Catalogo SKF

Deep groove
ball bearings
Nomenclature
6200-2Z J/C3 HC5 GJN

1
1. Seals, shields & snap rings:
2. Cage designs:
4. Suffix:
RSH
Contact seal of synthetic rubber

(NBR) on one side for bearings
up to 52 mm O.D.
Full ceramic bearing
RS1

(NBR) on one side for bearings
above 52 mm O.D.
Machined brass cage,

rolling element guided
HC4
HC5
VA201
TC

(FRM) on one side for high
temperature capability
Phenolic cage,
inner ring guided
VA208
RS2
Special specifications for

high temperature applications
Pressed brass cage,

ball guided
5. Lubrication:
Cage of glass fiber reinforced

polyamide 6.6, ball guided
GJN
High temperature, long life

NLGI 2 grease with urea
thickener and mineral oil
WT
Wide temperature range,

long life NLGI 2-3 grease
with urea thickener and ester oil
HT51
High temperature NLGI 2

grease with polyurea
thickener and mineral oil
LHT23
Long life, quiet running

NLGI 2 grease with lithium
thickener and ester oil
MT47
Medium temperature, quiet

running NLGI 2 grease with
lithium thickener and mineral oil
MT33
Medium temperature, quiet

running NLGI 3 grease with
lithium thickener and mineral oil
LHT30
Dow Corning Molykote

44 Medium
LHT64
Shell Aeroshell #7,

MIL-G-23827
W64
LT10
Solid oil
Pressed steel cage,

ball guided
(not marked on bearings)
RSL
Low friction seal of synthetic

rubber (NBR) on one side for
bearings up to 52 mm O.D.
TN9
RZ

rubber (NBR) on one side for
bearings above 52 mm O.D.
3. Clearance/tolerance:
Z
2RSH
2RS2
Shield on one side

(NBR) on both sides for
(FPM) on both sides for high
temperature capability
2RSL

rubber (NBR) on both sides for
2RZ

rubber (NBR) on both sides for
bearings above 52 mm O.D.
2Z
NR
Shields on both sides
C1
C2
(C0)*
C3
C4
C08
Clearance < C2
C78
C70
C782
C783
Combination of C70 and C08
Clearance < Normal

Normal clearance
Clearance > Normal
Clearance > C3
ABEC5 running accuracy
inner and outer
Reduced I.R. and O.R. diameter

C78 and C2 clearance
C78 and C3 clearance
Snap ring groove and snap ring

on outer ring
* Not marked on bearing or package.
Note: C3 clearance, J-steel cages and
quiet running characteristics available
in JEM bearings. See page 27.
Ceramic ball set

Special specifications for
kiln trucks
Low temperature NLGI 2

grease with lithium thickener
and diester oil
25
Deep groove ball bearings
Product
Details
Technical
features
Boundary dimensions
In accordance with ISO 15-1998
Tolerances
Normal, ABEC 1
P6 (SKF Explorer)
Running accuracy
Up to 52 mm O.D. P5, ABEC 5

52 mm to 110 mm O.D. P6, ABEC 3
>110 mm O.D. Normal, ABEC 1
Heat stabilization
257 F (125 C)
Misalignment
2 minutes of arc
Cage material
Standard
Steel
Optional
Machined brass (M)
Axial load max
0.5 x C0 for 6200, 6300 and 6400 series

0.25 x C0 for 61800, 61900 and 6000 series
Seals
2RS1 Synthetic rubber (NBR) seals

2RS2 Synthetic rubber (FRM) seals
Shields
2Z Stamped steel
Single row
deep groove ball bearing
(data tables on page 32)
and ABEC 5
26
Single row
deep groove ball bearing
Max type
Introduction
Introduction
ABEC 5 single row bearings
Deep groove ball bearings are used in a

particularly wide variety of applications. They
are relatively simple in design, non-separable,
capable of operating at high and even very
high speeds, and require little attention or
maintenance in service provided the customer
selects the appropriate bearing specifications
for his application. These characteristics
coupled with a price advantage make deep
groove ball bearings the most popular of all
rolling bearings.
SKF produces deep groove ball bearings in
a large number of designs and sizes. The most
numerous are the single row bearings without
filling slots (Conrad assembly). The bearings
with filling slots described in the section starting on page 47 are used in special applications
and consequently only a limited range is
produced.
Basic design
Deep groove ball bearings, single row
SKF single row deep groove ball bearings have
deep, uninterrupted raceways and a high
degree of conformity between balls and raceways. This enables them to carry axial loads in
both directions in addition to radial loads even
at high speeds. Single row deep groove ball
bearings are suitable for a wide variety of
applications and are therefore produced in a
large number of sizes and designs.
Single row deep groove ball bearings of the
basic design, i.e. open at both sides, (Figure 1)
are produced by SKF in several series and in a
very wide range of diameters. Those bearings
of the basic design which are also produced as
shielded or sealed bearings may, for manufacturing reasons, have recessed outer ring
shoulders to take the shields or seals.
SKF produces single row deep groove ball

bearings in a higher precision class (ABEC 5).
These products are most frequently used in
high-speed applications or where precision is
critical as in cutting tools, electric motors,
handheld tools, and spindles. ABEC 5 bearings
are produced in the 6200 and 6300 series
and are available in an open version only.
They can be supplied with either a brass (Y)
or phenolic (TC) cage.
Deep groove ball bearings with filling

slots (Max type)
Single row deep groove ball bearings with filling slots incorporate a greater number of balls
than the corresponding size without filling slot,
and have a filling slot in both outer and inner
rings. The radial load carrying capacity is higher than that of bearings without filling slot, but
their axial load carrying capacity is small. They
are also unable to operate at the high speeds
normally associated with deep groove ball
bearings.
SKF deep groove ball bearings with filling
slots are available in various designs to meet
market demands. The most common are
described below (Figure 2) and are listed in
the tables on page 47.
SKF Explorer class

bearings
High performance SKF Explorer deep
groove ball bearings are printed in blue in
the product tables. The higher performance
of SKF Explorer deep groove ball bearings
also includes quieter running. SKF Explorer
bearings retain the designation of the earlier
standard bearings. However, each bearing
and its box are marked with the name SKF
Explorer. Additional details on SKF Explorer
performance class bearings can be found on
page 23.
Product highlights
Fast, quiet, robust bearings
If the application is demanding
and quiet running, smoothness,
strength and low heat generation
are mandatorySKF deep groove
ball bearings fit the bill.
Quiet running
High precision balls and specially
designed raceway grinding equipment
are used by SKF to produce some of
the quietest running bearings available.
Quality performance in demanding applications

Capable of meeting the severest
demands in terms of operating speed,
operating temperature, vibration, high
running accuracy, low friction, and the
ability to function in a contaminated
environment with available seals and
shields.
Optimized internal geometry

The internal geometry has been optimized for longer life, quieter running,
improved seal attachment, low friction
and increased ability to accommodate
slight misalignments without reducing
bearing life.
Large product assortment

Available in a wide range (2.5 to
800 mm inside bore diameter), the
basic SKF design is available with a
choice of shields, seals and snap rings.
In addition, SKF produces max-type
deep groove ball bearings with a
filling slot.
JEM bearings
Figure 1
Figure 2
In the USA, SKF offers bearings with

C3 internal clearance, steel cages and
quiet running characteristics packaged
as JEM bearings.
GJN grease provided as

standard in JEM bearings
SKF provides GJN, a high temperature
urea based grease, as the standard for
all JEM deep groove ball bearings. GJN
is accepted by major OEM electric
motor manufactures in the U.S. and
offers a wide range of operating temperature and is quiet running.
Deep groove ball bearing
single row
Deep groove ball bearing

with filling slots (Max type)
27

Introduction
Variations
Bearings with shields
Bearings with contact seals
Warning!
Bearings with shields, designation suffix Z or

2Z, are produced in one of two designs,
depending on the bearing series and size
(Figure 3). The shields are made of sheet steel
and normally have a cylindrical extension in the
shield bore to form a long sealing gap with the
inner ring shoulder.
Shielded bearings are primarily intended for
applications where the inner ring rotates. If the
outer ring rotates, there is a risk that the
grease will leak from the bearing at high
speeds.
Bearings with contact seals, designation suffixes RSH, 2RSH or RS1, 2RS1 are manufactured
in three designs depending on bearing series
and size (Figure 5).
Safety precautions for fluoro rubber

Fluoro rubber is very stable and harmless in
normal operating conditions up to +392 F
(+200 C). However, if exposed to extreme
temperatures above +572 F (+300 C), e.g.
fire or the flame of a cutting torch, fluoro
rubber seals give off hazardous fumes. These
fumes can be harmful if inhaled, as well as to
the eyes. In addition, once the seals have
been heated to such temperatures, they are
dangerous to handle even after they have
cooled and should not touch the skin. If it is
necessary to handle bearings with seals that
have been subjected to high temperatures,
such as when dismounting the bearing, the
following safety precautions should be
observed:
Bearings with low friction seals

SKF deep groove ball bearings with lowfriction seals, designation suffixes RSL, 2RSL
or RZ, 2RZ are manufactured in two designs
depending on bearing series and size
(Figure 4).
Bearings in the 60, 62 and 63 series up to
52 mm outside diameter are equipped with
RSL seals to design (a).
Other bearings have RZ seals (b).
The seals form an extremely narrow gap with
the cylindrical surface of the inner ring shoulder or recess profile and are practically noncontracting. Because of this, bearings fitted
with low-friction seals can be operated at the
same high speeds as bearings with Z shields,
but with improved seal performance.
The low-friction seals are made of oil and
wear-resistant acrylonitrile butadiene rubber
(NBR) with a sheet steel reinforcement.
The permissible operating temperature range
for these seals is -40 to +212 F
(-40 to +100 C) and up to +250 F (+120 C)
for brief periods.
Figure 3
Bearings in the 60, 62 and 63 series up to

52 mm outside diameter are equipped with
RSH seals to design (a).
Other bearings have RS1 seals, which seal
against the cylindrical surface of the inner
ring shoulder (b) indicated by dimension
d1 in the product table or against a recess
in the inner ring side face (c) indicated by
dimension d2 in the product table.
The seals are inserted in recesses in the
outer ring and provide good sealing at this
position without deforming the outer ring.
Standard seals are made of acrylonitrile
butadiene rubber (NBR) with a sheet steel reinforcement. The permissible operating temperature range for these seals is -40 to 212 F
(-40 to +100 C) and up to +250 F (+120 C)
for brief periods.
When sealed bearings are operated under
extreme conditions, e.g. very high speeds or
high temperatures, grease leakage may occur
at the inner ring. For bearing arrangements
where this would be detrimental, special design
steps must be undertaken, please consult the
SKF application engineering service.
Bearings with snap ring groove

Deep groove ball bearings with a snap ring
groove can simplify arrangement design as the
bearings can be axially located in the housing
by a snap (or retaining) ring (Figure 6). This
saves space. Appropriate snap rings are shown
in the product table with designation and
dimensions and may be supplied separately or
already mounted on the bearing.
Figure 5
Figure 4
28
Always wear protective goggles, gloves and

appropriate breathing apparatus,
Place the remains of the seals in an
airtight plastic container marked
with a symbol for material will etch,
Follow the safety precautions in the
appropriate material safety data sheet
(MSDS).
If there is unintentional contact with the
seals, wash hands with soap and plenty of
water and flush eyes with plenty of water and
consult a doctor immediately. If the fumes have
been inhaled, consult a doctor immediately.
The user is responsible for the correct use
of the product during its service life and its
proper disposal. SKF takes no responsibility
for the improper handling of fluoro rubber seals
or for any injury resulting from their use.
Figure 6
Introduction
Lubrication
Masses
Internal clearance
Bearings with shields or seals at both sides are

supplied as standard filled with a grease which
has good rust inhibiting properties and which is
suitable for operating temperatures between
-22 and +230 F (-30 to +110 C). The bearings are lubricated for life and are maintenance
free. They should on no account be heated to
temperatures above 250 F (120 C), nor
should they be washed. By special order, bearings with shields or seals can be supplied with
other greases, e.g. for a temperature range of
-40 to +300 F (-40 to +150 C).
The quantity of grease supplied is appropriate
to the size of the bearing and normally fills
between 25 and 35% of the free space in the
bearing. Open bearings are supplied with a rust
preservative that is compatible with most standard greases and should not be removed prior
to mounting or lubricating.
The masses given in the tables are for the basic

design of the bearing. The mass of bearings with
shield(s), seal(s) or snap ring groove differs only
slightly from that of the basic bearing.
Radial internal clearance (Table 1)

SKF single row deep groove ball bearings are
produced with Normal radial internal clearance
(CN or C0 not marked on bearing) as standard.
Radial clearance selection is based on factors
such as high speed, operating temperature,
shaft fits and axial movement limitations. The
availability of bearings with clearances other
than Normal should be checked before ordering.
The suffix JEM indicates an internal clearance
greater than Normal (C3). Many of the bearings,
particularly the smaller sizes, are also available
with radial internal clearance, which is greater
than (C3) or less than (C2) Normal.
The values of the clearance limits for single
row deep groove ball bearings are shown in
Table 1 and the values of the clearance limits
for max type ball bearings are shown in Table 3
on page 30. Both conform to ISO 5753-1991
(ABMA standard 20-1996) for the size range
covered by this standard. The values apply to
unmounted bearings under zero measuring load.
Table 1
Radial internal clearance of deep groove ball bearings
Bore
diameter
d
over incl.
mm
Radial internal clearance

C2
min max min
m
in
2.5
10
18
10
18
24
0
0
0
7
9
10
0.0000 0.0003
0.0000 0.0004
0.0000 0.0004
2
3
5
13
18
20
0.0001 0.0005
0.0001 0.0007
0.0002 0.0008
8
11
13
23
25
28
24
30
40
30
40
50
1
1
1
11
11
11
0.0000 0.0004
0.0000 0.0004
0.0000 0.0004
5
6
6
20
20
23
0.0002 0.0008
0.0002 0.0008
0.0002 0.0009
13
15
18
50
65
80
65
80
100
1
1
1
15
15
18
0.0000 0.0006
0.0000 0.0006
0.0000 0.0007
8
10
12
28
30
36
0.0003 0.0011
0.0004 0.0012
0.0005 0.0014
100
120
140
120
140
160
2
2
2
20
23
23
0.0001 0.0008
0.0001 0.0009
0.0001 0.0009
15
18
18
41
48
53
160
180
200
180
200
225
2
2
4
25
30
32
0.0001 0.0010
0.0001 0.0012
0.0002 0.0013
20
25
28
61
71
82
225
250
280
250
280
315
4
4
8
36
39
45
0.0002 0.0014
0.0002 0.0015
0.0003 0.0018
31
36
42
315
355
400
355
400
450
8
8
10
50
60
70
0.0003 0.0020
0.0003 0.0024
0.0004 0.0028
50
60
70
450
500
560
500
560
630
10
20
20
630
710
800
710
800
900
C5
min max
m
min
in
0.0006 0.0011
0.0007 0.0013
0.0008 0.0014
20
25
28
37
45
48
0.0008 0.0015
0.0010 0.0018
0.0011 0.0019
41
46
51
0.0009 0.0016
0.0011 0.0018
0.0012 0.0020
30
40
45
53
64
73
0.0012 0.0021
0.0016 0.0025
0.0018 0.0029
38
46
53
61
71
84
0.0015 0.0024
0.0018 0.0028
0.0021 0.0033
55
65
75
90
105
120
0.0022 0.0035
0.0026 0.0041
0.0030 0.0047
61
71
81
97
114
130
0.0024 0.0038
0.0028 0.0045
0.0032 0.0051
90 140
105 160
120 180
0.0035 0.0055
0.0041 0.0063
0.0047 0.0071
102 0.0021 0.0040

117 0.0025 0.0046
132 0.0029 0.0052
91 147
107 163
120 187
0.0036 0.0058
0.0042 0.0064
0.0047 0.0074
135 200
150 230
175 255
0.0053 0.0079
0.0059 0.0091
0.0069 0.0100
92 0.0012 0.0036
97 0.0014 0.0038
110 0.0017 0.0043
87 152 0.0034 0.0060

97 162 0.0038 0.0064
110 180 0.0043 0.0071
140 217
152 237
175 260
0.0055 0.0085
0.0060 0.0093
0.0069 0.0102
205 290
255 320
260 360
0.0081 0.0114
0.0100 0.0126
0.0102 0.0142
120 0.0020 0.0047

140 0.0024 0.0055
160 0.0028 0.0063
120 200 0.0047 0.0079

140 230 0.0055 0.0091
160 260 0.0063 0.0102
200 290
230 330
260 370
0.0079 0.0114
0.0091 0.0130
0.0102 0.0146
290 405
330 460
370 520
0.0114 0.0159
0.0130 0.0181
0.0146 0.0205
80
0.0004 0.0031
90
0.0008 0.0035
100 0.0008 0.0039
80 180 0.0031 0.0071

90 200 0.0035 0.0079
100 220 0.0039 0.0087
180 290 0.0071 0.0114

200 320 0.0079 0.0126
220 350 0.0087 0.0138
290 410
320 460
350 510
0.0114 0.0161
0.0126 0.0181
0.0138 0.0201
410 570
460 630
510 700
0.0161 0.0224
0.0181 0.0248
0.0201 0.0276
30
30
30
120 0.0012 0.0047

130 0.0012 0.0051
150 0.0012 0.0059
120 250 0.0047 0.0098

130 280 0.0051 0.0110
150 310 0.0059 0.0122
250 390 0.0098 0.0154

280 440 0.0110 0.0173
310 490 0.0122 0.0193
390 560
440 620
490 690
0.0154 0.0220
0.0173 0.0244
0.0193 0.0272
560 780
620 860
690 960
0.0220 0.0307
0.0244 0.0339
0.0272 0.0378
900 1 000 40
1 000 1 120 40
160 0.0016 0.0063

170 0.0016 0.0067
160 340 0.0063 0.0134

170 370 0.0067 0.0146
340 540 0.0134 0.0213

370 590 0.0146 0.0232
540 760
590 840
0.0213 0.0299
0.0232 0.0331
760 1040 0.0299 0.0409

840 1120 0.0331 0.0441
max
Normal
min max min
m
in
C4
min max
m
min
in
0.0003 0.0009
0.0004 0.0010
0.0005 0.0011
14
18
20
29
33
36
28
33
36
0.0005 0.0011
0.0006 0.0013
0.0007 0.0014
23
28
30
23
25
30
43
51
58
0.0009 0.0017
0.0010 0.0020
0.0012 0.0023
0.0006 0.0016
0.0007 0.0019
0.0007 0.0021
36
41
46
66
81
91
0.0014 0.0026
0.0016 0.0032
0.0018 0.0036
0.0008 0.0024
0.0010 0.0028
0.0011 0.0032
53
63
73
max
C3
min max min
m
in
max
max
max
29

Introduction
Loads
Equivalent dynamic bearing load for
single bearings, Conrad type
P = Fr when Fa / Fr e
P = XFr + YFa when Fa / Fr > e
where
P = equivalent dynamic bearing load
Fr = radial load acting on the bearing
Fa = axial load acting on the bearing
X, Y and e = factors from Table 2
The X and Y factors required for the calculation
of the equivalent bearing load of deep groove
ball bearings are dependent on the ratio of the
axial load Fa to the basic static load rating C0
They are also influenced by the magnitude of
the radial internal clearance; increased clearance enables heavier axial loads to be carried.
If the bearings are mounted with the usual
fits (tolerance j5 to n6 depending on shaft
diameter, and J7 for the housing) the values
of e, X and Y given in Table 2 can be used to
calculate the equivalent load. If a clearance
greater than Normal is chosen because a
reduction in clearance will be obtained in operation, for example, as a result of strong heating
of the inner ring, then the values of the factors
under Normal clearance should be used.

single row deep groove ball bearings
with filling slots
The requisite minimum radial load to be

applied in such cases can be determined by
using the Interactive Engineering Catalog on
the SKF website www.skf.com or by contacting
SKF Applications Engineering.
However, the weight of the components
supported by the bearing, together with the
external forces, often exceeds the requisite
minimum load. If this is not the case, an
additional radial load must be applied to the
bearing; for example, by increasing belt tension,
by applying a preload to the inner or outer
rings, or by using springs.
Special solutions
using deep groove
ball bearings
Bearings with inch boundary
dimensions
High temperature (kiln truck) bearings
for extreme temperatures
Stainless steel bearings for water/moist
environments
INSOCOAT for electrically insulating a
bearing from stray current
Bearings with ceramic balls for extreme
speed or electrical insulation
Double row deep groove (4200 series)
for increased load
Frequency vibration data

Frequency vibration data is available on the
SKF website www.skf.com in the Interactive
Engineering Catalog or by contacting SKF
Applications Engineering.
Details on these special solution products

are available in other SKF publications,
which can be supplied upon request.
Table 2
Calculation factors for single row deep groove ball bearings
Single bearings and bearing pairs in tandem
Normal clearance
C3 clearance
C4 clearance
P = Fr + Fa
provided Fa / Fr 0.6
Fa/C0
Bearings with filling slots are unsuitable for

axial loads Fa greater than 0.6 Fr and deep
groove ball bearings without filling slot should
be used instead.
0.025
0.04
0.07
0.13
0.25
0.5
0.22
0.24
0.27
0.31
0.37
0.44
0.56
0.56
0.56
0.56
0.56
0.56
2.0
1.8
1.6
1.4
1.2
1.0
0.31
0.33
0.36
0.41
0.46
0.54
0.46
0.46
0.46
0.46
0.46
0.46
1.75
1.62
1.46
1.30
1.14
1.00
0.4
0.42
0.44
0.48
0.53
0.56
0.44
0.44
0.44
0.44
0.44
0.44
1.42
1.36
1.27
1.16
1.05
1.00
Minimum load
In order to provide satisfactory operation of all ball and roller bearings they
must always be subjected to a given
minimum load.
This is also true of deep groove ball bearings,
particularly if they run at high speeds where the
inertia forces of the balls and cage, and the
friction in the lubricant can have a detrimental
influence on the rolling conditions in the bearing
and may cause damaging sliding movements to
occur between the balls and the raceways.
30
Table 3
Radial internal clearance of deep groove ball bearings with filling slots
Bore
diameter
d
over incl.
mm

C2
min max min
m
in
18
24
30
24
30
40
0
1
1
10
11
11
0.0000 0.0004
0.0000 0.0004
0.0000 0.0004
5
5
6
20
20
20
40
50
65
50
65
80
1
1
1
11
15
15
0.0000 0.0004
0.0000 0.0006
0.0000 0.0006
6
8
10
80
100
18
0.0000 0.0007
12
max
Normal
min max min
m
in
C3
min max
m
min
in
0.0002 0.0008
0.0002 0.0008
0.0002 0.0008
13 28
13 28
15 33
0.0005 0.0011
0.0005 0.0011
0.0006 0.0013
23
28
30
0.0002 0.0009
0.0003 0.0011
0.0004 0.0012
18 36
23 43
25 51
0.0007 0.0014
0.0009 0.0017
0.0010 0.0020
36
0.0005 0.0014
30 58
0.0012 0.0023
max
max
Introduction
Snap ring and snap ring groove dimensions
Table 4
Snap ring and groove dimensions - ball bearings
Outer ring
O.D.
D
Groove
dia.
max.
D3
Groove
location
max.
C2
Groove
width
min.
b
Fillet
radius
max.
r0
Ring
thickness
max.
f
Ring section
height
max.
h
Ring
gap
End
cover
Db
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm in
mm
in
40
1.5748
38.10
1.500
2.06
0.081
1.35
0.053
0.4
0.016
1.12
0.044
3.25
0.128
0.12
45
1.8
47
1.8504
44.60
1.756
2.46
0.097
1.35
0.053
0.4
0.016
1.12
0.044
4.04
0.159
0.15
53
2.1
52
2.0472
49.73
1.958
2.46
0.097
1.35
0.053
0.4
0.016
1.12
0.044
4.04
0.159
0.15
58
2.3
62
2.4409
59.61
2.347
3.28
0.129
1.90
0.075
0.6
0.024
1.70
0.067
4.04
0.159
0.15
68
2.7
72
2.8346
68.81
2.709
3.28
0.129
1.90
0.075
0.6
0.024
1.70
0.067
4.85
0.191
0.19
80
3.1
80
3.1496
76.81
3.024
3.28
0.129
1.90
0.075
0.6
0.024
1.70
0.067
4.85
0.191
0.19
88
3.5
85
3.3464
81.81
3.221
3.28
0.129
1.90
0.075
0.6
0.024
1.70
0.067
4.85
0.191
0.19
93
3.7
90
3.5400
86.79
3.417
3.28
0.129
2.70
0.106
0.6
0.024
2.46
0.097
4.85
0.191
0.19
98
3.9
100
3.9370
96.80
3.811
3.28
0.129
2.70
0.106
0.6
0.024
2.46
0.097
4.85
0.191
0.19
108
4.3
110
4.3307
106.81
4.205
3.28
0.129
2.70
0.106
0.6
0.024
2.46
0.097
4.85
0.191
0.19
118
4.6
120
4.7244
115.21
4.536
4.06
0.160
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
131
5.2
125
4.9210
120.22
4.733
4.06
0.160
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
136
5.4
130
5.1181
125.22
4.930
4.06
0.160
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
141
5.6
140
5.5118
135.23
5.324
4.90
0.193
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
151
5.9
150
5.9055
145.24
5.718
4.90
0.193
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
161
6.3
160
6.2992
155.22
6.111
4.90
0.193
3.10
0.122
0.6
0.024
2.82
0.111
7.21
0.284
0.28
171
6.7
170
6.6929
163.65
6.443
5.69
0.224
3.50
0.138
0.6
0.024
3.10
0.122
9.60
0.378
10
0.39
184
7.2
180
7.0866
173.66
6.837
5.69
0.224
3.50
0.138
0.6
0.024
3.10
0.122
9.60
0.378
10
0.39
194
7.6
190
7.4803
183.64
7.230
5.69
0.224
3.50
0.138
0.6
0.024
3.10
0.122
9.60
0.378
10
0.39
204
8.0
200
7.8740
193.65
7.624
5.69
0.224
3.50
0.138
0.6
0.024
3.10
0.122
9.60
0.378
10
0.39
214
8.4
Note: Does not include 6000 series bearings
31

Single row
Conrad
Open, sealed, shielded and snap ring
Standard and SKF Explorer
Series: 607 6026
Size: 7 mm 130 mm
0.2756 in 5.1181 in
RS1
RZ
RS1
RZ
2RS1
2Z
2RZ
NR
2RS1
2Z
2RZ
NR
OPEN
Open
Designation
Principal dimensions
Bore
d
mm
in
Outside diameter
D
mm
in
Speed rating1
Sealed
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Static
C0
lbf
lbf
Mass
Reference Limiting Limiting

speed
speed
speed
r/min r/min r/min
kg
lb
607
608
609
7
8
9
0.2756
0.3150
0.3543
19
22
24
0.7480
0.8661
0.9449
6
7
7
0.2362
0.2756
0.2756
2 340
3 450
3 900
530
780
880
950
1 370
1 660
210
310
370
85 000 53 000
75 000 48 000
70 000 43 000
24 000
22 000
19 000
0.01
0.01
0.01
0.02
0.03
0.03
6000
6001
6002
10
12
15
0.3937
0.4724
0.5906
26
28
32
1.0236
1.1024
1.2598
8
8
9
0.3150
0.3150
0.3543
4 750
5 400
5 850
1 070
1 210
1 320
1 960
2 360
2 850
440
530
640
67 000 40 000
60 000 38 000
50 000 32 000
19 000
17 000
14 000
0.02
0.02
0.03
0.04
0.05
0.07
6003
6004
6005
17
20
25
0.6693
0.7874
0.9843
35
42
47
1.3780
1.6535
1.8504
10
12
12
0.3937
0.4724
0.4724
6 370
9 950
11 900
1 430
2 240
2 680
3 250
5 000
6 550
730
1 120
1 470
45 000 28 000
38 000 24 000
32 000 20 000
13 000
11 000
9 500
0.04
0.07
0.08
0.09
0.15
0.18
6006
6007
6008
30
35
40
1.1811
1.3780
1.5748
55
62
68
2.1654
2.4409
2.6772
13
14
15
0.5118
0.5512
0.5906
13 800
16 800
17 800
3 100
3 780
4 000
8 300
10 200
11 600
1 870
2 290
2 610
28 000 17 000
24 000 15 000
22 000 14 000
8 000
7 000
6 300
0.12
0.16
0.19
0.26
0.35
0.42
6009
6010
6011
45
50
55
1.7717
1.9685
2.1654
75
80
90
2.9528
3.1496
3.5433
16
16
18
0.6299
0.6299
0.7087
22 100
22 900
29 600
4 970
5 150
6 650
14 600
16 000
21 200
3 280
3 600
4 770
20 000 12 000
18 000 11 000
16 000 10 000
5 600
5 000
4 500
0.25
0.26
0.39
0.55
0.57
0.86
6012
6013
6014
60
65
70
2.3622
2.5591
2.7559
95
100
110
3.7402
3.9370
4.3307
18
18
20
0.7087
0.7087
0.7874
30 700
31 900
39 700
6 900
7 170
8 920
23 200
25 000
31 000
5 220
5 620
6 970
15 000
14 000
13 000
9 500
9 000
8 000
4 300
4 000
3 600
0.42
0.44
0.60
0.93
0.97
1.32
6015
6016
6017
75
80
85
2.9528
3.1496
3.3465
115
125
130
4.5276
4.9213
5.1181
20
22
22
0.7874
0.8661
0.8661
41 600
49 400
52 000
9 350
11 110
11 690
33 500
40 000
43 000
7 530
8 990
9 670
12 000
11 000
11 000
7 500
7 000
6 700
3 400
3 200
3 000
0.64
0.85
0.89
1.41
1.87
1.96
6018
6019
6020
90
95
100
3.5433
3.7402
3.9370
140
145
150
5.5118
5.7087
5.9055
24
24
24
0.9449
0.9449
0.9449
60 500
63 700
63 700
13 600
14 320
14 320
50 000
54 000
54 000
11 240
12 140
12 140
10 000
9 500
9 500
6 300
6 000
5 600
2 800
2 800
2 600
1.15
1.20
1.25
2.54
2.65
2.76
6021
6022
6024
105
110
120
4.1339
4.3307
4.7244
160
170
180
6.2992
6.6929
7.0866
26
28
28
1.0236
1.1024
1.1024
76 100
85 200
88 400
17 110
19 200
19 900
65 500
73 500
80 000
14 720
16 520
17 980
8 500
8 000
7 500
5 300
5 000
4 800
2 400
2 400
3 400
1.60
1.95
2.05
3.53
4.30
4.52
6026
130
5.1181
200
7.8740
33
1.2992
112 000
25 200
100 000
22 500
7 000
4 300
2 000
3.15
6.9
For shielded limiting speed ratings, contact SKF Applications Engineering.
Warning: The new reference and limiting speeds are not to be used as a direct substitution for the previous oil and grease speed ratings. See page 7 for details.
Consult SKF USA Inc. prior to design change or order placement.
32
Single row
Conrad
Standard
Series: 6028 60/800 N1MAS
Size: 140 mm 800 mm
5.5118 in 31.4960 in
RS1
RS1*
Z*
2RS1
2Z
2RS1*
OPEN
Open
Designation
2Z*
Bore
d
Outside diameter
D
mm
in
Speed rating1
Sealed
Basic load ratings

Width
B
mm
in
mm
in
6028
6030
6032
140
150
160
5.5118
5.9055
6.2992
210
225
240
8.2677
8.8583
9.4488
33
35
38
1.2992
1.3780
1.4961
6034 M
6036 M
6038 M
170
180
190
6.6929
7.0866
7.4803
260
280
290
10.2362
11.0236
11.4173
42
46
46
6040 M
6044 M
6048 M
200
220
240
7.8740
8.6614
9.4488
310
340
360
12.2047
13.3858
14.1732
6052 M
6056 M
6060 M
260
280
300
10.2362
11.0236
11.8110
400
420
460
6064 M
6068 M
6072 M
320
340
360
12.5984
13.3858
14.1732
6076 M
6080 M
6084 M
380
400
420
6088 M
6092 MB
6096 MB
Dynamic
C
N
Static
C0

speed
speed
speed
r/min r/min r/min
lbf
lbf
111 000
125 000
143 000
25 000
28 100
32 200
108 000
125 000
143 000
24 300
28 100
32 200
6 700
6 000
5 600
4 000
3 800
3 600
1.6535
1.8110
1.8110
168 000
190 000
195 000
37 800
42 800
43 900
173 000
200 000
216 000
38 900
45 000
48 600
5 300
4 800
4 800
51
56
56
2.0079
2.2047
2.2047
216 000
247 000
255 000
48 600
55 600
57 400
245 000
290 000
315 000
55 100
65 200
70 900
15.7480
16.5354
18.1102
65
65
74
2.5591
2.5591
2.9134
291 000
302 000
358 000
65 500
67 900
80 500
480
520
540
18.8976
20.4724
21.2598
74
82
82
2.9134
3.2283
3.2283
371 000
423 000
462 000
14.9606
15.7480
16.5354
560
600
620
22.0472
23.6220
24.4094
82
90
90
3.2283
3.5433
3.5433
440
460
480
17.3228
18.1102
18.8976
650
680
700
25.5906
26.7717
27.5591
94
100
100
60/500 N1MAS
60/560 N1MAS
60/630 N1MBS
500
560
630
19.6850
22.0472
24.8031
720
820
920
28.3465
32.2835
36.2205
60/670 N1MAS
60/800 N1MAS
670
800
26.3780
31.4960
980
1150
38.5827
45.2755
Mass
kg
lb
1 800
1 700
1 600
3.35
4.80
5.90
7.40
10.60
13.00
4 300
4 000
3 800
7.90
10.50
11.00
17.42
23.10
24.25
4 300
4 000
3 600
3 600
3 200
3 000
14.00
18.50
19.50
30.90
40.80
43.00
375 000
84 300
405 000
91 100
500 000 112 400
3 200
3 000
2 800
2 800
2 600
2 400
29.50
31.00
44.00
65.00
68.30
97.00
83 500
95 100
103 900
540 000 121 400

640 000 143 900
735 000 165 300
2 600
2 400
2 400
2 200
2 200
1 900
46.00
62.00
64.50
101.40
136.70
142.20
462 000
520 000
507 000
103 900
116 900
114 000
750 000 168 600

865 000 194 500
880 000 197 900
2 200
2 000
2 000
1 800
1 700
1 600
67.50
87.50
91.50
148.80
192.90
201.70
3.7008
3.9370
3.9370
553 000
582 000
618 000
124 400
130 900
139 000
965 000 217 000

1 060 000 238 300
1 140 000 256 300
1 900
1 800
1 700
1 500
1 500
1 400
105.00
120.00
125.00
230.00
260.00
280.00
100
115
128
3.9370
4.5276
5.0394
605 000
663 000
819 000
136 100
149 100
184 200
1 140 000 256 300

1 470 000 330 500
1 760 000 395 700
1 600
1 400
1 200
1 300
1 200
1 000
135.00
210.00
285.00
300.00
460.00
630.00
136
155
5.3543
6.1024
904 000
1 010 000
203 300
227 100
2 040 000 458 600

2 550 000 573 300
1 100
900
900
750
345.00 760.00
535.00 1180.00
* Feature may not be available in all sizes.

1
33

Single row
Conrad
Series: 623 6224
Size: 3 mm 120 mm
0.1181 in 4.7244 in
RS1
RS1
2RS1
2Z
NR
2RS1
2Z
NR
OPEN
Open
Designation
Bore
d
Speed rating1
Sealed
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
N
Static
C0
lbf
lbf
Mass

speed
speed
speed
r/min
r/min
r/min
kg
lb
mm
in
623
624
625
3
4
5
0.1181
0.1575
0.1969
10
13
16
0.3937
0.5118
0.6299
4
5
5
0.1575
0.1969
0.1969
540
936
1 140
120
210
260
180
290
380
40
70
90
130 000 80 000

110 000 67 000
95 000 60 000
40 000
0.01
0.01
0.01
0.01
0.01
0.02
626
627
629
6
7
9
0.2362
0.2756
0.3543
19
22
26
0.7480
0.8661
1.0236
6
7
8
0.2362
0.2756
0.3150
2 340
3 450
4 750
530
780
1 070
950
1 370
1 960
210
310
440
80 000 50 000
70 000 45 000
60 000 38 000
24 000
22 000
19 000
0.01
0.01
0.02
0.02
0.03
0.05
6200
6201
6202
10
12
15
0.3937
0.4724
0.5906
30
32
35
1.1811
1.2598
1.3780
9
10
11
0.3543
0.3937
0.4331
5 400
7 280
8 060
1 220
1 700
1 800
2 360
3 100
3 750
530
700
840
56 000 34 000
50 000 32 000
43 000 28 000
17 000
15 000
13 000
0.03
0.04
0.05
0.08
0.09
0.10
6203
6204
6205
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
12
14
15
0.4724
0.5512
0.5906
9 950
13 500
14 800
2 200
3 000
3 300
4 750
6 550
7 800
1 100
1 500
1 800
38 000 24 000
32 000 20 000
28 000 18 000
12 000
10 000
8 500
0.07
0.11
0.13
0.15
0.20
0.30
6206
6207
6208
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409
2.8346
3.1496
16
17
18
0.6299
0.6693
0.7087
20 300
27 000
32 500
4 600
6 100
7 300
11 200
15 300
19 000
2 500
3 400
4 300
24 000 15 000
20 000 13 000
18 000 11 000
7 500
6 300
5 600
0.20
0.29
0.37
0.40
0.60
0.80
6209
6210
6211
45
50
55
1.7717
1.9685
2.1654
85
90
100
3.3465
3.5433
3.9370
19
20
21
0.7480
0.7874
0.8268
35 100
37 100
46 200
7 900
8 300
10 400
21 600
23 200
29 000
4 900
5 200
6 500
17 000 11 000
15 000 10 000
14 000 9 000
5 000
4 800
4 300
0.41
0.46
0.61
0.90
1.00
1.30
6212
6213
6214
60
65
70
2.3622
2.5591
2.7559
110
120
125
4.3307
4.7244
4.9213
22
23
24
0.8661
0.9055
0.9449
55 300
58 500
63 700
12 400
13 200
14 300
36 000
40 500
45 000
8 100
9 100
10 100
13 000
12 000
11 000
8 000
7 500
7 000
4 000
3 600
3 400
0.78
0.99
1.05
1.70
2.20
2.30
6215
6216
6217
75
80
85
2.9528
3.1496
3.3465
130
140
150
5.1181
5.5118
5.9055
25
26
28
0.9843
1.0236
1.1024
68 900
72 800
87 100
15 500
16 400
19 600
49 000
55 000
64 000
11 000
12 400
14 400
10 000
9 500
9 000
6 700
6 000
5 600
3 200
3 000
2 800
1.20
1.40
1.80
2.60
3.10
4.00
6218
6219
6220
90
95
100
3.5433
3.7402
3.9370
160
170
180
6.2992
6.6929
7.0866
30
32
34
1.1811
1.2598
1.3386
101 000
114 000
127 000
22 700
25 600
28 500
73 500
81 500
93 000
16 500
18 300
20 900
8 500
8 000
7 500
5 300
5 000
4 800
2 600
2 400
2 400
2.15
2.60
3.15
4.70
5.70
6.90
6221
6222
6224
105
110
120
4.1339
4.3307
4.7244
190
200
215
7.4803
7.8740
8.4646
36
38
40
1.4173
1.4961
1.5748
140 000
151 000
146 000
31 500
33 900
32 800
104 000
118 000
118 000
23 400
26 500
26 500
7 000
6 700
6 300
4 500
4 300
4 000
2 200
3.70
4.35
5.15
8.20
9.60
11.40
34
Single row
Conrad
Open and shielded
Standard
Series: 6226 6256 M
Size: 130 mm 280 mm
5.1181 in 11.0236 in
2Z
2Z
OPEN
Open
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
lbf
lbf
1.5748
1.6535
1.7717
156 000
165 000
174 000
35 100
37 100
39 100
132 000
150 000
166 000
29 700
33 700
37 300
5 600
5 300
5 000
3 600
3 400
3 200
5.80
7.45
9.40
12.80
16.40
20.70
48
52
52
1.8898
2.0472
2.0472
186 000
212 000
229 000
41 800
47 700
51 500
186 000
224 000
240 000
41 800
50 400
54 000
4 500
4 300
4 000
3 000
3 800
3 600
14.50
17.50
18.50
32.00
38.60
40.80
13.3858
14.1732
15.7480
55
58
65
2.1654
2.2835
2.5591
255 000
270 000
296 000
57 300
60 700
66 500
280 000
310 000
365 000
62 900
69 700
82 100
3 800
3 600
3 200
3 400
3 200
3 000
23.00
28.00
37.00
50.70
61.70
81.60
17.3228
18.8976
19.6850
72
80
80
2.8346
3.1496
3.1496
358 000
390 000
423 000
80 500
87 700
95 100
465 000
530 000
600 000
104 500
119 100
134 900
3 000
2 600
2 600
2 600
2 400
2 200
51.00
65.50
71.00
112.40
144.40
156.50
in
6226
6228
6230
130
140
150
5.1181
5.5118
5.9055
230
250
270
9.0551
9.8425
10.6299
40
42
45
6232
6234 M
6236 M
160
170
180
6.2992
6.6929
7.0866
290
310
320
11.4173
12.2047
12.5984
6238 M
6240 M
6244 M
190
200
220
7.4803
7.8740
8.6614
340
360
400
6248 M
6252 M
6256 M
240
260
280
9.4488
10.2362
11.0236
440
480
500
Static
C0
Mass
Reference
speed
r/min
mm
Dynamic
C
Speed rating
Limiting
speed
r/min
kg
lb
35

Single row
Conrad
Series: 634 6332 M
Size: 4 mm 160 mm
0.1575 in 6.2992 in
RS1
RZ
RS1
RZ
2RS1
2Z
2RZ
NR
2RS1
2Z
2RZ
NR
OPEN
Open
Designation
Bore
d
Speed rating1
Sealed
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
N
Static
C0
lbf
lbf
Mass

speed
speed
speed
r/min r/min r/min
kg
lb
mm
in
634
635
6300
4
5
10
0.1575
0.1969
0.3937
16
19
35
0.6299
0.7480
1.3780
5
6
11
0.1969
0.2362
0.4331
1 110
2 340
8 520
200
500
1 900
380
950
3 400
100
200
800
95 000 60 000
80 000 50 000
50 000 32 000
28 000
24 000
15 000
0.01
0.01
0.05
0.10
0.10
0.10
6301
6302
6303
12
15
17
0.4724
0.5906
0.6693
37
42
47
1.4567
1.6535
1.8504
12
13
14
0.4724
0.5118
0.5512
10 100
11 900
14 300
2 300
2 700
3 200
4 150
5 400
6 550
900
1 200
1 500
45 000 28 000
38 000 24 000
34 000 22 000
14 000
12 000
11 000
0.06
0.08
0.12
0.10
0.20
0.30
6304
6305
6306
20
25
30
0.7874
0.9843
1.1811
52
62
72
2.0472
2.4409
2.8346
15
17
19
0.5906
0.6693
0.7480
16 800
23 400
29 600
3 800
5 300
6 700
7 800
11 600
16 000
1 800
2 600
3 600
30 000 19 000
24 000 16 000
20 000 13 000
9 500
7 500
6 300
0.14
0.23
0.35
0.30
0.50
0.80
6307
6308
6309
35
40
45
1.3780
1.5748
1.7717
80
90
100
3.1496
3.5433
3.9370
21
23
25
0.8268
0.9055
0.9843
35 100
42 300
55 300
7 900
9 500
12 400
19 000
24 000
31 500
4 300
5 400
7 100
19 000 12 000
17 000 11 000
15 000 9 500
6 000
5 000
4 500
0.46
0.63
0.83
1.00
1.40
1.80
6310
6311
6312
50
55
60
1.9685
2.1654
2.3622
110
120
130
4.3307
4.7244
5.1181
27
29
31
1.0630
1.1417
1.2205
65 000
74 100
85 200
14 600
16 700
19 200
38 000
45 000
52 000
8 500
10 100
11 700
13 000
12 000
11 000
8 500
8 000
7 000
4 300
3 800
3 400
1.05
1.35
1.70
2.30
3.00
3.70
6313
6314
6315
65
70
75
2.5591
2.7559
2.9528
140
150
160
5.5118
5.9055
6.2992
33
35
37
1.2992
1.3780
1.4567
97 500
111 000
119 000
21 900
25 000
26 800
60 000
68 000
76 500
13 500
15 300
17 200
10 000
9 500
9 000
6 700
6 300
5 600
3 200
3 000
2 800
2.10
2.50
3.00
4.60
5.50
6.60
6316
6317
6318
80
85
90
3.1496
3.3465
3.5433
170
180
190
6.6929
7.0866
7.4803
39
41
43
1.5354
1.6142
1.6929
130 000
140 000
151 000
29 200
31 500
33 900
86 500
96 500
108 000
19 400
21 700
24 300
8 500
8 000
7 500
5 300
5 000
4 800
2 600
2 400
2 400
3.60
4.25
4.90
7.90
9.40
10.80
6319
6320
6321
95
100
105
3.7402
3.9370
4.1339
200
215
225
7.8740
8.4646
8.8583
45
47
49
1.7717
1.8504
1.9291
159 000
174 000
182 000
35 700
39 100
40 900
118 000
140 000
153 000
26 500
31 500
34 400
7 000
6 700
6 300
4 500
4 300
4 000
2 200
5.65
7.00
8.25
12.50
15.40
18.20
6322
6324
6326 M
110
120
130
4.3307
4.7244
5.1181
240
260
280
9.4488
10.2362
11.0236
50
55
58
1.9685
2.1654
2.2835
203 000
208 000
229 000
45 600
46 800
51 500
180 000
186 000
216 000
40 500
41 800
48 600
6 000
5 600
5 000
3 800
3 400
3 200
9.55
12.50
17.50
21.10
27.60
38.60
6328 M
6330 M
6332 M
140
150
160
5.5118
5.9055
6.2992
300
320
340
11.8110
12.5984
13.3858
62
65
68
2.4409
2.5591
2.6772
251 000
276 000
276 000
56 400
62 000
62 000
245 000
285 000
285 000
55 100
64 100
64 100
4 800
4 300
4 000
4 300
4 000
3 800
22.00
26.00
29.00
48.50
57.30
63.90
36
Single row
Conrad
Open
Series: 6334 M 6348 M
Standard
Size: 170 mm 240 mm
6.6929 in 9.4488 in
OPEN
Open
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
Speed rating
Static
C0
lbf
lbf
Reference
speed
r/min
Mass
Limiting
speed
r/min
kg
lb
6334 M
6336 M
6338 M
170
180
190
6.6929
7.0866
7.4803
360
380
400
14.1732
14.9606
15.7480
72
75
78
2.8346
2.9528
3.0709
312 000
351 000
371 000
70 100
78 900
83 400
340 000
405 000
430 000
76 400
91 000
96 700
3 800
3 600
3 400
3 400
3 200
3 000
34.50
42.50
49.00
76.10
93.70
108.00
6344 M
6348 M
220
240
8.6614
9.4488
460
500
18.1102
19.6850
88
95
3.4646
3.7401
410 000
442 000
92 200
99 400
520 000
585 000
116 900
131 500
3 000
2 600
2 600
2 400
72.50
92.50
159.80
203.90
37

Single row
Conrad
Open and snap ring
Standard
Series: 6403 6420
Size: 17 mm 100 mm
0.6693 in 3.9370 in
NR
NR
OPEN
Open
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
Dynamic
C
Speed rating
Static
C0
mm
in
lbf
lbf
Mass
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
6403
6404
6405
17
20
25
0.6693
0.7874
0.9843
62
72
80
2.4409
2.8346
3.1496
17
19
21
0.6693
0.7480
0.8268
22 900
30 700
35 800
5 100
6 900
8 000
10 800
15 000
19 300
2 400
3 400
4 300
28 000
24 000
20 000
18 000
15 000
13 000
0.27
0.40
0.53
0.60
0.90
1.20
6406
6407
6408
30
35
40
1.1811
1.3780
1.5748
90
100
110
3.5433
3.9370
4.3307
23
25
27
0.9055
0.9843
1.0630
43 600
55 300
63 700
9 800
12 400
14 300
23 600
31 000
36 500
5 300
7 000
8 200
18 000
16 000
14 000
11 000
10 000
9 000
0.74
0.95
1.25
1.60
2.10
2.80
6409
6410
6411
45
50
55
1.7717
1.9685
2.1654
120
130
140
4.7244
5.1181
5.5118
29
31
33
1.1417
1.2205
1.2992
76 100
87 100
99 500
17 100
19 600
22 400
45 000
52 000
62 000
10 100
11 700
13 900
13 000
12 000
11 000
8 500
7 500
7 000
1.55
1.90
2.30
3.40
4.20
5.10
6412
6413
6414
60
65
70
2.3622
2.5591
2.7559
150
160
180
5.9055
6.2992
7.0866
35
37
42
1.3780
1.4567
1.6535
108 000
119 000
143 000
24 300
26 800
32 100
69 500
78 000
104 000
15 600
17 500
23 400
10 000
9 500
8 500
6 300
6 000
5 300
2.75
3.30
4.85
6.10
7.30
10.70
6415
6416
6417
75
80
85
2.9528
3.1496
3.3465
190
200
210
7.4803
7.8740
8.2677
45
48
52
1.7717
1.8898
2.0472
153 000
163 000
174 000
34 400
36 600
39 100
114 000
125 000
137 000
25 600
28 100
30 800
8 000
7 500
7 000
5 000
4 800
4 500
6.80
8.00
9.50
15.00
17.60
20.90
6418
90
3.5433
225
8.8583
54
2.1260
186 000
41 800
150 000
33 700
6 700
4 300
11.50
25.40
6420
100
3.9370
250
9.8425
58
2.2835
208 000
46 800
176 000
39 600
6 000
4 000
15.30
33.70
38
Single row
Conrad
Open, shielded and snap ring
Series: 16002 16040
Size: 15 mm 200 mm
0.5906 in 7.8740 in
2Z
NR
2Z*
NR*
OPEN
Open
Designation
Bore
d
Outside diameter
D
mm
in
Speed rating1
Basic load ratings

Width
B
mm
in
mm
in
16002
16003
16004
15
17
20
0.5906
0.6693
0.7874
32
35
42
1.2598
1.3780
1.6535
8
8
8
0.3150
0.3150
0.3150
16005
16006
16007
25
30
35
0.9843
1.1811
1.3780
47
55
62
1.8504
2.1654
2.4409
8
9
9
16008
16009
16010
40
45
50
1.5748
1.7717
1.9685
68
75
80
2.6772
2.9528
3.1496
16011
16012
16013
55
60
65
2.1654
2.3622
2.5591
90
95
100
16014
16015
16016
70
75
80
2.7559
2.9528
3.1496
16017
16018
16019
85
90
95
16020
16021
16022
Dynamic
C
N
Static
C0
lbf
Reference
speed
r/min
Limiting
speed
r/min
lbf
5 850
6 370
7 280
1 300
1 400
1 600
2 850
3 250
4 050
600
700
900
50 000
45 000
38 000
0.3150
0.3543
0.3543
8 060
11 900
13 000
1 800
2 700
2 900
4 750
7 350
8 150
1 100
1 700
1 800
9
10
10
0.3543
0.3937
0.3937
13 800
16 500
16 800
3 100
3 700
3 800
9 150
10 800
11 400
3.5433
3.7402
3.9370
11
11
11
0.4331
0.4331
0.4331
20 300
20 800
22 500
4 600
4 700
5 100
110
115
125
4.3307
4.5276
4.9213
13
13
14
0.5118
0.5118
0.5512
29 100
30 200
35 100
3.3465
3.5433
3.7402
130
140
145
5.1181
5.5118
5.7087
14
16
16
0.5512
0.6299
0.6299
100
105
110
3.9370
4.1339
4.3307
150
160
170
5.9055
6.2992
6.6929
16
18
19
16024
16026
16028
120
130
140
4.7244
5.1181
5.5118
180
200
210
7.0866
7.8740
8.2677
16030
16032
16034
150
160
170
5.9055
6.2992
6.6929
225
240
260
16036
16038
16040
180
190
200
7.0866
7.4803
7.8740
280
290
310
Mass
kg
lb
32 000
28 000
24 000
0.03
0.03
0.05
0.06
0.07
0.11
32 000
28 000
24 000
20 000
17 000
15 000
0.06
0.09
0.11
0.10
0.19
0.24
2 100
2 400
2 600
22 000
20 000
18 000
14 000
12 000
11 000
0.13
0.17
0.18
0.29
0.37
0.40
14 000
15 000
16 600
3 100
3 400
3 700
16 000
15 000
14 000
10 000
9 500
9 000
0.26
0.28
0.30
0.57
0.62
0.66
6 500
6 800
7 900
25 000
27 000
31 500
5 600
6 100
7 100
13 000
12 000
11 000
8 000
7 500
7 000
0.43
0.46
0.60
0.90
1.00
1.30
35 800
43 600
44 800
8 000
9 800
10 100
33 500
39 000
41 500
7 500
8 800
9 300
11 000
10 000
9 500
6 700
6 300
6 000
0.63
0.85
0.89
1.40
1.90
2.00
0.6299
0.7087
0.7480
46 200
54 000
60 200
10 400
12 100
13 500
44 000
51 000
57 000
9 900
11 500
12 800
9 500
8 500
8 000
5 600
5 300
5 000
0.91
1.20
1.45
2.00
2.65
3.20
19
22
22
0.7480
0.8661
0.8661
63 700
83 200
80 600
14 300
18 700
18 100
64 000
81 500
86 500
14 400
18 300
19 400
7 500
7 000
6 700
4 800
4 300
4 000
1.60
2.35
2.50
3.50
5.20
5.50
8.8583
9.4488
10.2362
24
25
28
0.9449
0.9843
1.1024
92 200
99 500
119 000
20 700
22 400
26 800
98 000
108 000
129 000
22 000
24 300
29 000
6 000
5 600
5 300
3 800
3 600
3 200
3.15
3.70
5.00
6.90
8.20
11.00
11.0236
11.4173
12.2047
31
31
34
1.2205
1.2205
1.3386
138 000
148 000
168 000
31 000
33 300
37 800
146 000
166 000
190 000
32 800
37 300
42 700
4 800
4 800
4 300
4 000
3 000
2 800
6.60
7.90
8.85
14.60
17.40
19.50

1
39

Single row
Conrad
Open and sealed
Standard
Series: 16044 16072
Size: 220 mm 360 mm
8.6614 in 14.1732 in
RS1
RZ
RS1
RZ
Series: 16100 16101

Size: 10 mm 12 mm
0.3937 in 0.4724 in
OPEN
Open
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
2RZ
2RZ
Speed rating
Sealed
Static
C0
lbf
2RS1
2RS1

speed
speed
speed
r/min r/min r/min
mm
in
16044
16048
16052
220
240
260
8.6614
9.4488
10.2362
340
360
400
13.3858
14.1732
15.7480
37
37
44
1.4567
1.4567
1.7323
174 000
178 000
238 000
39 100
40 000
53 500
204 000
220 000
310 000
45 900
49 500
69 700
4 000
3 600
3 200
2 400
3 000
2 800
16056
16060
16064
280
300
320
11.0236
11.8110
12.5984
420
460
480
16.5354
18.1102
18.8976
44
50
50
1.7323
1.9685
1.9685
242 000
286 000
281 000
54 400
64 300
63 200
335 000
405 000
405 000
75 300
91 000
91 000
3 000
2 800
2 600
16068
16072
340
360
13.3858
14.1732
520
540
20.4724
21.2598
57
57
2.2441
2.2441
345 000
351 000
77 600
78 900
520 000 116 900

550 000 123 600
2 400
2 400
16100
16101
10
12
0.3937
0.4724
28
30
1.1024
1.1811
8
8
0.3150
0.3150
4 620
5 070
1 000
1 100
1 960
2 360
lbf
400
500
Mass
kg
lb
11.50
14.50
21.50
25.40
32.00
47.40
2 600
2 400
2 200
23.00
32.00
34.00
50.70
70.50
75.00
2 000
1 900
45.00
49.00
99.20
108.00
63 000 40 000
56 000 34 000
16 000
0.02
0.02
0.05
0.05
40
Single row
Conrad
Standard
Series: 61800 61826
Size: 10 mm 130 mm
0.3937 in 5.1181 in
RS1
RZ
RS1
RZ
2RS1
2Z
2RZ
NR
2RS1
2Z
2RZ
NR
OPEN
Open
Designation
Bore
d
Outside diameter
D
mm
in
Speed rating1
Sealed
Basic load ratings

Width
B
mm
in
mm
in
61800
61801
61802
10
12
15
0.3937
0.4724
0.5906
19
21
24
0.7480
0.8268
0.9449
5
5
5
61803
61804
61805
17
20
25
0.6693
0.7874
0.9843
26
32
37
1.0236
1.2598
1.4567
61806
61807
61808
30
35
40
1.1811
1.3780
1.5748
42
47
52
61809
61810
61811
45
50
55
1.7717
1.9685
2.1654
61812
61813
61814
60
65
70
61815
61816
61817
Dynamic
C
Static
C0
N
lbf
Mass

speed
speed
speed
r/min r/min r/min
kg
lb
lbf
0.1969
0.1969
0.1969
1 380
1 430
1 560
300
300
400
585
670
800
100
200
200
80 000 48 000
70 000 43 000
60 000 38 000
22 000
20 000
17 000
0.01
0.01
0.01
0.01
0.01
0.02
5
7
7
0.1969
0.2756
0.2756
1 680
4 030
4 360
400
900
1 000
930
2 320
2 600
200
500
600
56 000 34 000
45 000 28 000
38 000 24 000
16 000
13 000
11 000
0.01
0.02
0.02
0.02
0.04
0.05
1.6535
1.8504
2.0472
7
7
7
0.2756
0.2756
0.2756
4 490
4 750
4 940
1 000
1 100
1 100
2 900
3 200
3 450
700
700
800
32 000 20 000
28 000 18 000
26 000 16 000
9 500
8 000
7 500
0.03
0.03
0.03
0.06
0.07
0.07
58
65
72
2.2835
2.5591
2.8346
7
7
9
0.2756
0.2756
0.3543
6 630
6 760
9 040
1 500
1 500
2 000
6 100
6 800
8 800
1 400
1 500
2 000
22 000 14 000
20 000 13 000
19 000 12 000
6 700
6 000
5 300
0.04
0.05
0.08
0.09
0.10
0.20
2.3622
2.5591
2.7559
78
85
90
3.0709
3.3465
3.5433
10
10
10
0.3937
0.3937
0.3937
11 900
12 400
12 400
2 700
2 800
2 800
11 400
12 700
13 200
2 600
2 900
3 000
17 000 11 000
16 000 10 000
15 000 9 000
4 800
4 500
4 300
0.11
0.13
0.14
0.20
0.30
0.30
75
80
85
2.9528
3.1496
3.3465
95
100
110
3.7402
3.9370
4.3307
10
10
13
0.3937
0.3937
0.5118
12 700
13 000
19 500
2 900
2 900
4 400
14 300
15 000
20 800
3 200
3 400
4 700
14 000
13 000
12 000
8 500
8 000
7 500
4 000
3 600
3 400
0.15
0.15
0.27
0.30
0.30
0.60
61818
61820
61821
90
100
105
3.5433
3.9370
4.1339
115
125
130
4.5276
4.9213
5.1181
13
13
13
0.5118
0.5118
0.5118
19 500
19 900
20 800
4 400
4 500
4 700
22 000
24 000
19 600
4 900
5 400
4 400
11 000
10 000
10 000
7 000
6 300
6 300
3 200
3 000
2 800
0.28
0.31
0.32
0.60
0.70
0.70
61822
61824
61826
110
120
130
4.3307
4.7244
5.1181
140
150
165
5.5118
5.9055
6.4961
16
16
18
0.6299
0.6299
0.7087
28 100
29 100
37 700
6 300
6 500
8 500
26 000
28 000
43 000
5 800
6 300
9 700
9 500
8 500
8 000
5 600
5 300
4 800
2 600
2 400
2 200
0.60
0.65
0.93
1.30
1.40
2.10
* 61808-2RZ NR and 61812 NR are made to order products.

1
41

Single row
Conrad
Open and sealed
Standard
Series: 61828 618/800 MA
Size: 140 mm 800 mm
5.5118 in 31.4961 in
RS1
RZ
RS1*
RZ*
2RS1
2RS1*
OPEN
Open
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Sealed
Static
C0
lbf
2RZ
2RZ*
lbf

speed
speed
speed
r/min r/min r/min
mm
in
61828
61830
61832
140
150
160
5.5118
5.9055
6.2992
175
190
200
6.8898
7.4803
7.8740
18
20
20
0.7087
0.7874
0.7874
39 000
48 800
49 400
8 800
11 000
11 100
46 500
61 000
64 000
10 500
13 700
14 400
7 500
6 700
6 300
4 500
4 300
4 000
61834
61836
61838
170
180
190
6.6929
7.0866
7.4803
215
225
240
8.4646
8.8583
9.4488
22
22
24
0.8661
0.8661
0.9449
61 800
62 400
76 100
13 900
14 000
17 100
78 000
81 500
98 000
17 500
18 300
22 000
6 000
5 600
5 300
61840
61844
61848
200
220
240
7.8740
8.6614
9.4488
250
270
300
9.8425
10.6299
11.8110
24
24
28
0.9449
0.9449
1.1024
76 100
78 000
108 000
17 100
17 500
24 300
102 000
110 000
150 000
22 900
24 700
33 700
61852
61856
61860 MA
260
280
300
10.2362
11.0236
11.8110
320
350
380
12.5984
13.7795
14.9606
28
33
38
1.1024
1.2992
1.4961
111 000
138 000
172 000
25 000
31 000
38 700
163 000
200 000
245 000
61864 MA
61868 MA
61872 MA
320
340
360
12.5984
13.3858
14.1732
400
420
440
15.7480
16.5354
17.3228
38
38
38
1.4961
1.4961
1.4961
172 000
178 000
182 000
38 700
40 000
40 900
61876 MA
61880 MA
61884 MA
380
400
420
14.9606
15.7480
16.5354
480
500
520
18.8976
19.6850
20.4724
46
46
46
1.8110
1.8110
1.8110
242 000
247 000
251 000
61888 MA
61892 MA
61896 MA
440
460
480
17.3228
18.1102
18.8976
540
580
600
21.2598
22.8346
23.6220
46
56
56
1.8110
2.2047
2.2047
618/500 MA
618/530 MA
618/560 MA
500
530
560
19.6850
20.8661
22.0472
620
650
680
24.4094
25.5906
26.7717
56
56
56
618/600 MA
618/630 MA
618/670 MA
600
630
670
23.6220
24.8031
26.3780
730
780
820
28.7402
30.7087
32.2835
618/710 MA
618/750 MA
618/800 MA
710
750
800
27.9528
29.5276
31.4961
870
920
980
34.2520
36.2205
38.5827
kg
lb
2 000
0.99
1.40
1.45
2.20
3.10
3.20
3 600
3 400
3 200
1.90
2.00
2.60
4.20
4.40
5.70
5 000
4 500
4 000
3 200
2 800
2 600
2.70
3.00
4.50
6.00
6.60
9.90
36 600
45 000
55 100
3 800
3 400
3 200
2 400
2 200
2 600
4.80
7.40
10.50
10.60
16.30
23.10
255 000
275 000
285 000
57 300
61 800
64 100
3 000
2 800
2 600
2 400
2 400
2 200
11.00
11.50
12.00
24.30
25.40
26.50
54 400
55 500
56 400
390 000
405 000
425 000
87 700
91 000
95 500
2 400
2 400
2 200
2 000
1 900
1 800
20.00
20.50
21.50
44.10
45.20
47.40
255 000
319 000
325 000
57 300
71 700
73 100
440 000
98 900
570 000 128 100
600 000 134 900
2 200
2 000
1 900
1 800
1 600
1 600
22.50
35.00
36.50
49.60
77.20
80.50
2.2047
2.2047
2.2047
332 000
332 000
345 000
74 600
74 600
77 600
620 000 139 400

655 000 147 200
695 000 156 200
1 800
1 700
1 600
1 500
1 400
1 300
40.50
39.50
42.00
89.30
87.10
92.60
60
69
69
2.3622
2.7165
2.7165
364 000
442 000
442 000
81 800
99 400
99 400
765 000 172 000

965 000 216 900
1 000 000 224 800
1 500
1 400
1 300
1 200
1 100
1 100
52.00
73.00
83.50
114.60
160.90
184.10
74
78
82
2.9134
3.0709
3.2283
475 000
527 000
559 000
106 800
118 500
125 700
1 100 000 247 300

1 250 000 281 000
1 370 000 308 000
1 200
1 100
1 000
1 000
900
850
93.50
110.00
130.00
206.10
242.50
286.60
42
Mass
Single row
Conrad
Open
Standard
Series: 618/850 MA 618/1180 MA
Size: 850 mm 1180 mm
33.4646 in 46.4566 in
OPEN
Open
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
Dynamic
C
Speed rating
Static
C0
in
lbf
Mass
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
618/850 MA
850
618/900 MA
900
618/1000 MA 1 000
33.4646
35.4331
39.3701
1 030
1 090
1 220
40.5512
42.9134
48.0315
82
85
100
3.2283
3.3465
3.9370
559 000
618 000
637 000
125 700
138 900
143 200
1 430 000
1 600 000
1 800 000
321 500
359 700
404 600
950
850
750
750
700
600
140.00
160.00
245.00
308.60
352.70
540.10
618/1060 MA 1 060
618/1120 MA 1 120
618/1180 MA 1 180
41.7323
44.0944
46.4566
1 280
1 360
1 540
50.3937
53.5433
60.6299
100
106
160
3.9370
4.1732
6.2992
728 000
741 000
761 000
163 700
166 600
171 100
2 120 000
2 200 000
2 360 000
476 600
494 600
530 500
670
630
560
560
530
480
260.00
315.00
330.00
573.20
694.40
727.50
43

Single row
Conrad
Open, sealed and shielded
Standard
Series: 61900 61948 MA
Size: 10 mm 240 mm
0.3937 in 9.4488 in
RS1
RZ
RS1*
Z*
2RS1
Designation
Bore
d
Outside diameter
D
mm
in
Dynamic
C
N
Static
C0
lbf
2Z*
Speed rating1
Sealed
Basic load ratings

Width
B
mm
in
2RZ
2RS1*
OPEN
Open
lbf
Mass

speed
speed
speed
r/min r/min r/min
kg
mm
in
61900
61901
61902
10
12
15
0.3937
0.4724
0.5906
22
24
28
0.8661
0.9449
1.1024
6
6
7
0.2362
0.2362
0.2756
2 080
2 250
4 360
500
500
1 000
850
980
2 240
200
200
500
75 000 45 000
67 000 40 000
56 000 34 000
20 000
19 000
16 000
0.01
0.01
0.02
0.02
0.02
0.04
61903
61904
61905
17
20
25
0.6693
0.7874
0.9843
30
37
42
1.1811
1.4567
1.6535
7
9
9
0.2756
0.3543
0.3543
4 620
6 370
7 020
1 000
1 400
1 600
2 550
3 650
4 300
600
800
1 000
50 000 32 000
43 000 26 000
36 000 22 000
14 000
12 000
10 000
0.02
0.04
0.05
0.04
0.08
0.10
61906
61907
61908
30
35
40
1.1811
1.3780
1.5748
47
55
62
1.8504
2.1654
2.4409
9
10
12
0.3543
0.3937
0.4724
7 280
9 560
13 800
1 600
2 100
3 100
4 550
6 800
10 000
1 000
1 500
2 200
30 000 19 000
26 000 16 000
24 000 14 000
8 500
7 500
6 700
0.05
0.08
0.12
0.11
0.18
0.26
61909
61910
61911
45
50
55
1.7717
1.9685
2.1654
68
72
80
2.6772
2.8346
3.1496
12
12
13
0.4724
0.4724
0.5118
14 000
14 600
16 500
3 100
3 300
3 700
10 800
11 800
14 000
2 400
2 700
3 100
20 000 13 000
19 000 12 000
17 000 11 000
6 000
5 600
5 000
0.14
0.14
0.19
0.31
0.31
0.42
61912
61913
61914
60
65
70
2.3622
2.5591
2.7559
85
90
100
3.3465
3.5433
3.9370
13
13
16
0.5118
0.5118
0.6299
16 500
17 400
23 800
3 700
3 900
5 400
14 300
16 000
21 200
3 200
3 600
4 800
16 000 10 000
15 000 9 500
14 000 8 500
4 500
4 300
4 000
0.20
0.22
0.35
0.44
0.49
0.77
61915
61916
61917
75
80
85
2.9528
3.1496
3.3465
105
110
120
4.1339
4.3307
4.7244
16
16
18
0.6299
0.6299
0.7087
24 200
25 100
31 900
5 400
5 600
7 200
19 300
20 400
30 000
4 300
4 600
6 700
13 000
12 000
11 000
8 000
7 500
7 000
3 600
3 400
0.37
0.40
0.55
0.82
0.88
1.20
61918
61922
61924
90
110
120
3.5433
4.3307
4.7244
125
150
165
4.9213
5.9055
6.4961
18
20
22
0.7087
0.7874
0.8661
33 200
43 600
55 300
7 500
9 800
12 400
31 500
45 000
57 000
7 100
10 100
12 800
11 000
9 000
8 000
6 700
5 600
5 000
0.59
0.90
1.20
1.30
2.00
2.65
61926
61928
61930 MA
130
140
150
5.1181
5.5118
5.9055
180
190
210
7.0866
7.4803
8.2677
24
24
28
0.9449
0.9449
1.1024
65 000
66 300
88 400
14 600
14 900
19 900
67 000
72 000
93 000
15 100
16 200
20 900
7 500
7 000
6 300
4 500
5 600
5 300
1.85
1.70
3.05
4.10
3.70
6.70
61932 MA
61936 MA
61938 MA
160
180
190
6.2992
7.0866
7.4803
220
250
260
8.6614
9.8425
10.2362
28
33
33
1.1024
1.2992
1.2992
92 300
119 000
117 000
20 700
26 800
26 300
98 000
134 000
134 000
22 000
30 100
30 100
6 000
5 300
5 000
5 000
4 300
4 300
3.25
5.05
5.25
7.20
11.10
11.60
61940 MA
61944 MA
61948 MA
200
220
240
7.8740
8.6614
9.4488
280
300
320
11.0236
11.8110
12.5984
38
38
38
1.4961
1.4961
1.4961
148 000
151 000
159 000
33 300
33 900
35 700
166 000
180 000
200 000
37 300
40 500
45 000
4 800
4 300
4 000
3 800
3 600
3 200
7.40
8.00
8.60
16.30
17.60
19.00
44
lb
Single row
Conrad
Open
Standard
Series: 61952 MA 619/900
Size: 260 mm 900 mm
10.2362 in 35.4331 in
OPEN
Open
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
Speed rating
Static
C0
lbf
Mass
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
61952 MA
61956 MA
61960 MA
260
280
300
10.2362
11.0236
11.8110
360
380
420
14.1732
14.9606
16.5354
46
46
56
1.8110
1.8110
2.2047
212 000
216 000
270 000
47 700
48 600
60 700
270 000
285 000
375 000
60 700
64 100
84 300
3 600
3 200
3 000
3 000
2 800
2 400
14.50
15.00
24.50
32.00
33.10
54.00
61964 MA
61968 MA
61972 MA
320
340
360
12.5984
13.3858
14.1732
440
460
480
17.3228
18.1102
18.8976
56
56
56
2.2047
2.2047
2.2047
276 000
281 000
291 000
62 000
63 200
65 400
400 000
425 000
450 000
89 900
95 500
101 200
2 800
2 600
2 600
2 400
2 200
2 200
25.50
26.50
28.00
56.20
58.40
61.70
61976 MA
61980 MA
61984 MA
380
400
420
14.9606
15.7480
16.5354
520
540
560
20.4724
21.2598
22.0472
65
65
65
2.5591
2.5591
2.5591
338 000
345 000
351 000
76 000
77 600
78 900
540 000
570 000
600 000
121 400
128 100
134 900
2 400
2 200
2 200
1 900
1 800
1 800
40.00
41.50
43.00
88.20
91.50
95.00
61988 MA
61992 MA
61996 MA
440
460
480
17.3228
18.1102
18.8976
600
620
650
23.6220
24.4094
25.5906
74
74
78
2.9134
2.9134
3.0709
410 000
423 000
449 000
92 200
95 100
100 900
720 000
750 000
815 000
161 900
168 600
183 200
2 000
1 900
1 800
1 600
1 600
1 500
60.50
62.50
74.00
133.40
137.80
163.10
619/500 MA
619/530 MA
619/560 MA
500
530
560
19.6850
20.8661
22.0472
670
710
750
26.3780
27.9528
29.5276
78
82
85
3.0709
3.2283
3.3465
462 000
488 000
494 000
103 900
109 700
111 100
865 000
930 000
980 000
194 500
209 100
220 300
1 700
1 600
1 500
1 400
1 300
1 200
77.00
90.50
105.00
169.80
199.50
231.50
619/600 MA
619/630 N1MA
619/670 MA
600
630
670
23.6220
24.8031
26.3780
800
850
900
31.4961
33.4646
35.4331
90
100
103
3.5433
3.9370
4.0551
585 000
624 000
676 000
131 500
140 300
152 000
1 220 000
1 340 000
1 500 000
274 300
301 200
337 200
1 400
1 300
1 200
1 100
1 100
1 000
125.00
160.00
185.00
275.60
352.70
407.90
619/710 MA
619/750 MA
619/900
710
750
900
27.9528
950
29.5276 1 000
35.4331 1 090
37.4016
39.3701
42.9133
106
112
85
4.1732
4.4094
3.3464
663 000
761 000
852 000
149 000
171 100
191 500
1 500 000
1 800 000
2 280 000
337 200
404 600
512 500
1 100
1 000
800
900
850
670
220.00
255.00
350.00
485.00
562.20
771.60
45

Single row
ABEC 5
Open
Standard
Series: 6205/C78 6218/C78
Size: 25 mm 90 mm
0.9843 in 3.5433 in
Series: 6303/C78 6317/C78
Size: 17 mm 85 mm
0.6693 in 3.3465 in
Y/C78
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
mm
in
6205/C78
6206/C78
6207/C78
25
30
35
0.9843
1.1811
1.3780
52
62
72
2.0472
2.4409
2.8346
15
16
17
6208/C78
6209/C78
6210/C78
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1496
3.3465
3.5433
6211/C78
6212/C78
6213/C78
55
60
65
2.1654
2.3622
2.5591
100
110
120
6214/C78
6215/C78
6216/C78
70
75
80
2.7559
2.9528
3.1496
6217/C78
6218/C78
85
90
6303/C78
6304/C78
6305/C78
Dynamic
C
TC/C78
Speed rating
Static
C0
Reference
speed
r/min
Limiting
speed
r/min
lbf
lbf
0.5906
0.6299
0.6693
14 800
20 300
27 000
3 330
4 560
6 070
7 800
11 200
15 300
1 750
2 520
3 440
28 000
24 000
20 000
18
19
20
0.7087
0.7480
0.7874
32 500
35 100
37 100
7 310
7 890
8 340
19 000
21 600
23 200
4 270
4 860
5 220
3.9370
4.3307
4.7244
21
22
23
0.8268
0.8661
0.9055
46 200
55 300
58 500
10 390
12 430
13 150
29 000
36 000
40 500
125
130
140
4.9213
5.1181
5.5118
24
25
26
0.9449
0.9843
1.0236
63 700
68 900
72 800
14 320
15 490
16 370
3.3465
3.5433
150
160
5.9055
6.2992
28
30
1.1024
1.1811
87 100
101 000
17
20
25
0.6693
0.7874
0.9843
47
52
62
1.8504
2.0472
2.4409
14
15
17
0.5512
0.5906
0.6693
6306/C78
6307/C78
6308/C78
30
35
40
1.1811
1.3780
1.5748
72
80
90
2.8346
3.1496
3.5433
19
21
23
6309/C78
6310/C78
6311/C78
45
50
55
1.7717
1.9685
2.1654
100
110
120
3.9370
4.3307
4.7244
6312/C78
6313/C78
6314/C78
60
65
70
2.3622
2.5591
2.7559
130
140
150
6315/C78
6316/C78
6317/C78
75
80
85
2.9528
3.1496
3.3465
160
170
180
kg
lb
18 000
15 000
13 000
0.13
0.20
0.28
0.29
0.44
0.62
18 000
17 000
15 000
11 000
11 000
10 000
0.36
0.41
0.46
0.79
0.90
1.01
6 520
8 090
9 100
14 000
13 000
12 000
9 000
8 000
7 500
0.60
0.78
0.99
1.32
1.72
2.18
45 000
49 000
55 000
10 120
11 020
12 360
11 000
10 000
9 500
7 000
6 700
6 000
1.07
1.20
1.42
2.40
2.60
3.10
19 580
22 700
64 000
73 500
14 390
16 520
9 000
8 500
5 600
5 300
1.80
2.15
4.00
4.70
14 300
16 800
23 400
3 210
3 780
5 260
6 550
7 800
11 600
1 470
1 750
2 610
34 000
30 000
24 000
22 000
19 000
16 000
0.12
0.14
0.23
0.26
0.31
0.50
0.7480
0.8268
0.9055
29 600
35 100
42 300
6 650
7 890
9 510
16 000
19 000
24 000
3 600
4 270
5 400
20 000
19 000
17 000
13 000
12 000
11 000
0.34
0.46
0.63
0.70
1.00
1.40
25
27
29
0.9843
1.0630
1.1417
55 300
65 000
74 100
12 430
14 610
16 660
31 500
38 000
45 000
7 080
8 540
10 120
15 000
13 000
12 000
9 500
8 500
8 000
0.84
1.10
1.39
1.90
2.40
3.10
5.1181
5.5118
5.9055
31
33
35
1.2205
1.2992
1.3780
85 200
97 500
111 000
19 150
21 920
24 950
52 000
60 000
68 000
11 690
13 490
15 290
11 000
10 000
9 500
7 000
6 700
6 300
1.75
2.10
2.55
3.90
4.60
5.60
6.2992
6.6929
7.0866
37
39
41
1.4567
1.5354
1.6142
119 000
130 000
140 000
26 750
29 220
31 470
76 500
86 500
96 500
17 200
19 450
21 690
9 000
8 500
8 000
5 600
5 300
5 000
3.05
3.59
4.30
6.70
7.90
9.50
46
Mass
Single row
Max type
Open, shielded, snap ring
Standard
Series: 206 220
Size: 30 mm 100 mm
1.1811 in 3.9370 in
NR
2Z
Series: 308 318

Size: 40 mm 90 mm
1.5748 in 3.5433 in
2ZNR
Open
Designation
Bore
d
Speed rating1
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
lbf
lbf
Reference
speed
r/min
0.6299
0.6693
0.7087
21 000
27 760
33 370
4 800
6 300
7 600
14 510
19 740
24 200
3 300
4 500
5 500
20 000
17 000
15 000
12 000
11 000
9 500
0.21
0.31
0.39
0.46
0.68
0.86
19
20
21
0.7480
0.7874
0.8268
35 100
38 920
48 110
7 900
8 800
10 900
26 070
29 760
37 670
5 900
6 700
8 500
14 000
13 000
12 000
9 000
8 000
7 500
0.44
0.50
0.66
0.97
1.10
1.50
4.3307
4.7244
4.9213
22
23
24
0.8661
0.9055
0.9449
55 540
60 500
66 000
12 500
13 700
14 900
43 400
58 500
65 500
9 800
13 200
14 800
11 000
10 000
9 500
6 700
6 000
6 000
0.85
1.05
1.15
1.90
2.30
2.50
130
140
150
5.1181
5.5118
5.9055
25
26
28
0.9843
1.0236
1.1024
72 100
88 000
96 800
16 300
19 800
21 800
72 000
85 000
100 000
16 200
19 200
22 500
9 000
8 500
7 500
5 600
5 300
4 800
1.25
1.55
1.95
2.80
3.40
4.30
3.5433
3.7402
3.9370
160
170
180
6.2992
6.6929
7.0866
30
32
34
1.1811
1.2598
1.3386
112 000
121 000
134 000
25 200
27 300
30 200
114 000
122 000
140 000
25 700
27 500
31 500
7 000
6 700
6 300
4 500
4 300
4 000
2.35
2.70
3.45
5.20
6.00
7.60
25
30
35
0.9843
1.1811
1.3780
62
72
80
2.4409
2.8346
3.1496
17
19
21
0.6693
0.7480
0.8268
22 900
29 490
34 860
5 200
6 700
7 900
15 600
20 480
24 640
3 600
4 700
5 600
20 000
18 000
16 000
13 000
11 000
10 000
0.24
0.37
0.48
0.50
0.80
1.10
308
309
310
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
23
25
27
0.9055
0.9843
1.0630
45 200
55 260
64 730
10 200
12 500
14 600
33 570
41 260
49 100
7 600
9 300
11 100
14 000
13 000
11 000
9 000
8 000
7 000
0.64
0.88
1.15
1.40
1.90
2.50
311
312
313
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
29
31
33
1.1417
1.2205
1.2992
79 200
91 300
102 000
17 800
20 500
22 900
67 000
78 000
90 000
15 100
17 600
20 300
10 000
9 500
9 000
6 700
6 000
5 600
1.5
1.85
2.3
3.30
4.10
5.10
314
315
316
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
35
37
39
1.3780
1.4567
1.5354
114 000
125 000
138 000
25 600
28 100
31 000
102 000
116 000
129 000
23 000
26 100
29 000
8 000
7 500
7 000
5 000
4 800
4 500
2.75
3.25
3.95
6.10
7.20
8.70
317
318
85
90
3.3465
3.5433
180
190
7.0866
7.4803
41
43
1.6142
1.6929
147 000
157 000
33 100
35 300
146 000
160 000
32 900
36 000
6 700
6 300
4 300
4 000
4.6
5.4
10.10
11.90
mm
in
206
207
208
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409
2.8346
3.1496
16
17
18
209
210
211
45
50
55
1.7717
1.9685
2.1654
85
90
100
3.3465
3.5433
3.9370
212
213
214
60
65
70
2.3622
2.5591
2.7559
110
120
125
215
216
217
75
80
85
2.9528
3.1496
3.3465
218
219
220
90
95
100
305
306
307
Dynamic
C
Static
C0
Mass
Limiting
speed
r/min
kg
lb
47
Notes
48
Angular contact
ball bearings
Nomenclature
7200 BE CB Y HC5
4
2
1
1. Design:
2. Clearance:
3. Cage designs:
40 contact angle
(C0)*
Normal clearance (3000 series)
Pressed brass cage,

ball guided
BE
40 contact angle,
high capacity,
all ISO corners
C2
Axial clearance tighter than

normal (3000 and QJ series)

Axial clearance looser than

normal (3000 and QJ series)
MA
Machined window-type brass

cage, outer ring centered
Injection molded cage

of fiberglass reinforced
polyamide 6.6, rolling
element guided
PHAS
Injection molded window-type

cage of fiberglass reinforced
polyetheretherketone (PEEK),
with lubrication grooves in the
guiding surfaces, outer ring center
Pressed steel cage,

Machined steel cage,

C3
A
Conrad assembly (3000 series)
Max type (3000 series)
Split inner ring (3300 series)
7000 series clearance
NR
Snap ring (3000 series)
CA
Modified for duplex mounting

with axial clearance < normal
N2
Locating slot (QJ series)
CB
2Z
Shield on both sides

(3000 series)

with normal axial clearance
CC
2RS1
Seals of synthetic rubber (NBR)

on both sides (3000 series)

with axial clearance > normal
GA

with light preload
GB

with medium preload
GC

with heavy preload
G..
Special preload, value in daN
Note: 3000 series are double row

angular contact bearings
4. Special features:
HC4
Full ceramic bearing
HC5
Ceramic ball set
* Not marked on bearing or package.
49
Angular contact ball bearings
Product
Details
Technical
features
Single row ACBB
Double row ACBB
Four-point contact ACBB
Boundary
dimensions
In accordance with
ISO 15-1998
In accordance with
ISO 15-1998
In accordance with
ISO 15-1998
Tolerances
ABEC 3 (P6)
ABEC 3
ABEC 1
Heat stabilization
257 F
(125 C)
257 F
(125 C)
257 F
(125 C)
Misalignment
None contact SKF
None contact SKF
None contact SKF
Cage materials
Polyamide (P)
Machined brass (M)
Pressed steel (J)
Polyamide (TN9)
(limited sizes only)
Pressed steel (H)
Machined brass (M, MA)
Axial load max
1.4 x C0 for
single or tandem
mounted bearings
0.7 x C0 Conrad
Fa / Fr 0.3
0.7 x C0
0.7 x C0 for duplex

mounted bearings
Seals
Not available
2RS1 Synthetic rubber (NBR)
Not available
Shields
Consult SKF for

NILOS ring options
2Z Stamped steel
Consult SKF for

NILOS ring options
Single row
angular contact
ball bearing
50
Four-point
angular contact
ball bearing
Double row
angular contact
ball bearing
Thrust pack
angular contact
ball bearing
Introduction
Introduction
Angular contact ball bearings,

single row
SKF standard angular contact ball bearings are

available with axial clearances, preloads and
high precision. Single row angular contact ball
bearings are designed to accommodate axial
loads acting in one direction. Under radial
loads, an induced force acting in the axial
direction is produced which must be counteracted. Consequently, the single bearings are
normally adjusted against a second bearing.
SKF angular contact ball bearings are produced in a wide variety of designs and sizes.
Those commonly used in general engineering
are shown in this catalog:
Single row angular contact ball bearings can

accommodate combined loads however the
axial loads can only act in one direction
(Figure 1). Under radial loads, a force acting
in the axial direction is produced which must
be counteracted. Consequently, the bearings
are normally adjusted against a second
bearing.
The single row angular contact ball bearings
shown in the tables have one high and one
low shoulder on each ring, enabling a large
number of balls to be incorporated. This gives
the bearings relatively high load carrying
capacity. The contact angle is 40 (suffix B)
and the bearings are therefore suitable for
heavy axial loads. They are of non-separable
design and permit relatively high-speed
operation.
Bearings of the BE design feature an
increased load carrying capacity, and either
machined brass (M) or glass fiber reinforced
polyamide 6-6 (P) cages as standard.
The single row angular contact ball bearings
are produced in two standard versions for
different design purposes. The standard design
(no additional designation suffix such as BEP)
is intended for arrangements where only one
bearing is used at each bearing position
(Figure 4, page 58).
The most common version, identified by
suffix CB (universal matching) is designed for
arrangements where two or more bearings
are mounted immediately adjacent to each
other in random order (back-to-back,
face-to-face or tandem). Because of demand,
the larger sized bearings are only produced
with universal matching (suffix CB) (Figure 5,
page 58).
Single row bearings

Double row bearings
Four-point contact ball bearings
Thrust pack
Basic design
Angular contact ball bearings have raceways in
the inner and outer rings that are displaced
with respect to each other in the direction of
the bearing axis. This means that they are
particularly suitable for the accommodation of
combined loads; for example, simultaneously
acting radial and axial loads.
The axial load carrying capacity of angular
contact ball bearings increases with increasing
contact angle . This is defined as the angle
between the line joining the points of contact
between the ball and the raceways in the radial plane, along which the load is transmitted
from one raceway to the other, and a line
perpendicular to the bearing axis. For single
row bearings, the magnitude of the contact
angle is indicated by a suffix in the designation
(B = 40 degrees) (Figure 1). For double row
angular contact ball bearings, the contact
angle is 30 degrees and for QJ four-point
angular contact ball bearings the contact angle
is 35 degrees and neither is indicated in the
nomenclature.
Figure 1
SKF Explorer class

bearings
High performance SKF Explorer angular contact ball bearings are printed in blue in the
product tables. SKF Explorer bearings retain
the designation of the earlier standard bearings, e.g. 7208 BECBP. However, each bearing
and its box are marked with the name SKF
page 23.
Product highlights
High running accuracy and speed
capabilities
Angular contact ball bearings feature
high radial and axial load capacity
combined with high speed capabilities.
SKF ACBB are made as standard to
ISO P6 or ABMA ABEC 3 precision as
standard.
Universal matching
Angular contact ball bearings are
manufactured for universal mounting
in multiple arrangements, including
face-to-face, back-to-back and
tandem.

Available in a wide range (10 to 240
mm inside bore diameter) with cage
and clearance / preload combinations.
The double row design is available with
a choice of shields, seals and snap
rings as well as max-type bearings
with a filling slot. Special application
designs include 4-point contact and
thrust pack.
Machined brass cage for heavy

duty applications
The machined brass cage provides
better performance and longer service
life under harsh conditions and can be
used in applications where a standard
metal or plastic cage is normally used.
Meets ANSI pump

requirements
Angular contact ball bearings are widely used in centrifugal pump applications
and are manufactured in accordance
with ANSI pump standards.
51

Introduction

double row (Figure 1a)

four-point (Figure 1b)
Variations
SKF double row ball bearings are designed

with solid or one-piece inner and outer rings
with contact angles converging outside the
bearing providing overall system rigidity.
The double row angular contact ball bearings are available in two styles, Conrad (suffix
A) and Max type (suffix E). The more popular
style is the Conrad type. This assembly uses a
slight elastic deflection of the outer ring to
insert the last ball. This results in uninterrupted raceways with smooth running, and
significant thrust carrying capacity in both
directions.
Bearings of the Max type design (suffix E)
have a filling slot for inserting the balls. This
permits assembly with a greater number of
balls than in the previously described Conrad
type bearings.
Filling slot bearing features are similar to
those of the Conrad type; however, because of
the greater number of balls (with the exception of a few sizes) their radial load carrying
capacity is often higher than that of the
Conrad type. On the other hand, heavy thrust
loads can be accommodated in only one direction. These bearings should be mounted so
that the predominant axial load acting on the
shaft is directed away from the filling slot
(Figure 1a). Thrust loads in the direction of
the filling slot should not exceed a thrust to
radial load ratio of Fa / Fr = 0.3.
Part number markings are normally located
on either the side face or the O.D. The side
face marking is always on the side opposite
the filling slot, and the O.D. marking is offset
from the center away from the side with the
filling slot. Therefore, even double sealed or
shielded bearings with the filling slot covered
from view can be oriented correctly.
Four-point contact ball bearings are single row

angular contact ball bearings having raceways
which are designed to enable axial loads to be
accommodated in both directions. They need
less axial space than double row bearings. The
four-point contact ball bearings shown in the
following tables have a contact angle of 35
and a two-part inner ring, allowing a large
number of balls to be incorporated, thus
providing a high load carrying capacity. The
bearings are separable, i.e. the inner ring
halves and the outer ring with ball and cage
assembly can be mounted individually.
Angular contact ball bearings, single

row for universal matching

thrust pack
A thrust pack bearing consists of a standard
QJ bearing and a single row angular contact
bearing (BEGAM version) matched together
and are intended for applications having
predominate axial load in one direction. The
axial load should not reverse direction during
operation except for transient conditions such
as at machine start up or shut-down, else the
BEGAM bearing may become unloaded and
have possible skidding problems. These bearings are matched in sets and are serialized and
therefore are not interchangeable amongst sets.
These bearings are specially manufactured so

that when mounted in random order (back-toback, face-to-face or tandem) (Figure 2), but
immediately adjacent to each other, the predetermined value of axial internal clearance or
preload will be attained. An even distribution of
load will occur without shims or similar devices.
The standard bearings for universal matching
carry the suffix CB where C indicates clearance
and B the magnitude of the clearance (Figure 3).
Bearings with a smaller or greater clearance
are also available (suffixes CA and CC, respectively) as are bearings with light, moderate or
heavy preload, (suffixes GA, GB and GC,
respectively where G = preload or negative
clearance). When ordering bearings for universal matching; for example 7206 BECB, it is
necessary to indicate the number of individual
bearings required since SKF does not stock
these in sets.
Figure 1a
Figure 1b
Primary thrust direction
Double row, angular contact

ball bearing
Four-point contact
ball bearing
Figure 2
Tandem
arrangement
52
Back-to-back
arrangement
Face-to-face
arrangement
Introduction
Limiting speeds
The limiting speeds listed in the bearing tables
are guideline values and are valid for single row
bearings. The values under oil lubrication are
maximum values and the values under grease
lubrication are maximum values that can be
attained using a good quality grease of a soft
consistency.
If single bearings are to be adjusted against
each other in matched sets of two, three or
four bearings, the limiting speed values given in
the bearing tables must be reduced. Reduction
factors are given in the table below.
Load carrying capacity of bearing sets

The values given in the bearing tables for the
basic dynamic load ratings apply to single bearings. The basic dynamic and static load ratings
for sets of bearings arranged back-to-back,
face-to-face or in tandem is obtained by multiplying the C value for a single bearings by:
Two bearings
Three bearings
Four bearings
Reduction factors
Two bearings
0.80
Three bearings
0.70
Four bearings
0.65
Precision angular contact ball bearings

for machine tools
Large-size single and double row bearings
for heavy engineering applications
Hub units produced for the automotive
industry
1.62 x C
2.16 x C
2.64 x C
Where the basic static load rating is

concerned, the table value C0 should be
multiplied by the number of bearings in the
set, 2, 3 or 4.
For example, a pair of 7205 BEGAP angular
contact ball bearings will have the following
values:
Reduction factors for limiting speeds

angular contact ball bearings, single row
Bearing arrangement
Special solutions using

angular contact ball
bearings
The precision angular contact ball bearings

are available with a contact angle of 15
(suffix CD) or 25 (suffix ACD) and can be
supplied either individually or in matched
sets of two, three or four bearings.
C (single) = 3510 lbs

C (pair) = 3510 x 1.62 = 5690 lbs

C0 (single) = 2290 lbs

C0 (pair) = 2290 x 2 = 4580 lbs
Grease speed (single) = 10000 rpm
Grease speed (pair) = 10000 x 0.8 = 8000 rpm
The C, C0 and speed limits of the pair of
bearings must be used for calculation purposes
in this case.
Figure 3
0
+
Clearance
CC
CB
Axial
Axial
preload
preload
CA
GA
Axial
Axial
clearance
clearance
GB
GC
Preload
53

Introduction
Figure 3a
Conrad type
Designations for Conrad type double-row ball bearings with various combinations of seals, shields and snap rings
A-Z
A-2Z
A-RS
A-2RS
ANR
A-ZNR
A-ZNBR
A-2ZNR
A-RSNR
A-RSNBR
A-2RSNR
Max type
Designations for Max type (single slot) filling slot double-row ball bearings with various combinations of seals, shields and snap rings
ENR
54
E-Z
E-ZB
E-2Z
E-RS
E-RSB
E-2RS
E-ZNR
E-ZNBR
E-2ZNR
ENAR
E-RSNR
E-RSNBR
E-2RSNR
E-ZNAR
E-ZNABR
E-2ZNAR
E-RSNAR
E-RSNABR
E-2RSNAR
Introduction

double row
Shielded (Z) and sealed (RS) bearings
In addition to the open designs, most SKF
double row ball bearings are offered with
shields or seals, on either one or both sides. In
most sizes, open bearings also contain seal
grooves on the inner and/or outer rings.
Shields (suffix Z and 2Z) are non-contacting.
They form a small gap with a chamfer on the
inner ring. They are made from pressed steel
and are fixed into an outer ring groove. This
non-contacting closure is designed to retain
lubricant and exclude larger particles of foreign
matter. These shielded bearings are primarily
intended for applications with inner ring rotation. Single shielded bearings can be used with
oil or grease lubrication, while double shielded
bearings are packed with a predetermined
quantity of grease, providing maintenance-free
operation for the life of the bearings.
Most bearings are also available with either
one or two contacting seals, (suffix -RS and
-2RS). The seals consist of an oil and wear
resistant elastomer bonded to a metal plate.
The O.D. of either of the seal is firmly fixed into
an outer ring groove. The lip at the I.D. of the
seal contacts an inner ring seal chamfer for
effective closure. This seal effectively excludes
solid contaminants and moisture from the
inside surfaces of the bearing. The permissible
operating temperature range for the seals with
a proper lubricant is -40 to +250 F (-40 to
+120 C). Single sealed bearings can be
Max type bearings use a suffix A to indicate

that the snap ring is on the side of the filling
slot (NAR). Suffix B in single seal or shield designation indicates that the seal or shield is on
the opposite side of the filling slot (RSB or ZB).
regreased while double sealed bearings are

greased for life.
They should not be heated at temperatures greater than 250 F (120 C) prior
to mounting and must on no account
be washed.
Snap rings
Snap rings (suffix NR) in the outer ring can
provide an easy method of locating the bearing
in the application. The snap rings and the snap
ring grooves in the outer rings generally conform to ABMA Standard 20 and ISO standard
464. Important snap ring dimensions are
shown in the deep groove ball bearings section,
Table 4 page 57.
Combination of seals, shields and snap rings
Most bearings are available in various combinations of seals, shields and snap rings. (Figure
3a) illustrates the designations for Conrad type
bearings in various configurations and shows
the same for max-type filling slot bearings.
In a single sealed or shielded Conrad type
bearing with snap ring, the snap ring is normally on the opposite side of the seal or shield.
An additional suffix B indicates the snap ring is
on the same side as the seal or shield, e.g. NBR.

four-point
Locating slots
Four-point contact ball bearings are designed
to accommodate predominantly axial loads and
are arranged as thrust bearings with radial
clearance in the housing in many applications.
To permit simple location and prevent rotation
of the outer ring, all bearings with an outside
diameter of 160 mm and above are provided
with two locating slots in the outer ring (N2
design). The dimensions of these locating slots
are given in Table 1.
Table 1
Locating slots in outer ring of four-point contact ball bearings
A
D
h
A
b
r0
45
A-A
Outside
diameter
D
over
Dimensions
Series QJ 2
incl.
mm
in
Series QJ 3
h
r0
r0
mm
in
mm
in
mm in
mm
in
mm
in
mm in
170
6.6929
6.5
0.256
8.1
0.319
0.039
8.5
0.335
10.1
0.398
0.079
170
6.6929
210
8.2677
8.5
0.335
10.1
0.398
0.787
10.5
0.413
11.7
0.461
0.079
210
8.2677
270
10.6299
10.5
0.413
11.7
0.461
0.787
10.5
0.413
11.7
0.461
0.079
270
10.6299
400
15.784
10.5
0.413
12.7
0.500
0.787
10.5
0.413
12.7
0.500
0.079
55

Introduction
Internal clearance
Table 2
Axial internal clearance

single row angular contact ball bearings
Internal clearance in a single row angular contact ball bearing is only obtained after mounting
and is dependent on adjustment against a second bearing that provides axial location in the
opposite direction.
Bearings for universal pairing (suffix CB) are
the standard SKF bearings for paired mounting
in random order (back-to-back, face-to-face or
tandem). Bearings can be supplied with smaller
axial internal clearance (suffix CA) or larger (suffix CC) or with preload (suffixes GA, GB and GC)
for universal pairing.
Bearings identified by suffix CA, CB or CC can
be mounted immediately adjacent to each other
in any order and two or more bearings may be
used. Bearings with preload of the GA, GB and
GC designs can only be arranged in pairs, otherwise the preload will increase.
The values of axial internal clearance for the
classes CA, CB and CC can be found in Table 2.
They are valid for bearings arranged back-toback or face-to-face before mounting and under
zero measuring load. Preload values for classes
GA, GB and GC are given in Table 2a. Table 3
shows a conversion from the old preload
suffices to the current suffix.
Unmounted axial internal clearance of single row angular contact ball

bearings of series 72B (E), 73B (E) and 74B (B) when arranged in random
pairs (back-to-back or face-to-face)
Bore
diameter

CA
CB
d
over incl.
mm
min max min

m
in
10
18
10
18
30
4
5
7
12
13
15
30
50
80
50
80
120
9
11
14
120 180
180 250
250 315
17
21
26
max
CC
min max
m
min
in
0.0002 0.0005
0.0002 0.0005
0.0003 0.0006
14
15
18
22
23
26
17
23
26
0.0004 0.0007
0.0004 0.0009
0.0006 0.0010
22
26
32
29
37
42
0.0007 0.0011
0.0008 0.0015
0.0010 0.0017
35
45
52
max
min max min

m
in
max
0.0006 0.0009
0.0006 0.0009
0.0007 0.0010
22
24
32
30
32
40
0.0009
0.0009
0.0013
0.0012
0.0013
0.0016
30
38
44
0.0009 0.0012
0.0010 0.0015
0.0013 0.0017
40
48
55
48
60
67
0.0016
0.0019
0.0022
0.0019
0.0024
0.0026
47
61
68
0.0014 0.0019
0.0018 0.0024
0.0020 0.0027
62
74
90
74 0.0024
90 0.0029
106 0.0035
0.0029
0.0035
0.0042
Radial clearance [~=] 0.85 axial clearance.
Table 2a
Unmounted preload of single row angular contact ball bearings of series 72B (E),
73B (E) and 74 (B) when arranged in random pairs (back-to-back or face-to-face)
Bore
diameter
Preload
GA
GB
GC
d
over
mm
incl.
min max min

m
in
max
max
N
max
lbf
min max min

m
in
max
min
N
max
min max
lbf
min max min

m
in
max
10
18
30
18
30
50
4
4
4
-4
-4
-4
0.0002
0.0002
0.0002
-0.0002
-0.0002
-0.0002
80
120
160
18
27
36
-2
-2
-2
-10
-10
-10
-0.0001
-0.0001
-0.0001
-0.0004
-0.0004
-0.0004
30
40
60
330
480
630
7
9
13
74
108
142
-8
-8
-8
-0.0006 230
-0.0006 340
-0.0006 450
50
80
120
80
120
180
6
6
6
-6
-6
-6
0.0002
0.0002
0.0002
-0.0002
-0.0002
-0.0002
380
410
540
86
92
122
-3
-3
-3
-15
-15
-15
-0.0001
-0.0001
-0.0001
-0.0006
-0.0006
-0.0006
140 1 500 31
150 1 600 34
200 2 150 45
338
360
484
-12 -24 -0.0005

-12 -24 -0.0005
-12 -24 -0.0005
-0.0009 1 080 3 050 243 686

-0.0009 1 150 3 250 259 731
-0.0009 1 500 4 300 337 968
180
250
250
315
8
8
-8
-8
0.0003
0.0003
-0.0003
-0.0003
940 212
1 080 243
-4
-4
-20
-20
-0.0002
-0.0002
-0.0008
-0.0008
330 3 700 74
380 4 250 85
833
956
-16 -32 -0.0006

-16 -32 -0.0006
-0.0013 2 650 7 500 596 1 688

-0.0013 3 000 8 600 674 1 935
56
-16 -0.0003
-16 -0.0003
-16 -0.0003
min
N
max
min max
lbf
660
52 149
970
76 218
1 280 101 288
Introduction
Axial internal clearance double row

angular contact ball bearings
Table 3
Old/new preload designation interchange,
single row angular contact ball bearings 72xx, 73xx and 74xx series
Internal clearances for double row angular

contact ball bearings differ from deep groove
ball bearings in that axial rather than radial
clearance is specified. Table 4 shows the axial
clearance of the SKF double row angular contact
bearings in four standard clearance ranges; C2
(less than normal clearance), normal clearance,
C3 (greater than normal clearance), and C4
(greater than C3 clearance). These are valid
for bearings before mounting under zero
measuring load.
Bore
size
00
01
02
03
04
06
07
08*
09
10
11
12
13
14
15
16
17
18
19
20
21
22
24
26
28
30
32
34
36

four-point contact ball bearings
Standard manufacture SKF four-point contact
ball bearings have Normal axial internal clearance. Most sizes can also be supplied with
greater or smaller internal clearance than
Normal. Availability should be checked before
ordering.
The values for the axial internal clearance are
shown in Table 5 and are for bearings before
mounting under zero measuring load.
Old versus new designations

on SRACBB (Table 3)
Use this table to determine which new preload
designations replace old preload designations.
Simply find the bearing bore size/diameter on
the left, and the old preload across the top. The
new designation is at the point where the bore
size/diameter row intersects with the old preload
column.
*Example: 7308 BEAG1Y = 08 bore size,
40 mm bore diameter
G1 (100 lbs) preload
Replace with: 7308 BEGBY
Bore
diameter
Old preload suffix
(mm)
G02
G05
G1*
G2
G3
G5
10
12
15
17
20
30
35
40*
45
50
55
60
65
70
75
80
85
90
95
100
105
110
120
130
140
150
160
170
180
GB
GB
GB
GB
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GA
GC
GC
GC
GC
GC
GC
GB
GB*
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GC
GC
GC
GC
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
GC
Table 4
Axial internal clearance of Conrad type and filling slot double row angular contact ball bearings
32 and 33 series (values in 0.001 mm)
Bore
diameter

C2
Normal
d
over
mm
incl.
min max
m
min
in
10
18
10
18
24
1
1
2
11
12
14
24
30
40
30
40
50
2
2
2
50
65
80
65
80
100
100
110
max
C3
C4
min
m
max
min
in
max
min
m
max
min
in
max
min
m
max
min
in
max
0.0000 0.0004
0.0000 0.0005
0.0001 0.0006
5
6
7
21
23
25
0.0002
0.0002
0.0003
0.0008
0.0009
0.0010
12
13
16
28
31
34
0.0005
0.0005
0.0006
0.0011
0.0012
0.0013
40
42
43
60
64
69
0.0016 0.0024
0.0017 0.0025
0.0017 0.0027
15
16
18
0.0001 0.0006
0.0001 0.0006
0.0001 0.0007
8
9
11
27
29
33
0.0003
0.0004
0.0004
0.0011
0.0011
0.0013
18
21
23
37
40
44
0.0007
0.0008
0.0009
0.0015
0.0016
0.0017
45
48
51
75
84
90
0.0018 0.0030
0.0019 0.0033
0.0020 0.0035
3
3
3
22
24
26
0.0001 0.0009
0.0001 0.0009
0.0001 0.0010
13
15
18
36
40
46
0.0005
0.0006
0.0007
0.0014
0.0016
0.0018
26
30
35
48
54
63
0.0010
0.0012
0.0014
0.0019
0.0021
0.0025
55
61
70
96
106
123
0.0022 0.0038
0.0024 0.0042
0.0028 0.0048
30
0.0002 0.0012
22
53
0.0009
0.0021
42
73
0.0017
0.0029
80
148
0.0031 0.0058
57

Introduction
Table 5
Axial internal clearance of four-point contact ball bearings
Bore
diameter
d
over
mm
in
incl.
mm
in
C2
min
m
max min
in
max
Normal
min
max
m
min
in
C3
max
min
m
max min
in
C4
max
min
m
max
min
in
max
10
18
0.3937
0.7087
15
55
0.0006
0.0022
45
85
0.0018
0.0033
75
125
0.0030
0.0049
115
165 0.0045 0.0065
18
40
0.7087
1.5748
26
66
0.0010
0.0026
56
106
0.0022
0.0042
96
146
0.0038
0.0057
136
186 0.0054 0.0073
40
60
1.5748
2.3622
36
86
0.0014
0.0034
76
126
0.0030
0.0050
116
166
0.0046
0.0065
156
206 0.0061 0.0081
60
80
2.3622
3.1496
46
96
0.0018
0.0038
86
136
0.0034
0.0054
126
176
0.0050
0.0069
166
226 0.0065 0.0089
80
100
3.1496
3.9370
56
106
0.0022
0.0042
96
156
0.0038
0.0061
136
196
0.0054
0.0077
186
246 0.0073 0.0097
100
140
3.9370
5.5118
66
126
0.0026
0.005
116
176
0.0046
0.0069
156
216
0.0061
0.0085
206
266 0.0081 0.0105
140
180
5.5118
7.0866
76
156
0.0030
0.0061
136
196
0.0054
0.0077
176
246
0.0069
0.0097
226
296 0.0089 0.0116
180
220
7.0866
8.6614
96
176
0.0038
0.0069
156
226
0.0061
0.0089
206
276
0.0081
0.0109
256
326 0.0101 0.0128
Radial clearance [~=] 0.7 axial clearance.
Design of bearing arrangements

When designing bearing arrangements using
single row angular contact ball bearings it is
necessary to pay attention to the special
characteristics of the bearings. Because of
their internal design they cannot be used singly
and must be used either with a second bearing
(Figure 4) or as bearing sets (Figure 5).
As already mentioned under "Internal clearance", it is necessary to adjust the two single
row angular contact ball bearings of an
arrangement against each other until the
operational clearance or requisite preload is
obtained.
Arrangements using bearings for universal
mounting, where the bearings are immediately
adjacent to each other, do not require adjustment. Here, the required operational preload or
clearance is obtained by choosing an appropriate
preload or clearance class as well as suitable
fits for the bearings in the housing and on the
shaft. For more specific mounting instructions
visit the SKF website at www.skf.com/mount or
contact SKF Applications Engineering.
58
Figure 4
Figure 5
Introduction
Loads

four-point contact bearings
Minimum load

single row bearings of the B and BE
designs when mounted as single
bearings or paired in tandem
When four-point contact ball bearings with a

contact angle of 35 are used as locating bearings to accommodate radial and axial loads, the
equivalent dynamic bearing load can be
obtained from
tion of all ball and roller bearings they

must always be subjected to a given
minimum load.
P = Fr when Fa / Fr 1.14
P = 0.35 Fr + 0.57 Fa when Fa / Fr > 1.14
where
Fr = radial load acting on the bearing
Fa = axial load acting on the bearing
P = Fr + 0.66 Fa
when Fa / Fr 0.95
P = 0.6 Fr + 1.07 Fa
when Fa / Fr > 0.95
When determining the axial force Fa

reference should be made to the following
section.
It should be remembered that satisfactory

performance of the ball set of four-point
contact ball bearings is only obtained when the
balls are in contact with the raceways at two
points, i.e. when the axial load

bearings mounted in pairs, back-toback or face-to-face
Fa 1.27 Fr
P = Fr + 0.55 Fa
when Fa / Fr 1.14
P = 0.57 Fr + 0.93 Fa
when Fa / Fr > 1.14
Fa and Fr are the forces acting on the
bearing pair.

double row bearings
If the four-point contact ball bearing is used

as a thrust bearing in combination with other
radial bearings, and it is mounted with radial
clearance in the housing, the equivalent
dynamic bearing load becomes
P = 1.07 Fa
In order to provide satisfactory opera-
This is also true of angular contact ball bearings, particularly if they run at high speeds
where the inertia forces of the balls and cage,
and the friction in the lubricant can have a
detrimental influence on the rolling conditions
in the bearing and may cause damaging sliding
movements to occur between the balls and the
raceways.
SKF Applications Engineering. However, the
weight of the components supported by the
bearing, together with the external forces, often
exceeds the requisite minimum load. If this is
not the case, an additional radial load must be
applied to the bearing; for example, by increasing belt tension, by applying a preload to the
inner or outer rings, or by using springs.

For the double row angular contact bearings

described in this catalog, the equivalent
dynamic bearing load is
P = XFr + YFa
where
X = radial load factor for the bearing
Y = axial load factor for the bearing
Fr = actual radial bearing load
Fa = actual axial bearing load
X and Y factors are given for each bearing in
Table 6a for Conrad type and Table 6b for Max
type they change depending on the load ratio
Fa / Fr in relationship to the reference value e.
59

Introduction
Table 6a
Calculation factors for double row angular contact ball bearings,
Conrad type
Designation
Dynamic
Static
Fa / Fr e
60
Fa / Fr e
Y0
3200 A
0.80
0.78
0.63
1.24
0.66
3201 A
0.80
0.78
0.63
1.24
0.66
3202 A
0.80
0.78
0.63
1.24
0.66
3203 A
0.80
0.78
0.63
1.24
0.66
3204 A
0.80
0.78
0.63
1.24
0.66
3205 A
0.80
0.78
0.63
1.24
0.66
3206 A
0.80
0.78
0.63
1.24
0.66
3207 A
0.80
0.78
0.63
1.24
0.66
3208 A
0.80
0.78
0.63
1.24
0.66
3209 A
0.80
0.78
0.63
1.24
0.66
3210 A
0.80
0.78
0.63
1.24
0.66
3211 A
0.80
0.78
0.63
1.24
0.66
3212 A
0.80
0.78
0.63
1.24
0.66
3213 A
0.80
0.78
0.63
1.24
0.66
3214 A
0.80
0.78
0.63
1.24
0.66
3215 A
0.80
0.78
0.63
1.24
0.66
3216 A
0.80
0.78
0.63
1.24
0.66
3217 A
0.80
0.78
0.63
1.24
0.66
3218 A
0.80
0.78
0.63
1.24
0.66
3219 A
0.80
0.78
0.63
1.24
0.66
3220 A
0.80
0.78
0.63
1.24
0.66
3304 A
0.80
0.78
0.63
1.24
0.66
3305 A
0.80
0.78
0.63
1.24
0.66
3306 A
0.80
0.78
0.63
1.24
0.66
3307 A
0.80
0.78
0.63
1.24
0.66
3308 A
0.80
0.78
0.63
1.24
0.66
3309 A
0.80
0.78
0.63
1.24
0.66
3310 A
0.80
0.78
0.63
1.24
0.66
3311 A
0.80
0.78
0.63
1.24
0.66
3312 A
0.80
0.78
0.63
1.24
0.66
3313 A
0.80
0.78
0.63
1.24
0.66
3314 A
0.80
0.78
0.63
1.24
0.66
3315 A
0.80
0.78
0.63
1.24
0.66
3316 A
0.80
0.78
0.63
1.24
0.66
3317 A
0.80
0.78
0.63
1.24
0.66
3318 A
0.80
0.78
0.63
1.24
0.66
Introduction
Table 6b
Calculation factors for double row angular contact ball bearings,
Max type
Designation
Dynamic
Static
Fa / Fr e
Fa / Fr e
Y0
3204 E
0.68
0.92
0.67
1.44
0.76
3205 E
0.68
0.92
0.67
1.44
0.76
3206 E
0.68
0.92
0.67
1.44
0.76
3207 E
0.80
0.78
0.63
1.24
0.66
3208 E
0.80
0.78
0.63
1.24
0.66
3209 E
0.80
0.78
0.63
1.24
0.66
3210 E
0.80
0.78
0.63
1.24
0.66
3211 E
0.80
0.78
0.63
1.24
0.66
3212 E
0.80
0.78
0.63
1.24
0.66
3213 E
0.80
0.78
0.63
1.24
0.66
3214 E
0.80
0.78
0.63
1.24
0.66
3215 E
0.80
0.78
0.63
1.24
0.66
3216 E
0.80
0.78
0.63
1.24
0.66
3217 E
0.80
0.78
0.63
1.24
0.66
3218 E
0.80
0.78
0.63
1.24
0.66
3304 E
0.80
0.78
0.63
1.24
0.66
3305 E
0.80
0.78
0.63
1.24
0.66
3306 E
0.80
0.78
0.63
1.24
0.66
3307 E
0.80
0.78
0.63
1.24
0.66
3308 E
0.80
0.78
0.63
1.24
0.66
3309 E
0.80
0.78
0.63
1.24
0.66
3310 E
0.80
0.78
0.63
1.24
0.66
3311 E
0.80
0.78
0.63
1.24
0.66
3312 E
0.80
0.78
0.63
1.24
0.66
3313 E
0.80
0.78
0.63
1.24
0.66
3314 E
0.80
0.78
0.63
1.24
0.66
3315 E
0.80
0.78
0.63
1.24
0.66
3316 E
0.80
0.78
0.63
1.24
0.66
61

Single row
Series: 7200 BE 7248 B
Size: 10 mm 240 mm
0.3937 in 9.4488 in
These bearings are typically mounted in pairs. Refer to page 52 for details.
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
mm
in
7200 BE
7201 BE
7202 BE
10
12
15
0.3937
0.4724
0.5906
30
32
35
1.1811
1.2598
1.3780
9
10
11
7203 BE
7204 BE
7205 BE
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
7206 BE
7207 BE
7208 BE
30
35
40
1.1811
1.3780
1.5748
62
72
80
7209 BE
7210 BE
7211 BE
45
50
55
1.7717
1.9685
2.1654
7212 BE
7213 BE
7214 BE
60
65
70
7215 BE
7216 BE
7217 BE
Dynamic
C
Speed rating
Static
C0
Reference
speed
r/min
Limiting
speed
r/min
lbf
lbf
0.3543
0.3937
0.4331
7 020
7 610
8 840
1 580
1 710
1 990
3 350
3 800
4 800
750
850
1 080
30 000
26 000
24 000
12
14
15
0.4724
0.5512
0.5906
11 000
13 300
15 600
2 470
2 990
3 510
6 100
8 300
10 200
1 370
1 870
2 290
2.4409
2.8346
3.1496
16
17
18
0.6299
0.6693
0.7087
24 000
31 000
36 500
5 400
6 970
8 210
15 600
20 800
26 000
85
90
100
3.3465
3.5433
3.9370
19
20
21
0.7480
0.7874
0.8268
38 000
40 000
46 200
8 540
8 990
10 400
2.3622
2.5591
2.7559
110
120
125
4.3307
4.7244
4.9213
22
23
24
0.8661
0.9055
0.9449
61 000
66 300
72 000
75
80
85
2.9528
3.1496
3.3465
130
140
150
5.1181
5.5118
5.9055
25
26
28
0.9843
1.0236
1.1024
7218 BE
7219 BE
7220 BE
90
95
100
3.5433
3.7402
3.9370
160
170
180
6.2992
6.6929
7.0866
30
32
34
7221 BE
7222 BE
7224 B
105
110
120
4.1339
4.3307
4.7244
190
200
215
7.4803
7.8740
8.4646
7226 B
7228 B
7230 B
130
140
150
5.1181
5.5118
5.9055
230
250
270
7232 B
7234 B
7236 B
160
170
180
6.2992
6.6929
7.0866
7238 B
7248 B
190
240
7.4803
9.4488
Mass
kg
lb
30 000
26 000
24 000
0.03
0.04
0.05
0.07
0.08
0.10
22 000
18 000
17 000
22 000
19 000
17 000
0.07
0.11
0.14
0.15
0.24
0.31
3 510
4 680
5 840
14 000
12 000
11 000
14 000
12 000
11 000
0.21
0.30
0.39
0.46
0.66
0.86
28 000
30 500
38 000
6 290
6 860
8 540
10 000
9 000
7 500
10 000
9 000
8 000
0.44
0.51
0.66
0.97
1.12
1.46
13 700
14 900
16 200
45 500
54 000
60 000
10 200
12 100
13 500
7 500
6 300
6 700
7 500
6 700
6 700
0.85
1.10
1.18
1.88
2.43
2.61
70 200
85 000
95 600
15 800
19 100
21 500
64 000
73 500
83 000
14 400
16 500
18 700
5 600
5 600
5 000
6 000
5 600
5 300
1.29
1.59
1.99
2.80
3.50
4.40
1.1811
1.2598
1.3386
108 000
129 000
135 000
24 300
29 000
30 300
96 500
108 000
122 000
21 700
24 300
27 400
4 500
4 800
4 000
4 800
4 800
4 300
2.41
2.95
3.61
5.30
6.50
8.00
36
38
40
1.4173
1.4961
1.5748
148 000
153 000
165 000
33 300
34 400
37 100
137 000
153 000
163 000
30 800
34 400
36 600
3 800
3 600
3 400
4 000
3 800
3 600
4.18
4.95
5.89
9.20
10.90
13.00
9.0551
9.8425
10.6299
40
42
45
1.5748
1.6535
1.7717
186 000
199 000
216 000
41 800
44 700
48 600
193 000
196 000
224 000
43 400
44 100
50 400
3 200
2 800
2 600
3 400
3 000
2 800
6.76
8.83
10.80
14.90
19.50
23.80
290
310
320
11.4173
12.2047
12.5984
48
52
52
1.8898
2.0472
2.0472
255 000
281 000
291 000
57 300
63 200
65 400
236 000
270 000
320 000
53 100
60 700
71 900
2 400
2 400
2 200
2 600
2 400
2 400
13.60
16.70
17.60
30.00
36.80
38.80
340
440
13.3858
17.3228
55
72
2.1654
2.8346
307 000
364 000
69 000
81 800
355 000
540 000
79 800
121 400
2 000
1 600
2 200
1 700
21.90
49.00
48.30
108.00
62
Single row
Series: 7301 BE 7330 B
Size: 12 mm 150 mm
0.4724 in 5.9055 in
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
mm
in
7301 BE
7302 BE
7303 BE
12
15
17
0.4724
0.5906
0.6693
37
42
47
1.4567
1.6535
1.8504
12
13
14
0.4724
0.5118
0.5512
10 600
13 000
15 900
7304 BE
7305 BE
7306 BE
20
25
30
0.7874
0.9843
1.1811
52
62
72
2.0472
2.4409
2.8346
15
17
19
0.5906
0.6693
0.7480
7307 BE
7308 BE
7309 BE
35
40
45
1.3780
1.5748
1.7717
80
90
100
3.1496
3.5433
3.9370
21
23
25
7310 BE
7311 BE
7312 BE
50
55
60
1.9685
2.1654
2.3622
110
120
130
4.3307
4.7244
5.1181
7313 BE
7314 BE
7315 BE
65
70
75
2.5591
2.7559
2.9528
140
150
160
7316 BE
7317 BE
7318 BE
80
85
90
3.1496
3.3465
3.5433
7319 BE
7320 BE
7321 BE
95
100
105
7322 BE
7324 B
7326 B
7328 B
7330 B
Speed rating
Static
C0
lbf
Reference
speed
r/min
Limiting
speed
r/min
Mass
lbf
kg
lb
2 400
2 900
3 600
5 000
6 700
8 300
1 120
1 510
1 870
24 000
20 000
19 000
24 000
20 000
19 000
0.06
0.08
0.11
0.10
0.20
0.20
19 000
26 500
35 500
4 300
6 000
8 000
10 400
15 600
21 200
2 340
3 510
4 770
18 000
15 000
13 000
18 000
15 000
13 000
0.15
0.24
0.37
0.30
0.50
0.80
0.8268
0.9055
0.9843
41 500
50 000
61 000
9 300
11 200
13 700
24 500
33 500
41 500
5 510
7 530
9 300
11 000
10 000
9 000
11 000
10 000
9 000
0.49
0.68
0.90
1.10
1.50
2.00
27
29
31
1.0630
1.1417
1.2205
75 000
85 000
104 000
16 900
19 100
23 400
51 000
60 000
69 500
11 500
13 500
15 600
8 000
7 000
6 700
8 000
7 000
6 700
1.16
1.49
1.88
2.60
3.30
4.10
5.5118
5.9055
6.2992
33
35
37
1.2992
1.3780
1.4567
116 000
127 000
132 000
26 100
28 500
29 700
80 000
90 000
106 000
18 000
20 200
23 800
6 300
5 600
5 300
6 300
5 600
5 300
2.31
2.83
3.26
5.10
6.20
7.20
170
180
190
6.6929
7.0866
7.4803
39
41
43
1.5354
1.6142
1.6929
143 000
156 000
166 000
32 100
35 100
37 300
118 000
132 000
146 000
26 500
29 700
32 800
5 000
4 800
4 500
5 000
4 800
4 500
4.03
4.74
5.53
8.90
10.40
12.20
3.7402
3.9370
4.1339
200
215
225
7.8740
8.4646
8.8583
45
47
49
1.7717
1.8504
1.9291
180 000
216 000
203 000
40 500
48 600
45 600
163 000
190 000
208 000
36 600
42 700
46 800
4 300
4 000
3 400
4 300
4 000
3 600
6.41
8.00
9.12
14.10
17.60
20.10
110
120
130
4.3307
4.7244
5.1181
240
260
280
9.4488
10.2362
11.0236
50
55
58
1.9685
2.1654
2.2835
225 000
238 000
296 000
50 600
53 500
66 500
224 000
250 000
270 000
50 400
56 200
60 700
3 200
3 000
2 800
3 400
3 200
2 800
10.70
13.80
17.10
23.60
30.40
37.70
140
150
5.5118
5.9055
300
320
11.8110
12.5984
62
65
2.4409
2.5591
302 000
332 000
67 900
74 600
310 000
365 000
69 700
82 100
2 600
2 400
2 600
2 400
21.30
25.00
47.00
55.10
63

Single row
Standard
Series: 7334 B 7344 B
Size: 170 mm 220 mm
6.6929 in 8.6614 in
Series: 7405 B 7432

Size: 25 mm 160 mm
0.9843 in 6.2992 in
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
Mass
kg
lb
7334 B
7336 B
7338 B
170
180
190
6.6929
7.0866
7.4803
360
380
400
14.1732
14.9606
15.7480
72
75
78
2.8346
2.9528
3.0709
390 000
410 000
442 000
87 700
92 200
99 400
455 000
490 000
560 000
102 300
110 200
125 900
2 000
2 000
1 900
2 200
2 000
1 900
34.60
40.00
48.30
76.30
88.20
106.50
7340 B
7344 B
200
220
7.8740
8.6614
420
460
16.5354
18.1102
80
88
3.1496
3.4645
462 000
494 000
103 900
111 100
655 000
720 000
147 200
161 900
1 800
1 600
1 800
1 700
52.80
70.00
116.40
154.30
7405 B
7406 B
7407 B
25
30
35
0.9843
1.1811
1.3780
80
90
100
3.1496
3.5433
3.9370
21
23
25
0.8268
0.9055
0.9843
39 700
47 500
60 500
8 900
10 700
13 600
23 600
29 000
38 000
5 300
6 500
8 500
11 000
10 000
8 500
11 000
10 000
9 000
0.61
0.85
1.10
1.30
1.90
2.40
7408 B
7409 B
7410 B
40
45
50
1.5748
1.7717
1.9685
110
120
130
4.3307
4.7244
5.1181
27
29
31
1.0630
1.1417
1.2205
70 200
85 200
95 600
15 800
19 200
21 500
45 500
55 000
64 000
10 200
12 400
14 400
8 000
7 000
6 300
8 000
7 500
6 700
1.40
1.80
2.25
3.10
4.00
5.00
7411 B
7412 B
7413 B
55
60
65
2.1654
2.3622
2.5591
140
150
160
5.5118
5.9055
6.2992
33
35
37
1.2992
1.3780
1.4567
111 000
119 000
130 000
25 000
26 800
29 200
76 500
86 500
96 500
17 200
19 400
21 700
6 000
5 600
5 000
6 300
5 600
5 300
2.75
3.30
3.85
6.10
7.30
8.50
7414 B
7415 B
7416 B
70
75
80
2.7559
2.9528
3.1496
180
190
200
7.0866
7.4903
7.8740
42
45
48
1.6535
1.7717
1.8898
159 000
168 000
178 000
35 700
37 800
40 000
127 000
140 000
153 000
28 500
31 500
34 400
4 500
4 300
4 000
4 800
4 500
4 300
5.00
6.85
8.00
11.00
15.10
17.60
7417 B
7418
7419
85
90
95
3.3465
3.5433
3.7402
210
225
250
8.2677
8.8583
9.8425
52
54
55
2.0472
2.1260
2.1654
190 000
216 000
251 000
42 700
48 600
56 400
166 000
200 000
245 000
37 300
45 000
55 100
3 800
3 600
3 400
4 000
3 800
3 400
10.30
11.50
13.50
22.70
25.40
29.80
100
160
3.9370
6.2992
265
400
10.4331
15.7480
60
88
2.3622
3.4646
276 000
468 000
62 000
105 200
275 000
610 000
61 800
137 100
3 200
2 200
3 200
2 200
15.50
59.14
34.20
130.40
7420
7432
64
Single row
Four-point ACBB
Series: QJ 202 N2MA QJ 252 N2MA
Size: 15 mm 260 mm
0.5906 in 10.2362 in
"N2" Design
N2 Design
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
mm
in
QJ 202 N2MA
QJ 203 N2MA
QJ 205 MA
15
17
25
0.5906
0.6693
0.9843
35
40
52
1.3780
1.5748
2.0472
11
12
15
QJ 206 MA
QJ 207 N2MA
QJ 208 MA
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409
2.8346
3.1496
QJ 209 MA
QJ 210 MA
QJ 211 MA
45
50
55
1.7717
1.9685
2.1654
85
90
100
QJ 212 MA
QJ 212 N2PHAS
QJ 213 MA
60
60
65
2.3622
2.3622
2.5591
QJ 214 MA
QJ 215 MA
QJ 216 MA
70
75
80
QJ 217 MA
QJ 218 N2MA
QJ 219 N2MA
Dynamic
C
Speed rating
Static
C0
lbf
Reference
speed
r/min
Limiting
speed
r/min
Mass
lbf
kg
lb
0.4331
0.4724
0.5906
12 700
15 900
27 000
2 850
3 570
6 070
8 300
10 600
21 200
1 870
2 380
4 770
22 000
19 000
16 000
36 000
30 000
22 000
0.06
0.08
0.16
0.14
0.18
0.35
16
17
18
0.6299
0.6693
0.7087
37 500
49 000
56 000
8 430
11 020
12 590
30 500
41 500
49 000
6 860
9 330
11 020
14 000
12 000
11 000
19 000
17 000
15 000
0.24
0.36
0.45
0.53
0.79
0.99
3.3465
3.5433
3.9370
19
20
21
0.7480
0.7874
0.8268
63 000
65 500
85 000
14 160
14 720
19 110
56 000
61 000
83 000
12 590
13 710
18 660
10 000
9 000
8 000
14 000
13 000
11 000
0.52
0.59
0.77
1.15
1.30
1.70
110
110
120
4.3307
4.3307
4.7244
22
22
23
0.8661
0.8661
0.9055
96 500
96 500
110 000
21 690
21 690
24 730
93 000
93 000
112 000
20 910
20 910
25 180
7 500
8 500
6 700
10 000
10 000
9 500
0.99
0.89
1.20
2.18
1.96
2.60
2.7559
2.9528
3.1496
125
130
140
4.9213
5.1181
5.5118
24
25
26
0.9449
0.9843
1.0236
120 000
125 000
146 000
27 000
28 100
32 800
122 000
132 000
156 000
27 430
29 670
35 100
6 300
6 300
5 600
9 000
8 500
8 000
1.32
1.45
1.85
2.90
3.20
4.10
85
90
95
3.3465
3.5433
3.7402
150
160
170
5.9055
6.2992
6.6929
28
30
32
1.1024
1.1811
1.2598
156 000
186 000
212 000
35 100
41 800
47 700
173 000
200 000
232 000
38 900
45 000
52 200
5 300
5 000
4 800
7 500
7 000
6 700
2.25
2.75
3.35
5.00
6.10
7.40
QJ 220 N2MA
QJ 222 N2MA
QJ 224 N2MA
100
110
120
3.9370
4.3370
4.7244
180
200
215
7.0866
7.8740
8.4646
34
38
40
1.3386
1.4961
1.5748
236 000
280 000
300 000
53 100
62 900
67 400
265 000
325 000
365 000
59 600
73 100
82 100
4 500
4 000
3 600
6 300
5 600
5 000
4.05
5.60
6.95
8.90
12.30
15.30
QJ 226 N2MA
QJ 228 N2MA
QJ 230 N2MA
130
140
150
5.1181
5.5118
5.9055
230
250
270
9.0551
9.8425
10.6299
40
42
45
1.5748
1.6535
1.7717
310 000
345 000
400 000
69 700
77 600
89 900
400 000
475 000
570 000
89 900
106 800
128 100
3 400
3 200
3 000
4 800
4 300
4 000
7.75
9.85
12.50
17.10
21.70
27.60
QJ 232 N2MA
QJ 234 N2MA
QJ 236 N2MA
160
170
180
6.2992
6.6929
7.0866
290
310
320
11.4173
12.2047
12.5984
48
52
52
1.8898
2.0472
2.0472
450 000
455 000
475 000
101 200
102 300
106 800
670 000
720 000
765 000
150 600
161 900
172 000
2 800
2 600
2 400
3 800
3 400
3 400
15.50
19.50
20.50
34.20
43.00
45.20
QJ 240 N2MA
QJ 248 N2MA
QJ 252 N2MA
200
240
260
7.8740
9.4488
10.2362
360
440
480
14.1732
17.3228
18.8976
58
72
80
2.2835
2.8346
3.1496
540 000
650 000
728 000
121 400
146 100
163 700
915 000
1 200 000
1 430 000
205 700
269 800
321 500
1 800
1 500
1 300
3 000
2 400
2 200
28.50
53.00
68.00
62.80
116.80
149.90
65

Single row
Four-point ACBB
Size: 17 mm 220 mm
0.6693 in 8.6614 in
"N2" Design
N2 Design
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
mm
in
QJ 303 N2MA
QJ 304 MA
QJ 305 MA
17
20
25
0.6693
0.7874
0.9843
47
52
62
1.8504
2.0472
2.4409
14
15
17
0.5512
0.5906
0.6693
QJ 306 MA
QJ 307 MA
QJ 308 MA
30
35
40
1.1811
1.3780
1.5748
72
80
90
2.8346
3.1496
3.5433
19
21
23
QJ 309 MA
QJ 310 MA
QJ 311 MA
45
50
55
1.7717
1.9685
2.1654
100
110
120
3.9370
4.3307
4.7244
QJ 312 MA
QJ 313 MA
QJ 314 MA
60
65
70
2.3622
2.5591
2.7559
130
140
150
QJ 315 N2MA
QJ 316 N2MA
QJ 317 N2MA
75
80
85
2.9528
3.1496
3.3465
QJ 318 N2MA
QJ 319 N2MA
QJ 320 N2MA
90
95
100
QJ 322 N2MA
QJ 324 N2MA
QJ 326 N2MA
Dynamic
C
N
Speed rating
Static
C0
Reference
speed
r/min
Limiting
speed
r/min
lbf
lbf
23 400
32 000
39 000
5 260
7 190
8 770
15 000
21 600
28 000
3 370
4 860
6 290
17 000
18 000
12 000
0.7480
0.8268
0.9055
53 000
64 000
78 000
11 910
14 390
17 530
41 500
51 000
64 000
9 330
11 460
14 390
25
27
29
0.9843
1.0630
1.1417
100 000
118 000
137 000
22 480
26 530
30 800
83 000
100 000
118 000
5.1181
5.5118
5.9055
31
33
35
1.2205
1.2992
1.3780
156 000
176 000
200 000
35 100
39 600
45 000
160
170
180
6.2992
6.6929
7.0866
37
39
41
1.4567
1.5354
1.6142
216 000
232 000
250 000
3.5433
3.7402
3.9370
190
200
215
7.4803
7.8740
8.4646
43
45
47
1.6929
1.7717
1.8504
110
120
130
4.3307
4.7244
5.1181
240
260
280
9.4488
10.2362
11.0236
50
55
58
QJ 328 N2MA
QJ 330 N2MA
QJ 332 N2MA
140
150
160
5.5118
5.9055
6.2992
300
320
340
11.8110
12.5984
13.3858
QJ 334 N2MA
QJ 336 N2MA
QJ 338 N2MA
170
180
190
6.6929
7.0866
7.4803
360
380
400
QJ 344 N2/309829 220

QJ 344 N2MA 220
8.6614
8.6614
460
460
Mass
kg
lb
28 000
24 000
20 000
0.14
0.18
0.29
0.30
0.40
0.60
12 000
11 000
10 000
17 000
15 000
14 000
0.42
0.57
0.78
0.90
1.30
1.70
18 700
22 500
26 500
9 000
8 000
7 000
12 000
11 000
10 000
1.05
1.35
1.75
2.30
3.00
3.90
137 000
156 000
180 000
30 800
35 100
40 500
6 700
6 300
5 600
9 000
8 500
8 000
2.15
2.70
3.15
4.70
6.00
6.90
48 600
52 200
56 200
200 000
228 000
255 000
45 000
51 300
57 300
5 300
5 000
4 800
7 500
7 000
6 700
3.90
4.60
5.45
8.60
10.10
12.00
285 000
305 000
345 000
64 100
68 600
77 600
305 000
340 000
400 000
68 600
76 400
89 900
4 500
4 300
4 000
6 300
6 000
5 600
6.45
7.45
9.30
14.20
16.40
20.50
1.9685
2.1654
2.2835
390 000
415 000
455 000
87 700
93 300
102 300
480 000
530 000
610 000
107 900
119 100
137 100
3 600
3 200
3 000
4 800
4 500
4 000
12.50
16.00
19.50
27.60
35.30
43.00
62
65
68
2.4409
2.5591
2.6772
500 000
530 000
570 000
112 400
119 100
128 100
695 000
765 000
880 000
156 200
172 000
197 800
2 800
2 600
2 400
3 800
3 600
3 400
24.00
29.00
34.50
52.90
63.90
76.10
14.1732
14.9606
15.7480
72
75
78
2.8346
2.9528
3.0709
655 000
680 000
702 000
147 200
152 900
157 800
1 040 000
1 020 000
1 116 000
233 800
229 300
250 900
2 200
2 200
1 700
3 200
3 000
2 800
41.50
47.50
49.00
91.50
104.70
108.00
18.1102
18.1102
88
88
3.4646
3.4646
904 000
780 000
203 200
175 300
1 660 000
1 400 000
373 200
314 700
1 500
1 500
2 400
2 400
78.00
78.00
172.00
172.00
66
Single row
Four-point ACBB
Standard
Size: 85 mm 440 mm
3.3465 in 17.3228 in
"N2" Design
N2 Design
Designation
Bore
d
mm
Width
B
mm
in
Dynamic
C
in
QJ 1017 N2MA
QJ 1021 N2MA
QJ 1022 N2MA
85
105
110
3.3465 130
4.1339 160
4.3307 170
5.1181
6.2992
6.6929
22
26
28
0.8661
1.0236
1.1024
85 200
124 000
146 000
19 200
27 900
32 800
QJ 1030 N2MA
QJ 1032 N2MA
QJ 1038 N2MA
150
160
190
5.9055 225
6.2992 240
7.4803 290
8.8583
9.4488
11.4173
35
38
46
1.3780
1.4961
1.8110
216 000
247 000
338 000
QJ 1040 N2MA
QJ 1056 N2MA
QJ 1060 MA
200
280
300
7.8740 310
11.0236 420
11.8110 460
12.2047
16.5354
18.1102
51
65
74
2.0079
2.5591
2.9134
QJ 1064 MA
QJ 1068 N2MA
QJ 1072 N2MA
320
340
360
12.5984 480
13.3858 520
14.1732 540
18.8976
20.4724
21.2598
74
82
82
QJ 1076 N2MA
QJ 1080 N2MA
QJ 1084 N2MA
380
400
420
14.9606 560
15.7480 600
16.5354 620
22.0472
23.6220
24.4094
QJ 1088 N2MA
QJ 1092 N2MA
QJ 1096 N2MA
440
460
480
17.3228 650
18.1102 680
18.8976 700
QJ 1240 N2MA
200
QJ 1244 N2MA
220
QJ 1248 MA/344524 240
Speed rating
lbf
Limiting
speed
r/min
102 000
156 000
186 000
22 900
35 100
41 800
5 000
4 000
3 800
8 000
6 700
6 300
1.10
2.00
2.50
2.40
4.40
5.50
48 600
55 500
76 000
305 000
355 000
510 000
68 600
79 800
114 600
2 800
2 600
2 200
4 500
4 300
3 400
5.25
6.45
11.50
11.57
14.20
25.40
390 000
553 000
650 000
87 700
124 300
146 100
620 000
1 060 000
1 340 000
139 400
238 300
301 200
2 000
1 400
1 300
3 200
2 400
2 200
15.00
33.50
47.50
33.10
73.90
104.70
2.9134
3.2283
3.2283
715 000
780 000
793 000
160 700
175 300
178 300
1 530 000
1 700 000
1 800 000
343 900
382 200
404 600
1 200
1 100
1 100
2 000
1 800
1 700
50.00
67.50
70.50
110.20
148.80
155.40
82
90
90
3.2283
3.5433
3.5433
819 000
904 000
923 000
184 100
203 200
207 500
1 900 000
2 160 000
2 280 000
427 100
485 600
512 500
1 000
950
900
1 700
1 500
1 500
73.50
95.50
99.50
162.00
210.50
219.40
25.5906
26.7717
27.5591
94
100
100
3.7008
3.9370
3.9370
995 000
1 040 000
1 060 000
223 700
233 800
238 300
2 500 000
2 650 000
2 800 000
562 000
595 700
629 400
850
800
750
1 400
1 300
1 300
115.00
130.00
135.00
253.50
286.60
297.60
7.8740 360
8.6614 400
9.4488 440
14.1732
15.7480
17.3228
70
78
85
2.7559
3.0709
3.3465
520 000
592 000
663 000
116 900
133 100
149 000
865 000
1 020 000
1 220 000
194 500
229 300
274 300
1 800
1 600
1 500
3 000
2 600
2 400
32.50
45.50
61.00
71.70
100.30
134.50
260
280
300
10.2362 480
11.0236 500
11.8110 540
18.8976
19.6850
21.2598
90
90
98
3.5433
3.5433
3.8583
741 000
728 000
832 000
166 600
163 700
187 000
1 460 000
1 460 000
1 760 000
328 200
328 200
395 600
1 300
1 300
1 200
2 200
2 000
1 900
78.00
82.00
105.00
172.00
180.80
231.50
QJ 1264 N2MA
320
QJ 1268 MA/344524 340
QJ 1272 N2MA
360
12.5984 580
13.3858 620
14.1732 650
22.8346
24.4094
25.5906
105
118
122
4.1339
4.6457
4.8031
923 000
1 060 000
1 110 000
207 500
238 300
249 500
2 040 000
2 450 000
2 600 000
458 600
550 800
584 500
1 100
1 000
950
1 700
1 600
1 500
130.00
165.00
190.00
286.60
363.80
418.90
QJ 1276 N2MA
QJ 1280 N2MA
QJ 1284 N2MA
380
400
420
14.9606 680
15.7480 720
16.5354 760
26.7717
28.3465
29.9213
132
140
150
5.1969
5.5118
5.9055
1 170 000
1 300 000
1 430 000
263 000
292 200
321 500
2 850 000
3 250 000
3 750 000
640 700
730 600
843 000
900
800
750
1 400
1 300
1 300
220.00
265.00
315.00
485.00
584.20
694.50
QJ 1288 N2MA
QJ 1292 N2MA
QJ 1296 N2MA
440
460
480
17.3228 790
18.1102 830
18.8976 870
31.1024
32.6772
34.2520
155
165
170
6.1024
6.4961
6.6929
1 400 000
1 530 000
1 680 000
314 700
343 900
377 700
3 750 000
4 250 000
4 750 000
843 000
955 400
1 068 000
750
700
670
1 200
1 100
1 100
350.00
415.00
470.00
771.60
914.90
1 036.20
QJ 1984 MA
QJ 1988 N2MA
420
440
16.5354 560
17.3228 600
22.0472
23.6220
65
74
2.5591
2.9134
637 000
761 000
143 200
171 100
1 600 000
1 900 000
359 700
427 100
950
900
1 600
1 500
51.00
65.00
112.40
143.30
Static
C0
Mass
Reference
speed
r/min
QJ 1252 MA
QJ 1256 N2MA
QJ 1260 N2MA
Outside diameter
D
mm
in
Basic load ratings
lbf
kg
lb
67

B
Thrust pack
Double row
Four-point ACBB and Single row ACBB
Standard
Series: BA2B 459304 BA2B 459328
Size: 20 mm 140 mm
0.7874 in 5.5118 in
Series: BA2B 459418 BA2B 459430

Size: 90 mm 150 mm
3.5433 in 5.9055 in
BA2B
4593XX
BA2B 4593XX
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference
speed
r/min
Mass
Limiting
speed
r/min
kg
lb
BA2B 459304
BA2B 459306
BA2B 459307
20
30
35
0.7874
1.1811
1.3780
52
72
80
2.0472
2.8346
3.1496
30
38
42
1.1811
1.4961
1.6535
30 700
55 900
62 400
6 900
12 600
14 000
20 800
42 500
49 000
4 680
9 550
11 000
9 000
6 700
6 000
13 000
9 000
8 000
0.28
0.68
0.90
0.62
1.50
2.00
BA2B 459308
BA2B 459309
BA2B 459310
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
46
50
54
1.8110
1.9685
2.1260
79 300
97 500
119 000
17 800
21 900
26 800
65 500
81 500
102 000
14 700
18 300
22 900
5 300
4 800
4 300
7 000
6 300
5 600
1.25
1.70
2.20
2.75
3.75
4.85
BA2B 459311
BA2B 459312
BA2B 459313
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
58
62
65
2.2835
2.4409
2.5984
138 000
156 000
174 000
31 000
35 100
39 100
120 000
140 000
160 000
27 000
31 500
36 000
3 800
3 600
3 200
5 000
4 800
4 300
2.80
3.50
4.30
6.15
7.70
9.50
BA2B 459314
BA2B 459317
BA2B 459318
70
85
90
2.7559
3.3465
3.5433
150
180
190
5.9055
7.0866
7.4803
70
82
86
2.7559
3.2283
3.3858
195 000
251 000
270 000
43 800
56 400
60 700
180 000
265 000
290 000
40 500
59 600
65 200
3 000
2 400
2 200
4 000
3 400
3 200
5.30
8.90
10.50
11.50
19.50
23.00
BA2B 459320
BA2B 459322
BA2B 459326
100
110
130
3.9370
4.3307
5.1181
215
240
280
8.4646
9.4488
11.0236
94
100
116
3.7008
3.9370
4.5669
325 000
364 000
403 000
73 100
81 800
90 600
380 000
450 000
540 000
85 400
101 000
121 000
1 900
1 700
1 500
2 800
2 400
2 000
15.00
20.00
35.00
33.00
44.00
77.00
BA2B 459328
140
5.5118
300
11.8110
124
4.8819
449 000
101 000
620 000
139 000
1 400
1 900
43.00
95.00
BA2B 459418
BA2B 459420
BA2B 459422
90
100
110
3.5433
3.9370
4.3307
160
180
200
6.2992
7.0866
7.8740
60
68
76
2.3622
2.6772
2.9921
178 000
221 000
260 000
40 000
49 700
58 500
193 000
245 000
310 000
43 400
55 100
69 700
2 600
2 200
1 900
3 600
3 200
2 800
4.60
6.60
9.20
10.00
14.50
20.50
BA2B 459424
BA2B 459428
BA2B 459430
120
140
150
4.7244
5.5118
5.9055
215
250
270
8.4646
9.8425
10.6299
80
84
90
3.1496
3.3071
3.5433
270 000
296 000
319 000
60 700
66 500
71 700
325 000
390 000
44 0000
73 100
87 700
98 900
1 700
1 600
1 500
2 400
2 200
2 000
12.20
17.70
23.00
27.00
39.00
50.50
68
Double row, 40 contact angle

Standard
Series: 3308 DNRCBM 3313 DNRCBM
Size: 40 mm 65 mm
1.5748 in 2.5591 in
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
Mass
mm
in
kg
lb
3308 DNRCBM
3309 DNRCBM
3310 DNRCBM
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
36.5
39.7
44.4
1.437
1.563
1.748
49 400
61 800
81 900
11 100
13 900
18 400
41 500
52 000
69 500
9 300
11 700
15 600
6 700
6 000
5 300
7 000
6 300
5 600
1.20
1.50
1.95
2.60
3.30
4.30
3311 DNRCBM
3313 DNRCBM
55
65
2.1654
2.5591
120
140
4.7244
5.5118
49.2
58.7
1.937
2.311
95 600
138 000
21 500
31 000
83 000
122 000
18 700
27 400
4 800
4 300
5 000
4 500
2.55
4.00
5.60
8.80
69

Conrad
Series: 3200 A 3220 A
Size: 10 mm 100 mm
0.3937 in 3.9370 in
A-Open
A-Z
A-N
A-Z
A-N
A-2Z
A-NR
A-2Z
A-NR
A-Open
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
mm
in
3200 A
3201 A
3202 A
10
12
15
0.3937
0.4724
0.5906
30
32
35
1.1811
1.2598
1.3780
14.0
15.9
15.9
3203 A
3204 A
3205 A
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
3206 A
3207 A
3208 A
30
35
40
1.1811
1.3780
1.5748
62
72
80
3209 A
3210 A
3211 A
45
50
55
1.7717
1.9685
2.1654
3212 A
3213 A
3214 A
60
65
70
3215 A
3216 A
3217 A
3218 A
3219 A
3220 A
Dynamic
C
Speed rating
Sealed
Static
C0
N
lbf

speed
speed
speed
r/min r/min r/min
kg
lb
lbf
.5625
.6250
.6250
7 610
10 100
11 200
1 700
2 300
2 500
4 300
5 600
6 800
1 000
1 300
1 500
22 000 24 000
20 000 22 000
17 000 18 000
17 000
15 000
14 000
0.05
0.06
0.07
0.11
0.13
0.15
17.5
20.6
20.6
.6875
.8125
.8125
14 300
20 000
21 600
3 200
4 500
4 900
8 800
12 000
14 300
2 000
2 700
3 200
15 000 16 000
14 000 14 000
12 000 12 000
12 000
10 000
8 500
0.10
0.16
0.19
0.21
0.35
0.42
2.4409
2.8346
3.1496
23.8
27.0
30.2
.9375
1.0625
1.1875
30 000
40 000
47 500
6 700
9 000
10 700
20 400
28 000
34 000
4 600
6 300
7 600
10 000 10 000
9 000 9 000
8 000 8 000
7 500
6 300
5 600
0.29
0.40
0.58
0.64
0.88
1.28
85
90
100
3.3465
3.5433
3.9370
30.2
30.2
33.3
1.1875
1.1875
1.3125
51 000
51 000
60 000
11 500
11 500
13 500
39 000
39 000
47 500
8 800
8 800
10 700
7 500
7 000
6 300
7 500
7 000
6 300
5 300
4 800
4 500
0.64
0.66
1.05
1.41
1.46
2.31
2.3622
2.5591
2.7559
110
120
125
4.3307
4.7244
4.9213
36.5
38.1
39.7
1.4375
1.5000
1.5625
73 500
80 600
88 400
16 500
18 100
19 900
58 500
73 500
80 000
13 200
16 500
18 000
5 600
4 500
4 300
5 600
4 800
4 500
4 000
3 600
1.40
1.75
1.90
3.09
3.86
4.19
75
80
85
2.9528
3.1496
3.3465
130
140
150
5.1181
5.5118
5.9055
41.3
44.4
49.2
1.6250
1.7500
1.9375
95 600
106 000
124 000
21 500
23 800
27 900
88 000
95 000
110 000
19 800
21 400
24 700
4 300
4 000
3 600
4 500
4 300
3 800
3 200
3 000
2.10
2.65
3.40
4.63
5.84
7.50
90
95
100
3.5433
3.7402
3.9370
160
170
180
6.2992
6.6929
7.0866
52.4
55.6
60.3
2.0625
2.1875
2.3750
130 000
159 000
178 000
29 200
35 700
40 000
120 000
146 000
166 000
27 000
32 800
37 300
3 400
3 200
3 000
3 600
3 400
3 200
4.15
5.00
6.10
9.15
11.02
13.45
Note: The 5200/5300 series DRACBB have been replaced with the 3200/3300 series designation.
The product design has not changed; therefore, the fit, form and function remain the same.
70
Mass

Conrad
Series: 3304 A 3318 A
Size: 20 mm 90 mm
0.7874 in 3.5433 in
A-Open
A-Open
Designation
A-RS1
A-Z
A-N
A-RS1
A-Z
A-N
A-2RS1
A-2Z
A-NR
A-2RS1
A-2Z
A-NR
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
mm
in
3304 A
3305 A
3306 A
20
25
30
0.7874
0.9843
1.1811
52
62
72
2.0472
2.4409
2.8346
22.2
25.4
30.2
3307 A
3308 A
3308 AH
35
40
40
1.3780
1.5748
1.5748
80
90
90
3.1496
3.5433
3.5433
3309 A
3309 AH
3310 A
45
45
50
1.7717
1.7717
1.9685
100
100
110
3310 AH
3311 A
3311 AH
50
55
55
1.9685
2.1654
2.1654
3312 A
3313 A
3314 A
60
65
70
3315 A
3315 AH
3316 A
3317 A
3318 A
Dynamic
C
Speed rating
Sealed
Static
C0
N
Mass
lbf

speed
speed
speed
r/min r/min r/min
kg
lb
13 000 13 000
11 000 11 000
9 000 9 000
9 000
7 500
6 300
0.20
0.31
0.59
0.44
0.68
1.30
lbf
.8750
1.0000
1.1875
23 600
32 000
41 500
5 300
7 200
9 300
14 600
20 400
27 500
3 300
4 600
6 200
34.9
36.5
36.5
1.3750
1.4375
1.4375
52 000
64 000
64 000
11 700
14 400
14 400
35 500
44 000
44 000
8 000
9 900
9 900
8 500
7 500
7 500
8 500
7 500
7 500
6 000
5 000
0.71
1.05
1.05
1.57
2.31
2.31
3.9370
3.9370
4.3307
39.7
39.7
44.4
1.5625
1.5625
1.7500
75 000
75 000
90 000
16 900
16 900
20 200
53 000
53 000
64 000
11 900
11 900
14 400
6 700
6 700
6 000
6 700
6 700
6 000
4 800
4 300
1.40
1.40
1.95
3.09
3.09
4.30
110
120
120
4.3307
4.7244
4.7244
44.4
49.2
49.2
1.7500
1.9375
1.9375
90 000
112 000
112 000
20 200
25 200
25 200
64 000
81 500
81 500
14 400
18 300
18 300
6 000
5 300
5 300
6 000
5 300
5 300
1.95
2.55
2.55
4.30
5.62
5.62
2.3622
2.5591
2.7559
130
140
150
5.1181
5.5118
5.9055
54.0
58.7
63.5
2.1250
2.3125
2.5000
127 000
146 000
153 000
28 500
32 800
34 400
95 000
110 000
125 000
21 400
24 700
28 100
5 000
4 500
4 000
5 000
4 500
4 000
3.25
4.10
5.05
7.16
9.04
11.13
75
75
80
2.9528
2.9528
3.1496
160
160
170
6.2992
6.2992
6.6929
68.3
68.3
68.3
2.6875
2.6875
2.8675
176 000
176 000
182 000
39 600
39 600
40 900
140 000
140 000
156 000
31 500
31 500
35 100
4 000
4 000
3 400
4 000
4 000
3 600
5.60
5.60
6.80
12.35
12.35
14.99
85
90
3.3465
3.5433
180
190
7.0866
7.4803
73.0
73.0
2.8750
2.8750
195 000
195 000
43 800
43 800
176 000
180 000
39 600
40 500
3 200
3 000
3 400
3 200
8.30
9.25
18.30
20.39
71

Max type
Standard
Series: 3205 E 3218 E
Size: 25 mm 90 mm
0.9843 in 3.5433 in
E-RS1
E-Z
E-N
E-RS1
E-Z
E-N
Series: 3305 E 3316 E

Size: 25 mm 80 mm
0.9843 in 3.1496 in
E-OPEN
E-Open
Designation
Bore
d
Outside diameter
D
mm
in
E-2RS1
E-2Z
E-2RS1
E-2Z
Basic load ratings

Width
B
mm
in
mm
in
3205 E
3206 E
3207 E
25
30
35
0.9843
1.1811
1.3780
52
62
72
2.0472
2.4409
2.8346
20.6
23.8
27.0
3208 E
3209 E
3210 E
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1496
3.3465
3.5433
3211 E
3212 E
3213 E
55
60
65
2.1654
2.3622
2.5591
100
110
120
3214 E
3215 E
3216 E
70
75
80
2.7559
2.9528
3.1496
3217 E
3218 E
85
90
3305 E
3306 E
3307 E
Dynamic
C
Speed rating
Sealed
Static
C0
N
E-NR
E-NR
Mass
lbf

speed
speed
speed
r/min r/min r/min
kg
lb
11 000 12 000
9 500 10 000
8 000 8 500
8 500
7 500
6 300
0.25
0.35
0.54
0.55
0.80
1.20
lbf
.8125
.9375
1.0625
22 900
30 300
39 100
5 150
6 810
8 790
21 200
28 000
36 500
4 770
6 290
8 210
30.2
30.2
30.2
1.1875
1.1875
1.1875
49 500
51 200
53 900
11 130
11 510
12 120
49 000
54 000
58 500
11 020
12 140
13 150
7 500
6 700
6 300
8 000
7 000
6 700
5 600
5 300
4 800
0.73
0.77
0.82
1.60
1.70
1.80
3.9370
4.3307
4.7244
33.3
36.5
38.1
1.3125
1.4375
1.5000
66 000
78 100
88 000
14 840
17 560
19 780
76 500
88 000
106 000
17 200
19 780
23 800
5 600
5 000
4 800
6 000
5 300
5 000
4 500
4 000
3 600
1.15
1.50
1.95
2.50
3.30
4.30
125
130
140
4.9213
5.1181
5.5118
39.7
41.3
44.4
1.5625
1.6250
1.7500
101 000
108 000
128 000
22 700
24 300
28 800
125 000
137 000
160 000
28 100
30 800
36 000
4 500
4 300
4 000
4 800
4 500
4 000
3.3465
3.5433
150
160
5.9055
6.2992
49.2
52.4
1.9375
2.0625
142 000
151 000
31 900
33 900
176 000
193 000
39 600
43 400
3 600
3 400
25
30
35
0.9843
1.1811
1.3780
62
72
80
2.4409
2.8346
3.1496
25.4
30.2
34.9
1.0000
1.1875
1.3750
34 100
46 800
52 300
7 670
10 520
11 760
30 500
43 000
48 000
6 860
9 670
10 790
3308 E
3309 E
3310 E
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
36.5
39.7
44.4
1.4375
1.5625
1.7500
67 100
80 900
95 200
15 080
18 190
21 400
65 500
80 000
95 000
14 720
17 980
21 360
6 700
6 000
5 300
3311 E
3312 E
3313 E
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
49.2
54.0
58.7
1.9375
2.1250
2.3125
119 000
134 000
182 000
26 800
30 100
40 900
122 000
143 000
163 000
27 400
32 100
36 600
3314 E
3315 E
3316 E
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
63.5
68.3
68.3
2.5000
2.6875
2.6875
172 000
187 000
201 000
38 700
42 000
45 200
186 000
208 000
236 000
41 800
46 800
53 100
2.15
2.50
3.00
4.70
5.50
6.60
3 800
3 600
3 200
3 000
3.70
4.55
8.16
10.00
10 000 10 000
8 500 9 000
7 500 8 000
7 500
6 300
6 000
0.39
0.59
0.86
0.90
1.30
1.90
7 000
6 300
5 600
5 000
4 800
1.15
1.50
2.00
2.50
3.30
4.40
5 000
4 500
4 300
5 300
4 800
4 500
2.65
3.30
4.20
5.80
7.30
9.30
4 000
3 600
3 400
4 300
3 800
3 600
5.00
6.35
7.25
11.00
14.00
16.00
72
Self-aligning
ball bearings
Nomenclature
1220 _K M C3
4
2
1
1. Internal design:
3. Cage designs:
Standard internal design
TN9
Improved internal design
Injection molded polyamide

6.6 cage with glass fiber
reinforcement
Machined brass cage
TN
Injection molded polyamide

6.6 cage
2. Variations:
4. Clearance:
Bearing with 1 to 12
tapered bore
C2

< Normal
2RS1
Contact seal acrylonitrile

butadine rubber (NBR) with
sheet steel on both sides
of bearing
(C0)*
Normal radial internal

clearance
C3

> Normal
C4

> C3
KAM
Bearing kit, includes bearing

and adapter sleeve
*Not marked on bearing or package
73
Self-aligning ball bearings
Product
Details
Technical
features
Boundary dimensions
Tolerances
ABEC 1, ISO 492-2002
Max. temperature
248 F (120 C) for open bearings only
Misalignment
Series
Series
Series
Series
Series
Series
Series
Series
Series
Cage material
Standard
Optional
Axial load max
for adapter
sleeve
mounting
3.0
2.5
3.0
2.5
1.5
3.0
1.5
2.5
3.0
Polyamide (TN)
Glass fiber reinforced polyamide (TN9)
Machined brass (M) large bearings
Fap = 3 x B x d where
B = bearing width in mm
d = bearing bore in mm
Fap = axial load in Newtons
Seals
2RS1 synthetic rubber (NBR) seals
Grease
Lithium soap with mineral oil
Self-aligning
ball bearing (open design)
74
108, 126, 127, 129, 135

12 (E)
13 (E)
22 (E)
22 E-2RS1
23 (E)
23 E-2RS1
112 (E)
130, 139
Self-aligning
ball bearing (sealed design)
degrees
degrees
degrees
degrees
degrees
degrees
degrees
degrees
degrees
Introduction
Introduction
Variations
Self-aligning ball bearings have two rows

of balls with a common sphered raceway
in the outer ring. This feature gives the bearings their self-aligning property, permitting
angular misalignment of the shaft relative to
the housing. Therefore, they are particularly
suitable for applications where misalignment
can arise from errors in mounting or from
shaft deflection.
For applications where the load carrying
capacity of self-aligning ball bearings is
insufficient, spherical roller bearings, which
have the same self-aligning property, should
be used instead.
SKF self-aligning ball bearings of the E
design have higher load carrying capacity than
bearings of the original standard design
because of improvements to the internal
design. This makes them suitable for a wider
range of applications than their predecessors;
the same size of bearing can be used to carry
heavier loads, or if the loads remain the same,
operational reliability is enhanced and bearing
life is longer. Self-aligning ball bearings of the
E design are fitted with a glass fiber reinforced
polyamide 6.6 cage (TN9) as standard.
SKF self-aligning ball bearings are available
in several designs of which the most common
are shown in this catalog:
Sealed bearings
Basic open (unsealed) design bearings

Bearings with seals on both sides
Basic design
Self-aligning ball bearings of the basic design
are available with a cylindrical bore as well as
with a tapered bore (taper 1:12).
For self-aligning ball bearings with a
tapered bore, SKF supplies appropriate
adapter sleeves with which the bearings can
be secured simply and rapidly to smooth or
stepped shafts. The adapter sleeves are supplied complete with nut and locking device.
Additional information can be found in the
Split Pillow Block sections (inch and metric)
under Mounted Accessories.
SKF self-aligning ball bearings are also available in a sealed (2RS1) version with rubbing
seals on both sides. The seals are made of oil
and acrylonitrile butadine rubber (NBR) and
have a sheet steel reinforcement. The operating temperature range for the seal material is
-40 to +248 F (-40 to +120 C). The outside diameter of the seal is retained in a
recess in the outer ring giving a tight seal
without deformation, while the lip of the seal
exerts a slight pressure against a recess in the
inner ring shoulder.
The sealed bearings are supplied as standard filled with a lithium base grease which
is suitable for the operating temperature
range -22 to +230 F (-30 to +110 C).
The bearings are lubricated for life and are
maintenance free. They should not be
heated at temperatures greater than 250 F
(120 C) prior to mounting and must on no
account be washed.
SKF self-aligning ball bearings with seals
are available with a cylindrical bore or with a
tapered bore, the taper being 1:12 as for the
basic bearings.
Special solutions for

bearings with extended
inner ring
Self-aligning ball bearings with extended
inner ring (series 11200) are used for
applications employing commercial ground
shafting. The special bore tolerance of
these bearings allows easy mounting and
dismounting.
Self-aligning ball bearings with extended
inner ring are located axially by pins or
shouldered screws which engage in a slot at
one side of the inner ring. The pins or
screws also prevent the inner ring from
turning on the shaft. When these bearings
are used in pairs, the slots of the inner rings
must either be adjacent or at the outboard
positions. Otherwise, the shaft will be
located in one direction only.
Product highlights
Optimum performance
SKF self-aligning ball bearings have
been designed to provide optimum
performance in a wide range of
machinery and equipment applications
and are particularly suitable for applications where misalignment can arise
from errors in shaft and housing alignment or shaft deflection and high
speed is a requirement.
Capacity for resistance-free,

self-alignment
In the event of minor angular misalignment, the problems which beset many
other bearing types do not occur
allowing for increased operational life,
lower friction and temperature, less
wear and noise during operation, and
reduced stress on both the cages and
lubricants.
Sealed bearingsgreased for life

SKF self-aligning ball bearings are
available with contact seals on both
sides which protect the bearing from
contaminants during handling and
operation. This allows for longer bearing service life, is environmentally
friendly, and requires no relubrication
making the bearing maintenance free.

Available in a wide range (5 to 130 mm
inside bore diameter), the basic SKF
design is available with a choice of
seals, cage materials, and extended
inner rings.
Application flexibility
Self-aligning bearings are used in high
speed applications where alignments
may be a problem and running accuracy
is required. Examples include fans and
blowers, textile equipment and general
conveyor equipment.

75

Introduction
Clearance
Special feature
Self-aligning ball bearings of series 14 as well
as some sizes of series 12 (K) and 13 (K) have
balls which protrude somewhat from the bearing; the actual values are given in the adjacent
table. This should be remembered when
designing adjacent components.
Protrusion of balls from

bearing side faces

SKF self-aligning ball bearings are produced
with Normal radial internal clearance (CN or C0
not marked on bearing) as standard. Radial
clearance selection is based on factors such as
high speed, operating temperature, shaft fits
and axial movement limitations. Bearings with
a tapered bore are normally supplied with a C3
radial internal clearance (marked on the bearing). Bearings having clearances that are
greater than (C3 or C4) or less than (C2)
Normal are available on request.
The clearance values are given in Table 1.
They are valid for unmounted bearings without
measuring load, and conform to ISO 57531981 (ABMA standard 20).
Loads
C1
Mounting bearings with

tapered bore
Bearings with a tapered bore are always
mounted with an interference fit on the shaft,
adapter sleeve or withdrawal sleeve. As a
measure of the degree of interference of the fit,
either the reduction in radial internal clearance
of the bearing or the axial displacement of the
inner ring on the tapered bearing seating can
be used.
The mounting of self-aligning ball bearings
with tapered bore calls for experience and skill
as they have a relatively small internal clearance,
and a reliable measurement of the clearance
reduction is not always possible. There are specific mounting instructions for these bearings in
the SKF Bearing Installation and Maintenance
Guide (140-710) or by visiting the SKF website
www.skf.com/mount for exact mounting
instructions.
Equivalent dynamic bearing loads

P = Fr + Y1Fa where Fa / Fr e
P = 0.65 Fr + Y2 Fa when Fa / Fr > e
Values of factors e, Y1 and Y2 for each
individual bearing are given in the bearing
Table 2, page 78.
Minimum load
Bearing
Protrusion
C1
mm
in
1224(K)
1226
1.3
1.4
0.0512
0.0551
1318(K)
1319(K)
1320(K)
1322(K)
1.0
1.5
2.5
2.6
0.0394
0.0591
0.0984
0.1024
76
In order to provide satisfactory operation of

all ball and roller bearings they must always
be subjected to a given minimum load.
This is also true of self-aligning ball bearings,
particularly if they run at high speeds where
the inertia forces of the balls and cage, and the
influence on the rolling conditions in the bearing
and may cause damaging sliding movements to
occur between the balls and the raceways.
using the Interactive Engineering catalog on the
SKF website www.skf.com or by contacting SKF
Applications Engineering. However, the weight
of the components supported by the bearing,
together with the external forces, often exceeds
the requisite minimum load. If this is not the
case, an additional radial load must be applied
to the bearing; for example, by increasing belt
tension or similar means.

