Escolar Documentos
Profissional Documentos
Cultura Documentos
GE INDIA INDUSTRIAL PVT LTD, PUNE BILL OF QUANTITIES AS ON 030113 ELECTRICALS WORKS Synefra revised estimate after addendum Sr.No A. ITEMS DESCRIPTION SECTION A-HT. SECTION(CABLES & TERMINATION) HT Cables Supply, taking delivery ,unloading at site,Installation,testing & commissioning of HT XLPE insulated, UE grade, cables, as per IS 7098 , burried in ground such as excavation up to 1 meter depth , backfilling, sand and brick protection and cable tray / tray supports are measured separately and Miscellaneous items such as saddles, 3 mm thick aluminum clamps, cleats, cable tags/ cable markers etc. are included in the scope.(The testing shall including HI-POT test at site before commissioning of the system & Test voltage shall be as per IS 7098) 100 3Cx300 Sq.mm 33kV XLPE-UE- Cable UR 3Cx300 Sq.mm 11kV XLPE -UE-Cable 4972 3Cx240 Sq.mm 11kV XLPE -UE-Cable Note: No straight through joints will be allowded for any single length of cables. CABLE TERMINATIONS : Supply,installation,testing & commisioning of Heat shrikable type cable termination kit with long head Crimping type Lugs, for following XLPE insulated, (UE) grade cable including necessary Right angle /straight insulating boots. The scope also includes thermography test of all terminations at loads by using Themo graphic meter. Indoor type 3Cx300Sq.mm 33kV XLPE-UE- Cable 3Cx300 Sq.mm 11kV XLPE -UE-Cable 3Cx240 Sq.mm 11kV XLPE -UE-Cable Mtr. Mtr. Mtr. 1,896 1,304 1,131 120 120 120 189,618 5,622,469 12,000 596,640 Qty Unit Unit Rate: Rs Supply Installation Amount ( Rs ) Supply Installation
4 UR 38
2.2 Outdoor type 2.2.1 3Cx240 Sq.mm 33kV XLPE-UE- Cable 2.3 Straight Through Joint 2.3.1 3Cx300 Sq.mm 11kV XLPE -UE-Cable 2.3.2 3Cx240 Sq.mm 11kV XLPE -UE-Cable 3 Supply, Installation, Testing and commissioning 33kV Distribution Class Lightening Arrestors with cross arm (1 Set of 3 Nos) Supply installation testing and commissioning of 33kV CT& PT Metering kiosk including approval ,testing from MSEDCL .Detailes of CT & PT shall be as per MSEDCL load sanctionapproval.(Without T.O.D. meter) Supply & installation H.T. Static Three Vector T. O. D. Meter as per MSEDCL.The scope also including calibration & testing of meter from MSEDCL G. I. Pipe-CL -B- 150mm dia.for supporting of HT Cables connected to Overhead Lines ,road crossing etc for MSEDCL incoming cable. HD PVC Pipe 150mm dia.for supporting of HT Cables connected to Overhead Lines ,road crossing etc for MSEDCL incoming cable. TOTAL OF SECTION A- HT SECTION B SECTION -B-HT/LT SUB-STATION EQUIPMENT
No.
27,500
2,100
UR UR 1
No No Set 83,160 3,500 7,500 2,100 210 83,160 343,741 44,100 23,625 3,500 7,500 2,100 3,150 -
No
343,741 -
No
44,100 -
15
Mtr
1,575
UR
Supply, assembly, factory test, loading,Taking delivery at site storing at site & supervision at site of HT panel board indoor type free standing,in various shipping section, Form 4b in construction, IP4X , fabricated out of 3 mm CRCA Sheet etc & as per specifications. Each panel shall comprising as per followings & Enlcosed ELECTRICAL SLD along with Tender Technical Specifciations.The panel shall be suitable for top cable entries for Incoming and outgoing cables except 33 k.V. HT Panels which shall be from bottom. HT Panel Designation:33k.V.Main HT Panel at point of supply:
1.1
Sr.No
ITEMS DESCRIPTION 33-KV-Indoor free Vacuum circuit breaker panels with 1250 Amp Aluminum busbar ,26.2 k.A.-1 Second ,EDO Type for Transformer Feeder with over currents & Auxiliary Protection of Oil Cooled transformer and as per enclosed electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 & as per followings requirements. One (1) No. 33 KV,1250 A VCB/26.2 KA rupturing capacity at 33 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings. Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 30k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT with double wound,100- 225/1+1+1 with metering and protection core. Core 1: 15VA burden for Differential Protection(86) protection ( Class PS)
Qty
Unit
Set
10,395,000
35,000
10,395,000
35,000
a.1
a.2
a.3 a.4
a.4.1
a.4.2 Core 2:15VA burden of metering ( accuracy class 1.0) a.4.3 Core 3: 30VA burden for OC/EF protection ( Class 5P-20)
a.5
Voltage transformer with each , 3 limbs connected in star, dual class , 33kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.)
Protectives Relays as under Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting a.6.1 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) . a.6.1 Stand by Earth Fault relay (51G) a.6.1 Restricated Fault relay (64R) a.6.1 Transformer Auxiliary Protection Relays (63Tx) a.6.1 Trip circuit supervision relay (95). a.6.1 Antipumping relay a.6.1 Lockout relay (86) a.6.1 Under /Over Frequency Relay(81) a.6.1 Under /OverVoltgae Relay(27/59) a.6.1 Reverse Power relay (32) a.6.1 Breaker Failure Relay (52BF) a.7 Control & wiring terminals
a.6
All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. a.7.2 a.8 Test terminal block fuses, circuit lables , phase indication lamps etc. as per Electrical SLD Meterings as under
Voltmeter range 0-33KV with necessary voltmeter selector switch & suitable a.8.1 for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses.
a.8.2
Ammeter range (0-100-225A) with necessary ammeter selector switch dual graduated scale, 96x96 sqmm dial with shrouded terminal . Multifunction Digital meter with RS 485 Serial Communication Port for following parameters.
a.8.3
Sr.No Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,KVA KWH KVAH RKVAH p.f. TDH a.9
ITEMS DESCRIPTION
Qty
Unit
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication circuit breaker ON/OFF/Trip on Fault / Spring charged/Trip circuit healthy/Test/Service positions etc.
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 16 Window Announciator for Transforemr Faults a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 a.10.5 a.10.6 a.10.7 a.10.8 a.10.9 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays NOTE: Above VCB Panel shall be suitable for expandable type for future suit to One incomers & two outgoings feeders. 1.2 HT Panel Designation: 11k.V.Main HT Panel at MRS 11-KV-Indoor Vacuum circuit breaker panels with 1250 Amp, Aluminum busbar 26.2 k.A.-1 Second , EDO Type with over currents ,earth fault Protections. The complete panel shall be as per enclosed electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 with Tender Technical specifications & as per followings requirements. a a.1 EACH INCOMERS 2 Sets of 11 KV,1250 A VCB/26.2 KA rupturing capacity at 11 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings. Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 9k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT with double wound, 350-800Amp/1+1+1 with metering and protection core.
Set
9,544,500
49,000
9,544,500
49,000
a.2
a.3 a.4
a.4.1 Core 1: 15VA burden for Differential (87) protection ( Class PS) a.4.2 Core 2:15VA burden of metering ( accuracy class 1.0) a.4.3 Core 3: 30VA burden for OC/EF protection ( Class 5P-20)
Sr.No
ITEMS DESCRIPTION Voltage transformer with each , 3 limbs connected in star, dual class , 11kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.)
Qty
Unit
a.5
Protectives Relays as under Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting a.6.1 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) . a.6.2 Stand by Earth Fault relay (51G) a.6.3 Restricated Fault relay (64R) a.6.4 Differential Protection relay (87R) a.6.5 Trip circuit supervision relay (95). a.6.6 Antipumping relay a.6.7 Lockout relay (86) a.6.8 Under /OverVoltgae Relay(27/59) a.6.9 Reverse Power relay (32) a.6.10 Breaker Failure Relay (52BF) a.6.11 Master lock out relay (86) Control Wiring & Terminal All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. a.7.2 a.8 Test terminal block fuses, circuit lables , phase indication lamps etc. as per Electrical SLD Meterings a.7
a.6
Voltmeter range 0-12KV with necessary voltmeter selector switch & suitable a.8.1 for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses.
a.8.2
Ammeter range (0-350-800A) with necessary ammeter selector switch dual graduated scale, 96x96 sqmm dial with shrouded terminal .
Mutifunction Digital meter with RS485 Serial Communication Port for a.8.3 following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,KVA KWH KVAH RKVAH p.f. TDH a.9 Other Accessories as under & as per technical specifications
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. / Spring
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 8 Window Announciator for Faults
Sr.No
ITEMS DESCRIPTION
Qty
Unit
a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 a.10.5 a.10.6 a.10.7 a.10.8 a.10.9 b b.1 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays Outgoings VCBs Five (5) Nos. 11 KV, 1250 A VCB/ 26.2 KA rupturing capacity at 11kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the following: Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. Cast Resin CT with double wound, with metering and protection core. CT.Ratio as indciated on Electrical SLD for each outgoing VCB in MRS room panel 15VA burden for protection ( Class 5P-20) 15VA burden of metering ( accuracy class 1.0) b.4 Protection to each outgoings Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
b.2
b.3 / Spring All control wiring necessary for the above including interconnections. The size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per standard practice. b.6 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels -
Trip circuit supervision relay (95). Lockout relay (86) Antipumping relay
b.5
Other Accessories as under & as per technical specifications Necessary DC supply healthy LED type indication lamp & switch. Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement. Danger plate (As per specification) Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. Three pin socket + switch. Anticondensation space heater / thermostat 50x6mm, copper earth bus shall be provided for the full length of panel. Terminal boxes with single gland trifucating cable box suitable for 11KV aluminium XLPE cable of size 3C x 300sqmm for incoming & outgoing &Suitable for TOP CABLE ENTRY
Sr.No
ITEMS DESCRIPTION Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Numerical Relays
Qty
Unit
c c.1
BUS COUPLERS: 2Nos Bus couplers VCB Panel comprising as under As per above Outgoing VCB Breaker panels except No CT for metering & no meters. 3 Nos Bus PT Section: 3Nos Withdrawable type BUS PT section as shown in Tender Electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5Sh No 1 of 03 NOTE: 1: Above Panel shall be suitable for Expandable type from both Side NOTE: 2: Control Voltgae Bus for D.C. & AC votlage shall be as per Electrica SLD ref.GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 NOTE: 3: Interlocks and control logics shall be suitable for 4 Incomers & 3Bus-Couplers as shown in above mentioned SLD
1.3
HT Panel Designation :11kV HT Panel Office Load Centre-1 as 11-KV-Indoor Vacuum circuit breaker panels with 1250 Amp,26.2 k.A.-1 Second , EDO Type with over currents ,earth fault Protections. The complete panel shall be as per enclosed electrical SLD Ref GE-P-FAC-Ele0001-011-155000-R5- Sh No 1 of 03 with Tender Technical specifications & as per followings requirements.
Set
a a.1
2 NOS INCOMER FEEDER :EACH INCOMERS COMPRISING AS UNDER. 11 KV,1250 A,Aluminum Busbar VCB/26.2 KA rupturing capacity at 11 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings. Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 9k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT protection core. with double wound, 250-Amp/1+1 with metering and
a.2
a.3 a.4
a.4.1 Core 1:15VA burden of metering ( accuracy class 1.0) a.4.2 Core 2: 30VA burden for OC/EF protection ( Class 5P-20)
a.5
Voltage transformer with each , 3 limbs connected in star, dual class , 11kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.)
Protectives Relays as under to each Incomers Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting a.6.1 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) . a.6.1 Trip circuit supervision relay (95). a.6.2 Antipumping relay a.6.3 Lockout relay (86) a.6.4 Under /OverVoltgae Relay(27/59) a.6.5 Reverse Power relay (32) a.6.6 Breaker Failure Relay (52BF) a.6.7 Master lock out relay (86)
a.6
Sr.No a.7
ITEMS DESCRIPTION
Qty
Unit
Control Wiring & Terminal All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per a.7.2 Electrical SLD GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03
a.8
Voltmeter range 0-12KV with necessary voltmeter selector switch & suitable a.8.1 for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses.
a.8.2
Mutifunction Digital meter with RS485 Serial Communication Port for following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,k.V.A KWH KVAH RKVAH p.f. TDH
a.9
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. / Spring
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 8 Window Announciator for Faults a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 a.10.5 a.10.6 a.10.7 a.10.8 a.10.9 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays Note: E& M Interlocaks shall be provided as indicted on Tender Electrical SLD for both Incomers Outgoings VCBs One (1) Nos. 11 KV, 1250 A VCB/ 26.2 KA rupturing capacity at 11kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the following: Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. Cast Resin CT with double wound, with metering and protection core. CT.Ratio as indciated on Electrical SLD for each outgoing VCB in MRS room panel 15VA burden for protection ( Class 5P-20)
b b.1
b.2
b.3 -
Sr.No
Qty
Unit
b.4
Protection to each outgoings Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
Trip circuit supervision relay (95). Lockout relay (86) Antipumping relay b.5 Metering : Mutifunction Digital meter with RS485 Serial Communication Port for following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KWH KWH KVAH RKVAH p.f. TDH b.6 Other Accessories as under & as per technical specifications Necessary DC supply healthy LED type indication lamp & switch. Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement. Danger plate (As per specification) Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. Three pin socket + switch. Anticondensation space heater / thermostat 50x6mm, copper earth bus shall be provided for the full length of panel. Terminal boxes with single gland trifucating cable box suitable for 11KV aluminium XLPE (E) cable of size 3C x 300sqmm for incoming & outgoing &Suitable for TOP CABLE ENTRY All control wiring necessary for the above including interconnections. The size of the conductor should not be less than 1.5sqmm, FRLS insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per standard practice. b.7 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays NOTE: 11K.V. HT Panel shall be Expandable from both side HT Panel Designation :11kV HT Panel at HEB Load Centre-2 as per tender Electrical SLD ref GE-P-FAC-Ele00-01-06-155000-R5: Sh1 of 3 / Spring
1 Set 2,693,250 -
1.4
Sr.No a
ITEMS DESCRIPTION Incomers: Complete Incomers section shall be as per above panel of Load cetner-1 & suitable for 2 Incomers Outgings : Each outgoing feeders shall be as per above panel of Load cetner1 & suitable for 1 Outgoing NOTE: 11K.V. HT Panel shall be Expandable from both side
Qty
Unit
1 Set 4,037,250 -
1.5
HT Panel Designation :11kV HT Panel at LEB Load Centre-3 as per tender Electrical SLD ref GE-P-FAC-Ele00-01-06-155000-R5: Sh1 of 3 Incomers: Complete Incomers section shall be as per above panel of Load cetner-1 & suitable for 3 Incomers VCB panel Outgings : Each outgoing feeders shall be as per above panel of Load cetner1 & suitable for 1 Outgoings VCB feeders panel. NOTE: 11K.V. HT Panel shall be Expandable from both side NOTE FOR ALL 11 KV HT PANEL: ALL 11k.V. HT PANELS SHALL BE SUITABLE TO TOP CABLE ENTRIES FOR INCOMING AND OUTGOINGS CABLES TERMINATIONS.
2.1
Battery Charger BATTERY CHARGER AT MRS: Supply, Installation ,Testing & commissioning of 110 Volts-350-AH-Battery with battery charger with full wave rectifire ,independent 3 Phase charger for Float & Boost at Main Reciving Station ( Input voltage 3 Phase 415 Volts) with wall mounted DCDB, Suitable for bottom cable entries for incoming and all outgoing cables The Configuration of DCDB shall be as under Incomer : 1No 250 Amp ,DP MCCB ,35kA , Outgoing : 32Amp , DP MCB 10kA - 12Nos BATTERY CHARGER AT EACH LOAD CENTERS :Supply, Installation ,Testing & commissioning of 110 Volts-100-AH-Battery with battery charger with full wave rectifire ,independent 3 Phase charger for Float & Boost ( Input voltage 3 Phase 415 Volts) with DCDB as under Incomer : 125 Amp ,DP MCB ,10kA -1 No Outgoing : 32Amp , DP MCB 10kA - 6Nos TRANSFORMERS Supply,Taking deliver at site storing at site, shifting from the place of storage to the place of installation, installation,with all fittings and accessories, testing and commissioning. Drying out and oil filteration till adequate values of insulation resistance of windings and break down value of oil are achieved is included in the scope. 5000 kVA, 33/11 kV with vector group of Dyn-11 with OLTC & RTCC.The transformer shall be as per latest IS 2026. The transformer shall be suitable for Outdoor installation as per tender specification /drawinhs & with HT & LT Cable box for indoor cable terminations & as per tender Data sheet. Refer Drawing no GE-P-SITEELE01-01-05-155008 for Location of Transformer installation. ( Note: Civil foundation will be provided by other)
Set
351,645
10,500
351,645
10,500
2.2
Set
219,240
7,000
657,720
21,000
3.1
No
2,845,500
77,000
2,845,500
77,000
Supply,Installation ,testing & commissioning of Open ventilated Dry type Transformer with Off circuit tap changing link to Primary Side,with Cable box for Incoming and Busduct for outgoing etc & as per latest I.S.11171: 1985 specification. Rating & details of Transformer is as under.The transformer shall be suitable for Indoor installation as per tender drawing reference GE-P-SITE-Ele00-01-08-155012 & tender data sheet. KVA Rating :2000KVA, %Z 6.25% Primary Volts : 11kV 50 HZ Secondary Volts : 433 Volts 50 HZ Type of cooling : Air Natural Type of tap & Range: LINK : +5%,-7.5 % in the steps of 2.5 % IP Degree : 31 LIGHTING TRANSFORMERS: Supply,Installation ,testing & commissioning of Dry type Transformer with Off circuit tap changing link to Primary Side,with Cable box for Incoming and Busduct for outgoing etc & as per latest I.S.11171: 1985 specification. The transformer shall be suitable for Indoor installation as per tender drawing reference GE-P-SITE-Ele00-01-08155012 & tender data sheet.The rating of Transformer is as under KVA Rating :250KVA, %Z 5% Primary Volts : 415 Volts 50 HZ 3 No
3.2
No
2,514,750
35,000
7,544,250
105,000
3.3
375,000 -
15,000 -
1,125,000 -
45,000 -
10
Sr.No
ITEMS DESCRIPTION Secondary Volts : 415Volts 50 HZ Type of cooling : Air Natural Type of tap & Range: LINK : +5%,.5 % in the steps of 2.5 % IP Degree : 31 Supply & installation of Transformer yard gate made out of 40mm dia GI pipe 11/2" 8 SWG GI wire mesh and two leaves gate with clear width of 3000 mm. Supply & installation 8 SWG GI wire 1 1/2" mesh chain link fencing of 1.8 Mtr. height with 50 x 50x 6 MS angle at every 2 M interval and 50 x 50 x6 Angle at top. The fencing should be painted with 2 coat of red oxide primer with Aluminium paint BUSDUCT Supply ,Taking delivery at site, shifting from the place of storage to the place of installation between Transformer secondary to Main PCC ,unpacking, site assembly of loose accessories, installation testing and commissioning of the following LT.Busdcuts & its accessories including required support ,etc of following ratings.The required M.S. support for installation of busduct shall be measured under boq item no------------- of M.S .Steel items . The route/ location of busducts shall be as per tender drgawing no GE-P-SITE-Ele00-0108-155012&GE-P-SITE-Ele00-01-08-155013.
