Escolar Documentos
Profissional Documentos
Cultura Documentos
LC-37D44U
SERVICE MANUAL
No. S18D7LC37D44U
MODEL LC-37D44U
In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 9. PRINTED WIRING BOARD ASSEMBLIES
IMPORTANT SERVICE SAFETY [1] R/C, LED Unit.........................................................9-1
PRECAUTION............................................................ i [2] KEY Unit.................................................................9-2
PRECAUTIONS A PRENDRE LORS DE LA [3] MAIN Unit...............................................................9-3
REPARATION ........................................................... ii
PRECAUTIONS FOR USING LEAD-FREE CHAPTER 10. SCHEMATIC DIAGRAM
SOLDER ...................................................................iii [1] DESCRIPTION OF SCHEMATIC DIAGRAM .......10-1
PRECAUTIONS IN SERVICING THE HDCP- [2] R/C, LED Unit.......................................................10-2
KEY ROM................................................................. iv [3] KEY Unit...............................................................10-3
[4] MAIN Unit.............................................................10-4
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS .................................................1-1 Parts Guide
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS ........................................................3-1
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ...............................5-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. • Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing. and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
C A U T I O N : F O R C O N T I N U E D PROTECTION
reversed. (If necessary, a nonpolarized adaptor plug must be used
AGAINST A RISK OF FIRE REPLACE ONLY WITH only for the purpose of completing these checks.)
SAME TYPE FUSE.
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
F7101 (250V 6.3A)
must be corrected before returning the monitor to the owner.
F7102 (250V 1A)
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard) 1.5k ohm
Before returning the receiver to the user, perform the following 10W
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
0.15 µF
4. Inspect all protective devices such as non-metallic control knobs, TEST PROBE
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current
in the following manner. TO EXPOSED CONNECT TO
• Plug the AC cord directly into a 120 volt AC outlet. METAL PARTS KNOWN EARTH
GROUND
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-37D44U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
LC-37D44U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
iii
LC-37D44U
PRECAUTIONS IN SERVICING THE HDCP-KEY ROM
The HDCP-KEY ROM shall be protected and managed for its information inside. In servicing this ROM, therefore, take the following information pro-
tection/management measures.
1) When disposing of the component parts and PWBs, destruct the IC itself in a proper way.
(For repairing or replacing the component parts and PWBs as well as clearing those in stock)
2) In storing the component parts, protect and manage them against theft and disclosure.
(For storing the service parts, service units, etc.)
iv
LC-37D44U
CHAPTER 1. SPECIFICATIONS
LC-37D44U
Service Manual
[1] SPECIFICATIONS
1–1
LC-37D44U
CHAPTER 2. OPERATION MANUAL
LC-37D44U
Service Manual
Part Names
TV (Front)
OPC indicator
SLEEP indicator
POWER indicator
TV (Top/Rear)
AC INPUT terminal
INPUT 1 terminals
SERVICE terminal
INPUT 2 terminals
Antenna/Cable in
INPUT 3 terminals
2–1
LC-37D44U
Part Names
2–2
LC-37D44U
QUICK REFERENCE
Attaching/Detaching the Stand Setting the TV on the Wall
Before attaching (or detaching) the stand, unplug the AC CAUTION
cord from the AC INPUT terminal.
This TV should be mounted on the wall only with the
Before performing work spread cushioning over the base
AN-37AG5 (SHARP) wall mount bracket. The use of
area to lay the TV on. This will prevent it from being
other wall mount brackets may result in an unstable
damaged.
installation and may cause serious injuries.
CAUTION Installing the TV requires special skill that should
Attach the stand in the correct direction. only be performed by qualified service personnel.
Do not remove the stand from the TV unless using an Customers should not attempt to do the work
optional wall mount bracket to mount it. themselves. SHARP bears no responsibility for
Be sure to follow the instructions. Incorrect installation improper mounting or mounting that results in
of the stand may result in the TV falling over. accident or injury.
Using an optional bracket to mount the TV
1 Confirm that there are 9 screws and a hex key
supplied with the stand unit. You can ask a qualified service professional about
using an optional AN-37AG5 bracket to mount the TV
to the wall.
Carefully read the instructions that come with the
2 Attach the supporting post for the stand unit onto bracket before beginning work.
the base using the box for the stand unit as shown
below.
Hex key 3 Hanging on the wall
AN-37AG5 wall mount bracket.
Screws (See the bracket instructions for details.)
0/5/10/15/20°
2–3
LC-37D44U
Appendix
Troubleshooting
Problem Possible Solution
• Unit cannot be operated. • External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning off the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not • Are batteries inserted with polarity ( , ) aligned?
operate. • Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated near the remote control sensor?
• The TV sometimes makes a • This is not a malfunction. This happens when the cabinet slightly expands and
cracking sound. contracts according to change in temperature. This does not affect the TV's
performance.
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
The example of an error message
Error code Possible Solution
displayed on a screen
• Failed to receive broadcast. E202 • Check the antenna cable. Check that the antenna is correctly
setup.
• No broadcast now. E203 • Check the broadcast time in the program guide.
2–4
LC-37D44U
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal.
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz *
31.5 kHz 60 Hz O
VGA
640 x 480 37.9 kHz 72 Hz O
37.5 kHz 75 Hz O
35.1 kHz 56 Hz O *
37.9 kHz 60 Hz O
PC SVGA 800 x 600
48.1 kHz 72 Hz O
46.9 kHz 75 Hz O *
48.4 kHz 60 Hz O
XGA 1024 x 768 56.5 kHz 70 Hz O
60.0 kHz 75 Hz O
WXGA 1360 x 768 47.7 kHz 60 Hz O
*These 3 formats are not supported by the analog RGB terminal.
2–5
LC-37D44U
CHAPTER 3. DIMENSIONS
LC-37D44U
Service Manual
[1] DIMENSIONS
32 15/ 32 (824.4)
23 1/ 32 (585)
25 3/ 32 (637)
18 17/ 64
(463.8)
14 29/ 64 (367)
2 1/ 16
(52)
15 27/ 32 (402)
2 25/ 32 3 3/ 4
7 7/ 8 (200) (70.3) (95)
3 61/ 64
(100)
(200)
7 7/ 8
9 1/ 16 (230)
3–1
LC-37D44U
CHAPTER 4. REMOVING OF MAJOR PARTS
LC-37D44U
Service Manual
Rear Cabinet
Front Cabinet
Stand
4–1
LC-37D44U
3. Remove the 8 lock screws, 2 lock screws, 2 lock shafts and detach the Main Shield.
4. Disconnect all the connectors from all the PWBs.
5. Remove the KEY Unit Ass'y.
3
3 3
Main Shield
Operation Button 5
KEY Unit
FPC LB
4 KM
PD
LB 4
KM 4
PD
RA SP
4 4
SP-R SP-L
4–2
LC-37D44U
6. Disconnect all the connectors from all the terminals of Speaker (L) (R) and detach the Speaker (L) (R).
7. Remove the 2 lock screws, 4 lock screws and detach the MAIN Unit.
8. Remove the 2 lock rivets and detach the Heat Sink.
9. Remove the 2 lock screws and detach the INVERTER Unit.
10.Remove the 2 lock screws and detach the POWER Unit.
7 7 10
POWER Unit
MAIN Unit
8
Heat Sink
7
6 6
Speaker (R) Speaker (L)
9
INVERTER Unit
4–3
LC-37D44U
11.Remove the 1 lock screw and detach the Bottom Cover.
12.Remove the 4 lock screws and detach the Stand Fix Angle.
13.Remove the R/C, LED Unit.
Bottom Cover
11
4–4
LC-37D44U
14.Remove the 4 lock screws and detach the LCD Panel Module.
15.Remove the 2 lock screws and detach the LCD Fix Angle-B.
16.Remove the 2 lock screws and detach the LCD Fix Angle-T.
17.Remove the 9 lock screws and detach the VESA Angle.
17 17
VESA Angle
VESA Angle
14
14
LCD Fix Angle-B
16
15
LCD Fix Angle-T
4–5
LC-37D44U
CHAPTER 5. ADJUSTMENT
LC-37D44U
Service Manual
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit: DUNTKE450FM01
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file D44UAxxx.USB (named temporarily) for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
5–1
LC-37D44U
5. Even a single failure in the process will trigger the upgrade failure screen.
UPGRADE FAILURE
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
UPGRADE SUCCESS
7. Unplug the AC cord and remove the USB Memory for version upgrade.
8. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
LC-37D44U
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file D44UVAxxx.USB and D44UMxxx.BIN (named temporarily) for monitor microprocessor software version upgrade to the USB memory.
6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
UPGRADE FAILURE
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
7. Up on completion of the whole process, power and OPC LED will blink alternately. Also, the upgrade success screen will be shown if upgrade
screen was shown at 5.
UPGRADE SUCCESS
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
5–3
LC-37D44U
2.4. Upgrading Panel timing controller software
Create the USB memory for Panel timing controller software version upgrade in the same manner as explained in the “Main software version
upgrade.”
Copy the file D44UAxxx.USB and D44UAxxx.TCN to USB memory.