Frequency vibration data is available on the SKF
website www.skf.com, in the Interactive
Introduction
Table 1
Radial internal clearance of self-aligning ball bearings
Bore
diameter
d
over incl.
mm

C2
min
m
max
min
in
max
Normal
min max
m
min
in
max
C3
min
m
max
min
in
max
C4
min
m
max
min
in
max
0.0010
Bearings with cylindrical bore

2.5
0.0000
0.0003
15
0.0002
0.0006
10
20
0.0004
0.0008
15
25
0.0006
10
0.0001
0.0004
17
0.0002
0.0007
12
25
0.0005
0.0010
19
33
0.0007
0.0013
10
14
10
0.0001
0.0004
19
0.0002
0.0007
13
26
0.0005
0.0010
21
35
0.0008
0.0014
14
18
12
0.0001
0.0005
21
0.0003
0.0008
15
28
0.0006
0.0011
23
37
0.0009
0.0015
18
24
14
0.0002
0.0006
10
23
0.0004
0.0009
17
30
0.0007
0.0012
25
39
0.0010
0.0015
24
30
16
0.0002
0.0006
11
24
0.0004
0.0009
19
35
0.0007
0.0014
29
46
0.0011
0.0018
30
40
18
0.0002
0.0007
13
29
0.0005
0.0011
23
40
0.0009
0.0016
34
53
0.0013
0.0021
40
50
19
0.0002
0.0007
14
31
0.0006
0.0012
25
44
0.0010
0.0017
37
57
0.0015
0.0022
50
65
21
0.0003
0.0008
16
36
0.0006
0.0014
30
50
0.0012
0.0020
45
69
0.0018
0.0027
65
80
24
0.0003
0.0009
18
40
0.0007
0.0016
35
60
0.0014
0.0024
54
83
0.0021
0.0033
80
100
27
0.0004
0.0011
22
48
0.0009
0.0019
42
70
0.0017
0.0028
64
96
0.0025
0.0038
100
120
10
31
0.0004
0.0012
25
56
0.0010
0.0022
50
83
0.0020
0.0033
75
114
0.0030
0.0045
120
140
10
38
0.0004
0.0015
30
68
0.0012
0.0027
60
100
0.0024
0.0039
90
135
0.0035
0.0053
0.0017
Bearings with tapered bore

18
24
17
0.0003
0.0007
13
26
0.0005
0.0010
20
33
0.0008
0.0013
28
42
0.0011
24
30
20
0.0004
0.0008
15
28
0.0006
0.0011
23
39
0.0009
0.0015
33
50
0.0013
0.0020
30
40
12
24
0.0005
0.0009
19
35
0.0007
0.0014
29
46
0.0011
0.0018
40
59
0.0016
0.0023
40
50
14
27
0.0006
0.0011
22
39
0.0009
0.0015
33
52
0.0013
0.0020
45
65
0.0018
0.0026
50
65
18
32
0.0007
0.0013
27
47
0.0011
0.0019
41
61
0.0016
0.0024
56
80
0.0022
0.0031
65
80
23
39
0.0009
0.0015
35
57
0.0014
0.0022
50
75
0.0020
0.0030
69
98
0.0027
0.0039
80
100
29
47
0.0011
0.0019
42
68
0.0017
0.0027
62
90
0.0024
0.0035
84
116
0.0033
0.0046
100
120
35
56
0.0014
0.0022
50
81
0.0020
0.0032
75
108
0.0030
0.0043
100
139
0.0039
0.0055
77
Table 2
Calculation factors for self-aligning ball bearings
Designation
Calculation factors
Bearings with
cylindrical bore
Y1
Y2
126
127
129
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1224
1226
0.33
0.33
0.33
0.33
0.33
0.33
0.31
0.30
0.28
0.25
0.23
0.22
0.21
0.21
0.19
0.19
0.18
0.18
0.17
0.16
0.17
0.17
0.17
0.17
0.17
0.17
0.19
0.19
1.9
1.9
1.9
1.9
1.9
1.9
2.0
2.1
2.2
2.5
2.7
2.9
3.0
3.0
3.3
3.3
3.5
3.5
3.7
3.9
3.7
3.7
3.7
3.7
3.7
3.7
3.3
3.3
3.0
3.0
3.0
3.0
3.0
3.0
3.1
3.3
3.5
3.9
4.2
4.5
4.6
4.6
5.1
5.1
5.4
5.4
5.7
6.1
5.7
5.7
5.7
5.7
5.7
5.7
5.1
5.1
0.33
0.35
0.31
0.30
0.28
0.28
0.25
0.25
0.28
0.23
0.24
0.23
0.23
0.22
0.22
0.22
0.22
0.22
0.22
0.23
0.23
0.22
1.9
1.8
2.0
2.1
2.2
2.2
2.5
2.5
2.2
2.7
2.6
2.7
2.7
2.9
2.9
2.9
2.9
2.9
2.9
2.7
2.7
2.9
3.0
2.8
3.1
3.3
3.5
3.5
3.9
3.9
3.5
4.2
4.1
4.2
4.2
4.5
4.5
4.5
4.5
4.5
4.5
4.2
4.2
4.5
135
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1322
78
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
K
K
K
K
K
Table 2
Calculation factors for self-aligning ball bearings
Designation
Calculation factors
Bearings with
cylindrical bore
Y1
Y2
1412
0.33
1.90
3.0
2200 E
2201 E
2202 E
2203 E
2204 E
2205 E
2206 E
2207 E
2208 E
2209 E
2210 E
2211 E
2212 E
2213 E
2214
2215
2216 E
2217
2218
2219
2220
2221
2222
0.54
0.50
0.43
0.43
0.40
0.35
0.33
0.31
0.22
0.26
0.23
0.23
0.24
0.24
0.27
0.25
0.22
0.25
0.27
0.27
0.27
0.28
0.28
1.15
1.25
1.50
1.50
1.60
1.80
1.90
2.00
2.90
2.40
2.70
2.70
2.60
2.60
2.30
2.50
2.90
2.50
2.30
2.30
2.30
2.20
2.20
1.8
2.0
2.3
2.3
2.4
2.8
3.0
3.1
4.5
3.7
4.2
4.2
4.1
4.1
3.6
3.9
4.5
3.9
3.6
3.6
3.6
3.5
3.5
2301
2302
2303
2304
2305
2306
2307 E
2308 E
2309 E
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2322
0.60
0.52
0.52
0.52
0.48
0.44
0.46
0.23
0.33
0.43
0.40
0.33
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
1.05
1.20
1.20
1.20
1.30
1.40
1.35
2.70
1.90
1.50
1.60
1.90
1.70
1.70
1.70
1.70
1.70
1.70
1.70
1.70
1.70
1.6
1.9
1.9
1.9
2.0
2.2
2.1
4.2
3.0
2.3
2.4
3.0
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
79

Double row
Open, cylindrical and tapered bore
Series: 126 1226 M
Size: 6 mm 130 mm
0.2362 in 5.1181 in
Cylindrical Bore
Tapered Bore
Tapered bore
Cylindrical bore
Designation
Outside diameter
Width
Bore
Basic load ratings

Dynamic
Static
Speed rating
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
2 510
2 650
3 900
560
600
880
480
560
820
110
130
180
70 000
63 000
60 000
0.3543
0.3937
0.4331
5 530
6 240
7 410
1 240
1 400
1 670
1 180
1 430
1 760
270
320
400
12
14
15
0.4724
0.5512
0.5906
8 840
12 700
14 300
1 990
2 850
3 210
2 200
3 400
4 000
2.4409
2.8346
3.1496
16
17
18
0.6299
0.6693
0.7087
15 600
19 000
19 900
3 510
4 270
4 470
1.7717 85
1.9685 90
2.1654 100
3.3465
3.5433
3.9370
19
20
21
0.7480
0.7874
0.8268
60
65
70
2.3622 110
2.5591 120
2.7559 125
4.3307
4.7244
4.9213
22
23
24
1215
1216
1217
75
80
85
2.9528 130
3.1496 140
3.3465 150
5.1181
5.5118
5.9055
1218
1219
1220
90
95
100
3.5433 160
3.7402 170
3.9370 180
1221
1222
1224 M
105
110
120
1226 M
130
mm
in
mm
6
7
9
0.2362
0.2756
0.3543
19
22
26
0.7480
0.8661
1.0236
6
7
8
0.2362
0.2756
0.3150
1200 E
1201 E
1202 E
10
12
15
0.3937
0.4724
0.5906
30
32
35
1.1811
1.2598
1.3780
9
10
11
1203 E
1204 E
1205 E
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
1206 E
1207 E
1208 E
30
35
40
1.1811
1.3780
1.5748
62
72
80
1209 E
1210 E
1211 E
45
50
55
1212 E
1213 E
1214
126
127
129
in
mm
C
in
C0
Mass
Designation
Tapered Adapter
bore
sleeve
kg
lb
kg
45 000
40 000
38 000
0.01
0.01
0.02
0.10
0.10
0.10
56 000
50 000
45 000
36 000
32 000
28 000
0.03
0.04
0.05
0.10
0.10
0.20
490
760
900
38 000
32 000
28 000
24 000
20 000
18 000
0.07
0.12
0.14
0.20
0.30
0.40
1204 EK
1205 EK
H 204
H 205
0.04 0.08
0.07 0.14
4 650
6 000
6 950
1 050
1 350
1 560
24 000
20 000
18 000
15 000
13 000
11 000
0.22
0.32
0.42
0.50
0.80
1.00
1206 EK
1207 EK
1208 EK
H 206
H 207
H 208
0.09 0.19
0.12 0.26
0.16 0.35
22 900
26 500
27 600
5 150 7 800
5 960 9 150
6 200 10 600
1 750
2 060
2 380
17 000
16 000
14 000
11 000
10 000
9 000
0.47
0.53
0.71
1.10
1.20
1.60
1209 EK
1210 EK
1211 EK
H 209
H 210
H 211
0.21 0.46
0.24 0.53
0.28 0.62
0.8661
0.9055
0.9449
31 200
35 100
35 800
7 010 12 200
7 890 14 000
8 050 14 600
2 740
3 150
3 280
12 000
11 000
11 000
8 500
7 000
7 000
0.90
1.15
1.25
2.00
2.60
2.80
1212 EK
1213 EK
H 212
H 213
0.31 0.68
0.36 0.79
25
26
28
0.9843
1.0236
1.1024
39 000
39 700
48 800
8 770 15 600
8 920 17 000
10 970 20 800
3 510
3 820
4 680
10 000
9 500
9 000
6 700
6 000
5 600
1.35
1.65
2.05
3.00
3.70
4.60
1215 K
1216 K
1217 K
H 215
H 216
H 217
0.66 1.45
0.81 1.80
0.94 2.05
6.2992
6.6929
7.0866
30
32
34
1.1811
1.2598
1.3386
57 200
63 700
68 900
12 860 23 600
14 320 27 000
15 490 30 000
5 310
6 070
6 740
8 500
8 000
7 500
5 300
5 000
4 800
2.50
3.10
3.70
5.60
6.90
8.20
1218 K
1219 K
1220 K
H 218
H 219
H 220
1.10 2.45
1.25 2.75
1.40 3.10
4.1339 190
4.3307 200
4.7244 215
7.4803
7.8740
8.4646
36
38
42
1.4173 74 100
1.4961 88 400
1.6535 119 000
16 660 32 500
19 870 39 000
26 750 53 000
7 310
8 770
11 910
7 000
6 700
6 300
4 500
4 300
4 000
4.35
5.15
6.75
9.60
11.40
14.90
1221 K
H 221 1.60 3.55
1222 K
H 222 1.80 3.95
1224 KM H 3024 1.80 3.95
5.1181 230
9.0551
46
1.8110 127 000
28 550 58 500
13 150
5 600
3 600
8.30
18.30
80
Mass
lb
Double row
Open, cylindrical and tapered bore
Series: 135 1322 M
Size: 5 mm 110 mm
0.1969 in 4.3307 in
Cylindrical Bore
Tapered Bore
Tapered bore
Cylindrical bore
Designation
Series: 1412 M
Size: 60 mm (2.3622 in)
Outside diameter
Width
Bore
d
Basic load ratings

Dynamic
Static
mm
in
mm
in
mm
in
135
1301 E
1302 E
5
12
15
0.1969
0.4724
0.5906
19
37
42
0.7480
1.4567
1.6535
6
12
13
0.2362
0.4724
0.5118
1303 E
1304 E
1305 E
17
20
25
0.6693
0.7874
0.9843
47
52
62
1.8504
2.0472
2.4409
14
15
17
1306 E
1307 E
1308 E
30
35
40
1.1811
1.3780
1.5748
72
80
90
2.8346
3.1496
3.5433
1309 E
1310 E
1311 E
45
50
55
1.7717 100
1.9685 110
2.1654 120
1312 E
1313 E
1314
60
65
70
1315
1316
1317
Speed rating
C0
lbf
Reference Limiting
speed
speed
r/min
r/min
lbf
2 510
9 360
10 800
560
2 100
2 430
480
2 160
2 600
110
490
580
63 000
40 000
34 000
0.5512
0.5906
0.6693
12 700
14 300
19 000
2 850
3 210
4 270
3 400
4 000
5 400
760
900
1 210
19
21
23
0.7480
0.8268
0.9055
22 500
26 500
33 800
5 060
5 960
7 600
6 800
8 500
11 200
3.9370
4.3307
4.7244
25
27
29
0.9843
1.0630
1.1417
39 000
43 600
50 700
8 770
9 800
11 400
2.3622 130
2.5591 140
2.7559 150
5.1181
5.5118
5.9055
31
33
35
1.2205
1.2992
1.3780
58 500
65 000
74 100
75
80
85
2.9528 160
3.1496 170
3.3465 180
6.2992
6.6929
7.0866
37
39
41
1.4567
1.5354
1.6142
1318
1319
1320
90
95
100
3.5433 190
3.7402 200
3.9370 215
7.4803
7.8740
8.4646
1322 M
110
4.3307 240
1412 M
60
2.3622 150
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
45 000
28 000
24 000
0.01
0.07
0.09
0.10
0.20
0.20
28 000
26 000
22 000
20 000
18 000
15 000
0.13
0.16
0.26
0.30
0.40
0.60
1304 EK
1305 EK
H 304
H 305
0.04 0.09
0.07 0.16
1 530
1 910
2 520
19 000
16 000
14 000
13 000
11 000
9 500
0.39
0.51
0.72
0.90
1.20
1.60
1306 EK
1307 EK
1308 EK
H 306
H 307
H 308
0.10 0.21
0.14 0.31
0.17 0.37
13 400
14 000
18 000
3 010
3 150
4 050
12 000
12 000
11 000
8 500
8 000
7 500
0.96
1.20
1.60
2.20
2.70
3.60
1309 EK
1310 EK
1311 EK
H 309
H 310
H 311
0.23 0.51
0.27 0.60
0.32 0.71
13 150
14 610
16 660
22 000
25 500
27 500
4 950
5 730
6 180
9 000
8 500
8 500
6 300
6 000
6 000
1.95
2.45
3.00
4.30
5.50
6.60
1312 EK
1313 EK
-
H 312
H 313
0.36 0.79
0.42 0.93
79 300
88 400
97 500
17 830
19 870
21 920
30 000
33 500
38 000
6 740
7 530
8 540
8 000
7 500
7 000
5 600
5 300
4 800
3.55
4.20
5.00
7.80
9.30
11.00
1315 K
1316 K
1317 K
H 315
H 316
H 317
0.78 1.70
0.95 2.10
1.10 2.45
43
45
47
1.6929 117 000

1.7717 133 000
1.8504 143 000
26 300
29 900
32 150
44 000 9 890
51 000 11 460
57 000 12 810
6 700
6 300
6 000
4 500
4 300
4 000
5.80
6.70
8.30
12.80
14.80
18.30
1318 K
1319 K
1320 K
H 318
H 319
H 320
1.30 2.85
1.40 3.10
1.60 3.55
9.4488
50
1.9685 163 000
36 640
72 000 16 190
5 300
3 600
12.00
26.50
1322 K
H 322
2.05 4.50
5.9055
42
1.6535 125 000
28 100
41 500
9 000
6 300
3.95
8.70
9 330
kg
lb
81

Double row
Cylindrical and tapered bore
Open and sealed
Series: 2200 E 2222
Size: 10 mm 110 mm
0.3937 in 4.3307 in
2RS1
Cylindrical Bore
Tapered Bore
Cylindrical bore
Designation
Outside diameter
Width
Bore
d
mm
D
in
mm
Basic load ratings

Dynamic
Static
B
in
mm
C
in
Speed rating
lbf
Reference Limiting
speed
speed
r/min
r/min
C0
lbf
2RS1
Tapered bore
2RS1
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
kg
2200 E
2201 E
2202 E
10
12
15
0.3937
0.4724
0.5906
30
32
35
1.1811
1.2598
1.3780
14
14
14
0.5512
0.5512
0.5512
8 060
8 520
8 710
1 810
1 920
1 960
1 730
1 900
2 040
390
430
460
50 000
45 000
38 000
34 000
30 000
26 000
0.05
0.05
0.06
0.10
0.10
0.10
2203 E
2204 E
2205 E
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
16
18
18
0.6299
0.7087
0.7087
10 600
16 800
16 800
2 380
3 780
3 780
2 550
4 150
4 400
570
930
990
34 000
28 000
26 000
24 000
20 000
18 000
0.09
0.14
0.16
0.20
0.30
0.40
2205 EK
H 305
0.07 0.16
2206 E
2207 E
2208 E
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409
2.8346
3.1496
20
23
23
0.7874
0.9055
0.9055
23 800
30 700
31 900
5 350 6 700
6 900 8 800
7 170 10 000
1 510
1 980
2 250
22 000
18 000
16 000
15 000
12 000
11 000
0.26
0.40
0.51
0.60
0.90
1.10
2206 EK
2207 EK
2208 EK
H 306
H 307
H 308
0.10 0.21
0.14 0.31
0.17 0.37
2209 E
2210 E
2211 E
45
50
55
1.7717 85
1.9685 90
2.1654 100
3.3465
3.5433
3.9370
23
23
25
0.9055
0.9055
0.9843
32 500
33 800
39 000
7 310 10 600
7 600 11 200
8 770 13 400
2 380
2 520
3 010
15 000
14 000
12 000
10 000
9 500
8 500
0.55
0.60
0.81
1.20
1.30
1.80
2209 EK
2210 EK
2211 EK
H 309
H 310
H 311
0.23 0.51
0.27 0.6
0.32 0.71
2212 E
2213 E
2214
60
65
70
2.3622 110
2.5591 120
2.7559 125
4.3307
4.7244
4.9213
28
31
31
1.1024
1.2205
1.2205
48 800
57 200
44 200
10 970 17 000
12 860 20 000
9 940 17 000
3 820
4 500
3 820
11 000
10 000
10 000
8 000
7 000
6 700
1.10
1.45
1.50
2.45
3.20
3.30
2212 EK
2213 EK
H 312
H 313
0.36 0.79
0.42 0.93
2215 E
2216 E
2217
75
80
85
2.9528 130
3.1496 140
3.3465 150
5.1181
5.5118
5.9055
31
33
36
1.2205
1.2992
1.4173
58 500
65 000
58 500
13 150 22 000
14 610 25 500
13 150 23 600
4 950
5 730
5 310
9 000
8 500
8 000
6 300
6 000
5 600
1.60
2.00
2.50
3.55
4.40
5.50
2215 K
2216 EK
2217 K
H 315
H 316
H 317
0.78 1.7
0.95 2.1
1.10 2.45
2218
2219 M
2220
90
95
100
3.5433 160
3.7402 170
3.9370 180
6.2992
6.6929
7.0866
40
43
46
1.5748
1.6929
1.8110
70 200
83 200
97 500
15 780 28 500
18 700 34 500
21 920 40 500
6 410
7 760
9 100
7 500
7 000
6 700
5 300
5 000
4 800
3.40
4.10
5.00
7.50
9.05
11.00
2218 K
H 318
2219 KM H 319
2220 K
H 320
1.30 2.85
1.40 3.1
1.60 3.55
2221 M
2222
105
110
4.1339 190
4.3307 200
7.4803
7.8740
50
53
1.9685 108 000

2.0866 124 000
24 280 45 000
27 880 52 000
10 120
11 690
6 300
6 000
4 500
4 300
6.10
7.10
13.50
15.50
2221 K
2222 K
1.85
2.05
H 321
H 322
82
lb
4.1
4.5
Double row
Open and sealed
Series: 2302 2320 M
Size: 15 mm 100 mm
0.5906 in 3.9370 in
2RS1
Cylindrical Bore
Tapered Bore
Cylindrical bore
Designation
Principal Dimensions
Outside diameter
Width
Bore
d
mm
2RS1
2RS1
Tapered bore
D
in
mm
Basic load ratings

Dynamic
Static
B
in
mm
C
in
Speed rating
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
kg
lb
2302
2303
2304
15
17
20
0.5906
0.6693
0.7874
42
47
52
1.6535
1.8504
2.0472
17
19
21
0.6693
0.7480
0.8268
11 900
14 600
18 200
2 680
3 280
4 090
2 900
3 550
4 750
650
800
1 070
32 000
30 000
26 000
24 000
22 000
19 000
0.11
0.16
0.21
0.20
0.40
0.50
2305
2306
2307 E
25
30
35
0.9843
1.1811
1.3780
62
72
80
2.4409
2.8346
3.1496
24
27
31
0.9449
1.0630
1.2205
24 200
31 200
39 700
5 440 6 550
7 010 8 800
8 920 11 200
1 470
1 980
2 520
22 000
18 000
16 000
16 000
13 000
12 000
0.34
0.50
0.68
0.70
1.10
1.50
2305 K
2306 K
2307 EK
H 2305 0.09 0.19

H 2306 0.11 0.24
H 2307 0.16 0.35
2308 E
2309 E
2310
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
33
36
40
1.2992
1.4173
1.5748
54 000
63 700
63 700
12 140 16 000
14 320 19 300
14 320 20 000
3 600
4 340
4 500
14 000
13 000
14 000
10 000
9 000
9 500
0.93
1.25
1.65
2.10
2.80
3.60
2308 EK
2309 EK
2310 K
H 2308 0.22 0.49

H 2309 0.27 0.6
H 2310 0.34 0.75
2311
2312
2313
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
43
46
48
1.6929
1.8110
1.8898
76 100
87 100
95 600
17 110 24 000
19 580 28 500
21 490 32 500
5 400
6 410
7 310
11 000
9 500
9 000
7 500
7 000
6 300
2.10
2.60
3.25
4.60
5.70
7.20
2311 K
2312 K
2313 K
H 2311 0.39 0.86

H 2312 0.45 0.99
H 2313 0.52 1.15
2314
2315
2316
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
51
55
58
2.0079 111 000

2.1654 124 000
2.2835 135 000
24 950 37 500
27 880 43 000
30 350 49 000
8 430
9 670
11 020
8 000
7 500
7 000
6 000
5 600
5 300
3.90
4.70
6.10
8.60
10.40
13.40
2315 K
2316 K
H 2315 1.10 2.45

H 2316 1.20 2.65
2317
2318 M
2319 M
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866
7.4803
7.8740
60
64
67
2.3622 140 000

2.5197 153 000
2.6378 165 000
31 470 51 000
34 390 57 000
37 090 64 000
11 460
12 810
14 390
6 700
6 300
6 000
4 800
4 500
4 500
7.05
8.45
9.80
15.50
18.60
21.60
2317 K
2318 K
2319 K
H 2317 1.35
3
H 2318 1.60 3.55
H 2319 1.80 3.95
2320 M
100
3.9370
215
8.4646
73
2.8740 190 000
42 710 80 000
17 980
5 600
4 000
12.50
27.60
2320 K
H 2320 2.00
4.4
83

Double row
Open and sealed
Series: 2200 E 2RS1KTN9 2208 E 2RS1KTN9
Size: 10 mm 40 mm
0.3937 in 1.5748 in
2RS1
Cylindrical Bore
Tapered Bore
Cylindrical bore
Designation
Outside diameter
Width
Bore
d
mm
D
in
mm
Basic load ratings

Dynamic
Static
B
in
mm
C
in
Speed rating
Sealed
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
2RS1
Tapered bore
2RS1
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
kg
lb
2200 E2RS1TN9
10
0.3937
30
1.1811
14
0.5512
5 530
1 240
1 180
270
17 000
0.05
0.10
2201 E2RS1TN9
12
0.4724
32
1.2598
14
0.5512
6 240
1 400
1 430
320
16 000
0.05
0.10
2202 E2RS1TN9
15
0.5906
35
1.3780
14
0.5512
7 410
1 670
1 760
400
14 000
0.05
0.10
2203 E2RS1TN9
17
0.6693
40
1.5748
16
0.6299
8 840
1 990
2 200
490
12 000
0.10
0.20
2204 E2RS1TN9
20
0.7874
47
1.8504
18
0.7087
12 700
2 850
3 400
760
10 000
0.14
0.30
2205 E2RS1KTN9
25
0.9843
52
2.0472
18
0.7087
14 300
3 210
4 000
900
9 000
0.16
0.40
2205 E2RS1K H 305 C 0.07 0.20
2205 E2RS1TN9
25
0.9843
52
2.0472
18
0.7087
14 300
3 210
4 000
900
9 000
0.16
0.40
2206 E2RS1KTN9
30
1.1811
62
2.4409
20
0.7874
15 600
3 510
4 650
1 050
7 500
0.26
0.60
2206 E2RS1K H 306 C 0.10 0.30
2206 E2RS1TN9
30
1.1811
62
2.4409
20
0.7874
15 600
3 510
4 650
1 050
7 500
0.26
0.60
2207 E2RS1KTN9
35
1.3780
72
2.8346
23
0.9055
19 000
4 270
6 000
1 350
6 300
0.41
0.90
2207 E2RS1K H 307 C 0.14 0.40
2207 E2RS1TN9
35
1.3780
72
2.8346
23
0.9055
19 000
4 270
6 000
1 350
6 300
0.41
0.90
2208 E2RS1KTN9
40
1.5748
80
3.1496
23
0.9055
19 900
4 470
6 950
1 560
5 600
0.50
1.10
2208 E2RS1K H 308 C 0.17 0.40
84
Double row
Open and sealed
Series: 2308 E 2RS1TN9 2308 E 2RS1TN9
Size: 15 mm 70 mm
0.5906 in 2.7559 in
2RS1
Cylindrical Bore
Tapered Bore
Cylindrical bore
Designation
Outside diameter
Width
Bore
d
mm
2RS1
2RS1
Tapered bore
D
in
mm
Basic load ratings

Dynamic
Static
B
in
mm
C
in
Speed rating
Sealed
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
kg
lb
2208 E2RS1TN9
40
1.5748
80
3.1496
23
0.9055
19 900
4 470
6 950
1 560
5 600
0.50
1.10
2209 E2RS1KTN9
45
1.7717
85
3.3465
23
0.9055
22 900
5 150
7 800
1 750
5 300
0.53
1.20
2209 E2RS1K H 309 C 0.23 0.60
2209 E2RS1TN9
45
1.7717
85
3.3465
23
0.9055
22 900
5 150
7 800
1 750
5 300
0.53
1.20
2210 E2RS1KTN9
50
1.9685
90
3.5433
23
0.9055
22 900
5 150
8 150
1 830
4 800
0.57
1.30
2210 E2RS1K H 310 C 0.27 0.60
2210 E2RS1TN9
50
1.9685
90
3.5433
23
0.9055
22 900
5 150
8 150
1 830
4 800
0.57
1.30
2211 E2RS1KTN9
55
2.1654
100
3.9370
25
0.9843
27 600
6 200 10 600
2 380
4 300
0.79
1.70
2211 E2RS1K H 311 C 0.32 0.80
2211 E2RS1TN9
55
2.1654
100
3.9370
25
0.9843
27 600
6 200 10 600
2 380
4 300
0.79
1.70
2212 E2RS1TN9
60
2.3622
110
4.3307
28
1.1024
31 200
7 010 12 200
2 740
3 800
1.05
2.30
2213 E2RS1KTN9
65
2.5591
120
4.7244
31
1.2205
35 100
7 890 14 000
3 150
3 600
1.40
3.10
2213 E2RS1K H 313 C 0.42 1.00
2213 E2RS1TN9
65
2.5591
120
4.7244
31
1.2205
35 100
7 890 14 000
3 150
3 600
1.40
3.10
2214 E2RS1TN9
70
2.7559
125
4.9213
31
1.2205
35 800
8 050 14 600
3 280
3 400
1.45
3.20
2302 E2RS1TN9
15
0.5906
42
1.6535
17
0.6693
10 800
2 430
580
12 000
0.11
0.20
2 600
85

Double row
Open and sealed
Series: 2200 E 2200 E 2RS1KTN9
Size: 17 mm 50 mm
0.6693 in 1.9685 in
2RS1
Cylindrical Bore
Tapered Bore
Cylindrical
bore
Designation
Outside diameter
Width
Bore
d
mm
D
in
mm
Basic load ratings

Dynamic
Static
B
in
mm
C
in
Speed rating
Sealed
C0
lbf
lbf
2RS1
Tapered bore
Reference Limiting
speed
speed
r/min
r/min
2RS1
Mass
Designation
Mass
Tapered Adapter
bore
sleeve
kg
lb
kg
lb
2303 E2RS1TN9
17
0.6693
47
1.8504
19
0.7480
12 700
2 850
3 400
760
11 000
0.16
0.40
2304 E2RS1TN9
20
0.7874
52
2.0472
21
0.8268
14 300
3 210
4 000
900
9 000
0.21
0.50
2305 E2RS1TN9
25
0.9843
62
2.4409
24
0.9449
19 000
4 270
5 400
1 210
7 500
0.34
0.70
2306 E2RS1TN9
30
1.1811
72
2.8346
27
1.0630
22 500
5 060
6 800
1 530
6 700
0.51
1.10
2307 E2RS1TN9
35
1.3780
80
3.1496
31
1.2205
26 500
5 960
8 500
1 910
5 600
0.70
1.50
2308 E2RS1TN9
40
1.5748
90
3.5433
33
1.2992
33 800
7 600 11 200
2 520
5 600
0.96
2.10
2309 E2RS1TN9
45
1.7717 100
3.9370
36
1.4173
39 000
8 770 13 400
3 010
4 500
1.30
2.90
2310 E2RS1TN9
50
1.9685 110
4.3307
40
1.4173
43 600
9 800 14 000
3 150
4 000
1.65
3.60
86
Thrust bearings
53210
Nomenclature
Thrust ball bearing
Spherical roller thrust bearing
U210
M
29430 E
1
1
with seating washer
1. Features
1. Features
Machined brass cage, roller guided
Optimized internal design,

window-type steel cage
J9
Internal design change to J cage
Machined brass cage (no symbol)
Machined steel or special cast iron cage,

roller guided
EF

machined steel cage
Dimensional and running accuracy to ISO

tolerance class 5 (approximately ABEC 5)
EM

machined brass cage
RD
Spacer sleeve
P5
89
Thrust bearings
Product
Details
Technical
features
Thrust ball bearing
Spherical roller thrust bearing
Boundary
dimensions
Bearings with flat housing washers

are in accordance with ISO 104-2002.
The bearings with sphered housing
washers have dimensions in accordance
with DIN 711:1988 and DIN 715:1987.
Tolerances
ABEC 1
RBEC 1
Heat stabilization
250 F (125 C)
392 F (200 C)
Misalignment
None contact SKF
normal load conditions

Fa + 2.7 x Fr 0.05 C0
series 29200 - 2 degrees

series 29300 - 2.5 degrees
series 29400 - 3 degrees
heavy load conditions
Fa + 2.7 x Fr > 0.05 C0
1.5 degrees for all series

Cage materials
Standard
Pressed steel
Steel
Optional
Machined brass (M)
Machined brass (larger bearings only)
Axial load max
Thrust bearing
(see tables in General Catalog - 6000 EN)
Thrust bearing
(see tables in General Catalog - 6000 EN)
Seals
Not available
Not available
Single direction
thrust ball bearing
90
Double direction
thrust ball bearing
Spherical roller
thrust bearing
Introduction
Introduction
SKF produces two types of thrust
bearingsball and rollerboth of the separable
design. The thrust ball bearings are manufactured in single direction and double direction
designs and are specifically designed into
applications in which there is no radial load.
The spherical roller thrust bearings are capable of handling shaft misalignment, very heavy
axial loads, small radial loads and relatively
high speeds.
Basic design
Single direction thrust ball bearings
Thrust ball bearings of this type are suitable for
the accommodation of axial loads in one direction only and can locate a shaft in one direction; they may not, however, be subjected to
any radial load.
Single direction thrust ball bearings comprise
a shaft washer with raceway groove, a ball and
cage thrust assembly and a housing washer
with raceway groove. The housing washer can
have a flat or sphered seating surface as
required. Bearings with a sphered housing
washer can compensate for initial misalignment
if they are used together with a seating washer
which has a correspondingly sphered surface.
The sphered seating washer must be ordered
separately. See Table 1 for designations and
dimensions.
The bearings are separable and mounting is
simple as the components can be mounted
individually.
Double direction thrust ball bearings

Thrust ball bearings of this type can accommodate axial loads acting in both directions and
consequently can be used to locate a shaft in
both directions. They should not be subjected
to any radial load.
Double direction thrust ball bearings
comprise one shaft washer with a raceway
groove in each face, two ball and cage thrust
assemblies and two housing washers with
raceway groove. The housing washers can have
a flat or sphered seating surface as required.
Bearings with sphered housing washers can
compensate for initial misalignments if they are
used together with seating washers which have
a correspondingly sphered surface. The
sphered seating washers must be ordered
separately. See bearing tables for designations.
The bearings are separable. The housing
washers and ball and cage thrust assemblies
are the same as those of the corresponding
single direction bearings.
Spherical roller thrust bearings

In spherical roller thrust bearings the load is
transmitted from one raceway to the other at
an angle to the bearing axis (Figure 1). They
are therefore suitable, in contrast to the other
thrust bearings shown in this catalog, for the
accommodation of radial loads in addition to
simultaneously acting axial loads. Another
important characteristic of spherical roller
thrust bearings is their self-aligning capability.
This makes the bearings insensitive to shaft
deflection and to errors of alignment of the
shaft relative to the housing.
Spherical roller thrust bearings are of separable design; the shaft washer with roller and
cage assembly, and the housing washer, can be
mounted individually.
Product highlights
Thrust ball
Purely for thrust loads
SKF thrust ball bearings are designed
for purely thrust loads and are used in
applications in which there is no radial
load. These bearings are separable to
facilitate easy mounting.
High speed capabilities

SKF thrust ball bearings offer higher
speed capabilities than the spherical
roller thrust bearings.

Single and double direction designs are
available also with sphered seating
washers to compensate for alignment
errors. Size range includes 10 to
800 mm inside diameter.
Spherical roller thrust

Accommodates heavy combined
load at high speeds
Spherical roller thrust bearings are
used extensively in applications where
heavy axial and simultaneous radial
loads need to be supported. These
heavy loads are often accompanied by
relatively high speeds.
Unaffected by misalignment
Spherical roller thrust bearings are also
insensitive to misalignments allowing
for equipment machining error without
reduced service life.
Figure 1
Used in a wide range of machinery

including gearboxes, water turbines,
steering propellers and propeller thrust
blocks, wind power stations, electric
motors, pumps, fans, crushers,
machine tools, rolling mills, extrusion
machines refiners, injection molding
machines, hydraulic motors, cranes and
tunneling.
91
Thrust bearings
Introduction
SKF spherical roller thrust bearings incorporate

a large number of asymmetrical rollers and
have specially designed raceways with an optimum conformity. They are therefore suitable for
very heavy axial loads and also permit relatively
high speed operation.
SKF spherical roller thrust bearings are manufactured in two designs depending on size and
series. Bearings identified by the designation
suffix E up to and including size 68 except
bearing 29238 E have a pressed steel
window-type cage which forms a non-separable
assembly with the rollers and the shaft washer.
All other bearings have a machined cage of
brass which is guided by a sleeve fixed in the
shaft washer bore. Here again, the shaft washer, cage and rollers form a non-separable unit.
The E design bearings represent a new generation of SKF spherical roller thrust bearings.
They have the same boundary dimensions, but
because of improvements to the internal design,
their load carrying capacity is much higher and
their friction much lower than that of the earlier
bearings.
If bearings of earlier design with a machined
cage, where axial forces were transmitted via
the cage-guiding sleeve, are to be replaced by
E design bearings with a pressed steel cage, it is
necessary to insert a spacer sleeve between the
shaft washer and the existing abutment (Figure
2). If bearings of the earlier B design are to be
replaced, the spacer sleeve used with the
B design generally needs machining (Figure 3).
The sleeves must be hardened and should have
ground faces. These sleeves may be purchased
through SKF using the designation RD + the
basic part number, i.e. RD 29434 B. Appropriate
outside diameters for the sleeves and detailed
drawings can be obtained from SKF Applications
Engineering.
Minimum load spherical roller thrust
Loads
Minimum load thrust ball
In order to provide satisfactory operation, thrust
ball bearings, like all ball and roller bearings,
must always be subjected to a given minimum
load, particularly if they are to operate at high
speeds or are subjected to high accelerations or
rapid changes in the direction of load. Under
such conditions the inertia forces of the balls
and cage(s), and the friction in the lubricant, can
have a detrimental influence on the rolling conditions in the bearing arrangement and may
cause damaging sliding movements to occur
between the balls and raceways.
The requisite minimum axial load to be
applied to thrust ball bearings can be
estimated using
Fam = A
n
1 000
where
Fam = minimum axial load, N
A
= minimum load factor,
(see product tables)
n
= rotational speed, r/min
When starting up at low temperatures or when
the lubricant is highly viscous, even greater
minimum loads may be required. The weight of
the components supported by the bearing, particularly when the shaft is vertical, together with
external forces, generally exceeds the requisite
minimum load. If this is not the case, the thrust
ball bearing must be preloaded, e.g. by springs.
Figure 2
92
In order to provide satisfactory operation,

spherical roller thrust bearings, like all ball and
roller bearings, must always be subjected to a
given minimum load, particularly if they are to
operate at high speeds or are subjected to high
accelerations or rapid changes in the direction
of the load. Under such conditions, the inertia
forces of the rollers and cage, and the friction
in the lubricant, can have a detrimental influence on the rolling conditions in the bearing
arrangement and may cause damaging sliding
movements to occur between the rollers and
raceways.
The requisite minimum axial load to be
applied to spherical roller thrust bearings can be
estimated using
Fam = 1.8 Fr + A
n
1 000
where
Fam = minimum axial load, N
Fr = radial component of load for bearings
subjected to combined load, N
C0 = basic static load rating, N
A
= minimum load factor,
n
= rotational speed, r/min
If 1.8 Fr < 0.0005 C0 then 0.0005 C0 should
be used in the above equation instead of 1.8 Fr.
At speeds higher than the reference speed or
when starting up at low temperatures, or when
the lubricant is highly viscous, even greater
minimum loads may be required. The weight
of the components supported by the bearing,
together with external forces, generally exceeds
case, the spherical roller thrust bearing must
be preloaded, e.g. by springs. For additional
information, contact the SKF Application
Engineering service.
Figure 3
Introduction
Equivalent dynamic bearing load

thrust ball
Design of associated
components for roller
thrust bearings
For single and double direction thrust ball

bearings
P = Fa

spherical roller thrust
For spherical roller thrust bearings, provided
Fr 0.55 Fa
P = Fa + 1.2 Fr
If, however, the bearing is arranged so that it
can compensate for axial and radial runouts by
relative movements between the washers and
provided
Fr 0.55 Fa then
P = 0.88 (Fa + 1.2 Fr)
For E design bearings with pressed steel cage it

is recommended that the housing bore be
relieved to prevent the cage from rubbing
against the housing if the shaft should be misaligned (Figure 4). Recommended guideline
values for the diameter of this relief are D +
15 mm for bearings with outside diameters up
to and including 380 mm and D + 20 mm for
larger bearings. Contact SKF Applications
Engineering for additional information.

SKF Explorer class

bearings
High performance SKF Explorer spherical roller
thrust bearings are shown in blue in the product tables. SKF Explorer bearings retain the
designation of the earlier standard bearings,
e.g. 29330 E. However, each bearing and its
box are marked with the name SKF Explorer.
Additional details on the Explorer performance
class bearings can be found on page 23.
can be used.
If Fr > 0.55 Fa please contact SKF
Figure 4
D
93
Thrust bearings
d
H1
H1
D3
D3
Table 1
Ball thrust bearing seating washer dimensions
94
Designation
Dimensions - seating washer
Seating
washer
D2
Bearing
Mass
D3
mm
in
mm
in
mm
R
in
mm
H1
in
mm
Seating washer
in
kg
lb
U 201
53201
20
0.7874
30
1.1811
3.5
0.1378
25
0.9843
13
0.5118
0.01
0.03
U 202
53202
24
0.9449
35
1.3780
0.1575
28
1.1024
15
0.5906
0.01
0.03
U 203
53203
26
1.0236
38
1.4961
0.1575
32
1.2598
15
0.5906
0.02
0.03
U 204
53204
30
1.1811
42
1.6535
0.1969
36
1.4173
17
0.6693
0.02
0.04
U 205
53205
36
1.4173
50
1.9685
5.5
0.2165
40
1.5748
19
0.7480
0.03
0.07
U 206
53206
42
1.6535
55
2.1654
5.5
0.2165
45
1.7717
20
0.7874
0.04
0.08
U 207
53207
48
1.8898
65
2.5591
0.2756
50
1.9685
22
0.8661
0.06
0.13
U 207
54207
48
1.8898
65
2.5591
0.2756
50
1.9685
42
1.6535
0.06
0.13
U 208
53208
55
2.1654
72
2.8346
0.2756
56
2.2047
23
0.9055
0.07
0.15
U 208
54208
55
2.1654
72
2.8346
0.2756
56
2.2047
44
1.7323
0.07
0.15
U 209
53209
60
2.3622
78
3.0709
7.5
0.2953
56
2.2047
24
0.9449
0.09
0.19
U 210
53210
62
2.4409
82
3.2283
7.5
0.2953
64
2.5197
26
1.0236
0.10
0.22
U 211
53211
72
2.8346
95
3.7402
0.3543
72
2.8346
30
1.1811
0.15
0.33
U 211
54211
72
2.8346
95
3.7402
0.3543
72
2.8346
55
2.1654
0.15
0.33
U 212
53212
78
3.0709
100
3.9370
0.3543
72
2.8346
31
1.2205
0.16
0.35
U 213
53213
82
3.2283
105
4.1339
0.3543
80
3.1496
32
1.2598
0.18
0.40
U 214
53214
88
3.4646
110
4.3307
0.3543
80
3.1496
32
1.2598
0.19
0.42
U 215
53215
92
3.6220
115
4.5276
9.5
0.3740
90
3.5433
32
1.2598
0.21
0.46
U 216
53216
98
3.8583
120
4.7244
10
0.3937
90
3.5433
33
1.2992
0.22
0.48
U 217
53217
105
4.1339
130
5.1181
11
0.4331
100
3.9370
37
1.4567
0.29
0.64
U 218
53218
110
4.3307
140
5.5118
13.5
0.5315
100
3.9370
42
1.6535
0.42
0.92
U 220
53220
125
4.9213
155
6.1024
14
0.5512
112
4.4094
45
1.7717
0.50
1.10
U 222
53222
135
5.3150
165
6.4961
14
0.5512
125
4.9213
45
1.7717
0.56
1.23
U 224
53224
145
5.7087
175
6.8898
15
0.5906
125
4.9213
46
1.8110
0.65
1.43
U 226
53226
160
6.2992
195
7.6772
17
0.6693
140
5.5118
53
2.0866
0.90
1.98
U 228
53228
170
6.6929
210
8.2677
17
0.6693
160
6.2992
55
2.1654
1.20
2.64
U 306
53306
45
1.7717
62
2.4409
0.2756
50
1.9685
25
0.9843
0.06
0.12
U 306
54306
45
1.7717
62
2.4409
0.2756
50
1.9685
46
1.8110
0.06
0.12
U 307
53307
52
2.0472
72
2.8346
7.5
0.2953
56
2.2047
28
1.1024
0.08
0.18
U 307
54307
52
2.0472
72
2.8346
7.5
0.2953
56
2.2047
52
2.0472
0.08
0.18
U 308
53308
60
2.3622
82
3.2283
8.5
0.3346
64
2.5197
31
1.2205
0.12
0.26
U 308
54308
60
2.3622
82
3.2283
8.5
0.3346
64
2.5197
59
2.3228
0.12
0.26
d
H1
H1
D3
D3
Table 1
Ball thrust bearing seating washer dimensions
Designation
Dimensions - seating washer
Seating
washer
D2
Bearing
Mass
D3
H1
Seating washer
mm
in
mm
in
mm
in
mm
in
mm
in
kg
lb
0.37
U 309
53309
65
2.5591
90
3.5433
10
0.3937
64
2.5197
33
1.2992
0.17
U 309
54309
65
2.5591
90
3.5433
10
0.3937
64
2.5197
62
2.4409
0.17
0.37
U 310
53310
72
2.8346
100
3.9370
11
0.4331
72
2.8346
37
1.4567
0.23
0.51
U 310
54310
72
2.8346
100
3.9370
11
0.4331
72
2.8346
70
2.7559
0.23
0.51
U 311
53311
80
3.1496
110
4.3307
11.5
0.4528
80
3.1496
42
1.6535
0.28
0.62
U 312
53312
85
3.3465
115
4.5276
11.5
0.4528
90
3.5433
42
1.6535
0.31
0.68
U 312
54312
85
3.3465
115
4.5276
11.5
0.4528
90
3.5433
78
3.0709
0.31
0.68
U 313
53313
90
3.5433
120
4.7244
12.5
0.4921
90
3.5433
43
1.6929
0.34
0.75
U 314
53314
98
3.8583
130
5.1181
13
0.5118
100
3.9370
48
1.8898
0.41
0.90
U 315
53315
105
4.1339
140
5.5118
15
0.5906
100
3.9370
52
2.0472
0.55
1.21
U 316
53316
110
4.3307
145
5.7087
15
0.5906
112
4.4094
52
2.0472
0.57
1.25
U 316
54316
110
4.3307
145
5.7087
15
0.5906
112
4.4094
95
3.7402
0.57
1.25
U 317
53317
115
4.5276
155
6.1024
17.5
0.6890
112
4.4094
58
2.2835
0.81
1.78
U 317
54317
115
4.5276
155
6.1024
17.5
0.6890
112
4.4094
105
4.1339
0.81
1.78
U 318
53318
120
4.7244
160
6.2992
18
0.7087
112
4.4094
59
2.3228
0.84
1.85
U 320
53320
135
5.3150
175
6.8898
18
0.7087
125
4.9213
64
2.5197
0.95
2.09
U 322
53322
150
5.9055
195
7.6772
20.5
0.8071
140
5.5118
72
2.8346
1.30
2.86
U 324
53324
165
6.4961
220
8.6614
22
0.8661
160
6.2992
80
3.1496
2.00
4.40
U 408
53408
65
2.5591
95
3.7402
12
0.4724
72
2.8346
42
1.6535
0.25
0.55
U 409
53409
72
2.8346
105
4.1339
12.5
0.4921
80
3.1496
46
1.8110
0.32
0.70
U 409
54409
72
2.8346
105
4.1339
12.5
0.4921
80
3.1496
86
3.3858
0.32
0.70
U 410
53410
80
3.1496
115
4.5276
14
0.5512
90
3.5433
50
1.9685
0.41
0.90
U 410
54410
80
3.1496
115
4.5276
14
0.5512
90
3.5433
92
3.6220
0.41
0.90
U 412
53412
95
3.7402
135
5.3150
16
0.6299
100
3.9370
58
2.2835
0.71
1.56
U 414
53414
110
4.3307
155
6.1024
19.5
0.7677
112
4.4094
69
2.7165
1.00
2.20
U 415
53415
115
4.5276
165
6.4961
21
0.8268
125
4.9213
75
2.9528
1.25
2.75
U 416
53416
125
4.9213
175
6.8898
22
0.8661
125
4.9213
78
3.0709
1.40
3.08
U 416
54416
125
4.9213
175
6.8898
22
0.8661
125
4.9213
140
5.5118
1.40
3.08
U 418
53418
140
5.5118
195
7.6772
25.5
1.0039
140
5.5118
88
3.4646
1.90
4.18
U 420
53420
155
6.1024
220
8.6614
27
1.0630
160
6.2992
98
3.8583
2.90
6.38
U 420
54420
155
6.1024
220
8.6614
27
1.0630
160
6.2992
176
6.9291
2.90
6.38
95
Thrust bearings
Thrust ball bearings
Single direction
Standard
Series: 51100 51140 M
Size: 10 mm 200 mm
0.3937 in 7.8740 in
Single direction
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Reference Limiting
speed
speed
r/min
r/min
Static
C0
lbf
lbf
Speed rating
Mass
mm
in
51100
51101
51102
10
12
15
0.3937
0.4724
0.5906
24
26
28
0.9449
1.0236
1.1024
9
9
9
0.3543
0.3543
0.3543
9 950
10 400
9 360
2 240
2 340
2 110
15 300
16 600
15 300
3 440
3 740
3 440
1.2
1.4
1.2
9 500
9 000
8 500
13 000
13 000
12 000
0.02
0.02
0.02
0.10
0.10
0.10
51103
51104
51105
17
20
25
0.6693
0.7874
0.9843
30
35
42
1.1811
1.3780
1.6535
9
10
11
0.3543
0.3937
0.4331
9 750
13 500
15 900
2 200
3 040
3 580
16 600
25 000
31 500
3 740
5 620
7 090
1.4
3.3
3.3
8 500
7 500
6 300
12 000
10 000
9 000
0.03
0.04
0.06
0.10
0.10
0.20
51106
51107
51108
30
35
40
1.1811
1.3780
1.5748
47
52
60
1.8504
2.0472
2.3622
11
12
13
0.4331
0.4724
0.5118
16 800
17 400
23 400
3 780
3 920
5 270
36 000
40 500
55 000
8 100
9 110
12 370
6.7
8.6
15
6 000
5 600
5 000
8 500
7 500
7 000
0.06
0.08
0.12
0.20
0.20
0.30
51109
51110
51111
45
50
55
1.7717
1.9685
2.1654
65
70
78
2.5591
2.7559
3.0709
14
14
16
0.5512
0.5512
0.6299
24 200
25 500
30 700
5 450
5 740
6 910
61 000
68 000
85 000
13 720
15 290
19 110
19
24
39
4 500
4 300
3 800
6 300
6 300
5 300
0.14
0.16
0.23
0.40
0.40
0.60
51112
51113
51114
60
65
70
2.3622
2.5591
2.7559
85
90
95
3.3465
3.5433
3.7402
17
18
18
0.6693
0.7087
0.7087
36 400
37 100
37 700
8 190
8 350
8 480
102 000
108 000
112 000
22 930
24 280
25 180
54
60
68
3 600
3 400
3 400
5 000
4 800
4 500
0.20
0.33
0.35
0.50
0.80
0.80
51115
51116
51117
75
80
85
2.9528
3.1496
3.3465
100
105
110
3.9370
4.1339
4.3307
19
19
19
0.7480
0.7480
0.7480
44 200
44 900
46 200
9 940
10 100
10 390
146 000
153 000
163 000
32 830
34 400
36 650
110
120
140
3 200
3 000
3 000
4 300
4 300
4 300
0.40
0.42
0.44
0.90
1.00
1.00
51118
51120
51122
90
100
110
3.5433
3.9370
4.3307
120
135
145
4.7244
5.3150
5.7087
22
25
25
0.8661
0.9843
0.9843
59 200
85 200
87 100
13 310
19 160
19 590
208 000
290 000
315 000
46 760
65 200
70 820
220
440
520
2 600
2 400
2 200
3 800
3 200
3 200
0.67
0.97
1.05
1.50
2.20
2.40
51124
51126
51128
120
130
140
4.7244
5.1181
5.5118
155
170
180
6.1024
6.6929
7.0866
25
30
31
0.9843
1.1811
1.2205
88 400
111 000
111 000
19 880
24 960
24 960
335 000
425 000
440 000
75 310
95 540
98 920
580
940
1 000
2 200
1 900
1 800
3 000
2 600
2 600
1.15
1.85
2.05
2.60
4.10
4.60
51130 M
51132 M
51134 M
150
160
170
5.9055
6.2992
6.6929
190
200
215
7.4803
7.8740
8.4646
31
31
34
1.2205
1.2205
1.3386
111 000
112 000
133 000
24 960
25 180
29 900
440 000
465 000
540 000
98 920
104 540
121 400
1 000
1 100
1 500
1 700
1 700
1 600
2 400
2 400
2 200
2.20
2.35
3.30
4.90
5.20
7.30
51136 M
51138 M
51140 M
180
190
200
7.0866
7.4803
7.8740
225
240
250
8.8583
9.4488
9.8425
34
37
37
1.3386
1.4567
1.4567
135 000
172 000
168 000
30 350
38 670
37 770
570 000
710 000
710 000
128 140
159 610
159 610
1 700
2 600
2 600
1 500
1 400
1 400
2 200
2 000
1 900
3.50
4.05
4.25
7.80
9.00
9.40
Note: For complete dimensional information, refer to the SKF Interactive Engineering Catalog on www.skfusa.com.
96
kg
lb

Single direction
Standard
Series: 51144 M 511/670 F
Size: 220 mm 670 mm
8.6614 in 26.3780 in
Single direction
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
D
mm
in
Height
H
Dynamic
C
mm
in
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
lb
51144 M
51148 M
51152 M
220
240
260
8.6614
9.4488
10.2362
270
300
320
10.6299
11.8110
12.5984
37
45
45
1.4567
1.7717
1.7717
178 000
234 000
238 000
40 020
52 610
53 510
800 000
1 040 000
1 100 000
179 840
233 800
247 280
3 300
5 600
6 300
1 300
1 100
1 100
1 900
1 600
1 500
4.60
7.55
8.10
10.20
16.70
17.90
51156 M
51160 M
51164 M
280
300
320
11.0236
11.8110
12.5984
350
380
400
13.7795
14.9606
15.7480
53
62
63
2.0866
2.4409
2.4803
319 000
364 000
371 000
71 720
81 830
83 410
1 460 000
1 760 000
1 860 000
328 210
395 650
418 130
11 000
16 000
18 000
950
800
800
1 300
1 100
1 100
12.00
17.50
19.00
26.50
38.60
41.90
51168 F
51172 F
51176 F
340
360
380
13.3858
14.1732
14.9606
420
440
460
16.5354
17.3228
18.1102
64
65
65
2.5197
2.5591
2.5591
377 000
390 000
397 000
84 750
87 680
89 250
1 960 000
2 080 000
2 200 000
440 610
467 590
494 560
20 000
22 000
25 000
750
750
750
1 100
1 000
1 000
20.50
22.00
23.00
45.20
48.60
50.80
51180 F
51184 F
51188 F
400
420
440
15.7480
16.5354
17.3228
480
500
540
18.8976
19.6850
21.2598
65
65
80
2.5591
2.5591
3.1496
403 000
410 000
527 000
90 600
92 170
118 470
2 280 000
2 400 000
3 250 000
512 550
539 520
730 600
27 000
30 000
55 000
700
700
600
1 000
1 000
850
24.00
25.50
42.00
53.00
56.30
92.60
51192 F
51196 F
511/500 F
460
480
500
18.1102
18.8976
19.6850
560
580
600
22.0472
22.8346
23.6220
80
80
80
3.1496
3.1496
3.1496
527 000
540 000
553 000
118 470
121 400
124 320
3 250 000
3 550 000
3 600 000
730 600
798 040
809 280
55 000
66 000
67 000
600
560
560
800
800
800
43.50 96.00
45.50 100.40
47.00 103.70
511/530 F
511/560 F
511/600 F
530
560
600
20.8661
22.0472
23.6220
640
670
710
25.1969
26.3780
27.9528
85
85
85
3.3465
3.3465
3.3465
650 000
650 000
663 000
146 120
146 120
149 050
4 400 000
989 120 100 000
4 650 000 1 045 320 110 000
4 800 000 1 079 040 120 000
530
500
500
750
700
700
58.50 129.00
61.00 134.50
65.00 143.30
511/630 F
511/670 F
630
670
24.8031
26.3780
750
800
29.5276
31.4961
95
105
3.7402
4.1339
728 000
852 000
163 660
191 530
5 400 000 1 213 920 150 000

6 700 000 1 506 160 230 000
450
400
630
560
84.00 185.20
105.00 231.50
97
Thrust bearings
Single direction
Standard
Series: 51200 51240 M
Size: 10 mm 200 mm
0.3937 in 7.8740 in
Single direction
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed
speed
r/min
r/min
mm
in
51200
51201
51202
10
12
15
0.3937
0.4724
0.5906
26
28
32
1.0236
1.1024
1.2598
11
11
12
0.4331
0.4331
0.4724
12 700
13 300
16 500
2 860
2 990
3 710
18 600
20 800
27 000
4 190
4 680
6 070
2
2
4
8 000
8 000
7 000
51203
51204
51205
17
20
25
0.6693
0.7874
0.9843
35
40
47
1.3780
1.5748
1.8504
12
14
15
0.4724
0.5512
0.5906
17 200
22 500
27 600
3 870
5 060
6 210
30 000
40 500
55 000
6 750
9 110
12 370
5
9
15
51206
51207
51208
30
35
40
1.1811
1.3780
1.5748
52
62
68
2.0472
2.4409
2.6772
16
18
19
0.6299
0.7087
0.7480
25 500
35 100
46 800
5 740
7 900
10 530
51 000
73 500
106 000
11 470
16 530
23 830
51209
51210
51211
45
50
55
1.7717
1.9685
2.1654
73
78
90
2.8740
3.0709
3.5433
20
22
25
0.7874
0.8661
0.9843
39 000
49 400
61 800
8 770
11 110
13 900
86 500
116 000
146 000
51212
51213
51214
60
65
70
2.3622
2.5591
2.7559
95
100
105
3.7402
3.9370
4.1339
26
27
27
1.0236
1.0630
1.0630
62 400
63 700
65 000
14 030
14 320
14 620
51215
51216
51217
75
80
85
2.9528
3.1496
3.3465
110
115
125
4.3307
4.5276
4.9213
27
28
31
1.0630
1.1024
1.2205
67 600
76 100
97 500
51218
51220
51222
90
100
110
3.5433
3.9370
4.3307
135
150
160
5.3150
5.9055
6.2992
35
38
38
1.3780
1.4961
1.4961
51224
51226
51228
120
130
140
4.7244
5.1181
5.5118
170
190
200
6.6929
7.4803
7.8740
39
45
46
51230 M
51232 M
51234 M
150
160
170
5.9055
6.2992
6.6929
215
225
240
8.4646
8.8583
9.4488
51236 M
51238 M
51240 M
180
190
200
7.0866
7.4803
7.8740
250
270
280
9.8425
10.6299
11.0236
kg
lb
11 000
11 000
10 000
0.03
0.03
0.05
0.10
0.10
0.20
6 700
6 000
5 300
9 500
8 000
7 500
0.05
0.08
0.11
0.20
0.20
0.30
13
28
58
4 800
4 000
3 800
6 700
5 600
5 300
0.13
0.22
0.28
0.30
0.50
0.70
19 450
26 080
32 830
38
69
110
3 600
3 400
2 800
5 000
4 500
4 000
0.30
0.37
0.59
0.70
0.90
1.40
150 000
163 000
173 000
33 720
36 650
38 900
120
140
160
2 800
2 600
2 600
3 800
3 600
3 600
0.65
0.78
0.79
1.50
1.80
1.80
15 200
17 110
21 920
183 000
208 000
275 000
41 140
46 760
61 820
170
220
390
2 400
2 400
2 200
3 400
3 400
3 000
0.83
0.91
1.20
1.90
2.10
2.70
119 000
124 000
130 000
26 760
27 880
29 230
325 000
345 000
390 000
73 060
77 560
87 680
550
620
790
2 000
1 800
1 700
2 800
2 400
2 400
1.70
2.20
2.40
3.80
4.90
5.30
1.5354
1.7717
1.8110
140 000
186 000
190 000
31 480
41 820
42 720
440 000
585 000
620 000
98 920
131 510
139 380
1 000
1 800
2 000
1 600
1 400
1 400
2 200
2 000
1 900
2.65
4.00
4.35
5.90
8.90
9.60
50
51
55
1.9685
2.0079
2.1654
238 000
242 000
286 000
53 510
54 410
64 300
800 000
850 000
1 020 000
179 840
191 080
229 300
3 300
3 800
5 400
1 300
1 200
1 100
1 800
1 700
1 800
6.10
6.55
8.15
13.50
14.50
18.00
56
62
62
2.2047
2.4409
2.4409
296 000
332 000
338 000
66 550
74 640
75 990
1 080 000
1 270 000
1 320 000
242 790
285 500
296 740
6 100
8 400
9 100
1 100
1 000
1 000
1 500
1 400
1 400
8.60
12.00
12.00
19.00
26.50
26.50
98
Mass

Single direction
Standard
Series: 51244 M 51276 F
Size: 220 mm 380 mm
8.6614 in 14.9606 in
Single direction
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed speed
r/min r/min
Mass
kg
lb
51244 M
51248 M
51252 M
220
240
260
8.6614
9.4488
10.2362
300
340
360
11.8110
13.3858
14.1732
63
78
79
2.4803
3.0709
3.1102
351 000
462 000
475 000
78 910
103 860
106 780
1 460 000
2 000 000
2 160 000
328 210
449 600
485 570
11 000
21 000
24 000
950
800
750
1 300
1 100
1 100
13.00
23.00
25.00
28.70
50.80
55.20
51256 M
51260 M
51264 F
280
300
320
11.0236
11.8110
12.5984
380
420
440
14.9606
16.5354
17.3228
80
95
95
3.1496
3.7402
3.7402
494 000
605 000
572 000
111 060
136 010
128 590
2 320 000
3 000 000
3 000 000
521 540
674 400
674 400
28 000
47 000
47 000
750
600
600
1 000
850
800
26.50
42.00
45.50
58.50
92.60
100.40
51268 F
51272 F
51276 F
340
360
380
13.3858
14.1732
14.9606
460
500
520
18.1102
19.6850
20.4724
96
110
112
3.7795
4.3307
4.4094
605 000
741 000
728 000
136 010
166 580
163 660
3 200 000
4 150 000
4 150 000
719 360
932 920
932 920
53 000
90 000
90 000
530
500
500
750
700
700
48.50
70.00
73.00
107.00
154.40
161.00
99
Thrust bearings
Single direction
Standard
Series: 51305 51340 M
Size: 25 mm 200 mm
0.9843 in 7.8740 in
Single direction
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed
speed
r/min
r/min
mm
in
51305
51306
51307
25
30
35
0.9843
1.1811
1.3780
52
60
68
2.0472
2.3622
2.6772
18
21
24
0.7087
0.8268
0.9449
34 500
37 700
49 400
7 760
8 480
11 110
60 000
71 000
96 500
13 490
15 970
21 700
18
26
48
4 500
3 800
3 400
51308
51309
51310
40
45
50
1.5748
1.7717
1.9685
78
85
95
3.0709
3.3465
3.7402
26
28
31
1.0236
1.1024
1.2205
61 800
76 100
88 400
13 900
17 110
19 880
122 000
153 000
190 000
27 430
34 400
42 720
77
120
190
51311
51312
51313
55
60
65
2.1654
2.3622
2.5591
105
110
115
4.1339
4.3307
4.5276
35
35
36
1.3780
1.3780
1.4173
104 000
101 000
106 000
23 380
22 710
23 830
224 000
224 000
240 000
50 360
50 360
53 960
51314
51315
51316
70
75
80
2.7559
2.9528
3.1496
125
135
140
4.9213
5.3150
5.5118
40
44
44
1.5748
1.7323
1.7323
135 000
163 000
159 000
30 350
36 650
35 750
320 000
390 000
390 000
51317
51318
51320
85
90
100
3.3465
3.5433
3.9370
150
155
170
5.9055
6.1024
6.6929
49
50
55
1.9291
1.9685
2.1654
190 000
195 000
229 000
42 720
43 840
51 480
51322 M
51324 M
51324 M
110
120
130
4.3307
4.7244
5.1181
190
210
225
7.4803
8.2677
8.8583
63
70
75
2.4803
2.7559
2.9528
276 000
325 000
325 000
51328 M
51330 M
51332 M
140
150
160
5.5118
5.9055
6.2992
240
250
270
9.4488
9.8425
10.6299
80
80
87
3.1496
3.1496
3.4252
51334 M
51336 M
51340 M
170
180
200
6.6929
7.0866
7.8740
280
300
340
11.0236
11.8110
13.3858
87
95
110
3.4252
3.7402
4.3307
kg
lb
6 300
5 300
4 800
0.17
0.26
0.39
0.40
0.60
0.90
3 000
2 800
2 600
4 300
4 000
3 600
0.53
0.66
0.94
1.20
1.50
2.10
260
260
300
2 200
2 200
2 000
3 200
3 000
3 000
1.30
1.35
1.50
2.90
3.00
3.40
71 940
87 680
87 680
530
790
790
1 900
1 700
1 700
2 600
2 400
2 400
2.00
2.60
2.70
4.50
5.80
6.00
465 000
500 000
610 000
104 540
112 400
137 130
1 100
1 300
1 900
1 600
1 500
1 400
2 200
2 200
1 900
3.55
3.80
4.95
7.90
8.40
11.00
62 050
73 060
73 060
780 000
980 000
980 000
175 350
220 310
220 310
3 200
5 000
6 800
1 200
1 100
1 100
1 700
1 500
1 500
7.85
11.00
11.00
17.40
24.30
24.30
397 000
410 000
449 000
89 250
92 170
100 940
1 320 000
1 400 000
1 660 000
296 740
314 720
373 170
9 100
10 000
14 000
950
900
850
1 300
1 300
1 200
15.50
16.50
21.00
34.20
36.40
46.30
468 000
520 000
624 000
105 210
116 900
140 280
1 760 000
2 000 000
2 600 000
395 650
449 600
584 480
16 000
21 000
35 000
800
750
630
1 100
1 100
900
22.00
28.50
44.50
48.60
62.90
98.20
100
Mass

Single direction
Standard
Series: 51405 51424 M
Size: 25 mm 120 mm
0.9843 in 4.7244 in
Single direction
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed
speed
r/min
r/min
mm
in
51405
51406
51407
25
30
35
0.9843
1.1811
1.3780
60
70
80
2.3622
2.7559
3.1496
24
28
32
0.9449
1.1024
1.2598
55 300
72 800
87 100
12 440
16 370
19 590
96 500
137 000
170 000
21 700
30 800
38 220
48
97
150
3 600
3 000
2 600
51408
51409
51410
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
36
39
43
1.4173
1.5354
1.6929
112 000
130 000
159 000
25 180
29 230
35 750
224 000
265 000
340 000
50 360
59 580
76 440
260
370
600
51411
51412 M
51413 M
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
48
51
56
1.8898
2.0079
2.2047
178 000
199 000
216 000
40 020
44 740
48 560
390 000
430 000
490 000
87 680
96 670
110 160
51414 M
51415 M
51416 M
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
60
65
68
2.3622
2.5591
2.6772
234 000
251 000
270 000
52 610
56 430
60 700
550 000
610 000
670 000
51417 M
51418 M
51420 M
85
90
100
3.3465
3.5433
3.9370
180
190
210
7.0866
7.4803
8.2677
72
77
85
2.8346
3.0315
3.3465
286 000
307 000
371 000
64 300
69 020
83 410
51422 M
51424 M
110
120
4.3307
4.7244
230
250
9.0551
9.8425
95
102
3.7402
4.0157
410 000
520 000
92 170
116 900
Mass
kg
lb
5 000
4 300
3 800
0.34
0.52
0.79
0.80
1.20
1.80
2 400
2 200
2 000
3 400
3 000
2 800
1.10
1.40
2.00
2.50
3.10
4.50
790
960
1 200
1 800
1 600
1 500
2 400
2 200
2 200
2.55
3.10
4.00
5.70
6.90
8.90
123 640
137 130
150 620
1 600
1 900
2 300
1 400
1 300
1 200
2 000
1 800
1 700
5.00
6.75
7.95
11.10
14.90
17.60
750 000
815 000
1 060 000
168 600
183 220
238 290
2 900
3 500
5 800
1 200
1 100
950
1 600
1 500
1 400
9.45
11.00
15.00
20.90
24.30
33.10
1 220 000
1 730 000
274 260
388 910
7 700
16 000
900
800
1 300
1 100
20.00
29.50
44.10
65.10
101
Thrust bearings
Double direction
Standard
Series: 52202 52234 M
Size: 10 mm 150 mm
0.3937 in 5.9055 in
Double direction
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Mass
Reference Limiting
speed speed
r/min r/min
kg
mm
in
52202
52204
52205
10
15
20
0.3937
0.5906
0.7874
32
40
47
1.2598
1.5748
1.8504
22
26
28
0.8661
1.0236
1.1024
16 500
22 500
27 600
3 710
5 060
6 210
27 000
40 500
55 000
6 100
9 200
12 400
3.8
8.5
15
7 000 10 000
6 000 8 000
5 300 7 500
0.08
0.15
0.22
0.20
0.30
0.50
52206
52207
52208
25
30
30
0.9843
1.1811
1.1811
52
62
68
2.0472
2.4409
2.6772
29
34
36
1.1417
1.3386
1.4173
25 500
35 100
46 800
5 740
7 900
10 600
51 000
73 500
106 000
11 500
16 600
23 900
13
28
58
4 800
4 000
3 800
6 700
5 600
5 300
0.25
0.41
0.55
0.60
0.90
1.20
52209
52210
52211
35
40
45
1.3780
1.5748
1.7717
73
78
90
2.8740
3.0709
3.5433
37
39
45
1.4567
1.5354
1.7717
39 000
49 400
61 800
8 770
11 200
13 900
86 500
116 000
146 000
19 500
26 100
32 900
38
69
110
3 600
3 400
2 800
5 000
4 500
4 000
0.60
0.71
1.10
1.30
1.60
2.40
52212
52213
52215
50
55
60
1.9685
2.1654
2.3622
95
100
110
3.7402
3.9370
4.3307
46
47
47
1.8110
1.8504
1.8504
62 400
63 700
67 600
14 030
14 400
15 200
150 000
163 000
183 000
33 800
36 700
41 200
120
140
170
2 800
2 600
2 400
3 800
3 600
3 400
1.20
1.35
1.55
2.60
3.00
3.40
52216
52217
52218
65
70
75
2.5591
2.7559
2.9528
115
125
135
4.5276
4.9213
5.3150
48
55
62
1.8898
2.1654
2.4409
76 100
97 500
119 000
17 200
22 000
26 800
208 000
275 000
325 000
46 800
61 900
73 100
220
390
550
2 400
2 200
2 000
3 400
3 000
2 800
1.70
2.40
3.20
3.70
5.30
7.10
52220
52222
52224
85
95
100
3.3465
3.7402
3.9370
150
160
170
5.9055
6.2992
6.6929
67
67
68
2.6378
2.6378
2.6772
124 000
130 000
140 000
27 900
29 300
31 500
345 000
390 000
440 000
77 600
87 700
99 000
620
790
1 000
1 800
1 700
1 600
2 400
2 400
2 200
4.20
4.65
5.25
9.30
10.30
11.60
52226
52228
52230 M
110
120
130
4.3307
4.7244
5.1181
190
200
215
7.4803
7.8740
8.4646
80
81
89
3.1496
3.1890
3.5039
186 000
190 000
238 000
41 900
42 800
53 600
585 000
620 000
800 000
131 600
139 400
179 900
1 800
2 000
3 300
1 400
1 400
1 300
2 000
1 900
1 800
8.00
8.65
11.50
17.60
19.10
25.40
52232 M
52234 M
140
150
5.5118
5.9055
225
240
8.8583
9.4488
90
97
3.5433
3.8189
242 000
286 000
54 500
64 300
850 000
1 020 000
191 100
229 300
3 800
5 400
1 200
1 100
1 700
1 800
12.00
15.00
26.50
33.10
102
lb

Double direction
Standard
Series: 52305 52320
Size: 20 mm 85 mm
0.7874 in 3.3465 in
Series: 52406 52414 M
Size: 20 mm 55 mm
0.7874 in 2.7559 in
Double direction
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed speed
r/min r/min
Mass
mm
in
kg
lb
52305
52306
52307
20
25
30
0.7874
0.9843
1.1811
52
60
68
2.0472
2.3622
2.6772
34
38
44
1.3386
1.4961
1.7323
34 500
37 700
49 400
7 800
8 500
11 110
60 000
71 000
96 500
13 500
16 000
21 700
18
26
48
4 500
3 800
3 400
6 300
5 300
4 800
0.33
0.47
0.68
0.70
1.00
1.50
52308
52309
52310
30
35
40
1.1811
1.3780
1.5748
78
85
95
3.0709
3.3465
3.7402
49
52
58
1.9291
2.0472
2.2835
61 800
76 100
88 400
13 900
17 200
19 900
122 000
153 000
190 000
27 500
34 400
42 800
77
120
190
3 000
2 800
2 600
4 300
4 000
3 600
1.05
1.25
1.75
2.30
2.80
3.90
52311
52312
52313
45
50
55
1.7717
1.9685
2.1654
105
110
115
4.1339
4.3307
4.5276
64
64
65
2.5197
2.5197
2.5591
104 000
101 000
106 000
23 380
22 800
23 900
224 000
224 000
240 000
50 400
50 400
54 000
260
260
300
2 200
2 200
2 000
3 200
3 000
3 000
2.40
2.55
2.75
5.30
5.60
6.10
52314
52315
52316
55
60
65
2.1654
2.3622
2.5591
125
135
140
4.9213
5.3150
5.5118
72
79
79
2.8346
3.1102
3.1102
135 000
163 000
159 000
30 350
36 650
35 750
320 000
390 000
390 000
72 000
87 700
87 700
530
790
790
1 900
1 700
1 700
2 600
2 400
2 400
3.65
4.80
4.94
8.00
10.60
10.90
52320
85
3.3465
170
6.6929
97
3.8189
229 000
51 480
610 000
137 200
1 900
1 400
1 900
8.95
19.70
52406
52407
52408
20
25
30
0.7874
0.9843
1.1811
70
80
90
2.7559
3.1496
3.5433
52
59
65
2.0472
2.3228
2.5591
72 800
87 100
112 000
16 370
19 590
25 180
137 000
170 000
224 000
30 800
38 300
50 400
97
150
260
3 000
2 600
2 400
4 300
3 800
3 400
1.00
1.45
2.05
2.20
3.20
4.50
52409
52411
52412 M
35
45
50
1.3780
1.7717
1.9685
100
120
130
3.9370
4.7244
5.1181
72
87
93
2.8346
3.4252
3.6614
130 000
170 800
199 000
29 300
38 400
44 800
265 000
390 000
430 000
59 600
87 700
96 700
370
790
960
2 200
1 800
1 600
3 000
2 400
2 200
2.70
4.70
6.35
6.00
10.40
14.00
52413 M
52414 M
50
55
1.9685
2.7559
140
150
5.5118
5.9055
101
107
3.9764
4.2126
216 000
234 000
48 600
52 700
490 000
550 000
110 200
123 700
1 200
1 600
1 500
1 400
2 100
2 000
8.03
9.71
17.70
21.40
103
Thrust bearings
Single direction, sphered housing washer
Standard
Series: 53201 53228
Size: 12 mm 140 mm
0.4724 in 5.5118 in
Single direction with sphered housing washer

For D3 and H1 dimension refer to table 1 on pages 94 and 95.
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings
Height
H
mm
in
Dynamic
C
N
lbf
Static
C0
N
lbf
Minimum Speed rating

Mass
load
factor
Reference Limiting
speed speed
A
r/min r/min
kg
lb
Seating
washer
Mass
kg
lb
53201
53202
53203
12
15
17
0.4724
0.5906
0.6693
28
32
35
1.1024
1.2598
1.3780
11
13
13
0.4488
0.5236
0.5197
13 300
16 500
17 200
3 000
3 700
3 900
20 800
27 000
30 000
4 700
6 100
6 700
2.2
3.8
4.7
8 000 11 000
7 000 10 000
6 700 9 500
0.05
0.06
0.07
0.1
0.1
0.2
U 201
U 202
U 203
0.01
0.01
0.02
0.03
0.03
0.03
53204
53205
53206
20
25
30
0.7874
0.9843
1.1811
40
47
52
1.5748
1.8504
2.0472
15
17
18
0.5787
0.6575
0.7008
22 500
27 600
25 500
5 100
6 200
5 700
40 500
55 000
51 000
9 100
12 400
11 500
8.5
15
13
6 000
5 300
4 800
8 000
7 500
6 700
0.10
0.15
0.18
0.2
0.3
0.4
U 204
U 205
U 206
0.02
0.03
0.04
0.04
0.07
0.08
53207
53208
53209
35
40
45
1.3780
1.5748
1.7717
62
68
73
2.4409
2.6772
2.8740
20
20
21
0.7835
0.7992
0.8386
35 100
46 800
39 000
7 900
10 500
8 800
73 500
106 000
86 500
16 500
23 800
19 400
28
58
38
4 000
3 800
3 600
5 600
5 300
5 000
0.28
0.35
0.39
0.6
0.8
0.9
U 207
U 208
U 209
0.06
0.07
0.09
0.13
0.15
0.19
53210
53211
53212
50
55
60
1.9685
2.1654
2.3622
78
90
95
3.0709
3.5433
3.7402
24
27
28
0.9252
1.0748
1.1024
49 400
61 800
62 400
11 100
13 900
14 000
116 000
146 000
150 000
26 100
32 800
33 700
69
110
120
3 400
2 800
2 800
4 500
4 000
3 800
0.47
0.75
0.82
1.0
1.7
1.8
U 210
U 211
U 212
0.10
0.15
0.16
0.22
0.33
0.35
53213
53214
53215
65
70
75
2.5591
2.7559
2.9528
100
105
110
3.9370
4.1339
4.3307
29
29
28
1.1299
1.1339
1.1142
63 700
65 000
67 600
14 300
14 600
15 200
163 000
173 000
183 000
36 600
38 900
41 100
140
160
170
2 600
2 600
2 400
3 600
3 600
3 400
0.91
0.97
1.00
2.0
2.1
2.2
U 213
U 214
U 215
0.18
0.19
0.21
0.40
0.42
0.46
53216
53217
53218
80
85
90
3.1496
3.3465
3.5433
115
125
135
4.5276
4.9213
5.3150
30
33
39
1.1614
1.3031
1.5157
76 100
97 500
119 000
17 100
21 900
26 800
208 000
275 000
325 000
46 800
61 800
73 100
220
390
550
2 400
2 200
2 000
3 400
3 000
2 800
1.10
1.50
2.10
2.4
3.3
4.6
U 216
U 217
U 218
0.22
0.29
0.42
0.49
0.64
0.93
53220
53222
53226
100
110
130
3.9370
4.3307
5.1181
150
160
190
5.9055
6.2992
7.4803
41
40
48
1.6102
1.5827
1.8858
124 000
130 000
186 000
27 900
29 200
41 800
345 000
390 000
585 000
77 600
87 700
131 500
620
790
1 800
1 800
1 700
1 400
2 400
2 400
2 000
2.70
6.0
2.91
6.4
4.85 10.7
U 220
U 222
U 226
0.50
0.56
0.90
1.10
1.25
2.00
53228
140
5.5118
200
7.8740
49
1.9134
190 000
42 700
620 000
139 400
2 000
1 400
1 900
5.45 12.0
U 228
1.20
2.65
104

Single direction, sphered housing washer
Standard
Series: 53306 53326
Size: 30 mm 130 mm
1.1811 in 5.1181 in
Series: 53408 53420 M
Size: 40 mm 100 mm
1.5748 in 3.9370 in
Single direction with sphered housing washer

Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings
Height
H
mm
in
Dynamic
C
N
lbf
Static
C0
N
lbf

Mass
load
factor
Reference Limiting
speed
speed
A
r/min r/min
kg
lb
Seating
washer
Mass
kg
lb
53306
53307
53308
30
35
40
1.1811
1.3780
1.5748
60
68
78
2.3622
2.6772
3.0709
23
26
29
0.8898
1.0079
1.1220
37 700
49 400
61 800
8 500
11 100
13 900
71 000
96 500
122 000
16 000
21 700
27 400
26
48
77
3 800 5 300
3 400 4 800
3 000 4 300
0.33
0.46
0.67
0.7
1.0
1.5
U 306
U 307
U 308
0.06
0.08
0.12
0.12
0.19
0.26
53309
53310
53311
45
50
55
1.7717
1.9685
2.1654
85
95
105
3.3465
3.7402
4.1339
30
34
39
1.1850 76 100
1.3543 88 400
1.5472 104 000
17 100
19 900
23 400
153 000
190 000
224 000
34 400
42 700
50 400
120
190
260
2 800 4 000
2 600 3 600
2 200 3 200
0.83
1.20
1.68
1.8
2.6
3.7
U 309
U 310
U 311
0.17
0.23
0.28
0.37
0.51
0.62
53312
53313
53314
60
65
70
2.3622
2.5591
2.7559
110
115
125
4.3307
4.5276
4.9213
38
39
44
1.5079 101 000

1.5512 106 000
1.7402 135 000
22 700
23 800
30 300
224 000
240 000
320 000
50 400
54 000
71 900
260
300
530
2 200 3 000
2 000 3 000
1 900 2 600
1.71
1.89
2.50
3.8
4.2
5.5
U 312
U 313
U 314
0.31
0.34
0.41
0.68
0.75
0.90
53315
53316
53317
75
80
85
2.9528
3.1496
3.3465
135
140
150
5.3150
5.5118
5.9055
48
48
53
1.8937 163 000

1.8740 159 000
2.0906 190 000
36 600
35 700
42 700
390 000
390 000
465 000
87 700
87 700
104 500
790
790
1 100
1 700 2 400
1 700 2 400
1 600 2 200
3.20
3.30
4.35
7.1
7.3
9.6
U 315
U 316
U 317
0.55
0.57
0.81
1.20
1.25
1.80
53318
53320
53322 M
90
100
110
3.5433
3.9370
4.3307
155
170
190
6.1024
6.6929
7.4803
55
59
67
2.1496 195 000

2.3307 229 000
2.6457 276 000
43 800
51 500
62 000
500 000
610 000
780 000
112 400
137 100
175 300
1 300
1 900
3 200
1 500 2 200
1 400 1 900
1 200 1 700
4.70 10.4
5.95 13.1
9.10 20.1
U 318
U 320
U 322
0.84
0.95
1.30
1.85
2.10
2.85
53324 M
53326
120
130
4.7244
5.1181
210
190
8.2677
7.4803
74
53
2.9173 325 000

2.0866 186 000
73 100
41 800
980 000
585 000
220 300
131 500
5 000
1 800
1 100 1 500
1 400 2 000
12.50 27.6
4.85 10.7
U 324
U 226
2.00
0.90
4.40
2.00
53408
53409
53410
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
38
42
46
1.5039 112 000

1.6693 130 000
1.7953 159 000
25 200
29 200
35 700
224 000
265 000
340 000
50 400
59 600
76 400
2 600
3 700
600
2 400 3 400
1 900 2 800
2 000 2 800
1.35
1.45
2.31
3.0
3.2
5.1
U 408
U 409
U 410
0.25
0.32
0.41
0.55
0.71
0.90
53411
53412 M
53414 M
55
60
70
2.1654
2.3622
2.7559
120
130
150
4.7244
5.1181
5.9055
55
54
69
2.1654 178 000

2.1260 199 000
2.7165 234 000
40 000
44 700
52 600
390 000
430 000
550 000
87 700
96 700
123 600
790
960
1 600
1 800 2 400
1 600 2 200
1 400 2 000
3.08
6.8
3.80
8.4
6.50 14.3
U 411
U 412
U 414
0.53
0.71
0.99
1.17
1.55
2.18
53420 M
100
3.9370
210
8.2677
90
3.5433 371 000
83 400 1 060 000
238 300
5 800
950 1 400
18.00 39.7
U 420
2.90
6.40
105
Thrust bearings
Double direction, sphered housing washer
Standard
Series: 54207 54211
Size: 30 mm 45 mm
1.1811 in 1.7717 in
Series: 54306 54317
Size: 25 mm 70 mm
0.9843 in 2.7559 in
Series: 54410
Size: 40 mm (1.5748 in)
Double direction with sphered housing washer
Designation
Principal Dimensions
Bore
d
mm
in
Outside Diameter
D
mm
in
Basic load ratings
Height
H
mm
in
Dynamic
C
N
lbf
Static
C0
N
lbf

Mass
load
factor
Reference Limiting
speed
speed
A
r/min r/min
kg
lb
Seating
washer
Mass
kg
lb
54207
54211
30
45
1.1811
1.7717
62
90
2.4409
3.5433
38
50
1.4882
1.9528
35 100
61 800
7 900
13 900
73 500
146 000
16 500
32 800
28
110
4 000
2 800
5 600
4 000
0.53
1.3
1.20
2.90
U 207
U 211
0.06
0.15
0.13
0.33
54306
54307
54309
25
30
35
0.9843
1.1811
1.3780
60
68
85
2.3622
2.6772
3.3465
41
47
56
1.6260
1.8583
2.2165
37 700
49 400
76 100
8 500
11 100
17 100
71 000
96 500
153 000
16 000
21 700
34 400
26
48
120
3 800
3 400
2 800
5 300
4 800
4 000
0.58
0.85
1.6
1.30
1.90
3.50
U 306
U 307
U 309
0.06
0.08
0.17
0.12
0.19
0.37
54310
54312
54317
40
50
70
1.5748
1.9685
2.7559
95
110
150
3.7402
4.3307
5.9055
65
71
93
2.5472 88 400
2.7835 101 000
3.6417 190 000
19 900
22 700
42 700
190 000
224 000
465 000
42 700
50 400
104 500
190
260
1 100
2 600
2 200
1 600
3 600
3 000
2 200
2.3
5.10
2.9
6.40
7.95 17.50
U 310
U 312
U 317
0.23
0.31
0.81
0.51
0.68
1.80
54410
40
1.5748
110
4.3307
83
3.2756 159 000
35 700
340 000
76 400
600
2 000
2 800
4.45
U 410
0.46
1.00
9.80
106

Standard
Series: 29230 E 292/1180 EF
5.9055 in 46.4567 in
Standard design
Designation
E design
Bore
d
mm
in
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed speed
r/min r/min
Mass
kg
lb
29230 E
29236 E
29240 E
150
180
200
5.9055
7.0866
7.8740
215
250
280
8.4646
9.8425
11.0236
39
42
48
1.5354
1.6535
1.8898
408 000
495 000
656 000
91 700
111 300
147 500
1 600 000
2 040 000
2 650 000
359 700
458 600
595 700
240 1 800
400 1 600
670 1 400
2 800
2 600
2 200
4.30
5.80
9.30
9.50
12.80
20.50
29244 E
29248
29252
220
240
260
8.6614
9.4488
10.2362
300
340
360
11.8110
13.3858
14.1732
48
60
60
1.8898
2.3622
2.3622
690 000
799 000
817 000
155 100
179 600
183 700
3 000 000
3 450 000
3 650 000
674 400
775 600
820 500
860 1 300
1 100 1 100
1 300 1 100
2 200
1 800
1 700
10.00
16.50
18.50
22.00
36.40
40.80
29256
29260
29264
280
300
320
11.0236
11.8110
12.5984
380
420
440
14.9606
16.5354
17.3228
60
73
73
2.3622
2.8740
2.8740
863 000
1 070 000
1 110 000
194 000
240 500
249 500
4 000 000
4 800 000
5 100 000
900 000
1 080 000
1 147 000
1 500 1 000
2 200
900
2 500
850
1 700
1 400
1 400
19.50
30.50
33.00
43.00
67.20
72.80
29268
29272
29276
340
360
380
13.3858
14.1732
14.9606
460
500
520
18.1102
19.6850
20.4724
73
85
85
2.8740
3.3465
3.3465
1 130 000
1 460 000
1 580 000
254 000
328 200
355 200
5 400 000
6 800 000
7 650 000
1 214 000
1 529 000
1 720 000
2 800
4 400
5 600
850
750
700
1 300
1 200
1 100
33.50
52.00
53.00
73.90
114.60
116.80
29280
29284
29288
400
420
440
15.7480
16.5354
17.3228
540
580
600
21.2598
22.8346
23.6220
85
95
95
3.3465
3.7402
3.7402
1 610 000
1 990 000
2 070 000
361 900 8 000 000

447 400 9 800 000
465 300 10 400 000
1 799 000
2 204 000
2 338 000
6 100
9 100
10 000
700
630
630
1 100
1 000
1 000
55.50
75.50
78.00
122.40
166.40
172.00
29292
29296
292/500
460
480
500
18.1102
18.8976
19.6850
620
650
670
24.4094
25.5906
26.3780
95
103
103
3.7402
4.0551
4.0551
2 070 000
2 350 000
2 390 000
465 300 10 600 000

528 300 11 800 000
537 300 12 500 000
2 383 000
2 653 000
2 810 000
11 000
13 000
15 000
600
560
560
950
900
900
81.00
98.00
100.00
178.60
216.10
230.00
292/560 EM
292/600 EM
292/630 EM
560
600
630
22.0472
23.6220
24.8031
750
800
850
29.5276
31.4961
33.4646
115
122
132
4.5276
4.8031
5.1969
2 990 000
672 200 16 000 000
3 740 000
840 800 18 600 000
4 770 000 1 072 300 23 600 000
3 597 000
4 182 000
5 306 000
24 000
33 000
53 000
480
450
400
800
700
670
140.00
170.00
210.00
310.00
380.00
470.00
292/670
292/750 EM
292/800 EM
670
750
800
26.3780
900
29.5276 1 000
31.4961 1 060
35.4331
39.3701
41.7323
140
150
155
5.5118
5.9055
6.1024
4 200 000
944 200 22 800 000
6 100 000 1 371 300 31 000 000
6 560 000 1 474 700 34 500 000
5 126 000 49 000

6 969 000 91 000
7 756 000 110 000
380
340
320
630
560
530
255.00
325.00
380.00
570.00
720.00
840.00
292/850 EM
850
292/950 EM
950
292/1060 EF 1 060
33.4646 1 120
37.4016 1 250
41.7323 1 400
44.0945
49.2126
55.1181
160
180
206
6.2992 6 730 000 1 513 000 36 000 000 8 093 000 120 000
7.0866 8 280 000 1 861 400 45 500 000 10 229 000 200 000
8.1102 10 500 000 2 361 000 58 500 000 13 151 000 330 000
300
260
220
500
430
360
425.00 940.00
600.00 1320.00
860.00 1900.00
292/1180 EF 1 180
46.4567 1 520
59.8425
206
8.1102 10 900 000 2 451 000 64 000 000 14 388 000 390 000
220
340
950.00 2100.00
107
Thrust bearings
Series: 29317 E 293/530
Size: 85 mm 530 mm
3.3465 in 20.8661 in
Standard design
Designation
E design
EM design
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Height
H
mm
in
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
lbf
Speed rating
Reference Limiting
speed speed
r/min r/min
Mass
mm
in
29317 E
29318 E
29320 E
85
90
100
3.3465
3.5433
3.9370
150
155
170
5.9055
6.1024
6.6929
39
39
42
1.5354
1.5354
1.6535
380 000
400 000
465 000
85 500
90 000
104 600
1 060 000
1 080 000
1 290 000
238 300
242 800
290 000
110
110
160
2 400
2 400
2 200
4 000
4 000
3 600
2.75
2.85
3.65
6.10
6.30
8.00
29322 E
29324 E
29326 E
110
120
130
4.3307
4.7244
5.1181
190
210
225
7.4803
8.2677
8.8583
48
54
58
1.8898
2.1260
2.2835
610 000
765 000
865 000
137 200
172 000
194 500
1 730 000
2 120 000
2 500 000
389 000
476 600
562 000
280
430
590
1 900
1 700
1 600
3 200
2 800
2 600
5.30
7.35
9.00
11.70
16.20
19.80
29328 E
29330 E
29332 E
140
150
160
5.5118
5.9055
6.2992
240
250
270
9.4488
9.8425
10.6299
60
60
67
2.3622
2.3622
2.6378
980 000
1 000 000
1 180 000
220 400
224 800
265 300
2 850 000
2 850 000
3 450 000
640 700
640 700
775 600
770
770
110
1 500
1 500
1 300
2 600
2 400
2 200
10.50
11.00
14.50
23.10
24.30
32.00
29334 E
29336 E
29338 E
170
180
190
6.6929
7.0866
7.4803
280
300
320
11.0236
11.8110
12.5984
67
73
78
2.6378
2.8740
3.0709
1 200 000
1 430 000
1 630 000
269 800
321 500
366 500
3 550 000
798 100
4 300 000
966 700
4 750 000 1 067 800
1 200
1 800
2 100
1 300
1 200
1 100
2 200
2 000
1 900
15.00
19.50
23.50
33.10
43.00
51.80
29340 E
29344 E
29348 E
200
220
240
7.8740
8.6614
9.4488
340
360
380
13.3858
14.1732
14.9606
85
85
85
3.3465
3.3465
3.3465
1 860 000
2 000 000
2 040 000
418 200
449 600
458 600
5 500 000 1 236 400

6 300 000 1 416 300
6 550 000 1 472 500
2 900
3 800
4 100
1 000
1 000
1 000
1 700
1 700
1 600
29.50
33.50
35.50
65.00
73.90
78.30
29352 E
29356 E
29360 E
260
280
300
10.2362
11.0236
11.8110
420
440
480
16.5354
17.3228
18.8976
95
95
109
3.7402
3.7402
4.2913
2 550 000
2 550 000
3 100 000
573 300 8 300 000 1 865 900

6 500
573 300 8 650 000 1 944 600
7 100
696 900 10 600 000 2 382 900 11 000
850
850
750
1 400
1 400
1 200
49.00
53.00
75.00
108.00
116.80
165.30
29364 E
29368
29372
320
340
360
12.5984
13.3858
14.1732
500
540
560
19.6850
21.2598
22.0472
109
122
122
4.2913
4.8031
4.8031
3 350 000
2 710 000
2 760 000
753 100 11 200 000 2 517 800 12 000

609 300 11 000 000 2 472 800 11 000
620 500 11 600 000 2 607 700 13 000
750
600
600
1 200
1 100
1 100
78.00
105.00
110.00
172.00
240.00
250.00
29376
29380
29384
380
400
420
14.9606
15.7480
16.5354
600
620
650
23.6220
24.4094
25.5906
132
132
140
5.1969
5.1969
5.5118
3 340 000
3 450 000
3 740 000
750 900 14 000 000 3 148 000 19 000

775 600 14 600 000 3 283 000 20 000
840 800 16 000 000 3 597 000 24 000
530
530
500
1 000
950
900
140.00
150.00
170.00
310.00
340.00
380.00
29388 EM
29392
29396
440
460
480
17.3228
18.1102
18.8976
680
710
730
26.7717
27.9528
28.7402
145
150
150
5.7087
5.9055
5.9055
4 490 000 1 009 400 19 300 000 4 339 000 35 000

4 310 000 968 900 19 000 000 4 272 000 34 000
4 370 000 982 400 19 600 000 4 407 000 36 000
480
450
450
850
800
800
180.00
215.00
220.00
400.00
480.00
490.00
293/500
293/530
500
530
19.6850
20.8661
750
800
29.5276
31.4961
150
160
5.9055
6.2992
4 490 000 1 009 400 20 400 000 4 586 000 40 000

5 230 000 1 175 800 23 600 000 5 306 000 53 000
430
400
800
750
235.00
270.00
520.00
600.00
108
kg
lb

Series: 293/630 EM 293/1250 EF
24.8031 in 49.2126 in
Series: 29412 E 29452 E
Size: 60 mm 260 mm
2.3622 in 10.2362 in
Standard design
Designation
E design
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Height
H
mm
in
mm
in
630
710
750
24.8031
27.9528
29.5276
950
1 060
1 120
37.4016
41.7323
44.0945
190
212
224
7.4803
8.3465
8.8189
293/800
800
293/1250 EF 1 250
31.4961
49.2126
1 180
1 800
46.4567
70.8661
230
330
9.0551
12.9921
293/630 EM
293/710 EM
293/750
Dynamic
C
N
Minimum
load
factor
Static
C0
lbf
8 450 000 1 899 600

9 950 000 2 236 800
9 370 000 2 106 400
lbf
Speed rating
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
lb
38 000 000
45 500 000
45 000 000
8 543 000
10 229 000
10 116 000
140 000
200 000
190 000
320
280
260
600
500
480
485.00
660.00
770.00
1070.00
1460.00
1700.00
9 950 000 2 236 800 49 000 000

24 800 000 5 575 100 129 000 000
11 016 000
29 000 000
230 000
1 600 000
240
130
450
240
865.00
2770.00
1910.00
6110.00
29412 E
29413 E
29414 E
60
65
70
2.3622
2.5591
2.7559
130
140
150
5.1181
5.5118
5.9055
42
45
48
1.6535
1.7717
1.8898
390 000
455 000
520 000
87 700
102 300
116 900
915 000
1 080 000
1 250 000
205 700
242 800
281 000
80
110
15 000
2 800
2 600
2 400
5 000
4 800
4 300
2.60
3.20
3.90
5.70
7.10
8.60
29415 E
29416 E
29417 E
75
80
85
2.9528
3.1496
3.3465
160
170
180
6.2992
6.6929
7.0866
51
54
58
2.0079
2.1260
2.2835
600 000
670 000
735 000
134 900
150 700
165 300
1 430 000
1 630 000
1 800 000
321 500
366 500
404 700
190
250
310
2 400
2 200
2 000
4 000
3 800
3 600
4.70
5.60
6.75
10.40
12.30
14.90
29418 E
29420 E
29422 E
90
100
110
3.5433
3.9370
4.3307
190
210
230
7.4803
8.2677
9.0551
60
67
73
2.3622
2.6378
2.8740
815 000
980 000
1 180 000
183 300
220 400
265 300
2 000 000
2 500 000
3 000 000
449 600
562 000
674 400
380
590
860
1 900
1 700
1 600
3 400
3 000
2 800
7.75
10.50
13.50
17.10
23.10
29.80
29424 E
29426 E
29428 E
120
130
140
4.7244
5.1181
5.5118
250
270
280
9.8425
10.6299
11.0236
78
85
85
3.0709
3.3465
3.3465
1 370 000
1 560 000
1 630 000
308 000
350 700
366 500
3 450 000
4 050 000
4 300 000
775 600
910 500
966 700
1 100
1 600
1 800
1 500
1 300
1 300
2 600
2 400
2 400
17.50
22.00
23.00
38.60
48.50
50.70
29430 E
29432 E
29434 E
150
160
170
5.9055
6.2992
6.6929
300
320
340
11.8110
12.5984
13.3858
90
95
103
3.5433
3.7402
4.0551
1 860 000
2 080 000
2 360 000
418 200
467 600
530 600
5 100 000
5 600 000
6 550 000
1 146 500
1 258 900
1 472 500
2 500
3 000
4 100
1 200
1 100
1 100
2 200
2 000
1 900
28.00
33.50
44.50
61.70
73.90
98.10
29436 E
29438 E
29440 E
180
190
200
7.0866
7.4803
7.8740
360
380
400
14.1732
14.9606
15.7480
109
115
122
4.2913
4.5276
4.8031
2 600 000
2 850 000
3 200 000
584 500
640 700
719 400
7 350 000
8 000 000
9 000 000
1 652 300
1 798 400
2 023 200
5 100
6 100
7 700
1 000
950
850
1 800
1 700
1 600
52.50
60.50
72.00
115.70
133.40
158.70
29444 E
29448 E
29452 E
220
240
260
8.6614
9.4488
10.2362
420
440
480
16.5354
17.3228
18.8976
122
122
132
4.8031
4.8031
5.1969
3 350 000
3 400 000
4 050 000
753 100
764 400
910 500
9 650 000
10 200 000
12 900 000
2 169 400
2 293 000
2 900 000
8 800
9 900
16 000
850
850
750
1 500
1 500
1 300
75.00
80.00
105.00
165.30
176.40
240.00
109
Thrust bearings
Series: 29456 E 294/1060 EF
11.0236 in 41.7322 in
Designation
E design
EM design
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Height
H
mm
in
Dynamic
C
Static
C0
N
lbf
Reference Limiting
speed speed
r/min r/min
Mass
in
29456 E
29460 E
29464 E
280
300
320
11.0236
11.8110
12.5984
520
540
580
20.4724
21.2598
22.8346
145
145
155
5.7087
5.7087
6.1024
4 900 000 1 102 000

4 310 000
969 000
4 950 000 1 113 000
15 300 000
16 600 000
19 000 000
3 440 000
3 732 000
4 272 000
22 000
26 000
34 000
670
600
560
1 200
1 200
1 100
135.00
140.00
175.00
300.00
310.00
390.00
29468 E
29472 EM
29476 EM
340
360
380
13.3858
14.1732
14.9606
620
640
670
24.4094
25.1969
26.3780
170
170
175
6.6929
6.6929
6.8898
5 750 000 1 293 000

5 350 000 1 203 000
5 870 000 1 320 000
22 400 000
21 200 000
24 000 000
5 036 000
4 766 000
5 396 000
48 000
43 000
55 000
500
500
480
1 000
950
900
220.00
230.00
260.00
490.00
510.00
580.00
29480 EM
29484 EM
29488 EM
400
420
440
15.7480
16.5354
17.3228
710
730
780
27.9528
28.7402
30.7087
185
185
206
7.2835
7.2835
8.1102
6 560 000 1 475 000

6 730 000 1 513 000
7 820 000 1 758 000
26 500 000
27 500 000
32 000 000
5 958 000
6 182 000
7 194 000
67 000
72 000
87 000
450
430
380
850
850
750
310.00
325.00
410.00
690.00
720.00
910.00
29492 EM
29496 EM
294/500 EM
460
480
500
18.1102
18.8976
19.6850
800
850
870
31.4961
33.4646
34.2520
206
224
224
8.1102
8.8189
8.8189
7 990 000 1 797 000

9 550 000 2 147 000
9 370 000 2 107 000
33 500 000
39 000 000
40 000 000
7 531 000
8 768 000
8 992 000
110 000
140 000
150 000
380
340
340
750
670
670
425.00 940.00
550.00 1220.00
560.00 1240.00
294/530 EM
294/560 EM
294/600 EM
530
560
600
20.8661
920
22.0472
980
23.6220 1 030
36.2205
38.5827
40.5512
236
250
258
9.2913
9.8425
10.1575
10 500 000 2 361 000

12 000 000 2 698 000
13 100 000 2 945 000
44 000 000 9 892 000

51 000 000 11 465 000
56 000 000 12 589 000
180 000
250 000
300 000
320
300
280
630
560
530
650.00 1440.00
810.00 1790.00
845.00 1870.00
294/630 EM
294/670 EF
294/710 EF
630
670
710
24.8031 1 090
26.3780 1 150
27.9528 1 220
42.9134
45.2756
48.0315
280
290
308
11.0236
11.4173
12.1260
14 400 000 3 238 000

15 400 000 3 462 000
17 600 000 3 957 000
62 000 000 13 938 000

68 000 000 15 287 000
76 500 000 17 198 000
370 000
440 000
560 000
260
240
220
500
450
430
1040.00 2300.00
1210.00 2670.00
1500.00 3310.00
294/750 EF
294/800 EF
750
800
29.5276 1 280
31.4961 1 360
50.3937
53.5433
315
335
12.4016
13.1890
18 700 000 4 204 000

20 200 000 4 541 000
85 000 000 19 108 000

93 000 000 20 907 000
690 000
820 000
200
190
400
360
1650.00 3640.00
2025.00 4470.00
35.4330
37.4015
41.7322
59.8424
62.9920
69.6849
372
390
426
14.6456 26 700 000 6 003 000 122 000 000 27 430 000 1 400 000
15.3543 28 200 000 6 340 000 132 000 000 29 700 000 1 700 000
16.77162 33 400 000 7 510 000 156 000 000 35 100 000 2 300 000
160
140
120
300
280
240
2650.00 5850.00
3065.00 6760.00
4280.00 9440.00
1520
1600
1770
lbf
Speed rating
mm
294/900 EF
900
294/950 EF
950
294/1060 EF 1060
Minimum
load
factor
110
kg
lb
Cylindrical roller
bearings
Nomenclature
N 310 EC M / C3 V W23B
1
3
2
1. Basic design:
2. Internal design:
4. Radial internal clearance:
Two integral flanges on

inner ring, flangeless outer ring
EC
C1
Clearance < C2
NU
C2
Clearance < Normal

outer ring, flangeless inner ring
(C0)*
Normal internal clearance
C3
Clearance > Normal
C4
Clearance > C3
NJ
One flange on inner ring,

two flanges on outer ring
NUP

outer ring, one integral
flange on inner ring and
one loose flange on inner ring
NCF
NJG
NNCF
Full complement, two flanges

on inner ring, one flange
on outer ring, with snap ring
Full complement with one
flange on inner ring, and two
flanges on outer ring
Two-row, full complement,
three flanges on inner ring,
one flange on outer ring,
with snap ring
Increased capacity plus

improved roller end to flange
contact
* Not marked on bearing or package
3. Cage designs:
5. Variations:
Two piece machined brass

cage, rolling element guided
Full complement bearing

without cage
MA
Two piece machined brass

cage, outer ring flange guided
BV
V + surface treated rollers
2LS
MB

inner ring flange guided
Two land riding

contact seals
ML/MP
One piece window-type

brass cage, inner or outer
ring centered
NNF
Two-row, full complement
NNCL
Double row CRB with no outer

ring integral flanges, only one
centrally located snap ring
M2
Double row CRB with one outer

ring integral flange and one
flange ring
Pressed steel cage,

Molded glass fiber reinforced

polyamide 6.6 cage,
roller centered
NNC
PHA
Solid brass drilled cage,

roller guided for traction
motor bearings
6. Special features:
W23B
Special features for

traction motor bearings
VA301
Special bearing
specifications
for traction motors
VL0241
INSOCOAT coating on
inner ring for electrical
insulation
Injection molded cage of

polyetheretherketone (PEEK),
outer ring centered
113
Cylindrical roller bearings
Product
Details
Technical
features
Boundary dimensions
Tolerances
ABMA RBEC 3, ISO P6 running accuracy

ABMA RBEC 1, ISO Normal dimensional
Heat stabilization
302 F (150 C)
Misalignment
4 minutes of arc for series N200, 300, 400,

1000 and 1800
3 minutes of arc for series N2200, 2300,
2900 and 3000
Cage material
Single row
cylindrical roller bearing
114
Standard
Molded glass fiber reinforced polyamide (P)
Optional
Machined brass (M) and pressed steel (J)
Axial load max
Contact SKF Applications Engineering
Seals
2LS seals on NNF series only
Full complement, single row

Full complement, double row

Introduction
Introduction
SKF manufactures many types and sizes of
cylindrical roller bearings, the majority being
single row bearings with a cage, but also
single or double row bearings with a full
complement of rollers.
All SKF cylindrical roller bearings represent
the latest state of the art. The contact geometry between roller and raceway has been
much improved by the introduction of the
logarithmic profile that provides for optimum
stress distribution in the bearing. Optimized
surface finishes favor lubricant film formation
and the correct rolling motion of the cylindrical
rollers. These improvements have considerably
increased the performance of SKF cylindrical
roller bearings as well as their operational
reliability in comparison with conventional
bearings, and have made them less sensitive
to misalignment.
Full complement cylindrical roller bearings
incorporate the maximum number of rollers
and, as a rule, have a low sectional height in
relation to their width. This produces an
extremely high load carrying capacity and
permits space-saving designs to be achieved.
Full complement cylindrical roller bearings are
suitable for very heavy radial loads; however,
the different kinematic conditions in the bearing mean that they cannot operate at the
same high speeds as cylindrical roller bearings
of the conventional caged type.
SKF produces single and double row full
complement cylindrical roller bearings as part
of the standard product range. The bearings
shown in the tables are standard range bearings but represent only part of the actual
manufactured range.
Basic design
Single row cylindrical roller bearings
The rollers of single row cylindrical roller bearings with cages are guided between integral
flanges on one of the bearing rings. The ring
with integral flanges and the roller and cage

assembly can be withdrawn from the other
ring. This facilitates mounting and dismounting
particularly where both rings need to have
interference fits because of the load conditions.
SKF single row cylindrical roller bearings have
high radial load carrying capacity and also high
speed capability. They are produced in different
designs that differ in the configuration of the
flanges (Figure 1).
The most popular of these bearings is the
NU type which has two integral flanges on the
outer ring and an inner ring without flanges
(Figure 1a). The N type has two integral
flanges on the inner ring and an outer ring
without flanges (Figure 1b).
Axial displacement of the shaft with respect
to the housing is permitted in both directions
within certain limits (Table 3a, page 119 for
dimension code s). For example, changes in
length because of thermal expansion can be
accommodated, and the bearings are therefore
suitable as non-locating bearings.
Cylindrical roller bearings of the NJ type have
two integral flanges on the outer ring and one
integral flange on the inner ring, so that axial
location can be provided for the shaft in one
direction (Figure 1c).
Type NUP cylindrical roller bearings have two
integral flanges on the outer ring and the inner
ring has one integral and one loose flange,
enabling the bearings to locate a shaft axially in
both directions (Figure 1d).
SKF Explorer class

bearings
SKF Explorer cylindrical roller bearings retain
the designation of earlier standard bearings,
e.g. NU 216 ECP. However, each bearing and its
box are marked with the name SKF Explorer,
to avoid confusion. In the product tables, the
SKF Explorer bearing designations are printed
in blue. Additional details on the SKF Explorer
page 23.
Product highlights
Logarithmically crowned rollers
sets SKF apart
SKF cylindrical roller bearings feature
logarithmically "crowned" rollers. This
roller profile reduces stresses under
high load conditions, while simultaneously providing excellent performance
under misaligned conditions.
High speed performance

Extended benefits of the logarithmic
profile roller are the cooler running
conditions and reliable performance
which allow for high speed running
conditions.
Precision-honed rolling
contact surfaces
SKF cylindrical roller bearings also
feature precision-honed inner and
outer rings, raceways and rollers. The
SKF honing process results in optimum
bearing performance and improved
lubricant effectiveness and quieter,
cooler, more reliable performance.

SKF manufactures cylindrical roller
bearings in single, double and multiple
row designs which differ in the
arrangement, design and construction
of the flanges. While caged bearings
are most common, several series with
a full compliment of rollers are also
available. Size range includes 25 to
1,000 mm inside diameter.
The large variety of sizes and types
of cylindrical roller bearings available
from SKF provides a wide degree of
application flexibility. Typical applications
include compressors, industrial gearboxes, transmissions, and final drives in
both on-road and off-road vehicles.
Customized solutions
Figure 1
a
NU
NJ
NUP
Special cages are available from SKF

for special application conditions such
as ammonia compressors and railroad
applications.
115

Introduction
ECdesign bearings
The EC design contains improvements in the
guiding surfaces of the flanges and of the roller
ends which means that the EC bearings have a
high axial load carrying capacity. The favorable
contact conditions also contribute to better
lubrication of the roller end/flange contact zone
and to lower operating temperatures. These
characteristics make SKF cylindrical roller
bearings of the EC design particularly useful.
They represent the standard design for the
most popular sizes of bearing series 10, 2, 22,
3 and 23.
Single row full complement cylindrical

roller bearings
SKF full complement cylindrical roller bearings
are produced as standard in the single row
NCF and NJG designs. (Figure 2).
Bearings of the NCF design are the most
popular and have two integral flanges on the
inner ring and one integral flange in the outer
ring and can thus locate the shaft in one
direction (Figure 2a). A retaining ring at the
flangeless side of the outer ring holds the
bearing together. The axial internal clearance in
the bearing is designed to permit small axial
displacements of the shaft in relation to the
housing to be accommodated within the
bearing (Table 3b, page 120).
Bearings of the NJG design all belong to the
heavy dimension series 23 and are intended
for very heavily loaded, slow-speed applications
(Figure 2b). In contrast to the other full
complement bearings, the NJG bearings have
a self-retaining roller complement. The outer
ring with its two integral flanges, together with
the roller complement, can be withdrawn from
the inner ring and there is no need to provide
any extra retention for the rollers. Mounting
and dismounting of these bearings are therefore simple operations. NJG design bearings
can support axial loads acting in one direction
and can consequently locate the shaft in one
direction.
Double row full complement cylindrical

roller bearings
Bearings of the NNF design (Figure 2f) are produced as standard with rubbing seals at both
sides. They are supplied filled with rust inhibiting
lithium grease having a diester oil base, which is
suitable for operation at temperatures between
-58 and +230 F (-50 and +110 C). However,
the permissible operating temperature for these
bearings is limited to -40 to +176 F (-40 to
+80 C) by the material used for the seals.
Under certain conditions, the sealed NNF
bearings are maintenance-free. However,
where they operate in the presence of moisture or contaminants, or where speeds are
moderate or high, they must be relubricated.
This can be achieved via both bearing rings. If
bearings are required without one or both seals,
they may be removed quite simply, for example,
using a screwdriver.
For applications where oil lubrication is to be
employed, the bearings can be delivered without
seals and grease if economic quantities are
involved. Otherwise the seals should be removed
and the bearings washed before use. If oil lubrication is adopted, the speed ratings can be
increased by approximately 30%.
There are several designs of SKF double row

full complement cylindrical roller bearings, all of
which have an annular groove and lubrication
holes in the outer ring. This feature facilitates
the provision of efficient lubrication.
Double row full complement cylindrical roller
bearings of the NNC, NNCL, and NNCF designs
differ only in the number of flanges on the
outer ring. The inner ring with its three integral
flanges between which the two rows of rollers
are accurately guided is common to all three
designs. Outer ring flanges or retaining rings
inserted in the outer ring bore prevent the
bearing from falling apart.
Bearings of the NNCL design (Figure 2c)
have no integral flanges on the outer ring. Axial
displacements of the shaft relative to the housing are thus permitted, within certain limits.
Bearings of the NNCF and NNC designs
(Figure 2d and 2e) have one integral flange
and a retaining ring in the outer ring. They can
accommodate axial loads in one direction and
can locate the shaft in one direction. Axial displacements of the shaft relative to the housing
are permitted.
The rollers of bearings of the NNF design
(series NNF 50) are guided between the
integral flanges of the two-part inner ring,
which is held together by a retaining ring. The
outer ring has a central integral flange. The
bearings can be used as locating bearings as
they can accommodate axial loads acting in
both directions. Because of the large distance
between the roller rows, they are also suitable
for the accommodation of tilting moments.
The outer ring of the bearing is 1 mm
narrower than the inner ring and has two snap
ring grooves in the outside diameter. It is thus
possible to dispense with spacer rings between
the inner ring and adjacent components without affecting outer ring rotation; for example
in pulleys, or the housing (or hub) can be
made narrower than the bearing and axial
space saved.
Figure 2
116
NCF
NJG
NNCL
NNCF
NNC
NNF
Introduction
Internal clearance
Cylindrical roller bearings of the NUP type

can serve to locate shafts in both directions, and
are manufactured by SKF with axial internal
clearance according to Table 2.
The values given in Table 2 for axial internal
clearance should be considered as guideline
values. Because of roller tilting during measurement of the axial internal clearance, increases in
the clearance are possible. These correspond:
For bearings of series 10, 2, 3 and 4 to
approximately the radial internal
clearance, and
For bearings of series 22 and 23 to
approximately 2/3 of the radial internal
clearance

SKF single row cylindrical roller bearings are
produced with Normal radial internal clearance
as standard; the majority of the bearings are
also available with C3 radial internal clearance
and some with the appreciably greater
C4 clearance.
The values for the clearance correspond to
DIN 620, Part 4 for the size range covered by
this standard and are given in Table 1. The
values apply to bearings before mounting and
under zero measuring load.
SKF full complement cylindrical roller bearings
are manufactured with Normal or C3 radial
internal clearance as standard. The values for
the clearance limits correspond to ISO and are
shown in Table 1.
Special solutions
using cylindrical
roller bearings
SKF also manufactures:
Precision single and double row
cylindrical roller bearings for machine tool
applications
Double and multi-row cylindrical roller
bearings for rolling mill and other heavy
engineering applications
Special traction roller bearings for railroad
applications
Details on these special solution products are
available in other SKF publications, which can be
supplied upon request
Table 1
Radial internal clearance of cylindrical roller bearings
Bore
diameter
d
over incl.
mm

C2
min
m
max
min
in
max
Normal
min max
m
min
in
max
C3
min
m
max
min
in
max
C4
min
m
max
min
in
max
24
30
24
30
40
0
0
5
25
25
30
0.0000
0.0000
0.0002
0.0010
0.0010
0.0012
20
20
25
45
45
50
0.0008
0.0008
0.0010
0.0018
0.0018
0.0020
35
35
45
60
60
70
0.0014
0.0014
0.0018
0.0024
0.0024
0.0028
50
50
60
75
75
85
0.0020
0.0020
0.0024
0.0030
0.0030
0.0033
40
50
65
50
65
80
5
10
10
35
40
45
0.0002
0.0004
0.0004
0.0014
0.0016
0.0018
30
40
40
60
70
75
0.0012
0.0016
0.0016
0.0024
0.0028
0.0030
50
60
65
80
90
100
0.0020
0.0024
0.0026
0.0031
0.0035
0.0039
70
80
90
100
110
125
0.0028
0.0031
0.0035
0.0039
0.0043
0.0049
80
100
120
100
120
140
15
15
15
50
55
60
0.0006
0.0006
0.0006
0.0020
0.0022
0.0024
50
50
60
85
90
105
0.0020
0.0020
0.0024
0.0033
0.0035
0.0041
75
85
100
110
125
145
0.0030
0.0033
0.0039
0.0043
0.0049
0.0057
105
125
145
140
165
190
0.0041
0.0049
0.0057
0.0055
0.0065
0.0075
140
160
180
160
180
200
20
25
35
70
75
90
0.0008
0.0010
0.0014
0.0028
0.0030
0.0035
70
75
90
120
125
145
0.0028
0.0003
0.0035
0.0047
0.0049
0.0057
115
120
140
165
170
195
0.0045
0.0047
0.0055
0.0065
0.0067
0.0077
165
170
195
215
220
250
0.0065
0.0067
0.0077
0.0085
0.0087
0.0098
200
225
250
225
250
280
45
45
55
105
110
125
0.0018
0.0018
0.0022
0.0041
0.0043
0.0049
105
110
125
165
175
195
0.0041
0.0043
0.0049
0.0065
0.0069
0.0077
160
170
190
220
235
260
0.0063
0.0067
0.0075
0.0087
0.0093
0.0102
220
235
260
280
300
330
0.0087
0.0093
0.0102
0.0110
0.0118
0.0130
280
315
355
315
355
400
55
65
100
130
145
190
0.0022
0.0026
0.0039
0.0051
0.0057
0.0075
130
145
190
205
225
280
0.0051
0.0057
0.0075
0.0081
0.0089
0.0110
200
225
280
275
305
370
0.0079
0.0089
0.0110
0.0108
0.0120
0.0146
275
305
370
350
385
460
0.0108
0.0120
0.0146
0.0138
0.0152
0.0181
400
450
500
450
500
560
110
110
120
210
220
240
0.0043
0.0043
0.0047
0.0083
0.0087
0.0094
210
220
240
310
330
360
0.0083
0.0087
0.0094
0.0122
0.0130
0.0142
310
330
360
410
440
480
0.0122
0.0130
0.0142
0.0161
0.0173
0.0189
410
440
480
510
550
600
0.0161
0.0173
0.0189
0.0201
0.0217
0.0236
560
630
710
630
710
800
140
145
150
260
285
310
0.0055
0.0057
0.0059
0.0102
0.0112
0.0122
260
285
310
380
425
470
0.0102
0.0112
0.0122
0.0150
0.0167
0.0185
380
425
470
500
565
630
0.0150
0.0167
0.0185
0.0197
0.0222
0.0248
500
565
630
620
705
790
0.0197
0.0222
0.0248
0.0244
0.0278
0.0311
117

Introduction
Loads

for full complement cylindrical
roller bearings
P = 0.92 Fr + YFa when Fa / Fr > e

single row cylindrical roller bearings
where
e = calculation factor
= 0.2 for bearings of
Y = axial load factor
When cylindrical roller bearings are used as

non-locating bearings and are only subjected to
radial loads, the equivalent dynamic bearing
load is
P = Fr
series 10, 2, 3 and 4

series 22 and 23
When cylindrical roller bearings are used as

non-locating bearings and are only subjected
to radial loads, the equivalent dynamic
bearing load
series 10, 2, 3 and 4

series 22 and 23
P = Fr
If cylindrical roller bearings with flanges
on inner and outer rings are used to axially
locate the shaft in one or both directions, as is
frequently the case, the equivalent dynamic
bearing load should be calculated using
Since axially loaded cylindrical roller bearings

will only operate satisfactorily when they are
subjected to a simultaneously acting radial load,
the ratio Fa / Fr should not exceed 0.5 for EC
design bearings and 0.4 for the other bearings.
If cylindrical roller bearings with flanges on

inner and outer rings are used to axially locate
the shaft in one or both directions, as is
frequently the case, the equivalent dynamic
bearing load should be calculated using
Table 2
Axial internal clearance of single row cylindrical roller bearings
Bore
diameter
d
mm
NUP 2
min max min
m
in
15
17
20
37
37
140
140
0.0015 0.0055
0.0015 0.0000
37
37
140
140
0.0015
0.0015
0.0055
0.0055
25
30
35
37
37
47
140
140
155
0.0015 0.0055
0.0015 0.0055
0.0019 0.0061
47
47
47
155
155
155
0.0019
0.0019
0.0019
0.0061
0.0061
0.0061
55
155
0.0022 0.0061
47
47
47
155
155
155
0.0019 0.0061
0.0019 0.0061
0.0019 0.0061
47
47
62
155
155
180
0.0019 0.0061
0.0019 0.0061
0.0024 0.0071
40
45
50
47
47
47
155
155
155
0.0019 0.0061
0.0019 0.0061
0.0019 0.0061
47
47
47
155
155
155
0.0019
0.0019
0.0019
0.0061
0.0061
0.0061
55
55
70
155
155
185
0.0022 0.0061
0.0022 0.0061
0.0028 0.0073
47
47
47
155
155
155
0.0019 0.0061
0.0019 0.0061
0.0019 0.0061
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
55
60
65
47
47
47
155
155
155
0.0019 0.0061
0.0019 0.0061
0.0019 0.0061
47
62
62
155
180
180
0.0019
0.0024
0.0024
0.0061
0.0071
0.0071
70
70
70
185
185
185
0.0028 0.0073
0.0028 0.0073
0.0028 0.0073
47
62
62
155
180
180
0.0019 0.0061
0.0024 0.0071
0.0024 0.0071
62
87
87
180
230
230
0.0024 0.0071
0.0034 0.0091
0.0034 0.0091
70
75
80
47
47
47
155
155
155
0.0019 0.0061
0.0019 0.0061
0.0019 0.0061
62
62
62
180
180
180
0.0024
0.0024
0.0024
0.0071
0.0071
0.0071
70
70
-
185
185
-
0.0028 0.0073
0.0028 0.0073
-
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
87
87
87
230
230
230
0.0034 0.0091
0.0034 0.0091
0.0034 0.0091
85
90
95
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
62
62
62
180
180
180
0.0024
0.0024
0.0024
0.0071
0.0071
0.0071
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
87
87
87
230
230
230
0.0034 0.0091
0.0034 0.0091
0.0034 0.0091
100
105
110
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
87
87
230
230
0.0034
0.0034
0.0091
0.0091
87
87
87
230
230
230
0.0034 0.0091
0.0034 0.0091
0.0034 0.0091
120 315
120 315
120 315
0.0047 0.0124
0.0047 0.0124
0.0047 0.0124
120
130
140
62
62
62
180
180
180
0.0024 0.0071
0.0024 0.0071
0.0024 0.0071
87
87
87
230
230
230
0.0034
0.0034
0.0034
0.0091
0.0091
0.0091
87
87
87
230
230
230
0.0034 0.0091
0.0034 0.0091
0.0034 0.0091
120 315
120 315
120 315
0.0047 0.0124
0.0047 0.0124
0.0047 0.0124
150
160
170
62
87
87
180
230
230
0.0024 0.0071
0.0034 0.0091
0.0034 0.0091
87
-
230
-
0.0034
-
0.0091
-
87
-
230
-
0.0034 0.0091
-
120 315
-
0.0047 0.0124
-
180
190
200
87
87
87
230
230
230
0.0034 0.0091
0.0034 0.0091
0.0034 0.0091
220
95
230
0.0037 0.0091
118
max
NUP 3
min max min
m
in
max
NUP 4
min max
m
min
in
max
NUP 22
min max
m
min
in
NUP 23
min max
m
min
in
37
47
140
155
0.0015 0.0055
0.0019 0.0061
47
47
155
155
0.0019 0.0061
0.0019 0.0061
max
max
Introduction
P = 0.92 Fr + YFa when Fa / Fr > e
Since axially loaded full complement

cylindrical roller bearings will only operate
satisfactorily when they are subjected to a
simultaneously acting radial load, the ratio
Fa / Fr should not exceed 0.5 for single row
bearings or 0.25 for double row bearings.
Y = axial load factor

= 0.6 for bearings of series 18
= 0.53 for double row bearings
= 0.4 for all other single row bearings
where
= 0.15 for double row bearings
= 0.2 for bearings of series 18
= 0.3 for all other single row bearings
Table 3a
Axial displacement(s) of NU, NJ and N bearing ring relative to opposite ring
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
1005
1006
1007 EC
2
2.1
1
0.079
0.083
0.039
208 EC
209 EC
210 EC
1.4
1.2
1.5
0.055
0.047
0.059
2222 EC
2224 EC
2226 EC
3.7
3.8
4.3
0.146
0.150
0.169
302 EC
303 EC
304 EC
1
1
0.9
0.039
0.039
0.035
1008
1009 EC
1010
2.4
0.9
2.5
0.094
0.035
0.098
211 EC
212 EC
213 EC
1
1.4
1.4
0.039
0.055
0.055
2228 EC
2230 EC
2232 EC
4.4
4.9
4.5
0.173
0.193
0.177
305 EC
306 EC
307 EC
1.3
1.4
1.2
0.051
0.055
0.047
1011 EC
1012
1013
0.5
2.9
2.9
0.020
0.114
0.114
214 EC
215 EC
216 EC
1.2
1.2
1.4
0.047
0.047
0.055
2234 EC
2236 EC
2238 EC
4.2
4.2
5
0.165
0.165
0.197
308 EC
309 EC
310 EC
1.4
1.7
1.9
0.055
0.067
0.075
1014
1015
1016
3
3
3.3
0.118
0.118
0.130
217 EC
218 EC
219 EC
1.5
1.8
1.7
0.059
0.071
0.067
2240 EC
2244 EC
2248
5.1
7.9
4.3
0.201
0.311
0.169
311 EC
312 EC
313 EC
2
2.1
2.2
0.079
0.083
0.087
1017
1018
1019
3.3
3.5
3.5
0.130
0.138
0.138
220 EC
221 EC
222 EC
1.7
2
2.1
0.067
0.079
0.083
2252
2256 EC
2260
4.3
10.2
5.6
0.169
0.402
0.220
314 EC
315 EC
316 EC
1.8
1.8
2.1
0.071
0.071
0.083
1020
1021
1022
3.5
3.8
3.8
0.138
0.150
0.150
224 EC
226 EC
228 EC
1.9
2.1
2.4
0.075
0.083
0.094
2264
2268
2272
5.9
8
16.7
0.232
0.315
0.657
317 EC
318 EC
319 EC
2.3
2.5
2.9
0.091
0.098
0.114
1024
1026
1028
3.8
4.7
4.4
0.150
0.185
0.173
N 228
230 EC
232 EC
2.5
2.5
2.7
0.098
0.098
0.106
2276
8.3
0.327
320 EC
321 EC
322 EC
2.9
3.4
3
0.114
0.134
0.118
1030
1032
1034
4.9
5.2
5.8
0.193
0.205
0.228
234 EC
236 EC
238 EC
2.9
2.9
3
0.114
0.114
0.118
2304 EC
2305 EC
2306 EC
1.9
2.3
2.4
0.075
0.091
0.094
324 EC
326 EC
328 EC
3.7
3.7
3.7
0.146
0.146
0.146
1038
1040
1044
6.1
7
7.5
0.240
0.276
0.295
240 EC
244
248
2.6
2.3
3.4
0.102
0.091
0.134
2307 EC
2308 EC
2309 EC
2.7
2.9
3.2
0.106
0.114
0.126
N 328
330 EC
332 EC
4.2
4
4
0.165
0.157
0.157
1048
1052
1056
7.5
8.8
8.8
0.295
0.346
0.346
252
256
260
3.4
3.8
4.8
0.134
0.150
0.189
2310 EC
2311 EC
2312 EC
3.4
3.5
3.6
0.134
0.138
0.142
334
336
338 EC
4.6
4.4
4.3
0.181
0.173
0.169
1060
1064
1068
6
13.5
6.5
0.382
0.382
0.425
264
5.3
0.209
2313 EC
2314 EC
2315 EC
4.7
4.8
4.8
0.185
0.189
0.189
0.425
0.425
0.551
0.059
0.079
0.071
0.157
0.205
0.220
6.5
6.5
7
1.5
2
1.8
4
5.2
5.6
1072
1076
1080
2203 EC
2204 EC
2205 EC
340
344
348
2316 EC
2317 EC
2318 EC
5.1
5.8
6
0.201
0.228
0.382
1084
1088
1092
11
7
7.8
0.551
0.579
0.626
2206 EC
2207 EC
2208 EC
1.8
2.8
1.9
0.071
0.110
0.075
2319 EC
2320 EC
2322 EC
6.9
5.9
7.5
0.272
0.232
0.295
406
407
408
1.6
1.7
2.5
0.063
0.067
0.098
1096
10/500
10/530
7.8
11.2
10.4
0.626
0.441
0.409
2209 EC
2210 EC
2211 EC
1.7
1.5
1.5
0.067
0.059
0.059
2324 EC
2326 EC
2328 EC
7.2
8.7
9.7
0.283
0.343
0.382
409
410
411
2.5
2.6
2.6
0.098
0.102
0.102
10/560
10/600
10/710 EC
10
8.5
8
0.484
0.547
0.673
2212 EC
2213 EC
2214 EC
1.4
1.9
1.7
0.055
0.075
0.067
2330 EC
2332 EC
2334
10.5
11
5.2
0.413
0.433
0.205
412
413
414
2.5
2.6
3.5
0.098
0.102
0.138
2215 EC
2216 EC
2217 EC
1.7
1.4
2
0.067
0.055
0.079
2336
2338 EC
2340 EC
5.1
9.5
9.4
0.201
0.374
0.370
415
416
417
3.8
3.7
3.8
0.150
0.146
0.150
2218 EC
2219 EC
2220 EC
2.6
3
2.5
0.102
0.118
0.098
2344 EC
2348
2356
10.4
6.4
6.6
0.409
0.252
0.260
418
419
420
4.9
5
4.9
0.193
0.197
0.193
421
422
424
4.9
4.8
6.3
0.193
0.189
0.248
202 EC
203 EC
204 EC
1
1
1
0.039
0.039
0.039
205 EC
206 EC
207 EC
1.3
1.3
1.3
0.051
0.051
0.051
119
Minimum load
In order to provide the satisfactory operation
of all ball and roller bearings they must
always be subjected to a given minimum
load. This is also true of cylindrical roller bearings, particularly if they run at high speeds
where the inertia forces of the rollers and cage,
and the friction in the lubricant can have a
detrimental influence on the rolling conditions
in the bearing and may cause damaging sliding
the raceways.


bearing, for example, by increasing belt tension
or similar means.
Table 3b
Axial displacement(s) of full complement NCF and NJG bearing ring relative to opposite ring
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
1830 V
1832 V
1834 V
1.5
1.5
1.5
0.059
0.059
0.059
2305 VH
2306 VH
2307 VH
1.7
1.8
2
0.067
0.071
0.079
2944 V
2948 V
2952 V
2.5
2.5
5
0.098
0.098
0.197
3020 V
3022 V
3024 V
2
3
3.5
0.079
0.118
0.138
1836
1838
1840
1844
V
V
V
V
1.5
1.8
1.8
1.8
0.059
0.071
0.071
0.071
2308 VH
2309 VH
2310 VH
2.4
2.4
2.6
0.094
0.094
0.102
2956 V
2960 V
2964 V
4
5
5
0.157
0.197
0.197
3026 V
3028 V
3030 V
3.5
3.5
3.5
0.138
0.138
0.138
1848 V
1852 V
1856 V
1.8
1.8
2.5
0.071
0.071
0.098
2311 VH
2313 VH
2314 VH
2.6
3
3
0.102
0.118
0.118
2968 V
2972 V
2976 V
5
5
5
0.197
0.197
0.197
3032 V
3034 V
3036 V
4
7
5
0.157
0.276
0.197
1860 V
1864 V
1868 V
3
3
3
0.118
0.118
0.118
2315 VH
2316 VH
2317 VH
3
4
4
0.118
0.157
0.157
2980 V
2984 V
2988 V
5
5
6
0.197
0.197
0.236
3038 V
3040 V
3044 V
6
6.5
7
0.236
0.256
0.276
1872 V
1876 V
1880 V
3
3.5
3.5
0.118
0.138
0.138
2318 VH
2320 VH
2322 VH
4
4.5
5
0.157
0.177
0.197
2992 V
2996 V
29/500 V
6
7
7
0.236
0.276
0.276
3048 V
3052 V
3056 V
7
8
9
0.276
0.315
0.354
1884 V
1888 V
1892 V
3.5
3.5
5
0.138
0.138
0.197
2324 VH
2326 VH
2328 VH
5.5
6
6.5
0.217
0.236
0.256
29/530 V
29/560 V
29/600 V
7
7
7
0.276
0.276
0.276
3060 V
3064 V
3068 V
10
12
12
0.394
0.472
0.472
2330 VH
6.5
0.256
1896 V
18/500 V
18/530 V
5
5
5
0.197
0.197
0.197
3072 V
3076 V
3080 V
12
12
14
0.472
0.472
0.551
18/560 V
18/600 V
18/630 V
5
7
8
0.197
0.276
0.315
2912 V
2914 V
2916 V
0.5
0.75
0.75
0.020
0.030
0.030
18/670 V
18/710 V
18/750 V
8
8
8
0.315
0.315
0.315
2918 V
2920 V
2922 V
0.75
0.75
0.75
0.030
0.030
0.030
2924 V
2926 V
2928 V
0.75
0.75
0.75
0.030
0.030
0.030
2207 V
2209 V
2210 V
1
1
1
0.039
0.039
0.039
2930 V
2932 V
2934 V
0.8
0.8
0.8
0.031
0.031
0.031
2218 V
2220 V
2224 V
2.5
2.5
4
0.098
0.098
0.157
2936 V
2938 V
2940 V
1
1
3
0.039
0.039
0.118
120
3004 V
3005 V
3006 V
0.5
0.5
0.8
0.020
0.020
0.031
3007 V
3008 V
3009 V
1
1
1
0.039
0.039
0.039
3010 V
3011 V
3012 V
1
1.2
1.2
0.039
0.047
0.047
3013 V
3014 V
3015 V
1.2
1.5
1.5
0.047
0.059
0.059
3016 V
3017 V
3018 V
1.8
1.8
2
0.071
0.071
0.079

Table 3c
Axial displacement (s) of full complement NNC, NNCF and NNCL bearing ring relative to opposite ring
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
Designation
Axial displacement
s
mm
in
4830 V
4832 V
4834 V
1.1
1.1
1.1
0.043
0.043
0.043
4912 V
4914 V
4916 V
1
1
1
0.039
0.039
0.039
4940 V
4944 V
4948 V
2.1
2.1
2.1
0.083
0.083
0.083
5013 V
5015 V
5017 V
1.1
1.1
1.1
0.043
0.043
0.043
4836 V
4838 V
4840 V
1.1
1.5
1.5
0.043
0.059
0.059
4918 V
4920 V
4922 V
1.1
1.1
1.1
0.043
0.043
0.043
4952 V
4956 V
4960 V
2.1
2.1
3
0.083
0.083
0.118
5024 V
5056 V
2
4
0.079
0.157
4844 V
4848 V
4852 V
1.5
2
2
0.059
0.079
0.079
4924 V
4926 V
4926 V
1.1
1.5
1.5
0.043
0.059
0.059
4964 V
4968 V
4972 V
3
3
3
0.118
0.118
0.118
4856 V
4860 V
4864 V
2
2.1
2.1
0.079
0.083
0.083
4928 V
4930 V
4932 V
1.5
2
2
0.059
0.079
0.079
4976 V
4980 V
4984 V
4
4
4
0.157
0.157
0.157
4872 V
4876 V
2.1
2.1
0.083
0.083
4934 V
4936 V
4938 V
2
2
2
0.079
0.079
0.079
4988 V
4992 V
4996 V
4
4
5
0.157
0.157
0.197
49/500 V
0.197
121

Single row
Standard
Series: 1005 1052
Size: 25 mm 260 mm
0.9843 in 10.2362 in
Type NUP
Type NJ
Type NU
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
Diameter
lb
Under roller
F
mm
in
1005
1006
1007 EC
25
30
35
0.9843
1.1811
1.3780
47
55
62
1.8504
2.1654
2.4409
12
13
14
0.4724
0.5118
0.5512
14 200
17 900
35 800
3 190
4 020
8 050
13 200
17 300
38 000
2 970
3 890
8 540
18 000
15 000
12 000
18 000
15 000
13 000
0.08
0.12
0.16
0.18
0.26
0.35
31
37
42
1.201
1.437
1.654
1008 ML
1009 EC
1010
40
45
50
1.5748
1.7717
1.9685
68
75
80
2.6772
2.9528
3.1496
15
16
16
0.5906
0.6299
0.6299
25 100
44 600
46 800
5 640
10 000
10 500
26 000
52 000
56 000
5 840
11 700
12 600
12 000
9 500
9 000
18 000
11 000
9 500
0.22
0.27
0.35
0.49
0.60
0.77
47
53
58
1.850
2.067
2.264
1011 EC
1012 ML
1013
55
60
65
2.1654
2.3622
2.5591
90
95
100
3.5433
3.7402
3.9370
18
18
18
0.7087
0.7087
0.7087
57 200
37 400
62 700
12 900
8 400
14 100
69 500
44 000
81 500
15 600
9 900
18 300
8 000
8 000
7 000
8 500
13 000
7 500
0.42
0.48
0.45
0.90
1.10
1.00
65
70
75
2.539
2.736
2.933
1014
1015 ML
1016
70
75
80
2.7559
2.9528
3.1496
110
115
125
4.3307
4.5276
4.9213
20
20
22
0.7874
0.7874
0.8661
76 500
58 300
66 000
17 200
13 100
14 800
93 000
71 000
81 400
20 900
16 000
18 300
6 300
6 700
6 300
7 000
10 000
6 300
0.62
0.74
1.00
1.40
1.60
2.20
80
85
92
3.150
3.346
3.602
1017
1018 ML
1019 ML
85
90
95
3.3465
3.5433
3.7402
130
140
145
5.1181
5.5118
5.7087
22
24
24
0.8661
0.9449
0.9449
68 200
80 900
84 200
15 300
18 200
18 900
86 500
104 000
110 000
19 400
23 400
24 700
6 000
5 600
5 300
6 000
8 500
8 000
1.05
1.35
1.40
2.30
3.00
3.10
97
103
108
3.799
4.055
4.252
1020
1021 ML
1022
100
105
110
3.9370
4.1339
4.3307
150
160
170
5.9055
6.2992
6.6929
24
26
28
0.9449
1.0236
1.1024
85 800
101 000
128 000
19 300
22 700
28 800
114 000
137 000
166 000
25 600
30 800
37 300
5 000
4 800
4 500
5 000
7 500
4 500
1.45
1.85
2.30
3.20
4.10
5.10
113
120
125
4.449
4.705
4.921
1024
1026
1028
120
130
140
4.7244
5.1181
5.5118
180
200
210
7.0866
7.8740
8.2677
28
33
33
1.1024
1.2992
1.2992
134 000
165 000
172 000
30 100
37 100
38 700
183 000
224 000
245 000
41 100
50 400
55 100
4 000
3 800
3 600
4 000
3 800
3 600
2.45
3.80
4.05
5.40
8.40
8.90
135
148
158
5.315
5.827
6.220
1030
1032
1034
150
160
170
5.9055
6.2992
6.6929
225 8.8583
240 9.4488
260 10.2362
35
38
42
1.3780
1.4961
1.6535
194 000
229 000
275 000
43 600
51 500
61 800
275 000
325 000
400 000
61 800
73 100
89 900
3 200
3 000
2 800
3 200
3 000
2 800
4.85
5.95
8.00
10.70
13.10
17.60
170
180
193
6.673
7.087
7.598
1036
1038 ML
1040
180
190
200
7.0866
7.4803
7.8740
280 11.0236
290 11.4173
310 12.2047
46
46
51
1.8110
1.8110
2.0079
336 000
347 000
380 000
75 500
78 000
85 400
475 000
500 000
570 000
106 800
112 400
128 100
2 600
2 600
2 400
2 600
3 800
2 400
10.50
11.00
14.50
23.10
24.30
32.00
205
215
229
8.071
8.465
9.016
1044
1048 MA
1052
220
240
260
8.6614
9.4488
10.2362
340 13.3858
360 14.1732
400 15.7480
56
56
65
2.2047
2.2047
2.5591
495 000
523 000
627 000
111 300
117 600
140 900
735 000
800 000
965 000
165 200
179 800
216 900
2 200
2 000
1 800
2 200
2 600
1 800
18.50
20.00
29.50
40.80
44.10
65.00
250
270
296
9.843
10.630
11.654
122
Single row
Standard
Series: 1056 MA 10/710 ECN2MA
Size: 280 mm 710 mm
11.0236 in 27.9528 in
Type NUP
Type NJ
Type NU
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
Diameter
lb
Under roller
F
mm
in
1056 MA
1060 MA
1064 MA
280 11.0236
300 11.8110
320 12.5984
420 16.5354
460 18.1102
480 18.8976
65
74
74
2.5591
2.9134
2.9134
660 000
858 000
880 000
148 400
192 900
197 800
1 060 000
1 370 000
1 430 000
238 300
308 000
321 500
1 700
1 500
1 400
2 200
2 000
1 400
31.50
46.50
49.00
69.40
102.50
108.00
316
340
360
12.441
13.386
14.173
1064 MP
1068 MA
1072 MA
320 12.5984
340 13.3858
360 14.1732
480 18.8976
520 20.4724
540 21.2598
74
82
82
2.9134
3.2283
3.2283
880 000
1 080 000
1 100 000
197 800
242 800
247 300
1 430 000
1 760 000
1 830 000
321 500
395 600
411 400
1 400
1 300
1 300
2 200
1 700
1 600
48.50
68.00
67.50
106.90
149.90
148.80
360
385
405
14.173
15.157
15.945
1072 MP
1076 MA
1080 MA
360 14.1732
380 14.9606
400 15.7480
540 21.2598
560 22.0472
600 23.6220
82
82
90
3.2283
3.2283
3.5433
1 100 000
1 140 000
1 380 000
247 300
256 300
310 200
1 830 000
1 930 000
2 320 000
411 400
433 900
521 500
1 300
1 200
1 100
1 900
1 600
1 500
67.50
73.00
92.50
148.80
160.90
203.90
405
425
450
15.945
16.732
17.717
1084 MA
1088 MA
1092 MA
420 16.5354
440 17.3228
460 18.1102
620 24.4094
650 25.5906
680 26.7717
90
94
100
3.5433
3.7008
3.9370
1 420 000
1 510 000
1 650 000
319 200
339 400
370 900
2 450 000
2 650 000
2 850 000
550 800
595 700
640 700
1 100
1 000
950
1 400
1 300
1 200
96.00
105.00
115.00
211.60
231.50
253.50
470
493
516
18.504
19.409
20.315
1096 MA
10/500 MA
10/530 MA
480 18.8976
500 19.6850
530 20.8661
700 27.5591
720 28.3465
780 30.7087
100
100
112
3.9370
3.9370
4.4094
1 680 000
1 720 000
2 290 000
377 700
386 700
514 800
3 000 000
3 100 000
4 050 000
674 400
696 900
910 400
900
900
800
1 200
1 100
1 000
130.00
135.00
190.00
286.60
297.60
418.90
536
556
593
21.102
21.890
23.346
10/560 MA
560 22.0472
820 32.2835
10/600 MA
600 23.6220
870 34.2520
10/710 ECN2MA 710 27.9528 1 030 40.5512
115
118
140
4.5276
4.6457
5.5118
2 330 000
523 800
2 750 000
618 200
4 680 000 1 052 100
4 250 000
5 100 000
8 500 000
955 400
1 146 500
1 910 800
750
700
560
1 000
900
750
210.00
245.00
415.00
463.00
540.10
914.90
625
667
778
24.606
26.260
30.630
123

Single row
Series: 202 EC 240 EC
Size: 15 mm 200 mm
0.5906 in 7.8740 in
Type NUP
Type NU
Designation
Bore
d
mm
in
Type NJ
Basic load ratings
Outside diameter Width

D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Mass
Diameter
lbf
Reference Limiting
speed speed
r/min r/min
kg
lb
Under roller
F
mm
in
Static
C0
N
Type N
Over roller
E
mm
in
202 EC
203 EC
204 EC
15
17
20
0.5906
0.6693
0.7874
35
40
47
1.3780
1.5748
1.8504
11
12
14
0.4331
0.4724
0.5512
12 500
17 200
25 100
2 800
3 900
5 600
10 200
14 300
22 000
2 300
3 200
4 900
22 000 26 000
19 000 22 000
16 000 19 000
0.05
0.07
0.11
0.10
0.10
0.20
19.30
22.10
26.50
0.76
0.87
1.04
30
35
42
1.181
1.382
1.634
205 EC
206 EC
207 EC
25
30
35
0.9843
1.1811
1.3780
52
62
72
2.0472
2.4409
2.8346
15
16
17
0.5906
0.6299
0.6693
28 600
44 000
56 000
6 400
9 900
12 600
27 000
36 500
48 000
6 100
8 200
10 800
14 000 16 000
13 000 14 000
11 000 12 000
0.13
0.20
0.33
0.30
0.40
0.70
31.50
37.50
44.00
1.24
1.48
1.73
47
56
64
1.831
2.185
2.520
208 EC
209 EC
210 EC
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1496
3.3465
3.5433
18
19
20
0.7087
0.7480
0.7874
62 000
69 500
73 500
13 900
15 600
16 500
53 000
64 000
69 500
11 900
14 400
15 600
9 500 11 000
9 000 9 500
8 500 9 000
0.37
0.43
0.48
0.80
0.90
1.10
49.50
54.50
59.50
1.95
2.15
2.34
72
77
82
2.815
3.012
3.209
211 EC
212 EC
213 EC
55
60
65
2.1654
2.3622
2.5591
100
110
120
3.9370
4.3307
4.7244
21
22
23
0.8268
0.8661
0.9055
96 500
108 000
122 000
21 700
24 300
27 400
95 000
102 000
118 000
21 400
22 900
26 500
7 500
6 700
6 300
8 000
7 500
6 700
0.66
0.81
1.05
1.50
1.80
2.30
66.00
72.00
78.50
2.60
2.84
3.09
90
100
109
3.543
3.937
4.272
214 EC
215 EC
216 EC
70
75
80
2.7559
2.9528
3.1496
125
130
140
4.9213
5.1181
5.5118
24
25
26
0.9449
0.9843
1.0236
137 000
150 000
160 000
30 800
33 700
36 000
137 000
156 000
166 000
30 800
35 100
37 300
6 000
5 600
5 300
6 300
6 000
5 600
1.15
1.25
1.50
2.50
2.80
3.30
83.50
88.50
95.30
3.29
3.48
3.75
114
119
127
4.469
4.665
5.012
217 EC
218 EC
219 EC
85
90
95
3.3465
3.5433
3.7402
150
160
170
5.9055
6.2992
6.6929
28
30
32
1.1024
1.1811
1.2598
190 000
208 000
255 000
42 700
46 800
57 300
200 000
220 000
265 000
45 000
49 500
59 600
4 800
4 500
4 300
5 300
5 000
4 800
1.90
2.35
2.85
4.20 100.50
5.20 107.00
6.30 112.50
3.96
4.21
4.43
137
145
155
5.374
5.709
6.083
220 EC
221 EC
222 EC
100
105
110
3.9370
4.1339
4.3307
180
190
200
7.0866
7.4803
7.8740
34
36
38
1.3386
1.4173
1.4961
285 000
300 000
335 000
64 100
67 400
75 300
305 000
315 000
365 000
68 600
70 800
82 100
4 000
3 800
3 600
4 500
4 300
4 000
3.45 7.60 119.00

3.95 8.70 125.00
5.40 11.90 132.50
4.69
4.92
5.22
163
173
181
6.417
6.811
7.106
224 EC
226 EC
228 EC
120
130
140
4.7244
5.1181
5.5118
215
230
250
8.4646
9.0551
9.8425
40
40
42
1.5748
1.5748
1.6535
390 000
87 700
415 000
93 300
450 000 101 200
430 000
455 000
510 000
96 700
102 300
114 600
3 400
3 200
2 800
3 600
3 400
3 200
6.60 14.60 143.50

6.30 13.90 153.50
8.75 19.30 169.00
5.65
6.04
6.65
196
210
221
7.697
8.248
8.701
230 EC
232 EC
234 EC
150
160
170
5.9055
6.2992
6.6929
270 10.6299
290 11.4173
310 12.2047
45
48
52
1.7717
1.8898
2.0472
510 000 114 600

585 000 131 500
695 000 156 200
600 000
680 000
815 000
134 900
152 900
183 200
2 600
2 400
2 400
2 800
2 600
2 400
10.80 23.80 182.00

14.30 31.50 195.00
18.70 41.20 207.00
7.17
7.68
8.15
242
259
279
9.528
10.197
10.984
236 ECMA
238 EC
240 EC
180
190
200
7.0866
7.4803
7.8740
320 12.5984
340 13.3858
360 14.1732
52
55
58
2.0472
2.1654
2.2835
720 000 161 900

850 000
800 000 179 800
965 000
850 000 191 100 1 020 000
191 100
216 900
229 300
2 200
2 000
1 900
3 200
2 200
2 200
19.30 42.50 217.00

24.50 54.00 230.00
29.00 63.90 243.00
8.54
9.06
9.57
289
306
323
11.378
12.047
12.717
124
Single row
Series: 244 EC 264 MA
Size: 220 mm 320 mm
8.6614 in 12.5984 in
Type NUP

Size: 17 mm 130 mm
0.6693 in 5.1181 in
Type NU
Designation
Type NJ
Type N
Bore
d
mm
in
Basic load ratings

D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
N
lbf
Reference Limiting
speed
speed
r/min r/min
Mass
kg
Diameter
lb
Under roller
F
mm
in
Over roller
E
mm
in
244 EC
248 MA
252 MA
220 8.6614 400 15.7480

240 9.4488 440 17.3228
260 10.2362 480 18.8976
65
72
80
2.5591
2.8346
3.1496
1 060 000
952 000
1 170 000
238 300 1 290 000

214 000 1 370 000
263 000 1 700 000
290 000
308 000
382 200
1 600
1 600
1 400
1 900
2 200
2 000
39.00 86.00
52.50 115.70
70.00 154.30
270.00
295.00
320.00
10.63
11.61
12.60
358
385
420
14.094
15.157
16.535
256 MA
260 M
264 MA
280 11.0236 500 19.6850

300 11.8110 540 21.2598
320 12.5984 580 22.8346
80
85
92
3.1496
3.3465
3.6220
1 140 000
1 420 000
1 610 000
256 300 1 700 000

319 200 2 120 000
361 900 2 450 000
382 200
476 600
550 800
1 400
1 300
1 200
1 900 73.00 160.90

1 400 89.50 197.30
1 600 115.00 253.50
340.00
364.00
390.00
13.39
14.33
15.35
440
476
510
17.323
18.740
20.079
2203 EC
2204 EC
2205 EC
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748
1.8504
2.0472
16
18
18
0.6299
0.7087
0.7087
23 800
29 700
34 100
5 400
6 700
7 700
21 600
27 500
34 000
4 900
6 200
7 600
19 000
16 000
14 000
22 000
19 000
16 000
0.10
0.14
0.18
0.20
0.30
0.40
22.10
26.50
31.50
0.87
1.04
1.24
35
42
47
1.378
1.654
1.850
2206 EC
2207 EC
2208 EC
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409
2.8346
3.1496
20
23
23
0.7874
0.9055
0.9055
55 000
69 500
81 500
12 400
15 600
18 300
49 000
63 000
75 000
11 000
14 200
16 900
13 000
11 000
9 500
14 000
12 000
11 000
0.27
0.40
0.55
0.60
0.90
1.20
37.50
44.00
49.50
1.48
1.73
1.95
56
64
72
2.185
2.520
2.815
2209 EC
2210 EC
2211 EC
45
50
55
1.7717 85
1.9685 90
2.1654 100
3.3465
3.5433
3.9370
23
23
25
0.9055
0.9055
0.9843
85 000
90 000
114 000
19 100
20 200
25 600
81 500
88 000
118 000
18 300
19 800
26 500
9 000
8 500
7 500
9 500
9 000
8 000
0.55
0.61
0.81
1.20
1.30
1.80
54.50
59.50
66.00
2.15
2.34
2.60
77
82
90
3.012
3.228
3.543
2212 EC
2213 EC
2214 EC
60
65
70
2.3622 110
2.5591 120
2.7559 125
4.3307
4.7244
4.9213
28
31
31
1.1024
1.2205
1.2205
146 000
170 000
180 000
32 800
38 200
40 500
153 000
180 000
193 000
34 400
40 500
43 400
6 700
6 300
6 000
7 500
6 700
6 300
1.15
1.45
1.70
2.50
3.20
3.70
72.00
78.50
83.50
2.84
3.09
3.29
100
109
114
4.272
4.488
2215 EC
2216 EC
2217 EC
75
80
85
2.9528 130
3.1496 140
3.3465 150
5.1181
5.5118
5.9055
31
33
36
1.2205
1.2992
1.4173
186 000
212 000
250 000
41 800
47 700
56 200
208 000
245 000
280 000
46 800
55 100
62 900
5 600
5 300
4 800
9 500
5 600
5 300
1.60
2.05
2.55
3.50
4.50
5.60
88.50
95.30
100.50
3.48
3.75
3.96
119
127
137
4.685
5.000
5.394
2218 EC
2219 EC
2220 EC
90
95
100
3.5433 160
3.7402 170
3.9370 180
6.2992
6.6929
7.0866
40
43
46
1.5748
1.6929
1.8110
280 000
325 000
380 000
62 900
73 100
85 400
315 000
375 000
450 000
70 800
84 300
101 200
4 500
4 300
4 000
5 000
4 800
4 500
3.50
3.95
5.20
7.70
8.70
11.50
107.00
112.50
119.00
4.21
4.43
4.69
145
155
163
5.709
6.083
6.417
2222 EC
2224 EC
2226 EC
110
120
130
4.3307 200
4.7244 215
5.1181 230
7.8740
8.4646
9.0551
53
58
64
2.0866
2.2835
2.5197
440 000
520 000
610 000
98 900
116 900
137 100
520 000
630 000
735 000
116 900
141 600
165 200
3 600
3 400
3 200
4 000
3 600
3 400
7.15
8.85
12.20
15.80
19.50
26.90
132.50
143.50
153.50
5.22
5.65
6.04
181
196
210
7.126
7.717
8.268
3.937
125

Single row
Series: 2228 ECML 2292 MA
Size: 140 mm 460 mm
5.5118 in 18.1102 in
Type NUP

Size: 17 mm 70 mm
0.6693 in 2.7559 in
Type NU
Designation
Bore
d
mm
in
Type NJ
Basic load ratings

D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
N
lbf
Reference Limiting
speed
speed
r/min r/min
Type N
Mass
kg
Diameter
lb
Under roller
F
mm
in
Over roller
E
mm
in
2228 ECML
2230 EC
2232 ECMA
140
150
160
5.5118 250 9.8425

5.9055 270 10.6299
6.2992 290 11.4173
68
73
80
2.6772
2.8740
3.1496
655 000
735 000
930 000
147 200 830 000

165 200 930 000
209 100 1 200 000
186 600
209 100
269 800
2 800
2 600
2 400
4 800
2 800
3 400
15.30
18.70
24.70
33.70 169.00
41.20 182.00
54.50 193.00
6.65
7.17
7.60
225
242
261
8.858
9.528
10.276
2234 ECMA
2236 EC
2238 ECMA
170
180
190
6.6929 310 12.2047

7.0866 320 12.5984
7.4803 340 13.3858
86
86
92
3.3858
3.3858
3.6220
1 060 000
1 100 000
1 220 000
238 300 1 430 000

247 300 1 430 000
274 300 1 600 000
321 500
321 500
359 700
2 400
2 200
2 000
3 200
2 400
3 000
30.00
32.00
39.00
66.10 205.00
70.50 215.00
86.00 228.00
8.07
8.47
8.98
281
291
323
11.063
11.457
12.717
2240 ECMA
2248 MA
2252 MA
200 7.8740 360 14.1732 98

240 9.4488 440 17.3228 120
260 10.2362 480 18.8976 130
3.8583
4.7244
5.1181
1 370 000
1 450 000
1 790 000
308 000 1 800 000

326 000 2 360 000
402 400 3 000 000
404 600
530 500
674 400
1 900
1 500
1 300
2 800 46.00
2 200 85.00
2 000 112.00
101.40 241.00 9.49

187.40 295.00 11.61
246.90 320.00 12.60
325
385
420
12.795
15.157
16.535
2256 ECMA
2260 MA
2264 ECMA
280 11.0236 500 19.6850 130

300 11.8110 540 21.2598 140
320 12.5984 580 22.8346 150
5.1181
5.5118
5.9055
2 200 000
2 090 000
3 190 000
494 600 3 250 000

469 800 3 450 000
717 100 5 000 000
730 600
775 600
1 124 000
1 200
1 200
1 000
1 900 115.00
1 800 145.00
1 600 190.00
253.50 327.00 12.87

319.70 364.00 14.33
418.90 390.00 15.35
455
476
530
17.913
18.740
20.866
2268 MA
2272 MA
2276 ECMA
340 13.3858 620 24.4094 165

360 14.1732 650 25.5906 170
380 14.9606 680 26.7717 175
6.4961
6.6929
6.8898
2 640 000
2 920 000
3 140 000
593 500 4 500 000

656 400 4 900 000
705 900 5 500 000
1 011 600
1 101 500
1 236 400
1 000
950
900
1 500 220.00
1 400 250.00
1 400 275.00
485.00 416.00 16.38

551.20 437.00 17.21
606.30 451.00 17.76
544
573
621
21.417
22.559
24.449
2292 MA
460 18.1102 830 32.6772 212
8.3465
5 120 000 1 151 000 8 650 000
1 944 500
700
1 100 530.00 1168.40 554.00 21.81
744
29.291
303 EC
304 EC
305 EC
17
20
25
0.6693
0.7874
0.9843
47
52
62
1.8504
2.0472
2.4409
14
15
17
0.5512
0.5906
0.6693
24 600
35 500
46 500
5 500
8 000
10 500
20 400
26 000
36 500
4 600
5 800
8 200
15 000 20 000
15 000 18 000
12 000 15 000
0.12
0.15
0.24
0.30
0.30
0.50
24.20
27.50
34.00
0.95
1.08
1.34
40
46
54
1.583
1.791
2.126
306 EC
307 EC
308 EC
30
35
40
1.1811
1.3780
1.5748
72
80
90
2.8346
3.1496
3.5433
19
21
23
0.7480
0.8268
0.9055
58 500
75 000
93 000
13 200
16 900
20 900
48 000
63 000
78 000
10 800
14 200
17 500
11 000 12 000
9 500 11 000
8 000 9 500
0.36
0.55
0.64
0.80
1.20
1.40
40.50
46.20
52.00
1.60
1.82
2.05
63
70
80
2.461
2.764
3.150
309 EC
310 EC
311 EC
45
50
55
1.7717 100
1.9685 110
2.1654 120
3.9370
4.3307
4.7244
25
27
29
0.9843
1.0630
1.1417
112 000
127 000
156 000
25 200
28 500
35 100
100 000
112 000
143 000
22 500
25 200
32 100
7 500
6 700
6 000
8 500
8 000
7 000
0.88
1.15
1.57
1.90
2.50
3.50
58.50
65.00
70.50
2.30
2.56
2.78
89
97
107
3.484
3.819
4.193
312 EC
313 EC
314 EC
60
65
70
2.3622 130
2.5591 140
2.7559 150
5.1181
5.5118
5.9055
31
33
35
1.2205
1.2992
1.3780
173 000
212 000
236 000
38 900
47 700
53 100
160 000
196 000
228 000
36 000
44 100
51 300
5 600
5 300
4 800
6 700
6 000
5 600
1.80
2.25
2.75
4.00
5.00
6.10
77.00
82.50
89.00
3.03
3.25
3.50
115
125
133
4.528
4.902
5.236
126
Single row
Series: 315 EC 352 ECMA
Size: 75 mm 260 mm
2.9528 in 10.2362 in
Type NUP
Type NU
Designation
Type NJ
Type N
Bore
d
mm
in
Basic load ratings

D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
N
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Diameter
lb
Under roller
F
mm
in
Over roller
E
mm
in
315 EC
316 EC
317 EC
75
80
85
2.9528 160
3.1496 170
3.3465 180
6.2992
6.6929
7.0866
37
39
41
1.4567
1.5354
1.6142
280 000
300 000
340 000
62 900
67 400
76 400
265 000
290 000
335 000
59 600
65 200
75 300
4 500
4 300
4 000
5 300
5 000
4 800
3.30
3.90
5.10
7.30 95.00
8.60 101.00
11.20 108.00
3.74
3.98
4.25
143
151
160
5.630
5.945
6.299
318 EC
319 EC
320 EC
90
95
100
3.5433 190
3.7402 200
3.9370 215
7.4803
7.8740
8.4646
43
45
47
1.6929
1.7717
1.8504
365 000
390 000
450 000
82 100
87 700
101 200
360 000
390 000
440 000
80 900
87 700
98 900
3 800
3 600
3 200
4 500
4 300
3 800
5.85
6.25
8.85
12.90 113.50
13.80 121.50
19.50 127.50
4.47
4.78
5.02
170
178
192
6.673
6.988
7.539
321 EC
322 EC
324 EC
105
110
120
4.1339 225 8.8583

4.3307 240 9.4488
4.7244 260 10.2362
49
50
55
1.9291
1.9685
2.1654
500 000
530 000
610 000
112 400
119 100
137 100
500 000
540 000
620 000
112 400
121 400
139 400
3 200
3 000
2 800
3 800
3 400
3 200
8.65
11.70
15.00
19.10 133.00
25.80 143.00
33.10 154.00
5.24
5.63
6.06
201
211
230
7.913
8.307
9.055
326 EC
328 EC
330 EC
130
140
150
5.1181 280 11.0236

5.5118 300 11.8110
5.9055 320 12.5984
58
62
65
2.2835
2.4409
2.5591
720 000
780 000
900 000
161 900
175 300
202 300
750 000
830 000
965 000
168 600
186 600
216 900
2 400
2 400
2 200
3 000
2 800
3 400
19.50
23.00
27.70
43.00 167.00
50.70 180.00
61.10 193.00
6.58
7.09
7.60
247
264
283
9.724
10.394
11.142
332 EC
334 EC
336 EC
160
170
180
6.2992 340 13.3858

6.6929 360 14.1732
7.0866 380 14.9606
68
72
75
2.6772 1 000 000

2.8346
952 000
2.9528 1 020 000
224 800 1 080 000

214 000 1 180 000
229 300 1 290 000
242 800
265 300
290 000
2 000
1 700
1 600
2 400
2 200
2 200
32.20
38.50
45.00
71.00 204.00
84.90 220.00
99.20 232.00
8.03
8.66
9.13
300
318
335
11.811
12.520
13.189
338 EC
340 ECMA
340 MA
190
200
200
7.4803 400 15.7480

7.8740 420 16.5354
7.8740 420 16.5354
78
80
80
3.0709 1 140 000

3.1496 1 230 000
3.1496
990 000
256 300 1 500 000

276 500 1 630 000
222 600 1 320 000
337 200
366 400
296 700
1 500
1 400
1 600
200
2 400
2 400
50.00 110.20 245.00 9.65

56.00 123.50 260.00 10.24
56.00 123.50 260.00 10.24
353
370
370
13.898
14.567
14.567
344 M
348 M
352 ECMA
220 8.6614 460 18.1102 88

240 9.4488 500 19.6850 95
260 10.2362 540 21.2598 102
3.4646 1 210 000

3.7402 1 450 000
4.0157 1 940 000
272 000 1 630 000

326 000 2 000 000
436 100 2 700 000
366 400
449 600
607 000
1 500
1 300
1 100
1 700 73.50 162.00 284.00 11.18

1 600 94.50 208.30 310.00 12.21
1 800 125.00 275.60 337.00 13.26
396
430
477
15.591
16.929
18.780
127

Single row
Series: 2304 EC 2356 MA
Size: 20 mm 280 mm
0.7874 in 11.0236 in
Type NUP
Type NU
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
Speed rating
lbf
Reference
speed
r/min
Static
C0
lbf
Type NJ
Limiting
speed
r/min
Mass
kg
Diameter
lb
Under roller
F
mm
in
2304 EC
2305 EC
2306 EC
20
25
30
0.7874
0.9843
1.1811
52
62
72
2.0472
2.4409
2.8346
21
24
27
0.8268
0.9449
1.0630
47 500
64 000
83 000
10 700
14 400
18 700
38 000
55 000
75 000
8 500
12 400
16 900
15 000
12 000
11 000
18 000
15 000
12 000
0.22
0.39
0.54
0.50
0.90
1.20
28
34
41
1.083
1.339
1.594
2307 EC
2308 EC
2309 EC
35
40
45
1.3780 80
1.5748 90
1.7717 100
3.1496
3.5433
3.9370
31
33
36
1.2205
1.2992
1.4173
106 000
129 000
160 000
23 800
29 000
36 000
98 000
120 000
153 000
22 000
27 000
34 400
9 500
8 000
7 500
11 000
9 500
8 500
0.73
0.96
1.35
1.60
2.10
3.00
46
52
59
1.819
2.047
2.303
2310 EC
2311 EC
2312 EC
50
55
60
1.9685 110
2.1654 120
2.3622 130
4.3307
4.7244
5.1181
40
43
46
1.5748
1.6929
1.8110
186 000
232 000
260 000
41 800
52 200
58 400
186 000
232 000
265 000
41 800
52 200
59 600
6 700
6 000
5 600
8 000
7 000
6 700
1.75
2.30
2.80
3.90
5.10
6.20
65
71
77
2.559
2.776
3.031
2313 EC
2314 EC
2315 EC
65
70
75
2.5591 140
2.7559 150
2.9528 160
5.5118
5.9055
6.2992
48
51
55
1.8898
2.0079
2.1654
285 000
315 000
380 000
64 100
70 800
85 400
290 000
325 000
400 000
65 200
73 100
89 900
5 300
4 800
4 500
6 000
5 600
5 300
3.35
4.05
5.00
7.40
8.90
11.00
83
89
95
3.248
3.504
3.740
2316 EC
2317 EC
2318 EC
80
85
90
3.1496 170
3.3465 180
3.5433 190
6.6929
7.0866
7.4803
58
60
64
2.2835
2.3622
2.5197
415 000
455 000
500 000
93 300
102 300
112 400
440 000
490 000
540 000
98 900
110 200
121 400
4 300
4 000
3 800
5 000
4 800
4 500
6.00
7.00
8.15
13.20
15.40
18.00
101
108
114
3.976
4.252
4.469
2319 EC
2320 EC
2322 EC
95
100
110
3.7402 200
3.9370 215
4.3307 240
7.8740
8.4646
9.4488
67
73
80
2.6378
2.8740
3.1496
530 000
670 000
780 000
119 100
150 600
175 300
585 000
735 000
900 000
131 500
165 200
202 300
3 600
3 200
3 000
4 300
3 800
3 400
10.70
13.20
18.90
23.60
29.10
41.70
122
128
143
4.783
5.020
5.630
2324 EC
2326 ECMA
2328 ECMA
120
130
140
4.7244 260 10.2362 86

5.1181 280 11.0236 93
5.5118 300 11.8110 102
3.3858
3.6614
4.0157
915 000
1 060 000
1 200 000
205 700 1 040 000

238 300 1 250 000
269 800 1 430 000
233 800
281 000
321 500
2 800
2 400
2 400
3 200
3 800
3 600
24.30
31.00
37.50
53.60
68.30
82.70
154
167
180
6.063
6.575
7.087
2330 EC
2332 ECMA
2334 ECMA
150
160
170
5.9055 320 12.5984 108

6.2992 340 13.3858 114
6.6929 360 14.1732 120
4.2520
4.4882
4.7244
1 370 000
1 250 000
1 450 000
308 000 1 630 000

281 000 1 730 000
326 000 2 040 000
366 400
388 900
458 600
2 200
2 000
1 700
3 400
3 200
3 000
45.50
53.50
63.00
100.30
117.90
138.90
193
204
220
7.598
8.031
8.661
2336 ECMA
2338 ECMA
2340 ECMA
180
190
200
7.0866 380 14.9606 126

7.4803 400 15.7480 132
7.8740 420 16.5354 138
4.9606
5.1969
5.4331
1 570 000
1 830 000
1 980 000
352 900 2 280 000

411 400 2 550 000
445 100 2 800 000
512 500
573 200
629 400
1 600
1 500
1 400
2 800
2 600
2 400
73.00
82.50
97.00
160.90
181.90
213.80
232
240
247
9.134
9.449
9.724
2340 ECMA
2344 ECMA
2344 ECMP
200
220
220
7.8740 420 16.5354 138

8.6614 460 18.1102 145
8.6614 460 18.1102 145
5.4331
5.7087
5.7087
1 980 000
2 380 000
2 380 000
445 100 2 800 000

535 000 3 450 000
535 000 3 450 000
629 400
775 600
775 600
1 400
1 300
1 300
2 400
2 200
2 800
97.00
120.00
120.00
213.80
264.60
264.60
247
275
275
9.724
10.827
10.827
2348 ECMA
2356 MA
240
280
9.4488 500 19.6850 155

11.0236 580 22.8346 175
6.1024
6.8898
2 600 000
2 700 000
584 500 3 650 000

607 000 4 300 000
820 500
966 600
1 200
1 000
2 000
1 700
155.00
230.00
341.70
507.10
310
362
12.205
14.252
128
Single row
Standard
Series: 406 424
Size: 30 mm 120 mm
1.1811 in 4.7244 in
Type NUP
Type NU
Designation
Type NJ
Bore
d
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
Mass
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
Diameter
lb
Under roller
F
mm
in
mm
in
406
407
408
30
35
40
1.1811
1.3780
1.5748
90
100
110
3.5433
3.9370
4.3307
23
25
27
0.9055
0.9843
1.0630
60 500
76 500
96 800
13 600
17 200
21 800
53 000
69 500
90 000
11 900
15 600
20 200
9 000
8 000
7 000
11 000
9 500
11 000
0.77
1.05
1.40
1.70
2.30
3.10
45
53
58
1.772
2.087
2.283
409
410
411
45
50
55
1.7717
1.9685
2.1654
120
130
140
4.7244
5.1181
5.5118
29
31
33
1.1417
1.2205
1.2992
106 000
130 000
142 000
23 800
29 200
31 900
102 000
127 000
140 000
22 900
28 500
31 500
6 700
6 000
5 600
7 500
7 000
6 300
1.70
2.05
2.55
3.70
4.50
5.60
65
71
77
2.539
2.787
3.039
412
413
414
60
65
70
2.3622
2.5591
2.7559
150
160
180
5.9055
6.2992
7.0866
35
37
42
1.3780
1.4567
1.6535
168 000
183 000
229 000
37 800
41 100
51 500
173 000
190 000
240 000
38 900
42 700
54 000
5 000
4 800
4 300
6 000
5 600
5 000
3.10
3.95
5.35
6.80
8.70
11.80
83
89
100
3.268
3.516
3.937
415
416
417
75
80
85
2.9528
3.1496
3.3465
190
200
210
7.4803
7.8740
8.2677
45
48
52
1.7717
1.8898
2.0472
264 000
303 000
319 000
59 300
68 100
71 700
280 000
320 000
335 000
62 900
71 900
75 300
4 000
3 800
3 600
4 800
4 500
4 300
6.90
8.05
9.70
15.20
17.70
21.40
105
110
113
4.114
4.331
4.449
418
419
420
90
95
100
3.5433
3.7402
3.9370
225
240
250
8.8583
9.4488
9.8425
54
55
58
2.1260
2.1654
2.2835
380 000
413 000
429 000
85 400
92 800
96 400
415 000
455 000
475 000
93 300
102 300
106 800
3 400
3 200
3 000
4 000
3 600
3 600
11.50
13.50
14.00
25.40
29.80
30.90
124
134
139
4.862
5.256
5.472
421
422
424
105
110
120
4.1339
4.3307
4.7244
260 10.2362
280 11.0236
310 12.2047
60
65
72
2.3622
2.5591
2.8346
501 000
532 000
644 000
112 600
119 600
144 800
570 000
585 000
735 000
128 100
131 500
165 200
2 800
2 600
2 400
3 400
3 200
2 800
19.00
24.00
30.40
41.90
52.90
67.00
145
155
170
5.689
6.102
6.693
129

Full complement
Single row
Standard
Series: NCF 1856 V NCF 18/1000 V
11.0236 in 39.3701 in
Standard
Series: NCF 2224 V
Size: 120 mm
4.7244 in
Type NCF
Designation
Bearings
with
surface treated
rollers
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
Diameter
kg
lb
Over roller
E
mm
in
NCF 1856 V
NCF 1864 V
NCF 1868 V
NCF 1856 CV
NCF 1864 CV
NCF 1868 CV
280
320
340
11.0236
12.5984
13.3858
350
400
420
13.7795
15.7480
16.5354
33
38
38
1.2992
1.4961
1.4961
341 000
440 000
446 000
76 700
98 900
100 300
695 000
900 000
950 000
156 200
202 300
213 600
750
630
600
950
800
750
7.10
10.50
11.00
15.70
23.10
24.30
334 13.150
383 15.079
403 15.866
NCF 1876 V
NCF 1880 V
NCF 1884 V
NCF 1876 CV
NCF 1880 CV
NCF 1884 CV
380
400
420
14.9606
15.7480
16.5354
480
500
520
18.8976
19.6850
20.4724
46
46
46
1.8110
1.8110
1.8110
627 000
627 000
660 000
140 900 1 290 000

140 900 1 340 000
148 400 1 430 000
290 000
301 200
321 500
530
500
480
670
630
600
19.50
20.50
21.00
43.00
45.20
46.30
458 18.031
475 18.701
499 19.646
NCF 1888 V
NCF 1892 V
NCF 1896 V
NCF 1888 CV
NCF 1892 CV
NCF 1896 CV
440
460
480
17.3228
18.1102
18.8976
540
580
600
21.2598
22.8346
23.6220
46
56
56
1.8110
2.2047
2.2047
671 000
913 000
935 000
150 800 1 460 000

205 200 1 960 000
210 200 2 040 000
328 200
440 600
458 600
450
430
400
560
530
500
22.00
34.00
35.50
48.50
75.00
78.30
516 20.315
553 21.772
574 22.579
NCF 18/500 V
NCF 18/530 V
NCF 18/560 V
NCF 18/500 CV
NCF 18/530 CV
NCF 18/560 CV
500
530
560
19.6850
20.8661
22.0472
620
650
680
24.4094
25.5906
26.7717
56
56
56
2.2047
2.2047
2.2047
952 000
990 000
1 020 000
214 000 2 120 000

222 600 2 240 000
229 300 2 360 000
476 600
503 600
530 500
380
360
340
480
450
430
36.50
38.50
40.50
80.50
84.90
89.30
594 23.386
625 24.587
655 25.787
NCF 18/600 V
NCF 18/630 V
NCF 18/670 V
NCF 18/600 CV
NCF 18/630 CV
NCF 18/670 CV
600
630
670
23.6220
24.8031
26.3780
730
780
820
28.7402
30.7087
32.2835
60
69
69
2.3622
2.7165
2.7165
1 050 000
1 250 000
1 300 000
236 000 2 550 000

281 000 2 900 000
292 200 3 150 000
573 200
651 900
708 100
320
300
280
400
360
340
51.50
72.50
76.50
113.50
159.80
168.70
696 27.402
739 29.094
783 30.827
NCF 18/710 V
NCF 18/750 V
NCF 18/800 V
NCF 18/710 CV
710
750
800
27.9528
29.5276
31.4961
870
920
980
34.2520
36.2205
38.5827
74
78
82
2.9134
3.0709
3.2283
1 540 000
1 870 000
1 940 000
346 200 3 750 000

420 400 4 500 000
436 100 4 800 000
843 000
1 011 600
1 079 000
260
240
220
320 92.50
300 110.00
280 130.00
203.90
242.50
286.60
831 32.717
880 34.646
936 36.850
40.5512 82
48.0315 100
3.2283
3.9370
2 010 000
2 920 000
451 800 5 100 000

656 400 7 500 000
1 146 500
1 686 000
200
160
260 135.00
200 230.00
297.60
986 38.819
507.10 1 165 45.866
2.2835
512 000
NCF 18/850 V
NCF 18/1000 V
NCF 2224 V
NCF 2224 CV
850
1 000
120
33.4646 1 030
39.3701 1 220
4.7244
215
8.4646
58
115 100
735 000
165 200
1 400 1 700
9.05
20.00
130
192
7.572
Full complement
Single row
Standard
Series: NJG 2305 VH NJG 2330 VH
Size: 25 mm 150 mm
0.9843 in 5.9055 in
Standard
Size: 440 mm 710 mm
17.3228 in 27.9528 in
Type NCF
Designation
Type NJG
Bearings with
with
surface treated
rollers
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
Diameter
kg
lb
Over roller
E
mm
in
NJG 2305 VH
NJG 2307 VH
NJG 2308 VH
25
35
40
0.9843
1.3780
1.5748
62
80
90
2.4409
3.1496
3.5433
24
31
33
0.9449
1.2205
1.2992
68 200
108 000
145 000
15 300
24 300
32 600
68 000
114 000
156 000
15 300
25 600
35 100
4 500 5 600
3 400 4 300
3 000 3 600
0.38
0.75
1.00
0.80
1.70
2.20
32
45
51
1.248
1.764
2.016
NJG 2309 VH
NJG 2311 VH
NJG 2313 VH
45
55
65
1.7717
2.1654
2.5591
100
120
140
3.9370
4.7244
5.5118
36
43
48
1.4173
1.6929
1.8898
172 000
233 000
303 000
38 700
52 400
68 100
196 000
260 000
360 000
44 100
58 400
80 900
2 800 3 400
2 200 2 800
1 900 2 400
1.45
2.30
3.55
3.20
5.10
7.80
56
67
81
2.209
2.642
3.177
NJG 2315 VH
NJG 2316 VH
NJG 2318 VH
NJG 2315 CVH

NJG 2316 CVH
NJG 2318 CVH
75
80
90
2.9528
3.1496
3.5433
160
170
190
6.2992
6.6929
7.4803
55
58
64
2.1654
2.2835
2.5197
396 000
457 000
528 000
89 000
102 700
118 700
480 000
570 000
670 000
107 900
128 100
150 600
1 600 2 000
1 500 1 900
1 400 1 800
5.35
6.40
8.75
11.80
14.10
19.30
91
98
109
3.591
3.870
4.283
NJG 2320 VH
NJG 2322 VH
NJG 2324 VH
NJG 2320 CVH

NJG 2322 CVH
NJG 2324 CVH
100
110
120
3.9370
4.3307
4.7244
215
240
260
8.4646
9.4488
10.2362
73
80
86
2.8740
3.1496
3.3858
704 000
858 000
952 000
158 300
900 000
192 900 1 060 000
214 000 1 250 000
202 300
238 300
281 000
1 200 1 500
1 100 1 300
1 000 1 200
13.00
17.50
22.50
28.70
38.60
49.60
123
134
147
4.835
5.287
5.803
NJG 2326 VH
NJG 2330 VH
NJG 2326 CVH

NJG 2330 CVH
130
150
5.1181
5.9055
280
320
11.0236 93
12.5984 108
3.6614
4.2520
1 080 000
1 450 000
242 800 1 430 000

326 000 1 930 000
321 500
433 900
950 1 200
800 1 000
28.00
42.50
61.70
93.70
158
183
6.217
7.185
NCF 2888 V
NCF 2892 V
NCF 28/670 V
440
460
670
17.3228
18.1102
26.3780
540
580
820
21.2598
22.8346
32.2835
60
72
88
2.3622
2.8346
3.4646
1 060 000
1 300 000
1 940 000
238 300 2 700 000

607 000
292 200 3 050 000
685 600
436 100 5 300 000 1 191 400
450
430
280
560
530
340
29.00 63.90
44.00 97.00
97.50 214.90
516
553
783
20.315
21.772
30.827
NCF 28/710 V
710
27.9528
870
34.2520
95
3.7402
2 330 000
523 800 6 300 000 1 416 200
260
320 115.00 253.50
831
32.717
131

Full complement
Single row
Standard
Size: 440 mm 710 mm
17.3228 in 27.9528 in
Standard
Series: NCF 2912 V NCF 2964 V
Size: 60 mm 320 mm
2.3622 in 12.5984 in
Type NCF
Designation
Bearings
with
surface treated
rollers
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Diameter
lb
Over roller
E
mm
in
NCF 2888 V
NCF 2892 V
NCF 28/670 V
440
460
670
17.3228
18.1102
26.3780
540
580
820
21.2598
22.8346
32.2835
60
72
88
2.3622
2.8346
3.4646
1 060 000
1 300 000
1 940 000
238 300 2 700 000

607 000
292 200 3 050 000
685 600
436 100 5 300 000 1 191 400
450
430
280
560
530
340
29.00 63.90
44.00 97.00
97.50 214.90
516
553
783
20.315
21.772
30.827
NCF 28/710 V
710
27.9528
870
34.2520
95
3.7402
2 330 000
523 800 6 300 000 1 416 200
260
320 115.00 253.50
831
32.717
NCF 2912 V
NCF 2914 V
NCF 2916 V
NCF 2914 CV
NCF 2916 CV
60
70
80
2.3622
2.7559
3.1496
85
100
110
3.3465
3.9370
4.3307
16
19
19
0.6299
0.7480
0.7480
55 000
76 500
80 900
12 400
17 200
18 200
80 000
116 000
132 000
18 000
26 100
29 700
3 600 4 500
3 000 3 800
2 600 3 400
0.29
0.49
0.55
0.60
1.10
1.20
80
93
103
3.122
3.642
4.043
NCF 2918 V
NCF 2920 V
NCF 2922 V
NCF 2918 CV
NCF 2920 CV
NCF 2922 CV
90
100
110
3.5433
3.9370
4.3307
125
140
150
4.9213
5.5118
5.9055
22
24
24
0.8661
0.9449
0.9449
105 000
128 000
134 000
23 600
28 800
30 100
176 000
200 000
220 000
39 600
45 000
49 500
2 400 3 000
2 200 2 600
1 900 2 400
0.84
1.14
1.23
1.90
2.50
2.70
116
129
141
4.551
5.079
5.563
NCF 2924 V
NCF 2926 V
NCF 2928 V
NCF 2924 CV
NCF 2926 CV
NCF 2928 CV
120
130
140
4.7244
5.1181
5.5118
165
180
190
6.4961
7.0866
7.4803
27
30
30
1.0630
1.1811
1.1811
172 000
205 000
220 000
38 700
46 100
49 500
290 000
360 000
390 000
65 200
80 900
87 700
1 800 2 200
1 600 2 000
1 500 1 900
1.73
2.33
2.42
3.80
5.10
5.30
154
167
180
6.075
6.579
7.087
NCF 2930 V
NCF 2932 V
NCF 2934 V
NCF 2930 CV
NCF 2932 CV
NCF 2934 CV
150
160
170
5.9055
6.2992
6.6929
210
220
230
8.2677
8.6614
9.0551
36
36
36
1.4173
1.4173
1.4173
292 000
303 000
314 000
65 600
68 100
70 600
490 000
530 000
560 000
110 200
119 100
125 900
1 400 1 700
1 300 1 600
1 200 1 500
3.77
4.00
4.30
8.30
8.80
9.50
196
206
216
7.697
8.098
8.504
NCF 2936 V
NCF 2938 V
NCF 2940 V
NCF 2936 CV
NCF 2938 CV
NCF 2940 CV
180
190
200
7.0866
7.4803
7.8740
250
260
280
9.8425
10.2362
11.0236
42
42
48
1.6535
1.6535
1.8898
391 000
440 000
528 000
87 900
98 900
118 700
695 000
780 000
965 000
156 200
175 300
216 900
1 100 1 400
1 100 1 400
1 000 1 300
6.20
6.50
9.10
13.70
14.30
20.10
232
244
262
9.134
9.606
10.315
NCF 2944 V
NCF 2948 V
NCF 2952 V
NCF 2944 CV
NCF 2948 CV
NCF 2952 CV
220
240
260
8.6614
9.4488
10.2362
300
320
360
11.8110
12.5984
14.1732
48
48
60
1.8898
1.8898
2.3622
550 000
583 000
737 000
123 600 1 060 000

131 100 1 140 000
165 700 1 430 000
238 300
256 300
321 500
950 1 200
850 1 100
750
950
9.90
10.60
18.50
21.80
23.40
40.80
283
303
334
11.142
11.929
13.138
NCF 2956 V
NCF 2960 V
NCF 2964 V
NCF 2956 CV
NCF 2960 CV
NCF 2964 CV
280
300
320
11.0236
11.8110
12.5984
380
420
440
14.9606
16.5354
17.3228
60
72
72
2.3622
2.8346
2.8346
880 000
1 120 000
1 140 000
197 800 1 730 000

251 800 2 200 000
256 300 2 360 000
388 900
494 600
530 500
700
670
600
19.70
31.20
32.90
43.40
68.80
72.50
363
391
411
14.280
15.374
16.181
900
800
750
132
Full complement
Single row
Standard
Series: NCF 2968 V NCF 3080 V
Size: 340 mm 400 mm
13.3858 in 15.7480 in
Type NCF
Designation
Bearings
with
surface treated
rollers
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Diameter
lb
Over roller
E
mm
in
NCF 2968 V
NCF 2972 V
NCF 2976 V
NCF 2968 CV
NCF 2972 CV
NCF 2976 CV
340
360
380
13.3858
14.1732
14.9606
460
480
520
18.1102
18.8976
20.4724
72
72
82
2.8346
2.8346
3.2283
1 190 000
1 230 000
1 570 000
267 500 2 500 000

276 500 2 600 000
352 900 3 250 000
562 000
584 500
730 600
560
530
500
700
670
630
35.00 77.20
36.50 80.50
52.50 115.70
431
452
488
16.969
17.776
19.213
NCF 2980 V
NCF 2984 V
NCF 2988 V
NCF 2980 CV
NCF 2984 CV
NCF 2988 CV
400
420
440
15.7480
16.5354
17.3228
540
560
600
21.2598
22.0472
23.6220
82
82
95
3.2283
3.2283
3.7402
1 650 000
1 650 000
2 010 000
370 900 3 450 000

370 900 3 600 000
451 800 4 400 000
775 600
809 300
989 100
480
450
430
600
560
530
54.50 120.20
57.00 125.70
80.50 177.50
511
524
566
20.118
20.630
22.264
NCF 2996 V
NCF 29/500 V
NCF 29/530 V
NCF 2996 CV
NCF 29/500 CV
NCF 29/530 CV
480
500
530
18.8976
19.6850
20.8661
650
670
710
25.5906 100
26.3780 100
27.9528 106
3.9370
3.9370
4.1732
2 290 000
2 330 000
2 640 000
514 800 4 900 000 1 101 500

