Você está na página 1de 20

1 Which statement is true about the reverse lookup DNS zone?

It is most commonly experienced when users are surfing the Internet.

It is the backup for the forward lookup zone.

It dynamically updates the resource records.

It resolves an IP address to a fully qualified domain name.

2 What is the purpose of using the copy tftp flash command on a router?
to back up the current IOS image to a server

to restore the IOS image from a server

to back up the router configuration to a server

to restore the router configuration from flash

3 To manage a Cisco switch using Telnet, where would the management IP address be configured on the
switch?
VLAN 1 interface

first vty port

first trunk port

console port

FastEthernet 0/1 interface

Refer to the exhibit. Which two statements describe the data conversation shown? (Choose two.)
The data conversation was started by the HTTP application process running on the client.

The data conversation is identified by TCP port 80 on the client.


The user started the data conversation by sending an e-mail.

The IP address of the Internet server is 192.168.17.43.

The Internet server will send data to port 8547 on the client.

Refer to the exhibit. Host A is unable to ping host B. What can be done to solve this problem? (Choose two.)
Configure a default route on R1 with the use of exit interface Fa0/0.

Configure a default route on R2 by using the exit interface Fa0/0.

Configure a static route on R1 with 192.168.0.1/24 as the next hop address.

Configure a static route for network 10.1.2.0/24 on R2 and use exit interface S0/0/0.

Configure a static route for network 10.1.1.0/24 on R1 with the next hop address as the IP address of
the serial interface of R2.
6 Which type of address is 192.168.17.111/28?
host address

network address

broadcast address

multicast address
7

Refer to the exhibit. R1 and R2 are configured with the IP addresses as displayed. They are also properly
configured with static routes to the remote networks. The network administrator runs the show ip route
command on both routers and shows the displayed results.

Why do the static routes fail to appear in the routing table?


The default route has not been configured on the routers.

A dynamic routing protocol has not been configured.

The router interfaces are administratively down.

The serial interfaces must be configured with an address in the 10.14.14.0 network.

8
The show ip route command was executed on one of the routers shown in the graphic and the following
output was displayed:

C 192.168.4.0/24 is directly connected, Serial0/0


R 192.168.5.0/24 [120/1] via 192.168.4.2, 00:00:19, Serial0/0
R 192.168.1.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
R 192.168.2.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
C 192.168.3.0/24 is directly connected, Serial0/1

From which router was this command executed?


A

Refer to the exhibit. A network technician issues the tracert 192.168.2.99 command successfully on host A.
What are two consequences of running this command? (Choose two.)
The traceroute packet is broadcast to the network.

The command output will display the IP address of both the inbound and outbound router interfaces
that the packet passes through.
The command output will display all routers through which the packet has passed.

All successful hops between host A and host B will reply to the echo request with a proxy ICMP
response.
The command will calculate the time between when the packet is sent and when a reply is received
from a router.

10

Refer to the exhibit. Which subnet mask would accommodate the number of hosts indicated for all subnets
if the major network address was 192.168.25.0/24?
255.255.0.0

255.255.224.0

255.255.255.0

255.255.255.224

255.255.255.240

255.255.255.248
11 Which routing protocol facilitates the exchange of routing information between different autonomous
systems?
OSPF

EIGRP

RIP

BGP

12 How do port filtering and access lists help provide network security?
They prevent specified types of traffic from reaching specified network destinations.

They alert network administrators to various type of denial of service attacks as they occur.

They prevent viruses, worms, and Trojans from infecting host computers and servers.
They enable encryption and authentication of confidential data communications.

13 A customer reports connectivity problems to an ISP technician. Upon questioning the customer, the
technician discovers that all network applications are functioning except for FTP. What should the technician
suspect is the problem?
misconfigured firewall

bad port on switch or hub

misconfigured IP addressing on the customer's workstation

wrong DNS server configured on the customer's workstation

wrong default gateway configured on the customer's workstation

14

Refer to the exhibit. While configuring the serial interface of a router, the network administrator sees the
highlighted error message. What is the reason for this?
The serial interface is administratively down.

The serial interface is already configured with an IP address.

The network administrator has attempted to configure the serial interface with a broadcast
address.

The same IP address has been configured on another interface.

