Escolar Documentos
Profissional Documentos
Cultura Documentos
Part II
Sections VI-X
Section VI
Sound and
Doppler Effect
Section VII Fluids and Solids Section VIII Electrostatics and
Electromagnetism
Section IX
Electricity and
Electric Circuits Section X
BERKELEY
Urevmews
Specializing in MCAT Preparation
The
ERKELEY
R E V
Phone:
Internet:
I E W
(5 10) THE-TEST
http://www.berkeleyrevievv.com
The Berkeley Review and The Berkeley Review logo are registered trademarks of The Berkeley Review. This publication for The Berkeley Review was written, edited, and composed on a desktop publishing system
text type and display type was set in Times Roman and Palatino.
art was created using numerous graphics programs designed for use on Macintosh computers. The majority of the
Cover Design by MacGraphics.
using Apple Macintosh computers and Microsoft Word. Pages were created on the Apple LaserWrite Pro. Line
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the
copyright owner.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
Table of Contents
6. Sound and Doppler Effect
Production and Detection of Sound
Speed of Sound
page 23
page 28
page 33
page 44
7.
page 55
page 66
page 78 page 83 page 89
page 93
page 104
page 115
page 120
page 131
page 141
page 176
page 184
page 188 page 199
page 201
page 206
page 238
page 246
Sound and
Doppler Effect
Physics Chapter 6
'source A
A)
Compressed Wave: Shorter X Higher/ Elongated Wave: Longer X Lower/
source
by
the
Berkeley Review
6 = 10 log (Jsound/j )
closed P*!** ^n =4L/n ' /n =nv/4L> where nis 1. 3 5 etc Important Concept
Echolocation (Using the time to detect echoing sound waves to establish position of an object)
Echo Detector
IP
tj (time for reflection to return from 1st boundary):
used to determine distance to first interface
m
.-. .v-;;
FS^
If the objects are moving towards one another, then the frequency of the wave will increase. This will require either adding to the numerator in the Doppler equation (if the receiver is in motion) or subtractingfrom the denominator in the Dopplerequation (if the sender is in motion). If the objects are moving away from one another, then the frequency of the wave will decrease. This will require either subtracting from the numerator in the Doppler equation (if the receiver is in motion) or adding to the denominator in the Doppler equation (if the sender is in motion).
2) Second determine if the scenario involves one direction transmission or an echo
If it's a one-direction wave only, then you need only plug into the Doppler equation once. If it's an echo, then you'll need to plug into the Doppler equation a second time, using the first solved frequency as the input frequency and reversing the roles of the sender and receiver from the first
wave. In other words, the sender of the outbound wave becomes the receiver of the inbound wave.
Physics
Sound
Sound
In Chapter 5, we studied standing waves on a string. In this chapter, we shall expand our coverage of waves to include sound waves, one example of a
longitudinal wave.
arises from the vibrations and collisions of molecules within a particular substance. Even though these molecules maintain their same average position
within that substance, the collision of one molecule with another molecule results
in the transmission of energy in the form of a wave. Sound waves cannot travel through a vacuum. Sinusoidal waves are the simplest type of sound waves. They have a defined wavelength, amplitude, and frequency. In order to detect a sound wave, the
The human ear is an excellent sound detector and can distinguish sounds that differ in frequency from one another by as little as 0.3%. A simplified version of the human ear is shown in Figure 6-1. The pinna (outer ear) collects sound waves and funnels them into the auditory canal. As the sound waves press on the tympanic membrane (eardrum), they cause the membrane to vibrate. This vibrational energy is transmitted through the ossicles, three small bones (hammer, anvil, and stirrup) connecting the tympanic membrane to the oval
window of the inner ear.
Pinna
Tytripinric
(eardrum)
(outer car)
Oval ^_ Basilar
window/ membrane
High
frequencies
Low
Auditory
canal
frequencies
Figure 6-1
As the ossicles vibrate, they amplify the vibrational energy set in motion at the tympanic membrane. This vibrational energy is passed from the oval window to a fluid in the cochlea of the inner ear. The fluctuations in pressure in this fluid
cause hair cells in the basilar membrane of the cochlear duct to move. Movement
of the hair cells generates a nerve impulse that is sent to the brain and is interpreted as sound. High frequency sounds are generated by nerves closest to the oval window, while low frequency sounds are generated by nerves farthest away from the oval window.
Physics
Sound
Speed of Sound
Speed of Sound
When a sound wave moves forward, it compresses the medium in front of it. This results in compressional waves moving outward in all directions from the source of the sound. Consider the compressional wave in Figure 6-2. Note that as the wave moves outward, there are regions of high density (or high pressure) and low density (or low pressure) within the medium. Also note that the volume of space associated with the regions of high density decreases relative to the volume of space associated with the regions of low density. The region of reduced pressure is also called a rarefaction.
Propogation of wave
=>
/:
high density
low density
Figure 6-2
Solids, Liquids, and Gases
The speed with which particles can return to their original position following a disturbance in the medium dictates the speed of sound in that medium. The strength of the forces between the molecules in a given medium and the density of the particles in that medium determine how fast sound will travel in that medium. The forces between the molecules in a solid are greater than the forces between the molecules in a liquid or a gas. The stronger the force between any two molecules, the greater the restoring forcebetween those molecules. The more rapidly molecules are restored to their original condition, the more rapidly they can participate in another compression wave, and the faster the propagation of
sound in that particular medium. As a result, we see the general trend for speed or sound as vsoun(j jn solid > vsouncj mliquid > vsouni jn gas.
The speed of longitudinal sound waves in various ideal gaseous media can be
calculated from the formula in equation (6.1):
(6.1)
In this equation, pis the density (of a gas), Pis the pressure (of a gas), yis Cp/Cv
(where Cp is the molar heat capacity at constant pressure, and Cv is the molar
heat capacity at constant volume for a gas), R is the ideal gas constant, T is temperature in kelvins, and M is the molecular mass of the gas. For a monatomic
gas y = 1.67, for a diatomic gas y = 1.40, and for a polyatomic gas y = 1.33. This means that for a given pressure and gas density, a monatomic gas will permit sound to travel through it at a greater speed than a diatomic or polyatomic gas will. For example, if the temperature of the air is 0 C, the pressure is 1 arm (or
1.01 x105 N/m2), and the density is1.29 kg/m3, then the speed ofsound inair is
331 m/s. In this case, we are making the assumption that the air is composed of gases in the diatomicstate, becauseair is predominantly N2 and O2.
v =
=331 m/s
Physics
Sound
Speed of Sound
In Table 6.1, we see the speed of longitudinal sound waves in various media.
These values may vary from textbook to textbook, depending on whether the author assumed isothermal or adiabatic conditions. For the MCAT, knowing that thespeed ofsoundin air at roomtemperature is about340 m/s is goodenough.
Table 6.1
Material Air
Air
Air
Temperature / Pressure
(0C, 1 arm) (20Q 1 arm)
(100C, 1 arm) (0C, 1 arm)
Speed (ms)
331
340
386
Hydrogen
Helium
1286
965 1497
1531
(0C, 1 arm)
Water (lake)
Water (sea)
Aluminum
Iron
5100 5130
Glass
Granite
5500
6000
In Table 6-1, note that the speed of sound in metals and liquids is much greater than the speed of sound in air. This is due to the fact that metals and liquids are not as compressible as gases. Therefore, the restoring forces for a metal or a
Which of the following changes will increase the speed of sound in a fixed volume of diatomic hydrogen gas that is enclosed in a fixed-volume container? I. Increasethe temperature of the gas.
Increasing the temperature of the gas in this enclosed volume will increase the molecular kinetic energy without changing the molecular inertia (i.e., mass density). Thus, Statement I is true, and choice B is wrong. Replacing the hydrogen with oxygen will noticeably increase the massbut, presumably, change the molecular interaction forces little. This would reduce the speed of sound, invalidating Statement II. We are left to conclude that choice C is the correct choice. Statement III must be valid, if the above equation is to hold true.
The best answer is choice C.
PhysiCS
Example 6.1b
Sound
Speed of Sound
An acoustic scientist measures the properties of three unknown molecules, labeled A, B, and C. He records the following relationships for the molecular weights and cohesive forces of the molecules:
MWa > MWb = MWc and Fa < Fr < Fc
These relationships hold true, regardless of the state of the material. Noting these results, which of the following relationships could he predict regarding the speed
of sound in these materials? (Assume all solids have the same lattice structure
III. Speedof sound in Liquid C is greater than that in Liquid A, when Liquid A is hotter than Liquid C.
A. II only B. I and III only C II and III only
D. I, II, and III
Solution
The speed ofsound within a medium depends on the ability ofthe particles that make up the medium to quickly return to their original position following a disturbance. The restoring speed of the particles depends on the force holding particles together (cohesive force) and the mass of the particles. Lighter particles are made of lighter particles, assuming all other factors are equal. The question also mentions forces. The stronger the forces between particles (stronger intermolecular forces), the faster the particles can return to their original position
move faster than heavier particles, so speed of sound is faster in mediums that
Particle Cis the lightest and has the strongest intermolecular forces, the speed of
sound will be fastest in Medium C when the temperature is uniform. This makes
Statement II a true statement, which eliminates choice B.
Statement III is invalid, because without knowing the temperature (or knowing thatif s equal for all mediums), we do nothave enough information to determine the relative speeds of sound. This eliminates choices Cand D, leaving only choice
sound. Thisfurther supports the elimination of choices Band D.
This makes choice A the best answer.
and is the heaviest particle, resulting inMedium A having the smallest speed of
Physics
Pitch and Intensity
Sound
There are many subjective terms used to describe sound, such as pitch. This word is used to describe an individual's impression concerning the frequency of a particular sound. For example, if a musical instrument has a high pitch, then the sound waves coming from that instrument vibrate at a high frequency. Conversely, if a musical instrument has a low pitch, then the sound waves coming from that instrument vibrate at a low frequency. Human ears process
sound waves with a frequency between 20 Hz and 20,000 Hz.
Sounds can be distinguished not only by their pitch, but also by their loudness. The subjective loudness of a sound is usually expressed objectively in terms of its intensity (I). Figure 6-3 shows a reference wave and four waves that represent variation in the properties of a sound.
2A
Reference Sound
u
Quieter Sound
Lower Pitch
Figure 6-3
The intensity of a sound wave is the power (P) that the wave transports per unit
area (A) of its wavefront, as shown by equation (6.2). Remember, power is just
energy per unit time. This means that the intensity of a wave will have units of
energy (in joules) divided by the units of area (in m2) times the time (in seconds).
Therefore, the units of intensity are J/(m2s). However, recall that a watt is just a
Energy (Area)(Time)
_ Power
Area
(6.2)
We can also compare the intensity (I) of any particular sound with the intensity (I0) of a reference sound, the minimum sound intensity an average human ear
can detect. The intensity of the reference sound is chosen to be 10"12 W/m2. This
comparison of I to IQ is referred to as the intensity level (f3) and is given by equation (6.3). The reason that a logarithmic scale is used is because the human
ear is sensitive to a broad range of intensities that spans many powers of 10. The
unit used toexpress the intensity level ofa sound is the decibel (abbreviated dB).
C=10 log i
In
(6.3)
Physics
Sound
The intensity of sound dissipates with distance by a squared factor. As such, the intensity of a sound drops off rapidly at first, it can still be heard from a long distance away. You may have noticed this when stepping away from a loud stereo speaker. It quickly goes from painfully loud to acceptable within a few steps, but you can likely hear that speaker from blocks away. As a general rule, every time the distance from the source is increased by a factor of 3.2, the intensity drops by a factor of 10, so the dB-level decreases by 10. Figure 6-4 shows this relationship.
Distance (m)
Figure 6-4
Listed in Table 6.2 are theintensity and intensity levels ofsome common sounds.
Table 6.2 Sound Intensity (W7i*2)
103
1
Threshold of pain
Busy street traffic
Normal conversation
Quiet room
A whisper
20 0
Threshold ofhearing
The data in the table confirms that for every drop in intensity by a factor of 10, the decibel level decreases by 10. For instance, if the intensity of a sound'
increase by 30 (3 x 10).
increases by 1000 (three factors of 10), then the decibel level of that sound will
10
Physics
Example 6.2a
sound
An annoying neighbor who owns a stereo system has just heard his favorite song begin to play. He turns up the stereo so that the intensity is now 16 times louder than it was before the song started. By how much does the intensity level
increase?
A. B. C. D.
The intensity level increases by The intensity level increases by The intensity level increases by The intensity level increases by
Solution
First, know that intensity and intensity level have different units. This rules out choice C, since increasing the intensity of a sound by a factor of 16 would not lead to a 16-dB increase. You can use equation (6.3), if you are good at calculating base-ten logs. If not, here is an easy way to thinkabout these intensity scales:
If the intensity increases by a factor of 10, then the intensity level increases by 10 dB. If the intensity increases by a factor of 100, then the
intensity level increases by 20 dB.
If the intensity decreases by a factor of 10, then the intensity level decreases by 10 dB. If the intensity decreases by a factor of 100, then the
intensity level decreases by 20 dB.
Here, the intensity increases by a factor of 16. The corresponding intensity level
increase must be somewhere between +10 dB and +20 dB, but closer to 10 dB
than 20dB. Only choice Bis possible. To solve this more precisely,
While you are discussing the virtues of antisound in a medical library, the librarian asks you to be quiet. In going from a talk to a whisper, the intensity level ofyour voice decreases from60dB to 20 dB. By what factor doesyour voice
correspondingly decrease in intensity? A. B. C. D. The intensity decreases by a factor of 30. The intensity decreases by a factor of 40. The intensity decreases by a factor of 100. The intensity decreases by a factor of 10,000.
Example 6.2b
Solution
The sound drops by 40 dB, so we need to use the decibel relationship to determine the magnitude of the drop. Because AdB = 10 log If/I0/ we can solve for the magnitude by dividing by 10and then taking an analog.
11
Physics
Sound
Doppler Effect
Doppler Effect
If you have ever been near a fast-moving car as it went whizzing past you, then you have probably noticed that as the car approaches you, you hear a highpitched whining sound from the enginebut as soon as the car passes you, the pitch quickly becomes much lower and fades out. There is a change in the
intensity of the sound with distance, as well as a perceived change in the frequency of the sound. The change in pitch of a sound from a high frequency as it approaches an observer to a low frequency as it moves away from the observer
is called the Doppler effect.
Let's consider what happens when the source of the sound is stationary and a listener is moving towards that sound. Suppose that you are walking towards
an idling car. You move at a speed vl ("L" refers to the listener) towards the
stationary car. The engine of the car is emitting sound waves with frequency /s (where the subscript "s" refers to the source). This scenario is depicted in Figure
6-5.
car (Figure 6-5) have wave fronts all separated from one another by an equal
distance X. wave front
Note that the sound waves coming from the engine located near the back of the
/rTm////^//////////W)%////////////////////7/////^7///////// X
Figure 6-5
As you approach the car, the wave fronts appear to move towards you with a speed of v + vl- When the wave fronts arrive at your position, you encounter each subsequent wave front at a point that is slightly closer to the source than
where you encountered the previous wave front. Although the wavelength of the
and the actual sender frequency (fs) for a scenario where the listener is moving
towards a stationary source.
fL =
v + vL
closer together than they really are. This leads to a perceived shorter wavelength. It also leads to a perceived increase in frequency that varies with your speed. Equation (6.4) represents the relationship between the observed frequency (/jj
waves emitted from the source are constant, you perceive the wave fronts to be
fs
(6.4)
Equation (6.4) is telling us that if you move towards the source of the sound (i.e.,
vl > 0), then you hear a higher pitch (corresponding to a greater frequency). If
you move away from the source ofthe sound (i.e., vl < 0), then you hear a lower
pitch (corresponding to a smaller frequency). This should match nicely with what you've experienced inreal life interms of the Doppler shift.
12
Physics
Sound
Doppler Effect
A good analogy to help comprehend the Doppler effect is to consider what would happen if you were to toss jellybeans to a friend at a frequency of one jellybean per second. If you were both stationary, then your friend would receive
one jellybean per second. Now if you were to walk towards them while still throwing one jellybean per second at the same speed, your friend would receive the jellybeans at a frequency greater than one per second, because each time you released one, you would be a little closer to your friend than when you threw the last one. While your throwing would have a frequency of one per second, your friend's perceived reception frequency would be higher and would depend on the speed with which you walked towards them. Let's now consider what happens when the source of the sound is moving and the listener is stationary. The source of the sound is the car's engine, and the car moves with a velocity vs, as shown in Figure 6-6. Even though the car is now
moving, the speed of the sound waves does not change. The speed of those
sound waves is still v. wave front
vL = 0
////////////////////////////////J////////////
Figure 6-6
11
As the car approaches you, each subsequent wave front initiates from a point that is closer to you at the time it is released. When the wave fronts arrive at your
position, you encounter each subsequent wave front at a point that is slightly
closer to the source than where you encountered the previous wave front.
Although the wavelength of the waves emitted from thesource are constant, you perceive the wave fronts to be closer together than they really are. This leads to a perceived shorter wavelength. It also leads to a perceived increase in frequency that varies with the speed of the car. Equation (6.5) represents the relationship between the observed frequency (/l) and the actual sender frequency (/s) for a
scenario where the listener is moving towards a stationary source.
(6.5)
*-(r?d'
Equation (6.5) is telling us that the source of the sound moves towards you (i.e., vs > 0), then you hear a higher pitch (corresponding to a greater frequency). If
the source of the sound moves away from you (i.e., vs < 0), then you hear a lower
wave fronts. If we combine equations (6.4) and (6.5), we get equation (6.6). This is
the general equation for the Doppler effect. It shows how the frequency of the
sound waves encountered by the observer (f\J is related to the frequency of sound waves emitted by the source (/s).
(6.6)
13
Physics
Sound
Doppler Effect
Since this is an important equation, let's define its variables once again:
vl Speed of the listener relative to still air vl is positive(+), if the listener is moving towards the source.
vl is negative (-), if the listeneris moving away from the source. vs Speed of the source relative to still air vs is negative (-), if the sourceis moving towards the listener. vs is positive (+), if the sourceis moving away from the listener.
If the listener and the source ofa sound are moving toward one another, then fL
will always be greater than fs. However, if the listener and the source of a sound
are moving away from oneanother, then ft willalways be less than fs.
Example 63a
The spectra of starlight tell astronomers about the chemical makeup of stellar
bodies. However, the visible spectral lines may be shifted away from their usual
spectrum) isknown asa red shift. Ashift towards tohigher frequencies (the blue end of the visible spectrum) is known as a blue shift. If an astronomer notices
that the spectrum ofa particular star isblue-shifted, then the:
I. star could be moving towards the Earth. II. star could be moving away from the Earth. III. Earth couldbe moving towards the star.
frequencies. A shift towards to lower frequencies (the red end of the visible
Solution
To identify a Doppler effect problem, note the following: 1. Any type of wave can undergo a Doppler shift-sound, light, water,
earthquake, anything whatever.
2.
3.
5.
When the source and detector recede from each other, the detected
frequency is lower than the emitted one.
The spectrum is blue-shifted, so the detected frequency must be higher than the
emitted one. The starand the Earth mustbe getting closer to one another.
The best answer is choice C.
14
Physics
Example 6.3b
Sound
Doppler Effect
A bat emits an ultrasonic squeak in the direction of an insect and notices that the reflected sound is of a lower frequency than the emitted pulse. What could BEST explain this frequency shift?
A. B. C. D. The bat is moving towards a stationary insect. The insect is moving away from a stationary bat. Either the bat or insect is moving toward the other. Either the bat or insect is moving away from the other.
Solution
The reflected ultrasonic wave has a lower frequency than the emitted ultrasonic wave, so the pulse must have undergone a Doppler shift of some kind. A lower frequency for the echo indicates that the bat and the insect must be getting farther away from one another as the ultrasonic wave propagates. Both choices B
and D describe a scenario where the distance between the bat and the insect is
increasing. Under such a situation, it comes down to test-taking logic. You have to ask yourself what the test writer wants you to pick. Choice D is more general
than choice B and accounts for more possibilities than choice B. In other words,
choice Bmight explain it while choice likely will explain it. The betterchoice here
is the answer that explains it under more scenarios.
The best answer is choice D.
questions involving the Doppler effect, it is a good idea for you to ask yourself
two questions:
1) Is the wave being analyzed an echo or a single directionwave? 2) Are the senderand receiver moving towards or awayfrom one another?
Consider the bat and insectfrom Example 6.3b. The answer to the two questions above is that ifs an echo that is being detected and that the two are moving away from one another. Let's say for sake of argument that the bat is moving away
from a stationary insect at a speed of 17m/s. To determine the frequency of the echo, we will do a two-step analysis determining first the frequency detected by the insect, and then determine the frequency of the echo detected by the bat. We shall use f0 to represent the emitted frequency by the bat, f\ to represent the frequency detected by the stationary insect, and /2 to represent the frequency of
the echo detected by the moving bat.
equation to the echo equation, because the direction of the wave changed from opposing the bafs motion to complementing the bafs motion. It ends up that for an echo, we cansimply plug into the Doppler equation twice, which makes these questions easier to solve than we may have initially imagined. Just be sure to plug the numbers in such a way as to make the shifted frequency either higher or
lower, according to their relative motion. Copyright by The Berkeley Review
15
You should note that the sign for the bafs speed changes from the outbound
Physics
Sound
sources of the sound, most of them produce vibrational energy at frequencies well within the range of human hearing (20 Hz to 20,000 Hz). Two possible sources of the kinds ofsounds we will be considering in this section are stringed
musical instruments and wind musical instruments. These instruments can
produce sounds with numerous natural frequencies (also called resonant frequencies) of vibration.
Resonance in Strings
Consider a guitar string of length L, which is fixed at two ends and is under a certain tension. Byfixed, we mean that it is held in place so it cannot move. If we
were to pluck this guitar string, a wave pulse would be sentdown the length of
the string and reflect off of one ofthe fixed ends. The guitar string would begin to vibrate. If the string vibrated at a particular natural frequency, a standing
without propagating.
appear tomove ineither direction along the length ofthe string. Standing waves are produced from waves traveling in opposite directions along a string that combine toproduce a wave disturbance, which appears to oscillate up and down
wave would be produced (Figure 6-7). A standing wave is a wave that does not
Figure 6-7
wavelength apartfrom each other. At a node, the pulses ofa wave interfere with
displacement of a string ata node is always zero. A point along the string that reaches maximum displacement is called an antinode. The two ends of the string in Figure 6-7 are nodes. Adjacent nodes along the string are always one-half
A point along the string thatis never displaced is called a node. In other words,
waves that had already been produced along the string would notbe affected.
each other in a destructive fashion. If a node on a guitar string were suddenly fixed in place (by pressing the string against a fret with a finger), the standing
equations to find the natural resonant frequencies of a fixed string and their
regions of maximum displacement of the vibrating string. In a standing wave both the nodes and the antinodes are atfixed points along the string. In Figure 6-8 are the first four natural frequencies for a string fixed at both ends. In equations (5-17) and (5-18) of Section V, we derived the expression for both the frequency and the wavelength of fixed-end strings. We can use these
There are also regions along the string where the wave pulses add in a constructive fashion. Those regions are called antinodes, and they are located halfway between two nodes. Another way to look at this is to say that an
number ofthe associated wave, and it must be a whole number. Every harmonic frequency isalways a whole number multiple of the fundamental frequency, /n
= n/i.
Harmonics: Frequencies that are integer multiples ofthe fundamental frequency (i.e., /i) are called harmonics. In musical terms, frequencies greater than f\ are
called overtones. Forexample, the frequency /2 is the second harmonic, but it is
the first overtone.
16
Physics
Standing Wave
1st Harmonic
Sound
Frequency
Wavelength
Xi=2L
(Fundamental)
2nd Harmonic
(1st Overtone)
3rd Harmonic
(2nd Overtone)
4th Harmonic
(3rd Overtone)
Figure 6-8
Example 6.4a
What is the beat frequency created upon interference ofthe third harmonic with
the fifth harmonic of waves on a fixed string?
A. B. C. D.
The beatfrequency would equal the frequency ofthe second harmonic. The beat frequency would equal the frequency ofthe eighth harmonic. The beat frequency would equal the frequency ofthe fourth harmonic. The beatfrequency wouldnot correlate to any oftheharmonics.
A beat frequency equals the absolute value of the difference between the two interfering frequencies. Because all of the harmonics are multiples of the fundamental frequency (first harmonic), the beat frequency will also be a whole number multiple of the fundamental frequency. This eliminates choice D. The beat frequency is found as /beat = ' /5 - ft' = 15/i - 3ft I = 2/i = ft. The beat frequency isthe second harmonic, making choice Acorrect.
The best answer is choice A.
Solution
What is the fundamental frequency for a string fixed at both ends that produces
consecutive harmonics of 114 Hz, 171 Hz, and 228 Hz?
A. B. C. D. 114 Hz 228 Hz 57 Hz 19 Hz
Example 6.4b
Solution
Consecutive harmonics differ by the fundamental frequency, ft = /n - /(n-1)This means that we simply need to subtract 171 Hz from 228 Hz, or subtract 114
Hz from 171 Hz. The difference is 57 Hz, so the fundamental frequency is 57 rlz.
The best answer is choice C.
17
Phy S1CS
Sound
Resonance in Pipes The formation of standing waves in pipes is similar to the formation of standing
waves along a string. Instead of plucking the string as we did in the case of the
guitar, we blow air across an open end in the pipe. By blowing across this open end, we produce a pressure pulse of air that travels down the pipe. There are two types of pipes to consider: an open pipe, in which both ends are open; and a closed pipe, in which one end is closed and the other end open..
trumpet, or an oboe). If we blow across one of the open ends of the pipe shown leave the pipe and part ofit will be reflected back into the pipe (Figure 6-9b). The pressure pulse thatis reflected intothe pipeis a pulse ofdecreased pressure, and it travels back towards its origin. When it reaches the opening at the left end, part of the pulse will leave the pipe and part of the pulse will again be reflected down the pipe (Figure 6-9c). The reflected pressure pulse again changes direction and becomes an increased pressure pulse traveling down the pipe to the right (Figure 6-9d). Upon reaching the right side, the pulse reflects again (Figure 6-9e); a low pressure pulse now travels back to the left (Figure 6-9f). Upon reaching the left side, the pulseagain reflects and repeats the cycle (Figure 6-9a).
Initiation of Pressure Pulse (High Pressure)
(a)
open
end
Open Pipe: Suppose we have a pipe that is open at both ends (like a flute,
in Figure 6-9a, a pressure pulse of air will be sent down the length of the pipe. When this pressure pulse reaches the right end of the open pipe, part of it will
M
reflects
open
end
(d)
H
Reflection of Pressure Pulse (Low Pressure)
&1
(e)
- '- continues
(c)
<=
reflects
!=>
(f)
'
11
Figure 6-9
If a new pressure pulse of air were to be sent down the pipe, it could interfere
with the initial pressure pulse in either a constructive or a destructive manner. If
the new pressure pulse interferes constructively, the pulse's amplitude increases.
Pressure pulses can be represented as waves. The waves for the first two normal
an open pipe there will be an antinode. All of the harmonics frequencies must also meet the restriction of having antinodes at each end ofthe pipe. The distance between two adjacent antinodes isalways one-half of a wavelength.
L =
2X
mode frequencies for an open pipe are shown in Figure 6-10. At both openings of
open
end
Figure 6-10
18
1 iiySlCS
Sound
Thus, the length of an open pipe is one-half of the fundamental wavelength and can be given by equation (6.7). Solving equation (6.7) for the wavelength and then substituting into the basic equation for a wave (v = Xf) gives equation (6.8). This is the lowest frequency mode (i.e., fundamental frequency mode) for a pipe that is open at both ends.
L = h.
2
(6.7)
(6.8)
/ = JL
2L
Open pipes can vibrateat all multiples of the fundamental frequency. Therefore, an open pipe can vibrate at the standing wave frequencies shown in equation
(6.9). In this equation, n = 1,2,3,...
Open Pipe
^-"(i)
(6.9)
Example 6.5a
Which of the following changes will NOT increase the frequency of a sound wave produced by a pipe that is open at both ends? A. B. C. D. Increasing the temperature of the air in the pipe Using pipe material with rhombic crystallization rather than monoclinic Lengthening the pipe Shortening the pipe
Solution
by either decreasing the pipe'slength or by increasing the wave's speed. Choice D increases the frequency, so it is eliminated. Conversely, lengthening a pipe will decrease the frequency of the waves it produces. Lengthening the pipe does not
increase the frequency of the wave, so choice C results in a decreased frequency.
For choice A, the speed of a sound wave in a pipe increases as pipe temperature
increases. Choice B requires test-taking logic. There is no doubt that the crystal structure of a material impacts the wave a pipe will propagate, but there's no way 99.99% ofpeople taking the MCAT would know the details. It comes down to knowing that it couldbe right and not gettinghung up on not knowing a fact.
The best answer is choice C.
Example 6.5b
The wavelength of each harmonic is equal to 2L/n, where L is the length of the string and n is the harmonic number. In this case, the harmonic is found as
2(2)/3 = 4/3 m. The best answer is 1.33 m. You could also have reached this conclusion looking at Figure 6-10 and drawing the next wave in sequence.
The best answer is choice B.
Solution
19
Physics
Sound
open end of the pipe shown in Figure 6-lla, a pressure pulse of air will be sent down the length of the pipe as it was in the open pipe. The difference with a closed pipe compared to an open pipe is that the wave pulse will reflectoff of the closed end. The pulse hits the closed end of the pipe (Figure 6-llb) and is reflected toward the open end with no changein phase.
As the pulse reaches the open end of the pipe, it is reflected toward the closed end again (Figure 6-llc). At this point, a change of phase has occurred; there has been a decrease in pulse pressure (Figure 6-lld). The decreased pulse returns to
the closed end of the pipe and is reflected again (Figure 6-lle). Once the pulse reaches the open end ofthe pipe, there is again a change in the phase ofthe pulse
(Figure 6-llf); the pressure increases, and we are back at Figure 6-lla. Therefore, the phase ofthepulse isinverted once with each round trip.
Initiation of Pressure Pulse (High Pressure)
(a) open
end
H
<="
closed end
hi
(b)
(e)
(0
(f)
Figure 6-11
The first two normal mode frequencies for a closed pipe are shown in Figure 612. At the opening of the pipe there will be an antinode, while at the closed end
of the pipe there will be a node. The antinodes are where the air pressure fluctuates maximally; the nodes are where the air pressure does not vary at all
from atmospheric. The distance between a consecutive antinode and a node is always one-quarter ofa wavelength.
closed end
open end
Therefore, the length of the closed pipe is one-quarter of the fundamental wavelength and can be given by equation (6.10). A harmonic frequency can be related to the corresponding harmonic wavelength by using the basic wave
equation, v = Xn-/n. Solving equation (6.10) for the wavelength and then substituting into /n = v /Xn gives equation (6.12). As we see, the fundamental
for a pipe of equal length that is open at both ends.
Copyright by The BerkeleyReview
frequency for a closed pipe turns outtobe one-half ofthe fundamental frequency
20
Physics
L=^
4
Sound
(6.10)
/ = JL
4L
(6.11)
A closed pipe cannot vibrate at twice the fundamental frequency. Why? If we were at twice the fundamental frequency, then a pressure pulse would have traveled to the closed end of the pipe and back to the open end before another pressure pulse couldbe initiated. Recall that the pressure pulse was inverted as it came off of the closed end of the pipe. If this inverted pressure pulse encounters a new pulse, there will be destructive interference. Even though a closed pipe cannot vibrate at even multiples of the fundamental frequency, it can vibrate at odd multiples of the fundamental frequency. Therefore, a closed pipe can vibrate at the standing wave frequencies shown in equation (6.12). In this equation, n =
1,3,5,....
Closed Pipe
/n=n(i)
(6.12)
Example 6.6a
In a study of organ pipes, an engineer charts the frequencies of two equally long pipes when they are made to resonate in various harmonic modes.
n
/PipeA(Hz)
411
/PipeB(Hz)
396
792
1
2 3
822
1233
1188
Solution
The frequency of a sound wave in both an open pipe and a closed pipe depends on the speed of the wave and the length of the pipe. The question states that the pipes are equally long, so the observed differences in frequencies must be due to a difference in the speed of the waves. A variation in the gravitational field would not impact the wave speed (or the wave frequency), eliminating choices C
and D. This means that the difference in wave speed stems from a difference in
temperature. Gases travel fasterin warmer air than cooler air,so the speed on the sound wave through the pipe will be faster in the warmer pipe. Warmer air producesa higher frequency sound wave, so Pipe A must have the warmer air.
The best answer is choice A.
For many of the questions dealing with harmonic frequencies, you will notice a pattern in the numbers. Look for differences between numbers or common denominators when dealing with harmonic frequencies of standing waves. If you can find a highest common denominator, then you have likely found the
fundamental frequency.
21
1 JiySlCS
Example 6.6b
Sound
In studying the relationship between the variable lengths of two openresonating pipes and the number of harmonics eachpipe can produceat different lengths, a
musicologist notices the following trends in her data:
4i
3
n
Pipe A
11
PipeB
L(m)
Pipes A and B are both telescoping pipes. What could explain the difference in slopefor the lines representing eachpipe?
A. The speed ofsound is faster for Pipe A thanfor Pipe B. B. The speed ofsound isslower for Pipe A than for Pipe B.
C. D. Pipe A is wider than Pipe B. Pipe A is narrower than Pipe B.
Solution
Using the equation for the resonant frequencies of an open pipe (/n = nv/2L), you can relate n and Lasn =/n(2L/v). You'll note thatthe width ofthe pipe has
no impact on the frequency of the resonance waves, so choice C and D are
related, and more importantly thata bigger sound speed v results in a smaller
slope in the n-L line. This makes choice B correct and choice A incorrect.
The best answer is choice B.
the precise equation, atleast know the basic variables used init (e.g., realize that width is not an important factor). This way, you've increased your chances of guessing, should you need to. The equation shows that n and L are linearly
eliminated. The pipewidth does notaffect frequencies and resonances other than to decrease the overall intensity of the resulting sounds. If you didn't remember
22
I.
II. III.
Violin Strings
Train Whistle Submarine Sonar
(1-7)
The main purpose of this 25-question set is to serve as a review of the material presented in the chapter. Do not worry about the timing for these questions. Focus on learning. Once you complete these questions, grade them using the answer key. For any question you missed, repeat it and write down your thought process. Then grade the questions you repeated and thoroughly read the answer explanation. Compare your thought process to the answer explanation and assess whether you missed the question because of a careless error (such as misreading
the question), because of an error in reasoning, or because you were missing information. Your goal is to fill in any informational gaps and solidify your reasoning before you begin your practice exam for this section. Preparing for the MCAT is best done in stages. This first stage is meant to help you evaluate how
well you know this subject matter.
4.
A violin produces sound because of the transverse vibrations of its strings, which cause the air around them to vibrate. These longitudinal waves generate the sound that is associated with a resonating cord. The speed of the waves on a violin string is given by the formula:
Equation 1
Violin players can press down on the violin strings effectively to shorten the length of a particular string. The shorter string will produce standing waves which
are:
A. B. C. D.
higher in frequency and shorter in wavelength. higher in frequency and longer in wavelength. lower in frequency and shorter in wavelength. lower in frequency and longer in wavelength.
V M
where T is the tension in the string, L is the length of the string, and M is the mass of the string. This means that the mass of the string actually affects the speed of the waves, which is unusual in that mass usually has no effect on speed.
Each string of the violin produces standing waves with many frequencies, given by:
Equation 2
f = ny_
2L
5.
Which of the following changes would double the fundamental frequency produced by a violin string?
A. B. C. D.
Doubling the tension on the string. Quadrupling the tension on the string. Halving the tension on the string. None of the above changes would double the fundamental frequency.
where n = 1, 2, 3,.... By adjusting the strings, one can alter and control the sound generated by any stringed instrument,
such as the violin. 1.
6.
If the length of a typical violin string is 30 cm, what are the wavelengths of the first three harmonics?
A. B. C. D. 30 cm, 60 cm, 90 cm 30 cm, 15 cm, 10 cm 60 cm, 30 cm, 20 cm 60 cm, 40 cm, 20 cm
Two strings have the same length and fundamental wavelength, but different fundamental frequencies.
What could account for the difference in the
2.
What is the fundamental pitch of a string that has a length of 30 cm, a mass of 30 g, and a tension of 9000
N?
A. B. C. D.
A. B. C. D.
7.
When comparing the standing waves produced on a violin string with the sound waves produced by that
string, we find that:
24
12. As the train approaches a station, it blows both whistles. A person standing on the platform hears both whistles with apparent frequencies f\% and ft. Which of the
following would be TRUE?
A. fl<f2<fl'<ft
B. fl<f2>fl'>ft
C /i</i\/2</2' D. f\<f\\fi>ft
6= 10-log10|
13.
where I = intensity, ID = reference intensity, and 6 is the intensity level in dB. Assume that the speed of sound is 330 m/s in all questions and that f\<ft
8. If the train is in the station and blows Whistle 1 with
0.75 m
1.00 m
C.
D.
1.33 m
0.67 m
B.
9.
B. C. D.
890 Hz -10 Hz 10 Hz
10. Sound wave A has an amplitude of 1 mm and Sound wave B has an amplitude of 3 mm. What are the maximum and minimum possible amplitudes, if A and
B interfere? A.
B. C. D.
D.
3 mm and 1 mm
2 mm and -2 mm 3 mm and -1 mm 4 mm and 2 mm 14.
11. Sound wave A has an amplitude of 1 mm and Sound Whistle 1 has an intensity twice that of Whistle 2. Whistle 1 has an intensity level that is how many dB greater than the intensity level of Whistle 2?
A. B. 3dB 10 dB
The train approaches a tunnel at 20 m/s and blows Whistle 1 when it is 660 m away. How much time elapses between the moment when the whistle is blown and the moment when its echo is heard by the engineer?
A. 2.0 s
B. C.
2.6 s 3.8 s
D.
4.0 s
C.
D.
20 dB
30 dB
25
17.
sonar emits a sound signal and listens for the echo from the
bottom of the ocean or another vessel. If your vessel or the
III. For a fixed frequency, increasing wavelength requires increasing the wave speed.
A. I only B. I and II only C. I and III only
D. I, II, and III
enemy vessel is moving, the frequency of the echo will be Doppler-shifted. The Doppler shift equation for frequency
when both source and observer are moving is:
\v vs/
where v = speed of sound, v0 = speed of observer, vs = speed of source, / = original frequency, and /' = observed frequency. For ease in calculations and measurements underwater, the speed of sound is taken to be 1500 m/s.
Active Sonar
18.
Passive
Sonar
If Submarine CIS is moving at 20 m/s towards stationary Submarine USA, and the passive sonar operator in Submarine CIS is listening for Submarine USA's active sonar pulse, what is the frequency f\ of the active sonar pulse, as measured by passive sonar on
Submarine CIS?
A. B. C. D.
19.
Submarine USA is moving at 10 m/s toward a second active sonar source (SASS). Both Submarine USA and
Figure 1 In Figure 1, assume Submarine USA moves with speed Va and has an active sonar that emits signals with frequency 500 Hz. Assume Submarine CIS moves with speed Vr and
has a passive sonar.
SASS emit the same standard source frequency. If Submarine USA sends out a signal to SASS and then listens to the echo, how would the echo frequency detected by Submarine USA compare to the source
frequency?
A. /echo > /source
B.
3000 m
C.
D.
4500 m
6000 m
20.
Starting with Submarine USA on the left and Submarine CIS on the right, which condition will lead to the LOWEST observed frequency for Submarine
CIS?
16.
the bat's signal compare to the submarine's sonar? A. B. C. D. Bat sonar must have Bat sonar must have Bat sonar must have Bat sonar "musthave a longer wavelength. a shorter wavelength. a lower frequency. a higher frequency.
A. Submarine USA moving to the right at 10 m/s, with Submarine CIS moving to the left at 20 m/s. B. Submarine USA moving to the right at 10 m/s, with Submarine CIS moving to the left at 10 m/s. C. Submarine USA moving to the left at 10 m/s, with Submarine CIS moving to the right at 10 m/s. D. Submarine USA is stationary, with Submarine CIS
moving to the left at 10 m/s.
26
21. In Figure 1, Submarine CIS makes a sudden course change so that now both vessels are moving in the same direction with the same speed va = vjj = 10 m/s. Submarine USA emits a sonar signal with frequency /, and that signal is detected by Submarine CIS with frequency f\. How does f\ compare to /?
A. />/i
22. The fundamental frequency of a pipe closed at one end is equal to the third harmonic of a pipe open at both ends. How are the lengths of the two pipes related?
A.
B.
B. /!>/ C / = /i
D. / and f\ are unrelated.
23.
A. B. C. D.
traveling transverse waves. standing traveling waves. traveling longitudinal waves. standing longitudinal waves.
25. A surgical use for sound waves is to destroy gallstones with the vibrations. Two ways to measure the loudness
6=KMog10 [where I0 is a reference intensity. Ultrasonic surgical tools operate at 170 decibels, whereas imagers operate
at 150 decibels. How much more or less intense are the
C.
1.
2. 7.
C D
3. A
5.
10. D 15. B
20.
12. C
17. C
22. D
25.
27
Violin Strings
Choice C is the best answer. If the length of a typical violin string is 30 cm, what are the wavelengths of the first three
harmonics? In the passage, we were given the formula for the frequencies, which is: / = nv/2L- Usin8 tne 8olden ru,e for
waves, v=fX, we can solve for the wavelengths: X=VU. We find that: vlf =2L/n, so the wavelengths are given by: X=
2L/n. Plugging in values for Land ngives:
Xi=2(30cm)=60cm
The best answer is choice C.
2(30cmi=30cm
2
X3=2(30cm)=20cm
3
Choice C is the best answer. What is the fundamental pitch of a string that has a length of 30 cm, a mass of 30 g, and a tension of 9000 N? To start, pitch is just the perceptual correlate of what a physicist calls "frequency." Using the frequency
formula in the passage, / = nv/2L we can plug in the fundamental pitch value n = 1 and the length value of 0.3 m after we
calculate the speed v. To calculate that, we have to use the other formula given in the passage:
_ JTL _
(9000)(.30)
V .03
Now that we know the speed, we can calculate the fundamental pitch, where n is equal to one:
2(0.3) m
Choice A is the best answer. What happens to the pitch (frequency) of a standing wave on a violin string when the tension on that string is changed? To answer that question, we must combine the two formulas given in the passage:
/ = nv and v 2L
T-L M
/= ,
I^= n
M 2
.-. / Vf
2L
M-L
We can see from the formula that as the tension increases, the frequency must also increase. Notice that choices B and C give the same relationship between/and T, invalidating both of them. The best answer is choice A.
Choice A is the best answer. Violin players can press down on the violin strings effectively to shorten the length of a particular string. What happens to the frequency and wavelength of the standing waves when this occurs? According to the
rule for waves, X= vle. As/increases, Xmust decrease and vice versa. Since frequency is proportional to V^, decreasing
length means increasing frequency. Since the frequency is increasing, the wavelength must be decreasing. The best answer
is choice A.
Choice B is the best answer. What change would double the fundamental frequency produced by a violin string? All of our answer choices involve changing the string tension, which means we need to know how frequency depends on tension. To get this relation, we must combine the two formulas given in the passage. The result is:
T-L
/ Vf"
2L
In order to double the frequency, we must quadruple the tension. The best answer is choice B. Choice C is the best answer. Two strings have the same length and fundamental wavelength, but different fundamental frequencies. How is this possible? The wavelengths are given by X = 2L/n. The wavelengths are affected only by the length
VT'L M
is the same for both strings, a different T or a different M must be creating different frequencies, which is choice C. The mounting angle of the string will have no bearing on the frequency, according to the equation. The mounting angle would simply affect the ability of the string to be displaced. The best answer is choice C.
28
MINI-TEST EXPLANATIONS
7.
Choice D is the best answer. Whether it's standing waves produced on a violin string or sound waves produced by that
string, sound waves are longitudinal. As part of your general physics knowledge, you should know that sound waves are longitudinal. This was alluded to in the first paragraph of the passage. Based on this, we can eliminate choices A and C. You
should also know that standing waves on strings are transverse. The best answer is choice D.
Train Whistle
Choice A is the best answer. If the train is in the station and blows Whistle 1 with frequency f\ = 440 Hz, what is the wavelength of the emitted sound?This is a straightforward application of v = fX, where v is 330 m/s, and / is 440 Hz. This
means that: >. = (330 m/s)/(440 Hz) = 0.75 m. If you remembered the proper equation, v = fX, which you should have
memorized, you should have noticed that the wavelength had to be less than 1 m. The only two choices less than 1 m were
choices A and D. The best answer is choice A.
9.
Choice D is the best answer. Suppose f\ = 440 Hz and fi = 450 Hz. If both whistles are blown at the same time while the
rain is in the station, what is the beat frequency? The beat frequency is given by /b = I/] - ft\. This means that/b = I440 Hz - 450 Hz I, which is 10 Hz. The equation for the beat frequency is another equation that should be tucked away in your
memory. Choice A, 445 Hz, is the average frequency. Choice B, 890 Hz, is the sum of the two frequencies. Choice C, - 10
Hz, is not possible, because frequency is by definition a positive quantity. The best answer is choice D.
10.
Choice D is the best answer. Sound wave A has an amplitude of 1 mm, and Sound wave B has an amplitude of 3 mm. What are the maximum and minimum possible amplitudes, if A and B interfere? If A and B are in phase when they interfere, their amplitudes will sum to give the maximum amplitude. If A and B are 180 out of phase when they interfere, their amplitudes
will cancel each other out.
=>
A + B B-A
4 mm 2 mm
W
A and B interfering in-phase
When we subtract the amplitudes, the result must be positive, because amplitude is by definition a positive quantity. Based on that, choices B and C are eliminated. The math gives: Max = 3 mm + 1 mm = 4 mm, and Min = 3 mm - 1 mm = 2 mm.
The best answer is choice D. 11.
Choice A is the best answer. Whistle 1 has an intensity twice that of Whistle 2. Whistle 1 has an intensity level that is how many dB greater than the intensity level of Whistle 2? The intensity level is given by:
B=10-log10
(l\
Let's say the intensity of Whistle 2 is I, which means the intensity of Whistle 1 is 21. The intensity level of Whistle 1 is:
6=10-log10 pi*o/
=>
B=10-logI0W+ 10-logI0(2)
v*o/
The first term is the intensity of Whistle 2. So Whistle 1 is 10 log 2 decibels greater than Whistle 2. Log 2 is 0.3, so Whistle 1 is about 3 decibels louder than Whistle 2. To increase the intensity level by +10dB, the intensity must be increased by a
factor of 10! The best answer is choice A.
12.
Choice C is the best answer. As the train approaches a station, it blows both whistles. A person standing on the platform hears both whistles with apparent frequencies f\' and ft. How are the frequencies related? When the train is approaching the station, the perceived frequencies heard by the listener are greater than the actual frequencies at the sound source because of a Doppler shift. We can definitely conclude that f\ < f\' and f2 < ft, which is choice C. Choice A is not the best answer, because we cannot say for sure that J2 < /l'- Choice B is not the best answer, because we can't say for sure that /2 > /]'. Choice D is incorrect, because /2 < ft, not J2 > ft- The best answer is choice C.
Choice B is the best answer. If the train's whistles are treated as pipes that are open at one end and closed at the other, which could be a picture of the air column in one pipe, if it is oscillating in its fundamental mode? When a pipe is open at one end, that means the particle displacement must be at a maximum at that end. When a pipe is closed at one end, that means the particle displacement must be at a minimum at that end. The only picture among the answer choices that has a maximum at the open end and a minimum at the closed end is choice B. The best answer is choice B.
29 MINI-TEST EXPLANATIONS
13.
14.
Choice C is the best answer. The engineer blows Whistle 1 when the train is 660 m away from the tunnel (see diagram
below). How much time elapses between the moment when the whistle is blown and the moment when its echo is heard by the engineer? If the train were stationary, the sound of the whistle would take 2 seconds to reach the tunnel (660 maway),
and the echo would take another 2 seconds to return to the engineer (assuming that the speed of sound in air is 330 m/s). The total time for the initial sound wave of the echo to reach the ear of the engineer sitting in a stationary train would be 4 seconds. But the train is not stationary. It is moving towards the tunnel at 20 m/s. Therefore, we can quickly figure out that
the echo will require fewer than 4 seconds but more than 2 seconds to reach the engineer. This allows us to eliminate choices
A and D.
Where will the train be when the sound of the whistle reaches the tunnel? Remember that the sound waves takes 2 seconds to
reach the tunnel, during which time the train travels (20 m/s x 2 s) or 40 m, placing it at a position 620 m from the opening of the tunnel. The echo 1 second later will be 330 m away from the tunnel and approaching the oncoming train. The train will be 20 m closer to the tunnel (i.e., 600 m away from the tunnel). The echo and the engineer are still 270 m apart from one another-and exactly 3 seconds have elapsed. The echo time must be greater than 3 s, which allows us to eliminate choice B
and select choice C as the best answer.
The problem is also solved using algebra. When the echo and the engineer meet: (dwave - 660 m) + dlrain = 660 m, and: dwave = vwave 'l > ^train = vtrain ** If vve let x eclua' tne l'me elaPsed untiI tne whistle is heard by the approaching
engineer, then: (330 m/s x) - 660 m + (20 m/s x) = 600 m. Solving for x, vve get:
x = '320 m = 377 s
350 m/s
While the algebraic answer may offer some reassurance that our intuition was correct, there is just not enough time to do this math during the MCAT. As you prepare for your MCAT, be sure to emphasize visualization and intuition when determining
the best answers to your questions. The best answer is choice C.
Submarine Sonar
Choice B is the best answer. Four seconds is the total time it takes for the signal to leave the submarine, hit the ocean floor,
Be wary of questions where the time for a round-trip is given. A standard trick question involves asking for one-way distance
after giving you the round-trip time. The best answer is choice B.
16.
Choice B is the best answer. Because the target for the bat is considerably smaller than for a submarine, the wavelength must be shorter for the bat's radar signal than the submarine's sonar signal. The wavelength of the signal must be roughly equal in size to or shorter than the object. Regarding the higher or lower frequency, remember that the frequency will also
depend upon the wave speed, which is considerably different for the sub's waterborne sonar and the bat's airborne sonar. The
best answer is choice B.
17.
Choice C is the best answer. The speed of sound is greater in water (the denser medium) than in air. 1500 m/s is roughly 3000 miles per hour. Mach I (the speed of sound in air) is just above 700 miles per hour. This makes statement I true. According to the equation, when the object moves away from the observer, the frequency decreases, so statement II is false. The speed of any wave depends on its wavelength and frequency. Specifically, v = fX requires that wave speed increase, if the wavelength is to increase and the frequency is to remain fixed. This makes statement III valid. Choice C is the best
answer. Notice that statement I is part of every choice, so you do not need to spend time considering that statement. The best
answer is choice C.
30
MINI-TEST EXPLANATIONS
18.
Choice Dis the best answer. There are two methods ofsolving this problem. Method #1: Plug the numbers into the Doppler
formula, noting that v0 = vb = +20 m/s (+ because the observer moves towards the source) and v$ = v^ =0 m/s.
Method #2: Understand the physics and eliminate the impossible answers. The physics: When an observer approaches the
source, the observer must measure a frequency f\ greater than the original frequency /. The impossible answers: 491 Hz and
496 Hz. The only answer significantly greater than 500 Hz is choice D, 507 Hz. The best answer is choice D.
19.
Choice A is the best answer. Submarine USA emits the signal with frequency / = 500 Hz. The active sonar source measures
the frequency to be:
The active sonar source is now the source of the echo sent back to Submarine USA. The echo will undergo a second Doppler
h =f1(*) =503 Hz V - Vc
1500 m/s
507 Hz
The standard emitted pulse is shifted only once: /echo > /source- The most difficult part of this problem is realizing that we must apply the Doppler shift twice, with Submarine USA and the stationary source exchanging roles as source and observer after the first Doppler shift. The best answer is choice A.
20. Choice C is the best answer. The lowest frequency, according to the equation, is observed when the source and the observer are moving away from each other at the greatest relative speed. In choices A and B, the two submarines are moving towards each other, so in each case the Doppler shift will result in frequencies greater than 500 Hz. In choice D, the distance between the two submarines is increasing (reducing the frequency), but the distance between the submarines does not increase at the
same rate as it does in choice C. Choice C is best.
500 Hz f1500 m/s + 10 m/s\ >^qq j_jz [1500 m/s + 10 m/s\ >*jqq ^z /
\ 1500 m/s - 20 m/s/
The best answer is choice C. 21.
1500 m/s
Choice C is the best answer. The Doppler shift depends on whether there is relative motion between the source and the observer. Since both submarines are moving in the same direction with the same speed, there is no relative motion between them. Thus, there is no Doppler shift; f\=f. Using the Doppler formula: _ffv-vo\_f/i500 m/s- lOm/s = f _ = f fl=f
v - Vc
Since the observer is trying to move away from the source, you must choose the minus sign for v0. Since the source is trying to move towards the observer, you must choose the minus sign for vs. The best answer is choice C.
Questions 22 - 25
22.
Choice D is the best answer. For a pipe that is open at one end and closed at the other end, the possible frequencies are:
For a pipe that is open at both ends, the possible frequencies are:
In the case where the pipe is closed at one end, n can only be an odd integer. The fundamental frequency occurs when n = 1. For a pipe open at both ends, n can be any integer. The third harmonic occurs when n = 3. Setting these two equations equal
to each other, we solve for the relationship between the lengths of the pipes:
v _ 3v
4 Lclosed
choice D.
2 L0pen
Note that the wave speed is the same for both pipes, since the waves produced are sound waves in air. The best answer is
31
MINI-TEST EXPLANATIONS
23.
Choice Cis the best answer. If you are aware that sonification uses sound waves, then you can easily answer this knowing that sound is alongitudinal wave that travels. Otherwise, we need to analyze each choice. Transverse waves cannot travel in
simple fluids, so choice Ais incorrect and thereby eliminated. Awave is either traveling or standing, but not both. This
allows us to eliminate choice B immediately. Traveling waves are those waves where the wave pattern moves through the medium. This is what happens to a sound wave sent out by a sonification source. Standing waves are formed by the interference oftwo traveling waves, traveling in opposite directions, usually because of boundary conditions. Sonification
answer is choice C.
employs sound waves traveling through mediums, so choice Cis the best answer and choice Dis eliminated. The best
Choice B isthebest answer. Just like sound intensity, the speed ofsound also increases asa medium becomes denser. If we
24.
are looking for the medium in which the speed of sound is the slowest, we would be looking for the medium with the least density. The medium ofleast density might at first appear to be avacuum (zero density); but avacuum is the absence of any
medium. Sound waves need a medium in order to propagate, because sound is transferred via molecular vibrations and
collisions. After eliminating choice A(avacuum), we should then notice that air is the least dense ofthe remaining materials.
The best answer is choice B.
25.
Choice B is correct. This question tests your skills with logarithms more than your skill with conceptual physics. The
formula you are to decipher is:
B=KMog10(
We are told the intensities in decibels (dB) and are asked to find the intensities in W/m2.1 is in W/m2, and Bis in dB. We are basically being asked tosolve for I. Recall the rules for logs: x= log y means y = 10*.
i=i0-io(b/io)
Now, if we want to find a ratio of intensities in W/m2, we just plug the given values into the equation. For the imager, we
have:
li
Io1015
Notice that IQ dropped out of the equation. Try to avoid plugging in values for variables in a problem. The variable may just drop out, saving you time and helping you avoid an error. The best answer is choice B.
32
MINI-TEST EXPLANATIONS
Sound Intensity
Propagation of Sound
Bat Echolocation
(1-6) (7 -11)
Sound Experiment
Jet Radar
Organ Pipes
Sound Resonance
(43 - 48)
(49 - 52)
Passage I (Questions 1 - 6)
3.
C.
5000 Hz
D. Sound waves of frequencies 200 Hz, 1000 Hz, and 5000 Hz move at the same speed through water.
various readings. Already knowing that the intensity of sound waves in a liquid is higher than in a gas, the experimenters were trying to confirm that Equation 1 accurately describes
the intensity of sound waves in a liquid.
Equation 1
I=i/pBo)2A2
2
4.
As we move away from the source of a sound wave, from a distance r to a distance 3r, the intensity of that
wave:
In addition to testing the intensity of the sound waves at different points, the study was also meant to measure the penetration depth of different frequencies. A commonly accepted theory is that although sound is observed as a wave phenomenon, it also has particle properties. Drawing a
parallel to light theory, vve know that light can be broken down into corpuscles called photons. Similarly, it is believed
that sound can be broken down into small units called
phonons. According to this theory, a single phonon has an energy given by Equation 2, where h is Planck's constant
Ephonon - "f
5.
A phonon is the smallest amount of energy that can be carried by a sound of a particular frequency. The reason we do not notice this quantization in life is because the amount of energy of one phonon is minuscule, and it would be quite difficult to isolate its energy.
1.
If all of the frequencies in this experiment were emitted at the same time into air along with a frequency of 1010 Hz, which of the following frequencies would also be
detected?
A.
B.
10 Hz
810 Hz
C.
3990 Hz
D.
a vacuum.
air.
C.
water.
6.
D. mercury.
In a simple liquid thicker than air, a sound wave of a fixed frequency is:
B. longitudinal with ^.Medium < ^AirC. transverse with A-Medium > ^AirD. transverse with ^.Medium < ^Air-
A. B. C. D.
34
8.
governed by the laws of wave motion. One of these laws is that the speed of a wave, v, is related to the sound wave's frequency and wavelength by: v = Xf
Another law of wave motion deals with how sound
B.
C.
waves reflect when they hit an interface between two different media. The ratio of the reflected wave's intensity to the incident wave's intensity is given by:
^reflected _
incident
9.
Plvl-P2v2\2
Plvl + P2v2/
Which list of numbers represents the respective times it takes for a sound wave to travel through 5 cm of air,
water, and flesh?
where pi and p2 are the respective densities of the incident and reflecting media, and vj and V2 are the respective speeds of the sound waves in the two media. Typically, waves will reflect more if pi < p2 or if P2 < pi, than if pi is approximately equal to p2Sound waves come in a variety of frequencies, each frequency range having a different degree of importance in our lives. For instance, the frequency range between approximately 20 Hz and 20,000 Hz is where human beings
detect sounds.
A. B. C. D.
1.5 x 10-4 sec,3.4 x 10'5 sec, 3.2 x 10"5 sec. 3.2 x 10"5 sec,3.4 x 10"5 sec, 1.5 x 10"4 sec. 1.5 x 10"1 sec,3.4 x 10"2 sec, 3.2 x 10"2 sec. 3.4 x 10"5 sec,3.4 x 10"5 sec, 3.4 x 10-5 sec.
10.
Above 20,000 Hz, our ears fail us. However, this does
that these sounds are useless. People use these sounds in the medical field daily. They allow "see" into the bodies of patients, where X-rays useless and/or dangerous. The theory behind
line of the brain. Two oscilloscope traces show time versus sound intensity in the detector, when the detector is placed on the left side of a patient's head and on the right side of a patient's head.
detector on left side
ultrasound imaging is this: Send a sound pulse into the body and measure how long it takes for a reflected pulse to return.
k
C.
il
A. that the left side of the brain was larger than the right side of the brain. B. that the right side of the brain was larger than the
left side of the brain. that both sides of the brain were the same size.
p (kg/m3)
1.05 1000
1047
v (m/s)
344 1480 1570
Flesh
Table 1
7.
11.
About 1 mm
About 1 cm
C. D.
D.
.001570 m
35
15.
When a wave travels from air into water, its speed increases by a factor of four. Compared to the wave in
air, the transmitted wave has:
for example, reflect off nearby insects and return to the animal. The elapsed time of these echoes allows the bat to
determine the distance to its food.
A. B. C. D.
the same frequency, but a longer wavelength. the same frequency, but a shorter wavelength. the same wavelength, but a higher frequency. the same wavelength, but a lower frequency.
frequency of the emitted sound. The relationship between the reflected frequency fr and the emitted frequency fe is
shown in Equation 1.
_(v +vt) f
Equation 1
16.
All of the following play a role in echolocation when determining position and speed of an object EXCEPT:
when the target is moving at a speed vt relative to the bat. Here, v, > 0 means that the bat and target are approaching each other; v is the speed of sound. (Unless otherwise stated, the speed of sound is 340 m/s.)
12. A bug and a bat are initially 17 m apart, when the bat emits a sonic chirp. The creatures approach each other at a relative speed of 0.5 m/s. How long after emitting the chirp does the bat hear its reflection?
A.
B.
C. the speed of the object D. a difference in wavelength between the emitted and
reflected waves.
0.0498 second
0.0502 second
17. The HIGHEST reflected frequency is observed with a: A. stationary bat and a bug flying towards it B. stationary bat and a bug flying away from it. C. bat flying towards a bug that is flying away from
the bat
C.
D.
0.0999 second
0.1001 second
bat
B.
C. D.
12 dB
19 dB 25 dB
A. B. C. D.
122.2% of the emitted frequency. 100.2% of the emitted frequency. 99.8% of the emitted frequency. 81.8% of the emitted frequency.
36
21. Which of the following graphs BEST represents the frequency of a sound wave emitted from a closed pipe
as a function of the length of the pipe?
A. B.
18.
For a sound wave traveling through air at room temperature and pressure, which plot BEST represents the relation between the wave's frequency and its speed?
A. B.
Length (L)
8.
C.
Length (L)
20
20,000
20
20,000
Frequency (Hz)
C.
D.
Frequency (Hz)
o c
i"
Length (L)
Length (L)
8.
20
20,000
20
20,000
Frequency (Hz)
Frequency (Hz)
19.
Which relationship BEST relates the pitch of the siren for an ambulance relative to a stationary observer?
A. B. C D.
/approaching > /stationary > /leaving /leaving >* /stationary > /approaching /stationary > /approaching > /leaving /stationary > /leaving > /approaching
20.
Two cars have identical horns with a frequency of 400 Hz. Which situation will NOT generate a beat frequency when both cars simultaneously honk their
horns?
A. Car I is stationary; car II is moving left at 20 m/s. B. Car I moving right at 20 m/s; car II is stationary. C. Car I moving left at 20 m/s; car II is moving right
at 20 m/s.
37
23. How would the experiment need to be changed, if one desires to produce the same frequencies as those
measured in the experiment, but when the room
In an experiment to demonstrate how resonances work, physics students gather five tuning forks of frequencies 1020
Hz, 850 Hz, 680 Hz, 510 Hz, and 340 Hz. The students also
have a glass tube of length 1 m and diameter 8 cm. The glass tube is placed on a table and completely filled with water. Starting with the tuning fork with the highest frequency, each tuning fork is struck and placed over the open end of the
water-filled tube, as in Figure 1. While each tuning fork is held over the tube, the water level is slowly lowered until a
loud resonance is heard. Once the resonance is heard, the water height is recorded.
Tuning
fork
C. The water height would need to be lowered. D. The water height would need to be raised.
24.
How does the speed of sound in Trial 5, V5, compare with the speed of sound in Trial 3, V3? A. V5 = 2V3
Ti be
hei ght
Water
1
h
>
B. v5 = V2v3
C. v5 = v3
height
D. V5 = ^v3
25. The experiment will NOT work, if the tube space above
the water is filled with:
Figure 1. Experimental Apparatus Theoretically, resonance should occur whenever the following condition is met:
f _ nv
4L
A. B.
0Cair. 0C ice.
C. D.
where n = 1,3,5,..., f is the frequency of the tuning fork, v is the speed of sound in air, and L is the length of the air
column. The students also measure the fundamental mode, n
26.
In Trial 5, the height of the water was 75.0 cm. The tuning fork from which other trial could be used to produce a resonance for a water height of 75.0 cm?
A. B. Trial 1 Trial 2
Frequency (Hz)
1020 850
680
C.
D.
Trial 3
Trial 4
4 5
27.
Suppose the tuning fork in Trial 4 were measured to have an intensity level of 50 dB. If a second, identical tuning fork were struck and brought near the first fork, together they would have an intensity level of:
A. B. C. D. 50 dB. 53 dB. 60 dB. 100 dB.
temperature of 20 C. 22. What is the wavelength of sound produced by the tuning fork in Trial 3?
A. B. 87.5 cm 50.0 cm
C.
D.
25.0 cm
12.5 cm
38
29.
In the landing of jets, radar systems are employed to track and analyze the jet's pathway. In earlier years, this was
accomplished when the jet emitted a radio signal of the same frequency as a stationary beacon positioned at some distance from the runway. The motion of the jet affects the frequency of the emitted signal, according to the Doppler equation:
Equation 1
v vs
B. No, because longitudinal waves need a medium. C. Yes, because electromagnetic waves do not need a
medium.
In Equation 1, ft is the frequency received by the listener, /s is the frequency emitted by the sender, v is the velocity of the transmitted wave, vl is the velocity of the listener, and vs is the velocity of the source. The varies
with the direction of the motion of the source and listener.
30. Radar guns emit radio waves. The radar gun measures the beat frequency between the returning waves. How
does the radar gun determine velocity? A. By measuring the beat frequency between two
consecutive reflected waves.
difference in frequency between the jet's emitted signal and the beacon's emitted signal can be used to determine the velocity of the jet. The difference in frequency between the two signals is known as the beat frequency. This is given in
Equation 2:
Equation 2 /beat ='/1-/2'
B. By measuring the beat frequency between a wave reflected from a stationary object and one reflected
from a moving object.
C. By measuring the beat frequency between a wave reflected from two separate objects moving at the
same speed.
In Equation 2, /beat is me Deat frequency, f\ is the frequency of Wave 1, and /2 is the frequency of Wave 2. Combining the two equations for the airport scenario, with a moving emitter and a stationary emitter, the beat frequency for the jet signal and beacon signal is given in Equation 3: Equation 3
D. By measuring the beat frequency between a wave reflected from two separate objects moving at different speeds.
/b eat
/l
31.
Using radar, for which object would it be hardest to evaluate its velocity?
A. B. C. D. A moving train A moving car A flying bird A flying insect
where f\ is the frequency of the beacon's and jet's emitted wave, without accounting for Doppler-shifting. Modern systems employ radar sent out and the reflected signals frequency is obtained when one stationary object, while the other moving object. guns, where a signal is are analyzed. The beat wave reflects off of a wave reflects off of a
28. When using active radar, where radio waves are emitted from the same point at which the reflected waves are detected, all of the following should be considered
EXCEPT:
32.
How can the frequency shift of a radio wave reflected off of a moving object be determined?
A. A/ = /0(v)
B. A/ = /0(c) C. A/ = /0(v/c)
D. A/ = /0(2v/c)
B. a stationary reference beam is needed. C. the gun operates when stationary and in motion. D. the best electromagnetic radiation is in the ultraviolet range.
39
36.
B. longitudinal. C. either transverse or longitudinal, depending on the air temperature. D. either transverse or longitudinal, depending on the
altitude.
34.
to return. Could such a depth finder distinguish between the following three things?
I. A rocky sea floor
II. A rocky sea floor, covered with a watery silt III. A school of fish, swimming near the bottom A. I and II can be distinguished from III, but not from
each other.
40
Passage VI (Questions 37 - 42) Some organ pipes are open at both ends, while others are open at one end and closed at the other. They amplify selected frequencies (harmonics) based on the dimensions of the pipe and speed of the wave. An open pipe is illustrated in Figure 1 below.
39. To most effectively increase the frequency in the pipe, one should replace the N2 in the air with:
A. He, and lengthen the pipe. B. H2, and lengthen the pipe. C. He, and shorten the pipe. D. H2, and shorten the pipe.
^< lip
air in-
=r
40. If you increase the temperature of the air by 44%, the speed of the sound wave increases by:
Figure 1
A. B. 6.6% 20%
They emit sound when air is blown around a lip near one end. This air turbulently enters one end of the pipe, and can cause air in the pipe to resonate at various frequencies. These frequenciesare given by Equation 1.
f _ nv
C. D.
44% 107%
Equation 1
41. For an open pipe that is 15 cm long, what is the frequency associated with the third harmonic, assuming the speed of sound in air is 340 m/s?
A. B. 3.4 Hz 34 Hz
C.
D.
340 Hz
3400 Hz
B. that /n = n(/0), when n is the harmonic number and /0 is the fundamental frequency of the pipe. C. that X.n = n(XQ), when n is the harmonic number and Xq is the fundamental wavelength of the pipe.
D. the length of a pipe impacts the harmonics more
than the diameter of the pipe.
42. The frequency spectrum of one organ pipe is measured and plotted below. (The dominant frequencies and zero
are enumerated.) What is the pipe's length?
dB
lllll I
T
.1.
255 Hz
85
A. 0.3 meter
170
B.
0.5 meter
1.0 meter 2.0 meter
38. Two pipes with identical dimensions differ only at their ends: pipe #1 is open on both ends and pipe #2 is open only on one end. What is the ratio of the fundamental frequency of pipe #1 to that of pipe #2?
A.
B.
C. D.
2:1
3:2
C. D.
2:3 1:2
41
45. A pipe open at both ends produces a frequency of 440 Hz. A string tied a both ends vibrates with a frequency of 430 Hz. Which of the following statements is true?
A. The two waves will never produce a beat frequency, since the waves come from different
sources.
students performed a set of experiments using strings and pipes of different lengths. All of the strings were tied down
at both ends. Some of the pipes were open at both ends, while some of the pipes were closed at one end and open at the other end. To generate waves on the strings, the strings were attached to a mechanical wave generator. Waves in the pipes were generated by means of different tuning forks. The forks and pipes were arranged so that they were parallel to
one another.
C. A beat frequency of 10 Hz will be produced. D. The two waves will exhibit almost completely
destructive interference.
For strings that are tied down at both ends and for pipes that are open at both ends, the possible frequencies for
vibration are:
/= nv;n = l, 2,3,...
2L
For pipes that are closed at one end, the possible frequencies for vibration are: /=nv;n = 1,3,5,...
4L
C. They produce waves with the equal frequencies. D. Not enough information given.
In all cases, v is used to represent wave speed and L is used to represent the pipe length.
47. How could thestudents generate a wave on a string that had the same shape as the wave generated in a pipe
closed at one end?
C. The waves could be identical when the string is tied at both ends, and the string is the same length
as the pipe.
D. The waves could be identical when the string is tied at both ends, and the string is twice the length
of the pipe.
44. If the temperature of the room changes from 30C to 33C, which of the following statements is true? (Ignore any thermal expansion of the pipe and string.)
A. The pitch of the wave produced by the string changes; the pitch of the wave produced by the
pipe does not.
B. The pitch of the wave produced in the pipe changes; the pitch of the wave produced by the
string does not.
A. wavescould be produced in the pipes. B. wavescould be produced on the strings. C. waves could be produced in the pipes and on the
strings.
C. The pitch of both waves changes. D. The pitch of neither wave changes.
42
52. A 450 Hz tuning fork shows a beat frequency of 12 Hz with another tuning fork. The other tuning fork has:
A. B. C. D. no definite frequency. a frequency of 438 Hz and 462 Hz. a frequency of 444 Hz or 456 Hz. a frequency of 438 Hz or 462 Hz.
49.
A. 40 times farther away. B. 160 times farther away. C. 316 times farther away. D. 10,000 times farther away.
50.
A bat uses a sonic chirp to echolocate nearby small insects in the hopes of feeding upon them. What would be the effect of putting a piece of glass between a bat and its prey? The bat would:
A. not perceive a difference in the prey's location. B. perceive the prey as farther away. C. perceive the prey as closer.
D. detect a reflection of itself.
51. When sound initially traveling from a source on the left strikes the following barriers and echoes back, what is
observed for the various echoes?
ha*+
Air Ro( Water
Echo I
AAAA/1mmmm
Ef-;\
Echo II
vAAA/fclK
1. D
7. C 13. C 19. A 2. A
3. D 9. A
4.
5. D
11. B 17. D 23. C
6.
8. 14.
20.
C
B
D
10. 16.
22.
B B
B
12.
15. A
21. C
18. D
24.
C B
25. C 31. D
37. C
43. A
26.
32.
27. B
28.
30.
D
A
B
33. A
39. D
45. C
34. A
40.
36.
42.
48.
B D
B
B
D
46.
49. C
51. D
52. D
43
Choice A is the best answer. Sound waves are always longitudinal waves, so choices C and D can be eliminated immediately. When sound (longitudinal) waves enter a medium that has a larger bulk modulus, the velocity of these waves increases. If you recall the wave equation v = Xf, then you know that as the velocity of a wave increases, so does its
wavelength, assuming that frequency is constant. Both the speed and the wavelength of sound waves must be greater in the
liquid than in air. The best answer is choice A.