523 800 5 000 000 1 124 000
593 500 6 100 000 1 371 300
380
380
340
480 98.00 216.10

450 100.00 220.50
430 120.00 264.60
606
635
673
23.858
24.980
26.496
NCF 29/560 V
NCF 29/670 V
NCF 3004 CV
NCF 29/560 CV
NCF 29/670 V
NCF 3004 CV
560
670
20
22.0472
26.3780
0.7874
750
900
42
29.5276 112
35.4331 136
1.6535 16
4.4094
5.3543
0.6299
3 080 000
3 910 000
28 100
692 400 6 700 000 1 506 200

879 000 9 000 000 2 023 200
6 300
28 500
6 400
320
400 140.00 308.60
260
320 245.00 540.10
8 500 10 000
0.11
0.20
709
846
37
27.913
33.307
1.457
NCF 3006 CV
NCF 3008 CV
NCF 3011 CV
NCF 3006 CV
NCF 3008 CV
NCF 3011 CV
30
40
55
1.1811
1.5748
2.1654
55
68
90
2.1654
2.6772
3.5433
19
21
26
0.7480
0.8268
1.0236
39 600
57 200
105 000
8 900
12 900
23 600
44 000
69 500
140 000
9 900
15 600
31 500
6 000
4 800
3 400
7 500
6 000
4 300
0.20
0.31
0.64
0.40
0.70
1.40
50
62
84
1.961
2.437
3.295
NCF 3012 V
NCF 3013 CV
NCF 3014 V
NCF 3012 CV
NCF 3013 CV
NCF 3014 CV
60
65
70
2.3622
2.5591
2.7559
95
100
110
3.7402
3.9370
4.3307
26
26
30
1.0236
1.0236
1.1811
106 000
112 000
128 000
23 800
25 200
28 800
146 000
163 000
173 000
32 800
36 600
38 900
3 400
3 000
2 800
4 000
3 800
3 600
0.69
0.73
1.02
1.50
1.60
2.20
87
93
102
3.421
3.673
4.020
NCF 3016 V
NCF 3018 V
NCF 3020 V
NCF 3016 CV
NCF 3018 CV
NCF 3020 CV
80
90
100
3.1496
3.5433
3.9370
125
140
150
4.9213
5.5118
5.9055
34
37
37
1.3386
1.4567
1.4567
165 000
198 000
209 000
37 100
44 500
47 000
228 000
280 000
310 000
51 300
62 900
69 700
2 400
2 200
2 000
3 000
2 800
2 600
1.43
1.97
2.15
3.20
4.30
4.70
117
130
140
4.614
5.130
5.508
NCF 3024 V
NCF 3030 V
NCF 3038 V
NCF 3024 CV
NCF 3030 CV
NCF 3038 CV
120
150
190
4.7244
5.9055
7.4803
180
225
290
7.0866
8.8583
11.4173
46
56
75
1.8110
2.2047
2.9528
292 000
457 000
792 000
65 600
440 000
102 700
710 000
178 000 1 290 000
98 900
159 600
290 000
1 700
1 300
1 000
2 000
1 600
1 300
3.80
7.50
17.00
8.40
16.50
37.50
168
212
270
6.610
8.335
10.630
NCF 3064 V
NCF 3068 V
NCF 3072 V
NCF 3064 CV
NCF 3068 CV
NCF 3072 CV
320
340
360
12.5984
13.3858
14.1732
480
520
540
18.8976 121
20.4724 133
21.2598 134
4.7638
5.2362
5.2756
1 980 000
2 380 000
2 420 000
445 100 3 450 000

535 000 4 150 000
544 000 4 300 000
775 600
932 900
966 600
560
530
500
700 74.50 164.20

670 100.00 220.50
630 105.00 231.50
447
486
503
17.610
19.134
19.811
NCF 3080 V
NCF 3080 CV
400
15.7480
600
23.6220 148
5.8268
2 970 000
667 700 5 500 000 1 236 400
450
560 145.00 319.70
559
22.012
133

Full complement
Double row
Standard
Series: NNC 4840 V NNCF 4840 V
Size: 200 mm 200 mm
7.8740 in 7.8740 in
Standard
Series: NNCF 4918 V NNCL 4972 V
Size: 90 mm 360 mm
3.5433 in 14.1732 in
Standard
Series: NNCF 5024 V
Size: 120 mm (4.7244 in)
Designation
Type NNCL
Bearings
with
surface treated
rollers
Bore
d
mm
in
Type NNCF
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
Type NNC
lbf
Mass
Diameter
Reference Limiting
speed speed
r/min r/min
kg
lb
Over roller
E
mm
in
NNC 4840 V
NNC 4832 V
NNCF 4834 V
NNC 4840 CV
NNC 4832 CV
NNCF 4834 CV
200
160
170
7.8740
6.2992
6.6929
250
200
215
9.8425
7.8740
8.4646
50
40
45
1.9685
1.5748
1.7717
336 000
260 000
286 000
75 500
58 400
64 300
800 000
610 000
655 000
179 800
137 100
147 200
1 100
1 400
1 300
1 400
1 700
1 600
5.90
3.10
3.90
13.00
6.80
8.60
236
190
202
9.287
7.484
7.941
NNC 4834 V
NNCF 4840 V
NNC 4834 CV
NNCF 4840 CV
170
200
6.6929
7.8740
215
250
8.4646
9.8425
45
50
1.7717
1.9685
286 000
336 000
64 300
75 500
655 000
800 000
147 200
179 800
1 300
1 100
1 600
1 400
4.10
5.50
9.00
12.10
202
236
7.941
9.287
NNCF 4918 V
NNC 4918 V
NNC 4922 V
NNCF 4918 CV
NNC 4918 CV
NNC 4922 CV
90
90
110
3.5433
3.5433
4.3307
125
125
150
4.9213
4.9213
5.9055
35
35
40
1.3780
1.3780
1.5748
161 000
161 000
220 000
36 200
36 200
49 500
300 000
300 000
430 000
67 400
67 400
96 700
2 400
2 400
1 900
3 000
3 000
2 400
1.35
1.35
2.15
3.00
3.00
4.70
116
116
139
4.547
4.547
5.457
NNCL 4930 V
NNCL 4960 V
NNCL 4964 V
NNCL 4930 CV
NNCL 4960 CV
NNCL 4964 CV
150
300
320
5.9055
11.811
12.5984
210
420
440
8.2677 60
16.5354 118
17.3228 118
2.3622
4.6457
4.6457
429 000
1 680 000
1 760 000
96 400
830 000
377 700 3 750 000
395 600 4 050 000
186 600
843 000
910 400
1 400
670
600
1 700
800
750
6.65 14.70
53.00 116.80
56.00 123.50
192 7.559
390 15.362
409 16.102
NNCF 4972 V
NNCL 4972 V
NNCF 4972 CV
NNCL 4972 CV
360
360
14.1732
14.1732
480
480
18.8976 118
18.8976 118
4.6457
4.6457
1 830 000
1 830 000
411 400 4 500 000 1 011 600

411 400 4 500 000 1 011 600
530
530
670
670
62.10 136.90
60.80 134.00
446 17.559
446 17.559
NNCF 5024 V
NNCF 5024 CV
120
4.7244
180
3.1496
539 000
1 700
2 000
7.0866
80
121 200
880 000
197 800
6.77
14.90
134
168
6.614
Full complement
Double row
Sealed
Standard
Series: NNF 5004 ADB-2LSV NNF 5040 ADA-2LSV
Size: 20 mm 200 mm
0.7874 in 7.8740 in
Type NNF
Designation
Bore
Outside diameter
Width
d
D
B
mm
in
mm
in
mm
in
Basic load ratings

Dynamic
C
C
mm
in
Speed
rating
Static
C0
lbf
lbf
Limiting
speed
r/min
Mass
kg
Diameter
lb
Over roller
E
mm
in
NNF 5004 ADB-2LSV

NNF 5005 ADB-2LSV
NNF 5006 ADB-2LSV
20 0.7874
25 0.9843
30 1.1811
42
47
55
1.6535
1.8504
2.1654
30
30
34
1.1811
1.1811
1.3386
29
29
33
1.1417
1.1417
1.2992
45 700
50 100
57 200
10 273
11 263
12 859
55 000
65 500
75 000
12 364
14 725
16 900
3 400
3 000
2 600
0.20
0.24
0.37
0.44
0.53
0.82
36
40
48
1.402
1.591
1.886
NNF 5007 ADB-2LSV

NNF 5008 ADB-2LSV
NNF 5009 ADB-2LSV
35 1.3780
40 1.5748
45 1.7717
62
68
75
2.4409
2.6772
2.9528
36
38
40
1.4173
1.4961
1.5748
35
37
39
1.3780
1.4567
1.5354
70 400
85 800
102 000
15 827
19 289
22 931
91 500
116 000
146 000
20 600
26 100
32 800
2 200
2 000
1 800
0.48
0.56
0.70
1.06
1.23
1.54
55
61
68
2.146
2.402
2.665
NNF 5010 ADB-2LSV

NNF 5011 ADB-2LSV
NNF 5012 ADB-2LSV
50 1.9685
55 2.1654
60 2.3622
80
90
95
3.1496
3.5433
3.7402
40
46
46
1.5748
1.8110
1.8110
39
45
45
1.5354
1.7717
1.7717
108 000
128 000
134 000
24 279
28 776
30 124
160 000
193 000
208 000
36 000
43 400
46 800
1 700
1 500
1 400
0.76
1.18
1.26
1.68
2.60
2.78
73
80
85
2.854
3.150
3.346
NNF 5013 ADB-2LSV

NNF 5014 ADB-2LSV
NNF 5015 ADB-2LSV
65 2.5591
70 2.7559
75 2.9528
100
110
115
3.9370
4.3307
4.5276
46
54
54
1.8110
2.1260
2.1260
45
53
53
1.7717
2.0866
2.0866
138 000
187 000
205 000
31 024
42 039
46 086
224 000
285 000
310 000
50 400
64 071
69 691
1 300
1 200
1 100
1.33
1.87
1.96
2.93
4.12
4.32
90
100
106
3.543
3.937
4.173
NNF 5016 ADB-2LSV

NNF 5017 ADB-2LSV
NNF 5018 ADB-2LSV
80 3.1496
85 3.3465
90 3.5433
125
130
140
4.9213
5.1181
5.5118
60
60
67
2.3622
2.3622
2.6378
59
59
66
2.3228
2.3228
2.5984
216 000
224 000
319 000
48 559
50 357
71 714
335 000
365 000
550 000
75 311
82 055
123 600
1 000
1 000
900
2.71
2.83
3.71
5.97
6.24
8.18
114
120
128
4.469
4.705
5.020
NNF 5019 ADB-2LSV

NNF 5020 ADB-2LSV
NNF 5022 ADA-2LSV
95 3.7402
100 3.9370
110 4.3307
145
150
170
5.7087
5.9055
6.6929
67
67
80
2.6378
2.6378
3.1496
66
66
79
2.5984
2.5984
3.1102
330 000
347 000
380 000
74 187
78 009
85 400
570 000
570 000
695 000
128 100
128 100
156 200
900
850
750
3.88
3.95
6.45
8.55
8.71
14.20
131
138
155
5.157
5.433
6.083
NNF 5024 ADA-2LSV

NNF 5026 ADA-2LSV
NNF 5028 ADA-2LSV
120 4.7244
130 5.1181
140 5.5118
180
200
210
7.0866
7.8740
8.2677
80
95
95
3.1496
3.7402
3.7402
79
94
94
3.1102
3.7008
3.7008
402 000
572 000
594 000
90 400
128 600
133 500
750 000
1 040 000
1 120 000
168 600
233 800
251 800
700
630
600
6.90
10.50
11.00
15.20
23.10
24.30
164
184
196
6.457
7.224
7.697
NNF 5030 ADA-2LSV

NNF 5032 ADA-2LSV
NNF 5034 ADA-2LSV
150 5.9055
160 6.2992
170 6.6929
225
240
260
8.8583 100
9.4488 109
10.2362 122
3.9370
4.2913
4.8031
99
108
121
3.8976
4.2520
4.7638
693 000
721 000
935 000
155 800
162 100
210 200
1 290 000
1 400 000
1 800 000
290 000
314 700
404 600
560
500
480
13.50
16.50
22.50
29.80
36.40
49.60
209
223
239
8.236
8.764
9.409
NNF 5036 ADA-2LSV

NNF 5038 ADA-2LSV
NNF 5040 ADA-2LSV
180 7.0866
190 7.4803
200 7.8740
280
290
310
11.0236 136
11.4173 136
12.2047 150
5.3543
5.3543
5.9055
135
135
149
5.3150
5.3150
5.8661
1 080 000
1 100 000
1 340 000
242 800
247 300
301 200
2 120 000
2 200 000
2 900 000
476 600
494 600
651 900
450
430
400
30.00
31.50
42.00
66.10
69.40
92.60
259
267
284
10.197
10.524
11.181
135
Notes
136
Spherical roller
bearings
Nomenclature
ECB 22240 CCK JA / C3 W33

1
3
2
1. Prefix:
4. Cage designs / seals:
6. Features:
ECB
J
JA
M2
Pressed steel cage
Without relubrication feature

(W33) on E style bearings only
W4
High point of eccentricity marked

on inner ring or sleeve
MA
2CS
Machine brass cage, ring guided
W22
Special reduced outside

diameter tolerance for outer ring
W26
Six lubrication holes in inner ring
W31
Bearing inspected to special

quality requirement
W33
Three oil holes and circumferential

groove in outside diameter
W33X
Lubrication groove and six

holes in outer ring
W502
Combination of W22 & W33
W507
Combination of W4, W31 & W33
W509
Combination of W26, W31 & W33
HA1
Case hardened outer and

inner rings
HA3
Case hardened inner rings

(equal to ECB)
VA405
Vibrating screen specification
VA751VA759
Printing/coater roller specification
BS2
Air melt carburized steel,

inner ring only
Two row spherical roller
bearing, special dimensions
2. Internal design:
CA
Integral side flanges,

inner ring guided
one-piece machined brass cage
CAC
Same as CA designed spherical

roller bearing with improved roller
guidance
CAFA
Bearing with symmetrical rollers,

retaining flanges on the inner ring.
Guide ring centered on the inner
ring, one-piece machined steel
cage of the double pronged type
centered in the outer ring
CAMA
As CAFA, but with a machined

brass double pronged cage
CC
Flangeless inners, symmetrical

rollers, floating guide ring, pressed
steel cage
Improved internal design,

W33 feature is standard
3. Bore type:
Cylindrical bore
tapered bore
K30
tapered bore
2CS2
2CS5
F
Y
Hardened steel cage, ring guided

Machined brass roller guided cage,
no guide ring
Sheet steel reinforced contact seal

of acrylonitrile butadiene rubber
(NBR) on both sides of the bearing.
Annular groove and three lubrication
holes in the outer ring covered with
a polymer band. Lubricated with a
medium temperature grease.
of fluoro rubber (FPM) on both sides
of the bearing. Annular groove and
three lubrication holes in the outer
ring; covered with a polymer band.
Lubricated with a high temperature
grease.
of hydrogenated acrylonitrile butadiene (HNBR) on both sides of the
bearing. Otherwise same as 2CS2.
Machine steel cage, ring guided
Pressed brass cage, ring guided
5. Clearance / tolerance:
C1
C2
(C0)*
C3
C4
C08
Clearance < C2
VT143
SKF grease LGEP2 supplied in

sealed spherical roller bearings
Clearance < Normal

Normal clearance
Clearance > Normal
Clearance > C3
RBEC 5 running accuracy,
inner and outer rings
137
Spherical roller bearings
Product
Details
Technical
features
Boundary dimensions
Tolerances
SKF spherical roller bearings are manufactured as Standard to Normal

(RBEC 1, ISO P7) tolerances. SKF Explorer bearings up to 315 mm bore diameter are
produced to higher precision than Normal tolerances. The width tolerance is
considerably tighter*. The running accuracy is to tolerance class P5 as Standard.
For larger bearings P5 tolerances are also available with the suffix C08 or closer
tolerances are available with suffix VQ424. Vibratory bearings are manufactured to
bore P6 and O.D. P5.
Heat stabilization
392 F (200 C)
Misalignment
Series
Series
Series
Series
Series
21300
22300
23100
23900
24100
1 degree
2 degrees
1.5 degrees
1.5 degrees
2.5 degrees
Series
Series
Series
Series
22200
23000
23200
24000
1.5 degrees
1.5 degrees
2.5 degrees
2 degrees
Cage material
Standard
Steel
Optional
Machined brass (CA) larger bearings only
Axial load max
For adapter mounts Fap = 3 x B x d

where B = bearing width (mm)
Fap = axial load in Newtons
For cylindrical mounts contact SKF
Seals
2CS 2 nitrile seals with med. temp. grease

2CS2 2 vitron seals with high temp. grease
2CS5 2 nitrile seals with high temp. grease
* See width tolerances in SKF General Catalog (publication #6000 EN)
Standard
spherical roller bearing
138
Sealed
Shaker screen
Printing press
Introduction
Introduction
Basic design
Spherical roller bearings have two rows of

rollers with a common sphered raceway in the
outer ring. The two inner ring raceways are
inclined at an angle to the bearing axis. The
bearings are self-aligning and consequently
insensitive to errors of alignment of the shaft
relative to the housing, and to shaft bending.
In addition to radial loads, the bearings can
also accommodate axial loads acting in both
directions.
SKF spherical roller bearings have a large
number of long, symmetrical rollers of large
diameter and consequently have very high load
carrying capacity. Their internal design differs
slightly depending on series and size, but has
been continually improved over the years. The
special form and optimized surface finish of the
raceways provide that the bearings, especially
those of the SKF Explorer, CC, CAC and E
designs, have a minimum of friction. These
bearings have lower operating temperatures or
can accommodate heavier axial loads, or can be
operated at higher speeds than conventional
spherical roller bearings.
The E design constitutes the newer SKF
standard design for spherical roller bearings.
There have been many developments and
improvements in design over the years and
they have been put together to produce an even
better bearingthe SKF Explorer. This represents a new class of performance. Explorer
bearings give more performance for the same
size: they can carry more load for longer, or
they can carry the same load as before even
more reliably for much, much longer.
SKF spherical roller bearings are available
with cylindrical bore and tapered bore. The
tapered bore of bearings in series 240 and 241
have a taper of 1:30 (designation suffix K30)
whereas the taper of all other bearings is 1:12
(suffix K).
SKF spherical roller bearings are made to one

of the designs described in the following paragraphs, depending on size and series.
CC and EC designs (Figure 1a)

These bearings have symmetrical rollers, a
flangeless inner ring and a pressed steel cage
for each roller row. The guide ring is centered
on the inner ring between the two rows of
rollers. EC design bearings incorporate reinforced roller sets for increased load carrying
capacity. The surface finish of the rollers and
raceways of bearings of the CC design has been
optimized to promote roller guidance and
reduce friction.
CAC, ECAC, CA and ECA designs

(Figure 1b)
These designs are used for the larger sizes of
SKF spherical roller bearings. The rollers are
symmetrical and the inner ring has retaining
flanges. The guide ring is centered on the inner
ring between the two rows of rollers and the
cage is a one-piece, double pronged machined
brass cage. The CAC and ECAC designs
incorporate the surface finish refinements of
the CC design and the ECAC and ECA designs
have reinforced roller complements for
increased load carrying capacity.
E design (Figure 1c)

These bearings have symmetrical rollers, a
flangeless inner ring and a sintered guide ring
between the two rows of rollers, which is positioned towards the outer ring and centered on
the two pressed steel window-type cages used
for each row of rollers.
The E design bearings incorporate all the
advantages of the well-proven SKF CC bearings
as well as additional refinements. The pressed
steel cages have been newly developed and
permit the inclusion of a greater number and/or
larger diameter rollers of increased length,
Figure 1
imparting even higher load carrying capacity to

the bearings.
The positioning of the guide ring towards the
outer ring enables lubrication at the roller end
guide ring contact to be improved. The guide
ring contributes to the reduced friction in the
bearing as it helps to guide the rollers in the
unloaded zone and assists their entry into the
loaded zone.
Product highlights
Self-aligning, robust design
Allows misalignment between shaft
and housing without increasing friction
or reducing bearing life. Also insensitive
to misalignment caused by shaft or
housing deflection due to heavy load.
Very high load carrying capacity

Optimum internal design provides
maximum radial and axial load carrying
capacity.
Reduced friction and minimum

heat generation
Self-guiding rolleran SKF patent
means reduced friction and minimum
heat generation.
Excellent performance at high

temperatures
High-strength, dimensionally stable
bearing rings minimize the risk of
ring breakage and also allow good
performance at high temperatures.
Seals integration
Under normal operating conditions,
sealed SKF spherical roller bearings are
greased for life and make external seals
unnecessarysimplifying bearing
arrangements and requiring minimum
maintenance.
Special bearing series available

for demanding applications
High precision printing press bearings
and bearings for vibrating screen
applications.
CC and EC
designs
CAC, ECAC, CA and ECA

designs
c
E design
139

Introduction
Variations
SKF Explorer class

bearings
Availability
The popular small and medium size spherical
roller bearings in the series 213, 222, 223,
230, 231, 232 and a few sizes in the 239, 240
and 241 are available as SKF Explorer bearings.
The range is being extended in these bearings
series as well as in other series.
In the product tables, the SKF Explorer
bearing designations are printed in blue.
Their robust design and high reliability make

SKF standard and Explorer spherical roller
bearings suitable for most applications.
However, extraordinary demands call for bearings with extraordinary features. Some applications can be enhanced with the following:
Sealed bearings
Annular groove and lubrication holes
Bearings for vibrating applications
Printing press bearings
Product designations
Sealed bearings
The SKF Explorer bearings retain the designations of the earlier standard bearings, e.g.
22218 E or 23032 CC/W33. However, each
bearing and its box is marked with the name
SKF Explorer so that there can be no
confusion.
Additional details on Explorer performance
class bearings can be found on page 23.
Sealed SKF spherical roller bearings

(Figure 2) are cost effective solutions for highly
contaminated environments. Sealed bearings
are available in either the E or CC design. CC
design bearings generally have the same
boundary dimensions as the open (unsealed)
version. E design bearings may be slightly
wider. (BS2 prefix)
There are two contact seals developed specially for self-aligning bearings: one seal (2CS)
is for normal temperatures -22 to +230 F
(-30 to +110 C) and the other (2CS2) for
operating temperatures between -22 to
+302 F (-30 to +150 C). Both variants efficiently prevent contaminants from penetrating
to the rolling contact area. This is true not only
in operation, but also before and during
mounting.
Two high-quality greases are also used: SKF
grease LGEP 2 for normal temperatures and a
special high-temperature grease to match the
high-temperature seals. In the bearing tables,
all bearings which are available in a sealed
version are listed on page 163.
SKF sealed spherical roller bearings permit
misalignments of up to 0.5 of the inner ring
with respect to the outer ring in applications
where the inner ring rotates. Under many
operating conditions, sealed spherical roller
bearings may not require relubrication.
However, where loads are heavy or the
bearings operate at high speeds, or at temperatures above 158 F (+70 C), they should be
relubricated. This may be achieved via the
annular groove and lubrication holes in the
outer ring. Details regarding sealed spherical
roller bearings can be supplied on request.
Figure 2
Sealed bearing
140
Warning:
SKF sealed roller bearings that are fitted with
fluoro rubber (elastomer) seals (2CS2) can
cause serious bodily injury if used improperly.
The seals are suitable for operation up to
392 F (200 C). A fluoroelastomer base will
resist ignition under any conditions outside
special furnace condition, but if
exposure to heat (due to fire or any other
conditions) is extreme, e.g. over 572 F
(300 C) for more than a brief time,
degradation will occur. Fluoro rubber emits
dangerous fumes at temperatures of 572 F
(300 C) and above. This may occur if the
seals are subjected to extreme heat during
dismounting, for example. Once it has been
overheated, fluoro rubber will remain dangerous to handle, even when it has cooled down.
This degraded product is a major health and
safety danger due to the evolution of hydrofluoric acid (HF). It is necessary to handle
overheated fluoro rubber seals carefully:
always observe safety instructions and wear
goggles and protective gloves. Under no
circumstances should material (hot or cold) be
allowed to contact skin. If hands or eyes have
come into contact with the material or fumes,
they should be washed or rinsed in plenty of
water. A doctor should always be consulted,
especially if the fumes have been inhaled.
Decontamination can be carried out using
limewater (calcium hydroxide solution); use of
P.V.C. gloves is essential. After neutralization,
the degraded seal can be disposed of in a
similar manner to an un-degraded one.
The user is responsible for the correct
handling of the seals during bearing life and
for the proper disposal of used seals. Seals of
fluoro rubber and bearings incorporating
them are not dangerous to handle provided
they have never been overheated.
Introduction
Annular groove and lubrication holes

(W33)
To facilitate efficient bearing lubrication, all SKF
spherical roller bearings are provided with an
annular groove and three lubrication holes in
the outer ring as standard except those of
series 213 CC, and CC design bearings having
an outside diameter smaller than 150 or 180
mm (depending on series).
Designation suffix W33 is used to identify
this feature on bearings of the CC, C, EC, ECC,
CAC, ECAC, CA and ECA designs. The suffix is
not used with the E design bearings as the
lubrication groove and three holes feature is
an integral part of the new standard E design.
If E design bearings are required without this
feature, then suffix W must be added to the
bearing designation; for example, 22312 EW or
22312 EKW.
Bearings for vibrating applications

Continuing research into the operating
characteristics of roller bearings in extreme
environments, such as those encountered by
screen bearings, has been an ongoing and
integral part of the SKF search to optimize the
value received by our customers.
Laboratory and field testing over prolonged
periods have proven the durability we have
sought to engineer into these bearings.
Series 4523 and 4533 CACM2 as well as
Series 223 / 233 and VA405 / VA406 screen
bearings are the proven result of years of
intensive and innovative applications research.
Series 22300 / VA405 bearings with special
clearance are modified to cope with shaft
deflection encountered in vibrating applications.
They are characterized by a hardened floating
guide ring centered in the outer ring which
guides the highly wear resistant, surface
hardened window-type steel cages. To prevent
fretting corrosion at the non-locating bearing
position, a special version with PTFE-coated
cylindrical bore is available (VA406). Contact
SKF Applications Engineering for further details.
Printing press bearings

Preloaded spherical roller bearings have
been made in many sizes for use on various
cylinders in printing presses. These bearings,
in addition to being extensively used by the
printing industry, are also used on embossing,
coating and slitting machines.
Special design features, which have
contributed to their outstanding performance,
are as followed:
Highest precision O.D. tolerance
maintains a controlled housing fit
Torque tested bearings are run in at
the factory
Interchangeability within one size against
a properly made spacer resulting in the
desired preload
Special precision roller grouping.
Special inner ring runout closer than
normal
High point of eccentricity (both magnitude
and location) marked on inner ring
All bearings are marked with a serial
number and the individual bearing drive up
required to achieve a specific internal
preload
Special unmounted radial internal
clearance
Accessories for optimum

performance
Any system is only as strong as its weakest
member. Therefore, SKF offers not only a wide
range of spherical roller bearings, but also a
full line of quality bearing accessories to go
with them.
Adapter and withdrawal sleeves

Adapter and withdrawal sleeves are used to
locate bearings with a tapered bore on
cylindrical or shouldered shafts. They facilitate
bearing mounting and dismounting and in
many cases simplify bearing arrangement
design. Consequently, several series of quality
sleeves are included in the SKF product range.
More detailed information on the sleeves can
be found in the Accessories Section of the
Split Pillow Block Inch and Split Pillow
Block Metric chapters in this catalog.
Lock nuts
To lock bearings in position on a shaft, SKF
supplies a variety of lock or shaft nuts. Lock
nuts N, KM(L) and HM use a locking washer
or a locking clip to engage a groove on the
shaft. KMF, KMK, KMT and KMTA locknuts are
locked on the shaft with either grub screws or
locking pins.
Bearing housings
Bearing housings must be suited to the
demands placed on the bearings that they
house, e.g. load, accuracy, type of lubrication
and lubricant, sealing, etc. Therefore, SKF offers
a comprehensive range of high-quality standard and special housings. These, together with
the appropriate SKF spherical roller bearings,
form economic and interchangeable bearing
units, which meet all the performance demands
of a bearing application.
141

Introduction
Special solutions
SKF supplies different types of spherical
roller bearings in addition to those shown
in this catalog, including:
Internal clearance
Masses
Internal radial clearance
The masses given in the bearing tables

are for bearings with cylindrical bore; the
masses of bearings with tapered bore
are somewhat less. For a specific value,
contact SKF Applications Engineering.
SKF spherical roller bearings are manufactured

as standard with Normal radial internal clearance. Nearly all the bearings are also available
with the larger C3 clearance and some can be
supplied with the even larger C4 clearance.
Some sizes can be delivered with C2 clearance
which is smaller than Normal. The availability
of bearings with radial internal clearances other
than Normal (including C5) should be checked
before design change or order placement.
The limits for the various clearances can be
found in Table 1, for cylindrical bores and
Table 2, for tapered (K) bores and are in
accordance with ISO 5753-1991 (ABMA
standard 20), where d 1,000 mm (39.3701").
They are valid for zero measuring load and
before mounting.
Spherical roller bearings for heavy

engineering applications
Split spherical roller bearings
Triple ring spherical roller bearings
Rolling mill bearings
Table 1
Radial internal clearance of spherical roller bearings with cylindrical bore
Bore
diameter
d
over incl.
mm
over
in
incl.
C2
min
m
max
min
in
max
Normal
min max
m
min
in
max
C3
min
m
max
min
in
max
C4
min max
m
min
in
max
C5
min
m
max
min
in
18
24
30
24
30
40
0.7087
0.9449
1.1811
0.9449
1.1811
1.5748
10
15
15
20
25
30
0.0004
0.0006
0.0006
0.0008
0.0010
0.0012
20
25
30
35
40
45
0.0008
0.0010
0.0012
0.0014
0.0016
0.0018
35
40
45
45
55
60
0.0014
0.0016
0.0018
0.0018
0.0022
0.0024
45
55
60
0.0018
0.0022
0.0024
0.0024
0.0030
0.0031
60
75
80
75
95
100
0.0024 0.0030
0.0030 0.0037
0.0031 0.0039
40
50
65
50
65
80
1.5748
1.9685
2.5591
1.9685
2.5591
3.1496
20
20
30
35
40
50
0.0008
0.0008
0.0012
0.0014
0.0016
0.0020
35
40
50
55
65
80
0.0014
0.0016
0.0020
0.0022
0.0026
0.0031
55
65
80
75
90
110
0.0022
0.0026
0.0031
0.0030
0.0035
0.0043
75 100
90 120
110 145
0.0030
0.0035
0.0043
0.0039
0.0047
0.0057
100
120
145
125
150
180
0.0039 0.0049
0.0047 0.0059
0.0057 0.0071
80 100
100 120
120 140
3.1496
3.9370
4.7244
3.9370
4.7244
5.5118
35
40
50
60
75
95
0.0014
0.0016
0.0020
0.0024
0.0030
0.0037
60
75
95
100
120
145
0.0024
0.0030
0.0037
0.0039
0.0047
0.0057
100 135
120 160
145 190
0.0039
0.0047
0.0057
0.0053
0.0063
0.0075
135 180
160 210
190 240
0.0053
0.0063
0.0075
0.0071
0.0083
0.0094
180
210
240
225
260
300
0.0071 0.0089
0.0083 0.0102
0.0094 0.0118
140 160
160 180
180 200
5.5118
6.2992
7.0866
6.2992
7.0866
7.8740
60
65
70
110
120
130
0.0024
0.0026
0.0028
0.0043
0.0047
0.0051
110 170
120 180
130 200
0.0043
0.0047
0.0051
0.0067
0.0071
0.0079
170 220
180 240
200 260
0.0067
0.0071
0.0079
0.0087
0.0094
0.0102
220 280
240 310
260 340
0.0087
0.0094
0.0102
0.0110
0.0122
0.0134
280
310
340
350
390
430
0.0110 0.0138
0.0122 0.0154
0.0134 0.0169
200 225
225 250
250 280
7.8740
8.8583
9.8425
8.8583
9.8425
11.0236
80 140
90 150
100 170
0.0031
0.0035
0.0039
0.0055
0.0059
0.0067
140 220
150 240
170 260
0.0055
0.0059
0.0067
0.0087
0.0094
0.0102
220 290
240 320
260 350
0.0087
0.0094
0.0102
0.0114
0.0126
0.0138
290 380
320 420
350 460
0.0114
0.0126
0.0138
0.0150
0.0165
0.0181
380
420
460
470
520
570
0.0150 0.0185
0.0165 0.0205
0.0181 0.0224
280 315
315 355
355 400
11.0236 12.4016
12.4016 13.9764
13.9764 15.7480
110 190
120 200
130 220
0.0043
0.0047
0.0051
0.0075
0.0079
0.0087
190 280
200 310
220 340
0.0075
0.0079
0.0087
0.0110
0.0122
0.0134
280 370
310 410
340 450
0.0110
0.0122
0.0134
0.0146
0.0161
0.0177
370 500
410 550
450 600
0.0146
0.0161
0.0177
0.0197
0.0217
0.0236
500
550
600
630
690
750
0.0197 0.0248
0.0217 0.0272
0.0236 0.0295
400 450
450 500
500 560
15.7480 17.7165
17.7165 19.6850
19.6850 22.0472
140 240
140 260
150 280
0.0055
0.0055
0.0059
0.0094
0.0102
0.0110
240 370
260 410
280 440
0.0094
0.0102
0.0110
0.0146
0.0161
0.0173
370 500
410 550
440 600
0.0146
0.0161
0.0173
0.0197
0.0217
0.0236
500 660
550 720
600 780
0.0197
0.0217
0.0236
0.0260
0.0283
0.0307
660
720
780
820 0.0260 0.0323

900 0.0283 0.0354
1000 0.0307 0.0394
560 630
630 710
710 800
22.0472 24.8031
24.8031 27.9528
27.9528 31.4961
170 310
190 350
210 390
0.0067
0.0075
0.0083
0.0122
0.0138
0.0154
310 480
350 530
390 580
0.0122
0.0138
0.0154
0.0189
0.0209
0.0228
480 650
530 700
580 770
0.0189
0.0209
0.0228
0.0256
0.0276
0.0303
650 850 0.0256

700 920 0.0276
770 1010 0.0303
0.0335
0.0362
0.0398
850 1100 0.0335 0.0433

920 1190 0.0362 0.0469
1010 1300 0.0398 0.0512
800 900 31.4961 35.4331

900 1000 35.4331 39.3701
1000 1120 39.3701 44.0945
230 430
260 480
290 530
0.0091
0.0102
0.0114
0.0169
0.0189
0.0209
430 650
480 710
530 780
0.0169
0.0189
0.0209
0.0256
0.0280
0.0307
650 860
710 930
780 1020
0.0256
0.0280
0.0307
0.0339
0.0366
0.0402
860 1120 0.0339

930 1220 0.0366
1020 1330 0.0402
0.0441
0.0480
0.0524
1120 1440 0.0441 0.0567

1220 1570 0.0480 0.0618
1330 1720 0.0524 0.0677
1120 1250 44.0945 49.2126
320 580
0.0126
0.0228
580 860
0.0228
0.0339
860 1120
0.0339
0.0441
1120 1460 0.0441
0.0575
1460 1870 0.0575 0.0736
142
60
75
80
max
Introduction
Loads

standard spherical roller bearings

vibrating screen bearings
Axial load carrying capacity of bearings

mounted on adapter sleeves
The equivalent dynamic bearing load for

spherical roller bearings can be obtained from:
For the normal configuration of a shaft supported by a bearing at each end, the equivalent dynamic bearing load is mostly a function
of the centrifugal force and is calculated from:
If spherical roller bearings with adapter sleeves

are mounted on smooth shafts with no fixed
abutment, the magnitude of the axial load that
can be supported is determined by the friction
between the shaft and sleeve. Provided the
bearings are mounted correctly, the permissible
axial load can be calculated from:
Fap = 3 B d
where
Fap = maximum permissible axial load, N
B = bearing width, mm
d = bearing bore diameter, mm
P = Fr + Y1Fa when Fa / Fr e
P = 0.67 Fr + Y2Fa when Fa / Fr > e
2
P = .5fd WRn for N & mm
91,100
where
P = equivalent dynamic bearing load, N
Fr = actual radial bearing load, N
Fa = actual axial bearing load, N
Y1, Y2 = axial load factors for the bearings
2
P = .5fd WRn for lb & in
35,200
where
Appropriate values of the factors e, Y1 and Y2

will be found in the bearing tables for each
individual bearing.
W = mass of eccentric part of

shaft kg (lb mass)
R = eccentric radius, mm (in)
n = rev / m
fd = vibrating application factor = 1.2
P = equivalent Load, N (lb force)
Table 2
Radial internal clearance of spherical roller bearings with tapered bore

Bore
diameter
d
over incl.
mm
over
in
incl.
C2
min
m
max
min
in
max
Normal
min max
m
min
in
max
C3
min
m
max
min
in
max
C4
min max
m
min
in
max
C5
min
m
max
min
in
24
30
40
30
40
50
0.9449
1.1811
1.5748
1.1811
1.5748
1.9685
20
25
30
30
35
45
0.0008
0.0010
0.0012
0.0012
0.0014
0.0018
30
35
45
40
50
60
0.0012
0.0014
0.0018
0.0016
0.0020
0.0024
40
50
60
55
65
80
0.0016
0.0020
0.0024
0.0022
0.0026
0.0031
55
65
80
75
85
100
0.0022
0.0026
0.0031
0.0030
0.0033
0.0039
85
100
105
130
0.0033 0.0041
0.0039 0.0051
50
65
80
65
80
100
1.9685
2.5591
3.1496
2.5591
3.1496
3.9370
40
50
55
55
70
80
0.0016
0.0020
0.0022
0.0022
0.0028
0.0031
55
70
80
75
95
110
0.0022
0.0028
0.0031
0.0030
0.0037
0.0043
75 95
95 120
110 140
0.0030
0.0037
0.0043
0.0037
0.0047
0.0055
95 120
120 150
140 180
0.0037
0.0047
0.0055
0.0047
0.0059
0.0071
120
150
180
160
200
230
0.0047 0.0063
0.0059 0.0079
0.0071 0.0091
100 120
120 140
140 160
3.9370
4.7244
5.5118
4.7244
5.5118
6.2992
65
80
90
100
120
130
0.0026
0.0031
0.0035
0.0039
0.0047
0.0051
100 135
120 160
130 180
0.0039
0.0047
0.0051
0.0053
0.0063
0.0071
135 170
160 200
180 230
0.0053
0.0063
0.0071
0.0067
0.0079
0.0091
170 220
200 260
230 300
0.0067
0.0079
0.0091
0.0087
0.0102
0.0118
220
260
300
280
330
380
0.0087 0.0110
0.0102 0.0130
0.0118 0.0150
160 180
180 200
200 225
6.2992
7.0866
7.8740
7.0866
7.8740
8.8583
100 140
110 160
120 180
0.0039
0.0043
0.0047
0.0055
0.0063
0.0071
140 200
160 220
180 250
0.0055
0.0063
0.0071
0.0079
0.0087
0.0098
200 260
220 290
250 320
0.0079
0.0087
0.0098
0.0102
0.0114
0.0126
260 340
290 370
320 410
0.0102
0.0114
0.0126
0.0134
0.0146
0.0161
340
370
410
430
470
520
0.0134 0.0169
0.0146 0.0185
0.0161 0.0205
225 250
250 280
280 315
8.8583 9.8425
9.8425 11.0236
11.0236 12.4016
140 200
150 220
170 240
0.0055
0.0059
0.0067
0.0079
0.0087
0.0094
200 270
220 300
240 330
0.0079
0.0087
0.0094
0.0106
0.0118
0.0130
270 350
300 390
330 430
0.0106
0.0118
0.0130
0.0138
0.0154
0.0169
350 450
390 490
430 540
0.0138
0.0154
0.0169
0.0177
0.0193
0.0213
450
490
540
570
620
680
0.0177 0.0224
0.0193 0.0244
0.0213 0.0268
315 355
355 400
400 450
12.4016 13.9764
13.9764 15.7480
15.7480 17.7165
190 270
210 300
230 330
0.0075
0.0083
0.0091
0.0106
0.0118
0.0130
270 360
300 400
330 440
0.0106
0.0118
0.0130
0.0142
0.0157
0.0173
360 470
400 520
440 570
0.0142
0.0157
0.0173
0.0185
0.0205
0.0224
470 590
520 650
570 720
0.0185
0.0205
0.0224
0.0232
0.0256
0.0283
590
650
720
740
820
910
0.0232 0.0291
0.0256 0.0323
0.0283 0.0358
450 500
500 560
560 630
17.7165 19.6850
19.6850 22.0472
22.0472 24.8031
260 370
290 410
320 460
0.0102
0.0114
0.0126
0.0146
0.0161
0.0181
370 490
410 540
460 600
0.0146
0.0161
0.0181
0.0193
0.0213
0.0236
490 630
540 680
600 760
0.0193
0.0213
0.0236
0.0248
0.0268
0.0299
630 790
680 870
760 980
0.0248
0.0268
0.0299
0.0311
0.0343
0.0386
790
870
980
1000 0.0311 0.0394

1100 0.0343 0.0433
1230 0.0386 0.0484
630 710
710 800
800 900
24.8031 27.9528
27.9528 31.4961
31.4961 35.4331
350 510
390 570
440 640
0.0138
0.0154
0.0173
0.0201
0.0224
0.0252
510 670
570 750
640 840
0.0201
0.0224
0.0252
0.0264
0.0295
0.0331
670 850
750 960
840 1070
0.0264
0.0295
0.0331
0.0335
0.0378
0.0421
850 1090 0.0335

960 1220 0.0378
1070 1370 0.0421
0.0429
0.0480
0.0539
1090 1360 0.0429 0.0535

1220 1500 0.0480 0.0591
1370 1690 0.0539 0.0665
900 1000 35.4331 39.3701

1000 1120 39.3701 44.0945
1120 1250 44.0945 49.2126
490 710
530 770
570 830
0.0193
0.0209
0.0224
0.0280
0.0303
0.0327
710 930 0.0280

770 1030 0.0303
830 1120 0.0327
0.0366
0.0406
0.0441
930 1190
1030 1300
1120 1420
0.0366
0.0406
0.0441
0.0469
0.0512
0.0559
1190 1520 0.0469

1300 1670 0.0512
1420 1830 0.0559
0.0598
0.0657
0.0720
1520 1860 0.0598 0.0732

1670 2050 0.0657 0.0807
1830 2250 0.0720 0.0886
max
143

Introduction
Minimum load
Misalignment

all ball and roller bearings, they must always
be subjected to a given minimum load. This
is also true of spherical roller bearings, particularly if they run at high speeds where the
inertia forces of the rollers and cage, and the
influence on the rolling conditions in the
bearing and may cause damaging sliding
the raceways.
using the SKF Interactive Engineering Catalog
on the SKF website www.skf.com or by contacting SKF Applications Engineering. However,
the weight of the components supported by the
bearing, together with the external forces, often
exceeds the requisite minimum load. If this is
not the case, an additional radial load must be
applied to the bearing, for example, by increasing belt tension or similar means.
The design of spherical roller bearings is such

that they are inherently self-aligning, i.e. angular misalignment between the outer and inner
rings can be accommodated without any effect
on bearing performance. Under Normal loads
and operating conditions (C / P>10), and when
misalignment is constant in position with
respect to the outer ring, the guideline values
for permissible misalignment given in Table 3
apply. Whether these values can be fully
exploited or not depends on the design of
the bearing arrangement, the type of seals
used, etc.
Additional sliding is caused in the bearing
under certain operating conditions when the
position of the misalignment is not constant
with respect to the bearing outer ring, for
example:

Table 3
Permissible angular misalignment
Bearing
series
sizes1)
Permissible
angular
misalignment
degrees
Series 213
2.0
Series 222
sizes < 52
sizes 52
2.0
1.5
Series 223
3.0
Series 230
sizes < 56
sizes 56
2.0
2.5
Vibrating screens with rotating imbalance

and therefore rotating deflection of the
shaft (Figure 3), or
Deflection-compensating rolls of paper
machines where the stationary shaft is
bent,
Series 231
sizes < 60
sizes 60
2.0
3.0
Series 232
sizes < 52
sizes 52
2.5
3.5
Therefore, with reference to bearing friction

and associated heat generation, it is recommended that misalignment of the inner ring
with respect to the outer ring should not
exceed a few tenths of a degree.
Sealed bearings can accommodate angular
misalignments of the shaft with respect to the
housing of up to approximately 0.5. Provided
the guideline value is not exceeded, there will
be no detrimental effect on the efficiency of
the seals.
Series 238
1.5
Series 239
1.5
Series 240
2.0
Series 241
sizes < 64
sizes 64
2.5
3.5
Series 248
1.5
Series 249
2.5
1)
Last two figures of bearing designation
Figure 3
144

Series: 21304 CC 21320 E
Size: 20 mm 100 mm
0.7874 in 3.9370 in
Cylindrical bore
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Speed rating
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Dynamic
C
N
CC design
Tapered bore
Static
C0
E design
Mass
Calculation
factors
kg
lb
e
-
Y1
-
Y2
-
21305 CC
21306 CC
21307 CC
25
30
35
0.9843
1.1811
1.3780
62
72
80
2.4409
2.8346
3.1500
17
19
21
0.6692
0.7480
0.8268
41 400
55 200
65 600
9 310
12 400
14 700
41 500
61 000
72 000
9 300
13 700
16 000
8 500 12 000
7 500 10 000
6 700 9 500
0.28
0.41
0.55
0.62
0.90
1.20
0.30 2.3 3.4

0.27 2.5 3.7
0.28 2.4 3.6
21308 E
21309 E
21310 E
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
3.9370
23
25
27
0.9055
0.9843
1.0630
104 000
125 000
156 000
23 400
28 100
35 100
108 000
127 000
166 000
24 000
29 000
37 000
7 000
6 300
5 600
9 500
8 500
7 500
0.75
0.99
1.35
1.70
2.20
3.00
0.26 2.8 4.2

0.26 2.8 4.2
0.25 2.8 4.2
21311 E
21312 E
21313 E
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
29
31
33
1.1417
1.2205
1.2992
156 000
212 000
236 000
35 100
47 700
53 100
166 000
240 000
270 000
37 000
54 000
61 000
5 600
4 800
4 300
7 500
6 300
6 000
1.70
2.10
2.55
3.70
4.60
5.60
0.25 2.7 4.0

0.24 3.0 4.6
0.24 3.0 4.6
21314 E
21315 E
21316 E
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
35
37
39
1.3780
1.4567
1.5354
285 000
285 000
325 000
64 100
64 100
73 100
325 000
325 000
375 000
73 000
73 000
84 000
4 000
4 000
3 800
5 600
5 600
5 300
3.10
3.75
4.45
6.80
8.30
9.80
0.24 3.0 4.6

0.23 3.0 4.6
0.23 2.8 4.2
21317 E
21318 E
21319 E
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866
7.4803
7.8740
41
43
45
1.6142
1.6929
1.7717
325 000
380 000
425 000
73 100
85 400
95 500
375 000
450 000
490 000
84 000
101 000
110 000
3 800
3 600
3 400
5 300
4 800
4 500
5.20
6.10
7.05
11.50
13.40
15.50
0.23 2.8 4.2

0.23 2.8 4.2
0.23 2.8 4.2
21320 E
100
3.9370
215
8.4646
47
1.8504
425 000
95 500
490 000
110 000
3 400
4 500
8.60
19.00
0.22 2.8 4.2
146
Notes
146

Series: 22205 E 22256 CC/W33
Size: 25 mm 280 mm
0.9843 in 11.0236 in
Cylindrical bore
Designation
Tapered bore
CC design
E design
Bore
d
mm
in
Outside diameter
D
mm
in
CAC & ECA

design
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Mass
Calculation
factors
Reference Limiting
speed
speed
r/min r/min
kg
lb
e
-
Y1
-
Y2
-
22205 E
22206 E
22207 E
25
30
35
0.9843
1.1811
1.3780
52
62
72
2.0472
2.4409
2.8346
18
20
23
0.7087
0.7874
0.9055
49 000
64 000
86 500
11 000
14 400
19 400
44 000
60 000
85 000
10 000
13 000
19 000
13 000 17 000
10 000 14 000
9 000 12 000
0.26
0.29
0.45
0.60
0.60
1.00
0.35
0.33
0.31
1.9
2.2
2.2
2.9
3.3
3.3
22208 E
22209 E
22210 E
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1500
3.3465
3.5433
23
23
23
0.9055
0.9055
0.9055
96 500
102 000
104 000
21 700
22 900
23 400
90 000
98 000
108 000
20 000
22 000
24 000
8 000 11 000
7 500 10 000
7 000 9 500
0.53
0.58
0.63
1.20
1.30
1.40
0.28
0.26
0.24
2.4
2.6
2.8
3.6
3.9
4.2
22211 E
22212 E
22213 E
55
60
65
2.1654
2.3622
2.5591
100
110
120
3.9370
4.3307
4.7244
25
28
31
0.9843
1.1024
1.2205
125 000
156 000
193 000
28 100
35 100
43 400
127 000
166 000
216 000
29 000
37 000
49 000
6 300
5 600
5 000
8 500
7 500
7 000
0.84
1.15
1.55
1.90
2.50
3.40
0.24
0.24
0.25
2.8
2.8
2.8
4.2
4.2
4.2
22214 E
22215 E
22216 E
70
75
80
2.7559
2.9528
3.1496
125
130
140
4.9213
5.1181
5.5118
31
31
33
1.2205
1.2205
1.2992
208 000
212 000
236 000
46 800
47 700
53 100
228 000
240 000
270 000
51 000
54 000
61 000
5 000
4 800
4 300
6 700
6 300
6 000
1.55
1.70
2.10
3.40
3.70
4.60
0.23
0.22
0.22
2.9
3.0
3.0
4.4
4.6
4.6
22217 E
22218 E
22219 E
85
90
95
3.3465
3.5433
3.7402
150
160
170
5.9055 36.0
6.2992 40.0
6.6929 43.0
1.4173
1.5748
1.6929
245 000
290 000
320 000
55 100
65 200
71 900
275 000
340 000
375 000
62 000
76 000
84 000
3 800
3 400
3 200
5 600
5 300
5 000
2.55
3.25
4.00
5.60
7.20
8.80
0.22
0.23
0.24
3.0
2.9
2.8
4.6
4.4
4.2
22220 E
22222 E
22224 E
100
110
120
3.9370
4.3307
4.7244
180
200
215
7.0866 46.0
7.8740 53.0
8.4646 58.0
1.8110
2.0866
2.2835
360 000
465 000
540 000
80 900
104 500
121 400
415 000
560 000
670 000
93 000
126 000
151 000
3 000
2 800
2 600
4 500
4 300
3 800
4.90
7.00
8.86
10.80
15.40
19.50
0.24
0.25
0.25
2.8
2.7
2.7
4.2
4.0
4.0
22226 E
130
22228 E
140
22230 CC/W33 150
5.1181
5.5118
5.9055
230
250
270
9.0551
9.8425
10.6299
64
68
73
2.5197
2.6772
2.8740
630 000
710 000
850 000
141 600
159 600
192 000
800 000
900 000
1 080 000
180 000
202 000
243 000
2 400
2 400
2 200
3 600
3 200
3 000
11.00
14.00
18.00
24.30
30.90
39.70
0.26
0.26
0.26
2.6
2.6
2.6
3.9
3.9
3.9
22232 CC/W33 160

22234 CC/W33 170
22236 CC/W33 180
6.2992
6.6929
7.0866
290
310
320
11.4173
12.2047
12.5984
80
86
86
3.1496
3.3858
3.3858
1 000 000
1 120 000
1 180 000
225 000
252 000
266 000
1 290 000
1 460 000
1 560 000
290 000
328 000
351 000
2 000
1 900
1 800
2 800
2 600
2 600
22.50
28.50
29.50
49.60
62.80
65.00
0.26
0.27
0.26
2.6
2.5
2.6
3.9
3.7
3.9
22238 CC/W33 190

22240 CC/W33 200
22244 CC/W33 220
7.4803
7.8740
8.6614
340
360
400
13.3858 92
14.1732 98
15.7480 108
3.6220
3.8583
4.2520
1 270 000
1 460 000
1 760 000
286 000
329 000
396 000
1 700 000
1 930 000
2 360 000
382 000
434 000
531 000
1 700
1 600
1 500
2 400
2 200
2 000
36.50
43.50
60.50
80.50
95.90
133.40
0.26
0.26
0.27
2.6
2.6
2.5
3.9
3.9
3.7
22248 CC/W33 240 9.4488

22252 CAC/W33 260 10.2362
22256 CC/W33 280 11.0236
440
480
500
17.3228 120
18.8976 130
19.6850 130
4.7244
5.1181
5.1181
2 200 000
2 650 000
2 700 000
495 000
596 000
607 000
3 000 000
3 550 000
3 750 000
674 000
798 000
843 000
1 300
1 200
1 100
1 800
1 600
1 500
83.00
110.00
115.00
183.00
242.50
253.50
0.27
0.27
0.26
2.5
2.5
2.6
3.7
3.7
3.9
147

SKF Explorer
Series: 22260 CC/W33 22272 CA/W33
Size: 280 mm 360 mm
11.0236 in 14.1732 in
Cylindrical bore
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
22260 CC/W33 280 11.0236 540

22264 CC/W33 320 12.5984 580
22272 CA/W33 360 14.1732 650
Basic load ratings

Width
B
mm
in
21.2598 140
22.8346 150
25.5906 170
5.5118
5.9055
6.6929
Dynamic
C
N
3 150 000
3 600 000
4 300 000
Speed rating
Static
C0
lbf
709 000
810 000
967 000
lbf
4 250 000
955 000
4 900 000 1 102 000
6 200 000 1 394 000
CAC & ECA

design
Tapered bore
Reference Limiting
speed
speed
r/min r/min
1 000
950
630
1 400
1 300
850
Mass
kg
Calculation
factors
lb
Y1
-
Y2
-
145.00 319.70 0.26 2.6 3.9

175.00 385.80 0.26 2.6 3.9
255.00 562.20 0.26 2.6 3.9
148
e
-

Series: 22308 E 22380 CA/W33
Size: 40 mm 400 mm
1.5748 in 15.7480 in
Cylindrical bore
Designation
Tapered bore
CC design
E design
Bore
d
mm
in
Outside diameter
D
mm
in
CAC & ECA

design
Basic load ratings

Width
B
mm
in
Dynamic
C
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
Calculation
factors
kg
lb
e
-
Y1
-
Y2
-
22308 E
22309 E
22310 E
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
3.9370
33
36
40
1.2992
1.1473
1.5748
150 000
183 000
220 000
33 700
41 100
49 500
140 000
183 000
224 000
31 000
41 000
50 000
6 000
5 300
4 800
8 000
7 000
6 300
1.05
1.40
1.90
2.30
3.10
4.20
0.37
0.37
0.37
1.8
1.8
1.8
2.7
2.7
2.7
22311 E
22312 E
22313 E
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
43
46
48
1.6929
1.8110
1.8898
270 000
310 000
340 000
60 700
69 700
76 400
280 000
335 000
360 000
63 000
75 000
81 000
4 300
4 000
3 800
5 600
5 300
5 000
2.45
3.10
3.75
5.40
6.80
8.30
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
22314 E
22315 E
22316 E
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
51
55
58
2.0079
2.1654
2.2835
355 000
400 000
430 000
79 800
89 900
96 700
380 000
430 000
455 000
85 000
97 000
102 000
3 200
3 000
2 800
4 500
4 300
4 000
4.30
5.25
6.20
9.50
11.60
13.70
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
22317 E
22318 E
22319 E
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866 60.0
7.4803 64.0
7.8740 67.0
2.3622
2.5197
2.6378
480 000
550 000
600 000
107 900
123 600
134 900
520 000
610 000
670 000
117 000
137 000
151 000
2 600
2 400
2 400
3 800
3 600
3 400
7.25
8.60
10.00
16.00
19.00
22.00
0.33
0.35
0.35
2.0
1.9
1.9
3.0
2.9
2.9
22320 E
22322 E
22324 CC/W33
100
110
120
3.9370
4.3307
4.7244
215
240
260
8.4646 73.0
9.4488 80.0
10.2362 86.0
2.8740
3.1496
3.3858
720 000
830 000
965 000
161 900
186 600
216 900
800 000
965 000
1 120 000
180 000
217 000
252 000
2 200
2 000
2 000
3 200
2 800
2 600
13.00
18.00
23.00
28.70
39.70
50.70
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
22326 CC/W33
22328 CC/W33
22330 CC/W33
130
140
150
5.1181
5.5118
5.9055
280
300
320
11.0236 93
11.8110 102
12.5984 108
3.6614
4.0157
4.2520
1 120 000
1 290 000
1 460 000
252 000
290 000
329 000
1 320 000
1 560 000
1 760 000
297 000
351 000
396 000
1 800
1 700
1 600
2 400
2 200
2 000
29.00
36.50
43.50
63.90
80.50
95.90
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
22332 CC/W33
22334 CC/W33
22336 CC/W33
160
170
180
6.2992
6.6929
7.0866
340
360
380
13.3858 114
14.1732 120
14.9606 126
4.4882
4.7244
4.9606
1 600 000
1 760 000
2 000 000
360 000
396 000
450 000
1 960 000
2 160 000
2 450 000
441 000
486 000
551 000
1 500
1 400
1 300
1 900
1 800
1 700
52.00
61.00
71.50
114.60
134.50
157.60
0.35
0.33
0.35
1.9
2.0
1.9
2.9
3.0
2.9
22338 CC/W33
22340 CC/W33
22344 CC/W33
190
200
220
7.4803
7.8740
8.6614
400
420
460
15.7480 132
16.5354 138
18.1102 145
5.1969
5.4331
5.7087
2 120 000
2 320 000
2 700 000
477 000
522 000
607 000
2 650 000
2 900 000
3 450 000
596 000
652 000
780 000
1 200
1 200
1 000
1 600
1 500
1 400
82.50
95.00
120.00
181.90
209.40
264.60
0.35
0.33
0.31
1.9
2.0
2.2
2.9
3.0
3.3
22348 CC/W33
22352 CC/W33
22356 CC/W33
240 9.4488
260 10.2362
280 11.0236
500
540
580
19.6850 155
21.2598 165
22.8346 175
6.1024
6.4961
6.8898
3 100 000
3 550 000
4 000 000
697 000
799 000
900 000
4 000 000
900 000
4 550 000 1 030 000
5 200 000 1 170 000
950
850
800
1 300
1 100
1 100
155.00
190.00
235.00
341.70
418.90
518.10
0.31
0.31
0.30
2.2
2.2
2.3
3.3
3.3
3.4
22380 CA/W33 400 15.7480
820
32.2835 243
9.5669
7 500 000 1 686 000 10 400 000 2 340 000
430
750
650.00
1433.00
0.30
2.3
3.4
149

Series: 23022 CC/W33 230/670 CA/W33
Size: 110 mm 670 mm
4.3307 in 26.3780 in
Cylindrical bore
Designation
Bore
d
Outside diameter
D
mm
in
Tapered bore
Basic load ratings

Width
B
mm
in
mm
in
23022 CC/W33
23024 CC/W33
23026 CC/W33
110
120
130
4.3307
4.7244
5.1181
170
180
200
6.6929
7.0866
7.8740
45
46
52
23028 CC/W33
23030 CC/W33
23032 CC/W33
140
150
160
5.5118
5.9055
6.2992
210
225
240
8.2677
8.8583
9.4488
23034 CC/W33
23036 CC/W33
23038 CC/W33
170
180
190
6.6929
7.0866
7.4803
260
280
290
23040 CC/W33
23044 CC/W33
23048 CC/W33
200
220
240
7.8740
8.6614
9.4488
23052 CC/W33
23056 CAC/W33
23060 CAC/W33
Dynamic
C
CC design
Speed rating
Static
C0
Reference Limiting
speed
speed
r/min
r/min
CAC & ECA

design
Mass
Calculation
factors
Y1
-
Y2
-
8.40
9.30
13.20
0.23 2.9
0.22 3.0
0.23 2.9
4.4
4.6
4.4
6.55
7.95
9.70
14.40
17.50
21.40
0.22 3.0
0.22 3.0
0.22 3.0
4.6
4.6
4.6
2 800
2 600
2 400
13.00
17.00
18.00
28.70
37.50
39.70
0.23 2.9
0.24 2.8
0.23 2.9
4.4
4.2
4.4
1 800
1 600
1 500
2 200
2 000
1 900
23.30
30.50
33.50
51.40
67.20
73.90
0.24 2.8
0.24 2.8
0.23 2.9
4.2
4.2
4.4
580 000
650 000
780 000
1 300
1 300
1 200
1 700
1 600
1 500
48.50
52.50
71.50
106.90
115.70
157.60
0.23 2.9
0.23 2.9
0.23 2.9
4.4
4.4
4.4
3 800 000
4 550 000
4 800 000
860 000
1 030 000
1 080 000
1 100
1 000
950
1 400
1 300
1 200
78.00
105.00
110.00
172.00
231.50
242.50
0.23 2.9
0.24 2.8
0.23 2.9
4.4
4.2
4.4
652 000
731 000
765 000
5 000 000
5 700 000
6 000 000
1 130 000
1 290 000
1 350 000
900
750
600
1 200
1 100
1 100
115.00
144.50
155.00
253.50
318.60
341.70
0.22 3.0
0.23 2.9
0.22 3.0
4.6
4.4
4.6
821 000
877 000
877 000
6 550 000
6 950 000
6 800 000
1 480 000
1 570 000
1 530 000
560
560
530
1 000
950
950
180.00
205.00
215.00
396.80
451.90
474.00
0.22 3.0
0.22 3.0
0.21 3.2
4.6
4.6
4.8
6.5748
7.2835
7.6772
4 150 000
933 000
5 100 000 1 147 000
5 600 000 1 259 000
7 800 000
9 300 000
10 200 000
1 760 000
2 100 000
2 300 000
500
450
430
900
800
750
225.00
310.00
355.00
496.00
683.40
782.60
0.21 3.2
0.22 3.0
0.22 3.0
4.8
4.6
4.6
7.8740
8.3465
9.0551
6 000 000 1 349 000

6 700 000 1 507 000
7 650 000 1 720 000
11 400 000
12 500 000
14 600 000
2 570 000
2 810 000
3 290 000
400
380
340
700
670
600
405.00
485.00
600.00
892.90
1069.20
1322.80
0.22 3.0
0.22 3.2
0.21 3.2
4.6
4.8
4.8
lbf
lbf
kg
1.7717
1.8110
2.0472
310 000
355 000
430 000
70 000
80 000
97 000
440 000
510 000
610 000
100 000
120 000
140 000
3 400
3 200
2 800
4 300
4 000
3 600
3.80
4.20
6.00
53
56
60
2.0866
2.2047
2.3622
465 000
510 000
585 000
105 000
115 000
132 000
680 000
750 000
880 000
160 000
170 000
200 000
2 600
2 400
2 400
3 400
3 200
3 000
10.2362
11.0236
11.4173
67
74
75
2.6378
2.9134
2.9528
710 000
830 000
865 000
160 000
187 000
195 000
1 060 000
1 250 000
1 340 000
240 000
290 000
310 000
2 200
2 000
1 900
310
340
360
12.2047
13.3858
14.1732
82
90
92
3.2283
3.5433
3.6220
1 000 000
1 220 000
1 290 000
225 000
275 000
290 000
1 530 000
1 860 000
2 080 000
350 000
420 000
470 000
260 10.2362
280 11.0236
300 11.8110
400
420
460
15.7480
16.5354
18.1102
104
106
118
4.0945
4.1732
4.6457
1 600 000
1 730 000
2 120 000
360 000
389 000
477 000
2 550 000
2 850 000
3 450 000
23064 CC/W33
23068 CAC/W33
23072 CAC/W33
320 12.5984
340 13.3858
360 14.1732
480
520
540
18.8976
20.4724
21.2598
121
133
134
4.7638
5.2362
5.2756
2 240 000
2 700 000
2 750 000
504 000
607 000
619 000
23076 CAC/W33
23080 CAC/W33
23084 CA/W33
380 14.9606
400 15.7480
420 16.5354
560
600
620
22.0472
23.6220
24.4094
135
148
150
5.3150
5.8268
5.9055
2 900 000
3 250 000
3 400 000
23088 CA/W33
23092 CA/W33
23096 CA/W33
440 17.3228
460 18.1102
480 18.8976
650
680
700
25.5906
26.7717
27.5591
157
163
165
6.1811
6.4173
6.4961
3 650 000
3 900 000
3 900 000
230/500 CA/W33
230/530 CA/W33
230/560 CA/W33
500 19.6850
530 20.8661
560 22.0472
720
780
820
28.3465
30.7087
32.2835
167
185
195
230/600 CA/W33
230/630 CA/W33
230/670 CA/W33
600 23.6220
630 24.8031
670 26.3780
870
920
980
34.2520
36.2205
38.5827
200
212
230
lb
150
e
-

Series: 230/710 CA/W33 230/1250 CAF/W33
27.9528 in 49.2126 in
Cylindrical bore
Designation
CAF & ECA

design
Tapered bore
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Mass
Reference Limiting
speed
speed
r/min
r/min
Calculation
factors
kg
lb
e
-
Y1
-
Y2
-
230/710 CA/W33
230/750 CA/W33
230/800 CA/W33
710 27.9528 1 030

750 29.5276 1 090
800 31.4961 1 150
40.5512 236 9.2913

42.9134 250 9.8425
45.2756 258 10.1575
8 300 000 1 866 000 16 300 000

9 650 000 2 170 000 18 600 000
10 000 000 2 248 000 20 000 000
3 670 000
4 190 000
4 500 000
320
300
280
560
530
480
670.00
795.00
895.00
1477.10
1752.70
1973.10
0.21
0.21
0.21
3.2
3.2
3.4
4.8
4.8
5.0
230/850 CA/W33
230/900 CA/W33
230/950 CA/W33
850 33.4646 1 220

900 35.4331 1 280
950 37.4016 1 360
48.0315 272 10.7087

50.3937 280 11.0236
53.5433 300 11.8110
9 370 000 2 107 000 21 600 000

10 100 000 2 271 000 23 200 000
12 000 000 2 698 000 28 500 000
4 860 000
5 220 000
6 410 000
240
220
200
450
400
380
1050.00
1200.00
1450.00
2314.80
2645.50
3196.70
0.20
0.20
0.20
3.4
3.4
3.4
5.0
5.0
5.0
1 000 39.3701 1 420

1 060 41.7323 1 500
1 250 49.2126 1 750
55.9055 308 12.1260

59.0551 325 12.7953
68.8976 375 14.7638
12 700 000 2 855 000 30 500 000 6 860 000

13 800 000 3 103 000 34 000 000 7 650 000
17 900 000 4 024 000 45 000 000 10 120 000
180
170
130
360
320
240
1600.00
2250.00
2840.00
3527.40
4960.40
6261.10
0.19
0.19
0.19
3.6
3.6
3.6
5.3
5.3
5.3
230/1000 CA/W33
230/1060 CAF/W33
230/1250 CAF/W33
151

Series: 23120 CC/W33 231/630 CA/W33
Size: 100 mm 630 mm
3.9370 in 24.8031 in
Cylindrical bore
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Tapered bore
Basic load ratings

Width
B
mm
in
Dynamic
C
CJ & CC
design
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed
speed
r/min
r/min
CAC & ECA

design
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
23120 CC/W33
23122 CC/W33
23124 CC/W33
100
110
120
3.9370
4.3307
4.7244
165
180
200
6.4961
7.0866
7.8740
52
56
62
2.0472
2.2047
2.4409
365 000
430 000
510 000
82 100
96 700
114 600
490 000
585 000
695 000
111 000
132 000
157 000
3 000
2 800
2 600
4 000
3 600
3 400
4.55
5.75
8.00
10.00
12.70
17.60
0.30
0.30
0.28
2.3
2.3
2.4
3.4
3.4
3.6
23126 CC/W33
23128 CC/W33
23130 CC/W33
130
140
150
5.1181
5.5118
5.9055
210
225
250
8.2677
8.8583
9.8425
64
68
80
2.5197
2.6772
3.1496
560 000
630 000
830 000
125 900
141 600
186 600
780 000
900 000
1 200 000
176 000
203 000
270 000
2 400
2 200
2 000
3 200
2 800
2 600
8.80
10.50
16.00
19.40
23.10
35.30
0.28
0.28
0.30
2.4
2.4
2.3
3.6
3.6
3.4
23132 CC/W33
23134 CC/W33
23136 CC/W33
160
170
180
6.2992
6.6929
7.0866
270
280
300
10.6299
11.0236
11.8110
86
88
96
3.3858
3.4646
3.7795
980 000
1 040 000
1 200 000
220 300
233 800
269 800
1 370 000
1 500 000
1 760 000
308 000
338 000
396 000
1 900
1 800
1 700
2 400
2 400
2 200
20.50
22.00
28.00
45.20
48.50
61.70
0.30
0.30
0.30
2.3
2.3
2.3
3.4
3.4
3.4
23138 CC/W33
23140 CC/W33
23144 CC/W33
190
200
220
7.4803
7.8740
8.6614
320
340
370
12.5984
13.3858
14.5669
104
112
120
4.0945
4.4094
4.7244
1 370 000
1 600 000
1 800 000
308 000
359 700
404 600
2 080 000
2 360 000
2 750 000
468 000
531 000
619 000
1 500
1 500
1 300
2 000
1 900
1 700
35.00
43.00
53.50
77.20
94.80
117.90
0.31
0.31
0.30
2.2
2.2
2.3
3.3
3.3
3.4
23148 CC/W33 240 9.4488

23152 CC/W33 260 10.2362
23156 CAC/W33 280 11.0236
400
440
460
15.7480
17.3228
18.1102
128
144
146
5.0394
5.6693
5.7480
2 080 000
2 550 000
2 650 000
467 600
573 200
595 700
3 200 000
3 900 000
4 250 000
720 000
877 000
956 000
1 200
1 100
1 000
1 600
1 400
1 300
66.50
90.50
97.00
146.60
199.50
213.80
0.30
0.31
0.30
2.3
2.2
2.3
3.4
3.3
3.4
23160 CC/W33
23164 CC/W33
23168 CC/W33
300 11.8110
320 12.5984
340 13.3858
500
540
580
19.6850
21.2598
22.8346
160
176
190
6.2992
6.9291
7.4803
3 200 000
3 750 000
4 250 000
719 400
843 000
955 400
5 100 000
6 000 000
6 800 000
1 147 000
1 349 000
1 529 000
950
850
800
1 200
1 100
1 000
125.00
165.00
210.00
275.60
363.80
463.00
0.30
0.31
0.31
2.3
2.2
2.2
3.4
3.3
3.3
23172 CC/W33
23176 CA/W33
23180 CA/W33
360 14.1732
380 14.9606
400 15.7480
600
620
650
23.6220
24.4094
25.5906
192
194
200
7.5591
7.6378
7.8740
4 300 000
966 600
4 400 000
989 100
4 650 000 1 045 300
6 950 000
7 100 000
7 650 000
1 563 000
1 597 000
1 720 000
700
560
530
1 000
1 000
950
216.20
230.00
265.00
476.60
507.10
584.20
0.30
0.30
0.28
2.3
2.3
2.4
3.4
3.4
3.6
23184 CJ/W33
23188 CA/W33
23192 CA/W33
420 16.5354
440 17.3228
460 18.1102
700
720
760
27.5591
28.3465
29.9213
224
226
240
8.8189
8.8976
9.4488
5 600 000 1 258 900

6 000 000 1 348 800
6 400 000 1 438 700
9 300 000
10 000 000
10 800 000
2 091 000
2 248 000
2 428 000
480
450
430
900
850
800
350.00
360.00
440.00
771.60
793.70
970.00
0.30
0.30
0.30
2.3
2.3
2.3
3.4
3.4
3.4
23196 CA/W33 480 18.8976

231/500 CA/W33 500 19.6850
231/530 CA/W33 530 20.8661
790
830
870
31.1024
32.6772
34.2520
248
264
272
9.7638
10.3937
10.7087
6 950 000 1 562 400

7 650 000 1 719 700
8 150 000 1 832 100
12 000 000
12 900 000
14 000 000
2 698 000
2 900 000
3 148 000
400
380
360
750
700
670
485.00
580.00
645.00
1069.20
1278.70
1422.00
0.30
0.30
0.30
2.3
2.3
2.3
3.4
3.4
3.4
231/560 CA/W33 560 22.0472

920
231/600 CA/W33 600 23.6220
980
231/630 CA/W33 630 24.8031 1 030
36.2205
38.5827
40.5512
280
300
315
11.0236
11.8110
12.4016
9 150 000 2 056 900

10 200 000 2 293 000
10 500 000 2 360 000
16 000 000
18 000 000
20 800 000
3 597 000
4 047 000
4 676 000
340
320
260
630 740.00
560 895.00
530 1050.00
1631.40
1973.10
2314.80
0.30
0.30
0.30
2.3
2.3
2.3
3.4
3.4
3.4
152
Standard
Series: 231/670 CA/W33 231/1000 CAF/W33
26.3780 in 39.3701 in
Cylindrical bore
Designation
CA & CAF
design
Tapered bore
Bore
Outside diameter
d
D
mm
in
mm
in
231/670 CA/W33
231/710 CA/W33
231/750 CA/W33
231/800 CA/W33
231/850 CA/W33
231/1000 CAF/W33
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Mass
Reference Limiting
speed
speed
r/min r/min
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
670 26.3780 1 090

710 27.9528 1 150
750 29.5276 1 220
42.9134 336 13.2283

45.2756 345 13.5827
48.0315 365 14.3701
10 900 000 2 450 000 22 400 000

12 200 000 2 743 000 26 000 000
13 800 000 3 102 000 29 000 000
5 040 000
5 845 000
6 520 000
240
240
220
500
450
430
1250.00
1450.00
1700.00
2755.80
3196.70
3747.80
0.30
0.28
0.28
2.3
2.4
2.4
3.4
3.6
3.6
800 31.4961 1 280

850 33.4646 1 360
1 000 39.3701 1 580
50.3937 375 14.7638

53.5433 400 15.7480
62.2047 462 18.1890
14 800 000 3 327 000 31 500 000 7 082 000

16 100 000 3 619 000 34 500 000 7 756 000
21 400 000 4 811 000 48 000 000 10 790 000
200
180
140
400
360
280
1920.00
2200.00
3500.00
4232.80
4850.10
7716.10
0.28
0.28
0.28
2.4
2.4
2.4
3.6
3.6
3.6
153

Series: 23218 CC/W33 232/600 CA/W33
Size: 90 mm 600 mm
3.5433 in 23.6220 in
Cylindrical bore
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Tapered bore
Basic load ratings

Width
B
mm
in
Dynamic
C
CC design
Speed rating
Static
C0
lbf
lbf
CA & CAC
design
Mass
Reference Limiting
speed
speed
r/min
r/min
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
23218 CC/W33
23220 CC/W33
23222 CC/W33
90
100
110
3.5433
3.9370
4.3307
160
180
200
6.2992
7.0866
7.8740
52.4
60.3
69.8
2.0630
2.3740
2.7480
355 000
475 000
600 000
80 000
107 000
135 000
440 000
600 000
765 000
99 000
135 000
172 000
2 800 3 800
2 400 3 400
2 200 3 200
4.65
6.85
9.85
10.30
15.10
21.70
0.31
0.33
0.33
2.2
2.0
2.0
3.3
3.0
3.0
23224 CC/W33
23226 CC/W33
23228 CC/W33
120
130
140
4.7244
5.1181
5.5118
215
230
250
8.4646
9.0551
9.8425
76
80
88
2.9921
3.1496
3.4646
695 000
780 000
915 000
156 000
175 000
206 000
930 000
1 060 000
1 250 000
210 000
239 000
281 000
2 000 2 800
1 900 2 600
1 700 2 400
12.00
14.50
19.00
26.50
32.00
41.90
0.35
0.33
0.33
1.9
2.0
2.0
2.9
3.0
3.0
23230 CC/W33
23232 CC/W33
23234 CC/W33
150
160
170
5.9055
6.2992
6.6929
270
290
310
10.6299
11.4173
12.2047
96
104
110
3.7795
4.0945
4.3307
1 080 000
1 220 000
1 400 000
243 000
274 000
315 000
1 460 000
1 660 000
1 930 000
329 000
374 000
434 000
1 600 2 200
1 500 2 200
1 400 2 000
24.50
31.00
37.50
54.00
68.30
82.70
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23236 CC/W33
23238 CC/W33
23240 CC/W33
180
190
200
7.0866
7.4803
7.8740
320
340
360
12.5984
13.3858
14.1732
112
120
128
4.4094
4.7244
5.0394
1 500 000
1 660 000
1 860 000
337 000
373 000
418 000
2 120 000
2 400 000
2 700 000
477 000
540 000
607 000
1 300 1 900
1 300 1 800
1 200 1 700
39.50
48.00
58.00
87.10
105.80
127.90
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23244 CC/W33 220 8.6614

23248 CC/W33 240 9.4488
23252 CAC/W33 260 10.2362
400
440
480
15.7480
17.3228
18.8976
144
160
174
5.6693
6.2992
6.8504
2 360 000
2 900 000
2 820 000
531 000
652 000
634 000
3 450 000
4 300 000
4 750 000
776 000
967 000
1 068 000
1 100 1 500
950 1 300
800 1 200
81.50
110.00
140.00
179.70
242.50
308.60
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23256 CAC/W33 280 11.0236

23260 CAC/W33 300 11.8110
23264 CAC/W33 320 12.5984
500
540
580
19.6850
21.2598
22.8346
176
192
208
6.9291
7.5591
8.1890
2 820 000
3 340 000
3 850 000
634 000
751 000
865 000
4 900 000
5 850 000
6 700 000
1 102 000
1 316 000
1 507 000
750 1 100
670 1 000
630
950
150.00
190.00
240.00
330.70
418.90
529.10
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23268 CA/W33
23272 CA/W33
23276 CA/W33
340 13.3858
360 14.1732
380 14.9606
620
650
680
24.4094
25.5906
26.7717
224
232
240
8.8189
9.1339
9.4488
5 100 000
5 400 000
5 850 000
1 146 000
1 214 000
1 315 000
7 800 000
8 300 000
9 150 000
1 754 000
1 866 000
2 057 000
560
530
500
800
750
750
295.00
335.00
375.00
650.40
738.50
826.70
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23280 CA/W33
23284 CA/W33
23288 CA/W33
400 15.7480
420 16.5354
440 17.3228
720
760
790
28.3465
29.9213
31.1024
256
272
280
10.0787
10.7087
11.0236
6 550 000
7 350 000
7 800 000
1 472 000
1 652 000
1 753 000
10 400 000
11 600 000
12 500 000
2 338 000
2 608 000
2 810 000
480
450
430
670
630
600
450.00
535.00
590.00
992.10
1179.50
1300.70
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
23292 CA/W33 460 18.1102

23296 CA/W33 480 18.8976
232/500 CA/W33 500 19.6850
830
870
920
32.6772
34.2520
36.2205
296
310
336
11.6535 8 500 000

12.2047 9 300 000
13.2283 10 600 000
1 911 000
2 091 000
2 383 000
13 700 000
15 000 000
17 300 000
3 080 000
3 372 000
3 890 000
400
380
360
560
530
500
695.00
800.00
985.00
1532.20
1763.70
2171.50
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
232/530 CA/W33 530 20.8661

980
232/560 CA/W33 560 22.0472 1 030
232/600 CA/W33 600 23.6220 1 090
38.5827
40.5512
42.9134
355
365
388
13.9764 11 100 000

14.3701 11 500 000
15.2756 13 100 000
2 495 000
2 585 000
2 945 000
20 400 000
22 000 000
25 500 000
4 586 000
4 946 000
5 733 000
300
280
260
480
430
400
1200.00
1350.00
1600.00
2645.50
2976.20
3527.40
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
154
Standard
Series: 232/670 CA/W33 232/750 CAF/W33
Size: 670 mm 750 mm
26.3780 in 29.5276 in
Series: 238/500 CAMA/W20 238/1180 CAFA/W20
19.6850 in 46.4567 in
Cylindrical bore
Tapered bore
Designation
CA, CAF, CACMA & CAFA

design
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
17.2441 15 400 000

17.7165 17 600 000
18.7008 18 700 000
Speed rating
Static
C0
lbf
232/670 CA/W33
232/710 CA/W33
232/750 CAF/W33
670
710
750
26.3780 1 220
27.9528 1 280
29.5276 1360
48.0315 438
50.3937 450
53.5433 475
238/500 CAMA/W20
238/630 CAMA/W20
238/670 CAMA/W20
500
630
670
19.6850
24.8031
26.3780
620
780
820
24.4094 90
30.7087 112
32.2835 112
3.5433
4.4094
4.4094
1 480 000
2 190 000
2 250 000
333 000
492 000
506 000
238/710 CAMA/W20
238/750 CAMA/W20
238/850 CAMA/W20
710
750
850
27.9528
870
29.5276
920
33.4646 1 030
34.2520 118
36.2205 128
40.5512 136
4.6457
5.0394
5.3543
238/1000 CAMA/W20 1 000

238/1060 CAMA/W20 1 060
238/1180 CAFA/W20 1 180
39.3701 1 220
41.7323 1 280
46.4567 1 420
48.0315 165
50.3937 165
55.9055 180
6.4961
6.4961
7.0866
3 462 000 30 500 000

3 956 000 34 500 000
4 204 000 36 500 000
lbf
Reference Limiting
speed
speed
r/min r/min
Mass
kg
360 2270.00
320 2610.00
300 3050.00
Calculation
factors
lb
e
-
Y1
-
Y2
-
5004.40
5754.00
6724.00
0.35
0.35
0.35
1.9
1.9
1.9
2.9
2.9
2.9
6 857 000
7 756 000
8 206 000
220
200
190
4 000 000
6 100 000
6 400 000
900 000
1 370 000
1 440 000
530 1 000
400 750
360 700
62.00
120.00
130.00
136.70
264.60
286.60
0.12
0.12
0.11
5.6
5.6
6.1
8.4
8.4
9.1
2 580 000
2 930 000
3 340 000
580 000 7 500 000

659 000 8 500 000
751 000 10 000 000
1 690 000
1 910 000
2 250 000
340
320
260
670
600
530
153.00
180.00
240.00
337.30
396.80
529.10
0.11
0.11
0.11
6.1
6.1
6.1
9.1
9.1
9.1
4 660 000
4 770 000
5 870 000
1 048 000 14 300 000

1 072 000 15 000 000
1 320 000 18 600 000
3 210 000
3 370 000
4 180 000
220
200
170
400
380
320
410.00
435.00
575.00
903.90
959.00
1267.60
0.12
0.11
0.11
5.6
6.1
6.1
8.4
9.1
9.1
155

Series: 23926 CAM2/W33 239/900 CA/W33
Size: 130 mm 900 mm
5.1181 in 35.4331 in
Cylindrical bore
Designation
Bore
Outside diameter
d
D
mm
in
mm
in
Tapered bore
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
CC design
lbf
Reference Limiting
speed
speed
r/min
r/min
CA & CAC
design
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
23926 CAM2/W33
23932 CAM2/W33
23936 CC/W33
130
160
180
5.1181
6.2992
7.0866
180
220
250
7.0866
8.6614
9.8425
37
45
52
1.4567
1.7717
2.0472
202 000
299 000
431 000
45 000
67 000
97 000
360 000
570 000
830 000
80 000 3 200
130 000 2 600
190 000 2 200
4 000
3 300
2 800
2.95
5.20
7.90
6.50
11.50
17.40
0.18
0.17
0.18
3.8
4.0
3.8
5.6
5.9
5.6
23938 CC/W33
23940 CC/W33
23944 CC/W33
190
200
220
7.4803
7.8740
8.6614
260
280
300
10.2362
11.0236
11.8110
52
60
60
2.0472
2.3622
2.3622
414 000
546 000
546 000
93 000
123 000
123 000
800 000
1 040 000
1 080 000
180 000 2 200

230 000 2 000
240 000 1 900
2 600
2 400
2 200
8.30
11.50
12.50
18.30
25.40
27.60
0.16
0.19
0.16
4.2
3.6
4.2
6.3
5.3
6.3
23948 CC/W33
23952 CC/W33
23956 CC/W33
240
260
280
9.4488
10.2362
11.0236
320
360
380
12.5984
14.1732
14.9606
60
75
75
2.3622
2.9528
2.9528
564 000
880 000
845 000
127 000
198 000
190 000
1 160 000
1 800 000
1 760 000
260 000 1 700

400 000 1 500
400 000 1 400
2 000
1 900
1 700
13.50
23.50
25.00
29.80
51.80
55.10
0.15
0.18
0.16
4.5
3.8
4.2
6.7
5.6
6.3
23960 CC/W33
23964 CC/W33
23968 CC/W33
280
320
340
11.0236
12.5984
13.3858
420
440
460
16.5354
17.3228
18.1102
90
90
90
3.5433
3.5433
3.5433
1 200 000
1 430 000
1 460 000
270 000
321 000
328 000
2 500 000
2 700 000
2 800 000
560 000 1 300

610 000 1 400
630 000 1 300
1 600
1 500
1 400
39.50
42.00
45.50
87.10
92.60
100.30
0.19
0.18
0.17
3.6
4.0
4.0
5.3
5.9
5.9
23972 CC/W33
23976 CC/W33
23980 CC/W33
360
380
400
14.1732
14.9606
15.7480
480
520
540
18.8976 90
20.4724 106
21.2598 106
3.5433
4.1732
4.1732
1 400 000
1 960 000
2 000 000
315 000
441 000
450 000
2 750 000
3 800 000
3 900 000
620 000 1 200

850 000 1 100
880 000 1 100
1 300
1 200
1 200
46.00
69.00
71.00
101.40
152.10
156.50
0.16
0.17
0.17
4.5
4.0
4.2
6.7
5.9
6.3
23984 CC/W33
23988 CC/W33
23992 CA/W33
420
440
460
16.5354
17.3228
18.1102
560
600
620
22.0472 106
23.6220 118
24.4094 118
4.1732
4.6457
4.6457
2 040 000
2 450 000
2 500 000
459 000
551 000
562 000
4 150 000
4 900 000
5 000 000
930 000 1 000

1 100 000
950
1 120 000
600
1 100
1 000
1 000
74.50
99.50
105.00
164.20
219.40
231.50
0.16
0.17
0.16
4.2
4.2
4.2
6.3
6.3
6.3
23996 CA/W33
239/500 CA/W33
239/530 CA/W33
480
500
530
18.8976
19.6850
20.8661
650
670
710
25.5906 128
26.3780 128
27.9528 136
5.0394
5.0394
5.3543
2 900 000
2 900 000
3 200 000
652 000
652 000
719 000
5 700 000
6 000 000
6 700 000
1 280 000
1 350 000
1 510 000
560
530
500
1 000
950
900
125.00
130.00
155.00
275.60
286.60
341.70
0.18
0.17
0.17
3.8
4.0
4.0
5.6
5.9
5.9
239/560 CA/W33
239/600 CA/W33
239/630 CA/W33
560
600
630
22.0472
23.6220
24.8031
750
800
850
29.5276 140
31.4961 150
33.4646 165
5.5118
5.9055
6.4961
3 450 000
776 000
3 900 000
877 000
4 650 000 1 045 000
7 200 000
8 300 000
9 800 000
1 620 000
1 870 000
2 200 000
450
430
400
850
750
700
175.00
220.00
280.00
385.80
485.00
617.30
0.16
0.17
0.17
4.2
4.0
4.0
6.3
5.9
5.9
239/670 CA/W33
239/710 CA/W33
239/750 CA/W33
670
710
750
26.3780
900
27.9528
950
29.5276 1 000
35.4331 170
37.4016 180
39.3701 185
6.6929
7.0866
7.2835
5 000 000 1 124 000 10 800 000

5 600 000 1 259 000 12 000 000
6 000 000 1 349 000 13 200 000
2 430 000
2 700 000
2 970 000
360
340
320
670
600
560
315.00
365.00
420.00
694.40
804.70
925.90
0.17
0.17
0.16
4.0
4.0
4.2
5.9
5.9
6.3
239/800 CA/W33
239/850 CA/W33
239/900 CA/W33
800
850
900
31.4961 1 060
33.4646 1 120
35.4331 1 180
41.7323 195
44.0945 200
46.4567 206
7.6772
7.8740
8.1102
6 400 000 1 439 000 14 300 000

5 980 000 1 344 000 15 600 000
6 440 000 1 448 000 17 000 000
3 210 000
3 510 000
3 820 000
300
260
240
530
480
450
470.00
560.00
605.00
1036.20
1234.60
1333.80
0.16
0.16
0.15
4.2
4.2
4.5
6.3
6.3
6.7
156
Standard
Series: 239/950 CA/W33 239/1180 CAF/W33
37.4016 in 46.4567 in
Cylindrical bore
Designation
CA & CAF
design
Tapered bore
Bore
Outside diameter
d
D
mm
in
mm
in
239/950 CA/W33
239/1060 CAF/W33
239/1180 CAF/W33
950 37.4016 1 250

1 060 41.7323 1 400
1 180 46.4567 1 540
Basic load ratings

Width
B
mm
in
49.2126 224 8.8189

55.1181 250 9.8425
60.6299 272 10.7087
Dynamic
C
N
Speed rating
Static
C0
lbf
7 250 000 1 630 000 19 600 000

9 550 000 2 147 000 26 000 000
11 100 000 2 495 000 31 000 000
lbf
4 410 000
5 840 000
6 970 000
Reference Limiting
speed
speed
r/min
r/min
220
180
150
430
360
300
Mass
kg
755.00
1100.00
1400.00
Calculation
factors
lb
1664.50
2425.10
3086.40
e
-
0.15
0.16
0.16
Y1
-
Y2
-
4.5
4.2
4.2
6.7
6.3
6.3
157

Series: 24015 CC/W33 240/630 ECJ/W33
Size: 75 mm 630 mm
2.9528 in 24.8031 in
Cylindrical bore
Designation
Bore
Outside diameter
d
D
mm
in
mm
in
Tapered bore
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
ECJ & CC
design
lbf
Reference Limiting
speed
speed
r/min
r/min
CAC, ECA & ECAC

design
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
24015 CC/W33
24020 CDC/W33
24024 CC/W33
75
100
120
2.9528
3.9370
4.7244
115
150
180
4.5276
5.9055
7.0866
40
50
60
1.5748
1.9685
2.3622
173 000
248 000
430 000
38 900
55 800
96 700
232 000
415 000
670 000
50 000 3 800
90 000 2 600
150 000 2 400
5 300
4 000
3 400
1.55
2.94
5.45
3.40
6.50
12.00
0.28
0.28
0.30
2.4
2.4
2.3
3.6
3.6
3.4
24026 CC/W33
24028 CC/W33
24030 CC/W33
130
140
150
5.1181
5.5118
5.9055
200
210
225
7.8740
8.2677
8.8583
69
69
75
2.7165
2.7165
2.9528
540 000
570 000
655 000
121 400
128 100
147 200
815 000
900 000
1 040 000
180 000 2 000

200 000 2 000
230 000 1 800
3 000
2 800
2 600
8.05
8.55
10.50
17.70
18.80
23.10
0.31
0.30
0.30
2.2
2.3
2.3
3.3
3.4
3.4
24032 CC/W33
24034 CC/W33
24036 CC/W33
160
170
180
6.2992
6.6929
7.0866
240
260
280
9.4488 80
10.2362 90
11.0236 100
3.1496
3.5433
3.9370
750 000
930 000
1 080 000
168 600
209 000
243 000
1 200 000
1 460 000
1 730 000
270 000 1 700

330 000 1 600
390 000 1 300
2 400
2 400
2 200
13.00
17.50
23.00
28.70
38.60
50.70
0.30
0.33
0.33
2.3
2.0
2.0
3.4
3.0
3.0
24038 CC/W33
24040 CC/W33
24044 CC/W33
190
200
220
7.4803
7.8740
8.6614
290
310
340
11.4173 100
12.2047 109
13.3858 118
3.9370
4.2913
4.6457
1 120 000
1 290 000
1 560 000
252 000
290 000
351 000
1 800 000
2 120 000
2 600 000
400 000 1 400

480 000 1 300
580 000 1 200
2 000
1 900
1 700
24.50
31.00
40.00
54.00
68.30
88.20
0.31
0.33
0.33
2.2
2.0
2.0
3.3
3.0
3.0
24048 CC/W33
24052 CC/W33
24056 CC/W33
240
260
280
9.4488
10.2362
11.0236
360
400
420
14.1732 118
15.7480 140
16.5354 140
4.6457
5.5118
5.5118
1 600 000
2 040 000
2 160 000
360 000
459 000
486 000
2 700 000
3 450 000
3 800 000
610 000 1 100

780 000 1 000
850 000 950
1 600
1 400
1 400
43.00
65.50
69.50
94.80
144.40
153.20
0.30
0.33
0.31
2.3
2.0
2.2
3.4
3.0
3.3
24060 CC/W33
24064 CC/W33
24068 CC/W33
280
320
340
11.0236
12.5984
13.3858
460
480
520
18.1102 160
18.8976 160
20.4724 180
6.2992
6.2992
7.0866
2 700 000
2 850 000
3 450 000
607 000
641 000
776 000
4 750 000 1 070 000

5 100 000 1 150 000
6 200 000 1 390 000
850
800
750
1 200
1 200
1 100
97.00
100.00
140.00
213.80
220.50
308.60
0.33
0.31
0.33
2.0
2.2
2.0
3.0
3.3
3.0
24072 CC/W33
24076 CC/W33
24080 ECAC/W33
360
380
400
14.1732
14.9606
15.7480
540
560
600
21.2598 180
22.0472 180
23.6220 200
7.0866
7.0866
7.8740
3 550 000
3 600 000
3 740 000
798 000
809 000
841 000
6 550 000 1 470 000

6 800 000 1 530 000
8 000 000 1 800 000
700
670
560
1 000
950
780
145.00
150.00
205.00
319.70
330.70
451.90
0.31
0.30
0.30
2.2
2.3
2.3
3.3
3.4
3.4
24084 ECA/W33
24088 ECA/W33
24092 ECA/W33
420
440
460
16.5354
17.3228
18.1102
620
650
680
24.4094 200
25.5906 212
26.7717 218
7.8740
8.3465
8.5827
4 400 000
989 000 8 300 000 1 870 000
4 800 000 1 079 000 9 150 000 2 060 000
5 200 000 1 169 000 10 000 000 2 250 000
530
500
480
900
850
800
210.00
245.00
275.00
463.00
540.10
606.30
0.30
0.30
0.28
2.3
2.3
2.4
3.4
3.4
3.6
24096 ECA/W33
240/500 ECA/W33
240/530 ECA/W33
480
500
530
18.8976
19.6850
20.8661
700
720
780
27.5591 218
28.3465 218
30.7087 250
8.5827
8.5827
9.8425
5 300 000 1 191 000 10 400 000 2 340 000

5 500 000 1 236 000 11 000 000 2 470 000
6 700 000 1 506 000 13 200 000 2 970 000
450
430
400
750
700
670
285.00
295.00
410.00
628.30
650.40
903.90
0.28
0.26
0.28
2.4
2.6
2.4
3.6
3.9
3.6
240/560 ECA/W33
240/600 ECA/W33
240/630 ECJ/W33
560
600
630
22.0472
23.6220
24.8031
820
870
920
32.2835 258 10.1575

34.2520 272 10.7087
36.2205 290 11.4173
7 350 000 1 652 000 14 600 000 3 280 000

8 150 000 1 832 000 17 000 000 3 820 000
8 800 000 1 978 000 18 000 000 4 050 000
380
340
320
630
560
530
465.00 1025.10
520.00 1146.40
645.00 1422.00
0.28
0.30
0.28
2.4
2.3
2.4
3.6
3.4
3.6
158

Series: 240/670 ECA/W33 240/1120 CAF/W33
26.3780 in 44.0945 in
Cylindrical bore
Designation
CAF & ECA

design
Tapered bore
Bore
Outside diameter
d
D
mm
in
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Mass
Reference Limiting
speed
speed
r/min r/min
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
240/670 ECA/W33
240/710 ECA/W33
240/750 ECA/W33
670 26.3780 980

710 27.9528 1 030
750 29.5276 1 090
38.5827 308 12.1260 10 000 000 2 248 000 20 400 000

40.5512 315 12.4016 9 370 000 2 106 000 22 800 000
42.9134 335 13.1890 10 100 000 2 270 000 25 000 000
4 590 000
5 130 000
5 620 000
300
260
240
500
450
430
790.00 1741.60
895.00 1973.10
1065.00 2347.90
0.28
0.27
0.28
2.4
2.5
2.4
3.6
3.7
3.6
240/800 ECA/W33
240/850 ECA/W33
240/900 ECA/W33
800 31.4961 1 150

850 33.4646 1 220
900 35.4331 1 280
45.2756 345 13.5827 11 100 000 2 495 000 28 500 000

48.0315 365 14.3701 12 700 000 2 855 000 31 500 000
50.3937 375 14.7638 13 600 000 3 057 000 34 500 000
6 410 000
7 080 000
7 760 000
220
200
190
400
360
340
1200.00 2645.50
1410.00 3108.50
1570.00 3461.20
0.27
0.27
0.26
2.5
2.5
2.6
3.7
3.7
3.9
240/950 CAF/W33
950 37.4016 1 360
240/1000 CAF/W33 1 000 39.3701 1 420
240/1060 CAF/W33 1 060 41.7323 1 500
53.5433 412 16.2205 14 800 000 3 327 000 39 000 000 8 770 000
55.9055 412 16.2205 15 400 000 3 462 000 40 500 000 9 100 000
59.0551 438 17.2441 17 300 000 3 889 000 45 500 000 10 230 000
170
160
150
300
280
260
1990.00 4387.20
2140.00 4717.80
2515.00 5544.60
0.27
0.26
0.26
2.5
2.6
2.6
3.7
3.9
3.9
240/1120 CAF/W33 1 120 44.0945 1 580
62.2047 462 18.1890 18 700 000 4 204 000 50 000 000 11 240 000
130
240
2925.00 6448.50
0.26
2.6
3.9
159

Series: 24120 CC/W33 241/630 ECA/W33
Size: 100 mm 630 mm
3.9370 in 24.8031 in
Cylindrical bore
Designation
Bore
Outside diameter
d
D
mm
in
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
ECCJ & CC
design
Tapered bore
lbf
Reference Limiting
speed
speed
r/min r/min
CAC & ECAC

design
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
24120 CC/W33
24122 CC/W33
24124 CC/W33
100
110
120
3.9370
4.3307
4.7244
165
180
200
6.4961
7.0866
7.8740
65
69
80
2.5591
2.7165
3.1496
455 000
520 000
655 000
102 000
117 000
147 000
640 000
750 000
950 000
140 000
170 000
210 000
2 400
2 200
1 900
3 200
3 000
2 600
5.65
7.10
10.30
12.50
15.70
22.70
0.37
0.37
0.37
1.8
1.8
1.8
2.7
2.7
2.7
24126 CC/W33
24128 CC/W33
24130 CC/W33
130
140
150
5.1181
5.5118
5.9055
210
225
250
8.2677 80
8.8583 85
9.8425 100
3.1496
3.3465
3.9370
680 000
765 000
1 020 000
153 000
172 000
229 000
1 000 000
1 160 000
1 530 000
220 000
260 000
340 000
1 800
1 700
1 500
2 400
2 400
2 200
11.00
13.50
20.00
24.30
29.80
44.10
0.35
0.35
0.37
1.9
1.9
1.8
2.9
2.9
2.7
24132 CC/W33
24134 CC/W33
24136 CC/W33
160
170
180
6.2992
6.6929
7.0866
270
280
300
10.6299 109
11.0236 109
11.8110 118
4.2913
4.2913
4.6457
1 180 000
1 220 000
1 400 000
265 000
274 000
315 000
1 760 000
1 860 000
2 160 000
400 000
420 000
490 000
1 400
1 300
1 300
1 900
1 900
1 700
25.00
27.50
34.50
55.10
60.60
76.10
0.40
0.37
0.37
1.7
1.8
1.8
2.5
2.7
2.7
24138 CC/W33
24140 CC/W33
24144 CC/W33
190
200
220
7.4803
7.8740
8.6614
320
340
370
12.5984 128
13.3858 140
14.5669 150
5.0394
5.5118
5.9055
1 600 000
1 800 000
2 120 000
360 000
405 000
477 000
2 500 000
2 800 000
3 350 000
560 000
630 000
750 000
1 200
1 100
1 000
1 600
1 500
1 400
43.00
53.50
67.00
94.80
117.90
147.70
0.40
0.40
0.40
1.7
1.7
1.7
2.5
2.5
2.5
24148 CC/W33
24152 CC/W33
24156 CC/W33
240
260
280
9.4488
10.2362
11.0236
400
440
460
15.7480 160
17.3228 180
18.1102 180
6.2992
7.0866
7.0866
2 400 000
3 000 000
3 100 000
540 000
674 000
697 000
3 900 000
4 800 000
5 100 000
880 000
1 080 000
1 150 000
900
850
800
1 300
1 200
1 100
83.00
110.00
120.00
183.00
242.50
264.60
0.40
0.40
0.40
1.7
1.7
1.7
2.5
2.5
2.5
24160 CC/W33
24164 CC/W33
24168 ECAC/W33
280
320
340
11.0236
12.5984
13.3858
500
540
580
19.6850 200
21.2598 218
22.8346 243
7.8740
8.5827
9.5669
3 750 000
843 000
4 250 000
955 000
4 660 000 1 048 000
6 300 000
7 100 000
8 650 000
1 420 000
1 600 000
1 940 000
700
670
560
1 000
900
850
160.00
210.00
280.00
352.70
463.00
617.30
0.40
0.49
0.40
1.7
1.7
1.7
2.5
2.5
2.5
24172 ECCJ/W33
24176 ECA/W33
24180 ECA/W33
360
380
400
14.1732
14.9606
15.7480
600
620
650
23.6220 243
24.4094 243
25.5906 250
9.5669
9.5669
9.8425
5 600 000 1 259 000 9 300 000

5 700 000 1 281 000 9 800 000
6 200 000 1 394 000 10 600 000
2 090 000
2 200 000
2 380 000
560
480
430
800
850
800
280.00
300.00
340.00
617.30
661.40
749.60
0.37
0.37
0.37
1.7
1.8
1.8
2.5
2.7
2.7
24184 ECA/W33
24188 ECA/W33
24192 ECA/W33
420
440
460
16.5354
17.3228
18.1102
700
720
760
27.5591 280 11.0236

28.3465 280 11.0236
29.9213 300 11.8110
7 350 000 1 652 000 12 600 000

7 500 000 1 686 000 13 200 000
8 300 000 1 866 000 14 600 000
2 830 000
2 970 000
3 280 000
400
400
360
700
700
670
445.00
460.00
560.00
981.00
1014.10
1234.60
0.37
0.37
0.37
1.7
1.8
1.8
2.5
2.7
2.7
24196 ECA/W33
241/500 ECA/W33
241/530 ECA/W33
480
500
530
18.8976
19.6850
20.8661
790
830
870
31.1024 308 12.1260

32.6772 325 12.7953
34.2520 335 13.1890
9 000 000 2 023 000 15 600 000

9 800 000 2 203 000 17 000 000
10 600 000 2 383 000 19 000 000
3 510 000
3 820 000
4 270 000
340
320
300
630
600
560
605.00
700.00
830.00
1333.80
1543.20
1829.80
0.37
0.37
0.37
1.8
1.8
1.8
2.7
2.7
2.7
241/560 ECJ/W33
241/600 ECA/W33
241/630 ECA/W33
560
600
630
22.0472
920
23.6220
980
24.8031 1 030
36.2205 355 13.9764

38.5827 375 14.7638
40.5512 400 15.7480
12 000 000 2 698 000 21 600 000

11 500 000 2 585 000 23 600 000
12 700 000 2 855 000 27 000 000
4 860 000
5 310 000
6 070 000
280
240
220
500 985.00
480 1200.00
450 1400.00
2171.50
2645.50
3086.40
0.35
0.35
0.37
1.9
1.8
1.8
2.9
2.7
2.7
160
Standard
Series: 241/670 ECA/W33 241/1000 ECAF/W33
26.3780 in 39.3701 in
Series: 24892 CAMA/W20 248/1800 CAFA/W20
18.1102 in 70.8661 in
Cylindrical bore
Tapered bore
Designation
CA, ECA, ECAF, CAFA & CAMA

design
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
lbf
Mass
Calculation
factors
kg
lb
e
-
Y1
-
Y2
-
241/670 ECA/W33
241/710 ECA/W33
241/750 ECA/W33
670
710
750
26.3780 1 090
27.9528 1 150
29.5276 1 220
42.9134 412 16.2205 13 800 000 3 102 000

45.2756 438 17.2441 15 200 000 3 417 000
48.0315 475 18.7008 17 300 000 3 889 000
29 000 000
32 500 000
37 500 000
6 520 000
7 310 000
8 430 000
200
190
180
400
380
360
1600.00
1900.00
2100.00
3527.40
4188.70
4629.70
0.37 1.8
0.35 1.8
0.37 1.8
2.7
2.7
2.7
241/800 ECA/W33
241/850 ECA/W33
241/900 ECAF/W33
800
850
900
31.4961 1 280
33.4646 1 360
35.4331 1 420
50.3937 475 18.7008 18 400 000 4 136 000

53.5433 400 15.7480 20 200 000 4 541 000
55.9055 515 20.2756 21 400 000 4 811 000
40 500 000 9 100 000

45 000 000 10 120 000
49 000 000 11 020 000
170
150
140
320
300
280
2300.00
2710.00
3350.00
5070.60
5974.50
7385.40
0.35 1.9
0.35 1.9
0.35 1.9
2.9
2.9
2.9
241/950 ECAF/W33
950
241/1000 ECAF/W33 1 000
37.4016 1 500
39.3701 1 580
59.0551 545 21.4567 23 900 000 5 373 000

62.2047 580 22.8346 26 700 000 6 002 000
55 000 000 12 360 000

62 000 000 13 940 000
130
120
260
240
3535.00
4300.00
7793.30
9479.80
0.35 1.9
0.35 1.9
2.9
2.9
24892 CAMA/W20
248/530 CAMA/W20
248/670 CAMA/W20
18.1102
20.8661
26.3780
580
650
820
22.8346 118
25.5906 118
32.2835 150
4.6457
4.6457
5.9055
1 790 000
1 840 000
3 110 000
402 000
414 000
699 000
4 900 000
5 300 000
9 500 000
1 100 000
1 190 000
2 140 000
560 1 100
480 950
360 700
75.50
86.00
172.00
166.40
189.60
379.20
0.17 4.0
0.15 4.5
0.16 4.2
5.9
6.7
6.3
248/800 CAMA/W20
800
248/900 CAMA/W20
900
248/1060 CAMA/W20 1 060
31.4961
980
35.4331 1 090
41.7323 1 280
38.5827 180
42.9134 190
50.3937 218
7.0866
7.4803
8.5827
4 140 000
931 000
4 660 000 1 048 000
6 100 000 1 371 000
12 900 000
15 300 000
20 000 000
2 900 000
3 440 000
4 500 000
300
240
200
560
480
380
300.00
370.00
570.00
661.40
815.70
1256.60
0.15 4.5
0.14 4.8
0.14 4.8
6.7
7.2
7.2
248/1120 CAFA/W20 1 120

248/1180 CAFA/W20 1 180
248/1320 CAFA/W20 1 320
44.0945 1 360
46.4567 1 420
51.9685 1 600
53.5433 243 9.5669

55.9055 243 9.5669
62.9921 280 11.0236
7 250 000 1 630 000

7 710 000 1 733 000
9 780 000 2 199 000
24 000 000
27 000 000
33 500 000
5 400 000
6 070 000
7 530 000
180
170
140
340
320
260
735.00
770.00
1160.00
1620.40
1697.50
2557.30
0.15 4.5
0.14 4.8
0.15 4.5
6.7
7.2
6.7
248/1500 CAFA/W20 1 500

248/1800 CAFA/W20 1 800
59.0551 1 820
70.8661 2 180
71.6535 315 12.4016 12 700 000 2 855 000

85.8268 375 14.7638 17 600 000 3 956 000
45 000 000 10 120 000

63 000 000 14 160 000
110
75
200
130
1710.00
2900.00
3769.90
6393.30
0.15 4.5
0.15 4.5
6.7
6.7
460
530
670
161

Series: 249/710 CA/W33 249/1500 CAFB/W33
27.9528 in 59.0551 in
Series: ECB 23956 CAC/W33 ECB 23968 CC/W33
Size: 280 mm 340 mm
11.0236 in 13.3858 in
Series: ECB 24036 CC/W33 ECB 24048 CC/W33
Size: 180 mm 240 mm
7.0866 in 9.4488 in
Cylindrical bore
Designation
Bore
Outside diameter
d
D
mm
in
mm
in
249/710 CA/W33
249/750 CA/W33
249/800 CA/W33
Tapered bore
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
CC design
lbf
Reference Limiting
speed
speed
r/min r/min
CA, CAF & CAFB

design
Mass
Calculation
factors
kg
lb
e
-
Y1
-
Y2
-
710 27.9528
950
750 29.5276 1 000
800 31.4961 1 060
37.4016 243 9.5669

39.3701 250 9.8425
41.7323 258 10.1575
6 800 000 1 529 000 15 600 000

7 650 000 1 720 000 18 000 000
8 000 000 1 798 000 19 300 000
3 510 000
4 050 000
4 340 000
300
280
260
500
480
430
495.00
560.00
640.00
1091.30
1234.60
1410.90
0.22
0.22
0.21
3.0
3.0
3.2
4.6
4.6
4.8
850 33.4646 1 120

950 37.4016 1 250
1 000 39.3701 1 320
44.0945 272 10.7087

49.2126 300 11.8110
51.9685 315 12.4016
8 170 000 1 837 000 22 800 000

9 200 000 2 068 000 26 000 000
10 400 000 2 338 000 29 000 000
5 130 000
5 840 000
6 520 000
220
180
170
400 740.00
340 1015.00
320 1200.00
1631.40
2237.70
2645.50
0.22
0.21
0.21
3.0
3.2
3.2
4.6
4.8
4.8
249/1060 CAF/W33 1 060 41.7323 1 400

249/1120 CAF/W33 1 120 44.0945 1 460
249/1180 CAF/W33 1 180 46.4567 1 540
55.1181 335 13.1890

57.4803 335 13.1890
60.6299 355 13.9764
11 500 000 2 585 000 32 500 000

11 700 000 2 630 000 34 500 000
13 600 000 3 057 000 40 500 000
7 310 000
7 760 000
9 100 000
160
140
130
280 1400.00
260 1500.00
240 1800.00
3086.40
3306.90
3968.30
0.21
0.20
0.20
3.2
3.4
3.4
4.8
5.0
5.0
249/1320 CAF/W33 1 320 51.9685 1 720

249/1500 CAFB/W33 1 500 59.0551 1 950
67.7165 400 15.7480

76.7717 450 17.7165
16 100 000 3 619 000 49 000 000 11 020 000

20 700 000 4 653 000 63 000 000 14 160 000
110
85
200 2500.00
150 3550.00
5511.50
7826.30
0.21
0.20
3.2
3.4
4.8
5.0
ECB 23956 CAC/W33

ECB 23960 CC/W33
ECB 23968 CC/W33
280 11.0236
300 11.8110
340 13.3858
380
420
460
14.9606
16.5354
18.1102
75
90
90
2.9528
3.5433
3.5433
845 000
1 200 000
1 460 000
190 000
270 000
328 000
1 760 000
2 500 000
2 800 000
396 000 1 400

562 000 1 300
629 000 1 300
1 700
1 600
1 400
57.00
39.50
45.50
125.70
87.10
100.30
0.16
0.19
0.17
4.2
3.6
4.0
6.3
5.3
5.9
ECB 24036 CC/W33

ECB 24040 CC/W33
ECB 24048 CC/W33
180
200
240
280
310
360
11.0236 100
12.2047 109
14.1732 118
3.9370
4.2913
4.6457
1 080 000
1 290 000
1 600 000
243 000
290 000
360 000
1 730 000
2 120 000
2 700 000
389 000 1 300

477 000 1 300
607 000 1 100
2 200
1 900
1 600
23.00
31.00
43.00
50.70
68.30
94.80
0.33
0.33
0.30
2.0
2.0
2.3
3.0
3.0
3.4
249/850 CA/W33
249/950 CA/W33
249/1000 CA/W33
7.0866
7.8740
9.4488
162
Sealed
SKF Explorer
Series: BS2-2208-2CS BS2-2220-2CS5
Size: 40 mm 100 mm
1.5748 in 3.9370 in
Series: 24020-2CS2 24034-2CS2/VT143
Size: 100 mm 170 mm
3.9370 in 6.6929 in
Cylindrical bore
BS2-xxxx-2CS
design
Tapered bore
Designation
Cylindrical
Tapered
Bore
Outside diameter
Width
d
D
B
mm
in
mm
in
mm
in
Basic load ratings

Dynamic
C
N
lbf
Speed
rating
Static
C0
N
Mass
lbf
Limiting
speed
r/min
kg
lb
Calculation
factors
e
-
Y1
-
Y2
-
BS2-2208-2CS
BS2-2209-2CS
BS2-2210-2CS
BS2-2208-2CSK
BS2-2209-2CSK
BS2-2210-2CSK
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1496
3.3465
3.5433
28.0 1.1024
28.0 1.1024
28.0 1.1024
96 500
102 000
104 000
21 700
23 000
23 400
90 000
98 000
108 000
20 300
22 100
24 300
2 200
2 000
1 900
0.57
0.66
0.70
1.30
1.50
1.50
0.28 2.4 3.6

0.26 2.6 3.9
0.24 2.8 4.2
BS2-2211-2CS
BS2-2212-2CS
24013-2CS5
BS2-2211-2CSK
BS2-2212-2CSK
-
55
60
65
2.1654
2.3622
2.5591
100
110
100
3.9370
4.3307
3.9370
31.0 1.2205
34.0 1.3386
35.0 1.3780
125 000
156 000
132 000
28 100
35 100
29 700
127 000
166 000
173 000
28 600
37 400
38 900
1 700
1 600
130
1.00
1.30
0.95
2.20
2.90
2.10
0.24 2.8 4.2

0.24 2.8 4.2
0.27 2.5 3.7
BS2-2213-2CS
BS2-2214-2CS
24015-2CS2
BS2-2213-2CSK
BS2-2214-2CSK
-
65
70
75
2.5591
2.7559
2.9528
120
125
115
4.7244
4.9213
4.5276
38.0 1.4961
38.0 1.4961
40.0 1.5748
193 000
208 000
173 000
43 400
46 800
38 900
216 000
228 000
232 000
48 600
51 300
52 200
1 500
1 400
130
1.60
1.80
1.55
3.50
4.00
3.40
0.24 2.8 4.2

0.23 2.9 4.4
0.28 2.4 3.6
BS2-2215-2CS
BS2-2216-2CS
BS2-2217-2CS
BS2-2215-2CSK
BS2-2216-2CSK
BS2-2217-2CSK
75
80
85
2.9528
3.1496
3.3465
130
140
150
5.1181
5.5118
5.9055
38.0 1.4961
40.0 1.5748
44.0 1.7323
212 000
236 000
285 000
47 700
53 100
64 100
240 000
270 000
325 000
54 000
60 700
73 100
1 300
1 200
1 100
2.10
2.40
3.00
4.60
5.30
6.60
0.22 3.0 4.6

0.22 3.0 4.6
0.22 3.0 4.6
BS2-2218-2CS
BS2-2220-2CS5
BS2-2218-2CSK
-
90
100
3.5433
3.9370
160
180
6.2992
7.0866
48.0 1.8898
55.0 2.1654
325 000
425 000
73 100
95 600
375 000 84 300

490 000 110 200
1 000
110
3.70
5.50
8.20
12.10
0.24 2.8 4.2

0.24 2.8 4.2
24020-2CS2
23120-2CS2
23220-2CS
100
100
100
3.9370
3.9370
3.9370
150
165
180
5.9055
6.4961
7.0866
50.0 1.9685
52.0 2.0472
60.3 2.3740
285 000 64 100

365 000 82 100
475 000 106 800
415 000 93 300

490 000 110 200
600 000 135 000
95
100
700
3.20
4.40
6.70
7.10
9.70
14.80
0.28 2.4 3.6

0.27 2.5 3.7
0.30 2.3 3.4
23024-2CS2
24024-2CS2
23026-2CS2
120
120
130
4.7244
4.7244
5.1181
180
180
200
7.0866
7.0866
7.8740
46.0 1.8110
60.0 2.3622
52.0 2.0472
355 000
430 000
430 000
510 000 115 000

670 000 151 000
610 000 137 000
100
80
95
4.20
5.45
6.00
9.30
12.00
13.20
0.20 3.4 5.0

0.28 2.4 3.6
0.21 3.2 4.8
24126-2CS2
24028-2CS2
24128-2CS2
130
140
140
5.1181
5.5118
5.5118
210
210
225
8.2677
8.2677
8.8583
80.0 3.1496
69.0 2.7165
85.0 3.3465
680 000 152 900 1 000 000 225 000

570 000 128 200 900 000 202 000
765 000 172 000 1 160 000 261 000
67
55
55
11.00
8.55
13.50
24.30
18.80
29.80
0.33 2.0 3.0

0.28 2.4 3.6
0.35 1.9 2.9
24030-2CS2
24032-2CS2/VT143
24034-2CS2/VT143
150
160
170
5.9055
6.2992
6.6929
225 8.8583
240 9.4488
260 10.2362
75.0 2.9528
80.0 3.1496
90.0 3.5433
655 000 147 300 1 040 000 234 000

750 000 168 600 1 200 000 270 000
930 000 209 100 1 460 000 328 000
67
450
400
10.50
13.00
17.50
23.10
28.70
38.60
0.28 2.4 3.6

0.28 2.4 3.6
0.33 2.0 3.0
79 900
96 700
96 700
163

Shaker screen
SKF Explorer
Series: 22308 E/VA405 22340 CCJA/VA405
Size: 40 mm 200 mm
1.5748 in 7.8740 in
Cylindrical bore
Designation
Bore
d
mm
Outside diameter
D
in
mm
in
E/VA405
Tapered bore*
Basic load ratings
Width
B
mm
in
Dynamic
C
lbf
CCJA/VA405
Speed rating
Static
C0
lbf
Mass
Calculation
factors
Reference Limiting
speed
speed
r/min r/min
kg
lb
e
-
Y1
-
Y2
-
22308 E/VA405
22309 E/VA405
22310 E/VA405
40
45
50
1.5748 90
1.7717 100
1.9685 110
3.5433
3.9370
4.3307
33
36
40
1.2992
1.4173
1.5748
150 000
183 000
220 000
33 700
41 100
49 500
140 000
183 000
224 000
31 500
41 100
50 400
6 000
5 300
4 800
8 000
7 000
6 300
1.05
1.40
1.90
2.30 0.37 1.80 2.70

3.10 0.37 1.80 2.70
4.20 0.37 1.80 2.70
22311 E/VA405
22312 E/VA405
22313 E/VA405
55
60
65
2.1654 120
2.3622 130
2.5591 140
4.7244
5.1181
5.5118
43
46
48
1.6929
1.8110
1.8898
270 000
310 000
340 000
60 700
69 700
76 400
280 000
335 000
360 000
62 900
75 300
80 900
4 300
4 000
3 800
5 600
5 300
5 000
2.45
3.10
3.75
5.40 0.35 1.90 2.90

6.80 0.35 1.90 2.90
8.30 0.35 1.90 2.90
22314 E/VA405
22315 EJA/VA405
22316 EJA/VA405
70
75
80
2.7559 150
2.9528 160
3.1496 170
5.9055
6.2992
6.6929
51
55
58
2.0079
2.1654
2.2835
400 000
440 000
490 000
89 900
98 900
110 200
430 000
475 000
540 000
96 700
106 800
121 400
3 400
3 200
3 000
4 500
4 300
4 000
4.55
5.55
6.60
10.00 0.33 2.00 3.00

12.20 0.35 1.90 2.90
14.60 0.35 1.90 2.90
22317 EJA/VA405
22318 EJA/VA405
22319 EJA/VA405
85
90
95
3.3465 180
3.5433 190
3.7402 200
7.0866
7.4803
7.8740
60
64
67
2.3622
2.5197
2.6378
550 000
610 000
670 000
123 600
137 100
150 600
620 000
695 000
765 000
139 400
156 200
172 000
2 800
2 600
2 600
3 800
3 600
3 400
7.65
9.05
10.50
16.90 0.33 2.00 3.00

20.00 0.33 2.00 3.00
23.10 0.33 2.00 3.00
22320 EJA/VA405
22322 EJA/VA405
22324 CCJA/VA405
100
110
120
3.9370 215 8.4646

4.3307 240 9.4488
4.7244 260 10.2362
73
80
86
2.8740
3.1496
3.3858
815 000
950 000
965 000
183 200
213 600
216 900
950 000
1 120 000
1 120 000
213 600
251 800
251 800
2 400
2 000
2 000
3 000
2 800
2 600
13.50
18.40
23.00
29.80 0.33 2.00 3.00

40.60 0.33 2.00 3.00
50.70 0.35 1.90 2.90
22326 CCJA/VA405
22328 CCJA/VA405
22330 CCJA/VA405
130
140
150
5.1181 280 11.0236 93

5.5118 300 11.8110 102
5.9055 320 12.5984 108
3.6614 1 120 000

4.0157 1 290 000
4.2520 1 460 000
251 800
290 000
328 200
1 320 000
1 560 000
1 760 000
296 700
350 700
395 600
1 800
1 700
1 600
2 400
2 200
2 000
29.00
36.50
43.50
63.90 0.35 1.90 2.90

80.50 0.35 1.90 2.90
95.90 0.35 1.90 2.90
22332 CCJA/VA405
22334 CCJA/VA405
22336 CCJA/VA405
160
170
180
6.2292 340 13.3858 114

6.6929 360 14.1732 120
7.0866 380 14.9606 126
4.4882 1 600 000

4.7244 1 760 000
4.9606 2 000 000
359 700
395 600
449 600
1 960 000
2 160 000
2 450 000
440 600
485 600
550 800
1 500
1 400
1 300
1 900
1 800
1 700
52.00
61.00
71.50
114.60 0.35 1.90 2.90

134.50 0.33 2.00 3.00
157.60 0.35 1.90 2.90
22338 CCJA/VA405
22340 CCJA/VA405
190
200
7.4803 400 15.7480 132

7.8740 420 16.5354 138
5.1968 2 120 000

5.4331 2 320 000
476 600
521 500
2 650 000
2 900 000
595 700
651 900
1 200
1 200
1 600
1 500
82.50
95.00
181.90 0.35 1.90 2.90

209.40 0.33 2.00 3.00
* Tapered (K) bore available on limited sizes.
164
Shaker screen
Series: 452308 M2/W502 452340 M2/W502
Size: 40 mm 200 mm
1.5748 in 7.8740 in
Series: 453322 M2/W502 453332 M2/W502
Size: 110 mm 160 mm
4.3307 in 6.2992 in
Series: 453322 EJA/VA405 453332 CCJA/VA405
Size: 110 mm 160 mm
4.3307 in 6.2992 in
Cylindrical bore
M2/W502
Tapered bore*
Designation
Bore
d
mm
Outside diameter
D
in
mm
in
Basic load ratings
Width
B
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed
speed
r/min r/min
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
452308 M2/W502
452309 M2/W502
452310 M2/W502
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
33
36
40
1.2992
1.4173
1.5748
107 000
133 000
168 000
24 100
29 900
37 800
112 000
150 000
186 000
25 200
33 700
41 800
5 600
4 800
4 300
8 000
7 000
6 300
1.00
1.35
1.85
2.20
3.00
4.10
0.37 1.80 2.70

0.37 1.80 2.70
0.37 1.80 2.70
452311 M2/W502
452312 M2/W502
452313 M2/W502
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
43
46
48
1.6929
1.8110
1.8898
199 000
235 000
258 000
44 700
52 800
58 000
232 000
280 000
305 000
52 200
62 900
68 600
4 000
3 800
3 400
6 000
5 300
5 000
2.35
2.95
3.55
5.20
6.50
7.80
0.35 1.90 2.90

0.35 1.90 2.90
0.35 1.90 2.90
452314 M2/W502
452316 M2/W502
452317 M2/W502
70
80
85
2.7559
3.1496
3.3465
150
170
180
5.9055
6.6929
7.0866
51
58
60
2.0079
2.2835
2.3622
299 000
374 000
408 000
67 200
84 100
91 700
360 000
465 000
490 000
80 900
104 500
110 200
3 200
2 800
2 600
4 500
4 000
3 800
4.30
6.10
7.25
9.50
13.40
16.00
0.35 1.90 2.90

0.35 1.90 2.90
0.33 2.00 3.00
452318 M2/W502
452319 M2/W502
452320 M2/W502
90
95
100
3.5433
3.7402
3.9370
190
200
215
7.4803
7.8740
8.4646
64
67
73
2.5197
2.6378
2.8740
460 000
518 000
610 000
103 400
116 400
137 100
570 000
670 000
800 000
128 100
150 600
179 800
2 400
2 400
2 200
3 600
3 400
3 200
8.60
10.00
13.00
19.00
22.00
28.70
0.35 1.90 2.90

0.35 1.90 2.90
0.35 1.90 2.90
452322 M2/W502
452324 M2/W502
452326 M2/W502
110
120
130
4.3307
4.7244
5.1181
240
260
280
9.4488
10.2362
11.0236
80
86
93
3.1496
3.3858
3.6614
725 000
845 000
978 000
163 000
190 000
219 900
965 000
1 140 000
1 320 000
216 900
256 300
296 700
2 000
1 800
1 700
2 800
2 600
2 400
18.00
22.00
28.50
39.70
48.50
62.80
0.35 1.90 2.90

0.35 1.90 2.90
0.35 1.90 2.90
452328 M2/W502
452330 M2/W502
452332 M2/W502
140
150
160
5.5118
5.9055
6.2992
300
320
340
11.8110 102
12.5984 108
13.3858 114
4.0157
4.2520
4.4882
1 130 000
1 290 000
1 400 000
254 000
290 000
314 700
1 560 000
1 800 000
1 960 000
350 700
404 600
440 600
1 500
1 400
1 300
2 200
2 000
1 900
34.50
41.50
50.00
76.10
91.50
110.20
0.35 1.90 2.90

0.35 1.90 2.90
0.35 1.90 2.90
452340 M2/W502
200
7.8740
420
16.5354 138
5.4331
1 020 000
229 300
2 900 000
651 900
1 100
1 500
93.00
205.00
0.33 2.00 3.00
453322 M2/W502
453324 M2/W502
453328 M2/W502
110
120
140
4.3307
4.7244
5.5118
240
260
300
9.4488 92.1
10.2362 106
11.8110 118
3.6260
4.1732
4.6457
817 000
978 000
1 240 000
183 700
219 900
278 800
1 100 000
1 340 000
1 730 000
247 300
301 200
388 900
1 900
1 700
1 500
2 800
2 600
2 200
20.50
27.00
40.90
45.20
59.50
90.20
0.40 1.70 2.50

0.43 1.60 2.30
0.40 1.70 2.50
453332 M2/W502
160
6.2992
340
13.3858 136
5.3543
1 640 000
368 700
2 400 000
539 500
1 300
1 900
60.20
132.70
0.40 1.70 2.50
453322 EJA/VA405 110

453324 CCJA/VA405 120
453326 CCJA/VA405 130
4.3307
4.7244
5.1181
240
260
280
9.4488 92.1
10.2362 106
11.0236 112
3.6260
4.1732
4.4094
950 000
965 000
1 120 000
213 600
216 900
251 800
1 120 000
1 120 000
1 320 000
251 800
251 800
296 700
2 000
2 000
1 800
2 800
2 600
2 400
20.50
27.00
35.50
45.20
59.50
78.30
0.33 2.00 3.00

0.35 1.90 2.90
0.35 1.90 2.90
453328 CCJA/VA405 140

453330 CCJA/VA405 150
453332 CCJA/VA405 160
5.5118
5.9055
6.2992
300
320
340
11.8110 118
12.5984 128
13.3858 136
4.6457
5.0394
5.3543
1 290 000
1 460 000
1 600 000
290 000
328 200
359 700
1 560 000
1 760 000
1 960 000
350 700
395 600
440 600
1 700
1 600
1 500
2 200
2 000
1 900
40.90
47.50
60.20
90.20
104.70
132.70
0.35 1.90 2.90

0.35 1.90 2.90
0.35 1.90 2.90
* Tapered (K) bore available on limited sizes.
165

Printing press
Series: 22209 CCK/VA759 23226 VAD
Size: 45.000 mm 130.000 mm
1.7717 in 5.1181 in
EK/VA7xx
CCK/Vxx
4xxxxx
Please contact SKF Applications Engineering for tapered journal (X drawings) details.
Designation
Current
Bore
d
Basic load ratings
Basic/
replaced
design
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
mm
in
22209 CCK/VA759
22211 EK/VA751
22212 EK/VA751
22209 CCK/W33
22211 VAE
22212 VAD
45.000
55.000
60.000
1.7717
2.1654
2.3622
85
100
110
3.3465
3.9370
4.3307
23.0
25.0
28.0
0.9055
0.9843
1.1024
138 000
99 500
122 000
22212 EK/VA7582
22220 VAE
22220 EK/VA751
22212 EK/VA751
22220 CCK/W33
22220 EK/VA751
60.000
100.000
100.000
2.3622
3.9370
3.9370
110
180
180
4.3307
7.0866
7.0866
28.0
46.0
46.0
1.1024
1.8110
1.8110
122 000
311 000
425 000
22230 VAB
22309 EK/VA751
22310 EK/VA751
22230 CCK/W33
450918
467964
150.000
45.000
50.000
5.9055
1.7717
1.9685
270 10.6299
100 3.9370
110 4.3307
73.0
36.0
40.0
2.8740
1.4173
1.5748
736 000
138 000
176 000
22311 EK/VA751
22312 EK/VA751
22312 EK/VA7582
22311 VAE
467000
22312 EK/VA7583
55.000
60.000
60.000
2.1654
2.3622
2.3622
120
130
130
4.7244
5.1181
5.1181
43.0
46.0
46.0
1.6929
1.8110
1.8110
199 000
235 000
235 000
44 800
52 900
52 900
232 000
280 000
280 000
22312 EK/VA7583
22315 CCK/VA755
22315 VAE
22312 EK/VA751
22315 CCK/W33
466915
60.000
75.000
75.000
2.3622
2.9528
2.9528
130
160
160
5.1181
6.2992
6.2992
46.0
55.0
55.0
1.8110
2.1654
2.1654
235 000
345 000
345 000
52 900
77 600
77 600
280 000
430 000
430 000
22315 VAH
22319 VAC
23122 VAF
22315 VAE
22319 CCK/W33
23122 CCK/W33
75.000
95.000
110.000
2.9528
3.7402
4.3307
160
200
180
6.2992
7.8740
7.0866
55.0
67.0
56.0
2.1654
2.6378
2.2047
345 000
518 000
374 000
77 600
117 000
84 000
23124 VAA
23130 VAA**
23220 VAA
23124 CCK/W33
23130 CCK/W33
23220 CCK/W33
120.000
151.333
100.000
4.7244
5.9579
3.9370
200
250
180
7.7840
9.8425
7.0866
62.0
80.0
60.3
2.4409
3.1496
2.3470
ECB 23220 VAA

23222 CCK/VA756
23226 VAD
EVB 23220 VAA

23222 CCK/W33
23226 CCK/W33
100.000
110.000
130.000
3.9370
4.3307
5.1181
180
200
230
7.0866
7.8740
9.0551
60.3
69.8
80.0
2.3470
2.7480
3.1496
Mass
Calculation
factors
Static
C0
lb
e
-
1.35
0.82
1.10
3.00
1.80
2.45
0.26
0.24
0.24
2.6 3.9
2.8 4.2
2.8 4.2
146 000 32 800

415 000 93 300
490 000 110 200
1.10
4.85
4.80
2.45
10.50
10.60
0.24
0.24
0.24
2.8 4.2
2.8 4.2
2.8 4.2
166 000 1 080 000 243 000

31 000
160 000 31 100
39 600
200 000 45 000
18.00
1.35
1.85
39.50
3.00
4.10
0.26
0.37
0.37
2.6 3.9
1.8 2.7
1.8 2.7
52 200
63 000
63 000
2.35
2.95
2.95
5.20
6.50
6.50
0.35
0.35
0.35
1.9 2.9
1.9 2.9
1.9 2.9
63 000
96 700
96 700
2.95
5.25
5.25
6.50
11.50
11.50
0.35
0.35
0.35
1.9 2.9
1.9 2.9
1.9 2.9
430 000 96 700

670 000 151 000
585 000 132 000
5.25
10.00
5.45
11.50
22.00
12.00
0.35
0.35
0.30
1.9 2.9
1.9 2.9
2.3 3.4
437 000
725 000
414 000
98 300
695 000 156 000
163 000 1 200 000 270 000
93 200
600 000 135 000
7.80
16.00
6.70
17.00
35.50
15.00
0.28
0.30
0.33
2.4 3.6
2.3 3.4
2.0 3.0
414 000
518 000
690 000
93 200
600 000 135 000
117 000
765 000 172 000
155 000 1 060 000 238 000
6.70
9.70
14.00
15.00
21.50
31.00
0.33
0.33
0.33
2.0 3.0
2.0 3.0
2.0 3.0
lbf
31 000
22 400
27 000
160 000
118 000
146 000
31 100
26 500
32 800
27 000
70 000
95 500
kg
* Special bore size

** Controlled inner ring width
Coater roll bearing w/ .000050 runout max
Coater roll bearing w/ .000075 runout max.
166
Y1
-
Y2
-
Printing press
Series: 453538 468603
Size: 50.000 mm 110.000 mm
1.9685 in 4.3307 in
45xxxx & 46xxxx
Please contact SKF Applications Engineering for tapered journal (X drawings) details.
Designation
Current
Basic/
replaced
design
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Mass
Calculation
factors
Static
C0
N
lbf
kg
lb
e
-
Y1
-
Y2
-
453538
454548
458681
22210 CCK/W33
23126 CCK/W33
22217 CCK/W33
50.000
130.000
85.000
1.9685
5.1181
3.3465
90
210
150
3.5433
8.2677
5.9055
23.0
64.0
36.0
.9055
2.5197
1.4173
84 500 19 000
489 000 110 000
210 000 47 200
100 000 22 500

780 000 175 000
270 000 60 700
0.60
8.55
2.55
1.30 0.24 2.8 4.2

19.00 0.28 2.4 3.6
5.60 0.22 3.0 4.6
465123
466144
466144 A**
22216 CCK/W33
23122 CCK/W33
23122 CCK/W33
80.000
110.000
110.000
3.1496
4.3307
4.3307
140
180
180
5.5118
7.0866
7.0866
33.0
56.0
56.0
1.2992
2.2047
2.2047
176 000
374 000
374 000
228 000 51 300

585 000 132 000
585 000 132 000
2.05
5.45
5.45
4.50 0.22 3.0 4.6

12.00 0.30 2.3 3.4
12.00 0.30 2.3 3.4
466713
466816
466817
23230 CCK/W33
23226 CCK/W33
23228 CCK/W33
150.000
130.000
140.000
5.9055
5.1181
5.5118
270 10.6299
230 9.0551
250 9.8425
96.0
80.0
88.0
3.7795
3.1496
3.4646
937 000 211 000 1 460 000 328 000

690 000 155 000 1 060 000 238 000
799 000 180 000 1 250 000 281 000
24.00
14.00
18.50
53.00 0.35 1.9 2.9

31.00 0.33 2.0 3.0
41.00 0.33 2.0 3.0
466915
467304
467311
22315 CCK/W33
22314 CCK/W33
22316 CCK/W33
75.000
70.000
80.000
2.9528
2.7559
3.1496
160
150
170
6.2992
5.9055
6.6929
55.0
51.0
58.0
2.1654
2.0079
2.2835
345 000
311 000
374 000
77 600
70 000
84 200
430 000 96 700

380 000 85 400
455 000 102 000
5.25
4.30
6.20
11.50 0.35 1.9 2.9

9.50 0.35 1.9 2.9
13.50 0.35 1.9 2.9
467315
467418
468043
22317 CCK/W33
22218 CCK/W33
23222 CCK/W33
85.000
90.000
110.000
3.3465
3.5433
4.3307
180
160
200
7.0866
6.2992
7.8740
60.0
40.0
69.8
2.3622
1.5748
2.7480
420 000 94 500

253 000 56 900
518 000 117 000
520 000 117 000

340 000 76 400
765 000 172 000
7.25
3.25
9.70
16.00 0.33 2.0 3.0

7.15 0.23 2.9 4.4
21.50 0.33 2.0 3.0
468603
22222 CCK/W33
110.000
4.3307
200
7.8740
53.0
2.0866
408 000
560 000 126 000
7.00
15.50 0.25 2.7 4.0
39 600
84 000
84 000
91 800
* Special bore size

** Controlled inner ring width
167

Special bearings
Series: I-26310 CAM2/W33 ECBI-112630 CAC/W33
Size: 200 mm 350 mm
7.8740 in 13.7795 in
Cylindrical bore
Designation
Bore
d
mm
in
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
CA design
Speed rating
Static
C0
lbf
Tapered bore
Reference Limiting
speed
speed
lbf
r/min
r/min
Mass
kg
Calculation
factors
lb
e
-
Y1
-
Y2
-
I-26310 CAM2/W33*
I-26311 CAM2/W33*
I-28809 CAM2/W33*
200
220
190
7.8740 380
8.6614 420
7.4803 280
14.9606 126
16.5354 138
11.0236
67
4.9606 1 730 000

5.4331 2 070 000
2.6378
644 000
390 000 2 700 000

465 000 3 200 000
145 000 1 140 000
610 000
720 000
256 000
750
670
1 700
950
850
2 200
68.00
90.50
15.00
150.00 0.33 2.0

200.00 0.33 2.0
33.00 0.21 3.2
3.0
3.0
4.8
I-28814 CAM2/W33*
I-28821 CACM2/W33*
I-37611 CAM2/W33**
240
310
220
9.4488 350
12.2047 455
8.6614 420
13.7795
83
17.9134 109
16.5354 138
3.2677
978 000
4.2913 1 680 000
5.4331 2 070 000
220 000 1 830 000

378 000 3 250 000
465 000 3 200 000
411 000
730 000
720 000
850
630
670
1 100
800
850
27.50
66.00
90.50
60.50 0.21 3.2

145.00 0.21 3.2
200.00 0.33 2.0
4.8
4.8
3.0
I-37617 CA/W33**
340
I-112618 CA/W33**
250
ECBI-112630 CAC/W33** 350
13.3858 640
9.8425 410
13.7795 590
25.1969 190
16.1417 128
23.2283 192
7.4803 4 080 000

5.0394 1 760 000
7.5591 3 740 000
920 000 6 550 000 1 500 000

400 000 3 100 000 700 000
840 500 6 800 000 1 530 000
480
630
430
600 150.00
800
68.00
530 220.00
640.00 0.30 2.3

150.00 0.30 2.3
485.00 0.30 2.3
3.4
3.4
3.4
* Cylindrical bore
** Tapered bore
168
CARB
Toroidal roller bearings

Nomenclature
C2222 KV TN9 / C3
4
2
1
1. Variations:
4. Clearance & features:
Bearing with 1 to 12 tapered

bore
C2

< Normal
K30
Bearing with 1 to 30 tapered

bore
(C0)*

clearance
C3

> Normal
2. Internal design:
C4

> C3
C08
RBEC class 5 (ISO class P5)

running accuracy
HA3
Case hardened inner ring
HA4
Case hardened inner and

outer rings and rollers

(without cage)
3. Cage designs:
TN9
Nylon cage, rolling element

guided
VE240
Bearing modified for greater

axial displacement
Machined brass cage

(large bore > 500 mm only)
2CS5
Two synthetic rubber seals

with Kluber grease
No cage suffix indicates

window-type sheet steel cage
169
CARB
Product
Details
Technical
features
Boundary dimensions
Tolerances

SKF CARB bearings up to 315 mm bore
diameter are produced to higher precision
than ISO Normal tolerances; the width
tolerance is considerably less than the
ISO Normal tolerance. The running accuracy
is to tolerance class P5 as standard.
For larger bearings, P5 tolerances are
also available with the suffix C08 or closer
tolerances are available with the suffix VQ 424.
Heat stabilization
392 F (200 C)
Misalignment
0.5 degrees between the inner and

outer rings
Cage material
Standard
Steel
Optional
Nylon (TN9)
Brass (M)
Axial load max
None
Seals
2CS5 - 2 synthetic rubber (NRB) seals with

high temperature (70 - 100%) fill grease
CARB bearing
170
Introduction
Introduction
The CARB toroidal roller bearing can support
very heavy radial loads. It is intended exclusively as a non-locating or floating bearing
and as such is ideal with its combination of
self-aligning and axial alignment properties,
opening up completely new opportunities to
save space, weight and arrangement costs.
By deliberately displacing the rings axially
with respect to each other, it is possible to
accurately set the internal radial clearance in
the bearing.
These bearings permit smaller and lighter
bearing arrangement designs offering the
same or heightened performance in a
particularly impressive manner; for example,
in planetary gearboxes. They also simplify the
bearing arrangement design for long shafts,
which are subjected to temperature variations
and also reduce vibrations; for example, in
papermaking machines or ship propulsion
arrangements. CARB does not pass axial
vibrations in the shaft to the housing. The list
of applications where CARB is appropriate is
long. SKF Applications Engineering can supply
additional information and special publications
on request.
The rollers of the CARB are self-guiding, i.e.

they will always adopt the position where the
load is evenly distributed over the roller
lengthirrespective of whether the inner ring
is axially displaced and/or misaligned with
respect to the outer ring.
The load carrying capacity of the CARB is
very high even when it has to compensate for
angular misalignments or axial displacements.
This results in operationally reliable bearing
arrangements with long service life. The load
carrying capacity of the full complement
CARB is appreciably higher than that of the
caged bearing.
The CARB is produced in a caged design
(Figure 1) as well as a full complement
version (Figure 2) and is available with a cylindrical or with a tapered bore. Depending on
bearing width, the tapered bore has a taper of
either 1:12 (designation suffix K) which is the
most popular or 1:30 (suffix K30) which is
limited to only a few sizes.
A breakthrough in bearing
technology
The CARB (Compact Aligning Roller
Bearing) toroidal roller bearing is a
major breakthrough in bearing technology. This is the first new bearing type
in over 50 years.
Three-in-one bearing
The CARB toroidal roller bearing is
space-saving like a needle roller bearing, self-aligning like a spherical roller
bearing, and axially free like a cylindrical bearingcombining the application
and performance advantages of all
three bearings.
Longer service life, increased

uptime, reduced costs
SKF Explorer class

bearings
All CARB bearings are manufactured to the
SKF Explorer performance class. In the product
tables, the SKF Explorer bearing designations
are printed in blue.
Basic design
Product highlights
The CARB toroidal roller bearing is a single

row bearing with long, slightly crowned rollers.
The raceways of both inner and outer rings
are concave and symmetrical about a line
through the bearing center. The optimum
combination of raceway profiles guarantees a
favorable load distribution in the bearings as
well as low friction.
A toroidal roller bearing adapts to

both angular misalignment and axial
displacement simultaneously. Because
the CARB tolerates more than any
other bearing, it can help extend
service life, increase machine uptime,
and reduce maintenance costs where
conventional bearings now experience
premature failure.

CARB is available with a cage or in a
full complement design without a
cage, with a choice of cylindrical or
tapered bore.
Figure 1
Figure 2
The low minimum load requirement

makes the CARB a good candidate
for fans while the higher running
accuracy makes it suitable for precision
equipment.
171
CARB
Introduction
Variations
Bearings on adapter or withdrawal
sleeve
A CARB with tapered bore can be mounted on
an adapter sleeve with a low profile locknut
(KML) (Figure 3) or a withdrawal sleeve
(Figure 4) in the same way as a self-aligning
ball bearing or a spherical roller bearing on
smooth or stepped shafts in an easy and rapid
manner. If large axial displacements are
expected, care should be taken to see that
they take place towards the same side of the
arrangement as the sleeve locknut (Figure 5).
Figure 3
Figure 4
172
Bearings on adapter sleeve
Appropriate housings
The use of an adapter sleeve is the most

popular means of securing a bearing with a
tapered bore on a cylindrical seating. Adapter
sleeves can be used both with smooth and
stepped shafts. They are simple to mount and
require no additional fixation on the shaft.
On smooth shafts CARB can be mounted at
any position. Where stepped shafts are used
together with a support ring, the bearing
position can be accurately defined and dismounting of the bearing is also simplified.
Where appropriate, adapter sleeves of the
E and L variants are available, e.g. H 310 E.
Adapter sleeves of the E type are supplied
with a spacer ring which should be arranged
between the bearing and the locking washer
to prevent the washer from contacting the
cage when axial displacement occurs. Where
adapter sleeves of the L type are concerned,
the standard locking arrangement (KM + MB)
has been replaced by the lower section nut
KML with MBL locking washer. Any contacting
of the cage by the sleeve locking device is
thus prevented.
Mounting and dismounting of bearings on
adapter sleeves can be greatly facilitated by
the use of an hydraulic nut (Figure 6) or
adapter sleeves for oil injection mounting.
For details, please reference the SKF Bearing
Installation and Maintenance Guide (140-710).
Any CARB toroidal roller bearing belonging to

C22xx, C23xx can be mounted in almost any
SKF standard bearing housing, irrespective of
whether the bearing is mounted on a cylindrical stepped shaft or on an adapter sleeve on a
smooth shaft. Figure 7 shows a CARB C 2220
in a SNL plummer block housing.
The extensive range of SKF housings can be
found in other SKF publications that can be
supplied on request.
Figure 5
Figure 7
Figure 6
Introduction
Internal clearance
The CARB is produced as standard with Normal
radial internal clearance. Many of the bearings
are also available with C3 clearance and some
with the smaller C2 or the much larger C4 clearance. The availability of bearings with clearance
other than Normal should be checked prior to
design change or order placement.
The radial internal clearance limits for bearings
with cylindrical bore are given in Table 1 and for
bearings with tapered bore in Table 2. They are
valid for bearings before mounting and under
zero measuring load.
Axial displacement of the one ring in relation to

the other will reduce the clearance in a CARB.
This is also the reason why the clearance is
larger than a comparable size of spherical roller
bearing having the same clearance class.
Axial displacement
The permissible axial displacement of the
inner ring of a CARB with respect to the outer
ring depends on the radial internal clearance.
The relationship between the radial internal
clearance and the permissible axial displacement from the central position is shown in
Diagram 1, page 175. In fact, the bearing rings
can be further displaced with respect to each
other, even into the grey region, without any
effect on bearing life. Bearing friction, however,
will be increased by up to 50% as a result.
The guideline values given for s in the product

tables represent the theoretically possible axial
displacement of one ring in relation to the
other from the central position under zero
misalignment where the rollers
of bearings with a cage will not protrude
from the bearing rings, and
of full complement bearings will not contact
the retaining ring in the outer ring raceway.
A rough estimate of the permissible axial
displacement for bearings having Normal radial
internal clearance, one ring mounted with an
interference fit, and an operating temperature
of approximately 158 F (70 C), is 0.5 s. If the
bearing has C3 radial internal clearance, the
corresponding estimate is 0.65 s.
Table 1
Radial internal clearance of CARB bearings with cylindrical bore
Bore
diameter
d
over
mm

incl.
C2
min
m
max
Normal
max
m
min
C3
max
m
min
C4
max
m
min
C5
max
m
min
18
24
30
24
30
40
15
18
21
27
32
39
27
32
39
39
46
55
39
46
55
51
60
73
51
60
73
65
76
93
65
76
93
81
94
117
40
50
65
50
65
80
25
33
40
45
54
66
45
54
66
65
79
96
65
79
96
85
104
124
85
104
124
109
139
164
109
139
164
137
174
208
80
100
120
100
120
140
52
64
76
82
100
119
82
100
119
120
144
166
120
144
166
158
186
215
158
186
215
206
244
280
206
244
280
258
306
349
140
160
180
160
180
200
87
97
108
138
152
171
38
52
171
195
217
238
195
217
238
252
280
307
252
280
307
321
361
394
321
361
394
398
448
495
200
225
250
225
250
280
118
128
137
187
202
221
187
202
221
262
282
307
262
282
307
337
368
407
337
368
407
434
478
519
434
478
519
545
602
655
280
315
355
315
355
400
152
164
175
236
259
280
236
259
280
330
360
395
330
360
395
434
483
528
434
483
528
570
620
675
570
620
675
714
789
850
400
450
500
450
500
560
191
205
220
307
335
360
307
335
360
435
475
518
435
475
518
577
633
688
577
633
688
745
811
890
745
811
890
929
1015
1110
560
630
710
630
710
800
245
267
300
395
435
494
395
435
494
567
617
680
567
617
680
751
831
920
751
831
920
975
1075
1200
975
1075
1200
1215
1335
1480
800
900
1000
900
1000
1120
329
370
410
535
594
660
535
594
660
755
830
930
755
830
930
1015
1120
1260
1015
1120
1260
1325
1460
1640
1325
1460
1640
1655
1830
2040
1120
1250
450
720
720
1020
1020
1380
1380
1800
1800
2240
173
CARB
The permissible axial displacement is limited in

operation by the operating clearance in the
bearing and the actual angular misalignment.
The influence of the operating clearance is
shown in Diagram 1, page 175.
If the axial movement exceeds 50% of the
permissible axial displaceability s, it should be
checked, whether the residual radial internal
clearance is sufficiently large.
If the axial movement exceeds 50%

of the axial displaceability s, and the
misalignment attains approximately 0.5,
the actual axial displacement of the rollers
is to also be checked.
For additional information, please contact
Table 2
Radial internal clearance of CARB bearings with tapered bore
Bore
diameter
d
over
mm

incl.
C2
min
m
max
Normal
max
m
min
C3
max
m
min
C4
max
m
min
C5
max
m
min
18
24
30
24
30
40
19
23
28
31
37
46
31
37
46
43
51
62
43
51
62
55
65
80
55
65
80
69
81
100
69
81
100
85
99
124
40
50
65
50
65
80
33
42
52
53
63
78
53
63
78
73
88
108
73
88
108
93
113
136
93
113
136
117
148
176
117
148
176
145
183
220
80
100
120
100
120
140
64
75
90
96
115
135
96
115
135
132
155
180
132
155
180
172
201
231
172
201
231
218
255
294
218
255
294
272
321
365
140
160
180
160
180
200
104
118
130
155
173
193
155
173
193
212
238
260
212
238
260
269
301
329
269
301
329
338
382
416
338
382
416
415
469
517
200
225
250
225
250
280
144
161
174
213
235
258
213
235
258
288
315
344
288
315
344
363
401
444
363
401
444
460
511
556
460
511
556
571
635
692
280
315
355
315
355
400
199
233
251
283
318
350
283
318
350
377
419
471
377
419
471
481
542
598
481
542
598
617
679
751
617
679
751
761
848
920
400
450
500
450
500
560
281
305
335
383
435
475
383
435
475
525
575
633
525
575
633
653
733
803
653
733
803
835
911
1005
835
911
1005
1005
1115
1225
560
630
710
630
710
800
380
422
480
530
590
674
530
590
674
702
772
860
702
772
860
886
986
1100
886
986
1100
1100
1230
1380
1100
1230
1380
1350
1490
1660
800
900
1000
900
1000
1120
529
580
645
735
814
895
735
814
895
955
1040
1165
955
1040
1165
1215
1340
1495
1215
1340
1495
1525
1670
1875
1525
1670
1875
1855
2050
2275
1120
1250
705
975
975
1275
1275
1635
1635
2055
2055
2495
174
Loads
Minimum load
In order to provide satisfactory operation,
the CARB, like all ball and roller bearings,
must always be subjected to a given minimum load, particularly if it is to operate at high
speeds or is subjected to high accelerations or
rapid changes in the direction of load. Under
such conditions the inertia forces of the rollers
and cage, and the friction in the lubricant, can
have a detrimental effect on the rolling conditions in the bearing arrangement and may
between the rollers and the raceways.

or similar means.
Equivalent bearing loads

As the CARB can only accept radial loads
P = Fr

Diagram 1
Axial displacement, % of bearing width
Mean radial internal clearance,

% of bearing width
Axial displacement,
% of bearing width
175
CARB
Single row
SKF Explorer
Series: C 2205 TN9 C 2219
Size: 25 mm 95 mm
0.9843 in 3.7402 in
with cage
Designation
Bore
d
mm
in
full complement
suffix V
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
N
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
Axial
displacement
lb
+/- s1)
mm in
C 2205 TN9
C 2205 V
C 2206 TN9
25
25
30
0.9843
0.9843
1.1811
52
52
62
2.0472
2.0472
2.4409
18
18
20
0.7087
0.7087
0.7874
44 000
50 000
69 500
9 900
11 200
15 600
40 000
48 000
62 000
9 000
10 800
13 900
13 000
11 000
18 000
7 000
15 000
0.17
0.18
0.27
0.40
0.40
0.60
5.80
2.80
4.50
0.228
0.110
0.177
C 2206 V
C 2207 TN9
C 2207 V
30
35
35
1.1811
1.3780
1.3780
62
72
72
2.4409
2.8346
2.8346
20
23
23
0.7874
0.9055
0.9055
76 500
83 000
95 000
17 200
18 700
21 400
71 000
80 000
96 000
16 000
18 000
21 600
9 500
-
6 000
13 000
5 000
0.29
0.43
0.45
0.64
0.95
0.99
1.50
5.70
2.70
0.059
0.224
0.106
C 2208 TN9
C 2208 V
C 2209 TN9
40
40
45
1.5748
1.5748
1.7717
80
80
85
3.1496
3.1496
3.3465
23
23
23
0.9055
0.9055
0.9055
90 000
102 000
93 000
20 200
22 900
20 900
86 500
104 000
93 000
19 400
23 400
20 900
8 000
8 000
11 000
4 500
11 000
0.50
0.53
0.55
1.10
1.17
1.21
7.10
4.10
7.10
0.280
0.161
0.280
C 2209 V
C 2210 TN9
C 2210 V
45
50
50
1.7717
1.9685
1.9685
85
90
90
3.3465
3.5433
3.5433
23
23
23
0.9055
0.9055
0.9055
106 000
98 000
114 000
23 800
22 000
25 600
110 000
100 000
122 000
24 700
22 500
27 400
7 000
-
4 300
9 500
3 800
0.58
0.59
0.62
1.28
1.30
1.37
4.10
7.10
3.90
0.161
0.280
0.154
C 2211 TN9
C 2211 V
C 2212 TN9
55
55
60
2.1654
2.1654
2.3622
100
100
110
3.9370
3.9370
4.3307
25
25
28
0.9843
0.9843
1.1024
116 000
132 000
143 000
26 100
29 700
32 100
114 000
134 000
156 000
25 600
30 100
35 100
6 700
5 600
9 000
3 400
7 500
0.79
0.81
1.10
1.74
1.79
2.40
8.60
5.40
8.50
0.339
0.213
0.335
C 2212 V
C 2213 TN9
C 2213 V
60
65
65
2.3622
2.5591
2.5591
110
120
120
4.3307
4.7244
4.7244
28
31
31
1.1024
1.2205
1.2205
166 000
180 000
204 000
37 300
40 500
45 900
190 000
180 000
216 000
42 700
40 500
48 600
5 300
-
2 800
7 500
2 400
1.15
1.40
1.47
2.50
3.10
3.20
5.30
9.60
5.30
0.209
0.378
0.209
C 2214 TN9
C 2214 V
C 2215
70
70
75
2.7559
2.7559
2.9528
125
125
130
4.9213
4.9213
5.1181
31
31
31
1.2205
1.2205
1.2205
186 000
212 000
196 000
41 800
47 700
44 100
196 000
228 000
208 000
44 100
51 300
46 800
5 000
4 800
7 000
2 400
6 700
1.45
1.50
1.60
3.20
3.30
3.50
9.60
5.30
9.60
0.378
0.209
0.378
C 2215 V
C 2216
C 2216 V
75
80
80
2.9528
3.1496
3.1496
130
140
140
5.1181
5.5118
5.5118
31
33
33
1.2205
1.2992
1.2992
220 000
220 000
255 000
49 500
49 500
57 300
240 000
250 000
305 000
54 000
56 200
68 600
4 500
-
2 200
6 000
2 000
1.65
2.00
2.10
3.60
4.40
4.60
5.30
9.10
4.80
0.209
0.358
0.189
C 2217
C 2217 V
C 2218
85
85
90
3.3465
3.3465
3.5433
150
150
160
5.9055
5.9055
6.2992
36
36
40
1.4173
1.4173
1.5748
275 000
315 000
325 000
61 800
70 800
73 100
320 000
390 000
380 000
71 900
87 700
85 400
4 300
3 800
5 600
1 800
5 300
2.60
2.80
3.30
5.70
6.20
7.30
7.10
1.70
9.50
0.280
0.067
0.374
C 2218 V
BSC-2039 V
C 2219
90
90
95
3.5433
3.5433
3.7402
160
150
170
6.2992
5.9055
6.6929
40
72
43
1.5748
2.8346
1.6929
365 000
455 000
360 000
82 100
102 300
80 900
440 000
670 000
400 000
98 900
150 600
89 900
3 800
1 500
1 500
5 000
3.40
5.10
4.00
7.50 5.40
11.20 19.70
8.80 10.50
0.213
0.776
0.413
1) Permissible axial displacement from Normal position of one bearing ring in relation to the other.
176
Single row
SKF Explorer
Series: C 2220 C 2244
Size: 100 mm 220 mm
3.9370 in 8.6614 in
Series: C 2314 C 2320

Size: 70 mm 100 mm
2.7559 in 3.9370 in
Series: C 3022 C 3030 MB

Size: 110 mm 150 mm
4.3307 in 5.9055 in
with cage
Designation
full complement
suffix V
Bore
d
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
Reference Limiting
speed
speed
r/min
r/min
Mass
Axial
displacement
lb
+/- s1)
mm in
4.85
5.95
6.90
10.70
13.10
15.20
10.10 0.398
17.70 0.697
11.10 0.437
4 000
3 800
3 400
8.60
11.00
13.80
19.00
24.30
30.40
13.00 0.512
9.60 0.378
13.70 0.539
2 400
2 000
1 800
3 200
2 600
2 400
17.50
28.00
34.00
38.60
61.70
75.00
11.20 0.441
16.40 0.646
22.50 0.886
562 000
1 500
2 000
56.50
124.60
20.50 0.807
430 000
465 000
550 000
96 700
104 500
123 600
3 800
3 600
3 400
5 000
4 800
4 500
4.25
5.20
6.20
9.40
11.50
13.70
9.10 0.358
13.10 0.516
10.10 0.398
121 400
137 100
137 100
600 000
695 000
695 000
134 900
156 200
156 200
3 200
2 800
2 800
4 300
4 000
4 000
7.30
8.50
10.00
16.10
18.70
22.00
12.10 0.476
9.60 0.378
12.60 0.496
800 000
179 800
880 000
197 800
2 600
3 600
12.50
27.60
11.20 0.441
1.7717
1.8110
1.8110
355 000
375 000
430 000
79 800
84 300
96 700
480 000
530 000
640 000
107 900
119 100
143 900
3 200
3 000
-
4 500
4 000
1 400
3.50
3.90
4.05
7.70
8.60
8.90
9.50 0.374
10.60 0.417
3.80 0.150
2.0472
2.0866
2.2047
390 000
490 000
540 000
87 700
110 200
121 400
585 000
735 000
850 000
131 500
165 200
191 100
2 800
2 600
2 400
3 800
3 400
3 200
5.90
6.30
8.30
13.00
13.90
18.30
16.50 0.650
11.00 0.433
2.80 0.110
mm
in
lbf
C 2220
BSC-2034 V
C 2222
100
100
110
3.9370
3.9370
4.3307
180
170
200
7.0866
6.6929
7.8740
46
65
53
1.8110
2.5591
2.0866
415 000
475 000
530 000
93 300
106 800
119 100
465 000
655 000
620 000
104 500
147 200
139 400
3 600
3 200
4 800
1 300
4 300
C 2224
C 2226
C 2228
120
130
140
4.7244
5.1181
5.5118
215
230
250
8.4646
9.0551
9.8425
58
64
68
2.2835
2.5197
2.6772
610 000
735 000
830 000
137 100
165 200
186 600
710 000
930 000
1 060 000
159 600
209 100
238 300
3 000
2 800
2 400
C 2230
C 2234
C 2238
150
170
190
5.9055
6.6929
7.4803
270
310
340
10.6299
12.2047
13.3858
73
86
92
2.8740
3.3858
3.6220
980 000
1 270 000
1 370 000
220 300
285 500
308 000
1 220 000
1 630 000
1 730 000
274 300
366 400
388 900
C 2244
220
8.6614
400
15.7480
108
4.2520
2 000 000
449 600
2 500 000
C 2314
C 2315
C 2316
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
51
55
58
2.0079
2.1654
2.2835
405 000
425 000
510 000
91 000
95 500
114 600
C 2317
C 2318
C 2319
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866
7.4803
7.8740
60
64
67
2.3622
2.5197
2.6378
540 000
610 000
610 000
C 2320
100
3.9370
215
8.4646
73
2.8740
C 3022
C 3024
C 3024 V
110
120
120
4.3307
4.7244
4.7244
170
180
180
6.6929
7.0866
7.0866
45
46
46
C 3026
C 3028
C 3030 MB
130
140
150
5.1181
5.5118
5.9055
200
210
225
7.8740
8.2677
8.8583
52
53
56
kg
177
CARB
Single row
SKF Explorer
Series: C 3032 C 30/900 M
Size: 160 mm 900 mm
6.2992 in 35.4330 in
with cage
Designation
Bore
d
full complement
suffix V
Basic load ratings
Outside diameter
Width
D
B
mm
in
mm
in
Dynamic
C
N
lbf
mm
in
C 3032
C 3034
C 3036
160
170
180
6.2992
6.6929
7.0866
240
260
280
9.4488
10.2362
11.0236
60
67
74
2.3622
2.6378
2.9134
600 000
750 000
880 000
C 3038
C 3040
C 3044
190
200
220
7.4803
7.8740
8.6614
290
310
340
11.4173
12.2047
13.3858
75
82
90
2.9528
3.2283
3.5433
C 3048
C 3052
C 3056
240
260
280
9.4488
10.2362
11.0236
360
400
420
14.1732
15.7480
16.5354
92
104
106
C 3060 M
C 3064 M
C 3068 M
300
320
340
11.8110
12.5984
13.3858
460
480
520
18.1102
18.8976
20.4724
C 3072 M
C 3076 M
C 3080 M
360
380
400
14.1732
14.9606
15.7480
540
560
600
C 3084 M
C 3088 MB
C 3092 M
420
440
460
16.5354
17.3228
18.1102
C 3096 M
C 30/500 M
C 30/530 M
480
500
530
C 30/560 M
C 30/600 M
C 30/630 M
Speed rating
Static
C0
Reference Limiting
speed
speed
r/min
r/min
Mass
Axial
displacement
kg
lb
+/- s1)
mm in
lbf
134 900
168 600
197 800
980 000
1 160 000
1 340 000
220 300
260 800
301 200
2 200
2 000
1 900
3 000
2 800
2 600
9.60
12.50
16.50
21.20 15.00 0.591

27.60 12.50 0.492
36.40 15.10 0.594
930 000
1 120 000
1 320 000
209 100
251 800
296 700
1 460 000
1 730 000
2 040 000
328 200
388 900
458 600
1 800
1 700
1 600
2 400
2 400
2 200
17.50
22.00
29.00
38.60 16.10 0.634

48.50 15.20 0.598
63.90 17.20 0.677
3.6220
4.0945
4.1732
1 340 000
1 760 000
1 860 000
301 200
395 600
418 100
2 160 000
2 850 000
3 100 000
485 600
640 700
696 900
1 400
1 300
1 200
2 000
1 800
1 600
31.50
46.00
50.00
69.40 19.20 0.756

101.40 19.30 0.760
110.20 21.30 0.839
118
121
133
4.6457
4.7638
5.2362
2 160 000
2 280 000
2 900 000
485 600
512 500
651 900
3 750 000
4 000 000
5 000 000
843 000
899 200
1 124 000
1 100
1 000
950
1 500
1 400
1 300
71.00
76.50
100.00
156.50 20.00 0.787

168.70 23.30 0.917
220.50 25.40 1.000
21.2598
22.0472
23.6220
134
135
148
5.2756
5.3150
5.8268
2 900 000
3 000 000
3 650 000
651 900
674 400
820 500
5 000 000
5 200 000
6 200 000
1 124 000
1 169 000
1 393 800
900
900
800
1 200
1 200
1 100
105.00
110.00
140.00
231.50 26.40 1.039

242.50 27.00 1.063
308.60 30.60 1.205
620
650
680
24.4094
25.5906
26.7717
150
157
163
5.9055
6.1811
6.4173
3 800 000
3 750 000
4 000 000
854 200
843 000
899 200
6 400 000
6 400 000
7 500 000
1 438 700
1 438 700
1 686 000
800
750
700
1 100
1 000
950
150.00
185.00
200.00
330.70 32.60 1.283

407.90 19.70 0.776
440.90 33.50 1.319
18.8976
19.6850
20.8661
700
720
780
27.5591
28.3465
30.7087
165
167
185
6.4961
6.5748
7.2835
4 050 000
4 250 000
5 100 000
910 400
955 400
1 146 500
7 800 000
8 300 000
9 500 000
1 753 400
1 865 800
2 135 600
670
630
600
900
900
800
210.00
225.00
295.00
463.00 35.50 1.398

496.00 37.50 1.476
650.40 35.70 1.406
560
600
630
22.0472
23.6220
24.8031
820
870
920
32.2835
34.2520
36.2204
195
200
212
7.6772
7.8740
8.3464
5 600 000
6 300 000
6 800 000
1 258 900
1 416 200
1 528 600
11 000 000
12 200 000
12 900 000
2 472 800
2 742 600
2 899 900
530
500
480
750
700
670
345.00
390.00
465.00
760.60 45.70 1.799

859.80 35.90 1.413
1025.10 48.10 1.894
C 30/670 M
C 30/710 M
C 30/750 MB
670
710
750
26.3780 980
27.9527 1030
29.5275 1090
38.5827
40.5511
42.9133
230
236
250
9.0551
9.2913
9.8425
8 150 000
8 800 000
9 000 000
1 832 100
1 978 200
2 023 200
16 300 000
17 300 000
18 000 000
3 664 200
3 889 000
4 046 400
430
400
380
600
560
530
580.00
645.00
770.00
1278.70 41.10 1.618

1422.00 47.30 1.862
1697.50 25.00 0.984
C 30/800 MB
C 30/850 MB
C 30/900 M
800
850
900
31.4960 1150
33.4645 1220
35.4330 1280
45.2755
48.0314
50.3936
258
272
280
10.1575
10.7086
11.0236
9 150 000
11 200 000
12 700 000
2 056 900
2 517 800
2 855 000
18 600 000
24 000 000
26 500 000
4 181 300
5 395 200
5 957 200
360
320
300
480 860.00
430 1050.00
400 1150.00
1896.00 25.00 0.984

2314.80 27.00 1.063
2535.30 45.80 1.803
178
Single row
SKF Explorer
Series: C 30/950 MB C 30/1250 MB
37.4015 in 49.2125 in
with cage
full complement
suffix V
Designation
Bore
d
mm
C 30/950 MB
C 30/1000 MB
C 30/1250 MB
Series: C 3120 C 31/530 M

Size: 100 mm 530 mm
3.9370 in 20.8661 in
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
300 11.8110 12 900 000 2 899 900 27 500 000 6 182 000
308 12.1260 13 400 000 3 012 300 29 000 000 6 519 200
375 14.7638 20 400 000 4 585 900 45 000 000 10 116 000
Reference Limiting
speed speed
r/min r/min
280
260
180
Mass
kg
380 1410.00
340 1570.00
240 2740.00
Axial
displacement
lb
+/- s1)
mm in
3108.50
3461.20
6040.60
30.00 1.181
30.00 1.181
37.00 1.457
950
1000
1250
37.4015
39.3700
49.2125
1360
1420
1750
53.5432
55.9054
68.8975
C 3120
C 3120 V
C 3130
100
100
150
3.9370
3.9370
5.9055
165
165
250
6.4961
6.4961
9.8425
52
52
80
2.0472
2.0472
3.1496
415 000
475 000
880 000
93 300
106 800
197 800
540 000
655 000
1 290 000
121 400
147 200
290 000
3 200
2 000
4 300
1 300
2 800
4.40
4.40
15.00
9.70
9.70
33.10
10.00 0.394
4.70 0.185
13.90 0.547
C 3132
C 3134
C 3136
160
170
180
6.2992
6.6929
7.0866
270
280
300
10.6299
11.0236
11.8110
86
88
96
3.3858
3.4646
3.7795
1 000 000
1 040 000
1 250 000
224 800
233 800
281 000
1 400 000
1 460 000
1 730 000
314 700
328 200
388 900
2 000
1 900
1 800
2 600
2 600
2 400
20.00
21.00
26.00
44.10
46.30
57.30
19.00 0.748
21.00 0.827
23.20 0.913
C 3138
C 3140
C 3144
190
200
220
7.4803
7.8740
8.6614
320
340
370
12.5984
13.3858
14.5669
104
112
120
4.0945
4.4094
4.7244
1 530 000
1 560 000
1 900 000
343 900
350 700
427 100
2 200 000
2 320 000
2 900 000
494 600
521 500
651 900
1 600
1 500
1 400
2 200
2 000
1 900
33.50
40.00
51.00
73.90
88.20
112.40
19.00 0.748
27.30 1.075
22.30 0.878
C 3148
C 3152
C 3156
240
260
280
9.4488
10.2362
11.0236
400
440
460
15.7480
17.3228
18.1102
128
144
146
5.0394
5.6693
5.7480
2 320 000
2 650 000
2 850 000
521 500
595 700
640 700
3 450 000
4 050 000
4 500 000
775 600
910 400
1 011 600
1 300
1 100
1 100
1 700
1 500
1 400
63.00
87.00
93.00
138.90
191.80
205.00
20.40 0.803
26.40 1.039
28.40 1.118
C 3160
C 3164 M
C 3168 M
300
320
340
11.8110
12.5984
13.3858
500
540
580
19.6850
21.2598
22.8346
160
176
190
6.2992
6.9291
7.4803
3 250 000 730 600

4 150 000 932 900
4 900 000 1 101 500
5 200 000
6 300 000
7 500 000
1 169 000
1 416 200
1 686 000
1 000
950
850
1 300
1 300
1 200
120.00
160.00
205.00
264.60
352.70
451.90
30.50 1.201
26.70 1.051
25.90 1.020
C 3172 M
C 3176 MB
C 3180 MB
360
380
400
14.1732
14.9606
15.7480
600
620
650
23.6220
24.4094
25.5905
192
194
200
7.5590
7.6378
7.8740
5 000 000 1 124 000

4 550 000 1 022 800
5 000 000 1 124 000
8 000 000
7 500 000
8 650 000
1 798 400
1 686 000
1 944 500
800
750
700
1 100
1 000
950
215.00
230.00
275.00
474.00
507.10
606.30
27.90 1.098
19.00 0.748
10.10 0.398
C 3184 M
C 3188 MB
C 3192 M
420
440
460
16.5354
17.3228
18.1102
700
720
760
27.5591
28.3464
29.9212
224
226
240
8.8189
8.8976
9.4488
6 000 000 1 348 800 10 400 000

5 700 000 1 281 400 9 300 000
6 800 000 1 528 600 12 000 000
2 337 900
2 090 600
2 697 600
670
670
600
900
900
800
340.00
360.00
430.00
749.60
793.70
948.00
34.80 1.370
22.00 0.866
51.00 2.008
C 3196 MB
C 31/500 M
C 31/530 M
480
500
530
18.8976
19.6850
20.8661
790
830
870
31.1023
32.6771
34.2520
248 9.7638
264 10.3937
272 10.7087
6 950 000 1 562 400 12 500 000

7 500 000 1 686 000 12 700 000
8 800 000 1 978 200 15 600 000
2 810 000
2 855 000
3 506 900
560
530
500
750
750
670
490.00
550.00
630.00
1080.30
1212.50
1388.90
24.00 0.945
75.30 2.965
44.40 1.748
179
CARB
Single row
SKF Explorer
Series: C 31/560 MB C 31/1000 MB
22.0472 in 39.3700 in
Series: C 3224 C 3236

Size: 120 mm 180 mm
4.7244 in 7.0866 in
Series: C 3972 M C 39/630 M

Size: 360 mm 630 mm
14.1732 in 24.8031 in
with cage
Designation
Bore
d
Outside diameter
D
mm
in
full complement
suffix V
Basic load ratings
Width
B
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
Mass
Reference Limiting
speed speed
r/min r/min
Axial
displacement
lb
+/- s1)
mm in
750.00
870.00
1040.00
1653.50
1918.00
2292.80
28.00 1.102
30.00 1.181
31.00 1.220
530
480
450
1230.00
1410.00
1700.00
2711.70
3108.50
3747.80
33.00 1.299
34.00 1.339
36.00 1.417
400
380
300
1870.00
2260.00
3470.00
4122.60
4982.40
7650.00
37.00 1.457
40.00 1.575
46.00 1.811
980 000
1 830 000
2 200 000
220 300 2 400 3 200

411 400 1 700 2 400
494 600 1 500 2 000
11.50
28.50
37.00
25.40
62.80
81.60
17.10 0.673
19.30 0.760
27.30 1.075
395 600
476 600
485 600
3 250 000
4 000 000
4 150 000
730 600 1 000 1 400

899 200
950 1 300
932 900
900 1 300
44.00
65.50
69.00
97.00
144.40
152.10
17.20 0.677
10.00 0.394
10.00 0.394
2 160 000
2 750 000
2 700 000
485 600
618 200
607 000
4 250 000
5 300 000
5 300 000
955 400
1 191 400
1 191 400
850 1 200
800 1 100
800 1 100
71.00
98.00
100.00
156.50
216.10
220.50
21.30 0.839
11.00 0.433
11.00 0.433
5.0394
5.0394
5.3543
3 100 000
3 150 000
3 550 000
696 900
708 100
798 000
6 100 000
6 300 000
7 100 000
1 371 300
1 416 200
1 596 100
750 1 000
700 950
670 900
120.00
125.00
150.00
264.60
275.60
330.70
20.40 0.803
20.40 0.803
28.40 1.118
5.5118
5.9055
6.4961
3 600 000
809 300 7 350 000
4 000 000
899 200 8 800 000
4 650 000 1 045 300 10 000 000
1 652 300
1 978 200
2 248 000
600
560
530
170.00
210.00
270.00
374.80
463.00
595.20
32.40 1.276
32.40 1.276
35.50 1.398
mm
in
lbf
C 31/560 MB
C 31/600 MB
C 31/630 MB
560
600
630
22.0472
23.6220
24.8031
920
980
1030
36.2204
38.5826
40.5511
280
300
315
11.0236 9 500 000 2 135 600 17 000 000

11.8110 10 200 000 2 293 000 18 000 000
12.4016 12 200 000 2 742 600 22 000 000
3 821 600
4 046 400
4 945 600
480
430
400
670
600
560
C 31/670 MB
C 31/710 MB
C 31/750 MB
670
710
750
26.3779
27.9527
29.5275
1090
1150
1220
42.9133
45.2755
48.0314
336
345
365
13.2283 12 000 000 2 697 600 22 000 000

13.5827 12 700 000 2 855 000 24 000 000
14.3701 16 000 000 3 596 800 30 500 000
4 945 600
5 395 200
6 856 400
380
360
320
C 31/800 MB
C 31/850 MB
C 31/1000 MB
800
850
1000
31.4960
33.4645
39.3700
1280
1360
1580
50.3936
53.5432
62.2046
375
400
462
14.7638 15 600 000 3 506 900 30 500 000 6 856 400

15.7480 16 000 000 3 596 800 32 000 000 7 193 600
18.1889 22 800 000 5 125 400 45 500 000 10 228 400
300
280
220
C 3224
C 3232
C 3236
120
160
180
4.7244
6.2992
7.0866
215
290
320
8.4646
11.4173
12.5984
76
104
112
2.9921
4.0945
4.4094
750 000
1 370 000
1 530 000
168 600
308 000
343 900
C 3972 M
C 3976 MB
C 3980 MB
360
380
400
14.1732
14.9606
15.7480
480
520
540
18.8976
20.4724
21.2598
90
106
106
3.5433
4.1732
4.1732
1 760 000
2 120 000
2 160 000
C 3984 M
C 3988 MB
C 3992 MB
420
440
460
16.5354
17.3228
18.1102
560
600
620
22.0472
23.6220
24.4094
106
118
118
4.1732
4.6457
4.6457
C 3996 M
C 39/500 M
C 39/530 M
480
500
530
18.8976
19.6850
20.8661
650
670
710
25.5905
26.3780
27.9527
128
128
136
C 39/560 M
C 39/600 M
C 39/630 M
560
600
630
22.0472
23.6220
24.8031
750
800
850
29.5275
31.4960
33.4646
140
150
165
850
750
700
kg
180
Single row
SKF Explorer
Series: C 39/670 M C 39/1180 M
26.3780 in 46.4566 in
Series: C 4010 TN9 C 4040 V

Size: 50 mm 200 mm
1.9685 in 7.8740 in
with cage
full complement
suffix V
Designation
Shaft dia.
d1
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Mass
Reference Limiting
speed speed
r/min
r/min
kg
Axial
displacement
lb
+/- s1)
mm in
C 39/670 M
C 39/710 M
C 39/750 M
670
710
750
26.3780
27.9528
29.5276
900
950
1 000
35.4331
37.4016
39.3701
170
180
185
6.6929
7.0866
7.2835
4 900 000 1 101 500 11 200 000 2 517 800

6 000 000 1 348 800 12 500 000 2 810 000
6 100 000 1 371 300 13 400 000 3 012 300
480
450
430
630
630
560
310.00
355.00
405.00
683.40
782.60
892.90
40.50
30.70
35.70
1.594
1.209
1.406
C 39/800 M
C 39/850 M
C 39/900 MB
800
850
900
31.4960
33.4646
35.4330
1060
1 120
1180
41.7322
44.0945
46.4566
195
200
206
7.6772
7.8740
8.1102
6 400 000 1 438 700 14 600 000 3 282 100

7 350 000 1 652 300 16 300 000 3 664 200
8 150 000 1 832 100 18 000 000 4 046 400
380
360
340
530
480
450
470.00
530.00
580.00
1036.20
1168.40
1278.70
45.70
35.90
20.00
1.799
1.413
0.787
C 39/950 M
C 39/1060 MB
C 39/1180 M
950
1060
1180
37.4015
41.7322
46.4566
1250
1400
1540
49.2125
55.1180
60.6298
224
250
272
8.8189 9 300 000 2 090 600 22 000 000 4 945 600

9.8425 12 500 000 2 810 000 29 000 000 6 519 200
10.7086 12 900 000 2 899 900 31 500 000 7 081 200
300
260
220
430 745.00
340 1040.00
300 1340.00
1642.40
2292.80
2954.20
35.00
25.00
44.40
1.378
0.984
1.748
50
50
65
1.9685
1.9685
2.5591
80
80
100
3.1496
3.1496
3.9370
30
30
35
1.1811
1.1811
1.3780
116 000
137 000
196 000
26 100
30 800
44 100
140 000
176 000
275 000
0.55
0.59
1.00
1.20
1.30
2.20
6.00
3.00
2.80
0.236
0.118
0.110
C 4015 V
C 4020 V
C 4022 V
75
100
110
2.9528
3.9370
4.3307
115
150
170
4.5276
5.9055
6.6929
40
50
60
1.5748
1.9685
2.3622
236 000
355 000
500 000
53 100
79 800
112 400
345 000
530 000
800 000
77 600
119 100
179 800
- 2 000
- 1 400
- 1 200
1.50
3.05
5.15
3.30
6.70
11.40
5.10
9.70
6.60
0.201
0.382
0.260
C 4024 V
C 4024 V/VE240
C 4026
120
120
130
4.7244
4.7244
5.1181
180
180
200
7.0866
7.0866
7.8740
60
60
69
2.3622
2.3622
2.7165
530 000
430 000
620 000
119 100
96 700
139 400
880 000
640 000
930 000
197 800
- 1 100
143 900
1 000
209 100 1 900 2 800
5.50
5.70
7.84
12.10
12.60
17.30
5.20
6.00
11.40
0.205
0.236
0.449
C 4026 V
C 4028 V
C 4030 V
130
140
150
5.1181
5.5118
5.9055
200
210
225
7.8740
8.2677
8.8583
69
69
75
2.7165
2.7165
2.9528
720 000
750 000
780 000
161 900
168 600
175 300
1 120 000
1 220 000
1 320 000
251 800
274 300
296 700
850
800
750
8.05
8.55
10.50
17.70
18.80
23.10
4.60
5.90
10.60
0.181
0.232
0.417
C 4032
C 4032 V
C 4034 V
160
160
170
6.2992
6.2992
6.6929
240
240
260
9.4488
9.4488
10.2362
80
80
90
3.1496
3.1496
3.5433
795 000
915 000
1 140 000
178 700
205 700
256 300
1 160 000
1 460 000
1 860 000
260 800 1 600 2 400

328 200
600
418 100
480
12.80
12.60
17.50
28.20
27.80
38.60
18.10
8.20
7.20
0.713
0.323
0.283
C 4036 V
C 4038 V
C 4040 V
180
190
200
7.0866
7.4803
7.8740
280
290
310
11.0236
11.4173
12.2047
100
100
109
3.9370
3.9370
4.2913
1 320 000
1 370 000
1 630 000
296 700
308 000
366 400
2 120 000
2 320 000
2 650 000
476 600
521 500
595 700
23.00
24.50
30.50
50.70
54.00
67.20
10.20
10.10
11.10
0.402
0.398
0.437
C 4010 TN9
C 4010 V
C 4013 V
31 500 5 000 7 500

39 600
- 3 000
61 800
- 2 400
430
380
260
181
CARB
Single row
SKF Explorer
Series: C 4044 V C 40/710 M
Size: 220 mm 710 mm
8.6614 in 27.9527 in
Series: C 4120 V/VE240 C 41/500 MB

Size: 100 mm 500 mm
3.9370 in 19.6850 in
Series: C 4908 V C 4916 V

Size: 40 mm 80 mm
1.5748 in 3.1496 in
with cage
Designation
Shaft dia. Outside diameter
d1
D
mm
in
mm
in
full complement
suffix V
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
C 4044 V
C 4060 M
C 40/710 M
220
300
710
8.6614
11.8110
27.9527
340
460
1030
13.3858
18.1102
40.5511
118
160
315
C 4120 V/VE240
C 4122 V
C 4124 V
100
110
120
3.9370
4.3307
4.7244
165
180
200
6.4961
7.0866
7.8740
65
69
80
2.5591
2.7165
3.1496
475 000
670 000
780 000
106 800
150 600
175 300
C 4128 V
C 4130 V
C 4132 V
140
150
160
5.5118
5.9055
6.2992
225
250
270
8.8583
9.8425
10.6299
85
100
109
3.3465
3.9370
4.2913
1 000 000
1 220 000
1 460 000
C 4134 V
C 4136 V
C 4138 V
170
180
190
6.6929
7.0866
7.4803
280
300
320
11.0236
11.8110
12.5984
109
118
128
4.2913
4.6457
5.0394
1 530 000
1 760 000
2 040 000
C 4140 V
C 4192 M
C 41/500 MB
200
460
500
7.8740
18.1102
19.6850
340
760
830
13.3858
29.9212
32.6771
140
300
325
5.5118
11.8110
12.7953
C 4908 V
C 4909 V
C 4910 V
40
45
50
1.5748
1.7717
1.9685
62
68
72
2.4409
2.6772
2.8346
22
22
22
0.8661
0.8661
0.8661
76 500
81 500
86 500
17 200
18 300
19 400
C 4911 V
C 4912 V
C 4913 V
55
60
65
2.1654
2.3622
2.5591
80
85
90
3.1496
3.3465
3.5433
25
25
25
0.9843
0.9843
0.9843
106 000
112 000
116 000
C 4914 V
C 4915 V
C 4916 V
70
75
80
2.7559
2.9528
3.1496
100
105
110
3.9370
4.1339
4.3307
30
30
30
1.1811
1.1811
1.1811
163 000
166 000
173 000
4.6457 1 930 000 433 900 3 250 000

6.2992 2 900 000 651 900 4 900 000
12.4016 10 600 000 2 382 900 21 600 000
lbf
Reference Limiting
speed
speed
r/min
r/min
Mass
kg
Axial
displacement
lb
730 600
1 101 500
4 855 700
850
320
200 40.00
88.20 10.10 0.398
1 200 95.00 209.40 30.40 1.197
430 860.00 1896.00 51.20 2.016
655 000
1 000 000
1 120 000
147 200
224 800
251 800
1 300
900
750
5.25
7.05
10.50
11.60 17.70 0.697

15.50 4.60 0.181
23.10 11.20 0.441
224 800
274 300
328 200
1 600 000
1 860 000
2 160 000
359 700
418 100
485 600
630
450
300
14.20
20.50
26.00
31.30 5.20 0.205

45.20 10.10 0.398
57.30 11.10 0.437
343 900
395 600
458 600
2 280 000
2 700 000
3 150 000
512 500
607 000
708 100
280
220
130
27.00
34.50
43.00
59.50 11.10 0.437

76.10 10.10 0.398
94.80 10.10 0.398
2 360 000 530 500 3 650 000

8 300 000 1 865 800 14 300 000
9 800 000 2 203 000 17 600 000
820 500
3 214 600
3 956 500
480
400
100 000
112 000
125 000
22 500
25 200
28 100
4 300
3 800
3 600
0.25
0.30
0.29
0.60
0.70
0.60
1.70 0.067
1.70 0.067
1.70 0.067
23 800
25 200
26 100
153 000
170 000
180 000
34 400
38 200
40 500
3 200
3 000
2 800
0.43
0.46
0.50
0.90
1.00
1.10
2.50 0.098
2.30 0.091
2.30 0.091
36 600
37 300
38 900
240 000
255 000
275 000
54 000
57 300
61 800
2 600
2 400
2 200
0.78
0.82
0.87
1.70
1.80
1.90
2.80 0.110
2.80 0.110
1.70 0.067
80 54.00 119.00 12.10 0.476

630 535.00 1179.50 46.20 1.819
560 720.00 1587.30 16.30 0.642
182
+/- s1)
mm
in
Single row
SKF Explorer
Size: 85 mm 100 mm 3.3465 in 3.9370 in
Series: C 5020 V Size: 100 mm 3.9370 in

Size: 40 mm 100 mm 1.5748 in 3.9370 in
Series: C 6006 V Size: 30 mm 1.1811 in

Size: 40 mm 70 mm 1.5748 in 2.7559 in
with cage
Designation
full complement
suffix V
Shaft dia.
d1
mm
in
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Axial
displacement
lb
+/- s1)
mm
in
C 4917 V
C 4918 V
C 4920 V
85
90
100
3.3465
3.5433
3.9370
120
125
140
4.7244
4.9213
5.5118
35
35
40
1.3780
1.3780
1.5748
224 000
186 000
275 000
50 400
41 800
61 800
355 000
315 000
450 000
79 800
70 800
101 200
2 000
2 000
1 700
1.30
1.30
1.90
2.90
2.90
4.20
1.70 0.067
6.70 0.264
5.10 0.201
C 5020 V
100
3.9370
150
5.9055
67
2.6378
510 000
114 600
865 000
194 500
1 100
4.30
9.50
5.00 0.197
C 5908 V
C 5909 V
C 5910 V
40
45
50
1.5748
1.7717
1.9685
62
68
72
2.4409
2.6772
2.8346
30
30
30
1.1811
1.1811
1.1811
104 000
110 000
118 000
23 400
24 700
26 500
143 000
163 000
180 000
32 100
36 600
40 500
3 400
3 200
2 800
0.35
0.41
0.42
0.80
0.90
0.90
2.00 0.079
2.00 0.079
2.00 0.079
C 5911 V
C 5912 V
C 5913 V
55
60
65
2.1654
2.3622
2.5591
80
85
90
3.1496
3.3465
3.5433
34
34
34
1.3386
1.3386
1.3386
143 000
150 000
156 000
32 100
33 700
35 100
224 000
240 000
260 000
50 400
54 000
58 400
2 600
2 400
2 200
0.60
0.64
0.70
1.30
1.40
1.50
3.00 0.118
2.80 0.110
2.80 0.110
C 5914 V
C 5915 V
C 5916 V
70
75
80
2.7559
2.9528
3.1496
100
105
110
3.9370
4.1339
4.3307
40
40
40
1.5748
1.5748
1.5748
196 000
204 000
208 000
44 100
45 900
46 800
310 000
325 000
345 000
69 700
73 100
77 600
2 000
1 900
1 800
1.00
1.10
1.20
2.20
2.40
2.60
6.20 0.244
6.20 0.244
5.10 0.201
C 5917 V
C 5918 V
C 5920 V
85
90
100
3.3465
3.5433
3.9370
120
125
140
4.7244
4.9213
5.5118
46
46
54
1.8110
1.8110
2.1260
275 000
224 000
375 000
61 800
50 400
84 300
465 000
400 000
640 000
104 500
89 900
143 900
1 700
1 600
1 400
1.70
1.75
2.70
3.70 4.60 0.181

3.90 11.10 0.437
6.00 4.70 0.185
C 6006 V
30
1.1811
55
2.1654
45
1.7717
134 000
30 100
180 000
40 500
3 000
0.50
1.10
4.90 0.193
C 6908 V
C 6909 V
C 6910 V
40
45
50
1.5748
1.7717
1.9685
62
68
72
2.4409
2.6772
2.8346
40
40
40
1.5748
1.5748
1.5748
122 000
132 000
140 000
27 400
29 700
31 500
180 000
200 000
224 000
40 500
45 000
50 400
2 800
2 600
2 200
0.47
0.55
0.54
1.00
1.20
1.20
6.40 0.252
6.40 0.252
6.40 0.252
C 6911 V
C 6912 V
C 6913 V
55
60
65
2.1654
2.3622
2.5591
80
85
90
3.1496
3.3465
3.5433
45
45
45
1.7717
1.7717
1.7717
180 000
190 000
196 000
40 500
42 700
44 100
300 000
335 000
355 000
67 400
75 300
79 800
2 000
1 900
1 800
0.81
0.84
0.93
1.80
1.90
2.10
4.90 0.193
4.70 0.185
4.70 0.185
C 6914 V
70
2.7559
100
3.9370
54
2.1260
265 000
59 600
455 000
102 300
1 700
1.40
3.10
5.80 0.228
183
CARB
Single row
SKF Explorer
Sealed
Series: C 4013-2CS5V C 4040-2CS5V
Size: 65 mm 200 mm
2.5591 in 7.8740.9055

Size: 100 mm 200 mm
3.9370 in 7.8740 in
d1
Series: C 5918-2CS5V Size: 90 mm 3.5433 in

Size: 50 mm 75 mm
1.9685 in 2.9528 in
Designation
Shaft dia. Outside diameter
d1
D
mm
in
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Mass
Reference Limiting
speed speed
r/min r/min
kg
Axial
displacement
lb
+/- s1)
mm
in
C 4013-2CS5V
C 4015-2CS5V
C 4020-2CS5V
65
75
100
2.5591
2.9528
3.9370
100
115
150
3.9370
4.5276
5.9055
35 1.3780
40 1.5748
50 1.9685
102 000
143 000
310 000
22 900
32 100
69 700
173 000
193 000
450 000
38 900
43 400
101 200
150
130
95
1.10
1.40
2.90
2.40
3.10
6.40
5.90
7.30
6.20
0.232
0.287
0.244
C 4022-2CS5V
C 4024-2CS5V
C 4026-2CS5V
110
120
130
4.3307
4.7244
5.1181
170
180
200
6.6929
7.0866
7.8740
60 2.3622
60 2.3622
69 2.7165
415 000
430 000
550 000
93 300
96 700
123 600
585 000
640 000
830 000
131 500
143 900
186 600
85
80
70
4.60
5.10
7.50
10.10
11.20
16.50
7.90
7.50
8.20
0.311
0.295
0.323
C 4028-2CS5V
C 4030-2CS5V
C 4032-2CS5V
140
150
160
5.5118
5.9055
6.2992
210
225
240
8.2677
8.8583
9.4488
69 2.7165
75 2.9528
80 3.1496
570 000
585 000
655 000
128 100
900 000
131 500
965 000
147 200 1 100 000
202 300
216 900
247 300
67
63
60
7.90
10.00
12.00
17.40 8.70
22.00 10.80
26.50 11.40
0.343
0.425
0.449
C 4034-2CS5V
C 4036-2CS5V
C 4038-2CS5V
170
180
190
6.6929
7.0866
7.4803
260
280
290
10.2362
11.0236
11.4173
90 3.5433
965 000
100 3.9370 1 320 000
100 3.9370 1 370 000
216 900 1 630 000

296 700 2 120 000
308 000 2 320 000
366 400
476 600
521 500
53
53
48
17.00
23.50
24.50
37.50
51.80
54.00
9.00
6.40
6.40
0.354
0.252
0.252
C 4040-2CS5V
200
7.8740
310
12.2047
109 4.2913 1 630 000
366 400 2 650 000
595 700
45
31.00
68.30
6.70
0.264
C 4120-2CS5V
C 4122-2CS5V
C 4124-2CS5V
100
110
120
3.9370
4.3307
4.7244
165
180
200
6.4961
7.0866
7.8740
475 000
500 000
710 000
106 800
655 000
112 400
710 000
159 600 1 000 000
147 200
159 600
224 800
90
85
75
5.20
6.60
9.70
11.50
14.60
21.40
7.30
8.20
8.20
0.287
0.323
0.323
C 4126-2CS5V
C 4128-2CS5V
C 4130-2CS5V
130
140
150
5.1181
5.5118
5.9055
210
225
250
8.2677
8.8583
9.8425
80 3.1496
750 000
85 3.3465
780 000
100 3.9370 1 220 000
168 600 1 100 000

175 300 1 200 000
274 300 1 860 000
247 300
269 800
418 100
70
63
60
10.50
12.50
20.50
23.10
27.60
45.20
7.50
8.90
6.40
0.295
0.350
0.252
C 4132-2CS5V
C 4134-2CS5V
C 4136-2CS5V
160
170
180
6.2992
6.6929
7.0866
270
280
300
10.6299
11.0236
11.8110
109 4.2913 1 460 000

109 4.2913 1 530 000
118 4.6457 1 760 000
328 200 2 160 000

343 900 2 280 000
395 600 2 700 000
485 600
512 500
607 000
53
53
48
26.00
27.00
35.00
57.30
59.50
77.20
6.70
6.70
6.40
0.264
0.264
0.252
C 4138-2CS5V
C 4140-2CS5V
190
200
7.4803
7.8740
320
340
12.5984
13.3858
128 5.0394 2 040 000

140 5.5118 2 360 000
458 600 3 150 000

530 500 3 650 000
708 100
820 500
45
43
43.50 95.90
54.50 120.20
6.40
7.00
0.252
0.276
C 5918-2CS5V
90
3.5433
125
4.9213
46 1.8110
224 000
50 400
400 000
89 900
110
1.75
3.90
4.50
0.177
C 6910-2CS5V
C 6912-2CS5V
C 6912-2NSV
50
60
60
1.9685
2.3622
2.3622
72
85
85
2.8346
3.3465
3.3465
40 1.5748
45 1.7717
45 1.7717
140 000
150 000
190 000
31 500
33 700
42 700
224 000
240 000
335 000
50 400
54 000
75 300
200
170
-
0.56
0.83
0.85
1.20
1.80
1.90
2.80
5.40
0.50
0.110
0.213
0.020
C 6915-2CS5V
75
2.9528
105
4.1339
54 2.1260
204 000
45 900
325 000
73 100
140
1.40
3.10
7.10
0.280
65 2.5591
69 2.7165
80 3.1496
184
Needle roller
bearings
Nomenclature
RNA 4900 2RS M V C3

1
3
2
5
4
1. Basic design:
2. Seals, shields and snap rings:
5. Clearance and tolerance:
HK
Drawn cup needle roller with

open ends
RS
Seal of plate and synthetic

rubber on one side
(C0)*

clearance
NA
Bearing with flanges and

inner ring
2RS
Seal of plate and synthetic

rubber on both sides
C3

> normal
NK
Bearing with flanges

without inner ring
C4

> C3
NKI

inner rings
CNR
NKIS

inner rings
3. Cage designs:
Reduced normal radial

clearance corresponding to
earlier standard
(ISO 5753-1981)
NKS
TN
P5
Bearing with flanges

without inner ring
Nylon cage, rolling element

guided
RNA
Bearing without inner ring
Dimensional and running

accuracy to ISO tolerance
class 5 specifications
(better than P6)

P6
Dimensional and running

accuracy to ISO tolerance
class 6 specifications
(better than normal)
IS1
One lubrication hole in the

inner ring
4. Features:
V

without cage
H...
Reduced tolerance for the

inside diameter of the roller
and cage assembly; the figures
following the letter H indicate
the tolerance limits in mm
* Not marked on bearing or package
185
Needle roller bearings
Product
Details
Technical
features
Boundary dimensions

(ABMA std 18.1)
Tolerances
Normal
Heat stabilization
302 F (150 C)
Misalignment
None to very minor

(contact SKF for further details)
Cage Material
Drawn cup needle

roller bearing
with open ends
186
Standard
Steel
Optional
Polyamide (TN)
Axial load max
None
Seals
2RS1 - 2 synthetic rubber (NBR) seals only

available on RNA 49 and NA 49 series
Needle roller bearing

with inner ring
Needle roller bearing

without inner ring
Introduction
Introduction
Needle roller bearings are roller bearings with
cylindrical rollers, which are thin and long in
relation to their diameter. They are referred to
as needle rollers. In spite of their low cross
section, the bearings have a high load carrying
capacity and are thus eminently suitable for
bearing arrangements where radial space is
limited.
The needle rollers have a profile, which is
slightly relieved towards the roller ends. The
resultant modified line contact between needle
rollers and raceways means that damaging
edge stresses are minimized.
SKF supplies many different types of needle
roller bearings, including drawn cup needle
roller bearings with open ends and with closed
ends, and needle roller bearings with and
without inner rings.
Basic design
Needle roller bearings with carbon chromium
steel rings have a low sectional height and
very high load carrying capacity. Depending
on the application, they may be used with or
without an inner ring.
Needle roller bearings without inner ring
are the better alternative where it is possible
to harden and grind the necessary raceways
on the shaft. As the inner ring is not needed
the shaft can have a larger diameter and will
therefore be stiffer. The amount by which the
shaft can be axially displaced relative to the
housing is also only limited by the width of
the raceway on the shaft. By machining the
shaft raceways to appropriate accuracies of
dimension and form, it is possible to achieve
bearing arrangements having enhanced
running accuracy.
Needle roller bearings with inner ring are
used for arrangements where it is impossible,
or uneconomical, to harden and grind the
shaft. Bearings with inner ring only permit
axial displacements of the shaft relative to the
housing within the limits quoted in the bearing
tables. If greater displacements have to be
accommodated, extended inner rings can be
used instead of the standard inner rings. For
details on these extended rings, please consult
Drawn cup needle roller bearings

Drawn cup needle roller bearings are needle
roller bearings with thin, deep drawn outer
rings. Their principal characteristics are their
very low cross section and their high load
carrying capacity. They are mainly used where
particularly compact and economic bearing
arrangements are desired but where the
housing bore cannot serve as a raceway for a
needle roller and cage assembly. The bearings
must be mounted with an interference fit in
the housing. If axial location by means of
shoulders, snap rings, etc. is dispensed with,
the housing bores can be produced simply and
economically.
Drawn cup needle roller bearings are available with open ends (Figure 1a), or with one
closed end (Figure 1b) for mounting on shaft
ends. The profiled base (end) of the closed
drawn cup enables minor axial guiding forces to
be accommodated.
Drawn cup needle roller bearings are generally used without an inner ring. For applications
where it is not possible to harden and grind the
shaft seating, the inner rings listed in the tables
can be used.
The outer ring of hardened sheet steel and
the needle roller and cage assembly of drawn
cup needle roller bearings form a non-separable unit. The free space available for lubricant
means that long relubrication intervals can
be applied. The bearings are generally of the
single row design with the exception of the
relatively wide sizes 1522, 1622, 2030, 2538
and 3038, which incorporate two needle roller
and cage assemblies and have a lubrication
hole in the outer ring.
Product highlights
Suitable for limited radial space
Low sectional height makes needle
roller bearings suitable for applications
when heavy radial loads and a limited
radial space exist. Depending on the
application, they may be used with or
without an inner ring, with a roller cage
assembly running directly on the shaft.
Drawn cup series the

popular choice
The popular drawn cup series have an
extremely thin-walled outer ring and
are intended to operate directly on the
shaft without use of an inner ring.

