Você está na página 1de 13

INTRODUCTION:-

In 1845, German physicist Gustav Kirchhoff described two laws. In electromagnetic fields
these laws are generalizations of Ohm's law. These Kirchhoff's circuit law are very useful in
solving circuit problems. Kirchhoff's circuit laws are two equalities that deal with
the conservation of charge and energy in electrical circuits, and it widely used in electrical
engineering, they are also called Kirchhoff's rules or simply Kirchhoff's laws. The two
Kirchhoff’s Laws tell us about the relationships between voltages and currents in circuits.

Both circuit rules can be directly derived from Maxwell's equations, but Kirchhoff
preceded Maxwell and instead generalized work by Georg Ohm.

The current entering any junction is equal to the current leaving that junction. i1 + i4 = i2 + i3

The first law is Kirchhoff's current law. Kirchhoff's current law is also known as Kirchhoff's
first law and Kirchhoff's junction law. This law states that 'The sum of current into a junction
equals the sum of current out of the junction'. This is the same as Kirchhoff's junction law. In
a junction, theelectric charge's sum preservation law is applied. If the entering value of the
current is i2 and i3, this current splits into the current of i1 and i4. Then the equation (i1 + i4
= i2 + i3) is satisfied. The right picture gives an example. This Kirchhoff's first law is that
charge is not destroyed or created in a junction point. This is based by an electric charge
preservation law.

The sum of all the voltages around the loop is equal to zero. v1 + v2 + v3 + v4 = 0
Another is Kirchhoff's voltage law. Kirchhoff's voltage law is also known as Kirchhoff's
second law, a closed circuit law, and Kirchhoff's loop law. The algebraic sum of the voltage
(potential) differences in any loop must equal zero.(This circuit is a closed circuit) Any
complex circuit can be divided into many closed circuits. This law means that in the circuit
there is an electric cell and electric resistance. The electric cell gives the charge a
electromotive force, and then the electric resistance dissipates this force. But in electric
resistance if the direction is opposite of the current's direction, this electric resistance adds to
the electromotive force. This Kirchhoff's second law is based on potential energy
preservation law.

Contents:-
SOME BASIC POINTS FOR KCL LAW

 Kirchhoff's current law (KCL)


o (a)-Changing charge density
o Uses
 Kirchhoff's voltage law (KVL)

o Positive and Negative Signs in Kirchhoff's Voltage Law


o (b) Electric field and electric potential
o Application

Application of Kirchoff's Circuit Laws


 Limitations
 Conclusion

 4-References

SOME BASIC POINTS FOR KCL LAW:-

When analysing either DC circuits or AC circuits using Kirchoff's Circuit Laws a number
of definitions and terminologies are used to describe the parts of the circuit being analysed
such as: node, paths, branches, loops and meshes. These terms are used frequently in circuit
analysis so it is important to understand them.

• Circuit - a circuit is a closed loop conducting path in which an electrical current


flows.
• Path - a line of connecting elements or sources with no elements or sources included
more than once.
• Node - a node is a junction, connection or terminal within a circuit were two or more
circuit elements are connected or joined together giving a connection point between two or
more branches. A node is indicated by a dot.
• Branch - a branch is a single or group of components such as resistors or a source
which are connected between two nodes.
• Loop - a loop is a simple closed path in a circuit in which no circuit element or node
is encountered more than once.
• Mesh - a mesh is a single open loop that does not have a closed path. No components
are inside a mesh.
• Components are connected in series if they carry the same current.
• Components are connected in parallel if the same voltage is across them.

(1)-Kirchhoff's current law (KCL)

This law is also called Kirchhoff's point rule, Kirchhoff's junction rule (or nodal rule),
and Kirchhoff's first rule.

The principle of conservation of electric charge implies that:

At any node (junction) in an electrical circuit, the sum of currents flowing into that node is
equal to the sum of currents flowing out of that node.

or
The algebraic sum of currents in a network of conductors meeting at a point is zero.
(Assuming that current entering the junction is taken as positive and current leaving the
junction is taken as negative).
Recalling that current is a signed (positive or negative) quantity reflecting direction towards
or away from a node, this principle can be stated as:

n is the total number of branches with currents flowing towards or away from the node.