15 Which statement correctly describes the importance of an SLA?


It outlines the range of services received by the ISP.

It outlines the process to resolve planned incidents.

It outlines the management, monitoring, and maintenance of a network.

It outlines the termination costs according to the budget cycle of the customer.
16 What is a characteristic of the EIGRP routing protocol?
It has a hop count limitation that makes it suitable only for small, simple networks that consist of fewer
than 15 hops.

It does not include subnet mask information in routing updates.

It builds the topology table based on all of the advertisements from its neighbors.

It maintains a full database of distant routers and the methods by which they interconnect.
17

Refer to the exhibit. R1 and R2 are configured with the commands that are displayed. All interfaces are
properly configured, but neither router is receiving routing updates. What two things can be done to solve
the problem? (Choose two.)
Configure the routing protocol on R1 for network 10.0.0.0.

Configure the routing protocol on R2 for network 10.0.0.0.

Configure the routing protocol on R1 for network 192.168.4.0.

Configure the routing protocol on R1 for network 192.168.2.0.

Configure the routing protocol on R2 for network 192.168.1.0.

Configure the routing protocol on R2 for network 192.168.3.0.

18 Which statement is correct about the proxy support that is offered by the HTTP protocol?
It allows clients to make direct network connections to other network services.

It filters unsuitable web content.

It reduces the speed of the network.

It encrypts the data that is being transmitted.

19 What are two reasons for issuing the show ip route command on a router? (Choose two.)
It displays the routing activity in real time.

It displays the length of time until the next routing update.

It displays the directly connected networks.

It displays all of the routing protocols that are configured on the neighboring routers.

It displays the routing protocol that is receiving updates from the neighboring routers.
20

Refer to the exhibit. Host A is unable to ping R1. Which two configuration steps should be performed on R1
to solve this problem? (Choose two.)
Configure the appropriate line password to access the router.

Configure the speed of the interface.

Enable the interface administratively.

Configure a dynamic routing protocol on the router.

Configure the subnet mask on the router correctly.


21 What is a characteristic of UDP?
It is a reliable transport protocol.

It requires the source host to resend packets that are not acknowledged.

It adds a minimal amount of overhead to the data to be transmitted.

It is a connection-oriented protocol.

22 Which cable type is used to interconnect the FastEthernet interfaces of two routers?
straight-through

crossover

console

rollover

23 What routing protocol would be appropriate to use for exchanging routes between ISPs?
RIPv2

BGP
OSPF

EIGRP

24

Refer to the exhibit. Which cable path segments require the use of crossover cables?
A, D, F

B, C, E

B, D, E

A, C, F

25 Which statement correctly describes the function of AAA?


It prevents unauthorized access to a network.

It filters traffic based on destination IP and port number.

It enables users to send information to a daemon that is running on a management station.

It encrypts data to provide network security.

26 When a router learns two paths to the same destination network, which two factors determine the path that
will be included in the routing table? (Choose two.)
route metric

the MAC address of the neighboring router

the source IP address in data packets

the IP address of the next hop router

administrative distance
27 A hacker attempts to reach confidential information that is stored on a server inside the corporate network.
A network security solution inspects the entire packet, determines that it is a threat, and blocks the packet
from entering the inside network. Which security measure protected the network?
an IDS

an IPS

a host-based firewall

Anti-X software

28

Refer to the exhibit. What is used to exchange routing information between routers within each AS?
static routing

IGP routing protocols

EGP routing protocols

default routing

29
Refer to the exhibit. What fact can be determined from the exhibited output?
PPP is enabled on this router.

The bandwidth setting of the interfaces is consistent with a T1 connection.

The serial0/0/0 interface is administratively down.

The default encapsulation is set for the serial0/0/0 interface.

Subnet mask 255.255.255.255 has been configured for the serial0/0/0 interface.

