Escolar Documentos
Profissional Documentos
Cultura Documentos
L1.0
MAIN STEPS:
1. Create New Document:
- File -> New -> Document
- Select: Part
- Select: Name
- Input Arc Datas
- Press OK
- Create New Project if necessary
- Start 3D-mode with OK
2. Create sketch
- Select: New Sketch -> XY-plane
3. Sketch rectangle:
- Open mouse menu (mouse right)
- Select: Line -> Rectangle
- Point first point
- Move cursor vertical or horizontal
to get symbol, that indicates X or Y
locking and accept it (mouse left).
(picture 2)
- Point second point.
- Point third point, that definies
height or width. (picture 3)
4. Set symmetry constraints:
- Select vertical side lines (2) (Ctrlpressed)
- Select: Constraints ->
Symmetry
- Point: Middle cross vertical line
(see info line)
- Select horizontal border lines (2)
(Ctrl-pressed)
- Select: Constraints ->
Symmetry
- Point: Middle cross horizontal line
5. Set distance constraints:
- Select 2 lines (Ctrl-pressed)
- Select: Constraints -> Distance
- Show position
- Input distance, value: 100
- Select 2 lines (Ctrl-pressed)
- Select: Constraints -> Distance
- Show position
- Input distance, value: 150
6. End sketchin by selecting OK ->
Select: Extruded Boss
- Length, value: 10 mm
L1
Rectangle
=
)(
150
Symmetry
100
)(
Symmetry
2
3
Rectangle, symmetrical
2003-09-10 JMe
L2
Equilateral Triangle
Note: Inputs automaticly
coincidence constraint
to midcross -> polyline
starts from vertical line
Symmetry
=
)(
60
=
160
Equilateral Triangle
2003-09-10 JM
L3
60
Rounded
1. Sketch rectangle
2. Sketch circles
- Midpoint to 1/2-point
- Radiuspoint to corner
3. Distances
80
60
80
2003-09-10 JM
L4
60
Angle
R2
60
3. Add Round:
- Select point
- Select Round
- Input radius
=
100
R2
60
= 100
R2
60
= 100
2003-09-10 JMe
L5
Corner piece
=
=
Coincident
2. Set coincident
3. Set orthogonal
=
=
40
4. Set angle
5. Set distances
- Distances in brackets NOT needed
6. Select OK, Extruded Boss,
Length, value: 10 mm
70
30
35
20
(100.3)
25
40
(154.7)
Corner piece
2003-09-10 JM
L6
Strainer Plate
150
1. Sketch rectangle
2. Dimensions
3. Sketch circle
4. Dimensions, diameter and
distances
25
14
20
220
150
14
20
220
2003-09-10 JM
L7
Cam
1. Sketch horizontal line
2. Edit it to construction line
3. Sketch arches:
- Midpoint: lines endpoint
- Note: counter clockwise
4. Sketch diagonal lines
- To arch endpoints
=
Tangential
Tangential
Tangential
Tangential
R3
7. Constraints, distance
8. Constraints, radius
R15
60
Select OK, Extruded Boss, Length, Value: 40 mm
Cam
2003-09-10 JM
L8
U-Profile
2. Constraints "equidistance"
- Note: right order
Equidistance
=
=
=
1. Sketch polyline
- Use horizontal- vertical locking
=
=
2
3
=
=
4
"Equidistance" select contraint
first
1
4
Equidistance
1
Equidistance
2
3. Constraints, distance
4. Edit distances
Equidistance
3
2
Select OK, Extruded Boss,
Length, Value: 100
25
160
U-profile
2003-09-10 JM
L9
Bearing 180
1. Sketch horizontal lines
- Start from cross
2. Sketch arc
3. Sketch circles
concentric
8. Check; coincident between
7. Constraints, midpoint
- Arc line and holes midpoint
- Select 2 horizontal lines
- Select constraint "Midpoint"
- Select midpoint of arc
6. Constraints, equalradius
- Select 2 arches
coincident
midpoint
equalradius
coincident
9. Constraints, distances
10. Constraintst, radius
12.Mirror
10
30
R5
30
10
50
R30
Bearing
axis
50
2003-09-10 JM
L10
100
Pipe
Concentric
168.3
Concentric
Diameter
1.5 (give here formula = s)
Distance
2002-09-20 JM
L11
65
15
Frame
10
40
45
65
15
155
26
75
2003-09-11 JMe
24
60
16
L12
Plate
Sketch 1:
150
Tangent
70
170
Sketch 2:
Sketch circles to points:
- endpoints
- 1/2-points
40
40
20
10
Concentric
Equal distance
Select edit sketch and edit values.
Plate
2003-09-11 JMe