A wide variety of designs include
combined bearings for radial and
axial loads allowing for compact and
economical bearing arrangements.
Size range includes 3 to 360 mm
inside diameter.
Seals integration
SKF needle roller bearings are also
available with seals on one or two sides
making external seals unnecessary. The
seals are made of synthetic rubber and
provide efficient protection to the bearings against contaminants.
Figure 1
Open ends
Closed ends
187

Introduction
Sealed bearings
Variations
Sealed drawn cup needle roller bearings
For applications where an adequate seal is
not available or cannot be provided for space
reasons, sealed drawn cup needle roller bearings with open and closed ends (c,d,e) can be
supplied. These incorporate rubbing seals of
synthetic rubber and are filled with a lithium
base grease having good rust inhibiting
properties. The bearings are suitable for operating temperatures in the range 4 to +212 F
(-20 to +100 C). For further information on
sealed drawn cup needle roller bearings, please
consult SKF Applications Engineering.
The basic design of SKF needle roller
bearings in the size range up to and including
19 mm outside diameter has an outer ring
with either integral or inserted flanges (Figure 2a).
The larger bearings have integral flanges and
an annular groove and lubrication hole in the
outer ring (Figure 2b). Needle roller bearings
with flanged outer rings are mainly produced
as single row bearings. The exceptions are
bearings of series RNA 69 and NA 69 having
outside diameters of 55 mm and above
where two needle roller and cage assemblies
are guided between integral flanges on the
outer ring (Figure 2c). The outer ring, needle
rollers and cage of all bearings form a
non-separable unit.
Special solutions using

needle roller bearings
Single row needle roller bearings of series

RNA 49 and NA 49 are also available with
rubbing seals at one side, RS design (Figure 2d),
or at both sides, 2RS design (Figure 2e). The
seals are made of synthetic rubber and provide
efficient protection to the bearings against
contaminants. All bearings are supplied as standard filled with a lithium base grease having
good rust inhibiting properties. The bearings
are suitable for operating temperatures in the
range of -4 to +212 F (-20 to +100 C).
The inner rings of the sealed bearings are
1 mm wider than the outer rings. This will
allow the seals to provide adequate protection
against contaminants even where the shaft is
slightly displaced axially relative to the housing.
The inner rings also have a lubrication hole
so that, depending on the arrangement, it is
possible to relubricate the bearings via the
outer or inner rings.
SKF supplies many different types of needle

roller bearings in addition to those shown in
this catalog, including:
Needle roller and cage assemblies
Needle roller bearings without flanges
Alignment needle roller bearings
Combined needle roller / ball bearings
Combined needle roller / thrust
ball bearings
Combined needle roller / cylindrical roller
thrust bearings
Details on these special solution products are
available in other SKF publications, which can
be supplied upon request.
Figure 2
With inner rings
Without inner rings
188
Introduction
Internal Clearance
Minimum Load
Frequency Vibration Data

all ball and roller bearings, they must always
be subjected to a given minimum load.
This is also true of needle roller bearings,
particularly if they run at high speeds where
the inertia forces of the rollers and cage, and
the friction in the lubricant can have a detrimental influence on the rolling conditions in
the bearing. It may also cause damaging sliding
the raceways.
or similar means.

SKF needle roller bearings with inner ring are

supplied with Normal radial internal clearance
as standard. Bearings with greater or smaller
clearance may be available but this should be
checked before ordering.
The clearance values correspond to ISO 5753:
1991 and are shown in Table 1.
Loads
Needle roller bearings and standard needle
roller bearing assemblies can only accommodate
radial loads. Therefore
P = Fr
Table 1
Radial internal clearance of needle roller bearings
Bore
diameter
d
over
incl.
mm
in
C2
min max min
m
in
24
30
24
30
40
0
0.9449
1.1811
0.9449
1.1811
1.5748
0
0
5
25
25
30
40
50
65
50
65
80
1.5748
1.9685
2.5591
1.9685
2.5591
3.1496
5
10
10
80
100
120
100
120
140
3.1496
3.9370
4.7244
3.9370
4.7244
5.5118
140
160
180
160
180
200
5.5118
6.2992
7.0866
200
225
250
225
250
280
280
315
355
315
355
400
Normal
min max
m
min
in
max
C3
min max
m
min
in
0.0000 0.0010
0.0000 0.0010
0.0002 0.0012
20
20
25
45
45
50
0.0008
0.0008
0.0010
0.0018
0.0018
0.0020
35
35
45
60
60
70
35
40
45
0.0002 0.0014
0.0004 0.0016
0.0004 0.0018
30
40
40
60
70
75
0.0012
0.0016
0.0016
0.0024
0.0028
0.0030
50
60
65
15
15
15
50
55
60
0.0006 0.0020
0.0006 0.0022
0.0006 0.0024
50
50
60
85
90
105
0.0020
0.0020
0.0024
6.2992
7.0866
7.8740
20
25
35
70
75
90
0.0008 0.0028
0.0010 0.0030
0.0014 0.0035
70
75
90
120
125
145
7.8740
8.8583
9.8425
8.8583
9.8425
11.0236
45
45
55
105
110
125
0.0018 0.0041
0.0018 0.0043
0.0022 0.0049
11.0236
12.4016
13.9764
12.4016
13.9764
15.7480
55 130
65 145
100 190
0.0022 0.0051
0.0026 0.0057
0.0039 0.0075
max
C4
min
m
max
min
in
0.0014 0.0024
0.0014 0.0024
0.0018 0.0028
50
50
60
75
75
85
0.0020 0.0030
0.0020 0.0030
0.0024 0.0033
80
90
100
0.0020 0.0031
0.0024 0.0035
0.0026 0.0039
70
80
90
100
110
125
0.0028 0.0039
0.0031 0.0043
0.0035 0.0049
0.0033
0.0035
0.0041
75 110
85 125
100 145
0.0030 0.0043
0.0033 0.0049
0.0039 0.0057
105
125
145
140
165
190
0.0041 0.0055
0.0049 0.0065
0.0057 0.0075
0.0028
0.0030
0.0035
0.0047
0.0049
0.0057
115 165
120 170
140 195
0.0045 0.0065
0.0047 0.0067
0.0055 0.0077
165
170
195
215
220
250
0.0065 0.0085
0.0067 0.0087
0.0077 0.0098
105 165
110 175
125 195
0.0041
0.0043
0.0049
0.0065
0.0069
0.0077
160 220
170 235
190 260
0.0063 0.0087
0.0067 0.0093
0.0075 0.0102
220
235
260
280
300
330
0.0087 0.0110
0.0093 0.0118
0.0102 0.0130
130 205
145 225
190 280
0.0051
0.0057
0.0075
0.0081
0.0089
0.0110
200 275
225 305
280 370
0.0079 0.0108
0.0089 0.0120
0.0110 0.0146
275
305
370
350
385
460
0.0108 0.0138
0.0120 0.0152
0.0146 0.0181
max
max
189

Single row
Drawn cup and open end
Series: HK 0306 TN HK 2030
Size: 3 mm 20 mm
0.1181 in 0.7874 in
Series HK
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
N
lbf
Static
C0
N
lbf
Reference Limiting
speed
speed
r/min
r/min
Open end
g
oz
Closed end
g
oz
HK 0306 TN
HK 0408 TN
HK 0509
3
4
5
0.1181
0.1575
0.1969
7
8
9
0.2559
0.3150
0.3543
6
8
9
0.2362
0.3150
0.3543
1 230
1 720
2 380
277
387
535
880
1 320
2 080
198
297
468
30 000
26 000
22 000
43 000
38 000
34 000
1.00
1.60
2.00
0.04
0.06
0.07
1.00
1.80
2.10
0.04
0.06
0.07
HK 0608
HK 0609
HK 0709
6
6
7
0.2362
0.2362
0.2756
10
10
11
0.3937
0.3937
0.4331
8
9
9
0.3150
0.3543
0.3543
2 010
2 810
3 030
452
632
681
1 730
2 700
3 050
389
607
686
20 000
20 000
18 000
32 000
32 000
28 000
2.10
2.50
2.60
0.07
0.09
0.09
2.60
2.90
0.09
0.10
HK 0808
HK 0810
HK 0908
8
8
9
0.3150
0.3150
0.3543
12
12
13
0.4724
0.4724
0.5118
8
10
8
0.3150
0.3937
0.3150
2 700
3 690
3 800
607
830
854
2 750
4 050
4 300
618
910
967
17 000
17 000
16 000
26 000
26 000
24 000
2.70
3.00
3.00
0.10
0.11
0.11
3.00
3.40
-
0.11
0.11
-
HK 0910
HK 0912
HK 1010
9
9
10
0.3543
0.3543
0.3937
13
13
14
0.5118
0.5118
0.5512
10
12
10
0.3937
0.4724
0.3937
4 130
5 120
4 290
928
1 150
964
4 800
6 400
5 300
1 080
1 440
1 190
16 000
16 000
16 000
24 000
24 000
24 000
4.00
4.60
4.10
0.14
0.16
0.14
4.30
4.90
4.30
0.15
0.17
0.15
HK 1012
HK 1015
HK 1210
10
10
12
0.3937
0.3937
0.4724
14
14
16
0.5512
0.5512
0.6299
12
15
10
0.4724
0.5906
0.3937
5 390
6 600
4 840
1 210
1 480
1 090
6 950
9 000
6 400
1 560
2 020
1 440
16 000
16 000
14 000
24 000
24 000
20 000
4.80
6.00
4.60
0.17
0.21
0.16
5.00
6.20
5.20
0.18
0.22
0.18
HK 1212
HK 1312
HK 1412
12
13
14
0.4724
0.5118
0.5512
18
19
20
0.7087
0.7480
0.7874
12
12
12
0.4724
0.4724
0.4724
6 270
6 600
6 820
1 410
1 480
1 530
7 350
8 000
8 650
1 650
1 800
1 950
14 000
13 000
12 000
20 000
19 000
18 000
9.10
9.50
10.50
0.32
0.33
0.37
10.50
11.00
12.00
0.37
0.39
0.42
HK 1512
HK 1516
HK 15221)
15
15
15
0.5906
0.5906
0.5906
21
21
21
0.8268
0.8268
0.8268
12
16
22
0.4724
0.6299
0.8661
7 650
10 100
13 000
1 720
2 270
2 920
9 500
14 600
20 000
2 140
3 280
4 500
11 000
11 000
11 000
17 000
17 000
17 000
11.00
15.00
20.00
0.39
0.53
0.70
13.00
17.00
22.00
0.46
0.60
0.77
HK 1612
HK 1616
HK 16221)
16
16
16
0.6299
0.6299
0.6299
22
22
22
0.8661
0.8661
0.8661
12
16
22
0.4724
0.6299
0.8661
7 370
10 500
12 800
1 660
2 360
2 880
9 800
15 600
19 600
2 200
3 510
4 410
10 000
10 000
10 000
16 000
16 000
16 000
12.00
16.00
22.00
0.42
0.56
0.77
14.00
18.00
24.00
0.49
0.63
0.84
HK 1712
HK 1812
HK 1816
17
18
18
0.6693
0.7087
0.7087
23
24
24
0.9055
0.9449
0.9449
12
12
16
0.4724
0.4724
0.6299
7 650
7 920
11 200
1 720
1 780
2 520
10 600
11 200
17 600
2 380
2 520
3 960
10 000
9 500
9 500
16 000
15 000
15 000
12.00
13.00
18.00
0.42
0.46
0.63
15.00
15.00
20.00
0.53
0.53
0.70
HK 2010
HK 2012
HK 2016
20
20
20
0.7874
0.7874
0.7874
26
26
26
1.0236
1.0236
1.0236
10
12
16
0.3937
0.4724
0.6299
6 160
8 420
12 300
1 390
1 890
2 770
8 500
12 500
20 400
1 910
2 810
4 590
9 000
9 000
9 000
14 000
14 000
14 000
12.00
14.00
19.00
0.42
0.49
0.67
17.00
22.00
0.60
0.77
HK 2020
HK 20301)
20
20
0.7874
0.7874
26
26
1.0236
1.0236
20
30
0.7874
1.1811
15 100
20 900
3 400
4 700
26 500
40 500
5 960
9 110
9 000
9 000
14 000
14 000
24.00
35.00
0.84
1.20
27.00
38.00
0.95
1.30
1) Double row
190
Single row
Drawn cup and open end
Series: HK 2210 HK 6032
Size: 22 mm 60 mm
0.8661 in 2.3622 in
Series HK
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
N
lbf
Static
C0
N
lbf
Reference Limiting
speed
speed
r/min
r/min
Open end
g
oz
Closed end
g
oz
HK 2210
HK 2212
HK 2216
22
22
22
0.8661
0.8661
0.8661
28
28
28
1.1024
1.1024
1.1024
10
12
16
0.3937
0.4724
0.6299
7 210
8 800
13 000
1 620
1 980
2 920
10 600
13 700
22 400
2 380
3 080
5 040
8 000
8 000
8 000
12 000
12 000
12 000
12
15
21
0.42
0.53
0.74
18
24
0.63
0.84
HK 2220
HK 2512
HK 2516
22
25
25
0.8661
0.9843
0.9843
28
32
32
1.1024
1.2598
1.2598
20
12
16
0.7874
0.4724
0.6299
15 700
10 500
15 100
3 530
2 360
3 400
29 000
15 300
24 000
6 520
3 440
5 400
8 000
7 500
7 500
12 000
11 000
11 000
26
21
27
0.91
0.74
0.95
30
24
31
1.05
0.84
1.10
HK 2520
HK 2526
HK 25381)
25
25
25
0.9843
0.9843
0.9843
32
32
32
1.2598
1.2598
1.2598
20
26
38
0.7874
1.0236
1.4961
19 000
24 200
33 000
4 270
5 440
7 420
32 500
45 000
65 500
7 310
10 100
14 700
7 500
7 500
7 500
11 000
11 000
11 000
34
45
65
1.20
1.55
2.25
39
49
69
1.35
1.70
2.40
HK 2816
HK 2820
HK 3012
28
28
30
1.1024
1.1024
1.1811
35
35
37
1.3780
1.3780
1.4567
16
20
12
0.6299
0.7874
0.4724
15 700
20 100
11 700
3 530
4 520
2 630
26 500
36 500
18 300
5 960
8 210
4 110
6 700
6 700
6 300
9 500
9 500
9 000
30
38
24
1.05
1.30
0.84
34
43
28
1.20
1.50
0.98
HK 3016
HK 3020
HK 3026
30
30
30
1.1811
1.1811
1.1811
37
37
37
1.4567
1.4567
1.4567
16
20
26
0.6299
0.7874
1.0236
16 500
20 900
27 000
3 710
4 700
6 070
29 000
40 000
54 000
6 520
8 990
12 100
6 300
6 300
6 300
9 000
9 000
9 000
32
40
53
1.10
1.40
1.85
37
47
59
1.30
1.65
2.05
HK 30381)
HK 3512
HK 3516
30
35
35
1.1811
1.3780
1.3780
37
42
42
1.4567
1.6535
1.6535
38
12
16
1.4961
0.4724
0.6299
35 800
12 500
17 900
8 050
2 810
4 020
80 000
21 600
34 000
18 000
4 860
7 640
6 300
5 600
5 600
9 000
8 000
8 000
76
28
37
2.65
0.98
1.30
83
33
44
2.90
1.15
1.55
HK 3520
HK 4012
HK 4016
35
40
40
1.3780
1.5748
1.5748
42
47
47
1.6535
1.8504
1.8504
20
12
16
0.7874
0.4724
0.6299
22 900
13 400
19 000
5 150
3 010
4 270
46 500
24 500
39 000
10 500
5 510
8 770
5 600
5 000
5 000
8 000
7 000
7 000
46
31
42
1.60
1.10
1.45
55
38
51
1.90
1.30
1.80
HK 4020
HK 4512
HK 4516
40
45
45
1.5748
1.7717
1.7717
47
52
52
1.8504
2.0472
2.0472
20
12
16
0.7874
0.4724
0.6299
24 200
14 200
20 500
5 440
3 190
4 610
53 000
27 500
43 000
11 900
6 180
9 670
5 000
4 500
4 500
7 000
6 300
6 300
52
35
46
1.80
1.20
1.60
62
56
2.15
1.95
HK 4520
HK 5020
HK 5025
45
50
50
1.7717
1.9685
1.9685
52
58
58
2.0472
2.2835
2.2835
20
20
25
0.7874
0.7874
0.9843
26 000
29 200
36 900
5 850
6 560
8 300
60 000
63 000
85 000
13 500
14 200
19 100
4 500
4 000
4 000
6 300
5 600
5 600
58
72
90
2.00
2.50
3.15
71
87
109
2.50
3.05
3.80
HK 5520
HK 5528
HK 6012
55
55
60
2.1654
2.1654
2.3622
63
63
68
2.4803
2.4803
2.6772
20
28
12
0.7874
1.1024
0.4724
30 300
41 800
17 600
6 810 67 000
9 400 104 000
3 960 32 000
15 100
23 400
7 190
3 600
3 600
3 400
5 000
5 000
4 800
78
110
49
2.70
3.85
1.70
94
130
77
3.30
4.55
2.70
HK 6020
HK 6032
60
60
2.3622
2.3622
68
68
2.6772
2.6772
20
32
0.7874
1.2598
31 900
51 200
7 170 75 000
11 500 137 000
16 900
30 800
3 400
3 400
4 800
4 800
85
135
2.95
4.70
105
165
3.65
5.75
1) Double row
191

Single row
with inner ring
Series: NA 4822 NA 4876
Size: 110 mm 380 mm
4.3307 in 14.9606 in
Series NA
NA 4948
Series
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
B
mm
in
mm
in
NA 4822
NA 4824
NA 4826
110
120
130
4.3307
4.7244
5.1181
140
150
165
5.5118
5.9055
6.4961
30
30
35
NA 4828
NA 4830
NA 4832
140
150
160
5.5118
5.9055
6.2992
175
190
200
6.8898
7.4803
7.8740
NA 4834
NA 4836
NA 4838
170
180
190
6.6929
7.0866
7.4803
215
225
240
NA 4840
NA 4844
NA 4848
200
220
240
7.8740
8.6614
9.4488
NA 4852
NA 4856
NA 4860
260
280
300
NA 4864
NA 4868
NA 4872
NA 4876
Dynamic
C
Speed rating
Static
C0
Mass
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
lbf
1.1811
1.1811
1.3780
93 500
99 000
119 000
21 100
22 300
26 800
232 000
255 000
325 000
52 200
57 400
73 100
3 400
3 200
2 800
3 800
3 600
3 200
1.10
1.15
1.80
2.40
2.50
4.00
35
40
40
1.3780
1.5748
1.5748
121 000
147 000
157 000
27 300
33 100
35 300
345 000
415 000
450 000
77 600
93 300
52 200
2 600
2 400
2 200
3 000
2 800
2 600
1.90
2.70
2.90
4.20
6.00
6.40
8.4646
8.8583
9.4488
45
45
50
1.7717
1.7717
1.9685
179 000
190 000
220 000
40 300
42 800
49 500
520 000
570 000
710 000
116 900
128 200
159 700
2 200
2 000
1 900
2 400
2 400
2 200
3.95
4.20
5.60
8.70
9.30
12.30
250
270
300
9.8425
10.6299
11.8110
50
50
60
1.9685
1.9685
2.3622
224 000
238 000
347 000
50 400
53 600
78 100
735 000
815 000
1 120 000
165 300
183 300
251 800
1 800
1 700
1 500
2 000
1 900
1 700
5.85
6.40
10.00
12.90
14.10
22.00
10.2362
11.0236
11.8110
320
350
380
12.5984
13.7795
14.9606
60
69
80
2.3622
2.7165
3.1496
358 000
429 000
594 000
80 500
96 500
133 600
1 200 000
1 320 000
1 800 000
269 800
296 800
404 700
1 400
1 300
1 100
1 500
1 400
1 300
10.50
15.50
22.00
23.10
34.20
48.50
320
340
360
12.5984
13.3858
14.1732
400
420
440
15.7480
16.5354
17.3228
80
80
80
3.1496
3.1496
3.1496
605 000
616 000
627 000
136 100
138 500
141 000
1 900 000
1 960 000
2 040 000
427 200
440 700
458 600
1 100
1 000
950
1 200
1 200
1 100
23.00
24.00
25.50
50.70
52.90
56.20
380
14.9606
480
18.8976
100
3.9370
968 000
217 700
3 000 000
674 400
900
1 000
42.50
93.70
192
Single row
with inner ring
Open and sealed
Size: 10 mm 75 mm
0.3937 in 2.9528 in
Series NA
NA 4949
Series
Designation
Series NA 2RS
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
lbf
lbf
8 800
7 370
9 900
2 000
1 700
2 300
10 400
8 150
12 200
2 400
1 900
2 800
24 000
22 000
28 000
12 000
26 000
0.02
0.03
0.03
0.05
0.06
0.06
0.5118
0.5118
0.5118
8 090
11 200
9 130
1 900
2 600
2 100
9 650
15 300
12 000
2 200
3 500
2 700
19 000
11 000
22 000
9 500
0.03
0.03
0.04
0.06
0.07
0.08
13
13
17
0.5118
0.5118
0.6693
11 400
9 520
21 600
2 600
2 200
4 900
16 300
12 900
28 000
3 700
2 900
6 300
18 000
15 000
20 000
9 000
17 000
0.04
0.04
0.08
0.08
0.09
0.20
1.4567
1.5354
1.6535
17
17
17
0.6693
0.6693
0.6693
19 400
23 300
24 200
4 400
5 300
5 500
22 400
32 000
34 500
5 100
7 200
7 800
14 000
13 000
7 500
15 000
15 000
0.08
0.08
0.09
0.20
0.20
0.20
42
45
47
1.6535
1.7717
1.8504
17
17
17
0.6693
0.6693
0.6693
21 600
25 100
25 500
4 900
5 700
5 800
27 500
36 500
39 000
6 200
8 300
8 800
12 000
11 000
6 300
14 000
13 000
0.09
0.10
0.10
0.20
0.20
0.20
1.1811
1.2598
1.3780
47
52
55
1.8504
2.0472
2.1654
17
20
20
0.6693
0.7874
0.7874
23 300
30 800
31 900
5 300
7 000
7 200
32 000
51 000
54 000
7 200
11 500
12 200
10 000
9 500
5 600
11 000
11 000
0.10
0.16
0.17
0.20
0.40
0.40
35
40
40
1.3780
1.5748
1.5748
55
62
62
2.1654
2.4409
2.4409
20
22
22
0.7874
0.8661
0.8661
27 000
42 900
36 900
6 100
9 700
8 300
43 000
71 000
58 500
9 700
16 000
13 200
8 000
5 400
9 500
4 000
0.18
0.23
0.25
0.40
0.50
0.60
NA 4909
NA 4909 2RS
NA 4910
45
45
50
1.7717
1.7717
1.9685
68
68
72
2.6772
2.6772
2.8346
22
22
22
0.8661
0.8661
0.8661
45 700
39 100
47 300
10 300
8 800
10 700
78 000
64 000
85 000
17 600
14 400
19 200
7 500
7 000
8 500
3 800
8 000
0.27
0.29
0.27
0.60
0.60
0.60
NA 4910 2RS
NA 4911
NA 4912
50
55
60
1.9685
2.1654
2.3622
72
80
85
2.8346
3.1496
3.3465
22
25
25
0.8661
0.9843
0.9843
40 200
57 200
60 500
9 100
12 900
13 700
69 500
106 000
114 000
15 700
23 900
25 700
6 300
6 000
3 400
7 000
6 700
0.30
0.39
0.43
0.70
0.90
0.95
NA 4913
NA 4914
NA 4915
65
70
75
2.5591
2.7559
2.9528
90
100
105
3.5433
3.9370
4.1339
25
30
30
0.9843
1.1811
1.1811
61 600
84 200
84 200
13 900
19 000
19 000
120 000
163 000
170 000
27 000
36 700
38 300
5 600
5 000
4 800
6 300
5 600
5 300
0.46
0.73
0.78
1.00
1.60
1.70
in
NA 4900
NA 4900 2RS
NA 4901
10
10
12
0.3937
0.3937
0.4724
22
22
24
0.8661
0.8661
0.9449
13
13
13
0.5118
0.5118
0.5118
NA 4901 2RS
NA 4902
NA 4902 2RS
12
15
15
0.4724
0.5906
0.5906
24
28
28
0.9449
1.1024
1.1024
13
13
13
NA 4903
NA 4903 2RS
NA 4904
17
17
20
0.6693
0.6693
0.7874
30
30
37
1.1811
1.1811
1.4567
NA 4904 2RS
NA 49/22
NA 4905
20
22
25
0.7874
0.8661
0.9843
37
39
42
NA 4905 2RS
NA 49/28
NA 4906
25
28
30
0.9843
1.1024
1.1811
NA 4906 2RS
NA 49/32
NA 4907
30
32
35
NA 4907 2RS
NA 4908
NA 4908 2RS
Static
C0
Mass
Reference
speed
r/min
mm
Dynamic
C
Speed rating
Limiting
speed
r/min
kg
lb
193

Single row
with inner ring
Open and sealed
Size: 80 mm 140 mm
3.1496 in 5.5118 in
Series
SeriesNA
NA49.2RS
2RS
Series
Series NA
NA 4949
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
mm
in
NA 4916
NA 4917
NA 4918
80
85
90
3.1496
3.3465
3.5433
110
120
125
4.3307
4.7244
4.9213
30
35
35
NA 4919
NA 4920
NA 4922
95
100
110
3.7402
3.9370
4.3307
130
140
150
5.1181
5.5118
5.9055
NA 4924
NA 4926
NA 4928
120
130
140
4.7244
5.1181
5.5118
165
180
190
6.4961
7.0866
7.4803
Dynamic
C
Speed rating
Static
C0
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
lbf
1.1811
1.3780
1.3780
88 000
108 000
112 000
19 800
24 300
25 200
183 000
250 000
265 000
41 200
56 200
59 600
4 500
4 000
3 800
5 000
4 500
4 300
0.88
1.25
1.30
1.90
2.80
2.90
35
40
40
1.3780
1.5748
1.5748
114 000
125 000
130 000
25 700
28 100
29 300
270 000
280 000
300 000
60 700
63 000
67 500
3 600
3 400
3 200
4 000
4 000
3 600
1.35
1.90
2.05
3.00
4.20
4.50
45
50
50
1.7717
1.9685
1.9685
176 000
198 000
205 000
39 600
44 600
46 100
405 000
480 000
510 000
91 100
108 000
114 700
3 000
2 600
2 400
3 400
3 000
2 800
2.85
3.90
4.15
6.30
8.60
9.10
194
Mass
Double row
with inner ring
Size: 12 mm 95 mm
0.4724 in 3.7402 in
Series NANA
69 69
Series
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
mm
in
NA 6901
NA 6902
NA 6903
12
15
17
0.4724
0.5906
0.6693
24
28
30
0.9449
1.1024
1.1811
22
23
23
NA 6904
NA 69/22
NA 6905
20
22
25
0.7874
0.8661
0.9843
37
39
42
1.4567
1.5354
1.6535
NA 69/28
NA 6906
NA 69/32
28
30
32
1.1024
1.1811
1.2598
45
47
52
NA 6907
NA 6908
NA 6909
35
40
45
1.3780
1.5748
1.7717
NA 6910
NA 6911
NA 6912
50
55
60
NA 6913
NA 6914
NA 6915
Dynamic
C
Speed rating
Static
C0
lbf
Mass
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
lbf
0.8661
0.9055
0.9055
16 100
17 200
18 700
3 700
3 900
4 300
23 200
27 000
30 500
5 300
6 100
6 900
22 000
19 000
18 000
26 000
22 000
20 000
0.05
0.06
0.07
0.10
0.10
0.20
30
30
30
1.1811
1.1811
1.1811
35 200
36 900
38 000
8 000
8 300
8 600
53 000
57 000
62 000
12 000
12 900
14 000
15 000
14 000
13 000
17 000
15 000
15 000
0.14
0.15
0.16
0.30
0.30
0.40
1.7717
1.8504
2.0472
30
30
36
1.1811
1.1811
1.4173
39 600
42 900
47 300
9 000
9 700
10 700
65 500
75 000
90 000
14 800
16 900
20 300
12 000
11 000
10 000
14 000
13 000
11 000
0.18
0.19
0.29
0.40
0.40
0.60
55
62
68
2.1654
2.4409
2.6772
36
40
40
1.4173
1.5748
1.5748
48 400
67 100
70 400
10 900
15 100
15 900
93 000
125 000
137 000
21 000
28 100
30 800
9 500
8 000
7 500
11 000
9 500
8 500
0.31
0.43
0.50
0.70
0.95
1.10
1.9685
2.1654
2.3622
72
80
85
2.8346
3.1496
3.3465
40
45
45
1.5748
1.7717
1.7717
73 700
89 700
93 500
16 600
20 200
21 100
150 000
190 000
204 000
33 800
42 800
45 900
7 000
6 300
6 000
8 000
7 000
6 700
0.52
0.78
0.81
1.10
1.80
1.80
65
70
75
2.5591
2.7559
2.9528
90
100
105
3.5433
3.9370
4.1339
45
54
54
1.7717
2.1260
2.1260
95 200
128 000
130 000
21 500
28 800
29 300
212 000
285 000
290 000
47 700
64 100
65 200
5 600
5 000
4 800
6 300
5 600
5 300
0.83
1.35
1.45
1.80
3.00
3.20
NA 6916
NA 6917
NA 6918
80
85
90
3.1496
3.3465
3.5433
110
120
125
4.3307
4.7244
4.9213
54
63
63
2.1260
2.4803
2.4803
134 000
165 000
172 000
30 200
37 100
38 700
315 000
425 000
450 000
70 900
95 600
101 200
4 500
4 000
3 800
5 000
4 500
4 300
1.50
2.20
2.30
3.30
4.90
5.10
NA 6919
95
3.7402
130
5.1181
63
2.4803
172 000
38 700
465 000
104 600
3 600
4 000
2.50
5.50
195

Single row
without inner ring
Series: NK 5/12 TN NK 22/16
Size: 5 mm 22 mm
0.1969 in 0.8661 in
Series NK
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
N
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
NK 5/12 TN
NK 6/10 TN
NK 6/12 TN
5
6
6
0.1969
0.2362
0.2362
10
12
12
0.3937
0.4724
0.4724
10
10
12
0.3937
0.3937
0.4724
2 920
2 550
3 300
700
600
800
2 700
2 360
3 200
700
600
800
36 000
34 000
34 000
40 000
38 000
38 000
0.01
0.01
0.01
0.01
0.01
0.01
NK 7/10 TN
NK 7/12 TN
NK 8/12 TN
7
7
8
0.2756
0.2756
0.3150
14
14
15
0.5512
0.5512
0.5906
10
12
12
0.3937
0.4724
0.4724
2 810
3 580
3 800
700
900
900
2 750
3 750
4 250
700
900
1 000
32 000
32 000
32 000
36 000
36 000
36 000
0.01
0.01
0.01
0.02
0.02
0.02
NK 8/16 TN
NK 9/12 TN
NK 9/16 TN
8
9
9
0.3150
0.3543
0.3543
15
16
16
0.5906
0.6299
0.6299
16
12
16
0.6299
0.4724
0.6299
5 010
4 400
5 720
1 200
1 000
1 300
5 850
5 200
7 200
1 400
1 200
1 700
32 000
30 000
30 000
36 000
34 000
34 000
0.01
0.01
0.01
0.03
0.02
0.03
NK 10/12 TN
NK 10/16 TN
NK 12/12
10
10
12
0.3937
0.3937
0.4724
17
17
19
0.6693
0.6693
0.7480
12
16
12
0.4724
0.6299
0.4724
4 400
5 940
6 710
1 000
1 400
1 600
5 400
8 000
8 150
1 300
1 800
1 900
28 000
28 000
26 000
32 000
32 000
30 000
0.01
0.01
0.01
0.02
0.03
0.03
NK 12/16
NK 14/16
NK 14/20
12
14
14
0.4724
0.5512
0.5512
19
22
22
0.7480
0.8661
0.8661
16
16
20
0.6299
0.6299
0.7874
9 130
10 200
12 800
2 100
2 300
2 900
12 000
12 500
16 600
2 700
2 900
3 800
26 000
24 000
24 000
30 000
28 000
28 000
0.02
0.02
0.03
0.04
0.05
0.06
NK 15/16
NK 15/20
NK 16/16
15
15
16
0.5906
0.5906
0.6299
23
23
24
0.9055
0.9055
0.9449
16
20
16
0.6299
0.7874
0.6299
11 000
13 800
11 700
2 500
3 200
2 700
14 000
18 300
15 300
3 200
4 200
3 500
24 000
24 000
22 000
26 000
26 000
26 000
0.02
0.03
0.02
0.05
0.06
0.05
NK 16/20
NK 17/16
NK 17/20
16
17
17
0.6299
0.6693
0.6693
24
25
25
0.9449
0.9843
0.9843
20
16
20
0.7874
0.6299
0.7874
14 500
12 100
15 100
3 300
2 800
3 400
20 000
16 600
22 000
4 500
3 800
5 000
22 000
22 000
22 000
26 000
26 000
26 000
0.03
0.02
0.03
0.06
0.05
0.07
NK 18/16
NK 18/20
NK 19/16
18
18
19
0.7087
0.7087
0.7480
26
26
27
1.0236
1.0236
1.0630
16
20
16
0.6299
0.7874
0.6299
12 800
16 100
13 400
2 900
3 700
3 100
17 600
23 600
19 000
4 000
5 400
4 300
22 000
22 000
20 000
24 000
24 000
24 000
0.03
0.03
0.03
0.06
0.07
0.06
NK 19/20
NK 20/16
NK 20/20
19
20
20
0.7480
0.7874
0.7874
27
28
28
1.0630
1.1024
1.1024
20
16
20
0.7874
0.6299
0.7874
16 500
13 200
16 500
3 800
3 000
3 800
25 500
19 300
25 500
5 800
4 400
5 800
20 000
19 000
19 000
24 000
22 000
22 000
0.03
0.03
0.03
0.07
0.06
0.07
NK 21/16
NK 21/20
NK 22/16
21
21
22
0.8268
0.8268
0.8661
29
29
30
1.1417
1.1417
1.1811
16
20
16
0.6299
0.7874
0.6299
13 800
17 200
14 200
3 200
3 900
3 200
20 400
27 000
21 600
4 600
6 100
4 900
19 000
19 000
18 000
22 000
22 000
20 000
0.03
0.04
0.03
0.06
0.08
0.07
196
Single row
without inner ring
Series: NK 22/20 NK 47/20
Size: 22 mm 47 mm
0.8661 in 1.8504 in
Series NK
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
NK 22/20
NK 24/16
NK 24/20
22
24
24
0.8661
0.9449
0.9449
30
32
32
1.1811
1.2598
1.2598
20
16
20
0.7874
0.6299
0.7874
17 900
15 400
19 000
4 100
3 500
4 300
29 000
24 500
32 500
6 600
5 600
7 400
18 000
16 000
16 000
20 000
19 000
19 000
0.04
0.03
0.04
0.08
0.07
0.09
NK 25/16
NK 25/20
NK 26/16
25
25
26
0.9843
0.9843
1.0236
33
33
34
1.2992
1.2992
1.3386
16
20
16
0.6299
0.7874
0.6299
15 100
19 000
15 700
3 400
4 300
3 600
24 500
32 500
26 000
5 600
7 400
5 900
16 000
16 000
15 000
18 000
18 000
17 000
0.03
0.04
0.03
0.07
0.09
0.07
NK 26/20
NK 28/20
NK 28/30
26
28
28
1.0236
1.1024
1.1024
34
37
37
1.3386
1.4567
1.4567
20
20
30
0.7874
0.7874
1.1811
19 400
22 000
31 900
4 400
5 000
7 200
34 500
36 500
60 000
7 800
8 300
13 500
15 000
14 000
14 000
17 000
16 000
16 000
0.04
0.05
0.08
0.09
0.10
0.20
NK 29/20
NK 29/30
NK 30/20
29
29
30
1.1417
1.1417
1.1811
38
38
40
1.4961
1.4961
1.5748
20
30
20
0.7874
1.1811
0.7874
22 000
31 900
22 900
5 000
7 200
5 200
36 500
60 000
38 000
8 300
13 500
8 600
14 000
14 000
13 000
15 000
15 000
15 000
0.05
0.08
0.07
0.10
0.20
0.10
NK 30/30
NK 32/20
NK 32/30
30
32
32
1.1811
1.2598
1.2598
40
42
42
1.5748
1.6535
1.6535
30
20
30
1.1811
0.7874
1.1811
33 000
23 300
34 100
7 500
5 300
7 700
63 000
40 500
65 500
14 200
9 200
14 800
13 000
12 000
12 000
15 000
14 000
14 000
0.10
0.07
0.10
0.20
0.10
0.20
NK 35/20
NK 35/30
NK 37/20
35
35
37
1.3780
1.3780
1.4567
45
45
47
1.7717
1.7717
1.8504
20
30
20
0.7874
1.1811
0.7874
24 600
35 800
25 100
5 600
8 100
5 700
45 000
72 000
46 500
10 200
16 200
10 500
11 000
11 000
11 000
13 000
13 000
12 000
0.07
0.11
0.08
0.20
0.20
0.20
NK 37/30
NK 38/20
NK 38/30
37
38
38
1.4567
1.4961
1.4961
47
48
48
1.8504
1.8898
1.8898
30
20
30
1.1811
0.7874
1.1811
36 900
25 500
37 400
8 300
5 800
8 500
76 500
49 000
80 000
17 200
11 100
18 000
11 000
11 000
11 000
12 000
12 000
12 000
0.11
0.08
0.12
0.20
0.20
0.30
NK 40/20
NK 40/30
NK 42/20
40
40
42
1.5748
1.5748
1.6535
50
50
52
1.9685
1.9685
2.0472
20
30
20
0.7874
1.1811
0.7874
26 400
38 000
27 000
6 000
8 600
6 100
51 000
83 000
53 000
11 500
18 700
12 000
10 000
10 000
9 500
11 000
11 000
11 000
0.08
0.13
0.09
0.20
0.30
0.20
NK 42/30
NK 43/20
NK 43/30
42
43
43
1.6535
1.6929
1.6929
52
53
53
2.0472
2.0866
2.0866
30
20
30
1.1811
0.7874
1.1811
39 100
27 500
40 200
8 800
6 200
9 100
86 500
55 000
90 000
19 500
12 400
20 300
9 500
9 500
9 500
11 000
11 000
11 000
0.13
0.09
0.13
0.30
0.20
0.30
NK 45/20
NK 45/30
NK 47/20
43
43
47
1.6929
1.6929
1.8504
55
55
57
2.1654
2.1654
2.2441
20
30
20
0.7874
1.1811
0.7874
27 500
40 200
29 200
6 200
9 100
6 600
57 000
93 000
61 000
12 900
21 000
13 800
9 000
9 000
8 500
10 000
10 000
10 000
0.09
0.14
0.10
0.20
0.30
0.20
197

Single row
without inner ring
Series: NK 47/30 NK 110/40
Size: 47 mm 110 mm
1.8504 in 4.3307 in
Series NK
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
NK 47/30
NK 50/25
NK 50/35
47
50
50
1.8504
1.9685
1.9685
57
62
62
2.2441
2.4409
2.4409
30
25
35
1.1811
0.9843
1.3780
41 800
38 000
49 500
9 400
8 600
11 200
98 000
78 000
110 000
22 100
17 600
24 800
8 500
8 000
8 000
10 000
9 000
9 000
0.14
0.16
0.22
0.30
0.40
0.50
NK 55/25
NK 55/35
NK 60/25
55
55
60
2.1654
2.1654
2.3622
68
68
72
2.6772
2.6772
2.8346
25
35
25
0.9843
1.3780
0.9843
40 200
52 300
41 800
9 100
11 800
9 400
88 000
122 000
96 500
19 800
27 500
21 700
7 500
7 500
6 700
8 500
8 500
7 500
0.18
0.25
0.19
0.40
0.60
0.40
NK 60/35
NK 65/25
NK 65/35
60
65
65
2.3622
2.5591
2.5591
72
78
78
2.8346
3.0709
3.0709
35
25
35
1.3780
0.9843
1.3780
55 000
44 000
58 300
12 400
9 900
13 200
134 000
104 000
146 000
30 200
23 400
32 900
6 700
6 300
6 300
7 500
7 000
7 000
0.26
0.22
0.31
0.60
0.50
0.70
NK 68/25
NK 68/35
NK 70/25
68
68
70
2.6772
2.6772
2.7559
82
82
85
3.2283
3.2283
3.3465
25
35
25
0.9843
1.3780
0.9843
44 000
60 500
44 600
9 900
13 700
10 100
95 000
146 000
98 000
21 400
32 900
22 100
6 000
6 000
6 000
6 700
6 700
6 700
0.24
0.34
0.26
0.50
0.70
0.60
NK 70/35
NK 73/25
NK 73/35
70
73
73
2.7559
2.8740
2.8740
85
90
90
3.3465
3.5433
3.5433
35
25
35
1.3780
0.9843
1.3780
61 600
52 800
73 700
13 900
11 900
16 600
150 000
106 000
163 000
33 800
23 900
36 700
6 000
5 600
5 600
6 700
6 300
6 300
0.37
0.30
0.43
0.80
0.70
0.90
NK 75/25
NK 75/35
NK 80/25
75
75
80
2.9528
2.9528
3.1496
92
92
95
3.6220
3.6220
3.7402
25
35
25
0.9843
1.3780
0.9843
53 900
74 800
56 100
12 200
16 900
12 700
110 000
170 000
127 000
24 800
38 300
28 600
5 300
5 300
5 000
6 000
6 000
5 600
0.32
0.45
0.30
0.70
1.00
0.70
NK 80/35
NK 85/25
NK 85/35
80
85
85
3.1496
3.3465
3.3465
95
105
105
3.7402
4.1339
4.1339
35
25
35
1.3780
0.9843
1.3780
76 500
69 300
96 800
17 200
15 600
21 800
190 000
132 000
200 000
42 800
29 700
45 000
5 000
4 800
4 800
5 600
5 300
5 300
0.43
0.43
0.60
0.90
0.90
1.30
NK 90/25
NK 90/35
NK 95/26
90
90
95
3.5433
3.5433
3.7402
110
110
115
4.3307
4.3307
4.5276
25
35
26
0.9843
1.3780
1.0236
72 100
101 000
73 700
16 300
22 800
16 600
140 000
216 000
146 000
31 500
48 600
32 900
4 500
4 500
4 300
5 000
5 000
4 800
0.45
0.63
0.49
1.00
1.40
1.10
NK 95/36
NK 100/26
NK 100/36
95
100
100
3.7402
3.9370
3.9370
115
120
120
4.5276
4.7244
4.7244
36
26
36
1.4173
1.0236
1.4173
105 000
76 500
108 000
23 700
17 200
24 300
232 000
156 000
250 000
52 200
35 100
56 200
4 300
4 000
4 000
4 800
4 500
4 500
0.68
0.52
0.72
1.50
1.10
1.60
NK 105/26
NK 105/36
NK 110/30
105
105
110
4.1339
4.1339
4.3307
125
125
130
4.9213
4.9213
5.1181
26
36
30
1.0236
1.4173
1.1811
78 100
112 000
96 800
17 600
25 200
21 800
166 000
265 000
220 000
37 400
59 600
49 500
3 800
3 800
3 600
4 300
4 300
4 000
0.54
0.71
0.65
1.20
1.60
1.40
NK 110/40
110
4.3307
130
5.1181
40
1.5748
123 000
27 700
305 000
68 600
3 600
4 000
0.83
1.80
198
Single row
with inner ring
Series: NKI 5/12 TN NKI 35/30
Size: 5 mm 35 mm
0.1969 in 1.3780 in
Series NKI
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
Dynamic
C
N
Speed rating
Static
C0
lbf
lbf
Reference
speed
r/min
Mass
Limiting
speed
r/min
kg
lb
NKI 5/12 TN
NKI 5/16 TN
NKI 6/12 TN
5
5
6
0.1969
0.1969
0.2362
15
15
16
0.5906
0.5906
0.6299
12
16
12
0.4724
0.6299
0.4724
3 800
5 010
4 400
900
1 200
1 000
4 250
5 850
5 200
1 000
1 400
1 200
32 000
32 000
30 000
36 000
36 000
34 000
0.01
0.02
0.01
0.03
0.03
0.03
NKI 6/16 TN
NKI 7/12 TN
NKI 7/16 TN
6
7
7
0.2362
0.2756
0.2756
16
17
17
0.6299
0.6693
0.6693
16
12
16
0.6299
0.4724
0.6299
5 720
4 570
5 940
1 300
1 100
1 400
7 200
5 700
8 000
1 700
1 300
1 800
30 000
28 000
28 000
34 000
32 000
32 000
0.02
0.01
0.02
0.04
0.03
0.04
NKI 9/12
NKI 9/16
NKI 10/16
9
9
10
0.3543
0.3543
0.3937
19
19
22
0.7480
0.7480
0.8661
12
16
16
0.4724
0.6299
0.6299
6 710
9 130
10 200
1 600
2 100
2 300
8 150
12 000
12 500
1 900
2 700
2 900
26 000
26 000
24 000
30 000
30 000
28 000
0.02
0.02
0.03
0.04
0.05
0.06
NKI 10/20
NKI 12/16
NKI 12/20
10
12
12
0.3937
0.4724
0.4724
22
24
24
0.8661
0.9449
0.9449
20
16
20
0.7874
0.6299
0.7874
12 800
11 700
14 500
2 900
2 700
3 300
16 600
15 300
20 000
3 800
3 500
4 500
24 000
22 000
22 000
28 000
26 000
26 000
0.04
0.03
0.04
0.08
0.07
0.09
NKI 15/16
NKI 15/20
NKI 17/16
15
15
17
0.5906
0.5906
0.6693
27
27
29
1.0630
1.0630
1.1417
16
20
16
0.6299
0.7874
0.6299
13 400
16 500
13 800
3 100
3 800
3 200
19 000
25 500
20 400
4 300
5 800
4 600
20 000
20 000
19 000
24 000
24 000
22 000
0.04
0.05
0.04
0.09
0.10
0.09
NKI 17/20
NKI 20/16
NKI 20/20
17
20
20
0.6693
0.7874
0.7874
29
32
32
1.1417
1.2598
1.2598
20
16
20
0.7874
0.6299
0.7874
17 200
15 400
19 000
3 900
3 500
4 300
27 000
24 500
32 500
6 100
5 600
7 400
19 000
16 000
16 000
22 000
19 000
19 000
0.05
0.05
0.06
0.10
0.10
0.10
NKI 22/16
NKI 22/20
NKI 25/20
22
22
25
0.8661
0.8661
0.9843
34
34
38
1.3386
1.3386
1.4961
16
20
20
0.6299
0.7874
0.7874
15 700
19 400
22 000
3 600
4 400
5 000
26 000
34 500
36 500
5 900
7 800
8 300
15 000
15 000
14 000
17 000
17 000
15 000
0.05
0.07
0.08
0.10
0.10
0.20
NKI 25/30
NKI 28/20
NKI 28/30
25
28
28
0.9843
1.1024
1.1024
38
42
42
1.4961
1.6535
1.6535
30
20
30
1.1811
0.7874
1.1811
31 900
23 300
34 100
7 200
5 300
7 700
60 000
40 500
65 500
13 500
9 200
14 800
14 000
12 000
12 000
15 000
14 000
14 000
0.12
0.10
0.15
0.30
0.20
0.30
NKI 30/20
NKI 30/30
NKI 32/20
30
30
32
1.1811
1.1811
1.2598
45
45
47
1.7717
1.7717
1.8504
20
30
20
0.7874
1.1811
0.7874
24 600
35 800
25 100
5 600
8 100
5 700
45 000
72 000
46 500
10 200
16 200
10 500
11 000
11 000
11 000
13 000
13 000
12 000
0.11
0.17
0.12
0.20
0.40
0.30
NKI 32/30
NKI 35/20
NKI 35/30
32
35
35
1.2598
1.3780
1.3780
47
50
50
1.8504
1.9685
1.9685
30
20
30
1.1811
0.7874
1.1811
36 900
26 400
38 000
8 300
6 000
8 600
76 500
51 000
83 000
17 200
11 500
18 700
11 000
10 000
10 000
12 000
11 000
11 000
0.18
0.13
0.19
0.40
0.30
0.40
199

Single row
with inner ring
Series: NKI 38/20 NKI 100/40
Size: 38 mm 100 mm
1.4961 in 3.9370 in
Series NKI
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
lbf
lbf
0.7874
1.1811
0.7874
27 500
40 200
27 500
6 200
9 100
6 200
55 000
90 000
57 000
12 400
20 300
12 900
9 500
9 500
9 000
11 000
11 000
10 000
0.14
0.21
0.14
0.30
0.50
0.30
30
20
30
1.1811
0.7874
1.1811
40 200
29 200
41 800
9 100
6 600
9 400
93 000
61 000
98 000
21 000
13 800
22 100
9 000
8 500
8 500
10 000
10 000
10 000
0.22
0.15
0.22
0.50
0.30
0.50
2.4409
2.4409
2.6772
25
35
25
0.9843
1.3780
0.9843
38 000
49 500
40 200
8 600
11 200
9 100
78 000
110 000
88 000
17 600
24 800
19 800
8 000
8 000
7 500
9 000
9 000
8 500
0.23
0.32
0.27
0.50
0.70
0.60
68
72
72
2.6772
2.8346
2.8346
35
25
35
1.3780
0.9843
1.3780
52 300
41 800
55 000
11 800
9 400
12 400
122 000
96 500
134 000
27 500
21 700
30 200
7 500
6 700
6 700
8 500
7 500
7 500
0.38
0.27
0.38
0.80
0.60
0.80
2.3622
2.3622
2.5591
82
82
90
3.2283
3.2283
3.5433
25
35
25
0.9843
1.3780
0.9843
44 000
60 500
52 800
9 900
13 700
11 900
95 000
146 000
106 000
21 400
32 900
23 900
6 000
6 000
5 600
6 700
6 700
6 300
0.39
0.55
0.47
0.90
1.20
1.00
65
70
70
2.5591
2.7559
2.7559
90
95
95
3.5433
3.7402
3.7402
35
25
35
1.3780
0.9843
1.3780
73 700
56 100
76 500
16 600
12 700
17 200
163 000
127 000
190 000
36 700
28 600
42 800
5 600
5 000
5 000
6 300
5 600
5 600
0.66
0.52
0.74
1.50
1.10
1.60
NKI 75/25
NKI 75/35
NKI 80/25
75
75
80
2.9528
2.9528
3.1496
105
105
110
4.1339
4.1339
4.3307
25
35
25
0.9843
1.3780
0.9843
69 300
96 800
72 100
15 600
21 800
16 300
132 000
200 000
140 000
29 700
45 000
31 500
4 800
4 800
4 500
5 300
5 300
5 000
0.64
0.91
0.68
1.40
2.00
1.50
NKI 80/35
NKI 85/26
NKI 85/36
80
85
85
3.1496
3.3465
3.3465
110
115
115
4.3307
4.5276
4.5276
35
26
36
1.3780
1.0236
1.4173
101 000
73 700
105 000
22 800
16 600
23 700
216 000
146 000
232 000
48 600
32 900
52 200
4 500
4 300
4 300
5 000
4 800
4 800
0.96
0.74
1.05
2.10
1.60
2.30
NKI 90/26
NKI 90/36
NKI 95/26
90
90
95
3.5433
3.5433
3.7402
120
120
125
4.7244
4.7244
4.9213
26
36
26
1.0236
1.4173
1.0236
76 500
108 000
78 100
17 200
24 300
17 600
156 000
250 000
166 000
35 100
56 200
37 400
4 000
4 000
3 800
4 500
4 500
4 300
0.78
1.10
0.82
1.70
2.40
1.80
NKI 95/36
NKI 100/30
NKI 100/40
95
100
100
3.7402
3.9370
3.9370
125
130
130
4.9213
5.1181
5.1181
36
30
40
1.4173
1.1811
1.5748
112 000
96 800
123 000
25 200
21 800
27 700
265 000
220 000
305 000
59 600
49 500
68 600
3 800
3 600
3 600
4 300
4 000
4 000
1.15
0.99
1.35
2.50
2.20
3.00
in
NKI 38/20
NKI 38/30
NKI 40/20
38
38
40
1.4961
1.4961
1.5748
53
53
55
2.0866
2.0866
2.1654
20
30
20
NKI 40/30
NKI 42/20
NKI 42/30
40
42
42
1.5748
1.6535
1.6535
55
57
57
2.1654
2.2441
2.2441
NKI 45/25
NKI 45/35
NKI 50/25
45
45
50
1.7717
1.7717
1.9685
62
62
68
NKI 50/35
NKI 55/25
NKI 55/35
50
55
55
1.9685
2.1654
2.1654
NKI 60/25
NKI 60/35
NKI 65/25
60
60
65
NKI 65/35
NKI 70/25
NKI 70/35
Static
C0
Mass
Reference
speed
r/min
mm
Dynamic
C
Speed rating
Limiting
speed
r/min
kg
lb
200
Single row
with inner ring
Series: NKIS 17 NKIS 100
Size: 17 mm 100 mm
0.6693 in 3.9370 in
Series NA 49
Series NKIS
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
B
mm
in
lbf
lbf
0.7874
0.7874
0.8661
26 000
28 600
34 100
5 900
6 500
7 700
33 500
39 000
46 500
7 600
8 800
10 500
15 000
13 000
12 000
17 000
15 000
13 000
0.10
0.13
0.16
0.20
0.30
0.40
22
22
22
0.8661
0.8661
0.8661
36 000
39 100
42 900
8 100
8 800
9 700
54 000
61 000
72 000
12 200
13 800
16 200
10 000
9 000
8 000
12 000
10 000
9 000
0.18
0.22
0.28
0.40
0.50
0.60
2.8346
3.1496
3.3465
22
28
28
0.8661
1.1024
1.1024
44 600
62 700
66 000
10 100
14 100
14 900
78 000
104 000
114 000
17 600
23 400
25 700
7 000
6 300
6 000
8 000
7 500
6 700
0.34
0.52
0.56
0.70
1.10
1.20
90
95
100
3.5433
3.7402
3.9370
28
28
28
1.1024
1.1024
1.1024
68 200
70 400
74 800
15 400
15 900
16 900
120 000
132 000
140 000
27 000
29 700
31 500
5 600
5 300
5 000
6 300
6 000
5 600
0.56
0.64
0.68
1.20
1.40
1.50
135
5.3150
32
1.2598
91 300
20 600
220 000
49 500
3 600
4 000
1.34
3.00
in
NKIS 17
NKIS 20
NKIS 25
17
20
25
0.6693
0.7874
0.9843
37
42
47
1.4567
1.6535
1.8504
20
20
22
NKIS 30
NKIS 35
NKIS 40
30
35
40
1.1811
1.3780
1.5748
52
58
65
2.0472
2.2835
2.5591
NKIS 45
NKIS 50
NKIS 55
45
50
55
1.7717
1.9685
2.1654
72
80
85
NKIS 60
NKIS 65
NKIS 70
60
65
70
2.3622
2.5591
2.7559
NKIS 100
100
3.9370
Static
C0
Mass
Reference
speed
r/min
mm
Dynamic
C
Speed rating
Limiting
speed
r/min
kg
lb
201

Single row
without inner ring
Series: NKS 20 NKS 80
Size: 20 mm 80 mm
0.7874 in 3.1496 in
Series NKS
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
NKS 20
NKS 24
NKS 25
20
24
25
0.7874
0.9449
0.9843
32
37
38
1.2598
1.4567
1.4961
20
20
20
0.7874
0.7874
0.7874
23 300
26 000
27 500
5 300
5 900
6 200
27 000
33 500
36 000
6 100
7 600
8 100
18 000
15 000
15 000
20 000
17 000
17 000
0.05
0.07
0.07
0.10
0.10
0.10
NKS 28
NKS 30
NKS 32
28
30
32
1.1024
1.1811
1.2598
42
45
47
1.6535
1.7717
1.8504
20
22
22
0.7874
0.8661
0.8661
28 600
31 900
34 100
6 500
7 200
7 700
39 000
43 000
46 500
8 800
9 700
10 500
13 000
12 000
12 000
15 000
14 000
14 000
0.08
0.10
0.11
0.20
0.20
0.20
NKS 35
NKS 37
NKS 40
35
37
40
1.3780
1.4567
1.5478
50
52
55
1.9685
2.0472
2.1654
22
22
22
0.8661
0.8661
0.8661
35 200
36 900
38 000
8 000
8 300
8 600
50 000
54 000
57 000
11 300
12 200
12 900
11 000
10 000
9 500
12 000
12 000
11 000
0.12
0.12
0.13
0.30
0.30
0.30
NKS 43
NKS 45
NKS 50
43
43
50
1.6929
1.6929
1.9685
58
60
65
2.2835
2.3622
2.5591
22
22
22
0.8661
0.8661
0.8661
39 100
40 200
42 900
8 800
9 100
9 700
61 000
64 000
72 000
13 800
14 400
16 200
9 000
8 500
8 000
10 000
10 000
9 000
0.14
0.15
0.16
0.30
0.30
0.40
NKS 55
NKS 60
NKS 65
55
60
65
2.1654
2.3622
2.5591
72
80
85
2.8346
3.1496
3.3465
22
28
28
0.8661
1.1024
1.1024
44 600
62 700
66 000
10 100
14 100
14 900
78 000
104 000
114 000
17 600
23 400
25 700
7 000
6 300
6 000
8 000
7 500
6 700
0.22
0.34
0.36
0.50
0.70
0.80
NKS 70
NKS 75
NKS 80
70
75
80
2.7559
2.9528
3.1496
90
95
100
3.5433
3.7402
3.9370
28
28
28
1.1024
1.1024
1.1024
68 200
70 400
74 800
15 400
15 900
16 900
120 000
132 000
140 000
27 000
29 700
31 500
5 600
5 300
5 000
6 300
6 000
5 600
0.38
0.40
0.40
0.80
0.90
0.90
202
Single row
without inner ring
Series: RNA 4822 RNA 4860
Size: 120 mm 330 mm
4.7244 in 12.9921 in
Fw
Series RNA 48
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
RNA 4822
RNA 4824
RNA 4826
120
130
145
4.7244
5.1181
5.7087
140
150
165
5.5118
5.9055
6.4961
30
30
35
RNA 4828
RNA 4830
RNA 4832
155
165
175
6.1024
6.4961
6.8898
175
190
200
6.8898
7.4803
7.8740
RNA 4834
RNA 4836
RNA 4838
185
195
210
7.2835
7.6772
8.2677
215
225
240
RNA 4840
RNA 4844
RNA 4848
220
240
265
8.6614
9.4488
10.4430
RNA 4852
RNA 4856
RNA 4860
285
305
330
11.2205
12.0079
12.9921
Dynamic
C
Static
C0
N
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
lbf
1.1811
1.1811
1.3780
93 500
99 000
119 000
21 100
22 300
26 800
232 000
255 000
325 000
52 200
57 400
73 100
3 400
3 200
2 800
3 800
3 600
3 200
0.67
0.73
0.99
1.50
1.60
2.20
35
40
40
1.3780
1.5748
1.5748
121 000
147 000
157 000
27 300
33 100
35 300
345 000
415 000
450 000
77 600
93 300
101 200
2 600
2 400
2 200
3 000
2 800
2 600
1.05
1.60
1.70
2.30
3.50
3.70
8.4646
8.8583
9.4488
45
45
50
1.7717
1.7717
1.9685
179 000
190 000
220 000
40 300
42 800
49 500
520 000
570 000
710 000
116 900
128 200
159 700
2 200
2 000
1 900
2 400
2 400
2 200
2.55
2.70
3.20
5.60
6.00
7.10
250
270
300
9.8425
10.6299
11.8110
50
50
60
1.9685
1.9685
2.3622
224 000
238 000
347 000
50 400
53 600
78 100
735 000
815 000
1 120 000
165 300
183 300
251 800
1 800
1 700
1 500
2 000
1 900
1 700
3.35
3.60
5.40
7.40
7.90
11.90
320
350
380
12.5984
13.7795
14.9606
60
69
80
2.3622
2.7165
3.1496
358 000
429 000
594 000
80 500
96 500
133 600
1 200 000
1 320 000
1 800 000
269 800
296 800
404 700
1 400
1 300
1 100
1 500
1 400
1 300
5.80
9.30
12.50
12.80
20.50
27.60
203

Single row
without inner ring
Open and sealed
Size: 14 mm 85 mm
0.5512 in 3.3465 in
Fw
Series RNA 2RS
Series RNA 49
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
N
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
RNA 4900
RNA 4900 2RS
RNA 4901
14
14
16
0.5512
0.5512
0.6299
22
22
24
0.8661
0.8661
0.9449
13
13
13
0.5118
0.5118
0.5118
8 800
7 370
9 900
2 000
1 700
2 300
10 400
8 150
12 200
2 400
1 900
2 800
26 000
22 000
30 000
12 000
26 000
0.02
0.02
0.02
0.04
0.04
0.04
RNA 4901 2RS

RNA 4902
RNA 4902 2RS
16
20
20
0.6299
0.7874
0.7874
24
28
28
0.9449
1.1024
1.1024
13
13
13
0.5118
0.5118
0.5118
8 090
11 200
9 130
1 900
2 600
2 100
9 650
15 300
12 000
2 200
3 500
2 700
19 000
11 000
22 000
9 500
0.02
0.02
0.02
0.04
0.05
0.05
RNA 4903
RNA 4903 2RS
RNA 4904
22
22
25
0.8661
0.8661
0.9843
30
30
37
1.1811
1.1811
1.4567
13
13
17
0.5118
0.5118
0.6693
11 400
9 520
21 600
2 600
2 200
4 900
16 300
12 900
28 000
3 700
2 900
6 300
18 000
15 000
20 000
9 000
17 000
0.02
0.02
0.05
0.05
0.05
0.10
RNA 4904 2RS

RNA 49/22
RNA 4905
25
28
30
0.9843
1.1024
1.1811
37
39
42
1.4567
1.5354
1.6535
17
17
17
0.6693
0.6693
0.6693
19 400
23 300
24 200
4 400
5 300
5 500
22 400
32 000
34 500
5 100
7 200
7 800
14 000
13 000
7 500
15 000
15 000
0.06
0.05
0.06
0.10
0.10
0.10
RNA 4905 2RS

RNA 49/28
RNA 4906
30
32
35
1.1811
1.2598
1.3780
42
45
47
1.6535
1.7717
1.8504
17
17
17
0.6693
0.6693
0.6693
21 600
25 100
25 500
4 900
5 700
5 800
27 500
36 500
39 000
6 200
8 300
8 800
12 000
11 000
6 300
14 000
13 000
0.06
0.07
0.07
0.10
0.20
0.20
RNA 4906 2RS

RNA 49/32
RNA 4907
35
40
42
1.3780
1.5748
1.6535
47
52
55
1.8504
2.0472
2.1654
17
20
20
0.6693
0.7874
0.7874
23 300
30 800
31 900
5 300
7 000
7 200
32 000
51 000
54 000
7 200
11 500
12 200
10 000
9 500
5 600
11 000
11 000
0.07
0.09
0.11
0.20
0.20
0.20
RNA 4907 2RS

RNA 4908
RNA 4908 2RS
42
48
48
1.6535
1.8898
1.8898
55
62
62
2.1654
2.4409
2.4409
20
22
22
0.7874
0.8661
0.8661
27 000
42 900
36 900
6 100
9 700
8 300
43 000
71 000
58 500
9 700
16 000
13 200
8 000
4 800
9 500
4 000
0.11
0.14
0.15
0.20
0.30
0.30
RNA 4909
RNA 4909 2RS
RNA 4910
52
52
58
2.0472
2.0472
2.2835
68
68
72
2.6772
2.6772
2.8346
22
22
22
0.8661
0.8661
0.8661
45 700
39 100
47 300
10 300
8 800
10 700
78 000
64 000
85 000
17 600
14 400
19 200
7 500
7 000
8 500
3 800
8 000
0.18
0.16
0.16
0.40
0.40
0.40
RNA 4910 2RS

RNA 4911
RNA 4912
58
63
68
2.2835
2.4803
2.6772
72
80
85
2.8346
3.1496
3.3465
22
25
25
0.8661
0.9843
0.9843
40 200
57 200
60 500
9 100
12 900
13 700
69 500
106 000
114 000
15 700
23 900
25 700
6 300
6 000
3 400
7 000
6 700
0.16
0.26
0.28
0.40
0.60
0.60
RNA 4913
RNA 4914
RNA 4915
72
80
85
2.8346
3.1496
3.3465
90
100
105
3.5433
3.9370
4.1339
25
30
30
0.9843
1.1811
1.1811
61 600
84 200
84 200
13 900
19 000
19 000
120 000
163 000
170 000
27 000
36 700
38 300
5 600
5 000
4 800
6 300
5 600
5 300
0.31
0.46
0.49
0.70
1.00
1.10
204
Single row
without inner ring
Size: 90 mm 150 mm
3.5433 in 5.9055 in
Fw
Series RNA 49
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
RNA 4916
RNA 4917
RNA 4918
90
100
105
3.5433
3.9370
4.1339
110
120
125
4.3307
4.7244
4.9213
30
35
35
RNA 4919
RNA 4920
RNA 4924
110
115
135
4.3307
4.5276
5.3150
130
140
165
5.1181
5.5118
6.4961
RNA 4926
150
5.9055
180
7.0866
Dynamic
C
Static
C0
N
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
lbf
1.1811
1.3780
1.3780
88 000
108 000
112 000
19 800
24 300
25 200
183 000
250 000
265 000
41 200
56 200
59 600
4 500
4 000
3 800
5 000
4 500
4 300
0.52
0.66
0.75
1.10
1.50
1.70
35
40
45
1.3780
1.5748
1.7717
114 000
125 000
176 000
25 700
28 100
39 600
270 000
280 000
405 000
60 700
63 000
91 100
3 600
3 400
3 000
4 000
4 000
3 400
0.72
1.15
1.85
1.60
2.50
4.10
50
1.9685
198 000
44 600
480 000
108 000
2 600
3 000
2.20
4.90
205

Double row
without inner ring
Size: 16 mm 110 mm
0.6299 in 4.3307 in
Fw
Series RNA 69
Designation
Basic load ratings
Speed rating
Mass
Diameter
Under rollers
Fw
mm
in
Outside diameter
D
mm
in
Width
C
mm
in
Dynamic
C
Static
C0
lbf
lbf
Reference
speed
r/min
Limiting
speed
r/min
kg
lb
RNA 6901
RNA 6902
RNA 6903
16
20
22
0.6299
0.7874
0.8661
24
28
30
0.9449
1.1024
1.1811
22
23
23
0.8661
0.9055
0.9055
16 100
17 200
18 700
3 600
3 900
4 200
23 200
27 000
30 500
5 200
6 100
6 900
22 000
19 000
18 000
26 000
22 000
20 000
0.03
0.04
0.04
0.07
0.09
0.09
RNA 6904
RNA 69/22
RNA 6905
25
28
30
0.9843
1.1024
1.1811
37
39
42
1.4567
1.5354
1.6535
30
30
30
1.1811
1.1811
1.1811
35 200
36 900
38 000
7 900
8 300
8 500
53 000
57 000
62 000
11 900
12 800
13 900
15 000
14 000
13 000
17 000
15 000
15 000
0.10
0.10
0.11
0.20
0.20
0.20
RNA 69/28
RNA 6906
RNA 69/32
32
35
40
1.2598
1.3780
1.5478
45
47
52
1.7717
1.8504
2.0472
30
30
36
1.1811
1.1811
1.4173
39 600
42 900
47 300
8 900
9 600
10 600
65 500
75 000
90 000
14 700
16 900
20 200
12 000
11 000
10 000
14 000
13 000
11 000
0.14
0.13
0.16
0.30
0.30
0.40
RNA 6907
RNA 6908
RNA 6909
42
48
52
1.6535
1.8898
2.0472
55
62
68
2.1654
2.4409
2.6772
36
40
40
1.4173
1.5748
1.5748
48 400
67 100
70 400
10 900
15 100
15 800
93 000
125 000
137 000
20 900
28 100
30 800
9 500
8 000
7 500
11 000
9 500
8 500
0.19
0.26
0.34
0.40
0.60
0.70
RNA 6910
RNA 6911
RNA 6912
58
63
68
2.2835
2.4803
2.6772
72
80
85
2.8346
3.1496
3.3465
40
45
45
1.5748
1.7717
1.7717
73 700
89 700
93 500
16 600
20 200
21 000
150 000
190 000
204 000
33 700
42 700
45 900
7 000
6 300
6 000
8 000
7 000
6 700
0.31
0.47
0.49
0.70
1.00
1.10
RNA 6913
RNA 6914
RNA 6915
72
80
85
2.8346
3.1496
3.3465
90
100
105
3.5433
3.9370
4.1339
45
54
54
1.7717
2.1260
2.1260
95 200
128 000
130 000
21 400
28 800
29 200
212 000
285 000
290 000
47 700
64 100
65 200
5 600
5 000
4 800
6 300
5 600
5 300
0.58
0.86
0.94
1.30
1.90
2.10
RNA 6916
RNA 6917
RNA 6918
90
100
105
3.5433
3.9370
4.1339
110
120
125
4.3307
4.7244
4.9213
54
63
63
2.1260
2.4803
2.4803
134 000
165 000
172 000
30 100
37 100
38 700
315 000
425 000
450 000
70 800
95 500
101 200
4 500
4 000
3 800
5 000
4 500
4 300
0.99
1.20
1.35
2.20
2.60
3.00
RNA 6919
110
4.3307
130
5.1181
63
2.4803
172 000
38 700
465 000
104 500
3 600
4 000
1.45
3.20
206
Taper roller
bearings (metric series)
Nomenclature
32302 B J2 / Q CL7C
1
3
4
2
1. Contact angle:
3. Features:
Larger contact angle

than standard
Improved friction torque

characteristics and
raceway geometry
2. Internal design:
4. Quality:
J2
Pressed steel cage

CL7C
Boundary dimensions changed

to conform to ISO standards
DF
Duplex (2) bearings, face-toface arrangement including

1 outer ring and 1 inner
ring spacer
DB
Duplex (2) bearings, back-toback face arrangement

including 1 outer and 1 inner
ring spacer
DT
Duplex (2) bearings arranged

in tandem with 1 outer ring
and 1 inner ring spacer
Special SKF quality for

pinion bearings
209
Taper roller bearings
Product
Details
Technical
features
Boundary dimensions
Tolerances
ISO-Normal
Heat stabilization
302 F (150 C)
Misalignment
(under heavy load
conditions)
2-4 minutes of arc (logarithmic profile rollers)
Cage Material
Standard
Steel
Optional
None
Axial load max
Contact SKF Applications Engineering
Seals
Not available
Single row
Taper roller bearing
210
Paired single row

Introduction
Introduction
Basic design
Taper roller bearings have tapered inner and

outer ring raceways between which tapered
rollers are arranged. If extended, the tapered
surfaces converge towards a single point on
the bearing axis. This means that rolling
conditions are at an optimum.
Their design makes taper roller bearings
particularly suitable for the accommodation of
combined (radial and axial) loads. The axial
load carrying capacity of the bearings is largely
determined by the contact angle a, which
corresponds to the angle of the outer ring
raceway. The larger this angle, the larger the
axial load carrying capacity. Taper roller bearings are generally of separable design; for
example, the inner ring with roller and cage
assembly forms a unit which can be mounted
separately from the outer ring.
Single row taper roller bearings are able
to accommodate axial loads acting in one
direction only. Under radial loads, an axial
force is produced in the bearing which must
be counteracted. Therefore, it is customary for
the single row taper roller bearings to be
adjusted against a second taper roller bearing.
SKF manufactures single and double row
taper roller bearings with metric dimensions.
The single row bearings listed in the following
product tables are the most prevalent. Double
row taper roller bearings are also included in
this catalog.
Single row taper roller bearings

Continuous improvements made to SKF taper
roller bearings resulted in the latest state of the
art design known as the TQ-line (suffix Q). The
sliding surfaces of the inner ring guide flange
and the roller ends have been redesigned to
enable lubricant feed to the roller end / flange
contacts to be enhanced and lubricant film
formation in the contacts to be considerably
improved. The contact geometry between
rollers and raceways has also been markedly
improved by the "logarithmic" profile, which
provides for optimum stress distribution in the
bearing. Optimized raceway surfaces promote
lubricant film formation and correct motion of
the rollers. These improvements have considerably enhanced the performance of SKF taper
roller bearings.
Metric bearings
When the current international standard
(ISO 355-1977) was prepared, new designations were devised for the Dimension series,
and consequently, for the bearings.
However, since changes in bearing designations cause difficulties, and if introduced would
necessitate the alteration of drawings, part lists,
etc., both by producer and user, it was decided
that the SKF designations for those bearings,
which were in accordance with the earlier
ISO/R 355 as well as the new standard, would
be retained. New designations comprising the
three symbols of the series designation to ISO,
prefixed by the letter T and followed by a
three-figure identification of the bore diameter
in mm were adopted only for the bearing
sizes, which were new to the ISO 355-1977
standard; for example, T2ED 045.
Product highlights
Suitable for heavy loads
Taper roller bearings are designed for
heavy combined axial and radial loads.
Offer longer life and higher

reliability
SKFs latest state-of-the-art taper
roller bearing design is less sensitive to
misalignment (up to two minutes of
arc) and offers long life, high reliability
and low operating temperatures.
CL7C design offers high running

accuracy and low friction torque
These taper roller bearings operate
under full load without any running-in
risk or temperature peaks.

Available in a wide range of sizes
including 15 to 320 mm inside
diameter.
Quiet running
The outstanding running and dimensional accuracy allows for extremely
silent running conditions.
Depending on application needs, SKF
has the possibility to provide either
case-carburized or thru-hardened in
some sizes. Typical applications are
gearboxes, construction equipment,
wheel hubs, and mining bulk
conveyors.
SKF Explorer class

bearings
High performance taper roller bearings in the
SKF Explorer performance class are printed in
blue in the product tables. The higher performance of SKF Explorer bearings retain the
designation of the earlier standard bearings,
e.g. 32010 X/Q. However, each bearing and
its box are marked with the name SKF
page 23.
211

Introduction
Paired single row taper roller bearings

For bearing arrangements where the load carrying capacity of a single bearing is inadequate
or where the shaft has to be located in both
directions with a given axial play, SKF can
supply single row taper roller bearings as
ready-to-mount matched pairs.
Matched pairs of single row taper roller
bearings enable economic designs of bearing
arrangement to be made and can be supplied
by SKF in the arrangements shown in (Figure 1).
However, the use of the paired bearings in faceto-face arrangements shown in the product
tables on pages 226-228, which represent the
range currently produced, is recommended.
Other sets of bearings arranged face-to-face as
well as bearing sets arranged back-to-back or
in tandem can be supplied to order if the
quantities required are economic.
Where only a few sets are required it is
recommended that they be matched by
the user, following the instructions given in
SKF General Catalog 6000EN.
Matched pairs of bearings arranged face-toface are simple in design and easily produced
as they consist of two bearings with an intermediate ring between the two outer rings. The
load lines of bearings arranged face-to-face
converge towards the bearing axis. Axial loads
can be accommodated in both directions,
although only by one bearing at a time.
Where the bearing set has a back-to-back
arrangement, two intermediate rings are
needed: one between the outer rings and
one between the inner rings. Such sets are
therefore more expensive to produce. In a
back-to-back arrangement, the load lines of the
bearings diverge towards the bearing axis, so
that such bearing arrangements are relatively
stiff and can accommodate tilting moments.
Axial loads can again be accommodated in both
directions as for the face-to-face arrangement.
Sets of bearings arranged in tandem also
call for the use of two intermediate rings (one
between the inner and one between the outer
rings) but such sets are seldom required. The
load lines of bearings arranged in tandem are
parallel to each other so that radial and axial
loads are equally distributed over the bearing
pair. Axial loads can only be taken up in one
direction and the pair is usually adjusted against
a third bearing, which can take axial loads acting in the opposite direction.
Figure 1
CL7C design
Bearings to the CL7C specifications require
no running-in and a hydrodynamic lubricant
film is able to form in the roller end / flange
so that their friction torque almost from the
start of operation is as low as that of normal
bearings after running-in. The bearings can
be adjusted using the preload force / preload
path procedures as well as the friction torque,
as described in the SKF General Catalog
(publication #6000 EN).
Further information on CL7C design
bearings can be supplied on request.
Four-row tapered roller bearings

Face-to-face arrangement
(Suffix DF)
Four-row tapered roller bearings are used in

extremely heavy applications. Consult SKF
Applications Engineering for further details.
Metric bearing tolerances

SKF single row metric taper roller bearings
are manufactured to Normal tolerances as
standard. Some bearings are also available with
higher accuracy in particular those of series
320 X, T4CB and T4DB. Consult SKF
Applications Engineering for further details.
Inch series
SKF manufactures a limited assortment of
these bearings. Consult SKF USA Inc. prior to
design or ordering.
Back-to-back arrangement
(Suffix DB)
Tandem arrangement
(Suffix DT)
212
Variations
Introduction
Loads
Radial and side face runouts of bearings to CL7C specifications

d, D*
over
mm
incl.
inches

single row taper roller bearings
Kia
Kea
max
m
in
max
m
Sia Sea
in
max
m
in
10
18
30
18
30
50
0.3937
0.7087
1.1811
0.7087
1.1811
1.9685
7
8
10
0.0003
0.0003
0.0004
9
10
0.0004
0.0004
38
38
38
0.0015
0.0015
0.0015
50
80
120
80
120
150
1.9685
3.1496
4.7244
3.1496
4.7244
5.9055
10
13
-
0.0004
0.0005
-
13
18
20
0.0005
0.0007
0.0008
38
38
38
0.0015
0.0015
0.0015
150
180
5.9055
7.0866
23
0.0009
38
0.0015
*Use "d" for Kia values, use "D" for Kea values.
Symbols
d
D
Kia
Kea
Sia
Sea
Nominal bore diameter

Nominal outside diameter
Radial runout of assembled bearing
inner ring
Radial runout of assembled bearing
outer ring
Side face runout with reference
to raceway of assembled bearing
inner ring
Side face runout with reference
to raceway of assembled bearing
outer ring
Internal clearance
Axial internal clearance single row
The internal clearance of single row taper roller
bearings can only be obtained after mounting
and is determined by adjustment of the bearing
against a second bearing which provides location in the opposite direction. Further details will
be found in SKF General Catalog (6000 EN).

paired tapered roller bearings
The axial internal clearance of paired single row
taper roller bearings is determined by the intermediate rings between the two bearings of the
matched pair. The bearing pairs shown in the
bearing tables are produced with the standard
bearing clearance shown in Table 1. The values
apply to bearings before they are mounted and
under measuring loads of
100 N for bearings with an outside
diameter D 90 mm
diameter 90 < D 240 mm
diameter D > 240 mm
Matched bearing sets having a clearance
other than the standard value are identified by
the designation suffix C followed by a two-or
three-figure number, which gives the mean
axial clearance in m. The range of the special
clearance is, however, the same as for the standard clearance; for example, for the bearing set
designated 32048 X / DFC205, having a mean
axial clearance of 205 m, the clearance limits
are 175 and 235 m since the range from the
table below for a 320X series bearing with
240 mm bore is 500 - 440 = 60 m.
P = Fr where Fa / Fr e
P = 0.4 Fr + YFa where Fa / Fr > e
The values of factors e and Y will be found
in the bearing tables for each individual
bearing.
Because the raceways are at an angle to the
bearing axis, when taper roller bearings are
subjected to a radial load, an axial force is
induced within the bearing. This must be considered when calculating the equivalent dynamic
bearing load. All the requisite equations for the
various bearing arrangements and load cases
are given on the following page. These are only
valid if the bearings are adjusted against each
other to give zero clearance in operation, but
are without preload. Values for the axial load
factor Y for bearings can be found in the
bearing tables.

two bearings arranged face-to-face
in a matched set
P = Fr + YFa where Fa / Fr e
P = 0.67 Fr + Y2Fa where Fa / Fr > e
Fr and Fa are the forces acting on the bearing
pair. Values of the factors e, Y1 and Y2 are given
for each bearing pair in the bearing tables; they
apply to the bearing pair.
Information regarding the calculation of the
equivalent load for sets of bearings arranged
back-to-back or in tandem will be found in
SKF General Catalog 6000EN.
213

Introduction
Table 1
Total width tolerances of matched single row metric taper roller bearings
Bore
diameter
Total width tolerance TsD of matched bearings of series

329
320 X
330
d
over
high
incl.
331, 302,
322, 332
303, 323
313 (X)
low
high
low
high
low
high
low
high
low
high
low
mm
mm
30
40
30
40
50
+550
+550
+600
+100
+100
+150
+550
+600
+600
+100
+150
+200
+600
+600
+600
+150
+150
+200
+500
+550
+550
+50
+50
+50
50
65
80
65
80
100
+750
150
+600
+600
+650
+150
+200
250
+800
50
+600
+650
+700
+200
+200
200
+650
+700
+700
+200
+200
100
+550
+600
+600
+100
+100
300
100
120
140
120
140
160
+750
+1 100
+1 150
150
200
150
+700
+1 000
+1 050
200
300
250
+800
+1 100
+1 100
100
200
200
+700
+1 000
+1 050
200
300
250
+750
+1 100
+1 150
150
200
150
+600
+950
+950
300
350
350
160
180
190
180
190
200
+1 150
+1 150
+1 150
150
150
150
+1 100
+1 100
+1 100
200
200
200
+1 100
+1 100
+1 100
200
200
200
+1 150
+1 200
+1 200
150
100
100
200
225
250
225
250
280
+1 200
+1 200
+1 300
100
100
0
+1 150
+1 200
+1 250
150
100
50
+1 150
+1 200
+1 250
150
100
50
+1 250
+1 300
50
0
280
300
315
300
315
340
+1 400
+1 400
+1 500
+100
+100
200
+1 300
+1 350
+1 450
0
+50
250
+1 300
+1 350
+1 450
0
+50
+200
303, 323
min
max
min
max
Axial internal clearance of matched single row metric taper roller bearings
Bore
diameter
d
over incl.
Axial internal clearance of matched bearings of series

329
320 X
330
mm
mm
min
max
min
max
min
max
331, 302,
322, 332
min
max
313 (X)
30
40
30
40
50
80
100
120
120
140
160
180
220
100
120
140
140
160
180
130
140
160
170
180
200
60
70
80
100
110
120
50
65
80
65
80
100
270
310
140
160
190
180
200
230
200
250
350
240
290
390
160
180
210
200
220
270
180
200
240
220
260
300
100
110
110
140
170
170
100
120
140
120
140
160
270
310
370
330
370
430
220
240
270
280
300
330
340
340
340
400
400
400
220
240
270
280
300
330
280
330
370
340
390
430
130
160
180
190
220
240
160
180
190
180
190
200
370
370
390
430
430
450
310
340
340
370
400
400
310
340
340
370
400
400
390
440
440
450
500
500
200
225
250
225
250
280
440
440
540
500
500
600
390
440
490
450
500
550
390
440
490
450
500
550
490
540
550
600
280
300
300
340
640
640
700
700
540
590
600
650
540
590
600
650
Note: To convert values to inches, multiply mm x .000039.
214
Introduction
Minimum load
In order to guarantee the satisfactory operation

of all ball and roller bearings, they must always
be subjected to a given minimum load. This is
also true of taper roller bearings, particularly if
they run at high speeds where the inertia forces
of the rollers and cage, and the friction in the
lubricant can have a detrimental influence on
the rolling conditions in the bearing and may
between the rollers and the raceways.
using the Interactive Engineering Catalog on the
SKF website www.skf.com or by contacting SKF
Applications Engineering. However, the weight of
the components supported by the bearing,
together with the external forces, often exceeds
case, an additional radial load must be applied
to the bearing by increasing belt tension or
similar means.

Design of bearing
arrangements
When designing bearing arrangements incorporating single row taper roller bearings, it is
necessary to consider the special characteristics
of these bearings. Because of their internal
design, they cannot be used singly and a
second bearing is required, or alternatively a
paired set (Figure 1, page 212) may be used.
Where the arrangement comprises two single
row taper roller bearings, they must be adjusted against each other until the desired operational clearance or requisite preload is achieved.
A correctly dimensioned operational clearance
or preload is vital to the correct performance of
single row taper roller bearings and also to the
operational reliability of the bearing arrangement. If the operational clearance is too great,
then the full load carrying capacity of the
bearing will not be exploited and if the preload
is too large then frictional losses will be greater,
the operating temperature higher and the
life shorter.
215

Single row
Series: 30203 30248
Size: 17 mm 240 mm
0.6693 in 9.4488 in
Designation
Bore
d
Basic load ratings
Outside diameter
Width
D
T
mm
in
mm
in
Dynamic
C
N
lbf
Speed rating
Calculation
factors
lbf
Reference Limiting
speed speed
r/min r/min
kg
lb
Static
C0
N
Mass
mm
in
30203
30204
30205
17
20
25
0.6693
0.7874
0.9843
40
47
52
1.5748 13.25
1.8504 15.25
2.0472 16.25
0.5217
0.6004
0.6398
19 000
27 500
30 800
4 270
6 180
6 920
18 600
28 000
33 500
4 200
6 300
7 600
13 000 18 000
11 000 15 000
10 000 13 000
0.075
0.12
0.15
0.17
0.30
0.40
0.35 1.70
0.35 1.70
0.37 1.60
30206
30207
30208
30
35
40
1.1811
1.3780
1.5748
62
72
80
2.4409 17.25
2.8346 18.25
3.1496 19.75
0.6791
0.7185
0.7776
40 200
51 200
61 600
9 040
11 510
13 850
44 000
56 000
68 000
9 900
12 600
15 300
8 500 11 000
7 000 9 500
6 300 8 500
0.23
0.32
0.42
0.60
0.80
1.00
0.37 1.60
0.37 1.60
0.37 1.60
30209
30210
30211
45
50
55
1.7717
1.9685
1.9685
85
90
100
3.3465 20.75
3.5433 21.75
3.937 22.75
0.8169
0.8563
0.8957
66 000
76 500
104 000
14 840
17 200
23 370
76 500
91 500
106 000
17 200
20 600
23 900
6 000
5 600
5 300
8 000
7 500
6 700
0.48
0.54
0.70
1.10
1.20
1.60
0.40 1.50
0.43 1.40
0.40 1.50
30212
30213
30214
60
65
70
2.3622
2.5591
2.7559
110
120
125
4.3307 23.75
4.7244 24.75
4.9213 26.25
0.9350
0.9744
1.0335
112 000
132 000
125 000
25 170
29 670
28 100
114 000
134 000
156 000
25 700
30 200
35 100
5 000
4 500
4 000
6 000
5 600
5 300
0.88
1.15
1.25
2.00
2.60
2.80
0.40 1.50
0.40 1.50
0.43 1.40
30215
30216
30217
75
80
85
2.9528
3.1496
3.3465
130
140
150
5.1181 27.25
5.5118 28.25
5.9055 30.50
1.0728
1.1122
1.2008
140 000
151 000
176 000
31 470
33 940
39 560
176 000
183 000
220 000
39 600
41 200
49 500
3 800
3 400
3 200
5 000
4 800
4 300
1.40
1.60
2.05
3.10
3.60
4.60
0.43 1.40
0.43 1.40
0.43 1.40
30218
30219
30220
90
95
100
3.5433
3.7402
3.9370
160
170
180
6.2992 32.50
6.6929 34.50
7.0866 37.00
1.2795
1.3583
1.4567
194 000
216 000
246 000
43 610
48 550
55 300
245 000
275 000
320 000
55 100
61 900
72 000
3 000
2 800
2 800
4 000
3 800
3 600
2.55
3.00
3.65
5.70
6.70
8.10
0.43 1.40
0.43 1.40
0.43 1.40
30221
30222
30224
105
110
120
4.1339
4.3307
4.7244
190
200
215
7.4803 39.00
7.8740 41.00
8.4646 43.50
1.5354
1.6142
1.7126
270 000
308 000
341 000
60 690
69 230
76 650
355 000
405 000
465 000
79 900
91 100
104 600
2 600
2 400
2 200
3 400
3 200
3 000
4.25
5.10
6.15
9.40
11.30
13.60
0.43 1.40
0.43 1.40
0.43 1.40
30226
30228
30230
130
140
150
5.1181
5.5118
5.9055
230
250
270
9.0551 43.75
9.8425 45.75
10.6299 49.00
1.7224
1.8012
1.9291
369 000
418 000
429 000
82 950
93 960
96 430
490 000
570 000
560 000
110 200
128 200
125 900
2 000
1 900
1 800
2 800
2 600
2 400
7.60
8.65
11.00
16.80
19.10
24.30
0.43 1.40
0.43 1.40
0.43 1.40
30232
30234
30236
160
170
180
6.2992
6.6929
7.0866
290
310
320
11.4173 52.00
12.2047 57.00
12.5984 57.00
2.0472
2.2441
2.2441
528 000 118 700

616 000 138 500
583 000 131 100
735 000
865 000
815 000
165 300
194 500
183 300
1 600
1 500
1 500
2 200
2 000
2 000
13.00
19.00
20.00
28.70
41.90
44.10
0.43 1.40
0.43 1.40
0.46 1.30
30238
30240
30244
190
200
220
7.4803
7.8740
8.6614
340
360
400
13.3858 60.00
14.1732 64.00
15.7480 72.00
2.3622
2.5197
2.8346
721 000 162 080 1 000 000

792 000 178 040 1 120 000
990 000 222 550 1 400 000
224 800
251 800
314 800
1 400
1 300
1 200
1 800
1 700
1 600
24.00
25.00
40.00
53.00
55.20
88.20
0.43 1.40
0.43 1.40
0.43 1.40
30248
240
9.4488
440
17.3228 79.00
3.1102 1 210 000 272 000 1 760 000
395 700
1 000
1 400
46.76 103.10
0.43 1.40
216
Single row
Series: 30302 30352
Size: 15 mm 260 mm
0.5906 in 10.2362 in
Designation
Bore
d
Outside diameter
D
mm
in
mm
in
30302
30303
30304
15
17
20
0.5906
0.6693
0.7874
42
47
52
30305
30306
30307
25
30
35
0.9843
1.1811
1.3780
30308
30309
30310
40
45
50
30311
30312
30313
Basic load ratings

Width
T
Dynamic
C
Speed rating
Static
C0
Mass
Calculation
factors
lbf
Reference Limiting
speed speed
r/min r/min
kg
lb
mm
in
lbf
1.6535
1.8504
2.0472
14.25
15.25
16.25
0.5610
0.6004
0.6398
22 400
28 100
34 100
5 030
6 310
7 670
20 000
25 000
32 500
4 500
5 700
7 400
13 000 18 000
12 000 16 000
11 000 14 000
0.10
0.13
0.17
0.30
0.30
0.40
0.28 2.10
0.28 2.10
0.30 2.00
62
72
80
2.4409
2.8346
3.1496
18.25
20.75
22.75
0.7185
0.8169
0.8957
44 600
56 100
72 100
10 020
12 610
16 210
43 000
56 000
73 500
9 700
12 600
16 600
9 000 12 000
7 500 10 000
6 700 9 000
0.26
0.39
0.52
0.60
0.90
1.20
0.30 2.00
0.31 1.90
0.31 1.90
1.5748
1.7717
1.9685
90
100
110
3.5433
3.9370
4.3307
25.25
27.25
29.25
0.9941
1.0728
1.1516
85 800
108 000
143 000
19 290
24 280
32 140
95 000
120 000
140 000
21 400
27 000
31 500
6 000
5 300
5 300
8 000
7 000
6 300
0.72
0.97
1.25
1.60
2.20
2.80
0.35 1.70
0.35 1.70
0.83 0.72
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
31.50
33.50
36.00
1.2402
1.3189
1.4173
166 000
168 000
194 000
37 310
37 760
43 610
163 000
196 000
228 000
36 700
44 100
51 300
4 800
4 000
3 600
5 600
5 300
4 800
1.55
1.95
2.40
3.50
4.30
5.30
0.88 0.68
0.83 0.72
0.35 1.70
30314
30315
30316
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
38.00
40.00
42.50
1.4961
1.5748
1.6732
220 000
246 000
270 000
49 450
55 300
60 690
260 000
290 000
320 000
58 500
65 200
72 000
3 400
3 200
3 000
4 500
4 300
4 300
2.90
3.45
4.10
6.40
7.70
9.10
0.35 1.70
0.35 1.70
0.35 1.70
30317
30318
30319
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866
7.4803
7.8740
44.50
46.50
49.50
1.7520
1.8307
1.9488
303 000
330 000
330 000
68 110
74 180
74 180
365 000
400 000
390 000
82 100
90 000
87 700
2 800
2 600
2 600
4 000
4 000
3 400
4.85
5.65
6.70
10.70
12.50
14.80
0.35 1.70
0.35 1.70
0.35 1.70
30320
30322
30324
100
110
120
3.9370
4.3307
4.7244
215
240
260
8.4646
9.4488
10.2362
51.50
54.50
59.50
2.0276
2.1457
2.3425
402 000
90 360
473 000 106 330
561 000 126 110
490 000
585 000
710 000
110 200
131 600
159 700
2 400
2 200
2 000
3 200
2 800
2 600
8.05
11.00
14.00
17.80
24.30
30.90
0.35 1.70
0.35 1.70
0.35 1.70
30326
30332
30334
130
160
170
5.1181
6.2992
6.6929
280
340
360
11.0236
13.3858
14.1732
63.75
75.00
80.00
2.5098
627 000 140 940
800 000
2.9528
913 000 205 240 1 180 000
3.1496 1 020 000 229 000 1 340 000
179 900
265 300
301 000
1 800
1 500
1 400
2 400
2 000
1 800
17.00
29.00
35.00
37.50
64.00
77.20
0.35 1.70
0.35 1.70
0.35 1.70
30352
260
10.2362
540
21.2598 113.00
4.4488 2 120 000 476 570 3 050 000
685 700
850
1 200
110.00 242.60
0.35 1.70
217

Single row
Series: 31305 31330 X
Size: 25 mm 150 mm
0.9843 in 5.9055 in
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings
in
lbf
lbf
Reference Limiting
speed speed
r/min r/min
2.4409 18.25
2.8346 20.75
3.1496 22.75
0.7185
0.8169
0.8957
38 000
47 300
61 600
8 540
10 630
13 850
40 000
50 000
67 000
9 000
11 300
15 100
90
100
110
3.5433 25.25
3.9370 27.25
4.3307 29.25
0.9941
1.0728
1.1516
85 000
106 000
122 000
19 100
23 820
27 420
81 500
102 000
120 000
2.1654
2.3622
2.5591
120
130
140
4.7244 31.50
5.1181 33.50
5.5118 36.00
1.2402
1.3189
1.4173
121 000
145 000
165 000
27 200
32 600
37 090
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055 38.00
6.2992 40.00
6.6929 42.50
1.4961
1.5748
1.6732
187 000
209 000
224 000
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866 44.50
7.4803 46.50
7.8740 49.50
1.7520
1.8307
1.9488
242 000
264 000
292 000
31320 X
31322 X
31324 X
100
110
120
3.9370
4.3307
4.7244
215
240
260
8.4646 56.50
9.4488 63.00
10.2362 68.00
31326 X
31328 X
31330 X
130
140
150
5.1181
5.5118
5.9055
280
300
320
11.0236 72.00
11.8110 77.00
12.5984 82.00
mm
in
31305
31306
31307
25
30
35
0.9843
1.1811
1.3780
62
72
80
31308
31309
31310
40
45
50
1.5748
1.7717
1.9685
31311
31312
31313
55
60
65
31314
31315
31316
31317
31318
31319
Width
T
mm
Dynamic
C
Speed rating
Static
C0
Mass
Calculation
factors
kg
lb
7 500 11 000
6 700 9 500
6 000 8 500
0.26
0.39
0.52
0.60
0.90
1.20
0.83 0.72
0.83 0.72
0.83 0.72
18 400
23 000
27 000
5 600
5 000
4 500
7 500
6 700
6 000
0.72
0.95
1.20
1.60
2.10
2.70
0.83 0.72
0.83 0.72
0.35 1.70
137 000
166 000
193 000
30 800
37 400
43 400
3 800
3 600
3 200
5 600
5 300
4 800
1.55
1.90
2.35
3.50
4.20
5.20
0.35 1.70
0.35 1.70
0.83 0.72
42 040
46 980
50 360
220 000
245 000
265 000
49 500
55 100
59 600
3 000
2 800
2 800
4 500
4 300
4 000
2.95
3.50
4.05
6.60
7.80
9.00
0.83 0.72
0.83 0.72
0.83 0.72
54 400
59 340
65 640
285 000
315 000
355 000
64 100
70 900
79 900
2 600
2 400
2 400
3 800
3 400
3 400
4.60
5.90
6.95
10.20
13.10
15.40
0.83 0.72
0.83 0.72
0.83 0.72
2.2244
2.4803
2.6772
374 000
84 080
457 000 102 700
539 000 121 200
465 000
585 000
695 000
104 600
131 600
156 300
2 200
1 900
1 700
3 000
2 800
2 400
8.60
12.00
15.50
19.00
26.50
34.20
0.83 0.72
0.83 0.72
0.83 0.72
2.8346
3.0315
3.2283
605 000 136 000

780 000
693 000 155 800
900 000
781 000 175 600 1 020 000
175 400
202 400
229 300
1 600
1 500
1 400
2 400
2 200
2 000
18.50
24.50
29.50
40.80
54.10
65.10
0.83 0.72
0.83 0.72
0.83 0.72
218
Single row
Series: 32004 X 32040 X
Size: 20 mm 200 mm
0.7874 in 7.8740 in
Designation
Bore
d
Outside diameter
D
mm
in
mm
in
32004 X
32005 X
320/28 X
20
25
28
0.7874
0.9843
1.1024
42
47
52
32006 X
320/32 X
32007 X
30
32
35
1.1811
1.2598
1.3780
32008 X
32009 X
32010 X
40
45
50
32011 X
32012 X
32013 X
Basic load ratings

Width
T
Dynamic
C
Speed rating
Static
C0
Mass
Calculation
factors
lbf
Reference Limiting
speed speed
r/min r/min
kg
lb
mm
in
lbf
1.6535
1.8504
2.0472
15
15
16
0.5906
0.5906
0.6299
24 200
27 000
36 500
5 440
6 070
8 200
27 000
32 500
38 000
6 100
7 400
8 600
12 000 16 000
11 000 14 000
10 000 13 000
0.10
0.11
0.15
0.30
0.30
0.40
0.37 1.60
0.43 1.40
0.43 1.40
55
58
62
2.1654
2.2835
2.4409
17
17
18
0.6693
0.6693
0.7087
35 800
36 900
49 000
8 050
8 300
11 010
44 000
46 500
54 000
9 900
10 500
12 200
9 000 12 000
8 500 11 000
8 500 11 000
0.17
0.19
0.22
0.40
0.50
0.50
0.43 1.40
0.46 1.30
0.46 1.30
1.5748
1.7717
1.9685
68
75
80
2.6772
2.9528
3.1496
19
20
20
0.7480
0.7874
0.7874
52 800
58 300
60 500
11 870
13 110
13 600
71 000
80 000
88 000
16 000
18 000
19 800
7 000
6 300
6 000
9 500
8 500
8 000
0.27
0.34
0.37
0.60
0.80
0.90
0.37 1.60
0.40 1.50
0.43 1.40
50
60
65
1.9685
2.3622
2.5591
90
95
100
3.5433
3.7402
3.9370
23
23
23
0.9055
0.9055
0.9055
80 900
95 000
96 500
18 190
21 350
21 690
116 000
122 000
127 000
26 100
27 500
28 600
5 300
5 300
5 000
7 000
6 700
6 000
0.55
0.59
0.63
1.30
1.40
1.40
0.31 1.90
0.43 1.40
0.46 1.30
32014 X
32015 X
32016 X
70
75
80
2.7559
2.9528
3.1496
110
115
125
4.3307
4.5276
4.9213
25
25
29
0.9843
0.9843
1.1417
101 000
106 000
138 000
22 700
23 830
31 020
153 000
163 000
216 000
34 400
36 700
48 600
4 300
4 000
3 600
5 600
5 300
5 000
0.84
0.90
1.30
1.90
2.00
2.90
0.43 1.40
0.46 1.30
0.43 1.40
32017 X
32018 X
32019 X
85
90
95
3.3465
3.5433
3.7402
130
140
145
5.1181
5.5118
5.7087
29
32
32
1.1417
1.2598
1.2598
140 000
168 000
168 000
31 470
37 760
37 760
224 000
270 000
270 000
50 400
60 700
60 700
3 400
3 200
3 200
4 800
4 300
4 300
1.35
1.75
1.80
3.00
3.90
4.00
0.44 1.35
0.43 1.40
0.44 1.35
32020 X
32021 X
32022 X
100
105
110
3.9370
4.1339
4.3307
150
160
170
5.9055
6.2992
6.6929
32
35
38
1.2598
1.3780
1.4961
172 000
201 000
233 000
38 660
45 180
52 370
280 000
335 000
390 000
63 000
75 400
87 700
3 000
2 800
2 600
4 000
3 800
3 600
1.90
2.40
3.05
4.20
5.30
6.80
0.46 1.30
0.44 1.35
0.43 1.40
32024 X
32026 X
32028 X
120
130
140
4.7244
5.1181
5.5118
180
200
210
7.0866
7.8740
8.2677
38
45
45
1.4961
1.7717
1.7717
242 000
314 000
330 000
54 400
70 580
74 180
415 000
540 000
585 000
93 300
121 400
131 600
2 400
2 200
2 200
3 400
3 000
2 800
3.25
4.95
5.25
7.20
11.00
11.60
0.46 1.30
0.43 1.40
0.46 1.30
32030 X
32032 X
32034 X
150
160
170
5.9055
6.2992
6.6929
225
240
260
8.8583
9.4488
10.2362
48
51
57
1.8898
2.0079
2.2441
369 000
82 950
429 000
96 430
512 000 115 100
655 000
780 000
915 000
147 300
175 400
205 700
2 000
1 800
1 700
2 600
2 400
2 200
6.35
7.75
10.50
14.00
17.10
23.20
0.46 1.30
0.46 1.30
0.44 1.35
32036 X
32038 X
32040 X
180
190
200
7.0866
7.4803
7.8740
280
290
310
11.0236
11.4173
12.2047
64
64
70
2.5197
2.5197
2.7559
644 000 144 800 1 160 000

660 000 148 400 1 200 000
748 000 168 200 1 370 000
260 800
269 800
308 000
1 600
1 500
1 400
2 200
2 000
1 900
14.50
15.00
19.50
32.00
33.10
43.00
0.43 1.40
0.44 1.35
0.43 1.40
219

Single row
Series: 32044 X 32064 X
Size: 220 mm 320 mm
8.6614 in 12.5984 in
Series: 32205 B 32230
Size: 25 mm 150 mm
0.9843 in 5.9055 in
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
T
Dynamic
C
mm
in
Speed rating
Static
C0
lbf
lbf
Reference Limiting
speed speed
r/min r/min
mm
in
32044 X
32048 X
32052 X
220
240
260
8.6614
9.4488
10.2362
340
360
400
13.3858
14.1732
15.7480
76.00
76.00
87.00
2.9921
2.9921
3.4252
897 000
935 000
1 170 000
201 600
210 100
263 000
1 660 000
1 800 000
2 200 000
373 200
404 700
494 600
1 300
1 200
1 100
32056 X
32064 X
280
320
11.0236
12.5984
420
480
16.5354 87.00
18.8976 100.00
3.4252
3.9370
1 210 000
1 540 000
272 000
346 200
2 360 000
3 100 000
530 600
696 900
1 000
850
32205 B
322/28 B
32206
25
28
30
0.9843
1.1024
1.1811
52
58
62
2.0472
2.2835
2.4409
19.25
20.25
21.25
0.7579
0.7972
0.8366
35 800
41 800
50 100
8 100
9 400
11 300
44 000
50 000
57 000
32206 B
32207
32207 B
30
35
35
1.1811
1.3780
1.3780
62
72
72
2.4409
2.8346
2.8346
21.25
24.25
24.25
0.8366
0.9547
0.9547
49 500
66 000
60 500
11 100
14 800
13 600
32208
32209
32210
40
45
50
1.5748
1.7717
1.9685
80
85
90
3.1496
3.3465
3.5433
24.75
24.75
24.75
0.9744
0.9744
0.9744
78 800
91 500
82 500
32211
32212
32213
50
60
65
1.9685
2.3622
2.5591
100
110
120
3.9370
4.3307
4.7244
26.75
29.75
32.75
1.0531
1.1713
1.2894
32214
32215
32216
70
75
80
2.7559
2.9528
3.1496
125
130
140
4.9213
5.1181
5.5118
33.25
33.25
35.25
32217
32218
32219
85
90
95
3.3465
3.5433
3.7402
150
160
170
5.9055
6.2992
6.6929
32220
32221
32222
100
105
110
3.9370
4.1339
4.3307
180
190
200
32224
32226
32228
120
130
140
4.7244
5.1181
5.5118
32230
150
5.9055
Mass
Calculation
factors
kg
lb
1 700
1 600
1 400
25.50
27.50
40.00
56.30
60.70
88.20
0.43 1.40
0.46 1.30
0.43 1.40
1 300
1 100
40.50
64.00
89.30
141.10
0.46 1.30
0.46 1.30
9 900
11 300
12 900
9 500 13 000
8 500 12 000
8 500 11 000
0.19
0.25
0.28
0.50
0.60
0.70
0.57 1.05
0.57 1.05
0.37 1.60
58 500
78 000
75 000
13 200
17 600
16 900
8 000 11 000
7 000 9 500
7 000 9 500
0.30
0.43
0.44
0.70
1.00
1.00
0.57 1.05
0.37 1.60
0.57 1.05
17 700
20 600
18 500
86 500
98 000
100 000
19 500
22 100
22 500
6 300
6 300
5 600
8 500
8 000
7 500
0.53
0.58
0.61
1.20
1.30
1.40
0.37 1.60
0.40 1.50
0.43 1.40
106 000
125 000
151 000
23 800
28 100
33 900
129 000
160 000
193 000
29 000
36 000
43 400
5 000
4 500
4 000
6 700
6 000
5 600
0.83
1.15
1.50
1.85
2.60
3.40
0.57 1.05
0.40 1.50
0.40 1.50
1.3091
1.3091
1.3878
157 000
161 000
187 000
35 200
36 100
42 000
208 000
212 000
245 000
46 800
47 700
55 100
3 800
3 600
3 400
5 300
5 000
4 500
1.60
1.70
2.05
3.60
3.80
4.60
0.43 1.40
0.43 1.40
0.43 1.40
38.50
42.50
45.50
1.5157
1.6732
1.7913
212 000
251 000
281 000
47 600
56 400
63 100
285 000
340 000
390 000
64 100
76 500
87 700
3 200
3 000
2 800
4 300
4 000
3 800
2.60
3.35
4.05
5.80
7.40
9.00
0.43 1.40
0.43 1.40
0.43 1.40
7.0866
7.4803
7.8740
49.00
53.00
56.00
1.9291
2.0866
2.2047
319 000
358 000
402 000
71 700
80 400
90 300
440 000
510 000
570 000
99 000
114 700
128 200
2 600
2 600
2 400
3 600
3 400
3 200
4.90
6.00
7.10
10.90
13.30
15.70
0.43 1.40
0.43 1.40
0.43 1.40
215
230
250
8.4646
9.0551
9.8425
61.50
67.75
71.75
2.4213
2.6673
2.8248
468 000
550 000
644 000
105 200
123 600
144 700
695 000
830 000
1 000 000
156 300
186 600
224 800
2 200
2 000
1 900
3 000
2 800
2 600
9.15
11.50
14.50
20.17
25.40
32.00
0.43 1.40
0.43 1.40
0.43 1.40
270
10.6299
77.00
3.0315
737 000
165 600
1 140 000
256 300
1 700
2 400
17.50
38.60
0.43 1.40
220
Single row
Series: 32232 32260
Size: 160 mm 300 mm
6.2992 in 11.8110 in
Series: 32303 32316 B
Size: 17 mm 80 mm
0.6693 in 3.1496 in
Designation
Bore
d
Basic load ratings
Outside diameter
D
mm
in
Width
T
Dynamic
C
mm
in
mm
in
32232
32234
32236
160
170
180
6.2992
6.6929
7.0866
290
310
320
11.4173
12.2047
12.5984
84.00
91.00
91.00
3.3071
3.5827
3.5827
32240
32244
32248
200
220
240
7.8740
8.6614
9.4488
360
400
440
14.1732
15.7480
17.3228
104.00
114.00
127.00
32252
32260
260
300
10.2362
11.8110
480
540
18.8976
21.2599
32303
32304
32305
17
20
25
0.6693
0.7874
0.9843
47
52
62
32306
32307
32307 B
30
35
35
1.1811
1.3780
1.3780
32308
32309
32309 B
40
45
45
32310
32310 B
32311
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Calculation
factors
lbf
lb
880 000
1 010 000
1 010 000
197 800
227 000
227 000
1 400 000
1 630 000
1 630 000
314 800
366 500
366 500
1 600
1 500
1 400
2 200
2 000
1 900
25.50
28.50
29.50
56.30
62.90
65.10
0.43
0.43
0.46
1.40
1.40
1.30
4.0945
4.4882
5 0000
1 210 000
1 610 000
1 940 000
272 000
361 900
436 100
2 000 000
2 700 000
3 350 000
449 600
607 000
753 100
1 300
1 100
1 000
1 700
1 500
1 400
42.50
60.00
81.50
93.70
132.30
179.70
0.40
0.43
0.43
1.50
1.40
1.40
137.00
149.00
5.3937
5.8661
2 200 000
2 750 000
494 500
618 200
3 650 000
4 750 000
820 600
1 067 800
900
800
1 200
1 100
105.00
140.00
231.50
308.70
0.43
0.43
1.40
1.40
1.8504
2.0472
2.4409
20.25
22.25
25.25
0.7972
0.8760
0.9941
34 700
44 000
60 500
7 800
9 890
13 600
33 500
45 500
63 000
7 600
10 300
14 200
11 000 16 000
10 000 14 000
8 000 12 000
0.17
0.23
0.36
0.40
0.60
0.80
0.28
0.30
0.30
2.10
2.00
2.00
72
80
80
2.8346
3.1496
3.1496
28.75
32.75
32.75
1.1319
1.2894
1.2894
76 500
95 200
93 500
17 200
21 400
21 000
85 000
106 000
114 000
19 200
23 900
25 700
7 000 10 000
6 700 9 000
6 300 8 500
0.55
0.73
0.80
1.30
1.70
1.80
0.31
0.31
0.54
1.90
1.90
1.10
1.5748
1.7717
1.7717
90
100
100
3.5433
3.9370
3.9370
35.25
38.25
38.25
1.3878
1.5059
1.5059
117 000
140 000
134 000
26 300
31 400
30 100
140 000
170 000
176 000
31 500
38 300
39 600
5 300
4 800
4 800
8 000
7 000
6 700
1.00
1.35
1.45
2.30
3.00
3.20
0.35
0.35
0.54
1.70
1.70
1.10
50
50
55
1.9685
1.9685
2.1654
110
110
120
4.3307
4.3307
4.7244
42.25
42.25
45.50
1.6634
1.6634
1.7913
172 000
183 000
198 000
38 600
41 100
44 500
212 000
216 000
250 000
47 700
48 600
56 200
4 300
4 500
4 000
6 300
6 000
5 600
1.80
1.85
2.30
4.00
4.10
5.10
0.35
0.54
0.83
1.70
1.10
0.72
32311 B
32312
32312 B
55
60
60
2.1654
2.3622
2.3622
120
130
130
4.7244
5.1181
5.1181
45.50
48.50
48.50
1.7913
1.9094
1.9094
216 000
229 000
220 000
48 500
51 400
49 500
260 000
290 000
305 000
58 500
65 200
68 600
4 300
3 600
3 600
5 600
5 300
5 000
2.50
2.85
2.80
5.60
6.30
6.20
0.35
0.83
0.35
1.70
0.72
1.70
32313
32313 B
32314
65
65
70
2.5591
2.5591
2.7559
140
140
150
5.5118
5.5118
5.9055
51.00
51.00
54.00
2.0079
2.0079
2.1260
264 000
246 000
297 000
59 300
55 300
66 700
335 000
345 000
380 000
75 400
77 600
85 500
3 400
3 200
3 200
4 800
4 800
4 500
3.45
3.35
4.30
7.70
7.40
9.50
0.35
0.54
0.35
1.70
1.10
1.70
32314 B
32315
32315 B
70
75
75
2.7559
2.9528
2.9528
150
160
160
5.9055
6.2992
6.2992
54.00
58.00
58.00
2.1260
2.2835
2.2835
281 000
336 000
336 000
63 200
75 500
75 500
400 000
440 000
475 000
90 000
99 000
106 800
3 000
3 000
2 800
4 300
4 300
4 000
4.25
5.20
5.55
9.40
11.50
12.30
0.54
0.35
0.54
1.10
1.70
1.10
32316
32316 B
80
80
3.1496
3.1496
170
170
6.6929
6.6929
61.50
61.50
2.4213
2.4213
380 000
358 000
85 400
80 500
500 000
520 000
112 400
116 900
3 000
2 800
4 300
4 300
6.20
5.70
13.70
12.60
0.35
0.54
1.70
1.10
221

Single row
Standard
Series: 32317 32324
Size: 85 mm 120 mm
3.3465 in 4.7244 in
Series: 32915 32960
Size: 75 mm 300 mm
2.9528 in 11.8110 in
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings

Width
T
mm
in
85
85
90
3.3465
3.3465
3.5433
180
180
190
7.0866 63.50
7.0866 63.50
7.4803 67.50
2.5000
2.5000
2.6575
32319
32320
32321
95
100
105
3.7402
3.9370
4.1339
200
215
225
7.8740 71.50
8.4646 77.50
8.8583 81.50
32322
32324
110
120
4.3307
4.7244
240
260
32915
32920
32924
75
100
120
2.9528
3.9370
4.7244
32926
32928
32934
130
140
170
32936
32938
32940
32948
32956
32960
32317
32317 B
32318
mm
Dynamic
C
in
Speed rating
Static
C0
lbf
Reference Limiting
speed speed
r/min r/min
Mass
kg
Calculation
factors
lbf
lb
402 000
90 300
391 000
87 800
457 000 102 700
530 000
560 000
610 000
119 200
125 900
137 200
2 800
2 800
2 600
4 000
4 000
4 000
6.85
7.50
8.40
15.20
16.60
18.60
0.35 1.70
0.54 1.10
0.35 1.70
2.8150
3.0512
3.2087
501 000 112 600

572 000 128 500
605 000 136 000
670 000
780 000
815 000
150 700
175 400
183 300
2 400
2 200
2 000
3 400
3 000
3 000
11.00
12.50
14.50
24.30
27.60
32.00
0.35 1.70
0.35 1.70
0.35 1.70
9.4488 84.50
10.2362 90.50
3.3268
3.5630
627 000 140 900

830 000
792 000 178 000 1 120 000
186 600
251 800
1 900
1 800
2 800
2 600
17.00
21.50
37.50
47.40
0.35 1.70
0.35 1.70
105
140
165
4.1339 20.00
5.5118 25.00
6.4961 29.00
0.7874
0.9843
1.1417
70 400
119 000
165 000
15 800
26 700
37 000
116 000
204000
305 000
26 100
45 900
68 600
4 300
3 200
2 600
6 300
4 800
3 800
0.52
1.15
1.80
1.20
2.60
4.00
0.33 1.80
0.33 1.80
0.35 1.70
5.1181
5.5118
6.6929
180
190
230
7.0866 32.00
7.4803 32.00
9.0551 38.00
1.2598
1.2598
1.4961
198 000
205 000
286 000
44 500
46 000
64 200
365 000
390 000
585 000
82 100
87 700
131 600
2 400
2 200
1 900
3 600
3 400
2 800
2.40
2.55
4.50
5.30
5.70
10.00
0.33 1.80
0.35 1.70
0.37 1.60
180
190
200
7.0866
7.4803
7.8740
250
260
280
9.8425 45.00
10.2362 45.00
11.0236 51.00
1.7717
1.7717
2.0079
352 000
79 100
358 000
80 400
473 000 106 300
735 000
765 000
950 000
165 300
172 000
213 600
1 700
1 600
1 500
2 600
2 400
2 200
6.65
7.00
9.50
14.70
15.50
21.00
0.48 1.25
0.48 1.25
0.40 1.50
240
280
300
9.4488
11.0236
11.8110
320
380
420
12.5984 51.00
14.9606 63.50
16.5354 76.00
2.0079
512 000 115 000 1 080 000
2.5000
765 000 171 900 1 660 000
2.9921 1 050 000 236 000 2 240 000
242 800
373 200
503 600
1 300
1 100
950
1 900
1 600
1 400
11.00
20.00
32.00
24.50
44.10
70.60
0.46 1.30
0.43 1.40
0.40 1.50
222
Single row
Series: 33010 33030
Size: 50 mm 150 mm
1.9685 in 5.9055 in
Series: 33108 33122
Size: 40 mm 110 mm
1.5748 in 4.3307 in
Designation
Bore
d
Outside diameter
D
mm
in
mm
in
33010
33011
33012
50
50
60
1.9685
1.9685
2.3622
80
90
95
33013
33014
33015
65
70
75
2.5591
2.7559
2.9528
33016
33017
33018
80
85
90
33019
33020
33021
Basic load ratings

Width
T
Dynamic
C
Speed rating
Static
C0
Mass
Calculation
factors
Reference Limiting
speed
speed
r/min
r/min
kg
lb
mm
in
lbf
lbf
3.1496
3.5433
3.7402
22
27
27
0.9449
1.0630
1.0630
69 300
104 000
106 000
15 600
23 300
23 800
102 000
137 000
143 000
23 000
30 800
32 200
6 000
5 600
5 300
8 000
7 000
6 700
0.45
0.67
0.71
1.00
1.50
1.60
0.31 0.72
0.37 1.60
0.40 1.50
100
110
115
3.9370
4.3307
4.5276
27
31
31
1.0630
1.2205
1.2205
110 000
130 000
134 000
24 700
29 200
30 100
153 000
196 000
228 000
34 400
44 100
51 300
5 000
4 300
4 000
6 300
5 600
5 300
0.78
1.10
1.15
1.80
2.50
2.60
0.46 1.30
0.28 2.10
0.30 2.00
3.1496
3.3465
3.5433
125
130
140
4.9213
5.1181
5.5118
36
36
39
1.4173
1.4173
1.5354
168 000
183 000
216 000
37 700
41 100
48 500
285 000
310 000
355 000
64 100
69 700
79 900
3 600
3 600
3 200
5 000
4 800
4 500
1.65
1.75
2.20
3.70
3.90
4.90
0.28 2.10
0.30 2.00
0.27 2.20
95
100
105
3.7402
3.9370
4.1339
145
150
160
5.7087
5.9055
6.2992
39
39
43
1.5354
1.5354
1.6929
220 000
224 000
246 000
49 400
50 300
55 300
375 000
390 000
430 000
84 300
87 700
96 700
3 200
3 000
2 800
4 300
4 000
3 800
2.30
2.40
3.05
5.10
5.30
6.80
0.28 2.10
0.28 2.10
0.28 2.10
33022
33024
33030
110
120
150
4.3307
4.7244
5.9055
170
180
225
6.6929
7.0866
8.8583
47
48
59
1.8504
1.8898
2.3228
281 000
63 100
292 000
65 600
457 000 102 700
500 000
540 000
865 000
112 400
121 400
194 500
2 600
2 600
2 000
3 600
3 400
2 600
3.85
4.20
8.15
8.50
9.30
18.00
0.28 2.10
0.30 2.00
0.37 1.60
33108
33109
33110
40
45
50
1.5748
1.7717
1.9685
75
80
85
2.9528
3.1496
3.3465
26
26
26
1.0236
1.0236
1.0236
79 200
96 500
85 800
17 800
21 600
19 300
104 000
114 000
122 000
23 400
25 700
27 500
6 000
6 700
5 600
9 000
8 000
7 500
0.51
0.56
0.59
1.20
1.30
1.40
0.35 1.70
0.37 1.60
0.40 1.50
33111
33112
33113
50
60
65
1.9685
2.3622
2.5591
95
100
110
3.7402
3.9370
4.3307
30
30
34
1.1811
1.1811
1.3386
110 000
117 000
142 000
24 700
26 300
31 900
156 000
170 000
208 000
35 100
38 300
46 800
5 000
4 800
4 300
6 700
6 300
5 600
0.86
0.92
1.30
1.90
2.10
2.90
0.40 1.50
0.33 1.80
0.40 1.50
33114
33115
33116
70
75
80
2.7559
2.9528
3.1496
120
125
130
4.7244
4.9213
5.1181
37
37
37
1.4567
1.4567
1.4567
172 000
176 000
179 000
38 600
39 500
40 200
250 000
265 000
280 000
56 200
59 600
63 000
4 000
3 800
3 600
5 300
5 000
4 800
1.70
1.80
1.90
3.80
4.00
4.20
0.37 1.60
0.40 1.50
0.43 1.40
33117
33118
33122
85
90
110
3.3465
3.5433
4.3307
140
150
180
5.5118
5.9055
7.0866
41
45
56
1.6142
1.7717
2.2047
220 000
251 000
369 000
49 400
56 400
82 900
340 000
390 000
630 000
76 500
87 700
141 700
3 400
3 000
2 600
4 500
4 300
3 400
2.45
3.10
5.55
5.50
6.90
12.30
0.40 1.50
0.40 1.50
0.43 1.40
223

Single row
Series: 33205 33220
Size: 25 mm 100 mm
0.9843 in 3.9370 in
Designation
Bore
d
Outside diameter
D
mm
in
Basic load ratings
in
lbf
lbf
2.0472
2.4409
2.8346
22
25
28
0.8661
0.9843
1.1024
54 000
64 400
84 200
12 100
14 500
18 900
56 000
76 500
106 000
12 600
17 200
23 900
10 000 13 000
7 500 11 000
6 300 9 500
80
85
90
3.1496
3.3465
3.5433
32
32
32
1.2598
1.2598
1.2598
105 000
108 000
114 000
23 600
24 200
25 600
132 000
143 000
160 000
29 700
32 200
36 000
5 600
5 300
5 000
8 500
7 500
7 000
0.77
0.85
0.90
1.70
1.90
2.00
0.35 1.70
0.40 1.50
0.40 1.50
2.1654
2.3622
2.5591
100
110
120
3.9370
4.3307
4.7244
35
38
41
1.3780
1.4961
1.6142
138 000
168 000
194 000
31 000
37 700
43 600
190 000
236 000
270 000
42 800
53 100
60 700
4 500
4 000
3 800
6 300
6 000
5 300
1.20
1.60
2.05
2.70
3.60
4.60
0.40 1.50
0.40 1.50
0.40 1.50
70
75
80
2.7559
2.9528
3.1496
125
130
140
4.9213
5.1181
5.5118
41
41
46
1.6142
1.6142
1.8110
201 000
209 000
251 000
45 100
46 900
56 400
285 000
300 000
375 000
64 100
67 500
84 300
3 600
3 400
3 200
5 000
4 800
4 500
2.10
2.25
2.90
4.70
5.00
6.40
0.40 1.50
0.43 1.40
0.43 1.40
85
100
3.3465
3.9370
150
180
5.9055
7.0866
49
63
1.9291
2.4803
286 000
429 000
64 200
96 400
430 000
655 000
96 700
147 300
3 000
2 400
4 300
3 600
3.70
6.95
8.20
15.40
0.43 1.40
0.40 1.50
33205
33206
33207
25
30
35
0.9843
1.1811
1.3780
52
62
72
33208
33209
33210
40
45
50
1.5748
1.7717
1.9685
33211
33212
33213
55
60
65
33214
33215
33216
33217
33220
Static
C0
Calculation
factors
mm
in
Dynamic
C
Mass
Reference Limiting
speed speed
r/min r/min
mm
Width
T
Speed rating
kg
lb
0.23
0.37
0.56
0.60
0.90
1.30
0.35 1.70
0.35 1.70
0.35 1.70
224
Single row
Standard
Series: T2ED 045 T2EE 240
Size: 45 mm 240 mm
1.7717 in 9.4488 in
Designation
Bore
d
Outside diameter
D
mm
in
mm
in
T2ED 045
T7FC 045
T2ED 050
45
45
50
1.7717
1.7717
1.9685
95
95
100
T7FC 050
T2ED 055
T7FC 055
50
55
55
1.9685
2.1654
2.1654
T2EE 060
T7FC 060
T7FC 065
60
60
65
T2ED 070
T7FC 070
T7FC 075
Basic load ratings

Width
T
Dynamic
C
Speed rating
Static
C0
Reference Limiting
speed speed
r/min r/min
mm
in
lbf
lbf
3.7402
3.7402
3.9370
36
29
36
1.4173
1.1417
1.4173
147 000
89 700
154 000
33 000
20 200
34 600
186 000
112 000
200 000
41 900
25 200
45 000
5 300
4 800
5 000
105
110
115
4.1339
4.3307
4.5276
32
39
34
1.2598
1.5354
1.3386
108 000
179 000
125 000
24 300
40 200
28 100
137 000
232 000
163 000
30 800
52 200
36 700
2.3622
2.3622
2.5591
115
125
130
4.5276
4.9213
5.1181
40
37
37
1.5748
1.4567
1.4567
194 000
154 000
157 000
43 600
34 600
35 300
260 000
204 000
216 000
70
70
75
2.7559
2.7559
2.9528
130
140
150
5.1181
5.5118
5.9055
43
39
42
1.6929
1.5354
1.6535
233 000
176 000
201 000
52 300
39 600
45 200
T7FC 080
T4CB 100
T2EE 100
80
100
100
3.1496
3.9370
3.9370
160
145
165
6.2992
5.7087
6.4961
45
24
47
1.7717
0.9449
1.8504
229 000
125 000
314 000
T4CB 120
T4CB 140
T4DB 150
120
140
150
4.7244
5.5118
5.9055
170
195
210
6.6929
7.6772
8.2677
27
29
32
1.0630
1.1417
1.2598
T4DB 160
T4DB 170
T4DB 200
160
170
200
6.2992
6.6929
7.8740
220
230
270
8.6614
9.0511
10.6299
32
32
37
T2DC 220
T4EB 240
T2EE 240
220
240
240
8.6614
9.4488
9.4488
285
320
320
11.2205
12.5984
12.5984
41
42
57
Mass
Calculation
factors
kg
lb
8 000
7 000
7 500
1.20
0.92
1.30
2.70
2.10
2.90
0.33 1.80
0.88 0.68
0.35 1.70
4 300
4 500
4 000
6 300
6 700
5 600
1.20
1.70
1.60
2.70
3.80
3.60
0.88 0.68
0.40 1.50
0.35 1.07
58 500
45 900
48 600
4 300
3 600
3 400
6 300
5 300
5 000
1.85
2.05
2.20
4.10
4.60
4.90
0.54 1.10
0.33 1.80
0.88 0.68
325 000
240 000
280 000
73 100
54 000
63 000
3 800
3 200
3 000
5 600
4 500
4 300
2.45
2.65
3.25
5.50
5.90
7.20
0.33 1.80
0.88 0.68
0.88 0.68
51 500
28 100
70 500
315 000
190 000
480 000
70 900
42 800
108 000
2 800
3 200
2 800
4 000
4 500
4 300
3.95
1.15
3.90
8.80
2.60
8.60
0.88 0.68
0.48 1.25
0.31 1.90
157 000
194 000
233 000
35 200
43 600
52 300
250 000
325 000
390 000
56 200
73 100
87 700
2 600
2 200
2 000
3 800
3 200
3 000
1.70
2.40
3.05
3.80
5.30
6.80
0.48 1.25
0.50 1.20
0.46 1.30
1.2598
1.2598
1.4567
242 000
251 000
330 000
54 400
56 400
74 100
415 000
440 000
600 000
93 300
99 000
134 900
2 000
1 900
1 600
2 800
2 800
2 400
3.25
3.45
5.45
7.20
7.70
12.10
0.48 1.25
0.46 1.30
0.48 1.25
1.6142
1.6535
2.2440
396 000
89 000
830 000
429 000
96 400
815 000
616 000 138 400 1 320 000
186 600
183 300
296 800
1 500
1 300
1 300
2 200
1 900
1 900
6.45
8.45
12.50
14.30
18.70
27.60
0.31 1.90
0.46 1.30
0.35 1.70
225

Paired single row
Standard
Series: 30218/DF 30230/DF
Size: 90 mm 150 mm
3.5433 in 5.9055 in
Series: 31305/DF 31330 X/DF
Size: 25 mm 150 mm
0.9843 in 5.9055 in
Designation
Bore
d
mm
in
Outside diameter
D
mm
in
Basic load ratings

Width
T
mm
in
Dynamic
C
N
lbf
Speed rating
Static
C0
lbf
Reference Limiting
speed
speed
r/min r/min
Mass
kg
Calculation
factors
lb
Y1
Y2
30218/DF
30220/DF
30222/DF
90
100
110
3.5433
3.9370
4.3307
160
180
200
6.2992
7.0866
7.8740
65
74
82
2.5591
2.9134
3.2284
336 000
75 500
418 000
94 000
523 000 117 600
490 000
640 000
800 000
110 200
143 900
179 800
2 400
2 200
2 000
4 000
3 600
3 200
5.15
7.60
10.50
11.40 0.43
16.80 0.43
23.10 0.43
1.6 2.30
1.6 2.30
1.6 2.30
30224/DF
30226/DF
30228/DF
120
130
140
4.7244
5.1181
5.5118
215
230
250
8.4646
87
9.0551 47.5
9.8425 91.5
3.4252
1.8701
3.6024
583 000 131 100

627 000 140 900
721 000 162 100
915 000
980 000
1 140 000
205 700
220 300
256 300
1 800
1 700
1 500
3 000
2 800
2 600
13.00
14.50
18.00
28.70 0.43
32.00 0.43
39.70 0.43
1.6 2.30
1.6 2.30
1.6 2.30
30230/DF
150
5.9055
270
98
3.8583
737 000 165 700
1 120 000
251 800
1 400
2 400
22.50
49.60 0.43
1.6 2.30
31305/DF
31306/DF
31307/DF
25
30
35
0.9843
1.1811
1.3780
62
72
80
2.4409 36.5
2.8346 41.5
3.1496 45.5
1.4370
1.6339
1.7913
64 400
80 900
105 000
14 500
18 200
23 600
80 000
100 000
134 000
18 000
22 500
30 100
6 000 11 000
5 300 9 500
4 500 8 500
0.55
0.85
1.10
1.20 0.83 0.81 1.20

1.90 0.83 0.81 1.02
2.40 0.83 0.81 1.20
31308/DF
31309/DF
31310/DF
40
45
50
1.5748
1.7717
1.9685
90
100
110
3.5433 50.5
3.9370 54.5
4.3307 58.5
1.9882
2.1457
2.3031
146 000
180 000
208 000
32 800
40 500
46 800
163 000
204 000
240 000
36 600
45 900
54 000
4 500
4 000
3 600
7 500
6 700
6 000
1.50
2.00
2.60
3.30 0.83 0.81 1.20

4.40 0.83 0.81 1.20
5.70 0.83 0.81 1.20
31311/DF
31312/DF
31313/DF
55
60
65
2.1654
2.3622
2.5591
120
130
140
4.7244
5.1181
5.5118
63
67
72
2.4803
2.6378
2.8346
209 000
246 000
281 000
47 000
55 300
63 200
275 000
335 000
380 000
61 800
75 300
85 400
3 000
2 800
2 600
5 600
5 300
4 800
3.30
4.10
5.05
7.30 0.83 0.81 1.20

9.00 0.83 0.81 1.20
11.10 0.83 0.81 1.20
31314/DF
31315/DF
31316/DF
70
75
80
2.7559
2.9528
3.1496
150
160
170
5.9055
6.2992
6.6929
76
80
85
2.9921
3.1496
3.3465
319 000
358 000
380 000
71 700
80 500
85 400
440 000
490 000
530 000
98 900
110 200
119 100
2 400
2 200
2 200
4 500
4 300
4 000
6.15
7.25
8.75
13.60 0.83 0.81 1.20

16.00 0.83 0.81 1.20
19.30 0.83 0.81 1.20
31317/DF
31318/DF
31319/DF
85
90
95
3.3465
3.5433
3.7402
180
190
200
7.0866
7.4803
7.8740
89
93
99
3.5039
3.6614
3.8976
413 000
92 800
457 000 102 700
501 000 112 600
570 000
630 000
710 000
128 100
141 600
159 600
2 000
1 900
1 800
3 800
3 400
3 400
10.00
11.50
13.00
22.00 0.83 0.81 1.20

25.40 0.83 0.81 1.20
28.70 0.83 0.81 1.20
31320 X/DF
31322 X/DF
31324 X/DF
100
110
120
3.9370
4.3307
4.7244
215
240
260
8.4646
9.4488
10.2362
113
126
136
4.4488
4.9606
5.3543
644 000 144 800

781 000 175 600
935 000 210 200
930 000
1 160 000
1 400 000
209 100
260 800
314 700
1 700
1 500
1 400
3 000
2 800
2 400
18.00
26.00
38.50
39.70 0.83 0.81 1.20

57.30 0.83 0.81 1.20
84.90 0.83 0.81 1.20
31326 X/DF
31328 X/DF
31330 X/DF
130
140
150
5.1181
5.5118
5.9055
280
300
320
11.0236
11.8110
12.5984
144
154
164
5.6693 1 050 000 236 000

6.0630 1 190 000 267 500
6.4567 1 340 000 301 200
1 560 000
1 800 000
2 040 000
350 700
404 600
458 600
1 300
1 200
1 100
2 400
2 200
2 000
40.00
88.20 0.83 0.81 1.20
52.50 115.70 0.83 0.81 1.20
58.50 129.00 0.83 0.81 1.20
10.6299
226
Paired single row

Series: 32014 X/DF 32064 X/DF
Size: 70 mm 320 mm
2.7559 in 12.5984 in
Designation
Basic load ratings
Bore
d
mm
in
Outside diameter
D
mm
in
Width
T
mm
in
Dynamic
C
N
lbf
32014 X/DF
32017 X/DF
32018 X/DF
70
85
90
2.7559
3.3465
3.5433
110
130
140
4.3307
5.1181
5.5118
50
58
64
1.9685
2.2835
2.5197
200 000
238 000
292 000
32020 X/DF
32022 X/DF
32024 X/DF
100
110
120
3.9370
4.3307
4.7244
150
170
180
5.9055
6.6929
7.0866
64
76
76
2.5197
2.9921
2.9921
292 000
402 000
418 000
32026 X/DF
32028 X/DF
32030 X/DF
130
140
150
5.1181
5.5118
5.9055
200
210
225
7.8740
8.2677
8.8583
90
90
96
3.5433
3.5433
3.7795
32032 X/DF
32034 X/DF
32036 X/DF
160
170
180
6.2992
6.6929
7.0866
240
260
280
9.4488
10.2362
8.6614
32038 X/DF
32040 X/DF
32044 X/DF
190
200
220
7.4803
7.8740
8.6614
290
310
340
32048 X/DF
32056 X/DF
32064 X/DF
240
280
320
9.4488
11.0236
12.5984
360
420
480
Speed rating
Static
C0
Mass
Calculation
factors
Reference Limiting
speed
speed
r/min r/min
kg
lb
lbf
Y1
Y2
45 000
53 500
65 600
305 000
450 000
540 000
68 600
101 200
121 400
3 800
2 800
2 600
5 600
4 800
4 300
1.80
2.80
3.65
4.00 0.43 1.60 2.30

6.20 0.44 1.50 2.30
8.00 0.43 1.60 2.30
65 600
90 400
94 000
560 000
780 000
830 000
125 900
175 300
186 600
2 400
2 200
2 000
4 000
3 600
3 400
3.95
6.30
6.75
8.70 0.46 1.50 2.20

13.90 0.43 1.60 2.30
14.90 0.46 1.50 2.20
539 000 121 200 1 080 000

561 000 126 100 1 160 000
644 000 144 800 1 320 000
242 800
260 800
296 700
1 800
1 700
1 600
3 000
2 800
2 600
10.00
11.00
13.50
22.00 0.43 1.60 2.30

24.30 0.46 1.50 2.20
29.80 0.46 1.50 2.20
102
114
128
4.0157
737 000 165 700 1 560 000
4.4882
880 000 197 800 1 830 000
5.0394 1 100 000 247 300 2 320 000
350 700
411 400
521 500
1 500
1 400
1 300
2 400
2 200
2 000
16.00
22.00
29.50
35.30 0.46 1.50 2.20

48.50 0.44 1.50 2.30
65.00 0.43 1.60 2.30
11.4173
12.2047
13.3858
128
140
152
5.0394 1 120 000 251 800 2 400 000

5.5118 1 280 000 287 700 2 750 000
5.9843 1 540 000 346 200 3 350 000
539 500
618 200
753 100
1 200
1 100
1 000
2 000
1 900
1 700
30.50 67.20 0.44 1.50 2.30

39.00 86.00 0.43 1.60 2.30
51.00 112.40 0.43 1.60 2.30
14.1732
16.5354
18.8976
152
174
200
5.9843 1 570 000 352 900 3 550 000

798 000
6.8504 2 050 000 460 800 4 750 000 1 067 800
7.8740 2 640 000 593 500 6 200 000 1 393 800
950
800
700
1 600 54.50 120.20 0.46 1.50 2.20

1 300 84.50 186.30 0.46 1.50 2.20
1 100 125.00 275.60 0.46 1.50 2.20
227

Paired single row
Standard
Series: 32216/DF 32252/DF
Size: 80 mm 260 mm
3.1496 in 10.2362 in
Designation
Basic load ratings
Bore
d
mm
in
Outside diameter
D
mm
in
Width
T
mm
in
Dynamic
C
N
lbf
32216/DF
32217/DF
32218/DF
80
85
90
3.1496
3.3465
3.5433
140
150
160
5.5118
5.9055
6.2992
70.5
77
85
2.7756
3.0315
3.3465
319 000
369 000
429 000
32219/DF
32220/DF
32222/DF
95
100
110
3.7402
3.9370
4.3307
170
180
200
6.6929
7.0866
7.8740
91
98
112
3.5827
3.8583
4.4094
32224/DF
32226/DF
32228/DF
120
130
140
4.7244
5.1181
5.5118
215
230
250
8.4646
123
9.0551 135.5
9.8425 143.5
32230/DF
32232/DF
32234/DF
150
160
170
5.9055
6.2992
6.6929
270
290
310
10.6299
11.4173
12.2047
154
168
182
32236/DF
32244/DF
32248/DF
180
220
240
7.0866
8.6614
9.4488
320
400
440
12.5984
15.7480
17.3228
32252/DF
260
10.2362
480
18.8976
Speed rating
Static
C0
Mass
Reference Limiting
speed
speed
r/min r/min
kg
Calculation
factors
lbf
490 000
570 000
680 000
110 200
128 100
152 900
2 800
2 600
2 400
4 500
4 300
4 000
4.25
5.45
6.90
9.40 0.43 1.60 2.30

12.00 0.43 1.60 2.30
15.20 0.43 1.60 2.30
484 000
539 000
682 000
108 800 780 000

121 200 880 000
153 300 1 140 000
175 300
197 800
256 300
2 200
2 200
1 900
3 800
3 600
3 200
8.45
10.00
14.50
18.60 0.43 1.60 2.30

22.00 0.43 1.60 2.30
32.00 0.43 1.60 2.30
4.8425
792 000
5.3346
952 000
5.6496 1 100 000
178 000 1 400 000

214 000 1 660 000
247 300 2 000 000
314 700
373 200
449 600
1 800
1 600
1 500
3 000
2 800
2 600
18.50
23.00
29.50
40.80 0.43 1.60 2.30

50.70 0.43 1.60 2.30
65.00 0.43 1.60 2.30
6.0630 1 250 000

6.6142 1 510 000
7.1654 1 720 000
281 000 2 280 000

339 400 2 800 000
386 700 3 250 000
512 500
629 400
730 600
1 400
1 300
1 200
2 400
2 200
2 000
37.00 81.60 0.43 1.60 2.30

48.00 105.80 0.43 1.60 2.30
59.00 130.10 0.43 1.60 2.30
182 7.1654 1 720 000

228 8.9764 2 750 000
254 10.0000 3 300 000
386 700 3 250 000

730 600
618 200 5 400 000 1 214 000
741 800 6 550 000 1 472 400
1 100
900
800
1 900 61.00 134.50 0.46 1.50 2.20

1 600 120.00 264.60 0.43 1.60 2.30
1 500 159.20 351.00 0.43 1.60 2.30
274 10.7874 3 740 000
840 800 7 350 000 1 652 300
750
1 300 221.90 489.20 0.43 1.60 2.30
71 700
83 000
96 400
lb
228
Y1
Y2
Ball bearing units

2716
Nomenclature
SY H
WF W
3
2
1. Housing style:
4
2. Shaft size:
Flange, three-bolt, four-bolt pressed steel
FT
Flange, two-bolt, pressed steel
FY
Flange, four-bolt, cast iron
3. Bearing code:
FYM
Flange, four-bolt, cast iron, medium duty
FM
Narrow width, eccentric lock, M-seal, YET series bearing
FYT
Flange, two-bolt, cast iron
TF
Wide width, set screw lock, M-seal and flinger,

YAR series bearing
FYTM
Flange, two-bolt, cast iron, medium duty
WF
Cartridge, rubber mounted, spherical O.D.
Wide width, eccentric lock, M-seal and flinger,

YEL series bearing
Cartridge, rubber mounted, cylindrical O.D
RM
Narrow width, set screw lock, M-seal, YAT series bearing
Pillow block, pressed steel
TR
Wide width, set screw lock, standard duty,

multi-function seal, YAR series bearing
SR
Pillow block, pressed steel, rubber insert
PF
Wide width, ConCentra lock
SY
Pillow block, cast iron
SYH
Pillow block, cast iron, low center height
SYM
Pillow block, cast iron, medium duty
SYT
Pillow block, low base
TU
Take-up, cast iron
TUM
Take-up, cast iron, medium duty
4. Suffix:
W
Nonrelubricatable housing
No locking collar / No set screws
/AH
Air handling unit (see page 282)
/VA228
High-temperature bearings with graphite technology
/VA201
High-temperature bearings with graphite paste
233
Ball bearing units

Introduction
Grade #10 balls, ground and

honed raceways for precision,
quiet running and higher speed
capacity
Molded glass fiber reinforced

polyamide cage for durability
and quiet running
Prelubricated with a high

quality, long life
lithium/calcium grease
Sphered housing bore mates

with sphered O.D. of bearing,
allows unit to accommodate for
initial errors in alignment
Slotted bolt holes allow for a

range of base bolt spacings and
provide for adjustment at
installation
120 set screw angle for
minimum inner distortion and
knurled cup point set screws for
increased vibration resistance
Housing base is recessed to

accommodate uneven mounting
surfaces
Wide inner ring lengths for

better load distribution
Ball bearing units
234
Introduction
Inner ring length

The bearings for Ball bearing units are available
in wide and narrow width inner ring designs.
When space permits, the wide inner ring is the
preferred choice. Shaft misalignment relative to
the bearing bore is minimized with the wide
inner ring and since the load is distributed over
a greater shaft area. The narrow inner ring is
used when space is limited.
M-seal
The M-seal is standard on FM series housed units
and YET series bearings. This low friction, grease
purgeable contact seal is made up of a wear
resistant elastomer lip bonded to a steel trash
guard. The lip rides on the precision ground
surface of the inner ring providing positive
exclusion of dust, moisture and other
contaminants.
Shaft locking methods

Set screw locking features two set screw 120
apart. This placement of the set screws
maximizes holding power while minimizing inner
ring distortion. Other factors such as: zone
hardening of the bearing inner ring, drilling and
tapping after heat treat, proper screw length, a
knurled cup point set screw and a forged set
screw socket have been incorporated to further
enhance holding power and vibration resistance
(backout).
2F seal
The 2F seal is standard on TF and WF series
housed units and YAR and YEL series bearings.
It consists of the basic M-seal and a flinger
mounted outboard. The flinger provides extra
protection of the contact element and serves to
fling dirt and debris away from the seal opening.
This seal has tested extremely effective in a
variety of contamination conditions including
agricultural applications and very dirty
environments.
Eccentric self-locking features a machined

collar and bearing inner ring which act as
mating cams when assembled on the shaft.
When the collar is engaged on the bearing inner
ring, and turned in the direction of shaft
rotation, it grips the shaft firmly with a binding
action that further increases with rotation. The
single set screw in the collar firmly secures the
position of the eccentric collar. This locking
method is recommended for all applications
except where reversing shaft rotation is involved.
Multi-function seal (2RF)

The Multi-function seal is optional on TF and WF
series housed units and YAR and YEL series
bearings. It is the most effective seal ever
produced for ball bearing units and wide inner
ring bearings. It combines the proven sealing of
the M-seal with an additional flinger-contact seal
assembly. This sealing arrangement provides four
separate barriers against the ingress of
contamination: a flinger, a contact seal, a grease
chamber, and a second contact seal.
Interference (press) fit is sometimes

recommended for eccentric and set screw
locking but it is the required mounting method
for 1726(00) series bearings. 1726(00) series
bearings are designed to be press fit onto the
shaft and have no auxiliary locking device.
ConCentra locking features SKFs patented
mechanical connector that applies a near 360
concentric grip around the entire circumference of
the shaft. Two paired rings with precision
engineered serrations on their contact surfaces
respond to axial displacement by expanding
radially against the shaft. When the mounting
screws are tightened the slotted ring grips the
shaft firmly at the same time assuring the
bearing maintains proper internal clearance
conforming to SKF recommendations. An Allen
wrench with a built in torque indicator, included
with every unit, quickly shows when the proper
locking torque (66 in lbf) has been achieved.
2RS1 seal
The 2RS1 seal is standard on 17262(00) and
17263(00) series bearings. This is the same
contact seal used on SKF deep groove ball
bearings. It is optimized for low friction, wear
resistance, and contaminant exclusion.
Seals
235
Ball bearing units

Product descriptions
Ball bearing units

Ball bearing units consist of a precision wide
inner ring bearing assembled into a housing
made of cast iron, pressed steel or rubber. Units
are prelubricated and are designed to slip fit on
to the shaft. Locking method is either eccentric
self-locking or set screw locking.
On cast iron and pressed steel units, the
outside diameter of the bearing and the inside
diameter of the housing are sphered, allowing
the bearing to swivel within the housing to
accommodate initial alignment.
There are numerous bearing and housing
combinations to accommodate a diversity of
mounting surfaces, load requirements, shaft
sizes and dimensional requirements. Housing
types include: pillow blocks, flange units, take-up
units, flangette units and rubber cartridges.
Bearings include the YAR, YEL and YET series
of wide inner ring bearings.
236
SY & SYH/SYM
FY/FYM
SY & SYHstandard duty, SYMmedium duty

cast iron pillow blocks
FYstandard duty, FYMmedium duty

four-bolt cast iron flange units
Pillow block housings, the most popular housing

design for mounted bearings, are available in
several series. All are designed to support loads
primarily directed through the base. The SY
series housing has a standard base-to-center
height. SYH features a low center height with a
base-to-center height typically 1/16" lower than
the SY series. SYMmedium duty housings
accommodate a larger bearing for a given shaft
size, resulting in a greater load carrying capacity.
All three housings series are supplied with a
grease fitting for relubrication, have slotted
bolt holes for adjustments during installation
and provide for initial bearing alignment. For
more detailed information see data tables on
page 244.
Four-bolt flange units are designed to support

shafts through walls, bulkheads and other flat
surfaces. The housing mounts flush to the
surface and the load is carried by the four
mounting bolts. FYMmedium duty housings
accommodate a larger bearing for a given shaft
size, resulting in a greater load carrying capacity.
Both series are supplied with a grease fitting for
relubrication and provide for initial bearing
alignment. For more detailed information see
data tables on page 253.
FYT/FYTM
FYTstandard duty, FYTMmedium duty

two-bolt cast iron flange units
These flange units support shafts through walls,
bulkheads and other flat surfaces but are of a
more compact two-bolt design. FYTMmedium
duty housings accommodate a larger bearing for
a given shaft size, resulting in a greater load
carrying capacity. Both series are supplied with a
grease fitting for relubrication and provide for
initial bearing alignment. For more detailed
information see data tables on page 258.
TU/TUM
TU/TUMstandard duty,
TU/TUMmedium duty center pull cast
iron take-up units
These take-up units are typically used in
conjunction with a customer supplied frame for
belt or shaft tensioning in conveyor, elevator and
power transmission applications. A wide slot for
the frame guide is standard. TU/TUMmedium
duty accommodates a larger bearing for a given
shaft size, resulting in a greater load carrying
capacity. Both series are supplied with a grease
fitting for relubrication and provide for initial
bearing alignment. For more detailed
F & FT
F & FTlight duty

two-bolt and three-bolt pressed steel
flange units
F and FT housings are lightweight, low cost
solutions for light duty applications. These
housings are of a heavy gauge two piece
stamped steel construction which allows for
initial bearing alignment. Housings are zinc
oxided for corrosion resistance and are nonrelubricatable. The F is a three-bolt design and
the FT is a two-bolt design. For more detailed
S & SR
S & SRlight duty

pressed steel pillow blocks
S and SR housings are lightweight, low cost
solutions for light duty applications. Housings
are of a heavy gauge two piece stamped steel
construction, which allows for initial bearing
alignment. The SR series is of the same design
as the S series but has a conductive rubber liner
for noise and vibration reduction. Housings are
zinc oxided for corrosion resistance and are
nonrelubricatable. For more detailed information
see data tables on page 267.
G&R
G & Rlight duty

rubber cartridges
Rubber cartridges are generally used in heating,
ventilating and air conditioning applications or
other applications where low noise is important.
The conductive rubber cartridge, or tire, helps
dampen noise and vibration as well as dissipate
the build up of static electricity. The G series has
a spherical outside diameter and the R series has
a cylindrical outside diameter. For more detailed
237
Ball bearing units

Wide inner ring bearings

SKF wide inner bearings are based on the
design of the 62(00) series deep groove ball
bearing. They share the same materials, high
precision and high quality manufacturing
processes. Rings and steel balls are made of
SAE 52100 bearing steel. Raceways are
hardened, ground, and honed. Steel balls are a
high precision grade #10. Cages are a molded,
glass fiber reinforced polyamide. The standard
seal is a positive contact, land riding M-seal with
an integral trash guard. Bearings are
prelubricated with an optimum fill of a long life
lithium complex grease and are relubricatable.
The result is a bearing with high speed
capabilities, low noise, superior protection
against contamination, strength, durability, and
one that is easy to install and maintain.
Bearings only differ in the type of locking
method, inner ring length and seal options.
Wide inner ring bearings are offered with
spherical or cylindrical profiled outer rings.
Bearings with a spherical profiled outer ring are
typically used with SKF housings. The sphered
O.D. of the bearing is matched to the sphered
I.D. of the housing allowing the bearing to swivel
and accommodate initial alignment. Bearings
with cylindrical profiled outer rings are
assembled into customer machined housings
and are not designed to accommodate initial
alignment.
YAR-2F
YEL-2F
YAR-2Fstandard duty and medium duty

wide inner ring, set screw locking,
spherical O.D.
YEL-2Fstandard duty
wide inner ring, eccentric locking collar,
spherical O.D.
YAR wide inner ring bearings are offered in

standard duty and medium duty series. The
medium duty series uses a larger bearing for a
given shaft size, resulting in a greater load
carrying capacity. Both series feature an
outboard flinger in addition to the standard
M-seal. As the inner of the bearing rotates, the
flinger flings away moisture and large
contaminates for additional sealing performance.
The wide inner ring offers additional bearing
load support and minimizes shaft misalignment
associated with narrow inner bearings. Housing
units with this bearing have a TF suffix. Options
include a non-relubricatable version, a version
with a grease groove in the outer ring and
SKFs multi-function seal. YAR standard duty
wide inner ring bearings are available in shaft
sizes from 1/2" to 215/16". YAR medium duty wide
inner ring bearings are available in shaft sizes
from 17/16" to 3". For more detailed information
see data tables on page 278.
YEL wide inner ring bearings feature an

outboard flinger in addition to the standard
M-seal. As the inner of the bearing rotates, the
flinger flings away moisture and large
contaminates for additional sealing performance.
The wide inner ring offers additional bearing
load support and minimizes shaft misalignment
associated with narrow inner bearings. Housing
units with this bearing have a WF suffix. Options
include a non-relubricatable version, a version
with a grease groove in the outer ring and SKFs
multi-function seal. YEL wide inner ring bearings
are available in shaft sizes from 3/4" to 27/16".
For more detailed information see data tables
on page 276.
1726
Standard inner ring, press fit,
spherical O.D.
1726
238
1726 series bearings are available in a 62(00)

and 63(00) series. Each has the same
dimensions and seal as the respective SKF
62(00)-2RS1 and 63(00)-2RS1 series deep
groove ball bearing but with a spherical profiled
outer ring. These bearings are designed to be
press fit onto metric sized shafting and provide
higher running accuracy than wide inner ring
bearings. The sphered outer ring allows the
bearing to align within a housing having a
matching spherical surface. These bearings are
typically lubricated for life with a long life lithium
complex grease. 17262(00)-2RS1 series
bearings are available in shaft sizes from 15 to
65 mm 17263(00)-2RS1 series bearings are
available in shaft sizes from 25 to 50 mm. For
page 281.
YEL-2FCW
YET
YET-CW
YEL-2FCWstandard duty
wide inner ring, eccentric locking collar,
cylindrical O.D.
YETstandard duty
narrow inner ring, eccentric locking
collar, spherical O.D.
YET-CWstandard duty
narrow inner ring, eccentric locking collar,
cylindrical O.D.
YEL-2FCW wide inner ring bearings have the

same dimensions and features as the YEL
bearing described above but with a cylindrical
profiled outer ring and a flinger (2F). These
bearings are not designed to accommodate
initial alignment and are lubricated for life
with a long life lithium / calcium complex grease.
YEL-2FCW wide inner ring bearings are
available in shaft sizes from 3/4" to 27/16". For
page 277.
YET narrow inner ring bearings feature a

positive contact, land riding M-seal with an
integral trash guard. This seal is grease
purgeable and provides high speed, low friction
operation along with positive contaminant
exclusion. The narrow inner ring makes the
bearing suitable for use in tight operating
spaces. Housing units with this bearing have an
FM suffix. Options include a non-relubricatable
version and a version with a grease groove in
the outer ring. YET bearings are available in
shaft sizes from 1/2" to 23/16". For more detailed
YET-CW narrow inner ring bearings have the same

dimensions and features as the YET bearing
described previously but with a cylindrical profiled
outer ring. These bearings are not designed to
accommodate initial alignment and are lubricated for
life with a long life lithium/calcium complex grease.
YET-CW narrow inner ring bearings are available
in shaft sizes from 1/2" to 23/16". For more detailed
YSP-2F/AH
wide inner ring, ConCentra locking,
spherical O.D.
YSP-2F/AH
YSP-2F/AH wide inner ring bearings feature an

outboard flinger in addition to the land riding
M-seal and SKFs revolutionary ConCentra
locking system. Utilizing a built-in mechanical
connector that applies a nearly 360 concentric
grip around the shaft, SKF ConCentra inserts
provide superb bearing performance while still
allowing for easy mounting and dismounting.
Providing true concentric locking, ConCentra
locking technology reduces vibration and fretting
corrosion increasing service life and reducing the
shaft damage common to conventional set
screw locking devices when replacement is
necessary. YSP-2F/AH series bearings are the
standard insert in SKF PF/AH air handling
housed units and are available in shaft sizes
from 1" to 115/16".
YAT
YATstandard duty and medium duty

narrow inner ring, set screw locking
YAT narrow inner ring bearings feature a
positive contact, and a land riding M-seal
with an integral trash guard. This seal is grease
purgeable and provides high speed, low friction
operation along with positive contaminant exclusion. The narrow inner ring makes the bearing
suitable for use in tight operating spaces.
Housing units equipped with this bearing have
an RM suffix. Options include a nonrelubricatable version, a version with a grease groove in
the outer ring as well as an air handling
(/AH suffix) unit. YAT bearings are available in
shaft sizes from 1/2" to 215/16" and are offered
with several housing styles. For more detailed
239
Ball bearing units