Choice D is the best answer. Although one frequency may penetrate farther into a medium than another, sound waves of all
frequencies move at the same speed in a given medium. For this reason, sound waves of all of the frequencies mentioned in
the question move at the same speed in water. The best answer is choice D.
Choice B is the best answer. The intensity of a sound wave decreases as the inverse squareof its distance from the source.
Looking at the equation I = P/A = P/4jrr2, you should be able to deduce that as the radius increases by a factor of 3, the
intensity decreases by a factor of 9. The best answer is choice B.
Choice D is the best answer. If a frequency of 1010 Hz were also emitted, all of the frequencies mentioned would be beat
frequencies: /Beat = l/l - ft- Typically, beat frequency problems discuss only waves of nearby frequency, which may have led you to pick choice A. A beat is just an interference effect between two waves, regardless of their frequency. The best
answer is choice D.
Choice Cis the best answer. 7.5 x 10"30 Jof sound energy could not be measured in asound wave of 1500 Hz if the energy of one phonon were 1.0 x lO'30 J, because 7.5 x 10"30 J is not a whole number multiple of 1.0 x 10"30 J. All of the other
amounts of energy are whole number multiples of the energy of one phonon, 1.0 x 10"30 J and thus could be measured in a sound wave of 1500 Hz if the appropriate number of phonons were present. For instance, choice B is possible, because five
1500 Hz phonons collectively could sum to 5.0 x 10"30 J, making choice B a viable amount of total energy. The best
answer is choice C.
Propagation of Sound
Choice C is the best answer. Let's consider what is happening when a sound wave, incident in some Medium 1, reflects off
'incident ) J
Medium 1
Medium 2
'refelcted
-* ci
((
We hear the echo after the reflected wave returns to the incident wave's starting point. By the time t has elapsed, the waves
have traveled a distance 2d at some speed v. We are told v = 1570 m/s (for flesh), and t = 10"5 s. We are solving for d in an
equation that reads: "total distance = speed x time." This is 2d = vt. Solving for d yields:
The answer has to be less than .0157 m (choice A), so rule it out. The only possible remaining choices are C and D, but
choice D is .00157 (a factor of 10 smaller the .0157). Thus, choice D is also eliminated. The best answer is choice C.
44
8.
Choice C is the best answer. In the passage, we are told that sound (incident in a Medium 1) will not reflect much from
Medium 2, if the densities of the two media are close in value to each other:
magnitudes of the numbers are wrong. For example, it should take very little time for sound to travel 5 cm in air. This choice
says that it takes 1.5 x 10"1 sec. If that were true, it would take around 1 second for sound to travel 1 m. That violates
physical intuition. Thus, rule out choice C. We could have multiplied out all of the numbers, but it takes a longer time than using physical intuition. The best answer is choice A.
10. Choice B is the best answer. The oscilloscope traces look like this:
I detector on left side
h
hemisphere. The best answer is choice B.
11.
The detector on the left side of the head: We see the midline echoafter a short time. If the midline echo were in the middle of the plot (i.e., halfof the time to hear the "right side of the skull echo"), then the midline would be in the middle of the head.
But since we see the echo sooner than that, the midline must be closer to the left side of the skull than to the right side.
The detector on the right side of the head: This plot confirms our suspicions about the first plot. Since vve see the midline echo at a fairly late time in this plot, it must mean than the midline is farther from the right side than it is from the left side. The conclusion is that the patient has brain hemispheres of unequal size, the right hemisphere being larger than the left
Choice B is correct. To understand this answer, let's see how a wave behaves when it hits some object. Here are two cases:
a boat being hit by waves, where the wavelength of the waves is smaller than the size of the boat; and a buoy being hit by the
same waves, where the buoy size is smaller than the wavelength of the waves.
waves
buoy
boat's shadow
Od>X 6<X
buoy's
shadow
Notice how you can see a "shadow" of the boat in the water, but you cannot see much of a "shadow" for the buoy. This behavior applies to all waves: water, sound, or light. Ultrasonic waves do not allow you to see objects that are smaller than the wavelength of the sound, which is found using the equation v = fX. Thus, X= \/f. Bysubstitution, we get:
X =
0.01 m=
1 cm
Using the math works fine here. However, we could have eliminated some of the answers without math. Choice D is invalid.
It states that there is no limit to what the ultrasound at 157,000 Hz can "see." If that were true, you could see individual
atoms with your eyes. Your eyes see light with wavelengths of around 10"7 m, and atoms are about 10"10 min size.
Choice C is incorrect. It says that this typical ultrasound device cannot resolve anything with a diameter less than 1 m. If this
were true, then ultrasound devices at this frequency would be useless. The best answer is choice B.
45
Bat Echolocation
12. Choice C is the best answer. Let's find the approximate time by assuming the bat and bug are not moving. We ignore their motion, because incorporating it into a calculation is hard, and because their slow motion (relative to the sound speed) won't affect our answer much. Using Decho travels = Vsoundtecho travels- and noting that Dech0 travels = 2(17 m) = 34 m gives an echo
time of 0.1 sec. The actual time should be slightly shorter because the two creatures are approaching one another. This is
choice C. If you forgot that the echoing sound must travel to the bug and back, you probably picked choice A. The best
answer is choice C.
13. Choice C is the best answer. When doubling the distance r from an isotropic sound source, the intensity / becomes 74 as
strong because / 7r2. However, the intensity level, fi, does not drop by this amount. Because intensity should drop, choice
D is incorrect. To figure out the amount by which fi drops, recall that dividing the intensity by 10 is equivalent to subtracting
10 from the intensity level. If / became /io,h as its original value, fi would be 25dB - lOdB = 15dB. Since / doesn't drop
quite that much,fi should be larger than 15dB. This points to choice C. If you want to be a little more quantitative, we know the intensity drops by a factor of four. Decibels are measured on a log scale, and log 4 is 0.6, which means 10 (log 4) = 6. The
intensity should drop by 6dB, resulting in an intensity of 19dB. The best answer is choice C.
14. Choice B is the best answer. Since the bug and bat approach each other, the reflected frequency should exceed the emitted frequency. This rules out choices C and D. Since the bug speed is very small compared to the speed of sound, the increase in
the reflected frequency should be very small. This points to choice B. The math is as follows:
15. Choice A is the best answer. When arw. wave travels from one medium into another, its frequency remains the same. The only case where the frequency of the wave changes is when the sender or receiver are moving relative to one another, which is not the case here. This rules outchoices C and D. Since v =/A, an increased speed v means an increased wavelength A(when/
is fixed). The best answer is choice A.
16. Choice B is the best answer. Echolocation, as described in the passage for a bat, involves analyzing the reflected wave for frequency shifts and echo time. Because the wave reflects off a moving target, it experiences a Doppler shift. This means that
the frequency and wavelength are varied. This eliminates choices A and D. The target must be in motion relative to the analyzer, so the speed of the object definitely plays a role. This eliminates choice C. The only thing that does not occur is a shift in the wave speed. That is observed when the medium changes, which is not the case in echolocation for a bat (which
remains in the air during the process). In reality, because temperature fluctuates in fluid mediums, wave speeds do change as they pass through thermal pockets within a medium. However, that is not described in the echolocation procedure used by a
bat. The best answer is choice B.
17. Choice D is the best answer. The highest reflected frequency results from the largest Doppler shift. The Doppler shift is
greatest when the objects are moving towards one another at the highest possible speed. This eliminates choices A and B. In choice D, the two creatures are flying towards one another, so their separation distance is decreasing faster than in choice C,
where they are flying in the same direction. The best answer is choice D.
Questions 18 - 21
18.
Choice D is the best answer. Using a bitof common sense and common experience will lead you directly to choice D. All of the frequencies on the plots are within our hearing range, but they are different in describing how sounds of different frequencies are propagated. Choice C is incorrect: It says that at some frequency ranges, v = 0 (i.e., sound waves do noteven propagate). If that were the case, then as someone sang a series of notes ranging from a low pitch to a high pitch, there would be a range of sounds not heard. This does not happen. Choice B is incorrect: It says that sounds of low pitch travel much
faster than sounds of high pitch. If this were true, then you would hear sounds having a higher frequency first when listening
to a distant sound. Since you can hear and usually recognize someone speaking from a distance, and since voices combine several frequencies, this variation in wave speed with changing frequency must not happen. Choice A is also incorrect: It says that the speed varies with frequency in some periodic fashion. This would garble talk and other sounds, and it is
therefore not likely to be a genuine physical phenomenon. The best answer is choice D.
46
19.
Choice A is the best answer. The pitch of a sound you hear is the perceptual correlate of the frequency of that sound wave.
The siren at rest has a fixed frequency for the sound it emits. When the source is approaching, the waves get compressed, and thus its perceived frequency increases. This means that an approaching siren has the greatest frequency (highest pitch) of the different frequencies in the question. Only choice A lists the approaching frequency as the highest. The best answer is
choice A.
20.
Choice D is the best answer. When the cars are moving in the same direction with the same speed, their relative speed is
zero. Therefore, each car hears 400 Hz coming from its own horn and also from the other car's horn. Because there is no difference between the frequencies, there will be no beats. In choices A, B, and C, the cars have different speeds, so their horns will emit waves that are shifted differently, and thus there would be beats and thus a beat frequency. The best answer
is choice D.
21.
Choice C is the best answer. The question asks for the graph that BEST represents the frequency of a sound wave emitted from a closed pipe as a function of the length of the pipe? Let's consider the answer choices:
A. L B. C. I D.
>> a u 3
~
-J
Length (L)
Length (L)
Length (L)
Length (L)
Frequency,/, and pipe length, L, are related through / = nv/4L- This means that/is proportional to 7^, so as one increases,
the other value must decrease, eliminating choice B. The relationship is an inverse one, which is represented by an
Sound Experiment
Choice B is the best answer. What is the wavelength of the sound produced by the tuning fork in Trial 3? To get the
wavelength of this sound, we could resort to the golden rule for waves, v = fX. Solving for wavelength gives X= vlj. The
only problem is that vve do not know the sound speed, v. We could combine ?*. = v/f with / = nwl^.Taking n = 1and solving
for the wavelength gives X = 4L. L is the length of the air column, which is the height of the tube minus the height of the
water. For Trial 3, L = 12.5 cm. Therefore, the wavelength is X = 4L = 50 cm. The best answer is B. 23. Choice C is the best answer. How would the experiment have to be changed, if the same results were desired in a room
heated to a temperature of 25 C? Since the same measured frequencies are desired, the same tuning forks should be used (heating the forks by 5 C would not noticeably change their frequencies). This rules out choices A and B. Heating the room
increases the speed of sound in air. Using the equation given in the passage (/ = nv/4L, with n set equal to 1) shows that the
air column length L must increase by the same percentage as the sound speed, if the same frequencies are to resonate. This means that the water height must be lowered. The best answer is choice C.
24. Choice C is the best answer. How does the speed of sound in Trial 5, V5, compare with the speed of sound in Trial 3, V3?
The speed of sound is governed by the medium, which in this case is air. Since the air temperature is a constant 20C
throughout the experiment, we conclude that the speed of sound is also constant for the experiment. This means V5 = V3. The only way to change the speed of sound in an ideal gas is to change its temperature or pressure. We are assuming air behaves as an ideal gas at room temperature. The best answer is choice C.
25. Choice C is the best answer. The important feature that allows the experiment to work is that there is a phase difference that creates an interface at which the sound wave reflects. Choices A and D are both gases. The original experiment is carried out
with a gas (20 C air) above the water and should work whether the gas is 0 C or 100 C, invalidating both choices. If the space above the water is filled with either a solid or liquid, sound can still propagate through both media. However, if the
medium is 20 C water, there will be no interface, and thus there will be no wave reflection at the water level measured in the
experiment. Wave reflection requires an interface between two media that propagate sound at different speeds. If that difference is not present, there is no reflection, which precludes any resonance other than that involving the entire tube
length. The best answer is choice C.
47
26. Choice A is the best answer. In Trial 5, the height of the water was 75.0 cm. The tuning fork from which other trial could be
used to produce a resonance for a water height of 75.0 cm? If the water height is 75.0 cm, the height of the air column must be
25.0 cm. Which other tuning fork could have a resonance with an air column of 25.0 cm? The relation that must be satisfied is:
/ = nv/4j. The tuning fork for Trial 1 had an aircolumn of L = 8.3 cm. If this length were multiplied by 3, we would get 25
cm. This means the tuning fork for Trial 1 can resonate with a water height of 75.0 cm. A picture might clarify the situation:
The frequency in Trial 1 happens to be 3 times the frequency in Trial 5. The tuning fork in Trial 1 fits three-quarters of a wavelength into the air column, while the tuning fork for Trial 5 fits one-quarter of a wavelength into the air column. The best
answer is choice A.
27. Choice B is the best answer. Suppose the tuning fork in Trial 4 were measured to have a sound intensity level of 50 dB. If a second, identical tuning fork were struck and brought near the first fork, together they would have an intensity that is doubled
that of a single tuning fork. The question is how this will affect the intensity level in terms of decibels. Because their combined
intensity I is twice that of a single tuning fork, we can use a value twice as large in the intensity level calculation.
Such math can be avoided, ifyou remember the following trick regarding decibel levels: If the intensity of a sound increases by a factor of 10, the decibel level increases by +10 dB. Since the intensity increases by a factor of only 2, the intensity level must increase by less than +10 dB. This eliminates choices C and D. Choice A is out, because we know the intensity level had to
increase to some degree. The best answer is choice B.
Jet Radar
28.
Choice D is the best answer. When using active radar (such as a radar gun), the wave reflected from a moving object is in
fact doubly compressed, which leads to a double Doppler shift. This makes choice A valid, so eliminate it. A reference beam
is needed to compare how much the wave has shifted. This makes choice B valid, so eliminate it. The gun operates while stationary or in motion. But when in motion, the speed of the emitter must be factored in. If the speed is analyzed by
comparing the wave reflected from a moving object with the wave reflected from a stationary object, then the motion of the
gun subtracts out. This makes choice C valid, so eliminate it. The best electromagnetic radiation is one that can travel far and
not be much affected by absorbance, refraction, or dispersion. The longer the EM wavelength, the better it is for use in radar. This means that UV, with a short wavelength, would not work well. In addition, it would be expensive and dangerous to send out a signal of such high energy. For practical purposes, communication bands and radar are found at the low-energy/longwavelength end of the electromagnetic spectrum. The best answer is D.
29.
Choice C is the best answer. As stated in the passage, radar uses radio waves, so radar waves they are electromagnetic
waves (which are transverse waves, not longitudinal waves). This eliminates choices A and B. Electromagnetic waves can travel through a vacuum, so radarcan function in a vacuum. In fact, it will operate very well in a vacuum, because there is no
refraction, absorption, or reflection to affect the signal. The best answer is choice C.
48
30.
Choice B is the best answer. The velocity of an object reflecting the wave emitted by a radar gun can be determined by comparing the frequency of the emitted wave with the frequency of the reflected wave. Note that the returning wave is doubly compressed by the moving object when it is reflected. This means that the velocity can be found by knowing the incident frequency and the reflected frequency. None of the choices say this outright, as they all refer to beat frequency. Two consecutive reflected waves have the same frequency, so there is no beat frequency. This eliminates choice A. The wave reflected from a stationary object will not be Doppler-shifted, so it will have the same frequency as the emitted signal. This signal can be compared to the compressed reflected wave to obtain a beat frequency, and thus the velocity of the object. Choice B is the best answer. Choice C is eliminated, because the beat frequency would again be zero. Choice D is eliminated, because the velocity determined from the comparison of the waves reflected from two separate, moving sources
is the relative speed. This can also be applied to eliminate choice C. The best answer is choice B.
31. Choice D is the best answer. The smallest object would be hardest to observe in motion, because the wavelength may be too
long to be reflected by the object. The smallest of the objects is the flying insect, so its velocity is the hardest to measure. As a note, bats use a radar homing system: the squeak emitted by a bat has a frequency that is high enough to detect flying
insects. The best answer is choice D.
32.
Choice D is the best answer. This question requires memory, derivation, or intuition. The shift in frequency is going to be less than the frequency itself in most cases, so choices A and B seem unreasonable. Choice D is better than choice C, given that the wave is doubly compressed (double Doppler-shifted) when it is reflected from a moving object. If you do not buy this approach, then a derivation must be used.
For the first shift, when the wave strikes the movingobject, the object will encounter a wave that has been shifted as follows:
_.
,.., c
vo + vobject r
vo
/incident
For the second shift, when the wave leaves the moving object, the object reflects a compressed wave that has been DopplerSecond shift: /detected =
, ,-r r
vn
vo " vobject
J object =
vn
/v0 + Vobject\t
"
vo " vobject V
v0
J incident - (-
_/vo + v0bject\ ,
\ v0 - v0bject/
J incident
The shift in frequency is the difference between the doubly shifted frequency and /incident- where v0 is c, the /incident is /o.
and v is the speed of the object.
A/ =(^)/o-/o=/o(^-l)=/c(^-|tf) =/c(^)-/o(2f)
The best answer is choice D.
Questions 33 - 36
33.
Choice A is the best answer. This is a question of pattern recognition more than anything else. Let's start by considering the differences between the frequencies rather than the frequencies themselves. 159 differs from 53 by 106 Hz, 265 differs from
159 by 106 Hz, and 371 differs from 265 by 106 Hz, so we see a repeated difference of 106 Hz. From this point, let's look
for a common denominator for the values as well as 106. All of the numbers are divisible by 53 and not 106, so 53 Hz must
be the fundamental frequency. This eliminates choice Cand D. If we divide 53 Hz into the four values listed, vve get 1, 3, 5,
and 7. These are all odd numbers, so we must be dealing with a closed pipe rather than an open pipe. Choice B is eliminated.
The best answer is choice A.
34.
Choice A is the best answer. The depth finder can detect differences in the objects, if their echoes are different in transit time and duration. Bouncing off a rocky bottom, the signal will return to the boat with approximately the same duration as the emitted sound. Rocky bottoms are hard, and they reflect sound waves well. The addition of a "watery silt" does not
change this reflection much. Remember that above the silt is water. Since sound reflections occur when there are abrupt changes in the sound speed between two adjacent media, there is little reflection at the water-silt interface. Therefore, Objects I and II cannot be easily distinguished, ruling out choice B. As for the school of fish, sound would reflect from all of them.
The echo, therefore, will be a diffuse reflection of the emitted pulse-now longer in duration and different in timbre. It will be a noticeably different echo than that arriving from the rocky bottom. The best answer is choice A. 35. Choice C is the best answer. Red shift implies that the visible light is shifted toward the red end of the visible spectrum,
radiation of a lower-energy frequency, and therefore a longer wavelength, than the light. As stated in the question, red shift is attributed to a planet moving away from the observer. Blue shift implies that the light is shifted to a more energetic frequency, which implies that the wavelength has been compressed. This is because the planet (object) is moving towards the
observer. The best answer is choice C.
49
36.
Choice B is the best answer. A longitudinal wave is one in which the vibrating motion of the particles in a medium is parallel to the motion of the wave itself. For a sound wave in air, the air molecules vibrate back and forth in the same direction as the direction in which the wave is traveling. The best answer is choice B.
Organ Pipes
Choice C is the best answer. The harmonics of a pipe are found as /n = n(/j), so harmonics are even multiples of the first harmonic (fundamental frequency). A beat frequency is the difference in frequency between two waves, so if we subtract multiples from one another, the resulting number is also a multiple. It comes down to this: /beat = '/a /b' = na(/l) - nb(/l) = (na - nb)(/i). This means that the beat frequency is a whole number multiple of the fundamental frequency, so it too is a
harmonic. Choice A is a valid statement and thereby eliminated. Choice B is a valid statement, because it defines the harmonics based on their fundamental frequency. Choice C is invalid, because as the harmonic number increases, the wavelength gets shorter, not longer. The equation is incorrect for wavelength, so choice C is invalid and the best answer. As
seen in Equation 1, the length of the pipe definitely impacts the harmonics. The diameter may or may not according to the
lack of information in the passage, so we can only conclude that length means more than width. statement, and thereby eliminated. The best answer is choice C.
38.
Choice D is a valid
Choice A is the best answer. The fundamental mode of a pipe open on both ends has a wavelength that is shorter than that in a pipe of equal length open only at one end. Since v = /A, the doubly open-ended pipe (pipe //l) should have a higher frequency than pipe 1/2. This rules out choices C and D. The wavelengths of the fundamental modes of the two pipes differ by a factor of 2, so the ratio should be 2:1. Choice A is the bestanswer. You could also compare the formulas for closed and
open pipes and determine that /open : /closed = V/2L : V/4L = V2 : V4 =2 : 1, choice A. Athird method for solving this
question involves drawing the pictures. For a pipe open at both ends (like Pipe #1), a halfof a wave fits in the pipe. Fora pipe open at one end and closed at the other end (like Pipe #2), a quarter of a wave fits in the pipe. Thus, the first harmonic has a wavelength of 2L in Pipe #1 and a wavelength of 4L in Pipe #2. Having twice the wavelength results in half the
frequency, supporting choice A as the best choice of the four. The best answer is choice A.
39.
Choice D is the best answer. Changing the type of air could change the speed of sound. Lighter molecules (oratoms) lead to a higher speed of sound, assuming all other factors remain unchanged. Being that H2 (2 amu) is lighter than He (4 amu), sound travels faster in H2 than it travels in He. Since a higher speed of sound means a higher frequency, choices A and C are
incorrect. Based on v= /A, decreasing Awould tend to increase /. Since, shorter pipes result in a shorter sound wavelength,
choice D is the best answer. From the answer choices, you should conclude that using a less massive gas results in a faster
wave speed, because all of the choices involved a gas less massive than N2 and all of the choices dealt with a faster wave
speed (correlated with a high frequency). Perhaps you have experienced this when you breathed in helium and then talked as
you normally would talk. Your voice is of a higher pitch while it is mostly helium exiting your lung. The best answer is
choice D. 40.
Choice B is the best answer. For a gas, you might recall that v V Temperature . This comes from setting 3/2RT equal to
l/2mv2 and solving for the relationship between temperature and average particle speed. Given that the speed of sound
depends directly on the speed of the gas molecules, this means that the Tj:T2 ratio is equal to the vp:v22 ratio. Increasing the temperature by 44% should lead to a new speed that is Vl + 0.44 (= 1.20) times the size of the original speed. This
means that the sound speed increases by .2 or 20%.
J_2 _ 1.44 _ v2
Tl
1.00
^ = 1.20, so v2 = 1.20(vi)
vl
41.
Choice D is the best answer. Meters!!! The length must be calculated using meters, not centimeters. That is the most common mistake made on this problem. This question requires that you plug into Equation 1. The value are n = 3, v = 340
m/s, and L = 0.15 m. The math is solved as follows:
,-!> f m3^340m/s) m3-(340s-i) = 340^1 . 3400s-, = 3400 Hz
2(0.15 m)
0.30
0.10
The best answer is choice D, 3400 Hz. The number seems viable, because 15 cm is pretty short, and from our experience,
shorter pipes generate sounds of a higher pitch. Sound ranges from about 20 Hz to 20,000 Hz, so a frequency of 3400 Hz
seems reasonable for something on the higherend of the musical rangeof pitches. The best answer is choice D.
50
42.
Choice D is the best answer. According to the data in the graph, the first three resonant frequencies are 85, 170, and 255 Hz.
To make the arithmetic as easy as possible, we use the equation / = nv/2h which can be manipulated to give: L= nv/2f =
Vhf r When the fundamental frequency // is85 Hz, v = 340 m/s, and n= 1, we get L= 2 m. The best answer ischoice D.
Sound Resonance
Choice A is the best answer. If a string is held rigid at both ends, only standing waves with nodes at each end can be
generated on that string. The distance between consecutive nodes on a wave is half the wavelength, so the possible wavelengths that can be generated on a string of length L can be written as:
n
where n is an integer. In a pipe open at both ends, the boundary condition is an antinode at each end of the pipe. The
distance between consecutive antinodes is half a wavelength, so the possible wavelengths for a pipe open at both ends are
also:
X = 2L
n
Thus, for a string tied at both ends and a pipe open at both ends with the same length, waves with the same wavelength will be produced. Wavelength and frequency are related by wave speed, v = Xf. The wave speed for waves in pipes is the speed
of sound in air, -340 m/s. The wave speed of waves on a string depends on the tension in the string and the density of the
string. These two wave speeds are not necessarily equal. Therefore, the frequencies of the waves will likely be different.
The best answer is choice A.
44.
Choice B is the best answer. If the air temperature increases, the density of the air decreases (hot air is less dense than cold air). In general, wave speed, v, is related to density, p by:
U -
The speed of sound therefore increases if the air temperature increases. However, the wave speed of a wave on a string is not affected by temperature (thermal expansion of the string is being neglected). Wavelength, frequency, and wave speed are related by v = Xf. If we ignore any thermal expansion of the pipe and the string, then the wavelength of the waves produced in the string and the pipe do not change. For a string, the changing temperature does not affect the wave speed. The wavelength remains the same, so the frequency does not change. For the pipe, the wave speed increases with increasing
temperature. The wavelength is unaffected, so the frequency must also increase. Note that you do not need to know the
exact relationship between wave speed and density to answer this question, but you do need to know that wave speed is in
some way inversely related to density of the medium. The best answer is choice B. 45. Choice C is the best answer. Although the wave on the string was originally produced on the string, the reason such a wave
can be heard at all is because this wave causes the air to vibrate at the same frequency as the string wave. It is this wave that reaches the ear. Thus, the wave on the string and the wave produced in the pipe will produce a beat frequency. The best
answer is choice C.
46.
Choice D is the best answer. For strings tied at both ends, and a pipe closed at one end, the respective possible frequencies
are:
Because of the4 in the denominator for the pipeand the 2 in the denominator for the string, one might be tempted to say that
the pipe will always produce a higher frequency, but that is true if the wave speeds are equal, or if the wave speed on the string is less than the speed of sound in air. We need to know something about the two wave speeds before we can answer this question. Without knowing that information, it cannot besolved definitively. The best answer is choice D.
47.
Choice B is the best answer. Pipes closed at one end and open at the other must have a node at the closed end and an antinode at the open end. Theses are the boundary conditions for the waves produced in pipes closed at one end. If a way could be found to duplicate these same boundary conditions on a string, then the waves in the pipe and the waves on the
string would have the same shape. How could the boundary conditions be duplicated? Tie the string down at one end and
leave the other end free to move. The tied end has to be a node and the free end has to be an antinode. The best answer is
choice B.
51
48.
Choice B is the best answer. A sound wave is a propagation of energy through a medium. The waves produced in pipes travel through air. However, there is no air in a vacuum, so no wave can be produced in the pipe. A wave can be produced on the string, however, because the string is the medium. The string can be plucked and set into vibrational motion. Could you hear this wave? The best answer is choice B.
Questions 49 - 52
49.
Choice C is the best answer. The intensity of a sound is related to the distance r of one perceiving it from the sound source
by the equation I 1/r2. We know from the equation in the passage that the intensity of a 100-dB noise is 100,000 times
greater than the intensity of a 50-dB noise. V100,000 is 316.2, so choice C is the best answer. A good approximation to
follow is that the decibel level of a sound drops by 10 dB every time the distance from the source triples. A drop of 50 dB
results from anincrease indistance of approximately 35. The best answer is choice C.
50.
Choice C is the best answer. The bat detects its possible prey and the location of that prey by bouncing sound waves off it. Since sound can bounce off glass, the bat could detect the glass and believe that the prey is actually at the location of the glass. (Note that this assumes the obviously very hungry bat interprets the glass as prey.) Since the glass is closer than the
actual prey, the bat believes the prey is closer than it actually is. The best answer is choice C.
51.
Choice D is the best answer. This is a two-in-one question, which is quite common on the MCAT. First, let's consider the intensity of the echo. Let's start by saying that the initial sound wave has 100% intensity. At the air-rock interface, someof
that wave reflects back (generating the first echo) and some refracts into the rock. The sound that enters the rock will
continue on and strikethe rock-water interface, where it will partially reflectand partlyrefract. The reflected wave will travel
back tothe rock-air interface, where again some ofthe wave will reflect and some will refract The portion that refracts goes on to beEcho II. Because Echo I results from reflection offa surface with of greater density, thereflected wave will be more
intense than the refracted wave. As such, Echo I must be more intense than Echo II. This eliminates choice A.
Now letsconsider the travel timefor eachecho. The total distance traveled by Echo I is 2d while the total distance traveled
by Echo II is 4d. If both echoes travel at the same speed, then the time for Echo II should be exactly twice that of Echo I. However, the speed of sound isfaster in a solid than it isin air, soEcho II will have a greater average speed than Echo I. So despite traveling twice the distance, because Echo II travels at a greater average speed, it will take less time than double that
of Echo I. The best answer is choice D.
52.
Choice D is the best answer. A beat frequency results from the interference of two waves with different frequencies.
Fortunately, the math that goes with a beat frequency is simple. The beat frequency is simply the difference between the two
frequencies. Ifone tuning fork has afrequency of450 Hz and the beat frequency is 12 Hz, then the other tuning fork must be
either 12 Hzgreater OR 12Hzless. This would lead to potential frequencies of 438 Hzor 462 Hz, not 438 Hzand 462 Hz.If
you didn't read the answer choices carefully, which could happen when you're in a hurry oron your last question and ready
for it to be over, thenyou mighthave mistakenly chosen choice B. The best answer is choice D.
52
Fluids and
Solids
Physics Chapter 7
fc
1) _>
vf"*^
fY"*Vw
^
-
by
the
Berkeley Review
__ Pobject
Pobject
Q =
8t|L
A1V1 = A2v2
Important Concept
Poiseuille's law describes the flow of an ideal fluid through a pipe(many questions involve blood flow)
Point 1 Point 2 Point 3
Pmedium
<
1 1
r,_^
WJpfecfe
Physics
Fluid Properties
Fluid Properties
By definition, a fluid is any matter that flows. This means that liquids (such as water) and gases (such as air) are both considered to be fluids. On a macroscopic scale, these two fluids are involved in the majority of the weather patterns in our planet's atmosphere. On a microscopic scale, they are also involved in the maintenance of living organisms. In this section, we will look at both fluid statics (the physics of stationary fluids) and fluid dynamics (the physics of fluids in motion). Newton's laws will help us obtain a firm understanding of the topics
that we will discuss.
density are kg/m3. When all other factors are held constant, the density ofa fluid
will remain the same as long as its volume does not change, given that the mass
of a material is constant unless some matter is gained or lost.
p _ mass _ m_
volume v
(7.1)
Table 7-1 lists the densities of various substances (both solid and liquid) in
Liquids
Density
Material
Gases Density
(kg/m3)
2.70 x 103
(kg/m3) Material
0.82 x 103
Helium (0C)
(kg/m3)
0.09
0.18
Copper
Silver
0.88 x 103
1.00 xlO3 1.03 x 103 1.06 x 103 13.6 x 103
Nitrogen (0C)
Air(30C)
1.25
1.16
Gold
Platinum
Osmium
19.3 x 103
21.4 xlO3
22.6 x 103
Air(20C)
1.21
Whole blood
1.29 1.43
1400
Mercury
Moon
Earth
Neutron Star
55
PhysiCS
Example 7.1a
Fluid Properties
Two equal masses of liquid and solid water have volumes of 5.00 mL and 5.45 mL, respectively. The ratio of the density of the: A. B. C. D. liquid water to that of the solid water is 0.083 to 1. solid water to that of the liquid water is 0.083 to 1. liquid water to that of the solid water is 0.917 to 1 solid water to that of the liquid water is 0.917 to 1.
Solution
Liquid water is denser than solid water, because it occupies less volume for an equal mass as the solid. So the bigger number should be associated with liquid
water in the ratio. That rules out choices A and C. Next, is ice that much less
dense than liquid water? Not really. If you look into a cup of iced water, the ice cubes do float (indicating they are less dense than the liquid), but they floatwith a very small amount of ice above the liquid's surface. Therefore, liquid water
cannot be ten times denser then ice, as choice B indicates. Their densities must be
A more formal way to do any ratio problem is to use the ratio technique. Since we want a ratio of densities, we identify the appropriate density formula and write it
once for each situation of interest. Here, the relevant formula is equation (7.1), since we are told about mass and volume. Next, find the ratio by dividing one
equation into the other. Our division looks like this:
PH20(s)
The masses cancel each other out, because they are the same. At this point, look to see which answer is the closest to the ratio here. 5.45 is bigger than 5.00,
indicating that the bigger number should be on the water side of the answer. This, again, rules out choices A and C. Next, the two numbers are not all that
different, making choice D the more attractive of the remaining choices. Always minimize the amount of arithmetic you do for a problem by conceptually
approximating the answer.
The best answer is choice D.
Example 7.1b
Ten mL each of pure water and saltwater have densities of 1.00 g/mL and 1.03 g/mL, respectively. The ratio ofthemass ofpure water to that ofsaltwater is:
A. 1 to 1.03. B. 1.03 to 1. C. 0.03 to 1. D. 1 to 0.03. Solution
massive (weighs more) than an equal volume of pure water. So the bigger
number should be on the right side of the ratio. That rules out choices B and D. Saltwateris just slightly denser than pure water, so the ratio of the masses should
be relatively close to 1:1. The ratio of the masses could not be as large as choice
C indicates, which points to choiceA as the best answer.
The best answer is choice A.
56
Physics
Fluid Properties
The specific gravity of a material is defined as the ratio of its density to the density of water at 4 C. Specific gravity is also called the relative density (probably due to the fact that "specific gravity" really has nothing to do with gravity). If a given material has a density p, then its relative density prelative 0-e.,
specificgravity) can be given by equation (7.2):
Specific gravity
Prelative =-&&**&
(7.2)
PH2Q at 4C
P=^
(7.3)
For a given force, a smaller contact area produces a greater pressure. This is why a sharp knife, with its smaller contact area, cuts (i.e., exceeds a critical pressure) more easily than a dull knife. Needles are designed with this principle in mind. The SI unit of pressure is the pascal (Pa), which is equivalent to N/m2. The pascal is an extremely small unit, so it is impractical for describing atmospheric conditions. We generally use the units of atmosphere and mmHg (also known as
a torr) to measure everyday pressures.
The pressure of a fluid can vary with elevation. For example, if you hike to the top of a high mountain, you should notice a decrease in the air pressure. Similarly, if you have ever been diving under water, you have surely felt an increase in the water pressure on your body (especially in your ears and sinuses).
An analogy can be made between pressure variation with depth and the stacking of pennies. Suppose that each penny represents a thin layer of air. If we place a single penny on a table, then the only pressure on that penny comes from the air above it. If we place a second penny on top of the first penny, then the first penny is supporting not only the penny above it, but also the air above that second penny. The more pennies we stack on top of the first penny, the greater the pressure that first penny experiences (Figure 7-1). This simply tells us that pressure is additive.
Column of air
First penny
Figure 7-1
57
Physics
Fluid Properties
Consider the shaded area of fluid shown in Figure 7-2. Suppose the bottom surface of this area is at a height y\t while the top surface is at a height y2- We can
also define the positive y-axis to be pointed upward.
Y2
y2-yr
Lyi
I
Figure 7-2
The fluid below the surface at yi pushes up on the shaded fluid with a force Fi, as given by equation (7.4). The fluid above the surface at y2 pushes down on the shaded fluid with a force F2, given by equation (7.5).
Fj = PiA F2 = P2A
Fj - F2 - w = 0
(7.4)
(7.5) (7.6) (7.7)
PjA - P2A - w = 0
There is also a third force acting on the shaded fluid. That third force is the
weight w ofthe shaded fluid itself. Ifourshaded area offluid isnotmoving, then
it must be in a state of equilibrium. This means that Fi, F2, and w must sum to
zero, as shown in equation (7.6). Substitution of equations (7.4) and (7.5) into
equation (7.6) gives equation (7.7).
The volume V of the shaded area of fluid can be given by equation (7.8). The shaded area of fluid by substituting equation (7.1) and (7.8) into equation (7.9). This gives equation (7.10). In arriving at this equation, we areassuming that the
density of the fluid remains constantas elevationchanges.
V = area x height = A (y2 - yi)
w = mg
weight ofan object is given by equation (7.9). We can solve for the weight of the
(7.8)
(7.9) (7.10)
We can now substitute equation (7.10) into equation (7.7), to produce equation (7.11). Dividing by the area gives equation (7.12).
PlA-P2A-p(A(y2-y1))g = 0
Pascal's principle
Pi-Po =
(7.11)
(7.12)
58
Physics
Fluid Properties
Equation (7.12) tells us that if we increase the pressure on the upper surface of
the shaded area in Figure 7-3, then the pressure on the lower surface will increase by exactly the same amount. This is called Pascal's principle. It states thata pressure appliedto an enclosed fluid is transmitted equally throughoutthe
fluid and to the walls of the fluid's container.
Example 7.2a
At a specific depth in a swimming pool, a barometer measures the total pressure to be twice that of atmospheric pressure. If the barometeris now submerged to a depth that is twice its initial depth, by how much does the total pressure
increase?
A. B. C. D.
The pressure increases by 50%. The pressure increases by 100%. The pressure increases by 200%. The pressure increases by 300%.
Solution
We can use the ratio technique to handle this percentage change type of problem. The relevant situation here is the relationship of pressure to depth:
Ptotal = Patm + Pgh
Applying this to the first depth implies that pghinitial=Patnv since me total pressure there is 2Patm. If the second depth is twice that of the first, then Pghfinal = 2Patm- This means that the total pressure at the second depth is SPatmTaking the ratio of the final to the initial situation gives:
Ptotal final *total initial _ 3Patm 2-P.a tm
= 1.5
To complete this problem, just subtract 1 from the ratio to get the percentage change of +0.5 (i.e., 50%.) Be careful of the wording in percentage questions. Here, we want a "percentage change." If the question had asked instead, "What percentage of the initial total pressure is the final total pressure?", the answer
would have been: "The final total pressure is 150% of the initial total pressure."
The best answer is choice A.
Example 7.2b
A swimmer is at the bottom of a 5-meter pool, where the gauge pressure (pgh) is approximately 0.5Patm. If the swimmer rises to the surface, by how much does the total pressure change?
A. B. C. D. The total pressure increases by 33%. The total pressure increases by 66%. The total pressure decreases by 33%. The total pressure decreases by 66%.
Solution
As with 7.2a, the relevant situation here is the relationship of pressure to depth:
Ptotal = Patm + Pgh
Pinitial = 1*0arxn + 0.5 atm = 1.5 atm; Pfinal = 1.0 atm; AP = 0.5 atm
The total pressure is reduced, so choices A and B are eliminated. The ratio of AP to Pinitial is 1:3, so the pressure drops by 33%.
The best answer is choice C.
59
Physics
Fluid Properties
him as a man of genius. Archimedes is the man who ran naked through the streets of Syracuse shouting "Eureka, eureka!" (Greek for "I have found (it)!"), after he discovered the principle of hydrostatics (buoyancy). King Hiero II had
asked Archimedes to determine whether a crown was pure gold or laced with silver. While relaxing in the public baths, Archimedes realized that he could determine the volume of the crown by placing it in a container of water and then measuring the amount of water the crown displaced.This volume was compared to an equal volume of pure gold. After a short calculation involving density, Archimedes reported to Hiero that the crown contained some silver. The maker
of the crown was executed, and Archimedes made his place in history. So, what was Archimedes' great insight about objects in fluids? He realized that the water (or any fluid) below a floating object supports that object against gravity. To get an idea of just how big this upward buoyant force B is, ask yourself what the water beneath a battleship would be supporting, if the ship were not there. The water would be supporting a column of water above it. Figure 7-3a shows a filled tank, with an object resting on the bottom of the tank. The objectappears to weigh less underwater than in air. Why? Because the water surrounding it is trying to push the objectup and out of the way with some force B. Since the object is stationary, the buoyant force and normal force combined must be equal in magnitude to the weight of the object.
(a)
(b)
*-
(c)
-
tB
*-
Pobject> Pwater
B
r-.
iii
1
*
img
Pobject "^ Pwater
''M't
i
rmj
Figure 7-3
Whathappenswhenthe object has the samedensity as the surrounding water, as in Figure 7-3b? If the object has the same volume and mass as the displaced region of water, the object should hover in the water. After all, both the object and the displaced water have the same weightand experience the same buoyant
force. With this in mind, we can state what Archimedes discovered in the tub:
The buoyant force acting upon an object is equal to the weight of the fluid it displaces. Mathematically, thebuoyantforce B is found usingequation (7.13).
Archimedes' principle
(7.13)
where the mass of the displaced fluid is in terms of its density and volume. How does the density of the object in Figure 7-3c compare with the water? If we put an object of equal size, but of lesser density, into the water, as shown in Figure 7-3c, it should float above the water line, because the buoyant force must balance its weight. Since it has less weight than the object in Figure 7-3b, the buoyant force necessary to make this object float will be smaller (i.e., it will
displace less water).
60
Physics
Fluid Properties
What if an object's density exceeds that of the water? Its weight will exceed the
buoyant force, and it will sink (as shown in Figure 73a). As this object falls, however, it will accelerate with an acceleration smaller than g (and appear to weigh less), because the water still exerts an upward buoyant force on it. This buoyant force is a property of any fluid (liquid or gas) in a gravitational field. Ifs
the reason helium balloons float in the air, ships sail on the surface of a body of
water, and submarines can ascend and descend in surrounding water by taking
on or bilging out water.
Example 7.3a
I.
Balloons rise when their total density is less than that of the air surrounding
them.
II. Balloons fall when the buoyant force of the air surrounding them exceeds their weight. III. Balloons stop falling when the air surrounding them is evacuated.
A. B. C.
D.
Solution
To handle these multiple-concepts type of problems, go through the list eliminating or accepting one item at a time. Then cross out the incorrect choices. Let's say that you immediately decide Statement III is false. After all, balloons floatbecause the surrounding air buoys them up. No air equates to no buoyancy.
This means that Statement III should be in the answer and that choice A is
incorrect.
Let'ssay further that you know Statement I is true and therefore should not be in the answer. After all, helium is lighter than air, and helium balloons float. This would rule out any choices that contained Statement I and leaves only choice C as the correct choice. You are now done with this question, so you can move on. Do only enough work on a problem to convince yourself you have the best answer and then pick the choice and move on. You could also have considered Statement n, knowing that an object will accelerate down when the downward force exceeds the upward force. A balloon will not fall when the buoyant force of the air surrounding them exceeds its weight.
The best answer is choice C.
Example 7.3b
Which of the following are TRUE regarding three balls of equal size that are fully
submerged in water, if Ball A sinks, Ball B is stationary, and Ball C rises?
I. II.
61
Physics
Solution
Fluid Properties
buoyant force exceeds its weight. This is possible if Ball C is less dense than the surrounding water. Ball B floats when submerged in the water, which tells us
that the buoyantforce equals its weight. Thisis possible if Ball Bis equally dense as the surrounding water. It is true that Ball C is lessdense than Ball B.
Statement I: Ball C rises when submerged in the water, which tells us that the
Statement II: The buoyant force a fluid exerts on an object depends on the density of the surrounding medium, the volume of the object, and the
gravitational force constant (B = pfluid ' ^displaced ' g)- Because Ball A has the
same volume as Ball C, they experience the same buoyant force. The reason Ball A sinks and Ball C floats has to do with their differences in weight, despite the fact that they experience the same buoyant force. It is false that the buoyant force on Ball C is greater than that on BallA.
Statement III: Ball A sinks when submerged in the water, which tells us that its weight exceeds the buoyant force. This is possible if Ball A is denser than the surrounding water. It is true that the density of Ball A is greater than that of
water.
Figure 7-4shows a summary of the mathematics associated with a floating object and a sunken object in a tank of fluid. The conclusions can be used to quickly answer multiple-choice questions.
W = B
B=PmediuirTVdisplaced"g
Pobject"Vobject = Pmedium"Vdisplaced
^displaced _ Pobject
Q
W= mg= PobjecfVobjecfg
v
^object
Pmedium
" Pmedium"^object'g
N = Apparent Weight W
Specific Gravity = ^
Pwater
Pmedium'Vobject*g
Pmedium
W=mg =Pobject*Vobjecfg
62
Physics
Example 7.4a
Fluid Properties
B.
C. D.
Solution
Because the object floats in the petroleum ether, it must be less dense than the surrounding fluid. The density is less than 0.90 g/mL, so choices C and D are
eliminated.
From here it is best to use the shortcut presented in Figure 7-4. The percent of the object that is submerged is equal to the relative densities of the object and medium. This means mat the density of the object is the product of the percent submerged and the density of the petroleum ether.
%submerged = Pobject
Pmedium
Pobject
0.90
Example 7.4b
What is the specific gravity of an object that weighs 36 newtons in air but only 9
newtons in water at 4C?
A. B. C. D. 0.25 1.33 3.00 4.00
Solution
The first thing to do is to identify that the object is a sunken object rather than a floating object. The object must be denser than the medium, so the specific gravity must be greater than 1. This eliminates choice A. For a sunken object, the ratio of the weight of the object to the buoyant force is equal to the relative densities of the object and medium. The objectweighs 36 N in air, so its weight is 36 N. It has an apparent weight of 9 N in water, so the normal force is 9 N and the buoyant force must be 27 N. Keep in mind that a sunken object rests on the bottom of the container, where because it experiences no acceleration, it has a net force of zero. This means that on the bottom of the tank, mg = N + B.
B must be 27 N
N = 9N
To get the specific gravity (the relative densities), we simply divide 36by 27:
Specific Gravity =
The best answer is choice B.
W
mg = 36 N
27
63
Physics
Fluid Properties
Surface Tension
We usually drink water from a cup. The water is confined by the cup, which keeps the water molecules from spreading apart, and you from cleaning up a spill. What, however, keeps the molecules that make up a small water droplet from spreading apart? The droplets tend to stay together because their molecules
are attracted to each other-this attraction is typically a result of intermolecular
forces such as hydrogen bonding or van der Waals interactions. Within the bulk of the droplet, each molecule reacts to attractive forces from all its neighbors and, on average, experiences no net change. Figure 7-5 shows a molecular view near the surface of a droplet. At the surface, however, the situation is tense. A surface molecule is subjected to a net force pulling it towards the center of mass, since
there are few molecules above the surface to pull it out. On average, these surface molecules are pulled towards the center of mass. This reduces the number of surface moleculesand, as a result, reduces the surface area of the droplet.
Surface area shrinks as the molecule is
Surface area shrunk after the molecule is
Figure 7-5
The force associated with this tendency of the surface of a liquid to pull inward and shrink in area is known as the surface tension. When weight is significant, droplets tend to have flattened fluid surfaces. When the gravitational force is relatively small, or negligible, surface tension shrinks the surface area of a liquid by forming a sphere. This is why your coffee has a flat surfaceand soap bubbles
are round.
Surface tension should relate to other surface phenomena, such as evaporation and condensation, because they all occur at the fluid's surface. How do they relate to each other? If the surface tension is relatively strong, the molecular attractive forces are relatively strong. Because of hydrogen bonding, water has a greatersurface tension than ethanol. At a given pressure and temperature, which evaporatesfirst? Ethanol willevaporate before water evaporates under the same conditions. It has a smaller surface tension. Which is more likely to condense? Water is more likely to condense than ethanol, because it has a greater surface
tension and, consequently, stronger attractive intermolecular forces. In the
A. make the cell's shape more spherical. B. make the cell membrane more pliable.
C. make the cell flatten.
64
Physics
Solution
Fluid Properties
Surface tension is a surface effect. As such, it can affect surface properties of the cell, including possible shape changes. It will not change the volume of the cell, since the amount of intercellular material is generally constant. That rules out choice D. As for the shape of the surface membrane, increasing tension on the membrane makes it less pliable, ruling out choice B. Imagine how the pliability
of a balloon surface decreases as you inflate it. When surface tension increases on
a liquid, its surface decreases in area (although its volume does not change). The resulting shape always tends towards spherical. You can see this with a soap bubble. You should try to make useful analogies with everyday phenomena to answer questions about things you can't easily see.
The best answer is choice A.
Example 7.5b
A sealed vessel contains two chambers separated by a phospholipid bilayer membrane. After completion of an experiment on the vessel, the membrane distorts, as shown below. This distortion may have occurred because the pressure on the right side of the vessel:
.
Membrane
Membrane
Before experiment
A. B. C. D.
After experiment
increased, and the membrane's surface tension increased. increased, and the membrane's surface tension decreased. decreased, and the membrane's surface tension increased. decreased, and the membrane's surface tension decreased.
Solution
The membrane is being forced to the left, so pressure on the right side must have increased relative to the pressure on the left side of the membrane. This eliminates choices C and D. Because the molecules of membrane are being stretched apart, they are feeling less of an attractive force towards one another. This means that the membrane's surface tension must have decreased, making choice B a better explanation than choice A.
The best answer is choice B.
65
Physics
Fluids in Motion
Fluids in Motion
in fluids is called viscosity and is denoted by the Greek letter eta, rj. The SI unit
ofviscosity isNs/m2.
Viscous forces retard the motion of one part of a fluid relative to another part of the fluid. If two layers of a fluid are held together tightly, then the viscosity of the
fluid is said to be large. If the viscosity of a fluid is large, then that fluid will
move slowly. This can be seen if we consider the difference between pouring
honey into a cup and water into a cup. Since the coefficient of viscosity (r)) for honey is greater than that for water, honey will flow at a slower rate than water.
Liquids
Viscosity
Material
Gases Viscosity
Material
(kg/m3)
(kg/m3)
1.71 x 10"5 1.81 x 10"5 1.87 x 10"5 2.18 x 10"5
Water (37C)
Water (100C) Blood Plasma (37DC)
2.08 x 10"3
5.3
0.97
1.71 x 10"2
Table 7-2
temperatures. Generally, if we were to increase the temperature of a fluid, the viscosity of a liquid would decrease, while the viscosity of a gas would increase.
You may notice that Castor oil shows a significant drop in viscosity as
temperature increases. This property makes it an ideal lubricant for an engine. When a simple fluid flows through a pipe, the speed of that fluid is greatest at the central axis of the pipe and essentially zero along the walls of the pipe (Figure 7-6). A common reason that the fluid along the walls of a pipe does not move is because that fluid encounters the rough and uneven molecular surface of the pipe itself. Molecules of fluid in contact with this surface tend to reside in its
crevices and to not move.
Fluid at the edge of the pipe flows the slowest. This flow speed is zero for most simple fluids.
.....- -. -i
Figure 7-6
66
Physics
Fluids in Motion
As a fluid is flowing through the center of a pipe oflength Lwitha certain speed
v, there is a force that tends to oppose the fluid's motion. That force is called a viscous retarding force F and it is caused by the fluid's resistance to flow. The magnitude of the viscous retarding force is given by equation (7.14):
F = 4jtt|Lv
(7.14)
For a fluid to flow through a pipe at constant speed, the viscous retarding force must be balancedby an applied force. Suppose the pressure of the fluid entering the pipe in Figure 7-6 is Pi. The force pushing this fluid into the pipe is Fi = PiA,
where A is the cross-sectional area of the pipe (i.e., A = to*2). There is also a
pressure P2 at the end of the pipe that tends to oppose the motion of the fluid. The force associated with this pressure is F2 = P2A. The net driving force of the fluid through the pipe is shown in equation (7.15). It is simply the difference in
between these two forces:
Fi - F2 = (Pi - P2)A
(7.15)
For the fluid to flow through the center of the pipe at constant speed, the driving force and the retarding force must be equal (see equation (7.16)). If we substitute
tit2for the cross-sectional area of the pipe and then rearrange equation (7.16), we
will get equation (7.17). This equation allows us to relate the pressures at the two ends of the pipe to the viscosity of the fluid and the physical properties of the pipe itself (i.e., length and radius). We could also solve for the velocity v of the fluid at the center of the pipe by rearranging equation (7.17) into equation (7.18):
4jtt|Lv = (Pi - P2)A
(7.16)
Pl-P2=(^)v
v = [P!^2)r2
4r)L
(7.17)
(7.18)
Example 7.6a
Which of the following graphs BEST represents the viscosity of pure H20 as its temperature increases?
B. c.
2U
U
D.
2u
2H
u
In cm 1
*->
a,.
(0
flj
P-
p-
p-
1 > 1 111 1
0 20 40 60
I I I I I I I
0 20 40 60
I I I I I I I
0 20 40 60
I I I I I I I
0 20 40 60
T(C)
T(C)
T(C)
T(C)
67
Physics
Solution
Fluids in Motion
This is a graph-identification problem. First, think about the qualitative relationship between viscosity and temperature. Should the viscosity of water increase or decrease as the temperature increases? As you heat up water, the molecules should start to spread apart from one another, which means that it should decrease. One way to remember this is to cook some canned soup. The soup comes out of the can as a viscous, unappetizing gelatinous lump, but it thins as you heat it, evolving into a tasty, salt-laden meal. The soup is mostly water, suggesting that water thins as it heats up (although the overriding determining factor is actually the soup's ingredients). This rules out choices C
and D, which show no change in viscosity with temperature and an increase in
viscosity with temperature respectively. To decide betweenchoices A and B, look at the value on the y-axis when the temperature is 20C. How do they differ? Choice A smoothly drops from about 2 to 0.5 over a 60C range, passing through
1 at 20C. In choice B, the number abruptly drops from about 2 to nearly 0 over a
range of 10C and more importantly, does not equal 1 at 20C. The y-axis shows the actual viscosity of water divided by the viscosity of water at 20C, so the
value of that term at 20C must be 1. Choice B does not fit that criterion, so it
cannot be the best answer.
Example 7.6b In calibrating a flow meter, an engineer measures the total pressure drop across a pipe as a function of the gas flow velocity. Which of the following plots BEST
details his results?
I I I I I I
0 2 4
v(m/s)
Solution
v (m/s)
v (m/s)
v(m/s)
Fluids flow from regions of higher pressure to regions of lower pressure, so in order to get a fluid (such as a gas) to flow, there must be a AP across the length of the pipe. It should seem intuitive that a greater pressure difference would push fluid faster, so choice D can be eliminated. Also, choice C implies that the speed can increase despite no increase in pressure difference past a threshold, which is not true. Choice C is also eliminated. A change in AP from a negative value to a positive value implies that the pressure gradient reversed directions. This would
reverse the direction of the fluid flow, and that is not what choice A shows. The
relationship between velocity and pressure difference is linear and both should be equal to zero at the same time. Only choice B shows this.
The best answer is choice B.
68
Physics
Fluids in Motion
The flow rate Q is the volume Voffluid that passes through a pipe perunittime t. Note thatthe flow rate and flow speed ofa fluid are not the same thing. What type ofpressure would be needed to maintain a certain flow ratethrough a pipe? We canrelate the flow rate to the cross-sectional area ofthe pipe and the average
speed v of the fluid by equation (7.19). Recall that we have mentioned that the fluid in a pipe flows the fastest at the center of the pipe and does not flow at all at
the edges of the pipe. Using this assumption, we can express the average speed
Q = Y. = vA
t
v" = v
2
(7.20)
If we substitute equation (7.20) into equation (7.19) and include the cross-
Substitution of equation (7.18) into equation (7.21) will give equation (7.22). This equation is called Poiseuille's principle, after Jean Poiseuille, a French physician.
Poiseuille's principle
Q=H.-(Pl-P2)
8r|L
(7.22)
The important parameter in equation (7.22) is the r4 term. Note that if the radius
of the pipe is doubled, the flow rate increases by a factor of 16.
A common application of Poiseuille's principle involves the flow of blood through the circulatory system. Although it applies to an ideal fluid, which blood is not, it still gives a good approximation of the flow dynamics of blood through the body. When the heart contracts, it generates a large Pi, which in turn establishes a pressure difference in the circulatory system ultimately causing blood to circulate and return to the heart. Thus, when one describes a patient as having "high blood pressure", it means that their heart is generating a very large Pi in order to produce the necessary Q to get blood to the tissue in a timely
fashion.
Although we have presented Poiseuille's principle as a mathematical expression to this point, at the level of the MCAT it is highly conceptual. For instance, it explains that an extremely tall person will have a greater strain on their heart than a person of average height, because in order to generate the same volume flow rate (Q), a tall person requires a greater AP to offset the greater L associated with their longer circulatory system. The equation also explains why it takes longer to pour syrup than it takes to pour water and why a wider straw is much more efficient for obtaining a chilled, carbonated beverage from a glass than a thinner straw. It basically explains important things.
69
Physics
Fluids in Motion
Which single change, where all other factors stay constant, gives the LARGEST
increase in the volumetric flow rate of synthetic blood plasmathrough a tube?
A. Doubling the tube radius.
These quantitative-change problems usually require you to know the basic functional relationship between variables used in some relevant equation. That is, you need to know whether the important variables are in the numerator or denominator, and whether they are squared or cubed, or whatever. Here, the basic equation to use is Poiseuille's principle, equation (7.22). The relevant variables for this problem are the tube radius r, the pressure difference Pi - P2, the tube length L, and the plasma viscosity rj. The ji and 8 are not important quantities, because in any quantitative-change problem, constants will never
enter into consideration. Now, go through each choice, and see how that will change the volumetric flow rate. For choice A, what would doubling the radius do to the flow rate? It would increase the flow rate 16 times (i.e., 24). Choice B would quadruple the flow rate, since the pressure difference term in the equation is not squared or quadrupled, but raised to the first power. Cross out choice B,
because choice A is better. Choice C would double the flow rate, since the
viscosityis in the denominator and to the first power. But choiceA is still a better choice. Halving the tube length would have the same effect as choice C, making choice A correct. This formula is a bit daunting and may be given in the passage, but it is common enough to make its basic functional variables worth knowing.
The best answer is choice A.
Example 7.7b
Whichsingle changemakesit easiest(i.e., creates the smallest pressure difference between your mouth and the atmosphere) to drink a milkshake?
A. Increasing the straw length by 50%, but keeping the flow rate and milkshake
fixed.
B. Decreasing the straw radius by 50%, but keeping the flow rate and milkshake
fixed.
C. Melting the shake until its viscosity drops by 50%, but keeping the flow rate
and straw fixed.
D. Drinking the shake at 25% of the usual flow rate, without changing the straw
or shake.
Solution
To keep the flow rate fixed while increasing the straw's length by 50% would require 1.5 times the pressure difference across the straw, so choice A is out. To keep the flow rate fixed while halving the straw's radius would require sixteen times the pressure difference across the straw, so choice B is eliminated. To keep the flow rate fixed while halving the shake's viscosity would require half the pressure difference across the straw, so choice C is possible. To reduce the flow rate by a factor of four while keeping other factors constant would require onefourth the pressure difference across the straw, so choice D is the easiest change.
The best answer is choice D.
70
Physics
Continuity Equation
Fluids in Motion
In equation (7.19), we saw how to relate the flow rate, Q, of a liquid to the crosssectional area A of a pipe and the average velocity v of the fluid flowing in that pipe. This relationship was for a pipe or tube whose cross-sectional area does not
change. However, not all tubes retain the same cross-sectional area. Consider the human circulatory system. As blood leaves the left atrium of the heart it flows into the aorta, which has a radius of about 1.3 cm. As the blood leaves the aorta,
it passes into arteries having smaller radii. In the case of the human circulatory
system, the cross-sectional areas of the blood vessels vary greatly.
Suppose the aorta has cross-sectionalarea Ai and that blood flows from the aorta into an artery with cross-sectional area A2 (Figure 7-7).
Larger Area Slower Speed
vl Smaller Area
Faster Speed
v2
Figure 7-7
Assuming the fluid is incompressible, at any given moment in time, the fluid entering the region at Ai must equal the fluid leaving the region at A2. In other words, the volume flow rate into the region at Aj must equal the volume flow rate out of the region at A2. The volume flow rate for the region at Ai is given by Q = Ajv}, while the volume flow rate at region A2 is given by Q = A2v^. In both of these equations, the average speed V of the fluid refers to that fluid passing a given cross-sectional area. Since the flow rates for these two regions must be equal, we can write equation (7.23):
Continuity equation
^^jv^^2^J
(7.23)
Equation (7.23) is called the continuity equation. It will become important when we discuss Bernoulli's equation. Note that if the cross-sectional area A2 in Figure 7-4 is smaller than the cross-sectional area A}, then the speed of the fluid passing through A2 must be greater than the speed of the fluid passing through A\. This
has to be the case in order for the volume flow rate of the fluid to be constant.
The continuity equation can also apply to branching as long as the fluid is incompressible and that the total cross-sectional of all of the branches is considered. For the system shown in Figure 7-8, equation (7.24) applies.
AjVx = A2V2 + A3V3 + A4V4
(7.24)
Alvl
Figure 7-8
71
Physics
Fluids in Motion
Atherosclerosis is the thickening and hardening of the arterialwalls. The aorta of a healthy adult has a radius of about 1.3 cm and a blood flow velocity of about 0.5 m/s. An atherosclerosis-stricken bacon epicure is found to have an effective aortic radius that is 75% of that in a healthy aorta. What is the blood flow velocity through the narrowed section of artery? (Assume that the blood's volumetric
flow rate is constant for all adults.)
A. B. C. D. 0.28 m/s 0.38 m/s 0.66 m/s 0.89 m/s
Solution
Before invoking math, ask yourself if the blood will flow more quickly or more slowly through the narrowed artery. It should flow faster, ruling out choices A and B. Remember, for a fixed volumetric flow rate (which occurs in most pipe flow problems) the smaller the cross-sectional area, the greater the flow velocity. Isolating the best answer will require a bit of math. Let's use the continuity equation (7.25) to find the final flow velocity. We get:
-=fe)^Br=&r=((#h=W(05m/s)
Looking at the choices left, choice D looks like the likelier of the two answers. If you're doubtful, realize that (16/9) is a bit smaller than 2, which makes the
irr?
answer a bit smaller than 1.If you forgot to square the radii, you probably picked choice C. There will often be an answerchoice on the test for eachcommon way
of misinterpreting or miscalculatinga problem. Please be careful.
The best answer is choice D.
Example 7.8b
The plunger ofa hypodermic syringe has a cross-sectional areaof approximately 0.5 cm2, whereas the attaching needle hasa cross-sectional area of0.005 cm2. If a doctor (you in five or six years) pushes in the plunger at a speed of 0.3 cm/s, what is the average flow speed ofthe medicine through the needle?
A. B. C. D. 0.003 cm/s 30 cm/s 300 cm/s 3000 cm/s
Solution
This question involves the continuity equation, which relates the average flow speed and cross-sectional area at two different points in a pipe. The relationship
is Aivi = A2v2. Manipulating the equation shows us that the as the as the crosssectional area decreases, the average flow speed has to increase by the same factor. In the syringe example, the cross-sectional area decreases by a factor of 100, so the average flow speed must increase by a factor of 100. This means that the average flow speed will increasefrom 0.3cm/s to 30 cm/s.
The best answer is choice B.
72
Physics
Bernoulli's Equation
Fluids in Motion
Consider a pipe filled with an incompressible, ideal fluid. As we noted earlier, a fluid flows when it has unequal pressures applied to it, flowing from a region of higher pressure to a region of lower pressure. Let's consider the higher pressure to be Pi and the lower pressure to be P2, and that the two pressures represent the pressure at the two ends of the pipe. As the fluid moves, its kinetic and gravitational potentialenergies change. This is due to the work done on the fluid by the pressure difference pushing the fluid in one direction. These energy changes are related to one another by the work-energy relationship shown in equation (7.25). In this equation, W is the work done on the systemby pressures
Pi and P2, AKE is the kinetic energy change, and APEg is the change in
gravitational potential energy.
W = AKE + APE
g
(7.25)
We shall consider these three aspects (work done on the fluid, kinetic energy of
the fluid, and gravitational potential energy of the fluid) separately using the pipe shown in Figure 7-9. In this pipe, there is both an elevation change and a change in radius. What we shall consider is the pressure exerted by the fluid against the inside walls of the pipe. Whether the fluid flows left-to-right or rightto-left, the same result will be obtained.
Region 1
r
'
Region 2
1
Region 3
i s
/
;\.
Pi"
. . . .
...L...r... p.
: > i
/ /
i i
N
v2
V
yi !
y 1f
h = yi
: 1'
n T: Pagainst wall *
Let's consider work first. If the fluid moves a distance Axi on the left side of the
vessel, then it must move a distance Ax2 on the right side of the vessel. Recall that
W= Fj.(Ax). Ifweapply thisexpression to thefluid moving in the vessel, thenwe get equation (7.26). Given that Fi = PiA and F2 = P2A, making the appropriate substitution into equation (7.26) gives equation (7.27). The volume of fluid that
moves from left to right in the vessel is the same. So, AV = AiAxi = A2AX2. Substituting this information into equation(7.27) gives equation (7.28):
W = FiAxi - F2AX2
(7.26)
(7.27)
(7.28)
We're doing this math to work our way to Bernoulli's equation, which relates
pressuresin the way the work energy theorem relates energy terms.
Copyright by The Berkeley Review
73
PhysiCS
Fluids in Motion
Now lefs consider the change in kinetic energy for the flowing fluid. By manipulating the relationship p = m/V, we solve this expression for the mass of the fluid to show that m = pV. The change in kinetic energy for the mass of a moving fluid is given by equation (7.29). Substitution of pV for m into (7.29) gives equation (730):
(7.29)
(7.30)
In Figure 7-9, the fluid has moved from yi to y2overall. Therefore, the change in
gravitational potential energy can be given by equation (7.31). Substitution of m = pV into equation (7.31) gives equation (7.32):
(7.31)
APEg = (pV)g(y2-yi)
(7.32)
We are now in a position to substitute equations (7.28), (7.30), and (732) into
equation (7.25). After we divide through by V, we will get equation (7.33). This equation can be applied to a fluid that is incompressible, is frictionless, and has laminar flow. We can rearrange equation (7.33) to look like equation (734). This is the more common form ofBernoulli's equation:
(7.33)
(7.34)
As you view Bernoulli's equation it is unlikely that you are thinking, "wow, what a great equation. I can't wait touse it." Atface value, the equation does not look friendly, sowe shall rewrite it ina more user-friendly format. Equation (7.35) is a more conceptual rewrite thatwill allow us to compare the impact ofvarious changes on thepressure ofa moving fluid against theinnerwalls ofa vessel.
(7.35)
This version of the equation can explain some of the phenomena you may have observed in life such as the bottom of a shower curtain attacking your ankles when you turn the water on or your bike getting sucked towards a passing bus.
shower. As it falls, it picks up a good deal ofspeed (being that it's in free fall). According to equation (735), as v goes up and h barely changes, the pressure against the walls (in this case the shower curtain) must drop. The water is fastest near the bottom of the shower curtain, so it is pushed towards your ankles by the higher air pressure outside the shower. As soon as you turn the water off, the
When you turn the water on, it falls from the shower head to the bottom of the
This also explains why rolling down the windows of a moving car generates
airflow. When the window is opened, the rapid airflow outside the caracross the openspace where the glass used to be creates a lower pressure outside of thecar window. This causes airinside the car toflow out, thereby helping tocool the car
A common example of Bernoulli's principle applied to engineering involves air foils such as airplane wings, where pressure differences between above and
below the wing can cause a plane tolift off ofthe ground at high speed.
74
Physics
Fluids in Motion
In the case of an airplane wing, as the wing moves through the air, the surrounding air must pass either across the top of the wing or across the bottom of the wing. A wing (or air foil as it is more formally called)is designed in such a way that the top and bottom are asymmetric, resulting in different airflow dynamics on the two sides of the wing. The top of the wing is curved in such a way that it is longer than the bottom, so if we compare the paths an air molecule would take during the period of time when the wing passes by, it must move faster to pass across the top of the wing than it would passing along the bottom of the wing. According to equation (735), a higher speed results in a lower pressure along the surface if the wing. In essence, the air molecules by moving faster have fewer opportunities to collide with the surface of the wing. The result is a net force upward, which adds to the overall lift force on the wing. The total lift force on the wing involves the angle of the wing as well as the difference in air pressure due to air movement. This can be viewed in Figure7-10.
Conclusion: As vair | :Pagainst wing A' Greater vair => Lower Pagainst wing
Figure 7-10
While you are stopped at an intersection turn lane, a large truckzoomsby, just a few feet fromyour car. As the truck passes,your car willbe:
Example 7.9a
A. pulled towards the truck, because the increased wind speed between the
B. pushed away from the truck, because theincreased wind speed between the C. pulled towards the truck, because the increased wind speed between the D. pushed away from the truck, because the increased wind speed between the
truck and the car increases the pressure there.
Solution
This is a qualitative type ofquestion, and you have to consider the local pressure
on each side of the car. As the truck zooms by, the air in front of the truck is
pushed out ofthe way, resulting in a wall ofair rushing by yourcaron the side of the truck. We can see from equation (735) that as the speed of the air increases, theforce it exerts against the side of the carwill be reduced. Asa result, there is a higher pressure against the side of the car opposite of thezooming truckthan the
side of the car closestto the zooming truck. The result is that the car is pushed in the direction of the truck (which feels like you are being pulled towards the truck). This eliminates choices B and D. The air speed causes a drop in the local pressure againstthe side of the car,so choice C is eliminated.
The best answer is choice A.
75
PhysiCS
Fluids in Motion
When blood flows through an artery, it exerts pressure on the surrounding arterial wall. Compared to a section of healthy artery of equal size, a narrowed section of diseased artery experiences a pressure on the surrounding arterial wall
that is:
A. B. C. D.
greater, becausethe flow velocity decreases. greater, because the flow velocity increases. smaller, because the flow velocity decreases. smaller, because the flow velocity increases.
Solution
This is a qualitative type of question, and you have two concepts to consider: the local pressure and the blood flow velocity. Consider first the concept you understand the best. For example, will blood-flow speed increase or decrease when blood traverses a narrow region of an artery? It should flow faster (from the continuity equation (7.23)). This rules out choices A and C. Next, will the pressure increase or decrease when the blood velocity increases? It should decrease (from Bernoulli's equation (734)). These two equations are the most important flow equations for the physics you'll do, and should therefore be at least qualitatively understood. It might even be a good idea to commit them to memory. By the way, the correct answer is choice D.
afflicted with atherosclerosis pumps with a greater pressure to keep the blood volumetric flow rate at healthy levels, increasing the total pressure throughout the arteries. However, the pressure is lower in an unhealthy section ofan artery than it is in a nearby healthy section because of the increased flow speed. This comparison was thethrust ofthis question. As an aside, the lower pressure in the
narrowing artery can be low enough to do more than offset the increased pumping pressure of the heart, making the arterial pressure lower than that in a
You may have incorrectly assumed that the pressure should increase because of the "high blood pressure" associated with atherosclerosis. The heart of one
Turbulence
have the ability to slide past one another in a smooth and uniform fashion (see
sufficiently high, then a chaotic and irregular pattern develops in the fluid. This is called turbulent flow. Viscous frictional forces increase duringturbulent flow.
Figure 7-6). This type of flow is laminar flow. It is also called streamline flow. Poiseuille's principle holds true only for laminar flow. If the flow of a fluid is
this. The Reynolds number isdefined by equation (736), where pis the density, r\
is the viscosity, and Vis theaverage velocity of the fluid. The radius of the vessel through which thefluid flows is givenby R.
(7.36)
In general, if Nr < 2000, then the flow is considered to be laminar. If Nr > 3000,
the flow is turbulent. Between 2000and 3000, the flow is said to be unstable. This
76
Physics
Example 7.10a
Fluids in Motion
Which of the following will decrease the chance of turbulent blood flow in a
vein?
A. B.
C.
D.
Widening the vein while maintaining the same flow speed. Thinning the blood without changing its density. Increasing the absolute pressure on each end of the vein by the same
amount.
Solution
You can apply the Reynolds number equation to each choice, crossing out
choices that either increase the chance of turbulence or leave that chance
unchanged. Choice A widens the vein and increases the Reynolds number. This will increase the chance of turbulent flow, making it an incorrect choice.
One way to remember this relationship is to watch smoke rising from a candle. As it leaves the candle, it flows upward in a smooth (non-turbulent) narrow band. This band widens as it rises and becomes turbulent. So, narrow paths (or objects) are less likely to encounter turbulence. Wider paths (or objects) are more likely to do so. Choice B lowers blood's viscosity, increasing the Reynolds number. This will make turbulence more likely. Choice B is incorrect. Choice C creates a greaterpressure everywhere around the vein, but this changes nothing. The onset of turbulence depends upon a sufficiently large flow rate. Flow rate in turn depends upon a pressure difference. If that difference does not change, the flow rate does not change.This rules out choice C, leavingonly choice D.
If this were the MCAT, you'd now move on to the next problem. However, if
you'd like to know why D is correct, then notice that lowering theblood density
would decrease the Reynolds number. This means that turbulence is less likely. Odds are good that the passage text would contain an equation as uncommon and unattractive as the Reynolds number equation. In fact, any time you are
Example 7.10b
Which of the following will increase the possibility of turbulent airflow around the wings of an airborne plane? (Assume the basic shape of the wing does not changeand that all dimensions are proportional.)