This formula is also valid for complex currents:

The law is based on the conservation of charge whereby the charge (measured in coulombs)
is the product of the current (in amperes) and the time (which is measured in seconds).
Kirchhoff’s Current Law states that: ‘the algebraic sum of currents at a node is zero’. Two
points might need further explanation:

(a)-a ‘node’ is the technical term for a junction in a circuit, where two or more branches are
joined
together. Fig. 2.1 shows a node with four branches connected.

(b)- the phrase ‘algebraic sum’ reminds us that we have to take account of the current
direction, as well as magnitude, when applying Kirchhoff’s Current Law.
This Law is used in circuit analysis to define relationships between currents flowing in
branches of the circuit. For example, in Fig. 2.1 the currents flowing in the four branches
connected to the node have been defined as I1, I2, I3, I4 and Kirchhoff’s Current Law allows
us to write down an equation relating these currents. Looking closely at Fig. 2.1, we see that
two of the currents (I1, I2) are flowing towards the node, while the other two currents (I3, I4)
are flowing outwards. The ‘algebraic sum’ needs to take account of this difference in relative
direction.

To apply Kirchhoff’s Current Law rigorously, we must first make an arbitrary choice of
positive current direction. Suppose currents flowing in to the node (I1, I2) are treated as
positive contributions to the algebraic sum (and conversely currents flowing from the node
are treated as negative contributions), then the algebraic sum of currents would be written: +
I1 + I2 - I3 - I4 , and according to Kirchhoff’s Current Law this algebraic sum is equal to
zero:
+ I1 + I2 - I3 - I4 =0 ----------------------------------------------------------- (2.1)
The same result could be obtained with the opposite choice of positive current direction. If
currents flowing from the node (I3, I4) are treated as positive contributions to the algebraic
sum, then the algebraic sum of currents would be written: - I1 - I2 + I3 + I4 , and equating
this algebraic sum to zero:

- I1 - I2 + I3 + I4 = 0 ----------------------------------------------------------- (2.2)

which is the same relationship as Eqn. 2.1 with all terms multiplied by –1.
It must be emphasised that the choice of sign convention when using Kirchhoff’s Current
Law is entirely arbitrary and, of course, makes no difference to the result obtained. However,
it is good practice to be consistent in your choice, because this minimises the chance of
making a mistake when writing down the algebraic sum. Eqns. 2.1 and 2.2 can be re-arranged
to show that:

I1+ I2 = I3 + I4 -------------------------------------------------------------------(2.3)

and referring back to Fig. 2.1 we see that this equation is showing that current flowing into
the node is equal to the current flowing out. This formulation arises naturally from physical
considerations of current as the flow of charge. Charge does not accumulate at a node and
therefore any charge flowing into the node through one or more branches must flow out from
the node through other branches. Therefore, current flowing into is equal to current flowing
out of the node.

Worked example 2.1


Calculate the current I flowing into the node.
Solution:-
Choosing currents flowing into the node as positive and applying Kirchhoff’s
Current Law: +3 –2 +I = 0, so I = -1 A
The current flowing into the node is –1IA, which is the same as +1IA flowing out of the
node.

Worked example 2.2


Calculate the current I defined in the diagram.

Solution:-

In this problem, there are two nodes, each with three branches connected. Begin by defining
the current I’ flowing in the branch between the two nodes. The direction of I’ has been
chosen randomly: it may turn out to have a positive or negative value. Choosing currents
flowing out of the nodes as
positive and applying Kirchhoff’s Current Law at each node:

-(-4) + 2 + I’ = 0, so I’ = -6 A and: -I’ – 6 + I = 0, so I = I’ + 6 = 0 A


but is there any easier way? Yes! We can merge the two separate nodes into a single
‘supernode’, shown in red in the lower diagram. The supernode can’t accumulate charge, so
Kirchhoff’s Current Law can be applied to currents in branches connected to it. Making the
same choice of current direction:

-(-4) + 2 + I – 6 = 0, so I = 0 A
________________________________________________________________________

(a)-Changing charge density


Physically speaking, the restriction regarding the "capacitor plate" means that Kirchhoff's
current law is only valid if the charge density remains constant in the point that it is applied
to. This is normally not a problem because of the strength of electrostatic forces: the charge
buildup would cause repulsive forces to disperse the charges.