Qty
Unit
3.3
No
3.4
Mtr
40,348 -
4.1
4.1.1 Straight Run 3200 Amp TPN, 50kA, AL Busduct Indoor 4.1.2 Right Angle Bend 3200 Amp, 50kA 4.1.3 Bimetallic Flexible Transformer end connections (3-ph & Neutral) 4.1.4 Wall frame assembly with fire barrier
4.3
3200Amp TPN -AL BUSWAY SYSTEM: 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 and 4.3.1 designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious. The testing scope also includes testing of all buseays joint by theremographic meter . The busways shall be installed as per Tender Drawing referenceGE-P-FAC-Ele01-01-18154988. The required M.S. support for installation of busduct shall be measured under boq item of M.S .Steel items a b c d e f g h i j k 3200 amp TPN Aluminium Feeder busway with 65KA short circuit with stand for 1 sec. Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted in running meters) Provision of 'T' with joint (Horizontal) ( meterage will be counted in running meters) Provision of Edgewise cross with joint Adaptor Box suitable for above busways Reducers of following ratings 3200A/800A 3200A/630A 500 10 4 6 8 8 8 3 4 4 Mtr Nos Nos Nos Nos Nos Nos Nos Nos Nos
40,085 19,879 24,781 22,493 23,147 34,720 35,476 54,463 46,725 45,675
1,000 2,100 3,500 2,100 2,100 2,100 2,100 2,100 2,100 2,100
20,042,295 198,786 99,123 134,959 185,173 277,763 283,811 163,390 186,900 182,700
500,000 21,000 14,000 12,600 16,800 16,800 16,800 6,300 8,400 8,400
11
Sr.No
ITEMS DESCRIPTION
Qty
Unit
800 Amp TPN -AL-RISING MAINS : 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with 4.3.2 bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 and designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious.The rising mail shall be provided plug at 2 points in each length of 3 meter of busways( i.e. only 2 tapings) 800 amp TPN Aluminium Plug in busway with 30KA short circuit with stand a for 1 sec.(2 plugs) b Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running c meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in d running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted e in running meters) f Adaptor Box g Spring hangers h End Cover 630 Amp TPN -AL-RISING MAINS : 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with 4.3.3 bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 and designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious.The rising mail shall be provided plug at 4 points in each length of busways( i.e.2 Nos to each side of Busways) 630 amp TPN Aluminium Plug in busway with 30KA short circuit with stand a for 1 sec.(2 plugs) b Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running c meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in d running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted e in running meters) f Adaptor Box g Spring hangers h End Cover Tap off boxes box: Supplying ,installing of 4Poles MCCB With LSG release 4.3.4 , 3 CT Operated Dual KWH meter with RS 485 Serial communication Ports, rotary handle etc.of following ratings a 800Amp 50 k.A. b 630Amp 50 k.A. Plug in box : Supplying, installing,testing and commissioning of TPN plug in 4.3.5 box of of following capacity on above horizontal bus system complete with TPN MCCB 30KA, electrical interconnections, earthing etc as required. Plug in type type box with rating 315Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box
440 20 10 4 4 10 150 4
440 20 10 4 4 10 150 4
2,100 1,680 3,500 1,680 1,680 1,680 350 350 700 560 -
4,945,248 107,457 66,728 24,263 24,961 97,262 611,415 5,040 1,513,109 799,903 -
924,000 33,600 35,000 6,720 6,720 16,800 52,500 1,400 2,800 2,240 -
4 4
No No
378,277 199,976 -
UR
No
32,190
350
Plug in type type box with rating 250Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 200Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 125Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 100 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 63 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 32 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box LT Switchgear
No
12,162
280
12,162
280
c d e f g
10 8 4 5 40
No No No No No
12
Sr.No
ITEMS DESCRIPTION Supply, assembly, factory test, loading,Taking delivery at site storing at site & supervision at site of LT panel board as per IS 8623/1993, indoor type free standing,in various shipping section, Form 4b in construction, ALUMINIUM BUS BAR , IP54 , fabricated out of 3 mm CRCA Sheet etc & as per specifications. Each panel shall comprising as per followings & Enlcosed ELECTRICAL SLD along with Tender Technical Specifciations.(All panels shall be with TOP and exit of cables.)
Qty
Unit
5.1
Panel Designation: PCC FOR LOAD CENTER-1 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):8000 (L) x1500 (W) x 2375 (H) Location : Load Center-1
1 No. 2,479,311 1 No. 838,332 1 No. 972,414 1 No. 564,544 419,382 419,382 1 No. 434,082 1 No. 336,694 650,907 1 No. 3,679,305 1 No. 3,350,672
15,000 6,500 3,500 2,000 1,500 1,500 2,000 1,000 2,500 35,000 25,000
2,479,311 838,332 972,414 564,544 419,382 419,382 434,082 336,694 650,907 3,679,305 3,350,672
15,000 6,500 3,500 2,000 1,500 1,500 2,000 1,000 2,500 35,000 25,000
5.2
Panel Designation: MLDB OFFICE & CAFETARIA BLDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3000 (L) x450 (W) x 2025 (H) Location : Load Center-1
5.3
Panel Designation: 675kVAR APFC PANEL 1- ( Load Centre) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 4000 (L) x800 (W) x 2375 (H) Location : HT/LT Substation Room at Factory Load Centre-2 Note: The APFC Relay shall be intelligent microprocessor type with RS 485 serial communication port suitable for minimum 12 stages & 2 Sets of relays shall be considered in each APFC Panel Panel Designation:PDB FOR CAFETARIA Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Panel Designation:PDB OFFICE -2A Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Panel Designation:PDB OFFICE -2B Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location :
5.4
5.5
No.
5.6
No.
5.7
Panel Designation:PDB KITCHEN & BASEMENT VENTILATION PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3500 (L) x800 (W) x 2375 (H) Location : Panel Designation:LIFT PDB(-Office and cafetaria ) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3500 (L) x800 (W) x 2375 (H) Location : Panel Designation:UTILITY PUMP MCC Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Location : Chiller Room
5.8
5.9
No.
5.10 Panel Designation :PCC For Load Centre-2(HEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 6500 (L) x1500 (W) x 2375 (H) Location : Load Centre-2 5.11 Panel Designation: PCC For Load Centre-3(LEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 6500 (L) x1500 (W) x 2375 (H) Location : Load Centre-2
13
Sr.No
ITEMS DESCRIPTION
Qty
Unit
Unit Rate: Rs Supply Installation 3,500 4,500 4,000 4,500 3,500 1,500 1,500 2,000 2,000 3,000 1,800 750 -
Amount ( Rs ) Supply Installation 4,157,120 494,719 560,869 1,137,817 815,931 377,119 266,869 452,888 854,326 169,491 437,757 432,244 7,000 4,500 4,000 4,500 3,500 1,500 1,500 4,000 8,000 3,000 1,800 750 -
5.12
Panel Designation:675kVAR-RT- APFC Panel at Factory Load Centre 2&3 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 4000 (L) x800 (W) x 2375 (H) Location : Load Centre-2&3 Note: The APFC Relay shall be intelligent microprocessor type with RS 485 serial communication port suitable for minimum 12 stages & 2 Sets of relays shall be considered in each APFC Panel 5.13 Panel Designation: MLDB-1 - for Factory Building (LEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):1800 (L) x450 (W) x 2025 (H) Location : Load Centre-3 5.14 Panel Designation: MLDB-2 - for Factory Building (HEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):1800 (L) x450 (W) x 2025 (H) Location : Load Centre-2 5.15 Panel Designation:HVAC &OTHER UTILITIES PDB -1 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):4500 (L) x800 (W) x 2375 (H) Location : Load Centre-2 5.16 Panel Designation:HVAC &OTHER UTILITIES PDB -2 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):4500 (L) x800 (W) x 2375 (H) Location : Load Centre-3
No.
2,078,560 -
No.
494,719 -
No.
560,869 -
No.
1,137,817 -
No.
5.17 Panel Designation: PDB -LOAD CENTER-2 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Load Centre-3 5.18 Panel Designation: PDB -LOAD CENTER -3 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Load Centre3
815,931 -
No.
377,119 -
No.
5.19 Panel Designation : -3 -Phase 32 Amp -SOCKET OUTLET PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155012 - R0 & annexure-1 Approx.Overall dimension ( in mm ):2400 (L) x800 (W) x 2375 (H) Location : HEB & LEB FACTORY SHED 5.20 Panel Designation : -1- Phase 20 Amp -SOCKET OUTLET PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155012 - R0 & annexure-1 Approx.Overall dimension ( in mm ):2400 (L) x800 (W) x 2375 (H) Location : HEB & LEB FACTORY SHED 5.21
266,869 -
Panel
No.
226,444 -
Panel
No.
213,582 -
Panel Designation :UPS Input D.B. 2X60 k.V.A-FACTORY EMERGENCY LIGHTING Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155008 - R0 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : Load Center-3 Panel Designation :UPS Output D.B. 2X60 k.V.A-FACTORY EMERGENCY LIGHTING Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155008 - R0 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : Load Center-3
No.
169,491 -
5.22
1 1
No. No
5.23 Panel Designation :A.C. D.B- -Utility Building(35k.A. ) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : MRS Building
437,757 432,244 -
14
ITEMS DESCRIPTION
Qty
Unit
Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of following rating UPS with ,15 Min battery backup , with static & manual bypass Input Voltage: 3 Ph 415 Volts, 10% Output : 3 -Phase-415Volts 4w 50 Hz 2% , The scope also includes supply, Installation, Testing and Commissioning with flooded lead-acid batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries & also TVSS at the input of each UPS to protect against transients, surges & Noise as per the tender specifications 80k.V.A. UPS(Factory Office W.S.) Application & suitable for Parallel operation with communication facilities. 60k.V.A. UPS Lighting Application & suitable for Parallel operation with communication facilities. 10k.V.A. UPS for Server application (Independent application) Note :Above UPS system shall be suitable for Parallel operation on Separate Power Distribution Boards. Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of 10 KVATrue- On Line sine wave invertor with ,30 Min battery backup , Input Voltage: 3 Ph 415 Volts, 10% Output : 3 Phase-415Volts 4w 50 Hz 2% , The scope also includes supply, Installation, Testing and Commissioning with flooded lead-acid batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. (1No Dedicated invertor for MRS Internal Emergemcy Lighting & 1 No Dedicated for Emergency lighting of Basement of Load center-1 ) TPN -ISOLATORS Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of TPN 415 Volts Heavy duty Isolators of following rating, The complete assembly shall be with 2 mm thick CRCA metalic enclosure, Finished paints, IP 65 Degree of protection , Padlock arrangements & Suitable incoming & outgoings cables termination arrangements. 400Amps -TPN 315Amps -TPN 250Amps -TPN 200mps -TPN 125Amps -TPN 100Amps -TPN 63Amps -TPN UP TO 32Amps -TPN TOTAL OF SECTION B-SUBSTATION EQUIPMENTS C 1 SECTION -C -CABLES AND CABLE TERMINATIONS LT CABLES Supply,taking delivery at site, unloading at site,Installation,testing & commisioning of XLPE Insulated, PVC sheathed, armoured, 650/ 1100 V grade power and control cables to be laid in trenches, on cable trays, burried in ground. Civil work for cables to be laid burried in ground such as excavation, backfilling, sand and brick protection and cable tray /tray supports are measured separately and Miscellaneous items such as saddles, clamps, cleats, cable tags/ cable markers etc. are included in the scope 3.5.C x 400 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 300 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 240 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 185 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 150 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 120 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 95 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 70 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 2C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 4C x 25 Sq.mm.A2XFY(XLPE- AL-Armoured) 3C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 400 8000 1100 1400 1800 300 1000 1300 1350 1250 300 900 3700 UR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR UR UR UR UR UR UR 6 36 26 Nos Nos Nos Nos Nos Nos Nos Nos Nos
2,478,000 -
35,000 -
6.4
Set
173,250
7,000
346,500
14,000
1.1
1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9 1.1.10 1.1.11 1.1.12 1.1.13 1.1.14
1,265 882 725 572 471 396 314 255 183 141 116 116 136 161
506,000 7,057,600 797,390 800,800 847,440 118,800 313,500 331,760 246,510 176,000 34,650 103,950 504,680
48,000 800,000 110,000 112,000 144,000 21,000 70,000 78,000 81,000 62,500 45,000 -
15
Sr.No 1.1.15 1.1.16 1.1.17 1.1.18 1.1.19 1.1.20 1.1.21 1.1.22 1.1.23 1.1.24 1.1.25 1.1.26 1.1.27 1.1.28 1.1.29 1.1.30 1.1.31 2 2.1
ITEMS DESCRIPTION 3C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3CX10Sq.mm. XFY(XLPE -CU-Armoured) 3CX4Sq.mm. XFY(XLPE -CU-Armoured) 3CX2.5 Sq.mm. XFY(XLPE -CU-Armoured) 4CX16Sq.mm. A2XFY(XLPE- AL-Armoured) 4CX10Sq.mm. A2XFY(XLPE- AL-Armoured) 4CX10Sq.mm. XFY(XLPE -CU-Armoured) 4CX6 Sq.mm.XFY(XLPE -CU-Armoured) 4CX4Sq.mm. XFY(XLPE -CU-Armoured) 4CX2.5Sq.mm. XFY(XLPE -CU-Armoured) 4CX1.5Sq.mm. YWY(PVC -CU-Armoured) 2CX10Sq.mm. XFY(XLPE -CU-Armoured) 2CX4Sq.mm. XFY(XLPE -CU-Armoured) 19CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 24CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 5CX2.5 Sq.mm. WY(PVC -CU-Un-Armoured Flexible ) LT cable Terminations : LT cable Termination : Supply & installation of Termination of XLPE insulated, PVC sheathed, 650/1100 V grade, armoured cable including stripping of cable insulation, supplying and fixing of Aluminum / tinned plated copper lugs and crimping the same to the conductor, supply and fixing of double compression cable glands including all 'labour supply and consumable material required for jointing / termination. 3.5.C x 400 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 300 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 240 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 185 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 150 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 120 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 95 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 70 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 2C x 25 Sq.mm.A2XFY(XLPE- AL-Armoured) 3.5C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 4C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3CX10Sq.mm. XFY(XLPE -CU-Armoured) 3CX4Sq.mm. XFY(XLPE -CU-Armoured) 3CX2.5 Sq.mm. XFY(XLPE -CU-Armoured) 4CX16Sq.mm. XFY(XLPE -CU-Armoured) 4CX10Sq.mm. XFY(XLPE -CU-Armoured)) 4CX10Sq.mm. XFY(XLPE -CU-Armoured) 4CX6 Sq.mm. XFY(XLPE -CU-Armoured) 4CX4Sq.mm. XFY(XLPE -CU-Armoured) 4CX2.5Sq.mm. XFY(XLPE -CU-Armoured) 4CX1.5Sq.mm. YWY(PVC -CU-Armoured) 2CX10Sq.mm. XFY(XLPE -CU-Armoured) 2CX4Sq.mm. XFY(XLPE -CU-Armoured) 19CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 24CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 5CX2.5 Sq.mm. WY(PVC -CU-Un-Armoured Flexible ) Note: Aluminum Lugs shall be used for AlLUMINUM Conductor Cables & Copper Lugs for COPPER Cables
Qty UR UR UR UR 25000 1000 15500 450 600 1800 3000 200 UR UR 125 125 UR
Unit MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR
Unit Rate: Rs Supply Installation 121 99 267 86 95 35 88 30 348 30 222 30 161 25 105 25 77 25 396 70 399 80 25
49,500 49,913 -
8,750 10,000 -
2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 2.1.8 2.1.9 2.1.10 2.1.11 2.1.12 2.1.13 2.1.14 2.1.15 2.1.16 2.1.17 2.1.18 2.1.19 2.1.20 2.1.21 2.1.22 2.1.23 2.1.24 2.1.25 2.1.26 2.1.27 2.1.28 2.1.29 2.1.30 2.1.31
36 32 14 20 6 2 8 22 16 14 4 14 46 UR UR UR UR UR 2000 40 550 30 40 70 60 20 UR UR 30 24 UR
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
2,977 2,643 2,570 1,658 1,649 1,114 940 835 679 600 395 395 401 180 422 345 345 257 257 212 184 461 721 -
350 300 300 250 250 200 200 180 180 120 120 150 120 120 100 60 80 100 100 60 60 60 60 60 40 40 100 150 35 -
107,172 84,576 35,980 33,160 9,894 2,228 7,520 18,370 10,864 8,400 1,580 5,530 18,446
12,600 9,600 4,200 5,000 1,500 400 1,600 3,960 2,880 1,680 480 2,100 5,520
TOTAL OF SECTION C- CABLES SECTION -D-CABLE TRAYS & ASSOCIATED WORKS Supply and fixing of followings sizes pre galvanized factory fabricated GI Ladder type cable tays, including straight runs, bends, reducers, Tees, cross members ,couplings, earth continuity flexible conductor for each joints,anchor fastners, supports,drilling,cuttings,nuts, bolts, required civil works etc to complet the work. The required MS support shall be measured under M.S. steel BOQ item no-------------------------750 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 600 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 50 Mtr. 671 611 200 140 -
1.1
1.2
2000
Mtr.
33,550 1,221,000 -
10,000 280,000 -
16
Sr.No 1.3
ITEMS DESCRIPTION 450 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 300 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 100 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C
Qty 100
Unit Mtr.
1.4 1.5
50
Mtr.
1.6
UR
Mtr.
