Escolar Documentos
Profissional Documentos
Cultura Documentos
MODULE-43B
Origin of soils, soil classification, three-phase system, fundamental definitions, relationship and interrelationships, _________________________________________________________________________
1. The void ratio and specific gravity of a soil are 0.65 and 2.72 respectively. The degree of saturation (in percent) corresponding to water content of 20% is (A) 65.3 (B) 20.9 (C) 83.7 (D) 54.4
2. The avoid ratios at the densest, loosest and the natural states of a sand deposit are 0.2, 0.6 and 0.4, respectively. The relative density of the deposit is (A) 100% (B) 75% (C) 50% (D) 25% 3. The following data were obtained from a liquid limit lest conducted on a soil sample.
Number of blows Water content (%) 17 68.3 22 63.1 25 61.9 28 60.6 34 60.5
5.
The undrained cohesion of a remoulded clay soil is 10 kN/m2. If the sensitivity of the clay is 20, the corresponding remoulded compressive strength is (a) 5 kN/m2 (b) 10 kN/m2 2 (c) 20 kN/m (d) 200 kN/m2 The ratio of saturated unit weight to dry unit weight of dry unit weight is 1.25. If the specific gravity of solids (Gs) is 2.56, the void ratio of the soil is (a) 0.625 (b) 0.663 (c) 0.944 (d) 1.325 A soil mass contains 40% gravel, 50% sand and 10% silt. This soil can be classified as (a) silty sandy gravel having coefficient of uniformity less than 60. (b) silty gravelly sand having coefficient of uniformity equal to 10. (c) gravelly silty sand having coefficient of uniformity greater than 60. (d) gravelly silty sand and its coefficient of uniformity cannot be determined. A saturated soil mass has a total density 3 22kN/m and a water content of 10%. The bulk density and dry density of this soil are 3 3 (a) 12 kN/m and 20 kN/m respectively. 3 3 (b) 22 kN/m and 20 kN/m respectively. 3 3 (c) 19.8kN/m and19.8 N/m respectively. 3 3 (d) 23.2kN/m and19.8kN/m respectively.
6.
7.
The liquid limit of the soil is (A) 63.1 % (B) 62.8 % (C) 61.9 % (D) 60.6 % 4. Data from a sieve analysis conducted on a given sample of soil showed that 67% of the particles passed through 75 micron IS sieve. The liquid limit and plastic limit of the finer fraction was found to be 45 and 33 percents respectively. The group symbol of the given soil as per IS: 1498-1970 is (A) SC (C) CH (B) MI (D) MH 8.
9.
Sieve analysis on a dry soil sample of mass 1000 g showed that 980 g and 270 g of soil pass through 4.75 mm and 0.075 mm sieve, respectively. The liquid limit and plastic limits of the soil fraction passing through 425 sieves are 40% and 18% respectively. The soil may be classified as (a) SC (b) MI (c) CI (d) SM
JH ACADEMY
Page 1
10. The water content of a saturated soil and the specific gravity of soil solids were found to be 30% and 2.70, respectively. Assuming the unit weight of water to be 10 kN/m3, the saturated unit weight (kN/m3) and the void ratio of the soil are (a) 19.4, 0.81 (b) 18.5, 0.30 (c) 19.4, 0.45 (d) 18.5, 0.45 11. Group symbols assigned to silty sand and clayey sand are respectively (A) SS and CS (B) SM and CS (C) SM and SC (D) MS and CS 12. The liquid limit (LL), plastic limit (PL) and shrinkage limit (SL) of a cohesive soil satisfy the relation (A) LL>PL<SL (B) LL>PL>SL (C) LL<PL<SL (D) LL<PL>SL 13. Deposit with flocculated structure is formed when (A) Clay particles settle on sea bed (B) Clay particles settle on fresh water lake bed (C) Sand particles settle on river bed (D) Sand particles settle on sea bed 14. The laboratory test results of a soil sample are given below: Percentage finer than 4.75 mm = 60 Percentage finer than 0.075 mm = 30 Liquid Limit = 35% Plastic Limit = 27% The soil classification is (A) GM (B) SM (C) GC (D) ML-MI
18. As per the Indian Standard soil classification system, a sample of silty clay with liquid limit of 40% and plasticity index of 28% is classified as (A) CH (B) CI (C) CL (D) CL-ML 19. In its natural condition, a soil sample has a mass of 1.980 and a volume of 0.001 . After being completely dried in an oven, the mass of the sample is 1.800 . Specific gravity is 2.7. Unit weight of water is 10 . The degree of saturation of the soil is: (A) 0.65 (B) 0.70 (C) 0.54 (D) 0.61 20. Match list-I (type of soil) with list-II (mode of transportation and deposition) and select the correct answer using the codes given below the lists: List I A. Lacustrine soils B. Alluvial soils C. Aeolian soils D. Marine soils List-II 1. Transportation by wind 2. Transportation by running water 3. Deposited at the bottom of lakes 4. Deposited in sea water Codes: A B C D a. b. c. d. 1 3 3 1 2 2 2 3 3 1 4 2 4 4 1 4