A. B. C. D. Flying at faster speeds and using larger wings. Flying at slower speeds and using larger wings. Flying at faster speeds and using smaller wings. Flyingat slower speeds and using smaller wings.
Solution
You can apply the Reynolds number equation to each choice, and determine which will raise the value of Nr. The value of Nr increases with fluid speed, so choices B and D can be eliminated. As the wings get bigger, the region in which the air flows around the wing increases. An increase in that area means that the R has increased, so Nr gets larger. This eliminates choice C.
The best answer is choice A.
77
Physics
Solids
Solids
They have a regular ordering of their constituent atoms. Solids usually have a
well-defined melting temperature.
Density
As we stated in the section on fluids, the density of a material is defined as its mass per unit volume (see equation (7-1)). Densities vary with temperature as well as with pressure. Note from the data in Table 7-1 that the density of a solid is (generally) greater than the density of either a liquid or a gas.
The stressa is defined as a force acting on a solid divided by the area on which the force is acting. This is given by equation (737). The SI unit of stress is the
N/m2. The three common types of stress are tension stress, compression stress,
and shear stress.
(737)
The strain Eis the fractional change in length of a solid and is a measure of the deformation caused by a stress. This is given by equation (738). Note that the strain is a dimensionless number and does not depend on the original length of thesolid, only on the fraction by which thelength changes
Strain = e
(738)
In Figure 7-11 is a plot of the strain versus the stress in a solid. Note that for
small values of the strain, the graph is a straight line. This is telling us that the stressis linearly proportional to the strain in that regionof the graph, sometimes
referred to as the linear region. For larger values, we find that the stress is no longer proportional to the strain. Just past the linear region we encounter the elastic limit of the solid. If the force causing the deformation is removed when
the material has reached its elastic limit, then the material can still return to its original shape. In other words, the deformation of the material has been elastic.
A material is plastically deformed once it passes its elastic limit Any point past the elastic limitresults in covalent bond breakage of the solid lattice structure. If strain increases, we reach the material's ultimate tension strength, at which point the material is under maximum stress. If strain is increased beyond this point, the stress on the material becomes reduced and eventually the material will fracture. Once a fracture has occurred, the material has been plastically
deformed, and it will not return to its original shape.
Copyright by The Berkeley Review
The Berkeley Review
78
Physics
Solids
strength
Elastic y limitX
Fracture
0
l/l (A
IS cr>
/6
/>
/$
Strain (e)
Figure 7-11
Materialsthat have ultimate tension strengths close in size to their fracture stress are often called brittle. They have a tendency to fracture, without deforming much. You see this when breaking a saltine cracker or snapping a strand of dry
spaghetti. Materials that have fracture strains far above their ultimate tension
or stretching a rubber band.
strength are said to be ductile. Beyond the ultimate tension strength, they will deform noticeably before fracturing. You see this when pulling on chewing gum In Figure 7-11, the slope of the linear region is the stress divided by the strain.
This is called the Young's modulus Y of the solid and is given by equation (739).
Young's modulus is the proportionality constant that relates the stress to the
strain. It is sometimes referred to as the modulus of elasticity, E.
E = Y = Stress _ a _ F/A
Strain e AL/L
(739)
Example 7.11a
Fora rope experiencing a constantapplied force, all of the following changeswill decrease the stretching length of the rope EXCEPT:
I. usinga shorter rope made from the same material. II. using a thinner rope made from the same material. HI. using a rope of similar size and with an equal value of Young's modulus.
A. I and II only B. I and III only C. II and in only
D. I, H, and in
Solution
This is a particularly difficult question not because of the concepts, but because of the ease with which you can make a careless error. Lefs use physical intuition and then the relevant stress-strain equation to solve this problem. We want to know which changes will either increase or leave unchanged the absolute length the rope stretches.
Regarding Statement I, a shorter rope has less material to stretch (deform), so under identical forces, a shorter rope will not stretch as far as a longer rope of equal radius and the same material. This results in a decrease in the length, so
Statement I should not be in the answer. This eliminates all choices except C.
79
Physics
Solids
Regarding Statement II, thicker ropes are usually used for heavier loadsStatement II and eliminates choice B.
presumably tokeep the rope from stretching and breaking. Therefore, switching
to a thinner rope should increase the stretching length of the rope. This supports
Statement HI should leave the rope length unchanged. After all, that depends upon the size of the rope and its elasticity (which Young's modulus characterizes). Since neither one changes, Statement III must be true, and choice
A must be incorrect.
To verify our conceptual choice, lefs use the stress-strain relationship described by equation (739). Solving for the stretching distance AL:
AL = L
AY
Using a shorter rope decreases L, which will decrease ALremember, the other
variables are held constant for Statement I. This confirms that Statement I was
correctly ruled out. Using a thinner rope decreases A, which will increase AL; that supports StatementII. Finally, using a rope of equal size and equal elasticity (i.e., of the same Young's modulus) will not change AL; this validates Statement III and points to choice C. There are many ways to answer a question-two ways are using physical intuition and looking for the basic relationship in equations. In
using equations, remember that they always tell you the relevant conceptual
physics of the question.
The best answer is choice C.
Example 7.11b
Which of the following changes to a cable will increase the chance that the cable will stretch to a point where it irreversibly deforms?
A. Make the cable thicker.
First off, considering we are concerned with stretching the cable, a compression force is not applicable. Choice B can be eliminated immediately. A material stretches beyond its elastic limit when a threshold stress is exceeded, causing a strain so great that the material permanently deforms. This basically means that the AL is too great for the material to relaxback to its original state once the force
is removed. A thicker cable is harder to stretch, so choice A will reduce the
80
Physics
Bulk and Shear Deformation
Solids
Bulk stress and bulk strain are different from the compressive and tensile stresses and strain we considered with Young's Modulus, because now the force on the object is being applied on all sides, so it deforms in all directions rather than just one. Bulk deformation results in a change in the volume of an object. It is often encountered when an objectis submerged deep into a body of water, such as the ocean. The volume strain is shown in equation (7.40), where AV is the change in volume and V0 is the initial volume of the solid object
Volume strain =
AV
(7.40)
This can be applied to measure the bulk modulus, B, of an object. The bulk modulus of an object relates how much the volume of a solid object changes as the pressure surrounding it changes. It can be calculated usingequation (7.41).
B =
AP
AV/
A Vo
(7.41)
/y
Compression = AV
Figure 7-12
objecfs walls. When a force acting parallel to a surface ofa solid object is strong
But when a force is applied parallel to the layers, it breaks rather easily, as we see
occurs when one layer slides across another layer in a material. Certain materials, such as graphite, are prone to shear because their crystalline structure is one of layers. Graphite is used to reinforce many structures inone dimension, because it is lightweight and strong in the direction perpendicular to its crystal layering.
enough, there is the chance for a third type of deformation know as shear. This
with pencil lead. While there are equations for shear, we shall only consider the concept Figure 7-13 shows a basic view ofa solid undergoing a lateral shearing
force.
81
Physics
Solids
'l
t = 0
t = l
t = 2
Figure 7-13
Example 7.12a
Solution
can eliminate choices A and D immediately, because they are liquids. Based on your real life experiences you have no doubt come to learn that it is easy to
Steel has the greatest bulk modulus.
The best answer is choice C.
compress a rubber item, but steel is sturdy and can withstand great stresses.
Example 7.12b
When a stack of papers is placed on a sloped table, the top papers sometimes slide off of the bottom papers, which remain stationary. This is an example of:
A. bulk deformation. B. shear deformation.
C. gravitational distortion.
D. tensile deformation.
Solution
deformation involves a change in the volume of an object due to a change in the external pressure on the object. Tensile deformation involves linear stretching of
gravitational distortion, so choice Cshould have been eliminated immediately.
The best answer is choice B.
82
I.
II. III.
Hydraulic Press
Relax and Float Stress and Strain
The main purpose of this 25-question set is to serve as a review of the material presented in the chapter. Do not worry about the timing for these questions. Focus on learning. Once you complete these questions, grade them using the answer key. For any question you missed, repeat it and write down your thought process. Then grade the questions you repeated and thoroughly read the answer
explanation. Compare your thought process to the answer explanation and assess whether you missed the question because of a careless error (such as misreading the question), because of an error in reasoning, or because you were missing information. Your goal is to fill in any informational gaps and solidify your reasoning before you begin your practice exam for this section. Preparing for the MCAT is best done in stages. This first stage is meant to help you evaluate how
well you know this subject matter.
Passage I (Questions 1 - 7)
A hydraulic press is an ingenious device that allows the lifting of heavy objects by the application of a small force to a small piston. A basic schematic of a hydraulic press is
shown below:
4.
F2
=4=~<3 Ah2
Piston 2
A^ r
Piston 1
5.
Which of the following changes will NOT decrease the average time it takes the hydraulic press to pass back through its equilibrium position, if Piston 1 is subjected to a briefly applied external force that is subsequently
released?
A force Fj is applied to Piston 1.This creates a pressure Pj on Piston 1, which increases the pressure uniformly
throughout the much larger oil reservoir and results in a force
III.
A. B. C. D.
A. F2= F1
B. Fo>F 1
6.
C. P2= P!
D. P!>P2
Fj and F2.
A. energy is not conserved for this process. B. momentum is not conserved for this process. C. forces are conserved for this process.
D. none of the above.
7.
3.
A. B. C. D.
Both Pj andP2would increase. Pj would increase; P2would remain thesame. P2 would increase; Pj would remain thesame. Pj and P2would be unaffected.
C. x2 =xl
1 5
D. x2 =xl
1 25
84
Passage II (Questions 8 -14) Whether an object is submerged completely in a fluid or whether it floats on the surface, it experiences a buoyant force. Buoyant force is the force of the fluid on the object; it results from pressure differences. The buoyant force is:
10. Three objects are placed in a tank of water, as shown below. The objects all have the same size, but they have different densities: pj < pn < prrj < pwater-
B = Pfluid'Vdisplaced fluid'g
A researcher sets up an experiment: A wooden box of cross-sectional area A and density p floats on the surface of a fluid, so that a length L of the box is submerged (Figure la). A force F is then applied to the top of the box, so that now an additional length x of the box is submerged (Figure lb).
Ql
A. B. Object I Object II
On
Om
If all of the objects are released at the same time, which object reaches the surface first?
(a)
C.
Object III
2S
MZ
11. Fluid
If salt is added to water, the water density increases. The force needed to submerge a floating, completely incompressible object will:
A. increase as the density increases and increase slightly as the submersion depth increases.
Figure 1 B.
The force F is removed and the box bobs as a simple harmonic oscillator, where the acceleration a, displacement
increase as the density increases and decrease slightly as the submersion depth increases. decrease as the density increases and increase slightly as the submersion depth increases.
C.
a = -4ji2/2x
Neglect the effects of fluid viscosity in these questions.
8. The three tanks shown below contain objects of the same size and density, at the same depth in each tank. Which object experiences the GREATEST pressure?
D. decrease as the density increases and decrease slightly as the submersion depth increases.
II
12. Three objects with the same density but different sizes are placed in a tank of water as shown below:
"
A. Object I B.
C.
Object II
Object III
si
II
After the objects are released: A. Object I has the greatest acceleration. B. Object II has the greatest acceleration.
9.
Buoyant force is always equal to the: A. weight of the object. B. weight of the fluid displaced.
C. volume of the object. D. volume of the fluid displaced.
C. Object III has the greatest acceleration. D. All three objects will have the same acceleration.
85
II. local water density increases slightly, due to the weight of water above that location.
A. Both I and II increase the magnitude of the buoyant force on the object B. Both I and II decrease the magnitude of the buoyant force on the object C. Only Statement I increases the magnitude of the buoyant force on the object D. Only Statement II increases the magnitude of the buoyant force on the object
F/A
where F is the force applied to an object and A is the crosssectional area that experiences the force. Three stresses are commonly defined: tension stress, which elongate an object; compression stress, which compresses an object; and shear stress, which is the application of scissors-like forces. The deformations produced are called strains. Strains are fractional changes in lengths:
L
Stress and strain are linearly related (over a given range of stresses) by Young's modulus, a material's physical
property:
14.
In the experiment described in the passage, what is the frequency of oscillation of the box?
A.
Y = 2
E
In V PboxL
Pfluid g
B. -L.
C.
vs
g_
X
Table 1 lists Young's moduli for various materials, as well as their ultimate tension stresses and ultimate compression stresses (the maximum stress that a material can tolerate):
Material
Aluminum Steel Glass Brass
1 J
Pbox
2n V L + x
D.
2xl08
5xl08 5xl07
2xl08
5 xlO8
not measured
1 WPftuidg"
2ji V AL
2.5 x 108
not measured
2.5 x 108
not measured
Copper
Concrete Bone
9.7 x 1010
not measured
2xl07
1.6 xlO10
1.7 x 108
A group of students decide to study the relationship between stress and strain. They do two experiments.
Experiment J
Scale
After Load
40N
50 N
Scale
Reading
4.000 cm 4.032 cm
Reading
4.128 cm 4.160 cm
4.192 cm
4.064 cm
4.096 cm
60 N
70 N
30 N
4.224 cm
Table 2
86
Experiment2
19.
What was
the
maximum stress in
the
wire
in
Students observe the mechanical properties of thin rods of equal size, constructed from either concrete, brass, or steel. The rods either support loads at their middle sections when oriented horizontally, or loads at their upper end when oriented vertically.
15. Which material requires the SMALLEST applied stress
to have a 5% strain?
A. Steel
Experiment 1?
A. 7x 10!N/m2
B. Copper
C.
D.
Aluminum
Bone
20. When comparing the ultimate compression and the ultimate tension strengths given in the passage:
A. the two values are always equal. B. the ultimate compression strength are always larger
than the ultimate tension strength.
0.032
0.224
21.
17.
B. when horizontal, all three materials could support the same maximum weight. C. when vertical, steel supported more weight than
brass or concrete.
D. when vertical, brass and steel could support the same maximum weight.
18.
Further experimentation measured strains for much higher stresses than those reported in Experiment 1. As
the data plotted below became non-linear:
Strain (e)
87
25.
To make the pressure in Region 1 equal to the pressure in Region 3, what can be done?
Region 1
1 1
1
Region 2
Region 3
22.
What will be observed when a more viscous liquid, of the same mass density, is substituted for the less viscous liquid in the system below?
Reservoir Column 1
1
1
i
1
k
i^
yi
1
/
A
y2
:
\
1 1
1
:
y3!
1 1
1
! _-:
I. Increase yi
III.
Decrease y3
A. A greater fluid velocity at point B, but an unchanged fluid height in Column 1. B. A greater fluid velocity at point B, and a greater
fluid height in Column 1.
A. I only B. HI only
C.
D.
Either I or II
Either I or III
C. A lower fluid velocity at point B, but an unchanged fluid height in Column 1. D. A lower fluid velocity at point B and a greater fluid height in Column 1.
23.
Comparing the average blood pressure in similar veins in the neck and calves of a standing human reveals that the blood pressure will:
A. be greater in the neck. B. be greater in the calves. C. be the same in both places.
24. As blood flows steadily through a pipe of uniform cross-section and length L, its speed:
A. must increase to counteract losses to viscosity. B. must decrease to counteract losses to viscosity.
2. 7. 12.
D D D
3. D 8
D
4.
9.
B B
5.
6. A 11. A
10. A 15. D
13. D 18.
23. B B
14. A
19. D
16. A
21. C
17. C
22. C
20. D 25. D
24. D
88
Hydraulic Press
Choice C is the best answer. Pascal's principle states that a pressure change applied to any point of a contained fluid is
transmitted undiminished in all directions to every point inside that fluid. If a pressure change Pj is applied to a contained fluid by Piston 1, then this pressure change is felt uniformly everywhere inside that fluid. P2 must equal Pj, which means:
^1 = ^2.
A, A2
Because the surface areas of each piston are different, while they both share the same force/area, the forces must be different.
The force on the large piston surface is greater than the force on thesmaller piston surface, meaning that F2 is in fact greater than Fj. However, that is merely an observation and not a reason for the difference in force magnitudes. Choice B is
incorrect, because the question asks for the cause of the force difference; choice B merely repeats the question. Choices A and D are incorrect relationships. The best answer is choice C.
2.
Choice D is the best answer. Although a hydraulic press makes it possible to produce a large force upon the application of a small force, no physical laws are being violated. If the fluid is incompressible, then the work applied on one side is equal to work acting on the other side. Energy is conserved, so choice A is eliminated. The fluid moves when the piston is put into
motion, which in turn moves the other piston by a distance that is proportional to their relative sizes. This follows conservation of momentum, so choice B is eliminated. The force is different on each side of each piston, because their surface areas are different, so the force is not conserved. Choice C is eliminated. By default, the best answer is choice D.
3.
Choice D is the best answer. By conservation of energy, the work done on Piston 1 must equal the work done on Piston 2. Work is the product of force and displacement, so we can say:
Fjx, =F2x2
Since r2 =5rj and since A= jtr2, A2 =25A j.That means that F2 =25Fj, so x2 must be -L. The best answer is choice D.
4. Choice B is the best answer. From the equation:
Aj
A2
vve see that in order to increase F2 by a factor of 4, we must increase Fj by a factor of 4, increase A2 by a factor of 4, or
decrease Aj by a factor of4. Since A = jtr2, then in order to increase A2 by a factor of4, we must increase r2 by a factor of
2. In order to decrease A j by a factor of 4, we must decrease rj by a factor of 2. The best answer is choice B.
5. Choice C is the best answer. We want to know which changes will NOT decrease the time for the pistons to pass back
through their equilibrium positions. We must find which choices either increase or do not affect this time. Decreasing oil viscosity would allow the oil to flow more freely and the pistons to move more easily, and therefore more quickly, towards equilibrium. This invalidates Option I and eliminates choices A and D. Of the remaining choices, vve need consider only Option III, because Option II is in both of the remaining choices. Increasing the volume of the reservoir does not affect how fast the pistons move. From the passage, vve know that the reservoir is substantially larger than the piston columns. Therefore, the flow of oil from Column 2 to Column 1 is not affected much by an increase in reservoir oil volume. This validates Option III, making choice C the best answer. Let's consider Option II. Increasing the mass of Piston 1 increases the gravitational force which, in turn, leads to a smaller acceleration of Piston 1 back up towards equilibrium. The gravitational force here acts in the same direction as the force initially applied to Piston 1. The same can be said for Piston 2 moving in the opposite direction. The basic idea is that heavier pistons move more slowly than lighter pistons. This will increase the time
towards equilibrium, validating Option II. The best answer is choice C.
6.
Choice A is the best answer. The hydraulic press works when one piston is pushed in towards the oil reservoir by any kind of force, which in turn presses outward against the other piston. This process requires only that the oil be there, not that any gravity be present. Because the press does not need gravity, choices B and D are incorrect. Choice C is incorrect, because the pressure must be equal throughout the reservoir. If the pressure varied, there would be a continuous flow of oil towards the side with lower pressure until the pressures were uniform. The principle behind this is often referred to as Pascal's principle.
The best answer is choice A.
89
MINI-TEST EXPLANATIONS
7.
Choice D is the best answer. Pressure is defined as force/area. Changing the density of the fluid will not change the cross-
sectional areas of the pistons, and it will not change the magnitude of the force applied to Piston 1. If:
Pl = p2 => El=Ei
A, A2
Choice D is the best answer. Although the three tanks have three different shapes, the height of the fluid in all three cases is the same. Pressure at a depth h below the surface of the fluid is pgh. Since the objects are all at the same depth h, they all
right answerfrom the equation for buoyant force given in the passage:
B = Pfluid'Vdisplaced fluid'g
Density and volume are related by mass:
B=massdispiaced fluid'g. so, the buoyant force is equivalent to the weight ofthe fluid displaced. The best answer ischoice B.
10. Choice A is the best answer. Acceleration depends on the density of the object. An object with a smaller density will have a
greater acceleration. If the objects are all released at the same time, then Object I will reach the surface First. The best
answer is choice A.
11.
Choice A is the best answer. If the fluid density increases, the buoyant force formula in the passage indicates that the buoyant force will increase. This means that more force is needed to submerge the object, in order to overcome the buoyant force. This rules out choices C and D. As the submersion depth increases, more force will be needed to get the object to that lower depth. Why? As depth increases, so does the local density of the fluid. Fluids, even water, are slightly compressible. The increased pressure at lower depths compresses the liquid lightly. This increases the buoyant force against the object. Normally, the object would also compress somewhat, complicating matters; but this object is said to be completely incompressible. The best answer is choice A. Choice D is the best answer. Because the objects each have a density less than that of water and are completely submerged, the buoyant force acting on the objects is greater than the weights of the objects. There will be a net force upwards on each object, so they will rise. Consider the free body diagram for any one of the objects:
12.
where B = pwater^objectg ana" the weight of the object can be written as:
mg = Pobject Vobject 8
Note that because the object is completely submerged, the volume of the object and the volume of displaced fluid are equal. The difference between these two forces gives us the net force acting on the object. Solving for acceleration:
ma = B - mg
_ V object v i
or
ma = (pwater'Vobjecfg) - (PobjecfVobjecfg)
g(p
wate m
The acceleration of each object is independent of its volume (size), but depends on the density of the object. If all of the objects have the same density, they all have the same acceleration. If the objects are all released at the same time, they will all reach the surface at the same time. If this seems long-winded, then just remember that objects with the same density are subjected to the same buoyant acceleration in a fluid. The best answer is choice D.
90
MINI-TEST EXPLANATIONS
13.
Choice D is the best answer. Both statements describe ways in which the object's density increases as it is submerged intoa tank of water. The object's mass cannot change, as it neither gains nor loses matter, so the increase in density is associated with a reduction in the object's volume. Decreasingthe object's volume decreases the buoyant force on it, by decreasing the volumeof fluid displaced by the object. This invalidates choices A and C. Having a larger water density, on the other hand,
would increase the buoyant force, as seen in the buoyant force equation given in the passage. The best answer is choice D.
14.
Choice A is the best answer. Solve for frequency, using the equation given in the passage:
/ =
=74A
where the minus sign has been dropped, since the magnitude of frequency depends only upon the magnitude of the acceleration. Plus and minus signs generally indicate direction, not magnitude. Let's use this equation and physical intuition to choose the best answer. The acceleration in the numerator means that more acceleration will increase the frequency. Gravity is one force accelerating the box (through mg and the buoyant force); we therefore expect that the gravitational
acceleration g should be in the answer. This rules out choice C. Furthermore, the units should be those of acceleration
divided by length, which rules out choices B and D. This leaves only choice A, which looks curiously similar to the oscillation frequency of a pendulum of length L. Notice that the oscillation frequency would increase, if the box were made
less dense than the fluid. What happens to the frequency when the density of the box exceeds that of the fluid? The box no longer has a frequency, and it sinks. The best answer is choice A.
Passage III
15.
(Questions 15 - 21)
Choice D is the best answer. The material requiring the least stress for a given 5% strain must be the material with the
smallest value of Young's modulus:
Y = 2
8
where o is the applied stress and e is the resulting strain. From the data given in the passage, bone has the smallest modulus, making choice D the best answer. This is why they use metal, which is stronger than bone, to hold shattered bones together, and why they do not use bone to hold together fractured metal. The best answer is choice D.
16.
Choice A is the best answer. The maximum strain in the wire occurs with the maximum force, 70 newtons. The change in
the wire's length of the wire with the application of this force is 0.224 cm, so the strain is:
e =
AL
0.224 x 10-2 m
5 m
17.
Choice C is the best answer. The wire is made of steel, so the maximum load by using the ultimate tension strength is:
aT= rmax
40x 101 is slightly overestimated, because 7.85 isless than 8. Looking at the possible choices, choice C seems to be the best.
Doing the arithmetic completely will confirm this; but you have only 1.29 minutes to answer each question, which makes doing complete arithmetic a complete waste of time. Always use the four answer choices to reduce your arithmetic (e.g., ask yourself if 5 x 7.85 looks more like 3.5,27.5, 39.3, or 48.0). The best answer is choice C.
18.
Choice B is the best answer. As the nonlinear region of the graph begins, it takes very little stress to strain (stretch) the wire. That is what the flattening of the curve represents. If you have ever pulled on one a wad of chewing gum as you were biting on the other end, you know that at some value of stress, the gum begins to stretch very easily. Beyond this point, the gum will never elastically rebound to its original shape; it has permanently deformed. This points towards choice B. Choice A is incorrect, because the wire stretches when any stress is put on itremember, stress gives strain. Stretching alone would not explain the bend in the plotted data. Choices C and D say essentially the same thing-stiffer materials have a bigger Young's
modulus. This invalidates both choices C and D, leaving only choice B. The best answer is choice B.
19.
Choice D is the best answer. To find the maximum stress, we use the maximum applied force, 70 newtons:
0= F =
Since 70/7.85 is between 1 and 10, the order of magnitude of the answer must be 107, making choice D optimal. Do not
waste time by doing the division. Just convince yourself that the answer is between 1 and 10. The best answer is choice D.
91
MINI-TEST EXPLANATIONS
20.
Choice D is the best answer. An applied stress is opposed by intermolecular forces within the material. If the composition
of the material is not homogeneous, these intermolecular forces are not equal for tension and compression. This points to
choice D as the best answer. Choice C is incorrect, because most of the numbers reported in the table are strikingly similar.
For two independent quantities, you should generally expect unrelated numbers. Choices A and B are wrong for two reasons: There are missing data trends in the tables, which precludes verifying any general relationship; and the data for bone have
different values for the ultimate tension and compression strengths. When encountering an "always" or "never" choice, just
look for or think of one example that invalidates the choice-more often than not, there is at least one. The best answer is
choice D.
21.
Choice C is the best answer. When oriented vertically, the compression strength will dictate how much weight a given rod can withstand. From the table given in the passage, steel has the highest compression strength of the three materials. Thus,
steel can support the most weight; choice C is correct. Choices A and B are wrong, as you know if you have ever seen a building under construction. For horizontal concrete beams, there are always steel rods within the concrete. These rods are there for support, implying that steel is better than concrete in this horizontal orientation. Why not make all the horizontal
beams out of steel? Two reasons are: First, the building would become unreasonably heavy, requiring even more vertical
support; and second, steel costs more than concrete. The best answer is choice C.
Questions 22 - 25
22.
Choice C is the best answer. The fluid velocity will decrease if a more viscous liquid is used, assuming that all other conditions remain the same. This can be deduced from the definition of viscosity, which is the resistance to flow. We can eliminate choices A and B. The fluid heights in the columns depends upon the pressure below each column in the drainage
tube. The pressure difference across the drainage tube depends upon the pressure at the reservoir end (which is due to the weight of the fluid) and the pressure at the exit end (which is due to the atmosphere). Since neither pressure changes, the
introduction of the new fluid (whose mass density is equal to that of the previous fluid) will not affect the fluid heights in the
columns. The best answer is choice C.
23.
Choice B is the best answer. Although blood is a viscous fluid, the effects of viscosity are small on it, and we can approximate the blood as an incompressible, nonviscous fluid. This means that Bernoulli's equation is applicable: P + pgh + -pv = constant If vve compare similar veins, then the flow velocity through them should be somewhat similar. Thus, any blood pressure difference between them arises from blood pressure being measured at different elevations separated by a distance h. Since the calves are closer to the ground than the neck, in a standing human being the calves experience a greater average pressure. This is why an open wound is elevated to reduce bleeding, and it makes choice B the best answer. Choice D is invalid, because any average changes in the blood pressure produce similar changes in the neck and calves. The best answer is
choice B.
24.
Choice D is the best answer. As blood flows steadily through a pipe of uniform cross-section and length L, its speed remains constant, as long as the pressure difference between the ends of the pipe is constant. The best way to answer this is to eliminate the three incorrect choices. The question stated that the blood flows steadily, which means Q is a constant. But we also know that Q = Av. The pipe has a uniform cross-section, which means A is a constant. This all implies that v, the speed of the fluid, is also a constant. Choices A, B, and C all say that the speed changes, so they must be incorrect. The best
answer is choice D.
25.
Choice D is the best answer. Comparing pressures between two different regions requires employing Bernoulli's equation. Bernoulli's equation relating Region 1 to Region 3 says:
Since A j = A3t the continuity equation implies \\ = V3. This means that the above relationship reduces to: Pi +Pg>'i = P3 + P8Y3
To make P\ equal to P3, yi must be equal to y3 (given that Aj = A3). For this to occur, y\ must increase, or y3 must decrease. This makes Options I and III valid. The lengthening of Region 2 will have no effect on the pressures against the
walls in Region 1 or Region 3. The best answer is choice D.
92
MINI-TEST EXPLANATIONS
I.
(1-5)
II.
III.
(34 - 37)
(38 - 42) (43 - 48) (49 - 52)
VII.
Buoyancy Balance
17-23
1-16
Passage I (Questions 1 - 5)
When a stress (which is pressure) is applied to a solid, it will deform slightly. The resulting deformation is called a strain. There are several ways of stressing a solid. In general,
stresses and strains are related through an elastic modulus E,
2.
A 1-m3 block of aluminum sank to the bottom of a lake of depth 750 m. By how much did the block shrink?
A. 0.1m3
B. 0.01m3 C. 0.001m3
D. 0.0001m3
as long as we remain within the elastic limitof the solid. The general relationship of stress to strain is:
E =
stress
strain
The stress is always an applied force per area, and the strain is always a fractional change in some dimension, such
as length or volume.
B =
3.
B.
Y>B>S
where V is the original volume of the solid, and B is a constant called the bulkmodulus that depends on the material
making up the solid.
C. Y = B,S<Y
D. Y = B,Y<S
As a second example of stress and strain, consider a cylindrical wire of length L and cross-sectional area A, attached to a ceiling with one end dangling. If a force F pulls the wire downward, perpendicular to A, it will stretch the wire by an amount AL. The amount of stretch is related to the amount of applied force through:
Y =
4.
How much work is done by a force F that stretches a wire of length L by AL, if the wire has cross-sectional area A, and Young's modulus Y?
A.
B. YAL L
YAL
F/A
al/l'
where Y is called Young's modulus and is a constant that
C.
L(AL)2
YA
D.
YA(AL)2
2L
2(1 + o)
3(1 - 2a)
5. Useful information:
YAAL
YAL
C. A.
B.
YA
P = 2B
P-=B
L
D. YA
C. P = B
4
D. P = B
2
94
8.
When an object is placed into a fluid, it displaces a set amount of that fluid. The displaced fluid exerts an upward force on the object This force is called the buoyant force and is equal to the weight of the fluid displaced. Qualitatively, the buoyant force is determined using Equation
1.
To lift a 2000 kg load with a hot-air balloon rather than a helium-filled balloon, what changes to the balloon
system should be made?
B = PfluidVfiuidg
Equation 1
where the mass of the fluid displaced has been written in terms of its density and volume. For an object that floats, the buoyant force is equal to the weight of the object. The buoyant force is determined from the submerged portion of the object, where V in Equation 1 is the volume of the object that is submerged.
Applications of the buoyant force usually involve objects floating in a liquid. However, air is a fluid, and objects can float in air as well. Buoyancy is the principle governing both
hot-air balloons and helium-filled balloons. The balloons
9.
displace an amount of the surrounding air, and this air exerts a buoyant force on the balloon. If the buoyant force is greater than the weight of the balloon, then the balloon will rise. The balloon continues to be accelerated upward until the buoyant force exactly equals the weight of the balloon. Helium-filled dirigibles (blimps) are used for slow air travel and can often be seen at major sporting events. Lateral motion in a dirigible is carried out using thrusters. A hot-air balloon can move laterally from either thrust or the presence of wind. The pilot of a hot-air balloon must depend on air currents for lateral displacement.
A.
increases.
B.
decreases.
6.
a heavy load, which of the following statements should be true? [Note: Tjn = temperature inside the balloon;
Tout = temperature outside the balloon.]
A. Tin = ToutJ me weight equals the buoyant force B. Tjn > Tout;the buoyantforce exceeds the weight C. Tjn < Tout; the weight exceeds the buoyant force
D. Tjn > Tout; the density of the air inside the balloon exceeds the density of the air outside the balloon.
5000
/m
(2000)(9.8)
7.
/m3
B.
position.
C. The center of mass for the hot-air balloon system shifts to a higher point.
D. The surface area of the balloon decreases.
vertical position.
95
Passage III (Questions 12-17) One method for gauging blood pressure in a vein or artery is to use a manometer. Its U-shaped tube is always open toatmospheric pressure on one end and connected to a small glass tube, the cannula, on the other. When this
cannula is inserted directly into the side of a vein, the local blood pressure competes with the atmospheric pressure to push a liquid solution, located in the tube, one direction or
the other. The solution level is located at the dashed line,
A. Halving only the atmospheric pressure. B. Doubling only the solution density. C. Doubling only the vein's blood pressure.
Equation 1
C. equal to that in both the arteries and veins. D. smaller than that in the arteries, but larger than that
in the veins.
A. Blood and saline are of similar density, thus allowing an accurate pressure calculation. B. To prevent blood from mixing with mercury, because the mixing blood will give erroneous
Figure 1
measurements of H.
Saline, used in the cannula, is chosen for two reasons: it is non-toxic and its density is small enough to measure the
C. To prevent blood from mixing with mercury, because of mercury's toxicity. D. To reduce the overall density of the manometer fluid, for increased precision in measuring H.
16. Compared to a healthy neighboring section of artery, a narrowed section (as a result of arteriosclerosis) yields: A. an increased height for the manometer reading and a larger blood flow velocity through the
constriction.
Pressure readings aid in diagnosing arteriosclerosis, a condition where plaque builds up on an artery's inner wall and restricts blood flow. Such changes in the flow speed correspond to changes in the local blood pressure. (Unless
otherwise stated, treat blood as an ideal fluid.)
12.
When the cannula is inserted into a healthy artery, which of the following saline levels could be seen in the manometer? (the arrow indicates the fluid level)
I. II. III.
B. a decreased height for the manometer reading and a larger blood flow velocity through the constriction. C. an increased height for the manometer reading and a reduced blood flow velocity through the
constriction.
D. a decreased height for the manometer reading and a reduced blood flow velocity through the
constriction.
.1
=L>
A. I and II only. B. II and III only.
17. A relatively high systolic blood pressure can cause arteries to expand. This expansion results from the relatively large:
A. bulk modulus of the blood.
96
21. In which of the following columns will the water level be the lowest when the valve is open and water is flowing out from point A?
I
18.
When a force F is applied to an copper wire of length L and cross-sectional area A, it stretches by AL. If the same force is applied to an copper wire of length L and cross-sectional area 2A, it stretches by:
II
III
IV
A. AL
4
B. 4L
2
C.
D.
2AL
4AL
Valve
19.
where blood flow periodically stops and starts again within an afflicted artery. This flutter is caused:
A.
Column I
Column II
A. by plaque buildup completely clogging the artery. B. by a variation in the local pressure, being occasionally less than or greater than the pressure
in the surrounding tissue.
B. C.
D.
Column III
Column IV
D. by a decrease in the blood pressure arising from a shrinking of the artery's diameter.
20.
Solution Z
HoO
A.
(b)PH2
water; its density
97
Av = k
24. How can the pressure exerted by the fluid BEST be described, as it passes from Region 1 through the tube
and ultimately through Region 3?
Equation 2
p + L pv2 + pgy = k
where P is the pressure, p is the fluid density, v is the velocity of the fluid, y is the height above some reference
level, and k is a constant
A. From Region 1 to 2, pressure increases; from Region 2 to 3, the pressure change is uncertain. P3 >Pl.
B. From Region 1 to 2, pressure decreases; from Region 2 to 3, pressure increases. P3 > Pi-
Figure 1 shows a tube designed for the study of fluid dynamics. An ideal fluid is forced through the tube from the left to the right, by way of an applied pressure. This tube can be treated as analogous to an artery in your chest.
Region 1
.A
C. From Region 1 to 2, pressure increases; from Region 2 to 3, the pressure change is uncertain. Pi
>P3.
D. From Region 1 to 2, pressure decreases; from Region 2 to 3, pressure increases. Pi > P3.
Region 2
Region 3
A. Increase A2 B. Decrease A2
C. Increase y2
D. Decrease yi
Figure 1. Tube for Studying Flow Dynamics
Fluid flows from left to right in Figure 1. Region 1 has pressure Pj, velocity vj, height y\, and area Ai; and similarly for Region 2, P2, V2, y2, and A2; and for Region 3, P3, V3, y3, and A3. The relative areas and heights are:
Ai=A3 = 2A2
and
y{ = y2
_ ya
22. How do the pressure and velocity of the fluid leaving Region 1 compare to the pressure and velocity of the fluid entering Region 2?
A. Velocity decreases by a factor of 2; pressure
doubles.
27.
B. P3 increases.
C. V2 increases.
D. V3 increases.
98
A. the tank must be at a greater height than the bowl. B. the Erkel tube must have an air space. C. the water in the bowl must be at the same height as
the water in the Erkel tube.
flap is opened. The flowing water serves to both increase the hydrostatic pressure in the bowl, and reduce the air pressure in the Erkel tube via an aspirator tube, causing the Erkel tube to act as a siphon tube. Figure 1 shows the basic schematic
of a toilet.
31.
Aspiral oi
Tube
What is the role of the aspirator tube in the toilet? A. B. C. D. To To To To reduce the air pressure in the Erkel tube. increase the air pressure in the Erkel tube. reduce the air pressure in the bowl. increase the air pressure in the bowl.
Erkel tube
32.
A siphon functions by having the two ends of a tube at different local pressures (typically because they are at different heights.) This is done so that fluid may flow from higher pressure to lower pressure. The flow is driven by a pressure difference between the two ends of the tube.
28. What is true of a functioning siphon during operation? I. The intake end of the siphon tube must be at a lower height than the output end of the siphon tube. II. Water flows because hydrostatic pressure is greater at the output end of the tube than the input end. III. The fluid in the tube must completely fill the tube, and flow must be initiated by a pressure difference.
A. II only
B. Both I and III
A. Pbase = Patm. B.
C.
D. Pbase = Pwatergntank
33.
A. the potential energy of the water in the Erkel tube. B. the potential energy of the water in the tank. C. the mechanical energy of the pump in the Erkel
tube.
C.
D.
29.
A. B. C. D.
high viscosity and low volatility. low viscosity and low volatility. high viscosity and high volatility. low viscosity and high volatility.
99
37. When a ship goes from the ocean into a lake, it will:
34.
Which of the following graphs BEST represents Ivolume stressl versus Ivolume strainl for an isotropic
solid within its elastic limit? A. B.
IVolume Strainl
IVolume Strainl
IVolume Strainl
IVolume Strainl
35.
A. the amount of hydrogen required to lift a balloon is prohibitive. B. hydrogen is less dense than air or helium. C. hydrogen is more dense than air or helium. D. hydrogen is highly reactive with oxygen gas.
36. What is the apparent weight of an object in water if it has a density of 10.0 g/mL and a weight of 60 N in air?
A.
B.
6N
30 N
C. D.
54 N 600N
100
39.
B.
C.
D.
16
32
APjtr4 8r)L
Raising r to the fourth power may seem unnerving at first glance, but the radius impacts both the cross-sectional area of the pipe as well as the average speed of the particles that make up the fluid. Two separate experiments are carried out to study blood flow. In both experiments, the viscosity of blood is taken to
A. 1.22 x 10"2 m3/s B. 7.93 x 10"3 m3/s C. 2.50 x 10"3 m3/s D. 9.16xlO"4 m3/s
Blood flows through pipes that are all 1.0 m long but have varying radii. AP is held constant as Q is being measured. The results of four trials are summarized in the following
table: Trial
1
Radius (mm)
10.0 20.0 30.0 40.0
AP(N/m2)
10 10 10 10
Q (m3/s)
1.96 xlO"5 3.14X10"4
3
4
Experiment B
Blood flows through pipes of constant radius 10 mm, but the lengths of the pipes vary. Q is held constant as AP is being
measured. The results of three trials are summarized in the
B.
following table:
Trial
1 2
Length (m)
1.0
2.0
Q (m3/s)
1.0 xlO'3
1.0 xlO"3
AP(N/m2)
510
1020 1530 C.
Length (L)
Length (L)
3.0
1.0 xlO"3
38.
If an additional trial of Experiment B were conducted with a pipe of length 2.5 m, the expected pressure
differential would be:
A. 765 N/m2
Length (L)
Length (L)
101
44. What counterweight is needed to balance the 50.0-g hanging mass in a liquid with a density of 1.20 g/mL?
A. 22.5 g B. 25.2 g C. 28.9 g
D. 29.6 g
46.
What would be observed for the experiment in an environment with reduced gravity?
A. More mass in the pan would be required to establish equilibrium. B. Less mass in the pan would be required to establish equilibrium. C. The exact same mass in the pan would be required to establish equilibrium. D. The amount of mass needed in the pan would be inversely proportional to the apparent weight of the hanging mass.
Figure 1 Pan Balance for Measuring Buoyant Force One-by-one, the students measured the counterweight needed to balance the hanging mass in four different liquids.
Table 1 summarizes the results for each trial.
47.
Which graph relates the apparent weight of an object to the density of the medium in which it is submerged?
A. B.
Table 1 Counterweight required to balance 50.0-g mass in each liquid and the density of each liquid
Fluid Medium
Air Water
Density (g/mL)
Density (g/mL)
C _
J3
*> -
Oil
Diethyl ether
Carbon Tetrachloride
37.1 g
24.7 g
I
c
1.49 g/mL
a, a.
Density (g/mL)
Density (g/mL)
I. More mass is needed to balance out the system. II. The object experiences a greater buoyant force. III. The object's apparent weight is reduced.
A. B. C. D. II only Ill only I and II only II and III only
48.
A. B. C. D.
float higher, because gravity is reduced. float lower, because gravity is reduced. remain the same, unaffected by changes in gravity. float higher, because gravity is increased.
102
49.
If one makes an analogy between fluid flow and electricity, pressure difference AP corresponds to:
A. current
B. voltage.
C. resistance.
D. capacitance.
50.
Releasing adrenaline dilates blood vessels, making it easier for blood to flow. By about what percentage
would the diameter of a blood vessel need to increase to
0%
4.7%
C. D.
10% 20%
51.
An object weighing 144 N is suspended by a string while completely immersed in water. The object has a density four times the density of water. What is its apparent weight?
A.
B.
108 N
72 N
C.
D.
36 N
576N
52. A floating object is 90% submerged in water and 60% submerged in CCI4. What is the specific gravity of CCI4 and the specific gravity of the object?
A. Object = 0.60; CCI4 = 0.67
1.
2.
D B
3. C 9. A 15. C
21. D
4.
5. C 11. D
17. A
6. 12.
7. A
13. D
19. B
8.
14.
10.
16.
22.
B
B
C
B D D
C D
18.
24.
23.
A C
B
D B
27. C
33. B
C
D A
29. B 35. D
41. C 47. B
30.
36. 42.
48.
C
A C
39. C
45.
46. 52.
C
C
51. A
103
Choice D is the best answer. How much pressure P must be applied to an isotropic solid, of bulk modulus B, to compress it to half of its original volume, assuming that the solid remains within its elastic limit at all times? If we compress it to half of
_ . _ . its original volume, then Vf = V This means that the change in volume AV is equal to AV = Vf - V; = V If we plug this 2 2
AV/V
=-
- (V/2)/V
In order to squash the solid to half of its original volume, we must apply a pressure equal to half of its bulk modulus. Notice that all three elastic moduli must be expressed in units of force/area. The best answer is D.
Choice D is the best answer. A 1-m3 block of aluminum sank to the bottom of a lake of depth 750 m. Finding out how
much the block shrank as a result of sinking requires determining the change in its volume AV. To find the change in volume, we need to know the applied pressure. Below the surface of a liquid at depth h, the pressure of any object increases due to the weight of the fluid column above it. So the pressure applied to the block is P = (pwater)Sn- Applying the bulk
modulus formula:
B = -
- __PSh
AV;
AV
V
/V
Rearrange terms to solve for AV: ^6 mf) AV =- (PlSV = - (1000)(10)(750)(lm') = _7.5 x 10" m3< , AV =_, x 1Q-4m3 . . aQ001 m3
7.5 x 1010
7.5 x 1010
The minus sign means that the change in volume is a decrease. This question is testing whether we can work with factors of
10 quickly. The best answer is choice D.
Choice C is the best answer. Suppose Y, B, and S are the Young's, bulk, and shear moduli of aluminum. Which statement is
true, ifa =J- for aluminum? Using the relations between Y, B, and S given in the passage:
B = Y
Y
3(1 -2a)
3 11 - 3/
si
13
With a little manipulation, B = Y, eliminating answer choices A and B. S and Y are related as follows:
S =
Y Y i + -
2(1+a)
4.
Choice D is the best answer. How much work is done by a force F that stretches a wire of length L by AL, if the wire has a cross-sectional areaof A, and Young's modulus Y?Since the answer choices look pretty nasty, we should use our knowledge
of units for this question (joules) to eliminate incorrect answer choices.
The units ofYare N/m2, the units ofLand AL are m, and the units ofAare m2. Examining the units ofeach choice leads to
the best answer. The answer in choice A is (Y)(AL)/L, with units of Nm/m2m = N/m2, which are the wrong units. The answer in choice B is YAL with units of (N/m2)m = N/m, which are the wrong units. The answer in choice C is L(AL)2/(Y)(A) with units of (mm2)/(N/m2)(m2) = m3/N, which are the wrong units. The answer in choice D is (Y)(A)(AL)2/2L, with units of(N/m2)(m4/m) = N-m =joules, which are the correct units.
You could solve this question using the relationship of W = Fyd, where W is work. The force can be found by manipulating Young's modulus, Y = //\AL' t0 've ^ = ']_ The distance that the center of mass travels during the stretch is
actually AL/2, not AL. This means that the work done is (YAAL/l)(AL/2) =YAAL /2l- The best answer is choice D.
Copyright by The Berkeley Review<s>
104
5.
Choice C is the best answer. Suppose an analogy were made between Hooke's law, F = kAx, and Young's modulus, (Stress) = (Y) (Strain). Which quantity in the Young's modulus equation corresponds to the spring constant k in Hooke's law? If we can rewrite the Young's modulus equation so that it looks like F = (constant)AL, then whatever constant we get corresponds to k.
Y = stress _ F/A
strain AL/L
=>
JF _ y A-L.
A L
=>
AL
The quantity Y-A- corresponds to the spring constant k. The best answer is choice C.
Passage II
(Questions 6 - 11)
Choice B is the best answer. The buoyant force is equal to the weightof the air that is displaced. It has nothing to do with
the weight (load), so thecalculation should notinclude 2000. This eliminates choices C and D. Theair density is solved for
as follows:
B _
B = Pairvair*g Pair =
V*ir'S (5000m3)(9.8k8/s2)
= 4.9 x 10
3 kg
/m-
Note that the volume of the air displaced is equal to the volume of the balloon. The numerator should only contain the
buoyant force, so choice A is eliminated and choice B is the best answer. If they ask for an exact value, it is sometimes
easier to use the order of magnitude rather than solve foranexact number. The best answeris choice B.
Choice A is the best answer. As the balloon rises, the external air pressure decreases. This is due to less air being present, therefore choice A is the best answer. Because the external pressure decreases, the balloon will expand, so its surface area increases. This eliminates choice D. The mass of the hot-air balloon will not change or shift relative to the balloon,
therefore choices B and C are eliminated. The best answer is choice A.
8.
Choice B is the best answer. The dirigible floats because helium is less dense than air. The hot-air balloon floats because hot air is less dense than cooler surrounding air. The difference in density between helium and air is far greater than the
difference in density between hot air and cold air. This is to say that atthe same temperature, air is denser than helium. This means that to achieve neutral buoyancy, a greater volume of hot air is needed than the volume of helium for the same load.
This makes choice B the best answer. Choice A is eliminated, because less mass (ballast) should be used with the hot-air
balloon given that it is less buoyant than a helium balloon of equal volume. Choice C is eliminated, because the hot-air balloon should have a greater volume than the helium balloon. Choice D is eliminated, because although equal moles of gases occupy the same volume, they do not have the same masses, so the weights are different. This results in different
buoyancy. The best answer is choice B.
9.
Choice A is the bestanswer. Momentum isconserved in the absence of a net external force. The balloon-package system is
initially moving vertically upward at constant speed, so this system is experiencing no net external force. Under these
conditions, the force of gravity is equal to the buoyant force, neglecting any resistance. Throwing a package out of the balloon will slightly decrease the gravitational force on the balloon, because the balloon now has less mass. Itwill therefore
accelerate upward, increasing its speed and thus increasing its momentum too. The solution is also found by noting that the system is initially in equilibrium. When the package is released ithas momentum downward, so the balloon must have an
increase in momentum upward to balance out the package's downward momentum. The best answer ischoice A.
10.
Choice B isthebest answer. For an object to float in a fluid medium, the density of the object must be less than the density
of the surrounding fluid medium. By heating the air inside the balloon, we decrease its density. The result is that the density
balloon must be greater than the temperature outside (which the name hot-air balloon implies). This eliminates choices A and C. The densities are not equal, so choice Dis also eliminated. Lift results, because the buoyant force is greater than the
weight of the system. The best answer is choice B.
of the air inside the balloon is less than the density of the air outside the balloon. This means that the temperature inside the
11.
Choice Dis correct. The passage references that lateral wind (crosswind) and thrust (due to the correct orientation of the burner chute) will cause lateral motion. This eliminates choices Aand B. A difference in local air pressures results in air flow (wind), because fluids flow from regions of higher pressure to regions of lower pressure. This can cause all sorts of motion, including lateral motion ifthe wind is a crosswind. The hot-air balloon will flow with the air currents. The hot-air balloon will not move laterally if the burner chute is positioned in a vertical manner, because the thrust force is vertical and
there is no lateral force. The best answer is choice D.
REVIEW EXAM EXPLANATIONS
105
Cannula
Choice C is the best answer. Since the average gauge pressure in the artery is greater than zero, the average pressure in the artery is larger than the atmospheric pressure. Consequently, the blood pressure should push the cannula fluid out (as in Figure III). You can think of what happens when you get cut. Blood squirts, oozes, or leaks out (you choose the more vivid word) from you, so it must be at a higher pressure than the atmosphere. Choice C is best, because the height difference results from the pressure in the cannula being greater than the atmospheric pressure. In Figure I, the blood pressure is less than atmospheric pressure and in Figure II, the blood pressure is equal to atmospheric pressure. Neither of these are valid
scenarios, so choices A, B, and D are all invalid. The best answer is choice C.
13.
Choice D is the best answer. Equation 1, given in the passage, has three terms in it: Pbbod, Patm, PsoiutiongH- Doubling H
doubles the last term in the equation. One way to double H is to double the other two terms. Since the first three choices refer to doubling or halving single variables, but no choice refers to doubling both terms, vve can eliminate choices A, B, and
C. If the blood pressure is increased such that the difference between the blood pressure and the atmospheric pressure (Pbiood - Palm) doubles, then the height, H, would double. That in essence is what choice D is saying. The best answer is choice D.
14.
Choice C is the best answer. Because no blood is lost as it goes through the arteries, through the capillaries, and through the veins, the blood mass flow rate must be the same through each region. Since blood is a fairly incompressible fluid and the arteries and veins undergo minimal expansion, the average blood volume flow rate must also be the same through each
region. The best answer is choice C.
15.
Choice C is the best answer. As stated in the passage, the saline is non-toxic. Nothing is stated in the passage about mercury being toxic, but it can be inferred from the fact you need a non-toxic buffer between blood and mercury. Since Hg
is toxic, the saline buffer keeps the Hg out of the patient's blood stream. Choice A starts off with a true statement that saline
and blood have relatively similar densities, but that is not necessary to measure blood pressure. Choice A is eliminated.
Choice Dis also tempting, because using a less dense solution would result in a bigger H. This would be easier to precisely
measure, but choice C is the better answer, because if precision of that sort was necessary, then mercury would not be used at
all. The best answer is choice C.
16.
Choice B is the best answer. Using the continuity equation, Aiv7 =A2V2, a decreased flow area in the artery leads to an increased flow velocity ofthe blood. This rules out choices Cand D. Using Bernoulli's equation, an increased flow velocity leads to a decreased local pressure against the walls in the narrowed region. Using Equation 1from the passage, a decreased
blood pressure leads to a decreased height for the manometer reading. The best answer is choice B.
17.
Choice A is the best answer. If the artery expands, either the blood is relatively incompressible or the artery is relatively
pliable. Since blood is a fluid, it has no Young's modulus by definition (Young's modulus refers to a solid). This rules out choice B. Choices C and D would correspond to stiffer arteries, which would be less likely to stretch, so they are both eliminated. Ifthe bulk modulus ofblood is large, then it is relatively incompressible, meaning that the high systolic pressure
causes thearteries to expand rather than the blood to compress. The best answer is choice A.
Questions 18 - 21
18.
Choice B is the best answer. When a force F is applied to a copper wire of length L and cross-sectional area A, itstretches by AL. Ifthe same force is applied to a copper wire oflength Land cross-sectional area 2A, itstretches by how much? First,
let's use a little common sense to eliminate incorrect answer choices. The second copper wire is thicker than the original
copper wire. This tells us that for the same force, the second wire should notstretch as much as thefirst wire. So our answer
has to be less than AL. This eliminates choices Cand D. The best way to choose between the remaining choices Aand Bis to
set up a ratio, using the Young's modulus equation:
AL new
FL
YA new
AL =
FL YA
AL new = AL
(-AJ = AL(_A_) = AL
\Ancw) \2Al 2
The best answer is choice B. Try to answer the same question, this time assuming that the diameter of the second wire is
twice that of the first wire. That is a common twist on this kind of problem. The best answer is choice B.
106
19.
Choice B is the best answer. The phrase "periodically starts and stops", within the question, suggests that the cause of the flutter must be a periodic or varying phenomenon. Only choice B refers to a scenario where fluctuation occurs. Plaque build up would permanently clog it up, so it would not cause a fluctuation. This eliminates choice A. Choices C and D arc true statements that are irrelevant to the question. Neither account for a stopping and starting phenomenon. Choice B describes a
scenario where the pressure fluctuates between greater than and then less than, which would correlate to the blood flowing and then not flowing. Choice B is the best answer. The best answer is choice B.
20.
Choice D is the best answer. Because Solution Z is floating on water, it must be less dense than water. This eliminates
choice A. According to Archimedes Principle, the mass of water displaced is equal to the mass of the Solution Z. The
volume of water displaced is 7tr2b while the volume of Solution Z is 7rr2(a + b). This means that a column of water with
height b has the same mass as a column of Solution Z with height a + b. The value of a is less than b (as the picture shows), so the density of Solution Z is slightly less than the density of water. We know from the picture that the density of Solution Z is more than half of the density of water, because b is greater than a. This means that the density of Solution Z is found by multiplying the density of water by a number greater than 0.50, but less than 1.00. This is true only in choice D. Choices B and C are the result of multiplying the density of water by a number less than 0.50. The mathematics of equating the pressures is shown below:
(a + b)
21.
Choice D is the best answer. This question combines the continuity equation with Bernoulli's principle. First off, when the valve is opened, water will flow from the reservoir, through the open valve, and then through the outflow pipe and out through point A. As the water flows through the side pipe, some water will climb the various columns, according to the
pressure it exerts against the walls at the point where it passes the column. The greater the pressure exerted by the moving
water against the walls, the higher that pressure will push water up the column. Because the outflow pipe is narrowing from the point where it intersects Column I to the point where it intersects Column IV, the average speed of the water is increasing as it flows to the right. According to Bernoulli's principle, as the flow speed of a fluid increases, the pressure it exerts against the walls decreases. This means that the moving water will exert the highest
pressure against the walls as it passes the base of Column I and the least pressure against the walls as it passes the base of
Column IV. A lower pressure manifests itself as a smaller height for the water in Column IV. Even if you were unsure of the
physics involved with this question, hopefully you saw it as an extreme question and you eliminated choices B and C,
columns in the middle. The best answer is choice D.
Choice C is the best answer. Because the area is being cut in half as the fluid flows from Region 1 into Region 2, the
velocity of the fluid must be increasing, ultimately by a factor of 2 (the relative sizes of the two regions). This eliminates choices A and D. When the velocity increases, the 1/2 pv2 term in Equation 2 must increase: so, for the overall equation to stay constant, the pressure against the walls of the pipe must be reduced. The exact amount by which the pressure is
decreased is uncertain, because the values of P and vj are not given. The best answer is choice C.
23. Choice B is the best answer. Using the continuity equation, we find that:
Aivi = A2V2 = A3V3
Because A\ = 2A2 (as given in the passage), V2 is double v\. Because A1 = A3 (as given in the passage), v\ must be equal
to V3. This means that V2 is the greatest. The best answer is choice B.
24.
Choice D is the best answer. As the fluid flows from Region 1 to Region 2, the cross-sectional area decreases, so the
velocity must increase, according to the continuity equation (Equation 1). Because the V2 pv2 term in Bernoulli's equation
(Equation 2) increases while the pgy term is constant, the pressure must decrease. This eliminates choices A and C. Choices
B and D differ in their comparison only of the pressures in Regions 1 and 3. Because their cross-sectional areas are the same, both regions have the same flow velocity. Because Region 3 is higher than Region 1, Region 3 must have a lower pressure than Region 1 if Bernoulli's equation is to remain balanced. The best answer is choiceD.
107
25.
Choice A is the best answer. Using the continuity equation, if A2 increases, then V2 must decrease. If V2 decreases while y2 remains unchanged, Bernoulli's equation states that the pressure must increase. Increasing y2 (the height of Region 2) will reduce the pressure in that region, so choice C should be eliminated. Changing yi should have no direct effect on the pressure in Region 2. The best answer is choice A.
Choice A is the best answer. We can see from Equation 2 that the two factors affecting the pressure that vary between the regions are the height (y) and the velocity (v). The following relationship holds true:
26.
The continuity equation relates the cross-sectional area of the pipe to the average particle speed, where Av = k as long as the volume flow rate remains constant. Because A1 = 2A2 = A3, V2 = 2v\ - 2V3. This means that V2 is the greatest velocity. As given in the passage, y3 > yi = y2- In order for the equality to hold true, P\ must be greater than both P2 and P3. The greatest pressure is found in Region 1, where the area is greatest and the tube is lowest. The best answer is choice A. 27. Choice C is the best answer. According to the continuity equation: A2V2 = k. Therefore, A2jV2i = A2f\'2f- If A2 decreases, V2 must increase to satisfy the continuity equation. This makes choice C the best answer. According to Bernoulli's equation,
Pagainst walls + '/pv2 + pgh = k, P2 should decrease if V2 increases. This rules out choice A. Velocity and pressure in
Regions 3 will have no bearing on the pressure or velocity in Region 2. This makes choices B and D invalid. The best
answer is choice C.
Choice C is the best answer. A siphon works because the two ends of the siphon tube are at different heights, and thus different potential energies. In order to have water flow from the intake end to the output end, there must be a net pressure difference, where the gauge pressure is greater at the output end. This occurs when the outputend is at a lower height, thus it
is at a point of greater hydrostatic pressure. This makes Statement I invalid. This same reasoning makes Statement II valid. In order to get siphoning started, there must be an initial difference in pressures that is great enough to get the water to flow. The tube must also be full, otherwise the air pocket cannot be displaced, and the fluid in the tube cannot flow. This makes
Statement III valid, and thus makes choice C the best answer. The best answer is choice C.
29.
Choice B is the best answer. Fora toilet to function, the liquid (fluid) must beable to flow. If the viscosity is high, then the ability to flow is reduced. The greater the viscosity, the greater the pressure difference that is required to get the fluid to
flow. Ideally, the fluid should have low viscosity. This eliminates choices Aand C. Low volatility is ideal sothat the liquid
in the tank and bowl does not evaporate away. If the liquid evaporates away from the bowl, then the fluid height in the Erkel tube will drop, and the siphon cannot be established. Ideally, the volatility of the fluid should be low. The best answer is
choice B.
30.
Choice D is the best answer. Because water must flow from the tank into the bowl, the height of the water tank must be greater than the height of the bowl. Choice A is a valid requirement. The Erkel tube must have an air space at the top of the
tube so that air pressure can be reduced, and thus a pressure difference can be established between the two ends of the Erkel
tube. Choice B is a valid requirement. A fundamental idea in physics is that a liquid will seek the lowest point. Because water in the bowl is free to fill the base of the Erkel tube, the height of water in the bowl at rest is equal to the height of the water in the Erkel tube at rest. Choice C is a valid requirement. In order for the aspirator to reduce the air pressure in the Erkel tube, it cannot have any water present. As water flows from the tank into the bowl, air pressure in the tank is reduced, so air pressure in the aspirator tube is also reduced. This generates the reduced pressure that helps water (and various solutes and possible insoluble solids-nice way to put it) to flow through the Erkel tube (siphon). Choice D is NOT a valid
requirement, and picking it might just make you score like the mighty Toledo Mudhens. The best answer is choice D.
31.
Choice A is the best answer. The role of aspiration in general is to take advantage of fluid flow to reduce the pressure in a
column. As a fluid flows across the top of an open-end column, the pressure inside of the column will be reduced. In the case of a toilet, if the pressure in the aspirator tube is reduced, then it will lower the gas pressure of the air behind the Erkel
tube. This makes choice A the best answer. Choices C and D can be eliminated, because the change in air pressure in the bowl is negligible. It can also be thought of in terms of PV = nRT. As water leaves the tank, the volume of the air space above the water increases, resulting in a drop in pressure. The aspirator tube is open to the air space, so it experiences a drop in pressure as well. The air space in the Erkel tube has a drop in pressure while the bowl has a gain in pressure due to the
additional water. This causes the pressure difference between the two ends of the Erkel tube. The best answer is choice A.
108
32.
Choice C is the best answer. At the base of the water tank, there is a column of water and the atmospheric air above. This means the pressure at the base of the water tank is due to the pressure from the column of water (pgh) and the atmospheric pressure. The best answer is choice C. Choice B is the best answer. Choices C and D can be eliminated immediately, because there is no pump associated with the toilet shown in Figure 1. This means that there is no mechanical energy associated with a toilet. Because the water tank it at the highest point, the water in the tank has the greatest potential energy of anything in the toilet. This potential energy is used to force the water to flow through the toilet system. The best answer is choice B.
33.
Questions 34 - 37
34.
Choice D is the best answer. We are looking for the graph that best represents Ivolume stressi versus Ivolume strainl for an
isotropic solid within its elastic limit. Stress and strain are directly proportional to each other. For a solid, stress = E (strain), where E represents Young's modulus. As one value increases, so should other value. This eliminates choices A and C. The
elastic modulus that relates volume stress and volume strain is B. The general relation is Ivolume stressi = B Ivolume strainl, which confirms that they are directly proportional to one another. So the graph should be a straight line with a positive slope.
The best answer is choice D.
35.
Choice D is the best answer. Hydrogen was actually used as the gas to lift balloons well into the early twentieth century. However, hydrogen is so combustible that it is dangerous to use (as most of us have learned from the Hindenberg disaster.)
The reason hydrogen was used in the first place is because at 2 grams per mole (the molecular mass of H2 gas), hydrogen is
half as dense as helium which has an atomic mass of 4 grams per mole. This makes a hydrogen-filled balloon system less massive than a balloon filled with helium, and therefore easier to lift off from the ground. The best answer is choice D.
36.
Choice C is the best answer. The object is denser than water, so it will sink when added to water. Because of the buoyant
force, its apparent weight will be less than its actual weight. As such, the apparent weight is less than 60 N. This eliminates choice D. For an object that sinks in a fluid medium, the ratio of its density to the density of the fluid medium
(Pobjcct/pmedium) is equal to the ratio of the weight to the buoyant force (Fweight/Fbuoyant). In this case, the ratio of the
densities is 10 g/mL to 1 g/mL, which equals 10. This means that the buoyant force of the object is 6 N (60N/10). Given that the magnitude of the weight is equal to the sum of the magnitude of the apparent weight and the magnitude of the
buoyant force (Fweight = Fbuoyant + ^apparent weight), the apparent weight is the difference between the actual weight (60 N)
and the buoyant force (6 N). The apparent weight is 54 N.
Fbuoyant = 60Ji = 6N
10
Fweight - Fbuoyant + Fapparent weight ' Fapparcnt weight - Fweight" Fbuoyant -60N-6N-54N
Choice D is the best answer. The density of the ocean (saltwater) is greater than the density of a lake (fresh water). Because
the ship goes from a denser medium to a less dense medium, it will experience an increase in the submerged volume, which occurs to keep the buoyant force constant. You should recall that when the ship floats, the buoyant force equals the weight of
the ship, and that the buoyant force is found using: Fbuoyant = Pmedium'Vdisplaced'g- Fbuoyant and g remain constant, so as
Pmedium decreases, Vdispiaced must increase. The ship floats lower in a lake than the ocean, so choices A and C are
eliminated. Next, we must consider that the weight of the ship didn't change when the medium changed, so the buoyantforce needed to offset the weight of the boat when it floats should also remain the same. Choice B is eliminated. The best answer
is choice D.
Poiseuille's Law
Choice B is the best answer. To approximate how an additional trial of Experiment B with a pipe of length 2.5 m would
come out requires interpolation. One method to solve this problem would be to find a ratio between the new trial and one of the trials in the table. In this case, you can almost get the answer directly from the table. Since L for the new trial has a value
between L for Trial 2 and Trial 3, AP for the new trial should also be between AP for Trial 2 and Trial 3. This means the
correct answer must be choice Bor choice C. For each meter ofpipe, the pressure difference increases by 510 N/m2. As we go from L= 2.0 mto L= 2.5 m, the pressure should increase by 255 N/m2. So AP for the new trial should be 1020 +255 =
1275 N/m2. The best answer is choice B.
109
39.
Choice C is the best answer. If Q is held constant and r is decreased to half of its original value, AP must increase by what
factor?
Q =
APjtr4 8r|L
Substitute V2 for r: Q =
APjr(r/2) =\ 16 / =(l\APjrr4
8tiL 8rjL "" U6/ 8tiL
To keep Q constant, we must increase the pressure difference by a factor of 16! The best answer is choice C.
40.
Choice A is the best answer. If an additional trial were conducted in Experiment A with a pipe of radius of 50 mm, what would the expectedflow rate be? To do a problem like this, the best method is to find the ratio between the value of Q in the
new trial and the value of Q in one of the trials in the table. Let's find the ratio between the new trial and Trial 1:
APjt(r,
'new
r and Ql=^r1rj
8r|L
so
*rnew)
8r|L
Qi
(ri)4
= Qi
Choice C is the best answer. If water and blood were to flow through identical pipes with the same flow rate, which fluid would require the larger pressure difference? The viscosity of blood is larger than the viscosity of water, so vve can eliminate
choices Aand D. We can manipulate Poiseuille's equation to find out how pressure difference depends on viscosity and flow
rate:
AP oc Qr|
Since both fluids have the same flow rate, the one with the greater viscosity requires the greater pressure difference. Blood
has greater viscosity. The best answer is choice C.
42.
Choice A is the best answer. The graph that best represents how the flow rate ofa fluid varies as the length of the pipe is changed (if rj, P, and r remain constant) requires manipulating Poiseuille's equation to show that flow rate is inversely proportional to the pipe length (Q 1/L). Choice Ccan be eliminated, because itstates that the flow rate does not depend on pipe length. Choice Dcan be eliminated, because itstates that the flow rate is directly proportional to pipe length. The graph
in choiceA is the only graph that plots Q versusL in an inverse manner. The best answer is choice A.
Passage VII
43.
(Questions 43 - 48)
Buoyancy Balance
Choice D is the best answer. As the density of the fluid medium increases, the buoyant force is increased. This makes Statement II a valid statement, and eliminates choice B. Because the magnitude of the weight is equal to the sum of the
magnitude of the apparent weight and the magnitude of the buoyant force (Fweight =Fbuoyant +Fapparent weight), the apparent
weight is the difference between the actual weight and the buoyant force. As such, an increase in the buoyant force results in the apparent weight being reduced. This makes Statement III a valid statement, which eliminates choices Aand C. The only
choice remaining is choice D, so it must be the best answer. This implies that Statement I is invalid, which is true, because if the apparent weight is reduced, then less counterweight is necessary. The best answer is choice D.
44.
Choice Disthe best answer. This question can be solved by comparing the information in the question to the data in Table 1. A 33.1 g counterweight is necessary in a fluid with a density of 1.00 g/mL and a 24.7 g counterweight is necessary in a fluid with a density of 1.49 g/mL. With a fluid ofdensity 1.20 g/mL, the counterweight should be between 24.7 grams and 33.1 grams, being a bit closer to 33.1 grams than 24.7 grams. This eliminates choice A. The average of 24.7 and 33.1 is
28.9, so the counterweight should be a little heavier than 28.9 grams. This eliminates both choices B and C and leaves
choice D as the best answer. This question tested your ability to work with numbers in a table, which is something that is
common on the MCAT. The best answer is choice D.
110
45.
Choice C is the best answer. The hanging mass sinks in all of the fluid mediums, so it must be more dense than each of the
fluids. The densest liquid is carbon tetrachloride, with a density of 1.49 g/mL, so the hanging mass must have a density greater than 1.49 g/mL. This eliminates choice A. To solve for the exact density, we can compare the weight to the buoyant
force. For an object that sinks in a fluid medium, the ratio of the density of the object to the density of the fluid medium
(Pobject/pmedium) is equal to the ratio of the weight to the buoyant force (Fwejght/Fbuoyant)- Because the object is at rest, the
magnitudes of the forces up must equal the magnitude of the force down. In air, a counterweight of 50.0 grams is necessary, so the mass of the hanging object is 50.0 grams. Its weight is therefore 0.05g N. The counterweight needed in carbon tetrachloride is 24.7 grams, about half of its weight. Because the weight is balanced out by a buoyant force and tension in
the string holding the mass (which results from the counterweight), we can set the forces equal. This means that Fweight = Fbuoyant + Fusion- The tension is 0.0247g and the weight is 0.05g, so the buoyant force is 0.0253g. The relative densities
can be set equal to the weight-to-buoyant force ratio, which is 0.05g/0.0253g. That ratio is about 2 : 1, so the density of the object must be about double that of carbon tetrachloride. Carbon tetrachloride has a density of 1.49 g/mL, so the hanging mass must have a density near 3.00 g/mL.
PHanging mass
_ ^weight _
'weight
0.05g N
0.05g
_5_ = 2.5
PCarbon tetrachloride
2.0 =
Fbuoyant
PHanging mass
0.05g N - .0247g N
0.0253g
PCarbon tetrachloride
The best answer is choice C.
46.
1.49 g/mL
Choice C is the best answer. In reduced gravity, the weight of the object and the counterweights would be reduced as would
the buoyant force. All of the forces depend directly on g, so a reduction in gravity would impact all of the forces by an equal percentage. This means that all of the masses could remain the same, making choice C the best answer. Choice D can be eliminated, because the apparent weight is the equal to mass of the counterweight, so they are not inversely related. The best
answer is choice C.
47.
Choice B is the best answer. If an object has an apparentweight in a fluid medium, it must be more dense than the medium.
In such a case, the magnitude of the buoyant force and the magnitude of the apparent weight add up to equal the magnitude
of the object's weight. This means that as the magnitude of the buoyant force increases, the magnitude of the apparent weight decreases. The buoyant force is directly proportional to the density of the fluid medium (Fbuoyant =
Pmedium'vdisplaced*g) so the apparent weight must decrease as the density of the fluid medium increases. This eliminates
choices A and D. The relationship is not inversely proportional, so the graph is not asymptotic. This eliminates choice B.
The relationship is linear, because they add to a sum. As one increases, the other decreases by the same amount. The best
answer is choice B.
48.
Choice C is the best answer. An object floating in water, such as an ice cube, does so because its weight (mg) equals the
buoyant force (Fbuoyant = Pmedium-Vdispiaced'g)- When going to an environment with a change in the gravitational force
constant (g) such as the moon, the weight at buoyant force are impacted equally. If the object is floating in the first place, it
will continue to float in the exact same fashion when the gravitational force changes. Choice C is the only choice that fits this information. Choice D should be eliminated immediately, because gravity is reduced on the moon. Moon problems are quite
common in physics, so it's not a bad idea to contemplate what happens to various forces and systems when the value of g
changes. The best answer is choice C.
Questions 49 - 52
49.
Choice B is the best answer. If one makes an analogy between fluid flow and electricity, pressure difference, AP, will
correspond to the electrical driving force. The comparison we should make involves Ohm's law:
corresponds to choice B. In a more conceptual perspective, the pressure can drop as the blood flows, just as voltage may drop as current flows. Equally, opposing pressures result in no blood flow, just as opposing voltages result in no current. The best
answer is choice B.