Bearing selection
Ball bearing units

Radial loads standard series
This table may be used to select series
SY and SYH pillow blocks, FY and FYT
flanged units, and TU take-up units.
Determine the operating speed and life required.
Then select a unit having a bearing radial load
rating equal to or greater than the actual radial
load.
The loads listed in this table are calculated to

give the indicated lives (hours at speed) and are
in accordance with ANSI/ABMA standard 9
load ratings and fatigue life for ball bearings.
A life adjustment factor (a23) of 1.0 has been
used throughout.
These loads are for horizontally mounted shafts

with the radial load directed downward toward
the base of the pillow block.
When the load is heavy, C / P <6.6, a press
fit must be used. In the table, this is the area
shaded in white.
Table 1
Bearing radial load in pounds for given speed and life standard duty
Nominal shaft
diameter
mm
in
Life
12.70
15.88
1/2
5/8
19.05
3/4
20.64
22.22
23.81
25.40
13/16
7/8
15/16
1
26.99
28.58
30.16
31.75
1
1
1
1
1/16
1/8
3/16
1/4
31.75
33.34
34.92
36.51
1
1
1
1
1/4
5/16
3/8
7/16
38.10
1 1/2
41.28
42.86
44.45
1 5/8
1 11/16
1 3/4
49.21
1 15/16
50.80
55.56
2
2 3/16
57.15
61.91
2 1/4
2 7/16
63.50
68.26
2 1/2
2 11/16
69.85
74.61
2 3/4
2 15/16
87.31
3 7/16
100.01
101.60
3 15/16
4
240
Speed RPM
hrs
50
100
200
500
1 000
1 800
3 000
3 600
5 000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
872
692
549
405
321
1,160
920
731
538
427
1,277
1,014
805
593
471
1,780
1,413
1,121
826
656
2,327
1,847
1,466
1,080
857
2,802
2,224
1,765
1,301
1,032
3,029
2,404
1,908
1,406
1,116
3,203
2,542
2,018
1,487
1,180
3,978
3,157
2,506
1,846
1,465
4,825
3,830
3,040
2,240
1,778
5,231
4,152
3,295
2,428
1,927
6,042
4,795
3,806
2,804
2,226
8,677
6,887
5,466
4,028
3,197
11,272
8,947
7,101
5,232
4,153
692
549
436
321
255
920
731
580
427
339
1,014
805
639
471
373
1,413
1,121
890
656
520
1,847
1,466
1,164
857
681
2,224
1,765
1,401
1,032
819
2,404
1,908
1,514
1,116
886
2,542
2,018
1,602
1,180
937
3,157
2,506
1,989
1,465
1,163
3,830
3,040
2,413
1,778
1,411
4,152
3,295
2,615
1,927
1,529
4,795
3,806
3,021
2,226
1,767
6,887
5,466
4,339
3,197
2,537
8,947
7,101
5,636
4,153
3,296
549
436
346
255
202
731
580
460
339
269
805
639
507
373
296
1,121
890
706
520
413
1,466
1,164
924
681
540
1,765
1,401
1,112
819
650
1,908
1,514
1,202
886
703
2,018
1,602
1,271
937
743
2,506
1,989
1,579
1,163
923
3,040
2,413
1,915
1,411
1,120
3,295
2,615
2,076
1,529
1,214
3,806
3,021
2,398
1,767
1,402
5,466
4,339
3,444
2,537
2,014
7,101
5,636
4,473
3,296
2,616
405
321
255
188
149
538
427
339
250
198
593
471
373
275
218
826
656
520
384
304
1,080
857
681
501
398
1,301
1,032
819
604
479
1,406
1,116
886
653
518
1,487
1,180
937
690
548
1,846
1,465
1,163
857
680
2,240
1,778
1,411
1,040
825
2,428
1,927
1,529
1,127
894
2,804
2,226
1,767
1,302
1,033
4,028
3,197
2,537
1,869
1,484
5,232
4,153
3,296
2,429
1,928
321
255
202
149
118
427
339
269
198
157
471
373
296
218
173
656
520
413
304
242
857
681
540
398
316
1,032
819
650
479
380
1,116
886
703
518
411
1,180
937
743
548
435
1,465
1,163
923
680
540
1,778
1,411
1,120
825
655
1,927
1,529
1,214
894
710
2,226
1,767
1,402
1,033
820
3,197
2,537
2,014
1,484
1,178
4,153
3,296
2,616
1,928
1,530
264
210
166
123
97
351
279
221
163
129
387
307
244
180
143
539
428
340
250
199
705
559
444
327
260
849
673
535
394
313
917
728
578
426
338
970
770
611
450
357
1,205
956
759
559
444
1,461
1,160
921
678
538
1,584
1,257
998
735
584
1,830
1,452
1,153
849
674
2,628
2,086
1,656
1,220
968
3,414
2,710
2,151
1,585
1,258
223
177
140
103
82
296
235
187
137
109
326
259
206
151
120
455
361
286
211
168
595
472
375
276
219
716
568
451
332
264
774
614
487
359
285
818
649
515
380
301
1,016
806
640
472
374
1,233
978
776
572
454
1,336
1,060
842
620
492
1,543
1,225
972
716
569
210
166
132
97
77
279
221
176
129
103
307
244
193
143
113
428
340
270
199
158
559
444
352
260
206
673
535
424
313
248
728
578
459
338
268
770
611
485
357
284
956
759
602
444
352
1,160
921
731
538
427
1,257
998
792
584
463
188
149
118
87
69
250
198
157
116
92
275
218
173
128
101
384
304
242
178
141
501
398
316
233
185
604
479
380
280
222
653
518
411
303
240
Bearing selection
Ball bearing units

Radial loads medium series
This table may be used to select series
SYM pillow blocks, FYM and FYTM
flanged units, and TUM take-up units.
Determine the operating speed and life required.
Then select a unit having a bearing radial load
rating equal to or greater than the actual radial
load.
The loads listed in this table are calculated to

give the indicated lives (hours at speed) and are
in accordance with ANSI/ABMA standard 9
load ratings and fatigue life for ball bearings.
A life adjustment factor (a23) of 1.0 has been
used throughout.
These loads are for horizontally mounted shafts

with the radial load directed downward toward
the base of the pillow block.
When the load is heavy, C / P 6.6, a press fit
must be used. In the table this is the area
shaded in white.
Table 2
Bearing radial load in pounds for given speed and life medium duty
Nominal shaft
diameter
mm
in
36.51
1 7/16
38.10
1 1/2
42.86
44.45
1 11/16
1 3/4
49.21
1 15/16
55.56
2 3/16
61.91
63.50
2 7/16
2 1/2
68.26
2 11/16
74.61
76.20
2 15/16
3
87.31
88.90
3 7/16
3 1/2
Life
Speed RPM
hrs
50
100
200
500
1 000
1 800
3 000
3 600
5 000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
5,000
10,000
20,000
50,000
100,000
2,802
2,224
1,765
1,301
1,032
3,029
2,404
1,908
1,406
1,116
3,203
2,542
2,018
1,487
1,180
3,978
3,157
2,506
1,846
1,465
4,825
3,830
3,040
2,240
1,778
5,677
4,506
3,576
2,635
2,091
6,042
4,795
3,806
2,804
2,226
6,650
5,278
4,189
3,087
2,450
11,272
8,947
7,101
5,232
4,153
2,224
1,765
1,401
1,032
819
2,404
1,908
1,514
1,116
886
2,542
2,018
1,602
1,180
937
3,157
2,506
1,989
1,465
1,163
3,830
3,040
2,413
1,778
1,411
4,506
3,576
2,838
2,091
1,660
4,795
3,806
3,021
2,226
1,767
5,278
4,189
3,325
2,450
1,944
8,947
7,101
5,636
4,153
3,296
1,765
1,401
1,112
819
650
1,908
1,514
1,202
886
703
2,018
1,602
1,271
937
743
2,506
1,989
1,579
1,163
923
3,040
2,413
1,915
1,411
1,120
3,576
2,838
2,253
1,660
1,317
3,806
3,021
2,398
1,767
1,402
4,189
3,325
2,639
1,944
1,543
7,101
5,636
4,473
3,296
2,616
1,301
1,032
819
604
479
1,406
1,116
886
653
518
1,487
1,180
937
690
548
1,846
1,465
1,163
857
680
2,240
1,778
1,411
1,040
825
2,635
2,091
1,660
1,223
971
2,804
2,226
1,767
1,302
1,033
3,087
2,450
1,944
1,433
1,137
5,232
4,153
3,296
2,429
1,928
1,032
819
650
479
380
1,116
886
703
518
411
1,180
937
743
548
435
1,465
1,163
923
680
540
1,778
1,411
1,120
825
655
2,091
1,660
1,317
971
770
2,226
1,767
1,402
1,033
820
2,450
1,944
1,543
1,137
903
4,153
3,296
2,616
1,928
1,530
849
673
535
394
313
917
728
578
426
338
970
770
611
450
357
1,205
956
759
559
444
1,461
1,160
921
678
538
1,719
1,365
1,083
798
633
1,830
1,452
1,153
849
674
2,014
1,598
1,269
935
742
3,414
2,710
2,151
1,585
1,258
716
568
451
332
264
774
614
487
359
285
818
649
515
380
301
1,016
806
640
472
374
1,233
978
776
572
454
1,450
1,151
913
673
534
1,543
1,225
972
716
569
1,699
1,348
1,070
788
626
673
535
424
313
248
728
578
459
338
268
770
611
485
357
284
956
759
602
444
352
1,160
921
731
538
427
604
479
380
280
222
653
518
411
303
240
241
Ball bearing units

Bearing selection
Speed ratings
The speed at which ball bearing units can
operate depends on the means by which they
are located on the shaft and also the type of
seal. For bearings of series YAR, YEL, YET, YAT
and YSP the speeds are limited by the fit on the
shaft; the looser the fit the lower the speed.
Recommended maximum values are given in
Table 3.
Bearings with multi-function seals should not
be operated at speeds in excess of 60% of those
quoted in the table, particularly when shafts
having an h6 tolerance are used.
The speed ratings of bearings of series
17262(00)-2RS1 and 17263(00)-2RS1 are the
same as for standard SKF sealed deep groove
ball bearings. The ratings for these series are
also given in the table.
Table 3
Speed ratings for insert bearings
Basic
bearing
size
Speed ratings for bearings of series:

YAR, YEL, YET, YAT, YSP
with shaft tolerance
h6
h7
h8
h9
17262(00)
h11
rpm
rpm
202
203
204
205
9500
8500
7000
6000
5300
4500
4300
3800
3200
1500
1300
1000
950
850
700
13000
12000
10000
8500
12000
11000
9500
7500
206
207
208
209
6300
5300
4800
4300
4000
3400
3000
2600
2800
2200
1900
1700
900
750
670
600
630
530
480
430
7500
6300
5600
5000
6300
6000
5000
4500
210
211
212
213
4000
3600
3400
3000
2400
2000
1900
1700
1600
1400
1300
1100
560
500
480
430
400
360
340
300
4800
4300
4000
3600
4300
3800
3400
3200
214
215
216
2800
2600
2400
1600
1500
1400
1000
930
900
400
380
360
280
260
240
3400
3200
3000
3000
2800
2600
Internal clearance
SKF inch series YAR, YEL, YET, YAT and YSP
wide inner ring bearings are produced as
standard with internal clearance according to
Table 4. The radial internal clearance of series
17262(00)-2RS1 and 17263(00)-2RS1
correspond to those for Normal radial internal
clearance for deep groove ball bearings and are
indicated in Table 4.
Table 4
Radial internal clearance of wide inner ring bearings

Basic
bearing
size
Radial internal clearance of bearings of series:

YAR, YEL, YET, YAT, YSP
17262(00)
17263(00)
min
max
min
max
0.0001 in
203
204-206
207-208
209-210
211-213
214-216
242
17263(00)
4
5
5
6
7
8
0.0001 in
10
11
13
14
17
20
1
2
2
2

7
8
8
9

Bearing selection
Aligning torque
Misalignment
Cages
The torque required to align an insert bearing in

its housing is a controlled value. Standard
aligning torques are shown in Table 5. Torques
that are too low (due to a loose housing fit) can
result in outer ring spinning. Torques that are
too high can cause excessive moment loads in
the bearing and consequential heat generation
as it tries to accommodate misalignment.
Ball bearing units can compensate for up to 5

of static misalignment. However, in the cast iron
housings when it is desirable to relubricate the
bearings, initial errors in alignment should not
exceed 2 for basic bearings size 211 and
smaller and 1.5 for larger sizes. Misalignment
greater than this will prevent the lubrication
holes in the outer ring of the bearing from lining
up with the groove in the housing bore and the
bearings will not be relubricated.
All wide inner ring bearings are fitted with an

injection molded, heat stabilized, glass fiber
reinforced polyamide 6.6 cage. This material has
a favorable combination of strength and
elasticity and cages of this material have given
excellent performance in a wide variety of
applications. The friction of these cages is low
and they have excellent running properties
under adverse conditions. Additionally, the cages
promote quiet operation. The operating
temperature range for the cage exceeds that of
the grease with which the bearings are filled.
Table 5
Grease fill
Alignment torque
Torque
(in-lbs)
Basic bearing
YAR, YEL, YET
Min
Max
203
204
205
206
207
208
209
210
211
212
213
214
215
216
43
43
43
43
43
43
43
43
43
43
43
43
43
43
87
87
174
174
217
217
217
217
217
217
304
304
304
304
Generally speaking, wide inner ring bearings are

designed to operate without relubrication under
normal speed and operating conditions. All wide
inner ring bearings are sealed at both sides with
rubbing contact seals and are filled with a
special long life grease of NLGI consistency 2.
The grease has good corrosion inhibiting
properties and is suitable for operating
temperatures between 4 F and 248 F.
However, under extreme conditions or in heavily
contaminated environments, it may be
necessary to relubricate the bearings. Reference
the SKF General Catalog (6000EN) for
relubrication intervals.
243
Ball bearing units

Pillow block / standard duty
SY-TF
Cast-iron housing
Standard center height
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: YAS, NP, P2B-SC, VPS200, P3-U200N
How to order
SY 1 TF
Option
Specify
Multi-function seal
Nonrelubricatable
SY 1TR
SY 1 TFW
For bearing information see page 278; for seal speed limits see page 242.
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
(No. reqd)
lb
SY 1/2 TF
SY 5/8 TF
YAR 203-008-2F
2150
13/16
11/4
315/32
43/16
27/32
15
SY 3/4 TF
YAR 204-012-2F
2860
15/16
11/4
315/32
43/16
233/64
13
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
17/16
51/8
113/32
311/16
411/32
23/4
SY 13/16 TF
SY 7/8 TF
SY 15/16 TF
SY 1 TF
11/16
11/8
13/16
11/4
SY 1 1/16 TF
SY 1 1/8 TF
SY 1 3/16 TF
SY 11/4 ATF
YAR
YAR
YAR
YAR
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
11
11/4
15/16
13/8
17/16
SY 11/4 TF
SY 15/16 TF
SY 13/8 TF
SY 17/16 TF
YAR
YAR
YAR
YAR
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
1 /8
11/2
19/16
SY 11/2 TF
SY 19/16 TF
YAR 208-108-2F
YAR 208-109-2F
6910
15/8
111/16
13/4
SY 15/8 TF
SY 111/16 TF
SY 13/4 TF
YAR 209-110-2F
YAR 209-111-2F
YAR 209-112-2F
115/16
SY 115/16 TF
2
23/16
/2
/8
/4
/16
/8
15
/16
7
/16
/16
/8
(2)-3/8
1.1
1.1
23
(2)-3/8
1.4
25
(2)-3/8
1.8
1.8
1.7
1.7
3 /32
/32
/2
/16
1 /16
21
4 /4
6 /16
25
1 /32
11
4 /16
5 /4
21
3 /32
11
115/16
629/32
129/32
415/16
53/4
329/32
7470
21/8
73/8
129/32
13
55/16
YAR 210-115-2F
7900
21/4
21/8
57/8
SY 2 TF
SY 23/16 TF
YAR 211-200-2F
YAR 211-203-2F
9810
21/2
85/8
23/8
15
21/4
27/16
SY 21/4 TF
SY 27/16 TF
YAR 212-204-2F
YAR 212-207-2F
11900
23/4
915/32
23/8
21/2
211/16
SY 21/2 TF
SY 211/16 TF
YAR 213-208-2F
YAR 213-211-2F
12900
101/8
23/4
215/16
SY 23/4 TF
SY 215/16 TF
YAR 215-212-2F
YAR 215-215-2F
14900
31/4
11
1 /16
244
Mass
/32
/8
/8
/32
/32
/8
3.0
2.5
2.5
2.8
(2)- /2
(2)- /2
3.6
3.7
3.6
3.5
13/16
(2)-1/2
4.2
4.3
47/32
13/16
(2)-1/2
5.4
5.2
5.1
61/2
41/2
19/32
(2)-5/8
6.4
63/8
71/8
15/16
(2)-5/8
8.4
7.9
71/16
715/16
51/2
19/16
(2)-5/8
10.6
10.0
29/16
15/32
715/32
81/2
57/8
111/16
(2)-3/4
13.3
13.3
227/32
19/32
617/32
11/16
113/16
(2)-3/4
17.6
16.6
/4
/4
/16
/8
/16
/16
/4
/4
/4
/8

SY-RM
Cast-iron housing
Set screw locking
Narrow inner ring
M-seal
Replaces: SAS, VPS 100, P2B-VSC, P3-S200E
Shaft
dia.
Pillow block
designation
Bearing
designation
in
Bearing
load rating
dynamic
C
Bolts
A
Emin
Emax
lbf
in
in
in
in
in
in
in
in
in
Mass
(No.
reqd)
lbs
2
8
SY 1 2 RM
SY 5 8 RM
YAT 203-008
YAT 203-010
2150
1316
114
9 16
31532
41164
2732
1 4
5 8
(2)-38
1.3
1.1
SY 3 4 RM
YAT 204-012
2860
1516
114
16
31532
4316
23364
32
23
(2)-38
1.3
15
8
16
1
SY 8 RM
SY 15 16 RM
SY 1 RM
YAT 205-014
YAT 205-015
YAT 205-100
3150
1716
518
11332
31116
41132
23 4
25
32
(2)-38
1.6
1.7
1.6
11 8
13 16
11 4
SY 11 8 RM
SY 13 16 RM
SY 11 4 ARM
YAT 206-102
YAT 206-103
YAT 206-104
4390
11116
1916
21
414
3732
23
(2)-12
2.4
2.4
2.3
11 4
13 8
17 16
SY 11 4 RM
SY 13 8 RM
SY 17 16 RM
YAT 207-104
YAT 207-106
YAT 207-107
5740
178
6516
12532
41116
514
32132
(2)-12
3.4
3.3
3.2
11 2
SY 11 2 RM
YAT 208-108
6910
11516
62932
12932
41516
534
32932
29
118
(2)-12
4.0
111 16
13 4
SY 111 16 RM
SY 13 4 RM
YAT 209-111
YAT 209-112
7470
218
738
12932
13 16
5516
4732
7 16
1732
(2)-12
4.9
5.0
115 16
SY 115 16 RM
YAT 210-115
7900
214
218
578
612
412
16
11764 (2)-58
5.9
2
23 16
SY 2 RM
SY 23 16 RM
YAT 211-200
YAT 211-203
9810
212
858
238
15
638
718
1 2
1932
(2)-58
8.3
7.7
21 4
27 16
SY 21 4 RM
SY 27 16 RM
YAT 212-204
YAT 212-207
11900
234
91532
238
234
7116
71516
512
17 32
138
(2)-58
10.4
9.6
215 16
SY 215 16 RM
YAT 215-215
14900
314
11
22732
1932
61732
37
64
11732 (2)-34
16.0
1
5
32
16
16
64
64
32
245
Ball bearing units

SY-WF
Cast-iron housing
Eccentric locking
Wide inner ring
M-seal & flingers
Replaces: RAS, VPE 200, P2B-SXR, P3-Y200N
How to order
SY 1 WF
Option
Specify
Multi-function seal
Nonrelubricatable
SY 1 WR
SY 1 WFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
2860
15/16
SY 3/4 WF
YEL 204-012-2F
13
YEL
YEL
YEL
YEL
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
1 /16
5 /8
1 /32
SY 13/16 WF
SY 7/8 WF
SY 15/16 WF
SY 1 WF
11/16
11/8
13/16
SY 11/16 WF
SY 11/8 WF
SY 13/16 WF
YEL 206-101-2F
YEL 206-102-2F
YEL 206-103-2F
4390
111/16
19/16
11/4
15/16
13/8
17/16
SY 11/4 WF
SY 15/16 WF
SY 13/8 WF
SY 17/16 WF
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
1 /8
11/2
SY 11/2 WF
YEL 208-108-2F
6910
15/8
111/16
13/4
SY 15/8 WF
SY 111/16 WF
SY 13/4 WF
YEL 209-110-2F
YEL 209-111-2F
YEL 209-112-2F
115/16
SY 115/16 WF
2
23/16
/16
/8
15
/16
7
E
Max
(No. reqd)
lb
/4
E
Min
Mass
/16
43/16
11
11
233/64
43
/64
11/32
(2)-3/8
1.5
1 /16
(2)- /8
1.9
1.9
1.9
1.8
(2)-1/2
3.2
3.1
3.0
4 /32
2 /4
21
41/4
37/32
23
/32
13/16
6 /16
25
1 /32
11
4 /16
5 /4
21
3 /32
47
/64
1 /32
(2)- /2
3.9
3.9
3.9
3.8
115/16
629/32
129/32
415/16
53/4
329/32
27
/32
13/8
(2)-1/2
4.7
7470
21/8
73/8
129/32
13
55/16
47/32
27/32
27
/32
(2)-1/2
5.7
5.6
5.7
YEL 210-115-2F
7900
21/4
21/8
/8
57/8
61/2
41/2
31
11/2
(2)-5/8
6.9
SY 2 WF
SY 23/16 WF
YEL 211-200-2F
YEL 211-203-2F
9810
21/2
95/8
23/8
15
/16
63/8
71/8
13/32
123/32
(2)-5/8
9.2
9.4
21/4
27/16
SY 21/4 WF
SY 27/16 WF
YEL 212-204-2F
YEL 212-207-2F
11900
23/4
915/16
21/2
71/16
715/16
51/2
17/32
127/32
(2)-5/8
12.0
11.8
215/16
SY 215/16 WF
YEL 215-215-2F
14900
31/4
11
227/32
19/32
617/32
115/32
25/32
(2)-3/4
17.2
246
315/32
3 /16
13
11
11/4
/8
/32
/4
/4
/16
/16
/32

SY-FM
Cast-iron housing
Eccentric locking
Narrow inner ring
M-seal
Replaces: VAS, VPE100, P2B-SXV, P3-W200U
How to order
SY 1 FM
Option
Specify
Nonrelubricatable
SY 1 FMW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
YET 203-008
YET 203-010
2150
13/16
11/4
/16
315/32
43/16
27/32
SY 3/4 FM
YET 204-012
2860
15/16
11/4
/16
315/32
4316
233/64
19
13
/16
/8
15
/16
1
SY 13/16 FM
SY 7/8 FM
SY 15/16 FM
SY 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
1 /16
13
/8
11
11
11/16
11/8
13/16
11/4
SY 11/16 FM
SY 11/8 FM
SY 13/16 FM
SY 11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
11
1 /16
1 /16
21
11/4
15/16
13/8
17/16
SY 11/4 FM
SY 15/16 FM
SY 13/8 FM
SY 17/16 FM
YET 207-104
YET 207-105
YET 207-106
YET 207-107
5740
17/8
65/16
125/32
11/2
SY 11/2 FM
YET 208-108
6910
115/16
629/32
129/32
15/8
111/16
13/4
SY 15/8 FM
SY 111/16 FM
SY 13/4 FM
YET 209-110
YET 209-111
YET 209-112
7470
21/8
73/8
129/32
13
115/16
SY 115/16 FM
YET 210-115
7900
21/4
21/8
2
23/16
SY 2 FM
SY 23/16 FM
YET 211-200
YET 211-203
9810
21/2
85/8
23/8
15
27/16
SY 27/16 FM
YET 212-207
11847
23/4
915/32
23/8
/4
(No. reqd)
lb
SY 1/2 FM
SY 5/8 FM
/2
/8
Mass
5 /8
1 /32
3 /16
2 /4
19
/64
/64
/8
15
/16
15
/16
(2)-3/8
1.4
1.2
(2)-3/8
1.4
2.5
1.8
1.7
1.7
(2)- /8
1 /32
(2)- /2
2.4
2.5
2.5
2.4
4 /4
3 /32
23
/4
411/16
51/4
321/32
/8
15/32
(2)-1/2
3.5
3.5
3.5
3.6
/4
41516
53/4
329/32
/16
119/64
(2)-1/2
4.5
55/16
47/32
/16
119/64
(2)-1/2
5.3
5.3
5.1
57/8
61/2
41/2
/16
119/64
(2)-5/8
6.4
63/8
71/8
15
/32
17/16
(2)-5/8
8.4
8.0
17/16
715/16
51/2
17
/32
19/16
(2)-5/8
11.3
/32
/16
/8
/16
4 /32
/4
/64
247
Ball bearing units

Pillow block / medium duty
SYM-TF
Cast-iron housing
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: MP, VPS300, P2B-SCM, C-35
How to order
SYM 17/16 TF
Option
Specify
Multi-function seal
Nonrelubricatable
SYM 17/16 TR
SYM 17/16 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
3732
411/16 51/4
321/32
11
13
/16
55/16
4732
129/32
13
/16
55/16
21/8
57/8
21/2
85/8
23/8
15
11900
23/4
915/32 23/8
11
SYM 1 TF
YAR 206-100-2F
4738
111/16
19/16
21
41/4
13/16
SYM 13/16 TF
YAR 207-103-2F
5737
17/8
65/16
125/32
17/16
SYM 17/16 TF
YAR 208-107-2F
6910
21/8
73/8
13/4
11/2
SYM 11/2 TF
YAR 209-108-2F
7470
21/8
73/8
111/16
13/4
SYM 111/16 TF
SYM 13/4 TF
YAR 210-111-2F
YAR 210-112-2F
7900
21/4
115/16
SYM 115/16 TF
YAR 211-115-2F
9810
23/16
SYM 23/16 TF
YAR 212-203-2F
(No. reqd)
lb
E
Max
Mass
15
2.5
(2)-1/2
3.4
13/16
(2)-1/2
5.3
4732
13/16
(2)-1/2
5.7
61/2
41/2
19/32
(2)-5/8
7.0
6.7
63/8
71/8
15/16
(2)-5/8
8.8
71/16
715/16
51/2
19/16
(2)-5/8
11.7
7 /16
15
7 /16
5 /16
1 /16
(2)- /8
10.7
/4
/8
/16
/8
/16
/4
/4
/4
/8
/8
2 /16
SYMH 2 /16 TF
YAR 212-203-2F
11900
2 /16
27/16
21/2
SYM 27/16 TF
SYM 21/2 TF
YAR 214-207-2F
YAR 214-208-2F
14000
1015/64 29/16
117/32
71/2
81/2
61/32
13/16
19/16
(2)-3/4
15.7
15.4
211/16
SYM 211/16 TF
YAR 215-211-2F
14900
31/2
12
155/64
81/2
91/2
617/32
11/16
113/16
(2)-3/4
23.8
215/16
3
SYM 215/16 TF
SYM 3 TF
YAR 216-215-2F
YAR 216-300-2F
16400
31/2
12
31/16
17/8
81/2
91/2
631/32
13/16
17/8
(2)-3/4
22.8
22.4
248
9 /32 2 /8
(2)-1/2
/32

SYH-TF
Cast-iron housing
Low center height
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: YAK, NPL, VPLS200, P2B-SCB, PL3-U200N
How to order
SYH 1 TF
Option
Specify
Multi-function seal
Nonrelubricatable
SYH 1 TR
SYH 1 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
(No. reqd)
lb
SYH 1/2 TF
SYH 5/8 TF
YAR 203-008-2F
YAR 203-010-2F
2150
13/16
11/4
315/32
43/16
23/32
15
SYH 3/4 TF
YAR 204-012-2F
2860
11/4
11/4
315/32
43/16
215/32
13
/16
/8
15
/16
1
SYH 13/16 TF
SYH 7/8 TF
SYH 15/16 TF
SYH 1 TF
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
15/16
51/8
113/32
311/16
411/32
25/8
11/16
11/8
13/16
11/4
SYH
SYH
SYH
SYH
11/16 TF
11/8 TF
13/16 TF
11/4 ATF
YAR
YAR
YAR
YAR
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
19/16
19/16
37
/64
41/4
11/4
15/16
13/8
17/16
SYH
SYH
SYH
SYH
11/4 TF
15/16 TF
13/8 TF
17/16 TF
YAR
YAR
YAR
YAR
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
113/16
65/16
125/32
11
/16
411/16
15/8
111/16
13/4
SYH 15/8 TF
SYH 111/16 TF
SYH 13/4 TF
YAR 209-110-2F
YAR 209-111-2F
YAR 209-112-2F
7470
21/16
73/8
129/32
13
/16
115/16
SYH 115/16 TF
YAR 210-115-2F
7900
23/16
21/8
2
23/16
SYH 2 TF
SYH 23/16 TF
YAR 211-200-2F
YAR 211-203-2F
9810
27/16
85/8
23/8
21/4
27/16
SYH 21/4 TF
SYH 27/16 TF
YAR 212-204-2F
YAR 212-207-2F
11900
211/16
915/32
23/8
23/4
215/16
SYH 23/4 TF
SYH 215/16 TF
YAR 215-212-2F
YAR 215-215-2F
14915
35/16
11
227/32
/2
/8
/4
Mass
(2)-3/8
1.3
1.3
23
(2)-3/8
1.5
25
(2)-3/8
1.8
1.8
1.7
1.7
39/64
(2)-1/2
3.0
2.9
2.9
2.8
51/4
319/32
11
(2)-1/2
3.6
3.5
3.5
3.4
55/16
45/32
13/16
(2)-1/2
5.4
5.3
5.2
27
57/8
61/2
415/32
19/32
(2)-5/8
6.3
29
63/8
71/8
15/16
(2)-5/8
8.5
8.0
71/16
715/16
57/16
19/16
(2)-5/8
10.1
9.5
15/16
69/16
11/16
113/16
(2)-3/4
16.0
/16
/2
/2
/32
/32
/32
/2
/16
/8
/16
/4
/4
/8
/8
/32
/32
/8
249
Ball bearing units

SYH - RM
Cast-iron housing
Low center height
Set screw locking
Narrow inner ring
M-seal
da
Replaces: SAK, VPL, VPLS200,

P2B-VSCB, PL3-S200E
A
D
E Min.
E Max.
B
Shaft
dia.
Pillow block
designation
Bearing
designation
in
1
2
8
Bearing
load rating
dynamic
C
A
lbf
in
Bolts
B
EMin
EMax
Mass
(No.
reqd)
lb
SYH 2 RM
SYH 58 RM
YAT 203-008
YAT 203-010
2150
1316
11/4
9 16
31532
4316
2332
14
58
(2)-3/8
1.3
1.1
SYH 34 RM
YAT 204-012
2860
114
114
31532
4316
21532
32
23
(2)-38
1.3
31116
41132
258
16
25
(2)-38
1.8
1.5
1.6
414
3964
23
(2)-12
2.4
2.3
3.5
16
41116
514
31932
(2)-12
3.5
3.3
3.2
16
5516
4532
16
1732
(2)-12
4.9
4.9
5.0
11764
(2)-58
6.1
32
8
15
16
SYH 8 RM
SYH 1516 RM
SYH 1 RM
YAT 205-014
YAT 205-015
YAT 205-100
3150
1516
518
11332
118
1316
114
SYH 118 RM
SYH 1316 RM
SYH 114 ARM
YAT 206-102
YAT 206-103
YAT 206-104
4390
1916
1916
37
114
138
1716
SYH 114 RM
SYH 138 RM
SYH 1716 RM
YAT 207-104
YAT 207-106
YAT 207-107
5740
11316
6516
12532
11
158
11116
134
SYH 158 RM
SYH 11116 RM
SYH 134 RM
YAT 209-110
YAT 209-111
YAT 209-112
7470
2116
738
12932
13
11516
SYH 11516 RM
YAT 210-115
7900
2316
218
27
32
578
612
41532
2
2316
SYH 2 RM
SYH 2316 RM
YAT 211-200
YAT 211-203
9810
27/16
858
238
29
32
638
718
1932
(2)-58
8.0
7.7
214
2716
SYH 214 RM
SYH 2716 RM
YAT 212-204
YAT 212-207
11900
211/16
91532
238
71/16
715/16
57/16
17 32
138
(2)-58
9.8
9.2
21516
SYH 21516 RM
YAT 215-215
14900
3516
11
22732
1516
6916
16
11732
(2)-34
15.8
250
64
64
16
32

SYH-WF
Cast-iron housing
Low center height
Eccentric locking
Wide inner ring
M-seal & flingers
Replaces: RAK, VPLE200, P2B-SXRB, PL3-Y200N
How to order
SYH 1 WF
Option
Specify
Multi-function seal
Nonrelubricatable
SYH 1 WR
SYH 1 WFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
SYH 3/4 WF
YEL 204-012-2F
2860
11/4
11/4
315/32 4316
215/32
43
13
/16
/8
15
/16
1
SYH 13/16 WF
SYH 7/8 WF
SYH 15/16 WF
SYH 1 WF
YEL
YEL
YEL
YEL
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
1516
518
11332
31116 41132
258
11/16
11/8
13/16
11/4 AWF
SYH
SYH
SYH
SYH
11/16 WF
11/8 WF
13/16 WF
11/4 AWF
YEL
YEL
YEL
YEL
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
1916
1916
37
64
414
11/4
15/16
13/8
17/16
SYH
SYH
SYH
SYH
11/4 WF
15/16 WF
13/8 WF
17/16 WF
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
11316
6516
12532
11
16
15/8
111/16
13/4
SYH 15/8 WF
SYH 111/16 WF
SYH 13/4 WF
YEL 209-110-2F
YEL 209-111-2F
YEL 209-112-2F
7470
2116
738
12932
115/16
SYH 115/16 WF
YEL 210-115-2F
7900
2316
2
23/16
SYH 2 WF
SYH 23/16 WF
YEL 211-200-2F
YEL 211-203-2F
9810
2716
21/4
27/16
SYH 21/4 WF
SYH 27/16 WF
YEL 212-204-2F
YEL 212-207-2F
11900
215/16
SYH 215/16 WF
YEL 215-215-2F
14900
(No. reqd)
lb
/4
Mass
11/32
(2)-3/8
1.4
11
1116
(2)-38
1.9
2.0
2.0
1.7
3964
23
32
1316
(2)-12
3.2
3.2
2.7
2.7
41116 514
31932
47
64
1932
(2)-12
4.1
3.9
4.0
3.7
13
5516
4532
27
32
138
(2)-12
5.9
5.8
5.3
218
27
578
61/2
41532
31
32
11/2
(2)-5/8
6.5
858
238
29
638
718
1332
12332
(2)-58
9.3
8.7
21116
91532
238
7116
71516
512
1732
12732
(2)-58
12.2
10.8
35/16
11
22732 15/16
6916
11532
2532
(2)-34
17.2
/2
16
32
32
/64
16
251
Ball bearing units

SYH-FM
Cast-iron housing
Low center height
Eccentric locking
Narrow inner ring
M-seal
Replaces: VAK, VPL100,
P2B-SXVB, PL3-W200U
How to order
SYH 1 FM
Option
Specify
Nonrelubricatable
SYH 1 FMW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
YET 203-008
YET 203-010
2150
1316
114
16
31532
4316
2332
SYH 3/4 FM
YET 204-012
2860
11/4
11/4
/2
315/32
43/16
215/32
19
/64
13
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
1516
518
11332
31116
41132
258
19
SYH 13/16 FM
SYH 7/8 FM
SYH 15/16 FM
SYH 1 FM
11/16
11/8
13/16
11/4
SYH
SYH
SYH
SYH
11/16 FM
11/8 FM
13/16 FM
11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
1916
1916
37
64
414
3964
23
11/4
15/16
13/8
17/16
SYH
SYH
SYH
SYH
11/4 FM
15/16 FM
13/8 FM
17/16 FM
YET 207-104
YET 207-105
YET 207-106
YET 207-107
5740
11316
6516
12532
11
16
41116
514
31932
15/8
111/16
13/4
SYH 15/8 FM
SYH 111/16 FM
SYH 13/4 FM
YET 209-110
YET 209-111
YET 209-112
7470
21/16
73/8
12932
13
/16
55/16
4532
115/16
SYH 115/16 FM
YET 210-115
7900
23/16
21/8
27
32
578
61/2
2
23/16
SYH 2 FM
SYH 23/16 FM
YET 211-200
YET 211-203
9810
2716
858
238
29
32
638
27/16
SYH 27/16 FM
YET 212-207
11847
211/16
91532
23/8
71/16
/4
/16
/8
15
/16
7
252
(No. reqd)
lb
SYH 1/2 FM
SYH 5/8 FM
/2
/8
Mass
(2)-38
1.1
1.1
19
(2)-3/8
1.3
64
19
(2)-38
1.9
1.9
1.9
1.6
64
1132
(2)-12
3.0
2.4
2.5
3.5
1532
(2)-12
3.5
3.7
3.5
3.5
/16
11964
(2)-1/2
5.5
5.1
5.2
41532
/16
1964
(2)-5/8
6.3
718
15
32
1716
(2)-58
8.8
7.9
715/16
57/16
17
32
19/16
(2)-5/8
11.3
/64
64
Flange / standard duty

FY-TF
Cast-iron flange
Four-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: YCJ, SF, VP45200, F4B-SC, F3-U200N
How to order
FY 1 TF
Option
Specify
Multi-function seal
Nonrelubricatable
FY 1 TR
FY 1 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
FY 12 TF
FY 58 TF
YAR 203-008-2F
YAR 203-010-2F
2150
218
25 64
FY 34 TF
YAR 204-012-2F
2860
338
212
13
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
3 4
2 4
15
FY 1316 TF
FY 78 TF
FY 1516 TF
FY 1 TF
1116
118
1316
114
FY 1116 TF
FY 118 TF
FY 1316 TF
FY 114 ATF
YAR
YAR
YAR
YAR
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
4 4
3 4
33
114
1516
138
1716
FY 114 TF
FY 1516 TF
FY 138 TF
FY 1716 TF
YAR
YAR
YAR
YAR
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
44164 358
33
112
FY 112 TF
YAR 208-108-2F
6910
518
158
11116
134
FY 158 TF
FY 11116 TF
FY 134 TF
YAR 209-110-2F
YAR 209-111-2F
YAR 209-112-2F
7470
11516
FY 11516 TF
YAR 210-115-2F
2
2316
FY 2 TF
FY 2316 TF
214
2716
16
8
15
16
7
(No. reqd)
lb
2
8
Mass
1732
218
37 64
1 8
(4)-38
1.0
1.0
1532
11532
23164
(4)-38
1.3
32
1 16
1 32
2 64
16
(4)- 16
1.9
1.9
2.0
1.7
64
1 32
1 32
3 64
25
32
(4)- 16
2.7
2.5
2.4
2.7
(4)-12
3.2
3.6
3.5
3.0
16
17
21
51
19
32
15364
34764
53
64
35
64
13364
2964
41164
15
16
13
64
(4)-12
4.3
52564 418
35
64
11732
2964
41332
15
16
13
64
(4)-916
4.8
4.8
4.7
7900
558
438
19
32
11116
22564
44164 1764
23
64
(4)-916
5.3
YAR 211-200-2F
YAR 211-203-2F
9810
638
518
178
23564
5932
1732
11
32
(4)-58
7.9
7.5
FY 214 TF
FY 2716 TF
YAR 212-204-2F
YAR 212-207-2F
11900
678
558
43
64
2364
22932
558
11132
11
32
(4)-58
9.6
9.0
212
21116
FY 212 TF
FY 21116 TF
YAR 213-208-2F
YAR 213-211-2F
12900
738
578
21
32
2116
25564
6116
1532
32
(4)-58
11.3
10.9
234
21516
FYF 234 MTF

FYF 21516 MTF
YAR 215-212-2F
YAR 215-215-2F
14900
734
2916
3716
638
158
16
(4)-34
15.7
14.8
64
12364
64
59 64
253
Ball bearing units

E
A square
D
FY-RM
Cast-iron flange
Four-bolt mounting
Set screw locking
Narrow inner ring
M-seal
B square
K
Replaces: SCJ, VF, VF4S-100, F4B-VSC, F3-S200E

Y
da
Shaft
dia.
Pillow block
designation
Bearing
designation
in
1
2
8
5
3
FY 2 RM
FY 58 RM
YAT 203-008
YAT 203-010
YAT 204-012
FY 4 RM
Bearing
load rating
dynamic
C
lbf
in
in
in
in
in
in
in
in
218
25
59
11364
218
37
21
31
15
2150
Bolts
2860
3 8
2 2
64
16
64
15
1 32
1 32
2 64
64
1.7
1.6
1.7
16
(4)-716
2.4
2.3
2.3
(4)-12
3.2
2.9
2.9
(4)-12
4.1
(4)-916
4.5
4.5
4.6
334
234
15
32
1316
13364
25164
118
1316
114
FY 118 RM
FY 1316 RM
FY 114 ARM
YAT 206-103
YAT 206-103
YAT 206-104
4390
414
314
33
64
1932
12132
31964
25
114
138
1716
FY 114 RM
FY 138 RM
FY 1716 RM
YAT 207-104
YAT 207-106
YAT 207-107
5740
44164
358
33
64
12364
15364
34764
53
29
112
FY 112 RM
YAT 208-108
6910
518
35
64
13364
2116
41164
15
1.0
(4)-716
3150
16
16
YAT 205-014
YAT 205-015
YAT 205-100
32
(4)-38
FY 8 RM
FY 1516 RM
FY 1 RM
64
64
lb
1.3
32
(No.
reqd)
(4)- 8
8
15
16
Mass
64
1 8
11116
134
FY 1 8 RM
FY 11116RM
FY 134 RM
YAT 209-110
YAT 209-111
YAT 209-112
7470
52564
35
64
11732
2964
41332
15
33
11516
FY 11516 RM
YAT 210-115
7900
558
438
19
32
11116
22364
44164
1764
43
(4)-916
6.0
2
218
2316
FY 2 RM
FY 218 RM
FY 2316 RM
YAT 211-200
YAT 211-202
YAT 211-203
9810
638
518
178
212
5932
1732
47
(4)-58
7.8
7.7
7.5
214
2716
FY 214 RM
FY 2716 RM
YAT 212-204
YAT 212-207
11900
678
558
43
2364
22332
558
11132
13
(4)-58
9.8
9.2
21516
FYF 21516 RM
YAT 215-215
14900
734
2916
3532
638
158
1364
(4)-34 12.3
254
64
16
64
64
64
16

FY-WF
Cast-iron flange
Four-bolt mounting
Eccentric locking
Wide inner ring
M-seal & flingers
Replaces: RCJ, VF4E-200, F4B-SXR, F3-Y200N
How to order
FY 1 WF
Option
Specify
Multi-function seal
Nonrelubricatable
FY 1 WR
FY 1 WFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
3
Dynamic
capacity
C
Bolts
A
lbf
in
2860
33/8
21/2
Mass
(No. reqd)
lb
FY 3/4 WF
YEL 204-012-2F
15/32
125/32
231/64
/16
/8
15
/16
1
FY 13/16 WF
FY 7/8 WF
FY 15/16 WF
FY 1 WF
YEL
YEL
YEL
YEL
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
3 /4
2 /4
15
/32
1 /16
13
1 /16
51
2 /64
/16
(4)- /16
2.1
2.0
2.0
1.9
11/16
11/8
13/16
11/4
FY 11/16 WF
FY 11/8 WF
FY 13/16 WF
FY 11/4 AWF
YEL
YEL
YEL
YEL
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
41/4
31/4
33
/64
19/32
131/32
319/64
25
/32
/16
(4)-7/16
2.9
2.9
2.5
2.7
11/4
15/16
13/8
17/16
FY 11/4 WF
FY 15/16 WF
FY 13/8 WF
FY 17/16 WF
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
441/64
35/8
33
/64
123/64
23/32
347/64
53
/64
/64
(4)-1/2
3.6
3.6
3.3
3.6
11/2
FY 11/2 WF
YEL 208-108-2F
6910
51/8
35
/64
133/64
29/32
411/64
15
/16
/16
(4)-1/2
4.7
15/8
111/16
13/4
FY 15/8 WF
FY 111/16 WF
FY 13/4 WF
YEL 209-110-2F
YEL 209-111-2F
YEL 209-112-2F
7470
525/64
41/8
35
/64
117/32
29/32
413/32
15
/16
/16
(4)-9/16
5.6
5.0
5.0
115/16
FY 115/16 WF
YEL 210-115-2F
7900
55/8
43/8
19
/32
111/16
217/32
441/64
17/64
/16
(4)-9/16
5.7
2
23/16
FY 2 WF
FY 23/16 WF
YEL 211-200-2F
YEL 211-203-2F
9810
63/8
51/8
17/8
27/8
59/32
17/32
/16
(4)-5/8
8.6
8.0
21/4
27/16
FY 21/4 WF
FY 27/16 WF
YEL 212-204-2F
YEL 212-207-2F
11900
67/8
55/8
43
23/64
31/8
55/8
111/32
/16
(4)-5/8
9.9
9.8
215/16
FY 215/16 MWF
YEL 215-215-2F
14915
73/4
29/16
325/32
63/8
15/8
/32
(4)-3/4
15.2
/4
13
7
/16
/8
/64
/4
/4
/4
/16
(4)-3/8
1.5
255
Ball bearing units

FY-FM
Cast-iron flange
Four-bolt mounting
Eccentric locking
Narrow inner ring
M-seal
Replaces: VCJ, VF4E-100, F4B-SXV, F3-W200U
How to order
FY 1 FM
Option
Specify
Nonrelubricatable
FY 1 FMW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
(No. reqd)
lb
FY 1/2 FM
FY 5/8 FM
YET 203-008
YET 203-010
2150
21/8
25
FY 3/4 FM
YET 204-012
2860
33/8
21/2
13
/16
/8
15
/16
1
FY 13/16 FM
FY 7/8 FM
FY 15/16 FM
FY 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
33/4
23/4
15
11/16
11/8
13/16
11/4
FY 11/16 FM
FY 11/8 FM
FY 13/16 FM
FY 11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
4 /4
11/4
15/16
13/8
17/16
FY 11/4 FM
FY 15/16 FM
FY 13/8 FM
FY 17/16 FM
YET 207-104
YET 207-105
YET 207-106
YET 207-107
5740
11/2
FY 11/2 FM
YET 208-108
15/8
111/16
13/4
FY 15/8 FM
FY 111/16 FM
FY 13/4 FM
115/16
/2
/8
Mass
59
129/64
21/8
37
21
/64
(4)-3/8
1.1
1.1
15/32
143/64
231/64
29
/64
(4)-3/8
1.3
/32
13/16
143/64
251/64
15
/32
(4)-7/16
1.8
1.7
1.7
1.7
3 /4
33
/64
1 /32
27
1 /32
19
3 /64
25
/32
/16
(4)- /16
2.6
2.5
2.4
2.6
441/64
35/8
33
/64
123/64
163/64
347/64
53
/64
/16
(4)-1/2
3.4
3.4
3.1
3.1
6910
51/8
35
/64
133/64
215/64
411/64
15
/16
15
/32
(4)-1/2
4.3
YET 209-110
YET 209-111
YET 209-112
7470
525/64
41/8
35
/64
117/32
215/64
413/32
15
/16
15
/32
(4)-9/16
4.9
4.8
4.6
FY 115/16 FM
YET 210-115
7900
55/8
43/8
19
/32
111/16
225/64
441/64
17/64
19
/32
(4)-9/16
5.3
2
23/16
FY 2 FM
FY 23/16 FM
YET 211-200
YET 211-203
9810
63/8
51/8
17/8
221/32
59/32
17/32
11
/16
(4)-5/8
7.8
7.5
27/16
FY 27/16 FM
YET 212-207
11847
67/8
55/8
43
23/64
23/16
55/8
111/32
13/32
(4)-5/8
9.6
/4
256
/64
/16
/8
/64
/64
/64
/4
/4
Flange / medium duty

FYM-TF
Cast-iron flange
Four-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: MSF, VF4S-300, F4B-SCM, FC4-35
How to order
FYM 1 TF
Option
Specify
Multi-function seal
Nonrelubricatable
FYM 1 TR
FYM 1 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
FYM 1 TF
YAR 206-100-2F
4387
41/4
31/4
33
/64
19/32
121/32
319/64
25
/32
/32
(4)-7/16
2.6
13/16
FYM 13/16 TF
YAR 207-103-2F
5737
441/64
35/8
33
/64
123/64
153/64
347/64
53
/64
/64
(4)-1/2
3.3
17/16
FYM 17/16 TF
YAR 208-107-2F
6910
55/8
21
/32
117/32
29/64
411/64
15
/16
13
/64
(4)-1/2
4.6
11/2
FYM 11/2 TF
YAR 209-108-2F
7470
525/64
41/8
35
/64
117/32
29/64
413/32
15
/16
13
/64
(4)-9/16
5.3
111/16
13/4
FYM 111/16 TF
FYM 13/4 TF
YAR 210-111-2F
YAR 210-112-2F
7900
55/8
43/8
25
/32
13/4
225/64
441/64
17/64
23
/64
(4)-9/16
5.7
5.7
115/16
FYM 115/16 TF
YAR 211-115-2F
9810
63/8
51/8
27
/32
17/8
217/32
59/32
17/32
11
/32
(4)-5/8
8.2
23/16
FYM 23/16 TF
YAR 212-203-2F
11900
67/8
55/8
27
/32
25/32
229/32
55/8
111/32
11
/32
(4)-5/8
9.7
27/16
21/2
FYM 27/16 TF
FYM 21/2 TF
YAR 214-207-2F
YAR 214-208-2F
14200
14000
73/8
57/8
11
/16
21/4
61/8
17/16
/4
(4)-5/8
13.6
13.0
211/16
FYM 211/16 MTF
YAR 215-211-2F
14900
73/4
29/16
37/16
63/8
15/8
/16
(4)-3/4
15.5
215/16
3
FYM 215/16 TF
FYM 3 TF
YAR 216-215-2F
YAR 216-300-2F
16400
73/4
25/16
31/4
63/4
13/8
/16
(4)-3/4
15.7
15.5
/4
/8
257
Ball bearing units

FYT-TF
Cast-iron flange
Two-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: YCJT, SFT, VF2S-200, F2B-SC FX3-U200N
How to order
FYT 1 TF
Option
Specify
Multi-function seal
FYT 1 TR
FYT 1 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
FYT 1/2 TF
FYT 5/8 TF
YAR 203-008-2F
YAR 203-010-2F
2150
37/8
15
15
17/32
21/8
19
/8
(2)-3/8
0.8
0.8
FYT 3/4 TF
YAR 204-012-2F
2860
413/32
317/32
31
19/32
23/8
/16
(2)-3/8
0.9
13
/16
/8
15
/16
1
FYT 13/16 TF
FYT 7/8 TF
FYT 15/16 TF
FYT 1 TF
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
47/8
329/32
15
13/16
117/32
23/4
/16
(2)-7/16
1.4
1.3
1.3
1.3
11/16
11/8
13/16
11/4
FYT 11/16 TF
FYT 11/8 TF
FYT 13/16 TF
FYT 11/4 ATF
YAR
YAR
YAR
YAR
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
5 /16
19
4 /32
/2
1 /32
21
1 /32
3 /4
25
/32
(2)- /16
2.2
2.0
1.9
1.8
11/4
15/16
13/8
17/16
FYT 11/4 TF
FYT 15/16 TF
FYT 13/8 TF
FYT 17/16 TF
YAR
YAR
YAR
YAR
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
65/32
51/8
/2
111/32
113/16
325/32
13
/16
(2)-1/2
2.8
2.8
2.7
2.6
11/2
FYT 11/2 TF
YAR 208-108-2F
6910
63/4
521/32
/16
117/32
29/64
41/32
15
13
(2)-1/2
3.6
15/8
111/16
13/4
FYT 15/8 TF
FYT 111/16 TF
FYT 13/4 TF
YAR 209-110-2F
YAR 209-111-2F
YAR 209-112-2F
7470
71/32
527/32
/16
117/32
29/64
43/8
15
13
/64
(2)-9/16
4.4
4.3
4.2
115/16
FYT 115/16 TF
YAR 210-115-2F
7900
77/16
63/16
19
/32
111/16
225/64
49/16
17/64
23
/64
(2)-9/16
4.7
2
23/16
FYT 2 TF
FYT 23/16 TF
YAR 211-200-2F
YAR 211-203-2F
9810
81/2
71/4
13
/16
17/8
215/32
15/32
(2)-5/8
7.0
6.7
/2
/8
/4
258
/32
/16
/32
/16
/32
/32
/16
/4
/16
/16
/32
/8
/64
/32
FYT-RM
Cast-iron flange
Four-bolt mounting
Set screw locking
Narrow inner ring
M-seal
da
Replaces: SCJT, VFT, VF2S-100, F2B-VSC, FX3-200E
J
D
E
Shaft
dia.
Pillow block
designation
Bearing
designation
in
1
Bearing
load rating
dynamic
C
lbf
Bolts
A
lb
FYT 12 RM
FYT 58 RM
YAT 203-008
YAT 203-010
2150
378
15
15
1732
218
19
FYT 34 RM
YAT 204-012
2860
41332
31732
31
32
1932
238
1316
11732
234
(No.
reqd)
in
2
8
Mass
32
16
16
32
21
64
(2)-38
0.8
(2)-38
0.9
16
29
(2)-716
1.4
1.3
1.2
32
8
15
16
FYT 8 RM
FYT 1516 RM
FYT 1 RM
YAT 205-014
YAT 205-015
YAT 205-100
3150
478
32932
15
118
1316
114
FYT 118 RM
FYT 1316 RM
FYT 114 ARM
YAT 206-102
YAT 206-103
YAT 206-104
4390
5916
41932
1932
12132
314
25
32
(2)-716
1.9
1.8
1.7
114
138
1716
FYT 114 RM
FYT 138 RM
FYT 1716 RM
YAT 207-104
YAT 207-106
YAT 207-107
5740
6532
518
11132
15364
32532
13
16
(2)-12
2.6
2.6
2.2
112
FYT 112 RM
YAT 208-108
6910
634
52132
16
11732
2116
4132
15
16
(2)-12
3.4
16
11732
2964
438
15
16
33
64
(2)-916
4.2
4.1
4.0
32
64
16
16
2
1 8
11116
134
FYT 1 8 RM
FYT 11116 RM
FYT 134 RM
YAT 209-111
YAT 209-111
YAT 209-112
7470
7132
52732
11516
FYT 11516 RM
YAT 210-115
7900
7716
6316
19
32
11116
22364
4916
1764
43
64
(2)-916
4.7
2
2316
FYT 2 RM
FYT 2316 RM
YAT 211-200
YAT 211-203
9810
812
714
13
16
178
2716
1532
21
32
(2)-58
6.7
6.3
259
Ball bearing units

FYT-WF
Cast-iron flange
Two-bolt mounting
Eccentric locking
Wide inner ring
M-seal & flingers
Replaces: RCJT, VF2E-100, F2B-SXR F3-Y200N
How to order
FYT 1 WF
Option
Specify
Multi-function seal
Nonrelubricatable
FYT 1 WR
FY 1 WFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
3
FYT 3/4 WF
YEL 204-012-2F
13
FYT 13/16 WF
FYT 7/8 WF
FYT 15/16 WF
FYT 1 WF
YEL
YEL
YEL
YEL
205-013-2F
205-014-2F
205-015-2F
205-100-2F
11/16
11/8
13/16
FYT 11/16 WF
FYT 11/8 WF
FYT 13/16 WF
11/4
115/16
13/8
17/16
/4
/16
/8
15
/16
7
Dynamic
capacity
C
Bolts
A
lbf
in
2860
413/32
(No. reqd)
lb
317/32
/16
3150
4 /8
29
3 /32
15
YEL 206-101-2F
YEL 206-102-2F
YEL 206-103-2F
4390
59/16
419/32
FYT 11/4 WF
FYT 115/16 WF
FYT 13/8 WF
FYT 17/16 WF
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
65/32
51/8
11/2
FYT 11/2 WF
YEL 208-108-2F
6910
63/4
15/8
111/16
13/4
FYT 15/8 WF
FYT 111/16 WF
FYT 13/4 WF
YEL 209-110-2F
YEL 209-111-2F
YEL 209-112-2F
7470
115/16
FYT 115/16 WF
YEL 210-115-2F
2
23/16
FYT 2 WF
FYT 23/16 WF
YEL 211-200-2F
YEL 211-203-2F
31
/32
139/64
23/8
/16
/16
(2)- /16
1.5
1.5
1.5
2.0
/64
(2)-3/8
1 /16
13
1 /16
2 /4
/2
19/32
131/32
31/4
25
/32
/16
(2)-7/16
2.3
2.2
2.0
/2
111/32
23/32
325/32
13
/16
/32
(2)-1/2
3.3
3.2
3.2
2.8
521/32
/16
117/32
25/16
41/32
15
/64
(2)-1/2
3.8
71/32
527/32
/16
117/32
25/16
43/8
15
/64
(2)-9/16
4.6
4.6
4.4
7900
77/16
63/16
19
/32
111/16
239/64
49/16
17/64
/64
(2)-9/16
5.5
9810
81/2
71/4
13
/16
17/8
27/8
15/32
/16
(2)-5/8
7.1
6.8
/32
/4
/16
/16
1.3
260
Mass

FYT-FM
Cast-iron flange
Two-bolt mounting
Eccentric locking
Narrow inner ring
M-seal
Replaces: VCJT, VF2E-100, F2B-SXV, FX3-W200E
How to order
FYT 1 FM
Option
Specify
Nonrelubricatable
FYT 1 FMW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
FYT 1/2 FM
FYT 5/8 FM
YET 203-008
YET 203-010
2150
37/8
15
15
17/16
21/8
19
21
/64
(2)-3/8
0.9
0.8
FYT 3/4 FM
YET 204-012
2860
413/32
317/32
31
11/2
23/8
17
/64
(2)-3/8
1.0
13
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
47/8
329/32
15
13/16
111/16
23/4
29
/64
(2)-7/16
FYT 13/16 FM
FYT 7/8 FM
FYT 15/16 FM
FYT 1 FM
1.4
1.4
1.4
1.3
11/16
11/8
13/16
11/4
FYT 11/16 FM
FYT 11/8 FM
FYT 13/16 FM
FYT 11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
5 /16
19
4 /32
/2
1 /32
27
1 /32
3 /4
25
/32
(2)- /16
2.1
2.0
2.0
1.8
11/4
115/16
13/8
17/16
FYT 11/4 FM
FYT 115/16 FM
FYT 13/8 FM
FYT 17/16 FM
YET 207-104
YET 207-105
YET 207-106
YET 207-107
5740
65/32
51/8
/2
111/32
131/32
325/32
13
/16
(2)-1/2
3.1
3.0
2.7
2.7
11/2
FYT 11/2 FM
YET 208-108
6910
63/4
521/32
/16
117/32
215/64
41/32
15
33
(2)-1/2
3.6
15/8
111/16
13/4
FYT 15/8 FM
FYT 111/16 FM
FYT 13/4 FM
YET 209-110
YET 209-111
YET 209-112
7470
71/32
527/32
/16
117/32
215/64
43/8
15
33
/64
(2)-9/16
4.6
4.6
4.2
115/16
FYT 115/16 FM
YET 210-115
7900
77/16
63/16
19
/32
111/16
225/64
49/16
17/64
43
/64
(2)-9/16
5.1
2
23/16
FYT 2 FM
FYT 23/16 FM
YET 211-200
YET 211-203
9810
81/2
71/4
13
/16
17/8
219/32
15/32
11
/16
(2)-5/8
6.3
6.1
/2
/8
/4
/16
/8
15
/16
7
/32
/16
/32
/16
/32
/32
/16
/4
/16
/16
/16
/16
/64
261
Ball bearing units

FYTM-TF
Cast-iron flange
Two-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: MSFT, VF2S-300, F2B-SCM FC2-3S
How to order
FYTM 17/16 TF
Option
Specify
Multi-function seal
Nonrelubricatable
FYTM 17/16 TR
FYTM 17/16 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
FYTM 1 TF
YAR 206-100-2F
4390
59/16
419/32
/2
19/32
121/32
31/4
25
/32
/32
(2)-7/16
2.3
13/16
FYTM 13/16 TF
YAR 207-103-2F
5740
65/32
51/8
/2
111/32
113/32
325/32
13
/16
/8
(2)-1/2
2.9
17/16
FYTM 17/16 TF
YAR 208-107-2F
6910
63/4
521/32
/16
117/32
29/64
41/32
15
13
/64
(2)-1/2
3.7
11/2
FYTM 11/2 TF
YAR 209-108-2F
7470
71/32
527/32
/16
117/32
29/64
43/8
15
13
/64
(2)-9/16
5.4
111/16
13/4
FYTM 111/16 TF
FYTM 13/4 TF
YAR 210-111-2F
YAR 210-112-2F
7900
77/16
63/16
19
/32
111/16
225/64
49/16
17/64
23
/64
(2)-9/16
6.1
5.4
115/16
FYTM 115/16 TF
YAR 211-115-2F
9810
81/2
71/4
13
/16
17/8
215/32
15/32
(2)-5/8
6.7
262
/16
/16
/32
Take-up / standard duty

TU-TF
Cast-iron housing
Wide slot
Set screw locking
Narrow inner ring
M-seal
Replaces: YTU, ST, VTWS-200, WSTU-SC, TH3-U200N
How to order
TU 1 TF
Option
Specify
Multi-function seal
Nonrelubricatable
TU 1 TR
TU 1 TFW
Shaft Pillow block

dia. designation
da
Bearing
designation
in
3
/4
TU 3/4 TF
13
YAR 204-012-2F
Dynamic
capacity
C
A
lbf
in
2860
35/8
37
Mass
B
lb
3
25
/64 27/16
63
/64 2 /64
63
/64
111/32
/64
11
3 /16 2 /32
/4
313/16 21/8
/2
21/8
23
25
/32
/8
117/64
17
/8
19
1 /64
17
/8
129/64
17
/32 2.0
/16 TU 13/16 TF
/8
TU 7/8 TF
15
/16 TU 15/16 TF
1
TU 1 TF
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
3150
3 /64 3
25
11/16
11/8
13/16
11/4
TU
TU
TU
TU
11/16 TF
11/8 TF
13/16 TF
11/4 ATF
YAR
YAR
YAR
YAR
206-101-2F
206-102-2F
206-103-2F
206-104-2F
4390
43/32 31/2
25
/64 23/4
17/64 129/64
55
/64 431/64 213/64 5/8
11/4
15/16
13/8
17/16
TU
TU
TU
TU
11/4 TF
15/16 TF
13/8 TF
17/16 TF
YAR
YAR
YAR
YAR
207-104-2F
207-105-2F
207-106-2F
207-107-2F
5740
41/16 31/2
15
/32 35/64
13/16 123/64
55
/64 55/64 233/64
11
/16 233/64 1
43
11/2
TU 11/2 TF
YAR 208-108-2F
6910
417/32 331/32
19
/32 315/32 119/64 159/64 19/64 545/64 317/64
53
/64 317/64 13/16
/4
131/32
11
/16 5.2
15/8
TU 15/8 TF
111/16 TU 111/16 TF
13/4
TU 13/4 TF
YAR 209-110-2F
YAR 209-111-2F
YAR 209-112-2F
7470
439/64 331/32
19
/32 327/64 13/8
317/64 13/16
/4
159/64
11
5.3
/16 5.2
5.2
115/16 TU 115/16 TF
YAR 210-115-2F
7900
439/64 331/32 5/8
335/64 127/64 159/64 19/64 57/8
325/64 19/32
/4
159/64
11
/16 5.3
2
23/16
YAR 211-200-2F
YAR 211-203-2F
9810
53/4
411/64 139/64 223/64 13/8
347/64 15/16
63
TU 2 TF
TU 23/16 TF
51/8
33
/4
1 /32
/4
15
19
/16 2 /64
159/64 19/64 521/32 317/64 3/4
317/64 3/4
647/64 41/64
/8
215/64
/32
/8
/64 11/2
/32
2.0
2.0
2.0
1.9
2.8
/32 2.8
2.7
2.6
3.5
/32 3.5
3.5
3.4
17
/64 223/64 11/16
9.4
8.4
263
Ball bearing units

TU-WF
Cast-iron housing
Wide slot
Eccentric locking
Wide inner ring
M-seal & flingers
Replaces: RTU, VTWE-200, WSTU-SXR
How to order
TU 1 WF
Option
Specify
Multi-function seal
Nonrelubricatable
TU 1 WR
TU 1 WFW
Shaft Pillow block

dia. designation
da
Bearing
designation
in
Dynamic
capacity
C
A
lbf
TU 3/4 WF
YEL 204-012-2F 2860
13
/16
/8
15
/16
1
TU 13/16 WF
TU 7/8 WF
TU 15/16 WF
TU 1 WF
YEL
YEL
YEL
YEL
11/16
11/8
13/16
11/4
TU
TU
TU
TU
11/16 WF
11/8 WF
13/16 WF
11/4 AWF
11/4
15/16
13/8
17/16
TU
TU
TU
TU
11/4 WF
15/16 WF
13/8 WF
17/16 WF
11/2
TU 11/2 WF
Mass
B
205-013-2F
205-014-2F 3150
205-015-2F
205-100-2F
3 /64 3
25
/64 2 /64
63
YEL
YEL
YEL
YEL
206-101-2F
206-102-2F 4390
206-103-2F
206-104-2F
43/32 31/2
25
/64 23/4
17/64 129/64
23
/64 431/64 213/64
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F 5740
207-106-2F
207-107-2F
41/16 31/2
15
/32 35/64 13/16 129/64
23
/64 55/64
YEL 208-108-2F 6910
417/32 331/32
19
/32 315/32 119/64 159/64 19/64
545/64 217/64
27
15/8
TU 15/8 WF
111/16 TU 111/16 WF
13/4
TU 13/4 WF
YEL 209-110-2F
YEL 209-111-2F 7470
YEL 209-112-2F
439/64 331/32
19
/32 327/64 13/8
521/32 317/64
115/16 TU 115/16 WF
YEL 210-115-2F 7900
439/64 331/32 5/8
335/64 127/64 159/64 19/64
57/8
2
23/16
YEL 211-200-2F 9810

YEL 211-203-2F
53/4
311/64 139/64 133/64 13/8
647/64 41/64 13/32 347/64 123/32
TU 2 WF
TU 23/16 WF
35/8
37
264
lb
25
in
3
/4
51/8
/64 27/16
33
/4
63
/64
111/32
/64
11
1 /32
/4
/4
159/64 19/64
313/16 21/8
15
3 /16 2 /32
43
/64 21/8
/8 117/64
17
/32
2.0
/8 1 /64
17
/32
2.3
2.2
2.2
2.1
/8 129/64
17
/32
3.0
2.9
2.9
2.9
/32 11/2
17
/32
3.5
3.5
3.5
3.4
/32 317/64 13/8
/4 131/32
11
/16
4.7
27
/32 317/64 13/8
/4 159/64
11
/16
6.1
6.0
6.0
31
/32 325/64 11/2
/4 159/64
11
/16
5.8
/64 133/64 11/16
9.4
9.0
11
/16 2 /64
1 /16
23
/32 23/64
13/16
223/64 3/4
317/64
13/64
233/64 117/64
19
21
63

TU-FM
Cast-iron housing
Wide slot
Eccentric locking
Narrow inner ring
M-seal
Replaces: VTU, VTWE-100, WSTU-SXV
How to order
TU 1 FM
Option
Specify
Nonrelubricatable
TU 1 FMW
Shaft Pillow block

dia. designation
da
in
3
/4
TU 3/4 FM
13
Bearing
designation
Dynamic
capacity
C
lbf
in
YET 204-012 2860
Mass
35/8
25
/64 27/16
63
/64 2 /64
63
/64
111/32
/64
11
1 /32
/4
313/16 21/8
YET 205-013
YET 205-014 3150
YET 205-015
YET 205-100
3 /64 3
25
11/16
11/8
13/16
11/4
TU
TU
TU
TU
11/16 FM
11/8 FM
13/16 FM
11/4 AFM
YET 206-101
YET 206-102 4390
YET 206-103
YET 206-104
33/32
31/2
25
/64 23/4
17/64
11/4
15/16
13/8
17/16
TU
TU
TU
TU
11/4 FM
15/16 FM
13/8 FM
17/16 FM
YET 207-104
YET 207-105 5740
YET 207-106
YET 207-107
41/16
31/2
15
/32 35/64
13/16
11/2
TU 11/2 FM
YET 208-108 6910
417/32 331/32
19
15/8
TU 15/8 FM
111/16 TU 111/16 FM
13/4
TU 13/4 FM
YET 209-110
YET 209-111 7470
YET 209-112
439/64 331/32
19
115/16 TU 115/16 FM
YET 210-115 7900
439/64 331/32
/8
335/64 127/64 159/64 19/64 57/8
2
23/16
YET 211-200 9810

YET 211-203
53/4
/4
311/64 15/8
TU 2 FM
TU 23/16 FM
lb
/16 TU 13/16 FM
/8
TU 7/8 FM
15
/16 TU 15/16 FM
1
TU 1 FM
7
37
51/8
33
/64 21/8
/4
3 /16 2 /32
19
129/64
431/64 213/64
23
129/64
45/64
/8
15
19
/64 2 /64
/64 23/32
59
1 /64
13/64
19
17
/8 1 /64
17
/8 129/64
17
/32
2.1
2.1
2.1
1.9
3.0
/32 2.8
2.7
2.8
3.4
/32 3.6
3.4
3.2
/32 315/32 119/64 159/64 19/64 445/64 217/64 7/16 317/64 19/32
/4 131/32
11
/16 5.2
/32 327/64 13/8
19/32
/4 159/64
11
5.8
/16 5.2
5.2
217/64 7/16 325/64 19/32
/4 159/64
11
/16 5.3
133/64 13/8
647/64 41/64
/16 39/32
15
/32 347/64 17/16
21
/32 2.0
17
115/16 15/32 521/32 39/32
233/64 15/32
/8 117/64
/32 11/2
/8
223/64 3/8
159/64
/64 159/64 11/16 8.8

8.6
63
265
Ball bearing units

Take-up / medium duty
TUM-TF
Cast-iron housing
Wide slot
Set screw locking
Wide inner ring
M-seal & flingers
Replaces: MST, VTWS-300, WSTU-SCM, TC-35
How to order
TUM 17/16 TF
Option
Specify
Multi-function seal
Nonrelubricatable
TUM 17/16 TR
TUM 17/16 TFW
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
lbf
in
129/64
TUM 1 TF
YAR 206-100-2F
4390
43/32
31/2
25
/64 23/4
17/64
129/64
55
/64 431/64 213/64 5/8
13/16
TUM 13/16 TF
YAR 207-106-2F
5740
41/16
31/2
15
/32 35/64
13/16
123/64
55
/64 55/64 223/64
11
43
17/16
TUM 17/16 TF
YAR 208-107-2F
6910
417/32 331/32
19
119/64 159/64 19/64 545/64 317/64
53
131/32
11
/16
11/2
TUM 11/2 TF
YAR 209-108-2F
7470
439/64 331/32
19
13/8
317/64 13/16
159/64
11
/16
111/16
TUM 111/16 TF
YAR 210-111-2F
7900
439/64 331/32
/8
335/64
127/64 159/64 19/64 57/8
325/64 19/32
159/64
11
/16
13/4
TUM 13/4 TF
YAR 210-112-2F
115/16
TUM 115/16 TF
YAR 211-115-2F
9810
53/4
/4
411/64
139/64 233/64 13/8 647/64 41/64
347/64 15/16
63
266
51/8
/32 327/64
/32 315/32
215/64
/8
/16 233/64 1
/64 317/64 13/16
159/64 19/64 521/32 317/64 3/4

317/64 3/4
/8
/8
/64 11/2
/4
/4
/4
17
/32
17
/32
/64 233/64 11/16
Pillow block / light duty

S-FM
Pressed steel housing
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: PB, SSPE-100, P2B-SLX
How to order
S 1 FM
Option
Specify
None
S 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
A
lbf
2150
S 3/4 FM
YET 204-012
2860
11/8
13
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
S 13/16 FM
S 7/8 FM
S 15/16 FM
S 1 FM
11/16
11/8
13/16
11/4
S
S
S
S
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
/16
/8
15
/16
7
11/16 FM
11/8 FM
13/16 FM
11/4 AFM
/4-28
/4-28
/4-28
/16-24
Mass
(No. reqd)
lb
YET 203-008
YET 203-010
/4
Bolts
in
S 1/2 FM
S 5/8 FM
/2
/8
Bolt
hole
dia.
/8
35/8
49/32 11/8
/32
211/16
13/4
/32
33/8
21/4
19
/4
1 /8
4 /32 1 /8
/32
3 /8
2 /4
19
15/16
47/8
11/4
/32
33/4
25/8
23
/8
11
/32
(2)-5/16
0.5
0.5
/32
(2)-5/16
0.6
/64
59
13
/64
59
13
/32
(2)- /64
0.7
0.7
0.6
0.7
/64
13/64
13
/32
(2)-25/64
1.1
1.1
1.0
1.2
/64
/64
25
267
Ball bearing units

Pillow block / light duty
SR-FM
Pressed steel housing
Rubber cartridge
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: RPB, SSRPE-100
How to order
SR 1 FM
Option
Specify
None
SR 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
A
lbf
Bolt
hole
dia.
Bolts
Mass
(No. reqd)
in
lb
SR 1/2 FM
SR 5/8 FM
YET 203-008
YET 203-100
2150
11/8
49/32
11/8
/32
33/8
21/4
19
/64
59
/64
13
/32
(2)-5/16
0.6
SR 3/4 FM
YET 204-012
2860
11/8
49/32
11/8
/32
33/8
21/4
19
/64
59
/64
13
/32
(2)-5/16
0.7
13
SR 13/16 FM
SR 7/8 FM
SR 15/16 FM
SR 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
15/16
47/8
11/4
/32
33/4
25/8
19
/64
59
/64
13
/32
(2)-25/64
1.0
0.9
0.9
1.0
/2
/8
/4
/16
/8
15
/16
1
7
/4-28
/4-28
/4-28
268
Flangette / light duty

F-FM
Pressed steel flange
Three-bolt mounting
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: RA, SSF3E-100, F3B-SLX
How to order
F 1 FM
Option
Specify
None
F 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
A
lbf
Bolts
B
lb
YET 203-008
YET 203-010
2150
33/16
431/64
/32
461/64
45/64 159/64
F 3/4 FM
YET 204-012
2860
337/64
213/16
/16
/64
211/64
19
/64
59
11
13
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
347/64
/8
15/32
/64
223/64
19
/64
59
11
F 13/16 FM
F 7/8 FM
F 15/16 FM
F 1 FM
11/16
11/8
13/16
11/4
F
F
F
F
11/16 FM
11/8 FM
13/16 FM
11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
13
4 /32
3 /16
/8
1 /32
/32
51
2 /64
23
/64
1 /64
13
11/4
15/16
13/8
17/16
F
F
F
F
11/4 FM
15/16 FM
13/8 FM
17/16 FM
YET 207-104
YET 207-105
YET 207-106
YET 207-107
5740
451/64
315/16
25
11/4
/32
33/16
15/32
/4
/16
/8
15
/16
7
(No. reqd)
in
F 1/2 FM
F 5/8 FM
/2
/8
/4-28
/4-28
/4-28
/16-24
/8-24
Mass
/64
/4
/8
/8
/64
/64
(3)-15/64
0.6
0.6
/32
(3)-5/16
0.7
/32
(3)-5/16
0.9
0.9
0.8
0.8
/32
/32
/16
(3)- /8
1.4
1.4
1.3
1.3
(3)-25/64
1.9
1.9
1.8
1.7
269
Ball bearing units

Flangette / light duty
FT-FM
Pressed steel flange
Two-bolt mounting
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: RAT, SSF2E100, F2B-SLX
How to order
FT 1 FM
Option
Specify
None
FT 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
A
lbf
Bolts
B
2150
33/16 21/2
/32
FT 3/4 FM
YET 204-012
2860
39/16 213/16
/16
13
/16
/8
15
/16
1
FT 13/16 FM
FT 7/8 FM
FT 15/16 FM
FT 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
33/4
11
11/16
11/8
13/16
11/4
FT 11/16 FM
FT 11/8 FM
FT 13/16 FM
FT 11/4 AFM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
/4-28
/4-28
/4-28
/16-24
270
(No. reqd)
lb
YET 203-008
YET 203-010
/4
in
FT 1/2 FM
FT 5/8 FM
/2
/8
Mass
4 /16 3 /16
/32
11
/32
61
/64
/32 159/64
/4
25/16
/8
/64
(2)-1/4
0.5
0.5
/64
(2)-5/16
0.6
(2)-5/16
0.7
0.7
0.7
0.6
19
/64
25/8
59
/64
19
/64
251/64
59
/64
11
1 /32
/64 211/64
/64 223/64
51
/64 2 /64
23
/64
3 /16
1 /64
13
/32
/32
25
(2)- /64
1.1
1.1
1.0
0.9
Rubber cartridge / light duty

R-FM
Rubber cartridge
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: RCSM
How to order
R 1 FM
Option
Specify
None
R 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
D
lbf
Mass
d2
lb
YET 203-008
YET 203-010
2150
217/32
11/8
13/8
R 3/4 FM
YET 204-012
2860
217/32
119/64
19/16
19
13
/16
/8
15
/16
1
R 13/16 FM
R 7/8 FM
R 15/16 FM
R 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
3150
217/32
115/32
125/32
19
11/16
11/8
13/16
11/4
R
R
R
R
11/16 FM
11/8 FM
13/16 FM
11/4 FM
YET 206-101
YET 206-102
YET 206-103
YET 206-104
4390
/4
in
R 1/2 FM
R 5/8 FM
/2
/8
/4-28
/4-28
/4-28
/16-24
3 /32
47
1 /64
2 /64
/64
59
/64
59
/4
23
/64
1 /16
/8
/64
/64
1 /64
0.5
0.3
0.5
0.6
0.6
0.6
0.5
0.7
0.7
0.7
0.7
271
Ball bearing units

Rubber cartridge / light duty
G-FM
Rubber cartridge
Eccentric locking
Narrow inner ring
Nonrelubricatable
M-seal
Replaces: RARB
How to order
G 1 FM
Option
Specify
None
G 1 FM
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Dynamic
capacity
C
Set screw
size
D
lbf
G 3/4 FM
YET 204-012
13
G 13/16 FM
G 7/8 FM
G 15/16 FM
G 1 FM
YET 205-013
YET 205-014
YET 205-015
YET 205-100
/4
/16
/8
15
/16
1
7
d2
in
lb
2860
21/16
119/64
139/64
19
3150
29
15
13
19
272
Mass
/4-28
/4-28
2 /64
1 /32
1 /16
/64
11
/64
25
/16
59
/32
59
/64
0.5
/64
0.6
0.6
0.6
0.5
Wide inner ring ball bearings
The basic protection

M seal
Positive outer
ring retention
Wear
resistant
elastomer
The pressed steel washer or guard

forms a narrow gap with the
cylindrical surface of the inner ring
shoulder providing protection against
larger contaminants.
Steel trash
guard
A synthetic rubber lip is bonded to a

pressed steel washer. This provides
protection against small contaminants. It also retains the grease and
allows for grease purging.
Ground sealing
with precision
surface run-out
tolerance
Hinged sealing lip

provides uniform
contact pressure
for positive sealing
and higher speed
capabilities
Long life grease

The new SKF standard grease is a
high quality grease that contains a
lithium/calcium complex soap.
Properties
High level of mechanical
stability even in the most severe
conditions
Very good extreme pressure and
anti-wear properties
Very good water resistance
Very good anti-rust and
anti-corrosion protection
Exceptional characteristics at
both high and low temperatures
Grease characteristics
Base
Lithium-Calcium
Application temperature
-4 to 248 F (-20 to 120 C)
NLGI
Viscosity at 100 F (40 C)
900 SUS (190 cSt)
Dropping point
389 F
Locking methods
Inner ring distortion vs. angle between set screws
Shaft locking methods

Set screw locking features two set screws
120 apart. This placement of the set screws
maximizes holding power while minimizing
inner ring distortion. Other factors such as:
zone hardening of the bearing inner ring,
drilling and tapping after heat treat, proper
screw length, a knurled cup point set screw
and forged set screw socket have been incorporated to further enhance holding power
and vibration resistance (backout).
120
SKF-120
set screw angle
Balanced
Increasing
distortion
0
120
120
120
Balanced 3-point contact
30
60
90
120 150 180
Set screw angle
120 set screw spacing minimizes inner ring distortion.

This results in lower vibration and better sealing.
273
Ball bearing units

Nomenclature
Wide inner ring ball bearings
Y E T 207 107 CW
4
1
2
3
1. Bearing type:
4. Suffix:
YET
Narrow inner ring, eccentric lock
Cylindrical O.D.
YEL
Wide inner ring, eccentric lock
Nonrelubricatable bearing, no lube holes in outer ring
YAR
Wide inner ring, set screw lock
Groove in outer ring (opposite locking side)
YAT
Narrow inner ring, set screw lock
GR
Groove in outer ring (on locking side)
1726
Standard inner ring, no set screws, press fit required
-2F
Bearing with two flingers
-2RF
Bearing with two multi-function seals
No locking collar
2. Basic bearing size:
3. Bore size:
Example: 107 is 1716
Competitor comparison:
Description
SKF
Dodge
Sealmaster
Torrington/Fafnir
Linkbelt
Insert bearing
YAT 2XX-XXX
VSC
GYAXXXRRB
SG2XXEL
Pillow block
SY - RM
VSC
VP
SAS
P3-S2--E
4-bolt flange
FY - RM
VSC
VF
SCJ
F3-S2--E
2-bolt flange
FYT - RM
VSC
VFT
SCJT
FX3-2--E
274
Spherical O.D. / standard duty

YET
Spherical O.D.
Eccentric locking
Narrow inner ring
Relubricatable
M-seal
Replaces: GRA-RRB, WG200UL
How to order
YET 205-100
Option
Specify
No collar
Nonrelubricatable
Lube groove
Lube groove (collar side)
YET 205-100U
YET 205-100W
YET 205-100G
YET 205-100GR
For seal speed limits see page 242.
Load ratings
Designation
(1)
Co
lbf
YET 203-008
YET 203-010
YET 203
YET 204-012
YET 204
YET 205-013
YET 205-014
YET 205-015
YET 205-100
YET 205
YET 206-101
YET 206-102
YET 206-103
YET 206-104
YET 206
YET 207-104
YET 207-105
YET 207-106
YET 207-107
YET 207
YET 208-108
YET 208
YET 209-110
YET 209-111
YET 209-112
YET 209
YET 210-115
YET 210
B1
B2
in
C1
d1
mm
in
mm
in
12
mm
d2
in
Set screw
size
1070
/4
11/8
17
/32
/32
40
/2
/8
61
in
in
lb
0.012
0.024
/64
15/64
17/64
19/32
19
/4
/4-28 x 1/4
17
2860
1470
27
/32
17/32
17
/32
14
/32
47
/4
/64
/4-28 x 1/4
0.37
0.35
25
0.49
0.47
0.43
0.41
0.41
/16
/8
15
/16
1
7
4390
1750
2520
27
/32
15
/16
17/32
13
1 /32
17
/32
/8
15
18
/8
52
/32
62
121/64 115/32
11/16
11/8
13/16
11/4
19
/64
0.024
/4-28 x 1/4
0.024
47
23
13
1 /16 2 /64
0.039
23/64
27/32
0.039
215/64 27/16
0.039
215/32 241/64
0.039
223/32 215/16
15
0.039
263/64 31/4
17
0.06
1 /16
1 /64
/64
/16-24 x /16
30
5740
3440
17
1 /32
11
/16
19
/32
72
11/4
15/16
13/8
17/16
/8
/8-24 x /8
35
6910
4270
13/16
123/32
23
/32
21
/16
80
11/2
/16
/8-24 x 3/8
40
7470
4860
13/16
123/32
23
/32
22
/16
85
15/8
111/16
13/4
/16
/8-24 x 3/8
45
7900
5220
13/16
123/32
23
/32
22
/16
90
115/16
/16
/8-24 x 3/8
50
9810
YET 212-204
YET 212-207
11900
6520
19/32
129/32
13
/16
25
/32
100
2
23/16
/32
55
8090
115/32
23/32
/8
26
/32
110
If bearings are mounted on shafts with interference fits, then C values may be multiplied by 1.3.
21/4
27/16
0.28
0.24
0.24
20
13
3150
Mass
2150
YET 211-200
YET 211-203
YET 211
(1)
Min. fillet
radius
/32
0.75
0.71
0.66
0.62
0.68
1.09
1.13
1.06
0.94
0.98
1.38
1.32
1.66
1.57
1.49
1.46
1.61
1.58
2.53
/16-20 x 7/16 2.18
2.21
2.81
/16-20 x 7/16 2.81
275
Ball bearing units

YEL-2F
Spherical O.D.
Eccentric locking
Wide inner ring
Relubricatable
M-seal & flingers
Replaces: G-KRRB, YG200NL
How to order
YEL 205-1002F
Option
Specify
No collar
Nonrelubricatable
Lube groove
Multi-function seal
YEL
YEL
YEL
YEL
YEL
205-100-2U
205-100-2FW
205-100-2FG
205-100-2FGR
205-100-2RF
Load ratings
Min. fillet
radius
Designation
C
Co
lbf
YEL 204-012-2F
YEL 204-2F
2860
B1
B2
in
1470
111/32
123/32
17
/32
C1
mm
in
mm
in
14
/64
47
d1
mm
/4
d2
in
in
in
17/64
19/32
43
21
15
1 /32
11
47
23
/64
lb
0.024
/4-28 x 1/4
0.024
0.024
13
205-013-2F
205-014-2F
205-015-2F
205-100-2F
205-2F
YEL
YEL
YEL
YEL
YEL
206-101-2F
206-102-2F
206-103-2F
206-104-2F
206-2F
YEL
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
207-2F
5740
YEL 208-108-2F
YEL 208-2F
6910
/16
3150
1750
1 /8
1 /4
17
/32
15
/8
52
8
15
16
1 /64
/16
/4-28 x /4
0.45
0.50
0.54
0.51
0.52
25
4390
2520
1 /16
29
1 /32
/8
18
/32
62
11/16
11/8
13/16
11/4
1 /16
1 /64
/32
/16-24 x /16
0.85
0.79
0.73
0.81
30
3440
131/64
21/64
11
/16
19
/64
72
11/4
15/16
13/8
17/16
113/16
21/64
47
0.039
1.31
1.30
1.21
1.11
1.16
23/64
2732
27
0.039
1.61
1.54
215/64
27/16
27
0.039
1.92
1.86
1.74
1.72
215/32
241/64
31
0.039
2.02
1.98
223/32
215/16 13/32
0.039
263/64
31/4
17/32
0.059
35/8
31516
115/32
0.059
/64
/8-24 x 3/8
35
4270
111/16
27/32
23
4860
11
23
/32
209-110-2F
209-111-2F
209-112-2F
209-2F
7470
YEL 210-115-2F
YEL 210-2F
7900
5220
115/16
215/32
23
YEL 211-200-2F
YEL 211-203-2F
YEL 211-2F
9810
6520
23/16
213/16
13
YEL 212-204-2F
YEL 212-207-2F
YEL 212-2F
11900 8090
YEL 215-215-2F
14900 11000
1 /16
2 /32
/32
21
11
22
/64
/16
80
11/2
85
15/8
111/16
13/4
40
/32
/32
/8-24 x 3/8
/8-24 x 3/8
45
/32
/16
22
25
/16
/32
90
115/16
100
2
23/16
50
/32
55
229/64
31/16
/8
26
/32
110
21/4
27/16
60
215/16
35/8
15
/16
276
Mass
20
YEL
YEL
YEL
YEL
YEL
YEL
YEL
YEL
YEL
Set screw
size
29
/4
130
215/16
/8-24 x 3/8
2.76
/16-20 x 7/16 2.73
2.85
4.12
/16-20 x 7/16 3.51
3.64
/16-20 x 7/16 5.77
Cylindrical O.D. / standard duty

YEL-2FCW
Cylindrical O.D.
Eccentric locking
Wide inner ring
Nonrelubricatable
M-seal
Replaces: KRR, YB200NL
How to order
YEL 205-100-2FCW
Option
Specify
No collar
Relubricatable
Multi-function seal
YEL 205-100-2FCWU
YEL 205-100-2FC
YEL 205-100-2RFCW
Load ratings
Min. fillet
radius
Designation
C
Co
lbf
YEL 204-012-2F CW
YEL
YEL
YEL
YEL
205-013-2F
205-014-2F
205-015-2F
205-100-2F
CW
CW
CW
CW
YEL
YEL
YEL
YEL
206-101-2F
206-102-2F
206-103-2F
206-104-2F
CW
CW
CW
CW
YEL
YEL
YEL
YEL
207-104-2F
207-105-2F
207-106-2F
207-107-2F
CW
CW
CW
CW
2860
B1
B2
in
1470
111/32
123/32
17
/32
d1
mm
mm
in
in
47
14
/4
d2
Set screw
size
in
17/64
19/32
43
/64
lb
0.024
/4-28 x 1/4
13
52
21
1 /64
15
1 /32
11
/16
0.024
62
11/16
11/8
13/16
11/4
19/16
147/64
23
/32
0.024
19
72
11/4
15/16
13/8
17/16
13
1 /16
2 /64
47
0.039
/32
21
80
11/2
23/64
27/32
27
/32
0.039
1.61
23
/32
22
85
15/8
111/16
13/4
215/64
2716
27
/32
0.039
1.92
1.86
1.74
215/32
23
/32
22
90
115/16
215/32
241/64
31
/32
0.039
2.02
23/16
213/16
13
/16
25
100
2
23/16
223/32
215/16
13/32
0.039
229/64
31/16
26
110
21/4
27/16
263/64
31/4
17/32
0.059
1750
1 /8
1 /4
17
2520
1 /16
29
5740
3440
31
1 /64
2 /64
11
/16
YEL 208-108-2F CW
6910
4270
111/16
27/32
23
YEL 209-110-2F CW
YEL 209-111-2F CW
YEL 209-112-2F CW
7470
4860
111/16
27/32
YEL 210-115-2F CW
7900
5220
115/16
YEL 211-200-2F CW
YEL 211-203-2F CW
9810
6520
YEL 212-204-2F CW
YEL 212-207-2F CW
11900 8090
4390
0.45
/16
/8
15
/16
1
7
3150
Mass
1 /32
/32
/8
/8
15
18
/64
/4-28 x /4
/16-24 x 5/16
/8-24 x /8
/8-24 x 3/8
/8-24 x 3/8
/8-24 x 3/8
/16-20 x 7/16
/16-20 x 7/16
0.62
0.50
0.54
0.51
0.90
0.85
0.79
0.73
1.31
1.30
1.21
1.11
2.76
2.73
4.12
3.51
277
Ball bearing units

YAR-2F
Spherical O.D.
Set screw locking
Wide inner ring
Relubricatable
M-seal & flingers
Replaces: GYA-RRB, UG200NL
How to order
YAR 205-100-2F
Option
Specify
Nonrelubricatable
Lube groove
Multi-function seal
YAR
YAR
YAR
YAR
205-100-2FW
205-100-2FG
205-100-2FGR
205-100-2RF
Load ratings
Min. fillet
radius
Designation
C
Co
lbf
YAR 203-008-2F
YAR 203-010-2F
YAR 203-2F
YAR 204-012-2F
YAR 204-2F
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
YAR
205-013-2F
205-014-2F
205-015-2F
205-100-2F
205-2F
206-101-2F
206-102-2F
206-103-2F
206-104-2F
206-2F
207-104-2F
207-105-2F
207-106-2F
207-107-2F
207-2F
YAR 208-108-2F
YAR 208-2F
YAR
YAR
YAR
YAR
209-110-2F
209-111-2F
209-112-2F
209-2F
B4
in
C1
mm
in
mm
in
12
1070
15/64
0.16
/32
2860
3150
1470
1750
17/32
11
1 /32
0.18
0.20
14
15
/64
/8
in
/2
/8
61
29
/64
/64
0.012
47
52
/4
20
17/64
/2
lb
10-32 x 1/4
10-32 x 1/4
0.25
0.22
0.21
0.34
0.33
/4-28 x 14
0.024
13
/16
/8
15
/16
1
21
1 /64
/16
0.024
/4-28
/4-28
1
/4-28
1
/4-28
x
x
x
x
/4
/4
/4
1
/4
0.46
0.48
0.45
0.41
0.42
x
x
x
x
/4
/4
/4
1
/4
0.75
0.70
0.65
0.60
0.66
/16
/16
/16
5
/16
1.08
1.02
0.97
0.91
0.97
/16-24 x 5/16
1.40
1.31
/16-24 x 5/16
/16-24 x 5/16
5
/16-24 x 5/16
1.67
1.58
1.48
1.45
1.70
1.64
/8-24 x 3/8
/8-24 x 3/8
2.57
2.19
2.25
/8-24 x 3/8
/8-24 x 3/8
3.35
2.86
3.05
/8-24 x 3/8
/8-24 x 3/8
4.07
3.52
3.87
1
1
25
1
4390
2520
1 /2
0.20
18
/32
62
1 /16
11/8
13/16
11/4
/4-28
/4-28
1
/4-28
1
/4-28
1
1 /16
/8
0.024
1
1
30
1
5740
3440
11
1 /16
0.24
19
/64
72
1 /4
15/16
13/8
17/16
/16-24
/16-24
5
/16-24
5
/16-24
5
13
1 /16
11
23/64
/16
0.039
x
x
x
x
5
5
35
6910
7470
4270
115/16
4860
15
1 /16
0.31
0.31
21
11
22
/64
/16
80
1 /2
85
15/8
111/16
13/4
40
15
2 /64
/4
0.039
/4
0.039
215/32
/4
0.039
223/32
/8
0.039
45
21/32
0.35
22
YAR 211-200-2F
YAR 211-203-2F
YAR 211-2F
9810
6520
23/16
0.35
25
/16
/32
15
90
1 /16
100
2
23/16
50
/8-24 x 3/8
55
1
11900
8090
29/16
0.39
26
/32
110
2 /4
27/16
263/64
0.059
31/4
0.059
35/8
11/16
60
1
12900
8990
211/16
0.39
27
/32
120
2 /2
211/16
65
14900
11000
27/8
0.47
278
40
5220
YAR 215-212-2F
YAR 215-215-2F
in
17
7900
YAR 213-208-2F
YAR 213-211-2F
YAR 213-2F
mm
29
/4
130
2 /4
215/16
Mass
2150
YAR 210-115-2F
YAR 210-2F
YAR 212-204-2F
YAR 212-207-2F
YAR 212-2F
d1
Set screw
size
0.059
/16-20 x 7/16
/16-20 x 7/16
5.32
4.67
Spherical O.D. / medium duty

YAR-2F
Spherical O.D.
Set screw locking
Wide inner ring
Relubricatable
M-seal & flingers
How to order
YAR 208-107-2F
Option
Specify
Nonrelubricatable
Lube groove
Multi-function seal
YAR
YAR
YAR
YAR
208-107-2FW
208-107-2FG
208-107-2FGR
208-107-2RF
Load ratings
Min. fillet
radius
Designation
C
Co
lbf
B4
C1
in
in
mm
in
mm
in
d1
Set screw
size
Mass
in
lb
YAR 208-107-2F
6910
4270
115/16
0.31
21
11
80
17/16
23/64
0.039
1.48
YAR 209-108-2F
7470
4860
115/16
0.31
22
85
11/2
215/64
0.039
1.83
YAR 210-111-2F
YAR 210-112-2F
5220
21/32
0.35
22
90
111/16
13/4
215/32
7900
0.039
2.10
2.00
YAR 211-115-2F
9810
6520
23/16
0.35
25
100
115/16
223/32
YAR 212-203-2F
11900
8090
29/16
0.39
26
110
23/16
263/64
YAR 214-207-2F
YAR 214-208-2F
14000
10100
23/4
0.47
28
15
125
27/16
21/2
YAR 215-211-2F
14900
11000
27/8
0.47
29
130
YAR 216-215-2F
YAR 216-300-2F
16400
12400
31/16
0.47
30
17
140
/64
/16
/16
/32
/32
/64
/4
/64
/4
/4
/4
/16-24 x 5/16
/16-24 x 5/16
/8-24 x 3/8
/8-24 x 3/8
0.039
2.69
0.059
3.42
327/64
13/16
0.059
5.21
5.02
211/16
35/8
11/16
0.059
215/16
3
327/32
13/16
0.079
/8
/8-24 x 3/8
/8-24 x 3/8
/16-20 x 7/16
/16-20 x 7/16
/16-20 x 7/16
5.52
6.25
6.00
/16-20 x 7/16
/16-20 x 7/16
279
Ball bearing units

Spherical O.D./ standard duty
YAT
Spherical O.D.
Set screw locking
Narrow inner ring
Relubricatable
M-seal
Replaces: GYA-RRB, V-, INS-SL
Designation
YAT 203-008
YAT 203-010
YAT 203
YAT 204-012
YAT 204
YAT 205-014
YAT 205-015
YAT 205-100
YAT 205
YAT 206-102
YAT 206-103
YAT 206-104
YAT 206
YAT 207-104
YAT 207-106
YAT 207-107
YAT 207
YAT 208-108
YAT 208
Basic load ratings

C
Co
lbf
lbf
Mass
B
B4
C1
in
in
mm
in
mm
in
12
40
14
47
57
64
2150
0.16
32
1070
2860
1470
0.20
64
in
in
mm
61
0.01
10-32 x 4
0.22
0.87
0.16
1764
32
0.02
0.30
0.24
12164
19
0.02
0.40
0.37
0.35
0.31
0.04
0.60
0.59
0.57
0.51
0.04
0.95
0.85
0.79
0.68
0.04
1.22
0.95
16
16
0.04
0.04
1.39
1.39
1.31
1.06
16
0.04
1.46
1.19
64
in
lb
1
4-28 x 14
20
1564
3150
0.20
15
62
1 8
1316
114
30
1916
23
72
114
138
1716
35
11316
80
112
2364
29
52
1750
8
16
1
15
64
4-28 x 14
25
4390
2520
5740
3440
6910
4270
1 32
0.27
18
138
0.29
19
13764
0.31
21
11
32
64
64
64
64
16-24 x 516
16-24 x 516
16-24 x 516
40
158
158
0.31
0.31
22
22
4860
YAT 210-115
YAT 210
7900
5220
14564
0.35
22
YAT 211-200
YAT 211-203
9810
6520
12532
0.35
YAT 212-204
YAT 212-207
11900
8090
12932
YAT 215-215
14900
11000
2764
85
85
158
11116
134
45
21564
21564
90
11516
50
21532
25
100
2
2316
22332
31
64
0.04
2.20
1.88
0.35
26
110
214
2716
26364
17
32
0.06
2.76
2.38
0.37
29
130
21516
358
37
64
0.06
3.78
280
2
8
Set
screw
size
17
7470
YAT 209-110
YAT 209-111
YAT 209-112
YAT 209
mm
d1
Min.
fillet
radius
16
16
16
32
32
16-24 x 516
16-24 x 516
8-24 x 38
8-24 x 38
8-24 x 38
8-24 x 38
Standard inner ring bearings

Spherical O.D./ standard duty
1726
Spherical O.D.
Press fit mounting
Standard inner ring
Nonrelubricatable
RS1 seal
How to order
1726205-2RS1
Option
Specify
None
1726205-2RS1
Load ratings
Mass
Designation
Speed rating
C
lb
Co
B
mm
1726202-2RS1
1750
843
11.00
35
1726203-2RS1
2150
1070
12.00
1726204-2RS1
2860
1470
1726205-2RS1
3150
1726206-2RS1
r1,2
in
rpm
lb
15
0.024
13000
0.09
40
17
0.024
12000
0.12
14.00
47
20
0.039
10000
0.21
1750
15.00
52
25
0.039
8500
0.24
4380
2520
16.00
62
30
0.039
7500
0.40
1726207-2RS1
5730
3440
17.00
72
35
0.043
6300
0.55
1726208-2RS1
6900
4270
18.00
80
40
0.043
5600
0.70
1726209-2RS1
7460
4860
19.00
85
45
0.043
5000
0.81
1726210-2RS1
7890
5220
20.00
90
50
0.043
4800
0.90
1726211-2RS1
9800
6520
21.00
100
55
0.059
4300
1.19
1726212-2RS1
10680
7300
22.00
110
60
0.059
4000
1.65
1726213-2RS1
12360
9100
23.00
120
65
0.059
3600
N/A
Load ratings
Mass
Designation
Speed rating
C
lb
Co
B
mm
1726305-2RS1
5060
2610
17.00
62
1726306-2RS1
6320
3600
19.00
1726307-2RS1
7460
4270
1726308-2RS1
9220
1726309-2RS1
1726310-2RS1
r1,2
in
rpm
lb
25
0.043
7500
0.44
72
30
0.043
6300
0.66
21.00
80
35
0.059
6000
0.88
5400
23.00
90
40
0.059
5000
1.21
11900
7080
25.00
100
45
0.059
4500
1.61
13900
8540
27.00
110
50
0.079
4300
2.09
281
Ball bearing units

Air handling ball bearing units
If youre responsible for designing high efficiency,

quiet-running air handling equipment, then you
know the importance of specifying the right
bearing for the job.
The right bearing not only meets the specific
performance requirements of your air handling
application, but also provides exceptional value
with:
On-time delivery
Superior product quality
Unsurpassed customer service
Technical support
As the world leader in rolling bearing technology, SKF is aware of the need for superior
bearing performance in air handling applications.
Thats why weve committed the resources and
have developed special ball bearing units to
meet the performance requirements of air
handling applications.
SKF air handling ball bearing units

feature ground and honed raceways and
high precision balls that are prelubricated
with quality grease. The grease is selected
specifically for air handling applications,
and helps ensure long service life.
Inner ring distortion vs. angle between set screws
120
SKF-120
set screw angle
Balanced 3-poi
Increasing
distortion
0
120
282
120
Balanced 3-point contact
30
60
90
120 150 180
Set screw angle

Closely controlled air-handling alignment
torque increases system reliability to allow
operating misalignment. An anti-rotation pin
ensures that the outer ring does not rotate.
120
120 set screw spacing minimizes inner ring distortion.

This results in lower vibration and better sealing.
Air handling grease and

sealing arrangement
Low friction contact seals and flingers allow
for high speed operation and provide superior
protection from contaminants in aggressive
operating environments. The seal features a
land riding design and is molded of synthetic
rubber.
Special air handling quality grease was
selected to accommodate very low start-up
temperatures and a broad operating
temperature range as well as wet corrosive
environments.
NOTE: The SKF air handling grease and sealing arrangement permit the
SKF new life method to be employed to optimally select bearings for longer
service life than indicated by conventional L10 life calculations. Please contact
SKF Applications Engineering for assistance.
Start-up capability of -30 F (-4 C)

Operating range of 0 to +230 F
(-18 to +118 C)
Good water resistance and rust
protection
Unit ball shaft

locking methods
Knurled cup set screws provide superior
holding power in both the set screw and
eccentric locking methods.
Set screw locking (YAR, YAT)
Accommodates reverse rotation
Optimized set screw location
Optimized holding power
Minimum inner ring distortion
Eccentric locking (YET, YEL)

For rotation in one direction
Easy to dismount
Does less damage to shaft
than normal set screw lock
Unit ball housing styles
SY, SYM, SYH
S, SR
FYT, FYTM
FYT, FYM
SKF air handling ball bearing units are available in a wide range of housing styles. These
units feature powder coated epoxy paint that
provides corrosion resistance superior to
conventional mounted bearing housings.
SKF also offers a wide assortment of ball
bearing products for air handling industry
applications, including stamped steel
housings (S, SR), rubber mounted cartridge
bearings (R, G) and other mounted products.
R, G
283
Ball bearing units

Air handling arrangements
Bearing
Housing
SY
YAR
YAT
FY-TF/AH
d 1/2 2 15/16 in
FYT-TF/AH
d 1/2 2 3/16 in
SYM-TF/AH
d 17/16 2 15/16 in
FYM-TF/AH
d 17/16 2 15/16 in
FYTM-TF/AH
d 17/16 115/16 in
SY-RM/AH
d 1/2 2 15/16 in
FY-RM/AH
d 1/2 2 3/16 in
FYT-RM/AH
d 1/2 2 3/16 in
FY-WF/AH
d 3/4 2 7/16 in
FYT-WF/AH
d 3/4 2 3/16 in
SYH-RM /AH
d 1/2 2 7/16 in
SYH-WF/AH
d 3/4 2 7/16 in
SY-FM/AH
d 3/4 2 3/16 in
SYH-FM/AH
d 1/2 2 3/16 in
YET
Consult SKF for availability of metric shaft sizes
284
FYT
SY-TF/AH
d 1/2 2 15/16 in
SY-WF/AH
d 3/4 2 7/16 in
YEL
FY
FY-FM/AH
d 1/2 2 3/16 in
FYT-FM/AH
d 1/2 2 3/16 in

SY-TF/AH
Cast-iron housing
Set screw locking
Wide inner ring
M-seal & flingers
Special aligning torque
Anti-rotation pin
Air handling quality grease
Shaft Pillow block

dia.
designation
da
Dynamic
capacity
C
in
lbf
in
Bolts
B
E
Min
E
Max
SY 12 TF/AH
SY 58 TF/AH
2150
1316
114
16
31532
4316
2732
SY 34 TF/AH
2860
11516
114
16
31532
4316
13
16
8
15
16
1
SY 1316 TF/AH*
SY 78 TF/AH
SY 1516 TF/AH
SY 1 TF/AH
3150
1716
518
11332
31116
1116
118
1316
114
SY 1116 TF/AH*
SY 118 TF/AH
SY 1316 TF/AH
SY 114 ATF/AH*
4390
11116
1916
21
414
114
1516
138
1716
SY 114 TF/AH
SY 1516 TF/AH*
SY 138 TF/AH
SY 1716 TF/AH
5740
1 8
25
1 32
11
112
SY 112 TF/AH
6910
11516
62932
12932
158
11116
134
SY 158 TF/AH
SY 11116 TF/AH
SY 134 TF/AH
7470
218
738
12932
13
11516
SY 11516 TF/AH
7900
214
218
2
2316
SY 2 TF/AH
SY 2316 TF/AH
9810
212
858
238
15
214
2716
SY 214 TF/AH
SY 2716 TF/AH
11900
234
91532
238
212
21116
SY 212 TF/AH
SY 21116 TF/AH
12900
1018
234
21516
SY 234 TF/AH
SY 21516 TF/AH
14900
314
11
(No. reqd)
lb
2
8
Mass
6 16
32
(2)-38
1.3
1.2
23
(2)-38
1.4
23
32
(2)-38
1.8
1.8
1.7
1.7
(2)-12
3.0
2.9
2.6
2.8
15
32
23364
41132
234
3732
32
16
16
(2)- 2
3.4
3.5
3.4
3.5
32932
1316
(2)-12
4.2
4732
1316
(2)-12
5.4
5.3
5.2
578
612
412
1932
(2)-58
6.3
638
718
1516
(2)-58
8.8
8.4
7116
71516
512
1916
(2)-58
10.6
10.3
2916
1532
71532
812
578
11116
(2)-34
14.0
12.6
22732
1932
61732
1116
11316
(2)-34
16.5
16.3
16
8
16
4 16
21
5 4
3 32
41516
534
5516
11
Note: Dimensions shown apply to YAR style insert bearing (TF arrangement). Consult SKF for dimensional information on additional types.
* Consult SKF for availability.
285
Ball bearing units

ConCentra air handling ball bearing units
SY-PF/AH
Cast-iron housing
ConCentra locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
Bearing
designation
in
Bearing
load rating
dynamic
C
lbf
Bolts
A
SY 1 PF/AH
SY 1316 PF/AH
YSP 205-100-2F/AH
YSP 206-103-2F/AH
3150
4350
1716
11116
518
6
114
138
SY 114 PF/AH
SY 138 PF/AH
YSP 207-104-2F/AH
YSP 207-106-2F/AH
5700
5700
178
178
6516 134
6516 134
1716
112
SY 1716 PF/AH
SY 112 PF/AH
YSP 207-107-2F/AH
YSP 208-108-2F/AH
5700
6900
178
11516
6516 134
678 178
11116
11516
SY 11116 PF/AH
SY 11516 PF/AH
YSP 209-111-2F/AH
YSP 210-115-2F/AH
7470
7900
218
214
738
8
178
218
13
2316
2716
SY 2316 PF/AH
SY 2716 PF/AH
YSP 211-203-2F/AH
YSP 212-207-2F/AH
9800
11800
212
234
858
912
238
238
21116
SY 21116 PF/AH
YSP 215-211-2F/AH
14000
1018 2916 118
2 16
15
SY 2 16 PF/AH
YSP 215-215-2F/AH
14800
286
E
Max
(No. reqd)
31116
414
4516
5
234
314
158
134
118
1316
(2)-38
(2)-12
41116
41116
514
514
31116
31116
178
178
114
114
(2)-12
(2)-12
41116
41516
514
534
31116
378
178
2116
114
1516
(2)-12
(2)-12
5516
578
6
612
414
412
2
218
138
138
(2)-12
(2)-58
638
7116
718
71516
5
512
214
2516
1716
112
(2)-58
(2)-58
712
812
578
238
112
(2)-34
(2)-34
in
1
1316
15
E
Min
3 4
11
1716
1916
13
8
8
4
4
4
4
16
8
15
16
2 16 1 4
6 2
2 2
1 8

SYH-TF/AH
Cast-iron housing
Low center height
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
SYH 12 TF/AH
SYH 58 TF/AH
2150
1316
114
31532
4316
2332
SYH 34 TF/AH
2860
114
114
31532
4316
13
16
8
15
16
1
SYH 1316 TF/AH*

SYH 78 TF/AH
SYH 1516 TF/AH
SYH 1 TF/AH
3150
1516
518
11332
31116
1116
118
1316
114
SYH
SYH
SYH
SYH
1116 TF/AH*
118 TF/AH
1316 TF/AH
114 ATF/AH*
4390
1916
1916
37
64
414
114
1516
138
1716
SYH
SYH
SYH
SYH
114 TF/AH
1516 TF/AH*
138 TF/AH
1716 TF/AH
5740
13
1 16
6 16
25
1 32
11
16
11
4 16
5 4
3 32
158
11116
134
SYH 158 TF/AH

SYH 11116 TF/AH
SYH 134 TF/AH
7470
2116
738
12932
13
16
5516
11516
SYH 11516 TF/AH
7900
2316
218
27
578
2
2316
SYH 2 TF/AH
SYH 2316 TF/AH
9810
2716
858
238
29
214
2716
SYH 214 TF/AH

SYH 2716 TF/AH
11900
21116
91532
238
234
SYH 234 TF/AH
14915
3516
11
22732
15
2 16
(No. reqd)
lb
2
8
Mass
16
2
15
32
21532
23
41132
258
25
3332
16
3964
(2)-38
1.3
1.3
32
(2)-38
1.4
32
(2)-38
1.8
1.8
1.7
1.7
(2)-12
3.0
2.9
2.9
2.8
16
(2)- 2
3.6
3.5
3.5
3.4
4532
1316
(2)-12
5.4
5.3
5.2
612
41532
1932
(2)-58
6.3
638
718
1516
(2)-58
8.5
8.0
7116
71516
5716
1916
(2)-58
11.5
10.4
1516
6916
1116
11316
(2)-34
16.3
32
32
SYH 21516 TF/AH
19
11
4
8
*Consult SKF for availability.

287
Ball bearing units

Pillow block / medium duty
SYM-TF/AH
Cast-iron housing
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
E
Min
E
Max
(No. reqd)
lb
1
1316
SYM 1 TF/AH
SYM 1316 TF/AH
4387
5737
11116
178
6
6516
1916
12532
1716
112
SYM 1716 TF/AH

SYM 112 TF/AH
6910
7470
218
218
738
738
134
12932
11116
134
SYM 11116 TF/AH

SYM 134 TF/AH
7900
214
218
11516
2316
SYM 11516 TF/AH

SYM 2316 TF/AH
9810
11900
212
234
858
91532
238
238
2316
SYMH 2316 TF/AH
11855
21116
91532
2716
212
SYM 2716 TF/AH

SYM 212 TF/AH
14000
21116
SYM 21116 TF/AH
14900
21516
3
SYM 21516 TF/AH

SYM 3 TF/AH
16400
21
414
41116
5
514
3732
32132
5
8
11
16
8
1
(2)-12
(2)-12
2.5
3.4
16
16
5516
5516
6
6
4732
4732
3
3
1316
1316
(2)-12
(2)-12
5.3
5.6
578
612
412
1932
(2)-58
7.0
6.7
16
638
7116
718
71516
5
512
1516
1916
(2)-58
(2)-58
8.8
11.7
238
7116
71516
5716
1916
(2)-58
10.3
101564
2916
11732
712
812
6132
1316
1916
(2)-34
15.0
15.4
312
12
15564
812
912
61732
1116
11316
(2)-34
23.8
312
12
3116
178
812
912
63132
1316
178
(2)-34
22.8
22.4
32
4
13
13
15
288
Mass
4
4
4
8

FY-TF/AH
Cast-iron flange
Four-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
1
Dynamic
capacity
C
Bolts
A
lbf
in
FY 12 TF/AH
FY 58 TF/AH
2150
218
25
FY 34 TF/AH
2860
338
212
13
3150
3 4
2 4
15
32
1 16
1 32
2 64
FY 1316 TF/AH*
FY 78 TF/AH
FY 1516 TF/AH
FY 1 TF/AH
1116
118
1316
114
FY 1116 TF/AH*
FY 118 TF/AH
FY 1316 TF/AH
FY 114 ATF/AH*
4390
414
314
33
64
1932
12132
31964
25
114
1516
138
1716
FY 114 TF/AH
FY 1516 TF/AH*
FY 138 TF/AH
FY 1716 TF/AH
5740
44164
358
33
64
15364
34764
112
FY 112 TF/AH
6910
518
35
64
2964
158
11116
134
FY 158 TF/AH
FY 11116 TF/AH
FY 134 TF/AH
7470
52564
418
35
64
11516
FY 11516 TF/AH
7900
558
438
19
32
2
2316
FY 2 TF/AH
FY 2316 TF/AH
9810
638
518
214
2716
FY 214 TF/AH
FY 2716 TF/AH
11900
678
558
43
212
21116
FY 212 TF/AH
FY 21116 TF/AH
12900
738
578
21
234
21516
FY 234 TF/AH
FY 21516 TF/AH
14900
734
16
8
15
16
7
(No. reqd)
lb
2
8
Mass
(4)-38
1
1
(4)-38
1.3
(4)- 16
1.9
1.9
2
1.7
32
(4)-716
2.7
2.5
2.4
2.7
53
64
(4)-12
3.2
3.6
3.5
3
41164
15
16
13
64
(4)-12
4.3
2964
41332
15
16
13
64
(4)-916
4.8
4.8
4.7
11116
22564
44164
1764
23
64
(4)-916
5.3
178
23564
5932
1732
11
32
(4)-58
7.9
7.5
64
2364
22932
558
11132
11
32
(4)-58
9.6
9
32
2116
25564
6116
1532
32
(4)-58
11.3
10.9
218
638
1316
16
(4)-34
15.7
14.8
64
16
59
1732
218
37
1532
11532
23164
64
12364
13364
11732
17
51
64
8
4
16
32
64
289
Ball bearing units

Flange/medium duty
FYM-TF/AH
Cast-iron flange
Four-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
FYM 1 TF/AH
4387
414
314
33
64
1932
12132
31964
25
32
(4)-716
2.6
1316
FYM 1316 TF/AH
5737
44164
358
33
64
12364
15364
34764
53
64
(4)-12
3.3
1716
FYM 1716 TF/AH
6910
518
21
32
11732
22964
41164
15
16
13
64
(4)-12
4.6
112
FYM 112 TF/AH
7470
52564
418
35
64
11732
2964
41332
15
16
13
64
(4)-916
5.3
11116
134
FYM 11116 TF/AH

FYM 134 TF/AH
7900
558
438
25
32
134
22564
44164
1764
23
64
(4)-916
5.7
5.7
11516
FYM 11516 TF/AH
9810
638
518
27
32
178
21732
5932
1732
11
32
(4)-58
8.2
2316
FYM 2316 TF/AH
11900
678
558
27
32
2532
22932
558
11132
11
32
(4)-58
9.7
2716
212
FYM 2716 TF/AH

FYM 212 TF/AH
14200
14000
738
578
11
16
214
618
1716
(4)-58
13.6
13.0
21116
FYM 21116 TF/AH
14900
734
218
638
1316
16
(4)-34
15.5
21516
3
FYM 21516 TF/AH

FYM 3 TF/AH
16400
734
2516
314
634
138
16
(4)-34
15.7
15.5
4
8
290
32
64

FYT-TF/AH
Cast-iron flange
Two-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
1
Dynamic
capacity
C
lbf
in
Bolts
Mass
FYT 12 TF/AH
FYT 58 TF/AH
2150
378
15
15
FYT 34 TF/AH
2860
41332
31732
16
13
16
8
15
16
1
FYT 1316 TF/AH*

FYT 78 TF/AH
FYT 1516 TF/AH
FYT 1 TF/AH
3150
478
32932
1116
118
1316
114
FYT 1116 TF/AH*

FYT 118 TF/AH
FYT 1316 TF/AH
FYT 114 ATF/AH*
4390
5916
41932
17
114
1516
138
1716
FYT 114 TF/AH

FYT 1516 TF/AH*
FYT 138 TF/AH
FYT 1716 TF/AH
5740
6 8
112
FYT 112 TF/AH
6910
158
11116
134
FYT 158 TF/AH

FYT 11116 TF/AH
FYT 134 TF/AH
11516
2
2316
(No. reqd)
lb
2
8
32
32
(2)-38
0.7
0.7
16
(2)-38
0.9
(2)-716
1.4
1.4
1.3
1.3
32
(2)-716
2.1
2.1
2.0
1.9
16
(2)- 2
2.9
2.9
2.8
2.8
11316
218
19
31
32
1932
238
1316
1716
234
1932
12132
318
25
16
11
13
32
8
16
16
32
5 8
16
1 32
1 16
3 8
13
634
52132
16
11732
2332
29
32
(2)-12
3.7
7470
7116
52732
11732
2332
414
29
32
(2)-916
4.3
4.3
4.2
FYT 11516 TF/AH
7900
7116
6316
25
32
12332
2932
4916
(2)-916
5.1
FYT 2 TF/AH
FYT 2316 TF/AH
9810
812
714
13
16
178
21532
1532
32
(2)-58
6.6
6.2
32
32
*Consult SKF for availability.

291
Ball bearing units

FYTM-TF/AH
Cast-iron flange
Two-bolt mounting
Set screw locking
Wide inner ring
M-seal & flingers
Anti-rotation pin
Shaft
dia.
da
Pillow block
designation
in
Dynamic
capacity
C
Bolts
A
lbf
in
Mass
(No. reqd)
lb
1716
FYTM 1716 TF/AH
6910
634
52132
16
11732
2332
29
32
(2)-12
3.9
112
FYTM 112 TF/AH
7470
7116
52732
11732
2332
414
29
32
(2)-916
4.5
11116
134
FYTM 11116 TF/AH

FYTM 134 TF/AH
7900
7716
6316
25
32
12332
2932
4916
(2)-916
5.4
5.4
11516
FYTM 11516 TF/AH
9810
812
714
13
16
178
21532
1532
32
(2)-58
6.7
292
32
32
Roller bearing
units
2716
NH - 118
5
3
4
2
1. Prefix:
F
3. Shaft size:
Four bolt base

(on SYE only)
2. Housing style:
4. Suffix:
SYE
Pillow block
ConCentra design
SYR
Pillow block
Held unit
SYT
Pillow block
Closed end (end cover supplied)
FYE
Square flange unit
PA
Housing with take-up frame

(for TRH)
FYR
Round flange unit
FYRP
Piloted flange unit
TBR
Center pull take-up unit
TRH
Take-up unit
TFT
Take-up frame only

(for SYR / SYE)
PA
Nomenclature
F SYE
5. Suffix/options/specials:
-3
Garter spring seal

(for collar mounted)
-18
Labyrinth seal
(for collar mounted)
-118
Labyrinth seal
(for ConCentra)
-xx
Travel code, inches

(length of travel for
take-up frames)
4. Suffix: (SYT only)

F
Unit with locating bearing
Unit with non-locating bearing
TS
Unit with labyrinth seals
Take-up frame only

(for TRH)
297
Roller bearing units

Introduction
TriGard seals as
standard. Garter spring
contact seals, labyrinth
seals, and end covers
also available.
Shaft ready assembly;

pre-assembled and
pre-greased.
High capacity SKF

with running or static
misalignment of 11/2.
Shaft attachment
collar mounting for
ease of installation
and holding power.
Controlled bearing fit

in the housing.
Available as a held or
free assembly.
Rugged one-piece cast-iron

housing. Available in a variety
of mounting styles.
Collar-mounted roller bearing unit
SKF roller bearing pillow blocks, flange blocks

and take-up units are offered with collar
mounting. SKF roller bearing pillow blocks and
take-up units are offered with ConCentra
mounting. Both are based on the SKF 22200
series spherical roller bearing. Fully assembled
and pre-greased, the units need no internal
bearing adjustments at assembly. This saves
time and eliminates the risk of bearing
contamination during assembly.
298
Roller bearing units offer many of the

advantages of the split housing series but with
the convenience of just slipping it on the shaft.
Running or static misalignment, free or held
assemblies, two- or four-bolt bases, cast iron
and a variety of seal options make the roller
bearing unit a preferred alternative to the
split housing.
Introduction
Shaft ready assembly;

pre-assembled and
pre-greased.
Patented multi-taper sleeve

uniformly clamps its inner ring
around the entire shaft
circumference and eliminates
mounting problems. The result:
The unit is centered with the
shaft and the inner ring secure,
preventing slipping or walking
on the shaft caused by a loose
fit between the bearing inner
ring and shaft.
Proven effective TriGard seals,

labyrinth seals and end covers
are also available.
Controlled bearing fit in

the housing. Available as
a held or free assembly.
Extreme ease of
mounting and
dismounting, only
tool necessary is a
hex head wrench.
Rugged one-piece
cast-iron housing.
ConCentra roller bearing unit
SKF has taken every effort to assure

that quality and trouble-free operation is
designed into each roller bearing unit. SKF
roller bearing units incorporate the world
leading SKF 22200 series spherical roller
bearing. Housing strength, housing bore
tolerance, machined base flatness and seals are
closely evaluated and tested, and are monitored
to assure optimum performance in a wide range
of applications. Some typical applications are:
Apron conveyors
Bucket elevators
Belt conveyors
Chain conveyors
Fans & blowers
Wastewater treatment equipment
Commercial laundry equipment
Offered in a range of shaft sizes from

17/16" to 415/16", SKF roller bearing units are
a convenient, economical choice to your
mounted bearing solution.
299

Introduction
Collar-mounted roller bearing unit

Roller bearing units are supplied completely
assembled with bearings, seals, and grease.
They are ready for installation right out of the
box and require no internal adjustment.
Bearings
The bearings used in SKF roller bearing units
are based on the high capacity SKF 22200
series spherical roller bearing. They can handle
heavy radial and axial loads, running and static
misalignment, and high operating temperatures.
Clearances in the bearing are preset; no
adjustment is required during mounting.
Mounting
Seals
Collar-mounted roller bearing units slide easily

onto the shaft and are locked in place with a
two set screw locking collar. The locking collar
keeps pressure on the set screws helping to
maintain the tight fit with the shaft. For added
holding power, the largest sizes are designed
with two locking collars, indicated in the
dimension tables. Mounting is quick and easy.
TriGard seal (standard)
Labyrinth seal
Housings
Bearing based on SKF 22200 series spherical

roller bearing. Heavy loads and running
misalignment.
There are a variety of housing styles in the SKF

roller bearing unit product line, including pillow
blocks, flange units and takeups. Pillow blocks
are made in two configurations: the SYE is
dimensionally interchangeable with competitor
"E" designs and the SYR is dimensionally
interchangeable with units such as the Dodge
S2000, Linkbelt PB22400, and Rexnord ZA
2000 series.
Table 1
Garter spring seal (suffix 3)
Set screw torque and permissible axial load

Shaft sizes
in
Set screw
(No.) size
1716 to 2316
2716 to 312
31116 to 4
4716 to 41516
(2)
(2)
(2)
(4)
8" - 24
2" - 20
5
8" - 18
5
8" - 18
3
1
Torque
in-lbs
250
620
1325
1325
Permissible axial load

lbs
515
900
1200
2400
End covers (suffix Y)
Grease
All roller bearing units are factory lubricated
with SKF LGEP2 grease or equivalent.
Table 2
Recommended shaft tolerances
Shaft diameter
Tolerance
Up to 11516"
2" to 41516"
Nominal to -0.0005"
Nominal to -0.0010"
Note: When the load is heavy, C/P < 8.3, a press fit
must be used. Consult SKF Applications Engineering.
300
Introduction
ConCentra roller bearing unit

ConCentra roller bearing units are supplied
completely assembled with bearings, seals, and
grease. They are ready for installation right out
of the box and require no internal adjustment.
ConCentra units can be used in the same
applications as collar-mounted roller bearing
units. The difference between the two types is
that the ConCentra unit mounts with a near
360 interference fit (see "Mounting", to the
right, and Product descriptions on following
page).
Mounting
Table 3
The ConCentra roller bearing unit uses a

patented multitapered sleeve arrangement,
making it easy to mount the bearing to the
shaft. This method provides nearly 360 of
interference fit, which does not offset the center
line of the shaft and helps reduce fretting.
Recommended shaft tolerances

Shaft diameter
Tolerance
Up to 112"
(Up to 38.10 mm)
+0.000" to -0.003"
(+0 to -76 m)
11116" to 212"
(42.86 to 63.50 mm)
+0.000" to -0.004"
(+0 to -101 m)
21116" to 4"
(68.26 to 101.60 mm)
+0.000" to -0.005"
(+0 to -127 m)
Seals
Housings
Bearings
The bearings used in ConCentra roller bearing
units are based on the high capacity SKF 22200
series spherical roller bearing. They can handle
heavy radial and axial loads, running and static
misalignment, and high operating temperatures.
Clearances in the bearing are preset; no
adjustment is required during mounting.
There are a variety of housing styles in the

ConCentra roller bearing unit product line
including pillow blocks and take-ups. Pillow
blocks are made in three configurations: the SYE
is dimensionally interchangeable with competitor
"E" designs, the SYR is dimensionally
interchangeable with units such as the Dodge
S2000, Linkbelt PB22400, and SKF collarmounted unit roller bearings; and the SYT is
dimensionally interchangeable with plummer
block assemblies of series SNL 5.
Tolerances
In normal cases shafts machined to tolerance h9
can be used. The cylindricity as defined in ISO
1101:1996 should be according to IT5/2. For
less demanding applications h10 and IT7/2 may
be satisfactory.
Grease
Labyrinth seal (suffix 118)
All roller bearing units are factory lubricated

with SKF LGEP2 grease or equivalent.
Grease characteristics
Base oil
Mineral
Thickener
Lithium
Application temperature
-4 to 230 F (-20 to 110 C)
NLGI
Viscosity at 100 F (40 C)
900 SUS (190 cSt)
*End covers (suffix Y)
*Consult SKF for Availability
212 F (100 C)
82 SUS (16 cSt)
301

SKF roller bearing units are available in a

variety of housing styles and two mounting
methods. These units are simple and economic
bearing arrangements combining the high load
capacity and self-aligning features of the SKF
spherical roller bearing with the convenience of
set screw mounting and a rugged cast-iron
housing. They come pre-greased and fully
assembled. Installation time is reduced and
there is no risk of bearing contamination during
assembly. Roller bearing units can accommodate
running or static misalignment of 112 and
can be supplied as free or held assemblies. All
units incorporate triple protection TriGard seals
as standard, but can also be supplied with
optional seals.
Collar-mounted units use a locking collar
design to firmly secure the bearing inner ring to
the shaft. The two set screws extended through
the inner ring of the bearing and lock into the
shaft. The elasticity of the locking collars
maintains pressure on the set screws helping to
maintain a secure fit to the shaft even in severe
power transmission applications. Mounting is
quick and easy. Slide the unit on the shaft, bolt
the housing securely to the mounting surface
and tighten the two set screws.
ConCentra units combine the advantages of
adapter mounting found in split pillow blocks
with the convenience of set screw mounting
found in collar mounted roller bearing units. The
result is a positive, near 360 interference fit
with the shaft. This is achieved with a unique
patented multi-tapered sleeve arrangement
developed by SKF. The shaft is held concentric to
the bore of the bearing resulting in reduced
fretting corrosion, good balance and low
vibration. Dismounting is just as easy. Loosen the
mounting set screws and tighten the
dismounting set screws until the multi-tapered
sleeve releases its grip, usually with a POP. No
need for cutting torches or other mechanical
devices. Downtime and shafting cost are saved.
ConCentra units are available in
SYE-N, FSYE-N, SYR-N, and SYT (metric) pillow
blocks as well as TBR-N and TRH-N take-up
housings. FYR and FYRP flange housing are
available on an application review basis. This is
due to the often limited access to the
dismounting set screws.
SYR/SYR-N
SYE/SYE-N
SYE/SYE-N
SYR/SYR-N
Cast-iron two-bolt base SYE and SYE-N unit

roller pillow blocks are available in shaft sizes
from 1716" to 312". Pages 306 and 307.
These SYR and SYR-N are cast-iron two-bolt

base unit roller pillow blocks. They are available
in shaft sizes ranging from 1716" to 4".
Pages 310 and 311.
FSYE/FSYE-N
FYE
FSYE/FSYE-N
FYE
The four-bolt base version of the SYE(-N) unit is

the FSYE(-N). They are available for shafts from
2716" to 41516" (ConCentra is available up to a 4";
please check SKF for availability). Pages 308
and 309.
FYE four-bolt flange cast-iron roller bearing

units are available in shaft sizes 1716" to 4".
These units typically occupy the bottom position
in vertical heat exchanger fan arrangements.
The SKF spherical roller bearing provides low
vibration, quiet running performance. Page 313.
SYT
The SYT is a two-bolt base, cast-iron pillow
block that is dimensionally interchangeable
with metric split plummer block housings. Only
available with ConCentra insert bearings and
metric shaft diameters 35 mm - 75 mm.
Page 312.
SYT
302
FYR
FYRP
FYR
FYRP
FYR cast-iron flange unit roller bearings support

rotating shafts through walls, bulkheads, or
other flat surfaces. The two smallest sizes
mount to the surface with three bolts; all other
sizes use four mounting bolts. They are available
for shaft sizes from 1716" to 4". These units rely
on the mounting bolts for location and load
carrying (FYR-N available on application review).
Page 314.
These piloted flange cast-iron flange units,

available for shaft sizes from 1716" to 4", have
a machined extension on one side to fit into a
precisely machined bulkhead opening. This
provides additional location and support to the
unit. All piloted flange units are supplied in
four-bolt mounting arrangements (FYRP-N
available on application review). Page 315.
TFT
TFT
TFT top mount take-up frames are designed for
use with SYR, SYR-N, SYE and SYE-N unit roller
pillow blocks. TFT assemblies are used primarily
for belt tensioning in conveyor applications. The
SYR blocks mount directly to the top of the
frame and are positioned by turning the
protected adjustment screw at either end of the
frame. TFT frames are available in travel lengths
ranging from 12" to 48" and they accommodate
SYR and SYR-N housings for shaft sizes from
1716" to 4". Pages 316 - 319.
303

Seal selection/collar-mounted roller bearing units
Table 4
Standard on all unit roller bearings

Features a double lip molded contact seal,
which rides on a ground surface of the
inner ring
Steel outboard trash guard protects the seal
and excludes larger contaminants
Provides positive contact even under
misaligned conditions
Permits 112 misalignment
Low frictional torque
Limited to 200 F maximum operating
temperature
Seal speed limits

Two-piece all metal labyrinth seal
provides for high operating speeds
Inboard flinger pressed on the inner ring
of the bearing helps retain grease and
exclude contaminants
Outboard stationary trash guard is pressed
into the housing and has close running tolerance with the inner ring of the bearing to
prevent the entrance of contaminants
Design permits 112 misalignment
No frictional torque
No temperature limitation

Features one-piece molded nitrile rubber seal
pressed into the housing bore
Provides greater grease retention and sealing
protection because stainless steel garter
spring holds seal lip firmly to the ground
inner ring
Provides good protection in moist
environment
temperature

Steel end covers are simply pushed into
position in the housing bore
Provides additional sealing and protection
against exposed shaft ends
304
Shaft size
in
TriGard
rpm
Labyrinth
Garter spring
1716
112
2800
2800
5300
5300
1700
1700
11116
134
2650
2650
4700
4700
1600
1600
11516
2
2400
2400
4250
4250
1450
1450
2316
2150
3800
1300
2716
212
1800
1800
3250
3250
1100
1100
21116
234
21516
3
1600
1600
1600
1600
2800
2800
2800
2800
950
950
950
950
3716
312
1300
1300
2200
2200
800
800
31116
31516
4
1200
1200
1200
2000
2000
2000
700
700
700
4716
412
1100
1100
N/A
N/A
N/A
N/A
41516
900
N/A
N/A
Seal selection/ConCentra roller bearing units
Table 5
Standard on all unit roller bearings

Features a double lip molded contact
seal, which rides on a ground surface of
the mounting and dismounting collars
Steel outboard trash guard protects the
seal and excludes larger contaminants
Low frictional torque
temperature
Seal speed limits

Three-piece all metal labyrinth seal
allows operation at the basic bearing
grease speed rating
Inboard flinger pressed on the inner ring
of the bearing helps retain grease
Outboard flinger pressed on the inner
ring flings contaminants away from the
seal opening
A stationary trash guard, positioned between
the two flingers, is pressed into the housing
and helps create a difficult path labyrinth to
prevent the ingress of contaminants
No frictional torque
No temperature limitation
Shaft size
in
TriGard
rpm
Labyrinth
1716
112
4000
4000
5600
5600
11116
134
3700
3700
5300
5300
11516
2
3500
3500
5000
5000
2316
3250
4500
2716
212
2900
2900
3800
3800
21116
234
21516
3
2600
2600
2600
2600
3400
3400
3400
3400
3716
312
2200
2200
2600
2600
31516
4
2000
2000
2200
2200
Steel end covers are simply pushed into

position in the housing bore
Provides additional sealing and protection
against exposed shaft ends
305

Pillow block / collar-mounted
SYE
Type E, ZEP EPB22400H equivalent
Cast-iron housing
2-bolt base
Self-aligning
Held or free
TriGard seal
How to order
SYE 2716
Option
Specify
Held unit
Closed end
Garter spring seal
Labyrinth seal
SYE
SYE
SYE
SYE
2716 H
2716 Y
2716-3
2716-18
For shaft diameter tolerances see page 300; for bearing information see page 320; for other seal speed limits see page 304.
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
1716
SYE 1716
16 600
2800
8.0
178
738
218 118
512
112
11116
SYE 112
SYE 11116
16 600
17 300
2800
2650
8.0
9.3
218
778
238 114
612
134
11516
2
SYE 134
SYE 11516
SYE 2
17 300
19 000
19 000
2650
2400
2400
9.3
10.5
10.5
214
878
212 1516
714
2316
SYE 2316
22 400
2150
13.5
212
958
258 112
2716
212
SYE 2716
SYE 212
33 300
1800
18.5
18.0
234 1012
21116
234
21516
3
SYE
SYE
SYE
SYE
35 500
1600
25.5
25.0
24.0
23.5
318 12
3716
312
SYE 3716
SYE 312
56 900
1300
35.5
35.5
334 14
358 214
21116
234
21516
3
Bolts
(No.
reqd)
A
306
Mass
lbs
E
Max
E
Min
in
in
378
22732 1
234
(2)-12
414
23132 1
234
(2)-12
634
412
3532
278
(2)-58
712
31132 118
318
(2)-58
278 158
834
814
51116 31932 114
338
(2)-58
178
934
914
118
6516
32932 114
358
(2)-34
11516
101116
1516
712
4716
1716 4132 (2)-78
Pillow block / ConCentra

SYE-N
Type E, ZEP, EPB22400H equivalent
Cast-iron housing
2-bolt base
Self-aligning
Held or free
TriGard seal
How to order
SYE 2716 N
Option
Specify
Held unit
Closed end
Labyrinth seal
SYE 2716 NH
SYE 2716 NY
SYE 2716 N-118
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
1716
SYE 1716 N
22 900
4000
8.0
178
738
218
118
512
112
11116
SYE 112 N
SYE 11116 N
22 900
20 200
4000
3700
8.0
9.3
218
778
238
114
612
134
11516
2
SYE 134 N
SYE 11516 N
SYE 2 N
20 200
21 700
21 700
3700
3500
3500
9.3
10.5
10.5
214
878
212
1516
714
2316
SYE 2316 N
30 100
3250
13.5
212
958
258
112
2716
212
SYE 2716 N
SYE 212 N
43 400
2900
18.5
18.5
234
1012
278
21116
234
21516
3
SYE
SYE
SYE
SYE
47 700
2600
25.5
25.0
24.0
23.5
318
12
3716
312
SYE 3716 N
SYE 312 N
65 200
2200
35.5
334
14
21116 N
234 N
21516 N
3N
Mass
Bolts
(No.
reqd)
A
lbs
E
Max
E
Min
in
in
378
(2)-12
414
(2)-12
634
412
(2)-58
712
(2)-58
158
834
814
51116
(2)-58
178
934
914
118
6516
(2)-34
358
214
11516
101116
1516
712
(2)-78
307

FSYE
Type E, ZEP, EPB22400FH equivalent
Cast-iron housing
4-bolt base
Self-aligning
Held or free
TriGard seal
How to order
FSYE 2716
Option
Specify
Held unit
Closed end
Garter spring seal
Labyrinth seal
FSYE
FSYE
FSYE
FSYE
2716 H
2716 Y
2716-3
2716-18
FSYE 2716 thru FSYE-4 supplied with single locking collar only
FSYE 4716 thru FSYE-41516 supplied with double locking collar only
Shaft
dia.
da
Designations
Pillow block
unit
in
2716
212
FSYE 2716
FSYE 212
21116
234
21516
3
FSYE
FSYE
FSYE
FSYE
3716
312
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
lbs
rpm
Mass
Bolts
(No.
reqd)
A
lbs
E
Max
E
Min
in
in
1800
19.0
18.5
234 1012 312 158
834
814
178 1
51116 31932 114
338
(4)-58
35 500
1600
25.5
25.5
24.0
24.0
318 12
978
918
218 118
6516
32932 114
358
(4)-58
FSYE 3716
FSYE 312
56 900
1300
36.5
334 14
412 214
712
4716
1716 4132
31116
31516
4
FSYE 31116
FSYE 31516
FSYE 4
69 900
1200
50.5
49.5
49.5
414 1514 412 2716 13
12
214 138
8916
478
158
4716
412
FSYE 4716
FSYE 412
91 700
1100
71.0
434 1658 458 234
1378
1318
212 114
938
43132
(4)-34
41516
FSYE 41516
123 000
900
100.0
512 1812 518 3
1578
1518
234 138
1078
51732
(4)-78
21116
234
21516
3
33 300
308
178
11716 10916 238 1516
(4)-34
41932 (4)-34

FSYE-N
Type E, ZEP, EPB22400FH equivalent
Cast-iron housing
4-bolt base
Self-aligning
Held or free
TriGard seal
How to order
FSYE 2716 N
Option
Specify
Held unit
Closed end
Labyrinth seal
FSYE 2716 NH
FSYE 2716 NY
FSYE 2716 N-118
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
lbs
in
2716
212
FSYE 2716 N
FSYE 212 N
43 400
2900
19.0
234
1012
312
158
834
814
178
51116
(4)-58
21116
234
21516
3
FSYE
FSYE
FSYE
FSYE
47 700
2600
25.5
25.5
24.0
24.0
318
12
178
978
918
218
118
6516
(4)-58
3716
312
FSYE 3716 N
FSYE 312 N
65 200
2200
36.5
334
14
412
214
11716
10916
238
1516
712
(4)-34
31116
31516
4
FSYE 31116 N
FSYE 31516 N
FSYE 4 N
81 000
2000
50.5
49.5
49.5
414
1514
412
2716
13
12
214
138
8916
(4)-34
21116 N
234 N
21516 N
3N
Mass
Bolts
(No.
reqd)
A
E
Max
E
Min
in
309

SYR
ZA, PB24400H, S2000 equivalent
Cast-iron housing
2-bolt base
Self-aligning
Held or free
TriGard seal
How to order
SYR 2716
Option
Specify
Held unit
Closed end
Garter spring seal
Labyrinth seal
SYR
SYR
SYR
SYR
2716 H
2716 Y
2716-3
2716-18
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
1716
112
SYR 1716
SYR 112
16 600
2800
7.0
178
678
218
1316
5516
41116 378
21316
234
(2)-12
11116
134
SYR 11116
SYR 134
17 300
2650
8.1
218
738
238
1516
51316
5316
21516
278
(2)-12
11516
2
SYR 11516
SYR 2
19 000
2400
9.2
9.1
214
838
238
138
6916
51516 4916
21516
278
(2)-58
2316
SYR 2316
22 400
2150
12.0
212
878
238
158
7116
6716
3316
118
318
(2)-58
2716
212
SYR 2716
SYR 212
33 300
1800
16.0
234
914
21116 134
7716
61316 51116 3716
114
338
(2)-58
21116
234
21516
3
SYR
SYR
SYR
SYR
35 500
1600
22.0
22.0
21.0
21.0
314 10716
21116 214
8716
71316 6716
31116
114
358
(2)-34
3716
312
SYR 3716
SYR 312
56 900
1300
31.5
334 13
3316
214
1034
914
712
4332
1716 4132
(2)-78
31116
31516
4
SYR 31116
SYR 31516
SYR 4
69 900
1200
44.5
43.5
43.5
418 1414
31732 212
1134
8716
42132
158
(2)-1
21116
234
21516
3
Bolts
(No.
reqd)
A
310
Mass
lbs
E
Max
E
Min
in
in
10
414
41932

SYR-N
ZA, PB22400H, S2000 equivalent
Cast-iron housing
2-bolt base
Self-aligning
Held or free
TriGard seal
How to order
SYR 2716 N
Option
Specify
Held unit
Closed end
Labyrinth seal
SYR 2716 NH
SYR 2716 NY
SYR 2716 N-118
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
1716
112
SYR 1716 N
SYR 112 N
22 900
4000
7.0
178
678
2116
1316
5516
41116
378
21132
(2)-12
11116
134
SYR 11116 N
SYR 134 N
20 200
3700
8.1
218
738
218
1516
51316
5316
414
21132
(2)-12
11516
2
SYR 11516 N
SYR 2 N
21 700
3500
9.2
214
838
2516
138
6916
51516
4916
21132
(2)-58
2316
SYR 2316 N
30 100
3250
12.0
212
878
238
158
7116
6716
21132
(2)-58
2716
212
SYR 2716 N
SYR 212 N
43 400
2900
16.0
234
914
21116
134
7716
61316
51116
23764
(2)-58
21116
234
21516
3
SYR
SYR
SYR
SYR
47 700
2600
22.0
22.0
21.0
21.0
314
10716
21116
214
8716
71316
6716
23764
(2)-34
3716
312
SYR 3716 N
SYR 312 N
65 200
2200
31.5
334
13
3316
214
1034
914
712
3532
(2)-78
31116
31516
4
SYR 31116 N
SYR 31516 N
SYR 4 N
81 000
2000
44.5
43.5
43.5
418
1414
31732
212
1134
8716
338
(2)-1
21116 N
234 N
21516 N
3N
Mass
Bolts
(No.
reqd)
A
lbs
E
Max
E
Min
in
in
10
311

SYT
SNL 5 equivalent (metric)
Cast-iron housing
2-bolt base
Self-aligning
Held or free
TriGard seal
Location for monitoring sensors
How to order
SYT 55
Option
Specify
Free unit
Held unit
Labyrinth seal-free
Labyrinth seal-held
SYT 55
SYT 55
SYT 55
SYT 55
L
F
LTS
FTS
Locating bearing
Shaft
dia.
da
Designation
unit
Bearing basic
load ratings
dynamic
C
Speed
rating
TriGard
seal
Mass
Dimensions
A
Grub
screw
size
H1
H2
N1
mm
r/min
kg
mm
35
SYT 35
76 500
2 700
3.40
60
110
60
25
170
205
20
15
12
M6
40
SYT 40
102 000
2 500
3.50
60
114
60
25
170
205
20
15
12
M6
45
SYT 45
90 000
2 300
3.80
60
116
60
25
170
205
20
15
12
M6
50
SYT 50
96 500
2 150
4.80
70
129
70
28
210
255
24
18
16
M6
55
SYT 55
134 000
2 000
5.40
70
135
70
30
210
255
24
18
16
M6
60
SYT 60
163 000
1 850
7.00
80
150
80
30
230
275
24
18
16
M8
65
SYT 65
193 000
1 800
8.00
80
157
80
30
230
280
24
18
18
M8
70
SYT 70
208 000
1 650
10.6
90
177
95
32
260
315
28
22
20
M8
75
SYT 75
212 000
1 600
11.3
90
182
95
32
260
320
28
22
20
M8
312
Flange block / collar-mounted

FYE
Type E, EFR
Cast-iron housing
4-bolt
Self-aligning
Held or free
TriGard seal
FYE 2716
How to order
Option
Specify
FYE 2716 H
FYE 2716 Y
FYE 2716-3
FYE 2716-18
Held unit
Closed end
Garter spring seal
Labyrinth seal
Shaft
dia.
da
Designations
Flange block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
lbs
in
1716
FYE 1716
16600
2800
7.2
458
312
214
22732
234
1332
112
11116
FYE 112
FYE 11116
16600
17300
2800
2650
10
10
538
418
2516
22932
3132
234
278
1532
134
11516
2
FYE 134
FYE 11516
FYE 2
17300
19000
19000
2650
2400
2400
11
512
414
214
23132
278
2316
FYE 2316
22400
2150
13.5
614
434
238
3732
118
2716
212
FYE 2716
FYE 212
33300
1800
17.3
17.1
678
538
234
31532
21116
234
21516
3
FYE
FYE
FYE
FYE
35500
1600
28.5
28.3
27.2
27
758
1116
234
3716
312
FYE 3716
FYE 312
56900
1300
40.6
40.1
834
118
31116
31516
4
FYE 31116
FYE 31516
FYE 4
69900
1200
64.1
69.1
68.1
934
734
114
21116
234
21516
3
Mass
Bolt
square
A
Bolts
(No.
reqd)
Bolt
Hole
Db
in
in
32
(4)-12
32
(4)-12
1332
32
(4)-12
318
1732
32
(4)-12
11
114
338
11132
32
(4)-58
11
378
114
358
112
(4)-34
13
3516
414
1716
4132
12132
32
(4)-34
13
312
41316
158
41932
12732
32
(4)-78
15
16
16
16
16
16
16
16
16
313

Flange block / collar-mounted
FYR
ZB, FB22400H, S2000 equivalent
Cast-iron housing
3-bolt or 4-bolt
Self-aligning
Held or free
TriGard seal
How to order
FYR 2716
Option
Specify
Held unit
Closed end
Garter spring seal
Labyrinth seal
FYR
FYR
FYR
FYR
2716 H
2716 Y
2716-3
2716-18
FYR 1716 and 112 have

three mounting holes ? 120
Shaft
dia.
da
Designations
Pillow block
unit
Bearing
basic load
rating
dynamic
C
TriGard
speed
limit
in
lbs
rpm
1716
112
FYR 1716
FYR 112
16 600
2800
8.5
8.4
614
2116 278
11116
134
FYR 11116
FYR 134
17 300
2650
10.5
11.0
634
512
214
11516
2
FYR 11516
FYR 2
19 00
2400
11.0
10.5
534
214
2316
FYR 2316
22 400
2150
13.5
734
638
238
2716
212
FYR 2716
FYR 212
33 300
1800
17.5
818
634
21116
234
21516
3
FYR
FYR
FYR
FYR
35 500
1600
27.0
27.0
26.0
26.0
912
3716
312
FYR 3716
FYR 312
56 900
1300
38.0
1118
31116
31516
4
FYR 31116
FYR 31516
FYR 4
69 900
1200
53.0
52.0
52.0
21116
234
21516
3
Mass
A
lbs
314
Bolt
circle
B
Bolts
(No.
reqd)
Bolt
hole
Db
in
in
in
378 1
234
1332
8 (3)-12
13
16 412 1
278
1332
8 (4)-12
13
16 434 1
278
1332
8 (4)-12
314
15
16 518 118
318
1732
8 (4)-58
11
15
16 2916 312
15
338
11132
8 (4)-58
11
778
15
16 278
358
11532
4 (4)-34
13
912
118
3116 4932
12132
4 (4)-34
13
1258 1034
118
312
41932 12732
4 (4)-78
15
378
16 534 114
1316
658 114
1316
758 1716 4132
42732 1716
838 158
16
16
16
16
16
16
16
16
Piloted flange / collar-mounted

FYRP
ZBR, FCB22400H, S2000, Type E equivalent
Cast-iron housing
4-bolt base
Self-aligning
Held or free
TriGard seal
How to order
FYRP 2716
Option
Specify
Held unit
Closed end
Garter spring seal
Labyrinth seal
FYRP
FYRP
FYRP
FYRP
2716 H
2716 Y
2716-3
2716-18
Shaft
dia.
da
Designations
Piloted flange
unit
Bearing
TriGard
basic load speed
rating
limit
dynamic
C
Mass
in
lbs
rpm
lbs
1716
112
FYRP 1716
FYRP 112
16 600
2800
6.3
514
438
214
25764 12564
11116
134
FYRP 11116
FYRP 134
17 300
2650
7.8
7.7
618
518
212
3532
11932
11516
2
FYRP 11516
FYRP 2
19 000
2400
8.2
638
538
16 212
3532
11932
2316
FYRP 2316
22 400
2150
9.9
718
16 2916 3516
12132
2716
212
FYRP 2716
FYRP 212
33 300
1800
14.0
13.5
758
612
11116
21116
234
21516
3
FYRP
FYRP
FYRP
FYRP
35 500
1600
20.5
20.5
19.5
19.5
834
712
11
3716
312
FYRP 3716
FYRP 312
56 900
1300
29.5
29.0
1014
858
3316 4732
31116
31516
4
FYRP 31116
FYRP 31516
FYRP 4
69 900
1200
41.0
40.0
40.0
1078
938
358
21116
234
21516
3
Bolt
circle
A
J1)
Bolts
(No.
reqd)
Bolt
hole
Db
in
in
64 (4)-38
13
in
2
258
16 318
312
32932 2132
11516
41316 21332
23
4 3.625 1
234
27
278
278
23
5.000 118 318
16
13
5.500 114 338
15
32
16 114 6.375 114 358
13
16
17
32
32
8 4.250 1
8 4.500 1
32 1
16 1
13
1116
114 7.375 1716 4132
8.125 158 41932
64
13
16
32 (4)-716
32 (4)-716
32
15
32
16 (4)-12
(4)-12
17
32 (4)-58
21
16 (4)-34
25
32 (4)-34
25
16
32
32
32
32
1.) O.D. tolerance of the FYRP unit pilot diameter (J) dimension is 0.000 in. to 0.002 in.
315

Take-up frames / top mount
TFT (Pillow block not included)
SYE, SYE-N, SYR, SYR-N
Top mount
Steel frame
Protected screw
Specification:
2716" shaft, 18" travel,

SYE held pillow block
How to order
Frame
Pillow block
TFT 03-18
SYE 2716 H
Shaft
dia.
da
Designations
Basic frame
in
Pillow block
1716
Collarmounted
ConCentra
SYE 1716
SYE 1716 N
SYE 112
SYE 11116
SYE 112 N
SYE 11116 N
SYE 134
SYE 11516
SYE 2
SYE 134 N
SYE 11516 N
SYE 2 N
SYE 2316
SYE 2316 N
2716
212
SYE 2716
SYE 212
SYE 2716 N
SYE 212 N
21116
234
21516
3
SYE
SYE
SYE
SYE
112
11116
134
11516
2
TFT 01 XX
TFT 02 XX
2316
TFT 03 XX
3 16
312
TFT 04 XX
TFT 06 XX
SYE 3 16
SYE 312
316
21116
234
21516
3
SYE
SYE
SYE
SYE
21116 N
234 N
21516 N
3N
SYE 3 16 N
SYE 312 N
Travel
and
code no.
Mass
in
lb
12
18
24
30
36
30.0
35.0
40.0
50.0
56.0
18
24
30
36
125
130
135
140
18
24
30
36
48
180
190
205
215
235
18
24
30
36
48
195
210
215
230
245

SYE, SYE-N, SYR, SYR-N
Top mount
Steel frame
Protected screw

SYE held pillow block
Specification:
How to order
Frame
Pillow block
Shaft
dia.
da
Travel
and
code no.
in
in
in
1716
112
11116
134
11516
2
2316
7
2 16
212
21116
234
21516
3
3 16
312
Bolt size
(2 reqd)
C
Frame
hole
C1
in
in
in
in
178
2-13 x 212
12
18
24
30
36
31
218 37
43
49
55
1
2 4
18
24
30
36
212 4114
4714
5314
234 5914
18
24
30
36
48
318
4414
5014
5614
6214
7414
334
46
52
58
64
76
18
24
30
36
48
16
2-13 x 212
8-11 x 3
114
11
16
1516
8-11 x 314
8-9 x 4
in
16
15
16
212 1
514 11
178
114
1414
214
4314
4914
5514
6114
7314
114
16
158
13
29
35
41
47
53
4112
4712
5312
5912
7112
16
11
4-10 x 312
3834
4434
5034
5634
112
8-11 x 3
Bolt
dia.
K
118
9
Rod
dia.
G
6 4 13 4
L
Max
TFT 03-18
SYE 2716 H
L
Min
in
6
512
612
714
634
712
918
812
912
4
91316
1114
3
578
10 8
434
6 8
834
814
934
914
1134
812 13716
11516
101116
1258
812 1412
111516
317

SYR, SYR-N
Top mount
Steel frame
Protected screw
Specification:

SYR held pillow block
How to order
Frame
Pillow block
TFT 03-18
SYR 2716 H
Shaft
dia.
da
Designations
Basic frame
in
Pillow Block
1716
112
Collarmounted
SYR 1716
SYR 112
ConCentra
SYR 1716 N
SYR 112 N
TFT 01 XX
11
11
11
SYR 1 16
SYR 134
SYR 1 16 N
SYR 134 N
SYR 11516
SYR 2
SYR 11516 N
SYR 2 N
SYR 2316
SYR 2316 N
2716
212
SYR 2716
SYR 212
SYR 2716 N
SYR 212 N
21116
234
21516
3
SYR
SYR
SYR
SYR
1 16
134
11516
2
TFT 02 XX
2316
TFT 03 XX
3 16
312
11
3 16
31516
TFT 04 XX
TFT 06 XX
TFT 07 XX
SYR 3 16
SYR 312
11
SYR 3 16
SYR 31516
318
21116
234
21516
3
SYR
SYR
SYR
SYR
21116 N
234 N
21516 N
3N
SYR 3 16 N
SYR 312 N
11
SYR 3 16 N
SYR 31516 N
Travel
and
code no.
Mass
in
lb
12
18
24
30
36
30.0
35.0
40.0
50.0
56.0
18
24
30
36
125
130
135
140
18
24
30
36
48
180
190
205
215
235
18
24
30
36
48
195
210
215
230
245
18
24
30
36
48
330
340
360
370
390

SYR, SYR-N
Top mount
Steel frame
Protected screw

SYR held pillow block
Specification:
How to order
Frame
Pillow block
Shaft
dia.
da
Travel
and
code no.
in
in
in
1716
112
11116
134
11516
2
2316
2716
212
21116
234
21516
3
12
18
24
30
36
2 8
Frame
hole
C1
in
in
in
in
31
37
43
49
55
1316
1
2-13 x 212
18
24
30
36
212 4114
4714
5314
234 5914
18
24
30
36
48
318
4414
5014
5614
6214
7414
334
46
52
58
64
76
418
50
56
62
68
80
31116
31516
18
24
30
36
48
16
1 16
3 16
312
214
18
24
30
36
48
178
Bolt size
(2 reqd)
C
11
8-11 x 3
16
11
5
4-10 x 312
8-9 x 4
1-8 x 412
16
15
16
1116
in
29
35
41
47
53
L
Max
in
L
Min
in
918
7
212 1
514 11
11
4 16
812
778
578
51516
912
91316
214
4112
4712
5312
5912
7112
114
1414
11
71316
1134
812 13716
214
4314
4914
5514
6114
7314
114
16
1318
914
1258
812 1412
212
4714
5314
5914
6514
7714
114
20
11
1034
1458
812 15716
714
1 4
13
8-11 x 3 4
3834
4434
5034
5634
16
Bolt
dia.
K
138
158
8-11 x 3
Rod
dia.
G
TFT 03-18
SYR 2716 H
1114
1
614 1314
958
6716
1038
658
434
15
11 16
319

Insert bearings / collar-mounted
4762(00)B and 4762(00)B-VSB series
Table 19A
SKF unit roller insert bearings are produced as standard
with radial internal clearance within the limits shown in
the table below
Shaft sizes
Internal clearance
in
in
min
.0010
.0012
.0014
.0018
.0024
.0028
.0035
1716 - 112
11116 - 2
2316 - 212
21116 - 3
3716 - 4
4716 - 412
41516
Shaft
dia.
da
max
- .0020
- .0022
- .0026
- .0031
- .0039
- .0047
- .0057
mm
min
.025
.030
.035
.045
.060
.070
.090
Designation
in
mm
mm in
max
- .050
- .055
- .065
- .080
- .100
- .120
- .145
Bearing
basic load
rating
dynamic
C
Series 4762B
Series 4762B-VSB
Shaft sizes
1716 thru 4
Static
C0
lb
B1
B2
Shaft sizes
4716 thru 41516
d1
Set
screw
size
Mass
Calculation
factors
in
lb
d2
in
1716
112
476208B-107
476208B-108
80
23
234
16 600
18 300
.219
1.908
238
11116
134
476209B-111
476209B-112
85
23
278
17 300
19 800
.219
2.157
258
11516
2
476210B-115
476210B-200
90
23
278
19 000
22 500
.219
8 21532 2.357
278
2316
476211B-203
100
25
318
22 400
26 500
.219
118
2716
212
476213B-207
476213B-208
120
31
338
33 300
41 100
.219
21116
334
21516
3
476215B-211
476215B-212
476215B-215
476215B-300
130
31
358
35 500
46 800
.219
3716
312
476218B-307
476218B-308
160
40
4132
56 900
76 400
.219
31116
31516
4
476220B-311
476220B-315
476220B-400
180
46
41932 69 900
93 300
.328
4716
412
476222B-407VSB
476222B-408VSB
200
53
618
91 700
126 000
.328
41516
476226B-415VSB
230
64
658
123 000
180 000
.438
320
Y1
Y2
Y0
2.50
8-24 x 12 2.45
0.28 2.4 3.6 2.5
2.75
8-24 x 12 2.70
0.26 2.6 3.9 2.5
2.90
8-24 x 12 2.80
0.24 2.8 4.2 2.8
314
0.24 2.8 4.2 2.8
114
0.24 2.8 4.2 2.8
114
412
0.22 3
1716 518
0.23 2.9 4.4 2.8
31516 4.650
158
518
5.029
3116 618
0.25 2.7 4
558
5.819
3516 678
0.26 2.6 3.9 2.5
8 238
8 238
4 22332 2.600
8 21516 3.088
8 3116
3.491
8 31532 4.224
8-24 x 12 3.90
2-20 x 34 6.75
2-20 x 78 9.35
2-20 x 78 13.5
8-18 x 1
19.5
8-18 x 78 29.5
8-18 x 78 46.5
4.6 2.8
0.24 2.8 4.2 2.8
2.5
Insert bearings / ConCentra

BSYB 4752(00) Series
Table 19B
SKF unit roller insert bearings are produced as standard
with radial internal clearance within the limits shown in
the table below
Designation
in (mm)
Bearing
basic load
rating
dynamic
C
mm
mm in
Internal clearance
in
in
min
1716 - 112
11116 - 2
2316 - 212
21116 - 3
3716 - 4
3mm allen wrench

supplied with each unit
Shaft
dia.
da
Shaft sizes
Static
C0
lb
d2
B1
in
mm
in
.0020
.0024
.0030
.0037
.0043
max
m
min max
mm
min
.0026
.0031
.0037
.0047
.0055
50 - 65
60 - 80
75 - 95
95 - 120
110 - 140
.050
.060
.075
.095
.110
max
-
.065
.080
.095
.120
.140
Mass
No.
mounting
screws
(M6X1)
Calculation
factors
lb
qty
Y1
Y2
Y0
(35)
BSYB 475207
72
23
21132 17 200
16 500
.219
57
2964
1.75
0.31
2.2
3.3
2.2
1716
112
(40)
BSYB 475208-107
BSYB 475208-108
BSYB 475208
80
23
21132 22 900
22 000
.219
62
218
1.85
0.28
2.4
3.6
2.5
11116
134
(45)
BSYB 475209-111
BSYB 475209-112
BSYB 475209
85
23
21132 20 200
19 800
.219
68
218
2.42
0.26
2.6
3.9
2.5
11516
2
(50)
BSYB 475210-115
BSYB 475210-200
BSYB 475210
90
23
21132 21 700
22 500
.219
72
218
2.42
0.24
2.8
4.2
2.8
2316
(55)
BSYB 475211-203
BSYB 475211
100
25
21132 30 100
30 800
.219
77.56
2732
2.98
0.24
2.8
4.2
2.8
(60)
BSYB 475212
110
23
23764 36 700
38 900
.219
85
21132
4.81
0.24
2.8
4.2
2.8
2716
212
(65)
BSYB 475213-207
BSYB 475213-208
BSYB 475213
120
31
23764 43 400
41 100
.219
87
22964
4.85
0.24
2.8
4.2
2.8
(70)
BSYB 475214
125
31
23764 46 800
51 300
.219
95
21532
5.95
0.23
2.9
4.4
2.8
21116
234
21516
3
(75)
BSYB
BSYB
BSYB
BSYB
BSYB
475215-211
475215-212
475215-215
475215-300
475215
130
31
2 64 47 700
54 000
.219
97
2 64
5.29
4
4
5
4
4
0.22
4.6
2.8
3716
312
BSYB 475218-307
BSYB 475218-308
160
40
3964
65 200
76 400
.219
113
25364
10.88
0.23
2.9
4.4
2.8
31116
31516
4
BSYB 475220-311
BSYB 475220-315
BSYB 475220-400
180
46
32564 81 000
93 300
.328
125
3116
15.95
0.24
2.8
4.2
2.8
37
29
321
Notes
322
Split pillow blocks

(inch series)
Nomenclature
_ SAF _ 22634 TA
1
2
1. Prefix:
F
3
4
4. Housing designation:
Cast-iron
Four-bolt base
(when optional)
Basic bearing series
Mounting method
13(00)
Cast-steel
13(00)
Cylindrical
15(00)
12(00)K
Adapter
16(00)
2. Housing style:
13(00)K
Adapter
222(00)
222(00)
222(00) CC/W33
Cylindrical
223(00)
223(00)
223(00) CC/W33
Cylindrical
Standard pillow block
225(00)
225(00)
222(00) CC/W33
Adapter
Heavy duty series
226(00)
226(00)
223(00) CC/W33
Adapter
Inch dimensions
230(00)KA
230(00) CC/W33
Adapter
C22(00)
C22(00)
Cylindrical
C23(00)
C23(00)
Cylindrical
C25(00)
C22(00)K
Adapter
C26(000
C23(00)K
Adapter
C30(00)KA
C30(00)K
Adapter
Triple ring seal
3. Material:
_
Cast-iron (standard)
Ductile-iron
Cast-steel
5. Suffix:
T
Taconite contact seal
TV
Taconite V-ring seal
TA or TVA
Taconite seal with button head grease fitting
TB or TVB
Taconite seal with giant button head grease fitting
One end closed (i.e.,supplied with end plug)
-11
Four-bolt base (when optional / cast steel SAFS only)
/ V Z###
Special feature / modification
-##
Special feature / modification
TLC
PosiTrac PlusTM seal
329
Split pillow blocks (inch series)

Introduction
SKF split pillow blocks are the most versatile

mounted assemblies and are designed for
extremely demanding applications. They can
accommodate a large range of shaft sizes and
handle higher loads. They come standard with
heavy gray cast-iron housings, and provide
more flexibility in sealing options and lubrication
(grease or oil can be used).
These assemblies are predominately designed
for radial loads that are carried directly through
the base. Some of their applications include:
Strip processing equipment steel mills
Conveyors that must accommodate larger
shaft sizes or special seals
Fans and blowers
Felt rolls and drying cylinders within the
paper industry
Crushers, hammer mills, and kilns in the
processing industry
330
The standard split pillow block is made from

cast-iron, while cast-steel or ductile iron are
available as options. The housing is horizontally
split and the cap and base are a mated set; they
cannot be interchanged with other caps or
bases. For accurate realignment, each cap is
mated to the base with dowel pins. Split pillow
blocks are available in two-and four-bolt base
mounting configurations, which allows for
moderate adjustments during installation.
Sealing options for split pillow blocks include the
LER/LOR triple ring seal, the contact seal,
taconite seal, and the end plug.
SKF split pillow blocks come in three styles,
SAF, SAW and SDAF. A fourth type, known as
the extended range, is custom designed for
demanding applications, where requirements
include shaft sizes of 10 to 20 inches.
SAF, the most popular split pillow block, is
manufactured in cast-iron, cast-steel, or ductile
iron. It features a combination of five bearing
types, four sealing options and two mounting
methods, enabling the SAF to be optimized for a
wide variety of applications.
The SAW accommodates the higher capacity

series 23200 bearings, or provides greater
thermal expansion of the shaft when the 22200
bearing is used. It is dimensionally
interchangeable with SAF. Although the bolt
hole spacings and center heights are the same,
the pillow block is about one-inch wider.
The SDAF style is used for applications that
involve heavy or shock loads. SDAF is used
extensively in steel mills, mineral processing,
and other environments using heavy duty
equipment.
SKF split pillow blocks offer optional
customized features, such as special bearings
to meet unusual clearance and/or tolerance
requirements; machined base ends that provide
flat surface for jacking screws; holes for
attachment of various condition monitoring
devices (thermocouples and vibration detection
equipment); and special seals for use with
circulating oil lubrication and high-speed
operation.
Introduction
Correct names for pillow block parts
Grease fitting(s)
bearing lubrication
Bearing
Cap bolts
(typically two or four)
Dowel pins
(for correct mounting of cap)
Mounting bolt holes

(typically two or four)
or blank base when
required
Seal
several types:
depending on service
requirements
Grease fitting(s) for taconite seal

1. Seal lubrication
2. Purging of contaminates
Circulating oil / grease

entry at this point
for spherical roller bearings
Pillow block cap
Stabilizing ring(s)
for held bearing
Circulating oil / grease entry point for

CARB or self-aligning ball bearings
Locknut &
Lockwasher
Adapter sleeve
(comes as an assembly
with locknut and
lockwasher)
Triple ring seal
Base to center height
If circulating oil
drain at these points
Pillow block base
331

Introduction
Cylindrical mounting
Cylindrical mounting involves mounting a
straight bore bearing to a cylindrical shaft
using an interference fit. This mounting method
is preferred if precise location on the shaft is
required. It is also better suited for high speed
applications. In cylindrical mounting, the shaft
must have precision tolerances at the bearing
seat and machined threads for the locknut.
Heating of the inner ring is usually necessary
for mounting.
Adapter mounting
Cylindrical mounting
In adapter mounting a tapered bore bearing is

mounted to a cylindrical shaft through the use of
a tapered adapter sleeve. Adapter mounting is
considered the general purpose mounting
method and most applications of split pillow
blocks use this method of attaching the bearing
to the shaft. The shaft seatings do not need to
be machined to the precision tolerances
necessary for cylindrical mounting and the
mounting method does not require heating the
bearing. Additionally, dismounting is considerably
easier with a tapered adapter sleeve. For these
reasons the total costs associated with adapter
mounting are less than for cylindrical mounting.
Adapter mounting
Multiple bearing types and series accommodate a variety of applications
22317CCK/W33
22217CCK/W33
1317K
1217K
C2317K
C2217K
215/16"
n = 3000 rpm
C = 55100 lbs
332
n = 1900 rpm
C = 108000 lbs
n = 4000 rpm
C = 11000 lbs
n = 3400 rpm
C = 21900 lbs
n = 3000 rpm
C = 53700 lbs
n = 2000 rpm
C = 105000 lbs
Standard split pillow block assortment
SAF
SAFS
SDAF
The cast-iron SAF split pillow blocks

accommodate self-aligning ball bearings or
spherical and toroidal (CARB) roller bearings
and are suitable for adapter or cylindrical
mounting to a shaft. SAF housings are available
for shaft sizes ranging from 13/16" to 101/2" and
offer a choice of two-or four-bolt base
mounting. Their design accommodates grease or
oil lubrication. LER/LOR triple ring seals are
supplied as standard but SAF housings also
accommodate a variety of optional seals such as
contact seals, taconite seals, and end plugs. The
standard housing material is cast-iron.
Dimensional tables begin on page 358.
The SAFS split pillow blocks are cast-steel

versions of the SAF block described to the left.
The cast steel material offers greater strength
and shock resistance for extra heavy-duty
applications. SAFS blocks are used with
cylindrical or adapter mounted spherical roller
bearings. Shaft sizes range from 27/16" to 101/2".
They can be supplied in two-or four-bolt base
mounting arrangements. The SAFS pillow blocks
can be grease or oil lubricated and come
standard with LER/LOR triple ring seals.
Contact seals, taconite seals, and end plugs are
also available. SAFS housings have the same
basic mounting dimensions as SAF housings but
differ in some basic dimensions. SAF
dimensional tables begin on page 358.
The SDAF block is designed for applications

where heavy thrust loads and shock require a
housing of exceptionally sturdy construction.
The four-bolt cap and four-bolt base of the
heavy-duty SDAF are of unusually rugged
proportions adequate to resist shock and heavy
loading in any direction. The caps of these large
housings are supplied with tapped holes for
lifting eyes. SDAF housings accommodate
several series of spherical roller bearings,
cylindrical or adapter mounted. Shaft sizes
range from 315/16" to 99/16". Triple ring seals are
standard; but optional taconite seals and end
plugs are available. SDAF housings can be
grease or oil lubricated. Dimensional tables
begin on page 384.
333

Special application solutions
TY-RPA
TFT
SAW
TY-RPA take-up assemblies consist of a specially

designed, cast-iron, TY-R take-up unit mounted
in an all steel PA take-up housing. These
assemblies are used primarily for belt tensioning
in conveyor applications. The TY-R housing uses
an adapter mounted spherical roller bearing.
Travel is adjusted by turning the protected
adjustment screw from either end of the frame.
TY-RPA assemblies are available in travel
lengths ranging from 12" to 36" and
accommodate shaft sizes from 17/16" to 515/16".
These units are intended for grease lubrication
only and are supplied as standard with one end
closed. Piston ring type seals are used at the
open ends. Versions with both ends open are
also available; the appropriate part numbers
are indicated in the dimensional tables that
begin on page 394. Product nomenclature is
on page 392.
TFT top mount take-up frames are designed

for use with SAF split pillow blocks. As with the
TY-RPA assemblies, TFT assemblies are used
primarily for belt tensioning in conveyor
applications. A SAF block mounts directly to the
top of the TFT frame to complete the assembly.
TFT frames are available in travel lengths from
12" to 48" and accommodate SAF blocks in
shaft sizes from 17/16" to 415/16". Dimensional
tables begin on page 398. Product nomenclature
is on page 393.
SAW split pillow blocks are designed to

accommodate the higher capacity 23200 series
spherical roller bearings. They can also be used
with 22200 series bearings to allow for greater
axial travel or thermal shaft expansion. SAW
blocks have the same basic mounting
dimensions as their SAF counterparts but are
about one-inch wider to accommodate the
wider bearing. Shaft sizes range from 37/16" to
715/16" in adapter mounting. SAW blocks are
available in four-bolt base only and are suitable
for grease or oil lubrication. LER/LOR triple ring
seals are standard but, as with the SAF, other
sealing options are available. Product
nomenclature is on page 403 and dimensional
tables begin on page 404.
Extended range
The extended range split pillow blocks provide
an extremely rugged housing style of
exceptionally sturdy construction for shaft sizes
ranging from 9" to 20" and higher. These blocks
are made-to-order and can be supplied with a
variety of customized features to suit the largest
and most demanding applications. Customized
features can include special seals and grease
shrouds, special bearings and tolerances, specific
bolt hole patterns and machinings for
attachment of auxiliary equipment such as
temperature and vibration detectors. The blocks
can accommodate several series of high capacity
spherical roller bearings in either cylindrical or
adapter mounted arrangements. As with other
SKF split pillow block housings, the extended
range is suitable for grease or oil lubrication and
has a variety of sealing options.
Product nomenclature is on page 408 and
dimensional tables begin on page 412.
334
Seals & speed limits
Standard seals for split pillow blocks
PosiTrac seal
PosiTracTM LOR seal

Standard seal above 2 4"
(see seal table for specific sizes)
O-ring on bore to promote spinning with
the shaft and prevents contaminate
migration between seal and shaft
Close running tolerance to housing surface
Provides grease or oil retention
Aluminum material for spark resistance
Easily upgradable to PosiTracTM Plus
1
PosiTrac Plus seal
Standard LER seal
PosiTrac PlusTM seal
Triple ring LER seal
Standard contact seal offering above 214"

Combination of PosiTrac with nitrile rubber
contact element
Contact element protected by ring and housing providing the maximum protection to the
critical sealing element
Mounts flush in the housing to maintain the
overall housing width
Positive contact even under misalignment
Easy to install
Can be used for purge and non-purge
systems
For use in dirty, dusty and wet
environments
Standard seal on split pillow blocks

below 214"
One-piece rotating labyrinth seal
Close running tolerance between shaft and
housing surfaces
Provides protection from contaminants
Provides grease or oil retention
Aluminum material for spark resistance
Contact seal
One-piece nitrile rubber seal
Positive contact even under misaligned
conditions
Specially molded to fit into the center of the
housing labyrinth
For use in dirty, dusty and wet environments
Available for shaft below 214"
End plug
Contact seal
End plug
Extruded nitrile rubber strip fabricated over

metal plate
Designed to give positive fit in center housing
labyrinth
Provides a perfect closure
335

