Escolar Documentos
Profissional Documentos
Cultura Documentos
PLANO DE
ARREGLO GENERAL II
0 4
04.1.
Taller 04
|
CONSTRUCCIÓN
A R R E G L O
de la planta alta, la
planta baja y el per-
G E N E R A L
1 Desactive el layer
sombreado. 3 Dibuje dos líneas
auxiliares (Figura
01) y luego un rec-
tángulo para delimi-
Command: _rectang
FIGURA 02: Dibujo del contorno. Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
a
ness/Width]: _nea to
Specify other corner point: @8.25,5.6784
ENTER
(Figura 02).
02
b 03
65
endpoin
TALLER AUTOCAD
b
a
entrad
04
c f
d g
66
Para dibujar la fachada, tomaremos como
ts
TALLER 04 • ARREGLO GRAL.
referencia las medidas de la planta alta, la planta
baja y el perfil, para trazar las líneas auxiliares.
da FIGURA 05:
Medianera.
05
Command:
6 Dibuje la medianera.
RECTANG
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
ness/Width]: _endp of
@0.25,0
Specify other corner point: @0.35,2.3
ENTER
ENTER
Specify other corner point: @0.45,2.3
ENTER
(Figura 05).
67
06
TALLER AUTOCAD
a Fachada
FIGURA 06:
Interior de la fachada.
b contorno interior
7 Con el comando Rectangle (Rectángulo) dibu-
je el contorno interior de la fachada.
c
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@0.9,0
ENTER
Specify other corner point: @5.8,4.6507
ENTER
Command:
RECTANG
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @7.6,5.3784
ENTER
d
(Figura 06).
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@1.2,0
ENTER
Specify other corner point: @2.2,0.6716
ENTER
e
(Figura 07).
68
de agua
Tanque
TALLER 04 • ARREGLO GRAL.
FIGURA 07: Base del tanque de agua. FIGURA 08: Copia del tanque.
a a
07
b b
08
c 10 Dibuje la chimenea.
Command: _line
Specify first point: _from Base point: _endp of <Offset>:
@-0.225,0
ENTER
Specify next point or [Undo]: @0,0.25
ENTER
Specify next point or [Undo]: @0.25,0
ENTER
Specify next point or [Close/Undo]: _per to
Specify next point or [Close/Undo]:
9 Copie el tanque de agua de la vista en
corte y ubíquelo en el centro de la base
que ha dibujado en el paso anterior.
ENTER
69
09
b
TALLER AUTOCAD
a FIGURA 09:
Construcción de la chimenea.
Chim
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/
Thickness/Width]: _from Base point: _mid of <Offset>:
@-0.30,-0.30
ENTER
Specify other corner point: @0.60,-0.60
ENTER
(Figura 10).
d 12
13
Seleccione el layer aberturas y dibuje
las puertas.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/
Thickness/Width]: _from Base point: _endp of <Offset>:
@0.05,-0.0184
ENTER
e
Specify other corner point: @0.8,-0.8
ENTER
70
TALLER 04 • ARREGLO GRAL.
FIGURA 10: Ventana del dormitorio. FIGURA 11: Construcción e inserción de la ventana.
a
10
a
b
b
c
c
Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PScale/
PX/PY/PZ/PRotate]: _from Base point: _endp of
<Offset>: @0,-0.04
11
ENTER
(Figura 11).
71
TALLER AUTOCAD
a b
Ventan
12
FIGURA 12:
Construcción e inser-
ción de las ventanas
c
superiores.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
d
@0.075,0
ENTER
Specify other corner point: @0.8,-0.67
ENTER
Command: _block
Select objects: 1 found
Select objects:
Specify insertion base point: _endp of
e
Command: _insert
Specify insertion point or [Scale/X/Y/Z/Rotate/PSca-
le/PX/PY/PZ/PRotate]: _from Base point: _endp of <Off-
set>: @0.025,0
ENTER
(Figura 12).
72
TALLER 04 • ARREGLO GRAL.
14
b
c
15 Dibuje las puertas.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@0.05,0 Command: _mirror
Select objects: Specify opposite corner: 4 found
ENTER
Select objects: 1 found, 5 total
Specify other corner point: @0.8,2
Select objects:
ENTER
Specify first point of mirror line: _mid of
Specify second point of mirror line: _per to
(Figura 13).
Delete source objects? [Yes/No] <N>:
ENTER
73
TALLER AUTOCAD
FIGURA 16: Construcción del garage.
Garage a 16
15
b
17 Trabaje en el layer sombreado y utilice
el comando Hatch (sombreado) para darle
el corte a la medianera.
(Figura 15).
Command: _rectang
c
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _endp of
Specify other corner point: @-3.2,2.3
ENTER
d
Layer aberturas.
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thick-
ness/Width]: _from Base point: _endp of <Offset>:
@0.50,0
ENTER
Specify other corner point: @2.4,2
ENTER
(Figura 16).
74
FIGURA 15:
Sombreado. TALLER 04 • ARREGLO GRAL.
FIGURA 17:
Parte posterior. FIGURA 21: Dibujos.
FIGURA 18:
Corte constructivo. 21
FIGURA 19:
Vista en corte.
FIGURA 20:
Ubicación de los dibujos.
a
17
b
18
c
19
75
TALLER AUTOCAD
FIGURA 22:
Copia de la planta baja.
FIGURA 23:
Sombreado del techo.
FIGURA 24:
Techo de la casa.
Límite
del terreno
FIGURA 25: Límite del terreno.
a
22
a
25
23
24
c
22 Para construir el entorno, copie la
planta baja y desde el layer techo dibu-
je el techo tomando como referencia las medi-
das de las vistas laterales.
76
a
26
FIGURA 26: Límite del terreno. FIGURA 27:
TALLER 04 • ARREGLO GRAL.
Construcción de la galería.
a
27
b b
Command: _rectang
Specify first corner point or [Chamfer/Elevation/Fillet/
Thickness/Width]: _from Base point: _endp of <Offset>:
@-15,0
c
ENTER
Specify other corner point: @40,-16
ENTER
(Figura 25).
Command: _rectang
77
TALLER AUTOCAD
29
28
a
a
b
b
c 25 Inserte un sombreado.
(Figuras 29 y 30).
(Figura 31).
(Figura 32).
78
FIGURA 30:
Piso exterior. TALLER 04 • ARREGLO GRAL.
FIGURA 31:
Puertas delanteras y piso exterior.
FIGURA 32:
Elementos del dibujo Landscaping.
FIGURA 33: Configuración y sombreado.
33
30
a 31
a
32
(Figura 33).
79
TALLER AUTOCAD
FIGURA 36:
Plano de entorno en Paper Space
(Espacio Papel).
FIGURA 37:
Plano de Arreglo General en Paper
Space (Espacio Papel).
FIGURA 38:
Plano de detalles constructivos
en Paper Space (Espacio Papel).
36
35
a 38
c 80
31 Seleccione la ficha Layout 1 (Presenta-
ción 1) y construya el plano de entorno.
(Figuras 36, 37, 38).