Mtr. Mtr. Mtr. Mtr. Mtr. 1,095 913 732 550 308 809 655 501 341 187 200 140 140 105 105 140 105 105 70 63 1,095,600 219,450 440,000 184,800 32,725
Supply and fixing of perforated type GI cable trays of the following sizes as per specification. UR 750 mm x 75 x 75 x 2 mm thick 1200 600 mm x 75 x 75 x 2 mm thick 300 450 mm x 75x 75 x 2 mm thick 800 300 mm x 75x 75 x 2 mm thick 600 150 mm x 50 x 50 x 2 mm thick Supply and fixing of GI cable trays covers of 2 mm thick including all necessary fixing arrangement,hardware, consumable etc . Suit to following GI perforated and ladder type cable trays . 750 600 450 300 150 mm x 75 x 75 x 2 mm thick mm x 75 x 75 x 2 mm thick mm x 40 x 40 x 2 mm thick mm x 40 x 40 x 2 mm thick mm x 25 x 25 x 2 mm thick UR 50 UR UR UR
Supply, Installation,testing & Commissioning, of MS Powder Coated with RAL 7032 Race Ways ,for fixing high bay light fitting at10 to 12 M. from finished floor leve,. fabricated out of 14 gauge MS CRC sheet to form C type channel raceway with cover on side(Screw Fixed Type) of size 4000 100x50x50 to be suspended with rods / sleek guyrope / clutch wire from true ceiling /roof for mounting of tube light fitiings. All supporting membere shall be equvillant to GRIPPLE OR PROFAB Make supporitng members/ structures.. Supply, fabrication and installation of cable tray cable tray supports, supports for cable trench covers, supporting frame for mounting of control panels, supports for mounting of local control station,Main Electrical Panel,lighting panel, lighting fixture etc. with 2 coats of enemel primer and 2 coats of epoxy paint Note - The rates shall be inclusive of grouting of supports , Anchor fastner,welding rods, nut,bolts,clamps,and any other consumable which required to complete the works. TOTAL OF SECTION D- CABLE TRAYS SECTION -E-EARTHING Supplying and laying of G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by welding overlapping ) UR 75 mm x 10 mm 9000 50 mm x 10 mm UR 25 mm x 6 mm 7500 25 mm x 3 mm (For street light & power socket earthing) 25 mm x6 mm (Cu) with Brazing joint (For metering Kiosk & Transformer 300 neutral) 50 50 mm x6 mm (Cu) with Brazing joint 500 8 SWG GI wire UR 14 SWG GI wire 200 12 SWG GI wire G.I.earthing bus, 750mm Long x 50x10mm with supporting insulators & all 200 Hardwares Tin plated CU.earthing bus, 750mm Long x 50x6mm with supporting 80 insulators & all Hardwares UR Lightning air terminal 25 mm dia copper rod 1500 mm Long 1core x70 Sq.mm cu cable ,green colour with yellow strip FRLS PVC 1200 insulation (For UPS, L.E.B m/c, CNC m/c & Welding m/c earthing) Providing earthing stations at locations as called for including providing and laying 3 Mtr Long x 65mmDia G.I. electrode with 50 x 6 mm thick G.I. strip, To form earth electrode with inspection chamber,Watering funnel with 20 gauge G I wire ,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines /Boaring, Charcoal, salt, or Bentonie slurry etc) For MSDCL Metering Kiosk.
Mtr
400
45
1,600,000
180,000
35
MT
63,000
20
2,205,000
700
7,110,500
849,150
1 1.1 1.2 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.12 1.13
Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Nos. Nos. No. Mtr.
916800
42000
18
No
9,500
2,100
171000
37800
17
Sr.No
ITEMS DESCRIPTION Supply,Installation,Testing and commissioning of earth pit of size 600 x 600 x 3 mm copper plate with GI water pipe 2.7 mtr long x19mm dia , buried in earth pit with charcoal and salt each in alternative layers including excavation re-filling etc. all as per enclosed drawing, with C.I.legend identification marker.The complete earth pit shall be as per IS 3043. The scope also includes with inspection chamber,Watering funnel with 20 gauge G I wire ,,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines , Charcoal, salt, or Bentonie slurry etc) (For UPS,Transformer & DG Neutral earthing)
Qty
Unit
22
No
9,500
2,100
209000
46200
Supply, testing and commissioning earthing stations as per IS 3043, maintenance free earthing pit of mild steel hot dep galvanised. The pipe shall be insterted one inside the another. The pipe shall be filled & packed with highly conductive and anti corrosive mixture with following diamension. The scope also includes with inspection chamber,Watering funnel with 20 gauge G I wire ,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines /Boaring, . Length - 3000mm Outer Pipe Dia - 76mm Inner Pipe Dia. - 38mm 300 X 150mm chamber shall be provided for inspection and connection. 50mmx6 mm thick copper strip shall be nut bolted to connect the earthing strips/Leads The electrode shall be provided with two chemical compound bags (20Kg each) Make : Ashlok,Fast Track, JEF LIGHTNING PROTECTION SYSTEM Supply & Installation of ESE Lightning Rod , with Stainless Steel Body, working on the Principle of (ESE) Early Streamer Emission technology, which will offer LEVEL 1 protection for 79 Mtrs radius when mounted at a height of 5 mtrs from the plane to be protected, complying to NFC 17 102. Type- Early Streamer Emission Make & Model - CIRPROTEC (NIMBUS) Matrerial Used - Corrosion resistant stainless steel body Construction Details => The electronic circuit of the ESE rod shall be encapsulated in an epoxy mould to avoid derating or degradation due to atmospheric conditions. This also makes the Lightning rod weather proof and suitable for installation in highly corrosive atmosphere.The rods shall be made of Corrosion Resistant Stainless body conforming AISI 316 grade. The Lightning rod shall be self powered type and shall not require any form of external power supply/batteries for its operation. . Conformity to standards - As per NF C17-102 and UNE 21186-96 Radius of Protection(M) - 79M level 1 Construction Details - Lightning Rods shall be manufactured according to UNE 21.186-96 and NF C17-102 standards . Sensors-Type - Electronic equipped with triggering device Test Reports -Should have been tested at an internationally accredited Laboratory and CPRI , Bangalore and the necessary test reports to be attached. Shall be designed to check the integerity of the electronics periodically with a tester 4 DIGIT ELECTROMECHANICAL Lightning Transient Event counter ,in a IN WEATHER PROOF ENCLOSURE shall be mounted in 1.5 Mtrs from the ground level Each lightning protection set shall be comprising with followings devices a Main Lightning Air terminal suitable for protection of Radious of 80 meter from its base of 5 Meter height for Level III Protection. GI Elevation pole with a reducer to fix the LA unit, Base Plate, Clamps and all required fixing accessories ( Ready to Install). Test Clamp to connect the down conductor to the earth termination and disconnect the down conductor from the earth termination for regular checks of the earth termination resistance value. 1 Set of Remote Control unit required only for testing the Prevectron air terminal.
9,500
2,000
798000
168000
84
No -
5.1
Set
123,530
7,500
864710
52500
18
Sr.No
ITEMS DESCRIPTION Lightning Flash Counter. Electronically controlled, register every strike between 1000 A to 100 KA for a 8/20 microsecond peak current. Tested in High Voltage Laboratory (CPRI).
Qty
Unit
5.2
Nos.
15,400
1,000
107800
7000
TOTAL OF SECTION- E- EARTHING (GROUNDING) F 1 SECTION F D.G.SETS DIESEL GENERATOR SET Supply Transporation, Unloading at Place of installations,, installation, testing and commissioning of radiator cooled 1000 KVA prime (actual) rating diesel generating set (11000 Volts Alternator with PCCM or equivalent) along with day oil fuel tank, CT Adaptor Box, AVM Pads including cable termination box with all associated equipment / work as per specifications. Alternator shall have class H insulation 11000 Volts and rated for 800 KW output. Engine shall not be derated upto 50 deg.C ambient and suitable for bearing the starting current after changeover. The scope also includes providing foundation details drawings to Engineer In Charge (Foundation will be provided by Civil scope of works), Liasioning work from Govt Authorities Like Electrcial Inspector, MIDC, Pollution control Boards etc. The scope also includes filling first oil ,fuel for commissioning. Supply, installation, testing and commissioning of powder coated acoustic enclosure suitable for 1000 KVA DG set for indoor application as per specification complete with all accessories as required including ventilation system. No deration in DG set capacity shall be accepted on this account. The scope also includes providing foundation details drawings to Engineer In Charge (Foundation will be provided by Civil scope of works), Liasioning work from Govt Authorities Like Electrcial Inspector, MIDC, Pollution control Boards etc. Supply, erection, testing and commissioning of exhaust piping Min. 6mm Thick of following sizes with welding joint including bends, MS pipe supports, clamps, dash fastener, nuts, bolts etc.,with first layer of insulation 25mm thick ceramic fiber wool (96Kg/Cub. Mtr.) & second layer minimum 50mm thick rockwooll (150Kg/Cub Mtr.) covered with 26 SWG aluminium sheet claddings etc. complete as required and as per specifications.
7,829,260
992,450
1.1
Nos
9,000,000
30,000
18,000,000
60,000
1.2
Nos
1,000,000
10,000
2,000,000
20,000
1.3
a b
55 35
Mtrs Mtrs
8,800 6,550 85 -
2,500 2,000 25 56 42 35 42 42 -
1.4
Exhaust pipe supporting system with M.S channel, M.S angle, M.S flat, dash fastners, nut, bolt etc. complete including 1 coat of redoxide & 2 coat of 5000 enamel paint and other Accessories as required at the site of work.
K.G.
1.5 a b c d e f
ELECTRICAL PLC / SCADA Application Interface cables Supply & Installation( PVC Screened Copper cables) 24C x 1.5 Sq.mm PVC screened cable 8C x 1.5 Sq.mm PVC screened cable 4C x 1.5 Sq.mm PVC screened cable ( For Electronic Governer ) 12 C x 0.5 Sq.mm PVC screened Triad cable ( for temperature scanner ) Profi bus 2 wire Communication cable
1.6
Supply, installation, testing and commissioning of D.G Set Automatic Synchronizing panel suitable for,11k.V.26.2k.A. ,2 x 1000k.V.A. D.G. Set as per Technical specification & enclosed Single line diagram ( Drg. No GE-PFAC-Ele00-01-08-155003 ) The Specification for D.G. Autosynchronizing Panel shall be as per HT Panel items reference sr 1 of section B
Set
4,200,000
12,000
4,200,000
12,000
Supply, installation, testing and commissioning of NEUTRAL GROUNDING RESISTOR (NGR) panel suitable for Each D.G. Set of 1000k.V.A. as per Technical specification & enclosed Single line diagram ( Drg. No GE-P-FACEle00-01-08-155003 ) The Complete NGR Panels shall be comprising followings parameters. NGR Element : Resistance: 121Ohms & 52.48 Amps at 11/ 3 k.V. 1 No 400Amp-12k.V. Single Pole Vacumm contactor with Auxiliary contacts 3 Nos 75/1Amp CL -PS CT with internal wiring & terminals IP Degree of complete NGRVPanel : IP65 TOTAL OF SECTION- F- GENERATOR SET 2 Nos
1.7
225,000 -
5,000 -
450,000 26,700,250
10,000 499,600
19
Sr.No G
ITEMS DESCRIPTION SECTION -G-LIGHTING FIXTURES/EXHAUST FANS Supply, installation, testing and commissioning of luminaires complete with, lamps, ballast, starter, HPF condenser, standard down rod, connecting cord, The rate shall include all necessary fixing accessories like MS hooks, MS supports, fasteners, with all necessary hardware, accessories as required for complete installation. Quoted rate shall exclude the cost of earthing . Note: Catalogue numbers indicated are only to describe type of light fixture required. Lamp Colour shall be - 84 or as approved by Architect / Consultant. Supply Installation, testing & commissioning of 2x28 W T5 with electronic ballast equivallent to GE cat no GET CI 2X28 C/S HF.The scope also includes all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X1.6 mm thick G.I. steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core wires and earthing , fastening accessores etc as required to complete the work
Qty
Unit
1.1
50
Nos
1,260
280
63,000
14,000
4X54W T5 Highdbay Luminaire Equivallent to GE Cat Ref ELC454 with Lamps of 4 X54W FTL T5 with dimmable choke suit for dimming control, on M.S. raceway mouted on 12-14 Meter elevation including arrangement of all cherry pickers, loopings of 3 core 1.5 Sq.mm Flexible FRLS insulated cables from looping junction boxe to each fitting NOTE.:- Race will supply 7 instaalation will be measured separetly. (No welding will allowed)
1.2
875
Nos
4,883
350
4,272,188
306,250
420 -
582,120 -
73,920 -
1.4
95 W LED IP 66 Street light fixture to fixed on 7.5 to 9 Meter hight poles including supply and pulling of 3 Core x 1.5 Sq..mm Cu Flexible ,-FRLS cables from Pole mouted looping junction box to each fitting terminals 150W HPMV Integral Post top light fixture equivallent to GE cat no DUNAADCMH150W TU including supply and pulling of 3 Core x 1.5 Sq..mm Cu Flexible ,-FRLS cables from concealed looping junction box to each fitting terminals, including providing concealed 25 mm PVC pipes for incoming cables to Looping junction box & up to each light fittings, 42 W LED Recess mounted decorative luminaries equivallent to GE cat no GCRO42.56 MO with all accessories and tube etc., including supplying and fixing ball and socket arrangement 2 nos /Flexible SS Chains/ or 2 no. down rods of 20 mm dia X1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 3 Corex 1.5 sq. mm FRLS insulated, copper conductor, cable and earthing etc as required.
176
Nos
3,308 -
1.5
Nos
7,560
490
60,480
3,920
1.6
Nos
2,310
280
1.7 2X28W FTL T5 Surface Mounted with clear Acrylic cover Luminaire with electronic ballast equivallent to Wipro cat no WCF 50228 SGW including required clamps , fastners ,connection to fittings etc to fixed in staircase etc. 10 Nos 1,418 1.8 2 x18 W Decorative Recess mounted Down lighter equivallent to GE cat no GECFLC2X36DNLR(H) HF with required hanging support from ceiling Nos 1,208 1.9 1 x18 W Decorative Recess mounted Down lighter equivallent to GE cat no GECFLC2X18DNLR(H) HF with required hanging support from ceiling Nos 3,833 150 W MH Integral Flood light Luminaire Equivallent to GE cat no 1.10 GEMF1X150CAI with required support to fixed on top plate of 7.5 Mtr high street light pole 400 W MH Integral Flood light Luminaire Equivallent to GE cat no ZF400 1.11 KRC .The fitting shall be installed on top mounting plate of 16 Mtr high lighting mask. Note for above light fittings items i All light fittings quantities shall be procured as per Final approved Drawings by architect & approval from client /Architects for sample of each light fittings. Connection of lighting fixtures from ceiling rose / junction box by flexible copper wires in flexible conduit/M.S. ball and socket arraqngment is included in the conduit down rod, scope The structural supports for suspension of lighting fixtures are measured seperately Supply,& Installation of Exhaust fans of following ratings 8 Nos 5,460 UR Nos -
14,175 43,680 -
2,100 1,960 -
ii iii 2
20
Sr.No
ITEMS DESCRIPTION
Qty
Unit
2.1
Supply, of Exhaust fan Heavy duty 230 V AC 50 Hz 305 mm 1400 RPM with condenser complete erected in position with n/c materials Fan motor with moisture treatment and class E insulation & With bird protective screen
30
No
2.2
Supplying of capacitor type1200 mm sweep ceiling fan complete with down rod, blades, shakle etc. with high breeze, high speed for operation on 230V, 50 Cy. Single phase A.C. supply confirming to IS 374-1979 and with double ball bearing system The fan shall be green rated as per BEE norms. Supply of 750 mm sweep-1 Ph 240 Volts 50 Hz Wall/Column Mounted Air cirulated fans including Inbuilt speed regulator Including all necessary fixing hardware,Anchor fastner etc. Almonard make Supply & Fixing of Ceiling mounted (surface/flush) high performance, Movement Detector with the coverage of 6Mtrs dia complete with necessary Sensor control wiring.vWIPRO Cat ref COP 11010 OR Hager make EE805 or Schneider make CSS54E-WE or Bajaj Make - Bajaj-Leviton OSC 10MOW TOTAL OF SECTION G- LIGHTING LUMINARIES
Nos
1,890
175
350 -
806,400 -
28,000 -
2.4
Nos.
