 1/16W CFR 10k 1/16W CFR 4.7k 1/16W CFR 4.7k 1/16W Peaking coil 10H 10% CFR 100 1/16W CFR 100 1/16W CFR 1.5k 1/16W CFR 1.5k 1/16W 220 5% 1W Ther Resistor 9 for 29" Semi-fixed R 1KB (H)
d
D101 D201 D202 D203 D204 D205 D206 D207 D301A D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D401 D402 D501 D502 D503 D504 D505 D506 D603 D604 D605 D606 D607 D608 D609 D610 D611 D612 D613 D615 D616 D617 D801 D802 D803 D804 D805 9965 000 40221 9965 000 40221 9965 000 40224 9965 000 40224 9965 000 40224 9965 000 40218 9965 000 41175 9965 000 40221 9965 000 40224 9965 000 40219 9965 000 40219 9965 000 40219 9965 000 40218 9965 000 40224 9965 000 40218 9965 000 40219 9965 100 04909 9965 000 40219 9965 100 04906 9965 100 04904 9965 000 40218 9965 000 40218 9965 000 40218 9965 000 40219 9965 000 40218 9965 000 40219 9965 000 40218 9965 000 40219 9965 000 40219 9965 100 04909 9965 100 04911 9965 100 04911 9965 100 04911 9965 100 04911 9965 100 04907 9965 100 07483 9965 100 04906 9965 000 40219 9965 100 04905 9965 000 40219 9965 000 40220 9965 000 40218 9965 000 40224 9965 000 40224 9965 000 40224 9965 000 40224 9965 000 40224 Zener 5V1 1/2W 5% Zener 5V1 1/2W 5% Zener 8V2 1/2W 5% Zener 8V2 1/2W 5% Zener 8V2 1/2W 5% 1N4148 150mA/100V 6V2 5% 1/2W Zener 5V1 1/2W 5% Zener 8V2 1/2W 5% BA158 600V/1A BA158 600V/1A BA158 600V/1A 1N4148 150mA/100V Zener 8V2 1/2W 5% 1N4148 150mA/100V BA158 600V/1A Zener Diode 18V 1/2W BA158 600V/1A 3A/800V(DO-27) BY228 1N4148 150mA/100V 1N4148 150mA/100V 1N4148 150mA/100V BA158 600V/1A 1N4148 150mA/100V BA158 600V/1A 1N4148 150mA/100V BA158 600V/1A BA158 600V/1A Zener Diode 18V 1/2W TA20-08 2A/800V TA20-08 2A/800V TA20-08 2A/800V TA20-08 2A/800V 3V6 1/2W +/-5% High Speed Rect. RU4 3A/800V(DO-27) BA158 600V/1A TRU3YX 200V/2A BA158 600V/1A Zener 3V9 1/2W 5% 1N4148 150mA/100V Zener 8V2 1/2W 5% Zener 8V2 1/2W 5% Zener 8V2 1/2W 5% Zener 8V2 1/2W 5% Zener 8V2 1/2W 5%
g
CR1 9965 100 04879 10F 20% 10V
f
RD2 RD3 RD4 RD5 M001 9965 000 40693 9965 000 39975 9965 000 40688 9965 000 39976 9965 000 40270 CFR 2.7k 1/16W CFR 100 1/16W CFR 18k 1/16W CFR 10k 1/16W IR receiver mod. 36kHz
g
C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C821 C822 C823 C824 C825 C826 C827 C828 C829 9965 100 05388 9965 100 07708 9965 000 41112 9965 100 07706 9965 000 40171 9965 000 41112 9965 000 41112 9965 000 40561 9965 000 40171 9965 000 40171 9965 000 40178 9965 000 40178 9965 100 07707 9965 000 40171 9965 000 40157 9965 000 41112 9965 000 40157 9965 000 40172 9965 000 40172 9965 100 05388 9965 100 05388 9965 000 40180 9965 000 40180 9965 000 41097 9965 000 41097 9965 000 40171 9965 000 40157 9965 100 05388 1F 20% 50V 0.47F 10% 63-100V 4.7F 20% 16V 0.22F 50V 10F 20% 16V 4.7F 20% 16V 4.7F 20% 16V Mylar 0.015F 100V 10F 20% 16V 10F 20% 16V 1F 20% 50V 1F 20% 50V 0.047F 50V 10F 20% 16V 0.1F 50V 4.7F 20% 16V 0.1F 50V 100F 20% 16V 100F 20% 16V 1F 20% 50V 1F 20% 50V 2.2F20% 50V 2.2F20% 50V 100pF 50V 100pF 50V 10F 20% 16V 0.1F 50V 1F 20% 50V
ce
IC101 IC201 IC202 IC301 IC401 IC402 IC601 9965 000 40249 9965 100 07701 9965 000 40597 9965 100 04918 9965 000 40596 9965 100 04917 9965 100 04916 KA33V uP 8k-BIT IIC EEPROM TDA4865AJ DBS7P TDA9859 TFA9842AJ PHILIPS STR-W6554A SANKEN
b
J807 J808 9965 100 04921 Peaking Coil 56H 10% 9965 100 04921 Peaking Coil 56H 10%
SK4.0L CA
10.
EN 55
ce
IC801 IC802 Q801 9965 100 07712 TDA9850 (IIC Bus) 9965 100 07713 L78L09CZ SGS TO-92 9965 000 40232 2SC1815Y/2PC1815
EN 56
11.
SK4.0L CA
Revision List