Escolar Documentos
Profissional Documentos
Cultura Documentos
This is an update to the Home Based Salvage & Recycling Business Manual. Check here
for more information:
http://www.recyclingsecrets.com/home-based-salvage-recycling-business-manual.htm
Also, be sure to wear the proper clothing including acid proof gloves, apron
and facemask. Also wear a respirator that protects from chemical fumes –
sulfuric acid especially. You will also need a ventilation system. There are
links to scrubbers for ventilation, safety equipment and related items at the
end of this report.
http://www.atsdr.cdc.gov/phs/phs.asp?id=254&tid=47
Finally, check with your local public health and environmental departments
about the use of sulfuric acid. Also, be sure to take steps to safely and
legally dispose of any waste.
Plated Gold
This relatively simple system will recover up to about 1/4 ounces of very
fine gold per hour depending on material.
The power supply is a 6-12 volt 60 ampere battery charger. The 6 volt
setting provides the approximately 8 volts required. I fabricated the basket
out of copper wire that I salvaged. If you do not have any on hand copper
grounding wire can be had at most any hardware store. The cathode also
came from my salvage pile. If you do not have any large chunks of copper,
a local metal scrap yard should sell you a piece. For mine I used a
2”x2”x1/4” piece of copper buss bar. I haven’t tried it, but I would think
that a flattened piece of larger copper tubing would work as well.
Material
Operation
First off, make sure you are using only sulfuric acid. Many people think that
the only way to remove gold is with aqua regia – this is not the case. As
aqua regia works, it dissolves ALL of the material into solution so most of it
is used up dissolving metal substrate not gold. The aqua regia process uses
large quantities of acids and is very dangerous. Another problem with using
aqua regia is that the base metal is no longer available as scrap – a secondary
revenue stream is lost. This system for removing gold plate (fig. 1) uses
relatively small amounts of sulfuric acid and it is reusable to boot.
I use a plastic bucket filled with 1 gallon of sulfuric acid. The bucket is then
placed in a plastic wash tub filled with cold water. The temperature of the
acid should not be more than 100 degrees farenheit. I have found that this
small system will run for several hours at less than 100 degrees farenheit
with only cold water in the wash tub before having to add any ice to reduce
the temperature.
I fill the copper basket with gold plated material, place it in the bucket full of
sulfuric acid and connect the anode (the basket) to the positive lead and the
cathode (block of copper in bottom of bucket) to the negative lead from the
battery charger. I then turn on my fume hood and make sure I have all of
my safety equipment in place and then I turn on the battery charger.
When I stripped very heavy plated material it would take ½ to a full hour to
remove 1/8 ounce of gold. Thinner plated material will take less time and,
of course, yield less gold.
I can tell when the gold is removed by watching the ammeter on the charger.
When I see it drop to near zero I know that I’m almost there. I give the
basket a couple of shakes and the meter pops back up for a minute or two
and then goes back to near zero. I repeat this shaking process a couple of
times. You will notice that there is a dark brown sludge at the bottom of the
bucket. This is the gold plus some copper and other materials.
If you have more material to de-plate, remove the basket from the bucket,
dump the basket into another bucket. Then fill the basket with new material
and start the process again.
Copyright © 2010 Michael R. Meuser, All Rights Reserved 3
Once done with the batch or batches it’s time to recover the gold. First,
wash the material you’ve been working with in a 1:1 diluted water and
sulfuric acid solution. Use it sparingly – just enough to remove any residue
from the de-plating process. You are washing off some of the gold sludge
that has accumulated on the material rather than precipitating to the bottom
of the bucket. Add this cleaning solution to the bucket.
Pour the sulfuric acid de-plating solution and sludge into two large glass
beakers and boil it. After 5 hours the sulfuric acid will be clear and
yellowish or greenish if some copper was dissolved. At the bottom of the
beakers you will see a spongy coagulated mass. This is near pure gold. Be
sure to boil this under your exhaust hood and wear a respirator. During the
first couple of hours the boiling is producing sulfur dioxide.
The next step is to allow the solution to cool. This can take up to 12 hours
for it to reach room temperature. Once cool pour off the solution for later
reuse or disposal and place the spongy material in a vacuum filter. Once the
spongy material is dry, it can be melted in a crucible. You can add a little
saltpeter (Potassium Nitrate KNO3) as it is melting to improve the purity.
Saltpeter is available in garden stores and departments as a stump remover
or you can get it from a chemical supply house.
I’ve created a web page listing various safety equipment and supplies that I
have mentioned in this report. Check here for more information:
http://www.recyclingsecrets.com/salvage-recycling-products.htm
Mike Meuser
http://www.recyclingsecrets.com
P.S. You are free to share this document in any manner that you wish as
long as you do not change the contents in any way or form.