Escolar Documentos
Profissional Documentos
Cultura Documentos
SECTION 1.GENERAL
SERVICING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 ESD PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
SECTION 3. EXPLODED VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 SECTION 4. SPEAKER PART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 SECTION 5. REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
- 1-1 -
SECTION 1. GENERAL
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use. 2) The pick-up should never be subjected to external pressure or impact.
Drop impact
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials. 2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or damage to the printed-circuit board. 3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason the adjustment point and installation screws should absolutely never be touched. 4) Laser beams may damage the eyes! Absolutely never permit laser beams to enter the eyes! Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
NEVER look directly at the laser beam, and dont let contact fingers or other exposed skin.
5) Cleaning the lens surface If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cotton swab should be used, taking care not to distort this.
Pressure Magnet
Pressure
Conductive Sheet
6) Never attempt to disassemble the pick-up. Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab. (Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
- 1-2 -
CLEARING MALFUNCTION You can reset your unit to initial status if malfunction occur(button malfunction, display, etc.). Using a pointed good conductor(such as driver), simply short the RESET jump wire on the inside of the volume knob for more than 3 seconds. If you reset your unit, you must reenter all its settings(stations, clock, timer) NOTE: 1. To operate the RESET jump wire, pull the volume rotary knob and release it. 2. If you wish to operate the RESET jump wire, it is necessary to unplug the power cord.
VOLUME UP RESET jump wire
VOLUME KNOB
DOWN
- 1-3 -
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESD devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices. 6. Do not remove a replacement ESD device from its protective package until immediately before you are ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials). 7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will by installed. CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER SAFETY PRECAUTIONS. 8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device).
- 1-4 -
SECTION 2. ELECTRICAL
TROUBLESHOOTING GUIDE
I CD PART
TURN ON CD
YES NO
OPEN CLOSE CHECK CONNECTOR CHECK ( PN808,PN807 )
YES
CHECK POWER SUPPLY CIRCUIT( PN808 )
NO
CONNECTOR CHECK ( PN808,PN807,PN802,PN801 )
YES
CHECK MICOM INTERFACE CIRCUIT( PN807 )
NO
READING OK CHECK
CONNECTOR CHECK(PN801,PN802)
YES
NO
CONNECTOR CHECK (PN808)
YES
OK
- 2-1 -
OPEN CLOSE NG
CONNECTOR LOCKING CHECK ( PN808,PN807 )
YES
CHECK POWER SUPPLY CIRCUIT( PN808 ,PN807) PN808 PIN 5 = 6.2V, PIN 7 = 5V PN807 PIN 1 = 5V
NO
YES NO
CHECK VOLTAGE CHANGE OF OPEN CLOSE , AND BTLMUTE VOLTAGE(= 5V) (PN807 PIN 20:OPEN, 19:CLOSE, 4:BTLMUTE) DEFECTIVE MICOM
YES
CHECK VOLTAGE CHANGE LO+, LO- OF IC803 (PN807, PIN OPEN:20, CLOSE:19)
NO
DEFECTIVE IC803
NO
DEFECTIVE MECHANISM
- 2-2 -
YES
CHECK POWER SUPPLY PORT( PN808 ,PN807) PN808 PIN 5 = 6.2V, PIN 7 = 5V PN807 PIN 1 = 5V
NO
DEFECTIVE CONNECTOR OR MAIN POWER SUPPLAY
YES
NO
DEFECTIVE IC805
YES
NO
DEFECTIVE MICOM OR CONNECTOR
YES
CHECK MICOM INTERFACE CIRCUIT( PN807 ) PN807 PIN 11,13,14,15 SIGNAL CHECK (11: STAT, 13: MDATA, 14:MCLK, 15:MLD) CHECK THE WAVE FORM #1
NO
DEFECTIVE MICOM OR CONNECTOR
YES NO
DEFECTIVE IC801
- 2-3 -
YES NO
DOES SLED MOVE ?
