Escolar Documentos
Profissional Documentos
Cultura Documentos
DEL PER
CURSO DE PREPARACIN PARA
EXAMEN CWI
SIMULACRO DE EXAMEN
Parte A
Fundamentos
5. What AWS document describes the rules for the CWI certification program?
5. Que documento de AWS describe las reglas para el programa de certificacin como CWI?
a. AWS 5.5
b. AWS D1.1
c. AWS QC1
d. AWS 5.1
e. AWS 14.1
6. A green stripe on a tungsten electrode designates:
6. Una banda verde en un electrodo de tungsteno designa:
a. pure tungsten
a. tungsteno puro
b. 1% thoriated tungsten
b. 1% tungsteno toriado
c. 2% thoriated tungsten
c. 2% tungsteno toriado
d. zirconiated tungsten
d. tungsteno circoneado
e. none of the above
e. ninguna de las anteriores
7. A 'Hot Work Permit' is required for:
7. Un permiso de trabajo en caliente es requerido para:
a. all welding operations
a. todas las operaciones de soldadura
b. all cutting operations
b. todas la operaciones de corte
c. all preheating operations
c. todas las operaciones de precalentamiento
d. areas where a fire hazard may occur during a welding, cutting, or preheating operation
d. reas donde un riesgo de fuego podra ocurrir durante las operaciones de soldadura, corte, o
precalentamiento
e. all of the above
e. todas las anteriores
8. What are the three welding inspector certifications covered in AWS QC1?
8. Cuales son las tres certificaciones de Inspector de Soldadura cubiertas por AWS QC1?
a. CAWI, CWI, BWI
a. CAWI, CWI, BWI
b. CWI, CAWI, SCWI
b. CWI, CAWI, SCWI
c. SCWI, CWI, ACWI
c. SCWI, CWI, ACWI
d. Levels I, II, and III
d. Niveles I, II y III
e. None of the above
e. Ninguna de las anteriores
9. The abbreviation 'MSDS' means:
9. La abreviacin MSDS significa:
a. Management Support and Daily Safety
a. Soporte administrativo y seguridad diaria
b. Material Strength and Discontinuity Sheet
b. resistencia del material y hoja de discontinuidades
c. Material Safety Data Sheet
15. NDE personnel (other than CWIs) are typically certified to what document?
15. El personal de END (excepto CWI) son generalmente certificados bajo que documento?
a. AWS QC1
a. AWS QC1
b. AWS D1.1
b. AWS D1.1
c. API1104
c. API1104
d. ASNT SNT-TC-1A
d. ASNT SNT-TC-1A
e. certification is not needed
e. no es necesaria una certificacin
16. The width of a cut is referred to as the:
16. El ancho de un corte es referido como:
a. gap
a. abertura
b. dross
b. escoria
c. kerf
c. ranura o corte
d. drag
d. desviacin (arrastre)
e. none of the above
e. ninguna de las anteriores
17. You must have a high school diploma to become a CWI.
17. Tu debes tener un diploma de secundaria para llegar a ser un CWI:
a. true
a. verdadero
b. false
b. falso
18. The welding symbol below shows the use of what type of completed weld?
18. El smbolo de soldadura de abajo muestra el uso de que tipo de soldadura completada?
c. harmful
c. dainas
d. secondary currents
d. Corrientes secundarias
e. b and c above
e. b y c son correctas
29. Which of the following welding problems is the result of a distorted magnetic field
that deflects the welding arc?
29. Cual de los siguientes problemas de soldadura es el resultado de un campo magntico
distorsionado que desva el arco de soldadura?
a. cracks
a. fisuras
b. short circuiting
b. corto circuito
c. arc blow
c. soplo magntico
d. insufficient welding current
d. insuficiente corriente de soldeo
e. all of the above
e. todas las anteriores
30. In the welding symbol below, the 1/8 dimension refers to what?
30. En el smbolo de abajo, la dimensin 1/8 a que se refiere?
a. groove angle
a. ngulo de canal
b. root face
b. cara de soldadura
c. depth of preparation
c. profundidad de penetracin
d. weld size
d. tamao de soldadura
e. root opening
e. abertura de raz
31. The acronym KASH stands for:
31. El acrnimo KASH corresponde a:
a. knowledge, attitude, skills, and habits
a. conocimiento, actitud, habilidades, y hbitos
b. knowledge, application, skills, and habits
b. conocimiento, aplicacin, habilidades y hbitos
c. knowledge, attitude, skills, and honesty
c. conocimiento, actitud, habilidades, y honestidad
d. knowledge, application, skills, and honesty
d. conocimiento, aplicacin, habilidades, y honestidad
e. knowledge, attitude, sincerity, and honesty
e. conocimiento, actitud, sinceridad, y honestidad
32.Which of the following is not considered a type of metal transfer for GMAW?
