Escolar Documentos
Profissional Documentos
Cultura Documentos
P)
SET 2 OF 2 (UNIT 2) PROBLEM 1:- A cylindrical pipe of diameter 1.5m and thickness 1.5cm is subjected to an internal fluid pressure of 1.2N/mm2. Determine: (i) (ii) Longitudinal stress developed in the pipe, and Circumferential stress developed in the pipe. )
(Answer: -
PROBLEM 2:- A cylinder of internal diameter 2.5m and of thickness 5cm contains a gas. If the tensile stress in the material is not to exceed 80N/mm2. Determine the internal pressure of the gas. (Answer: )
PROBLEM 3:- A cylinder of internal diameter 0.5m contains air at a pressure of 7N/mm2 (gauge). If the maximum permissible stress induced in the material is 80N/mm2. Find the thickness of the cylinder. (Answer: -t=2.2 cm) PROBLEM 4:- A thin cylinder of internal diameter 1.25m contains a fluid at an internal pressure of 2N/mm2. Determine the maximum thickness of the cylinder if: (i) (ii) The longitudinal stress is not to exceed 30N/mm2. The circumferential stress is not to exceed 45N/mm2.
(Answer: -t=2.80cm) PROBLEM 5:- A gas cylinder of internal diameter 40mm is 5mm thick. If the tensile stress in the material is not to exceed 30MPa, find the maximum pressure which can be allowed in the cylinder. (Answer: - P=7.5MPa)
Page 1
PROBLEM 7:- A cylindrical shell of 1.3m diameter is made up of 18mm thick plates. Find the circumferential and longitudinal stress in the plates, if the boiler is subjected to an internal pressure of 2.4MPa. Take efficiency of the joints as 70%. (Answer: , )
PROBLEM 8:- A water main 80 cm diameter contains water at a pressure head of 100m. If the weight density of water is 9810N/m3, find the thickness of the metal required for the water main. The permissible stress is given as 20N/mm2. (Answer: -t = 2cm) PROBLEM 9:- Calculate the thickness of the metal required for a cast iron main 800mm in diameter for water at a pressure head of 100m, if the maximum permissible tensile stress is 20MN/m2 and weight of water is 10kN/m3. (Answer: - 20mm) PROBLEM 10:- A thin cylindrical shell of diameter 300mm and wall thickness 6mm has hemispherical ends. If there is no distortion of the junction under pressure determine the thickness of hemispherical ends. Take E=208GN/m2, and Poissons ratio=0.3. (Answer: - t2=2.47mm) PROBLEM 11:- A boiler is subjected to an internal steam pressure of 2N/mm2. The thickness of boiler plate is 2.0cm and tensile stress is 120N/mm2. Find out the maximum diameter, when efficiency of longitudinal joint is 90% and that of circumferential joint is 40%.
Page 2
(Answer: - d = 1080mm, p = 1.44 N/mm2) PROBLEM 13:- A cylinder of thickness 1.5cm has to withstand maximum internal pressure of 1.5N/mm2. If the ultimate tensile stress in the material of the cylinder is 300N/mm2, factor of safety 3.0 and joint efficiency 80%, determine the diameter of the cylinder. (Answer: - d=1.6m) PROBLEM 14:- Calculate: (i) (ii) (iii) The change in diameter. The change in length. The change in volume of a thin cylindrical shell 100cm diameter, 1cm thick and 5m long when subjected to internal pressure of 3N/mm2. Take the value of and Poissons ratio, =0.3.
(Answer: - 0.06375cm, 0.075cm, 5595.96cm3) PROBLEM 15:- A cylindrical thin drum 80cm in diameter and 3m long has a shell thickness of 1cm. If the drum is subjected to an internal pressure of 2.5N/mm2, determine: (i) (ii) Change in diameter. Change in length, and
Page 3
(Answer: - 0.035cm, 0.0375cm, 1507.96cm3) PROBLEM 16:- A cylindrical shell 90cm long 20cm internal diameter has thickness of metal as 8mm is filled with fluid at atmospheric pressure. If an additional 20cm3 of fluid is pumped into the cylinder, find (i) (ii) Take (Answer: - P=5.95N/mm2, The pressure exerted by the fluid on the cylinder and The hoop stress induced. and Poissons ratio, =0.3. )
PROBLEM 17:- A cylindrical vessel, whose ends are closed by means of rigid flange plates, is made of steel plate 3mm thick. The length and the internal diameter of the vessel are 50cm and 25cm respectively. Determine the longitudinal and hoop stresses in the cylindrical shell due to an internal fluid pressure of 3N/mm2. Also calculate the increase in length, diameter and volume of the vessel. Take (Answer: and Poissons ratio, = 0.3. , ) PROBLEM 18:- A cylindrical vessel is 1.5m diameter and 4m long is closed at ends by rigid plates. It is subjected to an internal pressure of 3N/mm2. If the maximum principal stress is not to exceed 150N/mm2, find the thickness of the shell. Assume and Poissons ratio, =0.25. Find the changes in diameter, length and volume of the shell. (Answer: -15mm, 0.984mm, 0.75mm, 10602875mm3)
Page 4
PROBLEM 21:- A hollow cylindrical drum 600mm in diameter and 3m long has a shell thickness of 10mm. If the drum is subjected to an internal air pressure of 3N/mm2, determine the increase in its volume. Take And Poissons ratio, =0.3 for the material. (Answer: - 655103.5mm3) PROBLEM 22:- A thin cylindrical shell with following dimensions is filled with a liquid at atmospheric pressure. Length=1.2m, External diameter=20cm, Thickness of metal=8mm. Find the value of the pressure exerted by the liquid on the walls of the cylinder and the hoop stress induced if an additional volume of 25cm3 of liquid is pumped into the cylinder. Take And Poissons ratio, =0.33 for the material. (Answer: - 7.77N/mm2, 89.42N/mm2)
Page 5
PROBLEM 25:- A thin cylindrical tube of 90-mm internal diameter and 6mm thickness and closed at the end is subjected to an internal pressure of 8MPa. Determine the maximum and minimum principal stresses and the maximum shear stress if a torque of 4000N.m is also applied to the tube. (Answer: )
PROBLEM 26:- A cylindrical water tank of height 25m, inside diameter 2.2m, having vertical axis is open at the top. The tank is made of steel having yield stress of 210MN/m2. Determine the thickness of steel used when the tank is full of water. Efficiency of the longitudinal joint=70%, factor of safety=3 (Answer: - 6mm) PROBLEM 27:- A cylindrical air drum is 2.25m in diameter with plates 1.2cm thick. The efficiency of the longitudinal and circumferential joints is 75% and 40%. It the tensile stress in the plating is to be limited to 120MN/m2. Find the maximum safe air pressure.