However, a charge build-up can occur in a capacitor, where the charge is typically spread
over wide parallel plates, with a physical break in the circuit that prevents the positive and
negative charge accumulations over the two plates from coming together and cancelling. In
this case, the sum of the currents flowing into one plate of the capacitor is not zero, but rather
is equal to the rate of charge accumulation. However, if the displacement current dD/dt is
included, Kirchhoff's current law once again holds. (This is really only required if one wants
to apply the current law to a point on a capacitor plate. In circuit analyses, however, the
capacitor as a whole is typically treated as a unit, in which case the ordinary current law holds
since exactly the current that enters the capacitor on the one side leaves it on the other side.)

More technically, Kirchhoff's current law can be found by taking the divergence of Ampère's
law with Maxwell's correction and combining with Gauss's law, yielding:

This is simply the charge conservation equation (in integral form, it says that the current
flowing out of a closed surface is equal to the rate of loss of charge within the enclosed
volume (Divergence theorem)). Kirchhoff's current law is equivalent to the statement
that the divergence of the current is zero, true for time-invariant ρ, or always true if the
displacement current is included with J.

Uses:-

A matrix version of Kirchhoff's current law is the basis of most circuit simulation
software, such as SPICE. This law can be used, along with Kichoff's voltage law, Ohm's law,
Norton and Thevanin equivalents, and other transformations to analyze various circuits.
A specific example of Kirchoff's current law is the analysis of a transistor. If you know the
current through the collector or emitter resistor, you can assume (within reasonable limits)
that the current through the other resistor is the same. (The "limits" have to do with the
contribution from the base current, but that is generally negligible)

(2)-Kirchhoff's voltage law (KVL):-

The sum of all the voltages around the loop is equal to zero. v1 + v2 + v3 - v4 = 0

This law is also called Kirchhoff's second law, Kirchhoff's loop (or mesh) rule,
and Kirchhoff's second rule.

The principle of conservation of energy implies that

The directed sum of the electrical potential differences (voltage) around any closed circuit is
zero.
or
More simply, the sum of the emfs in any closed loop is equivalent to the sum of the potential
drops in that loop.

or
The algebraic sum of the products of the resistances of the conductors and the currents in
them in a closed loop is equal to the total emfavailable in that loop.
Similarly to KCL, it can be stated as:

Here, n is the total number of voltages measured. The voltages may also be complex:
This law is based on the conservation of "energy given/taken by potential field" (not
including energy taken by dissipation). Given a voltage potential, a charge which has
completed a closed loop doesn't gain or lose energy as it has gone back to initial potential
level.

This law holds true even when resistance (which causes dissipation of energy) is present in a
circuit. The validity of this law in this case can be understood if one realizes that a charge in
fact doesn't go back to its starting point, due to dissipation of energy. A charge will just
terminate at the negative terminal, instead of positive terminal. This means all the energy given by the
potential difference has been fully consumed by resistance which in turn loses the energy as heat dissipation.

To summarize, Kirchhoff's voltage law has nothing to do with gain or loss of energy by electronic components
(resistors, capacitors, etc.). It is a law referring to the potential field generated by voltage sources. In this
potential field, regardless of what electronic components are present, the gain or loss in "energy given by the
potential field" must be zero when a charge completes a closed loop.

Positive and Negative Signs in Kirchhoff's Voltage Law:-

Using the Voltage Rule requires some sign conventions, which aren't necessarily as clear as
those in the Current Rule. You choose a direction (clockwise or counter-clockwise) to go
along the loop.

When travelling from positive to negative (+ to -) in an emf (power source) the voltage drops,
so the value is negative. When going from negative to positive (- to +) the voltage goes up, so
the value is positive.

When crossing a resistor, the voltage change is determined by the formula I*R, where I is the
value of the current and R is the resistance of the resistor. Crossing in the same direction as
the current means the voltage goes down, so its value is negative. When crossing a resistor in
the direction opposite the current, the voltage value is positive (the voltage is increasing).

(b)-Electric field and electric potential


Kirchhoff's voltage law could be viewed as a consequence of the principle of conservation of
energy. Otherwise, it would be possible to build a perpetual motion machine that passed a
current in a circle around the circuit.

Considering that electric potential is defined as a line integral over an electric field,
Kirchhoff's voltage law can be expressed equivalently as
which states that the line integral of the electric field around closed loop C is zero.

In order to return to the more special form, this integral can be "cut in pieces" in order to get
the voltage at specific components.