UPGRADE SUCCESS
6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
UPGRADE SUCCESS
7. Unplug the AC cord and remove the USB Memory for version upgrade.
8. Now the software version upgrade is complete.
5–4
LC-37D44U
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL (–)” and “CH ( )” keys at a time.
(The “VOL (–)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
5–5
LC-37D44U
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
5–6
LC-37D44U
Page Line Item Description Remarks (adjustment detail, etc.)
6 [HDTV]
1 COMP33K ADJ (INPUT1) Component 33K picture level adjustment (main)
2 COMP33K ADJ (INPUT3)
3 COMP33K Y A_GAIN
4 COMP33K Cb A_GAIN
5 COMP33K Cr A_GAIN
6 COMP33K Y D_GAIN
7 COMP33K Cb D_GAIN
8 COMP33K Cr D_GAIN
9 COMP33K Y OFFSET Y OFFSET adjustment value
10 COMP33K Cb OFFSET Cb OFFSET adjustment value
11 COMP33K Cr OFFSET Cr OFFSET adjustment value
7 [ANALOG RGB]
1 ANALOG RGB ADJ Analog RGB picture level adjustment
2 R A-GAIN
3 G A-GAIN
4 B A-GAIN
5 R D-GAIN
6 G D-GAIN
7 B D-GAIN
8 R OFFSET
9 G OFFSET
10 B OFFSET
8 [M GAMMA IN]
1 LEV1 Standard value 1 Adjustment gradation setting.
2 LEV2 Standard value 2
3 LEV3 Standard value 3
4 LEV4 Standard value 4
5 LEV5 Standard value 5
6 LEV6 Standard value 6
9 [M GAMMA R1]
1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment
2 MG1G WB adjustment Point 1, G adjustment value
3 MG1B WB adjustment Point 1, B adjustment value
4 MG2R WB adjustment Point 2, R adjustment value
5 MG2G WB adjustment Point 2, G adjustment value
6 MG2B WB adjustment Point 2, B adjustment value
7 MG3R WB adjustment Point 3, R adjustment value
8 MG3G WB adjustment Point 3, G adjustment value
9 MG3B WB adjustment Point 3, B adjustment value
10 [M GAMMA R4]
1 MG4R WB adjustment Point 4, R adjustment value Parameter for six-point adjustment
2 MG4G WB adjustment Point 4, G adjustment value
3 MG4B WB adjustment Point 4, B adjustment value
4 MG5R WB adjustment Point 5, R adjustment value
5 MG5G WB adjustment Point 5, G adjustment value
6 MG5B WB adjustment Point 5, B adjustment value
7 MG6R WB adjustment Point 6, R adjustment value
8 MG6G WB adjustment Point 6, G adjustment value
9 MG6B WB adjustment Point 6, B adjustment value
11 [SOUND 1]
1 Audio Switch
2 Flat Mode
3 ADC Volume 1
4 ADC Volume 2
5 ADC Volume 3
6 ADC Volume 4
7 ADC Volume 5
8 ADC Volume 6
5–7
LC-37D44U
Page Line Item Description Remarks (adjustment detail, etc.)
12 [SOUND 2]
1 Lip Sync LR
2 Lip Sync Monitor
3 Lip Sync SW
4 LR Func Vol AIN (2ch)
5 LR Func Vol HDMI (2ch)
6 LR Func Vol ATV (2ch)
7 LR Func Vol DTV (2ch)
8 Input Trim (2ch)
13 [SOUND 3]
1 PEQ1 F0
2 PEQ1 Q
3 PEQ1 Gain
4 PEQ1 Gain Limit
5 PEQ1 Fade Time
6 PEQ2 F0
7 PEQ2 Q
8 PEQ2 Gain
9 PEQ2 Gain Limit
10 PEQ2 Fade Time
14 [SOUND 4]
1 PEQ3 F0
2 PEQ3 Q
3 PEQ3 Gain
4 PEQ3 Gain Limit
5 PEQ3 Fade Time
6 PEQ4 F0
7 PEQ4 Q
8 PEQ4 Gain
9 PEQ4 Gain Limit
10 PEQ4 Fade Time
15 [SOUND 5]
1 PEQ5 F0
2 PEQ5 Q
3 PEQ5 Gain
4 PEQ5 Gain Limit
5 PEQ5 Fade Time
6 PEQ6 F0
7 PEQ6 Q
8 PEQ6 Gain
9 PEQ6 Gain Limit
10 PEQ6 Fade Time
16 [SOUND 6]
1 PEQ7 F0
2 PEQ7 Q
3 PEQ7 Gain
4 PEQ7 Gain Limit
5 PEQ7 Fade Time
6 Subsonic Filter
17 [SOUND 7]
1 Output Trim
2 Clipper
3 Sub Volume Default
4 Sub Volume SH Bass
5 Mon Func Vol AIN
6 Mon Func Vol HDMI
7 Mon Func Vol ATV
8 Mon Func Vol DTV
9 SW Func Vol AIN
10 SW Func Vol HDMI
11 SW Func Vol ATV
12 SW Func Vol DTV
5–8
LC-37D44U
Page Line Item Description Remarks (adjustment detail, etc.)
18 [SOUND 8]
1 BE ATT
2 BE G Limit
3 Bass Center ATT
4 Bass Vol 0 MIN
5 Bass Vol 60 MIN
6 Bass Vol 60 Center
7 Bass Vol 0 MAX
8 Bass Vol 60 MAX
19 [SOUND 9]
1 Treble Center ATT
2 Treble Vol 0 MIN
3 Treble Vol 60 MIN
4 Treble Vol 60 Center
5 Treble Vol 0 MAX
6 Treble Vol 60 MAX
7 VS Path
8 VS Option
9 VS SP Interval
10 VS Width
11 VS Input Gain (2ch)
20 [SOUND 10]
1 Bass AGC
2 Bass Harmonics
3 Bass LPF Fc
4 Bass HPF Fc
5 Bass AGC Max
6 Bass AGC Min
7 Bass AGC Attack Time
8 Bass AGC Release Time
9 Bass AGC Threshold
10 Bass AGC HPF F0
11 Bass Harmonics Level
12 Bass Harmonics LPF F
13 Bass Harmonics HPF F
21 [M PWM]
1 PANNEL SELECT
2 PWM
3 PWN FREQ
4 PWM DUTY
5 OSC FREQ
6 OSC DUTY
22 [M BRI DA1]
1 BRIGHTNESS DA0
2 BRIGHTNESS DA1
3 BRIGHTNESS DA2
4 BRIGHTNESS DA3
5 BRIGHTNESS DA4
6 BRIGHTNESS DA5
7 BRIGHTNESS DA6
8 BRIGHTNESS DA7
9 BRIGHTNESS DA8
10 BRIGHTNESS DA9
11 BRIGHTNESS DA10
12 BRIGHTNESS DA11
5–9
LC-37D44U
Page Line Item Description Remarks (adjustment detail, etc.)
23 [M BRI DA2]
1 BRIGHTNESS DA12
2 BRIGHTNESS DA13
3 BRIGHTNESS DA14
4 BRIGHTNESS DA15
5 BRIGHTNESS DA16
6 BRIGHTNESS DA17
7 BRIGHTNESS DA18
8 BRIGHTNESS DA19
9 BRIGHTNESS DA20
10 BRIGHTNESS DA21
11 BRIGHTNESS DA22
24 [M BRI DA3]
1 BRIGHTNESS DA23
2 BRIGHTNESS DA24
3 BRIGHTNESS DA25
4 BRIGHTNESS DA26
5 BRIGHTNESS DA27
6 BRIGHTNESS DA28
7 BRIGHTNESS DA29
8 BRIGHTNESS DA30
9 BRIGHTNESS DA31
10 BRIGHTNESS DA32
25 [M ADL1]
1 OPC33 ADLEVEL 0
2 OPC33 ADLEVEL 1
3 OPC33 ADLEVEL 2
4 OPC33 ADLEVEL 3
5 OPC33 ADLEVEL 4
6 OPC33 ADLEVEL 5
7 OPC33 ADLEVEL 6
8 OPC33 ADLEVEL 7
9 OPC33 ADLEVEL 8
10 OPC33 ADLEVEL 9
11 OPC33 ADLEVEL 10
12 OPC33 ADLEVEL 11
26 [M ADL2]
1 OPC33 ADLEVEL 12
2 OPC33 ADLEVEL 13
3 OPC33 ADLEVEL 14
4 OPC33 ADLEVEL 15
5 OPC33 ADLEVEL 16
6 OPC33 ADLEVEL 17
7 OPC33 ADLEVEL 18
8 OPC33 ADLEVEL 19
9 OPC33 ADLEVEL 20
10 OPC33 ADLEVEL 21
11 OPC33 ADLEVEL 22
27 [M ADL3]
1 OPC33 ADLEVEL 23
2 OPC33 ADLEVEL 24
3 OPC33 ADLEVEL 25
4 OPC33 ADLEVEL 26
5 OPC33 ADLEVEL 27
6 OPC33 ADLEVEL 28
7 OPC33 ADLEVEL 29
8 OPC33 ADLEVEL 30
9 OPC33 ADLEVEL 31
5 – 10
LC-37D44U
Page Line Item Description Remarks (adjustment detail, etc.)