Standard seals for split pillow blocks
V-ring
Contact
seal
Taconite TER V-ring seal
Taconite TER seal
Taconite TER seal
Taconite-TER V-ring seal
Auxiliary seal features three seals in one

1) Outboard shaft-riding split-contact seal
2) Grease cavity with fitting to flush
contaminants
3) Felt inboard seal
Designed to operate in dusty, dirty,
abrasive and wet environments
Ideal for use in mines, quarries, foundries
and other tough applications
Provides for effective lubricant retention for
more efficient bearing operation
Grease purges through the outboard seal
during regreasing of the Taconite seal, to
expel contaminants
Same features as Taconite TER seal and

also includes:
1) Outboard V ring face riding seal for
minimum shaft wear
2) Grease cavity with fitting to flush
contaminants
3) Felt inboard seal
Designed to operate in dusty, dirty,
abrasive and wet conditions
Ideal for use in mines, quarries, foundries
and other tough applications
Provides for effective lubricant retention for
more efficient bearing operation
Grease purges through the outboard seal
during regreasing of the Taconite seal to
expel contaminants
Accommodates rougher shaft surfaces
336
PosiTrac seals for split pillow blocks

PosiTrac from SKF is the next generation of the
popular SKF LER seal. The lightweight seal is
supplied with new SKF SAF-design split pillow
blocks. It can also be used as a replacement seal
for existing SKF LER and A9508 ring seals.
Two-way sealing protection

PosiTracs inboard O-ring sets it apart from conventional pillow block seals. The O-ring, made of
nitrile rubber, provides two-way sealing protection: it blocks contaminants from migrating
along the shaft into the housing, while preventing lubricant leakage in the opposite direction.
During operation, PosiTracs O-ring makes
complete contact with the spinning shaft. This
allows the entire seal to rotate at shaft speed
and enhances overall sealing effectiveness. The
result is a "Posi"tive "Trac"tive effect.
Quick and easy seal retrofits

Replacing existing SKF LER or A9508 seals with
the new PosiTrac seal is a simple maintenance
task. Because PosiTrac is identical in width to
the LER seals it replaces, it retrofits into existing
SKF pillow blocks without special housing,
sealing or machining requirements.
Once the bearing and housing have been
disassembled, actual seal installation can be
completed quickly. Simply remove the old seal
by hand and slide PosiTrac into position. No
special tools are required.
Although youll experience slight resistance
when installing PosiTrac seals, this requires only
slight hand pressure to overcome. You can also
lubricate the O-ring to ease assembly.
Excellent misalignment and temperature

capabilities
A misalignment capability equivalent to that
of existing SKF LER seal
A broad temperature operating range from
-30 to 230 F
Seal speed ratings equal to bearing speed
ratings
PosiTrac Plus seal from SKF for harshenvironment service

Mining, construction, conveyors and related
harsh-environment applications challenge bearing reliability with constant exposure to dirt,
sand and other contaminants. Especially
demanding environments call for a special
sealPosiTrac Plus.
PosiTrac Plus combines the advanced features
of the PosiTrac seal from SKF with an additional
sealing componenta nitrile rubber contact element that rides on the outer diameter of the
seals aluminum ring. The ring seal provides a
wearing surface, and virtually eliminates any
possibility of shaft wear. This contact seal is
completely encased within the housing and ring
seal labyrinth, protecting it from large particles
of contamination. Together, this system provides
superior sealing in harsh environments.
PosiTrac Plus replaces the SKF B9784 contact
seal. The two major PosiTrac Plus components
are packaged separately for easier inventory
control.
Flush-mounted, easy-to-install design

Some heavy-duty seals for split pillow blocks
have a contact element that extends from the
housing side face, requiring additional axial
spacebut not PosiTrac Plus.
PosiTrac Plus mounts flush with the housing and

has no protruding parts that might snag on belts
or other machinery.
PosiTrac Plus is easy to install. Theres no need
to carefully align the seal with the housing to
ensure proper sealing. PosiTrac Plus drops
straight into an ideal sealing position every time.
Adaptable for purge and non-purge

operations
Grease purging is essential in some applications
(high-contamination mining operations, for
example), but unacceptable in others (papermaking, meat and fruit processing). PosiTrac adapts
easily to either requirement. Simply reverse the
seal orientation in the housing to convert
PosiTrac Plus from purgeable to non-purgeable
operation.
Packaged for convenient upgrades

Users of PosiTrac seals can upgrade to PosiTrac
Plus at any time. To upgrade, order the PosiTrac
Plus contact element that corresponds with the
PosiTrac seal currently in use. The contact element slips easily over the aluminum rings outer
diameter, converting a PosiTrac seal into a
PosiTrac Plus for maximum sealing protection.
How to order PosiTrac Plus from SKF

The two PosiTrac Plus componentsrubber
contact element and aluminum ring with inboard
O-ringare packaged separately and have
different designations. The contact element
designation is B-10724-###; the designation
for the aluminum ring is LOR-XXX. See the
accompanying tables for size ranges.
Easy installation for both purgeable and non-purgeable systems
Inside housing wall

(bearing side)
Grease purgeable set-up

Use purgeable for maximum
contamination exclusion
Inside housing wall

(bearing side)
Non-grease purgeable set-up

Use non-purgeable for maximum
grease retention
337

Seal selection for SAF and SAFS housings
Labyrinth
PosiTracTM
PosiTracTM Plus
Contact
SKF Taconite
Basic part number
LER
LOR PosiTracTM
LOR & B-10724
B-9784
TER
Housing range
SAF 308-311
SAF 507-513
SAF 609-611
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF 308-311
SAF 509-513
SAF 609-611
SAF
SAF
SAF
SAF
SAF
Shaft diameters
11/8" - 25/8"
21/8" - 101/2"
21/8" - 101/2"
11/8" - 25/8"
11/8" - 101/2"
11/8" - 101/2"
11/8" - 101/2"
Material composition
aluminum
aluminum and
nitrile rubber
aluminum and
nitrile rubber
nitrile rubber
steel, felt and

nitrile rubber
steel, felt and

nitrile rubber
steel and
nitrile rubber
Temperature1
300 F max
220 F max
220 F max
220 F max
220 F max
220 F max
220 F max
same as bearing
same as bearing
limited
limited
limited
limited
some
some
limited
limited
extremely
limited
extremely
limited
Grease purgeable
yes
yes
yes
yes
yes
yes
Oil leak prevention
minimal
some
yes
yes
yes
(most of any listed)
yes
yes
Friction
none present
none present
some
some
large amount
large amount
Dusty / dirty
some
some
yes
yes
yes, extreme
conditions
yes, extreme
conditions
yes
Wet / moisture
no
no
yes
yes
yes
yes
yes
High pressure wash
no
no
non direct
non direct
yes
yes
yes
Chemical
some
some
limited
limited
limited
limited
limited
Availability
common sizes
stocked
common sizes
stocked
common sizes
stocked
common sizes
stocked
common sizes
stocked
made to order
common sizes
stocked
6 8 weeks
6 8 weeks
6 8 weeks
6 8 weeks
6 8 weeks
6 8 weeks
6 8 weeks
Speed
Misalignment
Lead time for

made to order
024-056 KA
213-244
312-340
515-544
613-640
024-056 KA
213-244
312-340
515-544
613-640
024-056 KA
213-244
308-340
507-544
609-640
End plug
TER V
EPR
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
SAF
024-056 KA
213-244
308-340
507-544
609-640
1 A special lubrication may be required to accommodate 400 F. Consult SKF or your lubrication supplier.
2 Consult SKF Applications Engineering for specific speed ratings.
3 A self aligning bearing in a split housing assembly will not realize the full bearing misalignment capability; misalignment is limited by seal type.
338
024-056 KA
213-244
308-340
507-544
609-640
Seal chart for SKF SAF, SAFS and SAW split pillow block housings
S-1
S-1
Shaft
000
500
diameter Series Series
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
O-Ring
designation
for LOR2
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
"V"-Ring
seal
type
Speed
limit
rpm4
LER-13
LER-14
LER-15
LER-16
---------
---------
---------
TER-13
TER-14
TER-15
TER-16
TER-13 V
TER-14 V
TER-15 V
TER-16 V
2250
2250
2250
2175
EPR-2
EPR-2
EPR-2
EPR-3
LER-17
LER-18
LER-19
LER-20
---------
B-9784-12
----B-9784-15
3800
----3400
TER-17
TER-18
TER-19
TER-20
TER-17 V
TER-18 V
TER-19 V
TER-20 V
2175
2175
1800
1800
EPR-3
EPR-3
EPR-4
EPR-4
308*
LER-21
LER-22
LER-23
LER-24
---------
------B-9784-19
------2950
TER-21
TER-22
TER-23
TER-24
TER-21 V
TER-22 V
TER-23 V
TER-24 V
1800
1575
1575
1575
EPR-4
EPR-5
EPR-5
EPR-5
309*
LER-25
LER-26
LER-27
LER-28
---------
--B-9784-21
-----
--2950
-----
TER-25
TER-26
TER-27
TER-28
TER-25 V
TER-26 V
TER-27 V
TER-28 V
1575
1450
1450
1450
EPR-5
EPR-6
EPR-6
EPR-6
LOR-31
LER-29
LOR-32
LER-30
AS-568-034
--AS-568-035
---
B-10724-32
B-9784-24
B-10724-32
---
2600
2600
2600
---
TER-31
TER-29
TER-32
TER-30
TER-31 V
TER-29 V
TER-32 V
TER-30 V
1400
1400
1400
1400
EPR-7
EPR-6
EPR-7
EPR-6
LOR-33
LER-34
LER-35
LOR-36
AS-568-035
----AS-568-036
B-10724-32
----B-10724-37
2600
----2350
TER-33
TER-34
TER-35
TER-36
TER-33 V
TER-34 V
TER-35 V
TER-36 V
1075
1300
1300
1250
EPR-7
----EPR-7
LOR-37
LER-39
LOR-38
LER-40
AS-568-037
--AS-568-037
---
B-10724-37
B-9784-37
B-10724-37
B-9784-35
2350
--2350
---
TER-37
TER-39
TER-38
TER-40
TER-37 V
TER-39 V
TER-38 V
TER-40 V
1250
1250
1250
1200
EPR-7
--EPR-7
---
LOR-42
LER-41
LOR-43
LOR-44
AS-568-038
--AS-568-038
AS-568-039
B-10724-44
--B-10724-44
B-10724-44
2150
--2150
2150
TER-42
TER-41
TER-43
TER-44
TER-42 V
TER-41 V
TER-43 V
TER-44 V
1150
1150
1150
1150
EPR-8
--EPR-8
EPR-8
LOR-45
LOR-182
LOR-46
LOR-51
AS-568-039
AS-568-149
AS-568-040
AS-568-040
B-10724-44
B-10724-184
B-10724-44
B-10724-53
2150
1950
2150
1950
TER-45
TER-182
TER-46
TER-51
TER-45 V
TER-182 V
TER-46 V
TER-51 V
1150
1050
900
1050
EPR-8
EPR-10
EPR-8
EPR-9
LOR-57
LOR-183
LOR-47
LOR-52
AS-568-150
AS-568-150
AS-568-040
AS-568-040
B-10724-184
B-10724-184
B-10724-44
B-10724-53
1900
1950
2150
1950
TER-57
TER-183
TER-47
TER-52
TER-57 V
TER-183 V
TER-47 V
TER-52 V
850
1050
1075
1050
EPR-10
EPR-10
EPR-8
EPR-9
1-1/8"
1-3/16"
1-1/4"
1-3/8"
507
507*
507
509
609
1-7/16"
1-1/2"
1-5/8"
1-11/16"
509*
509
510
510*
609*
609
610
610*
1-3/4"
1-13/16"
1-7/8"
1-15/16"
510
511
511
511*
610
611
611
611*
2"
2"
2-1/16"
2-1/8"
511
513
513
513
611
2-1/8"
2-3/16"
2-3/16"
2-1/4"
2-1/4"
2-5/16"
2-3/8"
2-3/8"
2-7/16"
2-1/2"
2-1/2"
2-9/16"
308*
309*
310*
311*
613
312
613*
312
513*
513
613
312*
210
210
310
310*
515
615
213
313
515*
615*
213*
313*
515
615
213
313
311*
2-9/16"
2-5/8"
2-5/8"
2-11/16"
516
516
516*
616
616*
314*
314
2-3/4"
2-13/16"
2-13/16"
2-13/16"
516
616
617
314
2-3/16"
2-7/8"
2-7/8"
2-7/8"
616
314
311
517
213
312
313
215*
216
315*
316
617
517
213
312*
313
215
216
315
Taconite seals5
End plugs
* = Standard shaft diameter, all others are optional shaft diameters

1 = Speed rating same as bearing speed rating; see bearing tables
2 = O-ring supplied with LOR is for replacement only, AS-568-### are industry standard O-rings available at most SKF authorized distributors
3 = B-10724-###'s are the SKF PosiTrac Plus seal and require the LOR
4 = For stepped shaft housing designs the largest shaft diameter is the limiting speed limit
5 = Most taconite seals are made to order; contact SKF for availability, all "V"-ring versions are made to order
339

S-1
S-1
Shaft
000
500
2-7/8"
2-15/16"
2-15/16" 517*
2-15/16"
3"
3"
3"
3-1/16"
3-1/16"
3-1/16"
3-1/8"
3-1/8"
3-1/8"
3-3/16"
3-3/16"
3-1/4"
3-1/4"
3-5/16"
3-5/16"
3-5/16"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-7/16"
3-7/16"
3-1/2"
3-1/2"
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
"V"-Ring
seal
type
Speed
limit
rpm4
B-10724-184
B-10724-184
B-10724-53
B-10724-184
1900
1950
1950
1900
TER-58
TER-184
TER-53
TER-59
TER-58 V
TER-184 V
TER-53 V
TER-59 V
850
1050
1050
850
EPR-10
EPR-10
EPR-9
EPR-10
316
LOR-58
AS-568-150
LOR-184
AS-568-151
LOR-53 AS-568-141
316
LOR-59
AS-568-151
617*
213
617
517
518
518
313
216
213
313
313*
216
217
213
313
216
314
217
618
618*
518
618
520
620
AS-568-151
AS-568-041
AS-568-151
38309-186
B-10724-184
B-10724-53
B-10724-184
B-10724-188
1950
1950
1900
1800
TER-185
TER-54
TER-60
TER-186
TER-185 V
TER-54 V
TER-60 V
TER-186 V
1050
850
850
950
EPR-10
EPR-9
EPR-10
EPR-11
LOR-55
LOR-61
LOR-187
LOR-56
38309-55
38309-61
AS-568-152
AS-568-042
B-10724-53
B-10724-64
B-10724-188
B-10724-53
1950
1450
1800
1950
TER-55
TER-61
TER-187
TER-56
TER-55 V
TER-61 V
TER-187 V
TER-56 V
1000
775
950
1000
EPR-9
EPR-9
EPR-11
EPR-9
317
LOR-62
LOR-188
LOR-63
LOR-189
AS-568-042
AS-568-152
AS-568-042
AS-568-152
B-10724-64
B-10724-188
B-10724-64
B-10724-188
1450
1800
1450
1800
TER-62
TER-188
TER-63
TER-189
TER-62 V
TER-188 V
TER-63 V
TER-189 V
775
950
775
950
EPR-9
EPR-11
EPR-9
EPR-11
318
LOR-64
LOR-100
LOR-65
LOR-190
AS-568-042
38309-100
38309-65
38309-190
B-10724-64
B-10724-102
B-10724-64
B-10724-188
1450
1650
1450
1800
TER-64
TER-100
TER-65
TER-190
TER-64 V
TER-100 V
TER-65 V
TER-190 V
925
900
775
750
EPR-9
EPR-12
EPR-9
EPR-11
318*
LOR-78
LOR-66
LOR-101
LOR-191
AS-568-043
AS-568-043
AS-568-153
AS-568-153
B-10724-79
B-10724-64
B-10724-102
B-10724-188
1650
1450
1650
1800
TER-78
TER-66
TER-101
TER-191
TER-78 V
TER-66 V
TER-101 V
TER-191 V
900
775
900
750
--EPR-9
EPR-12
EPR-11
LOR-79
LOR-102
LOR-80
LOR-103
AS-568-043
AS-568-153
AS-568-043
AS-568-153
B-10724-79
B-10724-102
B-10724-79
B-10724-102
1450
1650
1450
1650
TER-79
TER-102
TER-80
TER-103
TER-79 V
TER-102 V
TER-80 V
TER-103 V
900
900
900
900
--EPR-12
--EPR-12
LOR-81
LOR-83
LOR-82
LOR-84
38309-81
38309-83
AS-568-044
AS-568-154
B-10724-79
B-10724-106
B-10724-79
B-10724-106
1450
1275
1450
1275
TER-81
TER-83
TER-82
TER-84
TER-81 V
TER-83 V
TER-82 V
TER-84 V
900
850
850
850
--EPR-12
--EPR-12
LOR-85
LOR-86
LOR-105
AS-568-154
AS-568-154
AS-568-154
AS-568-154
B-10724-106
B-10724-106
B-10724-106
B-10724-106
1275
1275
1275
1275
TER-85
TER-104
TER-86
TER-105
TER-85 V
TER-104 V
TER-86 V
TER-105 V
850
675
850
675
EPR-12
EPR-12
EPR-12
EPR-12
LOR-87
LOR-106
LOR-107
LOR-108
38309-87
38309-106
38309-107
AS-568-155
B-10724-106
B-10724-106
B-10724-109
B-10724-109
1275
1275
1450
1450
TER-87
TER-106
TER-107
TER-108
TER-87 V
TER-106 V
TER-107 V
TER-108 V
850
675
775
775
EPR-12
EPR-12
EPR-13
EPR-13
317
213*
317
317*
314
314*
217*
217
220
217
218
215/216 315
520
217
220
218*
620
215*/216315*
520*
620*
520
620
220
215/216 315
3-9/16"
3-9/16"
3-5/8"
3-5/8"
220
215/216 315
316
215/216*315
316*
3-11/16"
3-11/16"
3-3/4"
3-3/4"
316
3-13/16"
3-13/16"
3-13/16" 522
3-7/8"
316
220*
320
LOR-104
316
320
622
522
317
622
317
320*

4 = For stepped shaft housing designs, the largest shaft diameter is the limiting speed limit
340
End plugs
LOR-185
LOR-54
LOR-60
LOR-186
216*
316*
618
518*
O-Ring
designation
for LOR2
Taconite seals5
S-1
S-1
Shaft
000
500
3-7/8"
3-15/16"
3-15/16"
4"
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
O-Ring
designation
for LOR2
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
LOR-88
LOR-109
LOR-89
LOR-110
AS-568-045
AS-568-155
AS-568-045
AS-568-155
B-10724-89
B-10724-109
B-10724-89
B-10724-109
1450
1450
1450
1450
TER-88
TER-88 V
TER-109 TER-109 V
TER-89
TER-89 V
TER-110 TER-110 V
775
775
775
775
--EPR-13
--EPR-13
217
522*
622*
522
622
317*
217*
317
Taconite seals5
"V"-Ring
seal
type
End plugs
Speed
limit
rpm4
4"
4-1/16"
4-1/8"
4-3/16"
024
024
024*
524
524
524*
624
624
624*
217
218
218*
218
318
318*
318
222
222
222*
322
322
322*
LOR-90
LOR-111
LOR-112
LOR-113
AS-568-045
38309-111
AS-568-156
AS-568-156
B-10724-89
B-10724-113
B-10724-113
B-10724-113
1450
1350
1350
1350
TER-90
TER-90 V
TER-111 TER-111 V
TER-112 TER-112 V
TER-113 TER-113 V
775
750
750
725
--EPR-14
EPR-14
EPR-14
4-1/4"
4-5/16"
4-3/8"
4-7/16"
024
026
026
026*
524
526
526
526*
624
626
626
626*
218
220
220
220
318
320
320
320
222
224
224
224
322
324
324
324
LOR-114
LOR-115
LOR-116
LOR-117
AS-568-156
38309-115
AS-568-157
AS-568-157
B-10724-113
B-10724-117
B-10724-117
B-10724-117
1350
1300
1300
1300
TER-114 TER-114 V
TER-115 TER-115 V
TER-116 TER-116 V
TER-117 TER-117 V
725
700
700
700
EPR-14
EPR-15
EPR-15
EPR-15
4-1/2"
026
4-9/16"
4-13/16" 028
4-7/8"
028
526
626
528
528
628
628
220*
220
222
222*
320*
320
322
322*
224
224*
226
226
324
324*
326
326
LOR-118
LOR-119
LOR-120
LOR-121
AS-568-157
38309-119
38309-120
AS-568-159
B-10724-117
B-10724-117
B-10724-122
B-10724-122
1300
1300
1150
1150
TER-118 TER-118 V
TER-119 TER-119 V
TER-120 TER-120 V
TER-121 TER-121 V
675
675
625
625
EPR-15
EPR-15
EPR-27
EPR-27
4-15/16"
5-1/8"
5-3/16"
5-1/4"
028*
030
030*
030
528*
530
530*
530
628*
630
630*
630
222
224
224
224
322
324
324
324
226*
228
228
228
326*
328
328
328
LOR-122
LOR-124
LOR-125
LOR-126
AS-568-159
AS-568-160
AS-568-160
AS-568-160
B-10724-122
B-10724-125
B-10724-125
B-10724-125
1150
1075
1075
1075
TER-122
TER-124
TER-125
TER-126
TER-122 V
TER-124 V
TER-125 V
TER-126 V
625
590
590
575
EPR-27
EPR-16
EPR-16
EPR-16
5-5/16"
5-3/8"
5-3/8"
5-7/16"
030
30
032
032*
224*
224
324*
324
228*
228
328*
328
LOR-127
LOR-128
LOR-129
LOR-130
38309-127
AS-568-161
AS-568-253
AS-568-254
B-10724-125
B-10724-125
B-10724-130
B-10724-130
1075
1075
1050
1050
TER-127 TER-127 V
TER-128 TER-128 V
TER-129 TER-129 V
TER-130 TER-130 V
575
575
560
560
EPR-16
EPR-16
EPR-16
EPR-16
226
226
226
326
326
326
230
230
230*
330
330
330*
LOR-131
LOR-132
LOR-133
LOR-134
AS-568-254
AS-568-162
AS-568-162
AS-568-162
B-10724-130
B-10724-134
B-10724-134
B-10724-134
1050
850
850
850
TER-131 TER-131 V
TER-132 TER-132 V
TER-133 TER-133 V
TER-134 TER-134 V
560
460
460
460
EPR-16
EPR-17
EPR-17
EPR-17
226
326
226*
326*
232
230
232
230
332
330
332
330
LOR-138
LOR-135
LOR-139
LOR-136
AS-568-257
38309-135
AS-568-257
AS-568-163
B-10724-140
B-10724-134
B-10724-140
B-10724-134
950
850
950
850
TER-138 TER-138 V
TER-135 TER-135 V
TER-139 TER-139 V
TER-136 TER-136 V
520
520
520
520
EPR-18
EPR-17
EPR-18
EPR-17
226
326
232
230
232
232*
332
330
332
332*
LOR-140
LOR-137
LOR-141
LOR-142
AS-568-258
AS-568-163
AS-568-258
38309-142
B-10724-140
B-10724-134
B-10724-140
B-10724-140
950
850
950
950
TER-140 TER-140 V
TER-137 TER-137 V
TER-141 TER-141 V
TER-142 TER-142 V
520
520
500
500
EPR-18
EPR-17
EPR-18
EPR-18
228
228*
228
328
328*
328
334
LOR-143
LOR-144
LOR-145
LOR-146
AS-568-164
AS-568-164
38309-145
38309-146
B-10724-144
B-10724-144
B-10724-144
B-10724-148
925
925
925
875
TER-143
TER-144
TER-145
TER-146
490
490
490
460
------EPR-19
532
532*
632
632*
5-1/2"
032
5-5/8"
5-11/16"
5-3/4"
532
632
5-13/16" 034
5-13/16"
5-7/8"
034
5-7/8"
534
5-15/16" 034*
5-15/16"
6"
034
6-1/16"
6-3/16"
6-1/4"
6-5/16"
6-5/16"
036
534
534*
534
536
634
634
634*
634
234
TER-143 V
TER-144 V
TER-145 V
TER-146 V

341

S-1
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
Shaft
000
diameter Series
500
Series
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
O-Ring
designation
for LOR2
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
"V"-Ring
seal
type
Speed
limit
rpm4
6-3/8"
6-7/16"
6-1/2"
6-9/16"
536
536*
536
234
234
234
334
334*
334
AS-568-260
AS-568-260
AS-568-260
38309-150
B-10724-148
B-10724-148
B-10724-148
B-10724-151
875
875
875
850
TER-147
TER-148
TER-149
TER-150
TER-147 V
TER-148 V
TER-149 V
TER-150 V
460
460
460
460
EPR-19
EPR-19
EPR-19
---
S-1
036
036*
036
6-5/8"
6-11/16"
6-13/16" 038
6-7/8"
038
6-15/16" 038*
7"
038
7-1/16"
7-1/8"
040
7-3/16"
7-1/4"
7-7/16"
7-1/2"
040*
040
7-9/16"
7-5/8"
7-13/16" 044
7-7/8"
044
7-15/16" 044*
8"
044
8-1/4"
8-5/16"
538
538
638
638
538*
538
638*
638
540
640
540*
540
640*
640
544
544
230
330
230*
230
232
232
330*
330
332
332
236
236*
LOR-151
LOR-152
LOR-153
LOR-154
AS-568-166
AS-568-166
38309-153
AS-568-262
B-10724-151
B-10724-151
B-10724-155
B-10724-155
850
850
825
825
TER-151
TER-152
TER-153
TER-154
TER-151 V
TER-152 V
TER-153 V
TER-154 V
460
460
440
440
----EPR-20
EPR-20
232
232*
232
332
332*
332
236
236
236
238
338
LOR-155
LOR-156
LOR-157
LOR-158
AS-568-262
AS-568-262
38309-157
AS-568-263
B-10724-155
B-10724-155
B-10724-155
B-10724-159
825
825
825
800
TER-155
TER-156
TER-157
TER-158
TER-155 V
TER-156 V
TER-157 V
TER-158 V
440
440
440
425
EPR-20
EPR-20
EPR-20
EPR-21
338
338*
340
340
LOR-159
LOR-160
LOR-161
LOR-162
AS-568-263
AS-568-263
AS-568-264
AS-568-264
B-10724-159
B-10724-159
B-10724-161
B-10724-161
800
800
650
650
TER-159
TER-160
TER-161
TER-162
TER-159 V
TER-160 V
TER-161 V
TER-162 V
425
425
410
410
EPR-21
EPR-21
EPR-22
EPR-22
340
340*
LOR-163
LOR-164
LOR-165
LOR-166
AS-568-265
AS-568-265
AS-568-266
AS-568-266
B-10724-161
B-10724-161
B-10724-167
B-10724-167
650
650
725
725
TER-163
TER-164
TER-165
TER-166
TER-163 V
TER-164 V
TER-165 V
TER-166 V
410
390
390
390
EPR-22
EPR-22
EPR-23
EPR-23
LOR-167
LOR-168
LOR-169
LOR-170
AS-568-266
AS-568-266
AS-568-267
AS-568-268
B-10724-167
B-10724-167
B-10724-170
B-10724-170
725
725
600
600
TER-167
TER-168
TER-169
TER-170
TER-167 V
TER-168 V
TER-169 V
TER-170 V
385
385
365
365
EPR-23
EPR-23
EPR-24
EPR-24
LOR-171
LOR-172
LOR-550
LOR-173
AS-568-268
AS-568-268
AS-568-268
AS-568-268
B-10724-170
B-10724-170
B-10724-552
B-10724-170
600
600
680
600
TER-171
TER-172
TER-550
TER-173
TER-171 V
TER-172 V
TER-550 V
TER-173 V
365
365
360
360
EPR-24
EPR-24
X-5217-4
EPR-24
LOR-551
LOR-174
LOR-175
LOR-176
AS-568-268
AS-568-269
AS-568-269
AS-568-270
B-10724-552
B-10724-175
B-10724-175
B-10724-175
680
650
650
650
TER-551
TER-174
TER-175
TER-176
TER-551 V
TER-174 V
TER-175 V
TER-176 V
360
350
350
350
X-5217-4
EPR-25
EPR-25
EPR-25
LOR-177
LOR-552
LOR-513
LOR-553
AS-568-270
AS-568-270
AS-568-270
AS-568-272
B-10724-175
B-10724-552
B-10724-552
B-10724-178
650
640
640
600
TER-177
TER-552
TER-513
TER-553
TER-177 V
TER-552 V
TER-513 V
TER-553 V
350
340
340
325
EPR-25
X-5217-4
X-5217-4
X-5217-2
LOR-178
LOR-179
LOR-180
LOR-181
AS-568-272
AS-568-273
AS-568-273
AS-568-273
B-10724-178
B-10724-178
B-10724-178
B-10724-178
600
600
600
600
TER-178
TER-179
TER-180
TER-181
TER-178 V
TER-179 V
TER-180 V
TER-181 V
320
315
315
315
X-5217-2
X-5217-2
X-5217-2
X-5217-2
LOR-607
LOR-568
LOR-606
LOR-519
AS-568-274
AS-568-274
AS-568-275
AS-568-275
B-10724-607
B-10724-607
B-10724-606
B-10724-606
575
575
550
550
TER-607
TER-568
TER-606
TER-519
TER-607 V
TER-568 V
TER-606 V
TER-519 V
310
305
295
290
X-5217-2
X-5217-2
X-5217-1
X-5217-1
234*
234
334*
334
238
238*
240
240
234
234
236*
236
334
334
240
240*
338
338
244
244*
238*
238
338*
338
244
244
238
338
244
240
240*
240
340
340*
340
8-7/8"
8-15/16" 048*
9"
048
9-7/16" 052*
240
340
9-1/2"
052
9-9/16"
9-5/8"
9-11/16"
244
244*
244
244
048
8-1/2"
048
8-11/16"
8-3/4"
8-13/16"
9-15/16"
10"
10-7/16"
10-1/2"
056*
056
056*
056

342
End plugs
LOR-147
LOR-148
LOR-149
LOR-150
236
236
238
238
8-3/8"
8-7/16"
8-7/16"
8-1/2"
544*
544
Taconite seals5
Seal chart for SKF SDAF and SDAFS split pillow block housings
Shaft
diameter
S-1
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
500
Series
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
O-Ring
designation
for LOR2
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
"V"-Ring
seal
type
Speed
limit
rpm4
1950
1950
1950
1950
TER-57
TER-58
TER-59
TER-60
TER-57 V
TER-58 V
TER-59 V
TER-60 V
1050
1050
1050
1050
EPR-10
EPR-10
EPR-10
EPR-10
TER-67
TER-68
TER-69
TER-70
TER-67 V
TER-68 V
TER-69 V
TER-70 V
950
950
950
950
EPR-11
EPR-11
EPR-11
EPR-11
TER-72
TER-73
TER-74
TER-75
TER-72 V
TER-73 V
TER-74 V
TER-75 V
750
750
750
900
EPR-11
EPR-11
EPR-11
EPR-11
TER-76
TER-87
TER-91
TER-92
TER-76 V
TER-87 V
TER-91 V
TER-92 V
900
675
775
775
EPR-11
EPR-12
EPR-13
EPR-13
End plugs
2-13/16"
2-7/8"
2-15/16"
3"
617
617*
617
LOR-57
LOR-58
LOR-59
LOR-60
AS-568-150
AS-568-150
AS-568-151
AS-568-151
B-10724-184
B-10724-184
B-10724-184
B-10724-184
3-1/16"
3-1/8"
3-3/16"
3-1/4"
618
618
618*
618
LER-67
LER-68
LER-69
LER-70
---------
---6
---6
---6
---6
LER-72
LER-73
LER-74
LER-75
---------
---6
---6
---6
---6
LER-76
LER-87
LER-91
LER-92
---------
---6
---6
---6
---6
LER-93
LER-94
LER-96
LOR-111
------38309-111
-----6
---6
-----6
B-10724-113 1350
TER-93
TER-94
TER-96
TER-111
TER-93 V
TER-94 V
TER-96 V
TER-111 V
775
775
750
725
EPR-13
EPR-13
--EPR-14
LOR-112
LOR-113
LOR-114
LOR-115
AS-568-156
AS-568-156
AS-568-156
38309-115
B-10724-113
B-10724-113
B-10724-113
B-10724-117
1350
1350
1350
1300
TER-112
TER-113
TER-114
TER-115
TER-112 V
TER-113 V
TER-114 V
TER-115 V
725
725
725
700
EPR-14
EPR-14
EPR-14
EPR-15
LOR-116
LOR-117
LOR-118
LOR-119
AS-568-157
AS-568-157
AS-568-157
38309-119
B-10724-117
B-10724-117
B-10724-117
B-10724-117
1300
1300
1300
1300
TER-116
TER-117
TER-118
TER-119
TER-116 V
TER-117 V
TER-118 V
TER-119 V
700
700
700
700
EPR-15
EPR-15
EPR-15
EPR-15
LER-205
LOR-119
LOR-121
LOR-122
--38309-119
AS-568-159
AS-568-159
---6
B-10724-117
B-10724-122
B-10724-122
--1300
1150
1150
TER-205
TER-119
TER-121
TER-122
TER-205 V
TER-119 V
TER-121 V
TER-122 V
675
575
625
520
--EPR-15
--EPR-27
LOR-124
LOR-125
LOR-126
LOR-127
AS-568-160
AS-568-160
AS-568-160
38309-127
B-10724-125
B-10724-125
B-10724-125
B-10724-125
1075
1075
1075
1075
TER-124
TER-125
TER-126
TER-127
TER-124 V
TER-125 V
TER-126 V
TER-127 V
590
590
590
575
EPR-16
EPR-16
EPR-16
---
LOR-128
LOR-129
LOR-130
LOR-131
AS-568-161
AS-568-253
AS-568-254
AS-568-254
B-10724-125
B-10724-130
B-10724-130
B-10724-130
1075
1050
1050
1050
TER-128
TER-129
TER-130
TER-131
TER-128 V
TER-129 V
TER-130 V
TER-131 V
575
575
560
560
EPR-16
EPR-16
EPR-16
EPR-16
3-3/8"
3-5/16"
3-3/8"
3-7/16"
617
Taconite seals5
317*
318*
520
520
520*
620
620
620*
3-1/2"
3-13/16"
3-13/16"
3-7/8"
520
620
522
522
622
622
3-15/16"
4"
4-1/8"
4-1/16"
522*
522
622*
622
524
624
4-1/8"
4-3/16"
4-1/4"
4-5/16"
524
524*
524
526
624
624*
624
626
4-3/8"
4-7/16"
4-1/2"
4-9/16"
526
526*
526
526
626
626*
626
626
4-1/2"
4-9/16"
4-7/8"
4-15/16"
528
528
528*
5-1/8"
5-3/16"
5-1/4"
5-5/16"
530
530*
530
530
630
630*
630
630
5-3/8"
5-3/8"
5-7/16"
5-1/2"
530
532
532*
532
630
220*
320*
317*
318*
222*
220*
222*
224*
322*
320*
224*
324*
226*
326*
322*
324*
228*
---
---
---
---

6 = Consult SKF Applications Engineering for options
343

Seal chart for SKF SDAF and SDAFS split pillow block housings
Shaft
diameter
S-1
S-1
S-2
S-2
S-3
S-3
Triple ring seal1
Contact seals
500
Series
600
Series
200
Series
300
Series
200
Series
300
Series
Ring seal
part
number
O-Ring
designation
for LOR2
Contact seal
P/N3
Speed
limit
rpm4
Contact
seal
type
"V"-Ring
seal
type
Speed
limit
rpm4
230*
330*
LER-211
LOR-134
LOR-136
LER-215
--AS-568-162
AS-568-163
---
---6
B-10724-130
B-10724-130
---6
--1050
1050
---
TER-211
TER-134
TER-136
TER-215
TER-211 V
TER-134 V
TER-136 V
TER-215 V
560
460
520
515
EPR-17
EPR-17
--EPR-19
LOR-142
LER-217
LOR 144
LOR-146
LOR-147
38309-142
--AS-568-164
38309-146
AS-568-260
B-10724-140
---6
B-10724-144
B-10724-148
B-10724-148
950
--925
875
875
TER-142
TER-217
TER-144
TER-146
TER-147
TER-142 V
TER-217 V
TER-144 V
TER-146 V
TER-147 V
435
435
--475
475
EPR-18
EPR-19
--EPR-19
EPR-19
LOR-148
LOR-149
LER-220
LOR-151
AS-568-260
AS-568-260
--AS-568-166
B-10724-148
B-10724-148
---6
B-10724-151
875
875
--850
TER-148
TER-149
TER-220
TER-151
TER-148 V
TER-149 V
TER-220 V
TER-151 V
475
475
475
460
EPR-19
EPR-19
EPR-26
---
LOR-154
LER-223
LER-224
LOR-156
AS-568-262
----AS-568-262
B-10724-155
B-9784-130
---6
B-10724-155
825
750
--825
TER-154
TER-223
TER-224
TER-156
TER-154 V
TER-223 V
TER-224 V
TER-156 V
390
390
440
435
EPR-20
EPR-21
EPR-21
---
LER-225
LER-228
LER-229
LER-230
---------
---6
B-9784-140
B-9784-141
---6
--800
700
---
TER-225
TER-228
TER-229
TER-230
TER-225 V
TER-228 V
TER-229 V
TER-230 V
435
425
365
410
--EPR-22
EPR-22
---
240*
LER-233
LOR-165
LER-234
LER-236
--AS-568-266
-----
B-9784-146
B-17024-167
B-9784-148
---6
650
725
750
---
TER-233
TER-165
TER-234
TER-236
TER-233 V
TER-165 V
TER-234 V
TER-236 V
350
390
390
385
EPR-23
----EPR-24
244*
LER-239
LER-240
LER-244
LER-248
---------
---6
---6
B-9784-159
---6
----650
---
TER-239
TER-240
TER-244
TER-248
TER-239 V
TER-240 V
TER-244 V
TER-248 V
315
365
350
315
EPR-25
-------
5-7/16"
5-3/4"
5-7/8"
5-15/16"
6-1/16"
6-1/16"
6-1/4"
6-5/16"
6-3/8"
6-7/16"
6-1/2"
6-7/16"
6-5/8"
6-7/8"
6-7/8"
6-15/16"
7"
7"
7-3/16"
7-1/4"
7-7/16"
7-5/8"
7-13/16"
7-13/16"
7-15/16"
8-5/16"
8-3/8"
8-3/4"
9-9/16"
632*
226*
326*
634*
232*
332*
228*
536
536
536*
536
636*
334*
230*
330*
236*
336*
538*
638*
232*
332*
540*
640*
238*
334*
236*
336*
544*
238*
240*
244*
338*
338*
Taconite seals5

6 = Consult SKF Applications Engineering for options
344
End plugs
Seal chart for SKF SDAF extended range adapter mount split pillow block housings5
S-1
Shaft
diameter
SDAF 23000
"8-15/16"
9"
9-7/16"
9-1/2"
9-15/16"
10"
10-7/16"
10-1/2"
10-15/16"
10-15/16"
11"
11"
S-1
Triple ring seal1,4
SDAF 23100
SDAF 23200
Ring seal
part
number
Contact seal
V-Ring seal
Speed
limit
rpm
3152 KA*
3152 KA
3248
3248
3252
3252
KA*
KA
KA*
KA
ERF-914
ERF-828
ERF-891
ERF-842
TER-914
TER-828
TER-891
TER-842
TER-914 V
TER-828 V
TER-891 V
TER-842 V
280
280
275
275
X-5217-25
X-5217-25
X-5217-53
X-5217-53
3256 KA*
3256 KA
ERF-845
ERF-820
ERF-973
ERF-840
TER-845
TER-820
TER-973
TER-840
TER-845 V
TER-820 V
TER-973 V
TER-840 V
270
270
260
260
X-5217-35
X-5217-54
X-5217-52
X-5217-52
3260 KA
ERF-858
ERF-1002
ERF-825
ERF-1003
TER-858
TER-1002
TER-825
TER-1003
TER-858 V
TER-1002 V
TER-825 V
TER-1003 V
280
270
275
270
X-5217-9
X-5217-55
X-5217-9
X-5217-55
3264 KA*
ERF-861
ERF-832
ERF-859
ERF-900
TER-861
TER-832
TER-859
TER-900
TER-861 V
TER-832 V
TER-859 V
TER-900 V
270
265
260
260
X-5217-16
X-5217-16
X-5217-3
X-5217-43
ERF-818
ERF-865
ERF-975
ERF-866
TER-818
TER-865
TER-975
TER-866
TER-818 V
TER-865 V
TER-975 V
TER-866 V
255
250
250
245
X-5217-3
X-5217-29
--X-5217-29
ERF-869
ERF-846
ERF-872
ERF-979
TER-869
TER-846
TER-872
TER-979
TER-869 V
TER-846 V
TER-872 V
TER-979 V
240
235
230
230
X-5217-28
X-5217-28
X-5217-27
---
ERF-823
ERF-875
ERF-977
ERF-876
TER-823
TER-875
TER-977
TER-876
TER-823 V
TER-875 V
TER-977 V
TER-876 V
225
215
215
215
X-5217-27
X-5217-12
--X-5217-12
ERF-882
ERF-976
ERF-847
ERF-969
TER-882
TER-976
TER-847
TER-969
TER-882 V
TER-976 V
TER-847 V
TER-969 V
200
200
200
185
----X-5217-21
X-5217-23
ERF-907
ERF-958
ERF-838
ERF-888
TER-907
TER-958
TER-838
TER-888
TER-907 V
TER-958 V
TER-838 V
TER-888 V
185
180
175
170
X-5217-5
--X-5217-48
---
ERF-978
ERF-926
TER-978
TER-926
TER-978 V
TER-926 V
170
165
-----
S-1
3156
3156
3156
3156
3060 KA*
KA
KA
KA*
KA
3160 KA*
3260 KA*
3060 KA
3160 KA
11-7/16"
11-1/2"
11-15/16"
11-15/16"
3064 KA*
3064 KA
3064 KA*
12"
12-7/16"
12-7/16"
12-1/2"
3064 KA
3068 KA*
12-15/16"
13"
13-7/16"
13-7/16"
3072 KA*
3072 KA
3072 KA*
13-1/2"
13-15/16"
13-15/16"
14
3072 KA
3076 KA*
3172 KA
3176 KA*
3076 KA
3176 KA
3164 KA*
3168 KA*
3268 KA*
3068 KA
3172 KA*
3272 KA*
3276 KA*
14-15/16"
14-15/16"
15"
15-3/4"
3080 KA*
3080 KA*
3084 KA*
15-3/4"
16-1/2"
17"
18"
3088 KA*
3092 KA*
3096 KA*
18-1/2"
19-1/2"
230/500 KA*
230/530 KA*
3180 KA*
3280KA*
3184
3188
3192
3196
3284 KA*
3288 KA*
KA*
KA*
KA*
KA*
Taconite seals2,3
End plugs

1 = Speed rating same as bearing speed rating; see bearing tables; not all optional shaft diameter ring seals are stocked items
2 = Taconite seals are made to order; contact SKF for availability
3 = The SKF preferred taconite seal design is a split bolt-on-taconite auxiliary cover
4 = Optional shaft diameters may require special machining so alternate ring seals or end plugs require review prior to ordering
5 = These housings are available in cast-Iron (SDAF), cast-steel (SDAFS) and ductile-iron (SDAFD)
345

Lubrication
Introduction
The information presented in this section is
intended to provide the user with basic and
practical information on the lubrication of split
pillow blocks. It does not include a theoretical
background. As the world leader in rolling
bearing technology, SKF has extensive
information available on the subject of bearing
lubrication theory. Some of this information can
be found in other SKF publications including the
General Catalog (6000 EN) and the Bearing
Installation and Maintenance Guide (140-710).
If you have questions regarding bearing
lubrication not addressed here or in these
other SKF publications, please contact
General
The primary function of lubrication is to prevent
damaging metal to metal contact at the various
sliding and rolling contact surfaces of the
bearing. Metal to metal contact causes excessive
rates of wear and can lead to premature bearing
failure. The secondary function of lubrication is
to protect the highly finished bearing surfaces
from rust and corrosion. Lubrication can also be
used to transfer heat from a bearing (circulating
oil) and provide additional sealing (grease).
SKF split pillow block housings are designed
to permit either grease, static oil bath, or
circulating oil lubrication of the bearings inside.
Most caps are drilled and tapped with two holes
located at 30 off vertical centerline. The hole
over the center of the housing is for the
lubrication of spherical roller bearings which
have the W33 feature (a groove and three holes
around the outer ring). The second of the two
holes is used for self-aligning ball bearings,
which do not have the W33 feature. The housing
bases are equipped with a drain hole on each
side to aid in removing old lubricants or serve
as an outlet for circulating oil. The reservoirs
inside the housings are designed so that they
maintain adequate quantities of either grease or
oil for reliable long-term operation.
At speeds within the bearing grease speed
rating and operating temperatures, which do not
exceed approximately 180 F, grease is the
simplest and most reliable form of lubrication.
Grease has the additional advantage of affording
excellent protection against rust and the
intrusion of dirt. Application systems for grease
are relatively simple and inexpensive when
compared to those for oil.
346
At higher speeds and temperatures, grease

relubrication intervals become unacceptably
short and oil lubrication is highly recommended.
Static oil baths and circulating oil systems can
be used with SKF split pillow blocks with little or
no modification to the blocks. Inlet and drain
holes appropriate for most oil lubricated
applications are standard on SKF split pillow
blocks, and oil sight glasses and other special
fittings can be provided. The level of the oil
should be at the center of the lowermost ball or
roller when the bearing is stationary. Refer to
the K dimension in the housing dimension
tables.
Circulating oil should be drained from both
side drains of the pillow block. The drain piping
must be adequately sized and arranged to allow
the free drainage of oil. Too high of an oil level,
or too large of a quantity of grease can result in
high operating temperatures due to churning
of the lubricant.
Lubrication
Grease
How does grease lubrication work?
Most greases consist of a lubricating oil (approx.
90%) suspended in a soap base (approx. 10%).
The latter merely acts to keep the oil in
suspension. When moving parts of a bearing
come in contact with the grease, a small
quantity of oil will adhere to the bearing
surfaces. Oil is therefore removed from the
grease near the rotating parts. The oil that is
picked up by the bearing is gradually broken
down by oxidation or lost by evaporation,
centrifugal force, etc. Bleeding of the grease
should therefore take place to continue to supply
a small quantity of oil, which is usually sufficient
for satisfactory operation. But, needless to say,
the bearing cannot function properly unless the
supply of oil keeps up with the demand. This
process cannot go on indefinitely. In time, the
grease will oxidize or the oil in the grease near
the rotating parts may be depleted.
When can grease be used?
For normally loaded applications, which operate
without the effects of outside heat sources and
where the bearings do not exceed the grease
speed rating, grease lubrication is most often
used. When loads are heavy, or bearings are
subject to external heat sources or other
extremes in ambient temperature, or speeds
exceed the bearing grease speed rating, a
bearing temperature analysis should be
conducted to verify that expected operating
temperatures are within acceptable limits,
typically less than 180 F. SKF Applications
Engineering can assist with this analysis.
What kind of grease should be used?

For most split pillow block applications, SKF
recommends the use of a high quality, NLGI
grade 1 or 2 consistency, lithium soap based
grease with a mineral base oil. Consistency
refers to the stiffness of a grease and is
classified according to the National Lubricating
Grease Institute (NLGI) of the United States.
Higher NLGI numbers correspond to stiffer
greases. In slow speed or low temperature
applications, an NLGI 2 may channel excessively
leaving the bearing without oil. In these
applications, it may be necessary to use a softer
grease, i.e. an NLGI 1 or 0. Please consult SKF
With respect to bearing lubrication, viscosity
is another characteristic of the grease that
should be evaluated. SKF Applications
Engineering can help you determine the
necessary viscosity at the bearing operating
temperature to prevent metal to metal contact
at the rolling contact surfaces. However, to
prevent metal to metal contact at the sliding
contact surfaces, the viscosity at the operating
temperature should be at least 21 cSt
(100 SUS) for spherical and toroidal (CARB) roller
bearings and at least 13 cSt (70 SUS) for ball
bearings. Note that the operating temperature
of the bearing is typically 10 to 20 F warmer
than the surface of the housing.
Although greases with soap bases other
than lithium are often successfully used in the
lubrication of bearings, it has been the
experience of SKF that lithium soaps offer the
best combination of high temperature stability,
resistance to water, and durability in split pillow
block applications. Greases with mineral base
oils have long been the recommended type
although synthetics, such as SHCs (synthetic
hydrocarbons), are starting to gain favor due to
their high temperature performance, i.e. they
have higher oxidation resistance. As a general
rule, greases with different soap bases,
consistencies, or base oil types should not be
mixed.
How much grease should be used?

For the majority of split pillow applications, at
installation, the base of the housing should be
packed 1/3 to 1/2 full and the bearing should be
filled with grease by working it in between the
rolling elements. As mentioned earlier, too much
grease can result in high operating temperatures
due to lubricant churning. For low speed
applications, which operate in a heavily
contaminated environment, the housing and
bearing can be filled 100% with grease to
provide additional sealing protection. The low
speed should preclude the danger of high
operating temperatures. For relubrication
quantities and intervals, refer to the appropriate
following sections.
Lubrication
Oil
How often should the oil be changed?
Circulating oil systems
SKF split pillow blocks are suitable for static oil

bath and circulating oil methods of lubrication.
Oil is generally used when high speeds or
operating temperatures preclude the use of
grease, when heat must be removed from the
bearing, or when surrounding components are
oil-lubricated.
The frequency at which the oil must be changed

is mainly dependent on the operating conditions
and on the quantity of oil used.
Where oil bath lubrication is employed it is
normally sufficient to change the oil once a year,
provided the bearing temperature does not
exceed 120 F (50 C) and there is no
contamination. Higher temperatures or more
arduous running conditions necessitate more
frequent changes, e.g. at a temperature of
220 F (110 C) the oil should be changed every
3 months. For circulating oil systems the period
between complete oil changes is dependent on
how often the oil is circulated over a given
period of time and whether it is cooled, etc. The
most suitable period can generally only be
determined by trial runs and frequent
examination of the oil. The same practice also
applies to oil jet lubrication.
Pressurized circulating oil, for auxiliary heat

removal allows higher operation, and prolongs
the life of the oil where operating conditions are
usually severe such as in high temperature
applications. Most commercial circulating oil
systems have components which filter and cool
the oil, creating the best possible operating
condition for the bearing.
Oil is introduced through one of the inlet
holes in the housing cap and drained from one
or both sides of the base. For spherical roller
bearings, oil should be put in through the center
hole in the cap and drained from both sides of
the base. For ball bearings and toroidal roller
(CARB) bearings, oil should be put in through
the offset hole in the cap and drained from the
opposite side of the base so that oil is forced to
go through the bearing before being outlet.
Drains should lead downward immediately
outside of the housing to prevent accumulation
of oil in the housing. Horizontal drains must
be avoided.
Additional considerations may be necessary
when using circulating oil. These can include
special seals, cross drillings in the housing,
wet sump requirements, flow rates, and
enlarging drain hole diameters. Please consult
SKF Applications Engineering concerning
these issues.
What kind of oil should be used?

SKF recommends the use of a good quality,
straight mineral oil without additives. The oil
should be resistant to oxidation and gumming
and obviously should not cause corrosion to any
bearing or housing components. Oils containing
additives for the improvement of certain
lubricant properties such as extreme pressure
behavior, aging resistance, anti-corrosion, etc.,
are generally only used in special cases.
Synthetic oils are generally only considered for
bearing lubrication in extreme cases, e.g. at very
low or very high operating temperatures. It
should be remembered that the lubricant film
formation when using a synthetic oil may differ
from that of a mineral oil having the same
viscosity. For information concerning EP
additives (in grease and oil), refer to the General
Catalog (6000EN).
Viscosity is another characteristic that should
be evaluated. SKF Applications Engineering can
again be used to determine the minimum
viscosity at the bearing operating temperature to
prevent metal to metal contact at the rolling
contact surfaces. However, to prevent metal to
metal contact at the sliding contact surfaces, the
viscosity at the operating temperature should be
at least 21 cSt (100 SUS) for spherical and toroidal
(CARB) roller bearings and at least 13 cSt (70
SUS) for ball bearings. Note that the operating
temperature of the bearing is typically 10 to
20 F warmer than the surface of the housing.
Oil bath
A simple oil bath is suitable for low and
moderate speed applications. The level of the oil
should be at about the center of the lowermost
ball or roller when the bearing is stationary.
The dimension for this is given in the dimension
tables as K. For higher speeds, the level should
be slightly lower to reduce the effects of
lubricant churning or about 1/8" above the corner
of the outer ring sphere of the bearing. An oil
sight glass must be used to monitor the oil level
during operation. It mounts into one of the drain
holes in the housing base. Additionally, for
higher speeds, SKF can supply special seals
which reduce oil leakage. SKF Applications
Engineering can assist with determining the best
sealing requirements.
The static oil level should be marked on the
sight glass at installation and a running level
should be marked immediately after start up.
Depending on the type of bearing and the speed
and direction of rotation, the running level will
either rise or fall from the static level.
347

Lubrication
Comparative advantages of oil and grease

Advantages of grease
Protection against moisture
1. Maintenance work is ordinarily reduced since there are

no oil levels to maintain and the addition of a new lubricant
is required less frequently.
No rolling bearing lubricant has been developed, which will

completely protect a bearing against moisture. However,
rolling bearings are frequently used with success where
moisture is present. The design of enclosures and
lubrication systems requires careful consideration.
Selection of the lubricant is important to minimize effects
of some moisture entry.
2. Grease in proper quantity is more easily confined to the

housing. Design of enclosures can therefore be
simplified.
3. Freedom from leakage is readily accomplished in food,
textile, chemical industries and where contamination of
products must be avoided.
4. Grease improves the efficiency of labyrinth enclosures
and offers better protection for the bearing.
5. The friction torque and temperature rise are usually
more favorable.
Advantages of oil
1. Oil is easier to drain and refill. This may be more
desirable for applications requiring short lubricating
intervals.
2. The correct amount of lubricant is more easily controlled.
3. Oil lends itself more readily to the lubrication of all parts
of a machine.
4. Oil lends itself to applications with higher temperatures.
348
Compounded oils are more water repellent than straight

mineral oils and are, therefore, better able to keep moisture
from the bearing surfaces. If, however, the oil is permitted to
oxidize, it will be more destructive to the bearing surfaces
when moisture is present.
A sodium-base grease will usually form a non-corrosive
emulsion when mixed with a limited quantity of water.
Agitation is necessary to form the emulsion. If water enters
the bearing while there is no agitation from rotation, the
bearing can become corroded. Because of the limited
tolerance to water and the potential damage while static,
sodium-base greases are losing favor to the water-repellent
quite-stable lithium-base greases. Of course, the waterrepellent grease must completely cover the bearing to
protect it and so, attention must be paid to the static
condition. Water-repellent grease is useful also in improving
efficiency of labyrinth seals.
Lubrication
Initial grease charge for split pillow block housings

The recommended initial grease charge (weight)
for split pillow block and bearing assemblies are
listed in the accompanying tables. Values apply
for spherical roller bearings, toroidal roller
(CARB) bearings and self-aligning ball bearing
units. The initial charge is intended to fill
approximately 1/2 of the free space in the
housing cavities and should be used for
applications operating at slow to moderate
speeds under 2/3 of the grease speed rating
shown in the bearing tables. For higher
operating speeds or applications running in
clean environments, the recommended initial
grease charge may be reduced by approximately
1
/3 in order to minimize churning. For operation
over the bearing grease speed ratings or less
than 10 rpm, consult SKF Applications
Engineering.
At initial assembly of the unit, spherical roller
bearings and self-aligning ball bearings should
be internally packed 100% around the cage and
rolling elements. Toroidal roller (CARB) bearings
should be filled approximately 50% full of grease
at installation with that grease being placed
under the cage totally filling the space between
the cage and inner ring. The remainder of the
grease should be applied to the side cavities in
the housing base and the labyrinth grooves of
the ring seals.
Initial grease charge for SAF pillow block assemblies

SAF
SAF
SAF
SAF
SAF
507
509
510
308
309
609
511
310
610
513
311
611
515
216
217
218
312
313
314
315
316
317
220
516
517
613
518
615
616
617
520
318
024
618
222
224
226
320
322
522
524
526
620
622
228
230
232
324
326
528
530
532
624
626
234
236
238
240
244
328
330
332
334
338
340
534
536
538
540
544
628
630
632
634
638
640
026
028
030
032
034
036
038
040
044
048
052
056
Initial charge
oz
lbs
2.5
3.0
4.0
4.5
5.0
5.0
6.5
7.5
8.0
9.0
10.0
13.0
13.0
14.0
14.0
16.0
20.0
21.0
22.0
28.0
40.0
314
314
314
334
414
414
514
6
714
812
1112
1512
349

Lubrication
Initial grease charge for SDAF pillow block assemblies (estimate)

SDAF
SDAF
219
220
316
317
318
319
320
322
222
224
226
228
230
232
234
236
238
240
244
324
326
328
330
332
334
336
338
340
SDAF
SDAF
520
616
617
618
522
524
526
528
530
532
534
536
538
540
544
620
622
Initial charge
oz
lbs
16
20
21
27
32
44
44
624
626
628
630
632
634
636
638
640
3
33/4
43/4
51/2
61/2
8
9
101/2
12
Initial grease charge for SAW pillow block assemblies (estimate)

SAW
SAW
220
222
224
226
228
230
323
234
236
238
240
244
520
522
524
526
528
530
532
534
536
538
540
544
Initial charge
oz
lbs
26
34
40
3
33/4
41/2
51/2
61/2
7
81/2
10
131/4
Initial grease charge for SDAF extended range pillow block assemblies (estimate)
SDAF extended range
3060
3064
3072
3076
3080
3084
3088
3092
3096
30/500
30/530
3152
3156
3160
3164
3168
3172
3176
3180
lbs
3248
3252
3256
3260
3264
3264
3268
3272
3276
3184
3188
3192
3196
3280
3284
3288
3292
3296
10
15
15
18
20
22
25
21
27
32
32
40
38
44
46
47
60
60
Due to the special engineering nature of these housings, please consult with SKF Applications Engineering for
custom lubrication recommendations.
350
Shaft fits / housing load ratings
Shaft fits for split pillow block housings

The values S-1, S-2, and S-3 can be found in
the product tables starting on page 358. The
bearing seat diameter should be selected from
the bearing fit tables in the Bearing Installation
and Maintenance Guide (SKF publication
# 140-710).
The following chart shows the recommended

shaft diameter tolerance for split pillow block
housings. S-1 refers to the shaft diameter for
an adapter mount bearing and S-2 & S-3 refer
to the shaft diameter under the seal for
cylindrical mounted bearings.
Shaft tolerance for split pillow block mountings
Nominal dia.
In
Over
Including
For adapter mounting
For cylindrical mounting
Dia. tolerance limits

In
Dia. tolerance limits

In
S-1
S-2 and S-3
/2
0.000
0.002
0.000
0.003
0.000
0.003
0.000
0.004
0.000
0.003
0.000
0.005
0.000
0.003
10
0.000
0.006
0.000
0.004
10
15
0.000
0.006
0.000
0.005
0.000
0.006
0.000
0.006
15
Housing loads for split pillow blocks

The selection of a rolling bearing pillow block
depends not only on determining adequate
service life of the bearing for the operating
conditions of the application, but also on the
adequacy of the housing to safely accommodate
the magnitude and characteristics of all applied
loading.
Split pillow blocks are designed for
predominantly vertical loads directed through
the base. If the load direction is otherwise,
care must be taken to see that the housing
selected has sufficient strength. It must have
an adequate factor of safety against fracture
and be properly assembled to carry the loading
involved.
Proper assembly techniques dictate that the
housing cap and base bolts be torqued to
achieve preload during installation, to avoid
elastic separation of the mating parts under
load and to resist gradual loosening over
time. To obtain full fatigue resistance of the

bolts, care in following recommended torque
requirements is of particular importance;
especially when the assembly is subjected to the
action of cyclic loading and dynamic imbalance.
The tabulations on pages 352-356 show the
approximate safe loading for different directions
of load. These guideline limits have been
established using accepted engineering practices
with consideration given to safety, ultimate
tensile strength of the materials used and
working stresses to reflect a safety factor of 5
against base fracture, and a minimum factor of
2 against cap bolt yield.
When the loading acts at an angle between 60

and 120, or if the axial direction exceeds 25%
of the P180 value shown in the tables, it is
recommended that the housing be doweled to
its mounting surface. Starting dimples are
provided on the feet of most housings, which
can be drilled for dowel pins. Alternatively, the
mounting surface may be provided with positive
stops or shear blocks to locate the housing in
the direction of load.
The maximum permissible axial loading that
can be safely carried by the pillow block
assembly depends on various considerations in
addition to the operational performance abilities
of the bearing. For a purely axial force under
static or dynamic conditions, the permissible
load on the pillow block casting should not
exceed 65% of P180. Additionally for adapter
mounted assemblies the axial load rating to
safely prevent slippage on the shaft can be
found in the tables on page 357.
351

Housing loads
SAF style cast-iron
(values in pounds force)
P 60
P 90
Pillow block housing designation

SAF
SAF
SAF
SAF
SAF
P 120
Style
P 60
P 150
Recommended safe loads

P 90
P 120
P 150
P 180
P 180
lbf
509
308
510
309
609
511
310
610
513
311
*311
312
*312
611
*611
515
*515
313
*313
216
*216
613
*613
516
*516
314
*314
217
*217
218
*218
517
*517
518
*518
315
*315
316
*316
317
*317
220
*220
024
*024
222
224
026
615
*615
616
*616
617
*617
520
*520
318
028
320
226
228
230
232
234
236
238
240
244
618
522
524
620
526
030/032 322
034
324
036/038 326
040
328
330
044
332
048
334
052
338
056
340
622
528
530
532
534
536
538
540
544
624
626
628
630
632
634
638
640
M5
A
M5
A
M5
A
M5
A
A
A
A
M5
M5
A
A
M5
M5
A
A
M5
M5
M5
M5
A
A
A
A
A
A
M5
M5
A
M5
M5
A
M5
A
M5
A
A
A
A
A
A
A
A
4700
7300
6500
7900
10100
8800
11300
9700
8000
11100
9500
17000
12200
18700
13600
18700
13600
20800
20800
19000
13800
27200
22800
27200
22800
19300
20800
21200
23300
30500
26700
28800
33400
41700
41700
42500
42500
55900
51700
50900
52600
52600
65100
81800
95100
101000
Cap bolt information

Cap bolt
Torque
(no.) size
in
2800
4400
3900
4700
6100
5300
6800
5800
4800
6700
5700
10200
7300
11200
8100
11200
8100
12500
12500
11400
8300
16300
13700
16300
13700
11600
12500
12700
14000
18300
16000
17300
20000
25000
25000
25500
25500
33500
31000
30500
31500
31500
39000
49000
57000
61000
1700
2800
2500
3000
3900
3200
4000
3600
3000
4100
3500
6300
4500
6800
4900
6800
4900
7800
7800
7100
5200
10200
8600
10200
8600
7200
7600
8000
8800
11400
10000
11000
12500
16300
16300
16600
16600
21200
19600
19300
19300
19000
24000
30500
36000
38000
1500
2500
2200
2700
3500
2900
3600
3300
2700
3700
3100
5700
4100
6000
4400
6000
4400
6900
6900
6400
4700
9100
7800
9100
7800
6500
6900
7200
8000
10400
9000
10000
11400
15000
15000
15300
15300
19300
18000
17600
17300
17000
21200
27000
32500
34000
1800
3100
2800
3300
4300
3500
4300
4000
3200
4500
3800
6800
5000
7100
5200
7100
5200
8500
8500
7800
5700
11200
9500
11200
9500
7800
8300
8600
9600
12500
11000
12200
13700
18300
18300
19000
19000
23200
21600
21200
20800
20000
25500
32500
39000
41500
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
ft-lbs
7/16-14
1/2-13
7/16-14
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
1/2-13
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
3/4-10
3/4-10
3/4-10
3/4-10
3/4-10
3/4-10
3/4-10
3/4-10
1-8
1-8
1-8
1-8
1-8
3/4-1
3/4-10
3/4-10
3/4-10
7/8-9
7/8-9
1-8
1 1/2-6
*When the bearing housing can be supplied with either a two- or four-bolt base, the asterisk indicates allowable loads for the four-bolt base option
Grade 5 cap bolt torques are based on manufacturing processes. Increased tightening torques may be required for critical applications.
Consult SKF Applications Engineering for further details.
352
SAE
grade
45
110
45
110
60
110
60
110
110
110
110
60
60
220
220
110
110
220
220
110
110
110
110
220
220
380
380
380
380
150
150
380
150
295
900
295
900
295
380
380
380
380
600
600
900
870
5
8
5
8
5
8
5
8
8
8
8
5
5
8
8
5
5
8
8
5
5
5
5
8
8
8
8
8
8
5
5
8
5
5
8
5
8
5
8
8
8
8
8
8
8
2
Housing loads
SAFS style cast-steel
P 60
P 90

SAFS
SAFS
SAFS
SAFS
SAFS
P 120
Style
P 60
P 150

P 90
P 120
P 150
P 180
P 180
lbf
216
*216
217
*217
218
*218
220
*220
222
224
226
515
*515
516
*516
517
*517
518
*518
520
*520
522
524
024
*024
026
028
030
032
320
322
228
526
620
622
528
034
230
232
234
238
238
240
244
036
038
040
044
048
052
056
324
326
530
532
624
626
328
330
332
334
338
340
534
536
538
540
544
628
630
632
634
638
640
L
L
L
L
L
L
N
N
N
N
N
M7
N
N
N
N
N
N
N
N
N
L
N
N
N
N
23300
17000
31000
31000
17700
18700
31700
35400
31700
39400
40000
55900
55900
69300
69300
67600
67600
88500
77600
77600
77600
120200
93500
125200
155300
150300

Cap bolt
Torque
(no.) size
in
13400
10200
18600
18600
10600
11200
19000
21200
19000
23600
24000
33500
33500
41500
41500
40500
40500
53000
46500
46500
46500
72000
56000
75000
93000
90000
8300
6400
11200
11200
6500
7100
12000
13400
11800
14600
15000
21200
21200
28000
28000
26000
26000
33500
30000
30000
28500
44000
34000
46500
58500
56000
7500
5700
10000
10000
6000
6400
10800
12200
10800
13200
13400
19600
19600
26500
26500
23600
23600
30500
27000
27000
25500
39000
30500
41500
53000
50000
9000
6900
11800
11800
7200
7600
13200
14600
12900
16000
16300
24000
24000
34000
34000
28500
28500
36500
32500
32500
30000
45500
36000
50000
64000
60000
(2)
(2)
(2)
(2)
(2)
(2)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(2)
(4)
(4)
(4)
(4)
SAE
grade
ft-lbs
1/2-13
1/2-13
5/8-11
5/8-11
5/8-11
5/8-11
1/2-13
1/2-13
5/8-11
5/8-11
5/8-11
5/8-11
5/8-11
3/4-10
3/4-10
7/8-9
7/8-9
7/8-9
7/8-9
7/8-9
1-8
1 3/8-6
1 1/8-7
1 1/4-7
1 1/2-6
1 1/2-6
110
110
220
220
220
220
110
110
220
220
220
220
220
380
380
600
600
600
600
600
900
2380
1280
1820
3160
3160
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
*When the bearing housing can be supplied with either a two- or four-bolt base, the asterisk indicates allowable loads for the four-bolt base option
SAF A-style
Taking advantage of technological advances in
design and manufacturing the SAF A-style
housing offers a high mechanically efficient
design having significantly improved upward load
capacity for greater safety and reliability with a
minimum of material weight. Of modern
functional appearance, and a choice of 2- or 4bolt mounting variations, the SAF A housing
interchanges with previous designs and complies
with all industry mounting dimensions.
In addition to its superior upward strength,
the following features have been added:
Pry slots for easier cap removal
All cap bolts supplied of heat treated, high
tensile material for improved strength and
maximum safety
Large sump design for use with either

grease or oil
Flat square foot for proper base bolt
seating and proper assembly alignment
during installation
Cast-in dimples in the base for dowel pin
drilling during field installations
SAF L-style
The SAF L-style is the classic 2-bolt cap design,
which established the SAF interchange
dimensions within the industry.
SAF N-style
The SAF N-style is a rugged, 4-bolt cap design
available only in the largest SAFS sizes where
the cast-in lifting grips on each side of the cap
provide ease of handling whether manually or
with a sling.
SAF M5-style
The SAF M5 style incorporates modern
technology to optimize its design, thus offering
high mechanical efficiency while reducing the
housing weight. The optimized foot design
removes the old gussets and still maintains
housing strength. The sump has been
maximized and is suitable for grease or oil
lubrication, while the cast-in oil drain back
feature reduces leakages. The newly designed
under-coring allows for uniform material cooling
when cast, while the foot hole and center cross
supports improve housing bore roundedness.
Additionally, SKF has patented a grease guiding
system for side lubrication.
353

Housing loads
SAW style cast-iron
P 60

SAW
P 90
Style
P 120

P 60
P 90
P 120
P 150
P 150
P 180
lbf
520
526
528
538
540
544
354
A
A
N
A
A
A
26720
42585
43420
65130
81830
95190
P 180

Cap bolt
Torque
(no.) size
in
16000
25500
26000
39000
49000
57000
10000
16600
16600
24000
30500
36000
9000
15300
15000
21200
27000
32500
1100
19000
18300
25500
32500
39000
(2)
(2)
(4)
(4)
(4)
(4)
SAE
grade
ft-lbs
3
/4-10
1-8
/8-9
7
/8-9
7
/8-9
1-8
7
380
900
165
600
600
900
8
8
2
8
8
8
Housing loads
SDAF style cast-iron
Housing loads
SDAFS cast-steel
P 60
P 90

SDAF
SDAF
SDAF
SDAF
SDAF
P 120
P 150

P 60
P 90
P 120
P 150
P 180
lbf
220
222
224
226
230
232
236
238
240
244
317
318
320
322
324
326
330
332
334
336
338
340
520
522
524
526
530
532
536
538
540
544
617
618
620
622
624
626
630
632
634
636
638
640
40080
45925
51770
54000
60120
85170
83500
90180
127755
150300
141950
152805
144455
P 180

Cap bolt
Torque
(no.) size
in
24000
27500
31000
36500
36000
51000
50000
54000
76500
90000
85000
91500
86500
15000
17300
19600
23600
23600
32000
31500
32500
47500
56000
53000
57000
54000
13700
16000
17600
21600
21600
29000
28500
29000
43000
50000
48000
52000
49000
16600
19300
21200
26500
27000
35500
34500
34500
52000
60000
57000
63000
58500
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
SAE
grade
ft-lbs
3
/4-10
/4-10
/8-9
7
/8-9
7
/8-9
11/8-7
11/8-7
11/4-7
11/4-7
11/4-7
13/8-6
13/8-6
13/8-6
3
7
175
175
165
165
165
350
350
500
500
500
660
660
660
2
2
2
2
2
2
2
2
2
2
2
2
2
NOTE: A higher safe load may be achieved by using high-tensile cap bolts of SAE grade 5 or higher; consult SKF Applications Engineering for this variation

SDAFS
SDAFS
SDAFS
SDAFS
SDAFS

P 60
P 90
P 120
P 150
P 180
lbf
222
224
226
232
236
238
240
244
320
322
326
330
332
334
336
338
340
522
524
526
532
536
538
540
544
620
622
626
630
632
634
636
638
640
81830
95190
88510
130260
141950
203740
238810
228790
250500
228790

Cap bolt
Torque
(no.) size
in
49000
57000
53000
78000
85000
122000
143000
137000
150000
137000
30500
36500
34500
49000
51000
75000
88000
85000
95000
85000
27500
33500
32000
44000
45500
68000
80000
76500
85000
76500
33500
41500
40000
54000
54000
81500
95000
91500
102000
93000
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
SAE
grade
ft-lbs
7
/8-9
/8-9
/8-9
11/8-7
11/4-7
11/4-7
11/4-7
13/8-6
13/8-6
13/8-6
7
7
600
600
600
1280
1820
1820
1820
2380
2380
2380
8
8
8
8
8
8
8
8
8
8
355

Housing loads
SDAF cast-iron
P 60
Pillow block designation

SDAF
SDAF
SDAF
P 90
P 120
Recommended safe loads (class 40 cast-iron)

P 60
P 90
P 120
P 150
P 150
P 180
P 180
P axial
lbf
3060
3064
3068
3072
3076
3080
3084
3088
3092
3096
30/500
30/530
in
ft-lbs
SAE
grade
3152
3156
3160
3160
3164
3248
3252
3256
3256
3260
294000
408000
176000
245000
110000
156000
98000
143000
118000
176000
76500
114000
(4) 11/2-6
(4) 11/2-6
1950
1950
5
5
442000
265000
170000
153000
186000
120000
(4) 13/4-5
2280
3168
3172
3176
3180
3264
3268
517000
650000
310000
390000
200000
245000
186000
224000
228000
275000
148000
180000
(4) 17/8-5
(4) 13/4-5
2860
2280
5
5
3272
3276
3280
717000
430000
275000
250000
305000
198000
(4) 17/8-5
2860
1050000
630000
405000
375000
465000
302000
(4) 2-41/2
3440
900000
540000
345000
320000
400000
260000
(4) 21/4-41/2
5030
3184
3188
3192
3196
3284
3288
SDAF extended range pillow blocks are designed

to predominantly support vertical loads directly
through the housing base. In this general
direction, the permissible load carrying ability of
the pillow block assembly is dependent solely on
the bearing. The standard engineering material
for all extended range housings is class 40 castiron to ASTM A48B, which provides high load
capability at an economical cost for most heavy
industrial applications. However, if the load
direction is not perpendicular to the base,
engineering care should be taken to assure that
the housing selection, which includes the choice
of material, will provide adequate strength to
assure factor of safety against fracture or yield.
For these custom assemblies, SKF offers
alternate cast-steel and ductile-iron materials
for improved impact resistance and strength.
356

Cap bolt
Torque
(no.) size
The tabulation above shows the recommended

safe loads for extended range housing for
nominal directions of loading. These guidelines
refer to class 40 cast-iron material and have
been established using accepted engineering
practices with full consideration given to safety,
the ultimate tensile strength of the material, and
working stresses to reflect a safety factor of 5
for the pillow block casting, and a minimum
factor of 2 on the cap bolts.
To determine the improved loading
capabilities with alternate materials, the values
in the tabulation may be multiplied by the factor
1.2 for cast-steel, or the factor 1.5 for ductileiron. All cast-steel and ductile-iron assemblies
are additionally equipped with SAE grade 8 cap
bolts to fully accommodate these higher load
carrying potentials.
When the application loading acts at an angle

between 60 and 120, or if the axial direction
exceeds 25% of the P180 value shown in the
table, it is recommended that the housing be
doweled to its mounting surface. Alternatively,
the mounting surface may be provided with
positive stops or shear blocks to locate the
housing in the direction of load. It is
recommended that SKF Applications Engineering
be contacted for complete review of load
carrying abilities and mounting requirements.
Permissible axial load rating for adapter mounted pillow blocks

The full axial load carrying ability of an adapter

mounted pillow block assembly is dependent
upon the friction fit between the adapter sleeve
and the shaft. Provided that the bearing is
properly mounted in accordance with the SKF
approved mounting method, the permissible
axial holding power for adapter mountings are
shown in the table below.
Shaft
dia.
S-1
Bearing
size2
SAF 15
in
17/16
111/16
115/16
23/16
27/16
211/16
215/16
33/16
37/16
315/16
43/16
47/16
415/16
53/16
57/16
515/16
67/16
615/16
73/16
715/16
815/16
97/16
107/16
1015/16
1115/16
127/16
137/16
1315/16
15
153/4
161/2
17
18
181/2
191/2
Safe axial load1

SAF 225
SDAF 225
SAW 235
SAF 16
SAF 226
SDAF 226
SAF 230
SDAF extended range

230
231
232
lbf
09
10
11
13
15
16
17
18
20
22
24
26
28
30
32
34
36
38
40
44
48
52
56
60
64
68
72
76
80
84
88
92
96
/500
/530
570
670
780
1000
1270
1400
1600
695
780
930
1370
1560
1760
2080
2450
3100
3900
4650
5600
6400
7350
8650
9800
10400
11800
13200
16000
4070
5180
6150
7010
8310
9710
11200
12600
13600
15400
17300
21400
765
915
1080
1460
1860
2120
2360
2600
3150
3750
1100
1340
1560
2120
2800
3150
3450
3900
4900
6000
6950
8150
9650
11000
12200
13700
15300
17000
18600
3750
4550
5000
5700
6400
7650
9000
9650
11000
13400
15000
18300
20000
24000
26000
30500
32500
34500
40000
42500
46500
50500
53000
56000
66000
25000
27500
32000
38000
43500
46500
49500
54000
63000
67000
74500
80000
26000
30500
33000
39000
45000
51000
56000
61500
69000
77000
83000
1Applies for both cast-iron and cast-steel housings

2Last two figures in bearing designation
357

Ball bearing / cylindrical mount
SAF 1300
Two-piece cast-iron housing
Self-aligning / 1300 series bearing
Held or free bearing
Oil or grease lubrication
LER / LOR triple ring seals
How to order
SAF 1320
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seals
Taconite seal
Cast-steel
FSAF 1320
SAF 1320Y
SAF 1320TLC
SAF 1320T
SAFS 1320
Held and free: Specify the appropriate stabilizing rings for a held unit; two required. Discard the enclosed stabilizing ring.
For shaft diameter tolerances see page 351; for bearing information see page 81; for other seal speed limits see pages 339-342.
Shaft
Designations
dia.
Complete
pillow block
da
S-2
mm
in
S-3
Bearing Bearing
basic load
rating
dynamic
C
lbs
LER/LOR Lockgrease nut

speed
limit
Lock- Pillow
washer block
housing
Stab.
ring
(2 reqd)
Mass
Triple ring
seal
S-2 shaft
(1 reqd)
End
plug
S-3 shaft
(1 reqd)
Taconite
seal
S-2
S-3
r/min
lbs
40
11516 1716 SAF 1308
1308E
7 600
6 700
N 08
W 08
SAF 308 SR 1608 LER 24
LER 17
EPR 3
TER 24
TER 17
14
45
218 11116 SAF 1309
1309E
8 770
6 300
N 09
W 09
SAF 309 SR 1609 LER 28
LER 20
EPR 4
TER 28
TER 20
18
50
238 178 SAF 1310
1310E
9 800
5 600
N 10
W 10
SAF 310 SR 1610 LER 35
LER 23
EPR 5
TER 35
TER 23
21
55
2916 2116 SAF 1311
1311E 11 400
5 000
N 11
W 11
SAF 311 SR 1611 LER 40
LER 27
EPR 6
TER 40
TER 27
25
60
278 214 SAF 1312
1312E 13 200
4 500
N 12
W 12
SAF 312 SR 1612 LOR 47
LOR 33
EPR 7
TER 47
TER 33
29
65
3116 2716 SAF 1313
1313E 14 600
4 300
N 13
W 13
SAF 313 SR 1613 LOR 55
LOR 37
EPR 7
TER 55
TER 37
35
70
314 258 SAF 1314
1314
16 700
4 000
N 14
W 14
SAF 314 SR 1614 LOR 64
LOR 43
EPR 8
TER 64
TER 43
40
75
3716 21316 SAF 1315
1315
17 800
3 800
AN 15 W 15
SAF 315 SR 1615 LOR 79
LOR 46
EPR 8
TER 79
TER 46
44
80
358 3
SAF 1316
1316
19 900
3 600
AN 16 W 16
SAF 316 SR 1616 LOR 84
LOR 60
EPR 10 TER 84
TER 60
63
85
31516 3316 SAF 1317
1317
21 900
3 400
AN 17 W 17
SAF 317 SR 1617 LOR 109
LOR 188 EPR 11 TER 109 TER 188
66
90
418 338 SAF 1318
1318
26 300
3 200
AN 18 W 18
SAF 318 SR 1618 LOR 112
86
100
412 31316 SAF 1320
1320
32 200
2 800
AN 20 W 20
SAF 320 SR 1620 LOR 118
97
110
478 4316 SAF 1322
1322
36 600
2 400
AN 22 W 22
SAF 322 SR 1622 LOR 121
LOR 113 EPR 14 TER 121 TER 113 132
Sizes SAF 1308 - SAF 1310, two-bolt base only;

Sizes SAF 1311 - SAF 1317, two-or four-bolt base options;
Sizes SAF 1318 - SAF 1322, four-bolt base only.
Optional internal radial clearances (e.g. C3) are available upon request.
358
Ball bearing / cylindrical mount
Held
Held
Free
Free
SAF 1300
Taconite seal option
How to order
SAF 1320
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seals
Taconite seal
Cast-steel
FSAF 1320
SAF 1320Y
SAF 1320TLC
SAF 1320T
SAFS 1320
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(no. reqd)
T2
T3
in
SAF 1308
212
814
238
612
41316
1732
(2)-12
1164
312
3932
SAF 1309
234
958
234
778
738
51516
1516
414
(2)-58
1116
3916
3916
SAF 1310
1058
234
118
734
51316
1716
458
(2)-58
1532
334
334
SAF 1311
314
11
318
1316
912
818
6316
112
(2)-58, (4)-12
1316
378
378
SAF 1312
314
1114
318
1316
958
858
178
638
138
514
(2)-58, (4)-12
114
4332
4116
SAF 1313
312
13
312
114
11
958
218
61932
1716
5516
(2)-34, (4)-58
11132
418
418
SAF 1314
334
13
312
114
11
978
218
738
1916
538
(2)-34, (4)-58
138
4532
418
SAF 1315
1334
378
158
1158
1038
218
7916
11116
578
(2)-34, (4)-58
11532
412
412
SAF 1316
414
1414
378
134
1258
1058
218
814
11316
612
(2)-34, (4)-58
112
41932
41932
SAF 1317
412
1514
438
134
1318
1158
238
834
178
634
(2)-78, (4)-34
1916
41116
41932
SAF 1318
434
1512
438
1312
12
214
914
678
(4)-34
11116
434
41932
SAF 1320
514
1612
434
218
1412
1314
234
10316
2316
738
(4)-34
12732
SAF 1322
1838
514
238
16
1458
314
11516
212
818
(4)-78
11516
514
538
359

Ball bearing / adapter mount
SAF 1500
Self-aligning / 1200 K series bearing
H
How to order
SAF 1515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seals
Taconite seals
Optional shaft size
Cast-steel
FSAF 1515
SAF 1515Y
SAF 1515TLC
SAF 1515T
SAF 1515 x 212
SAFS 1515
A
D
E
B
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional*
in
Bearing
basic load
rating
dynamic
C
LER / LOR
grease
speed
limit
lbs
r/min
Adapter
assembly
Pillow
block
housing
Mass
Stab.
ring
(no. reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
1316
SAF 1507
1207 EK
4 270
9 000
SNW 7
SAF 507
(1) SR 7-6
LER 14
EPR 2
TER 14
1716
138, 112
SAF 1509
1209 EK
5 150
7 500
SNW 9
SAF 509
(1) SR 9-0
LER 17
EPR 3
TER 17
11
11116
158, 134
SAF 1510
1210 EK
5 960
7 000
SNW 10
SAF 510
(1) SR 10-8
LER 20
EPR 4
TER 20
12
11516
178, 2
SAF 1511
1211 EK
6 210
6 300
SNW 11
SAF 511
(1) SR 11-9
LER 24
EPR 5
TER 24
16
2316
218, 214
SAF 1513
1213 EK
7 890
5 300
SNW 13
SAF 513
(2) SR 13-0
LER 29
EPR 6
TER 29
22
2716
238, 212
SAF 1515
1215 K
8 770
4 800
SNW 15
SAF 515
(2) SR 15-0
LOR 37
EPR 7
TER 37
27
21116
258, 234
SAF 1516
1216 K
8 930
4 500
SNW 16
SAF 516
(2) SR 1516
LOR 44
EPR 8
TER 44
36
21516
21316, 278, 3
SAF 1517
1217 K
11 000
4 000
SNW 17
SAF 517
(2) SR 1517
LOR 53
EPR 9
TER 53
37
3316
3116, 318, 314 SAF 1518
1218 K
12 900
3 800
SNW 18
SAF 518
(2) SR 1518
LOR 188
EPR 11
TER 188
45
3716
3516, 338, 312 SAF 1520
1220 K
15 500
3 400
SNW 20
SAF 520
(2) SR 1520
LOR 102
EPR 12
TER 102
59
31516
31316, 378, 4
1222 K
19 900
3 000
SNW 22
SAF 522
(2) SR 1522
LOR 109
EPR 13
TER 109
69
SAF 1522
*Requires different adapter sleeve and seals.

Size SAF 1522, four-bolt base only.
360
SAF 1500
Fixed
X
X
S-1
S-1
Float
K
K
How to order
SAF 1515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seals
Taconite seals
Optional shaft size
Cast-steel
FSAF 1515
SAF 1515Y
SAF 1515TLC
SAF 1515
SAF 1515 x 238
SAFS 1515
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
3316
(2)-12
13
16
3132
16
3132
in
SAF 1507
712
13
618
558
334
SAF 1509
214
814
238
13
614
438
358
(2)-12
15
SAF 1510
212
814
238
15
612
434
118
358
(2)-12
1164
314
SAF 1511
234
958
234
15
778
738
5132
114
378
(2)-58
1132
338
SAF 1513
11
318
912
818
52132
1316
412
(2)-58
1964
358
SAF 1515
314
1114
318
118
958
858
178
618
114
41116
(2)-58, (4)-12
1732
31316
SAF 1516
312
13
312
114
11
958
218
61932
1516
5516
(2)-34, (4)-58
114
418
SAF 1517
334
13
312
114
11
978
218
718
1716
(2)-34, (4)-58
1516
32932
SAF 1518
1334
378
158
1158
1038
218
7916
112
578
(2)-34, (4)-58
134
4116
SAF 1520
412
1514
438
134
1318
1158
238
81532
12132
618
(2)-78, (4)-34
15964
438
SAF 1522
41516
1612
434
1412
1258
234
91132
12532
612
(4)-34
218
4916
16
16
16
16
16
16
16
16
361

SAF 1600
How to order
SAF 1615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 1615
SAF 1615Y
SAF 1615TLC
SAF 1615T
SAF 1615 x 2
SAFS 1615
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional*
in
Bearing
basic load
rating
dynamic
C
LER / LOR
grease
speed
limit
lbs
r/min
Adapter
assembly
Pillow
block
housing
Mass
Stab.
ring
(2 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
1716
138, 112
SAF 1609
1309 EK
8 770
6 300
SNW 9
SAF 609
SR 1609
LER 17
EPR 3
TER 17
19
11116
158, 134
SAF 1610
1310 EK
9 800
5 600
SNW 10
SAF 610
SR 1610
LER 20
EPR 4
TER 20
22
11516
178, 2
SAF 1611
1311 EK
11 400
5 000
SNW 11
SAF 611
SR 1611
LER 24
EPR 5
TER 24
27
2316
218, 214
SAF 1613
1313 EK
14 600
4 300
SNW 13
SAF 613
SR 1613
LOR 32
EPR 7
TER 32
38
2716
238, 212
SAF 1615
1315 EK
17 800
3 800
SNW 15
SAF 615
SR 1615
LOR 37
EPR 7
TER 37
47
21116
258, 234
SAF 1616
1316 K
19 900
3 600
SNW 16
SAF 616
SR 1616
LOR 44
EPR 8
TER 44
66
21516
21316, 278, 3
SAF 1617
1317 K
21 900
3 400
SNW 17
SAF 617
SR 1617
LOR 184
EPR 10
TER 184
69
3316
3116, 318, 314 SAF 1618
1318 K
26 300
3 200
SNW 18
SAF 618
SR 1618
LOR 188
EPR 11
TER 188
91
3716
31516, 338, 312 SAF 1620
1320 K
32 200
2 800
SNW 20
SAF 620
SR 1620
LOR 102
EPR 12
TER 102
101
31516
31316, 378, 4
1322 K
36 600
2 400
SNW 22
SAF 622
SR 1622
LOR 109
EPR 13
TER 109
138
SAF 1622

362

SAF 1600
How to order
SAF 1615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 1615
SAF 1615Y
SAF 1615TLC
SAF 1615T
SAF 1615 x 2
SAFS 1615
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
958
234
778
738
5516
1516
414
(2)-58
1116
338
(No. reqd)
in
SAF 1609
234
SAF 1610
1058
234
118
734
51316
1716
458
(2)-58
1532
334
SAF 1611
314
11
318
1316
912
818
6316
112
478
(2)-58, (4)-12
1316
378
SAF 1613
312
13
312
114
11
958
218
61932
1716
5516
(2)34, (4)-58
11132
418
SAF 1615
1334
378
158
1158
1038
218
7916
11116
578
(2)-)34, (4)-58
11532
41332
SAF 1616
414
1414
378
134
1258
1058
218
814
11316
612
(2)-)34, (4)-58
112
41932
SAF 1617
412
1514
438
134
1318
1158
238
834
178
634
(2)-78, (4)-34
1916
4916
SAF 1618
434
1512
438
1312
12
214
9316
678
(4)-34
11116
4916
SAF 1620
514
1612
434
218
1412
1314
234
10316
2316
7516
(4)-)34
12732
SAF 1622
1838
514
238
16
1458
314
11516
212
818
(4)-78
11516
538
363

Spherical roller / cylindrical mount
SAF 22200
LOR triple ring seals
H
How to order
SAF 22215
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF 22215
SAF 22215Y
SAF 22215TLC
SAF 22215T
SAFS 22215
A
D
E
B
Held and free: Standard and standard option blocks come with an enclosed stabilizing ring. For a free unit, discard the enclosed stabilizing ring.
Designations
Shaft
dia.
Complete
pillow block
da
S-2 S-3
mm
in
Bearing
Bearing
basic load
rating
dynamic
C
LOR
grease
speed
limit
lbs
r/min
Locknut
Lock- Pillow
washer block
housing
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
65
3116 2716 SAF 22213 22213 E
43 400
3 800
N 13
W 13
SAF 213 SR 13-0
LOR 55
LOR 37
EPR 7
TER 55
TER 37
22
75
3716 21316 SAF 22215 22215 E
47 700
3 400
AN 15 W 15
SAF 215 SR 15-0
LOR 79
LOR 46
EPR 8
TER 79
TER 46
27
80
358 3
53 100
3 200
AN 16 W 16
SAF 216 SR 16-13 LOR 82
LOR 54
EPR 9
TER 82
TER 54
34
85
31516 3316 SAF 22217 22217 CC/W33
55 100
3 000
AN 17 W 17
SAF 217 SR 17-14 LOR 89
LOR 63
EPR 9
TER 89
TER 63
35
90
418 338 SAF 22218 22218 CC/W33
65 200
2 600
AN 18 W 18
SAF 218 SR 18-15 LOR 112
44
100
412 31316 SAF 22220 22220 CC/W33
81 000
2 200
AN 20 W 20
SAF 220 SR 20-17 LOR 118
75
110
478 4316 SAF 22222 22222 CC/W33 105 000
2 000
AN 22 W 22
SAF 222 SR 22-19 LOR 121
68
120
5516 4916 SAF 22224 22224 CC/W33 121 000
1 900
AN 24 W 24
SAF 224 SR 24-20 LOR 127
97
130
578 41516 SAF 22226 22226 CC/W33 142 000
1 800
AN 26 W 26
SAF 226 SR 26-0
LOR 136
134
140
614 5516 SAF 22228 22228 CC/W33 160 000
1 700
AN 28 W 28
SAF 228 SR 28-0
LOR 144
141
150
658 534 SAF 22230 22230 CC/W33 191 000
1 600
AN 30 W 30
SAF 230 SR 30-0
LOR 151
181
160
6116 SAF 22232 22232 CC/W33 225 000
1 500
AN 32 W 32
SAF 232 SR 32-0
LOR 156
199
170
7716 6716 SAF 22234 22234 CC/W33 252 000
1 300
AN 34 W 34
SAF 234 SR 34-0
LOR 161
263
180
71316 678 SAF 22236 22236 CC/W33 265 000
1 300
AN 36 W 36
SAF 236 SR 36-30 LOR 165
286
190
838 714 SAF 22238 22238 CC/W33 286 000
1 200
AN 38 W 38
SAF 238 SR 38-32 LOR 171
356
200
834 758 SAF 22240 22240 CC/W33 328 000
1 100
AN 40 W 40
SAF 240 SR 40-34 LOR 175
408
220
9916 8516 SAF 22244 22244 CC/W33 396 000
950
N 44
SAF 244 SR 44-38 LOR 179
535
SAF 22216 22216 E
Size SAF 22213, two-bolt base only;

364
W 44
T3
T2
SAF 22200
Fixed
X
S-3
S-2
S-2 da
S-3
Float
K
K
How to order
SAF 22215
Option
Specify
Four-Bolt Base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF 22215
SAF 22215Y
SAF 22215TLC
SAF 22215T
SAFS 22215
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
T2
T3
in
SAF 22213
11
318
912
818
52132
412
16
(2)-58
114
334
334
SAF 22215
314
1114
318
118
958
858
178
618
41116
16
(2)-58, (4)-12
1932
378
378
SAF 22216
312
13
312
114
11
958
218
61932
114
5516
16
(2)-34, (4)-58
11532
418
4332
SAF 22217
334
13
312
114
11
978
218
718
138
16
(2)-34, (4)-58
1916
32932
32932
SAF 22218
1334
378
158
1158
1038
218
7916
112
578
16
(2)-34, (4)-58
134
4316
4332
SAF 22220
412
1514
438
134
1318
1158
238
81532
12132
618
16
(2)-78, (4)-34
15964
4516
4516
SAF 22222
41516
1612
434
1412
1258
234
91132
12532
612
16
(4)-34
218
412
4916
SAF 22224
514
1612
434
218
1412
1314
234
10316
12732
738
16
(4)-34
2932
SAF 22226
1838
514
238
16
1458
314
11516
21132
818
16
(4)-78
21532
514
5516
SAF 22228
2018
578
238
1718
16
338
1134
2132
758
16
(4)-1
23964
518
518
SAF 22230
6516
2114
614
212
1814
17
334
1212
838
16
(4)-1
24964
512
512
SAF 22232
61116
22
614
258
1914
1738
334
13516
2116
834
16
(4)-1
23132
51116
51116
SAF 22234
7116
2434
634
234
2158
1938
414
14316
2532
958
16
(4)-1
318
6316
SAF 22236
712
2634
718
2358
2078
458
1478
238
10
16
(4)-1
3964
614
614
SAF 22238
778
28
712
318
2438
2158
412
151116
2716
1034
16
(4)-114
31964
7716
61316
SAF 22240
814
2912
338
25
2212
1612
21532
1114
16
(4)-114
312
71116
7116
SAF 22244
912
3234
834
334
2778
2434
514
1858
318
12
(4)-112
358
8116
16
365

SAF 22300
How to order
SAF 22315
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF 22315
SAF 22315Y
SAF 22315TLC
SAF 22315T
SAFS 22315
Designations
Shaft
dia.
Complete
pillow block
da
S-2
mm
in
Bearing
S-3
Bearing
basic load
rating
dynamic
C
LER / LOR Lockgrease nut

speed
limit
lbs
r/min
Lock- Pillow
washer block
housing
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
40
11516 1716 SAF 22308 22308 E
33 700 4 500
N 08
W 08
SAF 308 SR 10-8
LER 24
LER 17
EPR 3
TER 24
TER 17
15
45
218 11116 SAF 22309 22309 E
41 200 3 800
N 09
W 09
SAF 309 SR 11-9
LER 28
LER 20
EPR 4
TER 28
TER 20
19
50
238 178 SAF 22310 22310 E
49 500 3 400
N 10
W 10
SAF 310 SR 0-10
LER 35
LER 23
EPR 5
TER 35
TER 23
22
55
2916 2116 SAF 22311 22311 E
60 700 3 200
N 11
W 11
SAF 311 SR 13-11 LER 40
LER 27
EPR 6
TER 40
TER 27
27
60
278 214 SAF 22312 22312 E
69 700 3 000
N 12
W 12
SAF 312 SR 15-12 LOR 47
LOR 33
EPR 7
TER 47
TER 33
31
65
3116 2716 SAF 22313 22313 E
76 500 2 600
N 13
W 13
SAF 313 SR 16-13 LOR 55
LOR 37
EPR 7
TER 55
TER 37
38
70
314 258 SAF 22314 22314 CC/W33
79 900 2 400
N 14
W 14
SAF 314 SR 17-14 LOR 64
LOR 43
EPR 8
TER 64
TER 43
42
75
3716 21316 SAF 22315 22315 CC/W33
90 000 2 200
AN 15 W 15
SAF 315 SR 18-15 LOR 79
LOR 46
EPR 8
TER 79
TER 46
48
80
358 3
96 000 2 000
AN 16 W 16
SAF 316 SR 19-16 LOR 84
LOR 60
EPR 10 TER 84
TER 60
67
85
31516 3316 SAF 22317 22317 CC/W33 108 000 1 900
AN 17 W 17
SAF 317 SR 20-17 LOR 109 LOR 188 EPR 11 TER 109 TER 188
71
90
418 338 SAF 22318 22318 CC/W33 124 000 1 800
AN 18 W 18
92
100
412 31316 SAF 22320 22320 CC/W33 160 000 1 700
AN 20 W 20
SAF 320 SR 24-20 LOR 118 LOR 106 EPR 12 TER 118 TER 106 107
110
478 4316 SAF 22322 22322 CC/W33 187 000 1 600
AN 22 W 22
SAF 322 SR 0-22
LOR 121 LOR 113 EPR 14 TER 121 TER 113 145
120
5516 4916 SAF 22324 22324 CC/W33 217 000 1 400
AN 24 W 24
SAF 324 SR 0-24
130
578 41516 SAF 22326 22326 CC/W33 252 000 1 300
AN 26 W 26
SAF 326 SR 0-26
140
614 5516 SAF 22328 22328 CC/W33 290 000 1 100
AN 28 W 28
SAF 328 SR 0-28
150
658 534 SAF 22330 22330 CC/W33 328 000 1 000
AN 30 W 30
160
6116 SAF 22332 22332 CC/W33 360 000
950
AN 32 W 32
170
7716 6716 SAF 22334 22334 CC/W33 396 000
950
AN 34 W 34
180
838 714 SAF 22338 22338 CC/W33 477 000
850
AN 38 W 38
200
834 758 SAF 22340 22340 CC/W33 522 000
850
AN 40 W 40
SAF 340 SR 0-40
SAF 22316 22316 CC/W33
Sizes SAF 22308 - SAF 22310, two-bolt base only; sizes SAF 22311 - SAF 22317, two-or four-bolt base options; sizes SAF 22318 - SAF 22340, four-bolt base only.
366
SAF 22300
S-3
S-2
da
R
K
F
C
How to order
SAF 22315
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF 22315
SAF 22315Y
SAF 22315TLC
SAF 22315T
SAFS 22315
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
T2
T3
in
SAF 22308
212
814
238
612
41316
1316
(2)-12
1532
312
3932
SAF 22309
234
958
234
778
738
5516
1932
414
(2)-58
1516
3916
3916
SAF 22310
1058
234
118
734
51316
138
458
(2)-58
1716
334
334
SAF 22311
314
11
318
1316
912
818
6316
1716
(2)-58, (4)-12
112
378
378
SAF 22312
314
1114
318
1316
958
858
178
638
1516
514
(2)-58, (4)-12
1916
4332
4116
SAF 22313
312
13
312
114
11
958
218
61932
11332
5516
(2)-34, (4)-58
11116
418
418
SAF 22314
334
13
312
114
11
978
218
738
11532
538
(2)-34, (4)-58
11116
4532
418
SAF 22315
1334
378
158
1158
1038
218
7916
11932
578
(2)-34, (4)-58
178
412
4916
SAF 22316
414
1414
378
1516
1258
1058
218
814
11116
612
(2)-34, (4)-58
11516
41932
41932
SAF 22317
412
1514
438
134
1318
1158
238
834
134
634
(2)-78, (4)-34
2116
41116
41932
SAF 22318
434
1512
438
1312
12
214
9316
178
678
(4)-34
2316
434
41932
SAF 22320
514
1612
434
218
1412
1314
234
10316
2132
738
(4)-34
2716
SAF 22322
1838
514
238
16
1458
314
11516
21332
818
(4)-78,
258
514
538
SAF 22324
6516
2114
614
212
1814
17
334
1212
238
838
(4)-1
21316
512
512
SAF 22326
61116
22
614
258
1914
1738
334
13516
2716
834
(4)-1
51116
51116
SAF 22328
7116
2434
634
234
2158
1938
414
14316
2916
938
(4)-1
314
6116
6116
SAF 22330
712
2634
718
2358
2078
458
1478
258
934
(4)-1
3716
614
614
SAF 22332
778
28
712
318
2438
2158
412
151116
21116
1034
(4)-114
358
61116
61116
SAF 22334
814
2912
338
25
2212
1612
234
1114
(4)-14
334
7116
678
SAF 22338
912
3234
834
334
2778
2434
514
1858
338
12
(4)-112
4116
8116
7716
SAF 22340
978
3414
2912
2614
512
1912
3716
1238
(4)-112
418
8732
71932
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
367

Spherical roller / adapter mount
SAF 22500
H
How to order
SAF 22515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 22515
SAF 22515Y
SAF 22515TLC
SAF 22515T
SAF 22515 x 212
SAFS 22515
A
D
E
B
Held and free: Standard and standard option blocks come with an enclosed stabilizing ring. For a free unit, discard the enclosed stabilizing rings.
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional*
in
Bearing
basic load
rating
dynamic
C
LER / LOR Adapter

grease
assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
1316
SAF 22507
22207 CCK/W33
17 200
6 700
SNW 7
SAF 507
36053-6
LER 14
EPR 2
TER 14
1716
138, 112
SAF 22509
22209 CCK/W33
20 200
5 300
SNW 9
SAF 509
SR 9-9
LER 17
EPR 3
TER 17
12
11116
158, 134
SAF 22510
22210 CCK/W33
21 700
5 000
SNW 10
SAF 510
SR 10-0
LER 20
EPR 4
TER 20
13
11516
178, 2
SAF 22511
22211 EK
30 100
4 500
SNW 11
SAF 511
SR 11-0
LER 24
EPR 5
TER 24
16
2316
218, 214
SAF 22513
22213 EK
43 400
3 800
SNW 13
SAF 513
SR 13-0
LER 29
EPR 6
TER 29
23
2716
238, 212
SAF 22515
22215 EK
47 700
3 400
SNW 15
SAF 515
SR 15-0
LOR 37
EPR 7
TER 37
28
21116
258, 234
SAF 22516
22216 EK
53 100
3 200
SNW 16
SAF 516
SR 16-13
LOR 44
EPR 8
TER 44
37
21516
21316, 278, 3
SAF 22517
22217 CCK/W33
55 100
3 000
SNW 17
SAF 517
SR 17-14
LOR 53
EPR 9
TER 53
38
3316
3116, 318, 314 SAF 22518
22218 CCK/W33
65 200
2 600
SNW 18
SAF 518
SR 18-15
LOR 188
EPR 11
TER 188
47
3716
3516, 338, 312 SAF 22520
22220 CCK/W33
81 000
2 200
SNW 20
SAF 520
SR 20-17
LOR 102
EPR 12
TER 102
62
31516
31316, 378, 4
SAF 22522
22222 CCK/W33
105 000
2 000
SNW 22
SAF 522
SR 22-19
LOR 109
EPR 13
TER 109
73
4316
4116, 418, 414 SAF 22524
22224 CCK/W33
121 000
1 900
SNW 24
SAF 524
SR 24-20
LOR 113
EPR 14
TER 113
104
4716
4516, 438, 412 SAF 22526
22226 CCK/W33
142 000
1 800
SNW 26
SAF 526
SR 26-0
LOR 117
EPR 15
TER 117
144
41516
41316, 478, 5
SAF 22528
22228 CCK/W33
160 000
1 700
SNW 28
SAF 528
SR 28-0
LOR 122
EPR 27
TER 122
153
5316
518, 514
SAF 22530
22230 CCK/W33
191 000
1 600
SNW 30
SAF 530
SR 30-0
LOR 125
EPR 16
TER 125
199
5716
538, 512
SAF 22532
22232 CCK/W33
225 000
1 500
SNW 32
SAF 532
SR 32-0
LOR 130
EPR 16
TER 130
212
51516
51316, 578, 6
SAF 22534
22234 CCK/W33
252 000
1 300
SNW 34
SAF 534
SR 34-0
LOR 140
EPR 18
TER 140
276
6716
6516, 638, 612 SAF 22536
22236 CCK/W33
265 000
1 300
SNW 36
SAF 536
SR 36-30
LOR 148
EPR 19
TER 148
301
61516
61316, 678, 7
SAF 22538
22238 CCK/W33
286 000
1 200
SNW 38
SAF 538
SR 38-32
LOR 155
EPR 21
TER 155
374
7316
718, 714
SAF 22540
22240 CCK/W33
328 000
1 100
SNW 40
SAF 540
SR 40-34
LOR 159
EPR 21
TER 159
443
71516
71316, 778, 8
SAF 22544
22244 CCK/W33
396 000
950
SNW 44
SAF 544
SR 44-38
LOR 167
EPR 23
TER 167
577
*Optional shaft sizes require different adapter sleeve and seals.

Sizes SAF 22507 - SAF 22513, two-bolt base only; sizes SAF 22515 - SAF 22520, two-or four-bolt base options; sizes SAF 22522 - SAF 22544, four-bolt base only.
368
SAF 22500
Fixed
X
X
S-1
S-1
Float
K
K
How to order
SAF 22515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 22515
SAF 22515Y
SAF 22515TLC
SAF 22515T
SAF 22515 x 212
SAFS 22515
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
3316
32
(2)-12
13
in
SAF 22507
712
13
618
558
334
SAF 22509
214
814
238
13
614
438
31
358
64
(2)-12
1332
3132
SAF 22510
212
814
238
15
612
434
1332
358
64
(2)-12
1532
314
SAF 22511
234
958
234
15
778
738
5132
1316
378
64
(2)-58
11364
338
SAF 22513
11
318
912
818
52132
1332
412
32
(2)-58
12564
358
SAF 22515
314
1114
318
118
958
858
178
618
118
41116
64
(2)-58, (4)-12
1716
31316
SAF 22516
312
13
312
114
11
958
218
61932
114
5516
16
(2)-34, (4)-58
11532
418
SAF 22517
334
13
312
114
11
978
218
718
138
16
(2)-34, (4)-58
1916
32932
SAF 22518
1334
378
158
1158
1038
218
7916
112
578
16
(2)-34, (4)-58
134
4116
SAF 22520
412
1514
438
134
1318
1158
238
81532
12132
618
16
(2)-78, (4)-34
15964
438
SAF 22522
41516
1612
434
1412
1258
234
91132
12532
612
16
(4)-34
218
4916
SAF 22524
514
1612
434
218
1412
1314
234
10316
12732
738
16
(4)-34
2932
SAF 22526
1838
514
238
16
1458
314
11516
21132
818
16
(4)-78
21532
5516
SAF 22528
2018
578
238
1718
16
338
1134
2132
758
16
(4)-1
22964
518
SAF 22530
6516
2114
614
212
1814
17
334
1212
838
16
(4)-1
23964
512
SAF 22532
61116
22
614
258
1914
1738
334
13516
2116
834
16
(4)-1
23132
51116
SAF 22534
7116
2434
634
234
2158
1938
414
14316
2532
958
16
(4)-1
318
6116
SAF 22536
712
2634
718
2358
2078
458
1478
238
10
16
(4)-1
3964
614
SAF 22538
778
28
712
318
2438
2158
412
151116
2716
1034
16
(4)-114
31964
61116
SAF 22540
814
2912
338
25
2212
1612
21532
1114
16
(4)-114
312
7116
SAF 22544
912
3234
834
334
2778
2434
514
1858
318
12
(4)-112
358
714
16
16
16
16
8
32
16
16
3132
369

SAF 22600
How to order
SAF 22615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 22615
SAF 22615Y
SAF 22615TLC
SAF 22615T
SAF 22615 x 2
SAFS 22615
Shaft dia.
Designations
S-1
Standard Optional*
Complete
pillow block
Bearing
in
Bearing
basic load
rating
dynamic
C
LER / LOR Adapter

grease
assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
1716
138, 112
SAF 22609
22309 EK
41 200
3 800
SNW 109
SAF 609
SR 11-9
LER 17
EPR 3
TER 17
20
11116
158, 134
SAF 22610
22310 EK
49 500
3 400
SNW 110
SAF 610
SR 0-10
LER 20
EPR 4
TER 20
24
11516
178, 2
SAF 22611
22311 EK
60 700
3 200
SNW 111
SAF 611
SR 13-11
LER 24
EPR 5
TER 24
29
2316
218, 214
SAF 22613
22313 EK
76 500
2 600
SNW 113
SAF 613
SR 16-13
LOR 32
EPR 7
TER 32
40
2716
238, 212
SAF 22615
22315 CCK/W33
90 000
2 200
SNW 115
SAF 615
SR 18-15
LOR 37
EPR 7
TER 37
52
21116
258, 234
SAF 22616
22316 CCK/W33
96 700
2 000
SNW 116
SAF 616
SR 19-16
LOR 44
EPR 8
TER 44
71
21516
21316, 278, 3 SAF 22617
22317 CCK/W33
108 000
1 900
SNW 117
SAF 617
SR 20-17
LOR 184
EPR 10
TER 184
75
3316
3116, 318, 314 SAF 22618
22318 CCK/W33
124 000
1 800
SNW 118
SAF 618
SR 21-18
LOR 188
EPR 11
TER 188
97
3716
3516, 338, 312 SAF 22620
22320 CCK/W33
160 000
1 700
SNW 120
SAF 620
SR 24-20
LOR 102
EPR 12
TER 102
113
31516
31316, 378, 4 SAF 22622
22322 CCK/W33
187 000
1 600
SNW 122
SAF 622
SR 0-22
LOR 109
EPR 13
TER 109
153
4316
4116, 418, 414 SAF 22624
22324 CCK/W33
217 000
1 400
SNW 124
SAF 624
SR 0-24
LOR 113
EPR 14
TER 113
206
4716
4516, 438, 412 SAF 22626
22326 CCK/W33
252 000
1 300
SNW 126
SAF 626
SR 0-26
LOR 117
EPR 15
TER 117
233
41516
41316, 478, 5 SAF 22628
22328 CCK/W33
290 000
1 100
SNW 128
SAF 628
SR 0-28
LOR 122
EPR 27
TER 122
296
5316
518, 514
SAF 22630
22330 CCK/W33
328 000
1 000
SNW 130
SAF 630
SR 36-30
LOR 125
EPR 16
TER 125
322
5716
538, 512
SAF 22632
22332 CCK/W33
360 000
950
SNW 132
SAF 632
SR 38-32
LOR 130
EPR 16
TER 130
401
51516
51316, 578, 6 SAF 22634
22334 CCK/W33
396 000
950
SNW 134
SAF 634
SR 40-34
LOR 140
EPR 18
TER 140
510
61516
61316, 678, 7 SAF 22638
22338 CCK/W33
477 000
850
SNW 138
SAF 638
SR 44-38
LOR 155
EPR 21
TER 155
609
7316
718, 714
22340 CCK/W33
522 000
850
SNW 140
SAF 640
SR 0-40
LOR 159
EPR 21
TER 159
902
SAF 22640

370

SAF 22600
How to order
SAF 22615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 22615
SAF 22615Y
SAF 22615TLC
SAF 22615T
SAF 22615 x 2
SAFS 22615
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
958
234
778
738
5516
1932
414
16
(2)-58
1516
338
(No. reqd)
in
SAF 22609
234
SAF 22610
1058
234
118
734
51316
138
458
16
(2)-58
1716
334
SAF 22611
314
11
318
1316
912
818
6316
1716
478
16
(2)-58, (4)-12
112
378
SAF 22613
312
13
312
114
11
958
218
61932
11332
5516
16
(2)-34, (4)-58
11116
418
SAF 22615
1334
378
158
1158
1038
218
7916
11932
578
16
(2)-34, (4)-58
178
41332
SAF 22616
414
1414
378
134
1258
1058
218
814
11116
612
16
(2)-34, (4)-58
11516
41932
SAF 22617
412
1514
438
134
1318
1158
238
834
134
634
16
(2)-78, (4)-34
2116
4916
SAF 22618
434
1512
438
1312
12
214
914
178
678
16
(4)-34
2316
4916
SAF 22620
514
1612
434
218
1412
1314
234
10316
2132
7516
16
(4)-34
2716
SAF 22622
1838
514
238
16
1458
314
11516
21332
818
16
(4)-78
258
538
SAF 22624
6516
2114
614
212
1814
17
334
1212
238
838
16
(4)-1
21316
512
SAF 22626
61116
22
614
258
1914
1738
334
13516
2716
834
16
(4)-1
51116
SAF 22628
7116
2434
634
234
2158
1938
414
14316
2916
958
16
(4)-1
314
6116
SAF 22630
712
2634
718
2358
2078
458
1478
258
934
16
(4)-1
3716
614
SAF 22632
778
28
712
318
2438
2158
412
151116
21116
1034
16
(4)-114
358
61116
SAF 22634
814
2912
338
25
2212
1612
234
1114
16
(4)-114
334
61516
SAF 22638
912
3234
834
334
2778
2434
514
1858
338
12
16
(4)-112
4116
7516
SAF 22640
978
3414
2912
2614
512
1912
3716
1238
16
(4)-112
418
71932
371

SAF 23000 KA
How to order
SAF 23024 KA x 4316
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 23024 KA x 4316

SAF 23024 KAY x 4316
SAF 23024 KA/TLC x 4316
SAF 23024 KAT x 4316
SAF 23024 KA x 414
SAFS 23024
H
A
D
E
B
Held and free: Specify the appropriate stabilizing ring for a held unit.
Shaft dia.
S-1
Standard Optional*
Designations
Complete
pillow block
Bearing
in
Bearing
basic load
rating
dynamic
C
LOR
Adapter
grease assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(2 reqd)
Triple ring End

seal
plug
(2 reqd)
Taconite
seal
lbs
4316
4116, 418, 414 SAF 23024 KA x 4316
23024 CCK/W33
78 700 2 000
SNW 3024 x 4316 SAF 024 KA x 4316
38151-24 LOR 113
EPR 14
TER 113
87
4716
4516, 438, 412 SAF 23026 KA x 4716
23026 CCK/W33
105 000 1 900
SNW 3026 x 4716 SAF 026 KA x 4716
38151-26 LOR 117
EPR 15
TER 117
71
41516
41316, 478, 5 SAF 23028 KA x 41516 23028 CCK/W33
105 000 1 800
SNW 3028 x 41516 SAF 028 KA x 41516 36053-50 LOR 122
EPR 27
TER 122 138
5316
518, 514
SAF 23030 KA x 5316
23030 CCK/W33
115 000 1 700
SNW 3030 x 5316 SAF 030 KA x 5316
SR-0-21
LOR 125
EPR 16
TER 125 149
5716
538, 512
SAF 23032 KA x 5716
23032 CCK/W33
132 000 1 700
SNW 3032 x 5716 SAF 032 KA x 5716
38151-32 LOR 130
EPR 16
TER 130 175
51516
51316, 578, 6 SAF 23034 KA x 51516 23034 CCK/W33
160 000 1 600
SNW 3034 x 51516 SAF 034 KA x 51516 SR-0-24
LOR 140
EPR 18
TER 140 220
6716
6516, 638, 612 SAF 23036 KA x 6716
23036 CCK/W33
187 000 1 400
SNW 3036 x 6716 SAF 036 KA x 6716
38151-36 LOR 148
EPR 19
TER 148 272
61516
61316, 678, 7 SAF 23038 KA x 61516 23038 CCK/W33
195 000 1 300
SNW 3038 x 61516 SAF 038 KA x 61516 38151-38 LOR 155
EPR 21
TER 155 284
7316
718, 714
23040 CCK/W33
225 000 1 200
SNW 3040 x 7316 SAF 040 KA x 7316
38151-40 LOR 159
EPR 21
TER 159 367
71516
71316, 778, 8 SAF 23044 KA x 71516 23044 CCK/W33
274 000 1 100
SNW 3044 x 71516 SAF 044 KA x 71516 36053-140 LOR 167
EPR 23
TER 167 386
81516
8716, 812, 9
SAF 23048 KA x 81516 23048 CCK/W33
290 000 1 000
SNP 3048 x 81516 SAF 048 KA x 81516 A-8897
LOR 552
X-5217-4 TER 552 474
9716
912
SAF 23052 KA x 9716
360 000
900
SNP 3052 x 9716 SAF 052 KA x 9716
A-8898
LOR 553
X-5217-2 TER 553 530
91516
10
SAF 23056 KA x 91516 23056 CACK/W33 342 000
850
SNP 3056 x 91516 SAF 056 KA x 91516 A-8819
LOR 607
X-5217-2 TER 607 800
10716
1012
SAF 23056 KA x 10716 23056 CACK/W33 342 000
850
SNP 3056 x 10716 SAF 056 KA x 10716 A-8819
LOR 606
X-5217-1 TER 606 800
SAF 23040 KA x 7316
23052 CCK/W33

Size SAF 23024 KA, two-or four-bolt base options;
Sizes SAF 23026 KA - SAF 23056 KA, four-bolt base only.
372
SAF 23000 KA
Fixed
X
X
S-1
S-1
Float
K
K
How to order
SAF 23000 KA x 4316
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF 23024 KA x 4316

SAF 23024 KAY x 4316
SAF 23024 KA/TLC x 4316
SAF 23024 KAT x 4316
SAF 23024 KA x 414
SAFS 23024 KA x 4316
Held and free: Specify the appropriate stabilizing ring for a held unit.
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
in
SAF 23024 KA x 43/16
41/2
151/4
43/8
13/4
131/8
115/8
23/8
815/32
19/16
61/8
(2)-7/8, (4)-3/4
129/32
41/2
SAF 23026 KA x 47/16
415/16
161/2
43/4
141/2
125/8
23/4
911/32
111/16
61/2
(4)-3/4
23/32
45/8
SAF 23028 KA x 415/16
51/4
161/2
43/4
21/8
141/2
131/4
23/4
103/16
113/16
73/8
(4)-3/4
25/32
51/32
SAF 23030 KA x 53/16
183/8
51/4
23/8
16
145/8
31/4
115/16
27/32
81/8
(4)-7/8
29/32
513/32
SAF 23032 KA x 57/16
183/8
51/4
23/8
16
145/8
31/4
115/16
21/32
81/8
(4)-7/8
27/16
515/32
SAF 23034 KA x 515/16
201/8
57/8
23/8
171/8
16
33/8
113/4
123/32
75/8
(4)-1
219/32
55/32
SAF 23036 KA x 67/16
611/16
22
61/4
25/8
191/4
173/8
33/4
135/16
21/16
83/4
(4)-1
225/32
523/32
SAF 23038 KA x 615/16
611/16
22
61/4
25/8
191/4
173/8
33/4
135/16
17/8
83/4
(4)-1
213/16
523/32
SAF 23040 KA x 73/16
71/16
243/4
63/4
23/4
215/8
193/8
41/4
143/16
115/16
95/8
(4)-1
31/32
69/32
SAF 23044 KA x 715/16
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
21/4
103/4
(4)-11/4
37/32
623/32
SAF 23048 KA x 815/16
81/4
291/2
33/8
25
221/2
161/2
27/32
111/4
(4)-11/4
39/16
711/16
SAF 23052 KA x 97/16
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
23/4
12
(4)-11/2
37/8
81/16
SAF 23056 KA x 915/16
97/8
341/4
291/2
261/4
51/2
191/2
27/8
123/8
(4)-11/2
81/4
SAF 23056 KA x 107/16
97/8
341/4
291/2
261/4
51/2
191/2
27/8
123/8
(4)-11/2
81/4
373

Toroidal roller (CARB) / cylindrical mount
SAF C2200
Toroidal/ C2200 series bearing
Free bearing only
H
How to order
SAF C2215
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF C2215
SAF C2215Y
SAF C2215TLC
SAF C2215T
SAFS C2215
A
D
E
B
Held: Standard and standard option blocks come with a stabilizing ring. For toroidal bearings, the enclosed stabilizing ring must be used.
Shaft
Designations
dia.
Complete
pillow block
da
S-2 S-3
mm
in
Bearing
Bearing
basic load
rating
dynamic
C
LOR
Lockgrease nut*
speed
limit
lbs
r/min
Lockwasher
Pillow
block
housing
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
65
31/16 27/16 SAF C2213 C2213TN9
35 000
3 800 KMFE 13
SAF 213 SR 13-0
LOR 55
LOR 37
EPR 7
TER 55
TER 37
22
75
37/16 213/16 SAF C2215 C2215
39 000
3 400 KMFE 15
SAF 215 SR 15-0
LOR 79
LOR 46
EPR 8
TER 79
TER 46
27
80
35/8 3
SAF C2216 C2216
43 000
3 200 KMFE 16
SAF 216 SR 16-13 LOR 82
LOR 54
EPR 9
TER 82
TER 54
34
85
315/16 33/16 SAF C2217 C2217
53 800
3 000 KMFE 17
SAF 217 SR 17-14 LOR 89
LOR 63
EPR 9
TER 89
TER 63
35
90
41/18 33/8 SAF C2218 C2218
63 500
2 600 KMFE 18
SAF 218 SR 18-15 LOR 112
44
100
41/2 313/16 SAF C2220 C2220
80 300
2 200 KMFE 20
SAF 220 SR 20-17 LOR 118
65
110
47/8 43/16 SAF C2222 C2222
103 500
2 000 KMFE 22
SAF 222 SR 22-19 LOR 121
88
130
57/8 415/16 SAF C2226 C2226
144 000
1 800 KML 26
MBL 26 SAF 226 SR 26-0
LOR 136
134
140
61/4 55/16 SAF C2228 C2228
163 000
1 700 KML 28
MBL 28 SAF 228 SR 28-0
LOR 144
141
150
65/8 53/4 SAF C2230 C2230
190 000
1 600 KML 30
MBL 30 SAF 230 SR 30-0
LOR 151
181
170
77/16 67/16 SAF C2234 C2234
245 000
1 300 KML 34
MBL 34 SAF 234 SR 34-0
LOR 161
263
190
83/8 71/4 SAF C2238 C2238
270 000
1 200 KML 38
MBL 38 SAF 238 SR 38-32 LOR 171
356
220
99/16 85/16 SAF C2244 C2244
389 000
950 KML 44
MBL 44 SAF 244 SR 44-38 LOR 179
535
Size SAF C2213, two-bolt base only;

Sizes SAF C2215 - SAF C2220, two-or four-bolt base options;
Sizes SAF C2222 - SAF C2224, four-bolt base only.
* Refer to page 452 for information on KMFE and KML lock nuts.
374
T3
T2
SAF C2200
Toroidal / C2200 series bearing
Free bearing only
Fixed
X
S-3
S-2
S-2 da
S-3
Float
K
K
How to order
SAF C2215
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF C2215
SAF C2215Y
SAF C2215TLC
SAF C2215T
SAFS C2215
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
T2
T3
in
SAF C2213
11
31/8
91/2
81/8
521/32
41/2
/16
(2)-5/8
11/4
33/4
33/4
SAF C2215
31/4
111/4
31/8
11/8
95/8
85/8
17/8
61/8
411/16
/16
(2)-5/8, (4)-1/2
19/32
37/8
37/8
SAF C2216
31/2
13
31/2
11/4
11
95/8
21/8
619/32
11/4
55/16
/16
(2)-3/4, (4)-5/8
115/32
41/8
43/32
SAF C2217
33/4
13
31/2
11/4
11
97/8
21/8
71/8
13/8
/16
(2)-3/4, (4)-5/8
19/16
329/32
329/32
SAF C2218
133/4
37/8
15/8
115/8
103/8
21/8
79/16
11/2
57/8
/16
(2)-3/4, (4)-5/8
13/4
43/16
43/32
SAF C2220
41/2
151/4
43/8
13/4
131/8
115/8
23/8
815/32
121/32
61/8
/16
(2)-7/8, (4)-3/4
159/64
45/16
45/16
SAF C2222
415/16
161/2
43/4
141/2
125/8
23/4
911/32
125/32
61/2
/16
(4)-3/4
21/8
41/2
49/16
SAF C2226
183/8
51/4
23/8
16
145/8
31/4
115/16
211/32
81/8
/16
(4)-7/8
215/32
51/4
55/16
SAF C2228
201/8
57/8
23/8
171/8
16
33/8
113/4
21/32
75/8
/16
(4)-1
239/64
51/8
51/8
SAF C2230
65/16
211/4
61/4
21/2
181/4
17
33/4
121/2
83/8
/16
(4)-1
249/64
51/2
51/2
SAF C2234
71/16
243/4
63/4
23/4
215/8
193/8
41/4
143/16
25/32
95/8
/16
(4)-1
31/8
63/16
SAF C2238
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
27/16
103/4
/16
(4)-11/4
319/64
77/16
613/16
SAF C2244
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
31/8
12
(4)-11/2
35/8
81/16
/16
375

SAF C2300
Free bearing only
How to order
SAF C2315
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF C2315
SAF C2315Y
SAF C2315TLC
SAF C2315T
SAFS C2315
Free: Standard and standard option blocks come with a stabilizing ring. For toroidal bearings, the enclosed stabilizing ring must be used.
Shaft
Designations
dia.
Complete
pillow block
da
S-2
mm
in
Bearing
S-3
Bearing
basic load
rating
dynamic
C
LOR
grease
speed
limit
lbs
r/min
Locknut
Lock- Pillow
washer block
housing
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
70
31/4 25/8
SAF C2314
C2314
79 000
2 400
N 14
W 14
SAF 314 SR 17-14 LOR 64
LOR 43
EPR 8
TER 64
TER 43
42
75
37/16 213/16
SAF C2315
C2315
84 000
2 200
AN 15 W 15
SAF 315 SR 18-15 LOR 79
LOR 46
EPR 8
TER 79
TER 46
48
80
35/8 3
SAF C2316
C2316
98 300
2 000
AN 16 W 16
SAF 316 SR 19-16 LOR 84
LOR 60
EPR 10 TER 84
TER 60
67
85
315/16 33/16
SAF C2317
C2317
105 000
1 900
AN 17 W 17
71
90
41/8 33/8
SAF C2318
C2318
120 000
1 800
AN 18 W 18
92
41/2 313/16
SAF C2320
C2320
158 000
1 700
AN 20 W 20
100

376
SAF C2300
Free bearing only
Held
Held
S-2
da
S-3
Free
Free
K
F
C
How to order
SAF C2315
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Cast-steel
FSAF C2315
SAF C2315Y
SAF C2315TLC
SAF C2315T
SAFS C2315

Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
97/8
21/8
73/8
115/32
53/8
(2)-3/4, (4)-5/8
111/16
45/32
41/8
(No. reqd)
T2
T3
in
SAF C2314
33/4
13
31/2
11/4
11
SAF C2315
133/4
37/8
15/8
115/8
103/8
21/8
79/16
119/32
57/8
(2)-3/4, (4)-5/8
17/8
41/2
49/16
SAF C2316
41/4
141/4
37/8
15/16
125/8
105/8
21/8
81/4
111/16
61/2
(2)-3/4, (4)-5/8
115/16
419/32
419/32
SAF C2317
41/2
151/4
43/8
13/4
131/8
115/8
23/8
83/4
13/4
63/4
(2)-7/8, (4)-3/4
21/16
411/16
419/32
SAF C2318
43/4
151/2
43/8
131/2
12
21/4
93/16
17/8
67/8
(4)-3/4
23/16
43/4
419/32
SAF C2320
51/4
161/2
43/4
21/8
141/2
131/4
23/4
103/16
21/32
73/8
(4)-3/4
27/16
/16
/16
/16
/16
/16
/16
377

Toroidal roller (CARB) / adapter mount
SAF C2500
Toroidal / C2200 K series bearing
Free bearing only
H
How to order
SAF C2515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF C2515
SAF C2515Y
SAF C2515TLC
SAF C2515T
SAF C2515 x 212
SAFS C2515
A
D
E
B
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional*
in
Bearing
basic load
rating
dynamic
C
LER / LOR Adapter

grease
assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
13/16
SAF C2507
C2207 KTN9
16 000
6 700
HA 307E
SAF 507
36053-6
LER 14
EPR 2
TER 14
17/16
13/8, 11/2
SAF C2509
C2209 KTN9
18 400
5 300
HA 309E
SAF 509
SR 9-9
LER 17
EPR 3
TER 17
12
111/16
15/8, 13/4
SAF C2510
C2210 KTN9
19 000
5 000
HA 310E
SAF 510
SR 10-0
LER 20
EPR 4
TER 20
13
115/16
17/8, 2
SAF C2511
C2211 KTN9
22 700
4 500
HA 311E
SAF 511
SR 11-0
LER 24
EPR 5
TER 24
16
23/16
21/8, 21/4
SAF C2513
C2213 KTN9
35 500
3 800
HA 313E
SAF 513
SR 13-0
LER 29
EPR 6
TER 29
22
27/16
23/8, 21/2
SAF C2515
C2215 K
39 000
3 400
HA 315E
SAF 515
SR 15-0
LOR 37
EPR 7
TER 37
28
211/16
25/8, 23/4
SAF C2516
C2216 K
43 000
3 200
HA 316E
SAF 516
SR 16-13
LOR 44
EPR 8
TER 44
37
215/16
213/16, 27/8, 3
SAF C2517
C2217 K
53 800
3 000
HA 317E
SAF 517
SR 17-14
LOR 53
EPR 9
TER 53
38
33/16
31/16, 31/8, 31/4 SAF C2518
C2218 K
65 500
2 600
HA 318E
SAF 518
SR 18-15
LOR 188
EPR 11
TER 188
47
37/16
35/16, 33/8, 31/2 SAF C2520
C2220 K
80 300
2 200
HA 320E
SAF 520
SR 20-17
LOR 102
EPR 12
TER 102
62
315/16
313/16, 37/8, 4
SAF C2522
C2222 K
103 500
2 000
HA 322E
SAF 522
SR 22-19
LOR 109
EPR 13
TER 109
73
47/16
45/16, 43/8, 41/2 SAF C2526
C2226 K
144 000
1 800
HA 3126L SAF 526
SR 26-0
LOR 117
EPR 15
TER 117
144
415/16
413/16, 47/8, 5
SAF C2528
C2228 K
163 000
1 700
HA 3128L SAF 528
SR 28-0
LOR 122
EPR 27
TER 122
153
53/16
51/8, 51/4
SAF C2530
C2230 K
190 000
1 600
HA 3130L SAF 530
SR 30-0
LOR 125
EPR 16
TER 125
199
515/16
513/16, 57/8, 6
SAF C2534
C2234 K
245 000
1 300
HA 3134L SAF 534
SR 34-0
LOR 140
EPR 18
TER 140
276
615/16
613/16, 67/8, 7
SAF C2538
C2238 K
270 000
1 200
HA 3138L SAF 538
SR 38-32
LOR 155
EPR 20
TER 155
374
715/16
713/16, 77/8, 8
SAF C2544
C2244 K
389 000
950
HA 3144L SAF 544
SR 44-38
LOR 167
EPR 23
TER 167
576

Sizes SAF C2507 - SAF C2513, two-bolt base only;
378
SAF C2500
Free bearing only
Fixed
X
X
S-1
S-1
Float
K
K
How to order
SAF C2515
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF C2515
SAF C2515Y
SAF C2515TLC
SAF C2515T
SAF C2515 x 212
SAFS C2515
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
33/16
/32
(2)-1/2
13
in
SAF C2507
71/2
13
61/8
55/8
33/4
SAF C2509
21/4
81/4
23/8
13
61/4
43/8
31
35/8
/64
(2)-1/2
13/32
31/32
SAF C2510
21/2
81/4
23/8
15
61/2
43/4
13/32
35/8
/64
(2)-1/2
15/32
31/4
SAF C2511
23/4
95/8
23/4
15
77/8
73/8
51/32
13/16
37/8
/64
(2)-5/8
113/64
33/8
SAF C2513
11
31/8
91/2
81/8
521/32
13/32
41/2
/32
(2)-5/8
125/64
35/8
SAF C2515
31/4
111/4
31/8
11/8
95/8
85/8
17/8
61/8
11/8
411/16
/64
(2)-5/8, (4)-1/2
17/16
313/16
SAF C2516
31/2
13
31/2
11/4
11
95/8
21/8
619/32
11/4
55/16
/16
(2)-3/4, (4)-5/8
115/32
41/8
SAF C2517
33/4
13
31/2
11/4
11
97/8
21/8
71/8
13/8
/16
(2)-3/4, (4)-5/8
19/16
329/32
SAF C2518
133/4
37/8
15/8
115/8
103/8
21/8
79/16
11/2
57/8
/16
(2)-3/4, (4)-5/8
13/4
41/16
SAF C2520
41/2
151/4
43/8
13/4
131/8
115/8
23/8
815/32
121/32
61/8
/16
(2)-7/8, (4)-3/4
159/64
43/8
SAF C2522
415/16
161/2
43/4
141/2
125/8
23/4
911/32
125/32
61/2
/16
(4)-3/4
21/8
49/16
SAF C2526
183/8
51/4
23/8
16
145/8
31/4
115/16
211/32
81/8
/16
(4)-7/8
215/32
55/16
SAF C2528
201/8
57/8
23/8
171/8
16
33/8
113/4
21/32
75/8
/16
(4)-1
229/64
51/8
SAF C2530
65/16
211/4
61/4
21/2
181/4
17
33/4
121/2
83/8
/16
(4)-1
239/64
51/2
SAF C2534
71/16
243/4
63/4
23/4
215/8
193/8
41/4
143/16
25/32
95/8
/16
(4)-1
31/8
61/16
SAF C2538
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
27/16
103/4
/16
(4)-11/4
319/64
611/16
SAF C2544
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
31/8
12
(4)-11/2
35/8
71/4
/16
/16
/16
/16
/8
/32
/16
/16
31/32
379

SAF C2600
Free bearing only
How to order
SAF C2615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF C2615
SAF C2615Y
SAF C2615TLC
SAF C2615T
SAF C2615 x 2
SAFS C2615
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional*
in
Bearing
basic load
rating
dynamic
C
LOR
grease
speed
limit
lbs
r/min
Adapter
assembly
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
27/16
23/8, 21/2
SAF C2615
C2315 K
84 000
2 200
HA 2315
SAF 615
SR 18-15
LOR 37
EPR 7
TER 37
52
211/16
25/8, 23/4
SAF C2616
C2316 K
98 300
2 000
HA 2316
SAF 616
SR 19-16
LOR 44
EPR 8
TER 44
71
215/16
213/16, 27/8, 3
SAF C2617
C2317 K
105 000
1 900
HA 2317
SAF 617
SR 20-17
LOR 184
EPR 10
TER 184
75
33/16
31/16, 31/8, 31/4
SAF C2618
C2318 K
120 000
1 800
HA 2318
SAF 618
SR 21-18
LOR 188
EPR 11
TER 188
97
37/16
35/16, 33/8, 31/2
SAF C2620
C2320 K
158 000
1 700
HA 2320
SAF 620
SR 24-20
LOR 102
EPR 12
TER 102
113

380

SAF C2600
Free bearing only
How to order
SAF C2615
Option
Specify
Four-bolt base
One end closed
PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
FSAF C2615
SAF C2615Y
SAF C2615TLC
SAF C2615T
SAF C2615 x 2
SAFS C2615
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
in
SAF C2615
133/4
37/8
15/8
115/8
103/8
21/8
79/16
119/32
57/8
(2)-3/4, (4)-5/8
17/8
411/32
SAF C2616
41/4
141/4
37/8
13/4
125/8
105/8
21/8
81/4
111/16
61/2
(2)-3/4, (4)-5/8
115/16
419/32
SAF C2617
41/2
151/4
43/8
13/4
131/8
115/8
23/8
83/4
13/4
63/4
(2)-7/8, (4)-3/4
21/16
49/16
SAF C2618
43/4
151/2
43/8
131/2
12
21/4
91/4
17/8
67/8
(4)-3/4
23/16
49/16
SAF C2620
51/4
161/2
43/4
21/8
141/2
131/4
23/4
103/16
21/32
75/16
(4)-3/4
27/16
/16
/16
/16
/16
/16
381

SAF C3000 KA
Free bearing only
H
How to order
C3036 KA x 67/16
Option
Specify
One end closed

PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
SAF C3036 KAY x 6716

SAF C3036TLC x 6716
SAF C3036 KAT x 6716
SAF C3036 KA x 612
SAFS C3036 KA x 6716
A
D
E
B
For toroidal bearings in this series, you must order the appropriate stabilizing rings.
Shaft dia.
S-1
Standard Optional*
Designations
Complete
pillow block
Bearing
in
Bearing
basic load
rating
dynamic
C
LOR
Adapter
grease assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(2 reqd)
Triple ring End

seal
plug
(2 reqd)
Taconite
seal
lbs
67/16
65/16, 63/8, 61/2 SAF C3036 KA x 67/16
C3036 K
123 500
1 400
HA 3036
SAF 036 KA x 67/16
38151-36 LOR 148
EPR 19
TER 148 272
615/16
613/16, 67/8, 7
SAF C3038 KA x 615/16
C3038 K
180 000
1 300
HA 3038
SAF 038 KA x 615/16
38151-38 LOR 155
EPR 20
TER 155 284
73/16
71/8, 71/4
SAF C3040 KA x 73/16
C3040 K
220 000
1 200
HA 3040
SAF 040 KA x 73/16
38151-40 LOR 159
EPR 21
TER 159 367
715/16
713/16, 77/8, 8
SAF C3044 KA x 715/16
C3044 K
259 000
1 100
HA 3044
SAF 044 KA x 715/16
36053-140 LOR 167
EPR 23
TER 167 386
815/16
87/16, 81/2, 9
SAF C3048 KA x 815/16
C3048 K
270 000
1 000
HA 3048
SAF 048 KA x 815/16
A-8897
LOR 552
X-5217-4 TER 552 474
97/16
91/2
SAF C3052 KA x 97/16
C3052 K
346 500
900
HA 3052
SAF 052 KA x 97/16
A-8898
LOR 553
X-5217-2 TER 553 530
915/16
10
SAF C3056 KA x 915/16
C3056 K
362 000
850
HA 3056/252.4 SAF 056 KA x 915/16
A-8819
LOR 607
X-5217-2 TER 607 800
101/2
SAF C3056 KA x 107/16
C3056 K
362 000
850
HA 3056/265.1 SAF 056 KA x 107/16
A-8819
LOR 606
X-5217-1 TER 606 800
107/16

Sizes SAF C3036 KA - SAF C3056 KA, four-bolt base only.
382
Toroidal roller / adapter mount
SAF C3000 KA
Free bearing only
Fixed
X
X
S-1
S-1
Float
K
K
How to order
SAF C3036 KA x 67/16
Option
Specify
One end closed

PosiTrac Plus seal
Taconite seals
Optional shaft size
Cast-steel
SAF C3036 KAY 6716

SAF C3036 KA/TLC x 6716
SAF C3036 KAT 6716
SAF C3036 KA x 612
SAFS C3036 KA x 6716
For toroidal bearings in this series, you must order the appropriate stabilizing rings.
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
in
SAF C3036 KA x 67/16
611/16
22
61/4
25/8
191/4
173/8
33/4
135/16
21/16
83/4
(4)-1
225/32
523/32
SAF C3038 KA x 615/16
611/16
22
61/4
25/8
191/4
173/8
33/4
135/16
17/8
83/4
(4)-1
213/16
523/32
SAF C3040 KA x 73/16
71/16
243/4
63/4
23/4
215/8
193/8
41/4
143/16
115/16
95/8
(4)-1
31/32
69/32
SAF C3044 KA x 715/16
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
21/4
103/4
(4)-11/4
37/32
623/32
SAF C3048 KA x 815/16
81/4
291/2
33/8
25
221/2
161/2
27/32
111/4
(4)-11/4
39/16
711/16
SAF C3052 KA x 97/16
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
23/4
12
(4)-11/2
37/8
81/16
SAF C3056 KA x 915/16
97/8
341/4
23/4
291/2
261/4
51/2
203/16
27/8
121/4
(4)-11/2
81/4
SAF C3056 KA x 107/16
97/8
341/4
23/4
291/2
261/4
51/2
203/16
27/8
121/4
(4)-11/2
81/4
383

SDAF 22200
Two-piece heavy duty cast-iron housing
LOR / LER triple ring seals
How to order
SDAF 22220
Option
Specify
One end closed

Taconite seals
Cast-steel
SDAF 22220Y
SDAF 22220T
SDAFS 22220
Shaft
Designations
dia.
da
Complete
pillow block
Bearing
S-2 S-3
mm in
100 41/2 313/16 SDAF 22220
LER / LOR Lock- Lock- Pillow

grease nut
washer block
speed
housing
limit
lbs
r/min
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
81 000
2 200 AN 20 W 20
SDAF 220
110 47/8 43/16 SDAFS 22222* 22222 CC/W33 105 000
2 000 AN 22 W 22
SDAFS 222 SR 22-19 LOR 121
LOR 113 EPR 14 TER 121 TER 113 102
120 55/16 49/16 SDAF 22224
22224 CC/W33 121 000
1 900 AN 24 W 24
SDAF 224
SR 24-20 LOR 127
LOR 119 EPR 15 TER 127 TER 119 118
130 57/8 415/16 SDAF 22226
22226 CC/W33 142 000
1 800 AN 26 W 26
SDAF 226
SR 26-0
LOR 136
LOR 122 EPR 27 TER 136 TER 122 169
140 61/4 55/16 SDAFS 22228* 22228 CC/W33 160 000
1 700 AN 28 W 28
SDAFS 228 SR 28-0
LOR 144
LOR 127
150 65/8 53/4 SDAF 22230
22230 CC/W33 191 000
1 600 AN 30 W 30
SDAF 230
SR 30-0
LOR 151
LOR 134 EPR 17 TER 151 TER 134 200
61/16 SDAF 22232
22232 CC/W33 225 000
1 500 AN 32 W 32
SDAF 232
SR 32-0
LOR 156
LOR 142 EPR 18 TER 156 TER 142 264
180 713/16 67/8 SDAF 22236
22236 CC/W33 265 000
1 300 AN 36 W 36
SDAF 236
SR 36-30 LOR 165
LOR 154 EPR 20 TER 165 TER 154 436
190 83/8 71/4 SDAF 22238
22238 CC/W33 286 000
1 200 AN 38 W 38
SDAF 238
SR 38-32 LER 240
LER 229
EPR 22 TER 240 TER 229 510
200 83/4 75/8 SDAF 22240
22240 CC/W33 328 000
1 100 AN 40 W 40
SDAF 240
SR 40-34 LER 244
LER 233
EPR 23 TER 244 TER 233 389
220 99/16 85/16 SDAF 22244
22244 CC/W33 396 000
SDAF 244
SR 44-38 LER 248
LER 239
EPR 25 TER 248 TER 239 787
160 7
22220 CC/W33
Bearing
basic load
rating
dynamic
C
*Available in steel only
384
950
N 44 W 44
SR 20-17 LER 205
LER 87
EPR 12 TER 205 TER 87
80
TER 144 TER 127 175

SDAF 22200
How to order
SDAF 22220
Option
Specify
One end closed

Taconite seals
Cast-steel
SDAF 22220Y
SDAF 22220T
SDAFS 22220

Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
T2
T3
in
SDAF 22220
41/2
151/4
17/8
131/8
115/8
33/8
815/16
121/32
63/4
/16
(4)-3/4
159/64
411/16
411/16
SDAFS 22222
415/16
161/2
63/4
21/8
141/2
125/8
97/8
113/16
71/4
/16
(4)-7/8
21/8
47/8
47/8
SDAF 22224
51/4
161/2
67/8
21/4
141/2
131/4
41/8
101/2
127/32
73/8
/16
(4)-7/8
29/32
415/16
415/16
SDAF 22226
183/8
71/2
23/8
16
145/8
41/2
117/8
211/32
/16
(4)-1
215/32
51/4
51/4
SDAFS 22228
201/8
71/2
23/8
171/8
16
41/2
121/16
21/8
73/16
/16
(4)-1
SDAF 22230
65/16
211/4
77/8
21/2
181/4
17
43/4
129/16
21/32
83/8
/16
(4)-11/8
249/64
57/16
57/16
SDAF 22232
611/16
22
81/4
21/2
191/4
173/8
137/16
23/32
83/4
/16
(4)-11/8
231/32
55/8
55/8
SDAF 22236
71/2
263/4
93/8
23/4
235/8
207/8
57/8
153/16
23/8
10
/16
(4)-11/4
39/64
61/8
61/8
SDAF 22238
77/8
275/8
10
231/2
211/2
61/4
16
27/16
105/8
/16
(4)-13/8
319/64
71/4
71/4
SDAF 22240
81/4
283/4
101/2
31/4
25
23
63/4
167/8
21/2
111/8
/16
(4)-13/8
31/2
71/2
71/2
SDAF 22244
91/2
32
111/4
31/2
277/8
255/8
71/4
19
31/8
117/8
/16
(4)-11/2
35/8
77/8
77/8
385

SDAF 22300
How to order
SDAF 22320
Option
Specify
One end closed

Taconite seals
Cast-steel
SDAF 22320Y
SDAF 22320T
SDAFS 22320
Shaft
Designations
dia.
Complete
pillow block
da
S-2 S-3
mm
in
Bearing
Bearing
basic load
rating
dynamic
C
LER / LOR Lock- LockPillow

grease nut
washer block
speed
housing
limit
lbs
r/min
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
85
315/16 33/16 SDAF 22317 22317 CC/W33 108 000
1 900
AN 17 W 17
SDAF 317 SR 20-17 LER 93
LER 69
EPR 11 TER 93
TER 69
83
100
41/2 313/16 SDAF 22320 22320 CC/W33 160 000
1 700
AN 20 W 20
SDAF 320 SR 24-20 LER 205
LER 87
141
110
47/8 43/16 SDAF 22322 22322 CC/W33 187 000
1 600
AN 22 W 22
SDAF 322 SR 0-22
LOR 121
LOR 113 EPR 14 TER 121 TER 113 172
120
55/16 49/16 SDAF 22324 22324 CC/W33 217 000
1 400
AN 24 W 24
SDAF 324 SR 0-24
LOR 127
LOR 119 EPR 15 TER 127 TER 119 304
130
57/8 415/16 SDAF 22326 22326 CC/W33 252 000
1 300
AN 26 W 26
SDAF 326 SR 0-26
LOR 136
LOR 122 EPR 27 TER 136 TER 122 330
140
61/4 55/16 SDAF 22328 22328 CC/W33 290 000
1 100
AN 28 W 28
SDAF 328 SR 0 28
LOR 144
LOR 127 EPR 16 TER 144 TER 127 331
150
65/8 53/4 SDAF 22330 22330 CC/W33 328 000
1 000
AN 30 W 30
SDAF 330 SR 36-30 LOR 151
LOR 134 EPR 17 TER 151 TER 134 466
160
61/16 SDAF 22332 22332 CC/W33 360 000
950
AN 32 W 32
SDAF 332 SR 38-32 LER 225
LER 217
EPR 19 TER 225 TER 217 537
170
77/16 67/16 SDAF 22334 22334 CC/W33 396 000
950
AN 34 W 34
SDAF 334 SR 40-34 LER 230
LER 220
EPR 26 TER 230 TER 220 554
180
713/16 67/8 SDAF 22336 22336 CC/W33 450 000
900
AN 36 W 36
SDAF 336 SR 0-36
LER 234
LER 223
EPR 21 TER 234 TER 223 623
190
83/8 71/4 SDAF 22338 22338 CC/W33 477 000
850
AN 38 W 38
SDAF 338 SR 44-38 LER 240
LER 229
EPR 22 TER 240 TER 229 734
386

SDAF 22300
How to order
SDAF 22320
Option
Specify
One end closed

Taconite seals
Cast-steel
SDAF 22320Y
SDAF 22320T
SDAFS 22320

Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
815/16
125/32
63/4
/16
(4)-3/4
21/16
43/4
43/4
/16
(4)-7/8
27/16
(No. reqd)
T2
T3
in
SDAF 22317
41/2
151/4
17/8
131/8
115/8
33/8
SDAF 22320
51/4
161/2
67/8
21/4
141/2
131/4
41/8
101/2
21/32
73/8
SDAF 22322
183/8
71/2
23/8
16
145/8
41/2
117/8
213/32
/16
(4)-1
25/8
51/4
51/4
SDAF 22324
65/16
211/4
77/8
21/2
181/4
17
43/4
129/16
213/32
83/8
/16
(4)-11/8
213/16
57/16
57/16
SDAF 22326
611/16
22
81/4
21/2
191/4
173/8
137/16
215/32
83/4
/16
(4)-11/8
55/8
55/8
SDAF 22328
71/16
243/4
21/2
215/8
193/8
51/2
141/4
29/16
93/8
/16
(4)-11/4
31/4
61/16
61/16
SDAF 22330
71/2
263/4
93/8
23/4
235/8
207/8
57/8
153/16
25/8
93/4
/16
(4)-11/4
37/16
61/8
61/8
SDAF 22332
77/8
275/8
10
231/2
211/2
61/4
16
223/32
105/8
/16
(4)-13/8
35/8
61/2
61/2
SDAF 22334
81/4
283/4
101/2
31/4
25
23
63/4
167/8
23/4
111/8
/16
(4)-13/8
33/4
67/8
67/8
SDAF 22336
87/8
301/2
103/4
31/4
263/8
241/8
67/8
1715/16
31/16
113/8
/16
(4)-11/2
37/8
67/8
67/8
SDAF 22338
91/2
32
111/4
31/2
277/8
255/8
71/4
19
313/32
117/8
/16
(4)-11/2
41/16
77/8
77/8
387

SDAF 22500
How to order
SDAF 22520
Option
Specify
One end closed

Taconite seals
Cast-Steel
Optional shaft size
SDAF 22520Y
SDAF 22520T
SDAFS 22520
SDAF 22520 x 312
Held and free: Standard and standard option blocks come with an enclosed stabilizing ring. For a free unit, discard the enclosed stabilizing
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional
in
37/16
35/16, 33/8, 31/2 SDAF 22520
315/16
313/16, 37/8, 4
43/16
41/16, 41/8, 41/4 SDAF 22524
47/16
45/16, 43/8, 41/2 SDAF 22526
415/16
Bearing
basic load
rating
dynamic
C
LER / LOR Adapter

grease
assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
22220 CCK/W33
81 000
2 200
SNW 20
SDAF 520
SR 20-17
LER 75
EPR 11
TER 75
96
SDAFS 22522* 22222 CCK/W33
105 000
2 000
SNW 22
SDAFS 522 SR 22-19
LER 93
EPR 13
TER 93
105
22224 CCK/W33
121 000
1 900
SNW 24
SDAF 524
SR 24-20
LOR 113
EPR 14
TER 113
125
22226 CCK/W33
142 000
1 800
SNW 26
SDAF 526
SR 26-0
LOR 117
EPR 15
TER 117
199
413/16, 47/8, 5
SDAFS 22528* 22228 CCK/W33
160 000
1 700
SNW 28
SDAFS 528 SR 28-0
LOR 122
EPR 27
TER 122
220
53/16
51/8, 51/4
SDAF 22530
22230 CCK/W33
191 000
1 600
SNW 30
SDAF 530
SR 30-0
LOR 125
EPR 16
TER 125
259
57/16
53/8, 51/2
SDAF 22532
22232 CCK/W33
225 000
1 500
SNW 32
SDAF 532
SR 32-0
LOR 130
EPR 16
TER 130
330
67/16
65/16, 63/8, 61/2 SDAF 22536
22236 CCK/W33
265 000
1 300
SNW 36
SDAF 536
SR 36-30
LOR 148
EPR 19
TER 148
403
615/16
613/16, 67/8, 7
SDAF 22538
22238 CCK/W33
286 000
1 200
SNW 38
SDAF 538
SR 38-32
LER 224
EPR 21
TER 224
454
73/16
71/8, 71/4
SDAF 22540
22240 CCK/W33
328 000
1 100
SNW 40
SDAF 540
SR 40-34
LER 228
EPR 22
TER 228
544
715/16
713/16, 77/8, 8
SDAF 22544
22244 CCK/W33
396 000
950
SNW 44
SDAF 544
SR 44-38
LER 236
EPR 24
TER 236
795
*Available in steel only
388

SDAF 22500
How to order
SDAF 22520
Option
Specify
One end closed

Taconite seals
Cast-steel
Optional shaft size
SDAF 22520Y
SDAF 22520T
SDAFS 22520
SDAF 22520 x 312

Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 22520
41/2
151/4
17/8
131/8
115/8
33/8
815/16
121/32
63/4
(4)-3/4
159/64
43/4
SDAFS 22522
415/16
161/2
63/4
21/8
141/2
125/8
97/8
113/16
71/4
(4)-7/8
21/8
47/8
SDAF 22524
51/4
161/2
67/8
21/4
141/2
131/4
41/8
101/2
127/32
73/8
(4)-7/8
29/32
415/16
SDAF 22526
183/8
71/2
23/8
16
145/8
41/2
117/8
211/32
(4)-1
215/32
51/4
SDAFS 22528
201/8
71/2
23/8
171/8
16
41/2
121/16
21/8
713/16
(4)-11/8
SDAF 22530
65/16
211/4
77/8
21/2
181/4
17
43/4
129/16
21/32
83/8
(4)-11/8
249/64
57/16
SDAF 22532
611/16
22
81/4
21/2
191/4
173/8
137/16
23/32
83/4
(4)-11/8
231/32
55/8
SDAF 22536
71/2
263/4
93/8
23/4
235/8
207/8
57/8
153/16
23/8
10
(4)-11/4
39/64
61/8
SDAF 22538
77/8
275/8
10
231/2
211/2
61/4
16
27/16
105/8
(4)-13/8
319/64
61/2
SDAF 22540
81/4
283/4
101/2
31/4
25
23
63/4
167/8
21/2
111/8
(4)-13/8
31/2
67/8
SDAF 22544
91/2
32
111/4
31/2
277/8
255/8
71/4
19
31/8
117/8
(4)-11/2
35/8
71/8
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
389

SDAF 22600
How to order
SDAF 22617
Option
Specify
One end closed

Taconite seals
Cast-steel
Optional shaft size
SDAF 22617Y
SDAF 22617T
SDAFS 22617
SDAF 22617 x 3
Held and free: Standard and standard option blocks come with an enclosed stabilizing ring. For a free unit, discard the enclosed stabilizing
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional
in
Bearing
basic load
rating
dynamic
C
LER / LOR Adapter

grease
assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
215/16
213/16, 27/8, 3
SDAF 22617
22317 CCK/W33
108 000
1 900
SNW 117
SDAF 617
SR 20-17
LER 59
EPR 10
TER 59
84
37/16
35/16, 33/8, 31/2 SDAF 22620
22320 CCK/W33
160 000
1 700
SNW 120
SDAF 620
SR 24-20
LER 75
EPR 11
TER 75
164
315/16
313/16, 37/8, 4
SDAF 22622
22322 CCK/W33
187 000
1 600
SNW 122
SDAF 622
SR 0-22
LER 93
EPR 13
TER 93
178
43/16
41/16, 41/8, 41/4 SDAF 22624
22324 CCK/W33
217 000
1 400
SNW 124
SDAF 624
SR 0-24
LOR 113
EPR 14
TER 113
272
47/16
45/16, 43/8, 41/2 SDAF 22626
22326 CCK/W33
252 000
1 300
SNW 126
SDAF 626
SR 0-26
LOR 117
EPR 15
TER 117
340
57/16
53/8, 51/2
SDAF 22632
22332 CCK/W33
360 000
950
SNW 132
SDAF 632
SR 38-32
LER 211
EPR 17
TER 211
455
515/16
513/16, 57/8, 6
SDAF 22634
22334 CCK/W33
396 000
950
SNW 134
SDAF 634
SR 40-34
LER 215
EPR 19
TER 215
530
67/16
65/16, 63/8, 61/2 SDAF 22636
22336 CCK/W33
450 000
900
SNW 136
SDAF 636
SR 0-36
LER 220
EPR 26
TER 220
630
615/16
613/16, 67/8, 7
22338 CCK/W33
477 000
850
SNW 138
SDAF 638
SR 44-38
LER 224
EPR 21
TER 224
792
SDAF 22638
390

SDAF 22600
How to order
SDAF 22617
Option
Specify
One end closed

Taconite seals
Cast-steel
Optional shaft size
SDAF 22617Y
SDAF 22617T
SDAFS 22617
SDAF 22617 x 3

Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
815/16
125/32
63/4
(4)-3/4
21/16
411/16
(No. reqd)
in
SDAF 22617
41/2
151/4
17/8
131/8
115/8
33/8
SDAF 22620
51/4
161/2
67/8
21/4
141/2
131/4
41/8
101/2
21/32
73/8
(4)-7/8
27/16
51/16
SDAF 22622
183/8
71/2
23/8
16
145/8
41/2
117/8
213/32
(4)-1
25/8
51/4
SDAF 22624
65/16
211/4
77/8
21/2
181/4
17
43/4
129/16
213/32
83/8
(4)-11/8
213/16
57/16
SDAF 22626
611/16
22
81/4
21/2
191/4
173/8
137/16
215/32
83/4
(4)-11/8
55/8
SDAF 22632
77/8
275/8
10
231/2
211/2
61/4
16
223/32
105/8
(4)-13/8
35/8
61/2
SDAF 22634
81/4
283/4
101/2
31/4
25
23
63/4
167/8
23/4
111/8
(4)-13/8
33/4
63/4
SDAF 22636
87/8
301/2
103/4
31/4
263/8
241/8
67/8
1715/16
31/16
113/8
(4)-11/2
315/16
67/8
SDAF 22638
91/2
32
111/4
31/2
277/8
255/8
71/4
19
313/32
117/8
(4)-11/2
41/16
71/8
/16
/16
/16
/16
/16
/16
/16
/16
/16
391

Nomenclature / TY-RPA top angle take-up units
TY 307 RPA-30
1
4
3
1. Prefix:
2. Shaft size:
4. Travel code:
TY
Inches
Total travel length in inches
07
16ths of an inch
(i.e. 3716)
Take-up housing
(One end closed as standard)
3. Style:
RPA
392
Top angle, protected screw

take-up frame
Nomenclature / TFT-RPA top angle take-up units
TFT
44-24
3
1
2
1. Prefix:
2. Frame size designation:
3. Travel code:
TFT
Appropriate SAF housings and shaft sizes

are indicated in dimension tables
Total travel length in inches
Top mount take-up frame
393

Take-up frames / top angle
TY-RPA
12" - 36" Adjustment
Protected screw
Steel
How to order
TY 107 RPA-12
Option
Specify
One end closed

Both ends open
TY 107 RPA-12
TY 107 RPA-12-26
Held and free: Specify the appropriate stabilizing rings for a held unit; two required.
For shaft diameter tolerances see page 351; for bearing information see page 147.
Shaft
dia.
Designations
Take-up
standard
unit
Take-up unit
both ends open
Bearing
S-1
in
Bearing
basic load
rating
dynamic
C
Bearing
grease
speed
limit
lbs
r/min
Mass
Adapter
assembly
Take-up
Take-up
housing
frame
standard
unit
One end closed
Stab.
ring
(2 reqd)
Travel
code
in
lbs
17/16
TY 107 RPA-12
TY 107 RPA-18
TY 107 RPA-24
TY 107R PA-12-26
TY 107R PA-18-26
TY 107R PA-24-26
22209 CCK/W33
20 200
5 300
SNW 9
TY 107 R
TY 107 R
TY 107 R
PA 12-1
PA 18-1
PA 24-1
SR 9-9
12
18
24
42
48
54
115/16
TY 115 RPA-12
TY 115 RPA-18
TY 115 RPA-24
TY 115R PA-12-26
TY 115R PA-18-26
TY 115R PA-24-26
22211 EK
30 100
4 500
SNW 11
TY 115 R
TY 115 R
TY 115 R
PA 12-2
PA 18-2
PA 24-2
SR 11-0
12
18
24
51
55
63
2 /16
TY 203 RPA-12
TY 203 RPA-18
TY 203 RPA-24
TY 203 RPA-30
TY 203 RPA-36
TY 203R PA-12-26
TY 203R PA-18-26
TY 203R PA-24-26
TY 203R PA-30-26
TY 203R PA-36-26
SNW 13
TY 203 R
TY 203 R
TY 203 R
TY 203 R
TY 203 R
PA 12-4
PA 18-4
PA 24-4
PA 30-4
PA 36-4
SR 13-0
12
18
24
30
36
85
96
110
120
130
27/16
TY 207 RPA-12
TY 207 RPA-18
TY 207 RPA-24
TY 207 RPA-30
TY 207 RPA-36
TY 207R PA-12-33
TY 207R PA-18-33
TY 207R PA-24-33
TY 207R PA-30-33
TY 207R PA-36-33
SNW 15
TY 207 R
TY 207 R
TY 207 R
TY 207 R
TY 207 R
PA 12-4
PA 18-4
PA 24-4
PA 30-4
PA 36-4
SR 15-0
12
18
24
30
36
92
105
110
120
130
215/16
TY 215 RPA-12
TY 215 RPA-18
TY 215 RPA-24
TY 215 RPA-30
TY 215 RPA-36
TY 215R PA-12-33
TY 215R PA-18-33
TY 215R PA-24-33
TY 215R PA-30-33
TY 215R PA-36-33
SNW 17
TY 215 R
TY 215 R
TY 215 R
TY 215 R
TY 215 R
PA 12-5
PA 18-5
PA 24-5
PA 30-5
PA 36-5
SR 17-14
12
18
24
30
36
100
115
130
140
155
22213 EK
22215 EK
22217 CCK/W33
394
43 400
47 700
55 100
3 800
3 400
3 000

TY-RPA
Protected screw, steel frame
Cast-iron housing
Grease lubrication
Piston ring seals
Option
Both ends open
Standard
One end closed
How to order
TY 107 RPA-12
Option
Specify
One end closed

Both ends open
TY 107 RPA-12
TY 107 RPA-12-26
Designations
Take-up
standard
unit
One end closed
Rod
dia.
A
Bolt
dia.
in
TY 107 RPA-12
TY 107 RPA-18
TY 107 RPA-24
315/16
281/2
341/2
401/2
35/8
261/2
321/2
381/2
81/4
71/4
41/8
13/4
11/16
31
/32
23/8
TY 115 RPA-12
TY 115 RPA-18
TY 115 RPA-24
43/16
291/2
351/2
411/2
35/8
271/2
331/2
391/2
85/8
73/4
41/8
115/16
13/16
11/16
29/16
51/8
321/2
381/2
441/2
501/2
561/2
301/2
361/2
421/2
481/2
541/2
105/8
91/4
51/2
51/8
51/8
21/8
13/8
11/4
25/8
51/8
321/2
381/2
441/2
501/2
561/2
301/2
361/2
421/2
481/2
541/2
105/8
91/4
51/2
51/8
51/8
21/8
17/16
19/32
25/8
55/8
341/2
401/2
461/2
521/2
581/2
32
38
44
50
56
11/8
113/4
55/8
21/2
19/16
113/32
215/16
TY 203 RPA-12
TY 203 RPA-18
TY 203 RPA-24
TY 203 RPA-30
TY 203 RPA-36
TY 207 RPA-12
TY 207 RPA-18
TY 207 RPA-24
TY 207 RPA-30
TY 207 RPA-36
TY 215 RPA-12
TY 215 RPA-18
TY 215 RPA-24
TY 215 RPA-30
TY 215 RPA-36
45/8
45/8
45/8
/8
/8
/2
/2
/2
/4
/4
/8
/8
/8
/8
/4
10
395

TY-RPA
Cast-iron housing
Grease lubrication
Piston ring seals
How to order
TY 107 RPA-12
Option
Specify
One end closed

Both ends open
TY 107 RPA-12
TY 107 RPA-12-26
Shaft
dia.
Designations
Take-up
standard
unit
Take-up unit
both ends open
Bearing
S-1
in
Bearing
basic load
rating
dynamic
C
Bearing
grease
speed
limit
lbs
r/min
37/16
TY 307 RPA-12
TY 307 RPA-18
TY 307 RPA-24
TY 307 RPA-30
TY 307 RPA-36
TY 307R PA-12-33
TY 307R PA-18-33
TY 307R PA-24-33
TY 307R PA-30-33
TY 307R PA-36-33
22220 CCK/W33
81 000
2 200
315/16
TY 315 RPA-12
TY 315 RPA-18
TY 315 RPA-24
TY 315 RPA-30
TY 315R PA-12-39
TY 315R PA-18-39
TY 315R PA-24-39
TY 315R PA-30-39
22222 CCK/W33
105 000
2 000
4 /16
TY 407 RPA-12
TY 407 RPA-18
TY 407 RPA-24
TY 407 RPA-30
TY 407R PA-12-32
TY 407R PA-18-32
TY 407R PA-24-32
TY 407R PA-30-32
22226 CCK/W33
142 000
415/16
TY 415 RPA-12
TY 415 RPA-18
TY 415 RPA-24
TY 415 RPA-30
TY 415 RPA-12-32
TY 415 RPA-18-32
TY 415 RPA-24-32
TY 415 RPA-30-32
22228 CCK/W33
160 000
5 /16
TY 507 RPA-12
TY 507 RPA-18
TY 507 RPA-24
TY 507 RPA-30
TY 507 RPA-12-29
TY 507 RPA-18-29
TY 507 RPA-24-29
TY 507 RPA-30-29
22232 CCK/W33
225 000
515/16
TY 515 RPA-12
TY 515 RPA-18
TY 515 RPA-24
TY 515 RPA-30
TY 515 RPA-12-33
TY 515 RPA-18-33
TY 515 RPA-24-33
TY 515 RPA-30-33
22234 CCK/W33
252 000
396
Mass
Adapter
assembly
Take-up
Take-up
housing
frame
standard
unit
One end closed
Stab.
ring
(2 reqd)
Travel
code
in
lbs
155
175
190
205
220
SNW 20
TY 307 R
TY 307 R
TY 307 R
TY 307 R
TY 307 R
PA 12-6
PA 18-6
PA 24-6
PA 30-6
PA 36-6
SR 20-17
12
18
24
30
36
SNW 22
TY 315 R
TY 315 R
TY 315 R
TY 315 R
PA 12-6
PA 18-6
PA 24-6
PA 30-6
SR 22-19
12
18
24
30
155
170
190
205
1 800
SNW 26
TY 407 R
TY 407 R
TY 407 R
TY 407 R
PA 12-7
PA 18-7
PA 24-7
PA 30-7
SR 26-0
12
18
24
30
270
280
290
300
1 700
SNW 28
TY 415 R
TY 415 R
TY 415 R
TY 415 R
PA 12-8
PA 18-8
PA 24-8
PA 30-8
35072-28
12
18
24
30
450
470
490
510
1 500
SNW 32
TY 507 R
TY 507 R
TY 507 R
TY 507 R
PA 12-9
PA 18-9
PA 24-9
PA 30-9
35072-32
12
18
24
30
615
640
670
690
1 300
SNW 34
TY 515 R
TY 515 R
TY 515 R
TY 515 R
PA 12-10
PA 18-10
35072-34
PA 24-10
PA 30-10
12
18
24
30
850
890
930
970

TY-RPA
Cast-iron housing
Grease lubrication
Piston ring seals
Option
Both ends open
Standard
One end closed
How to order
TY 107 RPA-12
Option
Specify
One end closed

Both ends open
TY 107 RPA-12
TY 107 RPA-12-26
Designations
Take-up
standard
unit
One end closed
Rod
dia.
A
21/2
Bolt
dia.
H
11/4
141/2
12
67/8
21/2
115/16
13/4
37/16
in
381/2
441/2
501/2
561/2
621/2
53/4
36
42
48
54
60
381/2
441/2
501/2
561/2
5 /4
36
42
48
54
21/2
11/4
141/2
12
67/8
27/8
21/8
131/32
313/16
381/2
441/2
501/2
561/2
53/4
36
42
48
54
21/2
13/8
163/4
12
31/16
21/2
29/32
41/4
TY 415 RPA-12
TY 415 RPA-18
TY 415 RPA-24
TY 415 RPA-30
81/2
481/2
541/2
601/2
661/2
67/8
441/2
501/2
561/2
621/2
33/8
13/4
191/8
161/4
71/8
35/8
25/8
213/32
41/8
TY 507 RPA-12
TY 507 RPA-18
TY 507 RPA-24
TY 507 RPA-30
9 /2
521/2
581/2
641/2
701/2
8 /4
481/2
541/2
601/2
661/2
51/2
217/8
11/8
181/4
101/8
315/16
225/32
315/16
571/2
631/2
691/2
751/2
54
60
66
72
233/16
11/4
21
101/8
43/16
31/8
215/16
413/16
TY 307 RPA-12
TY 307 RPA-18
TY 307 RPA-24
TY 307 RPA-30
TY 307 RPA-36
TY 315 RPA-12
TY 315 RPA-18
TY 315 RPA-24
TY 315 RPA-30
TY 407 RPA-12
TY 407 RPA-18
TY 407 RPA-24
TY 407 RPA-30
TY 515 RPA-12
TY 515 RPA-18
TY 515 RPA-24
TY 515 RPA-30
10 /2
9 /8
/2
/2
/2
/8
/4
/8
/4
/4
/4
397

Used with SAF 22500 pillow block
How to order
17/16" shaft, 12" travel

SAF 22509
Option
Specify
Frame
Pillow block
TFT 01-12
SAF 22509
Shaft
dia.
Designations
Basic
frame part
Pillow block
Mass
Travel
code
S-1
in
lbs
17/16
SAF 22509
TFT 01-XX
111/16
115/16
SAF 22510
TFT 02-XX
23/16
TFT 03-XX
SAF 22515
211/16
SAF 22516
TFT 04-XX
215/16
33/16
37/16
SAF 22517
TFT 05-XX
TFT 06-XX
398
31
37
43
49
55
29
35
41
47
53
30
35
40
50
56
18
24
30
36
411/4
471/4
531/4
591/4
383/4
443/4
503/4
563/4
125
130
135
140
18
24
30
36
48
441/4
501/4
561/4
621/4
741/4
413/4
471/2
531/2
591/2
711/2
180
190
205
215
235
18
24
30
36
48
46
52
58
64
76
431/4
491/4
551/4
611/4
731/4
195
210
215
230
245
SAF 22511
SAF 22513
27/16
12
18
24
30
36
SAF 22518
SAF 22520

TFT (Pillow Block not included)
Designations
Basic
frame part
Bolts
(No. reqd)
A
Frame
slot
Rod
dia.
C1
How to order

SAF 22509
Option
Specify
Frame
Pillow block
TFT 01-12
SAF 22509
Bolt
dia.
H
L
Max
L
Min
in
21/4
TFT 01-XX
95/8
13
/16
(2)- /2-13 x 2LG
/16 x 2 /4
2 /2
TFT 02-XX
23/4
51/4
11
4 /16
81/2
/8
57/8
/16
(2)-5/8-11 x 21/4LG
11
/16 x 21/8
77/8
515/16
31/4
/16 x 2 /4
6 /4
13 /4
/8
9 /8
6 /16
10 /8
15/8
13/16
3
137/8
15
(2)- /4-10 x 2 /2LG

3
/16 x 3 /4
11
3
3 /4
43/4
6 /8
11/8
31/2
123/16
11
(2)-5 /8-11 x 2 /4LG
10
101/2
1
5
TFT 04-XX
15
3
TFT 03-XX
7
21/2
11
1 /4
TFT 05-XX
(2)-3/4-10 x 3LG
15/8
13
TFT 06-XX
41/2
(2)-7/8-9 x 31/4LG
13/4
15
11/4
141/2
11/4
16
7 /16
113/4
/4
/16 x 21/8
/16 x 33/4
13
/4
115/8
103/8
131/8
91/4
81/2
145/16
143/4
125/8
81/2
153/4
399

How to order

FSAF 22515
Option
Specify
Frame
Pillow block
TFT 43-18
FSAF 22515
Shaft
dia.
Designations
Basic
frame part
Pillow block
Mass
Travel
code
S-1
in
lbs
2 /16
TFT 43-XX
FSAF 22515
211/16
TFT 34-XX
FSAF 22516
215/16
TFT 44-XX
FSAF 22517
33/16
TFT 36-XX
FSAF 22518
37/16
TFT 46-XX
FSAF 22520
315/16
TFT 37-XX
SAF 22522
47/16
TFT 38-XX
SAF 22526
415/16
TFT 48-XX
SAF 22528
400
18
24
30
36
411/4
471/4
531/4
591/4
383/4
443/4
503/4
563/4
125
130
135
140
18
24
30
36
48
441/4
501/4
561/4
621/4
741/4
411/2
471/2
531/2
591/2
711/2
180
190
205
215
235
18
24
30
36
48
46
52
58
64
76
431/4
491/4
551/4
611/4
731/4
195
210
215
230
245
18
24
30
36
48
50
56
62
68
80
471/4
531/4
591/4
651/4
771/4
330
340
360
370
390
18
24
30
36
48
551/2
611/2
671/2
731/2
851/2
53
59
65
71
83
425
440
460
480
500

Designations
Basic
frame part
Bolts
(No. reqd)
A
Frame
hole
Rod
dia.
How to order

FSAF 22515
Option
Specify
Frame
Pillow block
TFT 43-18
FSAF 22515
Bolt
dia.
C1
61/4
91/8
65/8
125/8
43/4
17/8
21/8
in
TFT 43-XX
31/4
(4)-1/2-13 x 21/4LG
11/8
TFT 34-XX
31/2
(4)-5/8-11 x 21/2LG
13/16
/16
/16
(4)- /8-11 x 2 /2LG
1 /4
TFT 36-XX
(4)-5/8-11 x 3LG
15/8
11
1 /4
13
13
TFT 46-XX
4 /2
(4)- /4-10 x 3 /4LG
TFT 37-XX
415/16 (4)-3/4-10 x 31/2LG
(4)-7/8-9 x 33/4LG
TFT 38-XX
/16
14 /4
137/8
3
/4
11/4
16
11 /4
8 /2
14 /16
11
143/4
125/8
/4
81/2
11/4
20
/4
139/16
145/8
81/2
155/16
1 /2
7 /4
23 /2
17 /2
169/16
165/8
23/8
71/4
191/4
1
/8
21/8
153/4
12 /8
/16
11/16
10 /16
15
2 /8
(4)-1-8 x 33/4LG
/16
6
TFT 48-XX
1 /4
/16
3
103/8
3 /4
TFT 44-XX
/8
105/16
11
131/4
23/4
31/4
1
10 /8
8 /2
191/2
33/8
401
Notes
402
Nomenclature / SAW split pillow blocks
SAW
23540 -TY
3
1
2
1. Housing style:
2. Designation:
Mounting method
232(00)
232(00) CC/W33
Cylindrical
Inch dimensions
235(00)
235(00) CCK/W33
Adapter
Wide bearing seat
3. Suffix:
T
TV
Taconite V-ring seal
TA or TVA
Taconite seal with button head grease fitting
TB or TVB
Taconite seal with giant button head grease fitting
One end closed (i.e.,supplied with end plug)
TLC
PosiTrac Plus seals
403

SAW 23200
Custom manufactured
How to order
SAW 23220
Option
Specify
One end closed

Taconite seals
PosiTrac Plus seals
SAW 23220 Y
SAW 23220 T
SAW 23220-TLC
Housing style N
Shaft
Designations
dia.
da
Complete
pillow block
Bearing
S-2 S-3
in
Bearing
basic load
rating
dynamic
C
LOR
grease
speed
limit
lbs
r/min
Lock- LockPillow
nut
washer block
housing
Mass
Stab.
ring
(1 reqd)
Triple ring
End
seal
plug
S-2 shaft S-3 shaft
(1 reqd)
(1 reqd)
Taconite
seal
S-2
S-3
lbs
100
41/2 313/16 SAW 23220
23220 CC/W33
107 000
1 700
AN 20 W 20
SAW 220
SR 20-17 LOR 118
LOR 106
80
130
57/8 415/16 SAW 23226
23226 CC/W33
175 000
1 300
AN 26 W 26
SAW 226
SR 26-0
LOR 136
LOR 122
155
140
61/4 55/16 SAW 23228
23228 CC/W33
206 000
1 200
AN 28 W 28
SAW 228
SR 28-0
LOR 144
LOR 127
180
190
83/8 71/4 SAW 23238
23238 CC/W33
329 000
850
AN 38 W 38
SAW 238
SR 38-32 LOR 171
LOR 160
430
200
83/4 75/8 SAW 23240
23240 CC/W33
418 000
850
AN 40 W 40
SAW 240
SR 40-34 LOR 175
LOR 164
515
220
99/16 85/16 SAW 23244
23244 CC/W33
531 000
750
N 44
SAW 244
SR 44-38 LOR 179
LOR 170
710
W 44
NOTE: All housings are made to order, as an alternative, consider SAFD housings.
404

SAW 23200
Custom manufactured
How to order
SAW 23220
Option
Specify
One end closed

Taconite seals
PosiTrac Plus seals
SAW 23220 Y
SAW 23220 T
SAW 23220-TLC
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
T2
T3
in
SAW 23220
41/2
151/4
43/8
13/4
131/8
115/8
23/8
83/4
63/16
/16
(4)-3/4
21/16
SAW 23226
183/8
51/8
23/8
16
145/8
31/4
115/16
23/8
81/2
/16
(4)-7/8
23/4
51/2
51/2
SAW 23228
201/8
57/8
23/8
171/8
16
33/8
113/4
21/16
91/8
/16
(4)-1
231/32
53/4
53/4
SAW 23236
71/2
263/4
71/8
235/8
207/8
45/8
147/8
27/16
103/8
/16
(4)-1
321/32
61/2
61/2
SAW 23238
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
21/2
107/8
/16
(4)-11/4
327/32
71/2
SAW 23240
81/4
291/2
33/8
25
221/2
161/2
29/16
113/8
/16
(4)-11/4
41/16
711/16
71/16
SAW 23244
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
33/16
121/8
/16
(4)-11/2
415/32
81/16
405

SAW 23500
Custom manufactured
How to order
SAW 23520
Option
Specify
One end closed

Taconite seals
PosiTrac Plus seals
SAW 23520 Y
SAW 23520 T
SAW 23520TLC
Housing style N
Shaft
dia.
S-1
Designations
Complete
pillow block
Bearing
in
Bearing
basic load
rating
dynamic
C
LOR
grease
speed
limit
lbs
r/min
Adapter
assembly
Mass
Pillow
block
housing
Stab.
ring
(1 reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
37/16
SAW 23520
23220 CCK/W33
107 000
1 700
SNW 120
SAW 520
SR 20-17
LOR 102
EPR 12
TER 102
47/16
SAW 23526
23226 CCK/W33
175 000
1 300
SNW 126
SAW 526
SR 26-0
LOR 117
EPR 15
TER 117
155
415/16
SAW 23528
23228 CCK/W33
206 000
1 200
SNW 128
SAW 528
SR 28-0
LOR 122
EPR 27
TER 122
180
615/16
SAW 23538
23238 CCK/W33
329 000
850
SNW 138
SAW 538
SR 38-32
LOR 155
EPR 21
TER 155
430
73/16
SAW 23540
23240 CCK/W33
418 000
850
SNW 140
SAW 540
SR 40-34
LOR 159
EPR 21
TER 159
515
715/16
SAW 23544
23244 CCK/W33
531 000
750
SNW 144
SAW 544
SR 44-38
LOR 167
EPR 23
TER 167
710
Note: All housings are made to order; as an alternative consider SAFD housings.
406

SAW 23500
Custom manufactured
How to order
SAW 23520
Option
Specify
One end closed

Taconite seals
PosiTrac Plus seals
SAW 23520 Y
SAW 23520 T
SAW 23520TLC
Designations
Complete
pillow block
A
E
Max
E
Min
Static
oil
level
K
Bolts
(No. reqd)
in
SAW 23520
41/2
151/4
43/8
13/4
131/8
115/8
23/8
83/4
613/16
/16
(4)-1/2
21/16
SAW 23526
183/8
51/8
23/8
16
145/8
31/4
115/16
23/8
81/2
/16
(4)-7/8
23/4
51/2
SAW 23528
201/8
57/8
23/8
171/8
16
33/8
113/4
21/16
91/8
/16
(4)-1
231/32
523/32
SAW 23538
77/8
28
71/2
31/8
243/8
215/8
41/2
1511/16
21/2
107/8
/16
(4)-11/4
327/32
623/32
SAW 23540
81/4
291/2
33/8
25
221/2
161/2
29/16
113/8
/16
(4)-11/4
41/16
71/8
SAW 23544
91/2
323/4
83/4
33/4
277/8
243/4
51/4
185/8
33/16
121/8
/16
(4)-11/2
415/32
711/32
407

Nomenclature / SDAF extended range
Standards
SDAF
23076 KAT x 131516
4
2
1. Housing style:
2. Designation:
Complete assembly
(cast-iron)
Mounting
method
Housing only
Heavy duty series
230(00)
30(00)
230(00) CC/W33
Cylindrical
Inch dimensions
231(00)
31(00)
231(00) CC/W33
Cylindrical
Triple ring seal
232(00)
32(00)
232(00) CC/W33
Cylindrical
230(00)KA
30(00)KA
230(00) CCK/W33
Adapter
231(00)KA
31(00)KA
231(00) CCK/W33
Adapter
232(00)KA
32(00)KA
232(00) CCK/W33
Adapter
3. Suffix:
T
Standard triple ring seal
408
4. Shaft size:
Adapter mounted
Engineering specials
Y 10056 BL
1
3
2
3. Suffix:
1. Prefix:
Y or Z
Drawing size
Old
HC
Housing only
Free
(both ends open)
BL
Held
(both ends open)
BF
Free
(one end closed)
AL
Held
(one end closed)
AF
2. Designation:
Sequential drawing number
New
409

Introduction / SDAF extended range
Introduction
Mounting
Sealing options
SKF is the leading supplier of split pillow blocks

in the US and has established many of the
designs that are regarded as the industry
standards today. This position is due, in part, to
the fact that SKF is a full range supplier of split
pillow block housings and the associated
bearings and mounting accessories for shafts
ranging from 17/16" to over 20" in diameter. The
largest size split pillow blocks, for 9" to 20"
shafts, are referred to as the extended range
series and are supplied as made-to-order,
customized solutions for the largest and most
demanding split pillow block applications.
The extended range series of pillow blocks
are a rugged housing style of exceptionally
sturdy 4-bolt construction. The standard
material is class 40 gray iron but when extra
high strength or impact resistance is necessary,
housings can be supplied in high strength ductile
irons or cast steel as specified below. Extended
range housings are machined according to the
requirements of the individual application and
are, therefore, highly customized bearing
solutions. These customized housings are each
given their own specific part number and
drawing so that there is a permanent record for
each housing.
When no special features are required,
housings are designated according to the part
numbers in the following tables. However, since
extended range housings are not stocked in a
final machined state, it is recommended that
each application for extended range housings be
reviewed with SKF Applications Engineering to
determine what features may be needed since
many special features can often be
accommodated with little or no additional cost.
Because of their size, extended range housings

often require special considerations when
mounting and dismounting. For bearings
mounted directly on the shaft, it is
recommended that hydraulic assist features be
included in the shaft design. These will aid in
mounting and dismounting the bearing. For
bearings mounted on adapter sleeves, sleeves
can be supplied modified with hydraulic assist
features which, once again, aid in both mounting
and dismounting. SKF Applications Engineering
can provide the appropriate recommendations
and drawings for hydraulic assist as well as
instructions for extended range housing
assembly.
Triple ring seals of steel material for high

wear resistance and strength in severe
environments
Special labyrinth ring seals with O-ring bore
inserts for enhanced lubricant retention in oil
applications
Two-piece, bolt-on Taconite seal or TER
cartridge type Taconite seals
One end closed enclosures to provide superior
sealing ability with ease of assembly and
maintenance
Housing material
Standard material is ASTM A48B class 40
gray iron
Alternate high strength or impact resistant
material available
Ductile-Iron: ASTM A339
Grade 60-45-10
Ductile-Iron: ASTM A536
Grade 80-60-03
Cast-Steel: ASTM A27
Grade U-60-30
Lubrication
Housing design will provide effective bearing
lubrication with choice of conventional
greasing methods, static oil or pressurized
circulating oil system
Readily adaptable for use with custom
lubrication systems and auxiliary monitoring
devices
410
Custom considerations
Because of the highly specialized nature
of the extended range applications, SKF
Mounted Products Design and Applications
Engineering work together to specify and design
each pillow block. This flexible approach to
supplying extended range pillow blocks provides
the user with a host of optional features that
tailor to the specific application. These features
can include, but are not limited to: drilled base
bolt holes, milled foot pads, special machinings
for lubrication and condition monitoring systems,
special bore tolerances, machined foot ends,
special seals, machinings for user supplied
auxiliary seals, hydraulic assisted adapter
sleeves, etc. The extended range series pillow
blocks are individually engineered to provide a
safe, reliable, cost effective bearing solution for
the application. Consult SKF Applications
Engineering for your particular needs.
Availability
SKF extended range housings are
made-to-order to accommodate any special
features that may be required. So that orders
can be filled quickly, SKF stocks unmachined
castings for the most popular sizes, and can
turn around most finished products with
reduced lead times.
Application information / SDAF extended range
Application: (Please note type of equipment where pillow blocks are to be used.)
Purpose: (Is this installation part of a new design or a replacement? If the latter, please indicate what unit is presently used.)
Why is the present unit being replaced? (Please explain.)