A
YES
CHECK PN802 PIN 3,4( SL+,SL-) DEFECTIVE PICKUP OR IC803 OR IC801 OR IC802
NO
B
YES
CHECK PN801 PIN 13,16 ( FA-, FA+) DEFECTIVE PICKUP OR IC803 OR IC801
NO
C
YES
CHECK PN802 PIN 10( LD ) DEFECTIVE PICKUP OR IC802
NO
DOES SPINDLE ROTATE ?
D
CHECK PN802 PIN 5,6( SP+,SP-) DEFECTIVE PICKUP OR IC803
YES
IS READING OK ?
NO
E
CHECK PN801 PIN 14,15 (TA- ,TA+) DEFECTIVE PICKUP OR IC803 OR IC801 OR IC802
- 2-4 -
DOES SL+ WAVEFORM APPEAR AT ( IC803 PIN14 AND PN802 PIN3) WAVEFORM #2 SLED MOTOR WAVE
NO
DOES SLIN WAVEFORM APPEAR AT ( IC803 PIN 5) WAVEFORM #2 SLED DRIVE WAVE
NO
DEFECTIVE IC801
YES NO
DEFECTIVE IC803
NO
CHECK PN802 CONNECTOR LINE
YES NO
DEFECTIVE PICKUP SLED MOTOR
- 2-5 -
DOES FA+ WAVEFORM APPEAR AT ( IC803 PIN15 AND PN801 PIN16) WAVEFORM #3 FOCUS COIL DRIVE WAVE
NO
DOES FAIN- WAVEFORM APPEAR AT ( IC803 PIN 26) WAVEFORM #3 FOCUS DRIVE WAVE
NO
DEFECTIVE IC801
YES NO
DEFECTIVE IC803
NO
CHECK PN801 CONNECTOR LINE DEFECTIVE PN801 CONNECTOR
YES NO
DEFECTIVE PICKUP FOCUS ACTUATOR
- 2-6 -
C
IS ?V APPLIED TO PIN10 OF PN801 LASER SUPPLY VOLTAGE CHECK
NO
NO
DEFECTIVE IC805
YES
NO
DEFECTIVE IC802
NO
NO
YES NO
DEFECTIVE PICKUP LASER PART
- 2-7 -
DOES SP+ WAVEFORM APPEAR AT ( IC803 PIN12 AND PN802 PIN6)WAVEFORM #4 SPINDLE MOTOR DRIVE WAVE
NO
DOES SPIN WAVEFORM APPEAR AT( IC803 PIN 6) WAVEFORM #4 SPINDLE DRIVE WAVE
NO
DEFECTIVE IC801
YES
DEFECTIVE IC803
NO
NO YES
DEFECTIVE PICKUP SPINDLE MOTOR
- 2-8 -
DOES TA+ WAVEFORM APPEAR AT ( IC803 PIN17 AND PN801 PIN15) WAVEFORM #5 TRACKING COIL DRIVE WAVE
NO
DOES TAIN- WAVEFORM APPEAR AT ( IC803 PIN 23) WAVEFORM #5 TRACKING DRIVE WAVE
NO
DEFECTIVE IC801
YES NO
DEFECTIVE IC803
NO
YES
DOES ARF SIGNAL APPEAR? (IC802 PORT 8) WAVEFORM #6
NO
YES
DOES FE, TE SIGNAL APPEAR? (IC802 PORT FE:23, TE:21) WAVEFORM #6
NO
NO
DEFECTIVE IC801
- 2-9 -
I AUDIO PART
P-SENS PART CHECK ZD 701(+) Voltage check Half-wave rectification wave form check IC301 26PIN PATTERN Check R746 check, then ZD701 replacement D713 Replacement
VKK CHECK CN305 4pin DC -33V check ZD 700 -33V check IC301 51PIN check ZD 754 turn on check ZD700 replacement
C763 -33V and less check D707, D708 replacement Q754 replacement normal Refer to power supply check
- 2-10 -