In the analogy with electricity, AP corresponds to V, Q corresponds to I, and 8r)L/jrr4 corresponds to p(L/A). This
111
50.
Choice B is the best answer. The volume flow rate of an ideal fluid depends on four factors: the pipe's length, the pipe's
radius, the pressure difference between the two endsof the pipe, and the viscosity of the fluid. In this question, the length, fluid viscosity, and pressure difference remain constant, so we need only consider the change in the radius of the vessel. The
relationship isQ a r4, where Q represents the volume flow rate of blood and r represents the radius of the blood vessel. You
may have noticed that they mentioned diameter in the question to throw us off a bit, but any percent-change in the diameter has an identical percent-change in radius. If a blood vessel dilates, then there is a greater cross-sectional area and the volume
flow rate will increase. This eliminates choice A. Because r is raised to the fourth power, a 20% change in radius would lead
to a greaterincrease in volume flow rate than 20%, so choice D is eliminated. At this point, we are faced with some daunting math. Rather than taking the fourth root of 1.20 (the ratio of Qfinal to Qinitial). we are better suited to pick one of the answer
choices and raise it to the fourth power to see if we get 1.20. Let's try 10%, because it looks like the math will be easier than
4.6%. A 10% increase would results inan rf,nai to rjn}tial ratio of 1.10.1.104 isgreater than 1.20 (given that 1.102 = 1.21), so
choice C is not correct. Only choice B remains, so it must be correct The best answer is choice B.
51.
Choice A is the best answer. This question is best solved by first recognizing that the object is a sinker. Because it's a
sinker, we can start by noting that the ratio of the densities of the object and medium is equal to the weight-to-buoyant force ratio. The question tells us that the object's density is four times the density of the surrounding water, so the weight of the object must be four times the buoyant force. One-fourth of the weight is equal to 36 N, so we know that the object has a weight of 144 N and experiences a buoyant force of 36 N. The buoyant force is the apparent weight loss, so to determine the buoyant force, we need only subtract the apparent weight loss from the weight This would be 144 - 36 = 108 N, choice A.
Be careful on questions like this not to accidentally choose the buoyant force as the final answer, because it's highly likely thattest writerswill leave that as a potential choice. Just to be complete, let's draw a pictureof the system.
Notes:
B=jxl44N =36N
T = 144-36N=108N
\y
~" B
Q
W=144N
52.
Choice C is the best answer. First off, we can apply a convenient short cut for an object that floats. When an object floats,
the ratio ofthe densities of the object and medium isequal to the percent of the object that issubmerged. In this case, where the medium is water, the ratio ofthe densities is also known as the specific gravity. Because the object is 90%-submerged in water, it has a specific gravity of 0.90. This eliminates choice A. Because the object floats higher in CCI4 than it does in water, we can conclude that CCI4 must be denser than water, which means the specific gravity of CCI4 must be greater than 1. This eliminates choice B. To decide between the remaining two choices, we'll need to compare the percent submerged in water to the percent submerged inCCI4 inorder to determine the density of CCI4 relative tothe density ofwater. The ratio of the submerged percentages is90:60 = 3:2 = 1.5. This means that the specific gravity ofCCI4 is 1.5, eliminating choice Dand
making choice C the best answer. A more detailed solution is shown below.
Because the weight of theobject is equal to itsbuoyant force in water and its buoyant force in CCI4:
PCCl4VSubmergedg = PH20'vsubmergedg
112
Electrostatics and
Electromagnetism
Physics Chapter 8
by
the
Berkeley Review
Electrostatics and
Electromagnetism
Selected equations, facts, concepts, and shortcuts from this section
O Important Equations
Felectric = qE
F = qv x B = qvB sin8
W = qEAd = qAV
F = 1/ x B
= "y m
Important Concept Charged particles behave differently in an electric field than a magnetic field
F =
qE
F = qvB sin9
r_ mv
! '
''
y'
y'
y*
yi
y*
Like Le Chatelier's principle in chemistry, Lenz's law predicts that the system will react to undo achange
"X"
xxxx
xxxx
Loop enters 1B field oriented into page Change: Gains Xs inside ofloop
Loop exits 1B field oriented into page Change: Loses Xs inside ofloop
Reaction: Induce a counterclockwise current to create 0s. Reaction: Induce a clockwise current to create Xs.
Physics
Electrostatics
Atoms are the building blocks of matter. They consist of electrons, protons, and neutrons. Electrons carry a negative charge, protons carry a positive charge, and neutrons carry no charge at all; they are neutral. The masses of these three particles are shown in Table 8-1. Note that the mass of a proton is about 2000 times greater than the mass of an electron. Also note that the masses of a proton and a neutron are approximately equal to one another.
Particle
Electron
Proton
Mass (kg)
9.11 x 10"31 1.673 x lO"27 1.674 x lO"27
Table 8-1
Charge (C)
-1.6 x 10"19
+1.6 x 10"19
0
Neutron
Protons and neutrons comprise the nucleus of an atom, whereas electrons stay in orbits about the nucleus. An atom in its simplestform has an overall net charge of zero, because the number of protons equals the number of electrons. Atoms differ from each other by the numbers of electrons, protons, and neutrons they
contain.
If an atom were to lose an electron (most often it loses the electron from its valence shell-outermost orbital), then that atom would have an overall net
charge of +1 and is said to be a positively charged ion. Similarly, if an atom were to gain an electron in its valence shell, then thatatom would have an overall net charge of -1. This atom is said to be a negatively charged ion. When atoms gain or lose electrons, they undergo a process called ionization. You should note that in chemistry the ionization energy is the energy associated with losing an electron. If a negatively charged atom is close to a positively charged atom, there will be an attraction between those two opposite charges that strengthens as the
distance between them decreases. However, there will be repulsion between two
repulsive force also increases in magnitude as the charged species draw closer to
one another.
positively charged atoms or two negatively charged atoms. The strength of the
115
FhySlCS
Electrostatics
For example, when we rub a plasticrod with fur, the rod acquiresa net negative charge while the fur acquires a net positive charge. In the process of rubbing the
rod with the fur, electrons were transferred from the fur to the rod. The net
charges on these two objects are opposite in sign and alwaysequal in magnitude. Charge has been conserved. In charge conservation, the total electric charge on the plastic rod and the fur (or any other two objects) does not change. Even though charge can be transferred from one objectto the next, it cannot be created
or destroyed.
Conductors and Insulators A conductor is a material that allows for the movement of charge. An insulatoris a material that impedes the movement of charge. Many of the metals that we know of (e.g., copper or silver) are good conductors. These metals allow for the flow of electrons. Nonmetals (e.g., glass or plastic) are typically good insulators.
Electrons generally do not flow in these materials.
In the mid-1780s, Charles Coulomb discovered that the electrical force exerted by
two charges exerts onthe other can be expressed in terms ofequation (8.1). This equation is called Coulomb's law and as written applies only to charges in a vacuum. The proportionality constant k depends on thesystem ofunits used in
the calculation.
onecharged object on another charged object dependson the distance r between those two objects, the sign of the charges on each object, and the amount of charge q on each object. The magnitude of the electrical force F that each of the
F- iJqiq2l
r2
(8.1)
The SI unit of charge is called the coulomb (C). The magnitude of the charge of an electron ora proton (denoted by e) is 1.60 x 10"19 C. One coulomb equals the charge carried by an aggregate of 6.3 x1018 protons (or the negative of 6.3 x1018
electrons, based on theamount ofcharge that flows in 1 second when the current
is 1 amp). In the SI system of units we also find that the units of the constant k
In equation (8.1), the electrical force F is the magnitude of a vector quantity. It will always be a positive value. However, the product of the charges qi and q2 can be either positive (if the charges have the same sign) or negative (if the charges have opposite signs). The absolute value bars in equation (8.1) ensure
the force that each charge is exerting on the other is always along a straight line joining the two charges. Even though the forces are opposite in direction, they
are equal in magnitude (recallNewton's Third Law of motion).
they will attract one another (Figure 8-lb). Figure 8-1 shows thatthe direction of
As we have mentioned, iftwo objects have charges with the same sign, they will repel one another (Figure 8-la). If two objects have charges with opposite signs,
Figure 8-1
116
Physics
Electrostatics
The magnitude of this force, when plotted as a function of the charge separation, is often shown as the upper graph in Figure 8-2. If we consider the sign associated with force, then the graph could be either the upper graph or the lower graph in Figure 8-2. For the sake of this graph, we shall consider repulsion to generate a positive force (when the charges have the same sign) and attraction
to generate a negative force (when the charges have opposite signs). This "1/r2
dependence" of the force is similar to that for the gravitational attraction of two masses;it is a mathematical relationship that reappears in the discussion of many physical phenomena. Because of its ubiquity in physics, knowing how to plot the inverse-square law and understanding it conceptually is a good idea.
Repulsive
clO-
Separation r
Figure 8-2
When considering electrical charges, you shouldhave a feeling for the sizeof the charge itself. A charge equal to onecoulomb is a huge value. Using equation (8.1)
to calculate the forcebetween two 1-C charges exactly 1 meter apart, would yield
a magnitude of the force is about 109 newtons. We can put this into a more
familiar context: knowing that 1 N = 0.225 lbs and that 2000 lbs = 1 ton, we can calculate that the magnitude of the force between these two charges would have a gravitational force equivalent to roughly a million tons. In realistic calculations,
charges typically have values that fall within the range of 10"9 to 10"6 C.
Before a voltage is applied across a wire, the wire has no net charge. After applying a voltage, the net charge on the wireis:
A. B. C. D. negative, if the current flows from higher to lowervoltage. positive, if the currentflows from higherto lower voltage. zero, regardless of the current direction. a non-zero value that depends upon the current direction.
Example 8.1a
Solution
traditionally defined as flowing positive charges, moves from higher to lower voltage. However, for the purpose of answering the question, we need to know
that current makes electrons flow into the wire and out of the wire. On average,
the number of electrons leaving the wire equals the number entering. Thus, the net charge on a wire will not change-it will be neutral, with or without the
current. But with a current, it will have an induced dipole.
The best answer is choice C.
117
Physics
Electrostatics
When NaCl dissociatesin pure H2O, the net charge of the electrolyticsolution:
A. becomes negative. B. becomes positive.
C. remains neutral.
concentrations.
D. becomes positive or negative, depending upon the relative Na+ and Cl"
Solution
A crystalline salt comprised of +l-cations and -1-anions, such as NaCl, has equal
number of (+)-cations as (-)-anions. This means that when added to neutral
Example 8.2a
Solution
Let's approach it using the ratio method. The tworelevant equations are:
ana
and
F. - ^l^l Electrostatic ~
Because both equations share the same denominator, we can disregard distance. Taking the ratio of the electrostatic force to that ofthe gravitational force gives:
Fgravitational
Before embarking on an arithmetic adventure, notice that the choices offered as answers differ by several orders of magnitude from each other. Therefore, we could avoid worrying about how the prefactors, such as 9 and 1.6, affect the
answer. Just add and subtract the powers of 10. Doing so gives a ratio of about
1044 to 1, which is closest to choice A. (The actual answer is 3.97 x1042 to 1.)
Aside from a chance to practice arithmetic approximations, this problem reveals
a few facts about electrostatic and gravitational forces. First, the two force equations look similar-just an exchange of mass for charge and an altered
constant (being aware that gravitational forces are always attractive, whereas
out, meaning that this force ratio is the same whether the charges are 1 nm or 1 km apart. Finally, notice that the electrostatic force is much stronger than the
gravitational one. This explains why electrostatic force problems almost never mention gravitational forces when asking abouttheacceleration ofcharges.
The best answer is choice A.
electrostatic forces can alsobe repulsive). Second, their similar 1/r2 terms cancel
118
Physics
Example 8.2b
Electrostatics
A potassium ion and a chlorine ion are separated by a membrane, yet they exert
an attractive force F on each other. When the membrane is three times thicker,
the attractive force is F'. What is the ratio of F to F? (Note: Neglect force interactions with the membrane and surrounding solution.)
9:1 B. 3:1 C. 1:3 D. 1:9 A.
Solution
Ascharges grow farther apart, the force they exerton one another decreases, so F is greater than F'. The ratio of F to F' is greater than 1.This eliminates choices C and D. Because the force depends on the distance squared, tripling the distance
will affect reduce the force by a factor of nine. The ratio of F to F is 9 :1.
The best answer is choice A.
Example 83a
What is observed over time after a +1 charge and -1 charge initially 2.0 cm apart
are released from rest?
A. B. C. D.
They move towardsone anotherat constant v along a straight line. They move towardsone another with an increasing v along a straightline. They move towardsone another with a decreasing v along a straightline. They both move in the same linear directionwith the samespeed.
Solution
Because theyare oppositely charged, they willaccelerate towardsone another, so choice D is eliminated. As they draw closer to one another, the force increases, so
the move towards one another with increasing acceleration and increasing speed.
The best answer is choice B.
Example 8.3b
Solution
The force depends on the magnitude of each chargeand the distance between the particles squared. Lefs compare each choice one-by-one to a designated choice, starting with choice B to choice A. Choice B has one charge that is doubled that
of choice A, but the distance is also doubled. Doubled distance reduces the force
by a factor of four, which outweighs the greater charge. Choice A feels a stronger
force than choice B, so choice B is eliminated. Now lefs compare choice C to choice A. Choice C has both charges double that of choice A, but the distance is tripled. This would reduce the force by a factor of nine, which outweighs the impact of greater charges, so choice A feels a stronger force than choiceC. Choice C is eliminated. Last, lefs compare choice D to choice A. Choice D has both charges triple that of choice A, but the distance is quadrupled. This would reduce the force by a factor of sixteen, which outweighs the impact of greater charges, so choice A feelsa stronger force than choice D. ChoiceD is eliminated.
The best answer is choice A.
119
Physics
Electric Fields
Electric Fields Consider that a single charge by itself feels no electrostatic interactions until a second charge is near. By itself, there is nothing more than a potential to feel a
force if a second charge were moved into its vicinity. An electric field is a region
of space where a charged particle would feel an electrostatic force, if it were moved there. This imaginary charge is referred to as a test charge (denoted as q'). Electric fields can be made of a single charge or several charges. It is simply the region of space where a test charge would feel an electrostatic force if added.
Suppose we do not know how unknown charges are distributed in space. One
way to probe for a charge distribution is to use a test charge. Let's assume that the unknown charges are arranged under a box, as shown in Figure 8-3. We then take a test charge, which is positive (a negative test charge could work as well, but by convention test charges are considered to be positive), and place it in the
region of space near the box. We have presented three arbitrary positions in Figure 8-3. If the test charge is attracted to some region of the box, then it means that there is a negative charge in that vicinity. Similarly, if the test charge is repelled from a region of the box, then it means that there is a positive charge in that vicinity. If we apply this type of analysis to every point outside the box, we can determine the nature and location of the charges under the box. These forces
constitute an electric field E. The unit of an electric field is the newton/coulomb.
//
Figure 8-3
If we were to sum up all of the force vectors associated with Figure 8-3, then we would get a picture as shown in Figure 8-4. The lines are referred to as field lines
(although you'll note that most of them bend). These lines represent the
orientation and strength of the electric field.
Figure 8-4
An electric field at a given point in space is defined by equation (8.2). The electric
field E is the ratio of the net electrical force F acting on a test charge in a particular region of space, divided by the value associated with the test charge q'. Since the force is a vector quantity, so is the electric field. Because physicists have chosen test charges to be positive (+) by convention, electric field lines always point in the direction that the net force would act on a positive (+) test charge.
E= * q' Copyright by The Berkeley Review
120
(8.2)
Physics
Electric Fields
Field Lines Electric fields are often represented by lines of force or field lines. The field lines
show the direction of the electric field at every point in space, and they never intersect. This can be seen with the field lines in Figure 8-4. Field lines always originate on a positive charge and end on a negative charge. They represent the waya (+) charge would migrate. If the field lines are close together, it meansthat
apart, themagnitude ofthe electric field is weak. Two representative examples of
electric field lines associated with point charges are shown in Figure 8-5.
the magnitude of the electric field is strong. Similarly, if the field lines are far
Figure 8-5
net
Figure 8-6
What are the forces acting on the positively charged ion? First, there is an attractive force (F.) generated by the charge of the negative electrode. Second, there is a repulsive force (F+) generated by the charge of the positive electrode. In order to find the net electrical force on the positively charged ion, we sum the force vectors. Since only the net electrical force ultimately determines the motion of the test charge, we find that it moves toward the negatively charged electrode. Equation (8.2) applies here, although it might be easier to see it as Fe = qE. Copyright by The Berkeley Review
121
Physics
Electric Fields
Example 8.4a
Which of the following electric field configurations describes the lines of force in an electric field between two parallel plates of opposite charge?
A.
+ + + + + + + + +
B.
Ji M
1 u y v y v ]|
+ + + + + + + + + + + + + + + + + +
Solution
An important point to remember about electric fields is that they emanate from positive charges and point towards negative charges (they point in the way a positive charge would migrate). This means that choices A and C are incorrect.
Next, we must judge the straightness or curvature of the lines between the plates.
Imagine a point placed directly between two parallel plates. It will have a net
electric field determined by all the individual electric fields generated by every charge on the two plates. If these field lines are added vectorially, then all the horizontal components will cancel each other out; a net field oriented vertically downward will remain. The cancellation is due to the symmetry of the point in space with respect to the plate charges. However, this horizontal component cancellation continues only until one approaches the left and right edges of the plates. Here, the field lines bow out, like those around a dipole (the parallel plates are like several dipoles positioned next to each other). Between parallel plates of opposite charge, the field lines are straight and constant in strength throughout the interplate region. Thus, a parallel plate arrangement is a good design for capacitors,electrophoresis equipment, and charge accelerators.
The best answer is choice B.
Example 8.4b
Which orientation of a uniform electric field can explain the pictured motion of an electron initially moving in a straight line from left to right?
A.
B.
C.
D.
Solution
The negatively charged particle is deflected down, so it must be feeling a force in the downward direction. But this question has a subtlety you must not forget, and that is the fact that an electric field line is based on how a positive charge would be accelerated. To deflect a negative particle down would require a field that would deflect a positive particle up. This describes choice C.
The best answer is choice C.
122
Physics
Equipotential Lines
Electric Fields
all points within an electric field sharing the same potential. Ifwewere to place a
test charge at any point along an equipotential line, we would find that the electric field does no work on that testcharge when it moved to another pointon the same equipotential line. Work is done on the test charge only if the electric field has a component tangent to the equipotential surface. This tells us that
equipotential lines and electric field lines are perpendicular to one another
(Figure 8-7). When test charges move in the direction ofa field line, theyare said
to move from higher potential to lower potential.
*-
-i
H-
X\ i
I-**
f {
1 1
1 1
i I I
y<
y'
yf
ii
ii
}'
y'
y f
' /r^^V.
Figure 8-7
Equation (8.3) gives the change in electrical potential energy APEq oftwo charges
in a vacuum, as they are moved from some initial separation r{ to some final
separation rf. This equation supports the general rule regarding the potential energy of a system. It always decreases as the system approaches some equilibrium state. Opposite charges naturally attract; as they approach one another, their potential energy decreases. The reverse applies when two like chargesare brought towards each other.
APEq =kq,*(-JL)
potential energy.
(83)
Generally speaking, if you must do work to move the charged particles, then they've been moved to a state of higher electrical potential energy. If the charged particles move naturally, then they have moved to a state of lower electrical
123
Physics
Electric Fields
Electrical Potential Difference As charged particles move through space, they encounter other charged particles. Each of these charged particles creates a little electrical environment
that influences charges in its vicinity. A chargedparticletends to move towardsa
region of space where its electrical potential energy decreases (much like water flowing downhill to a region of lower gravitational potential energy). The electrical potential difference a moving charged particle is subjected to as it
moves from some region A to some region B (denoted as Vab) is the difference in electrical potential energy APEq at those two regions, divided by the value associated with the charged particle q. Thisis shown in equation (8.4).
APEAB_PEqB-PEqA_APEqAB
q q q
The unit of charge is the coulomb C and the unit of electrical potential energy is the joule J, so the final result of equation (8.4) gives us units of joules divided by coulombs (or J/C). A joule divided by a coulomb is defined as a volt V, the unit of electrical potential difference. A more common version of equation (8.4) is equation (8.5). It calculates the change in electrical potential energy as a charged particle moves through a voltage difference:
APEq = qV
(8.5)
Absolute Potential When doing electrical calculations, it is often useful to have a point of reference. That point of reference in electrical circuits is referred to as the ground point. By definition,the voltageat the ground point is zero. Measuring the voltage at other points in space relative to the ground point describes an absolute potential.
Example 8.5a
An electron gun usually consists of two electrode plates, one more negatively charged than the other. If an electron of mass m is allowed to accelerate between
the two electrodes separatedby a voltage V, which equation BEST represents the final speed of the initially stationary electron upon striking the more positive
electrode?
A. v=*pEL
V:2eV
B. v=\l*&m
C.
D.
v=V -v
v =
-./mV
2e
2e
mV
Solution
Let's answer this question in two ways: using physical intuition and energy conservation. First, physical intuition. How will m, e, and V affect the electron's final velocity? The potential difference supplies the energy to accelerate the electron. If mere is a bigger voltage, the electron should get more energy and, hence, more speed. Because speed depends on the voltage, V should be in the numerator, eliminating choices A and D. The final speed should be greater for lighter particles (since it has less mass to accelerate). Therefore, the mass should be in the denominatorcross out choices A (again) and C. Only choice B has V in
the numerator and m in the denominator, so it is the best answer. Notice that we
124
Physics
Electric Fields
don't even need to think about where the e should go. When approaching
questions in this way, always start by thinking about the physical variable that makes the mostsense to you.The particularstartingpointis up to you.
Let's use energy conservation to solve this problem. Identify the initial and final energies. Has any external work is done on the electron? Finally, plug into: ^initial ofobject + "0n object = Efinal of object
does work on the electron. This work and the kinetic energy fit into the energy
conservation equation as follows:
Solving for the speed v gives choice B. Using energy conservation is a powerful
technique. Energy conservation does not require us to know about the nature of the interactions (be they mechanical, gravitational, thermal, or electrostatic). It is concerned only with the energies. Whenyou are in doubt about how to approach a problem analytically (i.e., using equations), try energy conservation first. This particular problem type is a popular one. Many scientific machines and natural eventsinvolve chargesaccelerating through a potential difference.
The best answer is choice B.
Example 8.5b
An ionic surfactant molecule is a long, carbon-based polymer with a charged end. If the uncharged end is attached to a plate and the molecule is immersed in an electric field, what is the maximal amount by which the molecule would stretch? (Assume that interactions with the plate and surrounding solution are negligible and that the molecule obeys Hooke's law with its spring constant k.)
A.
V 2qV
B.
x-/m:
x
C.
"V^q"
kV
_ /kV
D'X= 2q_ V
Solution
Intuition tells us that as the charge q increases, the force acting on the polymer will be stronger and the polymer should stretch more. This means that x increases as q increases, so q should be in the numerator. This eliminates choices A and C. As the voltage, V, increases, the force on the polymer also increases, so V should also be in the numerator as well. This eliminates choice D, leaving only choice B. The spring constant, k, should be in the denominator, because it hinders stretching. If you prefer to use conservation of energy, the equation is:
qV =Vfckx2. Solving forx will confirm thatchoice Bis the best answer.
The best answer is choice B.
125
Physics
Electric Fields
Dielectric Constant So far we have been considering charges in a vacuum, but they are also found in media. The effect that a medium can have on charges is taken into account by a
parameter called the dielectric constant K, which is the ratio of the electrical
force between two charges when they are in a vacuum compared to when they are in a medium. This is shown in equation (8.6). Dielectricbehavior results from a medium's polar nature, including its ability to assume an induced dipole.
'medium
F _j.
_ r vacuum
~
(8.6)
polar molecules, so that the net electric field within the medium becomes weaker
than the external field. This occurs when the 6+ charges of the medium align near the negative plate and the 5- charges align near the positive pate. Such a field strength reduction diminishes the interactive forces between all charges within the medium. Figure 8-8 shows the electric field associated with a parallel
plate capacitor before and after a polar medium has been added. The polar medium aligns in such a way as to offset, and in doing so, diminish the magnitude of charge on each plate.
6--6+6--6+6 6+6--5+
+10 +76'
+10
-10
+8ish
6 6+6-"6+6 6+5 6+ 66*6 6+6 6+6 6+ 6 6+6 6+6 6+6 6+ 66+66+56+66+ 6 6+6 6+6 6+6 6+ 6 6+6 6+6 6+6 6+
-10
+76* -8ish
p _ Fyacuum _ fclqiq2l
K
(8.7)
Kr
Equation (8.7) applies to charges separated by a distance r in a medium with dielectric constant K. Note that the smaller the value of K, the larger the force between charges.Table 8-2 provides a list of some common dielectricconstants.
^^^&|erial::.::,::;
Vacuum
Dielectric constant, K
1.0000
Dry Air
Paper
Benzene
1.0006
3.5
4.0 5-10
8
Glass
Axon membrane
(unmyelinated)
Water
80
Table 8-2
126
Physics
Electric Fields
temperature. What can explain the sharp rise and subsequent slow decay of Kas
the temperature increases?
A. The solid material melts at Ti, increasing its polarizability. Thermal motion
subsequently increases its polarizability.
B. The solid material melts at Ti, increasing its polarizability. Thermal motion
subsequently reduces its polarizability.
Materials that are polar, or that are able to polarize easily (i.e., have an high polarizability), typically have stronger dielectric properties than nonpolar
materials. The basic relationship between polarizability and the dielectric constant is the following: If the polarizability increases, then the dielectric constant increases. With this in mind, we need to consider what impact a change in temperature would have on the polarizability of a material. The first thing to consider is the drastic increase in polarizability at Ti- Choices C and D state that the gaseous element ionizes at temperature T\. Ionization would decrease the polar nature of the gas, as the gas would become canonic and thus lack a negative pole. This eliminates choices C and D. It must be due to melting. As a material melts, its polarizability increases, because the molecules can more easily orient themselves in the liquid state than they can in the solid state (where they exist in a crystal lattice). For example, H2O is a relatively polar molecule. In the solid state, water (ice) molecules point in many directions. Thus, an external
electric field will not be reduced much within the ice, because the net electric
field of the molecules is zero. As liquid water, the molecules can more easily
orient themselves in much the same direction when an external electric field is
present; the net field of the molecules in no longer zero, and the total electric field within the water is reduced. This makes the induced polar properties of liquid water greater than those of ice (i.e., K increases when ice melts). From this point, ifs a matter of observing the trend more so than evaluating the reasons for the trend. As the temperature continues to increase, the thermal motion of the molecules increases. According to the graph, as the temperature increases from Ti, the polarizability decreases. This means that as the temperature increases, the polarizability of the material decreases, making choice B the best answer. Continuing with the water example, when water heats up, thermal motion disrupts this polar alignment, and K decreases.
The best answer is choice B.
127
Physics
Electric Fields
Two experiments measure the electrostatic force between two cationic particles
in different media, A and B. What is true of the two media?
Example 8.6b
A. B. C. D.
Medium A has more positive charges than Medium B. Medium Bhas more positive charges than Medium A. Medium A has a larger dielectric constant than Medium B. Medium Bhas a larger dielectric constant than Medium A.
Solution
The electrostatic force between the two cationic particles is reduced in medium B
relative to medium A. Based on the possible answer choices, it is either caused by a difference in the number of positive charges in each medium or a difference in the dielectric constants of the two media. The presence of positive charges in the medium would not impact the force between two particles, although it would
impact the net force. This is because the force vectors in a charged environment can all be treated as independentof one another. This eliminates choices A and B.
The difference in the forces must be due to the dielectric nature of the two media.
According to equation (8.6), as the dielectric constantincreases, the force between two charged particles decreases. The graph shows that the force is less in
medium B than in medium A, so medium B must have a greater dielectric constant than medium A. Physically, this means that medium B is more polar than medium A and that it can reorient itself to reduce the strength of the electric field between the two charged particles.
The best answer is choice D.
Electric Dipole
An electric dipole is established when two charges of opposite signs are separated from one another by some distance L (Figure 8-9).
Figure 8-9
An electric dipole moment can then be defined by equation (8.8), where p is the dipole moment (a vector quantity), q is the product of the charge, and L is the distance separating the charges.
P = qL
(8.8)
What happens when we place this electric dipole in a uniform electric field, as
shown in Figure 8-10?
128
Physics
Electric Fields
F. = -qE
-q
LcosO
Figure 8-10
From equation (8.2), we know that the force F+ has a magnitude +qE, while the force F- has a magnitude -qE. Adding these forces together, we find that the net
force on an electric dipole in a uniform external electric field is zero.
However, note that the forces have different lines of action. This means that the
net torque on an electric dipole is not zero. In Figure 8-10, the torque is directed into the page. The dipole will therefore rotate clockwise until it linesup with the field. If we let the angle between the dipole axis and the electric field be 0, then the torque created by the dipole couple can be quantified by equation (8.9).
x = (qE)(Lsin 0) = (pE)(sin 6)
(8.9)
The torque is at its minimum when p and E are parallel (or antiparallel) to one another (Figure 8-lla). The torque is at its maximum when p and E are perpendicular to one another (Figure 8-llb).
(a)
(b)
-q
L
e
+q
^
-q
*
l<
^Figure 8-11
If the dipole were to change directions in an electric field, not only would work be performed, but there would also be a change in potential energy (PE). If 0 = 90 in Figure 8-10, the electric dipole would be perpendicular to the electric field (see Figure 8-llb). In this case, the potential energy of the system is zero. If 0 = 0, the electric dipole would be parallel to the electric field (see Figure 8-lla). The potential energy of this system is at its most negative value (i.e., the stablest value). If 0 = 180, the electric dipole would be antiparallel to the electric field and the potential energy would be at its most positive value (i.e., the most unstable value). The potential energy of the system can be given by equation
(8.10).
PE = - (pE cos 0)
(8.10)
129
Physics
Electric Fields
Example 8.7a
A. B. C. D.
to a clockwise torque and a net linear acceleration. to a counterclockwise torque and a net linear acceleration. to a clockwise torque and no net linear acceleration. to a counterclockwise torque and no net linear acceleration.
Solution
Use the multiple-concepts approach. If a dipole is placed in an external electric field, it can possibly experience a torque. The positive charge in the dipole is tugged to the left, and the negative charge is tugged to the right; the dipole rotates. If forces cause an object to rotate, there must be a torque on it; here, the torque is clockwise. Thus,choices Band D are wrong.
Regarding a net linear acceleration, ask yourself whether there would be a net force on the dipole. The positive charge experiences a force F = qE to the left. The
negative charge experiences a force to the right. However, the force on the
negative charge is bigger. Why? The charges have the same magnitude, but the electric field is indicated as being stronger to the right in the picture (remember, closer lines mean a stronger field). As the dipole rotates, the negative charge will be in a stronger electric field. The dipole will experience a net force to the right, and consequently a net accelerationto the right.
The best answer is choice A.
Example 8.7b
Which of the following configurations of dipoles would produce the GREATEST electrostatic potential energy?
A. B.
<&
C.
D.
Solution
By symmetry, choices A and B are equal in magnitude, so both systems should share the same electrostatic potential energy. This eliminates choices A and B. The best way to solve the question from this point is to consider how stable the two remaining choices appear. Choice D has like charges apart and opposite charges close, while choice C has like charges close and opposite charges apart.
Choice D is more stable than choice C, which means it has less electrostatic
potential energy (more stable implies less potential energy). A greater amount of electrostatic potential energy is found in choice C than choice D.
The best answer is choice C.
130
Physics
Electromagnetism
Electromagnetism
In our study of electrostatics, we found that electric charge can create an electric field in the space surrounding the charge. We also saw that this electric field exerts a force on any charge present within it. A charge moving through space also creates a magnetic field capable of exerting a force on any other charge moving in that field. Magnetism arises from charges in linear or radial motion.
Magnetic Fields
A magnetic field has a magnitude and a direction. Magnetic fields are denoted by the symbol B, and they are vector quantities. The SI unit for a magnetic field is the N's/C'm. When we study currents, we will see that an ampere A is a coulomb per second. Substituting the SI nomenclature, we have the unit N/Am, a unit called the tesla (denoted as T). The CGS unit of the magnetic field is the gauss (denoted as G). The relationship between a gauss and a tesla is that 1 G =
10"4 T. Magnetic field strengths vary greatly for different natural phenomena:
The Earth's magnetic field has a strength of about 0.5 G at the Earth's surface; an
everyday refrigerator magnet has a strength ofabout 10"2 T; and an MRI field has
a strength of a few teslas.
Magnets have both a north pole and a south pole. The north pole of one magnet attracts the south pole of another magnet, and vice versa. Poles of like orientation, however, repel each other when placed close together. Magnets generate magnetic fields, which can be represented on paper in much the same way that we represented electric fields. The vector-like lines of the magnetic field show the direction of that field at a given point in space; tighter line densities
indicate stronger magnetic field regions. Magnetic field lines always form closed
loops. Because of this natural property, bar magnets are always dipolar (i.e., there is always a north and south pole). This is unlike electric field lines, which can emanate from a single charge (i.e., a monopole). However, by convention we say that magnetic field lines emanate from the north pole and re-enter through the south pole, as shown in Figure 8-12.
Figure 8-12
Magnetic fields can exert a magnetic force Fmagnetic on a charge moving in that
field. If a charge q is moving with a velocity v through a perpendicular magnetic field B, then the magnitude of the magnetic force is given by equation (8.11). The moving charge experiences a force that is perpendicular to both v and B. It is the component Bj^ of the magnetic field perpendicular to the velocity v that dictates the size of this force. Therefore, equation (8.11) can be rewritten as equation (8.12). The angle 0 in equation (8.12) is the angle between v and B.
Fmagnetic = qvB
(8.11)
Fmagnetic = qvBsin 0
Copyright by The Berkeley Review
131
(8.12)
Physics
Electromagnetism
As shown in Figure 8-13(a), the force is greatestwhen the velocity of the charged particle is at right angles to the magnetic field (i.e., when sin 8 = 1).As shownin Figure 8-13(b), the force is smallest when the velocity of the charged particle is parallel or antiparallel to themagnetic field (i.e., when sin 0 = 0).
(a) (b)
Fmagnetic =qvB(sin 0) =0
Figure 8-13
While equations (8.11) and (8.12) can tell us about the magnitude of the magnetic forceacting on a moving charged particle, we need to employ the right-hand rule to determine the direction of the magnetic force. As far as getting prepared for the MCAT goes, this is the most important concept to master in this chapter. The right-hand rule assigns three different parts of our right hand to represent each of the three mutually perpendicular vectors associated with a charged particle moving through a perpendicular magnetic field (as shown in Figure 8-13(a)). There are several versions of the right-hand rule taught to physics students around the world, so while we will choice one to use repeatedly in this section, if you have learned and mastered a different version, please use the one that works best for you. Keep in mind that all the right-hand rule is doing is helping us to visualize three mutually perpendicular vectors. In our first application of the right-hand rule, we shall consider the charged particle in Figure 8-13(a). We will use our thumb to represent the velocity of a (+)-charged ion in linear motion, our fingers to represent the direction of the magnetic field vectors, and our palm to represent the direction of the resultant magnetic force. It is important to note that the right-hand rule is based on the motion of a positively charged particle, be it a single cationic charge moving through space or a current of positive charges flowing through a wire. There is a magnetic force associated with a negatively charged particle moving through a perpendicular magnetic field, it just points in the opposite direction of what the right-hand rule shows.
In Figure 8-13(a), a cationic particle is moving in the plane of the magnetic field from the bottom to the top, so we point or right thumb to the top. Next, with a flat, open hand and your thumb perpendicular to your index finger, point your remaining four fingers in the direction of the B field, which is from right to left in this case. With your thumb pointing to the top and your fingers pointing to the left, your open hand is "palm up", which means that the magnetic field is pointing up (the direction you'd push the charge with your palm. It is helpful to keep in mind that your right hand is simply serving as a model for the three perpendicular axes. In this case, the axes are bottom-to-top (velocity), right-toleft (magnetic field, and below-to-above (magnetic force). We shall do a few examples, because the right-hand rule is mastered only through practice. We shall create a systematic checklist of the three axes in selected examples.
The Berkeley Review
132
Physics
Example 8.8a
Electromagnetism
If a cation enters into magnetic field from the top (as pictured below), in which directionwill the cation be deflected while traveling through the magnetic field?
t 3) TO
A. To the left
To determine the direction of the magnetic force deflecting the cation, and thus
the direction in which the cation will be deflected once in the field, we need to
use the right-hand rule. When using the right-hand rule, keep in mind that it is used to determine the direction of the magnetic force on a positively charged particle in motion, which is the case here. The velocity is from the top to the
bottom, sopoint your thumb downward (thumb = down, not up; |down| up). The
magnetic field is orientedout of the page, so whilekeeping your thumb pointing
down point your fingers out from the page (fingers = out, not in; ^u| m). Once
you've done this, you'll see that your palm points to the left (palm = left, not
right; Jef^ right). Because your palm points to the left, we know thatthemagnetic force on a positively charged particle points to the left. This will deflect the cationic particle to the left once it has entered the magnetic field.
The best answer is choice A.
Example 8.8b
Which combination of cation in motion and magnetic field will result in the cation being deflected out from the page?
A. B.
I
*
Jr
I
y
D.
v
c
133
Physics
Electromagnetism
To determine which particle will get deflected out of the page, we need to apply the right-hand rule to each of the four choices. Choice A: The velocity is from the right to the left, so point your thumb to the left The magnetic field is pointing down, so point your fingers down. Aligned as such, your palm points out from the page. The magnetic force deflects the cationicparticle out from the page, so choiceA is valid. Choice B: The velocity is from the left to the right, so point your thumb to the right The magnetic field is pointing out from the page, so point your fingers out. Aligned as such, your palm points down. The magnetic force deflectsthe cationic particle down, so choice Bis invalid. Choice C: The velocity is from the bottom to the top, so point your thumb up. The magnetic field is pointing into the page, so point your fingers into the page. Aligned as such, your palm points to the left The magnetic force deflects the cationicparticle to the left,so choice C is invalid. Choice D: The velocity is from the bottom to the top, so point your thumb up. The magnetic field is pointing to the right, so point your fingers to the right Aligned as such, your palm points into the page. The magnetic force deflects the cationicparticle into the page, so choiceD is invalid.
The best answer is choice A.
Example 8.9a
An electron moves from left to right (on the page) through a uniform magnetic field. Which orientation of a uniform magnetic field would result in the smallest magnitude of force acting on the electron? A.
Solution
B.
X X
X X
C.
"^
F = qvBj.
To find the direction and magnitude of magnetic forces, use the right-hand rule when considering directions,and use:
when considering magnitudes. Lefs start by consideringthe terms. Eachanswer choice involves a moving electron, so q and v are irrelevant. Only the magnetic
field orientation, Bj_, varies between the answer choices. Recall that B is the
componentof the magnetic field perpendicular to the charge'svelocity. We want the choice where theBfield is leastperpendicular to the particle's velocity.
In choice A, both the velocity of the particle and the magnetic field are pointing in the same direction, so the choice with the smallest component of B is choice A. Choices B and C both represent a magnetic field that is perpendicular to the
particle's velocity, so choices B and C give the same magnitude of force, even though the resulting force directions will differ-this assumes that both choices have the same magnetic field strength. Choice D shows a B field that is neither perpendicular to nor parallel with the particle's velocity, so the force on the charged particle will have a magnitude somewhere between zero and qvB (the maximum force possible). To determine the exact value, we would need to multiply the magnitude of the B field by sin8.
The best answer is choice A.
134
Phy S1CS
Example 8.9b
Electromagnetism
If an electron travels to the right in the magnetic field pictured below, in which direction would the net force on the electron be pointing?
xxxxxxxxxxxx
X X XX XX xxxxxxxxx xxxxxxxxx
xxxxxxxxxxxx
B.
C.
D.
M
Solution
To determine the direction of a magnetic force, we need to use the right-hand rule. However, the right-hand rule is used to determine the direction of the magnetic force on a positively charged particle in motion, not a negatively charged particle. For this question we will need to reverse the answer we get using our right hand. The velocity is from the left to the right, so point your thumb in to the right (thumb = right, not left). The magneticfield is oriented into the page, so point your fingers into the page (fingers = in, not out). Once you've done this, you'll see that your palm points up to the ceiling or sky (palm = up, not down). Because your palm points up, we know that the magnetic force on a positively charged particle points upward. The magnetic force on an electron must be pointing downward. Only choice B shows this.
The best answer is choice B.
Examples 8.8a through 8.9b emphasize a few concepts. First, thereis the fact that magnetic fields are generated by charged particles in motion and that two such magnetic fields when aligned correctly (perpendicular to one another) can generate a force. Second, the direction of the magnetic force caused by the
interaction of a charged particle in motion with an external B-field can be obtained using the right-hand rule, a technique for determining the alignment of three perpendicular vectors.
Let's apply this concept to a conducting rod moving through an external magnetic field. Because the rod is conducting, it has loose charges that can migrate through the rod if a force is applied. The impact on each individual charge will be the same as we observed in Example 8.8b, so they will all migrate.
However, because the charges are bound to the conducting rod, they can only migrate along the rod. Figure 8-14 showsthisbehavior.
x 5+ x x
X
x v x
t
e
X X
0- X
135
Physics
Electromagnetism
Lenz's law takes the example shown in Figure 8-14 and applies it to a conducting loop instead of a conducting rod. As a consequence, the charges do not reach a dead end at the ends of the rod, and instead are able to flow completely around the loop. The result is that the magnetic force can induce a current in the conducting loop. What we learn is that the loop only experiences an induced current when it is entering or exiting the magnetic field. The exact wording of
Lenz's law is as follows:
As worded above, the law doesn't necessarily make sense at first reading. Heck, reading it a second or third time doesn't really help either. To make things easier to understand, lefs compare Lenz's law to Le Chdtlier's principle. Consider the system shown in Figure 8-15. As the loop moves into the field, it experiences a gain of Xs within the inside of the loop. According to Le Chdtlier's principle, if a chemicalsystem at equilibriumgains reactants, then it shifts to make products; if the equilibrium system gains heat, then it shifts in a way to absorb neat (make cold). The system shifts in a way to reduce the stress. The same is true with Lenz's law. The stress is that the loop is gaining Xs within the loop as it enters the field shown in Figure 8-15, so it must generate the opposite of an X. Given
that an X represents a magnetic field going into the page, the loop will experience an induced current that creates a magnetic field coming out of the page within the loop. According to the right-hand rule for magnetic fields emanatingfrom current carrying wires, a magnetic field pointing out of the page occurs with a counterclockwise current. Hence, as the loop enters the field at t =
1, it experiences a counterclockwise, induced current.
y.
j<
x.x>x
j<
Xs
Jk
t = 0 No current
t = l
t = 2
t = 3
t = 4
Counterclockwise
current
No current
Clockwise
current
No current
change in the number of Xs inside the loop). However, when the loop leaves the field, it experiences a drop in the number of Xsinside the loop.To offset this loss
in Xs, an induced current in the loop is generated in such a direction that it creates a magnetic field going into the page. According to the right-hand rule, this occurs with a clockwise current. This is why as the loop exits the field at t = 3, there is a clockwise, induced current. Hopefully taking a Le Chatelier's perspective on Lenz's law simplifies it.
136
Physics
Electromagnetism
The magnitude of the current depends on the rate at which the flux changes. This is known as Faraday's law, equation (8.13), which states that the em/causing the induced current is proportional to the rate of change of the flux within the loop.
Faraday's law
em/=.AOB/At
(8.13)
Faraday's law explains that as you increase the rate at which the loop enters a B field, the magnitude of the induced current increases, as shown in Figure 8-16.
Slower immersion
Faster immersion Clockwise current
_j
Figure 8-16
;I
Example 8.10a
What is true of a conducting loop that spins within a magnetic field about an axis perpendicular to the magnetic field? A. It experiences an induced alternating current. B. It experiences an induced direct current of constant magnitude. C. It experiences an induced direct current of changing magnitude.
D. It experiences no current.
Solution
As the loop rotates about an axis that is perpendicular to the magnetic field, it gains Xs some of the time followed by a period of time where it loses Xs. This
means that the current could be either counterclockwise or clockwise at different
pointsin its revolution, so the current is alternating. To generate a direct current, the loop would need to always be entering or always be exiting the field, which is physically impossible. Spinning loops in an external magnetic field generate induced, alternatingcurrents.This is the principlebehind electrical generators.
The best answer is choice A.
Example 8.10b
A metal loop movingleft to right across the following Bfield would induce a:
00000000
0000000 00000000
A. B. C. D.
clockwise current once it was fully immerse in the field. counterclockwise current once it was fully immerse in the field. clockwisecurrent upon entry and a counterclockwise current upon exit. counterclockwise current upon entry and a clockwise current upon exit.
Solution
An induced current only occurs upon entering or exiting the field, so choices A and B are eliminated. Upon entering the field from the left, the loop would experience a gain in dots, which would induce a clockwise current to generate Xs.
The best answer is choice C.
137
Physics
Electromagnetism
A solenoid is a helical winding of a conducting wire, such as a coil of copper wire wound on a cylindrical tube. A solenoid should have a length that is at least four times its radius. Upon passing current through a solenoid, a magnetic field can be generated that depends on the magnitude of the current and dimensions of the solenoid. A solenoid can serve as an electromagnet when a constant direct current generates a steady magnetic field of fixed strength and orientation. Figure 8-17 shows a solenoid and a corresponding graph relating the strength of the magnetic field to the position in the solenoid. The n0 term is a constant for magnetic fields, n is the number of turns in the solenoid, and J is the current.
Figure 8-17
is passed around a conducting loop, causing a local magnetic field within the
it feels a torque and it is free to rotate, then the torque will cause it to rotate. Equation (8.14) describes the torque on the loop, where N is the number of turns,
loop. Ifthe loop is placed ina linear external magnetic field at such an angle that
field, and $ isthe angle between the external field lines and the loop's field lines.
x = NL4Bsin<j>
(8.14)
Iis the current, Ais the area of the loop, Bis the strength of the external magnetic
feeling some magnitude of torque. The result is that the symmetric collection of loops spins. Figure 8-18 shows one loop in an external magnetic field.
External B field Induced B field
Figure 8-18
138
Physics
Velocity Selector
Electromagnetism
Amongst the differences between an electric force and a magnetic force is that only the electric force can accelerate a charged particle from rest (speed up or slow down a particle for that matter) and only the magnetic force depends on the speed of the charged particle in motion. For this reason, electric fields are found in particle accelerators. However, the combination of an electric field and magnetic field, when aligned correctly, can serve to segregate particles of
different velocities. By arranging an electric field perpendicular to a magnetic field the right way, an electric force can be aligned in the opposite direction of the magnetic force. Figure 8-19, shows the basic schematic of a velocity selector where the electric field points down and the magnetic field points into the page.
E Travels straight
*"V=B"
Fdown = FE = qE
v<
ifFB =FE
Mass Spectrometer
A mass spectrometer takes advantage of the deflection of a moving charged particle in a perpendicular magnetic field. Once a charged particle enters a magnetic field, it will move in a circular path at a constant speed. The radius of the circular path depends on the mass of the particle, amongst other things. If all other factors are equal, then the relative masses of particles in the spectrometer
will correlate to their relative radii. Heavier particles traverse bigger circles and
thus have a greater radius. The correlation between the radius and mass can be
/qB
(8.15)
Figure 8-20 shows the top view of the three regions of a Bainbridge mass spectrometer. The multiple semi-circle curves representdifferent cations.
X = B field into page
+
Collision Detector
X
+
X
X
*x
X
+
+ +
>x
X X
X X
!
Region I
acceleration
x ir
ir
,r
ir
Region III
deflection
(F = qvB sin6)
139
Physics
Electromagnetism
In a velocity selector, which of the following changes will lead to an increase in the speed of the exiting particle? A. B. C. D. Decreasing the mass of the particle being ejected. Increasing the mass of the particle being ejected. Decreasing the strength of the electric field. Increasing the strength of the electric field.
Solution
In a velocity selector, the particle that travels straight through and thereby escapesthe velocity selector, has a speed v = E/B. In order to increase the speed of the ejected ion, either the magnitude of E must increase or the magnitude of B must decrease. Changing the mass of the particle will change the speed of the particle, but not the escape speed. All that will occur with a change in mass is that it will be different cationic particles that achieve the correct exit speed.
Choices A and B are eliminated.
Because the exit speed is v = E/B, a stronger E field, rather than a weaker E field, would result in a greater exit speed.
The best answer is choice D.
Example 8.11b
In a Bainbridge mass spectrometer, what could explain a greater radius of curvature in the deflectionregion for one cation versus a second cation?
A. An isotope of the element with fewer neutrons was used for the second
cation.
B. The electric field in Region I was decreased. C. The magneticfield in RegionIII was increased. D. A less ionized particle was used for the second cation.
Solution
a particle with a larger mass, a greater speed, a reduced charge, or the magnetic
field could havea diminished strength.
curvature, so choice A is eliminated. If the magnitude of the electric field in Region I weredecreased, then the particles leaving Region I would have a lower average speed. However, because of the velocity selector in Region II, the particles leaving Region II wouldhave the same speed, so the radii should not be
affected byspeed. Choice Bis eliminated. If the magnitude of the magnetic field in Region III were increased, then the particles leaving Region II experience a stronger deflecting force and be bent more. Because radius is inversely proportional to the magnetic field strength (r 1/B), a stronger B field would
result in a smaller radius. Choice C is eliminated.
A less ionized particle means that the cation has a lower magnitude of charge. If the second cation has a reduced q, then it will feel less ofa force deflecting it in
Region III, and thus, it will traverse a greater circular radius. This is because radius is inversely proportionalto charge (r 1/q).
The best answer is choice D.
140
I.
Electromotive Force
(1-7)
(8 -14)
(15 - 22)
II.
III.
(23 - 25)
The main purpose of this 25-question set is to serve as a review of the material presented in the chapter. Do not worry about the timing for these questions. Focus on learning. Once you complete these questions, grade them using the answer key. For any question you missed, repeat it and write down your thought process. Then grade the questions you repeated and thoroughly read the answer explanation. Compare your thought process to the answer explanation and assess whether you missed the question because of a careless error (such as misreading the question), because of an error in reasoning, or because you were missing information. Your goal is to fill in any informational gaps and solidify your reasoning before you begin your practice exam for this section. Preparing for the MCAT is best done in stages. This first stage is meant to help you evaluate how well you know this subject matter.
Passage I (Questions 1 - 7)
1.
For the moving rod in Figure 1, where are the electrons likely to cluster? A. At the top.
B. In the middle.
In order to produce a current in an electric circuit, a potential difference or emf (electromotive force) is required. This emf may arise from a chemical process, an external electric field, or magnetic induction. Dragging a conducting rod through a magnetic field induces an em/between the ends
of the bar:
C.
At the bottom.
X
X X
2.
X
X
How much work is done on an electron in moving it across the bar in Figure 1?
A. 0
B. ^
X
X
C. evLB evB
L
Figure 1
I).
This induced emf is given as: e = BLv, where B is the magnetic field, L is the length of the bar, and v is the speed
of the bar. e is measured in terms of volts. This method of
3.
The likely explanation for the induced emf shown in Figure 2 is an increasing: I. II. III. IV.
A.
X
X
X
X
X X
magnetic field as the rod moves to the right. area as the rod moves to the right. circuit resistance as the rod moves to the right. power loss in the resistor as the rod moves to the right.
II only
Figure 2
Faraday found that in general, an induced emf can be produced by changing a quantity called magneticflux:
(j> = BiA
4.
where B is the strength of a magnetic field passing perpendicularly through an area A, enclosed by a wire loop. The rate at which this quantity changes:
At
A. B.
Counterclockwise Clockwise
C.
D.
determines the induced emf across the ioop. This induced emf then drives a current through the circuit, which produces its own magnetic field that opposes the initial flux change. A current moving through a magnetic field experiences a
force of magnitude:
F=ILB
5.
where Bi is the component of B perpendicular to the current I running through a region (or wire) of length L.
In the following problems, let L = 1 meter, B = 5 T, v = 2 m/s, and R = 4 Q. The electron's charge is given by -e.
A. B. C. D.
142
6.
Passage II (Questions 8-14) Electrophoresis involves the separation of charged macromolecules by the application of an electric field. The charged molecules in the field are subjected to an electrostatic force given by:
F = qE
where q is the charge of the molecule, and E is the electric
field.
B.
loop. C. move to the right, to maximize the magnetic flux through the circuit loop. D. remain stationary, to keep the magnetic flux through the circuit loop constant.
7.
Using a larger resistance with the same current Increasing the rod velocity. Increasing the magnetic field strength. Increasing the rod length.
Gel electrophoresis utilizes a gel-like matrix to separate macromolecules. This apparatus is an important tool in the study of DNA, a macromolecule that has an intrinsically negative charge due to the presence of phosphate groups. Not only can gel electrophoresis be used to determine the base sequence of a DNA polymer, but it can also be used to separate DNA polymers by size.
For many years after the introduction of gel electrophoresis, it was nearly impossible to separate whole chromosomes. However, in the mid-1980s a new approach was taken that allowed entire chromosomes to be separated by a technique called pulsedfield gel electrophoresis. Instead of applying one electric field to a gel containing DNA, two electric fields are set perpendicular to each other. Rather than running one electric fields continuously, the two fields are pulsed. One field is turned on for a short time and then turned
off. Next, the second field is turned on for a short time and
then turned off. If the pulsed fields have the same magnitude, same duration, and are set up as shown in Figure 1, the DNA will run in a vertical line down the gel.
Electrodes
Gel Box
Figure 1
The idea is that the fields pull the DNA first one way and then another way. The effect is the separation of large DNA strands that run in a straight line.
Chromosome Number
I
Size (kD)
198 311 1285 864
III
VII
XVI
143
In a typical experiment to separate chromosomes, the DNA is loaded into wells in an agarose gel. The gel is
then immersed in a tank that contains a buffer. The buffer is
11.
plates of capacitors, and the plates are arranged around the tank to produce the fields shown in Figure 1. A constantvoltage power supply is used to monitor both the constant voltage and the current through the buffer. The distance D that a particular chromosome will migrate through a gel is
related to the molecular size M of that chromosome by:
D = a-b(logM)
that
depend
on
the
8.
Which of the following changes will affect the migration rate of a given band of DNA through a gel? A. Increasing the plate separation while keeping the voltage constant. B. Decreasing the voltage across the plates while keeping the plate separation constant. C. Changing the gel viscosity.
D. All of the above.
12.
Before the introduction of gels to hold the DNA during the electrophoresis process, DNA was placed in a liquid sucrose density gradient. However, this was not successful in separating DNA by size. DNA molecules of different sizes tended to run as one indistinguishable
band. Why?
9.
Occasionally, the cooler breaks down and the temperature of the buffer increases by as much as 20C. Why does the current also increase?
A. All DNA fragments have the same charge. B. Diffusion causes DNA to clump together. C. The liquid sucrose density gradient neutralizes the effects of the applied electric field. D. Viscous drag forces generally increase with
increasing molecular size.
13.
D.
14.
as strong as Electric field B. An experimenter loads a gel as shown below, but is unable to get a run. How can this result be explained?
A.
B.
Gel Box
A. The bands ran diagonally off the gel's right side. B. The bands ran diagonally off the gel's left side. C. The bands ran in a straight line off the gel, from
top to bottom.
144
Passage III (Questions 15-22) A group of students decide to study electrostatics. They have the following items at their disposal: glass rods, hard rubber rods, silk, fur, metal rods with glass supports, and metal spheres on glass supports.
Experiment J The students attempt to demonstrate that there are two kinds of charge. First, they rub a glass rod with silk. This rod is hung from a long silk thread. A second glass rod is rubbed with silk and held near the rubbed end of the first glass rod. The two glass rods are observed to repel each other. Next, a
hard rubber rod is rubbed with fur. When the hard rubber rod
16.
In Experiment 1, suppose that the rubbed glass rod became positively charged. Then the silk that rubbed it
would:
A. acquire an equal amount of negative charge. B. acquire an equal amount of positive charge. C. acquire a positive charge, but not the same amount as the glass rod has. D. remain neutrally charged.
17.
In Experiment 2, why is it important that the glass rod not touch Sphere I? A. To maximize the amount of charge transferred to the sphere
B. To maximize the rate of charge transfer to the sphere
is held near the rubbed end of the glass rod hanging from the thread, the two rods are observed to attract each other.
However, two hard rubber rods rubbed with fur are observed
C. To prevent induction of charge separation onto the sphere D. To prevent charge transfer directly to the sphere
Two neutral (uncharged) and identical metal spheres on glass supports are brought close to each other but are not allowed to touch. A glass rod is rubbed with silk and the rubbed end is brought close to one of the spheres, Sphere I, but does not touch it (as shown below). With the glass rod still held near Sphere I, a conducting wire connects the two
18.
Upon completing Experiment 2, the students found: A. that both spheres have acquired the same type of charge as that found on the rubbed glass rod. B. C. that the spheres have remained neutrally charged. that Sphere I has acquired the same type of charge as that on the glass rod, and Sphere II has acquired the opposite type of charge.
glass rod
rubber end
D. that Sphere I has acquired the type of charge opposite to that found on the glass rod, and Sphere II has acquired the same type of charge.
19.
glass support glass support
In Experiment 3: A. the electrons flow continuously in the metal rod, as long as the glass rod is held near the metal rod.
Figure 1. Experiment 3
C. both
positive
and
negative
charges
flow
15.
How do the masses of the spheres in Experiment 2 compare before and after the experiment?
A. The masses remain the same.
20.
Suppose now the students repeat all of the experiments on a humid day. They find that:
A. the results remain unchanged.
well.
B. The masses of both spheres increase. C. The masses of both spheres decrease.
D. One mass increases, and the other decreases.
145
21.
A.
B.
23. A charged particle is suspended between two horizontally aligned parallel plates carrying opposite charges of equal magnitude. If the separation between the plates is doubled while the voltage is held constant, whathappens to the electricforce on a particulardrop?
A. B. It is doubled. It is halved.
Which of the following statements is NOT a valid description of the role of corresponding material in the
experiments?
A. Fur is used to transfer electrons to the material that
24. For a positively charged particle moving left to right through a linear magnetic field oriented into the page,
whatpath will be observedfor the particle?
C. The spheres serve to create electrons. D. The glass rods serve to transfer electrons to the silk cloth that is rubbed against them.
A. B. C. Path I Path II Path III
A.
C. the
D.
wires
rotate
such
that they
become
1.
2. C
7. D
3. A 8 D
4. A 9.
6. D 11. A
16. A 21. B
25. A
146
Choice C is the best answer. The electrons in the bar experience the magnetic force: F = qvB. The direction of the force can be determined using the right-hand rule. There are many versions of this, so use whichever one is familiar to you. If you do not know any right-hand rule, here's one: Hold your right hand flat, with your thumb perpendicular to your fingers. Your fingers point in the direction of the magnetic field lines (remember: many lines, many fingers). Your thumb points in the direction in which the charge moves (remember: hitchhiking charge). Your palm will, as a result, point in the direction in which the induced force would push a positive charge (remember: palms push positive charge). If the charge is negative, as it is in this case, just reverse the direction of the force. Here, the electrons are moving towards the right, and the magnetic field points into the page. Using your right-hand rule shows that the electrons experience a net force downwards and will cluster at the bottom of the rod. The best answer is
choice C.
2.
Choice C is the best answer. The work required to push an electron from one end of the moving rod to the other end is equal to the potential energy change:
W = AU = qAV
From thepassage, we are told that the induced emfacross theends of the bar is given by: e = BLv. The work required to move an electron is given by: W = BLve. The best answeris choice C.
3. Choice A is the best answer. As the rod is pulled along the rails, the area enclosed by the rod and the rails grows larger and
larger. The flux changes because the area changes, and the change in flux induces an emf, according to Faraday. This
validates choices A, B, and D. Since the magnetic field is not changing in the setup for Figure2, an increasing magnetic field is not the reason for the emf. This rules out choices B and D, leaving only choice A. Regarding statements III and rv, the resistance of the circuit does not change as the rod moves, because the only source of resistance is the resistor (which is
fixed). Therefore, assuming a constant emf, the overall resistance and power loss areconstant. The best answer is choice A.
4.
5.
Choice A is the best answer. Electrons will be pushed toward the bottom of the rod. Current, by definition, is the flow of
positive charges. Since the electrons flow clockwise, the current will flow counterclockwise. The best answer ischoice A.
Choice D is the best answer. From Ohm's law, we know that e = IR. Rearrangement of terms gives:
I = iL
R
Weare told in the passage that s = BLv. For this problem, wesubstitute as follows:
Choice D is the best answer. Let's start by considering A. Using the right-hand ruleon a current running through the wire in
Figure 2 shows you that the rod is pushed either to the right orto the left (depending upon the direction of the current). This
invalidates choice A. Magnetic flux does not tend to change. That is why, as stated in the passage, the current generated in a wire loop will orient itself sothat its magnetic field opposes the induced change in flux~a condition described by Lenz's law.
This invalidates choices B and C, and favors choice D. The best answer is choice D.
Choice D is the best answer. Asking which change will notreduce the power drain can be restated as asking which change will either increase the power drain or leave it unchanged. Power drains from in a resistor because a current moves through its resistive material, dissipating energy as heat. Increasing the resistance would therefore increase the power drain, making
Option I valid and choice C invalid. Increasing the rod velocity and magnetic field strength are both ways to increase the emf
induced across the circuit. This will increase the current and the resulting power loss, making only choice D valid. Notice
that increasing the rod length does not change the size of the rest of the circuit. The important part of the rod (as far as
induction is concerned) is still the same size. What is meant by the important partis the segment of the rod between the two
contact points. Making the rod longer simply adds additional length out side of the enclosed region of flux. You might be tempted to think that L in the relationship e = BLv has increased, but it is in fact the same. As a result, the power drain does not change. Taking the rod length into account was not necessary, assuming that the first three statements are interpreted
correctly. The best answer is choice D.
147
MINI-TEST EXPLANATIONS
Choice D is the best answer. Increasing the plate separation while keeping the voltage constant will change the magnitude of the electric field between the plates. Recall that voltage and electric field are related by: V = Ed, where d is the distance separating the plates. Changing the value of d will change E, if the voltage is kept constant. Changing the voltage across the
plates without changing d also changes E. The gel acts as a matrix to hold the DNA in place. Changing the gel viscosity
alters the rate of DNA migration, since the DNA experiences forces from interactions with the gel, as well as the electric
field. The best answer is choice D.
9.
Choice C is the best answer. This question can be answered by knowing definitions and does not require a complete understanding of the experiment. The current increases, which according to Ohm's law, V = IR, occurs with increasing V or decreasing R. Although increasing temperature generally increases resistance, this should not cause a current increase. In fact, for a constant voltage, the current should decrease with increasing resistance. Therefore, choice A is incorrect. The voltage across the plates is held constant by the power supply and remains unaffected by the temperature of the buffer, so choice B is incorrect. As temperature increases, we should expect the gel to begin to disintegrate or melt, not harden. If the gel did harden, this would increase resistance to ion migration, which results in a slower charge movement, and thus a reduced current. For that reason, choice D is also incorrect. Choice C must be the best answer by the process of elimination.
In a buffer, a weak acid can dissociate so that ions are released into the solution:
H|A] + H20
H30+ + |A]-
As the temperature increases, the reaction must be driven to the right (dissociation reactions are generally endothermic), so
more ions will be released. This will increase the current. The best answer is choice C.
10.
Choice D is the best answer. The experimenter sees nothing on the gel, because he placed it in the tank incorrectly! DNA is negatively charged. This means the gel should be placed in the tank so that the wells containing the DNA are near the negative electrode. That way, when the electric fields are turned on, the DNA will run from the negative electrode to the positive electrode. By loading the gel in the way indicated, the experimenter has inadvertently arranged for the DNA strands
to stay close to the (+) plates rather then migrate across the gel! The best answer is choice D.
11.
Choice A is the best answer. Smaller strands of DNA (size or mass of the strand is indicated by M) will migrate farther (distance is indicated by D). The graphs in choices A and C both express this relationship. Considering the relationship
between M and D more carefully, it is best shown by choice A (noting that we are plotting logM and not M on the vertical
axis). The best answer is choice A.
12.
Choice D is the best answer. As mentioned in the passage, DNA has an intrinsic negative charge, due to the presence of phosphate molecules. DNA polymers of different sizes should run as distinguishable bands, since DNA polymers of different sizes have different charges (the larger the DNA molecule, the more phosphates it has, so the larger the charge it has). However, as the molecules increase in size, they will be more affected by viscous drag forces. The viscous drag forces tend
to oppose the electrostatic forces. Consequently, DNA polymers of different sizes run as one indistinguishable band in a liquid. Choice A is incorrect, for the reasons just mentioned. Choice B is incorrect; diffusion should spread the DNA out, not clump it together. Choice C is also incorrect; the liquid gradient is there simply to keep the DNA from diffusing. Sucrose is
electrically neutral and therefore has no effect on the electric field. The best answer is choice D.
13.
Choice B is the best answer. From the passage, we are given the empirical relationship between migration distance D and molecular size M: D = a - b (logM), where a and b are constants that depend on the electrophoretic conditions. As M increases, D decreases. Therefore, smaller molecules migrate farther. Since the DNA strands are negatively charged molecules, they generally migrate from the top towards the bottom of the gel (as the passage states). Thus, the longest strands should be closest to the top of the gel. Strand VII is the longest and therefore the first in the list. Only choice Bbegins its list
with Strand VII, making it the best answer. The best answer is choice B.
14.
Choice A is the best answer. Electric fields are vectors. If the two fields are on at the same time, the net electric field is the superposition of the two individual fields. Electric field B has twice the magnitude of Electric field A, so the net field should
point in the direction of Electric field B. The best answer is choice A.
Electrostatics
Choice D is the best answer. Except in special cases, the actual charge carriers in conductors are electrons. Electrons have mass as well as charge, so the sphere that acquires the electrons will have slightly more mass, and the sphere that lost the
electrons will have slightly less mass. The best answer is choice D.
148
MINI-TEST EXPLANATIONS
16.
Choice A is the best answer. Charge is a conserved quantity, which means that it can be neither created nor destroyed. It canonly be transferred from one object to another. The process of charging a glass rod (an insulator) is poorly understood, butit is believed thatfriction between the silk and the rodstrips electrons from the glassand deposits them onto the silk. The silk has a higher affinity for electrons than does theglass. Thisleaves a deficit of charge on the glass rod. Thus, thecharge on
the rubbed glass rod and the silk have to be equal in amount, but opposite in sign. The best answer is choice A.
17.
Choice D is the best answer. When two objects carrying different charges come into contact with each other, the charge
densities will balance out between the objects through the transferof electrons. To prevent charge transfer, the objects should be separated from one another by an insulator, such as air. Preventing charged objects from touching each other prevents
charge transfer, making choice D the best answer. The best answer is choice D.
18.
Choice D is the best answer. The rubbed glass rod now has a net charge on it. Let the net charge of the rubbed glass rod be positive. A metal is a conductor, which means that charge is free to flow through it. When the rubbed glass rod is brought close to Sphere I, negative charge is attracted to the glass rod, and positive charge is repelled. The same is true for Sphere II. Negative charge will be attracted to the rubbed glass rod, while positive charge will be repelled. If the two spheres are then connected by a conducting wire, charge is free to flow from one sphere to another. The positive charge on Sphere I will flow to Sphere II, trying to get away from the glass rod. Negative charge will flow from Sphere II to Sphere I, to get closer to the glass rod. When the conducting wire is removed and the glass rod taken away, the metal spheres are each left with a net charge. Sphere I, the sphere closer to the glass rod, will have acquired a charge opposite to the charge on the glass rod. Sphere II, the sphere farther away from the glass rod, will have acquired a charge that is the same as the charge on the glass rod. This process of charging a conductor without actually touching it is called induction. The best answer is choice D.
Choice B is the best answer. Although there is a nearly inexhaustible supply of electrons in the metal rod, there are two
19.
competing effects going on. Suppose the rubbed glass rod has a net positive charge. The electrons are attracted to the rubbed end of the glass rod, so they flow to the end of the metal rod closer to the glass rod. However, electrons are also repelled by each other. Eventually, there are so many electrons at the end of the metal rod closer to the glass rod that the attractive force
experienced by the positive charge is balanced by the repulsive force from other electrons. At this point, the electrons will
cease to flow. Choice A is incorrect, for the reasons just mentioned. Choices C and D are incorrect: Electrons are the charges that move in conductors, not positive charges. The best answer is choice B.
20.
Choice D is the best answer. These electrostatic experiments depend on insulators being able to acquire a net charge and
hold it. The charging of an insulator occurs by friction-stripping electrons from atoms, thereby ionizing them. A humid day means a greater amount of water is in the air than on an arid day. Water is a better conductor than air, so in the presence of a better conductor, the ions are less likely to stay ionized. It is easier for them to recombine into a neutral atom, reducing the initial charge buildup on the rods. This is why you canmost aptly shock yourself or your neighbor on a dry, windy day. The
best answer is choice D.
21.
Choice B is the best answer. Choice D can be eliminated immediately, because neutrons do not respond to an electrostatic
force. The question is reduced to determining whether there isanattractive force, a repulsive force, or noforce atall. Let the rubbed glass rod have a net positive charge. Then the end of the metal rod closer to the glass rod would have a negative charge, and the end farther away from the glass rod would have a positive charge. The negative charge in the metal rod and the positive end of the glass rod exert an attractive force on each other. The positive charge in the metal rod and the positive endof the glass rod will exerta repulsive force on each other. Electrostatic forces are distance-dependent:
F -L
r2
Since the negative end of the metal rod is closer to the glass rod, the attractive force on the metal rod is slightly larger than the repulsive force. Thus, there is a netattractive force on the metal rod. The best answer is choiceB.
22. Choice C is the best answer. Because glass and hard rubberare able to exert forces (attractive in some cases and repulsive
inothers) after being rubbed with fur, we can conclude that rubbing with fur is responsible for charging the species. Charges
accrue when electrons are transferred, so it is reasonable to assume that fur is used to transfer electrons to the material that
rubs against it. Choice A is a valid statement and thus eliminated. A conducting rod by definition can transfer electrons, so
choice B is a valid statement, which eliminates it. Because the glass rods repel one another after being rubbed by silk, they
must be transferring electrons to the silk. Choice D is a valid statement and thus it's eliminated. The spheres do not create electrons; they simply hold the charge that isadded to them. Choice C is an invalid statement. The bestansweris choice C.
149
MINI-TEST EXPLANATIONS
Questions 23 - 25
23.
Choice B is the best answer. Conceptually, we know that if the plates are moved farther apart while the voltage is held constant, then the force acting on any particular drop will be reduced, because force depends on distance. This eliminates choices A and D. If the plate separation is doubled while the voltage across the plates is kept constant, then according to the relationship AV = EL, the electric field must be reduced by half. Since the electric force is given by: F = qE, cutting the
strength of the field in half will reduce the force at any point in the field by one-half. For any particular drop at any point between the two plates, the force will be reduced to half of its original value if the distance between the charged plates is
doubled. The best answer is choice B.
24.
Choice A is the best answer. A charged particle moving through a magnetic field will feel a force that is both perpendicular to the orientation of the B field and perpendicular to the direction of motion. The particle enters moving from the left to the right. The B field is oriented into the page, so the direction of the force must be either upward or downward. This results in either path I or path III being correct. Path II and deflection out of the page are not possible, so choices B and D are eliminated. According to the right hand rule, move your fingers in the direction of the motion, bend your fingers in the
direction of the field, and the direction of the force on a positive ion is in the direction of your thumb. This is upwards, so
the best trajectory is Path I. The best answer is choice A.
25.
Choice A is the best answer. This is similar to the previous question, but involves the right hand rule. If you think that there will be any motion of the wires at all, then cross out choice D. To be more specific, look at the magnetic field lines and how they interact with the wires. The magnetic field lines due to the current in wire #1 are drawn (wire #2 also has field lines, they just aren't drawn.) The magnetic field due to wire #\ points out of the page where wire #2 is. The resulting force on wire #2 is to the right using the right-hand rule. If you repeat the process for wire #1, you will find it feels a force towards
the left. Thus, the wires attract.
1
B out
i'B
into
o 0
#2 #1
111
on 2 by 1
150
MINI-TEST EXPLANATIONS
(1-5)
(6 -10)
(11 -17) (18 - 21)
III.
(22 - 26)
(27-32) (33 - 36) (37 - 41)
(42 - 48) (49 - 52)
VII.
MCAT Score
13-15 10-12 7-9 4-6
1-3
42-52
34-41 24-33 17-23 1-16
Passage 1 (Questions 1 - 5)
In 1906, Robert Millikan devised an experiment that allowed him to determine the charge of an electron. A schematicof Millikan'sset-up is shown in Figure 1 below:
2.