30 Which combination of network address and subnet mask allows 62 hosts to be connected in a single
subnet?
Network address 10.1.1.4 Subnet mask 255.255.255.240

Network address 10.1.1.0 Subnet mask 255.255.255.252

Network address 10.1.1.0 Subnet mask 255.255.255.192

Network address 10.1.1.4 Subnet mask 255.255.255.248

31

Refer to the exhibit. What two addresses are the broadcast addresses for network A and network B?
(Choose two.)
Network A broadcast address 192.168.1.32

Network A broadcast address 192.168.1.47

Network A broadcast address 192.168.1.15

Network B broadcast address 192.168.1.207

Network B broadcast address 192.168.1.240

Network B broadcast address 192.168.1.192

32

Refer to the exhibit. Devices need to connect to the file server from remote networks. What method should
be used to provide the file server with an IP address to allow these connections?
static NAT

static PAT

dynamic NAT

dynamic PAT

33
Refer to the exhibit. The network administrator uses the exhibited commands to configure R1 and R2. The
administrator confirms Layer 1 connectivity between the two routers is functioning properly. However, R1 is
unable to ping the serial interface of R2.

What could be the reason for this problem?


The subnet mask is incorrectly configured on both routers.

A static route is not configured on both routers.

Different encapsulations are configured on the two routers.

The clock rate is not set on any of the router serial interfaces.

34 In order to load an initial configuration on a new switch, a network administrator has connected a laptop to
the switch via the use of a console cable. About a minute after the network administrator powers on the
switch, the SYST LED on the front of the switch changes from blinking green to amber. What does this
indicate?
The network administrator has made an improper physical connection to the switch.

The switch is ready to have a configuration file loaded.

A port on the switch is bad.

The switch failed POST.

35

Refer to the exhibit. Router R1 has been configured with the commands that are displayed. Which password
will be used to access the EXEC privileged mode of the router?
password1

password2

password3

password4
36 A user is unable to connect to the Internet. The network administrator decides to use the top-down
troubleshooting approach. Which action should the administrator perform first?
Run the tracert command to identify the faulty device.

Check the patch cable connection from the PC to the wall.

Enter an IP address in the address bar of the web browser to determine if DNS has failed.

Run the ipconfig command to verify the IP address, subnet mask, and gateway on the PC.

37

Refer to the exhibit. There is no routing protocol configured on either router. Which command will create a
default route on R1 to forward the traffic to R2?
R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

R1(config)# ip route 0.0.0.0 0.0.0.0 192.168.0.2

R1(config)# ip route 0.0.0.0 0.0.0.0 192.168.0.1

R1(config)# ip route 0.0.0.0 0.0.0.0 S0/0/1

38 What occurs during a static NAT translation?


Multiple local addresses are mapped to one global address.

The host device is configured with a permanent outside global address.


A one-to-one mapping is created between an inside local and outside global address.

The router is forced to return the inside global address to the address pool when a session ends.

39

Refer to the exhibit. R2 is connected to the Serial0/0/1 interface of R1 and is properly configured to share
routing updates with R1. Which network will R2 exclude from installing in its routing table?
R 192.168.10.0/24 [120/2] via 192.168.1.2, 00:00:10, Serial0/0/1

R 192.168.7.0/24 [120/1] via 192.168.1.2, 00:00:10, Serial0/0/1

R 192.168.6.0/24 [120/15] via 192.168.3.2, 00:00:10, Serial0/0/0

R 192.168.8.0/24 [120/2] via 192.168.3.2, 00:00:10, Serial0/0/0

40

Refer to the exhibit. The network administrator uses the command below to configure a default route on
RTB:

RTB(config)# ip route 0.0.0.0 0.0.0.0 fa0/0

A ping issued from PC3 is successful to RTB. However, echo request packets arrive at PC1 but the echo
replies do not make it back to PC3. What will fix this problem?
RTA must be configured to forward packets to the 192.168.2.0 network.

The ip route command needs to be edited so that the next hop address is 10.1.1.5.

The ip route command needs to be edited so that the 192.168.2.1 address is the next hop address.

The ip route command should be removed from the RTB router configuration.
Another default route should be configured on RTA with a next hop address of 10.1.1.6.
41 A host has been properly cabled and configured with a unique hostname and valid IP address. Which two
additional components should be configured to enable the host to access remote resources? (Choose two.)
the subnet mask

the MAC address

the default gateway

the loopback IP address

the DHCP server IP address

42 An organization has 50 traveling salespersons who must be able to connect to the company network from
client sites and hotels. Which WAN connection will allow this access?
Frame Relay

Cable

DSL

dialup

43 A network administrator has designed a Class B network with a 255.255.254.0 mask. Which two statements
are true for this network? (Choose two.)
There are 128 subnets.