POWER CHECK Every kinds of Fuse check Fuse replace C720(+), C770(-) DC power output check CN704 1, 2, 3, 4, 5, 6, 7, 9, 10 AC voltage output check Power supply Assy check and transformer replacent C725(+), C729(-) DC power output check D713(PBU604) check CN704, 11, 12 pin AC power output check IC704, IC705, IC705 power output check Power supply Assy check and transformer replacent IC704, IC705 , IC710 check and replacement IC704, IC705, IC710 power output check (12V) IC301 78PIN 5V check IC709 DC5V check IC709 replacement CN513 7PIN 5V check (at CD Function) Q904(A1273) Base Low check normal operation Check IC501(BU2090) 14PIN HIGH check IC5019BU2090 check & replace Check and replace defective Q904, CD Assy check replacement IC301 5V Power output PN304/CN304 15 PIN check
- 2-11 -
Muting circuit Troubleshooting (if MUTE) Q752(A102) Base LOW c-COM operation status check c-COM 2PIN(A-MUTE) LINE check Q702(A102) operation status check C720(+), C770(-) DC power output check Q702(A102) Replace if defective
MUTE
No sound Input check (AUX29,36 TUNER30,35 TAPE28/37 CD31/34 PIN) Check each function input and operation status check IC 601 24/25 PIN Output check Refer to IC601(TDA7429D) IC specification IC601 input check (22/21PIN) c-COM check (and CLK/DATA check) IC601 output check (14PIN) IC601 39PIN (over 8V) check and power supply circuit check normal IC705 7812 operation status check (DC12V) PN701/CN701 connection status check ZD601 9.1V check
- 2-12 -
Specific FUNCTION MODE has no sound (TDA7468D) TAPE Refer to IC202 Troubleshooting
IC202 input check (HEAD input) "A"DECK 1,24 "B"DECK 23,2 DECK HEAD WIRE connection status check IC202 output check (5,20 PIN) IC501 10 PIN(PB MUTE) operation status check IC601 36,29 PIN signal input check
AUX
CD
TUNER
Refer to TUNERMODULE
- 2-13 -
MIC
IC301 Troubleshooting C301 17, 46, 72, 90 power applied check Refer to power supply check IC301 15PIN 5V applied check P-SENS terminal check X301 oscilates or not X301 replace When IC301 11Pin voltage input. HighLowHigh RESET circuit check IC301 replace
- 2-14 -
IC501,502,302(BU2029) Troubleshooting IC501 16PIN power applied check Refer to power supply check IC501 2, 3 PIN CLK Data check IC301 3,4 PIN data check (When switched to CD, TAPE Function) CONTROL function check IC501 replace normal Refer to IC301 Troubleshooting Pattern check between IC301 and IC501
IC601(TDA7468D) Troubleshooting IC601 1PIN power applied check Refer to power supply check IC601 21,22 Pulse waveform check (with tunning VOL DIAL) IC301 10,8Pin check IC601 35,30 Pin waveform output check IC601 replace IC601 36,29Pin waveform input check MICOM(10,8) - IC601(21,22) Pattern check IC301 Troubleshooting
- 2-15 -
IC701(AMP MODULE) Troubleshooting AMP ON/OFF check IC502 6PIN operation status check
-9V(IC706) +9(IC710) operation status check (9,14PIN check) -9V(IC706) +9(IC710) replace if defective Refer to Muting circuit