If the voltage across the plates were reversed, what would happen to the oil drops between the plates?
A. They would accelerate upward. B. They would accelerate downward. C. They would move with a constant velocity upward.
4B
Oil Can
=\
o o o
o
D. They
would
move
downward.
!jS
3.
Suppose there are two oil droplets between the plates. If the distance between the droplets is halved, what happens to the force between the droplets?
A. It doubles.
B. It is reduced by half.
^^\
^^
C. It is quadrupled.
D. It remains the same.
c
Figure 1
^^>
4.
form a capacitor. There is an electric field between the plates. The metal plates are inside an insulated cylindrical container made of clear glass. Oil drops are introduced into the container through a small hole in the top. The oil drops acquire a negative charge
as they pass through the nozzle of the oil can. Some of the
Suppose the original oil droplet were replaced with a positively charged one that had twice the charge and three timesthe massof the original droplet How would
drops fall through a hole in the upper plate. By adjusting the voltage between the plates, certain drops can be slowed down, and in some cases suspended between them. The relationship between the electric field between the plates and the voltage across the plates is:
AV = EL
5.
1.
In order for an oil drop of mass m, radius r, and charge density p, to be suspended between the plates, the
magnitude and direction of the electric field must be:
3m8 -; downward.
B.
4jtr3p ; downward.
3mg 3mg
; upward.
4jtr3 p
D.
; upward.
3mg
152
6.
A metal bar with mass M, length L, uniform density p, and resistance R is placed on parallel rails that slope up with
a gradually increasing tangent, as shown in Figure 1. The bar, represented by the segment from X to Y, has a higher conductivity than the rest of the apparatus. Points a and f
represent connections from the base of the rails to a box that can serve as either a power supply or an ammeter. The rails from point e to point f and point a to point b are made of a conducting metal. The support structure from points e and b to the base and the base itself are insulators. For simplicity, assume the rails have negligible electrical resistance and friction and that the resistance in the bar is negligible. Two experiments were conducted on this apparatus.
Experiment I
A. B. C. D.
No current is produced. Direct current is produced that travelsfrom X to Y. Directcurrent is produced that travelsfrom Y to X. Alternating Current is produced.
7.
A bar made of which of the following materials would NOT have worked in Experiment II?
A. Copper
B. Iron
C. Graphite
D. Calcium oxide
A uniform magnetic field of adjustable magnitude was oriented upward, perpendicular to the base of the apparatus. The adjustable bar was then placed at the top of the rails and released. The induced current through the bar was measured
as it fell. The current induced in the bar was due to a
8.
phenomenon known as Lenz's law. Whenever there is a change in magnetic flux through a loop, a current is induced in the loop which fights this change in magnetic flux. For Experiment I, the loop being studied is the cyclic path from f
-a-X-*Y f.
From a-b-c--*c-*e-+f
From c-*X-*Y-*d-c
From c-b-*a-f^e-*d
9.
In Experiment I, releasing the bar from a higher point on the rails will result in all of the following EXCEPT:
A. a greater induced current when the bar reaches the
bottom of the rails.
In the absence of any external magnetic field, a voltage was applied between points a and f to produce a current through the bar. The bar gradually climbed the rails until eventually coming to rest. It was assumed that the gravitational force on the bar was equal to the magnetic force generated by the current Different voltages were applied and the bar was suspended at various points along the rails. The voltage and resting height were recorded for each trial. In order to support the idea of Lenz's law, when the switch between points a and f was open, the bar slid down the rails unimpeded in Experiment I. In Experiment II, the bar did not move unless the voltage source was connected.
10.
In Experiment II, starting when the bar is suspended, what will be observed when the switch between points a and f is opened?
A. The current through the bar remains the same, so the bar remains stationary. B. The current through the bar goes to zero, and the
bar descends to the bottom of the rails.
153
temperature of the cathode remains the same. The kinetic energy of the ejected protons compared to the
kinetic energyof the ejected electrons would be:
Cathode
Electron beam
cathode. (To a good approximation, this thermionic emission of electrons can be predicted, if we treat the electrons like the molecules of an ideal gas.) The ejected electrons are then accelerated by a high voltage applied to the anode. The electrons pass out of theanode through a small holeandenter a region of electric and magnetic fields. The electric field is produced by two parallel charged plates, whereas the magnetic field is produced by charge carrying coils near the plates. These two fields exert forces on the electron.
The electric force is given by: F= qE, where E is the electricfield, and the magnetic force is given by: F = qvBi, where v is the velocity of the electrons after leaving the anode, and Bi is the component of the magnetic field perpendicular to the electron velocity.
The electric and magnetic fields are set up so that the forces on the electrons will point in opposite directions. The
horizontal and vertical deflections of the electrons are
C.
14.
controlled by adjusting these two fields. (Some CRTs use two sets of parallel plates-one set to control horizontal
deflection and one set to control vertical deflection.)
A. generate their own magnetic field, and this must be taken into account when selecting the magnetic field between the plates. B. generate their own magnetic field, but this does not
have to be taken into account
C. do not generate their own magnetic field. D. generate an electric field, and this must be taken into account when choosing an electric field between the plates.
point where it is struck by an electron, producing a tiny visible spot Adjusting the voltage across the parallel plates or adjusting the magnetic field allows the point to be placed
anywhere on the tube.
15.
If an electron is observed to travel through a certain region of space undeflected, what can be concluded? A. There is definitely no electric field in that region,
plates undeflected. If the electrons enter the region between the plates with the same direction, but with an
excessive velocity:
but perhaps there is a perpendicular magneticfield. B. There is definitely no magnetic field in that region, but perhaps there is an electric field.
C. No field of any kind is present. D. Both an electric and magnetic field may be present parallel to one another.
A. B. C. D.
they will be deflected upward. they will be deflected downward. they will remain undeflected. they will be turned back the way they came.
154
16. When the beam of electrons strikes the target they are
brought to a sudden stop, generating X-rays. The
wavelengths of these rays depend on the:
I.
II. III.
A. B. C.
II only
E H H V if V ^f^V^
III
Path I
Path II Path III
A. A moving electron
B. An orbiting proton
C. A fixed anion
D. An accelerating cation
20.
Which of the following are needed to calculate the force a magnetic field exerts on a moving electron?
I. The electron charge
II. The electron mass
21. If an electron, proton, and neutron are moved through the same potential difference, what is true regarding the
magnitudes of their potential energy changes?
A. B. C. D.
APEeiectron > APEproton > APEneutron APEproton > APEeiectron > APEneutron APEeiectron = APEproton > APEneutron APEeiectron > APEproton - APEneutron
155
24. Which procedure would most easily send a negative ion through thefullyoperational velocity selector?
A. Reverse the direction of E only.
two parallel plates. These plates, having different voltages, maintain a steady, uniform electric field between them. There
is alsoa static magnet in the velocity selectorthat generates a
25. For a selected ion passing through the velocity selector undeflected, how does its speed, v, relate to E, B, and q?
The theory behind the velocity selector was formulated by Lorentz, who specified the net force on a charged particle that moves through an electric and magnetic field:
F = qE + qvBi,
Equation 1
A. v =
B
B. v = B
E
C. v=
B
where E is the electric field strength, Biis the magnetic field strength perpendicular to the charge velocity v, and q is the magnitude of charge.
22. What is TRUE for an undeflected particle in a velocity
selector?
D. v = <E
I. The work done on the particle is non-zero. II. The effects of electric fields and magnetic fields can treated as independent of one another. HI. The particle could be neutrally charged.
A. II only B. I and II only C. I and III only
D. II and III only
26.
A. force and acceleration depend upon its mass. B. force depends upon its mass, but acceleration does
not
23.
A magnetic field pointing into the page (each field line is represented by an V) will deflect upward all of the following particles, EXCEPT a:
XXX XXX
XXX
XXX
XXX
A. B. C. D.
proton moving from the left to the right. fluoride ion moving from the right to the left. sodium ion moving from the left to the right. titanium ion moving from the right to the left.
156
Passage V (Questions 27 - 32) In an experiment designed to study Faraday's Law, a student observed the induced current generated upon migrating three separate loops at uniform speed through a
uniform perpendicular magnetic field. The field was created by placing a cylindrical magnet directly above a second cylindrical magnet, such that the loop could be moved through the field between the poles, as shown in Figure 1.
Which graph accurately reflects the current associated with Loop E in the experiment?
A. <
g 0fc
3
^^
I A Time (s)
B. <
r\
3
r \ Time (s)
Figure 1 Magnetic field used in the Experiment In Experiment I, the student pushed through three separate copper loops of varying dimensions all in a way that the area within the loop was parallel with the surface of the magnets. The three loops have the following dimensions.
c. <
Time (s)
3
D. <
Time (s)
3
Loop C: rectangular with edges of6cm and 8cm. A=48 cm2 Loop D: square with edges of7cm. A=49cm2 Loop E: circular with a radius of4cm. A=50 cm2
30.
What is true for Loop C in Experiment I? A. It experiences the same emf whether it enters the B
field with the 6cm side first or the 8cm side first
The student pushed the loops through at constant velocity, despite the increase in opposing force as the loop entered and exited the field. Each loop was attached to a galvanometer, used to measure the induced electromotive force, e. The emf can be calculated using Equation 1:
e = - d(BA cos $)/dl Equation 1
B.
where e represents the emf, B is the strength of the external field, A is the area in side the loop, and <j) is the angle between the field vectors and the vector perpendicular to the surface of the area within the loop.
31.
Which change will NOT increase the magnitude of the current induced into a loop entering a B field?
In Experiment II, the student repeated the steps of Experiment I, but used loops made of tin wire instead of
copper.
27.
A. B. C. D.
32.
Increasing the area inside of the loop Moving the loop into the field at a faster rate Moving the two magnets closer to one another Using a loop made from a thinner wire
B.
If Loop C is moved from the right side of the magnetic field in Figure 1, through the field and then on to the left side, what type of current does it feel upon exiting the field while moving to the left?
A. A clockwise alternating current B. A counterclockwise alternating current
C. D. A clockwise direct current A counterclockwise direct current
157
36. Which of the following graphs BEST represents the relationship between the magnetic field strength and the area of the coil in a system where e0 = BAoo, if the maximum voltage and coil rotation frequency are held
fixed?
33.
pathway of a negatively charged particle moving leftto right through a magnetic field pointing into thepage?
A. B.
A.
B.
C.
D.
D.
34.
t
wire I wire II
C.
35.
When a charged particle is added to the following electric field, it will accelerate. Which particle will experience the greatest average magnitude of acceleration when added to the field at point A?
A. B. C. D.
A negatively charged particle with low mass A positively charged particle with low mass A negatively charged particle with high mass A positively charged particle with high mass
158
38. All of the following changes will lessen the displacement between the point where particles enter Region 2 and the point where particles collide with the
detector plate EXCEPT:
Region 2
X X X X
39. The double filter between Regions 1 and 2 ensures that: A. a uniform ion beam, perpendicular to the plates of
the filter, is formed.
velocity is formed.
C. the beam consists of only cations. D. the beam consists of only singly ionized particles.
XXX
XXX
XXX
Doubling both the magnetic field in the velocity selector and in the deflecting zone of a mass
spectrometer would have what affect on the radius in
The speed of the particle may be controlled by a velocity selector, which is comprised of a magnetic field and electric field, both of which are perpendicular to the motion of the
A. The radius would decrease by a factor of 4. B. The radius would decrease by a factor of 2.
particle. The two fields are aligned so that the forces oppose one another. The particle will continue in a straight path only if qE = qvB. This means that the particles that pass into the deflecting region of a mass spectrometer have a velocity of E/B. The mass spectrometer in Figure 1 does not have a
velocity selector. Once in Region 2, the radius of the arc can
be used to determine the mass to charge ratio of the particle. The radius of the arc in Region 2 equates to the mass, charge, magnetic field, and velocity according to Equation 1.
r_mv
41.
To accelerate anion particles from left to right in Region 1, and deflect those particles out of the page in Region 2, how must the E and B fields be aligned in
Figure 1?
Bq
Equation 1
37. Assuming that the particles enter Region 2 with the same velocity, which of the following cationic particles
will have the GREATEST radius of curvature, r, in Region 2?
A.
A. B. C. D.
Anode plate left, cathode plate right, B field up Anode plate left, cathode plate right, B field down Anode plate right, cathode plate left, B field up Anode plate right, cathode plate left, B field down
40Ca2+
7Li+
B.
C. D.
24Mg2+
23N
159
Passage VII (Questions 42 - 48) The cyclotron (Figure 1) is a device used by physicists to accelerate ions to high speeds and high kinetic energies. The cyclotron consists of two semicircular regions Si and S2 of
the same radius R with a small gap d between them. S\ and
44.
What is the kinetic energy of an ion of mass m and charge q as it is ejected from the cyclotron?
A. B.
qB
2Rm
IqBR
2
C.
qBR
2m
Ionized particles
enter here
D.
cfBV
2m
45.
Gap(d)(
Which of the following statements would NOT be true, if the voltage amplitude across the gap were doubled? A. An ion would spiral out in less time and be ejected
sooner.
Ionized particles
leave here
C. The cyclotron frequency would remain unchanged. D. The magnetic field would remain unchanged.
Figure 1
Ions are injected near the center of the cyclotron. They are accelerated across the gap by an electric field until they enter the magnetic field region. Once there, they move in a circular path due to a uniform magnetic field which points into the page. As the ions circulate, they are sped up by the electric field that exists in the gap. As an ion increases its
46.
In comparing the work done on an ion by the electric field and the magnetic field in a cyclotron, we find that: A. the electric field does more work than the magnetic
field.
D. the neither the electric field nor the magnetic field does any work.
f- qb
2 31 m
47.
How do the cyclotron frequencies for singly ionized H2 (m = 2) and singly ionized He (m = 4) compare?
A. B.
H2
42.
C.
D.
A. B. C. D.
43.
48.
If the cyclotron frequency is 10 MHz, how long will it take an ion to complete 200 orbits?
A. B. C. D. 0.2 ^s 2/iS 20 ps 200 ps
160
D.
zero.
52. When a velocity selector is fully operational, it allows only an ion with a specific velocity to pass through the
plates undeflected. Which orientation of electric and
49. Which of the following changes does NOT decrease the work required to move a negatively charged particle against an electrostatic force, from a positively charged plate to a negatively charged one?
I. Increasing the battery voltage
II. Decreasing the particle charge
III. Increasing the particle mass
magnetic fields would allow a positive ion to pass undeflected when traveling from left to right? (Note: The electric field points either up or down in the
pictures. The magnetic field points either into "x" or out of "" the page.)
A.
yr .
\ r
\ f .
\ f.
y
'
B.
X I IX i
X
IX
X X
X X
X
X
X
X
X
50.
C.
X X
X X
X X
y rx y rx y f x
'X
B. A magnetic force is perpendicular to its field, while an electric force is aligned with its field. C. A moving particle can only be turned by a magnetic force and not by an electric force. D. A charged particle can experience zero magnetic force in the middle of a uniform magnetic field, while a charged particle in the middle of a uniform electric field will experience an electric force.
D.
51.
What is NOT true when moving a positively charged particle in the following electric field?
2.
3. C 9. C
15. C
21.
4. D 10. B
16.
22.
5. B
11. B 17. D 23. D
6.
12.
B
D
B. Point b is at a higher potential than Point c. C. Natural flow for the particle is from Point b to
Point c.
8. A
14. 20. B
B
C
D
18.
24.
C
D
26.
32.
C C
C
D
28.
29. A 35. A
41. D
30.
31. D
37. D
34. A
36. A
42.
38.
44.
40. A 46. A
52. C
C
D
43. C
47. C
48.
49. C
50.
161
Choice A is the best answer. We must consider both magnitude and direction. First, let's consider magnitude. Thinking
about the basic relationship between the required electric field and the mass of the drop, we see that they should be directly
proportional to each other. That is, if the drop is more massive, a stronger electric field is required. This rules outchoices B
and D. To decide direction, remember that gravity points downwards, which requires the electric force to point upwards.
Since the charges being supported are electrons, and since electrons are always forced in the direction opposite that of the
electric field, the electric field must point down. You must keep in mind that convention for electric fields is to draw them according to the way a positive chargewould naturally flow. The best answer is choice A.
2. Choice B is the best answer. In order for the drops to be suspended, the electric force must point upward to oppose the
gravitational force downward. By reversing the voltage, the direction of the electric fieldand therefore the direction of the
electric force-would also be reversed. Now the electric force and the gravitational force act in the same direction (downward), so the droplets will be accelerated downward, and with a magnitude of acceleration greater than g. The best
answer is choice B.
3.
Choice C is the best answer. This question is asking us to consider the force between two charged particles. The coulomb force between two charged particles is:
F = k^1
r2
This force is inversely proportional to r2. If the distance r separating the two charges is reduced by one-half, then the force
between the charges is quadrupled. The best answer is choice C. 4. Choice D is the best answer. The question asks about the magnitude of the forces, so we can ignore that the negatively charged oil droplet has been replaced by a positively charged species. We simply need to consider the magnitudes of the electric force and the gravitational force. We know that qE = mg, and that:
E = ^
q
in order for the oil drop to remain suspended. If m increases by a factor of 3 and q increases by a factor of 2, then the new
electric field would be:
2q 2 where E' is the new electric field, and E is the original electric field. At the very least on this question, you could have eliminated choices B and C, as they are the exact same answer, just worded differently. The best answer is choice D.
E = ^Hi = 3^
5.
Choice B is the best answer. Oil floats on water, telling us that oil is less dense than water. We can rule out choice A. Oil pours more slowly than water, which you know from personal experience, so oil is more viscous than water. This eliminates choice C. In the passage, vve read that Millikan chose oil because it has a relatively low vapor pressure (i.e., it does not evaporate quickly), and because oil drops can hold charge well. Although we know nothing about choice D, because the
passage addressed oil's ability to hold charges, choice B is the most likely answer the test-writer wanted you to pick. The
best answer is choice B.
Lenz's Law
Choice B is the best answer. In Experiment I, the external magnetic field points vertically upward, so the direction of induced current can be obtained using the right hand rule. Before considering that, we should consider which choices can be eliminated without knowing the direction of the current. The bar slides down the rails, so there will be a current. This eliminates choice A. Because the bar slides down the entire time, the current will remain in the same direction, making it direct current. This eliminates choice D. When the bar slides down the rails, the magnetic flux through the loop created by the rails and the bar decreases, because the area inside of the loop decreases. Lenz's law states that a current will be induced in this loop to fight the change in flux, so current will definitely be induced. Now we need to determine the direction of the current. If you point your thumb in the direction the bar is sliding (angular and down) and put your index finger in the direction of the magnetic field (up), then your middle finger points from X to Y, so that is the direction of current. Since
choice B is a direct current going from X to Y, it is the best answer. The best answer is choice B.
162
7.
Choice Dis the best answer. Any material which conducts electricity would work in Experiment II. Since copper and iron are pure metals, they both conduct electricity. This eliminates choices Aand B. Neither graphite nor calcium oxide are pure metals, so we cannot automatically say that either of them conduct Although graphite is a nonmetal, it has a crystalline structure that allows for its electrons in the Jt-level to have some freedom to move, so it actually conducts. Taking this into
consideration, one should see that the only substance that would not haveworked in Experiment II is calcium oxide, because it doesn'tconduct electricity. Salts, such as oxides, do notconduct electricity unless they are dissociated in water. The best
answer is choice D.
Choice A is the best answer. The current can only flow through a region where it conducts electricity. It is stated in the
passage that thesegment from pointe to pointb is for support and is made of an insulating material. This means thatcurrent
cannot pass through points b, c, d, and e. This eliminates all of the choices except for choice A. If you spent time trying to determine the direction (whether it was a-to-X-to-Y-to-f-to-a or a-to-f-to-Y-to-X-to-a), you wasted time. Occasionally a
question may look complicated but it is in fact simple to find the best answer. The best answer is choice A.
Choice C is the best answer. In Experiment I, if the bar was released from a higher point on the rails, it would definitely
have more kinetic energy upon reaching the bottom. In addition, there would be a larger induced current and thus induced
magnetic field due to the fact that there was a greater change in flux through the loop than if the bar had been let go from a lesser height. On the other hand, since there is no relationship between the external magnetic field and the height of the bar,
it would be unchanged. The best answer is choice C.
10.
Choice B is the best answer. In Experiment II, before the switch between a and f is opened, there is current flowing between points a and f that is in the oppositedirection of the currentbetween points X and Y. Once the switch is opened,the
current stops and there is no longer a force suspending the bar. Without any force holding the bar up, it will slide down the
rails due to gravity, eventually reaching the bottom. The best answer is choice B.
Passage III
(Questions 11 - 17)
11.
Choice B is the best answer. If the undeflected electrons have an increased magnitude of velocity compared to what they
had when they passed through in a straight line, then the magnetic force is greater than the electric force. The electrons will be deflected in the direction of the magnetic force, so they will be deflected downward. Just as motion is necessary to generate a magnetic field but not an electric field, the magnetic force is affected by velocity, while the electric force is not.
The best answer is choice B.
12.
Choice D is the best answer. According to the ideal gas law, the kinetic energy of particles is related to temperatureby:
KE = 2-kT
2
where k is the Boltzmann's constant. This says that the kinetic energy of a particle depends only on its temperature, and not on its mass or charge. Thus, the kinetic energy of the protons is the same as the kinetic energy of the electrons. The best
answer is choice D.
13.
Choice D is the best answer. This question helps to reiterate the point that MCAT questions require you to choose the best answer and not necessarily the correct answer. Protons and electrons have opposite charges. This means that if electrons move downward in the electric field, protons would move upward. If electrons move upward in the magnetic field, protons would move downward. Thus, the field directions still oppose each another and therefore would not have to be changed. In order for the protons to travel through the plates undeflected, the electric and magnetic forces must still be equal in
magnitude:
qE = qvB or E = vB
This relationship does not depend on the mass or the charge of the particle involved, only on the speed of the particles. Provided we do not change the speed of the protons compared to the speed of the electrons, we do not even need to change the magnitudes of the fields. We could reverse the direction of both fields (choice C), but it is not necessary, which makes
choice D a better answer than choice C. The best answer is choice D.
14.
Choice B is the best answer. Electrons in motion definitely generate a magnetic field, so choice C is eliminated immediately. The electric field they generate does not affect itself, so choice D is eliminated. Although an electron is a moving charged particle (which produces a magnetic field), a charged particle never responds to its own fields, electric or magnetic. The magnetic field it generates interacts with the external magnetic field, thereby causing a force that can be analyzed using the right-hand rule, but that is not a response to its own magnetic field. The best answer is choice B.
163 REVIEW EXAM EXPLANATIONS
15.
Choice C is the best answer.The electron is undeflected, which can be explained by the absence of a netforce acting on the electron. This is the case if (a) the electric and magnetic forces are of equal magnitude but opposite direction or (b) there are no electric and magnetic forces acting on the electron. Because there could be both an electric field and magnetic field, as
opposed to just one or the other, choices A and B are eliminated. In order to produce a force on a moving electron, the
magnetic field must be aligned perpendicular to the velocity of the particle, resulting in a force that ismutually perpendicular to both the magnetic field and the velocity. If the electron moves in the same direction as the magnetic field, it will feel no magnetic force. This means that the force exerted by the magnetic field is perpendicular to the magnetic field itself; so if the magnetic and electric fields are parallel, then the magnetic force is perpendicular to the electric force. This would not allow
the forces to cancel, so the electron would be deflected as it traveled. Choice D is not possible. The best answer is that there is no field of any kind present. The best answer is choice C.
16. Choice C is the best answer. X-rays can be produced one of two ways. When the electrons are brought to a sudden stop,
they lose all of their kinetic energy. Conservation of energy says this energy must go somewhere, and where it goes is into the production of x-rays. In addition, some of the electrons that strike the target may interact with the atoms of the target, by knocking electrons out of their inner-shell orbits. That leaves an unfilled space in an inner-shell orbit, which is filled by an
outer-shell electron making a transition. This process releases energy in the form of x-rays called characteristic x-rays, since their wavelengths depend on the electron transitions made, and these depend on the atoms involved. This means that the wavelength (and thus energy) of the x-rays depend on the accelerating potential of the electrons (which affects the electron's speed) and on the target material (and their electronic energy levels). Options I and II are valid. The speed of the x-rays depends on the medium and has nothing to do with the wavelength. Option III is invalid, confirming that choice C is the best
answer. The best answer is choice C.
17.
Choice D is the best answer. X-rays are electromagnetic radiation, and as such they have no charge. They will not
experience any force from either the electric or magnetic fields as they pass through them. Any change in the surrounding
fields would have no impact on the propagation axis of an x-ray. The best answer is choice D.
Questions 18-21
18.
Choice C is the best answer. An electric field affects a charged particle by accelerating it in the direction of the field, if the particle is positively charged. Remember that all definitions in physics are based on positive charge. The particle is accelerated (deflected) by the electric field in the downward direction, with a force of F = qE. The path that shows constant velocity in the lateral direction coupled with acceleration in the downward direction is Path III. The best answer is choice C.
19.
Choice C is the best answer. Any moving charged particle will be deflected by a magnetic field as long as the motion is not directly in line with the field. Considering direction is not mentioned in the question, the key feature is motion. Choice C, a fixed (i.e., not moving) particle will not be deflected by a magnetic field. The best answer is choice C. Choice B is the best answer. For this question we need to apply Paring the List or Multiple Concepts. First, consider an item that is easiest for you to grasp. If you know that electron charge is relevant, then Statement I is true and choice C is not; cross choice C out. Since Statement IV is in all remaining choices, there no need to consider it. Since mass usually only shows up in a gravitational force, Statement II must not be relevant. This rules out choices A and D, leaving only choice B.
The best answer is choice B.
20.
21.
Choice C is the best answer. To solve this question, pick two particles whose energy relationship you know, and use this information to rule out incorrect choices. For example, if you know neutrons experience no change in energy when moving through a potential difference, then choice D is incorrect. The remaining choices ask you to compare the energy change for an electron and proton. Since APE = qV and the two particles have the same magnitude of charge, they must have the same potential energy change. The best answer is choice C.
Velocity Selector
Choice D is the best answer. Work is defined as force x distance, or by the equation W = Fid. A selected ion is not forced (deflected) in any direction, so there is no force along the direction in which it travels (Ft = 0). The net work done on the
undeflected particle is 0. This makes statement I invalid. The whole concept behind the velocity selector is that the effects of the magnetic and electric fields are independent of each other (as shown in Equation 1), so the two fields can be set to oppose (and algebraically cancel) one another. Statement II is valid, as the remaining choices (A and D) state. If a neutral charge were to enter the velocity selector, it would pass undeflected. Remember, both electric and magnetic forces require a net charge on the forced particle. This validates Statement III. The best answer is choice D.
164
23.
Choice D is the best answer. A charged particle moving through a perpendicular magnetic field is subjected to a force that is both perpendicular to the orientation of the Bfield and perpendicular to the direction of motion. If a positive particle enters the magnetic field moving from the left to the right, and the Bfield is into the page, the direction of the force is upward. You can confirm this by using the right-hand rule. According to the right-hand rule, if you move your fingers in the direction of
the motion and bend your fingers in the direction of the field, the direction of the force on a positive ion will be in the direction of your thumb. Both a proton and sodium cation are positively charged, so choices A and C are valid statements and must be eliminated. A negatively charged ion, such as fluoride, would experience a force in the opposite direction. That
means that an anion must be moving right to left to experience an upward force in the field as shown. This makes choice B
valid, so it is eliminated. It is for choice D that the force will be downward. Titanium, ending in "-ium," is a cationic species
that will deflect downward when traveling from right to left. The best answer is choice D.
24.
Choice D is the best answer. Recall that the forces (and fields) are defined for positive charges. A negative charge will be deflected in the direction opposite that of a positive charge by both a magnetic and electric field. For the velocity selector to work, the forces must oppose one another. The original design (for the positive ion) has the fields generating opposing forces. If the particle is negative, the directions of the forces generated by the fields are reversed, but they will still be opposed. Eliminate choices A and B. Changing only one field would create a scenario where the forces sum together rather than cancel each other out. The best answer is either changing both fields or changing nothing. While a sound argument can be made for the validity of choice C, it is not the easiest route to the solution. Choice D is a better option, in that it is better to
do nothing than a double-reverse. This may seem like quibbling, but the MCAT does require that you choose the best answer, not the one and only correct answer. There is a big difference between the best answer and an absolutely correct
answer. The best answer is choice D.
25.
Choice A is the best answer. Paragraph 1 of the passage states that mass and charge are not involved in the deflection (or net force), so it must be true that velocity will not vary with the mass or charge. Choices C and D are unlikely to be the best answer. The manipulation of Equation 1 to describe a situation where the electric and magnetic forces are opposed gives us:
F = qvB-qE
Therefore, if F = 0, then qvB = qE. Canceling out the q from the equation yields: vB = E, which tells us that the speed of the particle can be found using: v = E/B. The best answer is choice A. 26. Choice C is the best answer. Equation 1 does not contain mass, so the net force does not depend on the mass. This eliminates choices A and B. Because force is mass times acceleration, the acceleration equals the force divided by the mass; therefore, acceleration depends on the mass. The best answer is choice C.
Faraday's Law
Choice D is the best answer. The electromotive force results from the induction of charge movement caused by the change in the magnetic flux. This is independent of the material of which the wire loop is made. The materials have different electrical resistances which impacts the current, but that has no impact on the emf. The best answer is choice D.
Choice D is the best answer. As a conducting loop first enters a magnetic field, it experiences a change in the magnetic flux (the magnetic field within the loop). This induces a current in the loop, making choice D the best answer. By generating current, the energy of the moving loop is being converted into current, so energy is drained as it enters the field. As such, it feels a repulsive force as it enters the field, not an attractive force pulling it into the field. Choice A is eliminated. A torque can be felt if the loop had an existing magnetic field (which would be possible if a current were being pushed through it by an external emf source.) That is not the case here, so a torque causing it to rotate 90 is not viable. Choice B is eliminated. Because of the resistance the loop feels upon entering the field, it actually slows down as it enters the field. This eliminates
choice C. The best answer is choice D.
28.
29.
Choice A is the best answer. As in all cases, as the loop enters the field, the magnetic flux is increasing and as the loop exits the field, the flux is decreasing. This means that the current moves in opposite directions when the loop is entering versus when the loop is exiting the magnetic field. This eliminates choices B and D. To answer the question from this point, we must determine whether the current is constant or varies as the loop enters and exits the field. In the case of Loop E, the loop is circular. Unlike with a rectangular loop, the area of the loop entering the field (and thus the magnitude of the magnetic flux) changes as the loop enters the field. As the circular loops enters the field, the magnetic flux increases at an increasing rate until the loop is half way in, after which the magnetic flux increases at a decreasing rate. This is best described in the graph in choice A. Even if that doesn't seem completely clear, choice C cannot be correct, because the magnetic flux does not increase at a uniform rate, so current cannot flow at a constant rate during the induction periods. The
best answer is choice A.
165
30.
Choice C is the best answer. Loop C is rectangular, so it has two possible orientations for entering the field such that the
plane ofthe loop is perpendicular to the magnetic field. The greatest emf is felt with the greatest change in flux. When the
rectangular loop enters long side (8 cm side) first, it experiences a larger change in flux than when it enters short side (6 cm side) first, assuming it enters with the same velocity in each case. This is simply due to the fact it is wider. This eliminates
choices A and B and leaves choice C as the likely best answer. It feels an emfno matter which side enters first, so choice D
is eliminated. The best answer is choice C.
31.
Choice D is the best answer. The magnitude of the current induced into the loop depends on the rate at which the magnetic flux changes. The greater the rate at which the magnetic flux changes, the greater the induced current. Increasing the area inside of the loop increases the magnetic flux as it enters a magnetic field, so choice A is eliminated. Moving the loop into
the field at a faster rate will increase the rate at which the magnetic flux increases, so the current is greater and thus choice B
is eliminated. If the two magnets are moved closer to one another, the magnitude of the external B field will increase, resulting in a greater magnetic flux within the loop. This will increase the current, which eliminates choices C. Using a loop of thinner wire causes a greater resistance. Although the magnetic flux does not change, and therefore the induced emf does not change, the current is reduced. The best answer is choice D.
32. Choice C is the best answer. If Loop C is exiting the field moving to the left, the magnetic flux is decreasing the entire time
the loop is leaving the field, so the current will travel in the same direction during the entire time it is exiting the field. This
means the current is a direct current, which eliminates choices A and B. Those two choices should have been eliminated
based on the idea that alternating current goes both directions, so it cannot be assigned a clockwise or clockwise orientation. To determine the direction of the current, we can address the question in one of two ways. The first way is to apply Lenz's law. Lenz's law states that as the magnetic flux within a loop changes, a current will be induced in the loop that opposes the change in the magnetic flux. In this case, the external magnetic field points down, so upon exiting the region inside of the loops experiences a reduction in the magnitude of the magnetic field pointing down. As such, the current induced in the loop will compensate for the loss by creating a magnetic field pointing down in the region within the loop. This is done by creating a clockwise current in the loop. Choice C is the best answer. This can be verified using the right-hand rule. As the loop leaves the magnetic field, only the back edge of the loop is completely immersed in the field. Considering motion of the conducting rod to be to the left and the orientation of the magnetic field to be into the page, the force on positively charged particles in the back edge of the loop will be downward (according to the right hand rule). That push will cause the positive charges to flow in a cyclic fashion, down the back edge, to the left in the lower edge, up the front edge, and to the right in the top edge. This describes a clockwise current in the loop, so choice C is verified as the best answer. The best answer is
choice C.
Questions 33 - 36
33.
Choice D is the best answer. The right hand rule describes the pathway of a cationic particle moving through a magnetic field. In Figure 1, the pathway of a cationic particle through a magnetic field into the page (represented by an x) is shown. An anion will show the same shape pathway as a cation, but with deflection in the opposite direction. This is best represented by choice D. Choice C is too drastic (and non-circular) to be an observed pathway. The best answer is choice D.
34.
Choice A is the best answer. Wires with currents moving in the same direction attract, while wires carrying opposite
currents repel. Because we are only considering a direct current in each wire, there will be a force that maintains the same direction. This rules out choices C and D. This phenomenon is caused by the magnetic force on each wire due to the B field caused by the current in the parallel wire. Looking at wire 1, it creates a B field into the page at the point of wire 2. Using F = U co B and the right hand rule, the force on wire 2 due to wire 1 is found to be to the right. Similarly, the force on wire 1 due to wire 2 is found to be to the left. Thus parallel wires carrying currents in opposite directions repel one another
I
Bout
6!
ft a B,
on 1 by 2
Bout
i R
Dinto
0 O 0
0 o
0
0 0
O0
on 2 by 1
0
#2 #1
0
//l
n n
166
35.
Choice A is the best answer. First off, you need to consider that the force exerted on the particle depends on the magnitude
of the charge and the strength of the field. Assuming that the magnitude of the charge is the same in all of the choices, we
need to consider the field's strength. The lines separate on the right side, so the field is stronger on the leftside than the right side. As a particle moves left to right, the strength of the electric force is diminishing. Conversely, as a particle moves right to left, the strength of the electric force is increasing. Field lines are drawn the way a positive charge would migrate, so
positive charges would experience a decreasing force over time. On the other hand, negative charges would feel an increase in field strength, so negative charges will feel a greater average acceleration over the migration. Choices B and D are eliminated. To decide between choices A and C, we need to consider F = ma. For a given force, as mass increases, the acceleration of the particle will decrease. To generate the greatest acceleration, we need the lightest particle. The best answer
is the light, negative particle. The best answer is choice A.
36.
Choice A is the best answer. This may very well be an extremely intimidating topic, in which case many of us let panic influence our thought process. Even though we may have little understanding of the subject matter, sometimes a question is actually asking us to demonstrate our analysis skills and not our knowledge. The relevant equation is given in the question
as:
e0= BAco
The equation states that the magnetic field, B, is inversely proportional to cross-sectional area of the loop, A. That is, as A increases, B must decrease, which eliminates choices C and D. This particular plot is choice A, an asymptotic relationship. Many people incorrectly think choice B is the graph of an inversely proportional relationship, but it is not. Choice B is a linear relationship, with a negative slope. The best answer is choice A.
Mass Spectrometer
Choice D is the best answer. The biggest arc results from the particle with greatest mass-to-charge ratio, assuming all of the particles have the same velocity and the magnetic field magnitude is equal in each trial. This is because as mass increases, the radius of curvature increases and as the charge decreases, the radius of curvature increases. The greatest mass-
39.
40.
41.
167
Cyclotron
Choice C isthebest answer. How many orbits are required for an ion to gain a total kinetic energy of6 x lO"1^ J, ifitgains 1x 10-1^ J every time it crosses the gap? The ion crosses the gap twice per orbit, so itgains 2 x 10_1^J with every orbit. The
number of orbits is given by:
Number =
or
N =
6x 10'14J
2(1 x 10"16 j)
43.
Choice C is the best answer. If the cyclotron frequency is 10 MHz, how long will it take an ion to complete 200 orbits? According to the passage, the cyclotronfrequency is the frequency at which an ion circles. To calculate the time required for
1 orbit (the period of orbit), we use:
= 1 x 10-7 s f 10 x 106 Hz The period is the time to complete one orbit, so we must multiply T by 200 to determine the time required to complete 200
T = I =
orbits. 1x lO'7 x200 = 200 x 10"7 =20 x 10"6 = 20/<m. The best answer ischoice C.
44. Choice D is the best answer. What is the kinetic energy of an ion of mass m and charge q that is emitted from the cyclotron? According to the passage, an ion is emitted when the radius of its orbit is equal to the radius of the cyclotron, R.
The definition of kinetic energy is:
KE = Imv2
2
v=aM
m
2m
Choice B is the best answer. Which statement would be false, if the amplitude of the voltage in the gap were doubled? A good way to answer this question is to eliminate the true answers, starting with theeasier ones to eliminate. Choice C is true, because the cyclotron frequency, as given in the passage, does not depend upon the gap voltage. Choice D is true, because
the magnetic field is generated by a device other than the voltage source and is therefore independent of the gap voltage. Regarding choice A, the ion would spiral out sooner, because each time the ion crosses the gap, it gains kinetic energy. A doubled voltage amplitude means that it would gain twice the energy per gap-crossing that it gains under normal voltage conditions. That is, the ion would reach its emission speed sooner. Choice B is false, because the kinetic energy upon emission is related to the cyclotron frequency, which does not change here. Why does this matter? Well, the frequency tells us how many times the ion circles the cyclotron per second. This dictates its speed, and hence its kinetic energy, upon
emission. Since thefrequency does notchange, neither should the kinetic energy. Another way to think about this is that the exit point is at a fixed distance from the center, so the particle must reach an exact speed to attain the exit radius, which
means it reaches an exact kinetic energy to attain the exit radius. The best answer is choice B.
46.
Choice A is the bestanswer. How does the work done by the electric field and the magnetic field compare for an ion in a cyclotron? Choice C says the electric field and magnetic field dothe same amount of work, and choice D says they both do
no work. If choice D is correct, then choice C must also be correct, which means neither can be correct. The best answer is
that the electric field does more work. It does work when it speeds up the ion while the ion is in the gap. The magnetic field actually does no work on an ion, because the magnetic force is always perpendicular to the direction of travel (given by the right-hand rule). When a force is perpendicular to the path, it can do no work. This is why the particle traverses a semicircle at constant speed in a perpendicular magnetic field, gaining no speed and therefore gaining no energy. The best answer is
choice A.
168
47.
Choice C is the best answer. How do the cyclotron frequencies for singly ionized H2 and singly ionized He compare?
2nm H2
2jtmHe
They both have the same charge, but He has twice the mass of H2. l*H2 = 2fHc
2m
48.
Choice D is the best answer. The questions asks for the cyclotron frequency of neutron, a species with no charge. The cyclotron frequency is given by:
f_ qB
2jtm
Since the neutron is neutrally charged, it has a cyclotron frequency of 0. This means that a cyclotron cannot be used to
accelerate a neutron. The best answer is choice D.
Questions 49 - 52
49.
Choice C is the best answer. If the battery voltage increases, the droplet must be moved through a stronger electric field.
This requires more work, which supports Option I and invalidates choice B. If the droplet's charge were smaller, less
electrostatic force would act on it, and less work would be required to move it. This invalidates Option II, as well as choices
A and D, and leaves only choice C. Regarding the mass of the droplet, the question asks about the work required to
counteract electrostatic force, which does not depend upon mass. If you reasoned that an increased droplet mass means an
increased charge on the droplet (assuming a fixed p), that would increase the work needed to move the charge against the electrostatic force. Either way, the work will not decrease, which validates Option III. The best answer is choice C.
50. Choice C is the best answer. An electric force exists between any two charges, independent of their orientation in space and
whether or not they are moving. A magnetic force, on the other hand, depends on the alignment of two magnets and requires
that charges be in motion (linear or cyclic) to create the magnetism. These basic difference are behind all of the differences
in the forces. Because motion is only necessary for a magnetic force to exist, a magnetic force varies with particle speed,
while an electric force does not. Choice A is a valid statement, so it is eliminated. As you learned from doing the right hand
rule, the motion vector, magnetic field vector, and magnetic force vector are all mutually perpendicular. For electric forces,
they are either aligned with or against the electric field lines, so they are in fact parallel with the field. Choice B is a valid
statement, so it is eliminated. A moving charged particle can experience both a magnetic force and an electric force, so it is
susceptible to either force. A magnetic force always turns a moving charged particle, because the force is perpendicular to the particle's motion. An electric force can also turn a particle if it's aligned at an angle to the velocity vector. Charged particles in motion will turn until they are moving with the field lines. It is NOT true that a moving particle can only be turned by a magnetic force and not by an electric force, so choice Cis an invalid statement, and is therefore the best answer. If acharged particle is stationary, then itwill experience no magnetic force, no matter where itlies within the magnetic field.
On the other hand, a charged particle will always feel a force when it is immersed in an electric field. This makes choice Da
valid statement, which thereby eliminates it. The best answer is choice C.
51.
particle would accelerate ifadded to the field. As field lines get closer together, the field is said to be stronger. As field lines move apart, the field is said to be weaker. If we follow these rules, we should be able to work through each answer choice. When the particle is moved from Point a to Point b, it is moving perpendicular to the field lines, so no work is being done. In other words, itdoesn't change potential, so no work was done. Choice A is eliminated. A particle would naturally flow from Point b to Point c, and positively charged particles flow from regions of higher potential to lower potential, so choice B is a valid statement, and thereby eliminated. Natural flow for a positive charge is according to the field lines, so choice C is a valid statement, and thereby eliminated. Point a and Point b are found along the same potential line (perpendicular to the
field line), sothey are at the same potential. Choice D isan invalid statement. The bestanswer is choice D.
Choice D is the best answer. As weird as this electric field may appear, this question is simply testing your knowledge of the fundamentals of electric field conventions. Field lines are drawn according to the way in which a positively charged
169
52.
Choice C is the best answer. In order for the particle to pass through the velocity selector unaffected, it must experience no net force. This will occur when forces are equal in magnitude, but opposite in direction. In this case, it means that qvB must
oppose qE. The particle is assumed to be moving from left to right The field arrows for the electric field show the direction
of the force experienced by a positively charged particle. For the magnetic force, the right-hand rule must be applied. In choice A, the magnetic fields points out of the page, so the magnetic force on a particle moving from left to right will be downward. This couples with downward electric force, rather than canceling it out, so the particle will be deflected downward. Choice A, and therefore choice D, are eliminated. In choice B, the magnetic fields points into the page, so the magnetic force on a particle moving from left to right will be upward. This couples with upward electric force, rather than
canceling it out, so the particle will be deflected upward. Choice B is eliminated. In choice C, the magnetic fields points into
the page, so the magnetic force on a particle moving from left to right will be upward. This cancels out the electric force, if the two are of equal magnitude (which is possible at only one velocity), so the particle will not be deflected.
When qvB exceeds qE, the particle will be deflected in the direction of the magnetic force. When qE exceeds qvB, the particle will be deflected in the direction of the electric force. The velocity selector, therefore, works by having the two
forces of equal magnitude oppose one another in direction and thereby cancel one another. The best answer is choice C.
170
REVIEWEXAM EXPLANATIONS
Electricity and
Electric Circuits
Physics Chapter 9
VWA
R
14
R13<* R12v R
u
Switc Switch
\.Swi 3 Switch
R.
Switch 4
Ri
AV\A
R.
Switch5
Switch 2
VvNAA
R6
by
the
Berkeley Review
^"=R"+R~ +R*"+ete*-- (resistors in parallel) Ceq =C\ +C2 +C3 +etc... (capacitors in parallel)
V=IR P=IV P=I2R P=V2/R PEcapacitor=^QV =l^CV2
Important Concept
Circuit elements in series share the same current; Circuit elements in parallel share the same voltage drop
Rj R2 R3 -^/VvVMYWvV
I,
h
Cj
c2
c3
HHHh
cc I M j *~2 1
R Ri x R
OV
2Q
3Q
VW\A
-^A/W^4Q
2Q
1vVW
IvVW^i
-
Ri x R2 Reqq R1 + R2
2x4 2+4
= %Q
Physics
Electric Circuits
Currents
a material that allows for the movement of charge (e.g., copper or silver), while an insulator is a material that impedes the movement of charge (e.g., glass or
plastic). If we wanted a charge to flow through a conductor, we would need to maintain a steady force on that charge. One way to do that is with an electric field E in the conductor, related to charge q and force F by equation (9.1). [This is a rearrangementof equation (8.2) in Section VIII.]
F = qE
(9.1)
Negatively charged electrons flow through a conductor, and experience random motion at great speeds. Yet whenan electric field is applied to the conductor, the
electrons experience not only random motion, but also a small net movement (called drift) in the direction opposite of the electric field. The drift velocity vd of electrons in an electric field is given by equation (9.2), where L is the distance (i.e., length of the conducting material) the electrons travel per unit time t.
v., = L
(9.2)
The flow of charge from one point to another point during a certain amount of time is called an electric current (a scalar quantity). Current is given the symbol I and is defined by equation (9.3). The ampere (amp or A) is the unit of current.
An ampere is the flow of one coulomb of charge per second (i.e., 1 A = 1 C/sec). When studying currents it is often convenient to use the milliampere (mA),
which is 10"3A.
(9.3)
At
Current has a direction in an electric field. It flows in the same direction in which
positive charges flow and in the direction opposite to that in which negative
charges flow (Figure 9-1).
i Current flows in
173
Physics
Electric Circuits
Currents
The drift velocity depends in part on the affinity of charge (electrons) for the conducting material. The drift velocity can be related to the current flowing through a wire. If the potential difference between two points in the wire increases, then the drift velocity, and subsequently the current, will increase. This is the idea behind Ohm's law, which we shall address later in this chapter. When we think of current we consider it to flow as a stream of charge through a wire, with a slightly less resistive path along the surface of the wire than the inside of the wire. Consider a wire (Figure 9-2) with a cross-sectional area A. Suppose that an electron travels a distance L in a given time t across this segment of wire.
Figure 9-2
From this point forward, we shall refer to charge flow as current and follow the standard pnysics conventions that currentis the flow of positive charge.
Example 9.1a
Which of the following changes will increase the transit time of an electron through a conductingwire?
A. B. C. D. Decreasing the mass of an electron. Increasing the resistivity of the wire. Decreasingthe length of the wire. Increasing the current in the wire.
Solution
Decreasing the mass of an electron will make the electron more mobile. If less
mass has any effect, it should increase the average velocity of the electron-a less massive charge in an electric field will have a larger acceleration. This makes
choice A incorrect.
Increasing the resistivity of the wire should make it harder for the electron to
traverse the wire. Although resistivity has not been covered yet, you should be able to use the name ofa property to guess the resulting physics. The "resist" in
the name impliesa hindrance of somesort, in this case a hindrance of current, as current is what flows through the wire. This makes choice B the best answer. At
this point, you can click on choice B and move on if you so wish or if you are
pressedfor time. Forthe sakeof writinga complete answer explanation, we shall address the remaining choices. Ifyou are curious aboutwhy choices C and D are
wrong, then read on.
Decreasing the length of the wire will naturally decrease the amount of time it takes an electron to traverse the wire, assuming it travels at the same rate. This
makes choice C incorrect.
Increasing the current through the wire can mean one or both of the following: more electronstravel through a given region in a given time, or the same number of electrons travel through a given region in less time. Neither possibility will
lead to an increased transit time for an electron. This makes choice D incorrect.
174
Physics
Electric Circuits
Currents
To give you an idea of the drift speed of an electron, consider a household wire
(like the ones used for most appliances), but assume that it carries direct current, DC. For a 10-amp currentapproximately that of a 1200-watt hair dryerthe electrons take 40 seconds to travel 1 cm along the wire.
The correct choice is B.
Example 9.1b
For a fixed potential difference across a resistive wire, the power drain through
the resistor can be increased by increasing the:
A. B. C. D.
neutron density in the wire. length of the wire. temperature of the wire. conductivity of the wire.
Solution
The power drain through a resistor that has a fixed potential difference depends on the voltage drop and the current. The question states that the voltage is fixed, so we need onlyconsider the current through the resistor. Toincrease the power drain throughthe resistor, we need to increase the currentthrough the resistor.
The neutron density has absolutely nothing to do with the current through the
resistor, so choice A can be eliminated immediately. As a wire increases in
length, the charges traversing the wire will encounter more resistance. This reduces the magnitude of the current, which in turn reduces the power drain through the resistor. This eliminates choice B. Increasing the temperature of the
wire will increase its resistance, because the atoms in the wire spread apart from
one another as the temperature increases. The result is that conductivity decreases, resulting in a drop in the magnitude of current. This will reduce the power drain throughthe resistor, so choice C is eliminated.
Increasing the conductivity of the wire results in a greater current passing
through the resistor, which leads to more energy being dissipated. This means that the power drain through the resistor will be greater when the conductivity
of the wire increases.
175
Physi cs
Electric Circuits
Batteries are an important source of electric power. A common type of battery is the zinc-carbon dry cell (Figure 9-3), used in devices that drain minimal power such as flashlights and transistor radios. It is a simple 1.5-V galvanic cell that converts chemical potential energy into an electromotive force (emf) that generates electrical flow. The outer coating of a battery is generally made of inert insulating material that serves as a protective barrier against the outside environment. Immediately inside this protective outer layer is a zinc shell, which
serves as the anode (source of electrons, which in physics we shall consider to be the negatively charged pole). Inside this cup-shaped shell is a thin layer of ammonium chloride (NH4CI) paste, which surrounds another paste comprised of manganese dioxide (MnC>2) mixed with carbon powder. The inner paste
serves as the oxidizing agent in the chemical reaction. At the core of the battery is
a graphite rod, through which electrons may freely flow. A graphite rod, which acts as an internal conducting rod, allows for the passage of electrons to the manganese oxide cathode (endpoint of electron flow, which in physics we shall consider to be the positively charged pole),is positioned within this paste.
Graphite rod
Mn02 paste
-a
NH4CI paste
Zn(s)
Figure 9-3
The cathode and anode of the battery are called terminals. If we attach wires to
off light. Power to light the bulb is supplied by the battery. Electrons leave the passing through the filament of the bulb, the electrons will complete a circuit by
returning to the battery through the wire connected to the cathode.
these terminals and then connect those wires to a light bulb, it glows and gives
anode of the battery and move through the wire leading to the bulb. After
Recall that we have mentioned that the electrical potential difference a moving charged particle experiences as it moves from some region A to some region B (denoted as Vab) is the difference in electrical potential energy APEq at those
two regions divided by the value associated with the charged particle q. This is
the same as saying that there is a voltage change (i.e., a voltage) between region
176
A and region B.
Physics
Electric Circuits
If there is a separation of charge between two points on a device like a battery, and there is a force moving the charge from lower potential to higher potential,
then that device is referred to as a source of electromotive force (abbreviated as
emfand given the symbol e). An electromotive force is not really a "force," but rather an energy-per-unit-charge quantity (much like a potential). We can consider an emf as a voltage source derived from a chemical reaction. The emf
unit is the volt (and 1V = 1J/C).
In electric circuits, a battery is represented by parallel lines of unequal length, as shown in Figure 9-4a. This notation represents a source of emf. The longer line represents the positive terminal (usually at a higher potential) and the shorter line represents the negative terminal (usually at a lower potential). The cathode
is assigned a (+) charge and the anode is assigned a (-) charge. Sometimes you
will see the notation used in Figure 9-4b, which implies that there are multiple cells in series making up the emfsource. This tells us that voltages adds in series.
(a)
(b)
wire
wire
wire
wire
cathode (+)
(-) anode
cathode (+)
(-) anode
source of emf
Figure 9-4
source of emf
Resistivity and Conductivity The resistivity p (rho) of a material is a measure ofhow difficult it is for charges to conduct through the material; higher resistivities are associated with better electrically insulating materials. The resistivity relates to the current density, J,
and the electric field E through equation (9.4). The units of the resistivity are (V/m)(A/m2) which is just Vm/A. However, a volt divided by an ampere (V/A) is called an ohm Q (omega). The units of resistivity can also be written as ohm-meters (Qm). Equation (9.4) is telling us that if the resistivity of a material
is high, then a larger electric field is needed for a given current density. Conductors are considered to be "perfect" when they have zero resistivity, while "perfect" insulators have infinite resistivity.
(9.4)
P=J
a=I
(9.5)
Conductivity a (sigma) is the reciprocal of the resistivity, as shown in equation (9.5). In other words, the larger the conductivity of the material, the better that material isat conducting current. Another way to put this istosay thata material with low resistivity has high conductivity. The unit ofconductivity is l/(Qm).
Table 9-1 lists some resistivities for some common conductors, semiconductors,
and insulators.
Resistivity
Material (Q-m)
Resistivity
Material
Arsenic
Resistivity
Material (Q-m)
9.0 x 1011 108-1012 1.0 x 1016
Insulators
(Q-m)
Conductors
Semiconductors
Silver
1.67 x 10"8
2.24 x 10"8 2.68 x 10"8
Copper
Gold Aluminum
Table 9-1
177
Physics
Electric Circuits
The electrical resistance R of a conductor is given by equation (9.6). Resistance is different from resistivity in that it considers both the material's conductivity and the dimensions of the resistive device. We typically want the resistance of a resistor, as that influences the current flowing through a resistor. The resistance is the ratio of the voltage to the current for a given conductor. The SI unit of resistance is the ohm (Q). One ohm is equal to one volt per ampere (1Q = 1V/A).
_L R=p
(9.6)
Example 9.2a
For the data given, what is the ratio of the resistance of Wire 1 to the resistance of
Wire 2?
Wire 1 2
p (Q-m)
L(cm)
1
A (um2)
6
1
A. B. C.
D. 1:18
Solution
Because we are asked to find a ratio, let's use the ratio method to answer this
question. The relevant equation is equation (9.6). We want the ratio of Rj: R2.
Applying theresistance equation toeach resistor, and dividing, gives:
= 1:18
This is choice D. Notice that we didn't spend time writing out the units (we also
did not waste time writing out the constant p), since all these cancel out. When determining a ratio, you can often omit units and constants from the ratio. You could have used physical intuition to narrow the choices to C or D. Wire 1 is shorter and wider than Wire 2, so Wire 1 should have a smaller resistance than
Wire 2. An analogy to remember is this: Electrons can get through a wider conductor more easily than through a narrow one, just as you can getthrough a
crowded hallway more easily if it is wider. The narrower the wire, the more resistance you encounter. Because Wire 2 is much longer and thinner than Wire 1,the ratioshould be significant; thispointsto choice D.
The best answer is choice D.
Example 9.2b
For the data given, what is the ratio of the resistivities of resistor A to resistor B?
Resistor
A B
R(kQ)
2 4
Radius (mm)
1
L(cm)
3
A.
B.
4:1
2:1
C. 1:2 D. 1:4
178
Physics
Solution
Electric Circuits
Because we are asked to find a ratio, let's again use the ratio method to answer this question. The relevant equation is equation (9.6). We want the ratio of pi : p2Applying the resistance equation to each resistor, and dividing, gives:
2pA-A- = PB Lb.
AA AB
6.
2x3x4
= _6_
24
This is choice D. Notice that just as with Example 9.2a, we ignored the units, because they cancelled out. As long as the respective variables have the same units, then we can ignore them in ratio calculations, as they will cancel out.
Using physical intuition on this question might have proven a bit trickier than mostquestions, because the answer choices are all relatively close to 1. Wire B is double the length and four times the area ofWire A,so Wire Bshouldhave a half the resistance of Wire A if they were made of the same material. Because Wire B
has twice the resistance of Wire A, rather than half the resistance, Wire B must
have a greater resistivity than Wire A. This makes the ratio less than 1, which eliminates choices A and B. To go from half as much to twice as much, something must increase by a factor of 4, so the ratio must involve a 4 rather than a 2. This
eliminates choice C and confirms choice D as the best answer. This is one of those
time consuming questions that no matter whether you used the ratio method or physical intuition, it will take you time and require focus.
The best answer is choice D.
Before we move on from resistors, lefs consider what they do. A resistor opposes the flow of current, and thus, drains energy from an electric circuit. A resistor is
any device in a circuit that hinders current and drains power from the circuit.
Resistors can be a segment of wire or an electrical appliance like a computer.
Ohm's Law
to the potential difference, V, across the ends of that conductor. Consider a section of wire with length L and cross-sectional area A. Across this length of conducting material existsa voltage V. As Figure 9-5 shows, the electrons move in response to this potential difference-but they will move erratically. As the voltage induces the electrons to the right, they interact with protons and other electrons. Such interactions jar and redirect their travel, but they do not prevent
the electrons from flowing as a current.
179
PhysiCS
Electric Circuits
Because the electrons flow in response to an applied voltage, the voltage and the resulting current must somehow be related. As the voltage is increased, the current increases, so V must be directly proportional to I. They are related according to Ohm's law, given by equation (9.7).
Ohm's Law V = IR
(9.7)
Example 9.3a The current through a wire will be the GREATEST when the two ends of the wire
are connected to terminals at:
C.
wire, the bigger the current will be (V = IR, so as V goes up, I goes up). The
all three choices resultin a currentof the same magnitude.
The best answer is choice D.
difference V across some material. The bigger the potential difference across the
potential difference across the wire is 1000 V for choices A, B, and C. Therefore,
Example 9.3b
The voltage across and the currentthrough three different wireswere measured
and reported in choices A, B, and C. For which of the three wires was the
resistance the SMALLEST?
A. V = 100 volts and I = 1 mA. B. V = 1 volts and I = 100 mA. C. V = 10 volts and I = 10 mA.
This question requires that you apply Ohm's law, V= IR. The question is asking for the smallest resistance, so we need to divide the voltage by the current to
determine the resistance.
R=V/l .-. Choice A:100/10-3 =105Q; Choice B: VlO"1 =101 Q; and Choice C:10 j' 10-2 =103 Q
The smallest resistance of the choices is 10 Q.
The best answer is choice B.
180
Physics
Potential and Internal Resistance
Electric Circuits
As we have mentioned, batteries are one particular emfsource. Let's examine the terminals of the emfsource and expand on the diagram shown in Figure 9-4a.
Suppose we label the positive terminal as A and the negative terminal as B, as shown in Figure 9-6. Since the positive terminal (cathode) is at a higher potential than the negative terminal (anode), there will be a potential difference between the two terminals. Recall that electric field lines flow from a positively charged source to a negatively charged source. The electric field in Figure 9-6 goes from terminal A to terminal B. The electric force that a charge between the two terminals experiences is governed by equation (9.1). The direction of that force is
from terminal A to terminal B.
higher V
wire A
E
lower V
wire
(-) anode
'.
Figure 9-6
The potential across the terminals from point A to point B is defined as VAb, ana this is referred to as the terminal voltage (or potential). In this case, a positive charge moves from higher potential to lower potential. Suppose we now connect a wire across the two terminals (Figure 9-6) to complete the circuit. Once the two
terminals are connected, an electric field is established in the wire. Positive
charges can get from terminal A to terminal B in one of two ways: (1) through thefield between the platesor (2) through the wire connecting the cathode to the
anode. Because the wire has less resistance than air, the preferred pathway is
through the wire. Current begins to flow in the wire from terminal A to terminal B. The current in the circuit is given by = VAb = IR. This relationship is saying that as a charge moves through the circuit, the potential increase in the emf e is
equal to thepotential drop VAb as that charge moves through the resistor. As a charge moves through a circuit, it encounters an internal resistance r. Thus,
the current moving through this internal resistance will have a terminal voltage
drop equal to Ir. This is shown in equation (9.8). The current in the external
circuit is still givenby equation (9.7). Substitution of equation (9.7) into equation
Electrical Power
of energy, defined as the ratio of APEq/At. The SI unit of power is the watt,
where 1W = lj/sec. We need a way to relate the power to the current and to the voltage. Recall that we can calculate the change in electrical potential energy as a charged particle moves through a voltage difference using APEq = qV.
_ AqV
P = IV At
(9.11)
181
PhysiCS
Electric Circuits
leads to equation (9.12) and equation (9.13).
Equation (9.11) and Ohm's law, equation (9.7), are two very important equations to remember when considering electric currents. Combining the two equations
(9.12)
P=i
R
P=I2R
(9.13)
This gives us three different equations to choose from when solving for the power drain through a resistor or a circuit. We choose the best equationbased on the variables we are given in the question.
Example 9.4a
Which formula represents the time it takes to accelerate a car of mass m from rest to a speed v, using an electric motor with voltage V and drive current I?
A. t-2EL
mv2
B. t = 2hL
mV C. t =
m
v2
2IV
D. t = 2lV
2Iv
Solution
We usually approach this kind of problem by thinking about units and limiting cases. If you are not too handy with electrical units (especially how they relate to mechanics units), then avoid checking units-you can't check what you don't
know. Try limiting cases.
You need to think about how I, V, m, and v affect the acceleration time t. Think
first about the one that is easiest for you to grasp conceptually. For example, if the car is to reach a higher speed v, what should happen to t? It should go up.
Therefore, the answer is either B or C. Between these two choices, I and m are
switched-V is not. Considering voltage would be a waste of effort-thinkaboutI or m. If the current I increases, what should happen to t? It should decrease; afterall, there is more current to make the car go.Thisleads to choice C.
You could have also singled out this choice if you knew, from solving such problems in the past, that mand v gotogether, or thatI andVgotogether.
You can also solve this problem using energy conservation. Energy questions are ubiquitous in science, meaning thatyou canrelate different physical phenomena (here, kinetic energy and electrical energy) through their energies. Specifically, theelectrical energy generates thecar's kinetic energy:
^electrical= KEcar
The electrical energy comes from the electrical power supplied over some time t
(this is actually the time t needed to accelerate the car to a speed v). Using the
IVt = %mv2
182
Physics
Example 9.4b
Electric Circuits
Which equation the represents rate at which a liquid of mass m, with specific
heat c, is heated by a conducting coil of current I and voltage V?
A.
AT _ mcV
At
AT
B.
= IY
mc
At AT _
At
C.
V mcl
nr
AT
D.
At
IV
Solution
As with Example 9.4a, the cumbersome units make it not so easy to approach the
Forexample, if the material has a low heat capacity c, then it should reach a high temperature and thus experience a large AT. This means that c and AT are inversely related. Therefore, the answer is either B or C. Between these two choices, I is the only variable that is switched. Considering voltage or mass would be a waste of effort, and not help to solve the question. If the current I increases, what should happen to AT? It should increase; after all, there is more
current to heat the solution. This leads to choice B.
You could have also singled out this choice if you knew, from solving such problems in the past, that m and c go together, or that I and V go together.
You can also solve this problem using energy conservation. Energy questions are
ubiquitous in science, meaning that you can relate different physical phenomena (here, heat energy and electrical energy) through their energies. Specifically, the electrical energy generates the heat of the system:
Eelectrical = cjsystem
The electrical energy comes from the electrical power supplied over some time t (this is actually the time t needed to accelerate the car to a speed v). Using the electrical power,equation (9.11), the energiesbecome:
IVAt = mcAT
183
Physics
Electric Circuits
Capacitors
Capacitors
Capacitance
A capacitor is formed from two conductors separated by an insulator. An insulator is a material that does not conduct charge (e.g., rubber or air). A capacitor is represented by equal length parallel lines, as shown in Figure 9-7a.
(a)
Insulator
wire
wire
/
Figure 9-7
Conducting material
cathode (+)
(-) anode
When a voltage is placed between the parallel plates of a capacitor, charge accumulates on those plates (Figure 9-7b). The capacitance C of a capacitor is the
amount of charge q that can be stored per volt of potential difference V across the two parallel plates. This is shown by equation (9.14). The SI unit of capacitance is the farad (IF = 1C/V). Capacitances in electronic devices usually
have values between 5000 uV and 1 pF (where 1 j/F = 10"6 Fand 1 pF = 10"12 F).
c = iL
V
(9.14)
closer together, then greater stability allows more charge to be stored. The capacitance of a parallel plate capacitor can be calculated using equation (9.15), where k is a constant(9.0 x 109 N-m2/C2) and K is the dielectric constant.
C
K
the plates can store (the capacitance). The capacitance will depend on the area A of the conducting plates in the capacitor, the distance d between those plates, and the dielectric constant Kof the insulator between them. Ifthe area of the plates is large, then a large amount of charge can be stored. Similarly, if the plates are
Equation (9.14) basically tells us that the amount of charge that can be stored on a capacitor depends on how hard you push the charge (the voltage) and how much
4rck vd
(9.15)
Dielectrics
(e.g., Mylar, mica, Teflon, etc.) with a specific dielectric constant is placed
Material placed between conducting plates normally does not conduct electric charge. However, if there is a large electric field between the plates, then it could cause the atoms in the dielectric to ionize. This results in positive charge in the dielectric being attracted to the negatively charged plate and negative charges in the dielectric being attracted to the positively charged plate. Conduction of
current can now occur. This phenomenon is called dielectric breakdown.
184
Physics
Electric Circuits
Capacitors
Charging a Capacitor An emf source, such as a battery, can be used to charge a capacitor. Suppose we start with two parallel plates that have no charge (Figure 9-8a). Letcharge move from one plate to the other. As one plate gains positive charge, the other plate becomes deficient in positive charge (i.e., it will be leftwitha negative charge). It does not take much energy to move the first few charges across the plates. However, as more and more positive charges flow to the positively charged plate, they become both repelled by the positively charged plate and attracted by the excess of negative charges on the negatively charged plate (Figure 9-8b). At
some point, no more positive charge can be transferred, and the two plates will be charged with some maximum amount of charge q (Figure9-8c).
(a)
(b)
(c)
+
+ + +
LJ
^
I
K
Despite emf, no charge can flow with an open circuit.
Charge flows and builds up on plates, causing repulsion.
Figure 9-8
The electrical potential energy needed to charge the capacitor is a modified version of equation (8.5). In equation (9.17) we consider the average potential
difference (Vavg) between the plates. The average potential difference is YiV,
because the initial potential (Figure 9-8a) is 0 V and the final potential (Figure 9-
8c) isV. Substituting V2V for VaVg yields a more useful version ofthe equation. APEq = qVavg = q(ViV)
(9.17)
Combining this with equation (9.14), we can express the change in potential energy in two other forms, as shown in equations (9.18) and (9.19):
(9.18)
APEa=i/CV2
APEn .q2 = 2C
(9.19)
How is a capacitor charged? Consider the current over time for circuitshown in Figure 9-9, with an em/source, a switch, a resistor, and a capacitor.
fast current
slow current
Switch
Switch
Figure 9-9
185
Physics
Electric Circuits
Capacitors
Thistype of circuit, with a resistor and a capacitor in series, is called an RCseries circuit Thevoltage V across the emfsource remainsconstant. When the switch in the circuit is closed, the voltage across the resistor (V = IR) varies with time, as does the voltage across the capacitor (V= q/C). The sum of the voltage across the resistor and the capacitor mustbe equalto the voltage across the terminals of the emf source. This is shown by equation (9.20). Solving for the current gives
equation (9.21):
(9.20)
(9.21)
When the switch is open at t = 0 (Figure 9-9a), no current flows in the circuit. Once the switch is closed at t = 1 (Figure 9-9b), the emfsource "pushes" current from the positively charged terminal, around the circuit and on to the negatively charged terminal in a counterclockwise direction. At the instant the switch is first closed, q = 0 C. Plugging in 0 for q into equation (9.21) tells us that the initial current through the circuit is Ii = V/R. As charge begins to accumulate on the
plates of the capacitor, the current flowing back to the negatively charged terminal of the em/source is reduced (Figure9-9c). The value of q/RCin equation (9.21) now increases, causing the current to decrease. Once the capacitor is completely charged at t = 3 (Figure 9-9d), current will no longer flow in the circuit.At that point I = 0 A, and the final charge on the capacitoris qf = VC.
If current passes througha resistor and flows to a capacitor, then both the current
through that capacitor, equation (9.22), and the charge on that capacitor,
these equations is referred to as the time constant.
(9.22)
equation (9.23), will change exponentially with time. The quantity RC in both of
UI^/RC)
q=qf(l-e-t/RC)
(9.23)
Larger capacitors require a longer time to charge and discharge, as they have more charge to store or lose. Larger resistors increase the charging and discharging time, because they reduce the current flow that occurs during charging and discharging. Graphs of the capacitor discharge current and storing charge are plotted as functions of time in Figure 9-10, along with their time constants. These times represent how long it takes for the discharge current and storing chargeto change by 1/e and 1 - (1 /e), respectively.
Discharging Capacitor Charging Capacitor
qmaxd - 7)
t = RC
t = RC
Figure 9-10
186
Physics
Example 9.5a
Electric Circuits
Capacitors
Two parallel plate capacitors of equal size are charged by a power supply of voltage Vsuppiy. What is true of these capacitors when their maximum storage
charge is plottedas a function of supply voltage?
A
max
S^
S*\
A. Capacitor B has a stronger dielectric between the plates; Capacitor A has a higher breakdown voltage. B. Capacitor A has a stronger dielectric between the plates; Capacitor B has a higher breakdown voltage. C. Capacitor B has a stronger dielectric between the plates; Capacitor A has a
lower breakdown voltage.
Let's use the multiple-concepts approach to figure out dielectric strength and breakdown voltage separately. Regarding dielectric strength, a capacitor with a stronger dielectric can store more charge (all else being equal)-that's partly why dielectrics are used. Because Capacitor A reaches a greater Qmax/ it must have a stronger dielectric, which rules out choices A and C. Regarding the breakdown voltage, the plot shows that Capacitor B loses its charge at a lower voltage than Capacitor A does. Capacitor B must have the lower breakdown voltage.
The best answer is choice D.
Example 9.5b
Two different capacitors, each connected to an identical voltage supply but a different resistor, are charged. Their charge, as a function of time, is plotted to
the left. What is true of the two RC circuits?
A. B. C. D.
A has a larger capacitor; B has a larger resistor. B has a larger capacitor; A has a larger resistor. A has a larger capacitor; A has a larger resistor. B has a larger capacitor; B has a larger resistor.
Solution
Let's again use the multiple-concepts approach to figure out capacitor size and
resistor size separately. Regarding capacitor size, Circuit A gains a larger total
charge given the same voltage, so Capacitor A must be larger than Capacitor B. This rules out choices B and D. Regarding the resistance, the plot shows that Capacitor A gains its charge at a faster rate than Capacitor B does, so it must experience less resistance. Resistor A has a lower resistance than Resistor B.
The best answer is choice A.
187
Physics
Electric Circuits
Electric Circuits
Electric Circuits
Kirchhoffs Rules
Electric circuits can become rather complicated at times. The two Kirchhoff's rules that will help us analyzecomplicated circuits are Kirchhoff's loop rule and Kirchhoff's junction rule. Fortunately, the MCAT tests only RC circuits, which
follow those basic rules. Between Ohm's law and two Kirchhoffs rules, you should be able to navigateany RC circuits you'll encounter on the MCAT.
zero (Vdrop = IR =1(0) = 0). As the positive charge moves from point Bto point C
it encounters a resistance R. There is a potential decrease across the resistor (Vbc = -IR). From point C to the anode, the change in voltage (potential) is again zero. Once the charge reaches the anode, it stops moving, so its "potential" to move is zero. All of the voltage from the emf source has been used up. Thus, the initial voltage at the cathode is equal in magnitude to the voltage dropped as current
traverses the circuit (Vdrop = -IR)- The energy that is expended to do this is the
chemical energy of the emf, or Eceii. The sum of the voltage changes around this closed circuitmust add up to zero. If the charge were to move from point D back
to point A, it would encounter the emf.
vdrop ="IR
I
<
T3
wv Y
Ri
B
o
II
9"
II
O
4 i 4h
Ri
t A
Rr
(-)
(+) A
I
>
(+)
(-)
junction and divides. The total currentflowing through the pathwaysleaving the junction must equal the current that entered the junction. In other words, all of the electrons entering the junction must be accounted for~no electrons fall off of the wire or jump onto the wire.