Present unit is defective:
Equipment is being modified or upgraded:
What type of load is the pillow block intended to carry?
Radial
Steady
Mild shock
Direction_____________________Speed______rpm
Axial
Temperature_____ F
Type of lubrication available:

Grease
Oil
Oil Mist
Conditions under which pillow block will be used:
Wet
Dry
Alternating
Heavy shock
Required Life______hours (L10)
Static
Circulating
Exposed
Covered
Type of drive mechanism to be used:

Shaft diameter range (specify):
Will unit use a cylindrical or adapter mounted (tapered) bore?
What special requirements will be needed?
Center height:
Bolt configuration and spacing:
Sealing material:
Other:
Name:___________________________________________________________ Title:
Company:
Address:
City:__________________________
State:_____________
Zip:_____________
Email:____________________________________________________________________
Phone: (
Cell Phone: (
)
)
Send this form plus any design details or drawings information you wish to include to your local SKF sales representative.
411

Extended range / cylindrical mount
SDAF 23000
ERF triple ring seals
Custom manufactured
How to order
These housings are made-to-order,
customized bearing solutions and should be
reviewed by our application engineers. Please
refer to page 411 for required application
information.
Shaft
Designations
dia.
Complete
pillow block
Bearing
S-3
Bearing
basic load
rating
dynamic
C
ERF
grease
speed
limit
lbs
r/min
Locknut
Lockplate
Mass
Pillow
block
housing
Stab.
ring
Triple ring
seal
S-2 shaft
(1 reqd)
da
S-2
mm
in
300
13
111/2
SDAF 23060
23060 CA/W33
413 000
800
N 060
PL 60
SDAF 3060
(1)-A 8967
ERF 824
ERF 832
1 200
320
133/4
121/4
SDAF 23064
23064 CA/W33
441 000
800
N 064
PL 64
SDAF 3064
(1)-A 8968
ERF 943
ERF 804
1 300
340
15
13
SDAF 23068
23068 CA/W33
528 000
700
N 068
PL 68
SDAF 3068
(1)-A 8969
ERF 806
ERF 824
1 550
360
153/4
133/4
SDAF 23072
23072 CA/W33
537 000
670
N 072
PL 72
SDAF 3072
(1)-A 8970
ERF 969
ERF 874
1 650
380
163/4
141/2
SDAF 23076
23076 CA/W33
557 000
630
N 076
PL 76
SDAF 3076
(1)-A 8971
ERF 822
ERF 950
1 700
400
171/2
153/8
SDAF 23080
23080 CA/W33
647 000
600
N 080
PL 80
SDAF 3080
(1)-36053-153 ERF 999
ERF 942
2 300
420
18
16
SDAF 23084
23084 CA/W33
672 000
450
N 084
PL 84
SDAF 3084
(1)-36053-143 ERF 812
ERF 809
2 300
440
191/2
17
SDAF 23088
23088 CA/W33
724 000
430
N 088
PL 88
SDAF 3088
(2)-36053-150 ERF 926
ERF 838
2 550
460
20
173/4
SDAF 23092
23092 CA/W33
776 000
400
N 092
PL 92
SDAF 3092
(2)-36053-152 ERF 808
ERF 906
2 850
480
21
181/2
SDAF 23096
23096 CA/W33
751 000
380
N 096
PL 96
SDAF 3096
(2)-36053-200 ERF 933
ERF 978
4 250
500
21
19
SDAF 230/500
230/500 CA/W33
827 000
380
N 500
PL 500
SDAF 30/500
(2)-36053-165 ERF 933
ERF 922
4 350
530
221/2
203/8
SDAF 230/530
230/530 CA/W33
982 000
340
N 530
PL 530
SDAF 30/530
(2)-36053-166 ERF 997
ERF 998
5 200
Note: All SDAF series are custom manufactured

412
(No. reqd)
S-3 shaft
(1 reqd)
lbs

SDAF 23000
Custom manufactured
How to order
These housings are made-to-order, customized
bearing solutions and should be reviewed by our
application engineers. Please refer to page 411 for
required application information.
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23060
12
381/4
143/4
331/2
323/4
331/8
237/16
43/8
151/2
/16
(4)-15/8
411/32
183/8
SDAF 23064
12
381/4
143/4
331/2
323/4
331/8
237/16
151/2
/16
(4)-15/8
41/2
193/8
SDAF 23068
12
39
151/4
43/16
331/2
32
323/4
10
24
33/8
153/4
/16
(4)-17/8
47/8
195/8
SDAF 23072
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
323/32
163/4
/16
(4)-17/8
47/8
20
SDAF 23076
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
33/8
163/4
/16
(4)-17/8
51/8
20
SDAF 23080
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
47/16
175/8
/16
(4)-2
517/32
223/4
SDAF 23084
141/2
46
171/8
51/4
403/4
391/4
40
11
29
41/16
175/8
/16
(4)-2
59/16
223/4
SDAF 23088
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
41/2
191/4
(4)-21/4
53/4
24
SDAF 23092
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
191/4
(4)-21/4
57/8
24
SDAF 23096
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
51/8
213/4
(4)-21/4
529/32
261/2
SDAF 230/500
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
43/4
213/4
(4)-21/4
61/2
261/2
SDAF 230/530
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
413/16
221/4
(4)-21/2
627/32
27
413

Extended range / adapter mount
SDAF 23000 KA
Custom manufactured
How to order
customized bearing solutions and
should be reviewed by our application
engineers. Please refer to page 411 for
Shaft dia.
Designations
S-1
Standard Optional 1)
Complete
pillow block
Bearing
in
Bearing
basic load
rating
dynamic
C
ERF Adapter
grease assembly
speed
limit
lbs
r/min
Mass
Pillow
block
housing
Stab.
ring
(No. reqd)
Triple ring
seal
(2 reqd)
End
plug
Taconite
seal
lbs
1015/16
11
SDAF 23060 KA x 1015/16 23060 CACK/W33 413 000
800
SNP 3060 x 1015/16 SDAF 3060 KA x 1015/16 (1)-A 8967
ERF 858
X-5217-9 TER 858 1 200
117/16
111/2
SDAF 23064 KA x 117/16 23064 CCK/W33
441 000
800
SNP 3064 x 117/16 SDAF 3064 KA x 117/16 (1)-A 8968
ERF 861
X-5217-16 TER 861 1 300
1115/16
12
SDAF 23064 KA x 1115/16 23064 CCK/W33
441 000
800
SNP 3064 x 1115/16 SDAF 3064 KA x 1115/16 (1)-A 8968
ERF 859
X-5217-3 TER 859 1 250
127/16
121/2
SDAF 23068 KA x 127/16 23068 CACK/W33 528 000
700
SNP 3068 x 127/16 SDAF 3068 KA x 127/16 (1)-A 8969
ERF 865
X-5217-29 TER 865 1 550
1215/16
13
SDAF 23072 KA x 1215/16 23072 CACK/W33 537 000
670
SNP 3072 x 1215/16 SDAF 3072 KA x 1215/16 (1)-A 8970
ERF 869
X-5217-28 TER 869 1 650
137/16
131/2
SDAF 23072 KA x 137/16 23072 CACK/W33 537 000
670
SNP 3072 x 137/16 SDAF 3072 KA x 137/16 (1)-A 8970
ERF 872
X-5217-27 TER 872 1 600
1315/16
14
SDAF 23076 KA x 1315/16 23076 CAK/W33
557 000
630
SNP 3076 x 1315/16 SDAF 3076 KA x 1315/16 (1)-A 8971
ERF 875
X-5217-12 TER 875 1 700
15
1415/16 SDAF 23080 KA x 15
23080 CACK/W33 647 000
600
SNP 3080 x 15
(1)-36053-153 ERF 847
X-5217-21 TER 847 2 300
153/4
SDAF 23084 KA x 153/4
23084 CAK/W33
671 000
450
SNP 3084 x 153/4 SDAF 3084 KA x 153/4
(1)-36053-143 ERF 969
X-5217-23 TER 969 2 300
161/2
SDAF 23088 KA x 161/2
23088 CAK/W33
724 000
430
SNP 3088 x 161/2 SDAF 3088 KA x 161/2
(2)-36053-150 ERF 958
**
**
2 550
17
SDAF 23092 KA x 17
23092 CAK/W33
776 000
400
SNP 3092 x 17
SDAF 3092 KA x 17
(2)-36053-152 ERF 838
**
**
2 850
18
SDAF 23096 KA x 18
23096 CAK/W33
751 000
380
SNP 3096 x 18
SDAF 3096 KA x 18
(2)-36053-200 ERF 888
**
**
4 250
181/2
SDAF 230/500 KA x 181/2 230/500 CAK/W33 827 000
380
SNP 30/500 x 181/2 SDAF 30/500 KA x 181/2 (2)-36053-165 ERF 978
**
**
4 350
191/2
SDAF 230/530 KA x 191/2 230/530 CAK/W33 982 000
340
SNP 30/530 x 191/2 SDAF 30/530 KA x 191/2 (2)-36053-166 ERF 926
**
**
5 200
**SKF will evaluate optional shaft diameters upon request.

**In these sizes, housing and seals are a matched pair and cannot be ordered separately.
1) Requires different adapter sleeve and seals.

414
SDAF 3080 KA x 15

SDAF 23000KA
Custom manufactured
How to order
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23060 KA x 1015/16
12
381/4
143/4
33/8
331/2
323/4
331/8
237/16
43/8
151/2
(4)-15/8
411/32
183/8
SDAF 23064 KA x 117/16
12
381/4
143/4
33/8
331/2
323/4
331/8
237/16
151/2
(4)-15/8
41/2
193/8
SDAF 23064 KA x 1115/16
12
381/4
143/4
33/8
331/2
323/4
331/8
237/16
151/2
(4)-15/8
41/2
193/8
SDAF 23068 KA x 127/16
1113/16
39
151/4
43/16
331/2
32
323/4
10
24
33/8
153/4
(4)-17/8
47/8
195/8
SDAF 23072 KA x 1215/16
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
323/32
163/4
(4)-17/8
47/8
20
SDAF 23072 KA x 137/16
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
323/32
163/4
(4)-17/8
47/8
20
SDAF 23076 KA x 1315/16
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
33/8
163/4
(4)-17/8
51/8
20
SDAF 23080 KA x 15
141/2
46
171/8
51/4
403/4
391/4
40
11
29
47/16
175/8
(4)-2
517/32
223/4
SDAF 23084 KA x 153/4
141/2
46
171/8
51/4
403/4
391/4
40
11
29
41/16
175/8
(4)-2
59/16
223/4
SDAF 23088 KA x 161/2
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
41/2
191/4
(4)-21/4
53/4
24
SDAF 23092 KA x 17
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
191/4
(4)-21/4
57/8
24
SDAF 23096 KA x 18
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
51/8
213/4
(4)-21/4
529/32
261/2
SDAF 230/500 KA x 181/2
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
43/4
213/4
(4)-21/4
61/2
261/2
SDAF 230/530 KA x 191/2
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
413/16
221/4
(4)-21/2
627/32
27
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
/16
415

SDAF 23100
Custom manufactured
How to order
customized bearing solutions and should
be reviewed by our application engineers.
Please refer to page 411 for required
application information.
Shaft
Designations
dia.
Complete
pillow block
da
S-2
mm
in
260
111/2
280
121/2
300
Bearing
S-3
915/16
Bearing
basic load
rating
dynamic
C
ERF
grease
speed
limit
lbs
r/min
Locknut
Lockplate
Mass
Pillow
block
housing
Stab.
ring
(2 reqd)
Triple ring
seal
S-2 shaft
(1 reqd)
S-3 shaft
(1 reqd)
lbs
SDAF 23152
23152 CA/W33
499 000
800
N 052
PL 52
SDAF 3152
36053-114 ERF 832
ERF 845
1 050
103/4
SDAF 23156
23156 CA/W33
517 000
750
N 056
PL 56
SDAF 3156
A 8967
ERF 866
ERF 826
1 250
13
111/2
SDAF 23160
23160 CA/W33
634 000
670
N 060
PL 60
SDAF 3160
36053-157 ERF 846
ERF 856
1 350
320
14
121/4
SDAF 23164
23164 CA/W33
737 000
630
N 064
PL 64
SDAF 3164
A 8970
ERF 876
ERF 983
1 850
340
15
13
SDAF 23168
23168 CA/W33
827 000
600
N 068
PL 68
SDAF 3168
36053-137 ERF 847
ERF 846
2 450
360
16
133/4
SDAF 23172
23172 CA/W33
842 000
560
N 072
PL 72
SDAF 3172
36053-167 ERF 809
ERF 874
2 500
380
17
141/2
SDAF 23176
23176 CA/W33
841 000
400
N 076
PL 76
SDAF 3176
36053-143 ERF 811
ERF 950
2 500
400
171/2
151/4
SDAF 23180
23180 CA/W33
917 000
380
N 080
PL 80
SDAF 3180
36053-150 ERF 967
ERF 895
2 800
420
181/2
153/4
SDAF 23184
23184 CA/W33
1 100 000
360
N 084
PL 84
SDAF 3184
36053-160 ERF 978
ERF 907
4 300
440
191/2
17
SDAF 23188
23188 CA/W33
1 170 000
340
N 088
PL 88
SDAF 3188
36053-165 ERF 926
ERF 838
4 300
460
20
173/4
SDAF 23192
23192 CA/W33
1 270 000
320
N 092
PL 92
SDAF 3192
36053-154 ERF 808
ERF 906
5 000
480
21
181/2
SDAF 23196
23196 CA/W33
1 370 000
300
N 096
PL 96
SDAF 3196
36053-159 ERF 933
ERF 978
5 300

416

SDAF 23100
Custom manufactured
How to order
reviewed by our application engineers.
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23152
101/4
35
131/8
33/4
301/2
29
293/4
83/4
207/8
31/8
133/4
(4)-15/8
45/8
171/2
SDAF 23156
12
381/4
143/4
331/2
323/4
331/8
237/16
41/2
151/2
(4)-15/8
425/32
19
SDAF 23160
12
381/4
143/4
331/2
323/4
331/8
237/16
37/8
151/2
(4)-15/8
51/8
19
SDAF 23164
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
41/16
163/4
(4)-17/8
517/32
203/4
SDAF 23168
14
433/4
173/4
381/4
363/4
371/2
103/4
277/8
45/8
183/4
(4)-2
529/32
221/2
SDAF 23172
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
45/8
175/8
(4)-2
531/32
213/4
SDAF 23176
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
49/32
175/8
(4)-2
61/8
213/4
SDAF 23180
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
413/16
191/4
(4)-21/4
613/32
24
SDAF 23184
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
519/32
213/4
(4)-21/4
67/8
261/2
SDAF 23188
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
55/16
213/4
(4)-21/4
77/32
261/2
SDAF 23192
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
57/16
221/4
(4)-21/2
71/2
27
SDAF 23196
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
53/16
221/4
(4)-21/2
721/32
27
417

SDAF 23100 KA
Custom manufactured
How to order
information.
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional
in
Bearing
basic load
rating
dynamic
C
ERF
grease
speed
limit
lbs
r/min
Adapter
assembly
Mass
Pillow
block
housing
Stab.
ring
(2 reqd)
Triple ring
seal
(2 reqd)
lbs
97/16
91/2
SDAF 23152 KA x 97/16
23152 CAK/W33
499 000
800
SNP 3152 x 97/16
SDAF 3152 KA x 97/16
107/16
101/2
SDAF 23156 KA x 107/16
23156 CAK/W33
517 000
750
SNP 3156 x 107/16
SDAF 3156 KA x 107/16 A 8967
ERF 973
1 250
1015/16
11
SDAF 23160 KA x 1015/16
23160 CAK/W33
634 000
670
SNP 3160 x 1015/16
SDAF 3160 KA x 1015/16 36053-157 ERF 858
1 350
1115/16
12
SDAF 23164 KA x 1115/16
23164 CAK/W33
737 000
630
SNP 3164 x 1115/16
SDAF 3164 KA x 1115/16 A 8970
ERF 900
1 850
127/16
121/2
SDAF 23168 KA x 127/16
23168 CAK/W33
827 000
600
SNP 3168 x 127/16
SDAF 3168 KA x 127/16 36053-137 ERF 975
2 450
137/16
131/2
SDAF 23172 KA x 137/16
23172 CAK/W33
842 000
560
SNP 3172 x 137/16
SDAF 3172 KA x 137/16 36053-167 ERF 872
2 500
1315/16
14
SDAF 23176 KA x 1315/16
23176 CAK/W33
841 000
400
SNP 3176 x 1315/16
SDAF 3176 KA x 1315/16 36053-143 ERF 875
2 500
1415/16
15
SDAF 23180 KA x 1415/16 23180 CAK/W33
917 000
380
SNP 3180 x 1415/16
SDAF 3180 KA x 1415/16 36053-150 ERF 882
2 800
153/4
SDAF 23184 KA x 153/4
23184 CAK/W33
1 100 000
360
SNP 3184 x 153/4
SDAF 3184 KA x 153/4
36053-160 ERF 907
4 300
161/2
SDAF 23188 KA x 161/2
23188 CAK/W33
1 170 000
340
SNP 3188 x 161/2
SDAF 3188 KA x 161/2
36053-165 ERF 958
4 300
17
SDAF 23192 KA x 17
23192 CAK/W33
1 270 000
320
SNP 3192 x 17
SDAF 3192 KA x 17
36053-154 ERF 838
5 000
18
SDAF 23196 KA x 18
23196 CAK/W33
1 370 000
300
SNP 3196 x 18
SDAF 3196 KA x 18
36053-159 ERF 888
5 300
*SKF will evaluate optional shaft diameters upon request

418
36053-114 ERF 891
1 050

SDAF 23100 KA
Custom manufactured
How to order
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23152 KA x 97/16
101/4
35
131/8
33/4
301/2
29
293/4
83/4
207/8
31/8
133/4
(4)-15/8
45/8
171/2
SDAF 23156 KA x 107/16
12
381/4
143/4
331/2
323/4
331/8
237/16
41/2
151/2
(4)-15/8
425/32
19
SDAF 23160 KA x 1015/16
12
381/4
143/4
331/2
323/4
331/8
237/16
37/8
151/2
(4)-15/8
51/8
19
SDAF 23164 KA x 1115/16
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
41/16
163/4
(4)-17/8
517/32
203/4
SDAF 23168 KA x 127/16
14
433/4
173/4
381/4
363/4
371/2
103/4
277/8
45/8
183/4
(4)-2
529/32
221/2
SDAF 23172 KA x 137/16
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
45/8
175/8
(4)-2
531/32
213/4
SDAF 23176 KA x 1315/16
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
49/32
175/8
(4)-2
61/8
213/4
SDAF 23180 KA x 15
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
413/16
191/4
(4)-21/4
613/32
24
SDAF 23184 KA x 153/4
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
519/32
213/4
(4)-21/4
67/8
261/2
SDAF 23188 KA x 161/2
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
55/16
213/4
(4)-21/4
77/32
261/2
SDAF 23192 KA x 17
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
57/16
221/4
(4)-21/2
71/2
27
SDAF 23196 KA x 18
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
53/16
221/4
(4)-21/2
721/32
27
419

SDAF 23200
Custom manufactured
How to order
information.
Shaft
Designations
dia.
Complete
pillow block
Bearing
S-3
Bearing
basic load
rating
dynamic
C
ERF
grease
speed
limit
lbs
r/min
Locknut
Lockplate
Mass
Pillow
block
housing
Stab.
ring
Triple ring
seal
S-2 shaft
(1 reqd)
da
S-2
mm
in
240
101/2
93/16
SDAF 23248
23248 CA/W33
569 000
670
N 048
PL 48
SDAF 3248
36053-114
ERF 840
ERF 923
1 100
260
111/2
915/16
SDAF 23252
23252 CA/W33
634 000
630
N 052
PL 52
SDAF 3252
A 8968
ERF 832
ERF 845
1 350
280
121/2
103/4
SDAF 23256
23256 CA/W33
634 000
600
N 056
PL 56
SDAF 3256
36053-157
ERF 866
ERF 826
1 400
300
13
111/2
SDAF 23260
23260 CA/W33
621 000
530
N 060
PL 60
SDAF 3260
36053-130
ERF 846
ERF 856
1 900
320
14
121/4
SDAF 23264
23264 CA/W33
866 000
500
N 064
PL 64
SDAF 3264
36053-137
ERF 876
ERF 983
2 500
340
15
13
SDAF 23268
23268 CA/W33
1 050 000
430
N 068
PL 68
SDAF 3268
36053-143
ERF 847
ERF 846
2 650
360
16
133/4
SDAF 23272
23272 CA/W33
1 050 000
400
N 072
PL 72
SDAF 3272
36053-150
ERF 965
ERF 981
2 950
380
17
141/2
SDAF 23276
23276 CA/W33
1 140 000
380
N 076
PL 76
SDAF 3276
36053-152
ERF 838
ERF 984
3 050
400
171/2
151/4
SDAF 23280
23280 CA/W33
1 290 000
340
N 080
PL 80
SDAF 3280
36053-165
ERF 967
ERF 895
4 500
420
181/2
153/4
SDAF 23284
23284 CA/W33
1 420 000
320
N 084
PL 84
SDAF 3284
36053-154
ERF 978
ERF 907
5 000
440
191/2
17
SDAF 23288
23288 CA/W33
1 510 000
320
N 088
PL 88
SDAF 3288
36053-159
ERF 926
ERF 838
5 050

420
(2 reqd)
S-3 shaft
(1 reqd)
lbs

SDAF 23200
Custom manufactured
How to order
customized bearing solutions and should
be reviewed by our application engineers.
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23248
101/4
35
131/8
33/4
301/2
29
293/4
83/4
207/8
39/32
133/4
(4)-15/8
47/8
171/2
SDAF 23252
12
381/4
143/4
331/2
323/4
331/8
237/16
43/8
151/2
(4)-15/8
57/32
19
SDAF 23256
12
381/4
143/4
331/2
323/4
331/8
237/16
151/2
(4)-15/8
511/32
19
SDAF 23260
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
43/32
163/4
(4)-17/8
53/4
203/4
SDAF 23264
14
433/4
173/4
381/4
363/4
371/2
103/4
277/8
43/4
183/4
(4)-2
65/32
221/2
SDAF 23268
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
417/32
175/8
(4)-2
619/32
213/4
SDAF 23272
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
51/8
191/4
(4)-21/4
63/4
24
SDAF 23276
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
49/16
191/4
(4)-21/4
71/32
24
SDAF 23280
17
53
21
51/2
461/8
443/8
451/4
141/2
333/4
55/8
213/4
(4)-21/4
71/2
261/2
SDAF 23284
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
525/32
221/4
(4)-21/2
713/16
27
SDAF 23288
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
51/4
221/4
(4)-21/2
89/32
27
421

SDAF 23200 KA
Custom manufactured
How to order
information.
Shaft dia.
S-1
Standard
Designations
Complete
pillow block
Bearing
Optional 1)
in
Bearing
basic load
rating
dynamic
C
ERF
grease
speed
limit
lbs
r/min
Adapter
assembly
Mass
Pillow
block
housing
Stab.
ring
(2 reqd)
Triple ring
seal
(2 reqd)
lbs
815/16
SDAF 23248 KA x 815/16
23248 CAK/W33
569 000
670
SNP 148 x 815/16
SDAF 3248 KA x 815/16
36053-114 ERF 914
1 100
97/16
91/2
SDAF 23252 KA x 97/16
23252 CAK/W33
634 000
630
SNP 152 x 97/16
SDAF 3252 KA x 97/16
A 8968
ERF 891
1 350
107/16
101/2
SDAF 23256 KA x 107/16
23256 CAK/W33
634 000
600
SNP 3256 x 107/16
SDAF 3256 KA x 107/16
36053-157 ERF 973
1 400
1015/16
11
SDAF 23260 KA x 1015/16 23260 CAK/W33
621 000
530
SNP 3260 x 1015/16 SDAF 3260 KA x 1015/16 36053-130 ERF 1002
1 900
1115/16
12
SDAF 23264 KA x 1115/16 23264 CAK/W33
866 000
500
SNP 3264 x 1115/16 SDAF 3264 KA x 1115/16 36053-137 ERF 900
2 500
127/16
121/2
SDAF 23268 KA x 127/16
23268 CAK/W33
1 050 000
430
SNP 3268 x 127/16
SDAF 3268 KA x 127/16
36053-143 ERF 975
2 650
137/16
131/2
SDAF 23272 KA x 137/16
23272 CAK/W33
1 050 000
400
SNP 3272 x 137/16
SDAF 3272 KA x 137/16
36053-150 ERF 979
2 950
1315/16
14
SDAF 23276 KA x 1315/16 23276 CAK/W33
1 140 000
380
SNP 3276 x 1315/16 SDAF 3276 KA x 1315/16 36053-152 ERF 977
3 050
1415/16
15
SDAF 23280 KA x 15
23280 CAK/W33
1 290 000
340
SNP 3280 x 15
SDAF 3280 KA x 15
36053-165 ERF 976
4 500
153/4
SDAF 23284 KA x 153/4
23284 CAK/W33
1 420 000
320
SNP 3284 x 153/4
SDAF 3284 KA x 153/4
36053-154 ERF 907
5 000
161/2
SDAF 23288 KA x 161/2
23288 CAK/W33
1 510 000
320
SNP 3288 x 161/2
SDAF 3288 KA x 161/2
36053-159 ERF 958
5 050
*SKF will evaluate optional shaft diameters upon request

1) Requires different adapter sleeve and seals.

422

SDAF 23200 KA
Custom manufactured
How to order
information.
Designations
Complete
pillow block
A
E
Max
E
Min
E
Drilled
holes
Static
oil
level
K
Bolts
(No. reqd)
in
SDAF 23248 KA x 815/16
101/4
35
131/8
33/4
301/2
29
293/4
83/4
207/8
39/32
133/4
(4)-15/8
47/8
171/2
SDAF 23252 KA x 97/16
12
381/4
143/4
331/2
323/4
331/8
237/16
43/8
151/2
(4)-15/8
57/32
19
SDAF 23256 KA x 107/16
12
381/4
143/4
331/2
323/4
331/8
237/16
151/2
(4)-15/8
511/32
19
SDAF 23260 KA x 1015/16
1213/16
413/4
153/4
41/2
361/2
35
353/4
101/2
253/4
43/32
163/4
(4)-17/8
53/4
203/4
SDAF 23264 KA x 1115/16
14
433/4
173/4
381/4
363/4
371/2
103/4
277/8
43/4
183/4
(4)-2
65/32
221/2
SDAF 23268 KA x 127/16
141/2
46
171/8
51/4
403/4
391/4
40
11
287/8
417/32
175/8
(4)-2
619/32
213/4
SDAF 23272 KA x 137/16
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
51/8
191/4
(4)-21/4
63/4
24
SDAF 23276 KA x 1315/16
151/2
483/4
183/4
51/2
431/2
413/4
425/8
121/4
301/2
49/16
191/4
(4)-21/4
71/32
24
SDAF 23280 KA x 15
17
52
21
51/2
461/8
443/8
451/4
141/2
333/4
55/8
213/4
(4)-21/4
71/2
261/2
SDAF 23284 KA x 153/4
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
525/32
221/4
(4)-21/2
713/16
27
SDAF 23288 KA x 161/2
18
541/4
215/8
53/4
487/8
471/8
48
15
353/4
51/4
221/4
(4)-21/2
89/32
27
423
Accessories (inch series)

Mounting accessories / introduction
Adapters
The adapter is used to hold and locate a
tapered bore bearing on a cylindrical shaft
seat. It permits relatively wide tolerances for
the shaft diameter and makes it unnecessary
to heat the bearing or use a press when
mounting in order to obtain an interference
fit of the inner ring on the shaft.
SKF adapters are manufactured with the
same precise techniques and care used in
the manufacture of bearings.
SKF adapters are generally supplied
complete with locknut and locking device.
Hydraulic assist adapters

(OSNW and OSNP)
SKF inch adapter sleeves for bearing sizes 26
(22226, 23226) and larger, can be supplied
with oil supply ducts and distribution grooves
for pressurized oil to assist in mounting and
dismounting. M6 x 1 threads are used for
all inch dimension adapter sleeves. For
corresponding information on inch dimension
adapter sleeves, please consult SKF Applications
Engineering.
Dimensions and
tolerances
The adapters, locknuts, lockwashers,
lockplates and withdrawal sleeves generally
conform to ABMA standard 8.2.
In addition to the inch bore accessories
shown in these catalog tables the SKF
manufacturing program includes metric bore
adapter sleeves and withdrawal sleeves along
with their associated locking devices. Consult
SKF for information.
Hydraulic assist adapters (nomenclature):

OS....
Inlet on non-threaded side to distribution groove on tapered surface
OS....H
Inlet on threaded side to distribution groove on tapered surface
OS....HB
Inlet on threaded side to distribution groove on tapered surface;

2nd inlet on threaded side to distribution groove on bore surface
OS....B
Inlet on non-threaded side to distribution groove on tapered surface;

2nd inlet on non-threaded side to distribution groove on bore surface
Complete adapters
424
Mounting accessories / nomenclature
Complete adapters
SN W 32
1. Adapters:
S
Adapter sleeve
Locknut
2. Locking device:
3
2
Lockwasher
Lockplate
3. Size:
Locknuts
AN 26
1
Lockwashers / lockplates
W 30
1
1. Locknut:
N
Heavy section
AN
Heavy section
NO
Light section
2. Size:
1. Locking device:
W
Lockwasher, heavy section
WO
Lockwasher, light section
PL
Lockplate
2. Size:
425

Adapters
Bearings series 12, 13, 222
How to order
Specify
Complete adapter
Shaft size
SNW 5
x 3/4
All mounting accessories are manufactured in accordance with ABMA standard 8.2 latest revision. For more information on threads please consult this standard.
Consult SKF for optional shaft sizes.
Bearing
size
Shaft dia.
da
Standard
Complete
adapter
Designations
Locknut
Lockwasher
Mass
Adapter
sleeve
Optional
in
3
4
16
1316
1516
1716
138, 112
5
6
7
8
9
N
N
N
N
N
05
06
07
08
09
W 05
W 06
W 07
W 08
W 09
10
11
12
13
14
11116
11516
2116
2316
2516
158, 134
178, 2
218, 214
SNW
SNW
SNW
SNW
SNW
10
11
12
13
14
N
N
N
N
N
10
11
12
13
14
W 10
W 11
W 12
W 13
W 14
15
16
17
18
19
2716
21116
21516
3316
3516
238, 212
258, 234
21316, 278, 3
3116, 318, 314
SNW
SNW
SNW
SNW
SNW
15
16
17
18
19
AN
AN
AN
AN
AN
15
16
17
18
19
20
21
22
24
26
3716
31116
31516
4316
4716
3516, 338, 312
31316, 378, 4
4116, 418, 414
4516, 438, 412
SNW
SNW
SNW
SNW
SNW
20
21
22
24
26
AN
AN
AN
AN
AN
28
30
32
34
36
41516
5316
5716
51516
6716
41316, 478, 5
518, 514
538, 512
51316, 578, 6
6516, 638, 612
SNW
SNW
SNW
SNW
SNW
28
30
32
34
36
AN
AN
AN
AN
AN
38
40
44
61516
7316
71516
61316, 678, 7
718, 714
71316, 778, 8
SNW 38
SNW 40
SNW 44
SNW
SNW
SNW
SNW
SNW
5
6
7
8
9
0.22
0.28
0.35
0.41
0.62
1.269
1.353
1.459
1.504
1.584
0.562
0.622
0.654
0.662
0.662
0.9470
1.1339
1.3369
1.5237
1.7277
32
18
18
18
18
S
S
S
S
S
10
11
12
13
14
0.73
0.80
1.10
1.40
1.80
1.765
1.845
1.989
2.100
2.274
0.724
0.729
0.760
0.792
0.792
1.9277
2.1174
2.3204
2.5084
2.7114
18
18
18
18
18
W 15
W 16
W 17
W 18
W 19
S
S
S
S
S
15
16
17
18
19
2.25
2.40
2.90
3.05
4.05
2.296
2.376
2.486
2.646
2.760
0.895
0.895
0.926
1.010
1.041
2.8752
3.0790
3.2812
3.4682
3.6712
12
12
12
12
12
20
21
22
24
26
W 20
W 21
W 22
W 24
W 26
S
S
S
S
S
20
21
22
24
26
4.40
4.55
5.00
6.65
9.70
2.869
2.987
3.206
3.466
3.762
1.073
1.073
1.135
1.166
1.229
3.8592
4.0618
4.2648
4.6558
5.0458
12
12
12
12
12
28
30
32
34
36
W 28
W 30
W 32
W 34
W 36
S
S
S
S
S
28
30
32
34
36
10.5
16.0
15.5
19.5
20.5
3.981
4.241
4.578
4.847
5.038
1.291
1.354
1.510
1.541
1.573
5.4368
5.8278
6.1953
6.5703
6.9773
12
12
8
8
8
AN 38
AN 40
N 44
W 38
W 40
W 44
S 38
S 40
S 44
23.5
30.5
32.5
5.261
5.484
5.901
1.604
1.666
1.698
7.3833
7.7571
8.5378
8
8
8
426
Threads
per
inch
lbs
05
06
07
08
09
15
B1
Dimensions
Mean thread
pitch
diameter
d2
S
S
S
S
S
Adapters
Bearings series 230
How to order
Specify
Complete adapter
Shaft size
SNW 3024
x 43/16
Bearing
size
Shaft dia.
da
Standard
Complete
adapter
Designations
Locknut
Lockwasher
Mass
Adapter
sleeve
Optional
B1
in
Dimensions
Mean thread
pitch
diameter
d2
Threads
per
inch
lbs
24
26
28
30
32
4316
4716
41516
5316
5716
4116, 418, 414

4516, 438, 412
41316, 478, 5
518, 514
538, 512
SNW
SNW
SNW
SNW
SNW
3024
3026
3028
3030
3032
N
N
N
N
N
024
026
028
030
032
W 024
W 026
W 028
W 030
W 032
S
S
S
S
S
3024
3026
3028
3030
3032
6.15
7.50
8.45
9.80
12.0
2.947
3.237
3.340
3.492
3.711
1.250
1.313
1.375
1.406
1.468
4.6558
5.0458
5.4368
5.8278
6.1953
12
12
12
12
8
34
36
38
40
44
51516
6716
61516
7316
71516
51316, 578, 6
6516, 638, 612
61316, 678, 7
718, 714
71316, 778, 8
SNW
SNW
SNW
SNW
SNW
3034
3036
3038
3040
3044
N
N
N
N
N
034
036
038
040
044
W 034
W 036
W 038
W 040
W 044
S
S
S
S
S
3034
3036
3038
3040
3044
13.5
15.0
16.5
19.5
24.5
4.019
4.337
4.412
4.750
5.130
1.500
1.531
1.594
4.656
1.750
6.5703
6.9773
7.3833
7.7571
8.5378
8
8
8
8
8
48
52
56
60
64
81516
9716
10716
101516
111516
8716, 812, 9
912
10, 1012
11
1112, 12
SNP
SNP
SNP
SNP
SNP
3048
3052
3056
3060
3064
N
N
N
N
N
048
052
056
060
064
PL
PL
PL
PL
PL
48
52
56
60
64
S
S
S
S
S
3048
3052
3056
3060
3064
32.0
41.0
45.5
59.0
65.0
5.432
6.019
6.191
6.727
6.946
1.968
2.125
2.219
2.281
2.375
9.3245
10.0742
10.8852
11.6662
12.4440
6
6
6
6
6
68
72
76
80
84
12716
13716
131516
15
1534
1212
13, 1312
14
15
SNP
SNP
SNP
SNP
SNP
3068
3072
3076
3080
3084
N
N
N
N
N
068
072
076
080
084
PL
PL
PL
PL
PL
68
72
76
80
84
S
S
S
S
S
3068
3072
3076
3080
3084
78.0
86.0
94.5
100.0
105.0
7.543
7.579
7.743
8.411
8.498
2.531
2.531
2.656
2.813
2.813
13.1910
14.0220
14.8090
15.5970
16.3840
5
5
5
5
5
1612
17
18
1812
1912
SNP 3088
SNP 3092
SNP 3096
SNP 30/500
SNP 30/530
N
N
N
N
N
088
092
096
500
530
S 3088
S 3092
S 3096
S 32/500
S 32/530
130.0
157.0
165.0
200.0
263.0
9.100
9.336
9.446
9.838
10.679
3.228
3.228
3.260
3.573
3.573
17.2830
18.0710
18.8580
19.6460
20.8270
5
5
5
5
4
88
92
96
500
530
PL 88
PL 92
PL 96
PL 500
PL 530
427

Adapters
Bearings series 231
How to order
Specify
Complete adapter
Shaft size
SNW 3122
x 315/16
Bearing
size
Shaft dia.
da
Standard
Complete
adapter
Designations
Locknut
Lockwasher
Mass
Adapter
sleeve
Optional
B1
in
Dimensions
Mean thread
pitch
diameter
d2
Threads
per
inch
lbs
22
24
26
28
30
31516
414
4716
41516
5316
SNW
SNW
SNW
SNW
SNW
3122
3124
3126
3128
3130
N
N
N
N
N
022
024
026
028
030
W 022
W 024
W 026
W 028
W 030
S
S
S
S
S
22
24
26
28
30
4.25
5.85
8.35
8.85
13.5
3.206
3.466
3.762
3.981
4.241
1.135
1.166
1.229
1.291
1.354
4.2648
4.6558
5.0458
5.4368
5.8278
12
12
12
12
12
32
34
36
38
40
5716
51516
6716
61516
7316
SNW
SNW
SNW
SNW
SNW
3132
3134
3136
3138
3140
N
N
N
N
N
032
034
036
038
040
W 032
W 034
W 036
W 038
W 040
S
S
S
S
S
32
34
36
38
40
13.5
16.0
17.0
19.5
28.5
4.578
4.847
5.038
5.261
5.484
1.510
1.541
1.573
1.604
1.666
6.1953
6.5703
6.9773
7.3833
7.7571
8
8
8
8
8
44
48
52
56
60
71516
81516
9716
10
101516
912
1012
11
SNW 3144
SNP 3148
SNP 3152
SNP 3156
SNP 3160
N
N
N
N
N
044
048
052
056
060
W 044
PL 48
PL 52
PL 56
PL 60
S 44
S 48
S 52
S 3156
S 3160
28.0
37.5
44.0
46.5
59.5
5.901
6.638
7.593
7.766
8.830
1.698
1.979
2.125
2.219
2.281
8.5378
9.3245
10.0742
10.8852
11.6662
8
6
6
6
6
64
68
72
76
80
12
12716
13716
131516
15
12
1212
1312
14
15
SNP
SNP
SNP
SNP
SNP
3164
3168
3172
3176
3180
N
N
N
N
N
064
068
072
076
080
PL
PL
PL
PL
PL
64
68
72
76
80
S
S
S
S
S
3164
3168
3172
3176
3180
74.0
93.5
120.0
125.0
140.0
9.111
9.787
9.862
10.066
10.459
2.375
2.531
2.531
2.656
2.875
12.4440
13.1910
14.0220
14.8090
15.5970
6
5
5
5
5
84
88
92
96
1534
1612
17
18
SNP
SNP
SNP
SNP
3184
3188
3192
3196
N
N
N
N
084
088
092
096
PL
PL
PL
PL
84
88
92
96
S
S
S
S
3184
3188
3192
3196
145.0
151.0
209.0
201.0
11.412
11.817
12.368
12.714
2.938
3.228
3.323
3.354
16.3840
17.2830
18.0710
18.8580
5
5
5
5
428
Adapters
Bearings series 223 and 232
da 17/16 - 53/16 in
Bearing
size
Shaft dia.
da
Standard
Complete
adapter
Designations
Locknut Lockwasher
Mass
Adapter
sleeve
in
B1
Dimensions
Mean thread
pitch
diameter
d2
Threads
per
inch
lbs
09
10
11
12
13
1716
11116
11516
2116
2316
SNW
SNW
SNW
SNW
SNW
109
110
111
112
113
N
N
N
N
N
09
10
11
12
13
W 09
W 10
W 11
W 12
W 13
S
S
S
S
S
109
110
111
112
113
0.71
0.87
0.94
1.60
1.75
2.133
2.394
2.516
2.659
2.771
0.622
0.724
0.729
0.760
0.792
1.7277
1.9277
2.1174
2.3204
2.5084
18
18
18
18
18
14
15
16
17
18
2716
278
21116
21516
3316
SNW
SNW
SNW
SNW
SNW
114
115
116
117
118
N 14
AN 15
AN 16
AN 17
AN 18
W 14
W 15
W 16
W 17
W 18
S
S
S
S
S
114
115
116
117
118
2.05
2.95
3.20
3.40
4.00
2.945
3.084
3.204
3.312
3.553
0.792
0.895
0.895
0.926
1.010
2.7114
2.8752
3.0790
3.2812
3.4682
18
12
12
12
12
19
20
22
24
26
3516
3716
31516
4316
4716
SNW
SNW
SNW
SNW
SNW
119
120
122
124
126
AN
AN
AN
AN
AN
19
20
22
24
26
W 19
W 20
W 22
W 24
W 26
S
S
S
S
S
119
120
122
124
126
4.80
6.25
6.45
7.80
12.5
3.702
3.971
4.348
4.648
4.982
1.041
1.073
1.135
1.166
1.229
3.6712
3.8592
4.2648
4.6558
5.0458
12
12
12
12
12
28
30
41516
5316
SNW 128
SNW 130
AN 28
AN 30
W 28
W 30
S 128
S 130
13.0
8.15
5.323
5.621
1.291
1.354
5.4368
5.8278
12
12
429

Adapters
Bearings series 223 and 232
da 57/16 - 161/2 in
How to order
Specify
Complete adapter
Shaft size
SNW 132
x 57/16
Bearing
size
Shaft dia.
da
Standard
Complete
adapter
Designations
Locknut
Lockwasher/
lockplate
Mass
Adapter
sleeve
Optional
B1
in
32
34
36
38
40
5716
51516
6716
61516
7316
44
48
52
56
60
Threads
per
inch
lbs
538, 512
51316, 578, 6
61316, 678, 7
718, 714
SNW
SNW
SNW
SNW
SNW
71516
81516
9716
10716
101516
912
1012
11
64
68
72
76
80
111516
12716
13716
131516
15
84
88
1534
1612
132
134
136
138
140
32
34
36
38
40
W 32
W 34
W 36
W 38
W 40
SNW 144
SNP 148
SNP 152
SNP 3256
SNP 3260
AN 44
N 048
N 052
N 056
N 060
12
1212
1312
14
15
SNP
SNP
SNP
SNP
SNP
N
N
N
N
N
SNP 3284
SNP 3288
3264
3268
3272
3276
3280
430
Dimensions
Mean thread
pitch
diameter
d2
AN
AN
AN
AN
AN
064
068
072
076
080
N 084
N 088
132
134
136
138
140
18.0
21.0
22.5
28.0
35.5
5.920
6.188
6.456
6.758
7.095
1.510
1.541
1.573
1.604
1.666
6.1953
6.5703
6.9773
7.3833
7.7571
8
8
8
8
8
W 44
PL 48
PL 52
PL 56
PL 60
S 144
S 148
S 152
S 3256
S 3260
46.5
48.5
54.5
59.0
68.5
7.287
8.109
8.774
8.947
9.640
1.698
1.979
2.125
2.219
2.281
8.5378
9.3245
10.0742
10.8852
11.6662
8
6
6
6
6
PL
PL
PL
PL
PL
S
S
S
S
S
3264
3268
3272
3276
3280
98.0
105.0
135.0
145.0
165.0
10.371
11.126
11.437
11.877
12.664
2.375
2.531
2.531
2.656
2.875
12.4440
13.1910
14.0220
14.8090
15.5970
6
5
5
5
5
S 3284
S 3288
165.0
190.0
13.302
13.943
2.938
3.228
16.3840
17.2830
5
5
64
68
72
76
80
PL 84
PL 88
S
S
S
S
S
Mounting accessories / locknuts lockwashers and lockplates
Locknuts, lockwashers
and lockplates
Dimensions and
tolerances
Locknuts and lockwashers are commonly

used as effective means for holding bearing
inner rings axially on the shaft. They are also
frequently used to secure gears, belt pulleys
and other machine components. The
locknuts are accurately made to insure that
the abutment face will be square with the
shaft axis, thus avoiding distortion of the
shaft during tightening.
The lockwashers are made from
selected high quality steel, heat treated,
and they must pass a final inspection that
requires their surfaces to be smooth and
free from burrs.
The lockplate is a steel stamping that
engages the slot of the sleeve and is secured
to the end face of larger nuts by two screws.
This unit is used in lieu of lockwashers.
Wherever bearings must be held in
permanent or correct position, SKF locknuts,
lockwashers and lockplates are recommended.
The adapters, locknuts, lockwashers, lockplates

and withdrawal sleeves generally conform to
ABMA standard 8.2.
In addition to the inch bore accessories
shown in these catalog tables, the SKF
manufacturing program includes metric bore
adapter sleeves and withdrawal sleeves along
with their associated locking devices. Consult
SKF for information.
Locknuts
Lockwashers / Lockplates
431

Heavy section
Locknuts and lockwashers
Bearing Series 12, 13, 222, 223, 232
How to order
Specify
N 00
W 00
Locknut
Lockwasher
For recommended bearing seat tolerances see page 351.
Bearing
size
Designations
Locknut
Lockwasher
Combined
mass
d
in
00
01
02
03
04
N
N
N
N
N
00
01
02
03
04
W
W
W
W
W
00
01
02
03
04
0.02
0.04
0.05
0.07
0.11
0.3937
0.4724
0.5906
0.6693
0.7874
0.3910
0.4690
0.5860
0.6640
0.7810
0.3856
0.4636
0.5806
0.6586
0.7756
05
06
07
08
09
N
N
N
N
N
05
06
07
08
09
W
W
W
W
W
05
06
07
08
09
0.14
0.16
0.24
0.27
0.34
0.9843
1.1811
1.3780
1.5748
1.7717
0.9690
1.1730
1.3760
1.5630
1.7670
0.9636
1.1648
1.3678
1.5548
1.7588
10
11
12
13
14
N
N
N
N
N
10
11
12
13
14
W
W
W
W
W
10
11
12
13
14
0.39
0.48
0.54
0.64
0.73
1.9685
2.1654
2.3622
2.5591
2.7559
1.9670
2.1570
2.3600
2.5480
2.7510
1.9588
2.1488
2.3518
2.5398
2.7428
15
16
17
18
19
AN
AN
AN
AN
AN
15
16
17
18
19
W
W
W
W
W
15
16
17
18
19
0.90
1.05
1.20
1.50
1.75
2.9528
3.1496
3.3465
3.5433
3.7402
2.9330
3.1370
3.3400
3.5270
3.7300
2.9218
3.1258
3.3288
3.5158
3.7188
20
AN 20
W 20
2.05
3.9370
3.9180
3.9068
432
lbs
Shaft dimensions
Threads major dia.
d3
max
min.
Heavy section
Bearing series 12, 13, 222, 223, 232
How to order
Specify
N 00
W 00
Locknut
Lockwasher
Thread pitch dia.

d2
max
min
Threads
per
inch
d1
max
C
+164
0
Dimensions
G
I
+132
+164
0
0
E
+164
0
F
+164
0
16
16
1
16
1
16
1
16
8
8
1
8
1
8
3
16
Locknut
Lockwasher
D1
d4
32
16
5
16
11
32
3
8
0.042
0.042
0.042
0.042
0.042
0.414
0.492
0.609
0.687
0.809
13
in
5
0.3707
0.4487
0.5657
0.6437
0.7607
0.3681
0.4461
0.5627
0.6407
0.7573
32
32
32
32
32
16
32
1
2
9
16
23
32
0.9487
1.1369
1.3399
1.5269
1.7309
0.9453
1.1329
1.3359
1.5224
1.7204
32
18
18
18
18
7
8
1116
114
11532
11116
1.9309
2.1209
2.3239
2.5119
2.7149
1.9264
2.1158
2.3188
2.5068
2.7098
18
18
18
18
18
2.8789
3.0829
3.2859
3.4729
3.6759
2.8735
3.0770
3.2800
3.4655
3.6685
3.8639
3.8565
32
8
3
8
13
32
7
16
8
32
15
32
1
2
17
32
15
32
32
1
2
17
32
17
32
19
32
32
5
8
21
32
11
16
1
3
16
16
3
16
5
16
5
16
19
16
32
3
32
3
32
1
8
15
32
32
3
32
3
32
3
32
1916
134
2116
214
21732
32
32
7
16
7
16
7
16
0.050
0.050
0.050
0.058
0.058
0.999
1.203
1.406
1.593
1.805
178
2116
214
2716
258
19
32
32
5
8
21
32
21
32
4
4
25
32
13
16
29
32
32
8
1
8
1
8
1
8
1
21116
23132
3532
338
358
16
16
5
16
5
16
5
16
8
8
1
8
1
8
1
8
19
2
2
17
32
9
16
9
16
0.058
0.063
0.063
0.063
0.063
2.005
2.195
2.413
2.601
2.804
12
12
12
12
12
22532
3
3316
338
3916
11
16
16
23
32
13
16
27
32
15
16
16
31
32
1116
1332
32
32
5
32
5
32
5
32
5
3
8
8
1
8
5
32
5
32
1
378
4532
41332
42132
41516
19
16
8
3
8
3
8
3
8
15
32
32
5
8
11
16
23
32
0.072
0.072
0.072
0.094
0.094
2.988
3.192
3.410
3.597
3.815
12
32532
1316
5316
0.094
4.003
13
11
15
32
16
16
5
64
5
64
5
64
32
4
8
1
118
138
13
19
433

Heavy section
Bearing series 12, 13, 222, 223, 232*
How to order
Specify
AN 21
W 21
Locknut
Lockwasher
Bearing
size
Designations
Locknut
Lockwasher
Combined
mass
d
lbs
Shaft dimensions
Threads major dia.
d3
max
min
in
21
22
24
26
28
AN
AN
AN
AN
AN
21
22
24
26
28
W
W
W
W
W
21
22
24
26
28
2.25
2.45
2.80
3.90
4.30
4.1339
4.3307
4.7244
5.1181
5.5118
4.122
4.325
4.716
5.106
5.497
4.1108
4.3138
4.7048
5.0948
5.4858
30
32
34
36
38
AN
AN
AN
AN
AN
30
32
34
36
38
W
W
W
W
W
30
32
34
36
38
5.40
6.15
7.55
8.25
8.80
5.9055
6.2992
6.6929
7.0866
7.4803
5.888
6.284
6.659
7.066
7.472
5.8768
6.2688
6.6438
7.0508
7.4568
40
44
AN 40
N 44
W 40
W 44
9.70
13.50
7.8740
8.6614
7.847
8.628
7.8318
8.6128
*For bearings in series 232, larger than a 23244, use locknuts and lockplates on pages 436 and 437.
434
Heavy section
Bearing series 12, 13, 222, 223, 232*
How to order
Specify
AN 21
W 21
Locknut
Lockwasher
Thread pitch dia.

d2
max
min
Threads
per
inch
d1
max
C
+116
0
Dimensions
G
I
+132
+116
0
0
E
+116
0
F
+164
0
Locknut
D1
Lockwasher
L
d4
4
32
13
16
7
8
15
16
0.094
0.125
0.125
0.125
0.125
4.207
4.410
4.816
5.209
5.600
in
4.0679
4.2709
4.6619
5.0519
5.4429
4.0596
4.2626
4.6536
5.0436
5.4346
12
12
12
12
12
31516
4316
4916
41516
5516
8
32
15
16
1
1116
1316
1732
114
1516
138
32
32
5
32
5
32
5
32
8
8
3
8
1
2
5
8
32
16
3
16
3
16
3
16
5716
52332
618
634
7332
5.8339
6.2028
6.5778
6.9848
7.3908
5.8256
6.1937
6.5687
6.9757
7.3817
12
8
8
8
8
534
618
612
62932
7516
118
1316
1732
114
1932
112
1916
11932
158
12132
32
4
1
4
1
4
1
4
8
8
3
4
3
4
3
4
15
32
64
15
64
15
64
15
64
71116
8116
82132
9116
91532
31
32
1132
1116
1332
118
0.156
0.156
0.156
0.156
0.156
6.001
6.407
6.782
7.189
7.595
7.7658
8.5468
7.7544
8.5347
8
8
71116
8516
11132
138
12332
1916
15
92732
11
1316
114
0.156
0.156
8.000
8.719
29
4
4
8
1 16
64
8
25
*For bearings in series 232, larger than a 23244, use locknuts and lockplates on pages 436 and 437.
435

Light section
Locknuts, lockwashers and lockplates
Bearing series 230, 231, 23248 and larger
How to order
Specify
N 022
W 022
Locknut
Lockwasher
Bearing
size
Designations
Locknut
Lockwasher
Combined
mass
Shaft dimensions
Threads major dia.
d3
max
min
lbs
22
24
26
28
30
N
N
N
N
N
022
024
026
028
030
W
W
W
W
W
022
024
026
028
030
1.75
1.90
2.65
2.60
3.65
4.3307
4.7244
5.1181
5.5118
5.9055
4.325
4.716
5.106
5.497
5.888
4.3138
4.7048
5.0948
5.4858
5.8768
32
34
36
38
40
N
N
N
N
N
032
034
036
038
040
W
W
W
W
W
032
034
036
038
040
4.15
4.50
4.80
6.65
7.65
6.2992
6.6929
7.0866
7.4803
7.8740
6.284
6.659
7.066
7.472
7.847
6.2688
6.6438
7.0508
7.4568
7.8318
44
N 044
W 044
9.25
8.6614
8.628
8.6128
48
52
56
60
64
N
N
N
N
N
048
052
056
060
064
PL
PL
PL
PL
PL
48
52
56
60
64
13.0
15.0
17.0
23.0
26.0
9.4488
10.2362
11.0236
11.8110
12.5984
9.442
10.192
11.004
11.785
12.562
9.4218
10.1718
10.9838
11.7648
12.5418
68
72
76
80
84
N
N
N
N
N
068
072
076
080
084
PL
PL
PL
PL
PL
68
72
76
80
84
29.5
30.0
41.0
46.0
49.0
13.3858
14.1732
14.9606
15.7480
16.5354
13.303
14.134
14.921
15.709
16.496
13.2870
14.1180
14.9050
15.6930
16.4800
88
92
96
1500
1530
N
N
N
N
N
088
092
096
500
530
PL 88
PL 92
PL 96
PL 500
PL 530
66.5
68.5
71.5
79.0
107.0
17.3228
18.1102
18.8976
19.6460
20.8270
17.283
18.071
18.858
19.646
20.827
17.2670
18.0550
18.8420
19.6440
20.8070
(B+L+1/4 for N 048-N 076)
436
in
Light section
Locknuts, lockwashers and lockplates
Bearing series 230, 231, 23248 and larger
Lockplate and capscrew
How to order
Specify
N 022
W 022
Locknut
Lockwasher
Thread pitch dia.

d2
max
min
Threads
per
inch
d1
max
C
+164
0
Dimensions
G
I
+132
+164
0
0
E
+164
0
F
+164
0
Locknut
D1
Lockwasher
L
d4
0.125
0.125
0.125
0.125
0.125
4.410
4.816
5.209
5.600
6.000
in
4.2709
4.6619
5.0519
5.4429
5.8339
4.2626
4.6536
5.0436
5.4346
5.8256
12
12
12
12
12
4316
4916
41516
5516
52332
29
1
1116
118
1732
114
1516
138
112
6.2028
6.5778
6.9848
7.3908
7.7658
6.1937
6.5687
6.9757
7.3817
7.7544
8
8
8
8
8
618
612
6932
7516
71116
1316
1732
114
1932
11132
1916
11932
158
12132
12332
8.5468
8.5347
8516
138
1916
9.3337
10.0837
10.8957
11.6767
12.4537
9.3123
10.0707
10.8827
11.6637
12.4402
6
6
6
6
6
9316
91516
1034
1112
12516
12332
12532
178
11516
2132
2
1
2
1
2
1
2
1
2
13.203
14.034
14.821
15.609
16.396
13.187
14.018
14.805
15.593
16.380
5
5
5
5
5
13116
131316
1458
1538
16316
2532
2532
2932
2716
2716
17.183
17.971
18.758
19.546
20.702
17.167
17.955
18.742
19.530
20.682
5
5
5
5
4
17
1734
1812
1914
2014
234
234
234
3964
3964
32
16
15
32
32
5
32
5
32
5
32
8
8
1
2
5
8
5
8
16
16
3
16
3
16
7
32
5516
51116
618
612
718
8
4
3
4
3
4
7
8
15
15
64
64
15
64
15
64
15
64
712
778
814
81116
9716
1132
1116
1332
118
1316
0.125
0.125
0.125
0.125
0.125
6.407
6.782
7.189
7.595
8.000
1116
1014
114
0.125
8.719
4
1
4
1
4
1
4
1
4
118
1316
114
138
1716
16
7
16
7
16
7
16
7
16
11716
12316
13
14316
15
11132
11332
112
1916
12132
2
2
1
2
1
2
1
2
4
4
1
4
1
4
1
4
16
2
1
2
1
2
1
2
1534
1612
1734
1812
19516
12532
12532
12932
2116
2116
8-16
8-16
1
2-13
1
2-13
1
2-13
x
x
x
x
x
112
112
112
158
158
2012
2114
22116
221316
241316
238
238
238
21116
21116
11316
11316
11316
1.812
1.812
x
x
x
x
x
1
1
114
114
114
2
2
1
2
1
2
1
2
4
4
1
4
1
4
1
4
1
4
4
1
4
1
4
1
4
2
2
1
2
1
2
1
2
1
25
32
16
7
8
15
16
31
32
13
Capscrew size
16-18 x 58
5
16-18 x 58
5
16-18 x 58
3
8-16 x 34
3
8-16 x 34
8-11
8-11
5
8-11
5
8-11
5
8-11
5
4
4
7
8
7
8
7
8
3
437

Withdrawal sleeves, removal nuts
Bearing series 13 and 222
Bearing
size
08
09
10
11
12
13
14
1)
15
2)
16
17
18
19
20
21
22
24
26
28
30
32
34
36
38
40
44
48
4)
Sleeve
SK 8
SK 9
SK 10
SK 11
SK 12
ASK 13
ASK 14
SK 2215
SK 2216
ASK 17
ASK 18
ASK 19
ASK 20
ASK 21
ASK 22
ASK 24
ASK 26
SK 28
SK 30
SK 32
SK 34
SK 36
SK 38
SK 40
SK 44
SK 48
Designations
Locknut Lockwasher
N
N
N
N
N
N
N
N
N
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
AN
N
07
08
09
10
11
12
12
13
14
15
16
17
18
19
20
22
22
24
26
28
30
32
34
36
40
44
Mass
Dimensions
Removal
nut
da
B1
D1
Mean thread
pitch
diameter
d2
5)
lb
in
in
in
in
W 07
W 08
W 09
W 10
W 11
W 12
W 12
W 13
W 14
W 15
W 16
W 17
W 18
W 19
W 20
W 22
W 22
W 24
W 26
W 28
W 30
W 32
W 34
W 36
W 40
W 44
N 09
N 10
RN 10
RN 11
RN 12
AN 15
AN 16
AN 17
AN 18
AN 19
AN 20
AN 21
AN 22
ARN 21
ARN 22
ARN 24
ARN 26
RN 28
RN 30
RN 32
RN 34
RN 36
RN 38
N 44
N 048
N 052
0.16
0.22
0.25
0.31
0.41
0.50
0.94
1.25
1.25
1.45
1.55
1.80
2.00
2.30
2.45
3.15
5.00
5.90
6.80
9.95
11.50
12.50
14.50
16.50
19.50
24.50
1.377
1.574
1.771
1.968
2.164
2.361
2.361
2.558
2.755
2.952
3.149
3.346
3.543
3.740
3.937
4.330
4.527
4.921
5.315
5.512
5.906
6.299
6.693
7.087
7.874
8.661
1.181
1.260
1.378
1.457
1.575
1.654
1.732
1.732
1.732
2.047
2.087
2.244
2.323
2.441
2.559
2.835
3.071
3.228
3.465
3.780
4.095
4.095
4.409
4.646
5.118
5.669
0.098
0.098
0.118
0.118
0.138
0.138
0.138
0.138
0.138
0.138
0.138
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.236
0.236
21732
21116
3932
312
32332
378
4532
41332
4
41516
5316
5716
52332
6
62532
71332
72532
81732
9 532
92532
101332
102932
1178
11
11716
12316
16
2
9
16
9
16
5
8
19
32
19
32
5
8
11
16
23
32
3
4
3
4
3
4
3
4
3
4
13
16
7
8
15
16
1
1
1116
1116
1316
114
11132
11332
1.7277
1.9277
2.1644
2.3674
2.5864
2.8752
3.0790
3.2812
3.4682
3.6712
3.8592
4.0618
4.2648
4.4988
4.7178
5.1248
5.5618
6.0083
6.4143
6.8363
7.2423
7.6643
8.1019
8.5378
9.3245
10.0742
18
18
18
18
18
12
12
12
12
12
12
12
12
12
12
12
12
8
8
8
8
8
8
8
6
6
21
32
7
1
1) For bearing 1315, use sleeve No. ASK 15 with length of 1.850.
2) For bearing 1316, use sleeve No. ASK 16 with length of 1.969.
3) Threads derived from the Screw Threads Standards for Federal Services Handbook H-28 (1944) page 111, and H-28 (1957) Part 1, page 181, Class 3.
4) Last two figures of bearing designation.
5) Stickout before the sleeve is pressed into the bearing bore.
438
3)
Threads
per
inch
Withdrawal sleeves, removal nuts

Bearing series 23 and 223
Bearing
size
08
*09
10
11
12
13
14
15
16
17
18
19
20
21
22
24
26
28
30
32
34
36
38
40
44
48
2)
Sleeve
Designations
Locknut Lockwasher
SK 108
SK 109
SK 110
SK 111
SK 112
ASK 113
ASK 114
ASK 115
ASK 116
ASK 117
ASK 118
ASK 119
ASK 120
ASK 121
ASK 122
ASK 124
ASK 126
SK 128
SK 130
SK 132
SK 134
SK 136
SK 138
SK 140
SK 144
SK 148
N 07
N 08
N 09
N 10
N 11
N 12
N 12
N 13
N 14
AN 15
AN 16
AN 17
AN 18
AN 19
AN 20
AN 22
AN 22
AN 24
AN 26
AN 28
AN 30
AN 32
AN 34
AN 36
AN 40
N 44
W 07
W 08
W 09
W 10
W 11
W 12
W 12
W 13
W 14
W 15
W 16
W 17
W 18
W 19
W 20
W 22
W 22
W 24
W 26
W 28
W 30
W 32
W 34
W 36
W 40
W 44
Mass
Dimensions
Removal
nut
N 09
N 10
RN 10
RN 11
RN 12
AN 15
AN 16
AN 17
AN 18
AN 19
AN 20
AN 21
AN 22
ARN 21
ARN 22
ARN 24
ARN 26
RN 28
RN 30
RN 32
RN 34
RN 36
RN 38
N 44
N 48
N 052
3)
da
B1
lb
in
in
in
0.25
0.31
0.47
0.56
0.69
0.84
1.55
1.80
2.00
2.25
2.55
2.95
3.40
3.90
4.25
5.00
8.00
9.50
11.50
15.50
17.50
20.50
22.00
25.50
29.50
34.00
1.377
1.574
1.771
1.968
2.164
2.361
2.361
2.558
2.755
2.952
3.149
3.346
3.543
3.740
3.937
4.330
4.527
4.921
5.315
5.512
5.906
6.299
6.693
7.087
7.874
8.661
1.575
1.732
1.969
2.126
2.244
2.402
2.559
2.717
2.835
2.953
3.150
3.346
3.543
3.701
3.858
4.134
4.523
4.921
5.512
5.512
5.748
6.063
6.299
6.693
7.126
7.441
0.118
0.118
0.118
0.118
0.138
0.138
0.138
0.138
0.138
0.138
0.138
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.236
0.236
0.236
0.276
0.276
0.315
0.315
D1
in
21732
21116
3932
312
4
378
417
41332
42132
41532
5316
5716
52332
6
657
71332
72532
81732
9532
92532
101332
102932
11716
11
11716
12316
16
2
9
16
9
16
5
8
9
32
19
32
5
8
11
16
23
32
3
4
3
4
25
32
3
4
3
4
13
16
7
8
5
16
1
1
1116
1116
1316
114
11132
11332
7
1
Mean thread Threads

pitch
per
diameter
inch
d2
1.7277
1.9277
2.1644
2.3674
2.5864
2.8752
3.0790
3.2812
3.4682
3.6712
3.8592
4.0618
4.2648
4.4988
4.7178
5.1248
5.5618
6.0083
6.8363
6.8363
7.2423
7.6643
8.1019
8.5378
9.3245
10.0742
1)
18
18
18
18
18
12
12
12
12
12
12
12
12
12
12
8
8
8
8
8
8
8
8
8
6
6
1) Threads derived from the Screw Threads Standards for Federal Services Handbook H-28 (1944) page 111, and H-28 (1957) Part 1, page 181, Class 3.
2) Last two figures of bearing designation.
3) Stickout before the sleeve is pressed into the bearing bore.
439
Split pillow blocks

(metric series)
Nomenclature
F SNL 522-619 NMSN

4
2
3
1
1. Prefix:
4. Suffix:
Two holes for attachment bolts
NM
Four drilled holes for

attachment bolts
Drilled and tapped hole

1/8-27 NPSF at center of cap,
one grease nipple supplied
Grease escape hole in base
No holes
VU
Cap drilled, tapped and plugged

with two holes 1/8-27 NPSF;
Base drilled diagonally opposite,
tapped and plugged with two holes
1/8-27 NPSF;
One grease fitting AH 1/8-27 PTF
supplied with housing

1/4-28 UNF at one side of cap,
one grease nipple supplied
TD

1/4-28 UNF at both sides of cap,
two grease nipples supplied
SN

for sensor
K7
Bearing seating diameter

tolerance K7
Fixed (large size blocks)
Loose (no stab ring large

size blocks)
2. Housing styles:
SNL
Housing of gray cast-iron
SNLD
Housing of ductile-iron
3. Housing size:
205 to 218
505 to 532
Where two or more suffixes are used they

are given in the same order as above
441
Split pillow blocks (metric series)

Introduction
Fewer bearing replacements and less maintenance

Plummer (pillow) block housings have
much to offer
SNL plummer (pillow) block housings

have more to offer
The main benefit of split plummer block housings is their easy installation; pre-assembled
shafts can be mounted in them. When the
housing bases are attached to the base plate it
is then only necessary to place the housing caps
in position and to tighten the attachment bolts
to complete the installation.
Split plummer block housings available on the
market are mainly intended for self-aligning ball
bearings, spherical roller bearings and CARB
bearings of ISO dimension series 02, 03, 22, 23
and 32. They can often be fitted with various
seals. Many designs and variants of split
plummer block housings are available making
the use of tailored housings unnecessary and
thus enabling cost effective bearing arrangements to be made.
For many years SKF has been one of the
leading producers of split plummer block
housings synonymous with operational
reliability, quality and versatility.
SKF has developed the SNL plummer block

housings to be the first choice for design, quality
and economy. This enables customers to keep a
step ahead.
SNL plummer block housings enable the full
service life potential of the incorporated bearings
to be exploited with less need of maintenance.
This supports user efforts to further reduce
maintenance costs. Among other characteristics
the housings are very stiff, making them insensitive to uncontrolled and excessive tightening of
the attachment bolts.
Another benefit is the choice of oil or grease
lubrication for the bearings housed in SNL
plummer blocks. A range of efficient seals for oil
lubrication and rough environments make for
trouble-free operation.
442
Introduction
One basic design - many variants

SNL plummer block housings are primarily
intended for self-aligning ball bearings, spherical
roller bearings and CARB bearings. The housings are designed on a building block principle.
This enables a more generous choice of bearing,
shaft mounting, seals and type of lubrication.
Stocking is also simplified.
A building block system
Several sealing options
The basis of the SNL plummer block housing

system consists of a number of housings of the
same design but in different sizes. By combining
these housings with the different standard seals
a wide variety of housing variants, all belonging
to the standard range, can be supplied to cover
the majority of demands for plummer blocks for
shafts having diameters of 20 to 160 mm,
inclusive. The standard range also covers other
variants, for example, housings with drilled and
tapped holes for lubrication nipples or condition
monitoring sensors. Housings are also available
for bearings for larger shaft diameters
(see page 488).
SNL plummer block housings are made of
grey cast-iron and demonstrate high strength.
Should, however, this strength be inadequate,
dimensionally equivalent plummer block housings of ductile iron (spheroidal graphite castiron) can be supplied.
An important advantage of the SNL plummer

block housings is that they can be fitted with a
variety of seals. The standard seals supplied by
SKF comprise double-lip seals, V-ring seals, felt
seals, labyrinth seals and heavy-duty taconite
seals as well as end covers. Other standard
seals are also available for SNL housings. The
housings need modification to accommodate the
seals. These are oil seals and heavy-duty axial
taconite seals.
SNL plummer block housings are fully interchangeable with the earlier SNH housings. Their
dimensions conform to ISO 113:1994.
Painting system
Resulting from customer surveys, SNL plummer
block housings are painted as standard in accordance with ISO 12944-2, environmental Class
C2. Black color: RAL 9005.
443

Seals
Standard seals
An important advantage of SNL plummer block
housings is that they can be fitted with different
types of seal. The standard seals available from
SKF are split double-lip seals and felt seals,
one-piece V-rings, labyrinth seals and the
heavy-duty taconite seals. The seals are easy
to install and are supplied separately.
All the standard seals as well as the seals for
use with oil lubrication are presented in Table 1
which gives a comprehensive overview of the
seal types, their design features and their suitability for various operating conditions. Detailed
information on the various standard and special
seals, including properties and availability, will
be found on pages 446 to 450.
TSN .. G
TSN .. A
TSN .. C
TSN .. S
TSN .. ND
TSN .. TURU1)
Table 1
Seal selection
TSN..G
TSN..A
TSN..C
TSN..S
TSN..ND
TSN..TURU1)
Temperature
40 to +212 F
(40 to +100 C)
40 to +212 F
(40 to +100 C)
40 to +212 F
(40 to +100 C)
58 to +392 F
(50 to +200 C)
40 to +212 F
(40 to +100 C)
40 to +392 F
(40 to +200 C)
Peripheral speed
Up to 26 ft/sec
(Up to 8 m/sec)
Up to 23 ft/sec
(Up to 7 m/sec)
Above 23 ft/sec 2)
(Above 7 m/sec 2))
Up to 13 ft/sec
(Up to 4 m/sec)
++
++
Up to 39 ft/sec
(Up to 12 m/sec)
++
++
Misalignment, degrees
0.5 to 1
1 to 1.5
Up to 0.5
Up to 0.3
Up to 0.5
Up to 1
Relubrication grease
13 ft/sec 3)
(4 m/sec 3))
++4)
Oil lubrication
--
++
Low friction
++
++
++
Axial shaft displacement
++
++
Internal conditions
5)
Vertical mounting
++
--
--
--
Replacement
++
Dust
++
++
Sand
++
++
Grit
++
Sharp objects,
chipping splinters, etc.
--
++
++
++
Liquids when sprayed
--
++
Direct sunshine
--
++
++
++
++
External conditions
Symbols:
1)
2)
3)
4)
5)
444
++
very suitable
suitable
Delivered as a complete unit only, i.e. housing with seals.

When V-ring axially supported.
When using housing with grease escape hole (suffix V).
If appropriate components are used: ASNA .. V.
When the V-ring of the lower seal is mounted inboard.
limited suitability
--
unsuitable
Seals
A design
V-ring seals
C design
felt seals
G design
double-lip seals
Table 2
Permissible shaft speeds for rubbing seals
Shaft
diameter
Guideline values for the permissible shaft speed1)

for standard seals of design
da, db
C2)
mm
r/min
20
25
30
3 820
3 060
2 550
6 680
5 350
4 460
7 640
6 110
5 090
35
40
45
2 180
1 910
1 700
3 820
3 340
2 970
4 360
3 820
3 390
50
55
60
1 530
1 390
1 270
2 670
2 430
2 230
3 060
2 780
2 550
65
70
75
1 180
1 090
1 020
2 060
1 910
1 780
2 350
2 180
2 040
80
85
90
960
900
850
1 670
1 570
1 490
1 910
1 800
1 700
95
100
110
800
760
690
1 410
1 340
1 220
1 610
1 530
1 390
115
120
125
660
640
610
1 160
1 110
1 070
1 330
1 270
1 220
130
135
140
590
570
550
1 030
990
960
1 180
1 130
1 090
145
150
155
530
510
490
920
890
860
1 050
1 020
990
160
165
170
480
460
450
840
810
790
960
930
900
The speeds are valid when the seals are operated at temperatures between 40 to +212 F (40 to +100 C)
(permissible temperature range). At temperatures outside this range and/or at speeds higher than those given,
labyrinth seals should be used.
1)
2)
The guideline values are based on the permissible sliding speed at the seal/counterface contact. However,
the permissible shaft seal is determined by the speed rating for the bearing to be used in the housing.
The guideline values are based on a peripheral speed of 13 ft/sec (4 m/sec). Higher speeds are possible,
see under Felt ring seals.
445

Seals
Double-lip seals
V-ring seals
Double-lip seals (Figure 1) are made of

polyurethane, a wear-resistant material which
has good elastic properties. The seals are split
so that they are easy to fit. They are intended
for grease lubrication and can be used at
peripheral speeds of up to 26 ft/sec (8 m/sec).
The permissible angular misalignment is
approximately 1 for shaft diameters up to
approximately 100 mm and 0.5 for larger
sizes. The seal counterface on the shaft should
be ground and the surface roughness Ra should
not exceed 126 in (3.2 m). The recommended shaft tolerance is h9. When using housings
with grease escape hole (suffix V) the speed
limit is 13 ft/sec (4 m/sec) due to increased
pressure on the inner seal lip.
The axial movement of the shaft relative to
the housing is not limited when double-lip seals
are used.
The double-lip seals are always supplied in
packs of two seals. When housings are used at
shaft ends, i.e. with one end cover, one of the
seals will be left over and can be kept as a
spare. The double lip seals are identified by the
designation prefix TSN followed by the size
identification and the suffix G, e.g. TSN 511 G.
The V-ring seals (Figure 2) consist of a

V-ring and a sheet steel sealing washer with
vulcanized rubber lip which fits into the sealing
groove in the housing. The washer is protected
against corrosion. The V-rings are made of
synthetic rubber and have a slim sealing lip,
which seals axially against the sealing washer.
The V-ring body, which sits tightly on the
shaft and rotates with it, also serves as a
flinger. V-ring seals provide efficient sealing
even under difficult operating conditions such as
high speeds, rough finished shafts etc. They
can be operated at peripheral speeds in excess
of 7 m/s if the V-ring is prevented from moving
or lifting from the shaft by a support ring.
Recommended dimensions for appropriate
support rings (for axial and radial location) are
given in Table 3.
The permissible angular misalignment for
V-ring seals is approximately 1.5 for a 50 mm
shaft decreasing to approximately 1 for a shaft
diameter of 150 mm and above. The axial
movement of the shaft relative to the housing
is limited to 1 mm for shaft diameters up to
65 mm and to approximately 1.2 mm for
larger shaft diameters.
Figure 1
The V-ring seals are always supplied in packs

of two seals. When housings are used at shaft
ends, i.e. with one end cover, one of the seals
will be left over and can be kept as a spare.
The V-ring seals are identified by the designation prefix TSN followed by the size identification and the suffix A, e.g. TSN 511 A.
Figure 2
Location of V-ring
Peripheral speed 7 m/s
Double-lip seal
446
V-ring seal
Peripheral speed
7 to 12 m/s
Peripheral speed
above 7 m/s
Seals
A
G1
120
d1
>12 m/s
7-12 m/s
Table 3
Recommended dimensions for support rings for V-ring seals
Shaft
diameter
Dimensions
da, db
d1
mm
mm
20
25
30
20
25
30
27.2
32.1
37.2
5
5
5
8.5
8.5
8.5
3.5
3.5
3.5
30
35
40
2.5
2.5
2.5
35
40
45
35
40
45
42.2
49.1
54
5
7
7
8.5
11.5
11.5
3.5
4.5
4.5
45
53
58
50
55
60
50
55
60
59.1
64.1
69.1
7
7
7
11.5
11.5
11.5
4.5
4.5
4.5
65
70
75
65
70
75
74.1
81
86
7
9
9
11.5
15
15
80
85
90
80
85
90
91
96
101
9
9
9
95
100
110
95
100
110
106
111
122.9
115
125
135
115
125
135
140
145
155
165
175
d2
B1
B2
Grub
screw
to
G1
V-ring
Designation
DIN 913
M3
M3
M3
35
35
35
CR 400200
CR 400250
CR 400300
2.5
3.5
3.5
M3
M4
M4
35
45
45
CR 400350
CR 400400
CR 400450
63
68
73
3.5
3.5
3.5
M4
M4
M4
45
45
45
CR 400500
CR 400550
CR 400600
4.5
6
6
78
84
89.5
3.5
4.5
4.5
M4
M5
M5
45
56
56
CR 400650
CR 400700
CR 400750
15
15
15
6
6
6
94.5
100
105
4.5
4.5
4.5
M5
M5
M5
56
56
56
CR 400800
CR 400850
CR 400900
9
9
10
15
15
7.5
6
6
7.5
109
115
128
4.5
4.5
5
M5
M5
M6
56
56
68
CR 400950
CR 401000
CR 401100
127.4
138.1
147.5
10
10
10
17.5
17.5
17.5
7.5
7.5
7.5
133
143
153
5
5
5
M6
M6
M6
68
68
68
CR 401100
CR 401300
CR 401300
140
145
155
152.9
158.1
167.5
10
10
10
17.5
17.5
18.5
7.5
7.5
8.5
158
163
173
5
5
5
M6
M6
M6
68
68
68
CR 401400
CR 401500
CR 401500
165
175
179.9
189.3
10
10
18.5
18.5
8.5
8.5
185.5
195
5
5
M6
M6
68
68
CR 401700
CR 401700
447

Seals
Felt ring seals

Felt ring seals (Figure 3) are simple but
efficient seals for use with grease lubrication.
They can be operated at peripheral speeds up to
13 ft/sec (4 m/sec). The seals can be used at
much higher speeds but at high speeds a small
gap will be formed between the felt and the
shaft and the seal becomes a non-rubbing gaptype seal. For plummer block housings with
bearings on adapter sleeves on cylindrical shafts
the felt ring seals are split. The impregnated felt
is inserted in light alloy half-rings. It is only
necessary to insert the seals in the grooves in
the housing. The rubber O-section cords should
be put into the grooves first as they prevent the
seal rings from turning.
SNL plummer block housings for bearings
mounted on cylindrical seatings on stepped
shafts, sizes 205 to 218 inclusive, can also be
supplied with felt seals. In this case the seals
consist of loose felt strips, which can be inserted
in the sealing grooves. Before mounting, the
FS felt strips should be left to soak for a few
minutes in hot oil.
For applications with spherical roller bearings

or CARB bearings, which are to operate at
continuously high temperatures up to approximately 482 F (+250 C), SKF graphited FSB
sealing strips, made of aluminum boron
silicate, can be used. They are suitable for
peripheral speeds up to 6.5 ft/sec (2 m/sec).
The strips have been well proven as seals on
autoclave trucks.
The permissible angular misalignment is
approximately 0.5. The seal counterface on
the shaft should be ground and the surface
roughness Ra should not exceed 126 in
(3.2 m).
the housing is not limited when felt seals
are used.
The ready-to-mount felt ring seals
(in light alloy half-rings) are always supplied in
packs of two seals. When housings are used at
shaft ends, i.e. with one end cover, one of the
seals will be left over and can be kept as a
spare. The felt ring seals are identified by the
designation prefix TSN followed by the size
identification and the suffix C, e.g. TSN 511 C.
The felt ring seals can also be supplied with an

FSB insert. The rubber O-section cords are
replaced by fluoro rubber O-section cords.
These seals are identified by the suffix CB,
e.g. TSN 511 CB.
Figure 3
Ready-to-mount felt ring seal
Felt ring seal
448
Felt strips
Seals
Labyrinth seals
Under difficult operating conditions and/or at
high speeds the use of labyrinth seals (Figure 4)
is recommended. The labyrinth rings are made
of steel and have two radially arranged labyrinth
steps, which form a narrow sealing gap with the
housing grooves.
Hollow O-ring cords of silicone rubber
(supplied with the seals) allows the labyrinth
rings, which are mounted with a loose fit, to
rotate with the shaft. Angular misalignments
of the shaft up to approximately 0.3 are permissible. The operating temperature range for
the labyrinth seals is 58 to +392 F (50 to
+200 C).
When labyrinth seals are used, axial movement of the shaft relative to the housing is not
limited. The recommended shaft tolerance is h9.
The labyrinth seals are supplied singly. For
bearing arrangements for through shafts it is
therefore necessary to order two rings. The
labyrinth seal is identified by the prefix TSN
followed by the size identification and the
suffix S, e.g. TSN 511 S.
Figure 4
Labyrinth seal
Taconite heavy-duty seals

Taconite is a very fine-grained mineral which
is extremely difficult to seal out. For bearing
arrangements, which must operate under very
arduous conditions (such as those encountered
in mining), labyrinth seals, which can be relubricated, are recommended; grease enhances
the sealing effect and extends the serviceability
of the seals. SKF has developed two different
designs of these heavy-duty seals (which can
seal out taconite, hence the name) which can
be supplied for use with SNL housings.
The one taconite seal design (Figure 5)
is based on a radial labyrinth seal and fits the
standard housings. A V-ring seal mounted on
the shaft seals against the non-rotating part of
the seal, which is inserted in the seal groove
and prevents contaminants from penetrating
the bearing when the seal is relubricated. This
grease is supplied via a grease nipple in the
non-rotating part of the seal. Angular
misalignments of the shaft of up to approximately 0.5 are possible. The permissible
operating temperature range for the seal is
between 40 to +212 F (40 and +100 C).
the housing is limited for this type of taconite
seal to 1 mm for shaft diameters up to 65
mm and to approximately 1.2 mm for sizes
up to 100 mm and 1.5 mm for larger shaft
diameters. The recommended shaft tolerance
is h9.
Figure 5
Taconite heavy-duty seal
These seals are supplied singly so that for

housings used on through shafts, it is
necessary to order two seals. The seal is identified by the prefix TSN followed by the size
identification and the suffix ND,
e.g. TSN 511 ND.
The other design of taconite seal (Figure 6)
is based on a labyrinth seal with the labyrinth
stages arranged axially and does not fit the
standard housings. The seal is relubricated via
lubrication holes and nipples in the housing
cap. The positions for the holes are marked by
dimples in the casting. The permissible misalignment of the shaft relative to the housing
for this seal is approximately 0.5. The operating temperature range is from 40 to +482 F
(40 to +250 C). Axial movement of the
shaft relative to the housing is also limited. The
recommended shaft tolerance is h9.
The modified SNL housings are always supplied together with the seals and are available
from size 515-612. The housings with seals
are identified by the designation suffix TNC, e.g.
SNL 515 TNC or SNL 612 TNC. A housing
intended for a shaft end with one seal and one
end cover is identified by an additional suffix A,
e.g. SNL 515 ATNC. The seal itself is
designated TSN .. NC.
A variant of the TNC seal with an additional
V-ring can also be supplied. The seal is identified by the letters TNB and can be supplied
to order.
Figure 6
449

Seals
Special seals
Seals for oil lubrication

Special seals (oil seals) are required to prevent
oil from escaping from the housing when oil
lubrication is applied. For SNL housings, SKF
has developed the non-rubbing seal of the U
design (Figure 7). These U seals also require
modified housings and comprise two parts:
one that is stationary and is screwed to the
housing and the other that is mounted on the
shaft and rotates. A hollow O-ring cord of silicone rubber inserted between the labyrinth
ring and the shaft allows the ring, which is
mounted with a loose fit, to rotate with the
shaft, and oil cannot escape along the shaft.
These oil seals do not limit axial movement of
the shaft relative to the housing. The recommended shaft tolerance is h9.
The modified SNL housing is supplied
together with the seals as a unit. The housings
with seals are identified by the suffix TURU, e.g.
SNL 524 TURU. Special end covers can be
supplied separately on request, designation
ASNH .. R.
Figure 7
Applications where, for some reason, the

standard seals cannot be used, must be fitted
with special seals. The SNL housings can be
supplied without seals for such applications
and are relatively easy to equip with special
seals. It is recommended that housings of
series SNL 2 are used rather than those of
series SNL 5-6 as they have a comparatively
larger bore at the shaft entrance. There is
therefore more room to accommodate a seal,
so that there are more choices for seal design.
Special seals are not normally supplied by
SKF. Therefore, the relevant housing dimensions are given in Table 4.
A6
A5
Db DC
A4
A3
Table 4
Sealing groove dimensions
Housing
Size
Dimensions
A4
A3
mm
SNL 205
SNL 206-305
SNL 207
44
54
58
SNL 208-307
SNL 209
SNL 210
A5
A6
Db
Dc
5
5
5
7.5
7.5
8
10
10
11
36.5
46.5
56.5
44.5
54.5
64.5
61
59
64
5
5
5
8
9
9
11
12
12
62
67
72
70.5
75.5
80.5
SNL 211
SNL 212
SNL 213
69
79
82
5
5
5
9
9
9
12
12
13
77
87
92.5
85.5
95.5
101
SNL 215
SNL 216
SNL 217
SNL 218
87
92
97
112
5
5
5
5
9
9
9
9
13
13
13
13
102.5
108
112
120
111
116.5
120.5
128.5
SNL 505
SNL 506-605
SNL 507-606
45
55
59
5
5
5
7.5
7.5
8
10
10
11
31.5
36.5
46.5
39.5
44.5
54.5
SNL 508-607
SNL 509
SNL 510-608
62
60
65
5
5
5
8
9
9
11
12
12
51.5
56.5
62
59.5
64.5
70.5
SNL 511-609
SNL 512-610
SNL 513-611
70
80
83
5
5
5
9
9
9
12
12
13
67
72
77
75.5
80.5
85.5
SNL 515-612
SNL 516-613
SNL 517
88
93
98
5
5
5
9
9
9
13
13
13
87
92.5
97.5
95.5
101
106
SNL 518-615
SNL 519-616
SNL 520-617
113
116
131
5
6
6
9
10
10
13
14
14
102.5
131
137.5
111
141
147.5
SNL 522-619
SNL 524-620
SNL 526
143
151
156
6
6
6
10
11
11
14
15
15
147.5
157.5
167.5
157.5
167.5
177.5
SNL 528
SNL 530
SNL 532
171
189
201
6
6
6
11
11
11
15
15
15
177.5
192.5
202.5
187.5
202.5
212.5
Oil seal
450
End covers
End covers
For housings mounted at the ends of shafts,
the one opening should be fitted with an end
cover, which fits into the seal groove (Figure 8).
Details of the permissible length of the shaft
end can be found in Table 5. The end covers
are of plastic and are suitable for operating
temperatures in the range 40 to +230 F
(40 to +110 C).
At higher temperatures sheet steel end covers should be used instead. These can be cut
out from steel sheets and should be inserted
with a hollow O-ring cord of silicone rubber in
the seal groove in the housing. The relevant
seal groove dimensions are given in Table 4.
The standard end cover of plastic is designated
by the prefix ASNH followed by the housing size
identification, e.g. ASNH 511-609.
Ca
Ca
ba
bc
Table 5
Permissible length of shaft end
Dimensions
ba
mm
bc
Ca
Widest bearing to fit housing

Designation
Dimensions
B
bb
mm
SNL 205
SNL 206-305
SNL 207
18
20
23
24
29
32
25
32
34
22205 CC/W33
22206 CC/W33
22207 CC/W33
18
20
23
17
18
20.5
SNL 208-307
SNL 209
SNL 210
26 (22)
25
28 (24)
33
32
35
39
30
41
22208 E
22209 CC/W33
22210 CC/W33
23
23
23
21.5
22.5
23.5
SNL 211
SNL 212
SNL 213
30 (25)
33 (26)
35 (30)
37
42
45
44
48
51
22211 E
22212 E
22213 CC/W33
25
28
31
25
27
29.5
SNL 215
SNL 216
SNL 217
SNL 218
37 (30)
39 (33)
40 (35)
45 (35)
47
50
52
60
56
58
61
65
22215 E
22216 E
22217 E
23218 CC/W33
31
33
36
52.4
30.5
33.5
36
44.2
SNL 505
SNL 506-605
SNL 507-606
18
20
23
24
29
32
25
32
34
22205 CCK/W33
2305 EK
2306 K
18
24
27
17
19
21.5
SNL 508-607
SNL 509
SNL 510-608
26 (22)
25
28 (24)
33
32
35
39
30
41
2307 EK
22209 CCK/W33
22308 CCK/W33
31
23
33
24.5
22.5
26.5
SNL 511-609
SNL 512-610
SNL 513-611
30 (25)
33 (26)
35 (30)
37
42
45
44
48
51
22309 CCK/W33
22310 EK
22311 EK
36
40
43
29
32
33.5
SNL 515-612
SNL 516-613
SNL 517
37 (30)
39 (33)
40 (35)
47
50
52
56
58
61
22312 EK
22313 EK
22217 EK
46
48
36
36
38
36
SNL 518-615
SNL 519-616
SNL 520-617
45 (35)
47 (40)
51 (45)
60
61
69
65
68
70
22315 EK
22316 EK
23220 CCK/W33
55
58
60.3
42.5
46
50.2
SNL 522-619
SNL 524-620
SNL 526
61
65
65
75
79
81
80
86
90
23222 CCK/W33
23224 CCK/W33
23226 CCK/W33
69.8
76
80
55.9
60
63
SNL 528
SNL 530
SNL 532
70
80
85
89
98
104
98
106
114
23228 CCK/W33
23230 CCK/W33
23232 CCK/W33
88
96
104
68
74
80
1)
Housing with end cover
bb
ba
bc
Housing
Size
Figure 8
bb
1)
The dimension ba is determined to suit all appropriate bearings with two exceptions:
1. With self-aligning ball bearings of series 12 where the total bearing seating width must be available, the values
given in brackets apply.
2. For non-locating arrangements with the widest bearings, as listed above, which are not mounted centrally in
the housing, the value of ba must be either correspondingly reduced or correspondingly increased.
451

Locating rings
Locating rings
The bearing seating in the housing is
sufficiently wide to enable the bearing to be
displaced axially. The locating or held bearing
must always be fixed axially in position in the
housing bore by locating rings at both sides
(Figure 9).
CARB bearings are non-locating bearings
and cannot take axial loads. Since axial
displacement is accommodated within a CARB
bearing (together with any misalignment), it is
necessary to locate the outer ring axially in its
seating by inserting a locating ring at each
side of the bearing.
The locating rings are identified by the prefix
FRB followed by figures giving the width/outside diameter in millimeters, e.g. FRB 11.5/100.
Figure 9
Housing with locating rings

at both sides of bearing
452
Axial displacement of
CARB bearings in SNL
housings
The permissible axial displacement in a CARB
bearing is dependent on the clearance
remaining in the bearing after mounting: the
larger the residual radial internal clearance,
the larger the permissible axial displacement
of one ring with respect to the other. This axial
displacement reduces the clearance in the
bearing until at a given displacement, the
clearance disappears altogether or the rollers
may start to be exposed at one side of the
bearing.
Table 6 shows the maximum permissible
axial displacement for each CARB bearing
having Normal initial radial internal clearance
when mounted normally. It is assumed that
there is little difference in temperature
between inner and outer ring.
Figure 10
CARB bearing on adapter sleeve

with spacer ring between bearing
inner ring and lock nut
When the rings are displaced a certain

distance, the roller and cage assembly will move
through half this distance. If the inner ring
moves into the bearing, or alternatively, if the
outer ring moves out from the bearing, the
roller and cage assembly can contact the lock
nut and locking washer. For bearings of series
C 22 K up to and including size 22, therefore, a
special adapter sleeve with a narrow slot and a
self-locking KMFE nut must be used to prevent
this from happening (Figure 10). Such sleeves
are supplied by SKF and identified by suffix E,
e.g. H 311 E.
For bearings of series C 22 K and C 32 K,
from size 24 and above, the adapter sleeves are
supplied together with a KML nut, indicated by
suffix L in the sleeve designation, e.g. H 2324 L.
It should be observed that the possible axial
displacement of the shaft relative to the housing
may be limited by the type of seal used.
Axial displacement
Table 6
Axial displacement for mounted CARB bearings
Bearing
Housing
Size
Axial displacement s1) for mounted CARB

bearings with initial radial internal clearance
Normal
mm
C 2205 K
SNL 505
2.3
C 2206 K
SNL 506-605
2.3
C 2207 K
SNL 507-606
2.8
C 2208 K
SNL 508-607
2.7
C 2209 K
SNL 509
3.1
C 2210 K
SNL 510-508
2.9
C 2211 K
SNL 511-609
3.5
C 2212 K
SNL 512-610
3.6
C 2213 K
SNL 513-611
3.7
C 2215 K
SNL 515-612
4.4
C 2315 K
SNL 518-615
5.9
C 2216 K
SNL 516-613
4.4
C 2316 K
SNL 519-616
5.7
C 2217 K
SNL 517
5.1
C 2317 K
SNL 520-617
6.5
C 2218 K
SNL 518-615
5.2
C 2220 K
SNL 520-617
5.4
C 2320 K
SNL 524-620
6.8
C 2222 K
SNL 522-619
6.7
C 3224 K
SNL 524
7.8
C 2226 K
SNL 526
8.0
C 2228 K
SNL 528
8.0
C 2230 K
SNL 530
9.3
C 3232 K
SNL 532
10.5
1)
s is the maximum permissible displacement of one ring with respect to the other in one direction; the total axial displacement is twice as large.
453

Lubrication
Lubrication
SNL plummer block housings are designed so
that the bearings can be lubricated with grease
or oil, although grease lubrication is generally
preferable. The lubricant should be selected
with reference to the operating conditions.
Grease lubrication
Table 7
Grease quantities
Housing
Size
In the majority of applications, the amount of

grease applied to the SNL housings when
mounting (initial fill) or after an inspection is
adequate until the next planned inspection.
Certain operating conditions, e.g. high speeds,
high temperatures or heavy loads, may mean
that more frequent relubrication is necessary.
Table 7 gives guideline values for the grease
Grease quantities
First
Relubrication
fill
1)
SNL 205
SNL 206-305
SNL 207
25
40
50
5
5
10
SNL 208-307
SNL 209
SNL 210
60
65
75
10
10
10
SNL 211
SNL 212
SNL 213
100
150
180
15
15
20
SNL 215
SNL 216
SNL 217
SNL 218
230
280
330
430
20
25
25
40
SNL 505
SNL 506-605
SNL 507-606
25
40
50
5
5
10
SNL 508-607
SNL 509
SNL 510-608
60
65
75
10
10
10
SNL 511-609
SNL 512-610
SNL 513-611
100
150
180
15
15
20
SNL 515-612
SNL 516-613
SNL 517
230
280
330
20
25
25
SNL 518-615
SNL 519-616
SNL 520-617
430
480
630
40
50
55
SNL 522-619
SNL 524-620
SNL 526
850
1 000
1 100
70
80
95
SNL 528
SNL 530
SNL 532
1 400
1 700
2 000
110
130
150
1)
Figure 11
Figure 12
Fills approximately 40% of the free space in the

housing.
Lubricating the bearing

via the outer ring
454
quantities to be applied for the initial fill and

for relubrication. Seven markings will be found
on the housing cap of which six show where
holes can be drilled and tapped to take grease
nipples.
There is also a drilled and tapped hole for
the grease nipple AH 1/8-27 PTF, which is
supplied with the housing. This hole is closed
by a plastic plug. The two markings at the
outer sides of the central ridge indicate the
position for lubrication holes for the seals.
It is recommended that spherical roller
bearings having a lubrication groove and
three holes in the outer ring (designation suffix
E or W33) be lubricated via this feature
(Figure 11). A hole should be drilled at one of
the middle markings on the three bars for this
purpose. SNL housings having a drilled and
tapped hole in the middle of the cap together
with a lubrication nipple and can be supplied
on request. They are identified by the designation suffix NM, e.g. SNL 511-609 NM.
Bearing lubrication via

the standard nipple
Lubrication
It should be noted that when spherical roller

bearings are to be relubricated via the outer
ring, they should be rotated. If outer ring
relubrication is not possible or if self-aligning
ball bearings or CARB bearings are used, the
standard grease nipple supplied with the
housing should be inserted in the hole provided and used for this purpose (Figure 12). If it
is desired to use a grease nipple other than
that supplied with the housing, adapters are
available which make a reworking of the available drilled and tapped hole unnecessary.
Where V-ring seals are used, the effectiveness of relubrication can be much improved if
an additional V-ring is mounted inside the
housing at the side where the grease is
applied, so that grease can only exit at the
opposite side of the housing. For this purpose
a set comprising a V-ring and a splash plate,
which covers a sector of more than 180
(Figure 13), can be supplied. This V-ring and
splash plate set is designated by the prefix
ASNA followed by the housing size identification and the suffix V, e.g. ASNA 511 V.
Where the bearings are mounted on
adapter sleeves, the grease should be introduced at the side opposite to the lock nut of
the sleeve. Where housings are mounted at
shaft ends, grease should be applied at the
end cover side.
Where G- or C-design seals are used, it should

be noted that grease cannot escape via the seals.
If frequent relubrication is required when such
seals are used, it is advisable to provide the
housing with a grease escape hole (Figure 14)
through which excess grease can escape.
Recommended dimensions will be found in
Table 8. SNL housings with a grease escape
hole in the base can be supplied. This housing
design is identified by the suffix V, e.g. SNL 511609 V.
If housings fitted with the G-design double-lip
seals are periodically relubricated, the seals can
only be operated at peripheral speeds up to 13
ft/sec (4 m/sec) as otherwise the sealing lips
may overheat and wear.
Figure 13
Housing with additional

V-ring and splash plate
Figure 14
Housing with grease

escape hole
N3
Ja
Table 8
Recommended dimensions for grease
escape hole
Housing
Size
Dimensions
N3
Ja
mm
degrees
SNL 205
SNL 206-305
SNL 207
8.5
10
10
10
10
10
45
45
45
SNL 208-307
SNL 209
SNL 210
9
10
11
10
10
10
45
45
45
SNL 211
SNL 212
SNL 213
10
9
13
12
12
12
45
45
45
SNL 215
SNL 216
SNL 217
SNL 218
12.5
14
17
20
12
16
16
16
45
45
45
40
SNL 505
SNL 506-605
SNL 507-606
8.5
10
10
10
10
10
45
45
45
SNL 508-607
SNL 509
SNL 510-608
9
10
11
10
10
10
45
45
45
SNL 511-609
SNL 512-610
SNL 513-611
10
9
13
12
12
12
45
45
45
SNL 515-612
SNL 516-613
SNL 517
12.5
14
17
12
16
16
45
45
45
SNL 518-615
SNL 519-616
SNL 520-617
20
20
21
16
16
16
40
50
50
SNL 522-619
SNL 524-620
SNL 526
21
24
22
20
20
20
50
55
55
SNL 528
SNL 530
SNL 532
23
25
25
20
20
20
50
55
60
The dimensions are those recommended when

the standard grease nipple AH 1/8-27 PTF is used (supplied with the housing) but can also be applied if nipples
having threads R 1/8, KR 1/8 or M 101 are used. An
adapter is available, which fits the SNL standard lubrication hole, designation LAPN 1/8. Using this adapter nipple
with thread G 1/4 and grease dispensers, e.g. SKF
SYSTEM 24, can be applied.
455

Lubrication
Oil lubrication
Figure 15
The new SNL housings can be used for oil lubrication at relatively high speeds. When using oil,
however, the specially developed U-design seals
should be incorporated to avoid oil loss from the
housing. These seals are described on page 450.
In order for these seals to be used, the housing
must be modified so that SNL housings for oil
lubrication are only supplied complete with seals.
Housing for oil lubrication
Table 1
Recommended oil levels for SNL..TURU plummer blocks of series 5(00)
For series 3(00) and 6(00) please contact SKF Applications Engineering
Housing
Designation
Oil level for bearings of series

12
22
min
max
min
max
232
min
max
222
min
max
C 22
min
max
mm
SNL 511 TURU

SNL 512 TURU
SNL 513 TURU
27
23
29
31
27
33
27
22
28
32
28
34
27
23
28
31
27
33
28
23
29
32
26
34
SNL 515 TURU

SNL 516 TURU
SNL 517 TURU
24
34
30
29
39
36
23
33
30
29
40
36
23
33
29
28
39
35
24
34
30
29
39
36
SNL 518 TURU

SNL 519 TURU
SNL 520 TURU
31
38
34
38
45
42
31
38
34
38
46
42
33
37
36
42
37
45
41
30
37
30
38
33
35
43
SNL 522 TURU

SNL 524 TURU
SNL 526 TURU
39
47
47
57
38
48
42
50
54
47
55
59
37
46
50
46
55
59
39
48
52
62
46
48
50
52
54
57
44
45
47
52
54
57
40
44
51
57
SNL 528 TURU

SNL 530 TURU
SNL 532 TURU
The oil level is measured from the base of the housing. Mark the min and max level on the sight glass.
456
Mounting
Mounting
SNL housings together with SKF bearings are
robust and operationally reliable bearing
arrangements which have long lives. However,
if they are to achieve their full potential and
not fail prematurely, they must be properly
mounted. Incorrect procedures or unsuitable tools can influence life negatively.
Mounting the bearing

The bearings can be mounted either on a
tapered seating normally for SNL housings
in the form of an adapter sleeve or on a
cylindrical seating. When a bearing is correctly
mounted on a sleeve, there will be interference
fits between the inner ring, sleeve and shaft.
The degree of interference is determined by
how far the bearing is driven up on the sleeve
and either the internal clearance reduction or
the axial drive-up distance can be used as a
measure. The clearance reduction in spherical
roller bearings can be measured using a feeler
gauge, or the new SKF drive-up method can
be used.
When mounting self-aligning ball bearings
having Normal radial internal clearance (which
is relatively small) the clearance reduction can
be checked by turning and swivelling out the
outer ring. When the swivelling out meets a
slight resistance, the bearing has a sufficient
degree of interference and the drive-up
should be stopped. A particularly simple
method of mounting self-aligning ball
bearings on adapter sleeves is the use of the
spanner set TMHN 7, which has been specially
developed for this purpose. Each spanner is
marked with the angle to which the lock nut
should be turned when self-aligning ball
bearings having C3 radial internal clearance
are used.
CARB bearings can also be mounted on
cylindrical as well as tapered seatings. For
tapered seatings, adapter sleeves are normally
employed; the spanner set TMHN 7 can be
used for smaller CARB bearings as well as for
self-aligning ball bearings. For larger CARB
bearings either the clearance reduction or
the axial drive-up length should be measured.
When using a feeler gauge to measure
clearance reduction, it is important that the
inner and outer rings of the bearing are not
displaced with respect to each other. The new
SKF drive-up method can also be applied.
Table 10
Position and size of dowel holes
Housing
Size
Dimensions
J6
J7
Housing
Size
Dimensions
J6
J7
mm
mm
SNL 205
SNL 206-305
SNL 207
152
172
172
16
19
19
5
5
5
SNL 511-609
SNL 512-610
SNL 513-611
234
234
252
27
27
29
8
8
8
SNL 208-307
SNL 209
SNL 210
188
188
188
22
22
22
6
6
6
SNL 515-612
SNL 516-613
SNL 517
257
288
292
29
33
33
8
8
8
SNL 211
SNL 212
SNL 213
234
234
252
27
27
29
8
8
8
SNL 518-615
SNL 519-616
SNL 520-617
317
317
348
35
35
39
8
8
8
SNL 215
SNL 216
SNL 217
SNL 218
257
288
292
317
29
33
33
35
8
8
8
8
SNL 522-619
SNL 524-620
SNL 526
378
378
414
44
44
46
8
8
12
SNL 505
SNL 506-605
SNL 507-606
152
172
172
16
19
19
5
5
5
SNL 528
SNL 530
SNL 532
458
486
506
54
58
58
12
12
12
SNL 508-607
SNL 509
SNL 510-608
188
188
188
22
22
22
6
6
6
N4
max
Bearings with cylindrical bore are normally

mounted with an interference fit on the shaft.
Appropriate shaft tolerances should be
selected. The recommendations applying to
self-aligning ball and spherical roller bearings
also apply to CARB bearings.
N4
max
Support surface for housing base

To guarantee long bearing service life it is recommended that the support surface for the
housing is finished to Ra 492 in (12.5 m).
The flatness tolerance should be to IT7. For
moderate demands IT8 may be satisfactory.
Dowel pins
SNL housings are designed for loads acting
vertically to the housing base support. If they
are to be subjected to moderate or heavy loads
acting parallel to the base support, a stop
should be provided, or the housing should be
pinned to its support. Recommendations for
the position and size of holes to take dowel
pins are given in Table 10.
457

Mounting
Housings with four bolt holes in base

For the attachment of SNL housings to
T-shaped beams, it is possible to drill four bolt
holes in the base. The appropriate positions
are indicated by dimples. Recommended
dimensions are given in Table 11.
Some housings which are already prepared
for four-bolt mounting can be supplied. These
housings are also prepared for relubrication of
the bearing via the outer ring (suffix NM) as
standard. Available sizes are shown in Table
12. The housings are designated FSNL .. NM,
e.g. FSNL 511-609 NM.
Attachment bolts
It is recommended that hexagon-headed bolts
to strength class 8.8 according to
ISO 4014:1999 be used. If the load does not
act vertically to the base, it may be necessary
to use stronger, class 10.9 bolts. Details of the
appropriate tightening torques for the bolts to
class 8.8 are given in Table 14 on page 461.
458
Table 11
Bolt hole dimensions
Housing
Size
Dimensions
J1
J2
mm
SNL 208-307
SNL 209
SNL 210
160
160
160
34
34
34
11
11
11
M 10
M 10
M 10
SNL 211
SNL 212
SNL 213
200
200
220
40
40
48
14
14
14
M 12
M 12
M 12
SNL 215
SNL 216
SNL 217
SNL 218
220
252
252
280
48
52
52
58
14
18
18
18
M 12
M 16
M 16
M 16
SNL 508-607
SNL 509
SNL 510-608
160
160
160
34
34
34
11
11
11
M 10
M 10
M 10
SNL 511-609
SNL 512-610
SNL 513-611
200
200
220
40
40
48
14
14
14
M 12
M 12
M 12
SNL 515-612
SNL 516-613
SNL 517
220
252
252
48
52
52
14
18
18
M 12
M 16
M 16
SNL 518-615
SNL 519-616
SNL 520-617
280
280
300
58
58
66
18
18
18
M 16
M 16
M 16
SNL 522-619
SNL 524-620
SNL 526
320
330
370
74
74
80
18
18
22
M 16
M 16
M 20
SNL 528
SNL 530
SNL 532
400
430
450
92
100
100
26
26
26
M 24
M 24
M 24
N2
Appropriate
bolt size
mm
Mounting
Hole for grease nipple (standard)
Hole for grease nipple (NM design)
Dimple indicating
where to drill hole
for dowel pin
Table 12
Bolt hole dimensions
Housing
Size
Dimensions
N
N1
mm
FSNL 511-609 NM
FSNL 513-611 NM
FSNL 515-612 NM
20
20
20
FSNL 516-613 NM
FSNL 517 NM
FSNL 518-615 NM
J1
J2
J6
15
15
15
210
230
230
35
40
40
234
252
257
24
24
24
18
18
18
260
260
290
50
50
50
288
292
317
FSNL 520-617 NM
FSNL 522-619 NM
FSNL 524-620 NM
24
24
24
18
18
18
320
350
350
60
70
70
348
378
378
FSNL 526 NM
FSNL 528 NM
FSNL 530 NM
28
32
32
22
26
26
380
420
450
70
80
90
414
458
486
FSNL 532 NM
32
26
470
90
506
459

Load carrying ability
SNL plummer block housings are intended for

loads acting vertically towards the base plate
(support). If loads acting in other directions
occur, checks should be made to ensure that
the magnitude of the load is permissible for
the housing, the bolts joining the housing cap
and base, and for the attachment bolts.
Load carrying ability of the housing

Guideline values for the breaking load P of the
housing for various load directions are given
in Table 13. Using these values and a safety
factor selected with respect to the operating
conditions, the permissible load for the housing can be calculated. In general engineering a
safety factor of 6 is often used. For special
purposes where extra strength and resistance
to shock loads are required, SKF supplies as
standard a range of dimensionally equivalent
spheroidal graphite cast-iron housings. For
housings made of spheroidal graphite castiron, the values for P obtained from Table 13
should be multiplied by 1.8.
It is important for the load carrying ability of
the housing that the bolts joining cap and base
are properly tightened in accordance with the
values given in Table 14. The axial load carrying capacity of the housing is approximately
65% of P180. For load angles between 55
and 120 as well as for axial loads, if the load
acting parallel to the base plate (support surface) exceeds 5% of P180, the housing should
be pinned to the support or a stop should be
provided in the direction of the load.
Load carrying ability of the bolts

SNL plummer block housings are supplied
with cap bolts (to join cap and base) to
strength class 8.8 as standard. The guideline
values for the yield point Q for the cap bolts
are given in Table 14 for various load directions as well as the corresponding maximum
radial loads F.
IMPORTANT: Refer to text for determination of

permissible load
Table 13
Breaking loads for SNL plummer block housings
Housing
Size
Breaking loads for SNL housing

P55
P90
P120
kN*
SNL 205
SNL 206-305
SNL 207
155
170
190
95
100
115
SNL 208-307
SNL 209
SNL 210
215
230
265
SNL 211
SNL 212
SNL 213
P150
P180
Pa
70
80
85
60
65
80
80
85
95
52
55
60
130
140
155
95
100
120
85
90
110
110
115
130
70
75
85
275
300
340
170
180
205
125
130
150
115
120
130
140
150
170
90
100
110
SNL 215
SNL 216
SNL 217
SNL 218
410
430
480
550
250
260
290
340
185
190
205
250
160
175
190
215
205
215
240
275
135
140
155
180
SNL 505
SNL 506-605
SNL 507-606
155
170
190
95
100
115
70
80
85
60
65
80
80
85
95
52
55
60
SNL 508-607
SNL 509
SNL 510-608
215
230
265
130
140
155
95
100
120
85
90
110
110
115
130
70
75
85
SNL 511-609
SNL 512-610
SNL 513-611
275
300
340
170
180
205
125
130
150
115
120
130
140
150
170
90
100
110
SNL 515-612
SNL 516-613
SNL 517
410
430
480
250
260
290
185
190
205
160
175
190
205
215
240
135
140
155
SNL 518-615
SNL 519-616
SNL 520-617
550
580
620
340
350
370
250
260
280
215
230
250
275
290
310
180
190
200
SNL 522-619
SNL 524-620
SNL 526
680
790
900
410
470
540
310
350
410
275
320
360
340
400
450
220
260
295
SNL 528
SNL 530
SNL 532
1 050
1 200
1 450
630
730
860
470
540
640
430
480
570
530
600
720
345
390
470
* lbs = Kn x 225
460
Table 14
Load carrying ability and tightening torque for cap bolts and attachment bolts
Housing
Size
Cap bolts
Yield point
for both bolts
Q120
Q150
Q180
1)
Maximum load
for both bolts
F120
F150
Designation
Attachment bolts
Size
Tightening
torque
Nm2)
Nm2)
F180
1)
kN
SNL 205
SNL 206-305
SNL 207
150
150
150
85
85
85
75
75
75
50
50
50
30
30
30
25
25
25
50
50
50
M 1040
M 1040
M 1050
M 12
M 12
M 12
90
90
90
SNL 208-307
SNL 209
SNL 210
150
150
150
85
85
85
75
75
75
50
50
50
30
30
30
25
25
25
50
50
50
M 1050
M 1050
M 1055
M 12
M 12
M 12
90
90
90
SNL 211
SNL 212
SNL 213
220
220
220
125
125
125
110
110
110
80
80
80
45
45
45
40
40
40
80
80
80
M 1260
M 1260
M 1265
M 16
M 16
M 16
220
220
220
SNL 215
SNL 216
SNL 217
SNL 218
220
220
220
400
125
125
125
230
110
110
110
200
80
80
80
170
45
45
45
100
40
40
40
85
80
80
80
150
M 1265
M 1270
M 1280
M 1690
M 16
M 20
M 20
M 20
220
430
430
430
SNL 505
SNL 506-605
SNL 507-606
150
150
150
85
85
85
75
75
75
50
50
50
30
30
30
25
25
25
50
50
50
M 1040
M 1040
M 1050
M 12
M 12
M 12
90
90
90
SNL 508-607
SNL 509
SNL 510-608
150
150
150
85
85
85
75
75
75
50
50
50
30
30
30
25
25
25
50
50
50
M 1050
M 1050
M 1055
M 12
M 12
M 12
90
90
90
SNL 511-609
SNL 512-610
SNL 513-611
220
220
220
125
125
125
110
110
110
80
80
80
45
45
45
40
40
40
80
80
80
M 1260
M 1260
M 1265
M 16
M 16
M 16
220
220
220
SNL 515-612
SNL 516-613
SNL 517
220
220
220
125
125
125
110
110
110
80
80
80
45
45
45
40
40
40
80
80
80
M 1265
M 1270
M 1280
M 16
M 20
M 20
220
430
430
SNL 518-615
SNL 519-616
SNL 520-617
400
400
620
230
230
360
200
200
310
170
170
260
100
100
150
85
85
130
150
150
200
M 1690
M 1690
M 20100
M 20
M 20
M 24
430
430
750
SNL 522-619
SNL 524-620
SNL 526
620
620
900
360
360
500
310
310
450
260
260
380
150
150
220
130
130
190
200
200
350
M 20100
M 20110
M 24130
M 24
M 24
M 24
750
750
750
SNL 528
SNL 530
SNL 532
900
900
900
500
500
500
450
450
450
380
380
380
220
220
220
190
190
190
350
350
350
M 24130
M 24130
M 24130
M 30
M 30
M 30
1 400
1 400
1 400
1)
2)
kN
Tightening
torque
lbs = kN x 225
1 Nm = 8.85 in-lbf
461

SNL plummer block housings
for bearings on adapter sleeve
da 20 35 mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
Taconite seals
ND-design
Note: These products are not sold as complete units. Each component must be ordered separately.
Shaft
Housing
dimensions
N
N1 G
End cover
mm
mm
20
67 46 74
40 19 130 165 20 15 12
1.45
SNL 505
SNL 505
SNL 505
SNL 505
SNL 505
TSN 505 G
TSN 505 A
TSN 505 C
TSN 505 S
TSN 505 ND
ASNH 505
ASNH 505
ASNH 505
ASNH 505
ASNH 505
77 52 89
50 22 150 185 20 15 12
2.00
SNL 506-605
SNL 506-605
SNL 506-605
SNL 506-605
SNL 506-605
TSN 605 G
TSN 605 A
TSN 605 C
TSN 605 S
TSN 605 ND
ASNH 506-605
ASNH 506-605
ASNH 506-605
ASNH 506-605
ASNH 506-605
77 52 89
50 22 150 185 20 15 12
2.00
SNL 506-605
SNL 506-605
SNL 506-605
SNL 506-605
SNL 506-605
TSN 506 G
TSN 506 A
TSN 506 C
TSN 506 S
TSN 506 ND
ASNH 506-605
ASNH 506-605
ASNH 506-605
ASNH 506-605
ASNH 506-605
82 52 93
50 22 150 185 20 15 12
2.20
SNL 507-606
SNL 507-606
SNL 507-606
SNL 507-606
SNL 507-606
TSN 606 G
TSN 606 A
TSN 606 C
TSN 606 S
TSN 606 ND
ASNH 507-606
ASNH 507-606
ASNH 507-606
ASNH 507-606
ASNH 507-606
82 52 93
50 22 150 185 20 15 12
2.20
SNL 507-606
SNL 507-606
SNL 507-606
SNL 507-606
SNL 507-606
TSN 507 G
TSN 507 A
TSN 507 C
TSN 507 S
TSN 507 ND
ASNH 507-606
ASNH 507-606
ASNH 507-606
ASNH 507-606
ASNH 507-606
85 60 107 60 25 170 205 20 15 12
2.90
SNL 508-607
SNL 508-607
SNL 508-607
SNL 508-607
SNL 508-607
TSN 607 G
TSN 607 A
TSN 607 C
TSN 607 S
TSN 607 ND
ASNH 508-607
ASNH 508-607
ASNH 508-607
ASNH 508-607
ASNH 508-607
85 60 108 60 25 170 205 20 15 12
2.90
SNL 508-607
SNL 508-607
SNL 508-607
SNL 508-607
SNL 508-607
TSN 508 G
TSN 508 A
TSN 508 C
TSN 508 S
TSN 508 ND
ASNH 508-607
ASNH 508-607
ASNH 508-607
ASNH 508-607
ASNH 508-607
90 60 113 60 25 170 205 20 15 12
3.20
SNL 510-608
SNL 510-608
SNL 510-608
SNL 510-608
SNL 510-608
TSN 608 G
TSN 608 A
TSN 608 C
TSN 608 S
TSN 608 ND
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
35
Seals
30
H1 H2 J
Designations
Components
Housing
only
da
25
A1 H
Mass
kg
462

da 20 35 mm
A1
N1
H2
J
L
Shaft
Bearing
seating
Appropriate bearings and associated components

Self-aligning ball bearing
Adapter
Locating rings
Spherical roller bearing
sleeve
2 per housing
mm

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
da
Ca
mm
mm
20
25
52
80
130
1205 EK
H 205
FRB 5/52
2205 EK
22205 CCK/W33
C 2205 K
H 305
H 305
H 305 E
FRB 3.5/52
FRB 3.5/52
FRB 3.5/52
32
62
89
135
1305 EK
H 305
FRB 7.5/62
2305 EK
H 2305
FRB 4/62
32
62
89
140
1206 EK
H 206
FRB 8/62
2206 EK
22206 CCK/W33
C 2206 K
H 306
H 306
H 306 E
FRB 6/62
FRB 6/62
FRB 6/62
34
72
94
140
1306 EK
H 306
FRB 7.5/72
2306 K
H 2306
FRB 3.5/72
34
72
94
145
1207 EK
H 207
FRB 8.5/72
2207 EK
22207 CCK/W33
C 2207 K
H 307
H 307
H 307 E
FRB 5.5/72
FRB 5.5/72
FRB 5.5/72
39
80
97
145
1307 EK
H 307
FRB 9/80
2307 EK
H 2307
FRB 4/80
39
80
97
150
1208 EK
H 208
FRB 10.5/80
2208 EK
22208 EK
C 2208 K
H 308
H 308
H 308 E
FRB 8/80
FRB 8/80
FRB 8/80
41
90
102 150
1308 EK
21308 CCK
H 308
H 308
FRB 9/90
FRB 9/90
2308 EK
22308 CCK/W33
H 2308
H 2308
FRB 4/90
FRB 4/90
25
30
35
Da
Width
across
seal
A2
A3
463

da 40 50 mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
A4*
Taconite seals
ND-design
Oil seals
U-design
Shaft
Housing
dimensions
J
N1 G
Seals
End cover
mm
mm
40
85
60 109 60 25
170 205 20 15 12
2.90
SNL 509
SNL 509
SNL 509
SNL 509
SNL 509
TSN 509 G
TSN 509 A
TSN 509 C
TSN 509 S
TSN 509 ND
ASNH 509
ASNH 509
ASNH 509
ASNH 509
ASNH 509
95
70 127 70 28
210 255 24 18 16
4.40
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609 RU
TSN 609 G
TSN 609 A
TSN 609 C
TSN 609 S
TSN 609 ND
TSN 609 U
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609 R
90
60 113 60 25
170 205 20 15 12
3.20
SNL 510-608
SNL 510-608
SNL 510-608
SNL 510-608
SNL 510-608
TSN 510 G
TSN 510 A
TSN 510 C
TSN 510 S
TSN 510 ND
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
105 70 133 70 30
210 255 24 18 16
5.10
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610 RU
TSN 610 G
TSN 610 A
TSN 610 C
TSN 610 S
TSN 610 ND
TSN 610 U
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610 R
95
70 128 70 28
210 255 24 18 16
4.40
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609
SNL 211 RU
TSN 511 G
TSN 511 A
TSN 511 C
TSN 511 S
TSN 511 ND
TSN 511 U
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 513-611 R
110 80 148 80 30
230 275 24 18 16
6.50
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611 RU
TSN 611 G
TSN 611 A
TSN 611 C
TSN 611 S
TSN 611 ND
TSN 611 U
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611 R
50
H1 H2
Designations
Components
Housing
only
da
45
A1 H
Mass
kg
* For A4 dimension see Table 4, page 450.
464

da 40 50 mm
A1
N1
H2
J
L
Shaft
Bearing
seating

Adapter
Locating rings
sleeve
2 per housing
mm
da
Ca
mm
mm
40
30
85
97
44
100
41
45
50
Da
Width
across
seal
A2
A3
150

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
1209 EK
H 209
FRB 5.5/85
2209 EK
22209 CCK/W33
C 2209 K
H 309
FRB 3.5/85
H 309
FRB 3.5/85
H 309 E FRB 3.5/85
107 155
1309 EK
21309 EK
H 309
H 309
FRB 9.5/100
FRB 9.5/100
2309 EK
22309 CCK/W33
H 2309
H 2309
90
102 155
1210 EK
H 210
FRB 10.5/90
2210 EK
22210 CCK/W33
C 2210 K
H 310
FRB 9/90
H 310
FRB 9/90
H 310 E FRB 9/90
48
110
117 165
1310 EK
21310 EK
H 310
H 310
FRB 10.5/110
FRB 10.5/110
2310 K
22310 CCK/W33
H 2310
H 2310
44
100
107 165
1211 EK
H 211
FRB 11.5/100
2211 EK
H 311
22211 EK
C 2211 K
51
120
122 170
1311 EK
21311 EK
H 311
H 311
FRB 11/120
FRB 11/120
2311 K
22311 EK
FRB 4/100
FRB 4/100
FRB 4/110
FRB 4/110
FRB
9.5/100
H 311
FRB
9.5/100
H 311 E FRB
9.5/100
H 2311
H 2311
FRB 4/120
FRB 4/120
465

da 55 65 mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
A4*
Taconite seals
ND-design
Oil seals
U-design
Shaft
Housing
dimensions
H1
H2
N1
End cover
mm
mm
55
105 70 134 70 30
210 255 24 18 16
5.10
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610
SNL 212 RU
TSN 512 G
TSN 512 A
TSN 512 C
TSN 512 S
TSN 512 ND
TSN 512 U
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 515-612 R
115 80 154 80 30
230 280 24 18 16
7.00
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612 RU
TSN 612 G
TSN 612 A
TSN 612 C
TSN 612 S
TSN 612 ND
TSN 612 U
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612 R
kg
110 80
149 80
30
230 275 24 18
16
6.50
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611
SNL 213 RU
TSN 513 G
TSN 513 A
TSN 513 C
TSN 513 S
TSN 513 ND
TSN 513 U
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611 R
120 90
175 95
32
260 315 28 22
20
9.50
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613 RU
TSN 613 G
TSN 613 A
TSN 613 C
TSN 613 S
TSN 613 ND
TSN 613 U
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613 R
115 80
155 80
30
230 280 24 18
16
7.00
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612
SNL 215 RU
TSN 515 G
TSN 515 A
TSN 515 C
TSN 515 S
TSN 515 ND
TSN 515 U
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 518-615 R
140 100 193 100 35
290 345 28 22
20
12.5
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615 RU
TSN 615 G
TSN 615 A
TSN 615 C
TSN 615 S
TSN 615 ND
TSN 615 U
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615 R
466
Seals
65
Designations
Components
Housing
only
da
60
A1
Mass

da 55 65 mm
A1
N1
H2
J
L
Shaft
Bearing
seating

Adapter
Locating rings
sleeve
2 per housing
mm

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
da
Ca
mm
mm
55
48
110
117 175
1212 EK
H 212
FRB 13/110
2212 EK
22212 EK
C 2212 K
H 312
H 312
H 312 E
FRB 10/110
FRB 10/110
FRB 10/110
56
130
127 175
1312 EK
21312 EK
H 312
H 312
FRB 12.5/130
FRB 12.5/130
2312 K
22312 EK
H 2312
H 2312
FRB 5/130
FRB 5/130
60
65
Da
Width
across
seal
A2
A3
51
120
122 180
1213 EK
H 213
FRB 14/120
2213 EK
22213 CCK/W33
C 2213 K
H 313
H 313
H 313 E
FRB 10/120
FRB 10/120
FRB 10/120
58
140
138 180
1313 EK
21313 EK
H 313
H 313
FRB 12.5/140
FRB 12.5/140
2313 K
22313 EK
H 2313
H 2313
FRB 5/140
FRB 5/140
56
130
127 175
1215 K
H 215
FRB 15.5/130
2215 EK
22215 EK
C 2215 K
H 315
H 315
H 315 E
FRB 12.5/130
FRB 12.5/130
FRB 12.5/130
65
160
158 200
1315 K
21315 EK
H 315
H 315
FRB 14/160
FRB 14/160
2315 K
22315 EK
C 2315 K
H 2315
H 2315
H 2315
FRB 5/160
FRB 5/160
FRB 5/160
467

da 70 85mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
A4*
Taconite seals
ND-design
Oil seals
U-design
Shaft
Housing
dimensions
da
A1
mm
mm
70
120 90
Mass
H1
H2
N1
Designations
Components
Housing
only
Seals
End cover
kg
32
260 315 28 22
20
9.50
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613
SNL 216 RU
TSN 516 G
TSN 516 A
TSN 516 C
TSN 516 S
TSN 516 ND
TSN 516 U
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 216 R
145 100 210 112 35
290 345 28 22
20
13.7
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616 RU
TSN 616 G
TSN 616 A
TSN 616 C
TSN 616 S
TSN 616 ND
TSN 616 U
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616 R
125 90
32
260 320 28 22
20
10.0
SNL 517
SNL 517
SNL 517
SNL 517
SNL 517
SNL 217 RU
TSN 517 G
TSN 517 A
TSN 517 C
TSN 517 S
TSN 517 ND
TSN 517 U
ASNH 517
ASNH 517
ASNH 517
ASNH 517
ASNH 517
ASNH 217 R
160 110 215 112 40
320 380 32 26
24
17.6
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617 RU
TSN 617 G
TSN 617 A
TSN 617 C
TSN 617 S
TSN 617 ND
TSN 617 U
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617 R
80
140 100 194 100 35
290 345 28 22
20
12.5
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615
SNL 218 RU
TSN 518 G
TSN 518 A
TSN 518 C
TSN 518 S
TSN 518 ND
TSN 518 U
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 218 R
85
145 100 212 112 35
290 345 28 22
20
13.7
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616 RU
TSN 519 G
TSN 519 A
TSN 519 C
TSN 519 S
TSN 519 ND
TSN 519 U
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616 R
175 120 239 125 45
350 410 32 26
24
22.0
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619 RU
TSN 619 G
TSN 619 A
TSN 619 C
TSN 619 S
TSN 619 ND
TSN 619 U
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619 R
75
177 95
183 95

468

da 70 85 mm
A1
N1
H2
J
L
Shaft
Bearing
seating

Self-aligning ball bearing Adapter Locating rings
sleeve
2 per housing
mm

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
da
Ca
mm
mm
70
58
140
138 205
1216 K
H 216
FRB 16/140
2216 EK
22216 EK
C 2216 K
H 316
H 316
H 316 E
FRB 12.5/140
FRB 12.5/140
FRB 12.5/140
68
170
163 205
1316 K
21316 EK
H 316
H 316
FRB 14.5/170
FRB 14.5/170
2316 K
22316 EK
C 2316 K
H 2316
H 2316
H 2316
FRB 5/170
FRB 5/170
FRB 5/170
61
150
143 210
1217 K
H 217
FRB 16.5/150
2217 K
22217 EK
C 2217 K
H 317
H 317
H 317 E
FRB 12.5/150
FRB 12.5/150
FRB 12.5/150
70
180
178 220
1317 K
21317 EK
H 317
H 317
FRB 14.5/180
FRB 14.5/180
2317 K
22317 EK
C 2317 K
H 2317
H 2317
H 2317
FRB 5/180
FRB 5/180
FRB 5/180
80
65
160 158
225
1218 K
22218 EK
H 218
H 318
FRB 17.5/160
FRB 12.5/160
2218 K
23218 CCK/W33
C 2218 K
H 318
H 2318
H 318 E
FRB 12.5/160
FRB 6.25/160
FRB 12.5/160
85
68
170 163
220
1219 K
H 219
FRB 18/170
2219 K
22219 EK
H 319
H 319
FRB 12.5/170
FRB 12.5/170
80
200 191
235
1319 K
21319 EK
H 319
H 319
FRB 17.5/200
FRB 17.5/200
2319 K
22319 EK
H 2319
H 2319
FRB 6.5/200
FRB 6.5/200
75
Da
Width
across
seal
A2
A3
469

da 90 135 mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
A4*
Taconite seals
ND-design
Oil seals
U-design
Shaft
Housing
dimensions
A1
Mass
H1
H2
N1
Seals
End cover
da
mm
mm
90
160 110 218 112 40
320 380 32 26
24
17.6
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617 RU
TSN 520 G
TSN 520 A
TSN 520 C
TSN 520 S
TSN 520 ND
TSN 520 U
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617 R
185 120 271 140 45
350 410 32 26
24
26.2
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620 RU
TSN 620 G
TSN 620 A
TSN 620 C
TSN 620 S
TSN 620 ND
TSN 620 U
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620 R
100
175 120 242 125 45
350 410 32 26
24
22.0
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619 RU
TSN 522 G
TSN 522 A
TSN 522 C
TSN 522 S
TSN 522 ND
TSN 522 U
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619 R
110
185 120 271 140 45
350 410 32 26
24
26.2
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620 RU
TSN 524 G
TSN 524 A
TSN 524 C
TSN 524 S
TSN 524 ND
TSN 524 U
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620 R
115
190 130 290 150 50
380 445 35 28
24
33.0
SNL 526
SNL 526
SNL 526
SNL 526
SNL 526
SNL 526 RU
TSN 526 G
TSN 526 A
TSN 526 C
TSN 526 S
TSN 526 ND
TSN 526 U
ASNH 526
ASNH 526
ASNH 526
ASNH 526
ASNH 526
ASNH 526 R
125
205 150 302 150 50 420 500 42 35 30
40.0
SNL 528
SNL 528
SNL 528
SNL 528
SNL 528
SNL 528 RU
TSN 528 G
TSN 528 A
TSN 528 C
TSN 528 S
TSN 528 ND
TSN 528 U
ASNH 528
ASNH 528
ASNH 528
ASNH 528
ASNH 528
ASNH 528 R
135
220 160 323 160 60 450 530 42 35 30
49.0
SNL 530
SNL 530
SNL 530
SNL 530
SNL 530
SNL 530 RU
TSN 530 G
TSN 530 A
TSN 530 C
TSN 530 S
TSN 530 ND
TSN 530 U
ASNH 530
ASNH 530
ASNH 530
ASNH 530
ASNH 530
ASNH 530 R
kg

470
Designations
Components
Housing
only

da 90 135 mm
A1
N1
H2
J
L
Shaft
Bearing
seating
Da
Width
across
seal
A2
A3

Adapter
Locating rings
sleeve
2 per housing
mm

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
da
Ca
mm
mm
90
70
180 178
235
1220 K
22220 EK
H 220
H 320
FRB 18/180
FRB 12/180
2220 K
23220 CCK/W33
C 2220 K
H 320
H 2320
H 320 E
FRB 12/180
FRB 4.85/180
FRB 12/180
86
215 199
240
1320 K
21320 EK
H 320
H 320
FRB 19.5/215
FRB 19.5/215
2320 K
22320 EK
C 2320 K
H 2320
H 2320
H 2320
FRB 6.5/215
FRB 6.5/215
FRB 6.5/215
100
80
200 191
250
1222 K
22222 EK
H 222
H 322
FRB 21/200
FRB 13.5/200
2222 K
23222 CCK/W33
C 2222 K
H 322
H 2322
H 322 E
FRB 13.5/200
FRB 5.1/200
FRB 13.5/200
110
86
215 199
260
1224 K
22224 EK
H 3124
H 3124
FRB 22/215
FRB 14/215
23224 CCK/W33
C 3224 K
H 2324
FRB 5/215
H 2324 L FRB 5/215
115
90
230 208
265
22226 EK
H 3126
FRB 13/230
23226 CCK/W33
C 2226 K
H 2326
FRB 5/230
H 3126 L FRB 13/230
125
98
250 223
285
22228 CCK/W33
H 3128
FRB 15/250
23228 CCK/W33
C 2228 K
H 2328
FRB 5/250
H 3128 L FRB 15/250
135
106 270 241
295
22230 CCK/W33
H 3130
FRB 16.5/270
23230 CCK/W33
C 2230 K
H 2330
FRB 5/270
H 3130 L FRB 16.5/270
471

da 140 mm
Ca
Da da
H1
A3
A2
Labyrinth seals
S-design
Double-lip seals
G-design
A4*
Taconite seals
ND-design
Oil seals
U-design
Shaft
Housing
dimensions
A1
Mass
da
H1
H2 J
N1
mm
mm
140
235 160 344 170 60 470 550 42 35
472
Designations
Components
Housing
only
Seals
End cover
SNL 532
SNL 532
SNL 532
SNL 532
SNL 532
SNL 532 RU
TSN 532 G
TSN 532 A
TSN 532 C
TSN 532 S
TSN 532 ND
TSN 532 U
ASNH 532
ASNH 532
ASNH 532
ASNH 532
ASNH 532
ASNH 532 R
kg
30
55.0

da 140 mm
A1
N1
H2
J
L
Shaft
Bearing
seating
Da
Width
across
seal
A2
A3

Adapter
Locating rings
sleeve
2 per housing
mm
da
Ca
mm
mm
140
114 290 254
315
22232 CCK/W33
H 3132
FRB 17/290

CARB bearing
Adapter
sleeve
Locating
rings
2 per
housing
23232 CCK/W33
C 3232 K
H 2332
FRB 5/290
H 2332 L FRB 5/290
473

for bearings with cylindrical bore
da 25 40 mm
Ca
Da db
da
H1
Double-lip seals
G-design
A2
A3
Labyrinth seals
S-design
Taconite seals
ND-design
Shaft
Housing
dimensions
L
N1
mm
25
67
46
74
40
19 130 165 20 15 12
1.40
SNL 205
SNL 505
SNL 205
SNL 205
TSN 205 G
2 FS 170
TSN 205 S
TSN 205 ND
ASNH 506-605
ASNH 505
ASNH 506-605
ASNH 506-605
77
52
89
50
22 150 185 20 15 12
1.90
SNL 206-305
SNL 206-305
SNL 206-305
SNL 206-305
TSN 305 G
TSN 305 A
TSN 305 S
TSN 305 ND
ASNH 507-605
ASNH 507-605
ASNH 507-605
ASNH 507-605
77
52
89
50
22 150 185 20 15 12
1.90
SNL 206-305
SNL 206-305
SNL 506-605
SNL 206-305
SNL 206-305
TSN 206 G
TSN 206 A
2 FS 170
TSN 206 S
TSN 206 ND
ASNH 507-606
ASNH 507-606
ASNH 506-605
ASNH 507-606
ASNH 507-606
82
52
93
50
22 150 185 20 15 12
2.20
SNL 507-606
SNL 507-606
SNL 507-606
SNL 507-606
TSN 306 G
TSN 306 A
TSN 306 S
TSN 306 ND
ASNH 507-606
ASNH 507-606
ASNH 507-606
ASNH 507-606
82
52
93
50
22 150 185 20 15 12
2.10
SNL 207
SNL 207
SNL 507-606
SNL 207
SNL 207
TSN 207 G
TSN 207 A
4 FS 170
TSN 207 S
TSN 207 ND
ASNH 509
ASNH 509
ASNH 507-606
ASNH 509
ASNH 509
85
60
108 60
25 170 205 20 15 12
2.90
SNL 208-307
SNL 208-307
SNL 208-307
SNL 208-307
TSN 307 G
TSN 307 A
TSN 307 S
TSN 307 ND
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
85
60
108 60
25 170 205 20 15 12
2.75
SNL 208-307
SNL 208-307
SNL 508-607
SNL 208-307
SNL 208-307
TSN 208 G
TSN 208 A
4 FS 170
TSN 208 S
TSN 208 ND
ASNH 510-608
ASNH 510-608
ASNH 508-607
ASNH 510-608
ASNH 510-608
90
60
113 60
25 170 205 20 15 12
3.20
SNL 510-608
SNL 510-608
SNL 510-608
SNL 510-608
TSN 308 G
TSN 308 A
TSN 308 S
TSN 308 ND
ASNH 510-608
ASNH 510-608
ASNH 510-608
ASNH 510-608
kg
For seal details see pages 484 - 487.
474
End cover
mm
40
H1 H2 J
Seals
35
Designations
Components
Housing
only
da
30
A1
Mass

da 25 40 mm
A1
N1
H2
J
L
Shaft
da
Bearing
seating
db
mm
25
30
35
40
Ca
Da
mm
Width
across
seal
A2
A3
Appropriate bearings and locating rings

Locating rings
2 per housing
mm

CARB bearing
Locating rings
2 per housing
30
25
52
90
140
1205 E
FRB 5/52
2205 E
22205 CC/W33
C 2205
FRB 3.5/52
FRB 3.5/52
FRB 3.5/52
30
32
62
89
150
1305 E
21305 CC
FRB 7.5/62
FRB 7.5/62
2305
FRB 4/62
35
32
62
89
150
1206 E
FRB 8/62
2206 E
22206 CC/W33
C 2206
FRB 6/62
FRB 6/62
FRB 6/62
35
34
72
94
155
1306 E
21306 CC
FRB 7.5/72
FRB 7.5/72
2306
FRB 3.5/72
45
34
72
96
155
1207 E
FRB 8.5/72
2207 E
22207 CC/W33
C 2207
FRB 5.5/72
FRB 5.5/72
FRB 5.5/72
45
39
80
99
164
1307 E
21307 CC
FRB 9/80
FRB 9/80
2307 E
FRB 4/80
50
39
80
99
160
1208 E
FRB 10.5/80
2208 E
22208 E
C 2208
FRB 8/80
FRB 8/80
FRB 8/80
50
41
90
102
167
1308 E
21308 E
FRB 9/90
FRB 9/90
2308 E
22308 CC/W33
FRB 4/90
FRB 4/90
475

da 45 60 mm
Ca
Da db
da
H1
A2
Double-lip seals
G-design
Labyrinth seals
S-design
A4*
A3
Taconite seals
ND-design
Oil seals
U-design
Shaft Housing
dimensions
H2
N1 G
End cover
mm
mm
45
85
60 109
60 25 170 205 20 15 12
2.75
SNL 209
SNL 209
SNL 509
SNL 209
SNL 209
TSN 209 G
TSN 209 A
4 FS 170
TSN 209 S
TSN 209 ND
ASNH 511-609
ASNH 511-609
ASNH 509
ASNH 511-609
ASNH 511-609
95
70 128
70 28 210 255 24 18 16
4.40
SNL 511-609
SNL 511-609
SNL 511-609
SNL 511-609
TSN 309 G
TSN 309 A
TSN 309 S
TSN 309 ND
ASNH 511-609
ASNH 511-609
ASNH 511-609
ASNH 511-609
90
60 113
60 25 170 205 20 15 12
3.00
SNL 210
SNL 210
SNL 510-608
SNL 210
SNL 210
TSN 210 G
TSN 210 A
4 FS 170
TSN 210 S
TSN 210 ND
ASNH 512-610
ASNH 512-610
ASNH 510-608
ASNH 512-610
ASNH 512-610
105 70 134
70 30 210 255 24 18 16
5.10
SNL 512-610
SNL 512-610
SNL 512-610
SNL 512-610
TSN 310 G
TSN 310 A
TSN 310 S
TSN 310 ND
ASNH 512-610
ASNH 512-610
ASNH 512-610
ASNH 512-610
95
70 128
70 28 210 255 24 18 16
4.20
SNL 211
SNL 211
SNL 511-609
SNL 211
SNL 211
TSN 211 G
TSN 211 A
4 FS 170
TSN 211 S
TSN 211 ND
ASNH 513-611
ASNH 513-611
ASNH 511-609
ASNH 513-611
ASNH 513-611
110 80 149
80 30 230 275 24 18 16
6.50
SNL 513-611
SNL 513-611
SNL 513-611
SNL 513-611
TSN 311 G
TSN 311 A
TSN 311 S
TSN 311 ND
ASNH 513-611
ASNH 513-611
ASNH 513-611
ASNH 513-611
105 70 134
70 30 210 255 24 18 16
4.75
SNL 212
SNL 212
SNL 512-610
SNL 212
SNL 212
TSN 212 G
TSN 212 A
4 FS 170
TSN 212 S
TSN 212 ND
ASNH 515-612
ASNH 515-612
ASNH 512-610
ASNH 515-612
ASNH 515-612
115 80 155
80 30 230 280 24 18 16
7.00
SNL 515-612
SNL 515-612
SNL 515-612
SNL 515-612
SNL 215 RU
TSN 312 G
TSN 312 A
TSN 312 S
TSN 312 ND
TSN 312 U
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 515-612
ASNH 518-615 R
60
H1
Seals
55
Designations
Components
Housing
only
da
50
A1
Mass
kg

476

da 45 60 mm
A1
N1
H2
J
L
Shaft
da
Bearing
seating
db
mm
45
50
55
60
Ca
Da
mm
Width
across
seal
A2
A3

Locating rings
2 per housing
mm

CARB bearing
Locating rings
2 per housing
55
30
85
97
160
1209 E
FRB 5.5/85
2209 E
22209 CC/W33
C 2209
FRB 3.5/85
FRB 3.5/85
FRB 3.5/85
55
44
100
107
172
1309 E
21309 E
FRB 9.5/100
FRB 9.5/100
2309 E
22309 CC/W33
FRB 4/100
FRB 4/100
60
41
90
102
165
1210 E
FRB 10.5/90
2210 E
22210 CC/W33
C 2210
FRB 9/90
FRB 9/90
FRB 9/90
60
48
110
117
187
1310 E
21310 E
FRB 10.5/110
FRB 10.5/110
2310
22310 CC/W33
FRB 4/110
FRB 4/110
65
44
100
107
170
1211 E
FRB 11.5/100
2211 E
22211 E
C 2211
FRB 9.5/100
FRB 9.5/100
FRB 9.5/100
65
51
120
122
192
1311 E
21311 E
FRB 11/120
FRB 11/120
2311
22311 E
FRB 4/120
FRB 4/120
70
48
110
117
180
1212 E
FRB 13/110
2212 E
22212 E
C 2212
FRB 10/110
FRB 10/110
FRB 10/110
70
56
130
127
197
1312
21312 E
FRB 12.5/130
FRB 12.5/130
2312
22312 E
FRB 5/130
FRB 5/130
477

da 65 80 mm
Ca
Da db
da
H1
A2
Double-lip seals
G-design
Labyrinth seals
S-design
A4*
A3
Taconite seals
ND-design
Oil seals
U-design
Shaft Housing
dimensions
H
H1
H2
N1 G
Designations
Components
Housing
only
Seals
End cover
da
mm
mm
65
110 80
149 80
30
230 275 24
18 16
6.10
SNL 213
SNL 213
SNL 513-611
SNL 213
SNL 213
TSN 213 G
TSN 213 A
4 FS 170
TSN 213 S
TSN 213 ND
ASNH 516-613
ASNH 516-613
ASNH 513-611
ASNH 516-613
ASNH 516-613
120 90
177 95
32
260 315 28
22 20
9.50
SNL 516-613
SNL 516-613
SNL 516-613
SNL 516-613
SNL 216 RU
TSN 313 G
TSN 313 A
TSN 313 S
TSN 313 ND
TSN 313 U
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 516-613
ASNH 216 R
70
125 90
183 95
32
260 320 28
22 20
10.0
SNL 517
SNL 517
SNL 517
SNL 517
SNL 217 RU
TSN 314 G
TSN 314 A
TSN 314 S
TSN 314 ND
TSN 314 U
ASNH 517
ASNH 517
ASNH 517
ASNH 517
ASNH 217 R
75
115 80
155 80
30
230 280 24
18 16
6.60
SNL 215
SNL 215
SNL 515-612
SNL 215
SNL 215
TSN 215 G
TSN 215 A
4 FS 170
TSN 215 S
TSN 215 ND
ASNH 518-615
ASNH 518-615
ASNH 515-612
ASNH 518-615
ASNH 518-615
140 100 194 100 35
290 345 28
22 20
12.5
SNL 518-615
SNL 518-615
SNL 518-615
SNL 518-615
SNL 218 RU
TSN 315 G
TSN 315 A
TSN 315 S
TSN 315 ND
TSN 315 U
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 518-615
ASNH 218 R
120 90
32
260 315 28
22 20
9.00
SNL 216
SNL 216
SNL 516-613
SNL 216
SNL 216
TSN 216 G
TSN 216 A
4 FS 170
TSN 216 S
TSN 216 ND
ASNH 216
ASNH 216
ASNH 516-613
ASNH 216
ASNH 216
145 100 212 112 35
290 345 28
22 20
13.7
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616
SNL 519-616 RU
TSN 316 G
TSN 316 A
TSN 316 S
TSN 316 ND
TSN 316 U
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616
ASNH 519-616 R
80
A1
Mass
kg
177 95

478

da 65 80 mm
A1
N1
H2
J
L
Shaft
da
Bearing
seating
db
mm
65
Ca
Da
mm
Width
across
seal
A2
A3

Locating rings
2 per housing
mm

CARB bearing
Locating rings
2 per housing
75
51
120
128
190
1213 E
FRB 14/120
2213 E
22213 CC/W33
C 2213
FRB 10/120
FRB 10/120
FRB 10/120
75
58
140
138
200
1313 E
21313 E
FRB 12.5/140
FRB 12.5/140
2313
22313 E
FRB 5/140
FRB 5/140
70
80
61
150
143
205
1314
21314 E
FRB 13/150
FRB 13/150
2314
22314 E
C 2314
FRB 5/150
FRB 5/150
FRB 5/150
75
85
56
130
133
195
1215
FRB 15.5/130
2215 E
22215 E
C 2215
FRB 12.5/130
FRB 12.5/130
FRB 12.5/130
85
65
160
158
220
1315
21315 E
FRB 14/160
FRB 14/160
2315
22315 E
C 2315
FRB 5/160
FRB 5/160
FRB 5/160
90
58
140
138
200
1216
FRB 16/140
2216 E
22216 E
C 2216
FRB 12.5/140
FRB 12.5/140
FRB 12.5/140
90
68
170
163
205
1316
21316 E
FRB 14.5/170
FRB 14.5/170
2316
22316 E
C 2316
FRB 5/170
FRB 5/170
FRB 5/170
80
479

da 85 130 mm
Ca
Da db
da
H1
A2
Double-lip seals
G-design
Labyrinth seals
S-design
A4*
A3
Taconite seals
ND-design
Oil seals
U-design
Shaft Housing
dimensions
da
A1
mm
mm
85
125 90
Mass
H1
H2
N1 G
Designations
Components
Housing
only
Seals
End cover
kg
183 95
32
260 320 28
22 20
9.50
SNL 217
SNL 217
SNL 517
SNL 217
SNL 217
TSN 217 G
TSN 217 A
4 FS 170
TSN 217 S
TSN 217 ND
ASNH 217
ASNH 217
ASNH 517
ASNH 217
ASNH 217
160 110 218 112 40
320 380 32
26 24
17.6
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617 RU
TSN 317 G
TSN 317 A
TSN 317 S
TSN 317 ND
TSN 317 U
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617 R
90
140 100 194 100 35
290 345 28
22 20
11.8
SNL 218
SNL 218
SNL 518-615
SNL 218
SNL 218
TSN 218 G
TSN 218 A
4 FS 170
TSN 218 S
TSN 218 ND
ASNH 218
ASNH 218
ASNH 518-615
ASNH 218
ASNH 218
95
175 120 242 125 45
350 410 32
26 24
22.0
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619 RU
TSN 319 A
TSN 319 S
TSN 319 ND
TSN 319 U
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619 R
100
160 110 218 112 40
320 380 32
26 24
17.6
SNL 520-617
SNL 520-617
SNL 520-617
SNL 520-617
TSN 220 G
TSN 220 A
TSN 220 S
TSN 220 ND
ASNH 520-617
ASNH 520-617
ASNH 520-617
ASNH 520-617
185 120 271 140 45
350 410 32
26 24
26.2
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620 RU
TSN 320 A
TSN 320 S
TSN 320 ND
TSN 320 U
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620 R
110
175 120 242 125 45
350 410 32
26 24
22.0
SNL 522-619
SNL 522-619
SNL 522-619
SNL 522-619
TSN 222 G
TSN 222 A
TSN 222 S
TSN 222 ND
ASNH 522-619
ASNH 522-619
ASNH 522-619
ASNH 522-619
120
185 120 271 140 45
350 410 32
26 24
26.2
SNL 524-620
SNL 524-620
SNL 524-620
SNL 524-620
TSN 224 G
TSN 224 A
TSN 224 S
TSN 224 ND
ASNH 524-620
ASNH 524-620
ASNH 524-620
ASNH 524-620
130
190 130 290 150 50
380 445 35
28 24
33.0
SNL 526
SNL 526
SNL 526
SNL 526
TSN 226 G
TSN 226 A
TSN 226 S
TSN 226 ND
ASNH 526
ASNH 526
ASNH 526
ASNH 526
480

da 85 130 mm
A1
N1
H2
J
L
Shaft
da
Bearing
seating
db
mm
85
Ca
Da
mm
Width
across
seal
A2
A3

Locating rings
2 per housing
mm

CARB bearing
Locating rings
2 per housing
95
61
150
143
205
1217
FRB 16.5/150
2217
22217 E
C 2217
FRB 12.5/150
FRB 12.5/150
FRB 12.5/150
95
70
180
178
220
1317
21317 E
FRB 14.5/180
FRB 14.5/180
2317
22317 E
C 2317
FRB 5/180
FRB 5/180
FRB 5/180
90
100
65
160
158
220
1218
22218 E
FRB 17.5/160
FRB 12.5/160
2218
23218 CC/W33
C 2218
FRB 12.5/160
FRB 6.25/160
FRB 12.5/160
95
110
80
200
191
235
1319
21319 E
FRB 17.5/200
FRB 17.5/200
2319
22319 E
FRB 6.5/200
FRB 6.5/200
100
115
70
180
178
240
1220
22220 E
FRB 18/180
FRB 12/180
2220
23220 CC/W33
C 2220
FRB 12/180
FRB 4.85/180
FRB 12/180
115
86
215
199
240
1320
21320 E
FRB 19.5/215
FRB 19.5/215
2320
22320 E
C 2320
FRB 6.5/215
FRB 6.5/215
FRB 6.5/215
110
125
80
200
191
255
1222
22222 E
FRB 21/200
FRB 13.5/200
2222
23222 CC/W33
C 2222
FRB 13.5/200
FRB 5.1/200
FRB 13.5/200
120
135
86
215
199
260
1224
22224 E
FRB 22/215
FRB 14/215
23224 CC/W33
C 3224
FRB 5/215
FRB 5/215
130
145
90
230
208
270
1226
22226 E
FRB 22/230
FRB 13/230
23226 CC/W33
C 2226
FRB 5/230
FRB 13/230
481

da 140 160 mm
Ca
Da db
da
H1
Double-lip seals
G-design
A2
A3
Labyrinth seals
S-design
Taconite seals
ND-design
Shaft Housing
dimensions
A1
Mass
H1
H2
N1 G
Designations
Components
Housing
only
Seals
End cover
da
mm
mm
140
205 150 302 150 50
420 500 42
35 30
40.0
SNL 528
SNL 528
SNL 528
SNL 528
TSN 228 G
TSN 228 A
TSN 228 S
TSN 228 ND
ASNH 528
ASNH 528
ASNH 528
ASNH 528
150
220 160 323 160 60
450 530 42
35 30
49.0
SNL 530
SNL 530
SNL 530
SNL 530
TSN 230 G
TSN 230 A
TSN 230 S
TSN 230 ND
ASNH 530
ASNH 530
ASNH 530
ASNH 530
160
235 160 344 170 60
470 550 42
35 30
55.0
SNL 532
SNL 532
SNL 532
SNL 532
TSN 232 G
TSN 232 A
TSN 232 S
TSN 232 ND
ASNH 532
ASNH 532
ASNH 532
ASNH 532
kg
482

da 140 160 mm
A1
N1
H2
J
L
Shaft
da
Bearing
seating
db
mm
Ca
Da
mm
Width
across
seal
A2
A3

Locating rings
2 per housing
mm

CARB bearing
Locating rings
2 per housing
140
155
98
250
223
290
22228 CC/W33
FRB 15/250
23228 CC/W33
C 2228
FRB 5/250
FRB 15/250
150
165
106
270
241
305
22230 CC/W33
FRB 16.5/270
C 2230
23230 CC/W33
FRB 16.5/270
FRB 5/270
160
175
114
290
254
320
22232 CC/W33
FRB 17/290
23232 CC/W33
C 3232
FRB 5/290
FRB 5/290
483

Sealing arrangements for
Size 505 510-608
db
da
Housing series 5
Design A
Unsplit
Design G
Split
Housing
Size
Shaft
dia.
Design C
Split
Design C
Felt Strips
Split
Design S
Unsplit
Housing series 2
Design ND
End Cover
da, db
Seal sets
Design G
2 double-lip
seals
End cover
mm
505
20
30
TSN 505 G
TSN 505 A
CR 400200
TSN 505 C
2 FS 170
2 TSN 505 S
2 TSN 505 ND
ASNH 505
205
20
25
30
35
TSN 605 G
TSN 506 G
TSN 205 G
TSN 605 A
TSN 506 A
CR 400200
CR 400250
TSN 605 C
TSN 506 C
2 FS 170
2 TSN 605 S
2 TSN 506 S
2 TSN 205 S
2 TSN 605 ND
2 TSN 506 ND
2 TSN 205 ND
ASNH 506-605
506-605
20
25
30
35
TSN 605 G
TSN 506 G
TSN 305 G
TSN 605 A
TSN 506 A
TSN 305 A
CR 400200
CR 400250
TSN 605 C
TSN 506 C
2 FS 170
2 TSN 605 S
2 TSN 506 S
2 TSN 305 S
2 TSN 605 ND
2 TSN 506 ND
2 TSN 305 ND
ASNH 506-605
206-305
25
30
35
45
TSN 606 G
TSN 507 G
TSN 206 G
TSN 606 A
TSN 507 A
TSN 206 A
CR 400250
CR 400300
CR 400350
TSN 606 C
TSN 507 C
2 FS 170
2 TSN 606 S
2 TSN 507 S
2 TSN 206 S
2 TSN 606 ND
2 TSN 507 ND
2 TSN 206 ND
ASNH 507-606
507-606
25
30
35
45
TSN 606 G
TSN 507 G
TSN 306 G
TSN 606 A
TSN 507 A
TSN 306 A
CR 400250
CR 400300
CR 400350
TSN 606 C
TSN 507 C
2 FS 170
2 TSN 606 S
2 TSN 507 S
2 TSN 306 S
2 TSN 606 ND
2 TSN 507 ND
2 TSN 306 ND
ASNH 507-606
207
40
45
55
TSN 509 G
TSN 207 G
TSN 509 A
TSN 207 A
CR 400400
CR 400450
TSN 509 C
4 FS 170
2 TSN 509 S
2 TSN 207 S
2 TSN 509 ND
2 TSN 207 ND
ASNH 509
508-607
30
35
50
TSN 607 G
TSN 508 G
TSN 607 A
TSN 508 A
CR 400300
CR 400350
TSN 607 C
TSN 508 C
4 FS 170
2 TSN 607 S
2 TSN 508 S
2 TSN 607 ND
2 TSN 508 ND
ASNH 508-607
208-307
35
45
50
60
TSN 608 G
TSN 307 G
TSN 208 G
TSN 608 A
TSN 307 A
TSN 208 A
CR 400350
CR 400450
CR 400500
TSN 608 C
4 FS 170
2 TSN 608 S
2 TSN 307 S
2 TSN 208 S
2 TSN 608 ND
2 TSN 307 ND
2 TSN 208 ND
ASNH 510-608
509
40
45
55
TSN 509 G
TSN 307 G
TSN 509 A
TSN 307 A
CR 400400
CR 400450
TSN 509 C
4 FS 170
2 TSN 509 S
2 TSN 307 S
2 TSN 509 ND
2 TSN 307 ND
ASNH 509
209
40
50
55
65
TSN 609 G
TSN 511 G
TSN 209 G
TSN 609 A
TSN 511 A
TSN 209 A
CR 400400
CR 400500
CR 400550
TSN 609 C
TSN 511 C
4 FS 170
2 TSN 609 S
2 TSN 511 S
2 TSN 209 S
2 TSN 609 ND
2 TSN 511 ND
2 TSN 209 ND
ASNH 511-609
510-608
35
45
50
60
TSN 608 G
TSN 510 G
TSN 308 G
TSN 608 A
TSN 510 A
TSN 308 A
CR 400350
CR 400450
CR 400500
TSN 608 C
TSN 510 C
4 FS 170
2 TSN 608 S
2 TSN 510 S
2 TSN 308 S
2 TSN 608 ND
2 TSN 510 ND
2 TSN 308 ND
ASNH 510-608
Design A
2 V-ring
seals
Loose
V-ring
Loose felt
strips
Design S
2 labyrinth
seals
Design ND
484
Design C
2 felt
strips

Size 210 516-613
db
da
Housing series 2
Housing series 5
Design A
Unsplit
Design G
Split
Housing
Size
Shaft
dia.
Design C
Split
Design C
Felt strips
Split
Design S
Unsplit
Design ND
End cover
da, db
Seal sets
Design G
2 double-lip
seals
End cover
mm
210
45
55
60
70
TSN 610 G
TSN 512 G
TSN 210 G
TSN 610 A
TSN 512 A
TSN 210 A
CR 400450
CR 400550
CR 400600
TSN 610 C
TSN 512 C
4 FS 170
2 TSN 610 S
2 TSN 512 S
2 TSN 210 S
2 TSN 610 ND
2 TSN 512 ND
2 TSN 210 ND
ASNH 512-610
511-609
40
50
55
65
TSN 609 G
TSN 511 G
TSN 309 G
TSN 609 A
TSN 511 A
TSN 309 A
CR 400400
CR 400500
CR 400550
TSN 609 C
TSN 511 C
4 FS 170
2 TSN 609 S
2 TSN 511 S
2 TSN 309 S
2 TSN 609 ND
2 TSN 511 ND
2 TSN 309 ND
ASNH 511-609
211
50
60
65
75
TSN 611 G
TSN 513 G
TSN 211 G
TSN 611 A
TSN 513 A
TSN 211 A
CR 400500
CR 400600
CR 400650
TSN 611 C
TSN 513 C
4 FS 170
2 TSN 611 S
2 TSN 513 S
2 TSN 211 S
2 TSN 611 ND
2 TSN 513 ND
2 TSN 211 ND
ASNH 513-611
512-610
45
55
60
70
TSN 610 G
TSN 512 G
TSN 310 G
TSN 610 A
TSN 512 A
TSN 310 A
CR 400450
CR 400550
CR 400600
TSN 610 C
TSN 512 C
4 FS 170
2 TSN 610 S
2 TSN 512 S
2 TSN 310 S
2 TSN 610 ND
2 TSN 512 ND
2 TSN 310 ND
ASNH 512-610
212
55
65
70
85
TSN 612 G
TSN 515 G
TSN 212 G
TSN 612 A
TSN 515 A
TSN 212 A
CR 400550
CR 400650
CR 400700
TSN 612 C
TSN 515 C
4 FS 170
2 TSN 612 S
2 TSN 515 S
2 TSN 212 S
2 TSN 612 ND
2 TSN 515 ND
2 TSN 212 ND
ASNH 515-612
513-611
50
60
65
75
TSN 611 G
TSN 513 G
TSN 311 G
TSN 611 A
TSN 513 A
TSN 311 A
CR 400500
CR 400600
CR 400650
TSN 611 C
TSN 513 C
4 FS 170
2 TSN 611 S
2 TSN 513 S
2 TSN 311 S
2 TSN 611 ND
2 TSN 513 ND
2 TSN 311 ND
ASNH 513-611
213
60
70
75
90
TSN 613 G
TSN 516 G
TSN 213 G
TSN 613 A
TSN 516 A
TSN 213 A
CR 400600
CR 400700
CR 400750
TSN 613 C
TSN 516 C
4 FS 170
2 TSN 613 S
2 TSN 516 S
2 TSN 213 S
2 TSN 613 ND
2 TSN 516 ND
2 TSN 213 ND
ASNH 516-613
515-612
55
65
70
85
TSN 612 G
TSN 515 G
TSN 312 G
TSN 612 A
TSN 515 A
TSN 312 A
CR 400550
CR 400650
CR 400700
TSN 612 C
TSN 515 C
4 FS 170
2 TSN 612 S
2 TSN 515 S
2 TSN 312 S
2 TSN 612 ND
2 TSN 515 ND
2 TSN 312 ND
ASNH 515-612
215
65
80
85
100
TSN 615 G
TSN 518 G
TSN 215 G
TSN 615 A
TSN 518 A
TSN 215 A
CR 400650
CR 400800
CR 400850
TSN 615 C
TSN 518 C
4 FS 170
2 TSN 615 S
2 TSN 518 S
2 TSN 215 S
2 TSN 615 ND
2 TSN 518 ND
2 TSN 215 ND
ASNH 518-615
516-613
60
70
75
90
TSN 613 G
TSN 516 G
TSN 313 G
TSN 613 A
TSN 516 A
TSN 313 A
CR 400600
CR 400700
CR 400750
TSN 613 C
TSN 516 C
4 FS 170
2 TSN 613 S
2 TSN 516 S
2 TSN 313 S
2 TSN 613 ND
2 TSN 516 ND
2 TSN 313 ND
ASNH 516-613
Design A
2 V-ring
seals
Loose
V-ring
Design C
2 felt
strips
Loose felt
strips
Design S
2 labyrinth
seals
Design ND
485

Size 216 532
db
da
Housing series 5
Housing
Size
Shaft
dia.
Design C
Split
Design A
Unsplit
Design G
Split
Design C
Felt strips
Split
Design S
Unsplit
Housing series 2
Design ND
End cover
da, db
Seal sets
Design G
2 double-lip
seals
End cover
mm
216
90
105
TSN 216 G
TSN 216 A
CR 400900
2 FS 170
2 TSN 216 S
2 TSN 216 ND
ASNH 216
517
75
80
95
TSN 517 G
TSN 314 G
TSN 517 A
TSN 314 A
CR 400750
CR 400800
TSN 517 C
TSN 314 C
2 FS 170
2 TSN 517 S
2 TSN 314 S
2 TSN 517 ND
2 TSN 314 ND
ASNH 517
217
95
TSN 217 G
TSN 217 A
CR 400950
2 TSN 217 S
2 TSN 217 ND
ASNH 217
518-615
65
80
85
100
TSN 615 G
TSN 518 G
TSN 315 G
TSN 615 A
TSN 518 A
TSN 315 A
CR 400650
CR 400800
CR 400850
TSN 615 C
TSN 518 C
2 FS 170
2 TSN 615 S
2 TSN 518 S
2 TSN 315 S
2 TSN 615 ND
2 TSN 518 ND
2 TSN 315 ND
ASNH 518-615
218
100
TSN 218 G
TSN 218 A
CR 401000
2 TSN 218 S
2 TSN 218 ND
ASNH 218
519-616
70
85
90
TSN 616 G
TSN 519 G
TSN 316 G
TSN 616 A
TSN 519 A
TSN 316 A
CR 400700
CR 400850
CR 400900
TSN 616 C
TSN 519 C
2 TSN 616 S
2 TSN 519 S
2 TSN 316 S
2 TSN 616 ND
2 TSN 519 ND
2 TSN 316 ND
ASNH 519-616
520-617
75
90
95
115
TSN 617 G
TSN 520 G
TSN 317 G
TSN 220 G
TSN 617 A
TSN 520 A
TSN 317 A
TSN 220 A
CR 400750
CR 400900
CR 400950
CR 401100
TSN 617 C
TSN 520 C
2 TSN 617 S
2 TSN 520 S
2 TSN 317 S
2 TSN 220 S
2 TSN 617 ND
2 TSN 520 ND
2 TSN 317 ND
2 TSN 220 ND
ASNH 520-617
522-619
85
100
110
125
TSN 619 G
TSN 522 G
TSN 222 G
TSN 619 A
TSN 522 A
TSN 319 A
TSN 222 A
CR 400850
CR 401000
CR 401100
CR 401300
TSN 619 C
TSN 522 C
2 TSN 619 S
2 TSN 522 S
2 TSN 319 S
2 TSN 222 S
2 TSN 619 ND
2 TSN 522 ND
2 TSN 319 ND
2 TSN 222 ND
ASNH 522-619
524-620
90
110
115
135
TSN 620 G
TSN 524 G
TSN 224 G
TSN 620 A
TSN 524 A
TSN 320 A
TSN 224 A
CR 400900
CR 401100
CR 401100
CR 401300
TSN 620 C
TSN 524 C
2 TSN 620 S
2 TSN 524 S
2 TSN 320 S
2 TSN 224 S
2 TSN 620 ND
2 TSN 524 ND
2 TSN 320 ND
2 TSN 224 ND
ASNH 524-620
526
115
145
TSN 526 G
TSN 226 G
TSN 526 A
TSN 226 A
CR 401100
CR 401500
TSN 526 C
2 TSN 526 S
2 TSN 226 S
2 TSN 526 ND
2 TSN 226 ND
ASNH 526
528
125
155
TSN 528 G
TSN 228 G
TSN 528 A
TSN 228 A
CR 401300
CR 401500
TSN 528 C
TSN 228 C
2 TSN 528 S
2 TSN 228 S
2 TSN 528 ND
2 TSN 228 ND
ASNH 528
530
135
165
TSN 530 G
TSN 230 G
TSN 530 A
TSN 230 A
CR 401300
CR 401700
TSN 530 C
2 TSN 530 S
2 TSN 230 S
2 TSN 530 ND
2 TSN 230 ND
ASNH 530
532
140
175
TSN 532 G
TSN 232 G
TSN 532 A
TSN 232 A
CR 401400
CR 401700
TSN 532 C
2 TSN 532 S
2 TSN 232 S
2 TSN 532 ND
2 TSN 232 ND
ASNH 532
Design A
2 V-ring
seals
Loose
V-ring
Loose felt
strips
Design S
2 labyrinth
seals
Design ND
486
Design C
2 felt
strips
Split pillow blocks

SNL 30 and SNL 31 (metric series)
Nomenclature
SNL D 3134 TSSN

4
2
1
1. Basic design:
4. Suffix:
SNL
Housing for bearing with adapter

sleeve and through shaft
Housing for bearing with

cylindrical bore and for
stepped shaft
Housing for shaft end,

with end cover at one side
2. Material:
Housing of gray cast-iron
TS
Housing with labyrinth seal(s)
Housing of spheroidal graphite

cast-iron (ductile-iron)
TNF
Housing with taconite seal(s)
Housing with grease escape

holes in base

at one side of cap to take
grease nipple for relubrication
of seals; nipple supplied with
housing
TD

at both sides of cap to take
grease nipple for relubrication
of seals; two nipples supplied
with housing
SN
Housing with drilled and tapped

hole for sensor
TURT
Housing prepared for oil lubrication

(spherical roller bearing) with seals
TURA
Housing prepared for oil lubrication

(CARB bearing) with seals
3. Housing size:
3036 to 30/500
3134 to 3196
487

Introduction
Fewer bearing replacements and less maintenance

Plummer (pillow) block housings have
much to offer
SNL 30 and SNL 31 plummer (pillow)

block housings have more to offer
The main benefit of split plummer block housings

is their easy installation; pre-assembled shafts
can be mounted in them. When the housing
bases are attached to the base plate it is then
only necessary to place the housing caps in
position and to tighten the attachment bolts to
complete the installation.
Split plummer block housings available on the
market are mainly intended for self-aligning ball
bearings, spherical roller bearings and CARB
toroidal roller bearings. The housings can accomodate bearings in the 02, 03, 22, 23, 30, 31,
32, 39, 40 and 41 ISO Dimension Series. They
can often be fitted with a variety of seals.
Several designs and variants of split plummer
block housings are available, making the use of
tailored housings unnecessary and thus
enabling cost-effective bearing arrangements
to be made.
For many years SKF has been one of the
leading suppliers of split plummer block housings synonymous with operational reliability
and quality.
SNL plummer block housings in the 30 and