18,5Pin(-), 20, 3Pin(+) Power check Refer to power supply check 6,17 Pin signal output check RELAY operation status check (RY703,701) OK
IC701(AMP MODULE) Troubleshooting AMP ON/OFF check IC502 6PIN operation status check -9V(IC706) +9(IC710) operation status check (11,7 PIN check) -9V(IC706) +9(IC710) replace if defective 9Pin signal input check Refer to Muting circuit 12Pin(-), 15Pin(+) voltage check Refer to power supply check 12 Pin signal output check RELAY operation status check (RY702) OK
- 2-16 -
PLAY check (KIA6289N) IC202 18Pin VCC power applied Refer to power supply check IC202 5,20 Pin signal output check Deck Mecha operation performance check Muting circuit check IC202 replace Deck Mecha replace
Rec check (Q252, Q202 ON : R273, R223 High) IC601 33,32 OUT check Q253, Q203 Base "Low" check IC202 11,14 Pin signal input check Q253,Q203 replace IC202 9,16 Pin output check IC202 18Pin VCC voltage check IC201 6(12V), 4 Pin High check Voltage check, IC203 Troubleshooting check L203 2,3PIN oscilation check C236(+) power supply check Deck replace Q208 Base 0.6V supplied check IC203 Troubleshooting check Q208 Collector Low Q208 replace Q207 replace L203 replace normal Refer to power supply check Refer to IC203 Troubleshooting
- 2-17 -
Q253,203 "ON"//"OFF"
- 2-18 -
- 2-19 -
- 2-20 -
PIN CONFIGURATION
- 2-21 -
AF230W20CM (IC701)
BLOCK DIAGRAM
PIN CONFIGURATION
- 2-22 -
AF310W20CM (IC701)
BLOCK DIAGRAM
PIN CONFIGURATION
PIN DESCRIPTION
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol N_DO VSS N_CS P_CS AM_F2 AM_F1 VEE STANDBY IN P_STATE VCC OUT GND SUBGND VDD P_DO Type O G P P O G I I P I I O I P I O Description NMOS Drain Output Negative supply Voltage NMOS Current Sense Input PMOS Current Sense Input AM Mode control Input 2 AM Mode control Input 1 Negative supply Voltage ON/OFF control Audio Input Protection State Positive supply Voltage Audio Output Signal Ground Sub Ground Positive supply Voltage PMOS Drain Output
- 2-23 -
PIN DESCRIPTION
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Symbol L_DO SUBGND VDD_L L_GND VSS_L L_OUT AM_F1 L_CS VCC L_IN STANDBY P_STATE R_IN VEE R_CS AM_F2 R_OUT VSS_R R_GND VDD_R SUBGND R_DO Type O G P P O G I I P I I O I P I I G O P P G O Description L-Channel Drain Output Sub Ground L-Channel Positive supply Voltage L-Channel Signal Ground L-Channel Negative supply Voltage L-Channel Audio Output AM Mode control Input 1 L-Channel Current Sense Input Positive supply Voltage L-Channel Audio Input ON/OFF control Protection State R-Channel Audio Input Negative supply Voltage R-Channel Current Sense Input AM Mode control Input 2 R-Channel Audio Output R-Channel Negative supply Voltage R-Channel Signal Ground R-Channel Positive supply Voltage Sub Ground R-Channel Drain Output