For example, consider the diagram in Figure 9-14. As the current I leaves the positive terminal of the emf source, it encounters a junction at point A. The current I entering that junction must equal the sum of the currents Ii and I2 that leave the junction. In other words, I = Ii + I2. This relationship allows us to determine currents after they have been divided through parallel pathways.
188
Physics
Example 9.6a
Electric Circuits
Electric Circuits
What are the values for the various unlabeled currents in the circuit below?
6.17 A
rVWS
2.33 A
HWH
5.02 A
-JWV-
-W-
HfiH
A. B. C. D. I3 = 3.84A;l4 = 1.15A;l6 = I3 = 3.16A;l4 = 1.15A;l6 = I3 = 3.84A;I4 = 1.15A;I6 = I3 = 3.16A;l4 = 7.32A;I6 = 6.17A 6.17A 4.33A 4.33A
HMH
Solution
This question is just an application of Kirchhoff's junction rule. The current entering the first junction is 6.17 amps, so the current leaving the last junction,!(,, should also be 6.17 amps. This eliminates choices C and D. From here, we can note that 2.33 + I3 = 6.17 or that 5.02 + 14 = 6.17. Solving both relationships concludes that I3 = 3.84 amps and that I4 = 1.15 amps. The value of I4 doesn't help to solve the question, but I3 helps differentiate between choices A and B.
The best answer is choice A.
Example 9.6b
HWV-i
-Wr- ,1 -tfh
A. Ia>Ic>2.62A
8.23 A
Rd = 2.5Q
1.89 A
2.22 A
This question doesn't involve as much math as it would seem at first glance. First and foremost, Kirchhoff's junction rule tells us lb = Id = 8.23 A. This eliminates choices Band C. Next we need to compare Ia to Ic. The total current splits in such a way that Itotal = 5.61 + Ia and Itotal = 1-89 + 2.22 + l0 so setting the relationships equal to one another we get 5.61 + Ia = 4.11 + Ic. For that to hold true, Ic > 1&
which eliminates choice A. (Ia = 2.62 A, lb = 8.23 A, Ic = 4.12 A, and Id = 8.23 A)
The best answer is choice D.
189
Physics
Example 9.7a
Electric Circuits
Electric Circuits
Given a 12-volt battery in the circuit below, what is the voltage across R2 and the current through R3, if each resistoris 4 Q and Ii is 2 A?
wRi
vw R2
R,
vw
A. B. C. D.
V2 = V2 = V2= V2=
Solution
Let's use Kirchhoffs loop and junction rules to solve this one. Applying the loop rule on the inner loop (i.e., the one that includes the battery, Ri, and R2), we get:
V = I1R1 + I2R2
As current flows around the loop from cathode to anode, the voltage drops from 12 to 0, decreasing upon crossing each resistor (e.g., -I1R1 and -I2R2)- Based on
the battery orientation, the current flows counterclockwise and passes through Rl before splitting at the junction. Based on Kirchhoffs junction rule, the current entering the junction (Ii) mustequalthe sum of the currentsleaving the junction (12 + l3)- Because 2 A enters the junction and R2 = R3, both I2 and I3 = 1 A. This
makes choice Athe best answer. To be complete, lefs solve for Vdrop 2V2 = -I2R2 = (1 A)(4 Q) = -4 V
Example 9.7b
What is the voltage drop across R2 and the current through R3 in the circuit below if the current leaving the battery is 6 A and that all resistors are 3 Q?
V
rn/W
Rl
Ro
MA
R2
VW1
A. B.
C.
D.
V2 = 2 volts, and I3 = 3.3 amps V2 = 3 volts, and I3 = 2.0 amps V2 = 6 volts, and I3 = 4.0 amps V2 = 12 volts, and I3 = 4.0 amps
190
Physics
Solution
Electric Circuits
Electric Circuits
the upper current and lower current must equal 6 A and the ratio of the upper current to the lower current must be 1 : 2. This means that the current through the upper pathway is 2 amps and the current through the lower pathway is 4
amps. This eliminates choices A and B.
Let's use Kirchhoff's junction and loop rules tosolve this one. Applying the junction rule, we know thata current of 6 amps enters the junction and is split between the two pathways. The two pathways have resistances of6 Q (Ri + R2 = 3 Q + 3 Q = 6 Q) and 3 Q (R3 = 3 Q) respectively. Because the upper pathway has twice the resistance of the lower pathway, it will have half of the current. The sum of
The voltage drop current across resistor 2 is -I2R2- The current is 2 amps and the
resistance is 3 ohms,so the voltage drop must be:
V2= I2R2 = (2 amps) (3 ohms) = 6 volts
V2 is 6 volts, which eliminates choice D.
The correct choice is C.
Circuits can have several circuit elements. As current from the cathode passes
through the wiring and to the anode, it will encounter the various circuit elements within the circuit. The relative alignment of the circuit elements can be described as either in series or in parallel. In series, the circuit elements are connected in a direct path, where current passes through each circuit element. In parallel, the circuit elements are part of different pathways, where one circuit element can be thought of as being a part of an alternative pathway to the other
circuit element. Circuit elements in series share the same current, while circuit
in series (e.g., Rj, R2, R3, etc.) with a single equivalent resistor Req. In other
words, we need to determine what size single resistor would have the same impact on the current as all of the resistors in series combined. For resistors in series this is simple, because connecting multiple resistors in series is like making a longer resistor. Resistors connected in series are additive, as in equation (9.24):
Requivalent = Rl + R2 + R3-
(9.24)
When is a resistor in series with other resistors? This is the case when the same
current can flow through each of the resistors without branching between them, as shown by the circuit in Figure 9-15:
WWAVMM
Ri
R2
R,
Figure 9-15
191
Physics
Electric Circuits
Electric Circuits
Resistors in Parallel
There will be times when it will be necessaryto mentally replace several resistors
in parallel with a single equivalent resistor. Lefs consider what happens when
by-side fashion. This would in essence make a wider resistor. Given that
approximation can assume that the resistance would decrease. This can be done
.=J^+J,
we have several resistors in parallel. Ifs like stacking several resistors in a sideresistance decreases with an increasing cross-sectional area, we at first
by using equation (9.25).
(9.25)
^equivalent Rl
R2 ^3
When is a resistor in parallel with other resistors? This is the case when both
sides of each resistor are connected to a common junction, as shown by the
circuit in Figure 9-16.
Ri
M/fr
Ri
^vwR,
^-AMr
Figure 9-16
Capacitors in Parallel
Now lefs consider what happens when we have several capacitors in parallel. Ifs like stacking several capacitors in a side-by-side fashion. This would in essence make a wider capacitor. Given that capacitance increases with area of the plates, we at first approximation can assume that the capacitance should
increase. The equivalent capacitance when capacitors are added in parallel involves the addition of eachcomponent capacitor. Equation (9.26) allowsfor the
^equivalent = Q. + C2 + C3...
(9.26)
An example of three capacitors in parallel is shown in Figure 9-17, where each capacitor will share the same voltage,but not the same charge build up:
-qi
.iiJL-q2
-LLi-q3
'! -n +q1 + +
C2 1 +CJ2 + +
C3 + + +q3
Figure 9-17
192
Physics
Capacitors in Series
Electric Circuits
Electric Circuits
Equation (9.27) allows for the calculation of the equivalent capacitance (Ceq) of
several capacitors in series. [Note that the form of this equation is different from the form of the equation for resistors in series.]
.=J-+ J^ +.
^equivalent Cl
C2 C3
(9.27)
What is TRUE of the voltage across, current through, and power loss by two
unequal resistors connected in series?
A. The larger resistor has a bigger voltage drop and dissipates more power;
both resistors have the same current.
B. The larger resistor has a smaller current and dissipates less power; both resistors have the same voltage drop. C. The larger resistor has a bigger current and smaller voltage drop; both resistors dissipate the same power. D. The larger resistor has a smaller current and bigger voltage drop; both resistors dissipate the same power.
Solution
When current flows through a series resistor circuit, as in Figure 9-15, current can flow along only one path (just as a water current would flow, if this figure were a top view of plumbing). The same current must flow through each part of the circuit; each resistor must have the same current, regardless of its size. Because all of the resistors have the same current, only choice A is possible. But for the sake of review, lefs consider the voltage drop and power loss for each resistor. Given that each resistor has the same current, the larger resistor will have a larger voltage drop, since:
Vdrop = "IR
Because the resistors have the same current, we must use a version of the power equation with I in it. Given that we are determining power for different sized resistors, we should choose the form of the power equation that has I and R.
P = I2R
Because the current is the same in each resistor, increasing resistance will
increase the power. The larger resistor will dissipate more power, since the power equation shows that power is directly proportional to resistance (P R). The relationships for resistors in seriessame I, bigger R has bigger V and P hold generally for any number of resistors in series. Know these relationships.
The best answer is choice A.
193
Physics
Example 9.8b
Electric Circuits
Electric Circuits
What is true of the voltage across, current through, and power loss by two unequal resistorsconnected in parallel?
A. The larger resistor has a bigger voltage drop and dissipates more power;
both resistors have the same current.
B. The larger resistor has a smaller current and dissipates less power; both
resistors have the same voltage drop.
C. The larger resistor has a bigger current and smaller voltage drop; both
resistors dissipate the same power.
D. The larger resistor has a smaller current and bigger voltage drop; both
resistors dissipate the same power.
Solution
When current flows through a parallel resistor circuit, as in Figure 9-16, current can flow along different paths, suggesting that the current is not necessarily the same along each path. However, parallel resistors will have the same voltage drop across them, because each end makes a direct (i.e., no intervening circuit elements) connection with the same voltage source. This means that choice B is the only possible answer. But for the sake of review, lefs consider the current through and power loss for each resistor. Given that each resistor has the same voltage drop, the largerresistor must have a smaller current, since: I=V
R
Remember the old saying, "Choose the path of least resistance"? This applies to
current. The above equation is how that statement is said in math. Because the
resistors have the same voltage drop, we must use a version of the power equation with V in it. Given that we are determining power for different sized resistors, we should choose the form of the power equation that has V and R.
P = Yi
R
Because the voltage drop is the same in each resistor, increasing resistance will decrease the power. The larger resistor will dissipate less power, since the power equation shows that power is inversely proportional to resistance (P 1/R). The relationships for resistors in parallel-same V, bigger R has smaller I and P-hold generally for any number of resistors in parallel. Know these
relationships.
The best answer is choice B.
Example 9.9a
What is true of the voltage across, charge stored on, and energy stored by two
unequal capacitors connected in parallel?
A. The larger capacitor has a smaller voltage gain and stores less energy; both capacitors store the same charge. B. The larger capacitor stores more charge and more energy; both capacitors have the same voltagegain. C. The larger capacitor stores more charge and has a smaller voltage gain; both
capacitors store the same energy. D. The larger capacitor stores less charge and has a larger voltage gain; both
capacitors store the same energy.
194
Physics
Solution
Electric Circuits
Electric Circuits
When charge stores in a parallel capacitor circuit, as in Figure 9-17, the voltage
gain across each capacitor will be the same (for the same reasons resistors in
parallel have the same voltage drop). Given that the voltage is the same, the
larger capacitor will store more charge, since Q = CV.
The larger capacitor will store more energy, since the energy equation can be
written as:
APEn =lCV2
q 2
Since each capacitor has the same voltage across it, the largercapacitor will store more energy. The relationships for capacitors in parallel-same V, bigger C has
Example 9.9b
What is true of the voltage across, charge stored on, and energy stored by two unequal capacitors connected in series?
A. The larger capacitor has a smaller voltage gain and stores less energy; both capacitors store the same charge. B. The larger capacitor stores more charge and more energy; both capacitors have the same voltage gain. C. The larger capacitor stores more charge and has a smaller voltage gain; both capacitorsstore the same energy. D. The larger capacitor stores less charge and has a larger voltage gain; both capacitorsstore the same energy.
Solution
When charge stores in a series capacitor circuit, as in Figure 9-18, the charge stored on each capacitor will be tiie same. For example, notice the section of wire between Ci and C2 in Figure 9-18. Before charging begins, there is no net charge on the wire; after charging, there must still be zero net charge, because charge cannot be created, and that section of wire is isolated from any charge sources. Thus, one capacitorgets +q, while the other gets -q from that section of wire. This same charge separation occurs in each isolated section of wire. Since capacitors are connected to these sections, each capacitor must have the same charge. Given that the charge is the same, the larger capacitor will have a
smaller voltage gain, since:
V =
The largercapacitor stores less energy, since the energy equation is written as:
APEq =l2i 4 2 C
Because each capacitor has the same charge on it, the larger capacitor must store less energy. The relationships for capacitors in seriessame Q, bigger C has
smaller V and PEqhold generally for any number of capacitors in series. Know
these relationships.
The best answer is choice A.
195
Physics
Electric Circuits
Electric Circuits
Example 9.10a
R1 = 2Q
#k
R2 = 3Q
I3 = 0.5A
I. Req = 4ohms
II. R3 = 6 ohms III. Itotal = 1-5amps
As a general rule, you should attack these questions by starting with an analysis of the feature they give you the most of. In other words, we are given two of the three resistances, so lefs start by analyzing resistance. Unfortunately, we can't do
much tosolve for R3 orReq. We are limited in what wesolve for, so this question
forces us to work backwards from the answer choices. Because there is no "none
of the above" answer, we have to assume that at least one statement is valid. So
We can solve for Req by solving the parallel pairfirst, and then adding that toRi.
\4
Test Tip
Calculation Shortcut
A short cut that willsavea largeamount of time is to rewriteequation (9.25). For two resistors in parallel, the equivalent resistance is their product over their sum.
RlXRn
Req = R2 + R2 1
If Req is 4 Q and the battery is 6 V circuit, then Itotal is 1.5 amps. All three
statements match. Lefs considerthe values for the lower segment of the circuit.
12 = 1.0A
l! = 1.5A
6V 3V
R2 = 3Q
-3V
OV
R1 = 2Q
-3V
13= 0.5A
vw1 R3= 6C
The Berkeley Review
196
Physics
Circuit Calculation Shortcut
Electric Circuits
Electric Circuits
Example 9.10a introduced a shortcut for determining the equivalent resistance for two resistors in parallel. This same shortcut also works for capacitors in series. The idea behind the shortcutis simple: You don't have to show your work on the MCAT, so you might as well manipulate your common formulas into an easier to use form. Solefs consider the calculation oftwo resistors in parallel.
1 _ 1 + 1 _ R2 + Rl ^equivalent Rl R2 Rl * R2 Rl * R2 R2 + Rl _Rl+R2
Rl x R2
r
Ri x R2
Ri x R2
Requivalent Rl * R2
Example 9.10b
What arethe current leaving the cathode, the current through Ri, andReq for the
following electrical circuit?
12 V
m/WMA-i R1 = 2Q I2= 4A
I3 = 2A
M
A. B. C D. Itotal = 6 A,Ii = 4 A, and Requivalent = 2 Q Itotal = 6A,Ii=2A,andRequivalent = 4Q Itotal = 10A,Ii = 4 A,and Requivalent = 2 Q Itotal = 10A,Ii = 6 A,and Requivalent = 4fi
Solution
At first glance, it seems like this is a difficult question. But if we attack the question using Kirchhoff's Junctwn rule, we should be on our way to the answer. Resistors 1 and 2 are in series, so they will share the same current. I2 is given as 4 amps, so Ii must also be 4 amps. This eliminates choices B and D. The current splits at the junction into two pathways: the upper path and lower path. The current through the upper path is 4 amps and the current through the lower path is 2 amps, so the current going into the junction, Itotal/ is 4 + 2 amps. Because Itotal is 6 amps, the best answer is choice A. The equivalent resistance for the circuit can be found using Ohm's law. For the
overall circuit, we get:
197
Physics
Electric Circuits
Electric Circuits
Lefs apply this to some simple circuits. Figure 9-19 shows three examples of simplified calculations thatyoucando in your head.
RX = 8Q R2 = 4Q
RaxR2
Rj + R2
8 + 4 12 3
Rlx R2
9x3
Rx +R2 ~ 9+3
~ = 7 = 2.25Q
12 4
27
R1 = 9Q
R2= 3Q
Ci=2C
C2= 6C
-\\
C!xC2
Ci +C2 =
Figure 9-19
2 + 6
A shortcoming of this technique is that it applies only if there are two resistors in parallel or two capacitors in series. When there are three or more resistors in parallel, then you need to analyze the circuit two at a time. Figure 9-20 shows an example of the simplified calculation applied to three resistorsin parallel.
n/WH Rj = 6Q
R2= 3Q
6x3 6 + 3
f-20
16 10 = 1.6Q
-toR3= 8Q
2x8 2 + 8
Figure 9-20
Lastly, before leaving circuits and circuit calculations, lefs rehash the differences between parallel circuit elements and series circuit elements.
Series Circuit Elements Same current Parallel Circuit Elements
Different voltage drop Increased equivalent resistance Reduced equivalent capacitance Larger resistors drain more power
Reduced equivalent resistance Increased equivalent capacitance Smaller resistors drain more power
(P =I2R(Pf as Rf)
Devices are dependent on one another
(P =V2/R(PtasR|)
Devices are independent of one another
198
Physics
Electric Circuits
Alternating Current
the cathode to the anode). For 99% of the electricity generated for commercial use, however, the voltage source is not constant but instead is alternating, so it results in an alternating current (AC). A simple AC circuit is shown in Figure 921; the new circuit element is the alternating voltage source (the sine wave in the
circle indicates AC).
Figure 9-21
AC is used instead of DC, owing to inherent inefficiencies (e.g., heat loss) in DC circuits that can be overcome when the voltage alternates. In addition, with AC circuits, there are brief instances where the current and voltage are zero, meaning that ifs a safer circuit if one were to accidentally contact it. It is easier to let go of a circuit when it has no current running through it. Because of this alternating voltage, the current also alternates with time (Figure 9-22). In the United States, this oscillation frequency is typically 60 Hz.
time
time
Figure 9-22
Recall that we defined power in equation (9.11) as P = IV. The power that we are usually interested in is the average power. The relationship between average power and current involves the root-mean-square current Inns quantified in equation (9.28), while the relation between average power and voltage involves the root-mean-square voltage Vmis quantified in equation (9.29). As plotted in Figure 9-22, the root-mean-square of something is just a way to describe a non
zero average value of a quantity that can be either positive or negative. This results in an average power of Pavg = Irms^rmsCopyright by The Berkeley Review
199
Physics
Electric Circuits
Alternating Current
Equations (9.28) and (9.29) describe the root-mean-square current and voltage
relative to the maximum current and maximum voltage respectively.
Irms =-r
V2
(9.28)
Vrms =^
Example 9.11a
V2
(9.29)
Doubling both the root-mean square current through and root-mean square voltage across a resistor in an AC circuit will increase the power drain by a factor
of:
A. 1.
B. V2.
C. D. 2. 4.
Solution
This question is a great example of irrelevant information being intimidating. The fact that ifs an AC circuit as opposed to a DC circuit, with which we are more familiar with in terms of physics exposure, means that we must consider the Irms and Vnns instead of just I and V. The reality is that it just doesn't matter, because it will be solved in the same fashion as a DC circuit question is solved. Doubling both factors Irms and Vrms in equation (9.11) results in a four-fold increase in the power drain, since the current and voltage are multiplied. Don't be scared when you see an "rms" in a problem about AC circuits; the conceptual aspects of current, voltage, and power are still the same as they are for DC
circuits.
Example 9.11b
Doubling the maximum voltage in an AC circuit will increase the root-mean square voltage by a factor of:
A. 1
B. V2
C. D. 2 4
Solution
According to equation (9.29), the root-mean square voltage is directly proportional to the maximum voltage. This means that if one of the two were to increase, then the other value must increase by the exact same factor. Doubling
one will therefore double the other. Because Vmax is doubled, V^s should also be doubled. Be careful not to fall for the trick of seeing a square root in the equation and blindly assuming that the answer must also include a square root
term.
200
I.
II.
(1-7)
(8-14)
(15-21)
(22 - 25)
III.
The main purpose of this 25-question set is to serve as a review of the material presented in the chapter. Do not worry about the timing for these questions. Focus on learning. Once you complete these questions, grade them using the answer key. For any question you missed, repeat it and write down your thought process. Then grade the questions you repeated and thoroughly read the answer explanation. Compare your thought process to the answer explanation and assess whether you missed the question because of a careless error (such as misreading
the question), because of an error in reasoning, or because you were missing information. Your goal is to fill in any informational gaps and solidify your reasoning before you begin your practice exam for this section. Preparing for the
MCAT is best done in stages. This first stage is meant to help you evaluate how well you know this subject matter.
Passage I (Questions 1 - 7) Resistors are often made of carbon-based compounds and have a cylindrical shape. Such resistors have a resistance that depends on their dimensions, as is shown in Figure 1.
1 1
3.
I 1 *
length
* %
1 I
0.6 cm
0.9 cm
w+ m
A. B. C. D.
I and HI only II and IV only I, II, and III only I, HI, and IV only
Resistors are often used in Joule heating experiments to raise the temperature of liquids or gases by a desired amount. The resistance to current flow through a resistor connected to a power supply leads to heat dissipation in direct proportion to the current through the circuit The resulting temperature increase of a fluid depends upon this resistor, as well as the fluid's specific heat and the heating time. Figure 2 shows typical data for Joule heating experiments in various fluids. Each trial lasts 10 minutes, all fluid samples are 10 gm, and each resistor is connected to a 12-V DC voltage source.
DO
Where p is the resistivityof a material, A represents the area of a cylindrical resistor, and L represents the
length, the resistance of the resistor is found to be:
A. A
pAL.
B.
C. D.
?A/LPL/AP/AL-
O
DO
25 kQ
5.
DlOOkQ
O
5
D
D
and with equal radii, Ri and R2, where R\ is longer than R2, whatis truewhen the twoare in parallel?
A. Ri dissipates more heat than R2. B. R2dissipates more heat than R\.
C (cal/gm-K)
C. Ri experiences a greater voltage drop than R2. D. R2 experiences a greater voltage dropthan Ri.
6.
1.
B. A 0.50 cm Cu resistor connected to a 12V battery in200mLof a solution with C = 0.80cal/g-K C. A 0.50 cm Cu resistor connected to a 6V battery in
200 mLof a solution with C = 1.20cal/g-K D. A 0.50 cm Cu resistor connected to a 12V battery in 200 mLof a solution with C = 1.20cal/g-K
7.
Two resistors of unequal resistance aligned in parallel experienceall of the following EXCEPT:
A. an equivalent resistance of R1R2
Rl +R2
rapidly than the known resistor. Comparing the two resistors, the unknown resistorwould likely have:
A. B. C. D.
a largerresistance and a largervoltage drop. a largerresistance and a smallervoltage drop. a smaller resistance and a larger voltage drop. a smaller resistance and a smallervoltage drop.
202
9.
resistors. Batteries convert chemical energy, through oxidation-reduction reactions, into electrical energy (in the form of electrical flow). Resistors convert electrical flow into heat, light or work. Examples of resistors include a heating coil in an electric stove, the filament in an incandescent bulb, or the rotating loop of an electric motor.
Electrical circuits that consist of more than one resistor
and more than one battery can be hooked up in one of two ways: in parallel or in series. Six unique circuits with resistors and batteries in both series and parallel are shown in Figure 1. The batteries have voltage V and the resistors
resistance R. Ohm's Law relates the variables of a circuit,
where I is current V = IR
A. Both drain less power. B. Both drain more power. C. The power drain does not change in either resistor.
11.
If Ri has greater resistance than R2 in Circuit V, which resistor drains more power?
WW"
Vi-=F
Ri R2
WWCircuit II
T X
vWA
Ri R2
=r^V2
Circuit in
A. VTotaI = Vi+V2;Req = Rl + R2
V,"^
v2 R2
Rl + R2
WW
Circuit IV
iWWRi VlT R2
v2
i_VWv^
Circuit V
13.
What is true for a circuit having two resistors, Ri and R2, of unequal resistance?
I. Resistors in series experience the same current.
V, T
V2
R2
II. Resistors in parallel experience the same voltage. HI. They have equal power drain if voltage is equal. A. I and II only B. I and III only C. II and III only
D. I, II, and III
Circuit VI
4=-
v2
r,
R2
Figure 1
8.
14.
How do total currents compare in Circuits I, II, HI, and IV, given Vi = 6V, V2 = 6V, Ri = 2Q, and R2 = 4Q? A. Ii = Im > Iiv > III
B. Iiv > III > Ii = IlII C. Ii > Im > Iiv > III D. iiv > in > ii > im
Vcircuit I = Vcircuit II if Rl = R2
D- Vcircuit I = Vcircuit II if Rl * R2
203
17.
Batteries, resistors, and capacitors are three of many circuit elements that may be connected in series, in parallel,
or in combinations of both to achieve a desired effect Circuit
elementsin parallel share the same voltage difference. Often, the operation of a circuit may be changed by the opening or closing of a single switch, which can change the circuit elements from being in series to being in parallel. This is observed in the following diagram of an RC circuit, which
contains two switches: 18.
(Ri +R3)
D.
E
RI+52R3
Ro x Rj
Ri
Switch 2
Immediately after Switch 1 is closed (Switch 2 is open) and the capacitor is still negligibly charged, what is the current through R3?
A.
0
R3
R2
Switch 1
B.
R,
C.
Figure 1
D.
(Ri +R3)
8
Ri +
R2 + R3
Rt X Ra
19.
Once the capacitor is fully charged, Switch 2 is closed (Switch 1 remains closed). Closing Switch 2 will have
what effect on the total resistance of the circuit?
A. The total resistance will increase.
B. The total resistance will decrease.
C=^
AV
where C is the capacitance, Q is the charge on the plates, and AV is the potential difference across the plates. These equations let us determine voltage, current resistance, and
capacitance at any given point within the circuit.
D. Whether the total resistance increases, decreases, or remains unaffected will dependon the numerical
values of the resistors.
15. When Switch 2 is closed, is the capacitor in the above circuit in parallel or in series with any other circuit
element?
20.
After Switch 1 has been closed for a long time (with Switch 2 open), the capacitor becomes fully charged.
The charge on the capacitor can now be writtenas:
A.
B. C.
A.
No.
0
Ce
C*6*lv2- R3
R, + R2 + R3
D.
Oe_R3
R1 + R3
16. Initially, the capacitor is uncharged. Switch 2 is left open, while Switch 1 is closed. Immediately after Switch 1is closed, what is thecharge on thecapacitor?
A.
B.
21.
If Switches 1 and 2 are both closed and if the capacitor is allowed to charge completely, the current through R2
will exceed the current through:
A. R3, only if R3 > R2. B. R3,onlyifR2>R3.
C. C, only if R2 > Ce.
Ce
0
C.
Ce
(Ri + R2)
D. CIR2
204
A.
22. What happens over time to the capacitance of a capacitor, as the space between its plates is filled at a constant rate with a polar solution? A. The capacitance remains constant until the volume is completely filled, then the capacitance immediately drops to the new value of KC0.
B. The capacitance remains constant until the volume is completely filled, then the capacitance immediately increases to the new value of KC0.
B. C.
D.
C. The capacitance gradually decreases as the solution is added until the volume is completely filled, then the capacitance remains at the new value of K'Q,.
D. The capacitance gradually increases as the solution is added until the volume is completely filled, then the capacitance remains at the new value of KC0.
23. When a capacitor is fully charged and before it begins to discharge, the potential difference across the capacitor plates is:
A. 0 volts.
24. The maximum charge that can be stored on a capacitor depends on:
I. the capacitance of the capacitor.
II. the emf of the battery. HI. the equivalent resistance of the circuit
IV. the power drain of each resistor in the circuit. A. I and HI only B. II and HI only
C. I and II only D. II only
1. C 2. A 7.
3. A 8 A
4.
5.
6. C 11. B 16. B
21. A
9. D 14. A 19.
24. B
12. B
17. B
22. D
205
Choice C is the best answer. According to Figure 1, as the cylinder radius increases, the resistance of the resistor decreases.
This rules out choices B and D. Now, for a fixed cylinder radius, the longer resistor will have the larger resistance. This
makes choice C a better answer than choice A. Keep in mind that R= pL/j\ where Ris resistance, p is resistivity, Lis
resistor length, and A is the cross-sectional area of a cylindrical resistor. According to the equation, as the length of a
cylindrical resistor increases, its resistance increases. As the width of a cylindrical resistor increases, its resistance decreases.
The best answer is choice C.
2.
Choice A is the best answer. When in series, all circuit elements share the same current, so two resistors in series have the
same magnitude of current. Since P=IV and I is the same for both resistors, the resistor that uses more power (i.e., heats
more rapidly) must have the larger voltage drop. This rules out choices B and D. Since V=IR and I is the same for both resistors, the larger voltage drop occurs across the larger resistor. This means that choice A is a better answer than choice C.
For resistors in series, the current is the same through each resistor, so the relative power can be most easily ascertained
using P=I2R. This tells us that power drain is directly proportional to the resistance. The best answer is choice A.
3. Choice A is the best answer. Because all of the heating experiments are done for the same 10-minute duration, the AT axis
in Figure 2 directly relates to the heating rate. To answer this question, therefore, let's see how mass, specific heat, voltage,
and resistance affect the temperature increase. According to Figure 2, increasing the specific heat, C, decreases the temperature increase AT. This may seem intuitive, because a greater heat capacity requires more heat so the temperature
does not rise as much for a given amount of heat You may also recall that q = mCAT, where a larger C would equate to a
smaller AT, q and m being constant This invalidates Statement II, and eliminates choices B and C. Between choices A and
D, we need only consider Statement IV. According to Figure 2, for a given specific heat, the smaller resistor has the larger
temperature increase. This makes Statement IV invalid. The best answer is choice A.
4.
Choice C is the best answer. You could answer this straight from your memory, if you happen to recall the equation for resistance in a cylindrical resistor (or segment of wire). If you do not recall the equation, then Figure 1 lists the pertinent
data to deduce the relationship between the key variables. All choices have resistivity, p, in the numerator, so to determine
the correct answer, we need only consider Aand L. The longer resistor (0.9 cm versus 0.6 cm) has higher resistance at equal
radius, so resistance increases with L. Thiseliminates choices B and D. As the radius increases, theresistance decreases, so resistance must beinversely proportional to the cross sectional area. This eliminates choice A and leaves only choice C. The
best answer is choice C.
5.
Choice B is the best answer. The longer resistor of two resistors with equal cross sectional area and equal resistivity has
greater resistance. When the two resistors are in parallel, the voltage drop across each resistor is equal but more current flows through the smaller resistor, so the resistor with lower resistance drains more energy and therefore dissipates more heat. The resistors experience the same voltage drop inparallel, sochoices C and D areeliminated. Given that R2 isshorter
than Ri, it has less resistance and therefore drains more energy and dissipates it in the form of heat. The best answer is
choice B.
6.
Choice C isthe best answer. The greatest amount oftime required to heat a solution will be found with the solution having the greatest heat capacity combined with the slowest rate of heating. Choices A and B can be eliminated immediately, because they have lower heat capacities than choices C and Dwhile having all other variables equal. The resistors are equal in all of the choices, but the voltages differ. At higher voltage, according to V = IR, there is greater current through the resistor at higher voltage. With greater current the solution in choice D heats faster than the solution in choice C. Keep in
mind that we are looking for the longest heating time, so we are looking for the slowest rate of heating. The bestanswer is
choice C.
7.
Choice C isthebest answer. In parallel, the reciprocal ofthe equivalent resistance equals the sum of the reciprocals ofeach resistor in parallel, so choice A is a valid statement and thus eliminated. In parallel, the voltage drop is equal, but the
currents are different As a consequence, choices B and D are also valid statements. This eliminates choices B and D and
leaves choice C as the lone choice standing. The power drain isV2/R, which means that with different values for resistance,
the power drain through each resistor must also be different. Choice C is an invalid statement so it is the best answer. As a
point of interest, the resistor with less resistance drains more energy when they are aligned in parallel. This is the opposite of
what is observed in series. The best answer is choice C.
206
MINI-TEST EXPLANATIONS
Choice A is the best answer. In Circuit I, the two batteries are in series and aligned so that the overall voltage is the sum of Vj and V2. In Circuit II, the two batteries are in series and aligned so that the overall voltage is the difference between Vj and V2. That is to say that the two separate batteries oppose one another in Circuit II. This means that the overall voltage is
greater in Circuit I than in Circuit II, making choice A the best answer. This is true regardless of the resistors. The best
answer is choice A.
9.
Choice D is the best answer. Current flows from cathode to anode (opposite of electrical flow). V2 is greater than Vi, so the electrical current is dictated by V2. Circuit notation dictates that the longer line of the battery represents the cathode, so
current will flow in a counterclockwise fashion. This eliminates choices A and B. The resistors are in series, so the current
through each resistor is the same. Current varies when resistors are in parallel, because current has two pathways from which to choose. But when the resistors are in series, current has only one way to flow, thus it will have a fixed value (Itotal- The
best answer is choice D.
10.
Choice A is the best answer. We are talking about a series circuit that now includes an extra resistor, Rbattery- You can
imagine that the more resistors you have in series, the harder it is for the battery to push a current. Thus, this extra resistance
results in a slightly smaller current. The power drained by the resistors is: P=I2R
Thus, if the current, I, decreases a bit, then so will the power drained. Note that R in the equation does not change, because it is a property of the resistor itself, and not dependent on the circuit in which it is placed. The best answer is choice A.
11.
Choice B is the best answer. The formulas of interest are: V = IR and P = IV. CircuitV has the two resistors in parallel.
Resistors in parallel experience the same voltage drop, but not necessarily the same current. Thus, we should rewrite the power formula so that it contains only V and R (which is what we will use for the comparison.) Plugging Ohm's law into the
power equation gives:
12.
Choice B is the best answer. In Circuit VI, the two batteries are in series, so the total voltage is found by summing the individual voltages. This eliminates choices C and D. The two resistors are in parallel, so the reciprocal of the equivalent resistance is the sum of the reciprocals of each individual resistor. This eliminates choice A, leaving only choice B as a possible answer. To double check, you may either calculate the equivalent resistance, or verify the equation by observing the units. As shown, choice B will have units of Q for resistance, so the equation seems viable at a glance. As a point of interest, when there are two resistors in parallel, the equivalent resistance is their product divided by their sum. The best
answer is choice B.
13.
Choice A is the best answer. When two resistors are in series, the same current flows through both of the resistors. Electrical current is like water flow in that the volume moving is the same at any point in the path. When there is only one flow path, the same current must flow through every part of the path. Thus, both resistors must have the same current, making Statement I valid. When a circuit is wired in parallel, the current splits up, so current can flow more than one way. The current need not split up evenly. In fact, more current flows along the path of least resistance - like with water in a diverging river. This results in each parallel path having the same voltage drop (-IR).
In parallel, resistors share a common voltage. This makes Statement II valid. The voltage across each resistor and the battery is V. This is because a line can be traced from the top plate of the battery to the top of Rj without crossing any other electrical components. This means that the top of the resistor is at the same potential as the top plate of the battery. A line can also be traced from the bottom of Ri to the bottom plate of the battery without crossing any other components, so the bottom of R\ is at the same potential as the bottom plate of the battery. Since the voltage across the battery is V, the
voltage across both R\ and R2 must also be V. Resistors in parallel have the same potential V across them. Because Req is different in the two circuits, Ieq is also different, so the power drain (V-I) must be different. This makes Statement III
invalid. The best answer is choice A.
207
MINI-TEST EXPLANATIONS
14.
Choice A is the best answer. The total current will be greatest in the circuit with the greatest total voltage and the least
equivalent resistance. Equivalent resistance is minimized when circuits are in parallel. Circuits I and III are equal because
both have the two batteries in series and the two resistors in series. This eliminates choices C and D. The current in Circuit
II must be zero because the batteries are of equal voltage, and they oppose one another. The total voltage is the difference
between Vi and V2, which is zero. With zero voltage, the current must also be zero. This eliminates choice B and makes
choice A the best answer. Circuit IV has a low current because the batteries are in parallel (minimizing total voltage) and the resistors are in series (maximizing equivalent resistance). Circuit IV has less total current than Circuits I and III. The best
answer is choice A.
Circuit City
Choice D is the best answer. When circuit elements are in parallel, they share the same voltage difference. The three circuit
elements in this question (C, R2, and R3) are all side-bys-side and they share the same voltage drop, which means they are all
in parallel. A good way to check whether circuit elements are in parallel is to see whether their ends meet at common junction points. If we redraw part of the circuit:
I
R3
R2
II
we see that the two ends of each circuit element touch at points I and II. Thus, all three elements are in parallel. The best
answer is choice D.
16.
Choice B is the best answer A capacitor is a device that stores charge. When Switch 1 is first closed, the charges have not yet been pushed onto the capacitor. It takes a finite time for the charges to move onto the capacitor plates. Thus, immediately after Switch 1 is closed, the charge on the capacitor is zero, but it will begin to build up very soon thereafter. The best
answer is choice B.
17.
Choice B is the best answer. C and R3 are connected in parallel. Remember that initially, there is no voltage drop across the
capacitor (as there is negligible charge on it), which means that there is no voltage drop across R3 at the instant that Switch 1
is closed. This is to say that at the instant Switch 1 is closed, all of the current goes to the capacitor (following the path of
least resistance) rather than through R3. From Ohm's law: AV = IR. If there is no voltage difference, there can be no current
flow. When Switch 1 is closed, initially it is as though all we have is one battery and one resistor, Rj, connected in series.
Again, from Ohm's law:
e = I Rj, therefore I = E
R,
Note that R2 does not enter into consideration here. With Switch 2 open, R2 will not have any current flowing through it and
will not have a voltagedrop. With Switch 2 open, it is as though R2 were not there. The best answer is choice B.
18.
Choice A is the best answer. When the capacitor is negligibly charged, and a current is turned on in the circuit, almost all of
the current will flow toward the capacitor. The resistor offers resistance to the flow of current, but an uncharged capacitor
does not. Therefore, current will flow through the capacitor section of the circuit and not through R3. The best answer is
choice A.
19.
Choice B is the best answer. With just Switch 1 closed, R\ and R3 add in series. With Switch 2 closed, current can now
flow through the R2 path as well. Because R3 and R2 are connected in parallel, Req decreases for that segment of the circuit.
Therefore, Req for the entire circuit decreases. Resistors connected in parallel have an equivalent resistance that is smaller than either individual resistor; R2 and R3 connected in parallel produce an equivalent resistance that is smaller than R3 alone.
When this equivalent resistance is added to Rj, we get a resistance that is smaller than when just Switch 1 is closed. The best
answer is choice B.
208
MINI-TEST EXPLANATIONS
20.
Choice Dis the best answer. Since the two cars have the same initial kinetic energy, the work required to stop both cars is:
C= 0AV
Q = CAV
Since Cand R3 are connected in parallel, the voltage difference across Cis the same as the voltage difference across R3 (AV = I3R3 =1^3). After Switch 1 has been closed for a long time, the capacitor has become fully charged, and no more current
flows to the capacitor. This means that there is now a voltage drop across C (a maximum value), so there is a voltage drop
across R3. Since Switch 2 is still open, no current flows through R2. Thus, in determining the total current flowing in the
circuit, it is as though we have a battery connected to two resistors in series:
1vWA
Ri
v
R3.
Resistors in series add together to give an equivalent resistance of Rserjes = Ri + R3- Using Ohm's law, we can solve for the
total current in the circuit:
e ~ * ^series ==> * ~
R1 + R3
AV = IR3 => AV =
Finally, we use this voltage to solve for the charge on the capacitor:
-R3 R1+R3
Q= CER3
R1+R3
This answer can also be approached using a bit of physical intuition. Since Switch 2 is open, R2 will not figure into any
voltage drops or charge accumulations. Therefore, choice C can be eliminated. Choice A can be eliminated, because if current flows through the capacitor section at some point in time (as it does), then charge will accumulate on the capacitor. Choice B can be eliminated, because it says that the voltage across the capacitor plates is e. This is wrong, because there is a potential drop from the battery across Rj, which will lower the actual voltage across the capacitor. The best answer is
choice D.
21.
Choice A is the best answer. After the capacitor is fully charged, no current will flow into the section of circuit containing
the capacitor. That may make choices C and D seem correct-but those choices compare R2 to Ce, representing resistance and charge, respectively. Comparing unlike physical quantities is nonsensical, so choices C and D are incorrect. Between the two resistors R2 and R3, the smaller resistor necessarily must have more current flowing through it. Notice that these two resistors have the same voltage across them, as they are wired in parallel. So if R2 is to have more current than R3, R2 must
have the smaller resistance. The best answer is choice A.
Questions 22 - 25
22.
Choice D is the best answer. As the space between the capacitor plates is filled with a polar substance, the capacitance will increase. This eliminates choices A and C. Because the fluid is being added at a constant rate, the capacitance will change at
a constant (gradual) rate, not abruptly. The best answer is choice D.
23.
Choice B is the best answer. When the capacitor is fully charged, it will have some voltage across it, because it stores charge and it has a capacitance. This eliminates choice A. Recalling that Q = VC, vve know that V = Qmax'C, not C/QmaxThis eliminates choice C. Choice D has the wrong units, leaving only choice B. Regarding choice B, the capacitor should have the same voltage across it as the battery, because this circuit (battery-Rc-C) has no current flowing through it. Because no current flows through the resistor, there must be no voltage drop across the resistor; this leaves a voltage drop across the
capacitor equal to the voltage gainacross the battery (i.e., the emfof the battery). The best answer is choice B.
209
MINI-TEST EXPLANATIONS
24.
Choice C is the best answer. Capacitance is defined as: C = Q/V, where Q is the charge on the plates of the capacitor, and V is the voltage difference between the plates. The maximum charge therefore depends on option I and II only. There is no dependence on resistance of any kind. The best answer is choice C.
25.
Choice B is the best answer. As current is passed through a resistor, it heats up. The energy transfer must involve heat, so choices A, C, and D can all be eliminated. Energy is being transferred from the chemical battery to the resistors, so it starts with chemical potential. It goes through electric flow and eventually becomes heat. The best answer is choice B.
210
MINI-TEST EXPLANATIONS
I.
Basic Circuit
(i-6)
(7-12)
(13 -18) (19 - 22)
IV.
V.
Wheatstone Bridge
Pacemaker Circuit
(23 - 28)
(29 - 33)
RC Circuits
Resistance is Futile
MCAT Score
13-15 10-12 7-9 4-6
:.
42-52
34-41
24-33
17-23
1-16
1-3
3.
If all three resistors have equal resistances, which of the following statements is true?
C. R3 will have a larger current than either Ri or R2. D. Ri and R2 will each have a larger current than R3.
4.
9 watts 18 watts
36 watts 72 watts
5.
Figure 1
Rj = R2 = 2 R3 = 2 ohms
B. Vbattery = 9 volts, Itotal = 2 amps, and t = 1second C Vbattery = 6 volts, Itotal = 2 amps, and t = 2
seconds
In all questions that follow, ignore the internal resistance of the battery. The only resistance to consider is that of the resistors specifically shown in the circuit.
1.
2.
A. Req = Rj + R2 + R3
B.
Req =
R,
R, + R2
Rj +R2
Current (A)
Current (A)
C. Req - R3 +
eq
D. Ren =(RlHR2) +R
R, + R2
212
8.
A.
Benzene
B.
C. D.
Cyclohexane
Octane Water
Equation 1
9.
C = K'C,
where C is the capacitance, K is the dielectric constant, and C0 is the capacitance in a vacuum.
Qotal
Ci
Cn
B Qotal = + Ci Ch
C L- = Ci +Q]
Qotal D. Qotal = Ci + Cn
10.
Which of the following changes will NOT affect the capacitance? A. Increasing the distance between the capacitor plates. B. Filling the inter-plate region of the capacitor with a polar liquid. C. Changing the voltage source of the circuit. D. Changing the materials of the capacitor plates.
Figure 1
The coil has inductance of L henries, Q has variable
11.
Why might the solution into which Crj is dipped during the experiment be immersed in an oil bath that is fitted with a heating coil? A. Polarity of the solution may be fixed, but the heating coil is needed to maintain homogeneity. B. Temperature must be held at a fixed value, because the dielectric constant can vary with temperature.
2n YLfa + Ci,)
An experiment involves dipping Cn into various solutions and measuring the change in capacitance, by monitoring the frequency of the circuit. The change in capacitance is determined by the dielectric constant (K) for
each solution. This constant is always equal to or greater than
one. As a general rule, more polar compounds have greater values of K than nonpolar compounds.
12.
7.
Which of the following changes will decrease the naturalfrequency of the circuit by a factor of 2?
C. By measuring the change in inductance. D. By measuring the change in the resonance frequency of the circuit.
213
15. How do the values for the equivalent resistance in each of the three systems compare?
System I
=r V
A. B. C. D.
Req System I> Req System II > Req System III Req System III > Req System II > Req System I Req System II > Req System I > Req System III Req System III > Req System I> Req System II
Ri^J1
System m
l2gR2
A. B. C. D.
Requivalent varies in System II only. Requivalent varies in System I and System IIIonly. Requivalent varies in System II and System III only. Requivalent varies inSystems I, II, and III.
TV
r4I2|%J|i3
Figure 1
B.
C.
72 Watts
D.
108 Watts
18. What is the equivalent resistance for the circuit shown as System II in Figure 1?
A. 0.56 Q
B.
3.67Q
A. Ri upperleft, R2 upper right, and R3 bottom B. R2 upperleft, Rj upperright, and R3 bottom C. R2 upper left, R3 upper right, and Ri bottom
D. R3 upper left, Ri upper right, and R2 bottom
C.
D.
4.50 Q
6.00 Q
214
I. If the two resistors are connected in parallel, then they experience thesame voltage drop.
II.
A. B. C. D.
From kinetic energy to potential energy From potential energy to kinetic energy From heatenergy to electrical energy From electrical energy to heat energy
III.
If the two resistors are connected in series, then they have different currents flowing through them. The two resistors will experience the same power
drain, whether they are connected in series or in
parallel.
A.
B.
C. D.
discharging capacitor is given by T = RC, where R is the total resistance of the circuit and C is the capacitance of the circuit. If a third resistor were added in parallel to Ri and R2, what would happen to the time constant of the
circuit?
B.
21.
An ammeter measures the current that passes through a particularregion in a circuit With respect to any circuit
whose current it measures, the ammeter should have a:
215
24.
The wire between Points a and c is made of a uniform materia] and has a uniform radius to ensure that the:
resistance, a resistor of unknown resistance, a galvanometer, and a voltage source. Figure 1 shows a wheatstone bridge.
A. relative resistances of segments AZ and ZC only depend on their respective lengths. B. relative resistances of segments AZ and ZC only
depend on their respective cross-sectional areas. C. relative resistances of segments AZ and ZC are equal to one another.
*& ^ i
"kh 7
Figure 1 Wheatstone Bridge Circuit
A. Either Ri, R2, or R3 must be a variable resistor. B. Ri must equal R3 for the circuit to work.
C. The galvanometer should be able to measure both
magnitude and direction.
D. The circuit will exhibit the same results when the
If the voltage across the galvanometer, G, is zero, then the voltage drop across Ri is equal to the voltage drop across R2- If this is true, then the following applies:
'lRl ='2R2 and qR3 = /2R4
Rj_ = R2 ., R4 =(R2XR3)
26.
C.
D.
PMetal III > PMetal I > PMetal II PMetal III > PMetal II > PMetal I
If the voltage of the battery were doubled, how would the position of Point z change?
A (4-zX4-c)
B.
Rknown Rknown
(4a-zX4-c)
C Rknown
Oz-c
C. The distance between Point z and the midpoint of wire AC would increase bya factor of V2. D. The distance between Point z and the midpoint of
wire AC would remain the same.
D- Rknown^,
4i-z
216
30.
The beating of a human heart is a regulated cycle of cardiac muscle contractions. A group of specialized cells in the right atrium of the heart acts as a pacemaker and begins each cardiac cycle by generating automatic and rhythmic action potentials that spread throughout the organ. For those people whose natural pacemaker fails to work properly, an artificial pacemaker may help. An artificial pacemakeris two RC (resistor-capacitor) circuits joined together. The capacitor is repeatedly charged and discharged. The basic pacemaker
circuit is diagrammed below:
C. D.
60: 1 23 : 1
31.
HVW
R
aQQ
circuit
Time
Time
to the left (as shown), the capacitor is charged through Rc (the charging resistance). The switch then changes position and the capacitor is discharged through R<j (the discharging
of a triggering circuit deliver a short pulse of current to the heart. The time to charge the capacitor is typically much longer than this pulse and is approximately equal to the natural time between heart beats. Some pacemakers operate at a fixed frequency, while others operate only if the patient's
own heart fails to do so.
Time
Time
32.
An important parameter used in characterizing an RC circuit is the time constant, T, which obeys T = RC, where R is the resistance (in ohms) and C is the capacitance (in
farads). After one time constant has elapsed as the capacitor charges, the current in the circuit has dropped to 0.37 times
29.
Ignoring the discharging part of the circuit, one would conclude that the maximum potential difference across
Rc occurs:
For the above artificial pacemaker, suppose that pulses are triggered 60 times per minute by a 5-mF capacitor. What is the time constant of the charging RC circuit? (Neglect the time needed to discharge the capacitor.)
A. B.
C. D.
A. immediately after the switch is closed. B. after a long time has elapsed. C. at the same time that the maximum potential difference occurs across the capacitor plates. D. after the maximum potential difference across the capacitor plates is reached.
217
34. How are the electrical outlets in a typical home hooked up?
A. In series
IA
B. In parallel C. In a combination of both series and parallel D. Neither in series nor in parallel
2A
4A
WW'
1A
2Q
wvw^'
R3
A.
B.
2V
4V
C.
D.
8V
12V
I. The current passing through a conducting wire in the presence of an electric field is zero.
II. Resistors provide electrical energy to a circuit
III. The amount of current leaving a resistor is smaller than the amount of current entering a resistor.
IV. The current leaving the cathode is equal in magnitude to the current arriving at the anode.
A. I only B. I and III only
C. I, II, and III
D. IV only
36.
Which of the following observations are valid? I. If resistors are aligned in parallel, rather than series, then the equivalent resistance will be less.
II. When two resistors are aligned in parallel, the current through the resistor of higher resistance is
greater than the current through the resistor of
lower resistance.
III. Only resistors that are aligned in parallel will increase in temperature as current passes.
A. I only
218
inserted into the circuit before switch Si, then the maximum charge that could be stored on the capacitor
would:
R2.
Figure 1
A. 2 x lO'8 C B. 2 x 10"4 C
C. 5xl06J
C. 5xlO-3C D. 2x10'^
D. 5xl0"5J
39. If the capacitor were initially uncharged, it would be true that when both switches are closed simultaneously,
the voltage across the capacitor:
43. Which graph accurately depicts the charge of a capacitor over time as it is discharging voltage?
A. B.
Time C.
D. would shoot up rapidly and then decrease, while the current through the resistors decreases.
40. A long time after both switches are closed, the current through resistor Ri is:
A. B. C.
D.
Time
Time
2 mA. 50 mA. 2 A.
50 A.
219
R2
r^A/W
Switch
WWH
VVW-
generator. The charges do not move straight through the wire, butrather proceed fromone end of the wireto theother along jagged paths. Thecharges suffermany collisions on the way and lose energy. The resistance of a conducting wire,
measured in ohms, is a measure of how difficult it is for the
R3
charges to move through that conductor. Ohm's law relates the loss of potential by the current, AV (measured in volts),
to the resistance, R, by the equation AV = IR, where I is the
current measured in amperes (or amps).
Battery
main source of a high resistance is due to resistors. The purpose of a resistor is to control or modify the current throughthe circuit Resistors typicallyobey Ohm's law. There may be several resistors in the same circuit Resistors can add together in one of two ways: in series, where the effective resistance is given by:
Reff = Rl + R2 + ...
B. C.
D.
decreases,
is unaffected.
undergoes a changes that depends on whether R5 is less than or greater than (Ri + R2).
47.
Birds can be seen perched on high-voltage power lines, yet they seem unaffected by the high voltage. This is
due to the:
R eff
--L + .L+... Rl R2
A. low resistance of the birds compared to the wire, minimizing the current through the birds. B. birds keeping only one foot on the wire, thus not making a complete circuit C. low capacitance of the birds. D. minimal potential difference across the birds.
i-wvw
Switch 1
Switch 2
CQ
parallel with the section. When both switches are closed, as compared to when just Switch 1 is closed, the:
A. total resistance of the circuit is unaffected.
45.
Light bulbs, such as holiday lights, can be strung together in series or in parallel. How should these bulbs
be connected so that if one bulb burns out the other
bulbs remain unaffected? A. In series.
B. total resistance of the circuit is larger. C. voltage drop across Ri is larger. D. power drain in the circuit is larger.
B. C.
220
52.
R2
r-vW-i
R4
Rl
rWWVH
WWR5
Ii is definitely greaterthan I2 I2 is definitely greater than I3 I3 is definitely greater than I4 I4 is definitely greater than I5
Ri=4Q
R2 = 2Q
rn/VWI
LyvV\M
A.
1.
2. 8. 14.
20.
D
D
3. C 9. D 15. A
21. C 27. B
4.
10.
D C
5. D
11. B 17. B
23. D
6.
12. 18.
24.
B
D B
A
7. D 13. C
19. D
C
D
16. A
22.
C
A A B
A
D
B
29. A
30.
33. C 39. B
45. B
35. D
41. D 47. D
36. A
42. B D
C C
48.
51. C
52. D
221
Choice C is the best answer. The current flowing through any resistor depends on the total current, the voltage drop across
the resistor, and the resistance of the resistor in question. The voltage does not change in the question, so the resistance of Ri
and the total current I must be considered. In choice A, the resistance of R\ has increased, so the current through that resistor
II must decrease. This eliminates choice A. In choice B, the equivalent resistance of the circuit has increased, because Req
must increase as R3 does. Because V = (I)-(Req), the total current will decrease. IfItotal decreases, then all currents l\, I2, and
I3 must decrease. This eliminates choice B. To determine the effect on l\ when R2 changes, given that the change in R2 is
compensated for by a changing R3 (so that Req of the entire circuit does not change), you must apply Kirchhoffs junction
rule: I = Ij + I2.
If Rj is equal to R2, II must also equal I2; if Ri is less than R2, then \\ must be greater than I2. This is to say that current
follows the path of least resistance. Increasing R2 will decrease I2; and since Itotal >s constant (V and Req have not changed,
so Itotal must he the same), the value of Ij must increase. The best answer is choice C. Choice D is the best answer. The first step involves adding R\ and R2, which are in parallel.
1 _ R-
R,
R, + R-i
_ (Ri)(R2)
Rj + R2
" R,1
R^2
Ri)(R2) (Ri)(R2)
(*i)(J
+ R,
_ (Ri)(R2 Req = R + R3 = Rj + R2
The voltage information is useless without also knowing the total current in the circuit. Also, you should note that you could have used your shortcut of knowing that for two resistors in parallel, their equivalent resistance the the product of the two resistors divided by the sum of the two resistors. Take shortcuts wherever possible. The best answer is choice D.
Choice C is the best answer. We are asked to consider the amount of power drain by the current flowing through each resistor. Current will flow from the battery, split up and move through R\ and R2, recombine and move through R3, and
finally return to the battery. Therefore, R2 will have the largest current, making choice C correct. Choice B is incorrect, because identical resistors in parallel should have the same current, and therefore the same power drain. Choice A is
incorrect, because R3 has the largest current, making I^R biggest for R3. Choice D is incorrect, because it contradicts choice
C. The best answer is choice C.
Choice D is the best answer. The question gives you the total current and the equivalent resistance, so the power equation of
choice will include I and R. Recalling that P = I2R, where P ispower, I is current, and Ris the resistance, we find:
Choice D is the best answer. First, you must recall that Energy = (Power)-(time). In other words, E = Pt = V-I-t. This means that the greatest energy will be dissipated in the choice that yields the greatest product of voltage, current, and time. Choice C is eliminated, because choice A has the same voltage and time, but it has a greater current. Choice B is eliminated, because it has a smaller voltage, current, and time than choice D. Choice D yields more energy than choice A, because although they have the same current, choice D has a greater voltage and a longer operating time. The energy dissipated in choice D is 48
joules. The best answer is choice D.
Choice B is the best answer. The power of the circuit is found using the equation P = VI. Because the voltage is held constant, we can conclude that PI. The graph for this is a linear relationship with a positive slope, so choice B is the best answer. Choices A should be eliminated because of the increasing relationship between power and current, which doesn't
match a linearly decreasing graph. It may be tempting to consider choice C, because P = I2R; but with V held constant, R
must decrease with an increase in I. This means that the power has term increasing by a square factor coupled with another term decreasing in inversely, which once again points to a linear relationship between P and I. Choices C and D should be
eliminated. The best answer is choice B.
222
Dielectric Experiment
Choice Dis the best answer. This question requires using the equation given in the passage. According to the equation the natural resonance frequency v0 is inversely proportional to the square root of L, the inductance, and the square root of the sum of the two capacitors. Increasing the variable capacitor by afactor of 4does not increase the sum (Ci +Cn) by afactor of 4, so the natural resonance frequency is not cut in half. This eliminates choice A. Increasing both Cr and Qi by afactor of
natural resonance frequency by a factor of 2. Choice Cis thereby eliminated, leaving only choice D. The best answer is
choice D.
2does increase the sum (Ci +Cn) by afactor of 2, but this will decrease the natural resonance frequency by afactor of V2, not by afactor of 2. This eliminates choice B. The inductance Lof the coil must be increased by a factor of 4 to reduce the
Choice Dis the best answer. The most polar substance will exhibit the greatest value for K, the dielectric constant. This is
to say that the molecules of a polar material can align themselves within the electric field between the plates of the capacitor
current to flow, to reestablish the maximum plate charge. The more polar the material, the more the capacitance will change. This means that the best answer is the most polar substance. Benzene, cyclohexane, and octane are all nonpolar (organic)
compounds, so choices A, B, and C can be eliminated. The best answer is choice D.
and in doing so reduce the effective plate charges. This reduces each plate's repulsion to current, which in turn allows more
Choice Dis the best answer. Choices Band Cshould be eliminated immediately, because two sides of the equation have inconsistent units (one side is in Fand the other is 1/F). This leaves choices Aand D. The two capacitors (Cj and Cn) are in
Remember: Ctotal s Q +Cn, in parallel, because it's similar to make a wider capacitor, and wider capacitors (like plates in
general) can store more stuff. The best answer is choice D.
10.
parallel, so according to circuit convention, their capacitances are added together. This makes choice D the best answer.
Choice Cis the best answer. Increasing the distance between the charged plates affects the strength ofthe electric field, and thus, it affects the plate charges that can be developed. This means that the distance between the plates affects the capacitance. Choice A is eliminated. The whole idea behind the passage is to study the effect of adding a solution to the space between the two plates of acapacitor, so choice Bcan be eliminated. No matter what voltage source is chosen-battery, inductance coil, or any other incident current source--the capacitor has a maximum amount of charge that it can store. This means that the voltage source of the circuit does not affect the capacitance, so choice C is the best answer. Changing the
charge may be stored on the capacitor. This eliminates choice D. The best answer is choice C.
material of the plates definitely affects the amount of charge that can be stored. For instance, if an insulator is used, then no
11.
Choice Bis the best answer. The oil bath and heating coil unit keeps the solution at aconstant temperature. The heating coil
does not affect the homogeneity of the solution, so choice A is eliminated. Because the density of the solution varies with temperature, the amount of solution that fits between the plates can vary with temperature. In addition, entropy increases
with temperature, so the molecules ofthe solution will not align as well at higher temperatures. These effects will change the
dielectric constant, making choice B the best answer. Heating the circuit adds energy to the circuit, but not in the form of current. This eliminates choice C. Resistance is observed to increase at higher temperatures. Even if you did not know this, you should not assume that it would decrease at higher temperatures. Either way, choice D is not the best answer. The best
answer is choice B. 12.
Choice D is the best answer. The current does not flow through a capacitor, meaning choice A can be eliminated. Capacitors store energy in the form of charge buildup, which is caused by current. The currents generated by the stored electrical energy are never observed in this experiment. Therefore, the amount of current flow the capacitors can induce while discharging is irrelevant. This eliminates choice B. The inductance is held constant, because the coil does not change during the experiment. It is not mentioned how the current from the adjacent circuit (flowing through the other coil of the transistor) is altered, so choice Cshould be eliminated. The only measurement mentioned in the passage (that is also offered
among the answer choices) is the natural resonance frequency of the circuit. As Cn changes, the value of the natural resonance frequency of the circuit will change. The change in resonance frequency is observed, recorded, and then converted into the change in capacitance experienced by Cn. This makes the best answer choice D. The value of Cn can be found as
follows:
C,i =
231V.
L
-C,
where L and C\ are constant, and v0 is measured. The best answer is choice D.
223
Resistor Alignment
Choice C is the best answer. The greatest total current is found in the circuit with the least equivalent resistance.
Equivalent resistance is minimized when the larger resistors (the resistors with greatest resistance) are in parallel and the
smaller resistor (the resistor with the least resistance) is in series. You can use math to verify that this is true in the case of
three resistors with resistances of 1Q, 2Q, and 3& respectively. If the 1Q resistor is in series and the 2Q and 3Q resistors are
in parallel with one another, then the equivalent resistance is 1+(2 V/(2 +3) = l +6/5 =2 f5- If tne 3^ resistor is in series and the 1Q and 2Q resistors are in parallel with one another, then the equivalent resistance is 3+0 2)/(j +2) =3+
2/~ - 32fy This means that the arrangement with R\ in series, and R2 and R3 in parallel minimizes equivalent resistance,
and thus maximizes current. For maximum current, R) must be at the bottom, which is only true in choice C. Note that
upper left and upper right resistors can be interchanged, and the equivalent resistance will not vary. This means that choices
A and B are the same answer. The best answer is choice C.
14.
Choice C is the best answer. The key values they give us are the circuit's equivalent resistance and the its voltage. From these values, Ohm's law tells that the current must be V/R, which is 12/4 = 3 amps in this case. From here we can note that I3
is also 3 amps and that Kirchhoffs junction rule tells us that: Itotal = Ii + Pi- If *1 = 2 amps, then I2 must be 1 amp. This tells
us early on that choice C is the best answer.
But let's consider the other choices to be complete. First off, we have determined that h is 1 amp and are given that \\ is 2
amps, so Ii is greater than I2, which eliminates choice D. If 11 is greater than b, then R\ must less than R2 given that they share the same voltage drop (-IR). This eliminates choice A. The equivalent resistance is found by adding the parallel resistance to R3, so it is not possible that R3 could be 4 Q if the equivalent resistance is 4 Q. Choice B is also eliminated.
The best answer is choice C.
15.
Choice A is the best answer. There is a general rule that states that the equivalent resistance is minimized when the resistors are placed in parallel. This would make choice A the best answer at initial glance, because in System III, all three resistors are in parallel. In System II, only two resistors are in parallel, and finally in System I, all of the resistors are in series. But to solve this thoroughly, it is necessary to identify the different circuits. In System I, the resistors are in series, so
Req = Ri + R2 + R3 = 6Q.
In System II, R\ and R2 are in parallel, so the are summed in the following manner.
1 _ 1 + 1 _ R2
+ Ri
_ Ri +R2 . Ra|-(Ri)(R2)
R1+R2
To obtain Req for System II, the value of Rpar (for Rj and R2) must be added to R3, which is in series:
In System III, R\, R2, and R3 are all in parallel, so the equivalent resistance is found as follows:
Ri
R2
R3
(R1XR2XR3)
16.
Choice A is the best answer. When all three resistors are in series, as is the case in System I, the equivalent resistance is
found by summing the individual resistors. No matter how the three resistors are sequenced, the sum is the same. This means that in System I, the equivalent resistance does not vary with sequence. When all three resistors are in parallel, as is the case in System III, the reciprocal of the equivalent resistance is found by summing the reciprocals of the individual resistors. No matter how the three resistors are sequenced, the result is the same. This means that in System III, the equivalent resistance does not vary with sequence. This leaves only System II, which makes choice A correct by process of elimination. Because System II has two resistors in parallel and each of those in series with a third resistor, the sequence impacts the equivalent resistance. The equivalent resistance for the two resistors in parallel is found by taking their product and dividing that number by their sum. This is the mathematical fallout from the relationship between the reciprocal of the equivalent resistances and the sum of the reciprocals for the two resistors. The equivalent resistance for the entire circuit is found by summing the parallel equivalent resistance and the third resistor. All of this bombastic banter simply confirms that for System II, finding the equivalent resistance is a pain in the butt. . The best answer is choice A.
224
17.
IV, P=I2R, and P=V2/R, where Pis power, Vis voltage, Iis current, and Ris the resistance. In this question, we are given
only V and R, so to determine the power, vve should use P = V2/R:
Choice Bis the best answer. There are three versions of the equation for the power drained by a resistor in a circuit: P=
Choice Bis the best answer. To determine the equivalent resistance, we should start by determining the parallel equivalent
resistance for R\ and R2 combined. Because there are two resistors are in parallel, it is easy to use the shortcut that the equivalent resistance (Req) equals the product of the two resistors divided by the sum of the two resistors.
1 _ 1
1_
R2
Rl
Rpar Rl
This leads to a parallel equivalent of (1 x 2)/(l + 2) = 2/3 = 0.67 Q. Now to determine the overall equivalent resistance of the
entire circuit, we need to add the parallel equivalent to R3, because they are in series.
Questions 19 - 22
19.
Choice D is the best answer. When current is passed through a resistor, the resistor heats up. This means that the energy
transfer of the system must involve heat, so choices A and B can be eliminated. Overall, energy is being transferred from the battery to the resistors. Thus, the best answer is that their electrical energy is being converted to heat energy. The-best
answer is choice D.
20.
Choice D is the best answer. The characteristic time that it takes for a capacitor to discharge through a resistance is called the time constant of the circuit. The time constant of a discharging capacitor is given by T = RC, where R is the total resistance of the circuit and C is the capacitance of the circuit. If a third resistor were added in parallel to R\ and R2, then the
resistance of the circuit would change, which would change the time constant of the circuit. Whenever we add a resistor in parallel, the total resistance of the circuit always decreases. This eliminates choices A and B. Since R decreases, the time constant must also decrease. What this means physically is that a capacitor discharges faster when there is less resistance in the circuit. That should seem physically intuitive, given that less resistance would allow the charge to leave the plates faster and thereby take less time to completely dissipate. The best answer is choice D.
21.
Choice C is the best answer. To measure current flowing through a particular part of a circuit, the ammeter must be connected in series, so that the current can flow through it. This eliminates choices B and D. In order to facilitate this, without disrupting the current flow much, the ammeter should have a small internal resistance compared to the circuit of
interest. The best answer is choice C.
22.
Choice A is the best answer. When the resistors are arranged in parallel, then there are two different pathways current may
take from the cathode to the anode. Both pathways must result in the complete drain of voltage, so each parallel pathway experiences a voltage drop equal to the voltage of the battery. Although a different current will flow through each of the resistors, they will experience the same voltage drop, which is equal to I x R. Statement I is valid, which eliminates choices
B and D.
When the resistors are wired in series, then the current that passes through one must also pass through the other. There is only one possible path, so the current is the same through each resistor. This makes Statement II invalid, which doesn't really help out with our process of elimination pathway.
In parallel, resistors share a common voltage. But because they have unequal resistances, they must have unequal currents. If we use the fundamental power equation, P = IV, then we see that the resistor with lower resistance, and thus higher current, will drain the more power. In parallel, smaller resistors drain more power than bigger resistors. In series, resistors have a
common current. If we use the power equation P = I2R, then we see that the resistor with higher resistance will drain more
power than the resistor with lower resistance. In series, larger resistors drain more power than smaller resistors. The power drain for the two resistors differs when they are wired in series versus when they are wired in parallel, which makes
Statement III invalid. The best answer is choice A.
225
Wheatstone Bridge
Choice D is the best answer. The passage provides us with math to reference if we so choose. If we assume that the unknown resistor, Rtj in Figure 2, is equivalent to R4 in Figure 1, then we simply need to match the corresponding resistors
in Figure 1 to those in Figure 2. The AZ segment of wire AC equates to R\, the ZC segment of wire AC equates to R3, and
the known resistor, Rknown. equates to R2. Given that R4 is equal to (R2)(R3)/Ri in Figure 1, vve can conclude that Rij in Figure 2 is equal to (Rknown)(dz-c)/da-z- This makes choice D the best answer. If you prefer, then the math can be solved as
follows.
n(p\vireAC
'lRz-c _
'lRa-z
dz-c
^wireAC / _ ^RlJ
'2Rkno\vn
*'2RU
'2Rkr
dz-c _
4-z
Rij
Rkr
- - k:::illa|4*
n(PwireAC)
4-z
wrwireAC2/
You could have also solved this by inspection. We know that in a wheatstone bridge, the voltage drops through the first resistor are equal in both pathways and that the voltage drops through the second resistor are equal in both pathways. So, the ratio of the first voltage drop-to-the-second voltage drop is the same in each pathway. Given that current is constant in each pathway, we can simplify the relationship to be that the ratio of the second resistor to the first resistor is the same for each
pathway. The ratio of Rij-to-Rk is equal to the ratio of Rz_c-to-Ra-z, which reduces to dz.c-to-da.z. Multiplying each ratio
by Rk results in choice D. The best answer is choice D.
24.
Choice A is the best answer. The resistance of a cylindrical segment of wire depends on the resistivity of the material, p, the length of the wire, and the cross-sectional area of the wire. In Figure 2, the wheatstone bridge functions by having a slide-wire capable of moving in such a way that wire AC is broken into two segments, AZ and ZC. The ratio of the resistancesof the two segments of wire (AZ:ZC) is equal to the ratio of the two resistors (Rknown:Runkno\vn)- If the wire AC is uniform in terms of material, then the resistivities of the two wire segments are equal. If the wire AC has a uniform radius, then the cross-sectional areas of the two wire segments are equal. The differences in the resistance between the two segments of the wire are due exclusively to the differences in their lengths. This makes choice A the best answer and eliminates choice B. The resistances of the two segments of wire do not need to equal one another, so choice C is eliminated.
The resistances of the two segments of wire do not need to be equal to the resistance of the unknown resistor, especially
since that resistance is an unknown value. Choice D is eliminated. The best answer is choice A.
25.
Choice B is the best answer. There must be a variable resistor amongst the three permanent resistors tooffset the variability
associated with an unknown resistor. If R4 represents the unknown resistor, then the variable resistor can be R\, R2, or R3, although it is best in the position of R3. This eliminates choice A. R\ does not need to equal R3, because that would mean that R2 must equal R4 for the galvanometer to read zero. This means choice B is not necessarily true of a functioning wheatstone bridge. Choice B may be the answer. The galvanometer needs to measure the magnitude of voltage difference
between the two sides so that adjustments to the variable resistor can be made to in turn vary the currents, i\ and *'2. enough to get the voltage drops through the first resistor of each parallel pathway to equal one another. The sign of the voltage
difference is needed to know whether to increase or decrease the resistance of the variable resistor. The galvanometer should
be able to measure both magnitude and direction, which makes choice C a valid statement. This eliminates choice C. No
matter which direction the current flows, the ratio of the resistances needed to generate a wheatstone bridge circuit with equal voltage drops in the respective regions of the parallel pathways does not depend on the magnitude of voltage. The circuit
exhibits the same results when the poles of the battery are reversed, so choice D is a valid statement. This eliminates choice
D. The best answer is choice B.
26.
Choice C is the best answer. A galvanometer, as the name implies, measures the voltage (galvanic emf) of a circuit. It supplies no voltage to the circuit, so choice A is eliminated. In the wheatstone bridge, we need to make sure that the voltage drops across the first resistor in both of the parallel pathways are equal. If the voltage drops are equal, then the voltage at Point b is equal to the voltage at Point z. The galvanometer connects points b and z, so it measures the potential difference between the two points, not the absolute potential at each point. This eliminates choice B and makes choice C the best answer. The galvanometer is used to ensure that the potential difference between Points b and z is zero. The galvanometer
does not serve as a short circuit (path of zero resistance). Even if it did, such a feature is not needed in the wheatstone
bridge. This eliminates choice D. The best answer is choice C.
226
27.