16. A fine grained soil has liquid limit of 60 and plastic limit of 20. As per the plasticity chart. according to IS classification, the soil is represented by the letter symbols (A)CL (B)CI (C) CH (D) CL-ML 17. The results for sieve analysis carried out for three types of sand, P, Q and R, are given in the adjoining figure. If the fineness modulus
21. The liquid limit and plastic limit of samples are 65% and 29% respectively. The percentage of soil fraction with grain size finger than 0.002 mm is 24. The activity ratio of the soil sample is (a) 0.05 (b) 1.00 (c) 1.50 (d) 2.00
JH ACADEMY
Page 2
23. In a wet soil mass, air occupies one-sixth of its volume and water occupies one-third of its volume. The void ratio of the soil is (a) 0.25 (b) 0.5 (c) 1.00 (d) 1.50
28. A clay sample has a void ratio of 0.50 in dry state and specific gravity of solids = 2.70. Its shrinkage limit will be (a) 12% (b) 13.5% (c) 18.5% (d) 22%
24. Lacustrine soils are soils (a) Transported by rivers and streams (b) Transported by glaciers (c) Deposited in sea beds (d) Deposited in lake beds 25. The standard plasticity chart to classify fine grained soils is shown in the given figure
29. A soil has liquid limit of 60% plastic limit of 35% and shrinkage limit of 20% and it has a natural moisture content of 50%. The liquidity index of soil is (a) 1.5 (b) 1.25 (c) 0.60 (d) 0.40
The area marked X represents a) b) c) d) Silt of low plasticity Clay of high plasticity Organic soil of medium plasticity Clay of intermediate plasticity
1. 2. 3. 4.
Soil is partially saturated at degree of saturation = 60% Void ratio = 40% Water content = 30% Saturated unit weight=1.5 g/cc
Which of these statements is are correct? a) 26. A soil sample is having a specific gravity of 2.60 and a void ratio of 0.78. The water content in percentage required to fully saturate the soil at that void ratio would be (a) 10 (b) 30 (c) 50 (d) 70 c) 1, 2 and 3 2, 3 and 4 b) 1, 3 and 4 d) 1, 2 and 4
31. A soil has a liquid limit of 45% and lies above the A-line when plotted on a plasticity chart. The group symbol of the soil as per IS soil classification is (a) CH (b) CI (c) CL (d) MI
JH ACADEMY
Page 3
(b) (d) )
(
38. A soil has mass unit weight , water content w (as ratio). The specific gravity of soil soilds = G, unit weight of water= ; S is the degree of saturation of the soil is given by (a) S=
(b) S =
34. The moisture content of a clayey soil is gradually decreased from a large value. What will be the correct sequence of the occurrence of the following limits? 1. Shrinkage limit 2.Plastic limit
(d) S= 39. The saturated and dry densities of a soil are respectively 2000kg/m and 1500 kg/m. The water content (in percentage) of the soil in the saturated state would be (a) 25 (b) 33.33 (c) 50 (d) 66.66
3.Liquid limit Select the correct answer using the codes given below: (a) 1,2,3 (c) 1,3,2 (b) 3,2,1 (d) 3,1,2 35. Given the Plasticity Index (PI) of a local soil =15 and PI of sand=Zero, for a described PI of 6, the percentage of sand in the mix should be (a) 70 (b) 60 (c) 40 (d) 30 List-I 36. Consider the following statements: A Well-graded sand should have 1. 2. 3. Uniformity coefficient greater than 6 Coefficient curvature between 1 and 3 Effective size greater than 1mm A. Void ratio B. Porosity C. Degree of saturation D. Water content 1. 2. 3. 4. 5. Codes List-II 40. If a soil of sample weight 0.18kg having a volume of 10 m and dry unit weight of 1600 kg/m is mixed with 0.02 kg of water then the water content will be (a) 30% (b) 25% (c) 20% (d) 15%
41. Match List-I (terms) with List-II (formulae) and select the correct answer using the codes given below this list
Which of the statements are correct? (a) 1,2 and 3 (b) 1 and 3 (c) 1 and 2 (d) 2 and 3
JH ACADEMY
Page 4
42. If an unconfined compressive strength of 4 kg/cm in the natural state of clay reduces by four times in the remoulded state, then its sensivity will be (a ) 1 (b) 2 (c) 4 (d) 8
a) 43. If the proportion of soil passing 75 micron sieve is 50% and the liquid limit and plastic limit are 40% and 20% respectively, then the group index of the soil is (a) 3.8 (b) 6.5 (c) 38 (d) 65 b) c) d)
3 4 4 3