7,560
280
6,049,943
440,650
H 1
SECTION :H: SUPPLY & PROVIDING OF POINT WIRING AND ACCESSORIES. POINT WIRING -IN M.S. CONDUITS Primary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 2 Nos 2.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG black stove enemelled steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Primary light point up to 5 meter length Primary light point up to 8 meter length Primary light point up to 10meter length Secondary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 3 Nos 1.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Secondary light point up to 2 meter length Secondary light point up to 4 meter length Secondary light point up to 5meter length Secondary point Wiring for twin control light point with 1.5 sq.mm FR LS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR LS insulated copper conductor single core cable etc as required. Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Power plug wiring in M.S. Black stove condiut (2 x 4 sq.mm) - Wiring for power plug with 2X4 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25 mm dia M.S. Black stove conduit along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in M.S. Black stove condiut (2 x 2.5 sq.mm) - Wiring for power plug with 2X2.5 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25mm dia,M.S. Black stove conduit along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. 25 20 20 Point Point Point 10 20 20 Point Point Point
1.1
a b c
1.2
a b c
1.3
UR
Point
1,424
25 35 40 -
1.5
Mtr
475
35
1.6
Mtr
437
25
21
Sr.No
ITEMS DESCRIPTION Power plug wiring in M.S. condiut (4 x 4 sq.mm )- Wiring for powersocket outlet with 4X4 sq. mm. FRLS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25 mm. dia M.S. black stoved enemelled conduit along with 2 nos. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. POINT WIRING -IN PVC CONDUITS Primary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 2 Nos 2.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Primary light point up to 5 meter length Primary light point up to 8 meter length Primary light point up to 10meter length Secondary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 3 Nos 1.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Secondary light point up to 3 meter length Secondary light point up to 5 meter length Secondary light point up to 8meter length Secondary point Wiring for twin control light point with 1.5 sq.mm FR LS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR LS insulated copper conductor single core cable etc as required. Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Power plug wiring in PVC condiut (2 x 4 sq.mm) - Wiring for power plug with 2X4 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in PVC condiut (2 x 2.5 sq.mm) - Wiring for power plug with 2X2.5 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in PVC condiutt (4 x 4 sq.mm )- Wiring for powersocket outlet with 4X4 sq. mm. FRLS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 2 nos. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Wiring Accessores for Raw power & UPS Power socket outlets S/F GI Box along with modular plate: Supplying and fixing following size /modules, GI box along with modular base & cover plate for modular switches in recess etc as required. The scope also includes cutting of wall, block works, & POP of walls with mesh after plate fixing & other related civil works to make surface good . 1 or 2 Module(75mmx75mm) 3 Module (100mmX75mm) 4 Module (125mmX75mm) 6 Module (200mmX75mm) 8 Module (125mmX125mm) 12 Module (200mmX150mm)
Qty
Unit
1.7
Mtr
516
45
2.1
a b c
2.2
a b c
2.3
UR
Poit
1,273
15 20 25 -
2.5
Mtr
273
20
2.6
Mtr
248
15
2.7
UR
Mtr
1,084
3.1
a b c d e f
UR UR UR UR UR UR
No No No No No No
25 25 30 35 35 50 -
22
Sr.No 3.2 a b c d e f
ITEMS DESCRIPTION Supply & fixing following modular base and cover plate for modular switches in recess etc as required. 1 or 2 Module 3 Module 4 Module 6 Module 8 Module 12 Module Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Raw Power /UPS Power socket outlets) 5/6 amps switch 15/16 amp switch 3 pin 5/6 amp socket outlet 6 pin 15/16 amp socket outlet
Qty
Unit
UR UR UR UR UR UR
No No No No No No
3.3 a b c d
UR UR UR UR
No No No No
3.4
Supply and providing of Power plug wiring in Raceway in office (2 x 4 sq.mm) - Wiring for light/power plug with 2X4 sq. mm. , FR LS insulated, copper conductor, single core cable in existing surface/recessed raceway along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required.(UPS & Raw Power Power)
UR
Mtr
122
10
Supply and providing of Power plug wiring in Raceway in office (2 x 2.5 sq.mm) - Wiring for light/power plug with 2X4 sq. mm. , FR LS insulated, copper conductor, single core cable in existing surface/recessed raceway along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required.(UPS & Raw Power Power) Supply, fixing, laying and embedding in UNDER FLOOR ALUMINUM of following sizes complete with all accessories including junction box with 2 mm thick Stainless steel cover plate,neoprene gasket in joints ,cutting the floor and jamming the raceway with all necessary hardware (including civil works) as required. 50 x 38 x 2 mm 100 x 38 x 2 mm 150 x 38 x 2 mm 200 x 38 x 2 mm 300 x 38 x 2 mm Supply, fixing, commissioning of following sizes access outlet with all accessories, cutting the floor and jamming the access outlet with all ncessary hardware (including civil works) as required. 250x250x60- 75 mm three compartment. 265x265x53- 80 mm three compartment. Supply , fixing, commissioning of following sizes cross over/ junction box with 3 mm thick cover plate with all accessories cutting the floor and jamming the junction box with all necessary hardware including civil works as required. 250x250x60- 75 mm three compartment. 300x300x60- 80 mm three compartment. UR UR Nos Nos UR UR UR UR UR Mtr Mtr Mtr Mtr Mtr
3.5
UR
Mtr
110
a b c d e 5
40 60 95 125 130 -
a b
UR UR UR
6 a b
93,235
21,500
Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR LS insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. Typical Raw Power & UPS Power Final D.B. Application (Ref Tender drawing no GE-P-FAC-Ele00-01-11-1550013) Incomer : 63 A,4 pole, MCB 10k.A. C-CL Outgoing :As under 16 - 25A-2P-RCBO 30m.A.:15 Nos (5 Nos/Phase) 20 No
1.1 65,000 -
23
Sr.No 1.2 (a) (b) i ii 1.3 (a) (b) i ii 1.4 (a) (b) i ii 1.5
ITEMS DESCRIPTION Typical Lighting D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-111550011) Incomer : 63 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 36 Nos(12 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:36 Nos(12 Nos Per Phase) Typical Lighting D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-111550011) Incomer : 63 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 18 Nos(6 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:18 Nos(6 Nos Per Phase) Typical E. L. D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-11-1550010) Incomer : 25 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 12 Nos(4 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:12 Nos(4 Nos Per Phase)
Qty 12
Unit Nos
Unit Rate: Rs Supply Installation 50,000 1,200 900 800 1,500 1,500 500 650 -
Amount ( Rs ) Supply Installation 600,000 210,000 480,000 160,000 80,000 15,000 88,000 14,400 5,400 12,000 3,000 1,500 500 2,600 -
Nos
15
Nos
2 Area Street light Final D.B. for Street Lights as under Incomer : 125 Amp -4 Pole MCCB + 1 No 4 Pole-110 Amp Moduler Contractor Outgoing 12 Nos 32 Amp TP MCB 10K.A. CL + 32Amp 4 Pole ELCB -30m.A. per Outgoings& 24 Hrs Timer + Photo Cell with Manual / Auto Selctor switch, Interface provision with BMS & its control wiring etc. 1 Flood Light Mast lighting PDB.as under Incomer : 100 Amp -4 Pole MCCB , + 1No4 Pole-110 Amp Moduler Contractor + 24 Hrs Timer + Photo Cell with Manual / Auto Selctor switch, Interface provision with BMS & its control wiring etc. Outgoing 10 Nos 32Amp 25k.A. TP-MCCB-LS -Release. D.B. Server system Incomer : 63 A,DP,MCB type Isolator Outgoing : 25 A DPMCB- 10k.A -D-CL10 Nos per Phase Security Kiosk D.B. as under Incomer : 63 A,4 pole, MCB 10k.A. C-CL +4 Pole 63 Amp ELCB 100m.A. Outgoing : As under a. 12 Nos 20 A SPMCB- 10k.A -C-CL (4 Nos /Phase) b. 4 Nos 32 A -TP MCB 10k.A. C-CL Supply, Installation, Testing & Commissioning of Following Readymade Industrial Power Sockets with neccessory cable end boxes.The each socket outlet shall be installed at fabricated M.S. Supports/ Frames suit to Sokcet outelt dimensions. The required steel shall be measured under M.S. Fabrication item of this BOQ. 1
No
1.6
No
1.7
No
1.8
No
3 Pin, 20 Amp, 230 Volts Industrial switch socket outlet sheet steel enclosed IP54 with 1 No. earthing terminal 'controlled by -SPN MCB 10K.A -C-CL and provided with chain and 'cover and suitable for loop in loop out of 3 x 2.5 'sq.mm XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body. Combine Industrial switch Socket Out Let : 5 Pin 32A, TPN, 415 Volts Industrial switch socket controlled by 4 Pole MCB 10K.A. C-CL & 3 Pin, 20 Amp, 230 V industrial switch socket out let controlled by-SPN MCB 10K.A .-C-CL , sheet steel enclosed indoor type with 2 Nos. earthing terminals and provided with chain & cover suitable 'for loop in loop out of 3.5C x 35 sqmm A2XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body. 5 Pin 63A, TPN, 415 Volts Industrial switch socket controlled by 4 Pole MCB 10K.A. C-CL industrial switch socket out let sheet steel enclosed indoor type IP-54 with 2 Nos. earthing terminals and provided with chain & cover suitable 'for loop in loop out of 3.5C x 35 sqmm A2XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body.
2.1
100
Set
6,640
350
664,000
35,000
2.2
28
Set
10,630
490
297,640
13,720
2.3
Set
24,774
630
99,096
2,520
24
Sr.No
ITEMS DESCRIPTION METAL MCB BOXES (IP 42) : Supply & fixing of MCB Box enclosed in 1.6mm thick, CRCA sheet steel box. The box shall be concealed / Surface in the wall. The plate cover is properly aligned & flush with the wall surface all materials will be in contractor scope. 20A SP MCB - 01 No. in Metal BOX 20A SP MCB - 02 No. in Metal BOX 20A SP MCB - 03 No. in Metal BOX
Qty
Unit
Amount ( Rs ) Supply Installation 13,400 27,060 44,880 4,079,076 1,875 2,250 3,000 127,765
25 30 40
TOTAL OF SECTION I- FDB /SSO/LDS SECTION -J-EXTERNAL LIGHTING Supply & installation of hot deep galvanized (internally & externally) Octogonal cross section pole with base plate as per IS 2629 with ,supply and fixing of 2 Nos. of 63 mm dia PVC pipes for cable entry,with inside cable termination,earth connection & with weatherproof door & locking facility 3Nos. 2.5 sq.mm stranded copper flexible wires with MCB control (Minimum Overall Height 8.00 M,3mm thick, bottom dia 200mm,top dia 76 mm,bottom plate 275 mm x 275 mm x 20 mmthick. Including concrate foundation & foundation bolts.(The weather proof Loop In Loop Out junction box with all accessories shall be integral part of street light Poles) Single bracket Double bracket 50 mm dia G.I. bracket mouted street light poles(Max 3 Mtr Length) 183 3 2 No No No
1.0
Flood Light Mast As under Supply of 16M high mast shaft in two sections suitable for 39 m/sec wind speed, with raising lowering system comprising, head frame, luminaries carriage suitable to install 8 nos luminaries in symmetrical arrangement, double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightening finial.The scope of works also includes installation including supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. and concreeting including excvation,cement, etc to complete the works.Each lighting mast shall be provided with followings electrical requirement & accessoris. (Note: Contractor to submit required vendor shop drawings for complete Flood light mast system with calculation from structural consultant for foundation before commence of work)
2.1
Set
323,946
60,000
1,619,730
300,000
Supply of non-integral floodlight luminaries type Equvillent to GE Cat ref ZF 400KRC with one no. 400 W MH(KRC) T lamps With control gear boxes 2.1.1 The scope also includes Supply and fixing of 3 x 2.5 Sq.mm Cu-Armoured Cables from each Control gear to each light fittings & its connection with Weather proof D.C. Gland .: 8 Nos to each lighting mast . Supply of single dome aviation obstruction lights of type BJAOL 1 with one nos no. 25 W Neon lamp : 2 Set to each lighting mast & individual Armoured 3x2.5 cu cable connection for the same from its control panel to neon lamp terminals . Supply of out door, Weather proof IP65 Feeder Pillar as per following 2.1.3 specification to each Lighting Mast Incomer:32Amp 4 Pole MCB ,10k.A.,C-Class & 32 Amp 4 Pole ELCB 30m.A. a. +RYB LED Indication+Space Heater with Thermostat. b Outgoing as under b.1 8Nos SP MCB,16Amp,10k.A., B-Class for lighting circuit b.2 2 No 16 Amp DP MCB,10k.A., B-Class forAviation light 1 DOL Feeder for suitable winch motor as per vendor design & with b.3 necessary indication & control system for "LOWER& RAISE" of mast. b.4 16 Amp 10k.A.,B-Class SP MCB controlled 5/15Amp Socket Outlet 2.1.2 TOTAL OF SECTION J- EXTERNAL LIGHTING K 1 SECTION -K -MISCELLANEOUS : Supply,Installation,Testing & commissioning of the following - of the following Supply, Installation, testing and commissioning of start stop local control stations of LM6 material with momentary type PB for stop, start and latch and 1 No. earthing terminal suitable for 4 x 1.5 sq.mm - YWY cable
3,972,390
761,000
1.1
25
Sr.No i ii 1.2
ITEMS DESCRIPTION Outdoor, weatherproof type with IP 65 protection Indoor type with IP54 protection Junction box fabricated from 16 SWG sheet steel with screwed gasketed cover and 1 No.earth terminal duly painted with two coats of red oxide and two coats of aluminium paint and to receive 4 Nos. 3 x 2.5 sq.mm YWY cables complete with Elmex terminals. (Minimum size100mm x 100mm x 75mm) Note : Structural supports for mounting are measured separately
Qty UR UR
850
No.
1.3
Floor mounted bucket stand with buckets to hand 4 nos. of 13 ltrs buckets. The stand shall be 5'(L) x 3'(H) x 2"(W) made out of 30 x 300 x 4mm MS angle frame duly coated with 2 coats of red oxide primer & 2 coats of red finish paint Supply and installation of GI pipe class B on wall / steel structure / under floor including bending / treading etc 38 mm dia 50mm dia 75mm dia 100 mm dia 150 mm dia
Set
UR UR UR UR UR
Supply and installation of 2c x 2.5 sq.mm copper flexible wire Cable Markers as per Std. Drawing H.T. Cable marker L.T. Cable Marker Earthing Tag Marker as per Electrical Inspectorate requirement Saftey Equipmnt Antiskid black rubber mat of approved make,12 mm thick 900mm wide x 1800mm Long chequered type as per IS-5424 in following voltage grade(Jyothi Make)
UR
Mtr.
15 5 103
5.1.1 415 V voltage grade 5.1.2 33 kV voltage grade 5.1.2 11 kV voltage grade 6 7 First Aid box with all the standard contents. First aid chart made of cloth for electricall shock treatment printed in English ,& Hindi duly framed with front glasses. Pair of rubber gloves and gumboots 33 kV grade 11 kV grade Metallic danger boards. 33 kV 11 kV 415 V Portable 5 kg. dry type fire extinguisher suitable for electrical fire and as recommended by the tariff advisory committee. Supply and fixing of the following charts / drawings duly framed with front glass Single line diagram Outdoor lighting and cable layout Supply and installation of RCC hume pipe as under 300 mm dia Half Round Pipe( For Incoming HT cable from Overhead Line to Metering Room)
60 5 30 3
No.
8 8.1 8.2 9 i i ii 10
1 3
No. No.
2 3 3
No.
Unit Rate: Rs Supply Installation 441 49 3,000 500 315 70 315 70 315 70 930 35 2,500 35 1,800 35 1,000 35 189 35 600 600 175 35 175 35 175 35 6,400 210 105 105 70 56
374,850 6,000 -
41,650 1,000 -
4,725 1,575 32,445 55,800 12,500 54,000 3,000 567 600 1,800 350 525 525 6,400 2,250 1,500 8,505 -
1,050 350 7,210 2,100 175 1,050 105 105 70 105 105 210 315 210 1,050 -
11 i ii 12 12.1
3 2
No. No.
15 UR
RMT RMT
26
ITEMS DESCRIPTION
Qty UR
Unit RMT
4 way Flame proof Junction box suitable for installation in hazardous area with IP 65 Protection as per IS 12063/1897 & Gas group IIA & IIB & 1 No.earth terminal inside & 2 terminal outside duly painted with two coats of red oxide and two coats of aluminium paint and to receive 4 Nos. 3 x 2.5 sq.mm YWYcables complete with Elmex terminals. Flame proof Rotary Switches suitable for installation in hazardous area with IP 65 Protection as per IS 12063/1987 & Gas group IIA & IIB & 1 No.earth terminal inside & 2 terminal outside & to receive 3 Nos. 3 x 2.5 sq.mm YWY cables TOTAL OF SECTION K- MISC.
UR
No
14
UR
No
SECTION- L-CIVIL WORKS Excavation & Back filling of cable trenches in following soil conditions Soft soil Murum Hard Rock Supply and laying of sand for cables. Supply and laying of burnt bricks for cables as per standard practice Supply and Spreading of gravel 40mm size, 100 mm thick with duly levelling of Transformer pit TOTAL OF SECTION L- CIVIL WORKS 650 485 485 325 14500 15 Cum Cum Cum CU.Mtr Nos Cu Mtr
Unit Rate: Rs Supply Installation 480 70 2,520 2,100 3,150 2,100 350 715 1,750 2,700 700 9 2 3,500 300 -
567,917
56,860
27
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
A.
SECTION A-HT. SECTION(CABLES & TERMINATION) HT Cables Supply, taking delivery ,unloading at site,Installation,testing & commissioning of HT XLPE insulated, UE grade, cables, as per IS 7098 , burried in ground such as excavation up to 1 meter depth , backfilling, sand and brick protection and cable tray / tray supports are measured separately and Miscellaneous items such as saddles, 3 mm thick aluminum clamps, cleats, cable tags/ cable markers etc. are included in the scope.(The testing shall including HI-POT test at site before commissioning of the system & Test voltage shall be as per IS 7098) 3Cx300 Sq.mm 33kV XLPE-UE- Cable 100 3Cx300 Sq.mm 11kV XLPE -UE-Cable UR 3Cx240 Sq.mm 11kV XLPE -UE-Cable 4972 Note: No straight through joints will be allowded for any single length of cables. CABLE TERMINATIONS : Supply,installation,testing & commisioning of Heat shrikable type cable termination kit with long head Crimping type Lugs, for following XLPE insulated, (UE) grade cable including necessary Right angle /straight insulating boots. The scope also includes thermography test of all terminations at loads by using Themo graphic meter. Indoor type 3Cx300Sq.mm 33kV XLPE-UE- Cable 3Cx300 Sq.mm 11kV XLPE -UE-Cable 3Cx240 Sq.mm 11kV XLPE -UE-Cable Mtr. Mtr. Mtr. 1723.8 1185.41 1028.024 10% 10% 10% 172 119 103 1,896 1,304 1,131 120 120 120
4 UR 38
2.2 Outdoor type 2.2.1 3Cx240 Sq.mm 33kV XLPE-UE- Cable 2.3 Straight Through Joint 2.3.1 3Cx300 Sq.mm 11kV XLPE -UE-Cable 2.3.2 3Cx240 Sq.mm 11kV XLPE -UE-Cable 3 Supply, Installation, Testing and commissioning 33kV Distribution Class Lightening Arrestors with cross arm (1 Set of 3 Nos) Supply installation testing and commissioning of 33kV CT& PT Metering kiosk including approval ,testing from MSEDCL .Detailes of CT & PT shall be as per MSEDCL load sanctionapproval.(Without T.O.D. meter) Supply & installation H.T. Static Three Vector T. O. D. Meter as per MSEDCL.The scope also including calibration & testing of meter from MSEDCL G. I. Pipe-CL -B- 150mm dia.for supporting of HT Cables connected to Overhead Lines ,road crossing etc for MSEDCL incoming cable. HD PVC Pipe 150mm dia.for supporting of HT Cables connected to Overhead Lines ,road crossing etc for MSEDCL incoming cable. TOTAL OF SECTION A- HT SECTION B SECTION -B-HT/LT SUB-STATION EQUIPMENT
No.