Choice Bis the best answer. It is not specified in the question, but vve can assume they are asking about the wheatstone
bridge in Figure 2. With Metal I constituting Rk and Metal II constituting Rij, Wire segment AZ is shorter than Wire
segment ZC. This means that the resistance of Rk must be less than the resistance of Rij. Given that the two resistors have
for the two metals. The metal with lower resistivity will correspond to the resistor of lower resistance. From this, we can
the same dimensions but are made of different metals, the difference in resistance must be due to a difference in resistivity
conclude that Metal I must have a lower resistivity than Metal II. From this point we can reason that Metal HI must have a
lower resistivity than Metal I, by virtue of the slide-wire now being closer to Point c than Point a (when Metal II is replaced to eliminate choices Aand D, because Metal I must lie in the middle, given its opposite behavior in the two trials. Honing
your process-of-elimination skills is an asset. The best answer is choice B.
28.
by Metal III). This makes choice B the best answer. Even ifyou are uncertain or not reasoning clearly, you should be able
Choice D is the bestanswer. If the voltage of the battery were doubled, the current would increase, which in turn would increase the voltage drop across each resistor. However, the resistance of each resistor would remain unaffected, because resistance depends on the resistivity and dimensions of the resistor, not the voltage of the battery. This means that the ratios of the resistances would remain unchanged, and therefore the ratio of the wire segments would not be affected. This
eliminates choices A, B, and C. The best answer is choice D.
Pacemaker Circuit
29.
Choice A is the best answer. The capacitor is initially uncharged. Immediately after the switch is closed to begin the
charging process, the currentbegins to flow. Charge has not yet built up on the capacitor, so there is a maximum amount of current in the circuit. By Ohm's law, the potential difference across the resistor is given by: AV = IR. If the current is at a maximum, then the potential difference is at a maximum. Choice B is incorrect: As time goes on, charge builds up on the
capacitor, so there is less current in the circuit. After a long time, there is no current in the circuit. Choice C is incorrect: If
the potential difference is maximal across the capacitor plates, it should be minimal across the resistor, because the voltage drop across both of them should equal the emf of the battery. Choice D is incorrect: Current flows before charge builds up completely on the capacitor, so the maximum potential difference across the resistor occurs before the maximum potential
difference across the capacitor. The best answer is choice A.
30.
Choice C is the best answer. The relationship between the charge time and the resistance is given in the passage as T = RC. The ratio of Rc : Rd will therefore be equivalent to Tc : Td. Using the charging and discharging times in the question
indicates that the best answer is choice C. The best answer is choice C.
31.
Choice A is the best answer. During one complete cycle of the system, the capacitor must start and finish at the same point, which eliminates choice B. Choice B can also be eliminated because it is linear in nature. Charge on a capacitor builds up on
the capacitor's plates exponentially, indicated in the passage by the repeated appearance in the charge equation of e"1, the
inverse of the natural log e. When a capacitor discharges, the charge drops rapidly at first and then gradually decreases until it reaches zero. This is expressed in the first half of the graphs in choices A and D. Choice C depicts a slow discharge at first that increases until an abrupt zero. This eliminates choice C. The capacitor fills rapidly at first and then slows until it reaches a maximum charge. This is expressed in choice A. Choice D shows the opposite in the second half of the graph. The best
answer is choice A.
32.
Choice A is the best answer. We want the capacitor to discharge much more quickly than the time between these discharge "heart beats." This would favor choices A and B over C and D. The resistors play a role in this discharge time, as T = RC.
Therefore, the resistance Rd should be relatively small compared to Rc. The best answer is choice A.
33.
Choice C is the best answer. If pulses are triggered 60 times per minute, that means there is one pulse triggered every
second. From the passage, we know that a pulse is triggered each time the charge on the capacitor drops to e"1 of its
maximum value, which corresponds to the time constant. Therefore, the time constant for this circuit is 1 second. The capacitance provided in the question is extraneous information. The best answer is choice C.
Questions 34 - 37
34.
Choice B is the best answer. The passage states that an example of a parallel circuit is the wiring in apartments. An
apartment is a home (assuming you like your roommates) so a home is "wired up" in parallel. Another way to tell that this is the best answer is the following: All of the components of a parallel circuit have the same voltage across them. In your home, all of the outlets have the same voltage. Thus, your house's circuits must be in parallel. If outlets were in series, then every time someone turned on an appliance, any other appliances that are already operating would experience a drop in power. The
best answer is choice B.
227
35.
Choice D is the best answer. One method of inducing current flow is to apply a voltage difference across a conductor, creating an electric field across it. Thus, if an electric field is present, current can flow. This makes Statement I and invalid
statement, which eliminates all of the answer choices except choice D. Sometime you get lucky like this. Resistance in the conductor will tend to slow down the charges, draining energy from the system as the current flows through them. Resistors
do not supply energy to a circuit. In fact, resistors are responsible for taking energy out of a circuit. This makes Statement zll
an invalid statement, which vve already suspected based on our elimination of choices A, B, and C. As has already been stated, increased resistance in a conductor means more interactions between charges. Because of such interactions (i.e., collisions), resistors convert electric potential energy to heat. The amount of current passing through a resistor is unaffected by the resistor. Only the energy of the current is affected. Statement III is invalid, which again vve suspected. All of the electrons that leave one terminal must arrive at the other terminal, so vve can conclude that the current leaving the cathode is equal in magnitude to the current arriving at the anode. This is supports the notion that current is the same for all circuit
elements in series. Statement IV is in fact valid. The best answer is choice D.
36.
Choice A is the best answer. Statement I is valid, because resistors in series sum directly, while resistors in parallel sum as reciprocals. For instance, three resistors in series have an equivalent resistance of R\ + R2 + R3, while in parallel, the equivalent resistance is less than each of the individual resistors. This makes Statement I valid. Based on the relationship, V
= IR, as resistance increases, the current must decrease, when the voltage is constant. For resistors in parallel, the voltage
across each resistor is the same, so the resistor with the greater resistance has the lesser current. This makes Statement II
invalid, which eliminates choices B and C. All resistors will heat up when current passes, making Statement III an invalid
statement. The best answer is choice A.
37.
Choice B is the best answer. The voltage drop across R3 is the same voltage drop experienced by all three parallel resistors. To solve this question, vve can apply Kirchhoff's loop rule. All 12 volts must be lost when charges travels from the cathode to the anode. Because 8 volts are lost across the series resistor (4A x 2Q = 8V), the parallel resistors must each drop 4 volts.
The voltage drop across R3 is 4 volts. The best answer is choice B.
RC Circuit
38.
Choice A is the bestanswer. Once Switch S\ is closed, the current will flow until the capacitor iscompletely charged. The charge and voltage on a capacitor are related through Q= VC. Plugging in the numbers from the passage gives:
Q = VC = (2/<F)(10mV) = (2xlO-6)(10x 10"3) = 20x 10"9 = 2x 10"8C
The best answer is choice A.
39.
Choice B is the best answer. If both switches are closed simultaneously, assuming the capacitor were initially uncharged, the circuit would include a capacitor in parallel with two resistors. When the switches are closed, the initial surge of current will go exclusively to the capacitor (which is the path of least resistance). But over time, the capacitor will build up charge. When charge builds up on a capacitor, so does the voltage across itremember: Q = VC. This eliminates choices C and D, which describe the current across the capacitor, not the voltage difference. When the switches are closed, the current through
the resistors starts at 0 and builds up to some maximum value given by V = IR. The best answer is choice B.
40.
Choice C isthe best answer. A long time after both switches are closed, the current will travel exclusively through resistor
Rl, because the capacitor passes no current once it is fully charged. To calculate the current through Rj, vve use Ohm's law,
V = IR. Plugging in the appropriate values, vve get 10 mV = 1(5 mQ), or:
I = iOmV = 2A
5 mQ
41.
Choice D is the best answer. If another resistor were inserted into the circuit before switch Si, then it would be in series with the capacitor. The change this would produce in the maximum charge that could be stored on the capacitor depends on the change in voltage across the capacitor. Voltage and charge for a capacitor are related through Q = VC. If the voltage
increases, the charge will increase; and if the voltage decreases, the charge will decrease. Based on that, vve could eliminate
choices B and C. What vve now have to decide is what effect the new resistor has on the voltage across thecapacitor. Without the new resistor, the voltage across the capacitor is 10mV. With the new resistor in the circuit, some of the 10 mV has to go on the resistor and some on the capacitor. Since the whole 10 mV is spread across two circuit elements instead of just the
capacitor, vve can conclude the voltage must decrease across the capacitor. The best answer is choice D.
228
42.
Choice Bis the best answer. If asteady current of 1mA passes through resistor Ri for 10 seconds, energy will be given off in the form of heat. The amount of heat is: Heat =(Power) x (time), so Heat =(I2R) x (time). Substituting values, vve get Heat =(1 mA)2 (5 mQ) (10 sec). Solve for Heat: Heat =(1 x 10'6) (5 x 10"3) (10) =5x 10"8 J. The best answer is choice
B.
43.
Choice C is the best answer. A discharging capacitor loses current in a characteristic fashion. When a capacitor is
discharging, it is losing charge, so charge as a function of time must decrease. This eliminates answer choices A and D. The
charge on a capacitor decreases exponentially, not linearly, so choice Bcan be eliminated. This can be explained by the fact that as the capacitor loses charge, there is less repulsion on its plates, resulting in a smaller electromotive force pushing
chargeoff the plates. The only graph showing nonlinear decay is choice C. The best answer is choice C.
Resistance is Futile
Choice B is the best answer. Devices (such as resistors) connected in parallel have the same potential difference. In order to measure the potential difference between two points in a circuit, the voltmeter must be connected in parallel. (This means that it does not matter which path the current takes to get from one point to another. It will lose the same amount of potential along either path.) Since vve do not want the voltmeter to affect the measurement, the voltmeter should have a large internal resistance. This will allow only a minimum amount of current to flow through the voltmeter-just enough to allow it to
measure the voltage difference. The best answer is choice B.
45.
Choice B is the best answer. In a parallel arrangement, the current that flows through one light bulb is not the current that flows through the remaining light bulbs. Remember that a parallel arrangement means that all bulbs have the same potential difference across them. If one bulb burns out, then current can no longer flow through that portion of the circuit; but the remaining light bulbs are unaffected, because they still have a potential difference across them. Devices wired in parallel are independent of one another. This favors choice B. Choice A is incorrect: In a series arrangement, the current in the circuit flows through all of the light bulbs. If one of the bulbs burns out, then current can no longer flow through that bulb or any
other bulb in the circuit. Devices wired in series are dependent on one another. This eliminates choices A, C, and D. The
best answer is choice B.
46.
Choice C is the best answer. The top branch, the middle branch, and the bottom branch of this circuit are connected in
parallel. This means all three branches have the same potential drop across their ends. Closing the switch and allowing current to flow through R5 does not change this. Closing the switch also does not change the total resistance of the top branch, the branch associated with all of the answer choices. If the potential drop across the top branch remains the same, and if the resistance remains the same, then by Ohm's law (AV = IR) the current cannot change. This eliminates choices A and B. However, something has to change when the switch is closed. By closing the switch, another resistor is added in parallel to the circuit. This will reduce the overall resistance of the circuit (the effective resistance of resistors connected in parallel is always less than the individual resistances). That, in turn, will increase the total current drawn from the battery (again, by Ohm's law). Current now can flow through R5 without affecting the current flowing through any other branch. The best
answer is choice C.
47.
Choice D is the best answer. Although the voltage in the wire may be very high, the voltage is measured with respect to the ground. The voltage will not vary as quickly along the wire. Thus, when the bird stands on the wire with both feet, every part of the bird is at approximately the same potential. Current flows only when there is a potential difference between two points. The bird would be in trouble only if it had one foot on the wire and the other foot on a different wire (at a different potential), or if it had one foot on the wire and the other foot on the ground. The best answer is choice D. Choice D is the best answer. When two or more resistors are connected in parallel, the equivalent resistance of the circuit is
48.
less than that of any one of those resistors alone. Closing Switch 2 adds another resistor in parallel. The circuit's Req should
therefore decrease. Thus, choices A and B are incorrect. Since R\ and R2 are connected in parallel, then when both switches
are closed, R\ has the same voltage drop across it as when Switch 1 alone is closed. Therefore, choice C is incorrect. Choice D is the only remaining choice, making it the best answer by the process of elimination. However, vve also know that choice
D is also correct because connecting resistors in parallel reduces the total resistance of the circuit. A circuit with a smaller resistance has a larger current, which consequently drains more power (P = IV). The best answer is choice D.
229
Questions 49 - 52
49.
Choice C is the best answer. A resistor is anything that drains energy from electrical flow and converts it to some other
form of energy, often light, heat, or work. A filament in a light bulb converts electrical flow into both heat and light, so choice A is a resistor. The heating coil in a hair dryer converts electrical flow into heat (and occasionally light), so choice B is a resistor. The magnetic coil of an electric motor converts electrical flow into mechanical work, so choice D is a resistor.
The anode of a Galvanic cell is the starting point for electrical flow, so it does NOT serve as a resistor. The best answer is
choice C.
50.
Choice A is the best answer. All three resistors are in parallel with each other, so they all experience the same voltage drop. This means that the resistor with the greater resistance will also have lower current. The ratio of the resistances is 2 : 1 : 2, so the ratio of the currents (I]-to-l2-to-l3) must be 1 : 2 : 1. This eliminates choices C and D. To decide between the remaining two choices, vve first need to solve for the equivalent resistance. Let's consider the resistors in duos, starting with the R1-R3 pair first. The quickest way is to take the product and divide by the sum, which in this case means (4 x 4)/(4 + 4) = 16/8 = 2. We can now take that 2 and pair it with R2 to get (2 x 2)/(2 + 2) = 4/4 = 1Q. Because the equivalent resistance is 1Q and the circuit voltage is 6V, the total current entering the junction is 6 amps. Adding the values listed in choice B for \\, I2, and I3 equals 8 amps, which is incorrect. Choice B is eliminated. In choice A, l\ + I2 + I3 = 6 amps, which is the value vve want.
The best answer is choice A.
51.
Choice C is the best answer. Adding a resistor in parallel will decrease the equivalent resistance for the entire circuit. Assuming the voltage remains the same, the total current will increase, not decrease. Choice A is eliminated. Adding a
resistor in series will increase the equivalent resistance of the circuit, but it will have no effect whatsoever on the total
voltage. Choice B is eliminated. Voltages add in series, so adding a battery in series will increase the total voltage of the circuit. Given that resistance does not chance, according to V = IR, the total current must increase. Choice C is a valid statement. Adding a capacitor in parallel will increase the equivalent capacitance of the circuit, but it will have no effect
whatsoever on the total voltage. Choice D is eliminated. The best answer is choice C.
52.
Choice D is the best answer. According to Kirchhoffsjunction rule, the current splits at junctions in such a way where the total current entering the junction must equal the total current leaving the junction. For the circuit in this question it means that I] =12 + 15 and 12 = 13 + 14- Because Ii = I2 + I5, Ij must be greaterthan I2, making choice A a true statement. Choice A
is thereby eliminated. Because I2 = I3 + I4,12 must be greater than I3, making choice B a true statement. Choice B is thereby eliminated. The voltage drop across R3 equals the voltage drop across R4, so given that R4 is greater than R3,14 must be less than I3. This eliminates choice C and leaves only choice D standing. Without knowing the exact values of R2, R3, R4, and
R5, there is no way to compare the currents through R4 and R5. For instance, if R2 is much larger than R5, then [5 will be
larger than I4 and I3 combined. However, if R5 is much larger than R2, then I5 will be small and could very likely be smaller than both I3 and I4. Because vve have no way to know for sure, vve can't say that I4 is definitely greater than I5. The best
answer is choice D.
230
Object
Lens 1 Lens 2
Image 1 = Object 2
by
the
Berkeley Review
Lightand Optics
Selected equations, facts, concepts, and shortcuts from this section
O Important Equations
v =A
Ephoton =h/
i
Ephoton =hc/*.
nisin6i =n2sin62
1 =1 + 1
f o
dt =Wo Xf)/{do . f)
Important Concept
m=himage/hobject =-ty^
With refraction, light bends towards the normal when going from a faster medium to a slower medium
Medium 1 faster and
longer wavelength
Normal J_ to interface
As n f: v | and 0 J,
Faster-to-slower
Medium 1
Medium 2
ni
n2
9A
Medium 2 slower and
n2>n!
shorter wavelength
Single diverging mirrors and lenses generate SUVs for images (smaller, upright, virtual images) Single converging mirrors and lenses generate images that vary with the object position and focal length
Converging Mirror Summary Object Positions
II
R
Object
Position
V
Object
Distance
Image
Formed
Smaller IR
Image
Distance
III
TV
V
UV image:
i = -#
I II III
dD>R
R
R>dj>f dj = R
Same size IR
ir
R>d0>f
d0 = f
f>d,
Larger IR
ds>R dj = oo
d; = -#
nr
IV
V
No image
Larger UV
Physics
Electromagnetic Radiation
Electromagnetic Radiation
Electromagnetic waves (often abbreviated as EM waves) are electrical and magnetic disturbances that propagate through space at the speed of light. The
speed of light c is taken to be 2.98 x 108 m/s. There are many types of
electromagnetic waves. Gamma rays, X-rays, microwaves, and radio waves are a few examples. All of these differ from one another in their wavelength A, and their frequency /. We can relate the wavelength and frequency of an electromagnetic wave to the speed of light by equation (10.1).
c = Xxf
(10.1)
The magnetic and electric fields of an electromagnetic wave are both perpendicular to one another and perpendicular to the direction of wave propagation. In Figure 10-1 we see a diagram of an electromagnetic wave
propagating at the speed of light from left to right. Note the alternations of the
electric and magnetic fields Vertical plane = Electric wave Horizontal plane = Magnetic wave
Figure 10-1
We can distinguish different electromagnetic waves by their frequency or wavelength in the electromagnetic spectrum (Figure 10-2). Low-frequency EM waves are used primarily for communication. These frequencies range from
about 0 Hz to 109 Hz. AM radio waves are at the lower end of this range, while FM radio waves and television signals are at the higher end. Microwaves fall
between 109 Hz and 1011 Hz. This type of EM radiation is used in navigation and
Visible light begins at about 4 x 1014 Hz and continues to about 7 x 1014 Hz.
periods of UV radiation exposure can also cause cancer. X-rays fall within the
Physics
X,(m)
101
10*"
10"
10"
Microwave-
Electromagnetic Radiation
k(m)
10"
10"
10'
10H
10"
10
10
-9
10"10
X-rays-
10"11
10
-12
10
-13
-^-Ultraviolet*"
Gamma rays10
20
Infrared
10
10
-<
10
12
Visible
/(Hz)
Red
750 to
630
Blue
490 to
440
Indigo Violet
440 to
420
/(Hz)
590 to
560
560 to
490
420 to Nanometers
390
Figure 10-2
Example 10.1a
If a charge oscillates in space, it emits electromagnetic radiation. If the charge oscillates with a fixed period and the wave speed of the emitted radiation subsequently decreases, then the electromagnetic wave will necessarily have:
I. a lower frequency. II. a shorter wavelength.
III. a lower energy. A. B. C. D. I only II only I and III only II and III only
Solution
rule actually holds for all types ofwaves andistherefore agood equation tokeep in mind whenever the word "wave" appears in physics problems. A decrease in the wave speed implies that either the wave frequency or the wavelength (or both) must decrease. The frequency of an electromagnetic wave is set by the source ofthewave. Since the oscillating charge hasa fixed period, it musthave a fixed frequency. Recall that therelation between frequency / and period T is: / = 1/T. We know the frequency is fixed, so Statement I is invalid. If ifs not frequency that decreased, then it must be the wavelength that decreased.
Therefore,Statement II must be valid, since v = fk. This leaves either choiceB or
D as the best answer.
When an electromagnetic wave travels through space or some material, its wave speed relates to its frequency and wavelength through the equation: v = fk. This
To make the correct choice, consider that Statement III says that slowing the wave will necessarily decrease its energy. How a wave's energy changes will
depend upon how it is slowed down. For instance, if the wave decelerates
quickly by hitting a glass surface, some of the light will be transmitted into the glass and some will reflect from its surface. Since energy is conserved, the transmitted wave must have less energy. However, if the wave speed is decreased slowly enough, there will be essentially no reflection; all the energy willbe transmitted. Therefore, Statement IIIis not necessarily true. This rules out choice D. You could also have reached this conclusion by knowing that the energy of a photon depends on its frequency according to E = h/. The energy does not change with wavelength or speed, as the speed-to-wavelength ratio is a
constant.
234
Physics
Example 10.1b
Electromagnetic Radiation
To increase the oscillation frequency of an electron (isolated in a vacuum) that oscillates because it is stimulated by an electromagnetic wave, one must: I. decrease the wavelength of the wave. II. increase the electric field amplitude of the wave. III. increase the speed of the wave.
A. I only B. II only C. I and III only
D. None of the changes will increase the oscillation frequency of the electron.
Solution
The electron is being stimulated by electromagnetic radiation in a vacuum, so we should start by noting that the speed of EM radiation in a vacuum is constant. This means that if the frequency of the radiation were to increase, the wavelength
would have to decrease (v = fk). This makes Statement I valid, which eliminates
choices B and D. We need to only consider Statement III at this point. Because the speed an EM wave in a vacuum is constant, Statement III can have no impact.
The best answer is choice A.
Polarization
Figure 10-1 diagrams a set of transverse, sinusoidal waves moving perpendicular to the direction of a propagating light wave. If we were to consider just the electric field vectors of that radiation, we would find they radiate outward from their source in all planes. The magnetic field vectors radiate in a similar manner.
Light like this, random in its orientation, is said to be unpolarized. But if we were to pass this light through a perfect polarizing filter, the vectors would radiate in only one plane, because the light wave hasbeen linearly polarized. The polarizing filter blocks all light perpendicular to the polarizing axis, but it allows the light aligned with the polarizing axis to pass through (Figure 10-3). The resulting light that does pass through the filter is called plane polarized light.
Polarization can result from transmission of light through a polarizing filter or
235
FhysiCS
Electromagnetic Radiation
Note that the electric field vector of the light that has passed through the filter is parallel to the polarizing axis of the filter. Measuring the intensity of this light in a photocell would reveal that it has half the intensity of the unfiltered natural light. To demonstrate why, we could break the electric field vector of unpolarized electromagnetic radiation into its components, one parallel and one perpendicular to the axis of polarization. On average, these two components are equal. But since the polarizing filter allows just the electric field vectors parallel to its plane to pass through the filter, only half of the unfiltered natural light passes through.
Example 10.2a
Vertically polarized light is sent through an empty sample cell and then into a horizontally oriented polarizer. No light gets through the polarizer. The experiment is repeated, this time with a dilute solution of aqueous D-Glucose in
the cell, and one-quarter ofthe incident lightintensity gets through the polarizer. What must be TRUE of the solution and the rotation of the polarized light? (Assume that thesolution transmits all the incidentlight to the polarizer.) A. Thesolution is optically active and rotates the polarization by 30. B. Thesolution is optically active and rotates the polarization by 45.
C. D-Glucose is an asymmetric molecule and the solution rotates the polarization by 60. D. D-Glucose is an asymmetric molecule and the solution rotates the polarization by 90.
Solution
the polarization oflight passing through them. This activity usually arises from an asymmetry in the structure and/or orientation of the molecules that make up the material. Here, the solution is optically active--the activity arises from the
helical, and therefore, asymmetric structure of the D-Glucose molecules. This mightbe illuminating, but it doesn'thelp to isolate the best choice, because all of
We need to think about the optical properties of the solution's molecules and the polarization rotation. First optically active materials are materials that can alter
incident upon it. To calculate the amount of linearly polarized light getting
through a polarizer, useequation (10.2), Malus' law: I=I0cos2 6
(10.2)
The light that does get through the polarizer isone-quarter as intense as the light
where I is the intensity of light getting through the polarizer, when an initial
intensity I0 is incident upon the polarizer. The angle 8 is the angle between the
Cos 60 = 0.5, so cos2 60 = 0.25, meaning that 6 must be 60 with respect to the
oriented, the exiting light must be at an angle 30 to the vertical. The solution must have rotated the polarization of the initially vertical light by 30. This is to say that the light exitinglight has an orientation closer to vertical than horizontal,
so the angle must be less than 45.
The best answer is choice A.
236
Physics
Example 10.2b
Electromagnetic Radiation
When unpolarized light reflects offof a specular (mirrored) surface at a glancing angle with respect to the surface, the light can partially polarize parallel to the surface. That is, the parallel polarized light is more intense than the perpendicular polarized light. If this surface is lying on flat ground, in what orientation should a polarizing anti-glare filter be with respect to the ground, in order to minimize the total light intensity through the filter? The polarizer's
polarization axis should be oriented at: A. B. C. D. 0 with respect to the ground. 45 with respect to the ground. 90 with respect to the ground. 180 with respect to the ground.
Solution
This question is a topic unto itself. When light strikes a surface, some of the light reflects(bounces off if you will) and some refracts (passes into the new medium). When unpolarized light strikes that surface, certain orientations of the electric wave are more apt to reflect and other orientations are more apt to refract. The question states that light with an E wave parallel with the surface is more apt to reflect than refract. Hence, the reflected light is semi-polarized in a horizontal fashion. The reflected light is richer in horizontally polarized light than it is in vertically polarized light. To filter out the reflected light (glare), the polarizing filter should be a vertical polarizer.
237
Physics
When a wave strikes the boundary between two media, we find typically that some light is reflected, some transmitted, and some absorbed. We want to consider for the moment the light that is reflected from the boundary.
Suppose a light beam strikes the surface of a mirror (Figure 10-4). The incident light ray strikes the mirror at some angle 8i with respect to a line perpendicular to the mirror. The reflected light ray leaves the surface of the mirror at an angle 8r, which is equal to Of. The law of reflection says that the angle an incident light ray makes with a surface is equal to the angle that the reflected light ray makes
with the surface.
Reflectedlight ray
Figure 10-4
Refraction
Electromagnetic radiation that passes through a vacuum travels at the speed of light, c. However, in a medium other than a vacuum the velocity of the wave depends on the medium itself. The index of refraction n is the ratio of the speed c of an electromagnetic wave in a vacuum to the speed of that wave in a given medium. This is given by equation (10.3). Note that the index of refraction is
expressed without units.
n _ c_ _ vvacuum
vmedium
(10.3)
The velocity of an electromagnetic wave in a medium other than a vacuum can never be greater than the speed of light. Therefore, the index of refraction will
never be less than 1. In Table 10-1, we list the indexes of refraction for some
Medium
Vacuum Air
Medium
Index of Refraction
1.483 1.501 1.517 2.417
Carbon Dioxide
Water
1.00045
1.333
Table 10-1
The source of the light wave will establish the wave's frequency. The frequency of this waveis not typically altered as it travels through some medium; thespeed and wavelength of this wave, however, are altered. From equation (10.1), we know that v = fk. From equation (10.3), we know that v = c/n. If we set these two expressions equal to one another as shown in equation (10.4), we can see that as the index of refraction changes, so does its wavelength of light (remember, the
speed of light c is a constant).
(10.4) (10.5)
**-
238
"2
ki
Physics
Suppose that a beam of light passes from a medium with an index of refraction
ni (where ni = c/f-ki) to a medium with index of refraction n2 (where n2 =
clf'ki). The wavelength of that light changes according to equation (10.5). Note that the wavelength of light is shorter in a medium with a greater index of refraction. Refraction affectsboth the speed and wavelength of light.
Example 10.3a If an Earthbound scientist reflects a laser beam from a mirror left on the Moon by astronauts, how long in seconds will it take the beam to make the trip from the Earth to the Moon and back? Assume that the Earth is approximately 250,000 miles from the lunar surface and that the speed of light is 186,000 miles/second.
A. t =
186,000
2(250,000)
250,000
B.
2(186,000) 2(186,000)
250,000
C.
t =
D. t =
2(250,000)
186,000
Solution
This is a formula-identification type of problemexcept with the numbers are already plugged in. You can use units or limiting cases to narrow the choices. You want units of time, so the choice must be either B or D. Using limiting cases, what should happen to the travel time, if the travel distance increases? It should
increase, too. This method also isolates choices B or D. Which is better? The laser
beam is making a round trip, so the 2 in the formula has to multiply the distance, not the rate of speed. The 2 must be in the numerator.
The best answer is choice D.
Example 10.3b
Neglecting absorption and scattering, how long does it take for light to traverse 2
m of H2O, which has an index of refraction equal to 1.33?
A. t =
2(1.33)
3xl08
B. t =
3xl08
2(1.33)
C.
D.
t_(3xl08)(1.33)
t =
(3xl08)(1.33)
Solution
If you don't recall distance = rate x time, then you can get the relationship from the units. The time is equal to the distance divided by the rate. The distance is 2 and the rate is (3.0 x108)/1.33. Both2 and 1.33 should be in the numerator.
The best answer is choice A.
239
Physics
As a light ray moves from a medium like air to a medium like water, it is refracted. Suppose that the indexes of refraction of the two media are ni and n2, respectively. The incident light ray has an angle 81 with respect to the normal as it strikes the water and an angle 82as it passes into the water (Figure 10-5).
Incident light ray
Air (nx)
Water (n2)
5v
Figure 10-5
nisin8i = n2sin82
(10.6)
If n2 > ni, the light ray will bend towards the normal, while if n2 < ni, the light
ray will bend away from the normal.
Example 10.4a
If the index of refraction doubles for a liquid (in which a coin is submerged), the
apparent depth of the coin when viewed from the air above, will:
A. B. C. D.
increase, and it appears at a position shallower than its true depth. decrease, and it appears at a position shallower than its true depth. increase, and it appears at a position deeper than its true depth. decrease, and it appears at a position deeper than its true depth.
Solution
Apparent depth is the depth at which you think an object is submerged; it may vary from the object's true depth because of refraction. For example, if you look at a coin in a fountain, you may think the object is higher than it actually is. The real coin is at the bottom; you may think ifs only a few feet from the surface.
Refracted light ray (bends away from normal)
Air (nair = 1.0003)
240
Physics
Light coming from the surface ofthe coin bends as it goes from the water into the
air (and into your eyes). Because the index of refraction of water is greater than that of air, we can deduce that 8air> 6water, and thus light bends away from the
normal. Your brain will think that the coin lies on a direct path from your eye to
thecoin's apparent position (asshown in the diagram above). This apparentlight path (represented by the dashed line) is, however, higher than the true light path; you think that the coin is higher than it truly is. Thus, the apparent depthof a submerged object is less than its true depth. The answer mustbe either A or B.
Now, increasing the refractive index of the liquid medium would only exaggerate thebending. You would then think the apparentdepth had decreased (i.e., the coin would appear to be closer to the surface). That rules out choice A
and leaves us with choice B. The best answer is choice B.
Example 10.4b
The material n2 has parallel sides, and is surrounded by media with ni and n3.
Under which conditions will 8 exceed (J>?
A. B. C. D.
Solution
Because the two interfaces are parallel to one another, the intermediate medium (with an index of refraction of n2) does not impact the path of the light ray. The
incident ray (in medium1) and final refracted ray (inmedium 3)will be the same whether or not the light passes through medium 2. That can be quickly proven using Snell's law to evaluate the two refractions and then setting them equal to
one another.
This means that the value of n2 has nothing to do with either angle in the
question (8 and <J>), so choices C and D can be eliminated. If8 >4>, thenoverall the
final refracted ray has bent towards the normal relative to the incident ray. The lightray bends towards the normal when it slowsdown,so we can conclude that the speed of light is slower in medium 3 than medium1. A slowerspeed of light means that the medium must have a larger index of refraction. This means that
n3 must in fact be larger than ni.
The best answer is choice B.
241
Physics
refractive index to a medium of low refractive index. If this refracted light ray were to keep bending away from the normal as the incident angle increases, it would eventually reach a refracted angle that is 90 away from the normal. This
incident angle is called the criticalangle 8C.
A light ray bends away from the normal as it moves from a medium of high
Suppose a skindiver shined an underwater light toward the surface above, as shown in Figure 10-6a. If a lightray from the underwater sourcestruck the water surface at the critical angle, it would be refracted along the surface of the water.
If the light ray were to strike the water surface at an angle to tiie normal that is less than 80 the refracted ray would pass into theair. But what would happen if
the lightray struck thesurface at an angle largerthan 8C (Figure 10-6b)? It would be reflected (not refracted) off of the surface of the water. This phenomenon is called total internal reflection; and we know it must work this way, because Snell's law tells us thatthesine ofa refracted angle can never be greater than 1.0!
Incident
Incident
light ray
Light at crtical angle
Figure 10-6 Example 10.5a
light ray
; Refracted
light ray
Total Internal Reflection
different optical densities and that it travels within the optically denser material. For which two indexes of refraction will its critical angle for total internal
reflection be the SMALLEST?
A. B. C. D.
When the indexes of refraction are 1.00 and 1.33. When the indexes of refraction are 1.00 and 1.01. When the indexes of refraction are 1.00 and 1.52. When the indexes of refraction are 1.46 and 1.88.
Solution
Total internal reflection can occur only when light starts out in an optically denser medium (i.e., higher n) and then hits an interface with an optically less
dense medium. The critical angle comesfrom Snell's law:
("less "dense")( (sin 8ieSs "dense") = (nmore "dense")( (sin8more "dense") To get the critical angle, set the anglein the less "dense" (i.e., optically lessdense) material to 90 (since, thatis the material thelightwill not getinto). This gives:
(niess "dense")( (sin90) = (nmore "dense")( (sin Scntical)
Solving for the criticalangle yields:
sin 8 critical
nless "dense"
^ore "dense"
242
Physics
The important factor in determining the critical angle is the ratio of the refractive
indexes. Therefore, the choice with the smallest ratio of indexes must be the
Example 10.5b
Fiber optic cables can transmit light, because light in the cable achieves total
internal reflection as it travels. From which material could the BEST fiber optical cable be made for use in air, if the best cable is one that would let no light rays
escape into the air, regardless of the degree to which the cable may be bent?
A. An aerogel, with n = 1.05 B. A polymer gel, with n = 1.35
C. Glass, with n = 1.50
Before attacking the question, you might have noticed that this is an extreme type of question. The best material will be one of the extremes, either the material
with the smallest index of refraction or the material with the largest index of refraction. In order to increase the number of angles of incidence that result in total internal reflection, we want a critical angle as close to perpendicular to the
surface as possible. A perpendicular incident ray would have an angle of 0 with respect to the normal, so we are looking for a material with the smallest critical angle. This can be seen in the diagram below, where we consider the range of angles that could generate total internal reflection (TIR) for both a large critical
angle and a small critical angle.
nless "dense" nless "dense"
nmore "dense"
Note from the pictures that a small critical angle allows for more potential incident angles that result in total internal reflection. We can also get this by
math if we relate the critical angle to the index of refraction for a material. In Example 10.5a we learned that:
nless "dense"
sin Critical
nmore "dense"
This confirms that we are looking for a material with a very large index of refraction to be in the denominator on the right side of the equation, so that the sin Scritical can be as small as possible. The best answer is the material with the
243
Physics
Dispersion In Figure 10-2 we saw that the visible portion of the electromagnetic spectrum
varies from about 750 nm to about 400 nm. Electromagnetic waves of different
with the wavelength. This gives rise to an effect known as dispersion. A good example of a dispersive medium is a prism. If we pass white light through the prismshown in Figure 10-7, we see that the colors of the visible spectrum refract according to their wavelengths. [Note that red light is deflected the leastfrom its
original direction of travel, while violetlight is deflected the most]
Red(=750nm)
kf
1 Orange
Yellow Green Blue
*/
Two initially parallel visible lightrays, A and B, are incident upon onesurface of
speeds within the material?
a prism. Which of the following is true regarding their wavelengths and wave
A. B. C. D.
Solution
When two rays bend differently upon entering a new medium, their indexes of refraction must be different. The ray that bends more has a higher refractive
index; Ray Ahas the higher n. Now, consider how the wavelengths and speeds of the light rays are affected within the prism. Because v = c/n, Ray A must
move more slowly than Ray B. This rules out choices A and B. To determine the
244
Physics
In the visible spectrum, light of a higher frequency refracts more than light of a
lower frequency (i.e., n is higher for higher /). Given that va is less than vb, for frequency to remain constant as a ray changes medium, Xa must be less than k&. Ray A has a smaller wavelength than Ray B. That is, if / remains constant and v decreases, then Xmust also decrease (in order for the equation to balance).
The best answer is choice D.
Example 10.6b
Polychromatic light refracts through a prism and strikes a screen. Which plot of intensity versus screen position BEST represents this set-up?
Intensity
10 3
7
X(nm)
488
Color Blue
Green Red
530
633
A.
B.
Intensity
C
D.
Intensity
Intensity
Solution
Intensity
This question tests whether or not you know that a shorter wavelength of light will exhibit greater bending when undergoing refraction. This means that blue light will bend the most of the three colors used in the experiment Because blue light has the greatest intensity (according to the data in the table), the lowest peak on the screen should have the greatest area (be the biggest). This eliminates
choices A and B.
Green light has the lowest intensity of the three colors, so the smallest peak
should be found in the middle of the screen, where green light would strike
eliminates choice C.
having bent an amount somewhere between the extremes of red and blue. This
245
Physics
Optics
Optics
Optics, as we shall study it, is applied geometry. When light emanates from an object, that light can interact with such optical devices as a mirror (reflective
surface) or a lens (refractive object through which light transmits). Because the light can be altered by the mirror or lens, there is the chance that it will cast an image that is altered with respect to the original object. We shall study the relationship betweenan object, the optical device,and the image it casts.
General Rules
Because we are dealing with positions of objects and images, we will establish what in essence is a number line where the (+)-side represents the region of space where a real image can form and the (-)-side represents the region of space where a virtual image can form. A real image is one that can be projected onto a screen, while a virtual image cannot be cast onto a surface. We also have rules that describe the magnification of an image relative to the object These rules will define the size of the objectand whether the image is upright or inverted with respect to the object The numerical rules are shown in Table 10-2.
Real/Virtual
Convention
i > 0
i < 0
Image
Real
Virtual
Upright Enlarged
Same size Reduced
Table 10-2
(10.7)
When you consider this equation, it is important to keep the signs correctThere
are a few conventions to keep in mind:
1.
Focal Length (f): This value is positive (+) for a converging lens
or mirror and negative (-) for a diverging lens or mirror.
2.
Object Distance (s, p, or o): If the object is to the left of the lens, this value is positive (+). If the object is to the right of the lens, this value is negative (-).
Image Distance (s', q, or i): Real images will give a positive (+) value, while virtual images will give a negative (-)value.
3.
You may have noticed that three different letters can be used to represent the image distance as well as three different letters representing the object distance. Because all three are seen in physics, we will interchange them between examples and questions without any rhyme or reason to our usage. The goal is to get you used to more than one letter representing image and object.
Copyright by The Berkeley Review
246
Physics
Mirrors
Optics
A mirror is an optical device that can alter the path of light coming from an object Mirrors focus light by reflecting it There are three general types of mirrors. A plane mirror is flat and resembles the one on your bathroom wall. A concave (converging) mirror has its reflecting surface on the inside of a curve. A convex mirror (diverging) has its reflecting surface on the outside of a curve. The location of an image produced by a spherical mirror can be calculated by using equation (10.7). Both mirrors and thin lenses use the same equation. The
linear magnification produced by a mirror can also be calculated from the object's height and image height, and we will do in several examples. For now, however, we'll just say mat the magnification is a ratio of the image height to the object's height. In Figure 10-7, we see examples of images produced by a plane
mirror, a concave mirror, and a convex mirror.
Plane Mirror
*r
Image
ALWAYS
I
-*+*-
I
Concave (Converging) Mirror (f = + #)
Image
f
ALWAYS
*"* R
Smaller (I<f)
Figure 10-7
When you look at these examples, note whether the image produce is real or virtual. For a single plane mirror and single diverging mirror, the images will always be inverted and virtual. For a converging mirror, we will consider what
the right of the focal point Regarding the focal length associated with a spherical
mirror, its size relates to the radius of curvature of the mirror as equation (10.8):
type of image would be produced, ifthe object were placed either to the left orto
f=K
2
(10.8)
where R is the radius of a sphere that would be formed if the mirror were a complete sphere.
247
Physics
Optics
While the images produced by plane mirrors and diverging mirrors are predictable, the image produced by a converging mirror takes some effort to determine. We will look at five different scenarios, and then generate a summary chart that will be our guide when answering questions. Consider the objectat the following five positions relative to the R and f of a converging mirror.
Objectbeyond the radius of curvature. Objectat the radius of curvature. Object inside the radius of curvature but beyond the focal point Objectat the focal point Objectinside the focal point.
Before we start lefs considerthe thin lens equation for an objectthat is exactly 2f from the mirror. According to equation (10.7), the image should also form at 2f. This can be manipulated and rewritten as equation (10.9).
t =L +L
R R
(10.9)
This is going to provide a useful hint when analyzing image formation associated with converging mirrors and lenses. Let's start by considering Case I, where the object is positioned outside the radius of curvature. In order for the thin lens equation to hold true, if the object is beyond R, then image must form inside of R. This is to say that if one of the denominators on the right in the equation (10.9) is greater than R, then the other denominator on the right mustbe lessthan R. Consider the ray diagramfor Case I shown in Figure10-8.
Case I: Object Beyond the R of a ConvergingMirror
Object
f^-^
#>r
#<r
Figure 10-8
This will serve well asa short cutin thefuture. For instance, if the question were to ask about the image formed by a converging mirror with a focal length of 15 cmby an object thatis 45 cmfrom the mirror, then we could do a quick analysis
as follows:
If f = 15 cm, then R = 30 cm. The object is beyond R, so the image will form betweenf and R, meaning it willbe an invertedand real image foundbetween 15 cm and 30 cm. This may be enough information to nail down the best answer on a multiple-choice exam. We shall do this for each of the five positions and in the end realize thatthese questions can be solved withoutinvoking raydiagrams.
248
Physics
Optics
1=J_
f ~ R+ R
-I
Figure 10-9
When the object is located at the radius of curvature for a converging spherical mirror, the image that forms will be an inverted, real image also located at the
radius of curvature. Now lefs consider the ray diagram for Case III shown in
Figure 10-10.
1 + l
f #<R #>R
When the object is located inside the radius of curvature but beyond the focal length for a converging spherical mirror, the image that forms will be an inverted, real image located beyond the radius of curvature. Now lefs consider the ray diagram for Case IV shown in Figure 10-11. Case IV: Objectat the f of a Converging Mirror
No Image Forms
(I = oo)
Figure 10-11
249
Physics
Optics
When the object is at the focal length for a converging spherical mirror, no focused image forms, although it can be said that the image forms at infinity. Now lefs consider the ray diagramfor CaseV shown in Figure 10-12.
CaseV: Object Insideof the f of a Converging Mirror
^n Virtual, Upright,
and Larger Image Image
Figure 10-12
Now that we've considered all five cases, we can keep a summary in our mind
and apply the information to answer multiple-choice questions quickly. Try to complete the following two questions in less than fifteen secondseach.
Example 10.7a What is true of the image formed by a converging mirror with a focal length of 25 cm by an objectthat is 40cm from the mirror?
A. B. C. D.
It is an inverted, real image that forms 66.7cm from the mirror. It is an inverted, real image that forms 33.3 cm from the mirror. It is an upright, virtual image that forms 33.3cm from the mirror. It is an upright, virtual image that forms 66.7 cm from the mirror.
Solution
The pertinent facts are (1) a converging mirror and (2) the objectis between f and R. This makes it a scenario like Case HI, where the image forms beyond the R. If f = 25 cm, then R = 50 cm, so the image must form beyond 50 cm. ChoicesB and C are eliminated. Objects beyond the focal length of a converging mirror form upright, real images, eliminating choiceD.
The best answer is choice A.
Example 10.7b
What is true of the image formed by a convex mirror with a focal length of 20 cm by an object that is 30 cm from the mirror? A. B. C. D. It is an inverted, real image that forms 60 cm from the mirror. It is an inverted, real image that forms 12 cm from the mirror. It is an upright, virtual image that forms 12 cm from the mirror. It is an upright, virtual image that forms 60 cm from the mirror.
Solution
The pertinent fact is (1) ifs a diverging mirror. For a diverging mirror, the image is always upright and virtual, forming inside of f. If f = 20 cm, then the image distance must be less than 20 cm. Choices A and D are eliminated. Objects reflectedin a diverging mirror form upright, virtual images, ousting choiceB.
The best answer is choice C.
250
Physics
Lenses
Optics
Light rays coming from an object can be altered if they pass through a lens. A lens is an optical device with two curved, non-parallel refracting surfaces. There
axis that passes through the center of the lens and to converge at a single point called the focal point f. The focal length for a converging lens is always a positive
value. This is shown in Figure 10-13a. Because light can enter the lens fromboth its rightand leftsides, the lens has two focal points.
(a)
are twotypesof lenses to consider: converging and diverging. A converging lens (convex lens) with smooth surfaces allows parallel light rays to bend toward an
Converging Lens (f is a + #)
(Also known as a Convex Lens)
Diverging Lens (f is a - #)
(Also known as a Concave Lens)
Figure 10-13
A diverging lens (concave lens) allows parallel light rays to move apart as they pass through the lens. As shown in Figure 10-13b, the focal lengthof a diverging lens is a negative value. This is because the diverging light rays appear to leave a single focal point from the side of the lens that light enters. Like converging lenses, diverging lenses will also have two focal points.
As light passes through a lens, either a real image or a virtual image can be formed. The rules for single lenses are the same as they are for single mirrors, except that the real and virtual sides are flipped and convex and concave are reversed. As was the case with mirrors, diverging systems generate smaller,
upright, virtual images. Converging systems, be it lenses or mirrors, also share similar rules. Lefs consider the formation of a real image using a converging lens. This can only occur if the object is outside of the focal length. An object is placed a distance s to the left of the lens, as shown in Figure10-14.
Virtual side
Real side
Object
Figure 10-14
Light rays leaving this object travel in all directions, and some of them pass through the lens. Of all the rays that pass through the lens, we will focus our attention on just two of them. They pass through the lens to form an inverted
image of the object at distance s' to the right of the lens. Because the light rays
pass through the lens and come together to form an (inverted) image of the object, that image is called a real image. One property of real images is that only they can be cast upon a screen, photographic negative, or retina. Thus, lenses in camerasand eyes have focal lengths that produce real images.
Copyright by The Berkeley Review
251
Physics
Optics
Now lefs consider the formation of a virtual image using a converging lens. This
is only possible if we place our object between the focal point and the lens, as shown in Figure 10-15. As tiie lightrayscoming from the object pass through the lens, they will diverge on the right side. If we follow those diverging rays back through the lens (dashed lines), we find thatthey intersect at a point Ato the left of the object Since no light rays from the object intersect at that pointin space,
the image at that point is said to be virtual.
Image
Virtual side X
Real side
Figure 10-15
Magnification
Suppose we wanted to know the height of our image h' relative to the height of the objecth in Figure 10-14. This is called linear magnification m and is given by equation (10.10). The linear magnification value is unitless, and the conventions are listed in Table 10-1. In Figure 10-8, the object with height h is upright pointing above the axis. The value of h is taken to be positive. The inverted image with height h' is below the axis. The value of h' is taken to be negative.
m
h'
(10.10)
Consider s, s', h, and h' in Figure 10-14. We can relate these four variables to one another using geometry, where the height-to-length ratio (h : s) is the same for both the object and the image. Both ratios need to have the same sign, so a negative sign is included. This relationship allows us to use the objectand image distances to calculate the linear magnificationusing equation (10.11).
m = (10.11)
The point of preparing for the MCAT is to be able to answer questions quickly.
As such, lefs develop a plan ofattack for questions dealing with either a single
lens or a singlemirror. Tnefollowing three-stepalgorithm should prove useful.
1.
2.
3.
Identify whether the system is diverging or converging. Keep in mind that convex lenses and concave mirrors are converging systems, so you must do some work to determine whether the optic device is converging or diverging. If tiie optic device is diverging, then the image will be smaller than the object, upright, virtual (an SUV), and found between the focal length on the virtual side and the optic device. If the optic device is converging, then we need to do a positional analysis to see which case it fits out of I through V. Sketch a diagram of the object, optical device, and image. Double checkusing equation (10.12) (a shortcut version of equation (10.7).
l =
oxf o-f
(10.12)
252
Physics
Example 10.8a
Optics
A. It is an upright, virtual image that is found 60 cm to the left of the lens. B. It is an upright, virtual image that is found 8.7cm to the left of the lens.
C. It is an inverted, real imagethat is found 8.7 cmto the right of the lens. D. It is an inverted, real imagethat is found 60 cmto the right of the lens.
Solution
Lefs use the three-step method. First off, a concave lens is a diverging system. Second, because ifs a diverging system, the image will be upright, virtual, smaller than the object, and found between the focal length on the virtual side and the optic device. The image distance must be less than 15 cm, eliminating
choices A and D. Because ifs a lens, the objectis on the virtual side, so a virtual image will form to the left of the lens, eliminating choiceC. The third step is not necessary here, because only one answer choice remains standing.Butlefs considershow the step for a sense of completion.
o xf
i =
20 x (-15)
-300
35
o-f
-60
20-(-15)
Object
20 cm
-300
= = - 8.somethmg
Test Tip
Calculation Shortcut
Example 10.8b What is true of the image formed by an object 50 cm from a convex lens that has a radius of curvature equal to 60 cm?
A. B. C. D.
It is an inverted, real image that is found 75 cm from the lens. It is an inverted, real image that is found 30 cm from the lens. It is an upright, virtual image that is found 30 cm from the lens. It is an upright, virtual image that is found 75 cm from the lens.
Solution
Lefs use the three steps listed above. First off, a convex lens is a converging system. Second, because ifs a converging system, we need to determine which scenarioit fits. The objectis between R and f, so an inverted, real image will form beyond R The image distance must be greater than 60 cm, eliminating choices B and C. Becausetiie image is real, choice D is eliminated.
Object @50 cm
60
cmft_
1500
20
>60cm
30 cm
Image
30 cm 60 cm
o x f
i =
50 x 30
o-f "50-30
= 75
Test Tip
V
Calculation Shortcut
253
Physics
Optics
Example 10.9a
An object is moved from within the focal length of a converging lens to a distance beyond the focal length. During this repositioning, the image of the
object is observed to change from: A. uprightand virtual toinverted and real. B. upright and realto inverted and virtual.
C. inverted and virtual to upright and real. D. inverted and real to upright and virtual.
Solution
Looking at howthelight bends(and theimage forms) in Figures 10-14 and 10-15, we see that the image will go from upright to inverted. The answer must be either choice A or B. The image is virtual when the object is inside of the focal length, but real once the object is beyond the focal length. The object starts inside the focal lengthand is moved to outside the focal length,so the image goes from being upright and virtual to inverted and real. This makes choice A correct.
Upright, virtual
Image
Object inside f Object outside f
J.
Inverted, real
Image
Two ideas for to remember for a single lens or a single mirror, are the following: Upright images are always Virtual, and Inverted images are always Real. Just remember UV-IR. This relationship works for any single lens or single mirror
(whether it be convex, concave, or flat).
The best answer is choice A.
Example 10.9b
When an object is moved from within tiie focal length of a diverging lens to a distance beyond the focal length, the image is observed to:
A. change from upright to inverted, and move away from the lens. B. change from inverted to upright, and move closer to the lens. C. remain upright and move away from the lens.
D. remain inverted, and move closer to the lens.
Solution
This question is testing you on pure memorization from this section. Because the virtual rays for a diverging optical device start from virtual focal point, the rays
will always intercept at some point between the surface ofthe optical device and
the focal point on the virtual side. This means that for a single diverging lens or a single diverging mirror, the image will always be an upright, virtual image that is smaller than the objectand is found between -f and 0. Keep in mind that for a diverging lens or mirror, we use the negative focal length. This makes for a nice short cut. The image will remain upright, so choices A, B,and D are eliminated.
The best answer is choice C.
254
Physics
Example 10.10a
Optics
A diverging lens has a focal length of 10 cm. If an 8-cm tall vertical arrow is
placed 25 cm to the left ofthe lens, the resulting image will be approximately:
A. 7 cm to the left of the lens, upright, and reduced. B. 15cm to the right of the lens, inverted, and reduced.
C. 35 cm to theleftof the lens, upright, and enlarged. D. 250 cm to therightof the lens, inverted, and enlarged.
Solution
Lefs solve this problem in three ways: using the shortcut first, the picture method second, and then equation (10.12) last. Because ifs a diverging lens, the
length is 10cm, the image must form at some distance less than 10 cm. Only
choice A fits this restriction, so it must be the best answer.
image will be upright and virtual, formed between 0 and -f. Because the focal
If you opt not to use the shortcut method, then tracing is often fast for problems of this nature; make a quick picture before doing long math. The two rays to
draw are shown below. One ray goes through the centerof the lens, as it does for a converging lens. The other is parallel to the optical axis, diverging from the left focal pointas it passes through the lens. Since the two real rays (on the rightside of the lens) do not intersect, they must be extrapolated backwards to a common
point-this point locates the image. The image is to the left of the lens, within the 10-cmfocal length, and reduced; this makes choice A the best choice.
Object
25 cm
For the algebra fans, lefs use the modified version of the thin lens equation (equation (10.12)) to solve this problem without resorting to all of that slow and painful drawing. Using the sign conventions, the problem asks for i, given o =
+25cm and f = -10 cm. A quick bit of calculation gives:
o xf _ 25 x(-10)
i =
o-f
-7-ta,
This again supports choice A. You have three methods, and which you choose
should be both fast and comfortable for you. Just to confirm the fact that the image is reduced, which occurs whenever the image is closer to the optical device than the object, lefs apply equation (10.11) and solve for the magnification. This gives M = +7/25. The image will be 7 cm to the left (i < 0) of the lens, reduced (M < 1), and upright (M > 0). This is choice A. Although the math can produce the correct answer, it requires you to know the sign conventions for thin lenses (a knowledge that can easily slip away under the
pressure of a timed test).
The best answer is choice A.
255
Physics
Optics
A diverging lens hasa focal length of10 cm. If a 4-cm tall vertical arrow is placed
7 cm to the left of the lens, the resulting image will be approximately:
Example 10.10b
A. B. C. D.
3 cm to the right of the lens, inverted, and reduced. 4 cm to the left of the lens, upright and reduced. 17 cm to the left of the lens, upright, and enlarged. 70cm to tiie right of the lens,inverted, and enlarged.
Lefs again solve this problem in three ways: using the shortcut first, the picture method second, and then equation (10.12) last. Because ifs a diverging lens, the image will be upright and virtual, formed between 0 and -f. Because the focal length is 10cm, the image must form at some distance less than 10 cm and onthe
left side of the lens. Only choice B fits this restriction.
We can also use a ray trace.
Solution
For those fond of algebra, lefs use the modified version of the thin lens equation (equation(10.12)) to solve this problem. Using the sign conventions, the problem asks for i, given o = +7 cm and f = -10 cm. A quick bit of calculation gives:
oxf _7x(-10) __70
i =
z68 =-4
17
o-f
7-(-10)
17
This again supports choice B. Just as we saw with Example 10.1a, you have three methods, and which you choose should be both fast and comfortable for you. Just to confirmthe fact the image is reduced, which occurs whenever the image is closer to the optical device than the object, lefs apply equation (10.11) and solve for the magnification. ThisgivesM = +4/7. The image will be 4 cm to the left (i < 0) of the lens, reduced (M< 1),and upright (M > 0), which fits only choiceB.
The best answer is choice B.
256
Physics
Combinations of Lenses
Optics
Things get a bit more complicated when there are multiple lenses within an
optical system. The basic rule to multiple lens systems is that the image of the
first optical device is the object of the second optical device and so on for any additional lenses. Most multiple-lens devices have two lenses total. Depending on the goals, the optical system can enlarge a small object, reduce a large object, or make a far away object seem near. Optical instruments like binoculars, telescopes, and microscopes contain more than just a single lens. Lefs consider a symmetric two-lens system. In Figure 10-16, we see two converging lenses separated by a distance d. For simplicity, the two lenses have identical radii of curvature. The object that we are interested in is at a distance si from Lens 1.
Figure 10-16
By using equation (10.12), we can determine where the image si' will be located. The first image is shown in Figure 10-17. Note the image is inverted, because the
object is outside of fi.
Object
Figure 10-17
We now let our inverted image be the object for Lens 2 (see Figure 10-17). This
requires that we calculate how far away the new object is from the left side of Lens 2, by using the relationship S2 = d - si'. The final image can be found by using equation (10.12) again, where o is replaced by S2 and i is replaced by S2'. Keep in mind that the test writers are free to use any of the common designations for image position, focallength, and objectposition.
s2' = S2*f2
s2-f2
If the value of S2' is positive (+), the image is a real (Figure 10-18). If the value of S2' is negative (-), the image is virtual. Because the first image (and objectof Lens 2) is outside of f2, the final image will be a real image on the right side of Lens 2.
Copyright by The Berkeley Review
257
Physics
Object
Optics
Final
Image
Figure 10-18
In this example, we chose a symmetric pair oflenses and placed them in such a
way where their R points were essentially at the same point. When the lenses are of unequal radii of curvature and the system is not symmetrical, it may prove to be a bit more challenging to visualize. Math may prove to be the tool of choice
for more complicated systems.
A microscope is an example of an asymmetric system, where the first lens (referred to as the objective) is placed in such a fashion that the object is close to or at its focal point This allows the image to be extremely magnified before being magnified and inverted by the second lens (referred to as the ocular or eyepiece). The magnifying power of a microscope is a product of the magnifications of both
lenses.
Lens Aberrations
Real lenses can produce aberrations, owing to their shape and composition, so they do not always cast perfect images of an object. When lenses are not shaped properly, many types of aberrations can arise. Three common aberrations are spherical, astigmatic, and chromatic aberrations. Spherical aberrations develop when a misshapen lens still has cylindrical symmetry with respect to the optical axis,but has not been properly rounded; the image is clear when viewed through the center of the lens, but it becomes distorted as one moves the image off of the optical axis. Astigmatic aberrations appear in a lens whose shape is neither properly rounded nor cylindrically symmetric. In this case, the image becomes blurred and distorted, regardless of the objecfs orientation. The two aforementioned aberrations can happen with any type of light passing through the lens, even monochromatic light Chromatic aberrations occur because of differences in wavelengths for different colors of light. Recall that in a prism, light refracts differently depending upon its wavelength. Since the focal point depends upon refraction through the lens, light of different colors refracts to different focal points. This is true for most lenses and can be seen if you look carefully at a projected image-it will have a rainbow halo around it (i.e., not every wavelength oflight has focused coherently at the viewingscreen).
258
Physics
Interference Phenomena
Interference
Interference Phenomena
If you've seen the spectrum of colors in a soap bubble, a stack of microscope slides, or an oil slick, you've seen examples of interference. The green, for example, will show brightly only in certain regions of the microscope slide. The
green regions are regions of constructive interference for green light; where green is not seen, the green interference is destructive. The same goes for every other color you see. These everyday interference patterns are seemingly random. In laboratory experiments, the interference is carefully controlled; but it still
arises for the same reasons. When two or more waves overlap in phase (e.g., crest
overlaps crest, trough overlaps trough), the interference is constructive. The regions of constructive interference are often referred to as intensity maxima. When the waves are completely out of phase (sometimes referred to as "180 out of phase"), the interference is destructive. The regions of destructive interference are often referred to as intensity minima. All other types of overlap will produce interference somewhere between these two extremes. Any wave can interfere
with another wave; but in order for the interference to be most noticeable, a few
The waves must be reasonably coherent-they must retain their periodic shape, without breaks in their phase. The waves must have the same polarizationwaves of different polarization
can never completely cancel out, since they oscillate along different axes.
These requirements are determined in Young's double-slit experiment. His experiment involved light, but we can see the same qualitative results using
water waves. Imagine two slits separated by a distance d, from which water
ripples emanate (Figure 10-19). The wave crests (black semi-circles) radiate up and hit a screen. Because any overlapping waves can interfere, the resulting waves at the screen are constructively larger when two crests overlap (or two troughs overlap). This constructive interference is noted by bright spots on the
screen and by peaks on an intensity-versus-position plot (adjacent to the screen).
screen
Figure 10-19
259
Physics
Interference Phenomena
The amplitude of these peaks typically depends upon the intensity of the waves, whereas the spacing depends upon other quantities. For example, what should happen to the peaks if the wavelength increases, but all else remains fixed? Looking at Figure 10-20, the spacing should increase (remember, the same interference rules apply, regardless of k, d, or L). What should happen if we increase d, while keeping all other variables fixed? Figure 10-21 shows that the spacing should decrease. As a quick self-quiz, sketch out what should happen if L is decreased, while holding k and d constant. You should find that the spacing decreases if L decreases. This direct proportionality between L and the maxima spacing occurs because the interference pattern has more distance over which to spread, if the screen is farther from the two slits.
screen
Figure 10-20
ii >^
screen
Figure 10-21
If we call the space between two adjacent maxima y (as in Figure 10-21), the
relation between y and the other experimental variables is expressed as:
y = VL
d
(10.13)
260
Physics
these features:
Interference Phenomena
This tells you about the interference pattern, once it occurs; but how do you
know whether a passage is asking you about interference? Look for any or all of
waves overlapping in space-regardless of their type, but typically light,
sound, or water.
For example, if you shine monochromatic laser light onto a thin film of oil as it floats on water, you see light and dark patterns. This must be an interference
effect; and because it involves a thin film of material, it is called thin-film
interference. It is this type of light interference that you see in bubbles and microscope slides. So how do the thickness of the film and its optical properties factor in? Let's answer this by asking what it takes to create constructive
interference.
Shine laser light on the oil film in Figure 10-22a. Upon hitting the oil, the light will partially reflect and partially refract (note that this is a general behavior of any wave mat hits an interface between two media). The refracted ray will
partially reflect off of the oil-water interface and subsequently return to the air. If this returning wave and the initially reflected wave are in phase, then a bright (constructive) spot results. If they are completely out of phase, then a dark spot results. Whether the waves are in or out of phase depends upon the path-length
difference fi between the two waves (i.e., the extra distance one wave has to
travel with respect to the other wave). Here, the refracted and subsequently reflected ray is the ray that travels farther. In this case, 6 should be:
5 = 2d = N(X/n)
(10.14)
where the 2d comes from the fact that one wave must travel down and back up through the oil (note that the laser wave is drawn at an angle only for the sake of clarity). The index of refraction n (of the thin film) accounts for the shorter wavelength of light within the oil than in air. The variable N is an integer, which means that some whole number of wavelengths must fit into this path-length difference, if the two waves are to be in phase upon traveling back up into the
air.
(a)
(b)
oil n = 1.25
3^#S^i
Figure 10-22
This relation does not hold for all examples of thin-film interference. A subtle complication can arise that depends upon the refractive indexes of the materials above and below the thin film. Referring to Figure 10-22b, suppose that a watery soap film (of the same thickness as the oil) is surrounded completely by air and is hit with the same light that hit the oil. In this case, the light would interfere destructively. Why?
261
Physics
Interference Phenomena
The effective path-length must be somehow different in this case-specifically, it must be half a light wavelength different, so that the two interfering waves are 180 out of phase. Why does this happen? It turns out that when a wave reflects from an optically denser medium, its phase flips 180 (i.e., a crest turns into a trough). In the case of the oil film on water, the phase flips for both the wave
that reflects off of the air-oil interface and the wave that reflects off of the oil-
water interface.In both cases, the light bounces off of a material whose refractive index n is higher than that of the material through which the wave moves. For the oil film on water, the phases of both waves flip; the effect cancels, and the waves interfere constructively. For the soap film, only one of the two reflecting waves flips its phase. This single flip effectively adds half a wavelength to the path-lengthdifference (note that 180 of phase is akin to a half- wavelength shift) and results in destructive interference. Keep in mind that the constructive and destructive interference occur in these two problems because of a specific combination of the film thickness, light wavelength, and the refractive indexes. Generally, light incident normally upon a thin film reflects constructively, if:
(10.15)
(i.e., if the effective path-length difference is an integral number of wavelengths). Identifying a thin-film problem is the same as identifying any interference problem, with the additional requirement that there be some thin film. Thin-film interference has industrial applications. Thin plastic coatings are often sprayed onto camera lenses to create an anti-reflective lens. No light reflecting means more light in through the lens. The wavelength selected to have the least reflection (e.g., yellow-green, as it is in the middle of the visible spectrum), determines the thickness of the anti-reflective coating of the lens. This coating
actsas the thin film, creating destructive interference of that specific wavelength.
Thin-filminterference is used to size small objects (e.g., objects whose diameters are only a few microns across). If a hair is sandwiched between two microscope slides, there will be a thin, wedge-shaped film of air between the slides (as in Example 10.12b). Laser light shining on this film interferes constructively or destructively, as the thickness of the film varies across the slides. The distance
between the constructive interference zones allows us to find the size of the hair.
Example 10.11a
A. B. C. D.
Decreasing the slit separationby a factor of 4. Increasing the distance betweenthe slits and viewing screenby a factor of4. Increasing the wavelength of the light by a factor of 4. All changeswill spread the maximaby the same amount.
Solution
Increasing the wavelength of the lightby a factor of 4 will increase the separation distance by a factor of 4. All of the changes result in an increase in the distance between maxima by a factor of 4, so all of the changes are equal.
The best answer is choice D.
262
Physics
Example 10.11b
Interference Phenomena
When laser light is sent through two slits, a periodic pattern of constructive and destructive spots appears on a distant viewing screen. Suppose the two slits are now replaced with a diffraction grating (essentially several slits), as shown in the diagram below. If the same total light intensity is used in both the double- slit and the diffraction grating experiments, then the bright spots of the interference pattern in the diffraction grating experiment will be:
screen
ii
izzi c=] cz] rzzi czi nzn ezd izzi rzz] czi tzzi czi izzi nn ir
A. more intense and spaced together more closely than in the double-slit
experiment.
B. more intense and spaced farther apart than in the double-slit experiment. C. less intense and spaced together more closely than in the double-slit
experiment.
D. less intense and spaced farther apart than in the double-slit experiment.
Solution
The image may not be drawn to scale, so simply comparing this image with that of Figure 10-19 will not answer the question; we need to consider the effects on the intensity and maxima spacing more generally. Without going into depth, we know that a fixed amount of light should reach the screen, so if the number of spotsdecreases, the intensity of each remaining spot should increase. This makes choices C and D highly unlikely answers. The maxima appear at the screen when light from all the slits are constructively interfering. In Young's experiment, there are only two slits whose light must interfere constructively. The maxima, therefore, appear periodically across the screen, whenever the path-length difference between the two light rays is equal to some integral number of wavelengths. With a diffraction grating, the constructive spots will, again, appear when the light rays from all slits are interfering as constructively as they
can. Since the light rays emanating from several slits must now interfere in
phase, the likelihood of a maximum is much smaller than it is in the double-slit experiment. Therefore, the spacing between maxima must be larger with the
diffraction grating; this rules out choices A and C.
The diffraction grating maxima will also be much narrower than the double-slit maxima. Regarding the intensity, we know that a bright spot at the screen must occur because several light paths are constructively interfering. Since "several" is a bigger number than two (as in the double-slit experiment) and because the maxima are now much narrower, the maxima intensity must be greater for the
diffraction grating experiment.
The best answer is choice B.
263
Physi CS
Interference Phenomena
Example 10.12a
A thin hair is placed between two microscope slides (n = 1.5), as shown. When laser light is shined down onto the slides, periodic intensity maxima are seen to span the slides. Which of the following changes will decrease the distance
between the maxima?
top view
IBII^x
hair
side view
I. Decrease the wavelength of the laser light. II. Fill the air gap between the slides with carbon disulfide (n = 1.6). III. Move the hair to the left, while keeping the slides in contact with each other at their left edges.
A. B. C. D. I only I and m only Hand III only Ill only
Solution
A shorter wavelength will decrease the distance between adjacent maxima. This is shown in equations (10.13) and (10.14). This makes Statement I valid. Filling the gap with carbon disulfide, as opposed to air, would lead to a smaller difference between the index of refraction of the medium and that of the glass. A smaller difference in n values results in less bending of light, so the light would need to travel farther to get the same maxima as it got when air filled the gaps. This would spread the bright spots, thereby increasing the distance between adjacent maxima. Statement II is invalid. For Statement III, it is perhaps best to visualize what happens when the hair is moved to either the left or right. If the hair moves to the left, then the glass slides grow farther apart. If the hair moves to the right, then the glassslidesgrow closertogether.Taken to an extreme, if the two slides touch one another, then all of the bright spots are gone (pushed offof the plate if you will). Opening the gap creates the spots and closing the gap eliminates the spots, so widening the gap must bring adjacent maxima closer
together. This makes Statement III a valid statement.
The best answer is choice B.
Example 10.12b
A thin layer of plastic (n = 1.46) coats the surface of a glassplate (n = 1.52). When monochromatic light is shined normally onto the plastic from the air above,
constructive interference occurs. Destructive interference will occur when the
A. B. C. D.
264
Physics
Solution
Interference Phenomena
The system involves light traveling from air (n = 1) to plastic (n = 1.46) to glass (n = 1.52). Since only the medium above the plastic changes (and not the thickness of the plastic itself)/ a change from constructive to destructive interference must relate to phase flips. Phase flips of the light occur when the light bounces off of a medium whose refractive index exceeds that of the medium through which the light passes. In the original constructive set-up, light bounces off of an air-plastic interface and a plastic-glass interface. For both reflections, the refractive index of the reflecting medium is greater than that of the medium through which the light passes. For both reflections, the phase of the light will flip by 180. To get destructive interference, we would need to change the experiment such that one of these two phase flips does not occur. If this is achieved, the single-phase flip would lead to destructive (i.e., 180 out-of-phase) interference between the two final rays. Since the plastic-glass interface is fixed (no choice allows us to change it), we must get rid of the phase flip at the air-plastic interface. To do so, we select a liquid whose refractive index is greater than that of the reflecting plastic
(greater than n = 1.46). Benzene is the only liquid with this property, making
choice D correct. As an aside, notice that water will not change the constructive
interference, because it is less optically dense than the plastic (i.e., a phase flip will occur at the water-plastic interface). Carbon tetrachloride will lead to only one reflection, at the plastic glass interface. There will be no reflection at the carbon tetracnloride-plastic interface, because they have the same refractive index (i.e., there will be no optical interface for the purposes of reflection and refraction); this phenomenon is known as index matching, and it is useful in
Diffraction
Light passing through the slits and gratings that we have been discussing spreads out as it makes its way to the screen. You don't see this spreading, however, when you view light passing through your window. The light strikes the floor, making a pattern of the window. So, when and why does a wave spread? Light waves, orany type ofwave, always bend and distort when passing through an opening or around an object. This distortion is known as diffraction.
Diffraction is most noticeable in everyday life when watching water waves pass
by some obstacle. In Figures 10-23a and Figures 10-23b, two different waves (viewed from above) passthrough thesame opening. When the opening is much larger than the wavelength, the wave doesn't distort much; when the opening is smaller than the wavelength or is of comparable size, the wave spreads out
noticeably.
(a)
I Intensity
Figure 10-23
*| Intensity
265
PhysiCS
Interference Phenomena
The general relation is this: Diffraction is more significant when the wavelength is smaller than or comparable to the opening the wave crosses; diffraction is less significant (or negligible) when the wavelength is much smaller than the opening. This applies to all waves. So why do the light waves entering your room through the window not spread much? Their wavelength is much smaller than the window. Why do sound waves spread so effectively when entering through that same window? The wavelength of the typical sound wave is on the order of a meter-close to the size of the window. In Young's experiment, the wavelengthwas close to that of the slit widths. This is why the light spread after passing through the slits. The light does more than simply spread-it also gives rise to interference patterns. Since there is no other wave with which it can diffract, you could say that diffraction is a form of "self-interference." The patterns at the screens result
from the water waves in Figure 10-23a and Figure 10-23b. The pattern is
represented by a plot of intensity vs. position on the screen. Notice that there is a relatively bright (i.e., high intensity) central maximum, and some much smaller
maxima to its sides. These result from self-interference. Notice also that when the
wave spreads more, so does the resulting diffraction pattern. Diffraction patterns still occur in the absence of significant spreading-they are just much harder to
see, due to the relatively weak intensities of the side maxima.
How does the width of this central maximum relate to the wavelength of the
effect, the width should relate to these parameters in the same way as tiie
increased wavelength would increase the diffractive spreading, and therefore increase the width of the diffraction pattern at the screen. Likewise, moving the screen away from the slits would increase the width of the diffraction pattern, because thediffracted wave has more distance overwhich tospread out.
Example 10.13a
wave and to the distance separating the slit and screen? As this is an interference
when incandescent light is sent through the same slit. Laser light is fairly
a small opening forms definite diffraction patterns; such patterns are not seen
Whenever you've seen examples of light diffraction (presumably insome physics lab), you probably used a laser to generate the light. Laser light shining through
monochromatic (i.e., of one wavelength) and coherent. With these facts in mind, choices A through C are not good choices. Only choice D, which is close to the
type of light an incandescent bulb emits, would make diffraction less noticeable.