44. Match List-I with List-II and select the correct answer using the codes given below the list List-I A) Loess B) Peat C) Alluvial soil D) Marl List-II 1. Deposited from suspension in running water 2. deposits of marine origin 3. deposits of wind 4. organic soil CODES: A a) 3 b) 4 c) 4 B 4 3 3 4 C 2 1 2 1 D 1 2 1 2
46. The value of porosity of a soil sample in which the total volume of soil grains is equal to twice the total volume of voids would be a) 75% b) 66.66% c) 50% d) 33.33%
47. A soil has a liquid limit of 40% and plasticity index of 20% the plastic limit of the soil will be a) 20% b) 30% c) 40% d) 60%
48. A sample of saturated sand has a dry unit weight of 18 KN/m3 and a specific gravity of 2.7. If density of water 10KN/m3, the void ratio of the soil sample will be a) 0.5 b) 0.6 c) 0.4 d) 0.9
d) 3
49. A dry soil sample has equal amounts of soils and voids of volume. Its void ratio and porosity will be Void ratio a) 1.0 b) 0.5 c) 0.5 porosity (%) 100% 50% 100%
45. Match List-I (soils) with List-II (group symbols) and select the correct answer using codes given below the lists List-I A. Clayey gravel
JH ACADEMY
Page 5
50. Based on grain distribution analysis, The D10, D30 and D60 values of a given soil are 0.23mm, 0.3mm and 0.41mm respectively. As per IS code, the soil classification will be a) SW b) SP c) SM d) SC
51. The plasticity index and the percentage of grain size finer than 2 microns of a clay sample of 25 and 15 respectively. Its activity ratio is a) 2.5 b) 1.67 c) 1.0 d) 0.6
56. Given that the coefficient of curvature = 1.4 D30 = 3mm, D10 = 0.6nm, based on this information of particle size distribution for use as a sub grade, this soil will be taken to be a) Uniformly graded sand b) Well-graded sand c) Very fine sand d) Poorly-graded sand 57. Which one of the following represents relative density of saturated sand deposit having moisture content of 25% if maximum and minimum void ratio of sand are 0.95 and 0.45 respectively and specific gravity of sand particles is 2.6? a) 40% b) 50% c) 60% d) 70%
52. A soil sample having a void ratio of 1.3, water content of 50% and a specific gravity 2.60 is in a state of a) partial saturation c) over saturation b) full saturation d) under saturation
53. The natural void ratio of sand sample is 0.6 and its density index is 0.6. If its void ratio in the loosest state is 0.9, then the void ratio in the densest state will be a) 0.2 b) 0.3 c) 0.4 d) 0.5
54. Which one of the following phase diagrams represents a clay at its shrinkage limit?
58. In a soil specimen, 70% particles are passing through 4.75mm IS sieve and 40% particles are passing through 75 IS sieve. Its uniformity coefficient is 8 and coefficient of curvature is 2. As per IS classification, this soil is classified as a) SP b) GP c ) SW d) GW
59. The correct sequence of plasticity of minerals in soil in an increasing order is a) silica, kaolinite, illite, montmorillonite b) silica, kaolinite, montmorillonite, illite c) kaolinite, silica, illite, montmorillonite
d) kaolinite,silica, montmorillonite, illite 60. The predominant mineral responsible for shrinkage and swelling in black cotton soils is
JH ACADEMY
Page 6
61. Consistency as applied to cohesive soils in an indicator of its a) density c) shear strength b) moisture content d) porosity
65. What are the respective values of void ratio , porosity ratio and saturated density (in KN/m) for a soil sample which has saturation moisture content of 20% and specific gravity of grains has 2.6? ( taken density of water has 10KN/ m). a) 0.52, 1.08, 18.07 b) 0.52, 0.34, 18.07 c) 0.77, 1.08, 16.64 d) 0.52, 0.34, 20.16 66. Embankment fill is to be compacted at density of 18 KN/ m.The soil of the barrow area is at a density of 15 KN/ m. What is the estimated number of trips of 6 m capacity truck for hauling the soil required for compacting 100 m fill of the Embankment?(Assume that the soil in the barrow area and that in the Embankment are at the moisture content?) a) 14 b)18 c) 20 d) 23
62. While computing the values of limits of consistency and consistency indices , it is found that liquidity index, has a negative value Consider the following comments on this value 1. 2. 3. 4. Liquidity index cannot have a negative value and should be taken as zero Liquid index can have a negative value The soil tested is in semi solid state and stiff The soil tested in medium soft state.