28 [M V6THE]
1 V6 OS THERMO 1
2 V6 OS THERMO 2
3 V6 OS THERMO 3
4 V6 OS THERMO 4
5 V6 OS THERMO 5
6 V6 OS THERMO 6
7 V6 OS THERMO 7
29 [M V5THE]
1 V5 OS THERMO 1
2 V5 OS THERMO 2
3 V5 OS THERMO 3
4 V5 OS THERMO 4
5 V5 OS THERMO 5
6 V5 OS THERMO 6
7 V5 OS THERMO 7
30 [M TEMP]
1 BL TEMP1
2 BL TEMP2
3 BL TDUTY
31 [M EEP SET]
1 MONITOR TIME OUT
2 MONITOR MAX TEMP
3 MONITOR ERROR CAUSE RESET
32 [M TESTPTRN]
1 LCD TEST PATTERN
2 TV TEST PATTERN 1
3 TV TEST PATTERN 2
33 [MEMORY CLR]
1 KEY LOCK (1217)
2 KOUTEI AREA ALL CLEAR
3 A MODE AREA CLEAR
4 BACKUP AREA CLEAR
5 B MODE AREA CLEAR
6 EXECUTION
34 [ETC]
1 EEP SAVE Writing setting values to EEPROM.
2 EEP RECOVER Reading setting values from EEPROM.
3 STANDBY CAUSE RESET Reset stand by cause.
4 SETTING FOR ADJ
5 PANEL SIZE
6. Special features
* STANDBY CAUSE (Page 1/34)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 34/34)
Storage of EEP adjustment value
* EEP RECOVER (Page 34/34)
Retrieval of EEP adjustment value from storage area
5 – 11
LC-37D44U
7. Code list for Standby Cause
5 – 12
LC-37D44U
8. Signal adjustment
8.1. Checking the Device
Before starting the adjustment, make sure the adjustment tool and signal generator are set for Sharp LCD US.
Checking the signal generator level adjustment (Set to the standard level.)
2 Automatic adjust- Move the cursor to [ N358 ALL ADJ] and press the [ENTER] key.
ment execution When [ N358 ALL ADJ OK] appears, the adjustment is complete.
2 Automatic adjust- Move the cursor to [ COMP 15K ADJ] and press the [ENTER] key.
ment execution When [ COMP 15K ADJ OK] appears, the adjustment is complete.
5 – 13
LC-37D44U
8.5. Component 33K signal adjustment
2 Automatic adjust- Move the cursor to [ COMP 33K ADJ] and press the [ENTER] key.
ment execution When [ COMP 33K ADJ OK] appears, the adjustment is complete.
2 Automatic adjust- Move the cursor to [ ANALOG RGB ADJ] and press the [ENTER] key.
ment execution When [ ANALOG RGB ADJ OK] appears, the adjustment is complete.
2 Automatic adjust- Move the cursor to [ TUNER VCHIP TEST (*07ch)] and press the [ENTER] key. (*
ment execution Select the channel according to the RF signal.)
When [ A-OK(***.**)/VM-OK] appears in blue, the test is complete. (If [A-NG/VM-NG]
appears in yellow or red, the test is incomplete.)
Make sure a displacement of ± 0.0625 MHz from the center frequency is acceptable.
5 – 14
LC-37D44U
9. White balance adjustment
9.1. White balance adjustment
Writing
MSET0003
5 – 15
LC-37D44U
9.2. Key writing
EDID writing (Main PWB: QPWBXE450WJZZ, analog RGB input terminal / HDMI input terminal)
5 – 16
LC-37D44U
9.3. Adjustment sequence (adjustment according to the G adjustment value of gradation 6)
* Make sure the adjusting point gradations are correct since they are different for each model.
PC Set
Set the light level to MAX with the light control command
(SBSL0016 for 45).
SBSL0016
Setting is complete.
OK
Initialization is done.
OK
Pattern display
Adjustment values are set.
OK
Pattern display
Adjustment values are set.
OK
Correction of G value
MG5GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
WBI5) x 2 x (the ratio).
5 – 17
LC-37D44U
PC Set
Start measurement
Adjust RB to the target xy values.
MG5RXXXX
MG5BXXXX
* XXXX indicates the adjusted values between 0000 and 1023
(4 digit decimal number with zero fill).
* G is fixed.
Repeat until RGB * The default adjustment value of RGB is the parameter value
become the target of the WBI5 command multiplied by 2.
values.
The adjustment value is
reflected in the image.
Pattern display
Adjustment values are set.
OK
Correction of G value
MG4GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
WBI4) x 2 x (the ratio).
Start measurement
Pattern display
Adjustment values are set.
OK
Correction of G value
MG3GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
WBI3) x 2 x (the ratio).
5 – 18
LC-37D44U
PC Set
Start measurement
Pattern display
Adjustment values are set.
OK
Correction of G value
MG2GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
WBI2) x 2 x (the ratio).
Start measurement
Pattern display
Adjustment values are set.
OK
Correction of G value
MG1GXXXX
When G is changed at gradation 6, calculate the ratio of the
change and set the following value to XXXX: (the value set with
WBI1) x 2 x (the ratio).
5 – 19
LC-37D44U
PC Set
Start measurement
Writing is complete.
OK
Deletion is complete.
OK
Completion of adjustment
5 – 20
LC-37D44U
10. Factory settings
After making the factory settings, pull off the AC cord.
NOTE: Do not turn on the power once the factory settings have been made. Otherwise the factory settings must be made again.
5 – 21
LC-37D44U
CHAPTER 6. TROUBLE SHOOTING TABLE
LC-37D44U
Service Manual
Is INPUT-1 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Is the video signal detection function normal? Is the video signal detection function normal?
Check the line between pin(2) of J501 and pin AD4 of Check the line between pin(2) of J503 and pin AC6 of
IC8001 IC8001
YES YES
Is video signal fed to AN16 of IC8001 via L.P.F composed of Is video signal fed to AN17 of IC8001 via L.P.F composed of capacitor and
capacitor and inductor between Q511 and Q521? inductor between Q512 and Q522?
NO NO
Check the line between pin(3) of J501 and pin AN16 of Check the line between pin(3) of J503 and pin AN17 of
IC8001. IC8001.
YES YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, D5~7, and E5~7 of IC8001?
NO
Check the line between IC8001 and IC5103.
Check IC8001 and peripheral circuits.
YES
Are digital video (RSDS) signals sent from IC5103 to SC5201 and NO Check the line between IC5103 and SC5201 and SC5202.
SC5202?
6–1
LC-37D44U
No video (1)
Is INPUT-1 selected on the input select menu screen? Is INPUT-3 selected on the input select menu screen?
NO NO
Is the video signal detection function normal? Is the video signal detection function normal?
Check the line between pin(2) of J502 and pin AC7 of Check the line between pin(2) of J509 and pin AE1 of
IC8001 IC8001
YES YES
Are component video signals fed to pins AM21, AN21 and Are component video signals fed to pins AN22, AP22 and
AL21(Y,PB,PR) of IC8001 via each L.P.F composed of capacitor AL22(Y,PB,PR) of IC8001 via each L.P.F composed of capacitor and
and inductor between (Q501,Q506,Q504) and (Q515,Q516,Q517) inductor between (Q502,Q503,Q505) and (Q518,Q519,Q520) respec-
respectively? tively?
NO NO
Check the line between each pin of J502 and each Check the line between each pin of J509 and each input pin
input pin of IC8001. of IC8001.
YES YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, D5~7, and E5~7 of IC8001?
NO
Check the line between IC8001 and IC5103.
Check IC8001 and peripheral circuits.
YES
Are digital video (RSDS) signals sent from IC5103 to SC5201 and NO Check the line between IC5103 and SC5201 and SC5202.
SC5202?
6–2
LC-37D44U
No video (3)
NO
Is the video signal detection function normal?
Check the line between pin(6) of J504 and pin AE2 of
IC8001
YES
Are Y and C signals fed to pins AL17 and AL16 of IC8001 via L.P.F com-
posed of capacitor and inductor between (Q513,Q514) and (Q523,Q524)
respectively?
NO
Check the line between J504 and IC8001.
(Q513,Q524,etc)/(Q514,Q524,etc)
YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, D5~7, and NO Check the line between IC8001 and IC5103.
E5~7 of IC8001?
6–3
LC-37D44U
No video (4)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Is video signal fed to AM19 of IC8001 via a buffer amplifier? Are there the video signal outputs (IF_OUT_P/N) at the pins(19) and (20)
of tuner(TU1101)?
NO NO
Check TU1101 and its peripheral circuits(SDA3/ Check TU1101 and its peripheral circuits (SDA/
SCL3, etc.). SCL3, etc.).
Check the line between AM19 of IC8001 and pin Check the line between (AM33, AM34) of IC8001
13 of TU1101 (Q510, etc.). and (pin(19), pin(20)) of TU1101.
YES YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, D5~7, and E5~7 of IC8001?
NO
Check the line between IC8001 and IC5103.
Check IC8001 and peripheral circuits.