Remember, diffraction is an interference effect ("self-interference," if you will). Therefore, anything that makes interference more pronounced (e.g.,
they say the same thing.
monochromatic, coherent light of one polarization) would make diffraction more pronounced. You could have ruled out choices A and B immediately, because
266
I.
II.
III.
Prism Dispersion
Interference
The main purpose of this 25-question set is to serve as a review of the material presented in the chapter. Do not worry about the timing for these questions. Focus on learning. Once you complete these questions, grade them using the answer key. For any question you missed, repeat it and write down your thought process. Then grade the questions you repeated and thoroughly read the answer explanation. Compare your thought process to the answer explanation and assess whether you missed the question because of a careless error (such as misreading the question), because of an error in reasoning, or because you were missing information. Your goal is to fill in any informational gaps and solidify your reasoning before you begin your practice exam for this section. Preparing for the MCAT is best done in stages. This first stage is meant to help you evaluate how well you know this subject matter.
^^
Passage I (Questions 1 - 7)
3.
Students in a physics laboratory conduct a simple experiment with a converging lens. An object is placed at a distance d to the left of the lens. Its focused image is projected onto a screen to the right of the lens. For this particularexperiment, the image formed at a distance of 2d to the right of the lens, as depicted in Figure 1:
Thin lens
Screen
A. I
2
B.
C. V2
D. 2
4.
Suppose that the object in Figure 1 were moved to the left, and that d > f throughout the moving process. To
keep the image on the screen, the screen would have to
be:
For lenses and mirrors, the image distance and object distance arerelated by the thin-lens equation:
L + L = L,
i o f
5.
Ifthe lens has a focal length of d/2, how far away from
the lens should we place the screen?
A. d/2 B. 2d/3
C. d 2d D.
1.
B. ^
3
6.
Suppose that the converging lens were replaced with a diverging lens of focal length -2d. The image would
then be:
C. D.
d 2d
7.
Suppose that the lens in Figure 1 had a focal length d. How far to the left of the lens should the object be placed to get an unmagnified, real image?
A. B. 4d 2d
C.
d
2
D. d
268
Passage II (Questions 8-14) When white light passes through a prism, light rays of each color are refracted (bent) by different amounts to produce different angles of deviation. Red light is refracted the least by a prism. The refraction process through a prism
is demonstrated in Figure 1.
Red
9.
A. B. C. D.
The greater its frequency, the less it is refracted. The longer its wavelength, the more it is refracted. The shorter its wavelength, the more it is refracted. The greater its energy, the less it is refracted.
Orange
Yellow Green Blue Violet
10. Which kind of light will bend the MOST when passing
through these prisms?
A. B. C. D.
Green light passing through dense flint. Violet light passing through crown glass. Red light passing through ice. Blue light passing through quartz.
This dispersion of light is seen in various solids. The refractive index determines the amount of spreading. As the refractive index increases, the degree of refracting increases. The refractive indexes for six different wavelengths of light
in six different solids are shown in Table 1. Material
Violet Blue
A. The colors disperse less, but they stay separate. B. The colors disperse less, and they recombine to
become white light.
C. The colors disperse more, and they stay separate. D. The colors disperse more, and they recombine to
become white light.
Green
Yellow
Orange
1.522 1.587 1.665 1.543
Red
1.526
1.523 1.588
1.667
12. Two identically shaped prisms are juxtaposed as shown below. Violet light exits the system above red light,
because the average index of refraction of Prism II is: White
violet
Quartz
Diamond Ice
1.544 2.417
1.309
1.542
2.410 1.306
2.458
1.317
2.415
1.308
Table 1
In a vacuum,
all light waves-regardless of their A. less than Prism I; light is dispersed more in Prism I. B. C. D.
13.
Which of the following kinds of light will travel at the GREATEST speed? A. B. C. D. Violet light passing through air Blue light passing through water Yellow light passing through a vacuum Orange light passing through kerosene
14.
What is true of different colors of light in a medium? A. B. C. D. As As As As frequency increases, the energy decreases. wavelength increases, the energy increases. speed decreases, the wavelength decreases. frequency increases, the wavelength decreases.
269
light passes through two narrow slits that are close together and falls on a screen, forming a series of bright and dark bands (fringes). A schematic of a double-slit apparatus is
shown in Figure 1:
relative
intensity
at screen
Figure 2
by thin films. Light is reflected from the front and back surfaces of the film. The light reflected off of the back
Light rays (e.g., Rays 1 and 2) passing through each slit generally travel different distances to reach the same point on the viewing screen. Because path-length differences yield phase differences (between the two lightrays striking a point
on the screen), various degrees of constructive or destructive
surface of the film has a longer path to travel than the light reflected off of the front of the film. Again, this path-length difference leads to phase differences, depending on the thickness of the film, the angle at which the light falls on the film, and also the refractive properties of the space
surrounding the film.
15.
interference arise. These constructive and destructive regions are the brightand darkfringes, respectively. The criterion for constructive interference is that the path-length difference must equal a multiple of the wavelength of theincident light.
Quantitatively, this is written as:
m k = d sin 0
sometimes called the order, mX is thepath-length difference. For destructive interference, the path-length difference must equal a multiple of halfthe wavelength of the incident light.
Thus:
(m +1) k = d sin 6
2
essentially in the same way as two slits do. The gratings, however, produce fewer bright spots for a given incident light intensity than a double-slit set-up does. Each bright fringe also subtends a smaller angular range than its doubleslit counterpart The formula for determining the primary
brightfringes in a diffraction grating is:
m k = d sin 9
16. Certain colors observed in natural materials are produced by thin-film interference, while most are the
result of absorption. Differentiating one effectfrom the other can be done MOSTeasily by:
B. observing the light exiting the sample through a prism, set at a fixed angle with respect to the
material's surface.
sometimes called the order, mX is thepath-length difference. For destructive interference, the path-length difference must equal a multiple of halfthe wavelength of the incident light.
Thus:
C. observing the light exiting the sample through a polarizer, set at a fixed angle with respect to the
material's surface.
270
17. If we compare the bright fringes produced by a doubleslit apparatus and a diffraction grating, we find that the fringes produced by:
A. both experiments have similar intensity and similar
width.
B. the double-slit apparatus have a greater intensity; the fringes for both have a similar width. C. the diffraction grating have a greater intensity; the fringes for the diffraction grating are narrower. D. the diffraction grating have a greater intensity; the fringes for the double-slit apparatus are narrower.
18.
If the double-slit apparatus is placed under water and the same light is used, the bright fringes will: A. now be closer together. B. now be farther apart.
C. remain at the same locations.
D.
23.
What happens to parallel light rays coming from the left, and then traveling through a diverging lens?
A. They are directed through the focal point to the left
of the lens.
19.
B. They bend away from the center of the lens, appearing to have come from the focal point to the
left of the lens.
C. They bend towards the center of the lens, traveling through the focal point to the right of the lens. D. They bend away from the center of the lens, appearing to have come from the focal point to the right of the lens.
20.
A diffraction grating with 8000 lines/cm is illuminated with white light What is the spectrum of the HIGHEST
order (i.e., maximum value of m) that includes any
24.
Which of the following equations can be used to determine the critical angle?
C.
D.
3
4
'"material
21.
The effects of passing monochromatic light through a single-slit apparatus are fundamentally different from the effects of passing monochromatic light through a double-slit apparatus. This statement is: A. true; light from two slits can interfere with itself, whereas light from a single slit has no other wave
to interfere with it.
B.
C.
25.
A. 500-nm light waves through a one-meter hole. B. 500-nm light waves through a one-centimeter hole.
C. 5-mm ultrasonic waves through a one-meter hole. D. 5-mm ultrasonic waves through a one-centimeter
hole.
D.
false; both effects are fundamentally the same, true, but only as long as we use monochromatic light. It is false, if we use light of several frequencies. true, but only as long as we do not consider a double-slit apparatus as an apparatus with two single slits.
1.
2. A
3. D 8
B
4. A
5. C
10. A
6. D
7.
12. 17.
B
D
9.
11. C 16. A
21.
13. C 18. A
23. B
14. D 19.
B
15. D
20. C
22. D
24. A
25. D
271
Choice B is the best answer. The quickest way to get the focal length of the lens is to use the thin lens equation given in the
passage. Since the clear image is on the screen, the image distance is the same as the screen distance.
1 +1 = 1
of
>
1_ + 1 = 1
2ddf
=>
_3_ = 1
2df
=*
f = 2d
3
You may also have noted that in order for the image to project onto the screen, it must be a real image. With a convex (converging) lens, the object must be outside of the focal length in order to create a real image, so choices C and D are not
possible. The best answer is choice B.
Choice A is the best answer. The choices are linear or possibly exponential, with either an increasing or decreasing relationship. As an object gets closer to the lens, the image gets farther away from the lens, so the graph should express a
decreasing relationship. This eliminates choices B and D. The thin-lens equation is:
1 + 1 =1
i o f
Rearranging gives:
1=.1+1
This has the form y=mx + b, with y=-1, x=1, m=-1, and b=1. So the graph of 1 versus 1 is a straight line with a
i negative slope. The best answer is choice A. o f o i
3.
Choice Dis the bestanswer. Themagnification for lenses and mirrors is given by:
M = ^i- = --L
M = - 2d = .2
Since the magnitude ofthe magnification was asked for, all we have to do is take the absolute value ofM. Thus, we get M=
2. The best answer is choice D.
Choice A is the best answer. As the object moves farther away from the converging lens, the image gets closer to the focal point of the lens. As alimiting case, ifthe object were to be moved infinitely far from the lens, the image would be exactly at a focal point. This means that the image will move closer to the lens as the object moves away from the lens; we must
therefore move the screen to the left (i.e., closer to the lens). The best answer is choice A.
1 = -1 + 1 =
1 +2 = 1
d d d
i = d
6.
Choice Dis the best answer. The fastest way to the solution is to use the thin-lens equation:
1 +1 = 1
i o f
1 = -1 + 1 = -l.J_ = -J_
i of d 2d 2d
= -2d
3
The negative sign on i means the image is virtual. For lenses, a virtual image is always on the same side of the lens as the
object This means that the imageis virtual and to the leftof the lens. The best answer is choice D.
7.
Choice Bis the best answer. We want the magnification equal to -1 instead of+1, because a real image in this case would
be inverted.
M = -io
1 = -Jo
1 +1 = 1
2=1
o d
o =
2d
272
MINI-TEST EXPLANATIONS
Prism Dispersion
Choice B is the best answer. Choice A should be eliminated, because if the light rays of different colors in sunlight traveled at drastically different speeds, then the fastest constituent color of light would be the first to appear. Choice C should be
eliminated, because all light rays travel at the same speed through a vacuum (2.98 x 10^ m/s). Choice D should be
eliminated, because rays of white light (comprising all colors) leave the Sun at the same time. Choice D is downright loony! Choice B is the best answer, because after the different colors of light enter the atmosphere, they travel to the surface of the
Earth at roughly the same speed, allowing the arrival of all of the colors to appear to be simultaneous. The best answer is
choice B.
9.
Choice C is the best answer. Figure 1 shows that violet light is refracted by the greatest amount for light in the visible range
of the EM spectrum. The data in Table 1 confirm that violet light has the largest index of refraction in all six media, so violet light is refracted by the greatest amount in all six media. Violet light has the highest frequency, shortest wavelength, and
greatest energy of any color of visible light. This means that greater frequency results in greater refraction, eliminating
choice A. The shorter the wavelength of visible light, the more it is refracted, which eliminates choice B and makes choice C the best answer. The greater the energy of light, the greater its frequency, and the more it is refracted, so choice D is
eliminated. The best answer is choice C.
10.
Choice A is the best answer. The greatest degree of bending will be experienced by the light-and-medium combination possessing the greatest index of refraction. This can be read directly from Table 1. Green light passing through dense flint has an index of refraction of 1.674. Violet light passing through crown glass has an index of refraction of 1.538. Red light passing through ice has an index of refraction of 1.306. Blue light passing through quartz has an index of refraction of 1.551. The greatest index of refraction among the choices given is green light passing through dense flint. The best answer is
choice A.
11.
Choice C is the best answer. As the incident angle increases, the amount of refraction at the first interface increasesremember: a bigger incident angle correlates to a bigger refracted angle. This increases the spread of the various light rays as
they pass through the prism and also increases the refracted angles at the second interface in the prism; dispersion is even greater. If the beams are dispersed more, they probably will not come back together at any point in space. The best answer is
choice C.
12.
Choice D is the best answer. The light must be tracked step by step to grasp what is occurring in the double-prism system. White light passing through the first prism is refracted so that violet light exits at the greatest angle, making it the lowest beam as it leaves the first prism. Passing through the second prism, violet light is again refracted to the greatest degree, but now it is refracted in the opposite direction (up rather than down, because the angle of the interface is different than the first interface). The degree of refraction must greater in Prism II than in Prism I, to explain why the violet light crossed over the
red light, and exited above the red light, as shown in the picture. That means Prism II must have a greater index of refraction than Prism I, causing light to be more dispersed in Prism II than in Prism I. This makes choice D the best answer. Note that the incident angle is close to the exiting angle, meaning that despite the difference in dispersion in the two prisms, the deviation of each prism is approximately the same and the plane through which the light first enters into Prism I is parallel to the plane through which the light exits from Prism II. The best answer is choice D. 13. Choice C is the best answer. All light in a vacuum has the same speed, regardless of color (wavelength). In addition, light travels more slowly in a medium than in a vacuum. This means that the greatest speed is experienced by the light in a vacuum, making choice C the best answer.The fact that the light is yellow is irrelevant in this question. Where the color does become important is when we compare light rays passing through thesame medium. In that case, the light ray with the longer wavelength travels faster. The best answer is choice C. Choice D is the best answer. The energy, wavelength, and frequency of light are related according to the following
equation:
14.
E = h/ = h^-,
k
where E is energy, h is Planck's constant, / is frequency, c is speed, and k is wavelength. According to the equation, as frequency increases, the energy of the light increases, eliminating choice A. As wavelength increases, the energy of the light
decreases, eliminating choice B.
There is no distinct relationship between speed and wavelength. Within a vacuum, all light has the same speed, regardless of its wavelength. While this does not eliminate choice C beyond doubt, it does not mandate our selection of it as the best answer, either. As frequency increases, the wavelength of the light decreases. The best answer is choice D.
273
MINI-TEST EXPLANATIONS
Interference
15. Choice D is the best answer. Diffraction effects do exist for each of the two single slits-that is why the light spreads out from each slit in the first place. Such effects are more noticeable when the slit size is smaller than the wavelength of the incident light (although diffraction is still observed when the slit size is comparable to the wavelength). Requirements relating to the slit separation d are irrelevant, because if the aforementioned requirement is not met, then there can be no light
spreading and, therefore, no interference between light from the two slits. This eliminates choices B and C. The best answer
is choice D. 16.
Choice A is the best answer. As mentioned in the passage, the path difference is dependent on the angle at which the light
strikes and exits the film. Observing the exiting light from different angles, with respect to the material's surface, would
change this path difference. This is basically saying that as the angle changes, the distance is different, because the diagonal pathway traversed changes. This, in turn, changes which wavelengths of light constructively interfere with each other (i.e., it changes the observed colors). Choice B is incorrect, because the prism refracts only light exiting the sample; it does not change the color of this light. Choice C is incorrect: A polarizer polarizes only the exiting light, and it does not change its
color. The intensity of the light may drop, which will impact the color's brightness, but it will nonetheless be the same colorof
light. The best answer is choice A.
17.
Choice C is the best answer. As mentioned in the passage, fewer bright spots are seen when using a diffraction grating than when using the double slit-apparatus, for the same intensity ofincident light. Since the same incident intensity makes up the bright spots in both cases, the bright spots must be brighter for the diffraction grating-after all, there are fewer spots having the same total energy as the many more spots in the double-slit setup. This rules out choices Aand B. To see why choice Cis
correct, recall that the passage states that the diffraction grating spots subtend a smaller angle than those of the double-slits.
This means that diffraction grating spots are narrower than those produced by a double-slit setup. This happens because a
gratings have many more than two slits, constructive interference is less likely to occur. A bright spot would not be spread over much of the screen, because any spreading quickly reduces the chance that all slits are interfering constructively. The
double-slit apparatus requires only that two slits interfere constructively; this relaxed requirement also relaxes the narrowness
of the bright fringes. The best answer is choice C.
18.
bright spot occurs when light rays from all the slits are constructively interfering at that region of the screen. Since diffraction
Choice A is the best answer. When the double-slit setup is placed under water, the wavelength ofthe light is reduced. This is
because water has a higher index of refraction than air, so light travels more slowly in water than it travels in air. If the wave speed of the light is reduced, then the wavelength is also reduced. The frequency of the light remains the same, because the
frequency is determined by the source. The spacing of the bright fringes is determined by the wavelength, according to:
m k = d sin0.
According to the relationship, as the wavelength gets smaller, 0also gets smaller, so the bright fringes will be spaced closer together. This makes choice Athe best answer of the four choices. Choice Dis incorrect: Although the bright and dark fringes shift, they do not necessarily shift in such a way as to replace the bright fringes (observed when the experiment is done in air) with dark fringes (observed when it is done under water). Choice Cshould have been eliminated immediately, because adding the experiment to water changes the wavelength of the light, so some change in the interference pattern will be observed. The
best answer is choice A.
19.
reflects off of the front of the soap film and the wave that reflects off of the back of the soap film). As the soap film evaporates over time, the thickness of the soap film changes (perhaps getting thicker or getting thinner). This change in soap film
ones that are adding constructively. Choices Aand Care incorrect, because choice Cis saying essentially the same thing as choice A, a refractive effect-it occurs when the index of refraction for a material varies with the wavelength of light. When
two answer choices are fundamentally the same from a physical point of view, those two choices are usually both wrong, and
a question is asking, but you recognize that two answer choices are saying essentially the same thing. Choice D is incorrect,
change much with time. The best answer is choice B.
Choice Bis the best answer. Constructive interference is based on a path difference traveled by the two waves (the wave that
thickness in turn changes the path difference for the two waves, so as the soap film evaporates, different colors will be the
thus should both be eliminated. This can prove useful when speeding through questions or when you aren't quite certainwhat because the wavelengths of light that are selectively absorbed by amaterial (assuming absorption is significant) depend upon
the molecular makeup of the material. Since this makeup does not change much with time, the colors absorbed should not
274
MINI-TEST EXPLANATIONS
20.
Choice C is the best answer. To solve for the largest m that includes any portion of the visible spectrum, we must use the
equation given in the passage: mk = d sin8. Upon manipulating the equation to isolate the m, we arrive at the following
relationship:
m _ dsinO
where d = 1/8000 lines/cm. The wavelength of visible light ranges from roughly 400 nm to roughly 700 nm. Since we want the largest m, we choose the smallest wavelength and the largest sin 0~these numbers are 400 and 1, respectively. Solving
form:
10'
10'
100 32
8000 x 400
32 x 105
The value of m has to be an integer, so we must approximate the answer as 3, because it is the closest of the choices to
100/32. The best answer is choice C.
21.
Choice B is the best answer. Although we speak of single-slit effects and double-slit effects, both effects are the result of
wave superposition-constructive and destructive interference. This means that the effects of passing monochromatic light through a single-slit are not fundamentally different from passing monochromatic light through a double-slit. Choice A is incorrect: Light from a single slit interferes with itself. Choice C is incorrect: Light with several frequencies will still display interference effects, although we may not always be able to see them as sharply. Choice D is incorrect: A double-slit is two single slits. It is possible to speak of single-slit and double-slit effects in the same experiment; for certain experimental conditions, it is possible to see single-slit diffraction patterns within the double-slit interference pattern. This will occur when the slit width and the wavelength of monochromatic light are chosen in such way where fringe interference occurs at different points than the bright spots of the double-slit interference. The best answer is choice B.
Questions 22 - 25
22.
Choice D is the best answer. Total internal reflection can occur only when a wave is moving from a region with a higher index of refraction to one with a lower index of refraction, because the ray will bend away from the normal. This occurs
when light is traveling from a slower medium into a faster medium (as we see when light travels from water into air). None of the Options I, II, or III corresponds to a situation where light is traveling from a slower medium to a faster medium. Light is faster in a vacuum than it is in air, light is faster in air than in glass, and light is faster in glass than plastic. Unnerving as it might be to choose, the best answer is none of the above, choice D. Although "none of the above" is rarely an answer choice, if it does happen to be a choice on your actual MCAT, treat it as just another answer and squelch any bias or preconceived notions you may have about choosing such an answer. The best answer is choice D. 23. Choice B is the best answer. First off, a converging lens focuses parallel light rays that pass through it toward the focal
point of the lens. This is how the lenses in cameras, microscopes, and reading glasses work. However, light rays coming toward and then passing through a diverging lens diverge away from the center of the lens. This fact immediately eliminates choice C. This is something you should have committed to memory as both a informational fact as well as a mental visualization. Choice A is also obviously incorrect, because if light rays were coming in parallel to each other, why would they all bend and go through the first focal point before ever even coming into contact with the lens? If they haven't yet interacted with the lens, then they would not undergo any sort of bending due to the lens. That leaves us with choices B and D. The only difference between the two is that in choice B the light rays appear to have come from the first focal point, and in choice D, they appear to have come from the secondfocal point. Imaginea ray diagram for a typical diverging lens: If the rays appearto come from the second focal point, then they would have to be refracted by more than ninety degrees. Since we know that this is physically impossible, the light rays must appear to come from the first focal point This is why we extend our dashed line in ray diagrams back to the first focal point, using the straight lines associated with the diverging rays leaving
the lens. The best answer is choice B.
24.
Choice A is the best answer. When dealing with a critical angle, vve are considering a refracted angle of 90. If you look at the answer choices, you'll notice that this question requires that you manipulate Snell's law for a refracted angle of 90. Because sin 90 is 1, the sine 90 term drops out of the calculation, leaving just n on that side of Snell's relationship. The result is that the sine of the critical angle equals the ratio of the medium with the lower index of refraction to the medium
with the higher index of refraction. The math is as follows:
275
MINI-TEST EXPLANATIONS
25.
Choice D is the best answer. Wave diffraction is most pronounced when the wavelength of thewaves passing through a slit
are comparable to the diameter of the slit Of the answerchoices, 5 millimeters is relatively close to 1 centimeter(it is half as
large), so that is the scenario with the greatest observed amount of diffraction. The best answer is choice D.
276
MINI-TEST EXPLANATIONS
I.
II.
(1-6)
III.
Telescopes
42-52
34-41
24-33
17-23
1-16
1-3
Passage I (Questions 1 - 6)
To study the refractive properties of a series of materials, light of 589 nm (from a yellow sodium lamp) was used. The light was transmitted through a half-cylinder disk of the material at gradually increasing incident angles until no light
3.
left the material from the flat surface to the air. For light that
transmitted from flat face of the half-disk to the air, the beam
was allowed to strike a semi-circular screen. For each of the
A. B. C. D.
transparent to visible light. of uniform composition. at a uniform temperature. absorbing of light at 589 nm.
light rays that left the middle of the flat face of the half-disk, the point of highest intensity against the screen was recorded. The path of the light was traced back to determine the
4.
Which of the following explanations supports the notion that monochromatic light is essential for the
experiment to work?
Incident ray
of589nm,<
Point a
Half-disk of Material
Screen
42.2
40.4 31.3
B. does not leave the half-cylinder disk. C. splits to strike the screen at multiple points.
D. slows when leaving the disk and entering air.
6.
If this experiment were carried out in water instead of air, what would be expected?
What is the refracted angle for yellow light passing from air into a rectangular block of flint glass with an
incident angle of 60?
A.
B. C. D.
0
32.1
B. The critical angle would be smaller in water than air; the angle of refraction would be smaller in
water than air.
38.1' 90
C. The critical angle would be greater in water than air; the angle of refraction would be greater in
water than air.
2.
For four lenses of identical dimensions, which material would generate the focal point closest to the lens? A. Polystyrene
B. C.
D.
278
9.
A mirroris a device that focuses light rays by reflecting them to a point Mirrors can be planar (such as the mirror that
hangs in a bathroom) or spherical (such as the front and back of a metallic spoon). Images in planar mirrors are always the
same size as the object whose light they reflect. Spherical mirrors can be either convex or concave, depending on the curvature of the mirror. A convex spherical mirror is also known as a diverging mirror. Light rays striking the surface
of a diverging mirror are reflected away from its axis. These light rays never actually meet, but they appear to meet A concave spherical mirror is also known as a converging mirror. Light rays striking the surface of a converging mirror are reflected toward its axis, so the rays actually do meet. Images in spherical mirrors may be enlarged or reduced as well as inverted or upright
The object distance (s), image distance (s'), and focal length (f) of a spherical mirror are governed by the thin lens equation:
I - I +l
f
7.
C. the density of the reflective material. D. the compressibility of the reflective material.
s'
Using a plane mirror that is 1 meter tall would prevent which standing person from seeing approximately their entire body length?
A. A person standing 1 m from the mirror whose height is 2 meters. B. A person standing 2 m from the mirror whose height is 1 meter.
11. For parallel rays of white light incident on a spherical mirror, the light's color components have focal lengths
that:
A. B. C. D.
are independent of the component frequency. increase as the component frequency increases. decrease as the component frequency increases. increase as the component frequency increases, for concave mirrors only; convex mirrors would yield the inverse relationship between focal length and
frequency.
8.
I. Both mirrors form only virtual images of an object. II. Both mirrors can form images of an object that are smaller than the object. III. Both mirrors form images of an object that are closer to the mirror than the object.
A. B. C. D. I only I and II only I and III only II and III only
12.
B. C.
D.
decreases, while the mirror remains the same. increases, while the mirror remains the same.
and mirror both remain the same.
279
14. What must be true of the relative sizes of refracting and reflecting telescopes? A. Refracting telescopes are larger, because the
objective must be small.
A. at the position of the image I of the objective. B. at the position of the objective. C. necessarily exactly between the objective and
ocular.
Figure 1
The magnitude of the telescope's angular magnification, M, is equal to the ratio of the focal length of the objective to the focal length of the eyepiece. The calculation of M is
shown below:
16.
When comparing the focal lengths of the two lenses in a refracting telescope to the telescope's length, we find
that:
M=
0
A.
B.
C.
*/ h y'/r, 7i
bothfocal lengthsare shorter than the telescope, bothfocal lengthsare longer than the telescope, the objective's focal length is longer than the telescope; the ocular's focal length is shorter than
the telescope.
f\
'*
D.
In reflecting telescopes, the other broad category of telescopes,a large concave mirror replaces the comparatively smaller objective of the refracting telescope. The mirror reflects the image to a smaller plane mirror, which reflects the image to the eyepiece. There are three types of focus used in reflecting telescopes: prime focus, Newtonian focus, and Cassegrainian focus. In telescopes with prime focus, there is no second plane mirror, and the eyepiece actually sits in the path of the light. The eyepiece is arranged differently with
respect to the mirrors.
the objective's focal length is shorter than the telescope; the ocular's focal length is longer than the telescope.
17.
280
21.
A. increase the focal length of the lens relative to air. B. decrease the focal length of the lens relative to air.
18.
In any compound lens, the image of the first lens will serve as the object of the second lens. Which of the following statements) is/are TRUE regarding the image created by the first lens?
C. I and HI only
D. I, II, and III
19.
Where will the image form when an object is placed 15 cm to the left of a concave mirror that has a focal length
of 12 cm?
A.
B.
C.
D.
20.
B. C. D.
281
24.
When the ciliary muscles of the eye contract, which of the following statements are true? I. The eye assumes a more rounded shape.
II. The eye assumes a less rounded shape. III. The focal length of the eye decreases. IV. The focal length of the eye increases. A. B. C. D. I and III only II and IV only I and IV only I, III, and IV only
of curvature and the highest index of refraction of all of the transparent constituents of the eye. The cornea covers a transparent bulge on the eye. The amount of light that actually enters the eye is regulated by the iris, a colored ring behind the cornea. The iris can adjust its size, controlling the amount of light that enters the pupil. Behind the iris is the lens, whose shape is controlled by the ciliary muscles. When the ciliary muscles contract, the lens becomes more round, thus bending light rays more.
Between the cornea and the lens is a fluid called the
25.
the cones, nerve cells that are sensitive to light and respond by generating electrical impulses. Defects in vision, such as nearsightedness and farsightedness are caused by aberrations in the eye system. Nearsightedness means that a person is able to focus clearly on objects that are close to the eye, while a farsighted person can only focus clearly on objects at a great distance from the
eye.
22. If a normal human eye were focusing on an object 2 meters away, what would be the effective focal length of the eye?
A. B. C. D. 0.002 meters 0.04 meters 0.01 meters 0.02 meters
27. The index of refraction of most materials is inversely proportional to the wavelength of light Given that the eye has evolved so that yellow light focuses on the retina, where would you expect blue light to focus?
A. In front of the retina Behind the retina On the retina
On the cornea
23.
Farsightedness could be attributed to which of the following defects within the eye?
I. Cornea too curved.
B. C.
D.
II. Cornea not curved enough. III. Ciliary muscles not able to contract. IV. Ciliary muscles not able to relax. A. B. C. D. I and III only II and III only I and IV only II and IV only
282 GO ON TO THE NEXT PAGE
Passage V (Questions 28 - 32) A lens is a piece of transparent material that focuses light to produce an image. This focusing process makes use of the fact that light is refracted twice when it passes through a lens. The focal length of a lens is a measure of how much the light rays are bent. A lens with short focal length bends the light rays to a greater extent than a lens with a long focal length.
A lens can either be converging or diverging, depending how it bends light rays that pass through it A converging (or convex) lens bends light rays toward the axis of the lens. The light rays passing through a converging lens will actually meet at a point. Converging lenses can produce either real images (the light rays really do meet at some point) or virtual images (the light rays only appear to meet at a particular point). A diverging (or concave) lens is one that bends light rays away from the axis of the lens. The light rays will never actually meet any place; diverging lenses can only produce virtual images. The thin lens equation governs the relationship between the focal length of a lens, object distance, and image
distance:
1 =1 + 1
f o i
the object and i is the distance from the lens to the image.
Lenses can magnify an object's size. Magnification relates the dimensions of the image to the dimensions of the
object and can be written as:
M = iL=.l
h o
Light must travel through lens 1 and form an image before it travels through the second lens.
where h' is the height of the image and h is the height of the object
A compound lens is two or more lenses acting together to produce a final image from an object. Microscopes and telescopes are examples of compound lenses. The simplest microscopes and telescopes consist of two convex lenses. The lens that first focuses the object is called the objective. The lens that you actually look through is called the ocular.
32.
For a telescope with a convex lens with a short focal length as its ocular, the objective is a:
A. B. C. D.
concave lens with a focal length that is very long. concave lens with a focal length that is very short. convex lens with a focal length that is very long. convex lens with a focal length that is very short
283
33.
For a convergent mirror with f = 0.30 cm, at what position should an object be placed to generate an image that is three times the object is magnitude of
size?
A. the rays all meet at the same focal point. B. the index of refraction of the glass is the same for
all the colors.
C. the focal length for violet light is smaller than the focal length for red light
A.
D. whether the rays all have the same focal point depends on whether the lens is converging or
diverging.
B.
C.
D.
34.
B.
35.
state to a lower excited or ground state. B. As the wavelength increases, the frequency of the photon decreases. C. It is of higher energy than microwave EM
radiation.
284
be x radians, then which of the following is a possible valuefor the thickness of the glass,if the incident angle
is assumed to be negligibly small?
A. 0.250 m
piece of glass. In order to do so, he bombards the glass with electromagnetic waves, measuring the phase difference between the wave that bounces off of the glass' near surface and the wave that bounces off of the glass' far surface. Knowing that when a wave is traveling from a medium of lower index of refraction to one of a higher index of refraction and is reflected, the wave changes phase by x radians, the scientist tries the following two experimental set ups in order to obtain two data sets:
Set-up I
B.
C. D.
0.375 m
0.500 m 0.625 m
39.
Set-up 1 is constructive, then for the same piece of glass the reflected waves in Set-up 2 would:
A. constructively interfere. B. destructively interfere.
40.
Set-up 2
Air Glass Plastic
Assuming a light ray is passing from glass to plastic as in Set-up 2, which of the following would BEST describe the relationship between the incident angle
(8j), the reflected angle (0R), and the refracted angle (0F)? (All angles are taken with respect to the normal.)
A. 81>8R>0F
B.
8l = 9R> 9F
1^ R^ F
C.
The relationship between phase difference (<j>) and path difference (Ar) used to determine the thickness (t) of the glass is given by the following expression, where (k) is the wavelength:
Equation 1
D.
e, = eR < eF
41.
Ar = -?M>
2k
For Set-up 1 and Set-up 2, respectively, if the light's path-length within the glass is an integer multiple of the reflected light rays' wavelength, then the reflected rays in the two set-ups will be, respectively: A. B. C. D. in phase and out of phase. in phase and in phase. out of phase and out of phase. out of phase and in phase.
For all of his calculations, the scientist used nAh- = LOT, nGlass = 1-50, and npiastic = 1.60, along with radio waves of wavelength one meter. The glass was uniformly thick.
37.
In Set-up 1, a light ray traveling in air and incident on the glass could:
I. pass directly through the glass, entering and exiting the glass at the same angle.
II. achieve total internal reflection on this air-to-glass
interface.
42.
In order to measure the precise thickness of the piece of glass, the scientist must first know its approximate thickness. Why is this the case?
A. These measurements need not be very precise. B. Since waves are periodic, the scientist can obtain a set of possible solutions only from the data. C. The measurement is hurt by the fact that only part
of the wave reflects to its source, while the rest is
transmitted.
285
44.
In moving the object from the position in Trial C to the position in Trial D, what happens to the final image?
C. It becomes larger and stays upright. D. It becomes smaller and stays upright
P
= -
45.
A physicist is curious about the amount of magnification and where the final image will appear, if he puts a diverging lens 10 cm in front of a converging lens and changes the object's distance from the first lens. For a diverging lens with a focal length of -10 cm and a converging lens with a focal length of 10 cm, the results of the physicist's study are given in Table 1. It should be noted that in the representation of the data the diverging lens is referred to as Lens 1, while the converging lens is Lens 2.
Lens 1
C.
D.
Trial C
Trial D
Lens 2
Object
If
B. C.
D.
-0.5 0.5
2.0
10 cm
Figure 1
Trial
A
Pi(cm)
20
10 5
Ql(cm)
-6.67 -5 -3.33
P2(cm)
16.67
15 13.33 5
C
D
40 -10
B. When the object is at one focal point C. When the object is at twice the focal length from
the lens.
-3.33 -20
5
-20 Table 1
30
15
0.5
43. As an object moves towards a converging lens and crosses the focal point, what happens to its image?
A. The image goes from being real and upright to real
and inverted.
48. When an object is placed inside the focal length on the right side of a diverging lens, what type of image is
formed?
B. The image goes from being real and inverted to real and upright C. The image goes from being real and upright to
virtual and inverted.
D. The image goes from being real and inverted to virtual and upright
286
52.
A. an increase in thefocal length of theeye. B. a decrease in the focal length of the eye.
C. the scattering of light by the water.
D. a decrease in the effectiveness of the iris at absorbing light.
A.
B. Look through a polarizer. C. Look through a prism. D. Look through a light-scattering material.
The plastic absorbed light, reducing the amount of reflected light The plastic reflected only one frequency of light. The plastic acted as a semi-polarizer, reflecting and refracting light differently according to the EM
wave's orientation.
D.
1. B
2. 8.
14.
20. 26.
C
A
D
B
3. D 9. A 15. A
21. A
4.
5. A 11. A
17. A
23.
B
6.
12.
7. D
10. A 16. A
22. 28.
D
13. D
19. C
18. A
24. A
25. B
31. D 37. D
43. D
C C A A
B
27. A
29. B
30.
32.
33. B
39. B
34. A
35. D
41. D
36. 42.
C
B
40.
45. D
46. A
52. A
47. B
48. A
49. D
51. C
287
Choice B is the best answer. This question is best solved by first eliminating what we can using common sense and then finding the best answer from the remaining choices using mathematics. We know that flint glass is denser than air, so the light slows down upon entering the flint glass from air. This means that with an incident angle of 60, the refracted angle must be less than 60. This eliminates choice D. We also know the refracted angle cannot be 0 unless the incident ray strikes the boundary in a perpendicular fashion. Because the incident angle is 60, the refracted angle cannot be 0, so choice A is eliminated. We are down to two choices. The passage tells us that light striking the boundary between flint glass and
the surrounding air at an incident angle of 38.1 results in a refracted angle of 90. If vve consider the reverseof this process where light travels from air and strikes a boundary made of flint glass, then the angles should be reversed. So, if the light coming from air strikes the boundary at an angle just slightly less than 90, then the refracted rays would travel a path that is slightly less than 38.1 from the normal axis. This means that an incident angle of 60 should result in a refracted angle less than 38.1, so choice C is eliminated. All that remains is choice B, so it must be the best answer. To solve this question
using math is arduous and not the most time efficient option, but we shall address the process nonetheless. From the information in the passage and Snell's law, we know:
1xsin 60 =(V^ 38.r)'sin ^refracted ' sin 6refractcd =sin 60 xsin 38.1
Because sin 60 is a number less than 1, sin 9refractcd < sin 38.1 .\ refracted < 38.1
Determination of the exact number is challenging without a calculator, but luckily for us, it is a multiple-choice question. This is enough math to support our selection of choice B. The best answer is choice B.
Choice C is the best answer. refraction of the lens material. therefore of identical curvature. material with the greatest index The focal point of a lens depends on the angle of curvature of the lens and the index of In each case, the surrounding medium is air and the lenses are of identical dimensions, and The difference in focal points between the four lenses depends strictly on the materials. The of refraction will bend the light the most and in doing so create a focal point (where the rays
intersect) closer to the lens. This question is looking for the material with the greatest index of refraction. The passage gives us critical angles, which decrease as n-value for the material increases. This means that we are looking for the material with the smallest critical angle. This describes rutile, so choice C is the best answer. Even if we had no idea how to answer the question, the question is asking for an extreme value (closest to the lens). Without any clue, we should at the very least eliminate rock salt and zirconia, because their critical angles are less than the critical angle for polystyrene. The best answer
must be either choice A or choice C. The best answer is choice C.
Choice D is the best answer. The experiment requires that yellow light (k = 589 nm) pass through the two mediums (one of which is air) without being reflected and refracted more than once (only at the boundary), and without being absorbed. If the light undergoes multiple points of refraction, then the ultimate angle cannot be attributed solely to the difference between the material and air. If the material absorbs light then there is a chance that no light will pass, which would result in no intensity at the screen for a reason other than exceeding the critical angle. This means the material must be transparent and uniform, making choices A, B, and C all valid. The light should not be absorbed, so choice D is the best answer. You should note that choices A and D are opposite answers, so it is probable that one of the two is the best choice. The best answer is choice
D.
Choice B is the best answer. Diffraction occurs when light interacts with a slit in a material, which is not the case in this experiment. While monochromatic light may be necessary to study diffraction, it does not impact this experiment in terms of diffraction. Statement I is invalid, which eliminates choices A and C. We know Statement II must be true based on the
remaining choices, but just to verify, different frequencies of light have different indexes of refraction, so if polychromatic light were used, the different wavelengths would exhibit a different degree of bending, resulting in dispersion of the incident light. As such, each color would result in a different critical angle. Statement II is in fact valid. Reflection occurs independent of the frequency of light so whether the light is monochromatic or polychromatic, reflection is still involved.
Statement III is invalid, making choice B the best answer. The best answer is choice B.
288
interface in a perpendicular fashion, it's speed will change, but there will be no change in the orientation of the rays. To
observe refraction, light must strike the boundary at some angle other than perpendicular. This makes choice A the best answer. Choice D should have been eliminated, because the light speeds up when transmitted to the air. Choice B should
Choice A is the best answer. Light initiating from Point a will strike the boundary at a right angle. For light that strikes an
have been eliminated, because the incident angle is 0, which is less than the critical angle for every material in the passage.
Choice C should be eliminated, because light doesn't exhibit such behavior. The best answer is choice A.
Choice Dis the best answer. The index of refraction for water is greater than the index of refraction for air, so light passing
from the disk to water will be bent less than light passing from the disk to air. This means that the angle of refraction is smaller in water than air, eliminating choices A and C. In order to get a refracted angle of 90 in water, a greater incident angle is required than what is required to get a refracted angle of 90 in air. Thus, the critical angle between the disk and air is less than it is between the disk and water. This makes choice D the best answer. The math to support the critical angles
conclusion is as follows.
nmateria!"Sin incident = nair*s'n refracted in air and nmalcrial'Sin incident = nwater*sn refracted in water
So: sin erefractcdinair =nmaterial/^-sin eincident and sin 9refracted in water ="material^^-sin eincident
Because nvvatcr is greater than nair, sin 8refracted in air isgreater than sin 9refractcd in watcr .-. 9rcfracled in air > 0refracted in water
The math supports the selection of choice D. The best answer is choice D.
Mirrors
Choice D is the best answer. First and foremost, the distance from a plane mirror plays no role in the limits of the image
besides intensity. We need consider only the height of the person in front of the mirror, especially the person who is 4 m (nearly thirteen feet) tall, as they are probably from outer space. To understand this better, draw a picture. Let the person be
standing a distance d in front of the mirror. Then the image must appear to be a distance d behind the mirror. In order for
light to reach the person's eyes from the eyes of the image, a light ray must appear to come from the eyes of the image. In actuality, the lightfrom the eyes of the person leaves them, strikes the mirror's surface, and then reflects into their eyes. For light to reach the person's eyes from the feet of their own reflected image, a light ray must appear to come from the feet of the image and enter the person's eyes. In actuality, light from the person's feet strikes the mirror and reflects into their eyes. If
we draw out all the rays, we see that there are two similar triangles:
Plane Mirror
T h;__d_ j_
h " 2d ~ 2
Even a person standing 2 meters tall could see approximately their entire body length in a mirror 1 meter long (remember
that the body extends a bit above the eyes). The best answer is choice D.
Choice A is the best answer. Recall some general observations about plane mirrors: They always form virtual images;
images formed in plane mirrors are of the same size as the original object; images formed in plane mirrors are as far from the mirror as the original object is. The last two observations invalidate statements II and III, leaving choice A as the best answer. To confirm this selection, we need ask only whether spherically convex mirrors always form virtual images (i.e., we need test only the validity of statement I). Yes, spherically convex mirrors can form only virtual images-the fact that you
always see an upright image in any convex mirror is proof of this. Thus, statement I is true. The best answer is choice A.
289
9.
Choice A is the best answer. Let's use the equation given in the passage to solve this one:
1 f
1 +1
s s'
where s = +3f (a plus sign is used, because the object is in front of the mirror). Solving for s' yields: s' = 3f/2. This rules out
choices C and D. If you stick with the convention that positive lengths represent objects and images in front of a mirror, then
you can cross out choice B in favor of choice A. Another way to see that choice A is better than choice B is to realize that when any object beyond a concave mirror's (or even a convex lens') focal point, the image is always real (i.e., it has real light rays meeting in real space). Since real space is in front of a mirror, choice A must be correct. Yet another method for getting choice A would be to trace out the light rays from the object. The best answer is choice A.
10.
Choice A is the best answer. The radius of curvature of the mirror determines where the normal lines to the surface are.
This, in turn, determines where the reflected rays go and means that the radius of curvature affects the focal length. Choice A is correct. The index of refraction applies to refraction, not reflection, so while it affects the focal length of a lens, it is immaterial the focal length of a mirror. The density and compressibility of the reflective material may affect the ease with which the mirror can be shaped, but they do not affect the focal length. The best answer is choice A.
11.
Choice A is the best answer. The law of reflection states that the angle of incidence is equal to the angle of reflection. This law is independent of the frequency (and wavelength) of the incident light and independent of the refractive index of the
material of which the mirror is made. The best answer is choice A.
You may notice that this is the fourth straight question where choice A is the best answer. This was done to work on your psyche and see if such a pattern influences your decision.
12.
Choice C is the best answer. Mirrors work by reflection, so the focal length is determined by the radius of curvature of the mirror and by nothing else. Although the wavelength of the light changes under water, the rays still meet at the same point. This eliminates choice A. A lens on the other hand, works by refraction, which depends on both the radius of curvature of the two sides of the lens and the difference in refractive index between the lens and the surrounding medium. If a lens is immersed in water, then the medium surrounding the lens has a higher index of refraction, which results in less bending of the light rays. By bending less, the rays intersect farther from the lens, meaning that the focal length increases. This makes
choice C the best answer. The best answer is choice C.
Telescopes
Choice D is the best answer. Chromatic aberrations are caused by refraction, so mirrors are in fact free of chromatic aberrations, while lenses are not. Because the reflecting telescopes employ concave mirrors as the objective, while refracting telescopes employ lenses, choice A is an advantage of the reflecting telescope. With a concave mirror, spherical aberrations can easily be corrected. With a lens, the correcting is not done as easily, owing to the curvature of both sides.
This points out another advantage of the reflecting telescope, and it eliminates choice B. In a refracting telescope, the objective must be a convex lens. In a reflecting telescope, the mirror can be parabolic or spherical, making choice C an advantage of the reflecting telescope. Choice C can be eliminated. In a reflecting telescope, the plane mirror sits at the focal point, which is in front of the concave mirror. This means that some incident light is blocked by the plane mirror (the second
mirror), so this is a disadvantage of the reflecting telescope. Choice D is the best answer.
Reflecting
Mirror
Ocular
Cassegrainian Focus
The best answer is choice D.
14.
Choice D is the best answer. It is stated in the passage that reflecting telescopes have large reflecting mirrors. This eliminates choice B. Because a reflecting telescope has a large mirror, it must be considerably larger than a refracting telescope. This eliminates choices A and C and makes choice D the best answer. Most telescopes found in observatories today are reflecting telescopes, which accounts for observatories being so large. Portable telescopes, like the kind you would take on a field trip, are typically refracting telescopes, and they are generally small. The best answer is choice D.
290
15.
Choice A is the best answer. The passage tells us that in a refracting telescope, the rays that pass through the eyepiece must
leave in a parallel fashion. This occurs when the object lies at the focal point. Given that the image of the objective is the object of the eyepiece, we need the first image to form at the focal point of the ocular (eyepiece). This makes choice A the best answer. In Figure 1, vve see that the image created by the objective is at the focal point of the objective. This is remarkable, because the object (be ita star, planet, or galaxy) is ineffect infinitely far from the objective-remember the thinlens equation? The best answer is choice A.
16.
Choice A is the best answer. Looking at Figure 1 in the passage, we see that both focal lengths are shorter than the telescope. The passage defines the telescope length as the distance between the objective and the eyepiece; this distance is
also defined as the sum of the focal lengths of the two lenses. The best answer is choice A.
17.
Choice A is the best answer. Let's recall some basic facts about plane mirrors: For one thing, they reflect light. This rules out choice B, because lightcould possibly reflect onto the secondary mirror. Plane mirrors form a virtual image of the object; this image is equal in size to the object and as far from the mirror as the mirror is from the object. The main disadvantage of these properties, in using the plane mirror to build a telescope, is that the plane mirror does not magnify the image of the object. What looks (to the naked eye) like a speck of starlight reflects onto the secondary mirror as a speck of starlight. The
best answer is choice A.
Questions 18 - 21
18.
Choice A is the best answer. Remembering the UV-IR rule for objects and images: An upright image is always virtual, with respect to the object. This makes Statement I valid. A real object may or may not form a real image. It depends upon the combination of lenses being used. For example, diverging lenses form virtual images from real objects. This makes Statement II invalid. Statements with absolute language, such as "always," should be treated as invalid until you have completed an exhaustive search for contradictory answers. One exception disproves an extreme statement. Finally, light may travel through two lenses before forming the final image. If the second lens is within the focal length of the first lens, then light will travel through the first and second lens before forming the image. This makes Statement III invalid. Because only
Statement I is valid, choice A is the best answer. The best answer is choice A
19.
Choice C is the best answer. This question can be solved systematically, by first noting that vve are dealing with a single, converging lens. Our first approach is to visualize the positions of the object, mirror, and image (in essence to create a minimalistic ray diagram in our mind). For a converging system involving a single mirror or single lens, if the object is between the radius of curvature and focal point, then the image will be an inverted, real image formed beyond the radius of curvature. Given that the focal length is 12 cm, the radius of curvature must be 24 cm, which means that the image must form at a distance greater than 24 cm from the mirror. Only choice C fits describes a point beyond 24 cm. The image is on the left side of the mirror, because reflected rays can only form a real image on the original side of the mirror (where the
object exists).
If you don't like the visualization approach to lens and mirror questions, then you are always welcome to employ math. You need to keep sign conventions in mind, so for a converging mirror, the focal length is a positive value, Had you used a negative value for f, which you would do for a diverging mirror, then you would have errantly come up with a value of -6.67, which is one of the answer choices. Let's take advantage of the shortcut version of the thin lens equation given in the text of
this chapter:
20.
Choice B is the best answer. The sky has color because the Sun's light is scattered by the particles in the atmosphere. In the
absence of any atmosphere, there can be no scattering, so vve would see no color. (Ever see any pictures of the Moon? The
Moon has no atmosphere; the sky as seen from the lunar surface is black.) The best answer is choice B.
21.
Choice A is the best answer. The focal length of a lens is a measure of how much the lens can bend incoming light rays. The index of refraction of oil is higher than that for air, and thus is closer to the index of refraction of the lens. This means that light going from air to glass will be refracted more than light going from oil to glass. The focal length of the lens is therefore greater (farther from the lens) in oil than it is in air. This eliminates choices B and C and makes choice A the best answer. The wavelength of light is shorter in oil than air, so choice D is also eliminated. The best answer is choice A.
291
Choice D is the best answer. To solve for the focal length of the eye, vve use the thin lens formula:
where f is the focal length, s is the object distance, and s' is the image distance. Choosing s' to be 0.02 meters, the length of the eye as mentioned in the passage, and s to be 2 meters, from the question, vve solve for f:
1 f 2 meters
1
0.02 meters
The 1/2 part of the equation above is negligible compared to 1/0.02, so we can essentially ignore it. This leads to the
conclusion that f = 0.02 meters. The best answer is choice D.
23.
Choice B is the best answer. Farsightedness, as defined in the passage, is the inability to focus on nearby objects. Farsightedness occurs because the lens of the eye is not powerful enough to focus on light rays from an object close to the eye. Remember that focusing on objects close up requires a small focal length and therefore, a more powerful lens than focusing on objects that are far away. Looking at the thin lens equation, one way this could happen would be if the eye was too short (if s' was too small), but that is not an option. The cornea needs to have a rounded shape to bend light rays from an object close to the eye. This means that an inability to focus on nearby objects is because the curvature of the lens is not great enough, which can be attributed to either the cornea not being round enough, or the ciliary muscles inability to contract the lens. Statements II and III go together, so choice B is the best answer. The best answer is choice B. Choice A is the best answer. When the ciliary muscles of the eye contract, the eye becomes more round. The effect of this is to cause incoming light rays to get bent more as they enter the eye, which means that the focal length had to decrease, so Statements I and III are valid. You should notice that Statements I and III are complementary and that Statements II and IV are complementary. This eliminates choices C and D. The ciliary muscles of the eye contract when vve are focusing on objects closer to the eye. Remember-the smaller the focal length, the more powerful the lens and the more it is able to bend
24.
light rays. Lens power, P, is defined as Vf- A small focal length is required to focus on objects close to the eye. If you are
not sure about this last part, try plugging some numbers into the thin lens equation:
1 =1 + 1
f s s-
Upon focusing on an object 2 meters away means that the eye has a focal length of 0.02 meters, or a power of 50 diopters. If
vve use 0.25 meters for the object distance:
1=
f
!
0.25 meters
1
0.02 meters
and solve for f, vve get f = 0.019 meters, or a power of 54 diopters. The best answer is choice A.
25.
Choice B is the best answer. A nearsighted person can see objects thatare near, but cannotsee objects thatare far away. To
correct for such a condition, the ideal lens should take a far away object and create an image that is near. With a concave (divergent) lens, the image in an upright, virtual image that is located inside of the focal length. This means that a far away object will generate a nearby image, which means that the divergent lens has taken an object outside the field of vision and generated an image within the field of vision. A nearsighted person benefits from a concave lens. You may also note that a
nearsighted person has a retina that is abnormally longer, so the image focuses before the retina. A divergent lens will spread
the rays before they enter the eye, so that the image can now focus at the retina. The best answer is B.
26.
Choice C is the best answer. The passage tells us that the cornea has the highest index of refraction of all of the transparent parts of the eye, making choice C the best answer. A substance with a high index of refraction bends light rays more than a substance with a small index of refraction. So whatjob does the lens do? The passage tells us that the cornea is inflexible-it
cannot bend and change its radius of curvature. However, the lens is able to bend and change its radius of curvature, thereby changing the focal length of the cornea-lens system. The lens makes it possible to focus on objects at variable distances from
the eye. The best answer is C.
27.
Choice A is the best answer. Blue light has a smaller wavelength than yellow light. Therefore, it sees a higher index of
refraction than does yellow light. This means that the blue light will be bent more than the yellow light upon passing through the eye, and therefore the blue light will focus in front of the retina. This eliminates choices B and C and makes choice A the best answer. Light will not be focused on the cornea, so choice D is eliminated. The best answer is A.
292
Different Lenses
Choice C is the best answer. A diverging lens does not have a point where all the light rays actually meet. In order to measure the focal length of a diverging lens, a converging lens must be used. The two lenses will form a compound lens-the image of the first lens acts as an object for the second lens. By knowing the location of the final real image, and by knowing the focal length of the converging lens, vve can work backwards to determine the focal length of the diverging lens. This makes choice C the best option of the choices. Choice A is incorrect, because parallel light rays do not meet any place when they travel through a diverging lens. Choice B is incorrect, because a real image is needed, so that vve may actually measure an image distance. Diverging lenses only produce virtual images. Choice D is incorrect. Although the light rays are indeed diverged away from the lens, vve can still speakof how much these light rays are refracted, and this is all vve mean by focal
length. The best answer is C.
29.
Choice B is the best answer. The purpose of a microscope is to enlarge objects. By placing the object just outside the focal length of the objective, vve insure a large image distance. This in turn provides a large magnification, according to:
M = -i
o
ChoiceA is incorrect. By placing the object just inside the focal length of the objective, we create a virtual image. Choice C is incorrect. By placing the object far away from the focal point, vve insure a small image distance, which means a small magnification. Choice D is incorrect, for the same reason that choice A is incorrect. This will put the object inside the focal
length again, which means the production of a virtual image. The best answer is choice B.
30.
Choice B is the best answer. This question focuses on recall. Light traveling through a medium will exhibit the same wave speed regardless of the frequency, so choice A is eliminated. Because vve see that white light is dispersed (refracted), choice D can be eliminated. The light with the highest frequency (violet light) is "bent" to the greatest extent, which means that light with the greatest frequency is most refracted. Choice C is eliminated. The best answer is choice B. Choice D is the best answer. A virtual image may indeed serve as a real object. This is the principle behind glasses and contacts. This makes Statement I invalid, which eliminates choices A and C. A real object may or may not form a real image. It depends upon the combination of lenses being used. For example, diverging lenses form virtual images from real objects. This makes Statement II invalid, which eliminates choice B and leaves only choice D. Finally, light may travel through two lenses before forming the final image. If the second lens is inside the focal length of the first lens, then light will travel through the first and second lens before forming the image. This confirms that Statement III is invalid. When solving the problem quantitatively, vve assume the formation of something called a "virtual object." This is the principle behind the telephoto lens. The best answer is choice D.
Choice C is the best answer. Because the ocular for this particular telescope is a convex lens, the objective needs to be a convex lens. This will doubly invert the image, resulting in a final image that is upright. This eliminates choices A and B. The focal length of the ocular is dictated in part by the physical size of the telescope and in part by what vve want the telescope to do. A telescope focuses on objects that are very far away and tries to magnify them. In order to enlarge them, vve need an objective with a long focal length, to make s1 as large as possible. The best answer is choice C.
31.
32.
Questions 33 - 36
33.
Choice B is the best answer. For a convergent mirror to generate a real image, the object must be beyond the focal point, so choice A can be eliminated immediately. With f = 0.3 cm, R must be 0.6 cm. If the object is placed at the radius of curvature, then the image will also form at R, resulting in an image with the same magnitude of size as the object. Choice D is eliminated. Only math can make the final distinction between choices B and C. If the object is at 0.4 cm, then the image will form at (0.4 x 0.3)/(0.4 - 0.3) = 0.12/0.10 = 1.2 cm. Magnification is found using m = -(dj/d0) = -(1.2/0.4) = -3. Because m is -3, the image is three times as large as the object and it is inverted. The best answer is choice B. Choice A is the best answer. Snell's Law tells us that light will change direction upon entering a new medium, as long as the incident ray is not perpendicular to the boundary. Light bends toward the normal if the light enters a denser medium from a less dense medium, and light bends away from the normal if light enters a less dense medium from a denser medium. Picture I is consistent with light entering a denser material from a less dense material; Picture V is consistent with light entering a less dense material from a denser material. Picture II can be eliminated; the light does not show a direction change upon entering the new medium. Although the light in Pictures III and IV do show a direction change upon entering the new material, it ends up traveling along the normal. This could only happen if the incident angle was 0. Only Pictures I and V
are valid. The best answer is choice A.
34.
293
35.
Choice D is the best answer. We are told here that ultraviolet radiation and visible light are associated with transitions between different electronic energy levels, so it is true that visible light can be emitted when an electron falls from an excited state to a ground state. This eliminates choice A. For all electromagnetic radiation, including visible light, the wavelength of a photon increases as its frequency decreases. This obeys the equation v = f-k (where v is the speed of the photon, / is the
frequency of the photon, and k is the wavelength of the photon), so choice B is eliminated. Visible light has more energy
than microwave radiation. Even if you were unaware of this, the passage states that electronic transitions are due to visible
photons, while vibrational transitions can be caused by microwaves. Because electronic transitions are of a higher energy
than vibrational transitions, it can be concluded that visible light is of a higher energy than microwaves. This makes choice C valid, which eliminates it from being "NOT true." Visible light ranges from about 400 nm to about 700 nm, so choice D is
not true-so it is the best answer. The best answer is choice D.
36.
Choice C is the best answer. The index of refraction for a material is somewhat wavelength dependent. When two colors of
light travel through the same lens, they are subsequently refracted different amounts, and thus will not meet at the same focal
point. Choices A and B are incorrect for the reasons just mentioned. Whether the lens is converging or diverging, different
colors are still refracted different amounts, so for converging or diverging lenses, different colors will have different focal
points. This eliminates choice D. Because violet light is refracted more than red light, it has a shorter focal length. The best
answer is choice C.
Thin Films
Choice D is the best answer. If vve think about the path a light ray takes in Setup 1, vve see it will first bend toward the normal to the surface when entering the glass, because it is moving from a region of a lower index to one of a higher index. Upon exiting the glass, the light ray will refract away from the normal, because it is moving from a region of higher index of refraction to one of a lower index. The net result is the light ray entering and leaving the glass at the same angle, so vve can
see that Statement I is correct. Since total internal reflection can occur only when the light is moving from a region with a
higher index (nGLAss = 1-50) to one of a lower index (nAjR = 1.01), Statement II is incorrect, while Statement III is correct.
The answer that corresponds to choosing both Statements I and III is answer choice D. The best answer is choice D.
38.
Choice A is the best answer. If the light ray is coming in approximately perpendicular to the surface of the glass, then Ar =
2t, where t represents the thickness of the glass, because the light ray that reflected off of the second surface must travel into
the glass and back out. Thequestion states that the waves are re out of phase, so this problem becomes a simple calculation:
Ar = 2t = A^j)
2re
and
Thus, vve can see that the best answer is choice A, or the pieceof glass is 0.25 m thick. The best answer is choice A.
39.
Choice B is the bestanswer. If in Setup 1 the interference isconstructive, then vve know that the phase difference between reflected waves is some multiple of 2rc. Since in Setup 1 vve have a phase change in going from air to glass (but not from glass to air), while in Setup 2 there is a phase change in going from air to glass (as well as going from glass to plastic), Setup
1 and Setup 2 aren out of phase with each other. This means that in Setup 2, the phase difference between reflected waves is
some odd multiple of jc. Odd multiples of x correspond to destructive interference. The best answer is choice B.
40.
Choice B is the best answer. The incident and reflected beams are always equal, so vve can eliminate choices A and C. Also, when light is moving from a region with a lower index of refraction (nGLAss = 1-50) to a region with a higher index of refraction (nPLASTic = 1-60), the light ray bends towards the normal to the surface. Angles of refraction are measured with
respect to the normal, so the initial angle is greater than thefinal angle, or 6j = Or > 0p. The best answer is choice B.
41.
Choice D is the best answer. In order to answer this question, vve must look at the phase change of the wave at each
boundary. It is stated in the passage that when light goes from a region with a lower index of refraction to a region with a higher index of refraction, the reflected wave changes phase by re. In this case, there is a phase change of x in the reflected wave when light passes from air to glass, as well as from glass to plastic. Applying this to Setup 1, only the first reflected wave gathers a phase change of re, while the wave returning from the second surface obtains no phase change upon reflection. If the thickness of the glass is some multiple of the wavelength, then the two reflected waves for Setup 1 will arrive outof phase by re, so they interfere destructively. Similarly, in Setup 2, the first reflected wave gathers a phase change ofre, as well as the wave returning from the second surface. This happens because the wave is traveling from a region with a lower index to one with a higher index in both cases. Assuming again that the thickness of the glass is some multiple of the wavelength, the two reflected waves for Setup 2 both arrive jt out of phase from the incident wave, or in phase with each other. This combination corresponds to constructive interference. Destructive interference for Setup 1, and constructive
interference for Setup 2 corresponds to out of phase for 1 and in phasefor 2. The best answer is choice D.
294
42.
Choice B is the best answer. Unless the answer is obvious, vve should solve this one by the process of elimination. Choice A is incorrect, because the whole reason the scientist was doing this experiment in the first place was to obtain a precise measurement. In disproving choice C, as long as some of the wave is reflected, it is the only part of the wave vve are
interested in for our measurements. Furthermore, choice D is not good, because the results of any experiment should be questioned, if they do not agree with another experiment meant to measure the same thing. This leaves us with the only
choice that makes sense, choice B. In taking data, it is possible to measure a phase difference only between 0 and 2re, because
the waves are periodic. In trying to apply the data to the equation, Ar =^/g^, an experimental phase difference of, say, re
could correspond to an actual phase difference of re, 3re, 5re, etc.... Therefore, it would be useful to have an approximate value of the thickness first, in order to know which "actual phase" the experimental phase corresponds to. The best answer is
choice B.
Double Lens
Choice D is the best answer. We can find out what happens to an object's image as vve cross the focal point by looking at the lens equation, where p represents the position of the object and q represents the position of the image:
1 = 1 +1
If the object is outside the focal point, then p > f, so:
1>1
f P
This is to say that the denominator on the left being a smaller number makes the overall fraction larger. When this is true, q must be positive in order to satisfy the lens equation. Thus, when vve are outside the focal point of a converging lens, the
image is real. Looking at the magnification equation:
m-fl
P
we also notice that since q and p are both positive, the image is inverted. Only choices B and D satisfy this condition for when the object is outside the focal point. When we move the object inside the focal point of a converging lens, then f > p,
so:
1>1
P f
When this is true, q must be negative in order to satisfy the lens equation. Thus, when vve are inside the focal point of a converging lens, the image is virtual. Also, since q is negative and p is positive, upon looking at the magnification equation vve see that the image must then be upright. In conclusion, when moving an object from outside the focal point of a converging lens to inside the focal point, the image goes from being real and inverted to virtual and upright. This is one of those random facts that will make future questions dealing with a single mirror or a single lens easier to solve. The best
answer is choice D.
44.
Choice A is the best answer. Looking at the data in Table 1, one notices by comparing Trials C and D that the magnification goes from -2.0 to 3.0. Since the magnitude of the magnification in Trial D is larger than in Trial C, the final image gets bigger. Also, the image goes from being inverted in Trial C to being upright in Trial D. The best answer is choice A. Choice D is the best answer. To find out where the final image is formed, look at the data for q2- If the final image is formed on Lens 1, q2 should be 10 cm to the left of Lens 2, or -10 cm. Table 1 shows that this corresponds to choice D. The
best answer is choice D.
45.
46.
Choice A is the best answer. If vve want to find the magnification of Lens 2, vve must use both p2 and q2 and the magnification formula, as follows:
We calculate a value of -2 for the magnification of Lens 2 in Trial B. The best answer is choice A.
47.
Choice B is the best answer. For any lens, the image is formed at infinity when Vn = 0. Since the focal length of a
converging lens is positive, then Vn = 0 when p = f. Thus, the image of a converging lens is formed at infinity when the object is at the focal length of the lens. The best answer is choice B.
295
48.
Choice A is the best answer. We must look at the lens equation to figure outthis question. Since the object is to the right of the lens and the lens is diverging, both p and q are negative. If the object is placed inside the focal length, the magnitude off
is greater than the magnitude of p, so the magnitude of Vp is greater than the magnitude of Vf. Since Vp is a larger negative
number, then in order to satisfy the lens equation, q must be positive. If q is positive, the magnification equation indicates that the image isupright. This rules outchoices Band D. The image will be virtual; this can be shown by a bit of ray tracing (see the diagram below). Since actual light rays do not come from the point inspace occupied by the image, the image is said
to be virtual. This makes choice A correct. As a general reminder, diverging lenses always form virtual images.
Lens 1
Questions 49 - 52
49.
Choice D is the best answer. When an object is placed just inside the focal length of a concave (converging) mirror, the
resulting image will be virtual, upright, and enlarged. You can verify this using the lens equation:
1 = 1 +1
Ifs is less than f, then s' must be a negative number for the equation to work out. Anegative value for the image implies that it is a virtual image. This eliminates choices A and B. For a single mirror or single lens, a virtual image is always upright.
This confirms that choice D is the best answer. The best answer is choice D.
50.
Choice B is the best answer. Refracted light can be polarized, at least partially so. By looking through a polarizer and rotating it, vve can see whether the intensity ofthe light changes. Ifthe intensity does not change, then the light was coming straight from the real object. Ifthe intensity does change, then the light was refracted-the apparent object was a mirage. The
best answer is choice B.
51.
Choice C is the best answer. As a good polarizer should do, the one in the question filters 50% ofambient light as long as
the light is a random assortment of EM waves. Light reflected off of the plastic doesn't show the same behavior as the
random light, being that the amount of light reflected off the plastic and passing through the polarizer varies with the orientation of the polarizer. Because the orientation ofthe polarizer impacts the amount of light that passes, the best answer must be involve some form of polarization. While the plastic may absorb light, that would explain a reduction in intensity,
but not a dependence on the orientation of the polarizer. Choice A is eliminated. If the plastic were to reflect only one frequency oflight, then the reflected light would have a distinct color, but that wouldn't explain the polarization. Choice Bis eliminated. The plastic does not emit light, because it is not an energy source. This eliminates choice D. The best explanation is that light reflects off the plastic differently, depending on the orientation of its electric wave relative to the plastic surface. This means that the reflected light off of the plastic (the glare) is semi-polarized. This means that the polarizing filter's impact will depend on its orientation relative to the plastic surface. When the polarizer is perpendicular to the plastic surface,
it will do its greatest filtering. The best answer is choice C.
52.
Choice A is the best answer. Water has a higher index ofrefraction than air, the medium that the eye normally receives light from. Light rays are bent and focused as they pass through the eye because the rays go from air to a medium with a higher
index of refraction. Under water, the medium and the components of the eye now have similar indexes of refraction. This
means that the light rays do not bend as much when they pass from water into the eye. Less bending means a less powerful
lens, which means an increase in the focal length of the eye. This eliminates choice B. The best answer is choice A.
296
Page
124 75
Topic
Electromagnetic Spectrum Electromotive Force (emf) Electrophoresis
Electrostatics
Page
233-234
176-177
143
199
131,173
60
115 123
176
39
73-74, 98
96 14 79
137,142,157
243 121
Floating Object
Fluid
62
55
Bulk Modulus
81,94
60
184 184
193 192
246
19
16,41
84 246 238
213 173 234
Capacitors in Parallel Capacitors in Series Capacitor Charging Cathode-ray Tube Closed Pipe
Combination of Lenses
185-186 154
Insulator
20-21,41
257-258 247-250 251 177
188-190 188-190
76 251 258
173
71,98
251-252
247 116 242 160 9 55
Lens Aberrations
Lenz's Law
136
7 131 252
Density
Dielectric Constant
Diffraction
126,184 265,271
263 244 12-15 79
Longitudinal Wave Magnetic Field Magnification of Image Mass Spectrometer Microscope Millikan Oil Drop Experiment
Mirror
139,140,159 258,283
152
247,279
78
7
Modulus of Elasticity
Molecular Inertia
4,26, 36
120
282
246
179-180
18-19,41
236
217
Electrical Resistance
Electromagnetic Radiation
233-234
Pascal's Principle Pitch (Sound Frequency) Plane Polarized Light Plastically Deformed
57-58 9
235 78
Topic
Poiseuille's Principle
Prism
Radius of Curvature Rarefaction
Page
66,69,101
269
247 6
Topic
Standing Wave
Strain
Stress
Page
17
Sunken Object
Surface Tension
Real Image
Red Shift Reflection
246
14 238
64
Telescope
Thin Film Interference
280,283
261
Refraction
238
246
57 177
191 192 191
Tuning Fork
Turbulence Turbulent How
76
76 78 35
Sonar
Snell's Law
26, 30,36
240
55,57,63 6
Velocity Selector Virtual Image Viscosity Viscous Retarding Force Visible Spectrum Wheatstone Bridge Young's Double Slit Experiment Young's Modulus (of Elasticity)
139,140,156
246
66
67
233-234 216
259
79,86
Topic
Limiting Cases Multiple Concepts Quantitative Change Sunken Object Calculation Trick Thin Lens Shortcut Equation Unit Analysis
Page
180, 181
62-63,112 68
1\ -
/CO
/co
Date Reviewed:
/- -
/ cO
/ co
* c
/ CO
Ife
ERKELEY
R-E'V'I'E-W
H 1.0 3 Li 6.9 11 Na
4
He 4.0 5 B 10.8
7 N 14.0 15 P 31.0
8 o
9 F 19.0
17
10
Be 9.0 12
C
12.0
14
Ne
20.2 18
Ar
16.0
16
13
AI
Mr
24.3 20
21
Si
28.1 32
s
32.1 34
CI
35.5
23.0
19 K 39.1
27.0
22 Ti 23 24 Cr 25 Mn 54.9 43 26 Fe 55.8 44 Ru 101.1 27 28 Ni 58.7 46 29 30 Zn 31
33 As 74.9
51
35
Br
Ca
40.1
Sc
45.0
V 50.9
41
Co
58.9
45 Rh 102.9 77 Ir 192.2 109
Cu
Ga
69.7
49 In 114.8
Ge
Se 79.0
52 Te
47.9
40 Zr
52.0
42
63.5
47
65.4
48
72.6
50
79.9
53 I 126.9 85 At
37
Rb 85.5 55 Cs 132.9 87 Fr
38 Sr
87.6 56
39 Y
88.9
Nb
Mo 95.9
74 W 183.9 106
Tc
Pd
106.4 78 Pt
Ag
107.9
79 Au
Cd
112.4 80
Sn
118.7 82 Pb
Sb
121.8
91.2
72 Hf 178.5 104
92.9
73
(98)
75
127.6
84 Po
Ba
137.3 88
571 LaT
138.9
76 Os
190.2 108 Hs
81
Ti 204.4 113 Uut
83 Bi
Ta 180.9
105
Re 186.2
107
Hg
112
Rn
195.1
110 Ds
(209)
116
(210)
117
(222)
118 Uno
89 R
Ra
Ac
(227)
Rf
Db
Sg
Bh
Mt
Rg
(272)
Cn
Uuq
(289)
Uup
(291)
Uuh
Uus
(223) (226)
(261)
(262)
(266) (264)
(277) (268)
(271)
(277)
(287)
(292)
(292)
(293)
58
59
Pr
I 60
Nd
61
Pm
1 62
Sm
63 Eu
64
65 1 66
67 Ho
68
Er 167.3 100 Fm
69 Tm
70
Yb
173.0 102 No
1 71
Lu
175.0 103 Lr
Ce
140.1
140.9 1144.2
91
Gd
157.3 96
(145) 150.4
93 94
152.0 95
Am
158.9 | 162.5
97 98
Tb
Dy
164.9
99 Es
168.9
101
90
92 U
Th
Pa
Np
Pu
Cm
Bk
Cf
Md
232.0
(243) (247)
(247) (251)
(252) (257)
(258) (259)
(260)
Physics