32. Cual de los siguientes no es considerado un tipo de transferencia de metal para GMAW?
a. short circuiting
a. corto circuito
b. spray
b. spray
c. globular
c. globular
d. droplet
d. goteado
e. pulsed arc
e. arco pulsado
33. Which of the following types of metal transfer in GMAW provides the lowest amount
of heat to the work piece, and therefore is prone to incomplete fusion?
33. Cual de los siguientes tipos de transferencia en GMAW provee la menor cantidad de calor a
la pieza de trabajo, y por lo tanto es propenso a falta de fusin?
a. short circuiting
a. corto circuito
b. spray
b. spray
c. globular
c. globular
d. droplet
d. goteado
e. pulsed arc
e. arco pulsado
34. If applied to a 1 in thick weld joint, the welding symbol below describes what type of
weld?
34. Si se aplica a una junta soldada de 1 pulg. de espesor, el smbolo de soldadura de abajo
que tipo de soldadura describe.
e. work lead
e. cable de la pieza de trabajo
36. Which welding process is considered to be a chemical welding process?
36. Cual de los siguientes procesos de soldadura es considerado un proceso de soldadura
qumico
a. SMAW
a. SMAW
b. ESW
b. ESW
c. SAW
c. SAW
d. OAW
d. OAW
e. none of the above
e. ninguno de los anteriores
37. Brazing differs from welding in that:
37. El proceso Brazing difiere de la soldadura en que:
a. no filler metal is used
a. no se usa material de aporte
b. an oxyfuel flame is used
b. una llama oxicombustible es usada
c. the base metal is not melted
c. el metal base no es fundido
d. all of the above
d. todas las anteriores
e. none of the above
e. ninguna de las anteriores
38. The symbol below depicts what type of joint?
38. El smbolo de abajo describe que tipo de junta?
a. flare V-groove
a. canal en V curvo
b. flare bevel groove
b. canal de bisel curvo
c. edge flange
c. borde en pestaa
d. corner flange
d. esquina en pestaa
e. none of the above
e. ninguna de las anteriores
39. Of the following metals, which cannot be efficiently cut using OFC?
39. De los siguientes metales, cual no puede ser eficientemente cortado usando OFC
a. high-carbon steel
a. acero de alto carbono
b. low-carbon steel
b. acero de bajo carbono
c. medium-carbon steel
c. acero de medio carbono
d. austenitic stainless steel
d. acero inoxidable austentico
e. none of the above
e. ninguna de las anteriores
40. Which of the following uses a focused beam of electrons as a heat source?
40. Cual de los siguientes usa un haz de electrones enfocado como fuente de calor?
a. EBW
a. EBW
b. ESW
b. ESW
c. EGW
c. EGW
d. a and c above
d. a y c son correctas
e. none of the above
e. ninguna de las anteriores
41. In the welding symbol below, the supplementary symbol shown on the other side
location represents:
41. En el smbolo de soldadura de abajo, el smbolo suplementario mostrado en el otro lado
representa:
a. back weld
a. soldadura de refuerzo
b. backing weld
b. soldadura de respaldo
c. melt-through of weld from arrow side
c. melt-through exceso de penetracin de la soldadura por el lado de la flecha
d. a and b above
d. a y b son correctas
e. b and c above
e. b y c son correctas
42. The welding inspector should have a basic understanding of:
42. El inspector de soldadura debe tener un conocimiento bsico de:
a. welding processes
a. procesos de soldadura
b. non destructive testing methods
b. mtodos de ensayos no destructivos
c. a and b above
c. a y b
d. codes and standards
d. cdigos y estndares
e. all of the above
e. todas las anteriores