TC4052BP (IC801)
BLOCK DIAGRAM
PIN ASSIGNMENT
- 2-24 -
BLOCK DIAGRAM
2-25
2-26
SCHEMATIC DIAGRAM
MAIN SCHEMATIC DIAGRAM
2-27
2-28
2-29
2-30
2-31
2-32
2-33
2-34
2-35
2-36
2-37
2-38
WIRING DIAGRAMS
2-39
2-40
2-41
2-42
2-43
2-44
2-45
2-46
2-47
2-48
2-49
2-50
2-51
2-52
2-53
2-54
2-55
2-56
2-57
2-58
450
302
290
286
262
276
272 451
284 A48
267
261 258
452
268 277 260 A49 256 257 254 255 263 273 264 275
252
283
282
285
265 278
A00
3-1
3-2
003 401
022 023
015
LG PART NO. 6720AG0002C 6768R-PP03A 6768R-GP03B 6768R-SP01F 6768R-MP01C 6768R-SP01A 6768R-SP03A 6768R-AP01A 6768R-GP01H 6768R-AP01C 6768R-GP01J 6768R-SP01P 6768R-BP01C 6768R-LP01C 6768R-VP03A 6768R-GP03A 6768R-JP03B 6768R-SP01D 6768R-DP01A 6768R-RP01A 6768R-MP01A 6768R-EP03C 6768R-CP01B 6768R-CP01D 6768R-WP03A 6768R-WP03B 6768R-WP01D 6768R-WP01E
DESCRIPTION DECK,AUDIO DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS DECK MECHANISM PARTS
SPECIFICATION CWM42FR47 TOKYO PIGEON L-DOUBL 33-160-4309 PIGEON PRESS CASSE 50-222-4578 PIGEON GEAR IDLER 01-082-4598 PIGEON SPRING CWL4 50-219-4014 PIGEON MOLD CWL44 01-081-4601 PIGEON SPRING CWL4 01-082-4686 PIGEON SPRING CRM4 50-268-3016 PIGEON ARM CWL44 50-093-4503 PIGEON GEAR CRL442 50-239-4072 PIGEON ARM CWL44 50-222-4428 PIGEON GEAR CRL442 01-081-4678 PIGEON SPRING CRL4 02-083-4188 PIGEON BELT/FELT C 50-223-4429 PIGEON PULLEY/FLYW 50-093-4748 PIGEON SOLENOID AS 50-093-4810 PIGEON GEAR ASSY C 50-093-31009 PIGEON PULLEY/FLY 01-080-4609 PIGEON SPRING CWL4 50-259-3342 PIGEON LEVER CWL44 22-027-41054 PIGEON ROLLER CWL 50-219-4033 PIGEON MOLD CWL44 T21V0P PIGEON HEAD CWM42FF30 GSE20A2005 PIGEON SCREW CWL44 GSL10A1704 PIGEON SCREW CWL44 GWN19S035040 PIGEON WASHER CRM 03-000-4532 PIGEON WASHER CRM4 GWP21X045020 PIGEON WASHER CWL GWP12X030040S PIGEON WASHER CW
013 015 016 017 018 019 020 021 022 023 025 026
027 028 029 030 401 403 501 502 504 505
3-3
3-4
006 001 007 016 008 002 401 402 017 506 037 019 018
003 402
A01
015 502 507 009 401 501 026 032 038 028 403 504 025 502 022 023
009 401 031 406 011 409 036 013 035 039 029 040
027
028
3-5
3-6
CD MECHANISM
416
151
159
156 422 165 418 419 153 163 162 417 169 166 417 167 168 155 173
170 171
164
416
LOCA.NO. A26 A30 A35 151 153 155 156 159 162 163 164 165 166 167 168 169 170 171 172 173 175 177 184 185 186 187 416 417 418 419 420 421 422