Which of these statements are correct? a) 1 and 4 b) 2 and 4 b)1 and 3 d) 2 and 3
63. Two soil sample A and B have porosities =40% and =60% respectively. What is the ratio of void ratios eA :eB? a) 2:3 b) 3:2 c) 4:9 d) 9:4
67. A clay sample has a void ratio 0.54 in dry state. the specific gravity of soil solids is 2.7. what is the shrinkage limit of soil? a) 8.5% b) 10.0% c) 17.0% d) 20.0%
64. Match List-I (densities) with List-II (expressions) and select the correct answer using the codes given below the lists: (Symbols G, e, w and S stand for specific gravity of a soil grains , void ratio, unit weight of water and degree of saturation respectively) List-I a) Dry density b) Moist density c) Submerged density d) Saturated density A a) 2 b) 2 B 1 3 C 4 4 1) List-II w (G+Se)/(1+e) 2) wG/(1+e) 3) w(G+e)/(1+e) 4) w(G-1)/(1+e) D 3 1
68. Consider the following statements: 1. Mica is a clay mineral 2. Rock dust particles, even of clay size are non-plastic. 3. A particle of kaolinte is electrically changed. Which of these statements are correct? a) 1, 2 and 3 b) only 1and 2
c) Only 2 and 3 d) Only 1 and 3 69. Which of the following relation gives the value of degree of saturation S, in terms of unit Weight , water content w (as ratio) and specific gravity of soil solids Gs is unit weight of the water? a)
JH ACADEMY
Page 7
d)
70. Assertion (A): The water content of inorganic soils is determined by heating the soil in an oven at a temperature of 1050 to 1100C Reason (R): The free water, absorbed water and structural water are all completely removed from the the soil by heating it at 105 0 to 1100C. Codes: a) Both A and R is true and R is the correct explanation of A. b) Both A and R is true but R is not correct explanation of A. c) A is true but R is false. d) A is false but R is true 71. Match List- I(Equipments) with List-II (use) and select the correct answer using the codes given below the list List I A. Hydrometer B.Plate load set up C. Pycnometer . D.Direct shear apparatus. List-II 1. 2. 3. 4. Determination of shear parameters Determination of specific gravity Determination of bearing capacity Grain size distribution tests for clays
c) 2 and 3 only d) 1, 2 and 4 only 73. Consider the following statements: On additions of lime to swelling soils, 1. 2. 3. 4. Their liquid limit increases Their plastic limit increases Their shrinkage limit increases Their swelling potential decreases
Which of these statements are correct? a) 1 and 3 only b) 1,2 and 4 only b) c) 2,3 and 4 only d) 1,2,3 and 4 74. Match List-1(Soil classification symbol) with List-II ( Soil property) and select the correct answer using the codes given below the lists: List-I A) GW B) SW C) ML D) CL
List-II 1. Soil having uniformity coefficient>6 2. Soil having uniformity coefficient>4 3. Soil have low plasticity 4. Soil have low compressibility Codes: A B C D a) 1 2 4 3 b) 2 1 3 4 c) 2 1 4 3 d) 1 2 3 4
Codes : A a) b) c) d) 2 4 2 4 B 1 3 3 1 C 4 2 4 2 D 3 1 1 3
JH ACADEMY
Page 8
c) 0.67,25 and 15
Codes A B C a) 3 2 1 b) 4 3 2 c) 3 1 2 d) 2 3 4 e) 76. Match List-I(Symbol) with List-II( Soil) and select the correct answer using the codes given below the lists: List-I A. ML B. SM C. Pt
79. A cohesive soil yields a maximum dry density of 16 kN/m3 during a standard proctor Compaction test. If the specific gravity is 2.65, what would be its void ratio? a) 0.552 b) 0.624 c) 0.712 d) 0.583
80. In a wet soil mass, air occupies one-sixth of its volume and water occupies one-third of its volume. The void ratio of the soil is a) 0.25 b) 0.50 c) 0.75 d) 1.0
81. A specimen of clayey silt contains 70% silt size particles. Its liquid limit = 40. And plastic limit =20, In liquid limit test, at moisture content of 30%, required number of blows was 50. Its plasticity index, activity and consistency index will respectively be a) 20, 0.67 and 0.5