25000
10%
2,500
27,500
2,100
UR UR 1
No
343,741
343,741
7,500
No
44,100
44,100
2,100
15
Mtr
1,575
1,575
210
UR
Mtr
Supply, assembly, factory test, loading,Taking delivery at site storing at site & supervision at site of HT panel board indoor type free standing,in various shipping section, Form 4b in construction, IP4X , fabricated out of 3 mm CRCA Sheet etc & as per specifications. Each panel shall comprising as per followings & Enlcosed ELECTRICAL SLD along with Tender Technical Specifciations.The panel shall be suitable for top cable entries for Incoming and outgoing cables except 33 k.V. HT Panels which shall be from bottom. HT Panel Designation:33k.V.Main HT Panel at point of supply: 33-KV-Indoor free Vacuum circuit breaker panels with 1250 Amp Aluminum busbar ,26.2 k.A.-1 Second ,EDO Type for Transformer Feeder with over currents & Auxiliary Protection of Oil Cooled transformer and as per enclosed electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 & as per followings requirements. One (1) No. 33 KV,1250 A VCB/26.2 KA rupturing capacity at 33 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings. Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 30k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT with double wound,100- 225/1+1+1 with metering and protection core.
1.1
Set
9,900,000
5%
495,000
10,395,000
a.1
a.2
a.3 a.4
a.4.1 Core 1: 15VA burden for Differential Protection(86) protection ( Class PS) a.4.2 Core 2:15VA burden of metering ( accuracy class 1.0) a.4.3 Core 3: 30VA burden for OC/EF protection ( Class 5P-20)
a.5
Voltage transformer with each , 3 limbs connected in star, dual class , 33kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.) Protectives Relays as under
a.6
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
a.6.1
Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
a.6.1 Stand by Earth Fault relay (51G) a.6.1 Restricated Fault relay (64R) a.6.1 Transformer Auxiliary Protection Relays (63Tx) a.6.1 Trip circuit supervision relay (95). a.6.1 Antipumping relay a.6.1 Lockout relay (86) a.6.1 Under /Over Frequency Relay(81) a.6.1 Under /OverVoltgae Relay(27/59) a.6.1 Reverse Power relay (32) a.6.1 Breaker Failure Relay (52BF) a.7 Control & wiring terminals
All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. a.7.2 a.8 Test terminal block fuses, circuit lables , phase indication lamps etc. as per Electrical SLD Meterings as under Voltmeter range 0-33KV with necessary voltmeter selector switch & suitable for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses. Ammeter range (0-100-225A) with necessary ammeter selector switch dual graduated scale, 96x96 sqmm dial with shrouded terminal . Multifunction Digital meter with RS 485 Serial Communication Port for following parameters. Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,KVA KWH KVAH RKVAH p.f. TDH a.9 Other Accessories as under & as per technical specifications
a.8.1
a.8.2
a.8.3
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. / Spring
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 16 Window Announciator for Transforemr Faults a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 a.10.5 a.10.6 a.10.7 a.10.8 a.10.9 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays NOTE: Above VCB Panel shall be suitable for expandable type for future suit to One incomers & two outgoings feeders. 1.2 HT Panel Designation: 11k.V.Main HT Panel at MRS 11-KV-Indoor Vacuum circuit breaker panels with 1250 Amp, Aluminum busbar 26.2 k.A.-1 Second , EDO Type with over currents ,earth fault Protections. The complete panel shall be as per enclosed electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 with Tender Technical specifications & as per followings requirements. a a.1 EACH INCOMERS 2 Sets of 11 KV,1250 A VCB/26.2 KA rupturing capacity at 11 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings.
Set
9,090,000
5%
454,500
9,544,500
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
a.2
Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 9k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT with double wound, 350-800Amp/1+1+1 with metering and protection core.
a.3 a.4
a.4.1 Core 1: 15VA burden for Differential (87) protection ( Class PS) a.4.2 Core 2:15VA burden of metering ( accuracy class 1.0) a.4.3 Core 3: 30VA burden for OC/EF protection ( Class 5P-20)
a.5
Voltage transformer with each , 3 limbs connected in star, dual class , 11kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.) Protectives Relays as under Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
a.6 a.6.1
a.6.2 Stand by Earth Fault relay (51G) a.6.3 Restricated Fault relay (64R) a.6.4 Differential Protection relay (87R) a.6.5 Trip circuit supervision relay (95). a.6.6 Antipumping relay a.6.7 Lockout relay (86) a.6.8 Under /OverVoltgae Relay(27/59) a.6.9 Reverse Power relay (32) a.6.10 Breaker Failure Relay (52BF) a.6.11 Master lock out relay (86) a.7 Control Wiring & Terminal All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. a.7.2 a.8 Test terminal block fuses, circuit lables , phase indication lamps etc. as per Electrical SLD Meterings Voltmeter range 0-12KV with necessary voltmeter selector switch & suitable for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses. Ammeter range (0-350-800A) with necessary ammeter selector switch dual graduated scale, 96x96 sqmm dial with shrouded terminal . Mutifunction Digital meter with RS485 Serial Communication Port for following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,KVA KWH KVAH RKVAH p.f. TDH a.9 Other Accessories as under & as per technical specifications
a.8.1
a.8.2
a.8.3
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. / Spring
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 8 Window Announciator for Faults a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays Outgoings VCBs Five (5) Nos. 11 KV, 1250 A VCB/ 26.2 KA rupturing capacity at 11kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the following: Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. Cast Resin CT with double wound, with metering and protection core. CT.Ratio as indciated on Electrical SLD for each outgoing VCB in MRS room panel 15VA burden for protection ( Class 5P-20) 15VA burden of metering ( accuracy class 1.0)
b.2
b.3
b.4
Protection to each outgoings Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
Trip circuit supervision relay (95). Lockout relay (86) Antipumping relay
b.5
Other Accessories as under & as per technical specifications Necessary DC supply healthy LED type indication lamp & switch. Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement. Danger plate (As per specification) Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. Three pin socket + switch. Anticondensation space heater / thermostat 50x6mm, copper earth bus shall be provided for the full length of panel. Terminal boxes with single gland trifucating cable box suitable for 11KV aluminium XLPE cable of size 3C x 300sqmm for incoming & outgoing &Suitable for TOP CABLE ENTRY All control wiring necessary for the above including interconnections. The size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per standard practice. / Spring
b.6
Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Numerical Relays
c c.1
BUS COUPLERS: 2Nos Bus couplers VCB Panel comprising as under As per above Outgoing VCB Breaker panels except No CT for metering & no meters. 3 Nos Bus PT Section: 3Nos Withdrawable type BUS PT section as shown in Tender Electrical SLD Ref GE-P-FAC-Ele00-01-011-155000-R5Sh No 1 of 03 NOTE: 1: Above Panel shall be suitable for Expandable type from both Side NOTE: 2: Control Voltgae Bus for D.C. & AC votlage shall be as per Electrica SLD ref.GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 NOTE: 3: Interlocks and control logics shall be suitable for 4 Incomers & 3Bus-Couplers as shown in above mentioned SLD
1.3
HT Panel Designation :11kV HT Panel Office Load Centre-1 as 11-KV-Indoor Vacuum circuit breaker panels with 1250 Amp,26.2 k.A.-1 Second , EDO Type with over currents ,earth fault Protections. The complete panel shall be as per enclosed electrical SLD Ref GE-P-FACEle00-01-011-155000-R5- Sh No 1 of 03 with Tender Technical specifications & as per followings requirements.
Set
2,565,000
5%
128,250
2,693,250
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
a.1
11 KV,1250 A,Aluminum Busbar VCB/26.2 KA rupturing capacity at 11 kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the followings. Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. 9k.V. ,10k.A.Class-III Zno Surger Arrestor Cast Resin CT with double wound, 250-Amp/1+1 with metering and protection core.
a.2
a.3 a.4
a.4.1 Core 1:15VA burden of metering ( accuracy class 1.0) a.4.2 Core 2: 30VA burden for OC/EF protection ( Class 5P-20)
a.5
Voltage transformer with each , 3 limbs connected in star, dual class , 11kV/3/110V/3 with drawable type with automatic shutters 100 VA burden with HRC fuses for primary & secondary .( Confirming related IS specs.)
Protectives Relays as under to each Incomers Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, a.6.1 consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) . a.6.1 Trip circuit supervision relay (95). a.6.2 Antipumping relay a.6.3 Lockout relay (86) a.6.4 Under /OverVoltgae Relay(27/59) a.6.5 Reverse Power relay (32) a.6.6 Breaker Failure Relay (52BF) a.6.7 Master lock out relay (86) a.7 Control Wiring & Terminal All control wiring necessary for the above including interconnections. The a.7.1 size of the conductor should not be less than 1.5sqmm, PVC insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per Electrical SLD GE-P-FAC-Ele00-01-011-155000-R5- Sh No 1 of 03 Meterings to each Incomers Voltmeter range 0-12KV with necessary voltmeter selector switch & suitable for 110V AC 96x96sqmm dial with shrouded terminal & protection fuses. Mutifunction Digital meter with RS485 Serial Communication Port for following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KW,k.V.A KWH KVAH RKVAH p.f. TDH a.9 Other Accessories as under & as per technical specifications
a.6
a.7.2
a.8
a.8.1
a.8.2
a.9.1 Necessary DC supply healthy LED type indication lamp & switch. a.9.2 Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement.
a.9.3 Danger plate (As per specification) a.9.4 Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. / Spring
a.9.5 Three pin socket + switch. a.9.6 Anticondensation space heater / thermostat a.9.7 8 Window Announciator for Faults a.9.8 Hooter with Accept & Reset Push Button a.10 a.10.1 a.10.2 a.10.3 a.10.4 a.10.5 a.10.6 a.10.7 a.10.8 a.10.9 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
b b.1
Note: E& M Interlocaks shall be provided as indicted on Tender Electrical SLD for both Incomers Outgoings VCBs One (1) Nos. 11 KV, 1250 A VCB/ 26.2 KA rupturing capacity at 11kV rated metal clad, floor mounting, horizontal isolation horizontal drawout type complete with the following: Manually & motor operated (230V AC), spring charged trip free type, VCB incorporating mechanical as well as electrical ON/OFF indication, spring charge/discharge mechanical indication"OFF" push button test/service position limit switches with 4NO/4NC breaker auxilary contacts in service position. Cast Resin CT with double wound, with metering and protection core. CT.Ratio as indciated on Electrical SLD for each outgoing VCB in MRS room panel 15VA burden for protection ( Class 5P-20) 15VA burden of metering ( accuracy class 1.0)
b.2
b.3
b.4
Protection to each outgoings Over current 50,50N Insutantaneaus short circuit 51,51N & one earth fault element with numerical IDMT relay with shunt trip on 110volts DC, consisting 3 element over current relay with setting from 50 to 200% (step of 25%) and earth fault with setting from 20 to 80% (step of 10%) .
Trip circuit supervision relay (95). Lockout relay (86) Antipumping relay b.5 Metering : Mutifunction Digital meter with RS485 Serial Communication Port for following parameters Line & Phase Voltage Line Current Frequency M.D. KVA Meter KWH KWH KVAH RKVAH p.f. TDH b.6 Other Accessories as under & as per technical specifications Necessary DC supply healthy LED type indication lamp & switch. Control : T-N-C ( Trip , Neutral & Close) breaker control switch with indicating arrangement. Danger plate (As per specification) Set of Indication for circuit breaker ON/OFF/Trip on Fault charged/Trip circuit healthy/Test/Service positions etc. Three pin socket + switch. Anticondensation space heater / thermostat 50x6mm, copper earth bus shall be provided for the full length of panel. Terminal boxes with single gland trifucating cable box suitable for 11KV aluminium XLPE (E) cable of size 3C x 300sqmm for incoming & outgoing &Suitable for TOP CABLE ENTRY All control wiring necessary for the above including interconnections. The size of the conductor should not be less than 1.5sqmm, FRLS insulated, copper wire where required. Test terminal block fuses, circuit lables , phase indication lamps etc. as per standard practice. b.7 Followings wirings duly brought out to terminal block for BMS/SCADA interface by using twisted pair shielded wires in side the HT. Panels Potenial free (DI)contact of VCB -ON -Status Potenial free (DI)contact of VCB -OFF -Status Potenial free (DI) contact of VCB -Trip On Fault- Status VCB in TEST position (DI) Status VCB in Serive position (DI) Status ON Command to VCB(DO) OFF Command to VCB(DO) RS 485 (AI) of Mutifunction meters RS 485 (AI) of Numerical Relays NOTE: 11K.V. HT Panel shall be Expandable from both side HT Panel Designation :11kV HT Panel at HEB Load Centre-2 as per tender Electrical SLD ref GE-P-FAC-Ele00-01-06-155000-R5: Sh1 of 3 Incomers: Complete Incomers section shall be as per above panel of Load cetner-1 & suitable for 2 Incomers Outgings : Each outgoing feeders shall be as per above panel of Load cetner-1 & suitable for 1 Outgoing NOTE: 11K.V. HT Panel shall be Expandable from both side / Spring
1.4
Set
2,565,000
5%
128,250
2,693,250
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
1.5
HT Panel Designation :11kV HT Panel at LEB Load Centre-3 as per tender Electrical SLD ref GE-P-FAC-Ele00-01-06-155000-R5: Sh1 of 3 Incomers: Complete Incomers section shall be as per above panel of Load cetner-1 & suitable for 3 Incomers VCB panel Outgings : Each outgoing feeders shall be as per above panel of Load cetner-1 & suitable for 1 Outgoings VCB feeders panel. NOTE: 11K.V. HT Panel shall be Expandable from both side NOTE FOR ALL 11 KV HT PANEL: ALL 11k.V. HT PANELS SHALL BE SUITABLE TO TOP CABLE ENTRIES FOR INCOMING AND OUTGOINGS CABLES TERMINATIONS.
Set
3,845,000
5%
192,250
4,037,250
2.1
Battery Charger BATTERY CHARGER AT MRS: Supply, Installation ,Testing & commissioning of 110 Volts-350-AH-Battery with battery charger with full wave rectifire ,independent 3 Phase charger for Float & Boost at Main Reciving Station ( Input voltage 3 Phase 415 Volts) with wall mounted DCDB, Suitable for bottom cable entries for incoming and all outgoing cables The Configuration of DCDB shall be as under Incomer : 1No 250 Amp ,DP MCCB ,35kA , Outgoing : 32Amp , DP MCB 10kA - 12Nos BATTERY CHARGER AT EACH LOAD CENTERS :Supply, Installation ,Testing & commissioning of 110 Volts-100-AH-Battery with battery charger with full wave rectifire ,independent 3 Phase charger for Float & Boost ( Input voltage 3 Phase 415 Volts) with DCDB as under Incomer : 125 Amp ,DP MCB ,10kA -1 No Outgoing : 32Amp , DP MCB 10kA - 6Nos TRANSFORMERS Supply,Taking deliver at site storing at site, shifting from the place of storage to the place of installation, installation,with all fittings and accessories, testing and commissioning. Drying out and oil filteration till adequate values of insulation resistance of windings and break down value of oil are achieved is included in the scope. 5000 kVA, 33/11 kV with vector group of Dyn-11 with OLTC & RTCC.The transformer shall be as per latest IS 2026. The transformer shall be suitable for Outdoor installation as per tender specification /drawinhs & with HT & LT Cable box for indoor cable terminations & as per tender Data sheet. Refer Drawing no GE-PSITE-ELE01-01-05-155008 for Location of Transformer installation. ( Note: Civil foundation will be provided by other)
Set
334,900
5%
16,745
351,645
2.2
Set
208,800
5%
10,440
219,240
3.1
No
2,710,000
5%
135,500
2,845,500
3.2
Supply,Installation ,testing & commissioning of Open ventilated Dry type Transformer with Off circuit tap changing link to Primary Side,with Cable box for Incoming and Busduct for outgoing etc & as per latest I.S.11171: 1985 specification. Rating & details of Transformer is as under.The transformer shall be suitable for Indoor installation as per tender drawing reference GE-P-SITE-Ele00-01-08-155012 & tender data sheet. KVA Rating :2000KVA, %Z 6.25% Primary Volts : 11kV 50 HZ Secondary Volts : 433 Volts 50 HZ Type of cooling : Air Natural Type of tap & Range: LINK : +5%,-7.5 % in the steps of 2.5 % IP Degree : 31 LIGHTING TRANSFORMERS: Supply,Installation ,testing & commissioning of Dry type Transformer with Off circuit tap changing link to Primary Side,with Cable box for Incoming and Busduct for outgoing etc & as per latest I.S.11171: 1985 specification. The transformer shall be suitable for Indoor installation as per tender drawing reference GE-P-SITE-Ele00-01-08155012 & tender data sheet.The rating of Transformer is as under KVA Rating :250KVA, %Z 5% Primary Volts : 415 Volts 50 HZ Secondary Volts : 415Volts 50 HZ Type of cooling : Air Natural Type of tap & Range: LINK : +5%,.5 % in the steps of 2.5 % IP Degree : 31 Supply & installation of Transformer yard gate made out of 40mm dia GI pipe 11/2" 8 SWG GI wire mesh and two leaves gate with clear width of 3000 mm. Supply & installation 8 SWG GI wire 1 1/2" mesh chain link fencing of 1.8 Mtr. height with 50 x 50x 6 MS angle at every 2 M interval and 50 x 50 x6 Angle at top. The fencing should be painted with 2 coat of red oxide primer with Aluminium paint BUSDUCT Supply ,Taking delivery at site, shifting from the place of storage to the place of installation between Transformer secondary to Main PCC ,unpacking, site assembly of loose accessories, installation testing and commissioning of the following LT.Busdcuts & its accessories including required support ,etc of following ratings.The required M.S. support for installation of busduct shall be measured under boq item no------------- of M.S .Steel items . The route/ location of busducts shall be as per tender drgawing no GE-P-SITE-Ele00-01-08-155012&GE-P-SITE-Ele00-01-08155013. 3200A -TPN Busduct (Air Insulated type)
No
2,395,000
5%
119,750
2,514,750
3.3
No
375,000
375,000
3.3
No
12,034
12,034
3.4
Mtr
40,348
40,348
8,400
4.1
4.1.1 Straight Run 3200 Amp TPN, 50kA, AL Busduct Indoor 4.1.2 Right Angle Bend 3200 Amp, 50kA 4.1.3 Bimetallic Flexible Transformer end connections (3-ph & Neutral)
25 6 3
Mtr No Set
38,176
5%
22,493 24,781
5% 5%
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation 3200Amp TPN -AL BUSWAY SYSTEM : 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 4.3.1 and designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious. The testing scope also includes testing of all buseays joint by theremographic meter . The busways shall be installed as per Tender Drawing referenceGE-P-FAC-Ele01-01-18154988. The required M.S. support for installation of busduct shall be measured under boq item of M.S .Steel items 3200 amp TPN Aluminium Feeder busway with 65KA short circuit with stand for 1 sec. Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running c meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in d running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted e in running meters) Provision of 'T' with joint (Horizontal) ( meterage will be counted in running f meters) g Provision of Edgewise cross with joint h Adaptor Box suitable for above busways i Reducers of following ratings j 3200A/800A k 3200A/630A 800 Amp TPN -AL-RISING MAINS : 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with 4.3.2 bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 and designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious.The rising mail shall be provided plug at 2 points in each length of 3 meter of busways( i.e. only 2 tapings) 800 amp TPN Aluminium Plug in busway with 30KA short circuit with stand a for 1 sec.(2 plugs) b Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running c meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in d running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted e in running meters) f Adaptor Box g Spring hangers h End Cover a b 630 Amp TPN -AL-RISING MAINS : 3Pole and 100% neutral (TPN) busduct, totally enclosed in extruded Aluminium enclosure, dust proof with IP54 ingress protection,compact sandwitch type low inductance busduct with Tin Plated Aluminium throug out the length of busbars rated as under to withstand the stresses of suitable symmetrical fault levle at 415 Volts with 4.3.3 bends ,expansion joints. The bustrunking shall be as per IEC 60439-1&2 and designed for the temperature rise of 55 degree rise over ambient of 35 degree.Thermal stickers shall be provided at each joints for detection of temperature rise of 60/70/80 degree celcious.The rising mail shall be provided plug at 4 points in each length of busways( i.e.2 Nos to each side of Busways) 630 amp TPN Aluminium Plug in busway with 30KA short circuit with stand a for 1 sec.(2 plugs) b Joint suitable for above busway Provision of Flanged End with joint ( meterage will be counted in running c meters) Provision of 90deg. Bends with joint (Vertical) ( meterage will be counted in d running meters) Provision of 90deg. Bends with joint (Horizontal) ( meterage will be counted e in running meters) f Adaptor Box g Spring hangers h End Cover Tap off boxes box: Supplying ,installing of 4Poles MCCB With LSG 4.3.4 release , 3 CT Operated Dual KWH meter with RS 485 Serial communication Ports, rotary handle etc.of following ratings a 800Amp 50 k.A. b 630Amp 50 k.A. Plug in box : Supplying, installing,testing and commissioning of TPN plug in 4.3.5 box of of following capacity on above horizontal bus system complete with TPN MCCB 30KA, electrical interconnections, earthing etc as required. Plug in type type box with rating 315Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box 500 10 4 6 8 8 8 3 4 4 Mtr Nos Nos Nos Nos Nos Nos Nos Nos Nos 38,176 18,932 23,601 21,422 22,044 33,067 33,787 51,870 44,500 43,500
5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
UR
No
3,500
4.3
1,909 947 1,180 1,071 1,102 1,653 1,689 2,593 2,225 2,175
40,085 19,879 24,781 22,493 23,147 34,720 35,476 54,463 46,725 45,675
1,000 2,100 3,500 2,100 2,100 2,100 2,100 2,100 2,100 2,100 CAPEX ITEM-Offer from GE attached
440 20 10 4 4 10 150 4
5% 5% 5% 5% 5% 5% 5% 5%
2,100 1,680 3,500 1,680 1,680 1,680 350 350 CAPEX ITEM-Offer from GE attached
440 20 10 4 4 10 150 4
5% 5% 5% 5% 5% 5% 5% 5%
2,100 1,680 3,500 1,680 1,680 1,680 350 350 CAPEX ITEM-Offer from GE attached
9,263
3,882 1,200
4 4
No No
360264 190453
5% 5%
18,013 9,523
378,277 199,976
700 560
UR
No
30,658
5%
1,533
32,190
350
Plug in type type box with rating 250Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 200Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 125Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box
No
11,583
5%
579
12,162
c d
10 8
No No
11,583 11,583
5%
579 579
12,162 12,162
280 210
5%
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation
5%
Remark
e f g
Plug in type type box with rating 100 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 63 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box Plug in type type box with rating 32 Amp TPN MCCB-30KA Microprocessor LSG type with rotary handle on top of front of plug in box LT Switchgear Supply, assembly, factory test, loading,Taking delivery at site storing at site & supervision at site of LT panel board as per IS 8623/1993, indoor type free standing,in various shipping section, Form 4b in construction, ALUMINIUM BUS BAR , IP54 , fabricated out of 3 mm CRCA Sheet etc & as per specifications. Each panel shall comprising as per followings & Enlcosed ELECTRICAL SLD along with Tender Technical Specifciations.(All panels shall be with TOP and exit of cables.)