PART NO 4405RBE004C 3041RB0002C 6717RCA001A 3390RB0002A 4470RB0005A 4681RBA001A 6871RF9211A 3390RB0001A 4400SB0001A 4470SB0003A 4470RB0003A 6871RZ7036A 4470RB0006A 4470RB0007A 4470RB0002A 4860SB0001A 3550SB0001A 524-012AAAA 3040RB0005A 4510RB0001A 4680SBP001A 4470RB0001A 4900RB0001A 3040SB0003A 4970RB0001A 4970RB0001B 88H-0004 88H-0002 353-025BAAA 88H-0003 353S353F 6756SBX001A 353-028H
DESCRIPTION MECHANISM ASSEMBLY BASE ASSEMBLY PICK UP ASSY TRAY GEAR MOTOR ASSEMBLY PWB(PCB) ASSEMBLY,FRONT TRAY BELT GEAR GEAR PWB(PCB) ASSEMBLY,OTHERS GEAR GEAR GEAR CLAMP COVER COVER BASE LEVER MOTOR(MECH) GEAR DAMPER BASE SPRING SPRING CD MECHA PARTS CD MECHA PARTS SCREW CD MECHA PARTS SCREW CD MECHANISM PARTS SCREW
SPECIFICATION CDM-H1503 3 CD CHANGER PU(SPRING DAMPER) KSM-213VSCM SONY FRONT LOADING DISC(CDM-H1503) TRAY (CDM-H1503) TRAY (CDM-H1503) 1503 T/D SENSOR LOADING(CDM-H1503) MAIN(CDM-H1303) PULLEY (CDM-H1303) LOADING (CDM-H1503) CDM-H1503 UP/DW/OP/CL PU UP (CDM-H1503) PU DOWN (CDM-H1503) CAM (CDM-H1503) DISC(CDM-H1303) MAGNET(CDM-H1303) CLAMP MAGNET (030X018X5T) MAIN (CDM-H1503) S/W CLOSE OTHER . . . MAIN (CDM-H1503) RUBBER 3CD CHANGER PU(CDM-H1303) COIL 3 CD CHANGER COIL 50 3CD CHANGER 3X12X12FNM 3X9X12FZMY #NAME? 3X12X10FZMY #NAME? SCREW 2.6X10X10XFZMY CDM-H813 #NAME?
3-7
3-8
827 821 (LEFT) 820 (RIGHT) 825 (LEFT) 826 (RIGHT) 827 828 830 831
839
840
836 832 837 (LEFT) 838 (RIGHT) 822 823 833 834
824
LCOA.NO 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 836 837 838 839 840 841 PART NO. 3720RMF095A 3720RMF095B 6400WETK01A 353M050N 353M051S 5208RM0055A 5208RM0055B 353M051P 6400METC01A 4766RM0099A 6400TETA01A 4766RM0100A 4766RM0098A 6871RU0035A 353M025Q 3610RM0005A 4760RM0077A 4760RM0077B 3091RMW129A 6871RU0012A 1WZZRM0003A DESCRIPTION PANEL,FRONT PANEL,FRONT SPEAKER,WOOFER SCREW,DRAWING SCREW,DRAWING DUCT DUCT SCREW,DRAWING SPEAKER,WOOFER FELT SPEAKER,TWEETER FELT FELT PWB(PCB) ASSEMBLY,SUBSET(AUDIO SCREW,DRAWING FOOT BAFFLE BAFFLE CABINET ASSEMBLY PWB(PCB) ASSEMBLY,SUBSET(AUDIO WASHER,DRAWING SPECIFICATION SPK LMS-W5040 MOLD LEFT LMS-W4 SPK LMS-W5040 MOLD RIGHT LMS-W 20LD5EHC3500O EAW WOOFER 6OHM + 1 D3.5 L14.0 FZMY2 FBK H1 D3.5 L18 SWRCH16A/CR LMS-W5 SPK LMS-W5040 MOLD LMS-W5040/W SPK LMS-W5040/W4040/W3140/W234 + 1 D3.0 L8.0 MSWR3/FZW SILVER 08R60EHC3492D EAW MID-RANGE 12 UNIDENTIFY BLACK 3 INCH WOOFER 05N45EHC3489B EAW TWEETER(CONE LMS-W5040 BLACK 2 INCH TWEETER UNIDENTIFY BLACK 8 INCH WOOFER LMS-W5040 STANDARD 1.0MF POSSI WOOD,3X10 FBK EVA PHI 20 X 2T FE-986/886E ST SPK LMS-W5040 MOLD LEFT LMS-W4 SPK LMS-W5040 MOLD RIGHT LMS-W SPK LMS-W5040 CABINET ASSY PB LMS-W5040 NET WORK ASSY STANDA SPK LMS-W5040 PRESS WASHER 8 X
- 4-1 -
- 4-2 -