YES
Are digital video (RSDS) signals sent from IC5103 to SC5201 and NO Check the line between IC5103 and SC5201 and
SC5202? SC5202.
6–4
LC-37D44U
HDMI: No external input video [INPUT-4] HDMI: No external input video [INPUT-5]
Is INPUT-4 selected on the input select menu screen? Is INPUT-5 selected on the input select menu screen?
NO NO
Select INPUT-4 on the input select menu Select INPUT-5 on the input select menu screen for the
screen for the right input signal. right input signal.
Does the HOT PLUG detection function? Does the HOT PLUG detection function?
Does the DDC5V signal come from pin(18) of Does the DDC5V signal come from pin(18) of SC1602 to
SC1601 to pin(72) of IC1604(HDMI-SW)? pin(52) of IC1604(HDMI-SW)?
NO NO
Check the line between Check the line between the input ter-
the input terminals of minals of SC1602 and IC1604.
SC1601 and IC1604.
YES YES
Does the HPD signal come from pin(56) of Does the HPD signal come from pin(36) of IC1604 to
IC1604 to pin(19) of SC1601? pin(19) of SC1602?
NO NO
Check the line between Check the line between IC1604 and
IC1604 and SC1601. SC1602.
IC1604 pin(56) IC1604 pin(36)
YES YES
IC1607 pin(4) IC1608 pin(4)
SC1601 pin(19) SC1602 pin(19)
Are there the TMDS signal inputs at pins(58/59)(CLK-/+), (61/ Are there the TMDS signal inputs at pins(38/39)(CLK-/+), (41/42)(D0-/+),
62)(D0-/+), (64/65)(D1-/+), (67/68)(D2-/+), all of IC1604? (44/45)(D1-/+), (47/48)(D2-/+), all of IC1604?
NO NO
Is IC1601(EEPROM) accessed by I2C, with Is IC1603(EEPROM) accessed by I2C, with HDMI con-
HDMI connected, to read the DDC_I2C SCL/ nected, to read the DDC_I2C SCL/SDA data?
SDA data?
NO NO
Check the DDC line and its peripheral cir- Check the DDC line and its peripheral circuits.(IC1603 and
cuits.(IC1601 and its peripherals). its peripherals).
YES YES
Are there the TMDS signal inputs at pins(AM1/AM2)(CLK-/+), (AN1/AN2)(D0-/+), (AM3/AM4)(D1-/+), (AP2/AN3)(D2-/+), all of IC8001(CPU)?
NO
Check IC1604, IC8001 and their peripheral circuits.
YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, D5~7, NO Check the line between IC8001 and IC5103.
and E5~7 of IC8001?
6–5
LC-37D44U
No video (6)
NO
Select INPUT-6 on the input select menu
screen for the right input signal.
YES
Are digital video (LVDS) signals sent from pins B5~7, C5~7, NO Check the line between IC8001 and IC5103.
D5~7, and E5~7 of IC8001?
6–6
LC-37D44U
No audio (1)
Is INPUT-1 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” on the Is the audio output selected for “VARIABLE” on the
menu screen? menu screen?
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Does the audio signal come from pins(5)(L) and (7)(R) of input termi- Does the audio signal come from pins(5)(L) and (7)(R) of input termi-
nal(J501) to pins(35)(L) and (36)(R) of IC1403(CODEC)? nal(J503) to pins(37)(L) and (38)(R) of IC1403(CODEC)?
NO NO
Check the line between J501 and IC1403. Check the line between J503 and IC1403.
YES YES
Does the audio signal come from pins(4)(COD_LRCK), (5)(COD_BCK) and (6)(COD_SDOUT) of IC1403 to pins(AK24), (AH24) and (AJ24) of
IC8001(CPU)?
NO
Check the line between IC1403 and IC8001.
YES
Does the audio signal come from pins(AN28)(SPOUT_LP), Check the line between IC8001 and IC2701, and their
(AN29)(SPOUT_RN), (AP28)(SPOUT_LN), and(AP29)(SPOUT_RP) of NO peripheral circuits. (AMP_MUTE line, etc.)
IC8001 to pins(5)(SP_LP),(6)(SP_LN), (8)(SP_RN), and (9)(SP_RP) of
IC2701(AMP)?
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
6–7
LC-37D44U
No audio (1)
INPUT-3 No audio
NO
Is the audio output selected for “VARIABLE” on the menu
screen?
Set the audio output to “FIXED”.
YES
Does the audio signal come from pins(2)(R) and (4)(L) of input termi-
nal(J506) to pins(40)(L) and (41)(R) of IC1403(CODEC)?
NO
Check the line between J506 and IC1403, and their periph-
eral circuits.
YES
Does the audio signal come from pins(4)(COD_LRCK), (5)(COD_BCK) NO Check the line between IC1403 and IC8001.
and (6)(COD_SDOUT) of IC1403 to pins(AK24), (AH24) and (AJ24) of
IC8001(CPU)?
YES
Does the audio signal come from pins(AN28)(SPOUT_LP), Check the line between IC8001 and IC2701, and their
(AN29)(SPOUT_RN), (AP28)(SPOUT_LN), and(AP29)(SPOUT_RP) of NO peripheral circuits. (AMP_MUTE line, etc.)
IC8001 to pins(5)(SP_LP),(6)(SP_LN), (8)(SP_RN), and (9)(SP_RP) of
IC2701(AMP)?
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
6–8
LC-37D44U
No audio (2)
[HDMI analog audio input] INPUT-5 No audio [PC analog audio input] INPUT-6 No audio
Is INPUT-5 selected on the input select menu screen? Is INPUT-6 selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” on Is the audio output selected for “VARIABLE” on the
the menu screen? menu screen?
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Does the audio signal come from pins(2)(R) and (4)(L) of input termi- Does the audio signal come from pins(2)(L) and (3)(R) of input termi-
nal(J507) to pins(43)(L) and (44)(R) of IC1403(CODEC)? nal(J508) to pins(46)(L) and (47)(R) of IC1403(CODEC)?
NO NO
Check the line between J507 and IC1403, and Check the line between J508 and IC1403, and their
their peripheral circuits. peripheral circuits.
YES YES
Does the audio signal come from pins(4)(COD_LRCK), (5)(COD_BCK) and (6)(COD_SDOUT) of IC1403 to pins(AK24), (AH24) and (AJ24) of
IC8001(CPU)?
NO
Check the line between IC1403 and IC8001.
YES
Does the audio signal come from pins(AN28)(SPOUT_LP), Check the line between IC8001 and IC2701, and their
(AN29)(SPOUT_RN), (AP28)(SPOUT_LN), and (AP29)(SPOUT_RP) of NO peripheral circuits. (AMP_MUTE line, etc.)
IC8001 to pins(5)(SP_LP),(6)(SP_LN), (8)(SP_RN), and (9)(SP_RP) of
IC2701(AMP)?
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
6–9
LC-37D44U
No audio (3)
No audio at UHF/VHF broadcast signal reception No audio at digital broadcast signal reception
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Is the audio output selected for “VARIABLE” on the Is the audio output selected for “VARIABLE” on the menu
menu screen? screen?
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is there the SIF signal output at pin(15) of tuner(TU1101)? Are there the video signal outputs (IF_OUT_P/N) at the pins(19) and (20)
of tuner(TU1101)?
NO NO
Check the tuner(TU1101) and its peripheral circuits. Check the tuner(TU1101) and its peripheral circuits.
YES YES
Does the SIF signal come from pin(15) of tuner(TU1101) to Does the video signal outputs come from pins(19) and (20) of
pin(AN23) of IC8001? tuner(TU1101) to AM33 and AM34 of IC8001?
NO NO
Check the line between TU1101 and IC8001. Check the line between TU1101 and IC8001.
(Q1101,Q1102, etc.)
YES YES
Does the audio signal come from pins(AN28)(SPOUT_LP), (AN29)(SPOUT_RN), (AP28)(SPOUT_LN), and (AP29)(SPOUT_RP) of IC8001 to
pins(5)(SP_LP),(6)(SP_LN), (8)(SP_RN), and (9)(SP_RP) of IC2701(AMP)?
NO
Check the line between IC8001 and IC2701, and their periph-
eral circuits. (AMP_MUTE line, etc.)
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
6 – 10
LC-37D44U
If no video appears, refer to “No external input video (HDMI) Are there the video signal outputs (IF_OUT_P/N) at the pins(19) and (20)
[INPUT-4/5]”. of tuner(TU1101)?
NO
Is the HDMI_MUTE line as specified? Check the tuner(TU1101) and its peripheral circuits.
NO YES
Check Q1301, IC1302 and their peripheral circuits. Does the video signal outputs come from pins(19) and (20) of
tuner(TU1101) to AM33 and AM34 of IC8001?
NO
Check the line between TU1101 and IC8001.
YES YES
Is there the SPDIF signal (OPT_OUT) output at pin(AP11) of IC8001(CPU)?
NO
Check the IC8001 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin(2) of IC1304 NO Check the line between IC8001 and IC1304.
(SPDIF_BUFF & MUTE)?