4 5 40
No No No
5%
5%
5.1
Panel Designation: PCC FOR LOAD CENTER-1 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 Panel annexure-1 Approx.Overall dimension ( in mm ):8000 (L) x1500 (W) x 2375 (H) Location : Load Center-1
R6 &
No.
2361249
5%
118,062
2,479,311
5.2
Panel Designation: MLDB OFFICE & CAFETARIA BLDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3000 (L) x450 (W) x 2025 (H) Location : Load Center-1
No.
798411
5%
5.3
Panel Designation: 675kVAR APFC PANEL 1- ( Load Centre) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 4000 (L) x800 (W) x 2375 (H) Location : HT/LT Substation Room at Factory Load Centre-2 Note: The APFC Relay shall be intelligent microprocessor type with RS 485 serial communication port suitable for minimum 12 stages & 2 Sets of relays shall be considered in each APFC Panel Panel Designation:PDB FOR CAFETARIA Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Panel Designation:PDB OFFICE -2A Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Panel Designation:PDB OFFICE -2B Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location :
39,921 -
838,332 972,414 564,544 419,382 419,382 434,082 336,694 650,907 3,679,305 3,350,672 2,078,560 494,719 -
No.
926109
5%
46,305 -
5.4
No.
537661
5%
5.5
No.
399411
5%
5.6
No.
399411
5%
5.7
Panel Designation:PDB KITCHEN & BASEMENT VENTILATION PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3500 (L) x800 (W) x 2375 (H) Location : Panel Designation:LIFT PDB(-Office and cafetaria ) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):3500 (L) x800 (W) x 2375 (H) Location : Panel Designation:UTILITY PUMP MCC Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 2 of 3 - R6 & Panel annexure-1 Location : Chiller Room
No.
413411
5%
5.8
20,671 -
No.
320661
5%
5.9
No.
619911
5%
16,033 30,996 -
5.10 Panel Designation :PCC For Load Centre-2(HEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 6500 (L) x1500 (W) x 2375 (H) Location : Load Centre-2 5.11 Panel Designation: PCC For Load Centre-3(LEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ): 6500 (L) x1500 (W) x 2375 (H) Location : Load Centre-2 5.12 Panel Designation:675kVAR-RT- APFC Panel at Factory Load Centre 2&3 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 Panel annexure-1 Approx.Overall dimension ( in mm ): 4000 (L) x800 (W) x 2375 (H) Location : Load Centre-2&3 Note: The APFC Relay shall be intelligent microprocessor type with serial communication port suitable for minimum 12 stages & 2 relays shall be considered in each APFC Panel 5.13 Panel Designation: MLDB-1 - for Factory Building (LEB) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 Panel annexure-1 Approx.Overall dimension ( in mm ):1800 (L) x450 (W) x 2025 (H) Location : Load Centre-3 5.14 Panel Designation: MLDB-2 - for Factory Building (HEB) R6 &
No.
3504100
5%
175,205 -
No.
3191116
5%
159,556 -
2 RS 485 Sets of
No.
1979581
5%
98,979 -
R6 &
1 No. 471161
5%
23,558 -
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation 1 No. 534161
5%
Remark
Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):1800 (L) x450 (W) x 2025 (H) Location : Load Centre-2 5.15 Panel Designation:HVAC &OTHER UTILITIES PDB -1 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):4500 (L) x800 (W) x 2375 (H) Location : Load Centre-2 5.16 Panel Designation:HVAC &OTHER UTILITIES PDB -2 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):4500 (L) x800 (W) x 2375 (H) Location : Load Centre-3
560,869 1,137,817 815,931 377,119 266,869 226,444 213,582 169,491 437,757 432,244 1,800 CAPEX ITEM-Offer from GE attached 750 CAPEX ITEM-Offer from GE attached 3,000 CAPEX ITEM-Offer from GE attached 2,000 CAPEX ITEM-Offer from GE attached 2,000 CAPEX ITEM-Offer from GE attached 1,500 CAPEX ITEM-Offer from GE attached 1,500 CAPEX ITEM-Offer from GE attached 3,500 CAPEX ITEM-Offer from GE attached 4,500 CAPEX ITEM-Offer from GE attached 4,000 CAPEX ITEM-Offer from GE attached
26,708 -
No.
1083635
5%
54,182 -
No.
777077
5%
5.17 Panel Designation: PDB -LOAD CENTER-2 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Load Centre-3 5.18 Panel Designation: PDB -LOAD CENTER -3 Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2700 (L) x800 (W) x 2375 (H) Location : Load Centre3
38,854 -
No.
359161
5%
17,958 -
No.
254161
5%
5.19 Panel Designation : -3 -Phase 32 Amp -SOCKET OUTLET PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155012 - R0 & annexure-1 Approx.Overall dimension ( in mm ):2400 (L) x800 (W) x 2375 (H) Location : HEB & LEB FACTORY SHED 5.20 Panel Designation : -1- Phase 20 Amp -SOCKET OUTLET PDB Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155012 - R0 & annexure-1 Approx.Overall dimension ( in mm ):2400 (L) x800 (W) x 2375 (H) Location : HEB & LEB FACTORY SHED 5.21
12,708 -
Panel
No.
215661
5%
10,783 -
Panel
No.
203411
5%
10,171 -
Panel Designation :UPS Input D.B. 2X60 k.V.A-FACTORY EMERGENCY LIGHTING Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155008 - R0 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : Load Center-3 Panel Designation :UPS Output D.B. 2X60 k.V.A-FACTORY EMERGENCY LIGHTING Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155008 - R0 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : Load Center-3
No.
161420
5%
8,071 -
5.22
1 1
No. No
416911 411661
5% 5%
5.23 Panel Designation :A.C. D.B- -Utility Building(35k.A. ) Electrical SLD Ref.GE-P-FAC-Ele00-01-11-155000-Sh 3 of 3 - R6 & Panel annexure-1 Approx.Overall dimension ( in mm ):2500 (L) x800 (W) x 2375 (H) Location : MRS Building 6 UPS SYSTEM : Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of following rating UPS with ,15 Min battery backup , with static & manual bypass Input Voltage: 3 Ph 415 Volts, 10% Output : 3 -Phase-415Volts 4w 50 Hz 2% , The scope also includes supply, Installation, Testing and Commissioning with flooded lead-acid batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries & also TVSS at the input of each UPS to protect against transients, surges & Noise as per the tender specifications 80k.V.A. UPS(Factory Office W.S.) Application & suitable for Parallel operation with communication facilities. 60k.V.A. UPS Lighting Application & suitable for Parallel operation with communication facilities. 10k.V.A. UPS for Server application (Independent application) Note :Above UPS system shall be suitable for Parallel operation on Separate Power Distribution Boards. Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of 10 KVATrue- On Line sine wave invertor with ,30 Min battery backup , Input Voltage: 3 Ph 415 Volts, 10% Output : 3 Phase-415Volts 4w 50 Hz 2% , The scope also includes supply, Installation, Testing and Commissioning with flooded lead-acid batteries complete with intercell connectors & copper cables, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. (1No Dedicated invertor for MRS Internal Emergemcy Lighting & 1 No Dedicated for Emergency lighting of Basement of Load center-1 ) TPN -ISOLATORS Supply, Transprtation, storing at site, shifting at work place installation, testing and commissioning of TPN 415 Volts Heavy duty Isolators of following rating, The complete assembly shall be with 2 mm thick CRCA metalic enclosure, Finished paints, IP 65 Degree of protection , Padlock arrangements & Suitable incoming & outgoings cables termination arrangements. 400Amps -TPN
20,846 20,583 -
1,309,875 1,239,000 603,750 17,500 CAPEX ITEM-Offer from GE attached 8,400 CAPEX ITEM-Offer from GE attached 21,000 CAPEX ITEM-Offer from GE attached
62,375 -
6.2 6.3
2 0
Set Set
1180000 575000
5%
59,000 28,750 -
5%
6.4
Set
165000
5%
8,250
173,250
7.1
UR UR
Nos Nos
64,260 61,047
64,260 61,047
4,900 2,100
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor 36,540 36,540 23,940 13,860 13,860 13,860 13,860 Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation 36,540 36,540 23,940 13,860 13,860 13,860 13,860 1,400 1,400 1,120 980 840 840 840 Remark
315Amps -TPN 250Amps -TPN 200mps -TPN 125Amps -TPN 100Amps -TPN 63Amps -TPN UP TO 32Amps -TPN TOTAL OF SECTION B-SUBSTATION EQUIPMENTS
UR UR UR UR 6 36 26
C 1
SECTION -C -CABLES AND CABLE TERMINATIONS LT CABLES Supply,taking delivery at site, unloading at site,Installation,testing & commisioning of XLPE Insulated, PVC sheathed, armoured, 650/ 1100 V grade power and control cables to be laid in trenches, on cable trays, burried in ground. Civil work for cables to be laid burried in ground such as excavation, backfilling, sand and brick protection and cable tray /tray supports are measured separately and Miscellaneous items such as saddles, clamps, cleats, cable tags/ cable markers etc. are included in the scope 400 8000 1100 1400 1800 300 1000 1300 1350 1250 300 900 3700 UR UR UR UR UR 25000 1000 15500 450 600 1800 3000 200 UR UR 125 125 UR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR MTR 1,150 802 659 520 428 360 285 232 166 128 105 105 124 146 110 90 243 78 86 80 316 202 146 95 70 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 115 80 66 52 43 36 29 23 17 13 11 11 12 15 11 9 24 8 9 8 32 20 15 10 7 36 36 1,265 882 725 572 471 396 314 255 183 141 116 116 136 161 121 99 267 86 95 88 348 222 161 105 77 396 399 120 100 100 80 80 70 70 60 60 50 50
1.1
1.1.1 3.5.C x 400 Sq.mm. A2XFY(XLPE- AL-Armoured) 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9 1.1.10 1.1.11 1.1.12 1.1.13 1.1.14 1.1.15 1.1.16 1.1.17 1.1.18 1.1.19 1.1.20 1.1.21 1.1.22 1.1.23 1.1.24 1.1.25 1.1.26 1.1.27 1.1.28 1.1.29 1.1.30 1.1.31 2 2.1 3.5.C x 300 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 240 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 185 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 150 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 120 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 95 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 70 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 2C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 4C x 25 Sq.mm.A2XFY(XLPE- AL-Armoured) 3C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3CX10Sq.mm. XFY(XLPE -CU-Armoured) 3CX4Sq.mm. XFY(XLPE -CU-Armoured) 3CX2.5 Sq.mm. XFY(XLPE -CU-Armoured) 4CX16Sq.mm. A2XFY(XLPE- AL-Armoured) 4CX10Sq.mm. A2XFY(XLPE- AL-Armoured) 4CX10Sq.mm. XFY(XLPE -CU-Armoured) 4CX6 Sq.mm.XFY(XLPE -CU-Armoured) 4CX4Sq.mm. XFY(XLPE -CU-Armoured) 4CX2.5Sq.mm. XFY(XLPE -CU-Armoured) 4CX1.5Sq.mm. YWY(PVC -CU-Armoured) 2CX10Sq.mm. XFY(XLPE -CU-Armoured) 2CX4Sq.mm. XFY(XLPE -CU-Armoured) 19CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 24CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 5CX2.5 Sq.mm. WY(PVC -CU-Un-Armoured Flexible ) LT cable Terminations : LT cable Termination : Supply & installation of Termination of XLPE insulated, PVC sheathed, 650/1100 V grade, armoured cable including stripping of cable insulation, supplying and fixing of Aluminum / tinned plated copper lugs and crimping the same to the conductor, supply and fixing of double compression cable glands including all 'labour supply and consumable material required for jointing / termination. 3.5.C x 400 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 300 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 240 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 185 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 150 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 120 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 95 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 70 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5.C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3.5C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 2C x 25 Sq.mm.A2XFY(XLPE- AL-Armoured) 3.5C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 4C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 50 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 35 Sq.mm. A2XFY(XLPE- AL-Armoured) 3C x 25 Sq.mm. A2XFY(XLPE- AL-Armoured) 3CX10Sq.mm. XFY(XLPE -CU-Armoured) 3CX4Sq.mm. XFY(XLPE -CU-Armoured) 3CX2.5 Sq.mm. XFY(XLPE -CU-Armoured) 4CX16Sq.mm. XFY(XLPE -CU-Armoured) 4CX10Sq.mm. XFY(XLPE -CU-Armoured)) 4CX10Sq.mm. XFY(XLPE -CU-Armoured) 4CX6 Sq.mm. XFY(XLPE -CU-Armoured) 4CX4Sq.mm. XFY(XLPE -CU-Armoured) 4CX2.5Sq.mm. XFY(XLPE -CU-Armoured) 4CX1.5Sq.mm. YWY(PVC -CU-Armoured) 2CX10Sq.mm. XFY(XLPE -CU-Armoured) 2CX4Sq.mm. XFY(XLPE -CU-Armoured) 19CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 24CX1.5Sq.mm. YWY(PVC -Cu-Armoured) 5CX2.5 Sq.mm. WY(PVC -CU-Un-Armoured Flexible ) Note: Aluminum Lugs shall be used for AlLUMINUM Conductor Cables & Copper Lugs for COPPER Cables TOTAL OF SECTION C- CABLES SECTION -D-CABLE TRAYS & ASSOCIATED WORKS
35 30 30 30 25 25 25
360 363
70 80 25
2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 2.1.8 2.1.9 2.1.10 2.1.11 2.1.12 2.1.13 2.1.14 2.1.15 2.1.16 2.1.17 2.1.18 2.1.19 2.1.20 2.1.21 2.1.22 2.1.23 2.1.24 2.1.25 2.1.26 2.1.27 2.1.28 2.1.29 2.1.30 2.1.31
36 32 14 20 6 2 8 22 16 14 4 14 46 UR UR UR UR UR 2000 40 550 30 40 70 60 20 UR UR 30 24 UR
No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No
2,977 2,643 2,570 1,658 1,649 1,114 940 835 679 600 395 395 401
461 721
2,977 2,643 2,570 1,658 1,649 1,114 940 835 679 600 395 395 401
350 300 300 250 250 200 200 180 180 120 120 150 120 120 100 60 80 100 100 60 60 60 60 60 40 40
461 721
100 150 35
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
Supply and fixing of followings sizes pre galvanized factory fabricated GI Ladder type cable tays, including straight runs, bends, reducers, Tees, cross members ,couplings, earth continuity flexible conductor for each joints,anchor fastners, supports,drilling,cuttings,nuts, bolts, required civil works etc to complet the work. The required MS support shall be measured under M.S. steel BOQ item no-------------------------750 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 600 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 450 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 300 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 100 mm wide Runners 20 x 75 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C 50 Mtr. 610 10% 2000 Mtr. 555 10% 100 Mtr. 495 10% 50 Mtr. 435 10% UR Mtr. 360 10% 36 44 50 56 61 671 611 545 479 396 200 Offer from profab is attached
1.1
1.2
1.3
1.4 1.5
1.6
Supply and fixing of perforated type GI cable trays of the following sizes as per specification. UR 750 mm x 75 x 75 x 2 mm thick 1200 600 mm x 75 x 75 x 2 mm thick 300 450 mm x 75x 75 x 2 mm thick 800 300 mm x 75x 75 x 2 mm thick 600 150 mm x 50 x 50 x 2 mm thick Supply and fixing of GI cable trays covers of 2 mm thick including all necessary fixing arrangement,hardware, consumable etc . Suit to following GI perforated and ladder type cable trays . 750 600 450 300 150 mm mm mm mm mm x 75 x 75 x 2 mm x 75 x 75 x 2 mm x 40 x 40 x 2 mm x 40 x 40 x 2 mm x 25 x 25 x 2 mm thick thick thick thick thick UR 50 UR UR UR
100 83 67 50 28
Offer from Offer from Offer from Offer from Offer from
profab is attached profab is attached profab is attached profab is attached profab is attached
74 60 46 31 17
Offer from Offer from Offer from Offer from Offer from
profab is attached profab is attached profab is attached profab is attached profab is attached
Supply, Installation,testing & Commissioning, of MS Powder Coated with RAL 7032 Race Ways ,for fixing high bay light fitting at10 to 12 M. from finished floor leve,. fabricated out of 14 gauge MS CRC sheet to form C type channel raceway with cover on side(Screw Fixed Type) of size 4000 100x50x50 to be suspended with rods / sleek guyrope / clutch wire from true ceiling /roof for mounting of tube light fitiings. All supporting membere shall be equvillant to GRIPPLE OR PROFAB Make supporitng members/ structures.. Supply, fabrication and installation of cable tray cable tray supports, supports for cable trench covers, supporting frame for mounting of control panels, supports for mounting of local control station,Main Electrical Panel,lighting panel, lighting fixture etc. with 2 coats of enemel primer and 2 coats of epoxy paint Note - The rates shall be inclusive of grouting of supports , Anchor fastner,welding rods, nut,bolts,clamps,and any other consumable which required to complete the works. TOTAL OF SECTION D- CABLE TRAYS SECTION -E-EARTHING Supplying and laying of G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by welding overlapping ) UR 75 mm x 10 mm 9000 50 mm x 10 mm UR 25 mm x 6 mm 7500 25 mm x 3 mm (For street light & power socket earthing) 25 mm x6 mm (Cu) with Brazing joint (For metering Kiosk & Transformer 300 neutral) 50 50 mm x6 mm (Cu) with Brazing joint 500 8 SWG GI wire UR 14 SWG GI wire 200 12 SWG GI wire G.I.earthing bus, 750mm Long x 50x10mm with supporting insulators & all 200 Hardwares Tin plated CU.earthing bus, 750mm Long x 50x6mm with supporting 80 insulators & all Hardwares UR Lightning air terminal 25 mm dia copper rod 1500 mm Long 1core x70 Sq.mm cu cable ,green colour with yellow strip FRLS PVC 1200 insulation (For UPS, L.E.B m/c, CNC m/c & Welding m/c earthing) Providing earthing stations at locations as called for including providing and laying 3 Mtr Long x 65mmDia G.I. electrode with 50 x 6 mm thick G.I. strip, To form earth electrode with inspection chamber,Watering funnel with 20 gauge G I wire ,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines /Boaring, Charcoal, salt, or Bentonie slurry etc) For MSDCL Metering Kiosk.