APPLICATION OF KIRCHHOFF'S VOLTAGE LAW:-

Kirchhoff's voltage law can be written as an equation, as shown below:

Ea + Eb + Ec + . . . En = 0

where Ea, Eb, etc., are the voltage drops or emf's around any closed circuit loop.
To set up the equation for an actual circuit, the following procedure is used.

Assume a direction of current through the circuit. (The correct direction is


desirable but not necessary.)
Using the assumed direction of current, assign polarities to all resistors through
which the current flows.
Place the correct polarities on any sources included in the circuit.
Starting at any point in the circuit, trace around the circuit, writing down the
amount and polarity of the voltage across each component in succession. The
polarity used is the sign AFTER the assumed current has passed through the
component. Stop when the point at which the trace was started is reached.
Place these voltages, with their polarities, into the equation and solve for the
desired quantity.

Example: Three resistors are connected across a 50-volt source. What is the
voltage across the third resistor if the voltage drops across the first two resistors
are 25 volts and 15 volts?

Solution: First, a diagram, such as the one shown in figure 3-23, is drawn. Next,
a direction of current is assumed (as shown). Using this current, the polarity
markings are placed at each end of each resistor and also on the terminals of the
source. Starting at point A, trace around the circuit in the direction of current
flow, recording the voltage and polarity of each component. Starting at point A
and using the components from the circuit:

Substituting values from the circuit:


Figure 3-23. - Determining unknown voltage in a series circuit.

Application of Kirchoff's Circuit Laws

These two laws enable the Currents and Voltages in a circuit to be found, ie, the circuit is said
to be "Analysed", and the basic procedure for using Kirchoff's Circuit Laws is as follows:

• 1. Assume all voltage sources and resistances are given. (If not label them V1, V2 ...,
R1, R2etc)
• 2. Label each branch with a branch current. (I1, I2, I3 etc)
• 3. Find Kirchoff's first law equations for each node.
• 4. Find Kirchoff's second law equations for each of the independent loops of the
circuit.
• 5. Use Linear simultaneous equations as required to find the unknown currents.

As well as using Kirchoff's Circuit Law to calculate the voltages and currents circulating
around a linear circuit, we can also use loop analysis to calculate the currents in each
independent loop helping to reduce the amount of mathematics required using just Kirchoff's
laws. In the next tutorial about DC Theory we will look at Mesh Current Analysis to do just
that.

Limitations:-
This is a simplification of Faraday's law of induction for the special case where there is no
fluctuating magnetic field linking the closed loop. Therefore, it practically suffices for
explaining circuits containing only resistors and capacitors.

In the presence of a changing magnetic field the electric field is not conservative and it
cannot therefore define a pure scalar potential—the line integral of the electric field around
the circuit is not zero. This is because energy is being transferred from the magnetic field to
the current (or vice versa). In order to "fix" Kirchhoff's voltage law for circuits containing
inductors, an effective potential drop, or electromotive force (emf), is associated with
each inductance of the circuit, exactly equal to the amount by which the line integral of the
electric field is not zero by Faraday's law of induction.

Conclusion for Kirchoff's Circuit Law:-

We saw in the Resistors above that a single equivalent resistance, ( RT ) can be found when
two or more resistors are connected together in either series, parallel or combinations of both,
and that these circuits obey Ohm's Law.

However, sometimes in complex circuits such as bridge or T networks, we can not simply use
Ohm's Law alone to find the voltages or currents circulating within the circuit. For these
types of calculations we need certain rules which allow us to obtain the circuit equations and
for this we can use Kirchoff's Circuit Law.

we see that at junction, there may be many conductors. Current enters from the top, then
goes out in the other directions and, from the Current Law, we know the algebraic sum of
these must be zero. If we knew the resistance values of the resistors, and the current coming
into the junction, we could use the Voltage Law equations to determine the currents in each
of the lower paths, if the resistors were unequal.

This is why Kirchhoff's Laws are such powerful tools


References

 Paul, Clayton R. (2001). Fundamentals of Electric Circuit Analysis. John Wiley &
Sons. ISBN 0-471-37195-5.

 Serway, Raymond A.; Jewett, John W. (2004). Physics for Scientists and Engineers
(6th ed.). Brooks/Cole. ISBN 0-534-40842-7.

 Tipler, Paul (2004). Physics for Scientists and Engineers: Electricity, Magnetism,
Light, and Elementary Modern Physics (5th ed.). W. H. Freeman. ISBN 0-7167-0810-8.

Você também pode gostar