YES
Is there the MUTE signal input at pin(1) of IC1304? NO Check the MUTE_A_ALL and ACDET signals, and their
peripheral circuits. (Q1304, Q1312, D1310, etc.)
YES
Is there the SPDIF signal input at pin(1) of D1306(OPTICAL OUTPUT)? NO Check D1306 and its peripheral circuits.
6 – 11
LC-37D44U
No audio (4)
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
[INPUT-5 input]
Is INPUT-5 selected on the input select menu screen?
NO
Is the audio output selected for “VARIABLE” on the
menu screen?
Set the audio output to “FIXED”.
YES
[INPUT-4 input] If no video appears, refer to “No external input video
(HDMI) [INPUT-4]”.
[INPUT-5 input] If no video appears, refer to “No external input video
(HDMI) [INPUT-5]”.
YES
Is the HDMI_MUTE line as specified?
NO
Check Q1301, IC1302 and their peripheral circuits.
YES
Does the audio signal come from pins(AN28)(SPOUT_LP), Check the line between IC8001 and IC2701, and their
(AN29)(SPOUT_RN), (AP28)(SPOUT_LN), and (AP29)(SPOUT_RP) NO peripheral circuits. (AMP_MUTE line, etc.)
of IC8001 to pins(5)(SP_LP),(6)(SP_LN), (8)(SP_RN), and (9)(SP_RP)
of IC2701(AMP)?
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector(P2701), speakers and their peripheral circuits.
6 – 12
LC-37D44U
Is the audio output from the monitor set at “VARIABLE” or “FIXED” NO Check the bus line(SCL0/SDA0) and IC1403.
on the menu screen?
YES
Are there the audio signal outputs at pins(24)(LINE_L) and NO Check IC1403 and its peripheral circuits.
(25)(LINE_R) of IC1403(CODEC)?
YES
Does the audio signal come from pins(24)(LINE_L) and NO Check the line between IC1403 and J505. and their periph-
(25)(LINE_R) of IC1403 to pins(2)(R) and (4)(L) of J505? eral circuits.
6 – 13
LC-37D44U
250ms 1sec
L: Off
Monitor temperature failure If the panel temperature is 60°C or more for 15 seconds or
Flashes 5 times H: On more in a row, CAUTION appears on the OSD of AVC
(flashes in red in the lower right screen).
L: Off If the panel temperature is 60°C or more for 25 seconds or
more in a row, error standby is activated.
(MONITOR MAX TEMP on process A mode: Change of tem-
perature failure AD value): Thermistor
Illegal Flash ROM Data Flash ROM of Monitor Microprocessor is illegal.
Flashes 8 times Update Monitor Microprocessor Software again.
H: On
L: Off
6 – 14
LC-37D44U
2)Power failure details (Power LED flashes twice and OPC LED flashes)
Pins are monitor microprocessor pins unless otherwise
Error type OPC green LED operation (1 cycle)
specified.
PS_ON DET_POW1 (pin 34). Main converter 13V/UR10V is not
13V/UR10V failure H: On applied.
Flashes once If error is detected during operation, the power is turned on
L: Off again by interrupt handling (instantaneous blackout process-
ing).
EU_POW DET_POW3 (pin 36): Abnormal (L). Main power 3.3V is not
Main 3.3V failure H: On applied.
Flashes twice If error is detected during operation, error standby is activated
L: Off by polling.
3)Communication failure details (Power LED flashes 3 times and OPC LED flash
Basically, communication logs are analyzed by a bus
Error type OPC green LED operation (1 cycle)
monitor or debug print logs are analyzed.
Initial communication reception failure Initial communication from the main CPU is not received.
Flashes once H: On (After canceling the reset, request for the monitor model No.
is not received.) → Communication line failure or main CPU
L: Off start-up failure
Time-out setting reception failure Time-out setting and start-up mode change cannot be
Start-up confirmation reception failure H: On received from the main CPU. (Start-up communication until
Flashes twice time-out setting and start-up mode change is not received.) →
L: Off Main CPU start-up failure or monitor microprocessor's recep-
tion failure
Regular communication failure Regular communication that is performed at 1 second inter-
Flashes 3 times H: On vals in the normal operation is interrupted. → Main CPU oper-
ation failure or monitor microprocessor's reception failure
L: Off
6 – 15
LC-37D44U
CHAPTER 7. MAJOR IC INFORMATIONS Service
LC-37D44U
Manual
7–1
LC-37D44U
CHAPTER 8. OVERALL WIRING/BLOCK DIAGRAM
LC-37D44U
Service Manual
I
INVERTER
UNIT
KEY UNIT KM 㪌
㪈
1 POWER
LB UNIT
9
1
H
1 To LAMP
QCNW-G729WJQZ : KM FPC FPC PD
23 To LAMP
12
B to B
G 1㵘㵘㵘 㵘㵘㵘80 1㵘㵘㵘 㵘㵘㵘80
㪋㩷㩷㩷㪈 KM
DIGITAL
AUDIO
INPUT 6
MAIN UNIT To LAMP
OUTPUT ANALOG
OUTPUT
RGB
(PC IN)
7
HDMI
L
L
INPUT 5
LB 1 To LAMP
F AUDIO
AUDIO
R INPUT 4
R HDMI
AUDIO
QCNW-G732WJQZ : PD + LB
PB PB L
L
L 12 To LAMP
AUDIO AUDIO AUDIO
PR PR
R
R
R
PD
D
1 To LAMP
ANT/CABLE
USB (SERVICE)
R
AC IN
SP
BUS-CONE (4pin)
QCNW-G730WJQZ : RA
A QCNW-G731WJQZ : SP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–1
LC-37D44U
[2] SYSTEM BLOCK DIAGRAM
/#+0 㪠㪚㪌㪉㪇㪈
㪣㪚㪛
+% 㪠㪚㪌㪉㪇㪉
+% 㪭㪚㪦㪤 㪧㪘㪥㪜㪣
I %8$5.4 %8$5A 20.A+%A' +%59 㪙㪬㪌㪌㪇㪋㪈 㪛㪘㪚
㪙㪛㪏㪈㪋㪊㪤
㪠㪚㪌㪈㪇㪈
, .4A 㪬 㪜㪜㪧㪩㪦㪤
+0276 㪤㪉㪋㪉㪌㪍㪙
%QORQPGPV ;2D2TA
&4+8'4
,
((%
((%
%8$5.4 %8$5A .8&5
DKVEJ
45&5(2%
+0276 , .4A
5 㪠㪚㪌㪈㪇㪊
, 5 5*+2A'020'.A'0 㪫㪄㪚㪦㪥
㪜㪘㪞㪣㪜㪉
((%
((%
.4 45&5(2%
+0276 , .4A
%QORQPGPV ;2D2TA
H ,
8 㪠㪚㪌㪋㪇㪈
#/2A/76' 㪧㪦㪮㪚㪫㪩㪣
56#0&$; 748 㪙㪛㪏㪈㪍㪉㪜㪢
㪠㪚㪉㪎㪇㪈
䇼㪪㪧䇽 2416'%6 $7
8
㪪㪧㩷㪘㪤㪧
㪧㪉㪎㪇㪈 +%
52 㪜㪯㪫㪄㪪㪧
㪰㪛㪘㪈㪋㪎㪪㪱
4GUGV
456A*(.5A%2.&
(TQO%27 (.#5A9A%2.&
&'6A20.8
45A$7(A%06
2 +08'46'4 $.
G %QPPGEVQTHQT
5QHVYCTGYTKVKPI
#WFKQ1WV .4 &KUENGVG 41/5'.
&KUENGVG
+1
56$
4Z&6Z& +1 8QP
8 (TQO%27
56$A%27
ޣ.$ޤ%0
RKP
ޣ.$ޤ2
RKP
+% +%
8
8 )CVG
+%
YKTGR
67 670A%8$5 +% 9*(7 +%
*&/+A/76'
#PCNQI .+0'A/76' +1 4Z&6Z& /% ''241/A5%.5&#
4(+0 &KIKVCN #(6 / +%
-*\8 7#46 /QPKVQT/KEQO $7
8
6WPGT 6JGTOKUVQT 6*'4/1 +% 1(.
#& 92 ''241/
#(6 #& 5%5,
5+( '44A20.
F
#)%#(6
65+0176
+%A %8$55;2D2T
8 +% /*\ /*\
+%
+%
-*\8 #%A&'6
.8&5176
+%A 866 :VCN
&A+(
+%A
8
+%
-*\8 2/A4'3%$1165 +1
+%A +1
8 +% 0A54'5'6 +1
+(KP &&4
5+( #)%#(6 /D
+06 #& +1 +1 +1
*&/+KP %08UU
8
8
8 *8
+0 +% 4)$KP
.4A 1(. ޣ2)ޤ
+0 52176A.4
+% 176
R
.4A +%
+0 %1&'%
.4A #-#' 219'4
8
8
E $75
%10'%614
6Z&4Z& *&/+A.4
+0 176
$%/
9:)#
8
+0
4)$A.4 .+0'A.4
+0 176 /*\ &KIKVCN#8FGEQFG/CKP%27 2
:: VCN %QPPGEVQTHQT
&'6A8&'6A8
*&/+A.4 /*\ &GDWI
*&/+#WFKQ
0A456A%1&'%
+5 +5
4)$#WFKQ 4)$A.4 %1&A5&176
/KPK2NWI %1&A.4%-%1&A$%-
: VCN &52A5&+0&52A5&+0 &68+5
/*\ $WHHGT &52A/%.-&52A$.-+0&52A.4%-
.QECN$752%+
126+%#.