There are 256 subnets.

There are 512 subnets.

There are 126 usable hosts per subnet.

There are 254 usable hosts per subnet.

There are 510 usable hosts per subnet.

44 Which routes are automatically added to the routing table on a neighbor router when routing protocols
exchange information about directly connected networks?
dynamic routes

static routes

default routes

directly connected routes

45 Which two statements are correct about the ICMP packet that is used by the ping command? (Choose two.)
It guarantees datagram delivery.

It verifies Layer 3 connectivity.

It acknowledges the receipt of TCP segments.

It determines where a packet is lost on the path from the source to the destination.

It measures the time that elapses between when the request packet is sent and the response packet is
received.
46 What is the effect of issuing the banner login #Unauthorized login prohibited# command on a router?
It will display the message "Unauthorized login prohibited" before the router prompts for a user name.

It replaces the banner motd command.

It causes the router to prompt for login credentials for any user who is attempting to connect to the
router.
It causes the message "Unauthorized access prohibited" to display when a HyperTerminal connection is
idle.

47 Which two statements are correct about the DNS hierarchy? (Choose two.)
The root server maintains records for all servers in the Internet.

DNS relies on a hierarchy of decentralized servers to maintain records.

The root servers maintain records about how to reach top-level domain servers.

All DNS servers manage databases that store name-to-IP mappings for the entire DNS structure.

A query requesting a name resolution starts from the client and is passed directly to the server at the
top of the DNS hierarchy.

48 Which statement is correct about passive data connections in the FTP protocol?
The server initiates the data transfer connection.

The server forwards its IP address and a random port number to the FTP client through the control
stream.

The firewalls do not permit passive data connections to hosts that are located within the network.

The client forwards data to port 21 of the server.

49 A new Cisco IOS is installed on a router in the default location. After booting, the router enters ROMMON
mode. What is the reason for this?
The configuration is missing in NVRAM.

The configuration register value is set to 0x2102.

There is inadequate memory to load the Cisco IOS.

The boot system command has not been run.


50 Which type of WAN connection uses a circuit-switched network?
ISDN

Frame Relay

DSL

Cable
51 How does an SNMP trap aid network monitoring and management?
It reports to the management station by responding to polls.

It collects information for the management station by using polling devices.

It sends an alert message to the management station when a threshold is reached.

It flags attempts to begin a DoS attack on the network.

52 A network is spread across two buildings that are separated by a distance of 500 feet (152 meters). An
electrical transformer is installed near the cable route. Which type of cable should be used in this network?
STP

UTP

coaxial

fiber-optic

53 Which two statements are correct about the UDP protocol? (Choose two.)
It utilizes a flow control mechanism.

It uses windowing.

It does not provide acknowledgment of receipt of data.

It is a connectionless protocol.

It guarantees the sequential arrival of data packets.

54 Which statement describes a route that has been learned dynamically?


It is automatically updated and maintained by routing protocols.

It is unaffected by changes in the topology of the network.

It has an administrative distance of 1.

It is identified by the prefix C in the routing table.


55

Refer to the exhibit. Which statement is true based on the exhibited information?
The router is using a link-state routing protocol.

The router will get routing updates on the FastEthernet0/0 interface.

The router will not forward routing updates from the Serial0/0/0 interface.

The network for Fa0/1 will be included in the routing updates that are sent from this router.
56 What can cause a problem at the data link layer?
a faulty network cable

a firewall that is blocking all HTTP traffic

incorrectly configured device drivers

incorrectly configured subnet masks

57 A user is able to ping IP addresses but is unable to ping hosts by domain name. What should be checked at
the workstation of the user?
the device driver configuration of NIC

the LED status of the NIC

the DNS configuration

the firewall settings

58 Different hosts connect to the same switch port at different times. If the switch port is configured with
dynamic port security, how does it process the MAC addresses?
The addresses are manually assigned with the use of the switchport command.

The addresses are dynamically learned and stored in the address table.

The addresses are dynamically configured and saved in the running configuration.

The addresses are stored in the address table and added to the running configuration.

Você também pode gostar