D. MH b) 20, 1.5 and 2.0 List-II c) 30, 1.5 and 0.72 1. 2. 3. 4. Silty sand Inorganic silt with large compressibility Inorganic silt with large compressibility Soil with high organic content with high compressibility d) 20, 0.286 and 0.38 82. Match List-I (Measuring device) with List-II (Soil parameter) and select the correct answer using the codes given below the lists: List-I A a) b) c) 3 4 3 B 2 1 1 C 4 3 4 D 1 2 2 Codes: A B C D a) 2 b) 3 4 1 1 4 3 2 A. B. C. D. Pycnometer Hydrometer Odometer Permeameter 1. Compressibility 2. Permeability 3. Specific gravity 4. Particle size analysis list-II
Codes:
f) 4 2 3 1 77. For a sandy soil with soil grains spherical in shape and uniform in size, what is the theoretical void ratio? a) 0.61 b) 0.71 c ) 0.91 d) 0.81
JH ACADEMY
Page 9
Codes: A B C D a) 2 3 1 4 b) 4 3 1 2 c) 2 1 3 4 d) 4 1 3 2 84. On analysis of particle size distribution of a soil, it is found that =0.1mm, =0.3mm and =0.8mm.The uniformity coefficient and coefficient of curvature, as given by the particle size distribution curve, are respectively. a) 3 and 3 c) 2.67 and 3 b) 2.67 and 1.125 d) 8 and 1.125
85. The natural water content of the soil sample was found to be 40%, specific gravity is 2.7 and void ratio 1.2; then the degree of saturation of the soil will be a) 100% b) 69% c) 87% d) 90%
86. The porosity of a soil sample having its void ratio equal to unity would be a) 33.34% b) 50.0% c) 66.66% d)75.0%
87. In a liquid limit test, the moisture content at 10 blows was 70% and that at 100 blows was 20%. The liquid limit of the soil is a) 35% b) 50% c) 65% d) 45% 88. A compacted soil sample using 10% moisture content has a weight of 200g and mass unit weight of 2.0g/cc. if the specific gravity of soil particles and water are 2.7 and 1.0, the degree of saturation of the soil is
b) c) d) 95. If the porosity of soil sample is 20%, the void ratio is a) 0.20 b) 0.80 c) 1.00 d) 0.25
JH ACADEMY
Page 10
99. The void ratio and specific gravity of a soil are 0.65 & 2.72 respectively. The degree of saturation (%) corresponding to water content of 20% is a) 65.3 b) 20.9 c) 83.7 d) 54.4 100. A saturated soil mass has a total density 22KN/ and water of 10%. The bulk density and dry density of the soil are a) 12KN/ and 20KN/ b) 22 &20KN/ c) 19.8 &19.8KN/ d) 23.2 & 19.8KN/ 101. The water content of saturated soil and the specific gravity of soil solids were found to be 30% and 2.7 respectively. Assuming the unit of water to be 10KN/ , the saturated unit weight (KN/ ) and the void ratio of the soil are a) 19.4, 0.81 b) 18.5, 0.30 c) 19.4, 0.45 d) 18.5, 0.45 102. The saturated unit weight of the sand (KN/ ) is to be find for water content= 20%, G= 2.7 and =10KN/ a) 15 b) 18 c) 21 d) 24 103. A saturated undistributed sample from a clay stratum has moisture content of 22.22% and specific weight is 2.7. assuming =10KN/ , the void ratio and saturated unit weight of clay respectively are a) 0.6 and 16.875KN/ b) 0.3 and 20.625KN/
JH ACADEMY
Page 11
121. Laboratory sieve analysis was carried out on a soil sample using complete set of standard IS sieves. Out of 500gr. Of soil used in the test, 200g was retained on IS-600 size, 250g was retained on IS-500 sieve and remaining 50g was retained on IS-425 sieve a) The Coefficient of uniformity of soil is a. 0.9 b. 1.0 c. 1.1 d. 1.2 b) The classification of soil is a. SP b. SW c. CI d. GW 122. Group symbols to silty sand and clayey sand are respectively a) SS and CS b) SM and CS c) SM and SC d) MS and CS 123. The liquid limit (LL), plastic limit (PL) and shrinkage limit (SL) of a cohesive soil satisfy the relation a) LL>PL>SL b) LL>PL>SL c) LL>PL<SL d) LL<PL>SL 124. The laboratory test results of a soil sample are given be Percentage finer than 4.75mm=60
119. A soil mass contains 40% gravel, 50%sand & 10% silt. The soil can be classified as
JH ACADEMY
Page 12
JH ACADEMY
Page 13