Mtr
400
10%
400
35
MT
63,000
63,000
1 1.1 1.2 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.12 1.13
Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Mtr. Nos. Nos. No. Mtr.
85 49 14 21
21 Offer from subcontractor is atatched 21 7 11 8 Offer from Offer from Offer from Offer from subcontractor is atatched subcontractor is atatched subcontractor is atatched subcontractor is atatched
100 Offer from subcontractor is atatched 100 Offer from subcontractor is atatched 100 Offer from subcontractor is atatched 35 Offer from subcontractor is atatched
18
No
8,500
10%
850
9,500
Supply,Installation,Testing and commissioning of earth pit of size 600 x 600 x 3 mm copper plate with GI water pipe 2.7 mtr long x19mm dia , buried in earth pit with charcoal and salt each in alternative layers including excavation re-filling etc. all as per enclosed drawing, with C.I.legend identification marker.The complete earth pit shall be as per IS 3043. The scope also includes with inspection chamber,Watering funnel with 20 gauge G I wire ,,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines , Charcoal, salt, or Bentonie slurry etc) (For UPS,Transformer & DG Neutral earthing)
22
No
11,000
10%
1,100
9,500
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
Supply, testing and commissioning earthing stations as per IS 3043, maintenance free earthing pit of mild steel hot dep galvanised. The pipe shall be insterted one inside the another. The pipe shall be filled & packed with highly conductive and anti corrosive mixture with following diamension. The scope also includes with inspection chamber,Watering funnel with 20 gauge G I wire ,600 x600 mm heavy duty Chamber with CI Manhole cover etc.(Scope including excavation by manual/Machines /Boaring, . Length - 3000mm Outer Pipe Dia - 76mm Inner Pipe Dia. - 38mm 300 X 150mm chamber shall be provided for inspection and connection. 50mmx6 mm thick copper strip shall be nut bolted to connect the earthing strips/Leads The electrode shall be provided with two chemical compound bags (20Kg each) Make : Ashlok,Fast Track, JEF
8,150
10%
815
9,500
84
No
LIGHTNING PROTECTION SYSTEM Supply & Installation of ESE Lightning Rod , with Stainless Steel Body, working on the Principle of (ESE) Early Streamer Emission technology, which will offer LEVEL 1 protection for 79 Mtrs radius when mounted at a height of 5 mtrs from the plane to be protected, complying to NFC 17 102. Type- Early Streamer Emission Make & Model - CIRPROTEC (NIMBUS) Matrerial Used - Corrosion resistant stainless steel body Construction Details => The electronic circuit of the ESE rod shall be encapsulated in an epoxy mould to avoid derating or degradation due to atmospheric conditions. This also makes the Lightning rod weather proof and suitable for installation in highly corrosive atmosphere.The rods shall be made of Corrosion Resistant Stainless body conforming AISI 316 grade. The Lightning rod shall be self powered type and shall not require any form of external power supply/batteries for its operation. . Conformity to standards - As per NF C17-102 and UNE 21186-96 Radius of Protection(M) - 79M level 1 Construction Details - Lightning Rods shall be manufactured according to UNE 21.186-96 and NF C17-102 standards . Sensors-Type - Electronic equipped with triggering device Test Reports -Should have been tested at an internationally accredited Laboratory and CPRI , Bangalore and the necessary test reports to be attached. Shall be designed to check the integerity of the electronics periodically with a tester 4 DIGIT ELECTROMECHANICAL Lightning Transient Event counter ,in a IN WEATHER PROOF ENCLOSURE shall be mounted in 1.5 Mtrs from the ground level Each lightning protection set shall be comprising with followings devices
5.1
Set
112,300
10%
11,230
123,530
Main Lightning Air terminal suitable for protection of Radious of 80 meter from its base of 5 Meter height for Level III Protection. GI Elevation pole with a reducer to fix the LA unit, Base Plate, Clamps and all required fixing accessories ( Ready to Install). Test Clamp to connect the down conductor to the earth termination and disconnect the down conductor from the earth termination for regular checks of the earth termination resistance value. 1 Set of Remote Control unit required only for testing the Prevectron air terminal. Lightning Flash Counter. Electronically controlled, register every strike between 1000 A to 100 KA for a 8/20 microsecond peak current. Tested in High Voltage Laboratory (CPRI). TOTAL OF SECTION- E- EARTHING (GROUNDING)
5.2
Nos.
14000
10%
1,400
15,400
F 1
1.1
SECTION F D.G.SETS DIESEL GENERATOR SET Supply Transporation, Unloading at Place of installations,, installation, testing and commissioning of radiator cooled 1000 KVA prime (actual) rating diesel generating set (11000 Volts Alternator with PCCM or equivalent) along with day oil fuel tank, CT Adaptor Box, AVM Pads including cable termination box with all associated equipment / work as per specifications. Alternator shall have class H insulation 11000 Volts and rated for 800 KW output. Engine shall not be derated upto 50 deg.C ambient and suitable for bearing the starting current after changeover. The scope also includes providing foundation details drawings to Engineer In Charge (Foundation will be provided by Civil scope of works), Liasioning work from Govt Authorities Like Electrcial Inspector, MIDC, Pollution control Boards etc. The scope also includes filling first oil ,fuel for commissioning. Supply, installation, testing and commissioning of powder coated acoustic enclosure suitable for 1000 KVA DG set for indoor application as per specification complete with all accessories as required including ventilation system. No deration in DG set capacity shall be accepted on this account. The scope also includes providing foundation details drawings to Engineer In Charge (Foundation will be provided by Civil scope of works), Liasioning work from Govt Authorities Like Electrcial Inspector, MIDC, Pollution control Boards etc. Supply, erection, testing and commissioning of exhaust piping Min. 6mm Thick of following sizes with welding joint including bends, MS pipe supports, clamps, dash fastener, nuts, bolts etc.,with first layer of insulation 25mm thick ceramic fiber wool (96Kg/Cub. Mtr.) & second layer minimum 50mm thick rockwooll (150Kg/Cub Mtr.) covered with 26 SWG aluminium sheet claddings etc. complete as required and as per specifications.
Nos
9,000,000
9,000,000
30,000
1.2
Nos
1,000,000
1,000,000
10,000
1.3
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor 8,800 6,550 Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation 8,800 6,550 2,500 2,000 Remark NON GE CAPEX ITEM- OFFER FROM POWERICA IS ATTACHED
a b
55 35
Mtrs Mtrs
1.4
Exhaust pipe supporting system with M.S channel, M.S angle, M.S flat, dash fastners, nut, bolt etc. complete including 1 coat of redoxide & 2 coat of 5000 enamel paint and other Accessories as required at the site of work.
K.G.
85
85
25
1.5 a b c d e f
ELECTRICAL PLC / SCADA Application Interface cables Supply & Installation( PVC Screened Copper cables) 24C x 1.5 Sq.mm PVC screened cable 8C x 1.5 Sq.mm PVC screened cable 4C x 1.5 Sq.mm PVC screened cable ( For Electronic Governer ) 12 C x 0.5 Sq.mm PVC screened Triad cable ( for temperature scanner ) Profi bus 2 wire Communication cable
56 42 35 42 42
1.6
Supply, installation, testing and commissioning of D.G Set Automatic Synchronizing panel suitable for,11k.V.26.2k.A. ,2 x 1000k.V.A. D.G. Set as per Technical specification & enclosed Single line diagram ( Drg. No GE-PFAC-Ele00-01-08-155003 ) The Specification for D.G. Autosynchronizing Panel shall be as per HT Panel items reference sr 1 of section B
Set
4,200,000
4,200,000
12,000
1.7
Supply, installation, testing and commissioning of NEUTRAL GROUNDING RESISTOR (NGR) panel suitable for Each D.G. Set of 1000k.V.A. as per Technical specification & enclosed Single line diagram ( Drg. No GE-P-FACEle00-01-08-155003 ) The Complete NGR Panels shall be comprising followings parameters. NGR Element : Resistance: 121Ohms & 52.48 Amps at 11/ 3 k.V. 1 No 400Amp-12k.V. Single Pole Vacumm contactor with Auxiliary contacts 3 Nos 75/1Amp CL -PS CT with internal wiring & terminals IP Degree of complete NGRVPanel : IP65 TOTAL OF SECTION- F- GENERATOR SET SECTION -G-LIGHTING FIXTURES/EXHAUST FANS Supply, installation, testing and commissioning of luminaires complete with, lamps, ballast, starter, HPF condenser, standard down rod, connecting cord, The rate shall include all necessary fixing accessories like MS hooks, MS supports, fasteners, with all necessary hardware, accessories as required for complete installation. Quoted rate shall exclude the cost of earthing . Note: Catalogue numbers indicated are only to describe type of light fixture required. Lamp Colour shall be - 84 or as approved by Architect / Consultant. Supply Installation, testing & commissioning of 2x28 W T5 with electronic ballast equivallent to GE cat no GET CI 2X28 C/S HF.The scope also includes all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X1.6 mm thick G.I. steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core wires and earthing , fastening accessores etc as required to complete the work 4X54W T5 Highdbay Luminaire Equivallent to GE Cat Ref ELC454 with Lamps of 4 X54W FTL T5 with dimmable choke suit for dimming control, on M.S. raceway mouted on 12-14 Meter elevation including arrangement of all cherry pickers, loopings of 3 core 1.5 Sq.mm Flexible FRLS insulated cables from looping junction boxe to each fitting NOTE.:- Race will supply 7 instaalation will be measured separetly. (No welding will allowed) 2 Nos 225,000 225,000 5,000 Rate from Market as panel is fabricated
1.1
50
Nos
1200
5%
60
1,260
1.2
875
Nos
4650
5%
233
4,883
1.4
95 W LED IP 66 Street light fixture to fixed on 7.5 to 9 Meter hight poles including supply and pulling of 3 Core x 1.5 Sq..mm Cu Flexible ,-FRLS cables from Pole mouted looping junction box to each fitting terminals 150W HPMV Integral Post top light fixture equivallent to GE cat no DUNAADCMH150W TU including supply and pulling of 3 Core x 1.5 Sq..mm Cu Flexible ,-FRLS cables from concealed looping junction box to each fitting terminals, including providing concealed 25 mm PVC pipes for incoming cables to Looping junction box & up to each light fittings,
176
Nos
3150
158 -
1.5
Nos
7200
360
7,560
42 W LED Recess mounted decorative luminaries equivallent to GE cat no GCRO42.56 MO with all accessories and tube etc., including supplying and fixing ball and socket arrangement 2 nos /Flexible SS Chains/ or 2 no. down rods of 20 mm dia X1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 3 Corex 1.5 sq. mm FRLS insulated, copper conductor, cable and earthing etc as required. 2X28W FTL T5 Surface Mounted with clear Acrylic cover Luminaire with electronic ballast equivallent to Wipro cat no WCF 50228 SGW including required clamps , fastners ,connection to fittings etc to fixed in staircase etc. 2 x18 W Decorative Recess mounted Down lighter equivallent to GE cat no GECFLC2X36DNLR(H) HF with required hanging support from ceiling 1 x18 W Decorative Recess mounted Down lighter equivallent to GE cat no GECFLC2X18DNLR(H) HF with required hanging support from ceiling
1.6
Nos
2200
5%
110
2,310
1.7 10 Nos 1350 5% 1.8 0 Nos 1150 5% 1.9 0 Nos 3650 5% 183 150 W MH Integral Flood light Luminaire Equivallent to GE cat no 1.10 GEMF1X150CAI with required support to fixed on top plate of 7.5 Mtr high street light pole 8 Nos 5200 5% 260 58 68
1,418 1,208 3,833 5,460 245 CAPEX ITEM-Offer from GE is attached 140 CAPEX ITEM-Offer from GE is attached 210 CAPEX ITEM-Offer from GE is attached 210 CAPEX ITEM-Offer from GE is attached
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Note for above light fittings items i All light fittings quantities shall be procured as per Final approved Drawings by architect & approval from client /Architects for sample of each light fittings. Connection of lighting fixtures from ceiling rose / junction box by flexible copper wires in flexible conduit/M.S. ball and socket arraqngment is included in the conduit down rod, scope The structural supports for suspension of lighting fixtures are measured seperately Supply,& Installation of Exhaust fans of following ratings Supply, of Exhaust fan Heavy duty 230 V AC 50 Hz 305 mm 1400 RPM with condenser complete erected in position with n/c materials Fan motor with moisture treatment and class E insulation & With bird protective screen Supplying of capacitor type1200 mm sweep ceiling fan complete with down rod, blades, shakle etc. with high breeze, high speed for operation on 230V, 50 Cy. Single phase A.C. supply confirming to IS 374-1979 and with double ball bearing system The fan shall be green rated as per BEE norms. Supply of 750 mm sweep-1 Ph 240 Volts 50 Hz Wall/Column Mounted Air cirulated fans including Inbuilt speed regulator Including all necessary fixing hardware,Anchor fastner etc. Almonard make Supply & Fixing of Ceiling mounted (surface/flush) high performance, Movement Detector with the coverage of 6Mtrs dia complete with necessary Sensor control wiring.vWIPRO Cat ref COP 11010 OR Hager make EE805 or Schneider make CSS54E-WE or Bajaj Make - BajajLeviton OSC 10-MOW TOTAL OF SECTION G- LIGHTING LUMINARIES H 1 SECTION :H: SUPPLY & PROVIDING OF POINT WIRING AND ACCESSORIES. POINT WIRING -IN M.S. CONDUITS Primary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 2 Nos 2.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG black stove enemelled steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Primary light point up to 5 meter length Primary light point up to 8 meter length Primary light point up to 10meter length Secondary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 3 Nos 1.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Secondary light point up to 2 meter length Secondary light point up to 4 meter length Secondary light point up to 5meter length Secondary point Wiring for twin control light point with 1.5 sq.mm FR LS insulated copper conductor single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR LS insulated copper conductor single core cable etc as required. Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface / recessed 25 mm dia, 16 SWG Black stove enemelled steel conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Power plug wiring in M.S. Black stove condiut (2 x 4 sq.mm) - Wiring for power plug with 2X4 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25 mm dia M.S. Black stove conduit along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in M.S. Black stove condiut (2 x 2.5 sq.mm) - Wiring for power plug with 2X2.5 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25mm dia,M.S. Black stove conduit along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in M.S. condiut (4 x 4 sq.mm )- Wiring for powersocket outlet with 4X4 sq. mm. FRLS insulated, copper conductor, single core cable in surface/recessed 16SWG ,25 mm. dia M.S. black stoved enemelled conduit along with 2 nos. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. POINT WIRING -IN PVC CONDUITS 25 20 20 Point Point Point 355 547 693 355 547 693 150 175 200 Offer from subcontractor is attached 10 20 20 Point Point Point 806 1,151 1,424 806 1,151 1,424 175 200 225 Offer from subcontractor is attached Remark
400 W MH Integral Flood light Luminaire Equivallent to GE cat no ZF400 1.11 KRC .The fitting shall be installed on top mounting plate of 16 Mtr high lighting mask.