8A# 126A176 52&+(
176 &6852&+(
D +% /WVG
8 +% 4'5'6A176D
12%A.'&219A.'&A4219A.'&A).'&A;1;#-7
7#46#
7#46$
7#46%
75$A
75$A
''241/ \\
6Q456QHGCEJ+% 0A%27A456
+0276 &57$ *&8& MDKV 4'5'6
4)$ 4)$
+%
-*\
+% 0A54'5'6
''241/
0A&$)A456
25A10
+0276 *&/+ +%
-*\8
5% 4:AZ /*\ $CEM7R
˴$7
8
#%A&'6
#% 5VCPFD[ $7㨢
+%
8+% +%
8 $7
8
''241/ 6/&559 ''241/ 25A10
ޣ2&ޤ219'4˴%0
RKP
+%
ޣ2&ޤ219'4˴2
RKP
+0276 *&/+ 5++ *&%2 +08'46'4
-';-';56#0&$;219
5% 4:AZ ''241/ +P /#+0
8 2(%
2 ˴#8 /#+0
+P +%
C
˴8
%QPPGEVQTHQT (.#5*
YKTGR
˴&8 748 X
+P 5QHVYCTGYTKVKPI /D ˴&8
5GNA ˴&8 $78 74
X
㧔20.X㧕
20.219
4%
12%
&219
20.A10
$7
8 (TQO%27
2QYGTUWRRN[EKTEWKV
,
B 75$
ޣ4#ޤ2
R ޣ-/ޤ2
R ޣ#%ޤ
R
ޣ4#ޤ2
R ޣ-/ޤ2
R
.'& -';
A 4%
12%
.'&
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
8–2
LC-37D44U
CHAPTER 9. PRINTED WIRING BOARD ASSEMBLIES
LC-37D44U
Service Manual
R140
C103
C111
3 C104 R126 R120
R107 C108
R108
Q106
Q102
C107 R104 R121 R124
R119 P101 P102
RMC102
C110
R103
IC102
R139
RMC101 IC101 D103 D114 D115
R132
R135 R109
D101
D116
Q103
Q105
C105
R110
C101
R117
R137
R127
R122
R101 R136 Q104
C102 R102 R138 R116
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–1
LC-37D44U
[2] KEY Unit
D
KEY Unit (Side-A Chip)
C R154 D155
R153
S153
S155
S151
S152
S156
S157
S154
D152
D151
R151
R152 P151
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–2
LC-37D44U
[3] MAIN Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–3
LC-37D44U
H
MAIN Unit (Side-A Chip)
R1616
C2224 R2245 C2225
R2244
Q1606
D1604
D2206
FB1605
D2207
Q1603
C2217
R2243
R2240
Q2210
R2241
Q2211
R2249 P2001
LUG2201
SC5201 SC5202
C2218
C1611
LUG2211
C2223
IC1603 IC2001
D2205
P2002 C1612
R1601 R1724
C2220 R2250
P9202
C2221
C2222
R2247
R1609
R2248
R2246 R2254
R2253
R2256
R2239
R9201
R2257 R2251 R1624 R2040 R2010
C2219
FB2001
13
R1685
R1687
R2305
R2255
R2304
L1301
C2029
C2028
C2027
Q1609 R1640
C1617
Q2212
R2258 FB2005 L5108
Q1618
G SG1601
C5125 L5107
C1618
FB2004
FB2003
L5109
SC1602
D1306
IC1606
C5132 L5106
R582
L5110
C1642
C1312 SG1613
C5120
R581
R1686
R2009
R2008
Q1620
C1313
C5131
C570
LUG2209
FB2204 SG1608
R600 SG1614 C5117
L5113 L5103
R601
C1310 R1311 FB2203
R578 C582 SG1620 R1739 C5129
IC1304
R5492
R5493
R5490
R5489
IC1609
C581 R1610 R1741
R586
R1667
R587 L5101
R1608
FB5103
R1742
C1626
C1629 C1627
R605
R604
C5142
R5486 R5484
C5135
C2020 R2029
Q1602
Q1605
SC2201
C5457
C5456
C5455
R2016
R5503
R5502
R5501
R5498
R5499
R5496
R5494
Q1312
R1333
C585
R1612
FB525
J505
J507
C571 D1603 R1743 R2018
Q509 R5482
IC2008
IC1607
C586
R584
R2058 C5128
C1628
R1744
C2026
R1729
FB5101
C5452
C5133
R2066
C5136
D2201
R2605
R2623
R1745 IC2004 R5481
R5148
R583 C579
R5491
C2603
R1746 C5127 C5126
R2015
D2003
C1677
R1603 R1723
C580 C1675 R5487
R1670
R1674
Q507 C1674 C2606
IC5402
C1633 C1637
R598 C5130 C5113
R5485
R1678
R1679
R1681
R1605
C1613 C1632 R2011
R2230 FB2207
R2226 FB2206
C2017
C2018
R1606
P2603
R2621
R599
FB501
R576
R1682
R1680
FB522
C5134
F
R602 C1615
R1672
R1675
R5483
R2227
R2229
R2602 R2601
FB5102
C569
C5205
C5202
C5204
SC1601
C8138
C5139 C2601
R8042
R579
SG1609 C5141
D2203
D2202
C583 C5454
R580
R2234
R2233
SG1615 R5105
R5143
IC8003
R2031
C5144
R5202
C8144
R2238 SG1621 R5104
C8143
R5205
R5201
R5204
R5208 C5207
R608
R5142 C5458
SG1604
Q523
R8043 C5
R607 FB5105 10 C5107
D2211
D2210
C2214 C2213
R630
C550
TP2041
C5137
5
C5143
R556 C552 C5119 C5
SG1610
R5207
R5203
R5206
C5206
D519
1
R634
C5 06
IC2201
C5123
C547
C5121
R5479
R5478
R5480
R5476
SG1616 1
R633 C5 08
R2242
R612
R2252
R589
FB520
SG1622
C2228
C5138
R627
D520
R8024
C532 C559
R572
IC2202
R632
R5224 R5220
C560 D2208 R2262 TP8014 TP8051
C565
C5213
FB2208
R628
C545
D505
C548
R631
R5223 R5221
C2227
R2261
R553 C531 C562 TP8013 TP8048
R8901
C5214 IC5202
R5473
R8060
R5474
L510 TP8011 TP8015
D508 R5145
R2259
FB5104
R610
C554
C5102 C5217
Q5408 Q5409
C2216
R2237
LUG2205
C8128 C5114
D509
R2260 C5218
R503
D518
R5226
R611
R502
R8051
IC5102
C8127 R5231 R5229 C5219
C8120 R8143 C5112 R5230 C5220
D504 R9209 C5201
LUG2202 R9003 C5221
C5111
R5232
R5233
R5450
R504 C8110 R5236 R5235
C8111
C8113
C8121
C8123
C8122
C8124
R501 C8108 C5110 C5212
FL5101
Q513 C8148 R9007 R5222
D512
C8085
R517
R5115
R5121
E
C8118
R592 R606
R5211 R5214
C8133 C5215
IC5201
FB510
C8142 R5124
C8117 C8141 R5129 R5213
FB521
C546
D522
Q511
C525
C529
C8130 R5108
C563
R624
R8101
L507
R5127
R525 R526
C527
C507
Q521 C8131
R574
R5110 R5139
R622
R8102
FB502
Q502
P5101
R5109
R626 C8140 C5101
D521
R5112
R571
L504 R5111
R568
R609
C522 R5113 R5120
Q501
C544 C8139 R8006 R5106
Q515 R8094 R8128 R5117 R5119
C557 L5115
R613
R507
R8126 R5122
C510
C512
C536
Q518
R524 R523
FB516 C8126 R5107
L501
C517 R8127 L5116
R506
C8125
D517
C504
C558 R5123
R505
R538 R508 TP8044 R8125 L5118
R8021
R8040
R521 C8091 R8117 L5119
R615 R555 R5102
R2636
R558
Q506
R537 R534
D5409
C505 C513 C524
L5120
R562
D511 FB509 R510 FB518 Q516 C8107 TP8001
FB515
J509
J503
J502
J501
L502
C9001
D516
C534
C2236
Q5410
L2204 C8093
R518 FB505 C2238
9
L2
22
R561
R547 C539
IC8001 IC9001
R564
20
C2
C2240
D515
R509 L2 6
R544
20
FB512
R540
C2239 R8228
R616
C501
D
C2241
J506
FB513
C8134 R8215
R591 R8151 R8187
R519
1
Q517
C506 R8216
L503
L5403
FB517 C526 X8001 R8188
C537
Q519 R8246
R8099 C8136 R8230 L5401
R535
R536
R511
C535
R8005
R1408
R8045
FL
R8191 3 L9602
VA8001
VA8002
R1418
R8123 TP8043
80
R1415 C1415 R8138 R8259
R533
FB508
01
C8147
C523 R546 R8248
R1414 TP8016 R8132 R8233
C8150
C518 C530
Q520
R620
R8030
R8004
D510 FB8001 TP9304 TP8047 C8197 R8260
C509 TP8042 TP8010 R8035 R8027 5
Q505 C8001 1
TP8002
R520
C543 R621 R550 IC1403
R8120
C
R8002
R8018 R5101 R8028
J8001
L9603
2
R8135 IC8151
00
R1426
R2635
D8
Q2603
C1409
R8032 C8164 4
C8171
FB8004
R9012
C1408
R1423
C1419
C8166
R8090
R1404
R1405
R1406
C1407
P9701
R1120
R1121
R1407
R2313 R2314
L9641
Q1102
R557
C8165
R597
C8186
Q1101
C575
R595
C8460
C8461
P9002
C8462
R8475
R8474
Q510 L9601
C2710
R1115
R1113
R1114
B
R593
FB514
TU1101
C1107
R594 R1110 IC8452
IC8454
R1302
9
Q1309
R1335
Q1305
D1302
LUG2212
R1324
R1338 R1337
D2704
cam1
R1336
R1310
C2745
C2728
C2731
D1311 L2704 L2701
R1323
C2741
C2725