COMPILED BY AMIT SINGH 9827740442 (amit28niist@gmail.com) Page 6
(Answer: - 0.0945mm, 120236.5mm3) PROBLEM 36:- Calculate the increase in volume of a spherical shell 1m in diameter and 1 cm thick when it is subjected to an internal pressure of 1.6MN/m2.
(Answer: - 219.9cm3)
Page 8
(Answer: - 0.111m, 31.714MN/m2, 1.522MN/m2) PROBLEM 38: - The cylindrical shell is shown in figure is 1m long and has diameter =200mm. The metal thickness is 6mm. It has spherical ends. Calculate the change in volume, if the internal pressure is raised to 1.5N/mm2, take .
(Answer: - Total change in volume=8443.03mm3) PROBLEM 39: - A boiler drum consists of a cylindrical portion 4m long, 1.5m in diameter and 2.25 cm thick. It is closed by hemispherical ends. In a hydraulic test to 6MN/m2, how much additional water will be pumped in after initial filling at
Page 9
PROBLEM 41:- A cast iron pipe of 300mm internal diameter and 12mm thick is wound closely with a single layer of circular steel wire of 5mm diameter under a tension of 60MPa. Find the initial compressive stress in the pipe section. Also find the stresses set up in the pipe and steel wire, when water under a pressure of 4MPa is admitted into the pipe. Take E for cast iron and steel as 100GPa and 200GPa respectively. Poissons ratio=0.3 (Answer: - 13.6MPa, 111.4MPa) PROBLEM 42:- A cast iron pipe of 240-mm inside diameter and 15-mm thick is closely wounded with a layer of 6-mm diameter steel wire under a stress of 35MPa. Find the stresses developed in the pipe and the steel wire when water is admitted into the pipe at a pressure of 3MPa. For steel E=204GPa For cast iron E=102GPa; Poissons ratio=0.3 (Answer: )
PROBLEM 43:- A cast iron pipe of 200mm internal diameter and 12mm thick is wound closely with a single layer of circular steel wire of 5mm diameter, under a
COMPILED BY AMIT SINGH 9827740442 (amit28niist@gmail.com) Page 10
PROBLEM 44:- A gun metal tube of 100mm bore, wall thickness 2.5mm is closely wounded externally by a steel wire 1mm diameter. Determine the tension under which the wire must be wound on the tube, if an internal radial pressure of 3MN/m2 is required before the tube is subjected to tensile stress in the circumferential direction. Take: For gun metal: E=102GN/m2; 1/m=0.35 For steel: E=210GN/m2 (Answer: 129.12MN/m2)
PROBLEM 45:- The internal and external diameters of a copper tube are 42mm and 45mm respectively. It is closely wound with a steel wire of 1mm diameter. Determine the required tension in the wire so that an internal pressure of 2MPa produces a tensile circumferential stress of 8MPa in the tube. (Answer: - Winding tension=10.53N) PROBLEM 46:- A rim type flywheel is rotating at a speed of 2400r.p.m. If the mean diameter of the flywheel is 750mm and density of the material of the wheel is 8000kg/m3, then find the hoop stress produced in the rim due to rotation. Take E=200GN/m2 then what will be the change in diameter of the flywheel due to rotation. (Answer: - 71.061MN/m2, 0.2664mm)
Page 11
Given for oil: K (bulk modulus) = 2800MN/m2; For steel: E = 210GN/m2, and Poissons ratio = 0.28 (Answer: -0.267MN/m2, 8.9MN/m2) PROBLEM 49: - The ends of a thin cylinder, 180mm internal diameter and wall thickness 3.0mm are closed by rigid plates and it is then filled with a liquid. When an axial compressive force of 33.6kN is applied to the cylinder, the pressure of the liquid rises by 72kN/m2. If E = 200GN/m2 and Poissons ratio = 0.3, find the bulk modulus of the liquid. (Answer: - K = 3.75GN/m2) PROBLEM 50: - A cylinder made of bronze 180mm outside diameter and 15mm thick is strengthened by a single layer of steel wire 2.25mm diameter wound over it under a constant stress of 75MN/m2. The cylinder is subjected to an internal pressure of 27MN/m2, with rise in temperature of the cylinder by 1200C. Assuming the cylinder to be a thin shell with closed ends, determine the final value of: (i) The stress in the wire.
Page 12
Page 13