UR
Nos
ii iii 2
2.1
30
No
6,930
6,930
2.2
Nos
1,890
1,890
2.3
80
Nos
10,080
10,080
2.4
Nos.
7,560
7,560
1.1
a b c
1.2
a b c
1.3
UR
Point
1,424
1,424
1.4 a b c
0 0 0
25 35 40
1.5
Mtr
475
475
1.6
Mtr
437
437
1.7
Mtr
516
516
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
2.1
Primary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 2 Nos 2.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Primary light point up to 5 meter length Primary light point up to 8 meter length Primary light point up to 10meter length Secondary light Wiring for followings light point/ fan point/ exhaust fan point/ call bell point with 3 Nos 1.5 sq.mm FRLS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS insulated copper conductor single core cable etc as required. (Wiring from Lighting Switch boards to first light points in the group of lighting circuit ) Secondary light point up to 3 meter length Secondary light point up to 5 meter length Secondary light point up to 8meter length Secondary point Wiring for twin control light point with 1.5 sq.mm FR LS insulated copper conductor single core cable in surface / recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR LS insulated copper conductor single core cable etc as required. Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Power plug wiring in PVC condiut (2 x 4 sq.mm) - Wiring for power plug with 2X4 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in PVC condiut (2 x 2.5 sq.mm) - Wiring for power plug with 2X2.5 sq. mm., FR LS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Power plug wiring in PVC condiutt (4 x 4 sq.mm )- Wiring for powersocket outlet with 4X4 sq. mm. FRLS insulated, copper conductor, single core cable in surface/recessed Heavy duty 2 mm in thick & 25 mm diameter PVC conduit along with 2 nos. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. Wiring Accessores for Raw power & UPS Power socket outlets S/F GI Box along with modular plate: Supplying and fixing following size /modules, GI box along with modular base & cover plate for modular switches in recess etc as required. The scope also includes cutting of wall, block works, & POP of walls with mesh after plate fixing & other related civil works to make surface good . 1 or 2 Module(75mmx75mm) 3 Module (100mmX75mm) 4 Module (125mmX75mm) 6 Module (200mmX75mm) 8 Module (125mmX125mm) 12 Module (200mmX150mm) Supply & fixing following modular base and cover plate for modular switches in recess etc as required. 1 or 2 Module 3 Module 4 Module 6 Module 8 Module 12 Module Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Raw Power /UPS Power socket outlets) 5/6 amps switch 15/16 amp switch 3 pin 5/6 amp socket outlet 6 pin 15/16 amp socket outlet 0 0 0 Point Point Point 280 542 867 280 542 867 125 160 175 Offer from subcontractor is attached 0 0 0 Point Point Point 806 1,151 1,424 806 1,151 1,424 150 175 200 Offer from subcontractor is attached
a b c
2.2
a b c
2.3
UR
Poit
1,273
1,273
2.4 a b c
0 0 0
15 20 25
2.5
Mtr
273
273
2.6
Mtr
248
248
2.7
UR
Mtr
1,084
1,084
3.1
a b c d e f 3.2 a b c d e f
UR UR UR UR UR UR
No No No No No No
25 25 30 35 35 50
UR UR UR UR UR UR
No No No No No No
25 25 30 35 35 50
3.3 a b c d
UR UR UR UR
No No No No
25 25 35 40
3.4
Supply and providing of Power plug wiring in Raceway in office (2 x 4 sq.mm) - Wiring for light/power plug with 2X4 sq. mm. , FR LS insulated, copper conductor, single core cable in existing surface/recessed raceway along with 1 no. 4sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. (UPS & Raw Power Power)
UR
Mtr
122
122
3.5
Supply and providing of Power plug wiring in Raceway in office (2 x 2.5 sq.mm) - Wiring for light/power plug with 2X4 sq. mm. , FR LS insulated, copper conductor, single core cable in existing surface/recessed raceway along with 1 no. 2.5sq.mm., FR LS insulated, copper conductor single core cable for loop earthing as required. (UPS & Raw Power Power)
UR
Mtr
110
110
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
Supply, fixing, laying and embedding in UNDER FLOOR ALUMINUM of following sizes complete with all accessories including junction box with 2 mm thick Stainless steel cover plate,neoprene gasket in joints ,cutting the floor and jamming the raceway with all necessary hardware (including civil works) as required. 50 x 38 x 2 mm 100 x 38 x 2 mm 150 x 38 x 2 mm 200 x 38 x 2 mm 300 x 38 x 2 mm Supply, fixing, commissioning of following sizes access outlet with all accessories, cutting the floor and jamming the access outlet with all ncessary hardware (including civil works) as required. 250x250x60- 75 mm three compartment. 265x265x53- 80 mm three compartment. Supply , fixing, commissioning of following sizes cross over/ junction box with 3 mm thick cover plate with all accessories cutting the floor and jamming the junction box with all necessary hardware including civil works as required. 250x250x60- 75 mm three compartment. 300x300x60- 80 mm three compartment. UR UR UR UR UR Mtr Mtr Mtr Mtr Mtr 266 411 696 785 1,081 266 411 696 785 1,081 40 60 95 125 130
a b c d e 5
a b
UR UR UR
1,512 1,512 -
1,512 1,512 -
6 a b
UR UR
Nos Nos
3,150 3,150
3,150 3,150
SECTION -I-LIGHTING PANELS-IP42 - & INDUSTRIAL SWITCH SOCKET OUTLET/ISOLATORS Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR LS insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. Typical Raw Power & UPS Power Final D.B. Application (Ref Tender drawing no GE-P-FAC-Ele00-01-11-1550013) Incomer : 63 A,4 pole, MCB 10k.A. C-CL Outgoing :As under 16 - 25A-2P-RCBO 30m.A.:15 Nos (5 Nos/Phase) Typical Lighting D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-111550011) Incomer : 63 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 36 Nos(12 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:36 Nos(12 Nos Per Phase) Typical Lighting D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-111550011) Incomer : 63 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 18 Nos(6 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:18 Nos(6 Nos Per Phase) Typical E. L. D.B. (Ref Tender drawing no GE-P-FAC-Ele00-01-111550010) Incomer : 25 A,4 pole, MCB 10k.A. C-CL+Auto /Manual Control selector switch for outgoing circuits Outgoing :As under 16-25 Amp 2 P Moduler Power contactor with Auxiliary contact for Remote ON /OFF of contactor from BMS & ON/OFF status of contactor to BMS : 12 Nos(4 Nos Per Phase) 16 - 25A-2P-RCBO 30m.A.:12 Nos(4 Nos Per Phase)
1.1
20
No
65,000
65,000
1.2 (a) (b) i ii 1.3 (a) (b) i ii 1.4 (a) (b) i ii 1.5
12
Nos
50,000
50,000
Nos
35,000
35,000
15
Nos
32,000
32,000
Area Street light Final D.B. for Street Lights as under 2 Incomer : 125 Amp -4 Pole MCCB + 1 No 4 Pole-110 Amp Moduler Contractor Outgoing 12 Nos 32 Amp TP MCB 10K.A. CL + 32Amp 4 Pole ELCB -30m.A. per Outgoings& 24 Hrs Timer + Photo Cell with Manual / Auto Selctor switch, Interface provision with BMS & its control wiring etc. Flood Light Mast lighting PDB.as under 1 Incomer : 100 Amp -4 Pole MCCB , + 1No4 Pole-110 Amp Moduler Contractor + 24 Hrs Timer + Photo Cell with Manual / Auto Selctor switch, Interface provision with BMS & its control wiring etc. Outgoing 10 Nos 32Amp 25k.A. TP-MCCB-LS -Release. D.B. Server system Incomer : 63 A,DP,MCB type Isolator Outgoing : 25 A DPMCB- 10k.A -D-CL10 Nos per Phase Security Kiosk D.B. as under Incomer : 63 A,4 pole, MCB 10k.A. C-CL +4 Pole 63 Amp ELCB 100m.A. Outgoing : As under a. 12 Nos 20 A SPMCB- 10k.A -C-CL (4 Nos /Phase) b. 4 Nos 32 A -TP MCB 10k.A. C-CL Supply, Installation, Testing & Commissioning of Following Readymade Industrial Power Sockets with neccessory cable end boxes.The each socket outlet shall be installed at fabricated M.S. Supports/ Frames suit to Sokcet outelt dimensions. The required steel shall be measured under M.S. Fabrication item of this BOQ. 1
No
80,000
80,000
1.6
No
80,000
80,000
1.7
No
15,000
15,000
1.8
No
22,000
22,000
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation Remark
2.1
3 Pin, 20 Amp, 230 Volts Industrial switch socket outlet sheet steel enclosed IP54 with 1 No. earthing terminal 'controlled by -SPN MCB 10K.A C-CL and provided with chain and 'cover and suitable for loop in loop out of 3 x 2.5 'sq.mm XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body. Combine Industrial switch Socket Out Let : 5 Pin 32A, TPN, 415 Volts Industrial switch socket controlled by 4 Pole MCB 10K.A. C-CL & 3 Pin, 20 Amp, 230 V industrial switch socket out let controlled by-SPN MCB 10K.A .-C-CL , sheet steel enclosed indoor type with 2 Nos. earthing terminals and provided with chain & cover suitable 'for loop in loop out of 3.5C x 35 sqmm A2XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body. 5 Pin 63A, TPN, 415 Volts Industrial switch socket controlled by 4 Pole MCB 10K.A. C-CL industrial switch socket out let sheet steel enclosed indoor type IP-54 with 2 Nos. earthing terminals and provided with chain & cover suitable 'for loop in loop out of 3.5C x 35 sqmm A2XFY cable.:The complete assembly shall be suitable for IP65 with Polycarbonate body. METAL MCB BOXES (IP 42) : Supply & fixing of MCB Box enclosed in 1.6mm thick, CRCA sheet steel box. The box shall be concealed / Surface in the wall. The plate cover is properly aligned & flush with the wall surface all materials will be in contractor scope. 20A SP MCB - 01 No. in Metal BOX 20A SP MCB - 02 No. in Metal BOX 20A SP MCB - 03 No. in Metal BOX
100
Set
6,640
6,640
2.2
28
Set
10,630
10,630
2.3
Set
24,774
24,774
25 30 40
75 Rates from GE Price list are taken 75 Rates from GE Price list are taken 75 Rates from GE Price list are taken
TOTAL OF SECTION I- FDB /SSO/LDS SECTION -J-EXTERNAL LIGHTING Supply & installation of hot deep galvanized (internally & externally) Octogonal cross section pole with base plate as per IS 2629 with ,supply and fixing of 2 Nos. of 63 mm dia PVC pipes for cable entry,with inside cable termination,earth connection & with weatherproof door & locking facility 3Nos. 2.5 sq.mm stranded copper flexible wires with MCB control (Minimum Overall Height 8.00 M,3mm thick, bottom dia 200mm,top dia 76 mm,bottom plate 275 mm x 275 mm x 20 mmthick. Including concrate foundation & foundation bolts.(The weather proof Loop In Loop Out junction box with all accessories shall be integral part of street light Poles) Single bracket Double bracket 50 mm dia G.I. bracket mouted street light poles(Max 3 Mtr Length) 183 3 2 No No No 12,500 15,000 10,080 12,500 15,000 10,080 2,500 Market rates considered 700 Market rates considered 700 Market rates considered
1.0
Flood Light Mast As under Supply of 16M high mast shaft in two sections suitable for 39 m/sec wind speed, with raising lowering system comprising, head frame, luminaries carriage suitable to install 8 nos luminaries in symmetrical arrangement, double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightening finial.The scope of works also includes installation including supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. and concreeting including excvation,cement, etc to complete the works.Each lighting mast shall be provided with followings electrical requirement & accessoris. (Note: Contractor to submit required vendor shop drawings for complete Flood light mast system with calculation from structural consultant for foundation before commence of work)
2.1
Set
323,946
323,946
Supply of non-integral floodlight luminaries type Equvillent to GE Cat ref ZF 400KRC with one no. 400 W MH(KRC) T lamps With control gear 2.1.1 boxes The scope also includes Supply and fixing of 3 x 2.5 Sq.mm CuArmoured Cables from each Control gear to each light fittings & its connection with Weather proof D.C. Gland .: 8 Nos to each lighting mast . Supply of single dome aviation obstruction lights of type BJAOL 1 with one nos no. 25 W Neon lamp : 2 Set to each lighting mast & individual Armoured 3x2.5 cu cable connection for the same from its control panel to neon lamp terminals . Supply of out door, Weather proof IP65 Feeder Pillar as per following 2.1.3 specification to each Lighting Mast Incomer:32Amp 4 Pole MCB ,10k.A.,C-Class & 32 Amp 4 Pole ELCB a. 30m.A. +RYB LED Indication+Space Heater with Thermostat. b Outgoing as under b.1 8Nos SP MCB,16Amp,10k.A., B-Class for lighting circuit b.2 2 No 16 Amp DP MCB,10k.A., B-Class forAviation light 1 DOL Feeder for suitable winch motor as per vendor design & with b.3 necessary indication & control system for "LOWER& RAISE" of mast. b.4 16 Amp 10k.A.,B-Class SP MCB controlled 5/15Amp Socket Outlet 2.1.2 TOTAL OF SECTION J- EXTERNAL LIGHTING K 1 SECTION -K -MISCELLANEOUS : Supply,Installation,Testing & commissioning of the following - of the following Supply, Installation, testing and commissioning of start stop local control stations of LM6 material with momentary type PB for stop, start and latch and 1 No. earthing terminal suitable for 4 x 1.5 sq.mm - YWY cable Outdoor, weatherproof type with IP 65 protection Indoor type with IP54 protection Junction box fabricated from 16 SWG sheet steel with screwed gasketed cover and 1 No.earth terminal duly painted with two coats of red oxide and two coats of aluminium paint and to receive 4 Nos. 3 x 2.5 sq.mm YWY cables complete with Elmex terminals. UR UR No. No.
1.1
i ii 1.2
GE INDIA INDUSTRIAL PVT LTD, PUNE RATE ANALYSIS ELECTRICALS WORKS Unit Rate: Rs Sr.No ITEMS DESCRIPTION Qty Unit Quoted rate from vendor 441 Quoted rate from Local Taxes , Fright charges Total Supply subcontractorfor Installation 441 Remark
(Minimum size100mm x 100mm x 75mm) Note : Structural supports for mounting are measured separately 1.3 Floor mounted bucket stand with buckets to hand 4 nos. of 13 ltrs buckets. The stand shall be 5'(L) x 3'(H) x 2"(W) made out of 30 x 300 x 4mm MS angle frame duly coated with 2 coats of red oxide primer & 2 coats of red finish paint Supply and installation of GI pipe class B on wall / steel structure / under floor including bending / treading etc 38 mm dia 50mm dia 75mm dia 100 mm dia 150 mm dia
850
No.
Set
3,000
3,000
UR UR UR UR UR
Supply and installation of 2c x 2.5 sq.mm copper flexible wire Cable Markers as per Std. Drawing H.T. Cable marker L.T. Cable Marker Earthing Tag Marker as per Electrical Inspectorate requirement Saftey Equipmnt Antiskid black rubber mat of approved make,12 mm thick 900mm wide x 1800mm Long chequered type as per IS-5424 in following voltage grade(Jyothi Make)
UR
Mtr.
15 5 103
70 Offer from subcontractor is attached 70 Offer from subcontractor is attached 70 Offer from subcontractor is attached
5.1.1 415 V voltage grade 5.1.2 33 kV voltage grade 5.1.2 11 kV voltage grade 6 7 First Aid box with all the standard contents. First aid chart made of cloth for electricall shock treatment printed in English ,& Hindi duly framed with front glasses. Pair of rubber gloves and gumboots 33 kV grade 11 kV grade Metallic danger boards. 33 kV 11 kV 415 V Portable 5 kg. dry type fire extinguisher suitable for electrical fire and as recommended by the tariff advisory committee. Supply and fixing of the following charts / drawings duly framed with front glass Single line diagram Outdoor lighting and cable layout Supply and installation of RCC hume pipe as under 300 mm dia Half Round Pipe( For Incoming HT cable from Overhead Line to Metering Room)
60 5 30 3
35 Offer from subcontractor is attached 35 Offer from subcontractor is attached 35 Offer from subcontractor is attached 35 Offer from subcontractor is attached
No.
189
189
8 8.1 8.2 9 i i ii 10
1 3
No. No.
600 600
600 600
2 3 3
35 Offer from subcontractor is attached 35 Offer from subcontractor is attached 35 Offer from subcontractor is attached
No.
6,400
6,400
11 i ii 12 12.1
3 2
No. No.
750 750
750 750
105 Offer from subcontractor is attached 105 Offer from subcontractor is attached
15 UR UR
70 Offer from subcontractor is attached 56 Offer from subcontractor is attached 70 Offer from subcontractor is attached
12.2 150mm dia 12.3 300mm dia 13 4 way Flame proof Junction box suitable for installation in hazardous area with IP 65 Protection as per IS 12063/1897 & Gas group IIA & IIB & 1 No.earth terminal inside & 2 terminal outside duly painted with two coats of red oxide and two coats of aluminium paint and to receive 4 Nos. 3 x 2.5 sq.mm YWYcables complete with Elmex terminals. Flame proof Rotary Switches suitable for installation in hazardous area with IP 65 Protection as per IS 12063/1987 & Gas group IIA & IIB & 1 No.earth terminal inside & 2 terminal outside & to receive 3 Nos. 3 x 2.5 sq.mm YWY cables TOTAL OF SECTION K- MISC. L 1 1.1 1.2 1.3 2 3 4 SECTION- L-CIVIL WORKS Excavation & Back filling of cable trenches in following soil conditions Soft soil Murum Hard Rock Supply and laying of sand for cables. Supply and laying of burnt bricks for cables as per standard practice Supply and Spreading of gravel 40mm size, 100 mm thick with duly levelling of Transformer pit TOTAL OF SECTION L- CIVIL WORKS
UR
No
2,520
2,520
14
UR
No
3,150
3,150
Cum Cum Cum CU.Mtr Nos Cu Mtr 2,700 9 3,500 2,700 9 3,500 -
350 Offer from subcontractor is attached 715 Offer from subcontractor is attached 1,750 Offer from subcontractor is attached 700 Offer from subcontractor is attached 2 Offer from subcontractor is attached 300 Offer from subcontractor is attached -