C2730
D1307
D1310
D1312
D2701
Q1304 D1304 FB2702
L1101
C2737
C2742
FB2703
R9035
R9034
C2744
D2703
C2726
C2738
10
C2740
P9301 LUG2206
TH2001
FB2704
P9001 P2701
D2702
LUG2210
C2743
L2703 L2702
P2201
A
C1108
C1110
C1109
C1111
R1117
R1107
R1105
R1104
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–4
LC-37D44U
H
MAIN Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–5
LC-37D44U
H
MAIN Unit (Side-B Chip)
TL5250 TL2013
C1676
R2007 R1730
R2003
C2002
R2072
R2035
R2025
TL9240 TL9224 TL9222 TL9208
D1614
D1619
TL5254 TL5255 TL5233
TL5205 TL2006
TL5253 TL5251 R9205 TL9201
R2068
TL5323
TL5322 TL5256 TL5252 TL5245 TL2014 TL9223
Q2001 Q2006 TL9241 TL9239 TL9221 TL9207 D1607 C2226
TL5321
TL5202 TL5203
TL2012
TL2007 IC1608
R9204
R9211
R9005
TL5320
R9208
TL5244 TL2003 TL2005
TL2001 TL9212TL2011TL2009
R1637
TL5307 TL5303 TL5249 TL5227 C2003
TL5302
R1641
TL5318 TL5248 R2039 Q2007 TL1618 L2202
R2076
TL5241 TL5201
R9207
TL5212 TL5208 TL5206 TL5204 R2030 TL9213 R2004 R9202
TL5258 TL5247 TL5243 TL2002 TL2004
TL5305 TL5217 TL9211 TP2014 R9008 TL1607
LUG2213
TL5319 TL5298 TL5257
IC2007
TL5294
R2052
R9305
R2019
TL5306 TL5237 TL5235 TL5230 TL9210 TL9206 R9212 TL1615
C1601
12 TL5304 TL5287
TL5285 TL5246 TL5242 TL5218 TL5209
TL1613 TL2290 TL2231
R2027
TL5239 TP2011 TL2303 TL9205
TL5301 TL5297 TL5293 TL9203 TL9202 TL1302
C2024
TL5286 TL5234 TL5211 TL9209 TL9219 R2012 C1645
C1638
C2005
C2014
TL5216 TL5210 TL5207 TL9204
R2005
R2013
R2002
R2024
R2023
R2071
R2050
TL5289 TL5240 TP2205
C2004
TL5308 TL5238 TL5226 TL1614 TL2291
TL5228 TL5215 C1640 C1634
FB1606
TL5300 TL5296 TL5292 TP2009
Q1619
C1620
TL5222 TL5220 R2017 TL545
R1668
R1611
TL5224 R2020
R1722
C1621
TL5267 TL5263 TL5259 TL2294
C1619 R1684
TL5311 TL5312 TL5273 R2006
C1622
TL5309 TL5231 R1671
TL5221 TL5219
R1737
C2007
TP1633
R2022
TL5275 TL5271TL5269 TL5265 TL5260 R2001
R1726
TL5314 TL5313 TL5281 TL5277 TL5223 TL1620
TL5272 TL5268 TL5264 C5124
C1652
TP2007
C1623
TL2028
R2028
TL5283 TL5261 TL2027 FB1603
TL5279 TL2015
R1677
R2032 R2046 R2047
TL5315 TL5274 TL5270 TL5266 TL5262 TL2030 R1683
TL5316 R2026 FB1607
TL5284 TL2029 TL638
TL5282 TL5280 TL5278
R2034 Q1616 C1607
R1676
R1738
TL5317 C2001 TL2263
R2036
C1625
C1624
TL1622
R1665
R1663
R1666
R1662
C2016 R2049
R2033 C1609
IC2002
X2002
TL639 TL2264 TL2262
C1679 TL1611
C2010 R1602 TL1303
C2006
TL2260
C1630
TL1616 D1601 TL2295
C1678
C1648
TL2017 IC1601
R2038
R1627
TL2018 TL2031 R1604 TL642
R1630 R1629 TL2261
R2042
TL2020 C1647 TL1609
C5118
D1611
D1613
TL2610 TL2667
D1605
TL2022 TL2040 TL2034
TL5416 TL5415 TL2037 TL2293
TL2604 TL2618 Q1607 TL637
TL2008 TL2039 TP2005 C1602
TL5414 TL641 TL544
R2603
F
TL5413
R2604 TL2025
TL2609 TL2666 TL2024
R2037
TL2669 FB2603 TL8046
TL2026
TL2601 TL8045
TL8043
TL552
C5449
TL8042
C8137
R5216
R5462
R5495
TL2297
C5216
R5497
C5461
C5460
C5447
TL547 TL548
R8144
R5239 FB8003
C5109 TL2296
C5223
R5149
R5240 R5238 C8080 R8146
R5242 R5237 R5241 D9302 TL555
C5226 C8064 TL556 TL557
TL8029 C8014 TL540 TL537
R8145
C2605
R5453
R5452
R5451
R5228
R5227
R2606 TL553
C2602 C8106
C8069
R2641
C8003
C8086
R5469
C8105 R8026
TL2654
Q5411
R8084
C8081 TL505
C2607
R5225 C2604
IC8002
E
C8039
TL5113 TL5112 TL5110 R8039
TL5101 R5455 11 TL516
IC2601
TL530
Q5401
R8136 C8112
TL5102 TL5111 TL5109 C8075 C8079 C8097 10
R2637 80 TL517 TL550
C5432
TL538
C8916 FB
R5468
TL5103 TL8093
09
R8 49
R5209 C2608 TL5108 TL5107 80 R549
1
R8100 TL518
C8
TL8092 FB
142
TL5104 R2640 R5454 08
R5103 C8909 C TL2226
C8 104
C8043 89 80 TL531
FB
C8
C8 98
C8 15
C8
C8062 TP8052
0
TL5105
91
90
9
C8059 C8036 5 07
4
TL525
10
C8076 04 7 C8
C8 027
C8037 C8 C8103 C8 13
9 80
C8
TL5106 FB
C8 038
TL5115 90 C8
C8096
0
C8044 3 91
04
C8 C8 2 R8056 R8903
90 90
FB8002 C8052 C8022 5 1
0
D5101 R8902
91
C8060
C5417
R5437
5
TL507
C8
C8911 TL534 TL503
09
8
C8026
C8
R5427 C8024 0
90
R5434 01
C8
C8
6
C8007 C8042 C8115
90
R5435 C8028 TL510
C5412
C8
4
C8025
R5429
C8061 C8005
90
TL533 TL502 TL506
R5436
R8029
C8
R5431 C8047 C8063 C8006
2
C8116
90
C8071
R5507
R5430 C8101
C8
R5438 C8004 C8083
C5463 R8129
2
C5462
R5426 TL511
C8077
TL526 TL527
10
C5416 C8011 TL519 TL520
31
C8
R5432
R81
R5467 R5439 C8016 C8032
6
05
C8034 C8023
R5440
C8078
C5418
C8
C5411 C8017 C8114
C5466
C5445
R5511
C8041
D5403
C8030
C5408
R5422
C8020 C8054
C5420
R5442 R5444
C5421
C5413 TL514
D5406 C5446 C8049 C8021 C8013 C8018 TP8046 TP8050 C8074 C8092
Q5414
C5414
C8220 C8058
D5410
C8084
R5443
D
C5440 Q5404 R8169
C5442 C5443
R5420
R5445
C8057
C5435
C5427 C8008
C5422 R5458 R5460 C5406 R5433 C8160
Q5413
C5444
D5405
R5457
C8029 R9014
R5408
R5406
C5405
R8171
R5464
C5403
R5407
C8046 R1431
C5459
C5434
C1429
R5404 R9313 TL536
C8194 C8170 C8222 TP9303
C5431
R5411
TP8020 R9324
R5414
R8270
C5430
C8156 R8140
R5405
C9613
C9622
C1426
R8208
C1430
C9602 R8010
IC9601
C1425
TL9701 C8192 R8036
TL9703 R9606
C9616 C8193 TL8080 TP8084
R9605 C8167
TL9710 C8168
C1428
C1431
R9604 TL9605 R8009
R9617 TL8048
C9625 R8116
C
TL8036
C1427
R9613 R9614 TL8047
R9616
C1432
C9710 R9609 D9606
C9612
TL9702
C9713 IC9605
R9629 R8055
D9607 TL8456 TL8050
TL9716
IC9703
C8157 TL8041
C9709
C9608 TL8072
C9718 Q5412 TL8069 TL8070
R9736
6
R9308
D9304
C5465
R9643
D5413
D9702
C9645
C9646
C9711
R9704
D9603
R5465 TL8078
IC9301
Q9301 R8025
R9739 C9642 TL9357 TL558
C9641 C9302
LUG2208
C8456
D9642 D9643
R9303
D9605
R9740
R9319
R9009
R9001
D9609
C9631
R9006
R9611
R9741
D9602 D9303
R9002
R9625 R8240 TL9001 D9001
C9719 C9619 R8227 TL8454 TL8455
D9601 C9708 R1330 R1318 TL9344 TL9004
TL9711 TL9724 R9612 IC9602 TL9002
C1411
C1308
C9604 C8451
C8453
C8452
TL9345
R8456
TL9603 TL9337
IC9704 R8243
C9624
C9618
IC1302
D9003
D9002
R1303
TL9346 TL9338
TL9003
R8457
B
TL8453
R1305
TL9339
R1403
R2709
R2706
R2710
R2707
R1421
D9713 TL9720 Q1301
C1404
C8209 TL9348
X1401
C9629 R1317 TL9340
C1417
R1450
R8244 R1328 R1326 TL9349
D1305 R1306 R1307 TL9341
R1402 R1401
C1314
C1405
C1418
R2719
Q1307
C8216 C1412
TL9350
R2753
R2754
R8242 TL9342
C8205
IC8451
TL9722
8
R1304 TL9351
C2704
C2705
C2706
C2707
IC1401
R2718 R1322
C8458
C8225
R1315
C2713
R1449
IC1301
IC1402
C2748
