Você está na página 1de 2

FN.

Lab 1
Scenario
Your organization has two sites are HNI and HCM. Each site has a local WEB server, local DNS
server and own line which connects to the Internet . The DNS server must be accessed locally. You
have to configure as requirements to finish this Skill exam.

The Parameters
Table 1
Device/ Interface
S0
S1

FRAME-RELAY
DLCI= 102
DLCI= 201
Encapsulation: IETF
Type of LMI: Q933a

Table 2
Device
HNI

S0/0/0
S0/0/1
Fa0/0
Fa0/1

IP address
100.100.1.1
10.10.10.1
172.16.1.1
192.168.1.1

Network/Prefix
100.100.1.0/30
10.10.10.0/24
172.16.1.0/24
192.168.1.0/24

Default Gateway
N/A
N/A
N/A
N/A

HCM

S0/0/0
S0/0/1
Fa0/0
Fa0/1

100.100.2.1
10.10.10.2
172.16.2.1
192.168.2.1

100.100.2.0/30
10.10.10.0/24
172.16.2.0/24
192.168.2.0/24

N/A
N/A
N/A
N/A

HNI.ISP

S0/0/0
S0/0/1

100.100.1.2
200.200.200.2

100.100.1.0/30
200.200.200.0/30

N/A
N/A

HCM.ISP

S0/0/0
S0/0/1

100.100.2.2
200.200.200.6

100.100.2.0/30
200.200.200.4/30

N/A
N/A

S0/0/0
S0/0/1

200.200.200.1
200.200.200.5

200.200.200.0/30
200.200.200.4/30

N/A
N/A

NIC

200.200.200.254

200.200.200.248/29

200.200.200.249

NIC

200.200.200.253

200.200.200.248/29

200.200.200.249

NIC

192.168.1.254

192.168.1.0/24

192.168.1.1

NIC

192.168.1.253

192.168.1.0/24

192.168.1.1

NIC

192.168.2.254

192.168.2.0/24

192.168.2.1

NIC
NIC
NIC
NIC
NIC
NIC

192.168.2.253
Dynamic
Dynamic
Dynamic
Dynamic
Dynamic

192.168.2.0/24
172.16.1.0/24
172.16.1.0/24
172.16.2.0/24
172.16.2.0/24
200.200.200.248/29

192.168.2.1
172.16.1.1
172.16.1.1
172.16.2.1
172.16.2.1
200.200.200.249

ISP
Pub.HTTP
(www.isp.com)
Pub.DNS
HNI.HTTP
(www.hni.com)
HNI.DNS
HCM.HTTP
(www.hcm.com)
HCM.DNS
PC1
PC2
PC3
PC4
Pub.user

Interface

Table 3
Device
HNI
HCM
ISP

DHCP
DNS server
192.168.1.253
192.168.2.253
200.200.200.253

Network address
172.16.1.0/24
172.16.2.0/24
200.200.200.248/29

Default-router
172.16.1.1
172.16.2.1
200.200.200.249

Table 4
Items
Console
Enable Secret
SSH (module:1024 bits)
PAP (HNI-HNI.ISP)
PAP (HCM-HCM.ISP)

Username

admin
hni
hcm

Password
cisco
cisco
@.admin
@.hni
@.hcm

1. Task1: Basic Configurations


1) Assign the appropriate IP addresses to the device interfaces following as the given in
Table 2.
2) Configure the Frame-Relay connections, using the correct DLCIs in the Table 1.
3) Enable EIGRP AS 33 on the Router HNI and HCM, routing between both domains via
the Frame-Relay link.
4) On Router HNI and HCM: configute the static default route via the HNI.ISP or HCM.ISP
properly.
5) On Router HNI.ISP, HCM.ISP and ISP: enable OSPF.
6) Enable PAP authentication one-way on the serial link between:
- Router HNI.ISP (as the PAP server) and Router HNI (as the PAP client).
- Router HCM.ISP (as the PAP server) and Router HCM (as the PAP client).
7) Active the suitable services on the all servers. The local server HNI.DNS and HCM.DNS
serves only for the domain the server located. Server Pub.DNS serves for Internet users
only.
8) Configure Router ISP, HNI and HCM as a DHCP server, using Table 3
9) The PC client obtains an IP address and DNS server address automatically.
2. Task2: Advanced Configurations
1) Configure NAT/PAT properly on Router HNI, HCM. So, inside users at the domain can
access the Internet.
2) Internet users can access the WEB servers:
- HNI.HTTP (www.hni.com) by the public IP address 100.100.1.1
- HCM.HTTP (www.hcm.com) by the public IP address 100.100.2.1
- Note: using port-forwarding configuration.
3) On Router HNI and HCM, configure a correct ACL that dont allow Internet users PING
into domain HNI or HCM.
4) Open the SSH service on all the Routers, using Table 4

Você também pode gostar