C1401
R1308
R1341
R1301
R2714
R2717
cam2
C2711 R1325
C2712
R8454
R8453
R8458
R8452
R9304
R8455
R8451
C1301 R9307
R2715
C1403
C2717
TL9316 TL9312
C2716
TL2701 TL9328
TL9334 TL9330 TL9324 TL9320
R2713 TL9314
C1402
TL2702 TL9322 TL9318
TL9336 TL9332 TL9326
R1420
R9306
R9010
TL2704
R1412
R1413
R9302
TL9331 TL9327 TL9323 TL9317 TL9313
R1419
R1417
TL9335 TL9311
TL9359 TL9329 TL9325 TL9321 TL9319 TL9315
R2708 TL9333 TL9355 R9011 11
TL9375 TL9382 TL9380 TL9379 TL9381 TL2215 TL2213 TL1120 TL1116 TL1114 TL1111 TL1108 TL1102
C2723
C2703 TL2217 TL2201
R2726
TL2703
TL9301
R2731
Q2704 TL9302
C2724
TL9384 TL9310 TL9383 TL9378 TL9352 TL1121 TL1119 TL1117 TL1115 TL1112 TL1110 TL1107
R2744 FB2701 TL2218 TL2216 TL2214 TL2212
Q2204
TL9353
A
R2725 TL2210
R2742 R2741
R2730
TL2211
R2752
TL2219
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
9–6
LC-37D44U
CHAPTER 10. SCHEMATIC DIAGRAM
LC-37D44U
Service Manual
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
10 – 1
LC-37D44U
[2] R/C, LED Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 2
LC-37D44U
[3] KEY Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 3
LC-37D44U
[4] MAIN Unit
• MAIN Unit-1/20
B
œʼnĮŊřńĴĶĹŘŋŒśŔ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 4
LC-37D44U
• MAIN Unit-2/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 5
LC-37D44U
• MAIN Unit-3/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 6
LC-37D44U
• MAIN Unit-4/20
œʼnĮŊřńĴĶķŘŋŒśŔ
œʼnĮŊřńĴĶĸŘŋŒśŔ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 7
LC-37D44U
• MAIN Unit-5/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 8
LC-37D44U
• MAIN Unit-6/20
œʼnĮŊřńĴĴIJŘŋŏijŒ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 9
LC-37D44U
• MAIN Unit-7/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 10
LC-37D44U
• MAIN Unit-8/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 11
LC-37D44U
• MAIN Unit-9/20
H œʼnĮŊřńĴĶĺŘŋŒśŒ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 12
LC-37D44U
• MAIN Unit-10/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 13
LC-37D44U
• MAIN Unit-11/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 14
LC-37D44U
• MAIN Unit-12/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 15
LC-37D44U
• MAIN Unit-13/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 16
LC-37D44U
• MAIN Unit-14/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 17
LC-37D44U
• MAIN Unit-15/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 18
LC-37D44U
• MAIN Unit-16/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 19
LC-37D44U
• MAIN Unit-17/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 20
LC-37D44U
• MAIN Unit-18/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 21
LC-37D44U
• MAIN Unit-19/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 22
LC-37D44U
• MAIN Unit-20/20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
10 – 23
PartsGuide
LC-37D44U
PARTS GUIDE
No. S18D7LC37D44U
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
MODEL LC-37D44U
CONTENTS
[1] PRINTED WIRING BOARD ASSEMBLIES [7] CABINET AND MECHANICAL PARTS
[2] LCD PANEL (NOTE: THE PARTS HERE [8] SUPPLIED ACCESSORIES
SHOWN ARE SUPPLIED AS AN ASSEMBLY
BUT NOT INDEPENDENTLY.) [9] PACKING PARTS (NOT REPLACEMENT ITEM)
[3] DUNTKE264FM02 (R/C, LED Unit) [10] SERVICE JIG (USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
3
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
4
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
5
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
6
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
7
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
8
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
10
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
11
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
12
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
13
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
14
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
15
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
16
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
17
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
18
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
19
LC-37D44U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
20
LC-37D44U
[6] NOTE (Conductive cloth tape/Gasket)
Added parts
Conductive Cloth Tape
˴Parts code: ԘPSLDMB359WJZZ Q'ty 1 ԙPSLDMB360WJZZ Q'ty 1
ԚPSLDMB276WJKZ Q'ty 1 ԛPSLDMB375WJKZ Q'ty 1
ԜQEARZA123WJZZ Q'ty 1 ԝPSLDMB361WJZZ Q'ty 2
ԞPSLDMB362WJZZ Q'ty 2
Gasket
˴Parts code: ԟPMLT-A533WJZZ Q'ty 1 ԠPMLT-A534WJZZ Q'ty 1
Bond
˴Parts code: ԡZSLCN-098P2KE (One 150g tube)
Apply bond to
1 location.
10 Apply bond to
1 10 1 location.
10
Apply bond to RA wire 2
1 location.
3
Apply bond to
10 1 location.
10
5 4 Apply bond to
2 locations.
SP wire
Main Shield
9
8
6
7
Attention
When peeling off the conductive cloth tape/gasket for repair, please use the NEW conductive cloth tape/gasket. (When using
the conductive cloth tape/gasket again, keep in mind the decrease in the adhesive power of the conductive cloth tape/gasket.
The purpose of using the NEW conductive cloth tape/gasket is to prevent the conductive cloth tape/gasket from peeling off.)
21
LC-37D44U
[7] CABINET AND MECHANICAL PARTS
7 45
35
1-5 1
30 36
KEY Unit
37
36
1-5
37
1-1 INVERTER Unit
1-5
32
1-5 31
1-5 38
1-7 1-8 1-5 50
1-6
38
1-4
R/C, LED Unit 49
39
1-3
6
1-2 1-6 42
2-2
27 41
34 13 2
51 45
20
45
52
40 42
26 2-1 5
33 53 21 45
9 48
44
17
POWER Unit
12 45 46 25
45 46
29
22 15
14 54 23
28 54 47
43 45 12 21
17 47-2 47-3
14 24
14
10 19
MAIN Unit 53
18
43
11 45
45
4
47-1
45
47-3
45
8
11 43 10 45
16
43
16
16
22
LC-37D44U
23
LC-37D44U
[8] SUPPLIED ACCESSORIES
X1 Cable Clamp X2 AC Cord X3 Remote Control Unit Operation Manual
X6
X7
X8
24
LC-37D44U
[9] PACKING PARTS (NOT REPLACEMENT ITEM)
S8
S9
S7
S7
S4
S5
S6
S10
S2
S3
S7
S7 S11
S1
25
LC-37D44U
26
LC-37D44U
MEMO
SHARP CORPORATION
AV Systems Group
Mar. 2008 CS Promotion Center
TQ2480-S MI. KD Yaita, Tochigi 329-2193, Japan