31 series are also referred to as Large SNL
plummer block housings.
These plummer block housings enable the
bearings to achieve maximum bearing service
life with less need for maintenance. This
supports user efforts to further reduce maintenance costs. Among other enhancements, SNL
housings are designed for easy alignment and
handling during installation.
Another benefit is the choice of oil or grease
lubrication for the bearings housed in SNL
plummer blocks. A range of seals for oil
lubrication and difficult environments provide
trouble-free operation.
488
Introduction
One basic design many variants

Large SNL plummer block housings are
intended for spherical roller bearings and CARB
toroidal bearings. The housings are designed
on a building block principle.This enables
more possibilities when it comes to selecting
the bearing designs, shaft, seals and the type of
lubricant and/or lubrication delivery system.
A building block system

The basis of the original SNL plummer block
housing system consists of a number of housings with the same basic design but in different
sizes. By combining the housings with the different standard seals, a wide variety of variants,
all belonging to the standard range, can be
supplied to cover most applications.
SNL 30 and 31 series housings are available
for shaft diameters ranging from 150 to 530 mm,
inclusive.
The standard range also covers housings with
drilled and tapped holes for lubrication fittings.
Upon request, housings can be drilled for condition monitoring.
SNL 30 and 31 series plummer block housings

are made of grey cast iron and demonstrate the
same high strength as the earlier SD housings.
Should, however, this strength be inadequate,
dimensionally equivalent SNLD plummer block
housings made of spheroidal graphite cast iron
are available.
The large SNL and SNLD plummer block
housings in the 31 series are dimensionally
interchangeable with the earlier SD and SDD
housings. However, for SNL and SNLD plummer
block housings in the 30 series, one needs to
check the bearing axial position, as the bearing
center is off-set compared to the housing base
center (dimension s in the tables). The housing
boundary dimensions conform to ISO 113:1999.
Several sealing options

An important advantage of the SNL plummer
block housings is that they can be fitted with a
choice of seals. The standard seals supplied by
SKF for the large SNL 30 and 31 series housings include labyrinth seals and heavy-duty
taconite seals as well as end covers. Oil seals
are also available and are supplied together with
the housing, as the housing has to be modified
to accomodate the seal.
489

Seals
Standard seals
The standard seals available from SKF for large
SNL housings (series SNL 30 and SNL 31) are
one-piece labyrinth seals and the heavy-duty
taconite seals. The seals are easy to install and
are supplied separately.
The standard seals as well as the seals for use
with oil lubrication are presented in Table 1, which
gives a comprehensive overview of the seal types,
their design features and their suitability for various operating conditions. Detailed information on
the various standard and special seals including
properties and availability will be found on pages
491 to 492.
TSD .. U1)
TNF ..
TSN ..
Table 1
Seal selection
TSN..
TNF..
TSD..U1)
Temperature, F
C
-58 to +392 F
(-50 to +200 C)
-40 to +212 F
(-40 to +100 C)
-58 to +392 F
(-50 to +200 C)
Peripheral speed
++
39 ft/sec (12 m/sec)
++
Misalignment, minutes
18
18
18
Grease relubrication
Oil lubrication
++
Low friction
++
++
Axial shaft displacement
Vertical arrangement
--
--
Dust
++
Fine particulate contaminants
++
Coarse particulate contaminants
++
Abrasive contaminants
++
++
++
Liquids when sprayed
--
++
Direct sunlight
++
++
++
Properties
Sealing ability against
Symbols:
1)
490
++
very suitable
suitable
limited suitability
-- unsuitable
The oil seals are supplied together with housings prepared for oil lubrication. Oil seals can be ordered separately as spares only.
Seals
Labyrinth seals
Taconite heavy-duty seals
The labyrinth rings (Figure 1) are made of castiron and have three radially arranged labyrinth
steps which form a narrow sealing gap with the
housing grooves.
Hollow O-ring cords of silicone rubber
(supplied with the seals) ensure that the
labyrinth rings, which are mounted with a loose
fit, rotate with the shaft. Angular misalignments
of the shaft up to approximately 18 minutes are
permissible. The operating temperature range
for the labyrinth seals is -58 to +392 F
(50 to +200 C).
When labyrinth seals are used, axial
movement of the shaft relative to the housing is
not limited.
The labyrinth seals are supplied individually.
For bearing arrangements for through shafts, it is
therefore necessary to order two rings. The
labyrinth seal is identified by the prefix TS
followed by the size identification, e.g. TS 34.
Taconite is a very fine-grained mineral, which

is extremely difficult to seal out. For bearing
arrangements, which must operate under very
arduous conditions (such as those encountered
in mining), labyrinth seals, which can be relubricated, are recommended as grease
enhances the sealing effect and extends the
serviceability of the seals. SKF has developed a
heavy-duty seal (which can seal out taconite,
hence the name), which can be supplied for use
with SNL housings.
The taconite seal design (Figure 2) is based
on a labyrinth seal with the labyrinth stages
arranged axially and fits the standard housings.
A V-ring seal mounted on the shaft seals
against the non-rotating part of the seal, which
is inserted in the seal groove, prevents contaminants from penetrating to the bearing
when the seal is relubricated. This grease is
supplied via a grease nipple on the non-rotating part of the seal. Angular misalignments of
the shaft of up to approximately 18 minutes
are possible.
The permissible operating temperature range
for the seal is between -40 to +212 F
(40 and +100 C). Please contact SKF for
applications above 212 F (100 C). The rubber
O-ring and V-ring limit the operating temperature to 212 F (100 C). However, SKF can
supply high temperature O-rings and V-rings
made of fluoro rubber for operation at higher
temperatures.
Figure 1
Labyrinth seal

the housing is limited for this type of taconite
seal to approximately 2 mm for sizes from
150 up to 200 mm and 4 mm for larger
shaft diameters.
These seals are supplied individually so that
for housings used on through shafts, it is necessary to order two seals. The seal is identified
by the prefix TNF followed by the size identification, e.g. TNF 34.
Seals for oil lubrication

Special seals (oil seals) are required to
prevent oil from escaping from the housing
when oil lubrication is applied. For SNL housings, SKF has developed the non-rubbing seal
of the U-design (Figure 3). These U-seals
require modified housings and comprise two
parts: one which is stationary and fitted in the
modified seal groove, and the other which is
mounted on the shaft and rotates. The hollow
O-ring cords of silicone rubber inserted
between the labyrinth ring and the shaft
allows the ring, which is mounted with a loose
fit, to rotate with the shaft, and oil cannot
escape along the shaft. These oil seals do not
limit axial movement of the shaft relative to
the housing.
The modified SNL housing is supplied
together with the seals as a unit. The housings
with seals are identified by the suffix TURT
(TURA for CARB bearings) e.g. SNL 3134 TURT.
The seal itself is designated TSD .. U.
Figure 2
Figure 3
Oil seal
491

Seals
Special seals
In applications where, for some reason the
standard seals cannot be used, special seals
must be fitted. The SNL housings can be supplied without seals for such applications and
are relatively easy to equip with special seals. It
is recommended that housings of series SNL ..
G are used rather than those of series SNL as
they have a comparatively larger bore at the
shaft entrance. There is therefore more room
to accommodate a seal, so that there are
more choices for seal design.
Special seals are not normally supplied by

SKF. Therefore, the relevant housing dimensions are given in Tables 2 and 3.
A5
A6
Db Dc Dd
A4
A3
Table 2
Housing
Dimensions
Size
A3
mm
SNL 3036
SNL 3038
SNL 3040
A4
A5
A6
Db
Dc
Dd
158
168
186
11
11
11
5.5
5.5
5.5
22
22
22
181.2
191.4
201.4
196.4
206.4
216.4
205.2
215.4
225.4
SNL 3044
SNL 3048
SNL 3052
206
214
231
11
11
11
5.5
5.5
5.5
22
22
22
221.4
241.4
261.6
236.4
256.4
276.6
245.4
265.4
285.6
SNL 3056
SNL 3060
SNL 3064
249
249
279
11
11
11
5.5
5.5
5.5
22
22
22
281.6
301.6
321.8
296.6
316.6
336.8
305.6
325.6
345.8
SNL 3068
SNL 3072
SNL 3076
299
297
328
11
11
11
5.5
5.5
5.5
22
22
22
342.4
362.4
382.4
357.4
377.4
397.4
366.4
386.4
406.4
SNL 3080
SNL 3084
SNL 3088
328
328
358
11
11
11
5.5
5.5
5.5
22
22
22
402.8
422.8
442.8
417.8
437.8
457.8
426.8
446.8
466.8
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
388
388
388
398
11
11
11
11
5.5
5.5
5.5
5.5
22
22
22
22
463
483
503
533
478
498
518
548
487
507
527
557
SNL 3134
SNL 3136
SNL 3138
159
169
187
11
11
11
5.5
5.5
5.5
22
22
22
171.2
181.2
191.4
186.4
196.4
206.4
195.2
205.2
215.4
SNL 3140
SNL 3144
SNL 3148
207
215
231
11
11
11
5.5
5.5
5.5
22
22
22
201.4
221.4
241.4
216.4
236.4
256.4
225.4
245.4
265.4
SNL 3152
SNL 3156
SNL 3160
249
249
280
11
11
11
5.5
5.5
5.5
22
22
22
261.6
281.6
301.6
276.6
296.6
316.8
285.6
305.6
325.6
SNL 3164
SNL 3168
SNL 3172
300
328
328
11
11
11
5.5
5.5
5.5
22
22
22
321.8
342.4
362.4
336.8
357.4
377.4
345.8
366.4
386.4
SNL 3176
SNL 3180
SNL 3184
328
358
388
11
11
11
5.5
5.5
5.5
22
22
22
382.4
402.8
422.8
397.4
417.8
437.8
406.4
426.8
446.8
SNL 3188
SNL 3192
SNL 3196
388
398
398
11
11
11
5.5
5.5
5.5
22
22
22
442.8
463
483
457.8
478
498
466.8
487
507
492
Seals
A5
A6
Db Dc Dd
A4
A3
Table 3
Housing
Dimensions
Size
A3
mm
SNL 3036 G
SNL 3038 G
SNL 3040 G
A4
A5
A6
Db
Dc
Dd
156
166
184
11
11
11
5.5
5.5
5.5
22
22
22
221.4
221.4
241.4
236.4
236.4
256.4
245.4
245.4
265.4
SNL 3044 G
SNL 3048 G
SNL 3052 G
203
211
228
11
11
11
5.5
5.5
5.5
22
22
22
261.6
281.6
301.6
276.6
296.6
316.8
285.6
305.6
325.6
SNL 3056 G
SNL 3060 G
SNL 3064 G
247
247
277
11
11
11
5.5
5.5
5.5
22
22
22
321.8
341.8
361.8
336.8
356.8
376.8
345.8
365.8
385.8
SNL 3068 G
SNL 3072 G
SNL 3076 G
295
293
325
11
11
11
5.5
5.5
5.5
22
22
22
381.8
401.8
422.8
396.8
416.8
437.8
405.8
425.8
446.8
SNL 3080 G
SNL 3084 G
SNL 3088 G
325
325
354
11
11
11
5.5
5.5
5.5
22
22
22
463
483
503
478
498
518
487
507
527
SNL 3092 G
SNL 3096 G
SNL 30/500 G
SNL 30/530 G
384
384
384
392
11
11
11
11
5.5
5.5
5.5
5.5
22
22
22
22
533
533
563
603
548
548
578
618
557
557
587
627
SNL 3134 G
SNL 3136 G
SNL 3138 G
157
166
185
11
11
11
5.5
5.5
5.5
22
22
22
201.4
221.4
221.4
216.4
236.4
236.4
225.4
245.4
245.4
SNL 3140 G
SNL 3144 G
SNL 3148 G
204
213
230
11
11
11
5.5
5.5
5.5
22
22
22
241.4
261.6
281.6
256.4
276.6
296.6
265.4
285.6
305.6
SNL 3152 G
SNL 3156 G
SNL 3160 G
248
248
278
11
11
11
5.5
5.5
5.5
22
22
22
301.6
321.8
341.8
316.8
336.8
356.8
325.6
345.8
365.8
SNL 3164 G
SNL 3168 G
SNL 3172 G
297
325
325
11
11
11
5.5
5.5
5.5
22
22
22
361.8
382.4
402.8
376.8
397.4
417.8
385.8
406.4
426.8
SNL 3176 G
SNL 3180 G
SNL 3184 G
325
354
384
11
11
11
5.5
5.5
5.5
22
22
22
422.8
463
483
437.8
478
498
446.8
487
507
SNL 3188 G
SNL 3192 G
SNL 3196 G
384
395
394
11
11
11
5.5
5.5
5.5
22
22
22
503
533
563
518
548
578
527
557
587
493

End covers
Table 4
Permissible length of shaft end
Housing
Bearing
Size
bb
ba
bc
ba
max1)
bb
bc
mm
SNL 3036
23036
24036
23038
24038
23040
24040
23044
24044
23048
24048
23052
24052
23056
24056
23060
24060
23064
24064
23068
24068
23072
24072
23076
24076
23080
24080
23084
24084
23088
24088
23092
24092
23096
24096
230/500
240/500
230/530
240/530
72
85
73
86
78
91
91
105
97
110
103
121
108
125
118
139
121
140
130
153
130
153
134.5
157
145
171
146
171
160.5
188
163.5
191
164.5
191
173.5
199
187.5
220
102
102
108
108
112
112
122
122
128
128
136
136
146
146
149
149
170
170
181
181
181
181
197
197
203
203
203
203
218
218
238
238
238
238
238
238
243
243
66.5
79.5
68
80.5
72.5
86
86
100
92
105
98
116
103
120
113
134
115.5
135
124.5
148
125
148
129.5
152
140
166
141
166
155.5
183
158.5
186
159.5
186
168.5
194
182.5
215
107.5
107.5
113.5
113.5
117.5
117.5
127.5
127.5
133.5
133.5
141.5
141.5
151.5
151.5
154.5
154.5
175.5
175.5
186.5
186.5
186.5
186.5
202.5
202.5
208.5
208.5
208.5
208.5
223.5
223.5
243.5
243.5
243.5
243.5
243.5
243.5
248.5
248.5
23134
23136
23138
23140
23144
23148
23152
23156
23160
23164
23168
23172
23176
23180
23184
23188
23192
23196
78
83
88
93
100
106
116
119
138
149
172
176
179
187
207
208
220
224
102
108
112
122
128
136
146
149
170
181
197
203
203
218
238
238
243
243
73
78
83
88
95
101
111
114
133
144
167
171
174
182
202
203
215
219
107.5
113.5
117.5
127.5
133.5
141.5
151.5
154.5
175.5
186.5
202.5
208.5
208.5
223.5
243.5
243.5
248.5
248.5
SNL 3038
SNL 3040
SNL 3048
SNL 3052
SNL 3056
SNL 3060
SNL 3064
SNL 3068
SNL 3072
SNL 3076
SNL 3080
SNL 3084
SNL 3088
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
SNL 3134
SNL 3136
SNL 3138
SNL 3140
SNL 3144
SNL 3148
SNL 3152
SNL 3156
SNL 3160
SNL 3164
SNL 3168
SNL 3172
SNL 3176
SNL 3180
SNL 3184
SNL 3188
SNL 3192
SNL 3196
1)
494
ba
min
SNL 3044
bb
ba
bc
Dimensions
For non-locating arrangements, which are not mounted centrally in the bearing seating, the value of
ba max must be correspondingly reduced
End covers
End covers
Locating rings
For housings mounted at the ends of shafts,

the one opening should be fitted with an end
cover, which fits into the seal groove
(Figure 4). Details of the permissible length of
the shaft end can be found in Table 4. The
end covers are of cast-iron and are inserted
with a hollow O-ring cord of silicone rubber in
the seal groove in the housing. The end covers
are suitable for operating temperatures in the
range -58 to + 392 F (50 to +200 C).
The standard end cover is designated by
the prefix ETS followed by the housing size
identification, e.g. ETS 34. End covers for oil
lubricated SNL housings are identified by
suffix R, e.g. ETS 34 R.
The bearing seating in the housing is

sufficiently wide to enable the bearing to be
displaced axially. The locating or held bearing
must always be fixed axially in position in the
housing bore by locating rings at both sides
(Figure 5).
CARB bearings are non-locating bearings
and cannot take axial loads. Since axial displacement is accommodated within a CARB
bearing (together with any misalignment), it is
necessary to locate the outer ring axially in its
seating by inserting locating rings at each side
of the bearing.
The locating rings are identified by the prefix
FRB followed by figures giving the width/outside diameter in millimeters, e.g. FRB 10/280.
Figure 4
Figure 5
Housing with end cover
Housing with locating rings

at both sides of bearing
495

Lubrication
Lubrication
Grease lubrication
SNL plummer block housings are designed so

that the bearings can be lubricated with
grease or oil, although grease lubrication is
generally preferred. The lubricant should be
selected with reference to the operating
conditions.
Table 5
Grease quantities
Housing
Size
Grease quantity
First fill1)
kg
SNL 3036
SNL 3038
SNL 3040
1.2
1.5
2.0
SNL 3044
SNL 3048
SNL 3052
2.7
3.0
3.9
SNL 3056
SNL 3060
SNL 3064
4.9
5.2
7.0
SNL 3068
SNL 3072
SNL 3076
8.7
10.9
10.9
SNL 3080
SNL 3084
SNL 3088
11.7
11.8
14.4
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
18.8
18.5
20.0
21.5
SNL 3134
SNL 3136
SNL 3138
1.1
1.4
1.8
SNL 3140
SNL 3144
SNL 3148
2.3
2.7
3.4
SNL 3152
SNL 3156
SNL 3160
4.3
4.4
6.2
SNL 3164
SNL 3168
SNL 3172
7.7
9.4
9.7
SNL 3176
SNL 3180
SNL 3184
9.6
12.2
14.9
SNL 3188
SNL 3192
SNL 3196
16.2
17.4
17.2
1) Fills approximately 40 % of the

free space in the housing
496
In the majority of applications, the amount of

grease applied to the SNL housings when
mounting (initial fill) or after an inspection is
adequate until the next planned inspection.
Certain operating conditions, e.g. high speeds,
high temperatures or heavy loads, may mean
that more frequent relubrication is necessary.
Table 5 gives guideline values for the grease
quantities to be applied for the first fill.
Markings in each corner inside the base give an
indication of the grease level for the initial fill
(Figure 6).
There are three drilled and tapped holes for a
grease nipple AH 1/8-27 PTF in the housing:
two in the cap and one in the base. These holes
are closed by metallic plugs. The two markings
at the outer sides of the central ridge indicate
the position for lubrication holes for the seals.
Figure 6
Grease level markings

for first fill
Figure 7

via the outer ring
Lubrication
A grease nipple AH 1/8-27 PTF is supplied

with the housing. The grease nipple kit also
contains a plastic grease nipple protector, a
grease nipple M1 G 1/8 and an adapter LAPN
1/8. This adapter transforms the standard
drilled 1/8-27 NPSF thread to a G 1/4 which
enables the use of grease lubricators such as
SKF SYSTEM 24.
It is recommended that spherical roller bearings having a lubrication groove and three
holes in the outer ring (designation suffix W33)
be lubricated via this feature (Figure 7). In this
case the relubrication hole in the base or in the
center of the cap should be used.
It should be noted that when spherical roller
bearings are to be relubricated via the outer
ring, they should be rotated. If outer ring relubrication is not possible or if CARB bearings
are used, the standard grease nipple supplied
with the housing should be inserted in the hole
on the side of the cap and used for this purpose (Figure 8). If it is desired to use a grease
nipple other than that supplied with the housing, adapters are available which make a
reworking of the available drilled and tapped
hole unnecessary.
Where the bearings are mounted on adapter

sleeves, the grease should be introduced at
the side opposite to the lock nut of the sleeve.
If frequent relubrication is required, it is
advisable to provide the housing with grease
escape holes (Figure 9) through which excess
grease can escape. Recommended dimensions
will be found in Table 6. SNL housings with
grease escape holes in the base can be supplied. This housing design is identified by the
suffix V, e.g. SNL 3134 V.
SNL housings can also be equipped with
grease lubricators. Recommended are the
SKF SYSTEM 24 lubricators (e.g. LAGD
125/WA2), which provide a reliable alternative
to manual relubrication.
Figure 8

from the side
Figure 9
Housing with grease

escape hole
Table 6
Recommended dimensions for grease
escape holes
Housing
Size
Dimensions
J7
Ja
mm
SNL 3036
SNL 3038
SNL 3040
105
110
120
34
38
36
30
30
30
SNL 3044
SNL 3048
SNL 3052
120
130
145
36
42
43
30
40
40
SNL 3056
SNL 3060
SNL 3064
150
165
180
44
51
53
40
40
40
SNL 3068
SNL 3072
SNL 3076
180
180
185
53
53
51
40
40
40
SNL 3080
SNL 3084
SNL 3088
220
220
230
51
53
58
40
40
40
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
260
260
260
280
58
58
58
58
40
40
40
40
SNL 3134
SNL 3136
SNL 3138
105
110
120
34
38
36
30
30
30
SNL 3140
SNL 3144
SNL 3148
120
130
145
36
42
43
30
40
40
SNL 3152
SNL 3156
SNL 3160
150
165
180
44
51
53
40
40
40
SNL 3164
SNL 3168
SNL 3172
180
185
220
53
51
51
40
40
40
SNL 3176
SNL 3180
SNL 3184
220
230
260
53
58
58
40
40
40
SNL 3188
SNL 3192
SNL 3196
260
280
280
58
58
58
40
40
40
N3
The dimensions are those recommended when the

standard grease nipple AH 1/8-27 PTF is used
(supplied with the housing) but can also be applied if
nipples having threads R 1/8, KR 1/8, M 10x1 or G 1/4
(with adapter LAPN 1/8) are used. The recommendations also
apply if grease dispensers, e.g. SKF SYSTEM 24, are used.
497

Lubrication
Oil lubrication
Figure 10
The new SNL 30 and SNL 31 housings can be

used for oil lubrication at relatively high speeds.
When using oil, however, the specially developed
U-design seals should be incorporated to avoid
oil loss from the housing (Figure 10). These
seals are described on page 491. In order for
these seals to be used, the housing must be
modified so that SNL housings for oil lubrication
are only supplied, complete with seals.
Oil lubricated SNL housings can also be
equipped with oil levellers, LAHD series, which
are designed for automatic adjustment of the
optimal oil lubrication level within the bearing
housing.
Housing for oil lubrication
498
Mounting
Mounting
SNL housings together with SKF bearings are
robust and operationally reliable bearing
arrangements which have long lives. However,
if they are to achieve their full potential and
not fail prematurely, they must be properly
mounted. Incorrect procedures or unsuitable tools can influence life negatively.
When mounting the housings it should be
remembered that the housings are asymmetrical internally and therefore the bearings
are not always mounted in the center of
the housing.
Vertical markings on the housing base end
faces indicate the location of the center of the
bearing seating.
Mounting the bearing

The bearings can be mounted either on a
tapered seating normally for SNL housings
in the form of an adapter sleeve or on a
cylindrical seating. When a bearing is correctly
mounted on a sleeve there will be interference
fits between the inner ring, sleeve and shaft.
The degree of interference is determined by
how far the bearing is driven up on the sleeve
and either the internal clearance reduction or
the axial drive-up distance can be used as a
measure. The clearance reduction in spherical
roller bearings can be measured using a feeler
gauge, or the SKF drive-up method can be
used.
For CARB bearings either the clearance
reduction or the axial drive-up distance should
be measured. When using a feeler gauge to
measure clearance reduction, it is important
that the inner and outer rings of the bearing
are not displaced with respect to each other.
The SKF drive-up method can also be applied.
Adapter sleeves with the designation
OH .. H in the product tables indicate that the
sleeves are provided with the necessary ducts
to enable the bearings to be mounted using
the oil injection method. Oil is supplied to the
nut side of the sleeve.
Bearings with cylindrical bore are normally
mounted with an interference fit on the
shaft. Appropriate shaft tolerances should be
selected. The recommendations applying to
spherical roller bearings also apply to CARB
bearings.
J6
N4
Table 7
Position and size of dowel pin holes
Housing
Dimensions
Size
J6
N4
Housing
Dimensions
Size
J6
max
mm
SNL 3036
SNL 3038
SNL 3040
470
490
520
SNL 3044
SNL 3048
SNL 3052
N4
max
mm
20
20
20
SNL 3134
SNL 3136
SNL 3138
470
490
520
20
20
20
560
590
650
20
20
20
SNL 3140
SNL 3144
SNL 3148
560
590
650
20
20
20
SNL 3056
SNL 3060
SNL 3064
720
740
770
20
20
25
SNL 3152
SNL 3156
SNL 3160
720
740
770
20
20
25
SNL 3068
SNL 3072
SNL 3076
820
820
880
25
25
SNL 3164
SNL 3168
SNL 3172
820
880
920
25
25
30
SNL 3080
SNL 3084
SNL 3088
920
960
1 020
SNL 3176
SNL 3180
SNL 3184
960
1 020
1 070
30
35
35
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
1 070
1 070
1 120
1 210
SNL 3188
SNL 3192
SNL 3196
1 120
1 160
1 210
35
40
40
Support surface for housing base
Attachment bolts
To guarantee long bearing service life, it is

recommended that the support surface for the
housing is finished to Ra 492 in (12.5 m).
The flatness tolerance should be to IT7. For
moderate demands IT8 may be satisfactory.
It is recommended that hexagon-headed bolts

to strength class 8.8 according to the European
Standard EN 24014 be used. If the load does
not act vertically to the base, it may be necessary to use stronger, class 10.9 bolts. Details of
the appropriate tightening torques for the bolts
to class 8.8 are given in Table 9 on page 501.
Dowel pins
SNL housings are designed for loads acting
vertically to the housing base support. If they
are to be subjected to moderate or heavy
loads acting parallel to the base support, a
stop should be provided, or the housing
should be pinned to its support.
Recommendations for the position and size of
holes to take dowel pins are given in Table 7.
499

SNL plummer block housings are intended for

loads acting vertically towards the base plate
(support). If loads acting in other directions
occur, checks should be made to ensure that
the magnitude of the load is permissible for
the housing, the bolts joining the housing cap
and base, and for the attachment bolts.
P55
P90
P120
P150
P180
Pa
Load carrying ability of the housing

Guideline values for the breaking load P of the
housing for various load directions are given in
Table 8. Using these values and a safety
factor selected with respect to the operating
conditions, the permissible load for the housing can be calculated. In general engineering a
safety factor of 6 is often used.
For special purposes where extra strength
and resistance to shock loads are required,
SKF supplies as standard a range of
spheroidal graphite cast-iron housings.
Spheroidal graphite cast-iron housings are
designated SNLD followed by the size identification, e.g. SNLD 3134. For housings made of
spheroidal graphite cast-iron, the values of P
in Table 8 should be multiplied by 1.8.
It is important for the load carrying ability of
the housing that the bolts joining cap and base
are properly tightened in accordance with the
values given in Table 9. The axial load carrying
capacity of the housing is approximately 65%
of P180. For load angles between 55 and
120 as well as for axial loads, if the load acting parallel to the base plate (support surface)
exceeds 5% of P180, the housing should be
pinned to the support or a stop should be
provided in the direction of the load.
Load carrying ability of bolts
SNL plummer block housings are supplied
with cap bolts (to join cap and base) to
strength class 8.8 as standard. The guideline
values for the yield point Q for the cap bolts
are given in Table 9 for various load directions
as well as the corresponding maximum radial
loads F.
Table 8
Breaking loads for SNL plummer block housing
Housing
Breaking loads for SNL housing
Size
P55
kN
SNL 3036
SNL 3038
SNL 3040
P90
P120
P150
P180
Pa
2100
2400
2700
1000
1150
1300
760
850
1000
680
760
880
850
950
1100
550
620
710
SNL 3044
SNL 3048
SNL 3052
3200
4000
4200
1600
1900
2000
1100
1400
1500
1000
1300
1400
1300
1600
1700
840
1000
1100
SNL 3056
SNL 3060
SNL 3064
4700
5000
6000
2300
2400
2900
1700
1800
2200
1500
1600
1900
1900
2000
2400
1200
1300
1500
SNL 3068
SNL 3072
SNL 3076
7000
7000
7 500
3400
3400
3 600
2500
2500
2 600
2200
2200
2 300
2800
2800
3 000
1800
1800
1 900
SNL 3080
SNL 3084
SNL 3088
7 700
8 000
8 700
3 600
3 900
4 200
2 700
2 900
3 100
2 400
2 500
2 700
3 000
3 200
3 500
2 000
2 100
2 200
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
9 600
9 600
10 000
11 200
4 600
4 600
4 800
5 400
3 400
3 400
3 600
4 000
3 000
3 000
3 100
3 500
3 800
3 800
4 000
4 400
2 400
2 400
2 500
2 800
SNL 3134
SNL 3136
SNL 3138
2100
2400
2700
1000
1150
1300
760
850
1000
680
760
880
850
950
1100
550
620
710
SNL 3140
SNL 3144
SNL 3148
3200
4000
4200
1600
1900
2000
1100
1400
1500
1000
1300
1400
1300
1600
1700
840
1000
1100
SNL 3152
SNL 3156
SNL 3160
4700
5000
6000
2300
2400
2900
1700
1800
2200
1500
1600
1900
1900
2000
2400
1200
1300
1500
SNL 3164
SNL 3168
SNL 3172
7000
7 500
7 700
3400
3 600
3 600
2500
2 600
2 700
2200
2 300
2 400
2800
3 000
3 000
1800
1 900
2 000
SNL 3176
SNL 3180
SNL 3184
8 000
8 700
9 600
3 900
4 200
4 600
2 900
3 100
3 400
2 500
2 700
3 000
3 200
3 500
3 800
2 100
2 200
2 400
SNL 3188
SNL 3192
SNL 3196
10 000
10 700
11 200
4 800
5 200
5 400
3 600
3 800
4 000
3 100
3 300
3 500
4 000
4 200
4 400
2 500
2 700
2 800
500
Q120
F120
Q150
F150
Q180
F180
Table 9
Load carrying ability and tightening torque for cap bolts and attachment bolts
Housing
Size
Cap bolts
Yield point
for four bolts
Q150
Q120
Tightening
torque
Designation
to EN 24014
Attachment bolts
Size
Tightening
torque
kN
Nm
Nm
SNL 3036
SNL 3038
SNL 3040
1800
1800
1800
1040
1040
1040
900
900
900
760
760
760
440
440
440
380
380
380
350
350
350
M 24x140
M 24x140
M 24x150
M 24
M 24
M 24
665
665
665
SNL 3044
SNL 3048
SNL 3052
1800
1800
2860
1040
1040
1650
900
900
1 430
760
760
1 240
440
440
720
380
380
620
350
350
400
M 24x160
M 24x160
M 30x180
M 30
M 30
M 30
1 310
1 310
1 310
SNL 3056
SNL 3060
SNL 3064
2860
2860
2860
1650
1650
1650
1 430
1 430
1 430
1 240
1 240
1 240
720
720
720
620
620
620
400
400
400
M 30x200
M 30x200
M 30x220
M 36
M 36
M 36
2 280
2 280
2 280
SNL 3068
SNL 3072
SNL 3076
2860
2860
4 200
1650
1650
2 400
1 430
1 430
2 100
1 240
1 240
1 600
720
720
920
620
620
800
400
400
600
M 30x220
M 30x220
M 36x240
M 36
M 36
M 36
2 280
2 280
2 280
SNL 3080
SNL 3084
SNL 3088
4 200
4 200
4 200
2 400
2 400
2 400
2 100
2 100
2 100
1 600
1 600
1 600
920
920
920
800
800
800
600
600
600
M 36x240
M 36x240
M 36x240
M 36
M 36
M 42
2 280
2 280
3 640
SNL 3092
SNL 3096
SNL 30/500
SNL 30/530
5 800
5 800
5 800
5 800
3 350
3 350
3 350
3 350
2 900
2 900
2 900
2 900
2 200
2 200
2 200
2 200
1 260
1 260
1 260
1 260
1 100
1 100
1 100
1 100
850
850
850
850
M 42x280
M 42x280
M 42x280
M 42x280
M 42
M 42
M 42
M 48
3 640
3 640
3 640
5 450
SNL 3134
SNL 3136
SNL 3138
1 800
1 800
1 800
1 040
1 040
1 040
900
900
900
760
760
760
440
440
440
380
380
380
350
350
350
M 24x140
M 24x140
M 24x150
M 24
M 24
M 24
665
665
665
SNL 3140
SNL 3144
SNL 3148
1 800
1 800
2 860
1 040
1 040
1 650
900
900
1430
760
760
1240
440
440
720
380
380
620
350
350
400
M 24x160
M 24x160
M 30x180
M 30
M 30
M 30
1 310
1 310
1 310
SNL 3152
SNL 3156
SNL 3160
2 860
2 860
2 860
1 650
1 650
1 650
1430
1430
1430
1240
1240
1240
720
720
720
620
620
620
400
400
400
M 30x200
M 30x200
M 30x220
M 36
M 36
M 36
2 280
2 280
2 280
SNL 3164
SNL 3168
SNL 3172
2 860
4 200
4 200
1 650
2 400
2 400
1430
2 100
2 100
1240
1 600
1 600
720
920
920
620
800
800
400
600
600
M 30x220
M 36x240
M 36x240
M 36
M 36
M 36
2 280
2 280
2 280
SNL 3176
SNL 3180
SNL 3184
4 200
4 200
5 800
2 400
2 400
3 350
2 100
2 100
2 900
1 600
1 600
2 200
920
920
1 260
800
800
1 100
600
600
850
M 36x240
M 36x240
M 42x280
M 36
M 42
M 42
2 280
3 640
3 640
SNL 3188
SNL 3192
SNL 3196
5 800
5 800
5 800
3 350
3 350
3 350
2 900
2 900
2 900
2 200
2 200
2 200
1 260
1 260
1 260
1 100
1 100
1 100
850
850
850
M 42x280
M 42x300
M 42x300
M 42
M 42
M 48
3 640
3 640
5 450
Q180
Maximum load
for four bolts
F120
F150
F180
kN
501

Large SNL plummer block housings
for bearings on adapter sleeves
da 150 200 mm
Ca
Da da
H
s
H1
A3
A1
A
A2
Shaft
Housing
dimensions
H2
J1
N1 s
mm
150
230 180 333 170 70
430 100 510 34 28 14 24
69.5
SNL 3134
SNL 3134
SNL 3134 TURT
SNL 3134 TURA
TS 34
TNF 34
TSD 3134 U
TSD 3134 U
ETS 34
ETS 34
ETS 3134 R
ETS 3134 R
160
230 180 333 170 70
430 100 510 34 28 14 24
69.5
SNL 3036
SNL 3036
SNL 3036 TURT
SNL 3036 TURA
TS 36
TNF 36
TSD 3036 U
TSD 3036 U
ETS 36
ETS 36
ETS 3036 R
ETS 3036 R
240 190 353 180 75
450 110 530 34 28 15 24
77.5
SNL 3136
SNL 3136
SNL 3136 TURT
SNL 3136 TURA
TS 36
TNF 36
TSD 3136 U
TSD 3136 U
ETS 36
ETS 36
ETS 3136 R
ETS 3136 R
240 190 353 180 75
450 110 530 34 28 15 24
77.5
SNL 3038
SNL 3038
SNL 3038 TURT
SNL 3038 TURA
TS 38
TNF 38
TSD 3038 U
TSD 3038 U
ETS 38
ETS 38
ETS 3038 R
ETS 3038 R
260 210 375 190 80
480 120 560 34 28 10 24
97.5
SNL 3138
SNL 3138
SNL 3138 TURT
SNL 3138 TURA
TS 38
TNF 38
TSD 3138 U
TSD 3138 U
ETS 38
ETS 38
ETS 3138 R
ETS 3138 R
260 210 375 190 80
480 120 560 34 28 10 24
97.5
SNL 3040
SNL 3040
SNL 3040 TURT
SNL 3040 TURA
TS 40
TNF 40
TSD 3040 U
TSD 3040 U
ETS 40
ETS 40
ETS 3040 R
ETS 3040 R
280 230 411 210 85
510 130 610 42 35 10 30
123
SNL 3140
SNL 3140
SNL 3140 TURT
SNL 3140 TURA
TS 40
TNF 40
TSD 3140 U
TSD 3140 U
ETS 40
ETS 40
ETS 3140 R
ETS 3140 R
280 230 411 210 85
510 130 610 42 35 10 30
123
SNL 3044
SNL 3044
SNL 3044 TURT
SNL 3044 TURA
TS 44
TNF 44
TSD 3044 U
TSD 3044 U
ETS 44
ETS 44
ETS 3044 R
ETS 3044 R
290 240 434 220 90
540 140 640 42 35 12 30
138
SNL 3144
SNL 3144
SNL 3144 TURT
SNL 3144 TURA
TS 44
TNF 44
TSD 3144 U
TSD 3144 U
ETS 44
ETS 44
ETS 3144 R
ETS 3144 R
kg
502
End cover
mm
200
H1
Seal
180
Designations
Components
Housing only
da
170
A1
Mass
A4

da 150 200 mm
N
N1
G
J1
H2
J
L
Shaft
Bearing
seating
Width across seals
da
Ca
A2
mm
mm
150
108
280
240
302
160
108
280
240
116
300
115
170
180
200
Eye bolts
According to
DIN 580

Adapter sleeve
Locating rings
CARB bearing
225
M 16
23134 CCK/W33
C 3134 K1
H 3134
H 3134 L
2 FRB 10/280
2 FRB 10/280
304
225
M 16
23036 CCK/W33
C 3036 K
H 3036
H 3036
2 FRB 17/280
2 FRB 17/280
250
317
235
M 16
23136 CCK/W33
C 3136 K
H 3136
H 3136 L
2 FRB 10/300
2 FRB 10/300
290
250
318
235
M 16
23038 CCK/W33
C 3038 K
H 3038
H 3038
4 FRB 10/290
4 FRB 10/290
124
320
270
334
255
M 20
23138 CCK/W33
C 31381
H 3138
H 3138 L
2 FRB 10/320
2 FRB 10/320
122
310
270
331
255
M 20
23040 CCK/W33
C 3040 K
H 3040
H 3040
4 FRB 10/310
4 FRB 10/310
132
340
290
351
275
M 20
23140 CCK/W33
C 3140 K
H 3140
H 3140
2 FRB 10/340
2 FRB 10/340
130
340
290
353
275
M 20
23044 CCK/W33
C 3044 K
OH 3044 H
OH 3044 H
4 FRB 10/340
4 FRB 10/340
140
370
300
361
285
M 20
23144 CCK/W33
C 3144 K
OH 3144 H
OH 3144 HTL
2 FRB 10/370
2 FRB 10/370
Da
A3
A4
mm
Please check availability of the bearing before incorporating it in a bearing arrangement design.
503

da 220 300 mm
Ca
Da da
H
s
H1
A3
A1
A
A2
Shaft
Housing
dimensions
mm
220
290 240 434 220 90
540 140 640 42 35 12 30
138
SNL 3048
SNL 3048
SNL 3048 TURT
SNL 3048 TURA
TS 48
TNF 48
TSD 3048 U
TSD 3048 U
ETS 48
ETS 48
ETS 3048 R
ETS 3048 R
310 260 474 240 95
600 150 700 42 35 12 30
187
SNL 3148
SNL 3148
SNL 3148 TURT
SNL 3148 TURA
TS 48
TNF 48
TSD 3148 U
TSD 3148 U
ETS 48
ETS 48
ETS 3148 R
ETS 3148 R
310 260 474 240 95
600 150 700 42 35 12 30
187
SNL 3052
SNL 3052
SNL 3052 TURT
SNL 3052 TURA
TS 52
TNF 52
TSD 3052 U
TSD 3052 U
ETS 52
ETS 52
ETS 3052 R
ETS 3052 R
320 280 516 260 100 650 160 770 50 42 13 36
221
SNL 3152
SNL 3152
SNL 3152 TURT
SNL 3152 TURA
TS 52
TNF 52
TSD 3152 U
TSD 3152 U
ETS 52
ETS 52
ETS 3152 R
ETS 3152 R
320 280 516 260 100 650 160 770 50 42 13 36
221
SNL 3056
SNL 3056
SNL 3056 TURT
SNL 3056 TURA
TS 56
TNF 56
TSD 3056 U
TSD 3056 U
ETS 56
ETS 56
ETS 3056 R
ETS 3056 R
320 280 551 280 105 670 160 790 50 42 16 36
252
SNL 3156
SNL 3156
SNL 3156 TURT
SNL 3156 TURA
TS 56
TNF 56
TSD 3156 U
TSD 3156 U
ETS 56
ETS 56
ETS 3156 R
ETS 3156 R
320 280 551 280 105 670 160 790 50 42 16 36
252
SNL 3060
SNL 3060
SNL 3060 TURT
SNL 3060 TURA
TS 60
TNF 60
TSD 3060 U
TSD 3060 U
ETS 60
ETS 60
ETS 3060 R
ETS 3060 R
350 310 591 300 110 710 190 830 50 42 22 36
301
SNL 3160
SNL 3160
SNL 3160 TURT
SNL 3160 TURA
TS 60
TNF 60
TSD 3160 U
TSD 3160 U
ETS 60
ETS 60
ETS 3160 R
ETS 3160 R
350 310 591 300 110 710 190 830 50 42 22 36
301
SNL 3064
SNL 3064
SNL 3064 TURT
SNL 3064 TURA
TS 64
TNF 64
TSD 3064 U
TSD 3064 U
ETS 64
ETS 64
ETS 3064 R
ETS 3064 R
370 330 631 320 115 750 200 880 50 42 23 36
339
SNL 3164
SNL 3164
SNL 3164 TURT
SNL 3164 TURA
TS 64
TNF 64
TSD 3164 U
TSD 3164 U
ETS 64
ETS 64
ETS 3164 R
ETS 3164 R
300
H2
J1
N1 s
kg
504
End cover
mm
280
H1
Seal
260
Designations
Components
Housing only
da
240
A1
Mass
A4

da 220 300 mm
N
N1
G
J1
H2
J
L
Shaft
Bearing
seating
Width across seals
da
Ca
A2
mm
mm
220
140
360
300
387
148
400
315
148
400
164
240
260
280
300
Eye bolts
According to
DIN 580

Adapter sleeve
Locating rings
CARB bearing
285
M 20
23048 CCK/W33
C 3048 K
OH 3048 H
OH 3048 H
4 FRB 12/360
4 FRB 12/360
404
305
M 24
23148 CCK/W33
C 3148 K
OH 3148 H
OH 3148 HTL
2 FRB 10/400
2 FRB 10/400
315
397
305
M 24
23052 CCK/W33
C 3052 K
OH 3052 H
OH 3052 H
2 FRB 22/400
2 FRB 22/400
440
330
414
315
M 24
23152 CCK/W33
C 3152 K
OH 3152 H
OH 3152 HTL
2 FRB 10/440
2 FRB 10/440
166
420
330
413
315
M 24
23056 CCK/W33
C 3056 K
OH 3056 H
OH 3056 H
6 FRB 10/420
6 FRB 10/420
166
460
330
412
315
M 24
23156 CCK/W33
C 3156 K
OH 3156 H
OH 3156 HTL
2 FRB 10/460
2 FRB 10/460
168
460
330
412
315
M 24
23060 CCK/W33
C 3060 KM
OH 3060 H
OH 3060 H
2 FRB 25/460
2 FRB 25/460
180
500
360
442
345
M 30
23160 CCK/W33
C 3160 K
OH 3160 H
OH 3160 H
2 FRB 10/500
2 FRB 10/500
181
480
360
443
345
M 30
23064 CCK/W33
C 3064 KM
OH 3064 H
OH 3064 H
6 FRB 10/480
6 FRB 10/480
196
540
380
462
365
M 30
23164 CCK/W33
C 3164 KM
OH 3164 H
OH 3164 H
2 FRB 10/540
2 FRB 10/540
Da
A3
A4
mm
505

da 320 400 mm
Ca
Da da
H
s
H1
A3
A1
A
A2
Shaft
Housing
dimensions
mm
320
370 330 631 320 115 750
200
880
50
42
23
36
339
SNL 3068
SNL 3068
SNL 3068 TURT
SNL 3068 TURA
TS 68
TNF 68
TSD 3068 U
TSD 3068 U
ETS 68
ETS 68
ETS 3068 R
ETS 3068 R
400 360 675 340 120 810
220
950
50
42
24
36
430
SNL 3168 F
SNL 3168 F
SNL 3168 FTURT
SNL 3168 FTURA
TS 68
TNF 68
TSD 3168 U
TSD 3168 U
ETS 68
ETS 68
ETS 3168 R
ETS 3168 R
370 330 631 320 115 750
200
880
50
42
23
36
339
SNL 3072
SNL 3072
SNL 3072 TURT
SNL 3072 TURA
TS 72
TNF 72
TSD 3072 U
TSD 3072 U
ETS 72
ETS 72
ETS 3072 R
ETS 3072 R
400 360 695 350 120 840
220
1 000
50
42
30
36
458
SNL 3172 F
SNL 3172 F
SNL 3172 FTURT
SNL 3172 FTURA
TS 72
TNF 72
TSD 3172 U
TSD 3172 U
ETS 72
ETS 72
ETS 3172 R
ETS 3172 R
400 360 675 340 120 810
220
950
50
42
24
36
430
SNL 3076 F
SNL 3076 F
SNL 3076 FTURT
SNL 3076 FTURA
TS 76
TNF 76
TSD 3076 U
TSD 3076 U
ETS 76
ETS 76
ETS 3076 R
ETS 3076 R
400 360 715 360 120 870
220
1 040
50
42
30
36
473
SNL 3176 F
SNL 3176 F
SNL 3176 FTURT
SNL 3176 FTURA
TS 76
TNF 76
TSD 3176 U
TSD 3176 U
ETS 76
ETS 76
ETS 3176 R
ETS 3176 R
400 360 695 350 120 840
220
1 000
50
42
30
36
458
SNL 3080 F
SNL 3080 F
SNL 3080 FTURT
SNL 3080 FTURA
TS 80
TNF 80
TSD 3080 U
TSD 3080 U
ETS 80
ETS 80
ETS 3080 R
ETS 3080 R
430 390 775 380 125 950
240
1 120
60
48
30
42
595
SNL 3180 F
SNL 3180 F
SNL 3180 FTURT
SNL 3180 FTURA
TS 80
TNF 80
TSD 3180 U
TSD 3180 U
ETS 80
ETS 80
ETS 3180 R
ETS 3180 R
400 360 715 360 120 870
220
1 040
50
42
30
36
473
SNL 3084 F
SNL 3084 F
SNL 3084 FTURT
SNL 3084 FTURA
TS 84
TNF 84
TSD 3084 U
TSD 3084 U
ETS 84
ETS 84
ETS 3084 R
ETS 3084 R
460 420 810 410 130 1 000 260
1 170
60
48
35
42
716
SNL 3184 F
SNL 3184 F
SNL 3184 FTURT
SNL 3184 FTURA
TS 84
TNF 84
TSD 3184 U
TSD 3184 U
ETS 84
ETS 84
ETS 3184 R
ETS 3184 R
400
H2
J1
N1
G
kg
506
End cover
mm
380
H1
Seal
360
Designations
Components
Housing only
da
340
A1
Mass
A4

da 320 400 mm
N
N1
G
J1
H2
J
L
Shaft
Bearing
seating
Width across seals
da
Ca
A2
mm
mm
320
197
520
380
461
190
580
410
198
540
192
340
360
380
400
Eye bolts
According to
DIN 580

Adapter sleeve
Locating rings
CARB bearing
365
M 30
23068 CCK/W33
C 3068 KM
OH 3068 H
OH 3068 H
4 FRB 16/520
4 FRB 16/520
491
395
M 30
23168 CCK/W33
C 3168 KM
OH 3168 H
OH 3168 H
380
461
365
M 30
23072 CCK/W33
C 23072 KM
OH 3072 H
OH 3072 H
4 FRB 16/540
4 FRB 16/540
600
410
491
395
M 36
23172 CCK/W33
C 3172 KM
OH 3172 H
OH 3172 H
135
560
410
492
395
M 30
23076 CCK/W33
C 3076 KM
OH 3076 H
OH 3076 H
194
620
410
491
395
M 36
23176 CAK/W33
C 3176 KMB1
OH 3176 H
OH 3176 HE
148
600
410
492
395
M 36
23080 CCK/W33
C 3080 KM
OH 3080 H
OH 3080 H
200
650
440
521
425
M 42
23180 CAK/W33
C 3180 KMB
OH 3180 H
OH 3180 HE
150
620
410
492
395
M 36
23084 CAK/W33
C 3084 KM
OH 3084 H
OH 3084 H
224
700
470
551
455
M 42
23184 CKJ/W33
C 3184 KM
OH 3184 H
OH 3184 H
Da
A3
A4
mm
1
For missing locating ring data, please contact SKF Applications Engineering.
507

da 410 470 mm
Ca
Da da
H
s
H1
A3
A1
A
A2
Shaft Housing
dimensions
da
A1
Mass
H
H1
H2
J1
N1
A4
Designations
Components
Housing only
Seal
End cover
mm
mm
410
430
390 775 380 125
950
240
1 120
60
48
30
42
595
SNL 3088 F
SNL 3088 F
SNL 3088 FTURT
SNL 3088 FTURA
TS 88
TNF 88
TSD 3088 U
TSD 3088 U
ETS 88
ETS 88
ETS 3088 R
ETS 3088 R
460
430 835 420 135
1 030 260
1 220
60
48
35
42
755
SNL 3188 F
SNL 3188 F
SNL 3188 FTURT
SNL 3188 FTURA
TS 88
TNF 88
TSD 3188 U
TSD 3188 U
ETS 88
ETS 88
ETS 3188 R
ETS 3188 R
460
420 810 410 130
1 000 260
1 170
60
48
35
42
716
SNL 3092 F
SNL 3092 F
SNL 3092 FTURT
SNL 3092 FTURA
TS 92
TNF 92
TSD 3092 U
TSD 3092 U
ETS 92
ETS 92
ETS 3092 R
ETS 3092 R
470
440 880 440 145
1 070 260
1 280
60
48
35
42
865
SNL 3192 F
SNL 3192 F
SNL 3192 FTURT
SNL 3192 FTURA
TS 92
TNF 92
TSD 3192 U
TSD 3192 U
ETS 92
ETS 92
ETS 3192 R
ETS 3192 R
460
420 810 410 130
1 000 260
1 170
60
48
35
42
716
SNL 3096 F
SNL 3096 F
SNL 3096 FTURT
SNL 3096 FTURA
TS 96
TNF 96
TSD 3096 U
TSD 3096 U
ETS 96
ETS 96
ETS 3096 R
ETS 3096 R
470
440 920 460 155
1 110 260
1 330
70
56
35
48
947
SNL 3196 F
SNL 3196 F
SNL 3196 FTURT
SNL 3196 FTURA
TS 96
TNF 96
TSD 3196 U
TSD 3196 U
ETS 96
ETS 96
ETS 3196 R
ETS 3196 R
460
430 835 420 135
1 030 260
1 220
60
48
35
42
755
SNL 30/500 F
SNL 30/500 F
SNL 30/500 FTURT
SNL 30/500 FTURA
TS 500
TNF 500
TSD 30/500 U
TSD 30/500 U
ETS 500
ETS 500
ETS 30/500 R
ETS 30/500 R
430
450
470
kg
508

da 410 470 mm
N
N1
G
J1
H2
J
L
Shaft
Bearing
seating
Width across seals
da
Ca
A2
mm
mm
410
157
650
440
522
226
720
470
163
680
240
430
450
470
Eye bolts
According to
DIN 580

Adapter sleeve
Locating rings
CARB bearing
425
M 42
23088 CAK/W33
C 3088 KMB
OH 3088 H
OH 3088 HE
552
455
M 42
23188 CAK/W33
C 3188 KMB1
OH 3188 H
OH 3188 HE
470
552
455
M 42
23092 CAK/W33
C 3092 KM
OH 3092 H
OH 3092 H
760
480
562
465
M 48
23192 CAK/W33
C 3192 KM
OH 3192 H
OH 3192 H
165
700
470
561
455
M 42
23096 CAK/W33
C 3096 KM
OH 3096 H
OH 3096 H
248
790
480
561
465
M 48
23196 CAK/W33
C 3196 KMB1
OH 3196 H
OH 3196 HE
167
720
470
551
455
M 42
230/500 CAK/W33
C 30/500 KM
OH 30/500 H
OH 30/500 H
Da
A3
A4
mm
1
509

da 170 300 mm
Ca
Da db da
H
s
H1
Shaft
Housing
dimensions
430 100 510 34 28 14 24
69.5
SNL 3134 G
SNL 3134 G
TS 40
TNF 40
ETS 40
ETS 40
180
230 180 333 170 70
430 100 510 34 28 14 24
69.5
SNL 3036 G
SNL 3036 G
TS 44
TNF 44
ETS 44
ETS 44
240 190 353 180 75
450 110 530 34 28 15 24
77.5
SNL 3136 G
SNL 3136 G
TS 44
TNF 44
ETS 44
ETS 44
240 190 353 180 75
450 110 530 34 28 15 24
77.5
SNL 3038 G
SNL 3038 G
TS 44
TNF 44
ETS 44
ETS 44
260 210 375 190 80
480 120 560 34 28 10 24
97.5
SNL 3138 G
SNL 3138 G
TS 44
TNF 44
ETS 44
ETS 44
260 210 375 190 80
480 120 560 34 28 10 24
97.5
SNL 3040 G
SNL 3040 G
TS 48
TNF 48
ETS 48
ETS 48
280 230 411 210 85
510 130 610 42 35 10 30
123
SNL 3140 G
SNL 3140 G
TS 48
TNF 48
ETS 48
ETS 48
280 230 411 210 85
510 130 610 42 35 10 30
123
SNL 3044 G
SNL 3044 G
TS 52
TNF 52
ETS 52
ETS 52
290 240 434 220 90
540 140 640 42 35 12 30
138
SNL 3144 G
SNL 3144 G
TS 52
TNF 52
ETS 52
ETS 52
290 240 434 220 90
540 140 640 42 35 12 30
138
SNL 3048 G
SNL 3048 G
TS 56
TNF 56
ETS 56
ETS 56
310 260 474 240 95
600 150 700 42 35 12 30
187
SNL 3148 G
SNL 3148 G
TS 56
TNF 56
ETS 56
ETS 56
310 260 474 240 95
600 150 700 42 35 12 30
187
SNL 3052 G
SNL 3052 G
TS 60
TNF 60
ETS 60
ETS 60
320 280 516 260 100 650 160 770 50 42 13 36
221
SNL 3152 G
SNL 3152 G
TS 60
TNF 60
ETS 60
ETS 60
320 280 516 260 100 650 160 770 50 42 13 36
221
SNL 3056 G
SNL 3056 G
TS 64
TNF 64
ETS 64
ETS 64
320 280 551 280 105 670 160 790 50 42 16 36
252
SNL 3156 G
SNL 3156 G
TS 64
TNF 64
ETS 64
ETS 64
320 280 551 280 105 670 160 790 50 42 16 36
252
SNL 3060 G
SNL 3060 G
TS 68
TNF 68
ETS 68
ETS 68
350 310 591 300 110 710 190 830 50 42 22 36
301
SNL 3160 G
SNL 3160 G
TS 68
TNF 68
ETS 68
ETS 68
300
N1 s
kg
510
End cover
230 180 333 170 70
280
J1
Seal
170
260
Designations
Components
Housing only
mm
240
H2
Taconite seals
TNF design
mm
220
H1
Labyrinth seals
TS design
200
A3
da
190
A1
Mass
A1
A
A2

da 170 300 mm
N
N1
G
J1
H2
J
L
Shaft
da
db
mm
Bearing
seating
Width across
seals
Ca
A2
Da
mm
Eye bolts
According to
DIN 580

Locating rings
CARB bearing
A3
mm
170
180
108
280
240
302
M 16
23134 CC/W33
2 FRB 10/280
180
200
108
280
240
304
M 16
200
116
300
250
317
M 16
23036 CC/W33
24036 CC/W33
C 3036
23136 CC/W33
C 3136
2 FRB 17/280
2 FRB 4/280
2 FRB 17/280
2 FRB 10/300
2 FRB 10/300
200
115
290
250
318
M 16
200
124
320
270
334
M 20
23038 CC/W33
24038 CC/W33
C 3038
23138 CC/W33
4 FRB 10/290
2 FRB 7.5/290
4 FRB 10/290
2 FRB 10/320
220
122
310
270
331
M 20
220
132
340
290
351
M 20
23040 CC/W33
24040 CC/W33
C 3040
23140 CC/W33
C 3140
4 FRB 10/310
2 FRB 6.5/310
4 FRB 10/310
2 FRB 10/340
2 FRB 10/340
240
130
340
290
353
M 20
240
140
370
300
361
M 20
23044 CC/W33
24044 CC/W33
C 3044
23144 CC/W33
C 3144
4 FRB 10/340
2 FRB 6/340
4 FRB 10/340
2 FRB 10/370
2 FRB 10/370
260
140
360
300
387
M 20
260
148
400
315
404
M 24
23048 CC/W33
24048 CC/W33
C 3048
23148 CC/W33
C 3148
4 FRB 12/360
2 FRB 11/360
4 FRB 12/360
2 FRB 10/400
2 FRB 10/400
280
148
400
315
397
M 24
280
164
440
330
414
M 24
23052 CC/W33
24052 CC/W33
C 3052
23152 CC/W33
C 3152
2 FRB 22/400
2 FRB 4/400
2 FRB 22/400
2 FRB 10/440
2 FRB 10/440
300
166
420
330
413
M 24
300
166
460
330
412
M 24
23056 CC/W33
24056 CC/W33
C 3056
23156 CC/W33
C 3156
6 FRB 10/420
2 FRB 13/420
6 FRB 10/420
2 FRB 10/460
2 FRB 10/460
320
168
460
330
412
M 24
320
180
500
360
442
M 30
23060 CC/W33
24060 CC/W33
C 3060
23160 CC/W33
C 3160
2 FRB 25/460
2 FRB 4/460
2 FRB 25/460
2 FRB 10/500
2 FRB 10/500
190
200
220
240
260
280
300
511

da 320 460 mm
Ca
Da db da
H
s
H1
Shaft
A1
A
A2
A3
Labyrinth seals
TS design
Taconite seals
TNF design
Housing
dimensions
mm
320
350 310 591 300
110
710
190
830
50
42
22
36
301
SNL 3064 G
SNL 3064 G
TS 72
TNF 72
ETS 72
ETS 72
370 330 631 320
115
750
200
880
50
42
23
36
339
SNL 3164 G
SNL 3164 G
TS 72
TNF 72
ETS 72
ETS 72
370 330 631 320
115
750
200
880
50
42
23
36
339
SNL 3068 G
SNL 3068 G
TS 76
TNF 76
ETS 76
ETS 76
400 360 675 340
120
810
220
950
50
42
24
36
430
427
SNL 3168 GF
SNL 3168 GL
TS 76
ETS 76
370 330 631 320
115
750
200
880
50
42
23
36
339
SNL 3072 G
SNL 3072 G
TS 80
TNF 80
ETS 80
ETS 80
400 360 695 350
120
840
220
1 000
50
42
30
36
458
454
SNL 3172 GF
SNL 3172 GL
TS 80
ETS 80
400 360 675 340
120
810
220
950
50
42
24
36
430
427
SNL 3076 GF
SNL 3076 GL
TS 84
ETS 84
400 360 715 360
120
870
220
1 040
50
42
30
36
473
470
SNL 3176 GF
SNL 3176 GL
TS 84
ETS 84
400 360 695 350
120
840
220
1 000
50
42
30
36
458
454
SNL 3080 GF
SNL 3080 GL
TS 92
ETS 92
430 390 775 380
125
950
240
1 120
60
48
30
42
595
595
SNL 3180 GF
SNL 3180 GL
TS 92
ETS 92
400 360 715 360
120
870
220
1 040
50
42
30
36
473
470
SNL 3084 GF
SNL 3084 GL
TS 96
ETS 96
460 420 810 410
130
1 000 260
1 170
60
48
35
42
716
709
SNL 3184 GF
SNL 3184 GL
TS 96
ETS 96
430 390 775 380
125
950
240
1 120
60
48
30
42
595
595
SNL 3088 GF
SNL 3088 GL
TS 500
ETS 500
460 430 835 420
135
1 030 260
1 220
60
48
35
42
755
751
SNL 3188 GF
SNL 3188 GL
TS 500
ETS 500
460 420 810 410
130
1 000 260
1 170
60
48
35
42
716
709
SNL 3092 GF
SNL 3092 GL
TS 530
ETS 530
470 440 880 440
145
1 070 260
1 280
60
48
35
42
865
859
SNL 3192 GF
SNL 3192 GL
TS 530
ETS 530
400
420
440
460
H2
J1
N1
G
kg
512
End cover
mm
380
H1
Seal
360
Designations
Components
Housing only
da
340
A1
Mass

da 320 460 mm
N
N1
G
J1
H2
J
L
Shaft
da
db
mm
320
340
360
380
400
420
440
460
Bearing
seating
Width across
seals
Ca
A2
Da
mm
Eye bolts
According to
DIN 580

Locating rings
CARB bearing
23064 CC/W33
24064 CC/W33
C 3064 M
23164 CC/W33
C 3164 M
6 FRB 10/480
2 FRB 10.5/480
6 FRB 10/480
2 FRB 10/540
2 FRB 10/540
23068 CC/W33
24068 CC/W33
C 3068 M
23168 CC/W33
4 FRB 16/520
2 FRB 8.5/520
4 FRB 16/520
A3
mm
340
181
480
360
443
M 30
340
196
540
380
462
M 30
360
197
520
380
461
M 30
360
190
210
580
410
491
M 30
380
198
540
380
461
M 30
23072 CC/W33
24072 CC/W33
4 FRB 16/540
2 FRB 9/540
380
192
212
600
410
491
M 36
23172 CC/W33
400
135
180
560
410
492
M 30
23076 CC/W33
400
194
214
620
410
491
M 36
23176 CA/W33
430
148
192
600
410
492
M 36
23080 CC/W33
430
200
220
650
440
521
M 42
23180 CA/W33
450
150
194
620
410
492
M 36
23084 CA/W33
450
224
244
700
470
551
M 42
23184 CJ/W33
470
157
200
650
440
522
M 42
23088 CA/W33
470
226
246
720
470
552
M 42
23188 CA/W33
500
163
224
680
470
552
M 42
23092 CA/W33
500
240
260
760
480
562
M 48
23192 CA/W33
513

da 480 500 mm
Ca
Da db da
H
s
H1
Shaft
Housing
dimensions
A1
A1
A
A2
A3
Labyrinth seals
TS design
Taconite seals
TNF design
Mass
da
H1
H2
J1
mm
mm
480
460 420 810 410 130 1 000 260
1 170 60
48
35
42
716
709
470 440 920 460 155 1 110 260
1 330 70
56
35
48
500
460 430 835 420 135 1 030 260
1 220 60
48
35
530
470 440 920 460 155 1 110 260
1 330 70
56
35
N1
Seal
End cover
SNL 3096 GF
SNL 3096 GL
TS 530/510
ETS 530
947
941
SNL 3196 GF
SNL 3196 GL
TS 560/520
ETS 560
42
745
751
SNL 30/500 GF
SNL 30/500 GL
TS 560
ETS 560
48
947
941
SNL 30/530 GF
SNL 30/530 GL
TS 600
ETS 600
kg
514
Designations
Components
Housing only

da 480 500 mm
N
N1
G
J1
H2
J
L
Shaft
da
db
mm
480
Bearing
seating
Width across
seals
Ca
A2
Da
mm
Eye bolts
According to
DIN 580

Locating rings
CARB bearing
A3
mm
510
165
224
700
470
561
M 42
23096 CA/W33
520
248
268
790
480
561
M 48
23196 CA/W33
500
530
167
226
720
470
551
M 42
230/500 CA/W33
530
560
185
248
780
480
551
M 48
230/530 CA/W33
For missing locating ring data please contact SKF Applications Engineering.
515
Accessories (metric series)
Bearing accessories
Adapter and withdrawal sleeves
Adapter and withdrawal sleeves are used to
secure bearings having a tapered bore on to
cyIindrical shaft seatings. They facilitate bearing
mounting and dismounting and often simplify
bearing arrangement design. Adapter sleeves are
the more popular as they enable bearings to be
mounted on straight shafts (Figure 1) as well as
stepped shafts (Figure 2). They are easier to
mount than the withdrawal sleeves (Figure 3)
and require no additional location on the shaft.
When using adapter sleeves on straight shafts
it is possible to locate the bearing at any position
on the shaft. When used on stepped shafts
together with a support ring, exact axial positioning of the bearing can be achieved and bearing
dismounting is facilitated.
Bearings on withdrawal sleeves must be
mounted against a fixed abutment, for example,
a shaft shoulder. The withdrawal sleeve must
be secured in position after it has been pressed
into the bearing bore by a lock nut or plate on
the shaft.
Figure 1
Straight shaft mounting

with adapter sleeve
516
As adapter and withdrawal sleeves adapt

to the shaft diameter, less stringent shaft
tolerances can be permitted. However, the accuracy of form the running accuracy of the bearing
arrangement. Generally, seatings machined to
tolerance h9 and having a cylindricity tolerance
to IT5/2 will be satisfactory.
Adapter and withdrawal sleeves for

oil injection
The requisite interference fit of the bearing on
the shaft is achieved by pressing the bearing up
on to the adapter sleeve, or by pressing the
withdrawal sleeve into the bearing bore. The
force required to do this may be considerable,
particularly where large bearings are concerned,
because of the friction of the mating surfaces in
the bearing/sleeve and sleeve/shaft contacts.
Figure 2
Shouldered shaft mounting

with adapter sleeve
To facilitate the use of the oil injection method

for mounting and dismounting, larger SKF
adapter and withdrawal sleeves are available
with oil supply ducts and distribution grooves. If
oil is injected and pressure maintained via these
ducts and grooves between the sleeve and bearing bore and between the sleeve and shaft, friction in the contacts will be reduced, and the force
required for mounting and dismounting will be
considerably smaller than for mounting in the
dry state.
The oil injection equipment required for this
method is also available from SKF; please refer
to SKF Maintenance and Lubrication Products
Catalog (711-639). When using the oil injection
method and equipment, the prescribed precautionary measures should be observed.
Figure 3
Withdrawal sleeve mount

on a stepped shaft
Bearing accessories
Adapter sleeves
SKF adapter sleeves (Figure 4) are supplied
complete with lock nut and locking device. The
sleeves have a slotted design and an external
taper of 1:12. Up to size 40, the sleeves are
phosphated; the larger sleeves are not surface
treated but are oiled.
The dimensions of the metric adapter sleeves
conform to ISO 2982-1:1995. Adapter sleeves
with inch dimensions are in accordance with
ANSI/ABMA std 8.2.
Withdrawal sleeves
Adapter sleeves for oil injection
SKF metric adapter sleeves with a bore diameter of 140 mm and above are supplied with oil
supply ducts and distributor grooves for pressurized oil (Figure 5). Ducts and grooves are
optional for inch dimension sleeves of 778" and
above. The following four types are available:
OH
OH ..B
OH .. H
OH .. HB
Oil injected between bearing and

sleeve. One oil supply duct from
large end of sleeve.
Oil injected between bearing,
sleeve and shaft. Sizes 32 to 40:
one oil supply duct from large end
of sleeve. Size 44 and larger:
two oil supply ducts from large
end of sleeve.
Oil injected between bearing and
sleeve. One oil supply duct from
nut side of sleeve.
Oil injected between bearing,
sleeve and shaft. Sizes 32 to 40:
one oil supply duct from nut side
of sleeve. Size 44 and larger:
two oil supply ducts from nut
side of sleeve.
For metric adapter sleeves the dimensions of

the oil injection holes are shown in the table.
For corresponding information on inch
dimension adapter sleeves, please consult SKF
Figure 4
Figure 5
SKF withdrawal sleeves (Figure 6) are coated

with a preservative. They are slotted and have
an external taper of 1:12, except for those of
series AH 240 and AH 241, which have an
external taper of 1:30 and are designed for use
with the wide spherical roller bearings of series
240 K30 and 241 K30.
The dimensions of the metric withdrawal
sleeves are in accordance with ISO 29821:1995. Prefix X indicates that the sleeve has
been modified and suffix G indicates that the
thread pitch diameter G has been changed to
adopt to the ISO standard.
The nuts required for dismounting are not
supplied with the sleeves and must be ordered
separately.
Withdrawal sleeves for oil injection

SKF metric sleeves having a bore diameter of
200 mm and above are supplied as standard in
the AOH design, which enables the oil injection
method to be used.
AOH withdrawal sleeves (Figure 7) have two
oil supply ducts at the threaded side and have
distribution grooves around the circumference
and in the axial direction on the outside surface
as well as in the bore.
The tables give the thread data for the supply
ducts to take the oil injection equipment, which
can be supplied by SKF.
Figure 6
Figure 7
517

Bearing accessories
Lock nuts
SKF can supply a wide range of sizes of
lock nuts, which are also referred to as shaft or
withdrawal nuts, depending on the use to which
they are put. They are used to locate bearings
and other components on shafts as well as to
facilitate mounting and dismounting bearings on
withdrawal sleeves, adapter sleeves or tapered
journals.
SKF lock nuts have four (Figure 8) or eight
(Figure 9) equally spaced slots around the outside diameter to allow the use of hook, impact
or HNM spanners.
Metric lock nuts up to and including size 40
(KM and KML designs) have a metric ISO thread
to tolerance 5H, ISO 965/III-1980, while the
larger nuts from size 42 have a metric ISO
trapezoidal thread to tolerance 7H, ISO 29011977. It is recommended that the mating
thread on the shaft be made to tolerance 6g
according to ISO 965/III-1980 for the smaller
nuts and to tolerance 7e according to ISO
2901-1977 for those with trapezoidal thread.
518
Inch-size lock nuts up to and including a thread

diameter of 12.562" have a thread of American
National Form NS Class 3. Larger inch sizes
have an Acme Class 3G, General Purpose
thread. The mating inch thread on the shaft
must be of the same form and tolerance as that
of the nut.
The dimensions of the metric lock nuts are in
accordance with ISO 2982-2:1995. The inch
series nuts are in accordance with ANSI/ABMA
std 8.2.
Locking washers, locking

clips and locking plates
Locking washers (Figure 10) of the MB, MBL
and W designs are used with the smaller nuts,
while locking clips (Figure 11) of the MS design
and locking plates of the P design are used with
larger nuts. They engage a groove in the shaft
and lock the nut in position. Locking washers of
the MB .. A design are used when a washer with
increased strength is needed.
The locking washers are made of deep drawn
steel strip. Dimensions of the metric sizes,
except those of the MB .. A designs, conform to
ISO 2982-2:1995. Inch-size locking washers
are in accordance with ANSI/ABMA std 8.2.
The locking clips and plates are also made of
deep drawn steel strip. They are attached to the
shaft nut using a screw with hexagonal head to
DIN EN 24017:1992. The screw and a spring
washer (to DIN 128) are supplied with the clips.
Locking plates type P are supplied with a steel
wire to be passed through the holes in the head
of each screw. The ends of the wire should be
twisted together, to prevent loosening of the
screws.
Figure 8
Figure 10
Figure 9
Figure 11
Bearing accessories
Other accessories
In addition to the selection of accessories shown
in this publication, SKF can also supply a wide
variety of other aids for mounting and dismounting rolling bearings. These include dollies,
drifts, mechanical tools such as drive-up kits
and pullers, oil pumps with accessories, complete oil injection tool kits, heating tools, electrical withdrawal tools, gauges and other items.
Further details can be found in the SKF
Maintenance and Lubrication Products catalog
(711-639).
A carefully selected range of lubricating
greases is also available to cover the majority of
applications where grease lubricated bearings
are used.
519

Adapter sleeves
d1 17 55 mm
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
mm
Designations
Adapter sleeve
with lock nut
and locking
device
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
17
20
32
32
32
24
28
31
7
7
7
M 20x1
M 20x1
M 20x1
0.036
0.04
0.05
H 204
H 304
H 2304
KM 4
KM 4
KM 4
MB 4
MB 4
MB 4
1204 EK
2204 EK, 1304 EK
2304 K
20
25
38
38
38
38
26
29
29
35
8
8
8
8
M 25x1.5
M 25x1.5
M 25x1.5
M 25x1.5
0.064
0.071
0.071
0.085
H 205
H 305
H 305 C
H 2305
KM 5
KM 5
KM 5
KM 5
MB 5
MB 5
MB 5 C
MB 5
1205 EK
2205 EK, 1305 EK, 22205 EK
2205 E-2RS1K
2305 K
25
30
45
45
45
45
27
31
31
38
8
8
8
8
M 30x1.5
M 30x1.5
M 30x1.5
M 30x1.5
0.086
0.095
0.095
0.11
H 206
H 306
H 306 C
H 2306
KM 6
KM 6
KM 6
KM 6
MB 6
MB 6
MB 6 C
MB 6
1206 EK
2206 EK, 1306 EK, 22206 EK
2206 E-2RS1K
2306 K
30
35
52
52
52
52
29
35
35
43
9
9
9
9
M 35x1.5
M 35x1.5
M 35x1.5
M 35x1.5
0.12
0.14
0.14
0.16
H 207
H 307
H 307 C
H 2307
KM 7
KM 7
KM 7
KM 7
MB 7
MB 7
MB 7 C
MB 7
1207 EK
2207 EK, 1307 EK, 22207 EK
2207 E-2RS1K
2307 EK
35
40
58
58
31
36
10
10
M 40x1.5
M 40x1.5
0.16
0.17
H 208
H 308
KM 8
KM 8
MB 8
MB 8
58
58
36
46
10
10
M 40x1.5
M 40x1.5
0.17
0.22
H 308 C
H 2308
KM 8
KM 8
MB 8 C
MB 8
1208 EK
2208 EK, 1308 EK, 22208 EK,
21308 CCK
2208 E-2RS1K
2308 EK, 22308 EK
65
65
33
39
11
11
M 45x1.5
M 45x1.5
0.21
0.23
H 209
H 309
KM 9
KM 9
MB 9
MB 9
65
65
39
50
11
11
M 45x1.5
M 45x1.5
0.23
0.27
H 309 C
H 2309
KM 9
KM 9
MB 9 C
MB 9
70
70
35
42
12
12
M 50x1.5
M 50x1.5
0.24
0.27
H 210
H 310
KM 10
KM 10
MB 10
MB 10
HMV 10
HMV 10
70
70
42
55
12
12
M 50x1.5
M 50x1.5
0.27
0.34
H 310 C
H 2310
KM 10
KM 10
MB 10 C
MB 10
HMV 10
75
75
37
45
12.5
12.5
M 55x2
M 55x2
0.28
0.32
H 211
H 311
KM 11
KM 11
MB 11
MB 11
HMV 11
HMV 11
75
75
45
59
12.5
12.5
M 55x2
M 55x2
0.32
0.39
H 311 C
H 2311
KM 11
KM 11
MB 11 C
MB 11
HMV 11
80
80
38
47
13
13
M 60x2
M 60x2
0.31
0.36
H 212
H 312
KM 12
KM 12
MB 12
MB 12
HMV 12
HMV 12
80
62
13
M 60x2
0.45
H 2312
KM 12
MB 12
HMV 12
40
45
50
55
45
50
55
60
520
1209 EK
2209 EK, 1309 EK, 22209 EK,
21309 CCK
2209 E-2RS1K
2309 EK, 22309 EK
1210 EK
2210 EK, 1310 EK, 22210 EK,
21310 CCK
2210-2RS1K
2310 K, 22310 EK
1211 EK
2211 EK, 1311 EK, 22211 EK,
21311 CCK
2211 E-2RS1K
2311 K, 22311 EK
1212 EK
2212 EK, 1312 EK, 22212 EK,
21312 CCK
2312 K, 22312 EK
Adapter sleeves
d1 60 110 mm
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
mm
60
Designations
Adapter sleeve
with lock nut
and locking
device
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
65
85
85
85
40
50
65
14
14
14
M 65x2
M 65x2
M 65x2
0.36
0.42
0.52
H 213
H 313
H 2313
KM 13
KM 13
KM 13
MB 13
MB 13
MB 13
HMV 13
HMV 13
1213 EK
2213 EK,1313 EK, 22213 EK, 21313 CCK
2313 K, 22313 EK
70
92
92
52
68
14
14
M 70x2
M 70x2
0.67
0.88
H 314
H 2314
KM 14
KM 14
MB 14
MB 14
HMV 14
HMV 14
22214 EK, 21314 CCK

22314 EK
65
75
98
98
98
43
55
73
15
15
15
M 75x2
M 75x2
M 75x2
0.66
0.78
1.1
H 215
H 315
H 2315
KM 15
KM 15
KM 15
MB 15
MB 15
MB 15
HMV 15
HMV 15
HMV 15
1215 K
2215 K, 1315 K, 22215 EK, 21315 CCK
2315 K, 22315 EK
70
80
105 46
105 59
105 78
17
17
17
M 80x2
M 80x2
M 80x2
0.81
0.95
1.2
H 216
H 316
H 2316
KM 16
KM 16
KM 16
MB 16
MB 16
MB 16
HMV 16
HMV 16
HMV 16
1216 K
2216 EK, 1316 K, 22216 EK, 21316 CCK
2316 K, 22316 EK
75
85
110 50
110 63
110 82
18
18
18
M 85x2
M 85x2
M 85x2
0.94
1.1
1.35
H 217
H 317
H 2317
KM 17
KM 17
KM 17
MB 17
MB 17
MB 17
HMV 17
HMV 17
HMV 17
1217 K
2217 K, 1317 K, 22217 EK, 21317 CCK
2317 K, 22317 EK
80
90
120 52
120 65
120 86
18
18
18
M 90x2
M 90x2
M 90x2
1.1
1.3
1.6
H 218
H 318
H 2318
KM 18
KM 18
KM 18
MB 18
MB 18
MB 18
HMV 18
HMV 18
HMV 18
1218 K
2218 K, 1318 K, 22218 EK, 21318 CCK
2318 K, 23218 CCK/W33, 22318 EK
85
95
125 55
125 68
125 90
19
19
19
M 95x2
M 95x2
M 95x2
1.25
1.4
1.8
H 219
H 319
H 2319
KM 19
KM 19
KM 19
MB 19
MB 19
MB 19
HMV 19
HMV 19
HMV 19
1219 K
2219 K, 1319 K, 22219 EK, 21319 CCK
2319 K, 22319 EK
90
100 130
130
130
130
58
71
97
76
20
20
20
20
M 100x2
M 100x2
M 100x2
M 100x2
1.4
1.6
2
1.8
H 220
H 320
H 2320
H 3120
KM 20
KM 20
KM 20
KM 20
MB 20
MB 20
MB 20
MB 20
HMV 20
HMV 20
HMV 20
HMV 20
1220 K
2220 K, 1320 K, 22220 EK, 21320 CCK
2320 K, 23220 CCK/W33, 22320 EK
23120 CCK/W33
95
105 140 60
140 74
20
20
M 105x2
M 105x2
1.6
1.85
H 221
H 321
KM 21
KM 21
MB 21
MB 21
HMV 21
HMV 21
1221 K
2221 K, 1321 K
100
110 145 63
145 77
21
21
M 110x2
M 110x2
1.8
2.05
H 222
H 322
KM 22
KM 22
MB 22
MB 22
HMV 22
HMV 22
145 105 21
145 81 21
M 110x2
M 110x2
2.75
2.1
H 2322
H 3122
KM 22
KM 22
MB 22
MB 22
HMV 22
HMV 22
1222 K
2222 K, 1322 K, 23022 CCK,
22222 EK, 21322 CCK
2322 K, 23222 CCK/W33, 22322 EK
23122 CCK/W33
22
22
M 120x2
M 120x2
1.7
1.8
H 3924
H 3024
KML 24
KML 24
MBL 24
MBL 24
HMV 24
HMV 24
23924 CCK/W33
1224 K, 23024 CCK/W33
155 88 22
155 112 22
M 120x2
M 120x2
2.5
3
H 3124
H 2324
KM 24
KM 24
MB 24
MB 24
HMV 24
HMV 24
23124 CCK/W33, 22224 EK

23224 CCK/W33, 22324 CCK/W33
110
120 145 60
145 72
521

Adapter sleeves
d1 115 140 mm
Type OH . . H
Type OH . . HB
Size 40 and under
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
B4
G1
mm
115 130
125 140
135 150
140 160
Type OH . . B
Size 40 and under
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23926 CCK/W33
23026 CCK/W33
23126 CCK/W33,
22226 EK
23226 CCK/W33,
22326 CCK/W33
155
155
165
65
80
92
23
23
23
M 130x2
M 130x2
M 130x2
2.4
2.8
3.45
H 3926
H 3026
H 3126
KML 26
KML 26
KM 26
MBL 26
MBL 26
MB 26
HMV 26
HMV 26
HMV 26
165
121
23
M 130x2
4.45
H 2326
KM 26
MB 26
HMV 26
165
165
180
66
82
97
24
24
24
M 140x2
M 140x2
M 140x2
2.7
3.05
4.1
H 3928
H 3028
H 3128
KML 28
KML 28
KM 28
MBL 28
MBL 28
MB 28
HMV 28
HMV 28
HMV 28
180
131
24
M 140x2
5.4
H 2328
KM 28
MB 28
HMV 28
180
180
195
76
87
111
26
26
26
M 150x2
M 150x2
M 150x2
3.6
3.75
5.25
H 3930
H 3030
H 3130
KML 30
KML 30
KM 30
MBL 30
MBL 30
MB 30
HMV 30
HMV 30
HMV 30
195
139
26
M 150x2
6.4
H 2330
KM 30
MB 30
HMV 30
190
190
190
190
190
78
78
78
78
78
27.5
27.5
27.5
27.5
27.5
9
9
9
9
4.2
4.2
5
5
M 160x3
M 160x3
M 160x3
M 160x3
M 160x3
M6
M6
M6
M6
4.6
4.6
4.6
4.6
4.6
H 3932
OH 3932 H
OH 3932 HB
OH 3932
OH 3932 B
KML 32
KML 32
KML 32
KML 32
KML 32
MBL 32
MBL 32
MBL 32
MBL 32
MBL 32
HMV 32
HMV 32
HMV 32
HMV 32
HMV 32
23932 CCK/W33
23932 CCK/W33
23932 CCK/W33
23932 CCK/W33
23932 CCK/W33
190
190
190
190
190
93
93
93
93
93
27.5
27.5
27.5
27.5
27.5
9
9
9
9
4.2
4.2
5
5
M 160x3
M 160x3
M 160x3
M 160x3
M 160x3
M6
M6
M6
M6
5.1
5.1
5.1
5.1
5.1
H 3032
OH 3032 H
OH 3032 HB
OH 3032
OH 3032 B
KML 32
KML 32
KML 32
KML 32
KML 32
MBL 32
MBL 32
MBL 32
MBL 32
MBL 32
HMV 32
HMV 32
HMV 32
HMV 32
HMV 32
23032 CCK/W33
23032 CCK/W33
23032 CCK/W33
23032 CCK/W33
23032 CCK/W33
210
119
28
M 160x3
7.25
H 3132
KM 32
MB 32
HMV 32
210
119
28
4.2
M 160x3
M6
7.25
OH 3132 H
KM 32
MB 32
HMV 32
210
119
28
4.2
M 160x3
M6
7.25
OH 3132 HB
KM 32
MB 32
HMV 32
210
119
28
13
6.8
M 160x3
G 1/8
7.25
OH 3132
KM 32
MB 32
HMV 32
210
119
28
13
6.8
M 160x3
G 1/8
7.25
OH 3132 B
KM 32
MB 32
HMV 32
23132 CCK/W33,
22232 CCK/W33
23132 CCK/W33,
22232 CCK/W33
23132 CCK/W33,
22232 CCK/W33
23132 CCK/W33,
22232 CCK/W33
23132 CCK/W33,
22232 CCK/W33
522
Type OH
23928 CCK/W33
23028 CCK/W33
23128 CCK/W33,
22228 CCK/W33
23228 CCK/W33,
22328 CCK/W33
23930 CCK/W33
23030 CCK/W33
23130 CCK/W33,
22230 CCK/W33
23230 CCK/W33,
22330 CCK/W33
Adapter sleeves
d1 140 150 mm
Type OH . . H
Type OH
Type OH . . HB
Size 40 and under
Type H
MB locking device
Type OH . . B
Size 40 and under
Dimensions
d1
Mass
d3
B1
B2
B4
G1
mm
140 160
(cont.)
150 170
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23232 CCK/W33,
22332 CCK/W33
23232 CCK/W33,
22332 CCK/W33
23232 CCK/W33,
22332 CCK/W33
23232 CCK/W33,
22332 CCK/W33
23232 CCK/W33,
22332 CCK/W33
210
147
28
M 160x3
8.8
H 2332
KM 32
MB 32
HMV 32
210
147
28
4.2
M 160x3
M6
8.8
OH 2332 H
KM 32
MB 32
HMV 32
210
147
28
4.2
M 160x3
M6
8.8
OH 2332 HB
KM 32
MB 32
HMV 32
210
147
28
13
M 160x3
G 1/8
8.8
OH 2332
KM 32
MB 32
HMV 32
210
147
28
13
M 160x3
G 1/8
8.8
OH 2332 B
KM 32
MB 32
HMV 32
200
200
200
200
200
79
79
79
79
79
28.5
28.5
28.5
28.5
28.5
9
9
9
9
4.2
4.2
5
5
M 170x3
M 170x3
M 170x3
M 170x3
M 170x3
M6
M6
M6
M6
5
5
5
5
5
H 3934
OH 3934 H
OH 3934 HB
OH 3934
OH 3934 B
KML 34
KML 34
KML 34
KML 34
KML 34
MBL 34
MBL 34
MBL 34
MBL 34
MBL 34
HMV 34
HMV 34
HMV 34
HMV 34
HMV 34
23934 CCK/W33
23934 CCK/W33
23934 CCK/W33
23934 CCK/W33
23934 CCK/W33
200
200
200
200
200
101
101
101
101
101
28.5
28.5
28.5
28.5
28.5
9
9
9
9
4.2
4.2
5
5
M 170x3
M 170x3
M 170x3
M 170x3
M 170x3
M6
M6
M6
M6
5.8
5.8
5.8
5.8
5.8
H 3034
OH 3034 H
OH 3034 HB
OH 3034
OH 3034 B
KML 34
KML 34
KML 34
KML 34
KML 34
MBL 34
MBL 34
MBL 34
MBL 34
MBL 34
HMV 34
HMV 34
HMV 34
HMV 34
HMV 34
23034 CCK/W33
23034 CCK/W33
23034 CCK/W33
23034 CCK/W33
23034 CCK/W33
220
122
29
M 170x3
8.1
H 3134
KM 34
MB 34
HMV 34
220
122
29
4.2
M 170x3
M6
8.1
OH 3134 H
KM 34
MB 34
HMV 34
220
122
29
4.2
M 170x3
M6
8.1
OH 3134 HB
KM 34
MB 34
HMV 34
220
122
29
13
M 170x3
G 1/8
8.1
OH 3134
KM 34
MB 34
HMV 34
220
122
29
13
M 170x3
G 1/8
8.1
OH 3134 B
KM 34
MB 34
HMV 34
220
154
29
M 170x3
9.9
H 2334
KM 34
MB 34
HMV 34
220
154
29
4.2
M 170x3
M6
9.9
OH 2334 H
KM 34
MB 34
HMV 34
220
154
29
4.2
M 170x3
M6
9.9
OH 2334 HB
KM 34
MB 34
HMV 34
220
154
29
13
M 170x3
G 1/8
9.9
OH 2334
KM 34
MB 34
HMV 34
220
154
29
13
M 170x3
G 1/8
9.9
OH 2334 B
KM 34
MB 34
HMV 34
23134 CCK/W33,
22234 CCK/W33
23134 CCK/W33,
22234 CCK/W33
23134 CCK/W33,
22234 CCK/W33
23134 CCK/W33,
22234 CCK/W33
23134 CCK/W33,
22234 CCK/W33
23234 CCK/W33,
22334 CCK/W33
23234 CCK/W33,
22334 CCK/W33
23234 CCK/W33,
22334 CCK/W33
23234 CCK/W33,
22334 CCK/W33
23234 CCK/W33,
22334 CCK/W33
523

Adapter sleeves
d1 160 170 mm
Type OH . . H
Type OH . . HB
Size 40 and under
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
B4
G1
mm
160 180
170 190
Type OH . . B
Size 40 and under
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
210
210
210
210
210
87
87
87
87
87
29.5
29.5
29.5
29.5
29.5
9
9
9
9
4.2
4.2
5
5
M 180x3
M 180x3
M 180x3
M 180x3
M 180x3
M6
M6
M6
M6
5.7
5.7
5.7
5.7
5.7
H 3936
OH 3936 H
OH 3936 HB
OH 3936
OH 3936 B
KML 36
KML 36
KML 36
KML 36
KML 36
MBL 36
MBL 36
MBL 36
MBL 36
MBL 36
HMV 36
HMV 36
HMV 36
HMV 36
HMV 36
23936 CCK/W33
23936 CCK/W33
23936 CCK/W33
23936 CCK/W33
23936 CCK/W33
210
210
210
210
210
109
109
109
109
109
29.5
29.5
29.5
29.5
29.5
9
9
9
9
4.2
4.2
5
5
M 180x3
M 180x3
M 180x3
M 180x3
M 180x3
M6
M6
M6
M6
6.7
6.7
6.7
6.7
6.7
H 3036
OH 3036 H
OH 3036 HB
OH 3036
OH 3036 B
KML 36
KML 36
KML 36
KML 36
KML 36
MBL 36
MBL 36
MBL 36
MBL 36
MBL 36
HMV 36
HMV 36
HMV 36
HMV 36
HMV 36
23036 CCK/W33
23036 CCK/W33
23036 CCK/W33
23036 CCK/W33
23036 CCK/W33
230
131
30
M 180x3
9.15
H 3136
KM 36
MB 36
HMV 36
230
131
30
4.2
M 180x3
M6
9.15
OH 3136 H
KM 36
MB 36
HMV 36
230
131
30
4.2
M 180x3
M6
9.15
OH 3136 HB
KM 36
MB 36
HMV 36
230
131
30
13
M 180x3
G 1/8
9.15
OH 3136
KM 36
MB 36
HMV 36
230
131
30
13
M 180x3
G 1/8
9.15
OH 3136 B
KM 36
MB 36
HMV 36
230
161
30
M 180x3
11
H 2336
KM 36
MB 36
HMV 36
230
161
30
4.2
M 180x3
M6
11
OH 2336 H
KM 36
MB 36
HMV 36
230
161
30
4.2
M 180x3
M6
11
OH 2336 HB
KM 36
MB 36
HMV 36
230
161
30
13
M 180x3
G 1/8
11
OH 2336
KM 36
MB 36
HMV 36
230
161
30
13
M 180x3
G 1/8
11
OH 2336 B
KM 36
MB 36
HMV 36
23136 CCK/W33,
22236 CCK/W33
23136 CCK/W33,
22236 CCK/W33
23136 CCK/W33,
22236 CCK/W33
23136 CCK/W33,
22236 CCK/W33
23136 CCK/W33,
22236 CCK/W33
23236 CCK/W33,
22336 CCK/W33
23236 CCK/W33,
22336 CCK/W33
23236 CCK/W33,
22336 CCK/W33
23236 CCK/W33,
22336 CCK/W33
23236 CCK/W33,
22336 CCK/W33
220
220
220
220
220
89
89
89
89
89
30.5
30.5
30.5
30.5
30.5
9
9
9
9
4.2
4.2
5
5
M 190x3
M 190x3
M 190x3
M 190x3
M 190x3
M6
M6
M6
M6
6.2
6.2
6.2
6.2
6.2
H 3938
OH 3938 H
OH 3938 HB
OH 3938
OH 3938 B
KML 38
KML 38
KML 38
KML 38
KML 38
MBL 38
MBL 38
MBL 38
MBL 38
MBL 38
HMV 38
HMV 38
HMV 38
HMV 38
HMV 38
23938 CCK/W33
23938 CCK/W33
23938 CCK/W33
23938 CCK/W33
23938 CCK/W33
220
220
220
220
220
112
112
112
112
112
30.5
30.5
30.5
30.5
30.5
9
9
9
9
4.2
4.2
5
5
M 190x3
M 190x3
M 190x3
M 190x3
M 190x3
M6
M6
M6
M6
7.25
7.25
7.25
7.25
7.25
H 3038
OH 3038 H
OH 3038 HB
OH 3038
OH 3038 B
KML 38
KML 38
KML 38
KML 38
KML 38
MBL 38
MBL 38
MBL 38
MBL 38
MBL 38
HMV 38
HMV 38
HMV 38
HMV 38
HMV 38
23038 CCK/W33
23038 CCK/W33
23038 CCK/W33
23038 CCK/W33
23038 CCK/W33
524
Type OH
Adapter sleeves
d1 170 180 mm
Type OH . . H
Type OH
Type OH . . HB
Size 40 and under
Type H
MB locking device
Type OH . . B
Size 40 and under
Dimensions
d1
Mass
d3
B1
B2
B4
G1
mm
170 190
(cont.)
180 200
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23138 CCK/W33,
22238 CCK/W33
23138 CCK/W33,
22238 CCK/W33
23138 CCK/W33,
22238 CCK/W33
23138 CCK/W33,
22238 CCK/W33
23138 CCK/W33,
22238 CCK/W33
240
141
31
M 190x3
10.5
H 3138
KM 38
MB 38
HMV 38
240
141
31
4.2
M 190x3
M6
10.5
OH 3138 H
KM 38
MB 38
HMV 38
240
141
31
4.2
M 190x3
M6
10.5
OH 3138 HB
KM 38
MB 38
HMV 38
240
141
31
13
M 190x3
G 1/8
10.5
OH 3138
KM 38
MB 38
HMV 38
240
141
31
13
M 190x3
G 1/8
10.5
OH 3138 B
KM 38
MB 38
HMV 38
240
169
31
M 190x3
12
H 2338
KM 38
MB 38
HMV 38
240
169
31
4.2
M 190x3
M6
12
OH 2338 H
KM 38
MB 38
HMV 38
240
169
31
4.2
M 190x3
M6
12
OH 2338 HB
KM 38
MB 38
HMV 38
240
169
31
13
M 190x3
G 1/8
12
OH 2338
KM 38
MB 38
HMV 38
240
169
31
13
M 190x3
G 1/8
12
OH 2338 B
KM 38
MB 38
HMV 38
240
240
240
240
240
98
98
98
98
98
31.5
31.5
31.5
31.5
31.5
9
9
9
9
4.2
4.2
5
5
M 200x3
M 200x3
M 200x3
M 200x3
M 200x3
M6
M6
M6
M6
7.9
7.9
7.9
7.9
7.9
H 3940
OH 3940 H
OH 3940 HB
OH 3940
OH 3940 B
KML 40
KML 40
KML 40
KML 40
KML 40
MBL 40
MBL 40
MBL 40
MBL 40
MBL 40
HMV 40
HMV 40
HMV 40
HMV 40
HMV 40
23940 CCK/W33
23940 CCK/W33
23940 CCK/W33
23940 CCK/W33
23940 CCK/W33
240
240
240
240
240
120
120
120
120
120
31.5
31.5
31.5
31.5
31.5
9
9
13
13
4.2
4.2
7
7
M 200x3
M 200x3
M 200x3
M 200x3
M 200x3
M6
M6
-
G 1/8
G 1/8
8.9
8.9
8.9
8.9
8.9
H 3040
OH 3040 H
OH 3040 HB
OH 3040
OH 3040 B
KML 40
KML 40
KML 40
KML 40
KML 40
MBL 40
MBL 40
MBL 40
MBL 40
MBL 40
HMV 40
HMV 40
HMV 40
HMV 40
HMV 40
23040 CCK/W33
23040 CCK/W33
23040 CCK/W33
23040 CCK/W33
23040 CCK/W33
250
150
32
M 200x3
12
H 3140
KM 40
MB 40
HMV 40
250
150
32
4.2
M 200x3
M6
12
OH 3140 H
KM 40
MB 40
HMV 40
250
150
32
4.2
M 200x3
M6
12
OH 3140 HB
KM 40
MB 40
HMV 40
250
150
32
13
7.5
M 200x3
G 1/8
12
OH 3140
KM 40
MB 40
HMV 40
250
150
32
13
7.5
M 200x3
G 1/8
12
OH 3140 B
KM 40
MB 40
HMV 40
23140 CCK/W33,
22240 CCK/W33
23140 CCK/W33,
22240 CCK/W33
23140 CCK/W33,
22240 CCK/W33
23140 CCK/W33,
22240 CCK/W33
23140 CCK/W33,
22240 CCK/W33
23238 CCK/W33,
22338 CCK/W33
23238 CCK/W33,
22338 CCK/W33
23238 CCK/W33,
22338 CCK/W33
23238 CCK/W33,
22338 CCK/W33
23238 CCK/W33,
22338 CCK/W33
525

Adapter sleeves
d1 180 200 mm
Type OH
Type OH . . H
Type OH . . HB
Size 44 to 56
Type H
MS locking device
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
180 200
(Cont.)
200 220
M 200x3
Designations
Adapter sleeve
with lock nut
and locking
device
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23240 CCK/W33,
22340 CCK/W33
23240 CCK/W33,
22340 CCK/W33
23240 CCK/W33,
22340 CCK/W33
23240 CCK/W33,
22340 CCK/W33
23240 CCK/W33,
22340 CCK/W33
in
kg
13.5
H 2340
KM 40
MB 40
HMV 40
250 176
32
250 176
32
4.2 M 200x3
M6
13.5
OH 2340 H
KM 40
MB 40
HMV 40
250 176
32
4.2 M 200x3
M6
13.5
OH 2340 HB
KM 40
MB 40
HMV 40
250 176
32
13
M 200x3
G 1/8
13.5
OH 2340
KM 40
MB 40
HMV 40
250 176
32
13
M 200x3
G 1/8
13.5
OH 2340 B
KM 40
MB 40
HMV 40
260
260
260
260
260
96
96
96
96
96
30
30
30
30
30
41
41
41
41
41
9
9
9
9
-
4.2
4.2
5
5
-
Tr
Tr
Tr
Tr
Tr
220x4
220x4
220x4
220x4
220x4
M6
M6
M6
M6
-
7.95
7.95
7.95
7.95
7.95
OH 3944 H
OH 3944 HB
OH 3944
OH 3944 B
H 3944
HM 3044
HM 3044
HM 3044
HM 3044
HM 3044
MS 3044
MS 3044
MS 3044
MS 3044
MS 3044
HMV 44
HMV 44
HMV 44
HMV 44
HMV 44
23944 CCK/W33
23944 CCK/W33
23944 CCK/W33
23944 CCK/W33
23944 CCK/W33
260
260
260
260
260
126
126
126
126
126
30
30
30
30
30
41
41
41
41
41
9
9
13
13
-
4.2
4.2
7
7
-
Tr
Tr
Tr
Tr
Tr
220x4
220x4
220x4
220x4
220x4
M6
M6
-
G 1/8
G 1/8
-
9.90
9.90
9.90
9.90
9.90
OH 3044 H
OH 3044 HB
OH 3044
OH 3044 B
H 3044
HM 3044
HM 3044
HM 3044
HM 3044
HM 3044
MS 3044
MS 3044
MS 3044
MS 3044
MS 3044
HMV 44
HMV 44
HMV 44
HMV 44
HMV 44
23044 CCK/W33
23044 CCK/W33
23044 CCK/W33
23044 CCK/W33
23044 CCK/W33
280 161
35
4.2 Tr 220x4
M6
15.0
OH 3144 H
HM 44 T
MB 44
HMV 44
280 161
35
4.2 Tr 220x4
M6
15.0
OH 3144 HB
HM 44 T
MB 44
HMV 44
280 161
35
13
Tr 220x4
G 1/8
15.0
OH 3144
HM 44 T
MB 44
HMV 44
280 161
35
13
Tr 220x4
G 1/8
15.0
OH 3144 B
HM 44 T
MB 44
HMV 44
280 161
35
Tr 220x4
15.0
H 3144
HM 44 T
MB 44
HMV 44
23144 CCK/W33,
22244 CCK/W33
23144 CCK/W33,
22244 CCK/W33
23144 CCK/W33,
22244 CCK/W33
23144 CCK/W33,
22244 CCK/W33
23144 CCK/W33,
22244 CCK/W33
280 186
35
4.2 Tr 220x4
M6
17.0
OH 2344 H
HM 44 T
MB 44
HMV 44
280 186
35
4.2 Tr 220x4
M6
17.0
OH 2344 HB
HM 44 T
MB 44
HMV 44
280 186
35
13
8.5 Tr 220x4
G 1/8
17.0
OH 2344
HM 44 T
MB 44
HMV 44
280 186
35
13
8.5 Tr 220x4
G 1/8
17.0
OH 2344 B
HM 44 T
MB 44
HMV 44
280 186
35
17.0
H 2344
HM 44 T
MB 44
HMV 44
Tr 220x4
526
Type OH . . B
Size 44 to 56
Type OH . . B
Size 40 and under
Type OH . . HB
Size 40 and under
23244 CCK/W33,
22344 CCK/W33
23244 CCK/W33,
22344 CCK/W33
23244 CCK/W33,
22344 CCK/W33
23244 CCK/W33,
22344 CCK/W33
23244 CCK/W33,
22344 CCK/W33
Adapter sleeves
d1 220 240 mm
Type OH
Type OH . . H
Type OH . . HB
Size 44 to 56
Type H
MS locking device
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
220 240
240 260
Type OH . . B
Size 44 to 56
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
290
290
290
290
290
101
101
101
101
101
34
34
34
34
34
46
46
46
46
46
9
9
13
13
-
4.2
4.2
6.5
6.5
-
Tr 240x4
Tr 240x4
Tr 240x4
Tr 240x4
Tr 240x4
M6
M6
-
G 1/8
G 1/8
-
11
11
11
11
11
OH 3948 H
OH 3948 HB
OH 3948
OH 3948 B
H 3948
HM 3048
HM 3048
HM 3048
HM 3048
HM 3048
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
HMV 48
HMV 48
HMV 48
HMV 48
HMV 48
23948 CCK/W33
23948 CCK/W33
23948 CCK/W33
23948 CCK/W33
23948 CCK/W33
290
290
290
290
290
133
133
133
133
133
34
34
34
34
34
46
46
46
46
46
9
9
13
13
-
4.2
4.2
7
7
-
Tr 240x4
Tr 240x4
Tr 240x4
Tr 240x4
Tr 240x4
M6
M6
-
G 1/8
G 1/8
-
12
12
12
12
12
OH 3048 H
OH 3048 HB
OH 3048
OH 3048 B
H 3048
HM 3048
HM 3048
HM 3048
HM 3048
HM 3048
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
HMV 48
HMV 48
HMV 48
HMV 48
HMV 48
23048 CCK/W33
23048 CCK/W33
23048 CCK/W33
23048 CCK/W33
23048 CCK/W33
300 172
37
4.2 Tr 240x4
M6
16
OH 3148 H
HM 48 T
MB 48
HMV 48
300 172
37
4.2 Tr 240x4
M6
16
OH 3148 HB
HM 48 T
MB 48
HMV 48
300 172
37
13
Tr 240x4
G 1/8
16
OH 3148
HM 48 T
MB 48
HMV 48
300 172
37
13
Tr 240x4
G 1/8
16
OH 3148 B
HM 48 T
MB 48
HMV 48
300 172
37
Tr 240x4
16
H 3148
HM 48 T
MB 48
HMV 48
23148 CCK/W33,
22248 CCK/W33
23148 CCK/W33,
22248 CCK/W33
23148 CCK/W33,
22248 CCK/W33
23148 CCK/W33,
22248 CCK/W33
23148 CCK/W33,
22248 CCK/W33
300 199
37
4.2 Tr 240x4
M6
19
OH 2348 H
HM 48 T
MB 48
HMV 48
300 199
37
4.2 Tr 240x4
M6
19
OH 2348 HB
HM 48 T
MB 48
HMV 48
300 199
37
13
9.5 Tr 240x4
G 1/8
19
OH 2348
HM 48 T
MB 48
HMV 48
300 199
37
13
9.5 Tr 240x4
G 1/8
19
OH 2348 B
HM 48 T
MB 48
HMV 48
300 199
37
Tr 240x4
19
H 2348
HM 48 T
MB 48
HMV 48
310
310
310
310
310
116
116
116
116
116
34
34
34
34
34
46
46
46
46
46
9
9
13
13
-
4.2
4.2
7
7
-
Tr 260x4
Tr 260x4
Tr 260x4
Tr 260x4
Tr 260x4
M6
M6
-
G 1/8
G 1/8
-
11.7
11.7
11.7
11.7
11.7
OH 3952 H
OH 3952 HB
OH 3952
OH 3952 B
H 3952
HM 3052
HM 3052
HM 3052
HM 3052
HM 3052
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
HMV 52
HMV 52
HMV 52
HMV 52
HMV 52
23952 CCK/W33
23952 CCK/W33
23952 CCK/W33
23952 CCK/W33
23952 CCK/W33
310
310
310
310
310
145
145
145
145
145
34
34
34
34
34
46
46
46
46
46
9
9
13
13
-
4.2
4.2
7.5
7.5
-
Tr 260x4
Tr 260x4
Tr 260x4
Tr 260x4
Tr 260x4
M6
M6
-
G 1/8
G 1/8
-
13.5
13.5
13.5
13.5
13.5
OH 3052 H
OH 3052 HB
OH 3052
OH 3052 B
H 3052
HM 3052
HM 3052
HM 3052
HM 3052
HM 3052
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
MS 3052-48
HMV 52
HMV 52
HMV 52
HMV 52
HMV 52
23052 CCK/W33
23052 CCK/W33
23052 CCK/W33
23052 CCK/W33
23052 CCK/W33
23248 CCK/W33,
22348 CCK/W33
23248 CCK/W33,
22348 CCK/W33
23248 CCK/W33,
22348 CCK/W33
23248 CCK/W33,
22348 CCK/W33
23248 CCK/W33,
22348 CCK/W33
527

Adapter sleeves
d1 240 260 mm
Type OH
Type OH . . H
Type OH . . HB
Size 44 to 56
Type H
MS locking device
Type H
MB locking device
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
240 260
(Cont.)
260 280
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23152 CCK/W33,
22252 CACK/W33
23152 CCK/W33,
22252 CACK/W33
23152 CCK/W33,
22252 CACK/W33
23152 CCK/W33,
22252 CACK/W33
23152 CCK/W33,
22252 CACK/W33
330 190
39
4.2 Tr 260x4
M6
21
OH 3152 H
HM 52 T
MB 52
HMV 52
330 190
39
4.2 Tr 260x4
M6
21
OH 3152 HB
HM 52 T
MB 52
HMV 52
330 190
39
13
Tr 260x4
G 1/8
21
OH 3152
HM 52 T
MB 52
HMV 52
330 190
39
13
Tr 260x4
G 1/8
21
OH 3152 B
HM 52 T
MB 52
HMV 52
330 190
39
Tr 260x4
21
H 3152
HM 52 T
MB 52
HMV 52
330 211
39
4.2 Tr 260x4
M6
23
OH 2352 H
HM 52 T
MB 52
HMV 52
330 211
39
4.2 Tr 260x4
M6
23
OH 2352 HB
HM 52 T
MB 52
HMV 52
330 211
39
13
Tr 260x4
G 1/8
23
OH 2352
HM 52 T
MB 52
HMV 52
330 211
39
13
Tr 260x4
G 1/8
23
OH 2352 B
HM 52 T
MB 52
HMV 52
330 211
39
Tr 260x4
23
H 2352
HM 52 T
MB 52
HMV 52
330
330
330
330
330
121
121
121
121
121
38
38
38
38
38
50
50
50
50
50
9
9
13
13
-
4.2
4.2
7
7
-
Tr 280x4
Tr 280x4
Tr 280x4
Tr 280x4
Tr 280x4
M6
M6
-
G 1/8
G 1/8
-
15.3
15.3
15.3
15.3
15.3
OH 3956 H
OH 3956 HB
OH 3956
OH 3956 B
H 3956
HM 3056
HM 3056
HM 3056
HM 3056
HM 3056
MS 3056
MS 3056
MS 3056
MS 3056
MS 3056
HMV 56
HMV 56
HMV 56
HMV 56
HMV 56
23956 CCK/W33
23956 CCK/W33
23956 CCK/W33
23956 CCK/W33
23956 CCK/W33
330
330
330
330
330
152
152
152
152
152
38
38
38
38
38
50
50
50
50
50
9
9
13
13
-
4.2
4.2
7.5
7.5
-
Tr 280x4
Tr 280x4
Tr 280x4
Tr 280x4
Tr 280x4
M6
M6
-
G 1/8
G 1/8
-
16
16
16
16
16
OH 3056 H
OH 3056 HB
OH 3056
OH 3056 B
H 3056
HM 3056
HM 3056
HM 3056
HM 3056
HM 3056
MS 3056
MS 3056
MS 3056
MS 3056
MS 3056
HMV 56
HMV 56
HMV 56
HMV 56
HMV 56
23056 CCK/W33
23056 CCK/W33
23056 CCK/W33
23056 CCK/W33
23056 CCK/W33
350 195
41
4.2 Tr 280x4
M6
23
OH 3156 H
HM 56 T
MB 56
HMV 56
350 195
41
4.2 Tr 280x4
M6
23
OH 3156 HB
HM 56 T
MB 56
HMV 56
350 195
41
13
Tr 280x4
G 1/8
23
OH 3156
HM 56 T
MB 56
HMV 56
350 195
41
13
Tr 280x4
G 1/8
23
OH 3156 B
HM 56 T
MB 56
HMV 56
350 195
41
Tr 280x4
23
H 3156
HM 56 T
MB 56
HMV 56
23156 CCK/W33,
22256 CACK/W33
23156 CCK/W33,
22256 CACK/W33
23156 CCK/W33,
22256 CACK/W33
23156 CCK/W33,
22256 CACK/W33
23156 CCK/W33,
22256 CACK/W33
528
Designations
Adapter sleeve
with lock nut
and locking
device
Type OH . . B
Size 44 to 56
23252 CACK/W33,
22352 CCK/W33
23252 CACK/W33,
22352 CCK/W33
23252 CACK/W33,
22352 CCK/W33
23252 CACK/W33,
22352 CCK/W33
23252 CACK/W33,
22352 CCK/W33
Adapter sleeves
d1 260 300 mm
Type OH . . H
Type H
MS locking device
Type H
MB locking device
Mass
d3
B1
B2
B3
B4 A
G1
mm
260 280
(cont.)
280 300
300 320
Type OH . . HB
Size 60 and over
Type OH . . HB
Size 44 to 56
Dimensions
d1
Type OH
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Type OH . . B
Size 60 and over
Type OH . . B
Size 44 to 56
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
23256 CACK/W33,
22356 CCK/W33
23256 CACK/W33,
22356 CCK/W33
23256 CACK/W33,
22356 CCK/W33
23256 CACK/W33,
22356 CCK/W33
23256 CACK/W33,
22356 CCK/W33
350 224
41
4.2 Tr 280x4
M6
27
OH 2356 H
HM 56 T
MB 56
HMV 56
350 224
41
4.2 Tr 280x4
M6
27
OH 2356 HB
HM 56 T
MB 56
HMV 56
350 224
41
13
9.5 Tr 280x4
G 1/8
27
OH 2356
HM 56 T
MB 56
HMV 56
350 224
41
13
9.5 Tr 280x4
G 1/8
27
OH 2356 B
HM 56 T
MB 56
HMV 56
350 224
41
Tr 280x4
27
H 2356
HM 56 T
MB 56
HMV 56
360
360
360
360
360
140
140
140
140
140
42
42
42
42
42
54
54
54
54
54
9
9
13
13
-
4.2
4.2
7
7
-
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
M6
M6
-
G 1/8
G 1/8
-
20
20
20
20
20
OH 3960 H
OH 3960 HB
OH 3960
OH 3960 B
H 3960
HM 3060
HM 3060
HM 3060
HM 3060
HM 3060
MS 3060
MS 3060
MS 3060
MS 3060
MS 3060
HMV 60
HMV 60
HMV 60
HMV 60
HMV 60
23960 CCK/W33
23960 CCK/W33
23960 CCK/W33
23960 CCK/W33
23960 CCK/W33
360
360
360
360
360
168
168
168
168
168
42
42
42
42
42
54
54
54
54
54
9
9
13
13
-
4.2
4.2
7.5
7.5
-
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
M6
M6
-
G 1/8
G 1/8
-
20.5
20.5
20.5
20.5
20.5
OH 3060 H
OH 3060 HB
OH 3060
OH 3060 B
H 3060
HM 3060
HM 3060
HM 3060
HM 3060
HM 3060
MS 3060
MS 3060
MS 3060
MS 3060
MS 3060
HMV 60
HMV 60
HMV 60
HMV 60
HMV 60
23060 CCK/W33
23060 CCK/W33
23060 CCK/W33
23060 CCK/W33
23060 CCK/W33
380 208
40
53
4.2 Tr 300x4
M6
29
OH 3160 H
HM 3160
MS 3160
HMV 60
380 208
40
53
4.2 Tr 300x4
M6
29
OH 3160 HB
HM 3160
MS 3160
HMV 60
380 208
40
53
13
Tr 300x4
G 1/8
29
OH 3160
HM 3160
MS 3160
HMV 60
380 208
40
53
13
Tr 300x4
G 1/8
29
OH 3160 B
HM 3160
MS 3160
HMV 60
380 208
40
53
Tr 300x4
29
H 3160
HM 3160
MS 3160
HMV 60
23160 CCK/W33,
22260 CACK/W33
23160 CCK/W33,
22260 CACK/W33
23160 CCK/W33,
22260 CACK/W33
23160 CCK/W33,
22260 CACK/W33
23160 CCK/W33,
22260 CACK/W33
380
380
380
380
380
240
240
240
240
240
40
40
40
40
40
53
53
53
53
53
9
9
15
15
-
4.2
4.2
9
9
-
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
M6
M6
-
G 1/4
G 1/4
-
32
32
32
32
32
OH 3260 H
OH 3260 HB
OH 3260
OH 3260 B
H 3260
HM 3160
HM 3160
HM 3160
HM 3160
HM 3160
MS 3160
MS 3160
MS 3160
MS 3160
MS 3160
HMV 60
HMV 60
HMV 60
HMV 60
HMV 60
23260 CACK/W33
23260 CACK/W33
23260 CACK/W33
23260 CACK/W33
23260 CACK/W33
380
380
380
380
380
140
140
140
140
140
42
42
42
42
42
55
55
55
55
55
9
9
13
13
-
4
4
7
7
-
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
M6
M6
-
G 1/8
G 1/8
-
21.5
21.5
21.5
21.5
21.5
OH 3964 H
OH 3964 HB
OH 3964
OH 3964 B
H 3964
HM 3064
HM 3064
HM 3064
HM 3064
HM 3064
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
HMV 64
HMV 64
HMV 64
HMV 64
HMV 64
23964 CACK/W33
23964 CACK/W33
23964 CACK/W33
23964 CACK/W33
23964 CACK/W33
529

Adapter sleeves
d1 300 320 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
300 320
(cont.)
320 340
380
380
380
380
380
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
171
171
171
171
171
42
42
42
42
42
55
55
55
55
55
9
9
13
13
-
4
4
7.5
7.5
-
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
M6
M6
-
G 1/8
G 1/8
-
22
22
22
22
22
OH 3064 H
OH 3064 HB
OH 3064
OH 3064 B
H 3064
HM 3064
HM 3064
HM 3064
HM 3064
HM 3064
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
HMV 64
HMV 64
HMV 64
HMV 64
HMV 64
23064 CCK/W33
23064 CCK/W33
23064 CCK/W33
23064 CCK/W33
23064 CCK/W33
400 226
42
56
Tr 320x5
M6
32
OH 3164 H
HM 3164
MS 3164
HMV 64
400 226
42
56
Tr 320x5
M6
32
OH 3164 HB
HM 3164
MS 3164
HMV 64
400 226
42
56
13
9.5 Tr 320x5
G 1/8
32
OH 3164
HM 3164
MS 3164
HMV 64
400 226
42
56
13
9.5 Tr 320x5
G 1/8
32
OH 3164 B
HM 3164
MS 3164
HMV 64
400 226
42
56
Tr 320x5
32
H 3164
HM 3164
MS 3164
HMV 64
23164 CCK/W33,
22264 CACK/W33
23164 CCK/W33,
22264 CACK/W33
23164 CCK/W33,
22264 CACK/W33
23164 CCK/W33,
22264 CACK/W33
23164 CCK/W33,
22264 CACK/W33
400
400
400
400
400
258
258
258
258
258
42
42
42
42
42
56
56
56
56
56
9
9
15
15
-
4
4
9
9
-
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
M6
M6
-
G 1/4
G 1/4
-
35
35
35
35
35
OH 3264 H
OH 3264 HB
OH 3264
OH 3264 B
H 3264
HM 3164
HM 3164
HM 3164
HM 3164
HM 3164
MS 3164
MS 3164
MS 3164
MS 3164
MS 3164
HMV 64
HMV 64
HMV 64
HMV 64
HMV 64
23264 CACK/W33
23264 CACK/W33
23264 CACK/W33
23264 CACK/W33
23264 CACK/W33
400
400
400
400
400
144
144
144
144
144
45
45
45
45
45
58
58
58
58
58
9
9
13
13
-
4
4
7
7
-
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
M6
M6
-
G 1/8
G 1/8
-
24.5
24.5
24.5
24.5
24.5
OH 3968 H
OH 3968 HB
OH 3968
OH 3968 B
H 3968
HM 3068
HM 3068
HM 3068
HM 3068
HM 3068
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
23968 CCK/W33
23968 CCK/W33
23968 CCK/W33
23968 CCK/W33
23968 CCK/W33
400
400
400
400
400
187
187
187
187
187
45
45
45
45
45
58
58
58
58
58
9
9
13
13
-
4
4
8
8
-
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
M6
M6
-
G 1/8
G 1/8
-
27
27
27
27
27
OH 3068 H
OH 3068 HB
OH 3068
OH 3068 B
H 3068
HM 3068
HM 3068
HM 3068
HM 3068
HM 3068
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
23068 CCK/W33
23068 CCK/W33
23068 CCK/W33
23068 CCK/W33
23068 CCK/W33
440
440
440
440
440
254
254
254
254
254
55
55
55
55
55
72
72
72
72
72
9
9
15
15
-
4
4
9.5
9.5
-
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
M6
M6
-
G 1/4
G 1/4
-
50
50
50
50
50
OH 3168 H
OH 3168 HB
H 3168
OH 3168 B
H 3168
HM 3168
HM 3168
HM 3168
HM 3168
HM 3168
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
23168 CCK/W33
23168 CCK/W33
23168 CCK/W33
23168 CCK/W33
23168 CCK/W33
440
440
440
440
440
288
288
288
288
288
55
55
55
55
55
72
72
72
72
72
9
9
15
15
-
4
4
10
10
-
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
M6
M6
-
G 1/4
G 1/4
-
51.5
51.5
51.5
51.5
51.5
OH 3268 H
OH 3268 HB
OH 3268
OH 3268 B
H 3268
HM 3168
HM 3168
HM 3168
HM 3168
HM 3168
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
23268 CAK/W33
23268 CAK/W33
23268 CAK/W33
23268 CAK/W33
23268 CAK/W33
530
Designations
Adapter sleeve
with lock nut
and locking
device
Adapter sleeves
d1 340 360 mm
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type H
MS locking device
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
340 360
360 380
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
420
420
420
420
420
144
144
144
144
144
45
45
45
45
45
58
58
58
58
58
9
9
13
13
-
4
4
7
7
-
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
M6
M6
-
G 1/8
G 1/8
-
25.2
25.2
25.2
25.2
25.2
OH 3972 H
OH 3972 HB
OH 3972
OH 3972 B
H 3972
HM 3072
HM 3072
HM 3072
HM 3072
HM 3072
MS 3072
MS 3072
MS 3072
MS 3072
MS 3072
HMV 72
HMV 72
HMV 72
HMV 72
HMV 72
23972 CACK/W33
23972 CACK/W33
23972 CACK/W33
23972 CACK/W33
23972 CACK/W33
420
420
420
420
420
188
188
188
188
188
45
45
45
45
45
58
58
58
58
58
9
9
13
13
-
4
4
8
8
-
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
M6
M6
-
G 1/8
G 1/8
-
29
29
29
29
29
OH 3072 H
OH 3072 HB
OH 3072
OH 3072B
H 3072
HM 3072
HM 3072
HM 3072
HM 3072
HM 3072
MS 3072
MS 3072
MS 3072
MS 3072
MS 3072
HMV 72
HMV 72
HMV 72
HMV 72
HMV 72
23072 CCK/W33
23072 CCK/W33
23072 CCK/W33
23072 CCK/W33
23072 CCK/W33
460
460
460
460
460
259
259
259
259
259
58
58
58
58
58
75
75
75
75
75
9
9
15
15
-
4
4
9.5
9.5
-
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
M6
M6
-
G 1/4
G 1/4
-
56
56
56
56
56
OH 3172 H
OH 3172 HB
OH 3172
OH 3172 B
H 3172
HM 3172
HM 3172
HM 3172
HM 3172
HM 3172
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
HMV 72
HMV 72
HMV 72
HMV 72
HMV 72
23172 CACK/W33
23172 CACK/W33
23172 CACK/W33
23172 CACK/W33
23172 CACK/W33
460
460
460
460
460
299
299
299
299
299
58
58
58
58
58
75
75
75
75
75
9
9
15
15
-
4
4
10
10
-
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
M6
M6
-
G 1/4
G 1/4
-
60.5
60.5
60.5
60.5
60.5
OH 3272 H
OH 3272 HB
OH 3272
OH 3272 B
H 3272
HM 3172
HM 3172
HM 3172
HM 3172
HM 3172
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
MS 3172-68
HMV 72
HMV 72
HMV 72
HMV 72
HMV 72
23272 CAK/W33
23272 CAK/W33
23272 CAK/W33
23272 CAK/W33
23272 CAK/W33
450
450
450
450
450
164
164
164
164
164
48
48
48
48
48
62
62
62
62
62
9
9
13
13
-
4
4
7.5
7.5
-
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
M6
M6
-
G 1/8
G 1/8
-
31.5
31.5
31.5
31.5
31.5
OH 3976 H
OH 3976 HB
OH 3976
OH 3976 B
H 3976
HM 3076
HM 3076
HM 3076
HM 3076
HM 3076
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
HMV 76
HMV 76
HMV 76
HMV 76
HMV 76
23976 CCK/W33
23976 CCK/W33
23976 CCK/W33
23976 CCK/W33
23976 CCK/W33
450
450
450
450
450
193
193
193
193
193
48
48
48
48
48
62
62
62
62
62
9
4
9
4
13 8
13 8
-
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
M6
M6
-
G 1/8
G 1/8
-
35.5
35.5
35.5
35.5
35.5
OH 3076 H
OH 3076 HB
OH 3076
OH 3076 B
H 3076
HM 3076
HM 3076
HM 3076
HM 3076
HM 3076
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
HMV 76
HMV 76
HMV 76
HMV 76
HMV 76
23076 CCK/W33
23076 CCK/W33
23076 CCK/W33
23076 CCK/W33
23076 CCK/W33
490
490
490
490
490
264
264
264
264
264
60
60
60
60
60
77
77
77
77
77
9
9
15
15
-
4
4
9.5
9.5
-
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
M6
M6
-
G 1/4
G 1/4
-
61.5
61.5
61.5
61.5
61.5
OH 3176 H
OH 3176 HB
OH 3176
OH 3176 B
H 3176
HM 3176
HM 3176
HM 3176
HM 3176
HM 3176
MS 3176
MS 3176
MS 3176
MS 3176
MS 3176
HMV 76
HMV 76
HMV 76
HMV 76
HMV 76
23176 CAK/W33
23176 CAK/W33
23176 CAK/W33
23176 CAK/W33
23176 CAK/W33
490
490
490
490
490
310
310
310
310
310
60
60
60
60
60
77
77
77
77
77
9
9
15
15
-
4
4
10.5
10.5
-
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
M6
M6
-
G 1/4
G 1/4
-
69.5
69.5
69.5
69.5
69.5
OH 3276 H
OH 3276 HB
OH 3276
OH 3276 B
H 3276
HM 3176
HM 3176
HM 3176
HM 3176
HM 3176
MS 3176
MS 3176
MS 3176
MS 3176
MS 3176
HMV 76
HMV 76
HMV 76
HMV 76
HMV 76
23276 CAK/W33
23276 CAK/W33
23276 CAK/W33
23276 CAK/W33
23276 CAK/W33
531

Adapter sleeves
d1 380 400 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
380 400
400 420
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
470
470
470
470
470
168
168
168
168
168
52
52
52
52
52
66
66
66
66
66
9
9
13
13
-
4
4
7.5
7.5
-
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
M6
M6
-
G 1/8
G 1/8
-
35
35
35
35
35
OH 3980 H
OH 3980 HB
OH 3980
OH 3980 B
H 3980
HM 3080
HM 3080
HM 3080
HM 3080
HM 3080
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
HMV 80
HMV 80
HMV 80
HMV 80
HMV 80
23980 CACK/W33
23980 CACK/W33
23980 CACK/W33
23980 CACK/W33
23980 CACK/W33
470
470
470
470
470
210
210
210
210
210
52
52
52
52
52
66
66
66
66
66
9
9
13
13
-
4
4
8.5
8.5
-
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
M6
M6
-
G 1/8
G 1/8
-
40
40
40
40
40
OH 3080 H
OH 3080 HB
OH 3080
OH 3080 B
H 3080
HM 3080
HM 3080
HM 3080
HM 3080
HM 3080
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
HMV 80
HMV 80
HMV 80
HMV 80
HMV 80
23080 CACK/W33
23080 CACK/W33
23080 CACK/W33
23080 CACK/W33
23080 CACK/W33
520
520
520
520
520
272
272
272
272
272
62
62
62
62
62
82
82
82
82
82
9
9
15
15
-
4
4
9.5
9.5
-
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
M6
M6
-
G 1/4
G 1/4
-
73
73
73
73
73
OH 3180 H
OH 3180 HB
OH 3180
OH 3180 B
H 3180
HM 3180
HM 3180
HM 3180
HM 3180
HM 3180
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
HMV 80
HMV 80
HMV 80
HMV 80
HMV 80
23180 CAK/W33
23180 CAK/W33
23180 CAK/W33
23180 CAK/W33
23180 CAK/W33
520
520
520
520
520
328
328
328
328
328
62
62
62
62
62
82
82
82
82
82
9
9
15
15
-
4
4
11
11
-
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
M6
M6
-
G 1/4
G 1/4
-
87
87
87
87
87
OH 3280 H
OH 3280 HB
OH 3280
OH 3280 B
H 3280
HM 3180
HM 3180
HM 3180
HM 3180
HM 3180
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
HMV 80
HMV 80
HMV 80
HMV 80
HMV 80
23280 CAK/W33
23280 CAK/W33
23280 CAK/W33
23280 CAK/W33
23280 CAK/W33
490
490
490
490
490
168
168
168
168
168
52
52
52
52
52
66
66
66
66
66
9
9
13
13
-
4
4
7.5
7.5
-
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
M6
M6
-
G 1/8
G 1/8
-
36
36
36
36
36
OH 3984 H
OH 3984 HB
OH 3984
OH 3984B
H 3984
HM 3084
HM 3084
HM 3084
HM 3084
HM 3084
MS 3084
MS 3084
MS 3084
MS 3084
MS 3084
HMV 84
HMV 84
HMV 84
HMV 84
HMV 84
23984 CACK/W33
23984 CACK/W33
23984 CACK/W33
23984 CACK/W33
23984 CACK/W33
490
490
490
490
490
212
212
212
212
212
52
52
52
52
52
66
66
66
66
66
9
9
13
13
-
4
4
8.5
8.5
-
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
M6
M6
-
G 1/8
G 1/8
-
47
47
47
47
47
OH 3084 H
OH 3084 HB
OH 3084
OH 3084 B
H 3084
HM 3084
HM 3084
HM 3084
HM 3084
HM 3084
MS 3084
MS 3084
MS 3084
MS 3084
MS 3084
HMV 84
HMV 84
HMV 84
HMV 84
HMV 84
23084 CAK/W33
23084 CAK/W33
23084 CAK/W33
23084 CAK/W33
23084 CAK/W33
540
540
540
540
540
304
304
304
304
304
70
70
70
70
70
90
90
90
90
90
9
9
15
15
-
4
4
10.5
10.5
-
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
M6
M6
-
G 1/4
G 1/4
-
80
80
80
80
80
OH 3184 H
OH 3184 HB
OH 3184
OH 3184 B
H 3184
HM 3184
HM 3184
HM 3184
HM 3184
HM 3184
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
HMV 84
HMV 84
HMV 84
HMV 84
HMV 84
23184 CK/W33
23184 CK/W33
23184 CK/W33
23184 CK/W33
23184 CK/W33
540
540
540
540
540
352
352
352
352
352
70
70
70
70
70
90
90
90
90
90
9
9
15
15
-
4
4
11
11
-
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
M6
M6
-
G 1/4
G 1/4
96
96
96
96
96
OH 3284 H
OH 3284 HB
OH 3284
OH 3284 B
H 3284
HM 3184
HM 3184
HM 3184
HM 3184
HM 3184
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
MS 3184-80
HMV 84
HMV 84
HMV 84
HMV 84
HMV 84
23284 CAK/W33
23284 CAK/W33
23284 CAK/W33
23284 CAK/W33
23284 CAK/W33
532
Designations
Adapter sleeve
with lock nut
and locking
device
Adapter sleeves
d1 410 430 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
410 440
430 460
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
520
520
520
520
520
189
189
189
189
189
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
10
10
-
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
M8
M8
-
G 1/4
G 1/4
-
58
58
58
58
58
OH 3988 H
OH 3988 HB
OH 3988
OH 3988 B
H 3988
HM 3088
HM 3088
HM 3088
HM 3088
HM 3088
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
HMV 88
HMV 88
HMV 88
HMV 88
HMV 88
23988 CACK/W33
23988 CACK/W33
23988 CACK/W33
23988 CACK/W33
23988 CACK/W33
520
520
520
520
520
228
228
228
228
228
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
11
11
-
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
M8
M8
-
G 1/4
G 1/4
-
65
65
65
65
65
OH 3088 H
OH 3088 HB
OH 3088
OH 3088 B
H 3088
HM 3088
HM 3088
HM 3088
HM 3088
HM 3088
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
HMV 88
HMV 88
HMV 88
HMV 88
HMV 88
23088 CAK/W33
23088 CAK/W33
23088 CAK/W33
23088 CAK/W33
23088 CAK/W33
560
560
560
560
560
307
307
307
307
307
70
70
70
70
70
90
90
90
90
90
12
12
15
15
-
6.5
6.5
14
14
-
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
M8
M8
-
G 1/4
G 1/4
-
95
95
95
95
95
OH 3188 H
OH 3188 HB
OH 3188
OH 3188 B
H 3188
HM 3188
HM 3188
HM 3188
HM 3188
HM 3188
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
HMV 88
HMV 88
HMV 88
HMV 88
HMV 88
23188 CAK/W33
23188 CAK/W33
23188 CAK/W33
23188 CAK/W33
23188 CAK/W33
560
560
560
560
560
361
361
361
361
361
70
70
70
70
70
90
90
90
90
90
12
12
15
15
-
6.5
6.5
16
16
-
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
M8
M8
-
G 1/4
G 1/4
-
117
117
117
117
117
OH 3288 H
OH 3288 HB
OH 3288
OH 3288 B
H 3288
HM 3188
HM 3188
HM 3188
HM 3188
HM 3188
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
HMV 88
HMV 88
HMV 88
HMV 88
HMV 88
23288 CAK/W33
23288 CAK/W33
23288 CAK/W33
23288 CAK/W33
23288 CAK/W33
540
540
540
540
540
189
189
189
189
189
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
10
10
-
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
M8
M8
-
G 1/4
G 1/4
-
60
60
60
60
60
OH 3992 H
OH 3992 HB
OH 3992
OH 3992 B
H 3992
HM 3092
HM 3092
HM 3092
HM 3092
HM 3092
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
HMV 92
HMV 92
HMV 92
HMV 92
HMV 92
23992 CAK/W33
23992 CAK/W33
23992 CAK/W33
23992 CAK/W33
23992 CAK/W33
540
540
540
540
540
234
234
234
234
234
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
11
11
-
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
M8
M8
-
G 1/4
G 1/4
-
71
71
71
71
71
OH 3092 H
OH 3092 HB
OH 3092
OH 3092 B
H 3092
HM 3092
HM 3092
HM 3092
HM 3092
HM 3092
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
HMV 92
HMV 92
HMV 92
HMV 92
HMV 92
23092 CAK/W33
23092 CAK/W33
23092 CAK/W33
23092 CAK/W33
23092 CAK/W33
580
580
580
580
580
326
326
326
326
326
75
75
75
75
75
95
95
95
95
95
12
12
15
15
-
6.5
6.5
14
14
-
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
M8
M8
-
G 1/4
G 1/4
-
119
119
119
119
119
OH 3192 H
OH 3192 HB
OH 3192
OH 3192 B
H 3192
HM 3192
HM 3192
HM 3192
HM 3192
HM 3192
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
HMV 92
HMV 92
HMV 92
HMV 92
HMV 92
23192 CAK/W33
23192 CAK/W33
23192 CAK/W33
23192 CAK/W33
23192 CAK/W33
580
580
580
580
580
382
382
382
382
382
75
75
75
75
75
95
95
95
95
95
12
12
15
15
-
6.5
6.5
17
17
-
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
M8
M8
-
G 1/4
G 1/4
-
134
134
134
134
134
OH 3292 H
OH 3292 HB
OH 3292
OH 3292 B
H 3292
HM 3192
HM 3192
HM 3192
HM 3192
HM 3192
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
MS 3192-88
HMV 92
HMV 92
HMV 92
HMV 92
HMV 92
23292 CAK/W33
23292 CAK/W33
23292 CAK/W33
23292 CAK/W33
23292 CAK/W33
533

Adapter sleeves
d1 450 470 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
450 480
470 500
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
560
560
560
560
560
200
200
200
200
200
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
10
10
-
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
M8
M8
-
G 1/4
G 1/4
-
66
66
66
66
66
OH 3996 H
OH 3996 HB
OH 3996
OH 3996 B
H 3996
HM 3096
HM 3096
HM 3096
HM 3096
HM 3096
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
HMV 96
HMV 96
HMV 96
HMV 96
HMV 96
23996 CAK/W33
23996 CAK/W33
23996 CAK/W33
23996 CAK/W33
23996 CAK/W33
560
560
560
560
560
237
237
237
237
237
60
60
60
60
60
77
77
77
77
77
12
12
15
15
-
6.5
6.5
11
11
-
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
M8
M8
-
G 1/4
G 1/4
-
75
75
75
75
75
OH 3096 H
OH 3096 HB
OH 3096
OH 3096 B
H 3096
HM 3096
HM 3096
HM 3096
HM 3096
HM 3096
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
HMV 96
HMV 96
HMV 96
HMV 96
HMV 96
23096 CAK/W33
23096 CAK/W33
23096 CAK/W33
23096 CAK/W33
23096 CAK/W33
620
620
620
620
620
335
335
335
335
335
75
75
75
75
75
95
95
95
95
95
12
12
15
15
-
6.5
6.5
14
14
-
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
M8
M8
-
G 1/4
G 1/4
-
135
135
135
135
135
OH 3196 H
OH 3196 HB
OH 3196
OH 3196 B
H 3196
HM 3196
HM 3196
HM 3196
HM 3196
HM 3196
MS 3196
MS 3196
MS 3196
MS 3196
MS 3196
HMV 96
HMV 96
HMV 96
HMV 96
HMV 96
23196 CAK/W33
23196 CAK/W33
23196 CAK/W33
23196 CAK/W33
23196 CAK/W33
620
620
620
620
620
397
397
397
397
397
75
75
75
75
75
95
95
95
95
95
12
12
15
15
-
6.5
6.5
17
17
-
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
M8
M8
-
G 1/4
G 1/4
-
153
153
153
153
153
OH 3296 H
OH 3296 HB
OH 3296
OH 3296 B
H 3296
HM 3196
HM 3196
HM 3196
HM 3196
HM 3196
MS 3196
MS 3196
MS 3196
MS 3196
MS 3196
HMV 96
HMV 96
HMV 96
HMV 96
HMV 96
23296 CAK/W33
23296 CAK/W33
23296 CAK/W33
23296 CAK/W33
23296 CAK/W33
580
580
580
580
580
208
208
208
208
208
68
68
68
68
68
85
85
85
85
85
12
12
15
15
-
6.5
6.5
10
10
-
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
M8
M8
-
G 1/4
G 1/4
-
74.3
74.3
74.3
74.3
74.3
OH 39/500 H
OH 39/500 HB
OH 39/500
OH 39/500B
H 39/500
HM 30/500
HM 30/500
HM 30/500
HM 30/500
HM 30/500
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
HMV 100
HMV 100
HMV 100
HMV 100
HMV 100
239/500 CAK/W33
239/500 CAK/W33
239/500 CAK/W33
239/500 CAK/W33
239/500 CAK/W33
580
580
580
580
580
247
247
247
247
247
68
68
68
68
68
85
85
85
85
85
12
12
15
15
-
6.5
6.5
11
11
-
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
M8
M8
-
G 1/4
G 1/4
-
82
82
82
82
82
OH 30/500 H
OH 30/500 HB
OH 30/500
OH 30/500 B
H 30/500
HM 30/500
HM 30/500
HM 30/500
HM 30/500
HM 30/500
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
HMV 100
HMV 100
HMV 100
HMV 100
HMV 100
230/500 CAK/W33
230/500 CAK/W33
230/500 CAK/W33
230/500 CAK/W33
230/500 CAK/W33
630
630
630
630
630
356
356
356
356
356
80
80
80
80
80
100
100
100
100
100
12
12
15
15
-
6.5
6.5
15
15
-
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
M8
M8
-
G 1/4
G 1/4
-
145
145
145
145
145
OH 31/500 H
OH 31/500 HB
OH 31/500
OH 31/500 B
H 31/500
HM 31/500
HM 31/500
HM 31/500
HM 31/500
HM 31/500
MS 31/500
MS 31/500
MS 31/500
MS 31/500
MS 31/500
HMV 100
HMV 100
HMV 100
HMV 100
HMV 100
231/500 CAK/W33
231/500 CAK/W33
231/500 CAK/W33
231/500 CAK/W33
231/500 CAK/W33
630
630
630
630
630
428
428
428
428
428
80
80
80
80
80
100
100
100
100
100
12
12
15
15
-
6
6
18
18
-
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
M8
M8
-
G 1/4
G 1/4
-
170
170
170
170
170
OH 32/500 H
OH 32/500 HB
OH 32/500
OH 32/500 B
H 32/500
HM 31/500
HM 31/500
HM 31/500
HM 31/500
HM 31/500
MS 31/500
MS 31/500
MS 31/500
MS 31/500
MS 31/500
HMV 100
HMV 100
HMV 100
HMV 100
HMV 100
232/500 CAK/W33
232/500 CAK/W33
232/500 CAK/W33
232/500 CAK/W33
232/500 CAK/W33
534
Designations
Adapter sleeve
with lock nut
and locking
device
Adapter sleeves
d1 500 530 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
500 530
530 560
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
630
630
630
630
630
216
216
216
216
216
68
68
68
68
68
90
90
90
90
90
12
12
15
15
-
6
6
11
11
-
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
M8
M8
-
G 1/4
G 1/4
-
87.9
87.9
87.9
87.9
87.9
OH 39/530 H
OH 39/530 HB
OH 39/530
OH 39/530 B
H 39/530
HM 30/530
HM 30/530
HM 30/530
HM 30/530
HM 30/530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
HMV 106
HMV 106
HMV 106
HMV 106
HMV 106
239/530 CAK/W33
239/530 CAK/W33
239/530 CAK/W33
239/530 CAK/W33
239/530 CAK/W33
630
630
630
630
630
265
265
265
265
265
68
68
68
68
68
90
90
90
90
90
12
12
15
15
-
6
6
13
13
-
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
M8
M8
-
G 1/4
G 1/4
-
105
105
105
105
105
OH 30/530 H
OH 30/530 HB
OH 30/530
OH 30/530 B
H 30/530
HM 30/530
HM 30/530
HM 30/530
HM 30/530
HM 30/530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
HMV 106
HMV 106
HMV 106
HMV 106
HMV 106
230/530 CAK/W33
230/530 CAK/W33
230/530 CAK/W33
230/530 CAK/W33
230/530 CAK/W33
670
670
670
670
670
364
364
364
364
364
80
80
80
80
80
105
105
105
105
105
12
12
15
15
-
6
6
15
15
-
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
M8
M8
-
G 1/4
G 1/4
-
161
161
161
161
161
OH 31/530 H
OH 31/530 HB
OH 31/530
OH 31/530 B
H 31/530
HM 31/530
HM 31/530
HM 31/530
HM 31/530
HM 31/530
MS 31/530
MS 31/530
MS 31/530
MS 31/530
MS 31/530
HMV 106
HMV 106
HMV 106
HMV 106
HMV 106
231/530 CAK/W33
231/530 CAK/W33
231/530 CAK/W33
231/530 CAK/W33
231/530 CAK/W33
670
670
670
670
670
447
447
447
447
447
80
80
80
80
80
105
105
105
105
105
12
12
15
15
-
6
6
19
19
-
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
M8
M8
-
G 1/4
G 1/4
-
192
192
192
192
192
OH 32/530 H
OH 32/530 HB
OH 32/530
OH 32/530 B
H 32/530
HM 31/530
HM 31/530
HM 31/530
HM 31/530
HM 31/530
MS 31/530
MS 31/530
MS 31/530
MS 31/530
MS 31/530
HMV 106
HMV 106
HMV 106
HMV 106
HMV 106
232/530 CAK/W33
232/530 CAK/W33
232/530 CAK/W33
232/530 CAK/W33
232/530 CAK/W33
650
650
650
650
650
227
227
227
227
227
75
75
75
75
75
97
97
97
97
97
12
12
15
15
-
6
6
11
11
-
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
M8
M8
-
G 1/4
G 1/4
-
95
95
95
95
95
OH 39/560 H
OH 39/560 HB
OH 39/560
OH 39/560 B
H 39/560
HM 30/560
HM 30/560
HM 30/560
HM 30/560
HM 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
HMV 112
HMV 112
HMV 112
HMV 112
HMV 112
239/560 CAK/W33
239/560 CAK/W33
239/560 CAK/W33
239/560 CAK/W33
239/560 CAK/W33
650
650
650
650
650
282
282
282
282
282
75
75
75
75
75
97
97
97
97
97
12
12
15
15
-
6
6
13
13
-
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
M8
M8
-
G 1/4
G 1/4
-
112
112
112
112
112
OH 30/560 H
OH 30/560 HB
OH 30/560
OH 30/560 B
H3 0/560
HM 30/560
HM 30/560
HM 30/560
HM 30/560
HM 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
HMV 112
HMV 112
HMV 112
HMV 112
HMV 112
230/560 CAK/W33
230/560 CAK/W33
230/560 CAK/W33
230/560 CAK/W33
230/560 CAK/W33
710
710
710
710
710
377
377
377
377
377
85
85
85
85
85
110
110
110
110
110
12
12
15
15
-
6
6
16
16
-
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
M8
M8
-
G 1/4
G 1/4
-
185
185
185
185
185
OH 31/560 H
OH 31/560 HB
OH 31/560
OH 31/560 B
H 31/560
HM 31/560
HM 31/560
HM 31/560
HM 31/560
HM 31/560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
HMV 112
HMV 112
HMV 112
HMV 112
HMV 112
231/560 CAK/W33
231/560 CAK/W33
231/560 CAK/W33
231/560 CAK/W33
231/560 CAK/W33
710
710
710
710
710
462
462
462
462
462
85
85
85
85
85
110
110
110
110
110
12
12
15
15
-
6
6
19
19
-
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
M8
M8
-
G 1/4
G 1/4
-
219
219
219
219
219
OH 32/560 H
OH 32/560 HB
OH 32/560
OH 32/560 B
H 32/560
HM 31/560
HM 31/560
HM 31/560
HM 31/560
HM 31/560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
HMV 112
HMV 112
HMV 112
HMV 112
HMV 112
232/560 CAK/W33
232/560 CAK/W33
232/560 CAK/W33
232/560 CAK/W33
232/560 CAK/W33
535

Adapter sleeves
d1 560 600 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
G1
mm
560 600
600 630
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
700
700
700
700
700
239
239
239
239
239
75
75
75
75
75
97
97
97
97
97
13
13
15
15
-
8
8
16
16
-
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
G 1/8
G 1/8
G 1/4
G 1/4
-
127
127
127
127
127
OH 39/600 H
OH 39/600 HB
OH 39/600
OH 39/600 B
H 39/600
HM 30/600
HM 30/600
HM 30/600
HM 30/600
HM 30/600
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
HMV 120
HMV 120
HMV 120
HMV 120
HMV 120
239/600 CAK/W33
239/600 CAK/W33
239/600 CAK/W33
239/600 CAK/W33
239/600 CAK/W33
700
700
700
700
700
289
289
289
289
289
75
75
75
75
75
97
97
97
97
97
13
13
15
15
-
8
8
18
18
-
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
G 1/8
G 1/8
G 1/4
G 1/4
-
147
147
147
147
147
OH 30/600 H
OH 30/600 HB
OH 30/600
OH 30/600 B
H 30/600
HM 30/600
HM 30/600
HM 30/600
HM 30/600
HM 30/600
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
HMV 120
HMV 120
HMV 120
HMV 120
HMV 120
230/600 CAK/W33
230/600 CAK/W33
230/600 CAK/W33
230/600 CAK/W33
230/600 CAK/W33
750
750
750
750
750
399
399
399
399
399
85
85
85
85
85
110
110
110
110
110
13
13
15
15
-
8
8
22
22
-
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
G 1/8
G 1/8
G 1/4
G 1/4
-
234
234
234
234
234
OH 31/600 H
OH 31/600 HB
OH 31/600
OH 31/600 B
H 31/600
HM 31/600
HM 31/600
HM 31/600
HM 31/600
HM 31/600
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
HMV 120
HMV 120
HMV 120
HMV 120
HMV 120
231/600 CAK/W33
231/600 CAK/W33
231/600 CAK/W33
231/600 CAK/W33
231/600 CAK/W33
750
750
750
750
750
487
487
487
487
487
85
85
85
85
85
110
110
110
110
110
13
13
15
15
-
8
8
25
25
-
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
G 1/8
G 1/8
G 1/4
G 1/4
-
278
278
278
278
278
OH 32/600 H
OH 32/600 HB
OH 32/600
OH 32/600 B
H 32/600
HM 31/600
HM 31/600
HM 31/600
HM 31/600
HM 31/600
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
MS 31/600-560
HMV 120
HMV 120
HMV 120
HMV 120
HMV 120
232/600 CAK/W33
232/600 CAK/W33
232/600 CAK/W33
232/600 CAK/W33
232/600 CAK/W33
730
730
730
730
730
254
254
254
254
254
75
75
75
75
75
97
97
97
97
97
12
12
15
15
-
6
6
12
12
-
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
M8
M8
-
G 1/4
G 1/4
-
124
124
124
124
124
OH 39/630 H
OH 39/630 HB
OH 39/630
OH 39/630 B
H 39/630
HM 30/630
HM 30/630
HM 30/630
HM 30/630
HM 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
HMV 126
HMV 126
HMV 126
HMV 126
HMV 126
239/630 CAK/W33
239/630 CAK/W33
239/630 CAK/W33
239/630 CAK/W33
239/630 CAK/W33
730
730
730
730
730
301
301
301
301
301
75
75
75
75
75
97
97
97
97
97
12
12
15
15
-
6
6
13
13
-
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
M8
M8
-
G 1/4
G 1/4
-
138
138
138
138
138
OH 30/630 H
OH 30/630 HB
OH 30/630
OH 30/630 B
H 30/630
HM 30/630
HM 30/630
HM 30/630
HM 30/630
HM 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
HMV 126
HMV 126
HMV 126
HMV 126
HMV 126
230/630 CAK/W33
230/630 CAK/W33
230/630 CAK/W33
230/630 CAK/W33
230/630 CAK/W33
800
800
800
800
800
424
424
424
424
424
95
95
95
95
95
120
120
120
120
120
12
12
15
15
-
6
6
17
17
-
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
M8
M8
-
G 1/4
G 1/4
-
254
254
254
254
254
OH 31/630 H
OH 31/630 HB
OH 31/630
OH 31/630 B
H 31/630
HM 31/630
HM 31/630
HM 31/630
HM 31/630
HM 31/630
MS 31/630
MS 31/630
MS 31/630
MS 31/630
MS 31/630
HMV 126
HMV 126
HMV 126
HMV 126
HMV 126
231/630 CAK/W33
231/630 CAK/W33
231/630 CAK/W33
231/630 CAK/W33
231/630 CAK/W33
800
800
800
800
800
521
521
521
521
521
95
95
95
95
95
120
120
120
120
120
12
12
15
15
-
6
6
21
21
-
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
M8
M8
-
G 1/4
G 1/4
-
300
300
300
300
300
OH 32/630 H
OH 32/630 HB
OH 32/630
OH 32/630 B
H 32/630
HM 31/630
HM 31/630
HM 31/630
HM 31/630
HM 31/630
MS 31/630
MS 31/630
MS 31/630
MS 31/630
MS 31/630
HMV 126
HMV 126
HMV 126
HMV 126
HMV 126
232/630 CAK/W33
232/630 CAK/W33
232/630 CAK/W33
232/630 CAK/W33
232/630 CAK/W33
536
Designations
Adapter sleeve
with lock nut
and locking
device
Adapter sleeves
d1 630 670 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
mm
630
670
670
710
G1
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
780
780
780
780
780
264
264
264
264
264
80
80
80
80
80
102
102
102
102
102
13
13
15
15
-
8
8
17
17
-
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
G 1/8
G 1/8
G 1/4
G 1/4
-
162
162
162
162
162
OH 39/670 H
OH 39/670 HB
OH 39/670
OH 39/670 B
H 39/670
HM 30/670
HM 30/670
HM 30/670
HM 30/670
HM 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
HMV 134
HMV 134
HMV 134
HMV 134
HMV 134
239/670 CAK/W33
239/670 CAK/W33
239/670 CAK/W33
239/670 CAK/W33
239/670 CAK/W33
780
780
780
780
780
324
324
324
324
324
80
80
80
80
80
102
102
102
102
102
13
13
15
15
-
8
8
19
19
-
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
G 1/8
G 1/8
G 1/4
G 1/4
-
190
190
190
190
190
OH 30/670 H
OH 30/670 HB
OH 30/670
OH 30/670 B
H 30/670
HM 30/670
HM 30/670
HM 30/670
HM 30/670
HM 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
HMV 134
HMV 134
HMV 134
HMV 134
HMV 134
230/670 CAK/W33
230/670 CAK/W33
230/670 CAK/W33
230/670 CAK/W33
230/670 CAK/W33
850
850
850
850
850
456
456
456
456
456
106
106
106
106
106
131
131
131
131
131
13
13
15
15
-
8
8
23
23
-
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
G 1/8
G 1/8
G 1/4
G 1/4
-
340
340
340
340
340
OH 31/670 H
OH 31/670 HB
OH 31/670
OH 31/670 B
H 31/670
HM 31/670
HM 31/670
HM 31/670
HM 31/670
HM 31/670
MS 31/670
MS 31/670
MS 31/670
MS 31/670
MS 31/670
HMV 134
HMV 134
HMV 134
HMV 134
HMV 134
231/670 CAK/W33
231/670 CAK/W33
231/670 CAK/W33
231/670 CAK/W33
231/670 CAK/W33
850
850
850
850
850
558
558
558
558
558
106
106
106
106
106
131
131
131
131
131
13
13
15
15
-
8
8
27
27
-
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
G 1/8
G 1/8
G 1/4
G 1/4
-
401
401
401
401
401
OH 32/670 H
OH 32/670 HB
OH 32/670
OH 32/670 B
H 32/670
HM 31/670
HM 31/670
HM 31/670
HM 31/670
HM 31/670
MS 31/670
MS 31/670
MS 31/670
MS 31/670
MS 31/670
HMV 134
HMV 134
HMV 134
HMV 134
HMV 134
232/670 CAK/W33
232/670 CAK/W33
232/670 CAK/W33
232/670 CAK/W33
232/670 CAK/W33
830
830
830
830
830
286
286
286
286
286
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
8
8
18
18
-
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
G 1/8
G 1/8
G 1/4
G 1/4
-
183
183
183
183
183
OH 39/710 H
OH 39/710 HB
OH 39/710
OH 39/710 B
H 39/710
HM 30/710
HM 30/710
HM 30/710
HM 30/710
HM 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
HMV 142
HMV 142
HMV 142
HMV 142
HMV 142
239/710 CAK/W33
239/710 CAK/W33
239/710 CAK/W33
239/710 CAK/W33
239/710 CAK/W33
830
830
830
830
830
342
342
342
342
342
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
8
8
19
19
-
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
G 1/8
G 1/8
G 1/4
G 1/4
-
228
228
228
228
228
OH 30/710 H
OH 30/710 HB
OH 30/710
OH 30/710 B
H 30/710
HM 30/710
HM 30/710
HM 30/710
HM 30/710
HM 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
HMV 142
HMV 142
HMV 142
HMV 142
HMV 142
230/710 CAK/W33
230/710 CAK/W33
230/710 CAK/W33
230/710 CAK/W33
230/710 CAK/W33
900
900
900
900
900
467
467
467
467
467
106
106
106
106
106
135
135
135
135
135
13
13
15
15
-
8
8
24
24
-
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
G 1/8
G 1/8
G 1/4
G 1/4
-
392
392
392
392
392
OH 31/710 H
OH 31/710 HB
OH 31/710
OH 31/710 B
H 31/710
HM 31/710
HM 31/710
HM 31/710
HM 31/710
HM 31/710
MS 31/710
MS 31/710
MS 31/710
MS 31/710
MS 31/710
HMV 142
HMV 142
HMV 142
HMV 142
HMV 142
231/710 CAK/W33
231/710 CAK/W33
231/710 CAK/W33
231/710 CAK/W33
231/710 CAK/W33
900
900
900
900
900
572
572
572
572
572
106
106
106
106
106
135
135
135
135
135
13
13
15
15
-
8
8
28
28
-
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
G 1/8
G 1/8
G 1/4
G 1/4
-
459
459
459
459
459
OH 32/710 H
OH 32/710 HB
OH 32/710
OH 32/710 B
H 32/710
HM 31/710
HM 31/710
HM 31/710
HM 31/710
HM 31/710
MS 31/710
MS 31/710
MS 31/710
MS 31/710
MS 31/710
HMV 142
HMV 142
HMV 142
HMV 142
HMV 142
232/710 CAK/W33
232/710 CAK/W33
232/710 CAK/W33
232/710 CAK/W33
232/710 CAK/W33
537

Adapter sleeves
d1 710 750 mm
Type OH . . H
Type OH . . HB
Size 60 and over
Type H
MS locking device
Dimensions
d1
750
750
800
d3
B1
B2
B3
B4 A
G1
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
870
870
870
870
870
291
291
291
291
291
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
8
8
18
18
-
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
G 1/8
G 1/8
G 1/4
G 1/4
-
211
211
211
211
211
OH 39/750 H
OH 39/750 HB
OH 39/750
OH 39/750 B
H 39/750
HM 30/750
HM 30/750
HM 30/750
HM 30/750
HM 30/750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
HMV 150
HMV 150
HMV 150
HMV 150
HMV 150
239/750 CAK/W33
239/750 CAK/W33
239/750 CAK/W33
239/750 CAK/W33
239/750 CAK/W33
870
870
870
870
870
356
356
356
356
356
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
8
8
20
20
-
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
G 1/8
G 1/8
G 1/4
G 1/4
-
246
246
246
246
246
OH 30/750 H
OH 30/750 HB
OH 30/750
OH 30/750 B
H 30/750
HM 30/750
HM 30/750
HM 30/750
HM 30/750
HM 30/750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
HMV 150
HMV 150
HMV 150
HMV 150
HMV 150
230/750 CAK/W33
230/750 CAK/W33
230/750 CAK/W33
230/750 CAK/W33
230/750 CAK/W33
950
950
950
950
950
493
493
493
493
493
112
112
112
112
112
141
141
141
141
141
13
13
15
15
-
8
8
24
24
-
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
G 1/8
G 1/8
G 1/4
G 1/4
-
451
451
451
451
451
OH 31/750 H
OH 31/750 HB
OH 31/750
OH 31/750 B
H 31/750
HM 31/750
HM 31/750
HM 31/750
HM 31/750
HM 31/750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
HMV 150
HMV 150
HMV 150
HMV 150
HMV 150
231/750 CAK/W33
231/750 CAK/W33
231/750 CAK/W33
231/750 CAK/W33
231/750 CAK/W33
950
950
950
950
950
603
603
603
603
603
112
112
112
112
112
141
141
141
141
141
13
13
15
15
-
8
8
29
29
-
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
G 1/8
G 1/8
G 1/4
G 1/4
-
526
526
526
526
526
OH 32/750 H
OH 32/750 HB
OH 32/750
OH 32/750 B
H 32/750
HM 31/750
HM 31/750
HM 31/750
HM 31/750
HM 31/750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
HMV 150
HMV 150
HMV 150
HMV 150
HMV 150
232/750 CAK/W33
232/750 CAK/W33
232/750 CAK/W33
232/750 CAK/W33
232/750 CAK/W33
920
920
920
920
920
303
303
303
303
303
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
10
10
23
23
-
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
G 1/8
G 1/8
G 1/4
G 1/4
-
259
259
259
259
259
OH 39/800 H
OH 39/800 HB
OH 39/800
OH 39/800 B
H 39/800
HM 30/800
HM 30/800
HM 30/800
HM 30/800
HM 30/800
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
HMV 160
HMV 160
HMV 160
HMV 160
HMV 160
239/800 CAK/W33
239/800 CAK/W33
239/800 CAK/W33
239/800 CAK/W33
239/800 CAK/W33
920
920
920
920
920
366
366
366
366
366
90
90
90
90
90
112
112
112
112
112
13
13
15
15
-
10
10
25
25
-
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
G 1/8
G 1/8
G 1/4
G 1/4
-
302
302
302
302
302
OH 30/800 H
OH 30/800 HB
OH 30/800
OH 30/800 B
H30/800
HM 30/800
HM 30/800
HM 30/800
HM 30/800
HM 30/800
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
HMV 160
HMV 160
HMV 160
HMV 160
HMV 160
230/800 CAK/W33
230/800 CAK/W33
230/800 CAK/W33
230/800 CAK/W33
230/800 CAK/W33
1 000
1 000
1 000
1 000
1 000
505
505
505
505
505
112
112
112
112
112
141
141
141
141
141
13
13
15
15
-
10
10
30
30
-
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
G 1/8
G 1/8
G 1/4
G 1/4
-
535
535
535
535
535
OH 31/800 H
OH 31/800 HB
OH 31/800
OH 31/800 B
H 31/800
HM 31/800
HM 31/800
HM 31/800
HM 31/800
HM 31/800
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
HMV 160
HMV 160
HMV 160
HMV 160
HMV 160
231/800 CAK/W33
231/800 CAK/W33
231/800 CAK/W33
231/800 CAK/W33
231/800 CAK/W33
1 000
1 000
1 000
1 000
1 000
618
618
618
618
618
112
112
112
112
112
141
141
141
141
141
13
13
15
15
-
10
10
34
34
-
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
G 1/8
G 1/8
G 1/4
G 1/4
-
629
629
629
629
629
OH 32/800 H
OH 32/800 HB
OH 32/800
OH 32/800 B
H 32/800
HM 31/800
HM 31/800
HM 31/800
HM 31/800
HM 31/800
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
MS 31/800-750
HMV 160
HMV 160
HMV 160
HMV 160
HMV 160
232/800 CAK/W33
232/800 CAK/W33
232/800 CAK/W33
232/800 CAK/W33
232/800 CAK/W33
538
Type OH . . B
Size 60 and over
Mass
mm
710
Type OH
Adapter sleeves
d1 800 850 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
mm
800
850
850
900
G1
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
980
980
980
980
980
308
308
308
308
308
90
90
90
90
90
115
115
115
115
115
13
13
15
15
-
10
10
23
23
-
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
G 1/8
G 1/8
G 1/4
G 1/4
-
288
288
288
288
288
OH 39/850 H
OH 39/850 HB
OH 39/850
OH 39/850 B
H 39/850
HM 30/850
HM 30/850
HM 30/850
HM 30/850
HM 30/850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
HMV 170
HMV 170
HMV 170
HMV 170
HMV 170
239/850 CAK/W33
239/850 CAK/W33
239/850 CAK/W33
239/850 CAK/W33
239/850 CAK/W33
980
980
980
980
980
380
380
380
380
380
90
90
90
90
90
115
115
115
115
115
13
13
15
15
-
10
10
25
25
-
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
G 1/8
G 1/8
G 1/4
G 1/4
-
341
341
341
341
341
OH 30/850 H
OH 30/850 HB
OH 30/850
OH 30/850 B
H 30/850
HM 30/850
HM 30/850
HM 30/850
HM 30/850
HM 30/850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
HMV 170
HMV 170
HMV 170
HMV 170
HMV 170
230/850 CAK/W33
230/850 CAK/W33
230/850 CAK/W33
230/850 CAK/W33
230/850 CAK/W33
1 060
1 060
1 060
1 060
1 060
536
536
536
536
536
118
118
118
118
118
147
147
147
147
147
13
13
15
15
-
10
10
31
31
-
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
G 1/8
G 1/8
G 1/4
G 1/4
-
616
616
616
616
616
OH 31/850 H
OH 31/850 HB
OH 31/850
OH 31/850 B
H 31/850
HM 31/850
HM 31/850
HM 31/850
HM 31/850
HM 31/850
MS 31/850
MS 31/850
MS 31/850
MS 31/850
MS 31/850
HMV 170
HMV 170
HMV 170
HMV 170
HMV 170
231/850 CAK/W33
231/850 CAK/W33
231/850 CAK/W33
231/850 CAK/W33
231/850 CAK/W33
1 060
1 060
1 060
1 060
1 060
651
651
651
651
651
118
118
118
118
118
147
147
147
147
147
13
13
15
15
-
10
10
35
35
-
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
G 1/8
G 1/8
G 1/4
G 1/4
-
722
722
722
722
722
OH 32/850 H
OH 32/850 HB
OH 32/850
OH 32/850 B
H 32/850
HM 31/850
HM 31/850
HM 31/850
HM 31/850
HM 31/850
MS 31/850
MS 31/850
MS 31/850
MS 31/850
MS 31/850
HMV 170
HMV 170
HMV 170
HMV 170
HMV 170
232/850 CAK/W33
232/850 CAK/W33
232/850 CAK/W33
232/850 CAK/W33
232/850 CAK/W33
1 030
1 030
1 030
1 030
1 030
326
326
326
326
326
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
23
23
-
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
G 1/8
G 1/8
G 1/4
G 1/4
-
330
330
330
330
330
OH 39/900 H
OH 39/900 HB
OH 39/900
OH 39/900 B
H 39/900
HM 30/900
HM 30/900
HM 30/900
HM 30/900
HM 30/900
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
HMV 180
HMV 180
HMV 180
HMV 180
HMV 180
239/900 CAK/W33
239/900 CAK/W33
239/900 CAK/W33
239/900 CAK/W33
239/900 CAK/W33
1 030
1 030
1 030
1 030
1 030
400
400
400
400
400
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
25
25
-
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
G 1/8
G 1/8
G 1/4
G 1/4
-
387
387
387
387
387
OH 30/900 H
OH 30/900 HB
OH 30/900
OH 30/900 B
H 30/900
HM 30/900
HM 30/900
HM 30/900
HM 30/900
HM 30/900
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
HMV 180
HMV 180
HMV 180
HMV 180
HMV 180
230/900 CAK/W33
230/900 CAK/W33
230/900 CAK/W33
230/900 CAK/W33
230/900 CAK/W33
1 120
1 120
1 120
1 120
1 120
557
557
557
557
557
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
31
31
-
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
G 1/8
G 1/8
G 1/4
G 1/4
-
677
677
677
677
677
OH 31/900 H
OH 31/900 HB
OH 31/900
OH 31/900 B
H 31/900
HM 31/900
HM 31/900
HM 31/900
HM 31/900
HM 31/900
MS 31/900
MS 31/900
MS 31/900
MS 31/900
MS 31/900
HMV 180
HMV 180
HMV 180
HMV 180
HMV 180
231/900 CAK/W33
231/900 CAK/W33
231/900 CAK/W33
231/900 CAK/W33
231/900 CAK/W33
1 120
1 120
1 120
1 120
1 120
660
660
660
660
660
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
35
35
-
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
G 1/8
G 1/8
G 1/4
G 1/4
-
776
776
776
776
776
OH 32/900 H
OH 32/900 HB
OH 32/900
OH 32/900 B
H 32/900
HM 31/900
HM 31/900
HM 31/900
HM 31/900
HM 31/900
MS 31/900
MS 31/900
MS 31/900
MS 31/900
MS 31/900
HMV 180
HMV 180
HMV 180
HMV 180
HMV 180
232/900 CAK/W33
232/900 CAK/W33
232/900 CAK/W33
232/900 CAK/W33
232/900 CAK/W33
539

Adapter sleeves
d1 900 950 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
mm
900
950
950
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
1 080
1 080
1 080
1 080
1 080
344
344
344
344
344
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
23
23
-
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
G 1/8
G 1/8
G 1/4
G 1/4
-
362
362
362
362
362
OH 39/950 H
OH 39/950 HB
OH 39/950
OH 39/950 B
H 39/950
HM 30/950
HM 30/950
HM 30/950
HM 30/950
HM 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
HMV 190
HMV 190
HMV 190
HMV 190
HMV 190
239/950 CAK/W33
239/950 CAK/W33
239/950 CAK/W33
239/950 CAK/W33
239/950 CAK/W33
1 080
1 080
1 080
1 080
1 080
420
420
420
420
420
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
25
25
-
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
G 1/8
G 1/8
G 1/4
G 1/4
-
424
424
424
424
424
OH 30/950 H
OH 30/950 HB
OH 30/950
OH 30/950 B
H 30/950
HM 30/950
HM 30/950
HM 30/950
HM 30/950
HM 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
HMV 190
HMV 190
HMV 190
HMV 190
HMV 190
230/950 CAK/W33
230/950 CAK/W33
230/950 CAK/W33
230/950 CAK/W33
230/950 CAK/W33
1 170
1 170
1 170
1 170
1 170
583
583
583
583
583
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
31
31
-
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
G 1/8
G 1/8
G 1/4
G 1/4
-
738
738
738
738
738
OH 31/950 H
OH 31/950 HB
OH 31/950
OH 31/950 B
H 31/950
HM 31/950
HM 31/950
HM 31/950
HM 31/950
HM 31/950
MS 31/950
MS 31/950
MS 31/950
MS 31/950
MS 31/950
HMV 190
HMV 190
HMV 190
HMV 190
HMV 190
231/950 CAK/W33
231/950 CAK/W33
231/950 CAK/W33
231/950 CAK/W33
231/950 CAK/W33
1 170
1 170
1 170
1 170
1 170
675
675
675
675
675
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
35
35
-
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
G 1/8
G 1/8
G 1/4
G 1/4
-
834
834
834
834
834
OH 32/950 H
OH 32/950 HB
OH 32/950
OH 32/950 B
H 32/950
HM 31/950
HM 31/950
HM 31/950
HM 31/990
HM 31/950
MS 31/950
MS 31/950
MS 31/950
MS 31/950
MS 31/950
HMV 190
HMV 190
HMV 190
HMV 190
HMV 190
232/950 CAK/W33
232/950 CAK/W33
232/950 CAK/W33
232/950 CAK/W33
232/950 CAK/W33
1 000 1 140
1 140
1 140
1 140
1 140
358
358
358
358
358
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
23
23
-
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
G 1/8
G 1/8
G 1/4
G 1/4
-
407
407
407
407
407
OH 39/1000 H
OH 39/1000 HB
OH 39/1000
OH 39/1000 B
H 39/1000
HM 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
HMV 200
HMV 200
HMV 200
HMV 200
HMV 200
239/1000 CAK/W33
239/1000 CAK/W33
239/1000 CAK/W33
239/1000 CAK/W33
239/1000 CAK/W33
1 140
1 140
1 140
1 140
1 140
430
430
430
430
430
100
100
100
100
100
125
125
125
125
125
13
13
15
15
-
10
10
25
25
-
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
G 1/8
G 1/8
G 1/4
G 1/4
-
470
470
470
470
470
OH 30/1000 H
OH 30/1000 HB
OH 30/1000
OH 30/1000 B
H 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
HMV 200
HMV 200
HMV 200
HMV 200
HMV 200
230/1000 CAK/W33
230/1000 CAK/W33
230/1000 CAK/W33
230/1000 CAK/W33
230/1000 CAK/W33
1 240
1 240
1 240
1 240
1 240
609
609
609
609
609
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
31
31
-
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
G 1/8
G 1/8
G 1/4
G 1/4
-
842
842
842
842
842
OH 31/1000 H
OH 31/1000 HB
OH 31/1000
OH 31/1000 B
H 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
HMV 200
HMV 200
HMV 200
HMV 200
HMV 200
231/1000 CAK/W33
231/1000 CAK/W33
231/1000 CAK/W33
231/1000 CAK/W33
231/1000 CAK/W33
1 240
1 240
1 240
1 240
1 240
707
707
707
707
707
125
125
125
125
125
154
154
154
154
154
13
13
15
15
-
10
10
35
35
-
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
G 1/8
G 1/8
G 1/4
G 1/4
-
952
952
952
952
952
OH 32/1000 H
OH 32/1000 HB
OH 32/1000
OH 32/1000 B
H 32/1000
HM 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
HMV 200
HMV 200
HMV 200
HMV 200
HMV 200
232/1000 CAK/W33
232/1000 CAK/W33
232/1000 CAK/W33
232/1000 CAK/W33
232/1000 CAK/W33
540
G1
Designations
Adapter sleeve
with lock nut
and locking
device
Adapter sleeves
d1 1000 mm
Type H
MS locking device
Type OH . . H
Type OH
Type OH . . HB
Size 60 and over
Type OH . . B
Size 60 and over
Dimensions
d1
Mass
d3
B1
B2
B3
B4 A
mm
G1
Designations
Adapter sleeve
with lock nut
and locking
device
in
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
1 000 1 060 1 200

1 200
1 200
1 200
1 200
372
372
372
372
372
100
100
100
100
100
125
125
125
125
125
15
15
15
15
-
12
12
23
23
-
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
G 1/4
G 1/4
G 1/4
G 1/4
-
490
490
490
490
490
OH 39/1060 H
OH 39/1060 HB
OH 39/1060
OH 39/1060 B
H 39/1060
HM 30/1060
HM 30/1060
HM 30/1060
HM 30/1060
HM 30/1060
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
HMV 212
HMV 212
HMV 212
HMV 212
HMV 212
239/1060 CAK/W33
239/1060 CAK/W33
239/1060 CAK/W33
239/1060 CAK/W33
239/1060 CAK/W33
1 200
1 200
1 200
1 200
1 200
447
447
447
447
447
100
100
100
100
100
125
125
125
125
125
15
15
15
15
-
12
12
25
25
-
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
G 1/4
G 1/4
G 1/4
G 1/4
-
571
571
571
571
571
OH 30/1060 H
OH 30/1060 HB
OH 30/1060
OH 30/1060 B
H 30/1060
HM 30/1060
HM 30/1060
HM 30/1060
HM 30/1060
HM 30/1060
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
HMV 212
HMV 212
HMV 212
HMV 212
HMV 212
230/1060 CAK/W33
230/1060 CAK/W33
230/1060 CAK/W33
230/1060 CAK/W33
230/1060 CAK/W33
1 300
1 300
1 300
1 300
1 300
622
622
622
622
622
125
125
125
125
125
154
154
154
154
154
15
15
15
15
-
12
12
31
31
-
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
Tr l060x8
G 1/4
G 1/4
G 1/4
G 1/4
-
984
984
984
984
984
OH 31/1060 H
OH 31/1060 HB
OH 31/1060
OH 31/1060 B
H 31/1060
HM 31/1060
HM 31/1060
HM 31/1060
HM 31/1060
HM 31/1060
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
MS 31/1000
HMV 212
HMV 212
HMV 212
HMV 212
HMV 212
231/1060 CAK/W33
231/1060 CAK/W33
231/1060 CAK/W33
231/1060 CAK/W33
231/1060 CAK/W33
541

Adapter sleeves
for shafts with inch dimensions
d1 34 11116 in
Type HA, HE, HS
Dimensions
d1
Mass
d3
B1
B2 G
in
Designations
Adapter sleeve
with lock nut
and locking
device
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
25
38
38
38
26
29
35
8
8
8
M 25x1.5
M 25x1.5
M 25x1.5
0.07
0.08
0.09
HE 205
HE 305
HE 2305
KM 5
KM 5
KM 5
MB 5
MB 5
MB 5
1205 EK
2205 EK, 1305 EK
2305 K
30
45
45
27
31
8
8
M 30x1.5
M 30x1.5
0.11
0.12
HS 206
HS 306
KM 6
KM 6
MB 6
MB 6
1206 EK
2206 EK, 1306 EK
16
30
45
45
45
27
31
38
8
8
8
M 30x1.5
M 30x1.5
M 30x1.5
0.1
0.12
0.13
HA 206
HA 306
HA 2306
KM 6
KM 6
KM 6
MB 6
MB 6
MB 6
1206 EK
2206 EK, 1306 EK
2306 K
30
45
45
45
27
31
38
8
8
8
M 30x1.5
M 30x1.5
M 30x1.5
0.08
0.1
0.11
HE 206
HE 306
HE 2306
KM 6
KM 6
KM 6
MB 6
MB 6
MB 6
1206 EK
2206 EK, 1306 EK
2306 K
118
35
52
52
29
35
9
9
M 35x1.5
M 35x1.5
0.14
0.16
HS 207
HS 307
KM 7
KM 7
MB 7
MB 7
1207 EK
2207 EK, 1307 EK, 22207 EK
1316
35
52
52
52
29
35
43
9
9
9
M 35x1.5
M 35x1.5
M 35x1.5
0.12
0.14
0.16
HA 207
HA 307
HA 2307
KM 7
KM 7
KM 7
MB 7
MB 7
MB 7
1207 EK
2207 EK, 1307 EK, 22207 EK
2307 EK
114
40
58
58
58
31
36
46
10 M 40x1.5
10 M 40x1.5
10 M 40x1.5
0.19
0.22
0.28
HE 208
HE 308
HE 2308
KM 8
KM 8
KM 8
MB 8
MB 8
MB 8
1208 EK
2208 EK, 1308 EK, 22208 EK, 21308 CCK
2308 EK, 22308 EK
138
40
58
58
31
36
10 M 40x1.5
10 M 40x1.5
0.16
0.17
HS 208
HS 308
KM 8
KM 8
MB 8
MB 8
1208 EK
2208 EK, 1308 EK, 22208 EK, 21308 CCK
1716
45
65
65
65
33
39
50
11 M 45x1.5
11 M 45x1.5
11 M 45x1.5
0.26
0.29
0.35
HA 209
HA 309
HA 2309
KM 9
KM 9
KM 9
MB 9
MB 9
MB 9
1209 EK
2209 EK, 1309 EK, 22209 EK, 21309 CCK
2309 EK, 22309 EK
112
45
65
65
65
33
39
50
11 M 45x1.5
11 M 45x1.5
11 M 45x1.5
0.2
0.24
0.31
HE 209
HE 309
HE 2309
KM 9
KM 9
KM 9
MB 9
MB 9
MB 9
1209 EK
2209 EK, 1309 EK, 22209 EK, 21309 CCK
2309 EK, 22309 EK
158
50
70
70
70
35
42
55
12 M 50x1.5
12 M 50x1.5
12 M 50x1.5
0.31
0.36
0.4
HS 210
HS 310
HS 2310
KM 10
KM 10
KM 10
MB 10
MB 10
MB 10
HMV 10
HMV 10
HMV 10
1210 EK
2210 EK, 1310 EK, 22210 EK, 21310 CCK
2310 EK, 22310 EK
11116
50
70
70
70
35
42
55
12 M 50x1.5
12 M 50x1.5
12 M 50x1.5
0.28
0.32
0.4
HA 210
HA 310
HA 2310
KM 10
KM 10
KM 10
MB 10
MB 10
MB 10
HMV 10
HMV 10
HMV 10
1210 EK
2210 EK, 1310 EK, 22210 EK, 21310 CCK
2310 EK, 22310 EK
15
542
Adapter sleeves
d1 134 21116 in
Type HA, HE, HS
Dimensions
d1
Mass
d3
B1
B2
in
Designations
Adapter sleeve
with lock nut
and locking
device
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
kg
0.26
0.29
0.36
HE 210
HE 310
HE 2310
KM 10
KM 10
KM 10
MB 10
MB 10
MB 10
HMV 10
HMV 10
HMV 10
1210 EK
2210 EK, 1310 EK, 22210 EK, 21310 CCK
2310 EK, 22310 EK
134
50
70
70
70
35
42
55
12
12
12
178
55
75
75
37
45
12.5 M 55x2
12.5 M 55x2
0.33
0.38
HS 211
HS 311
KM 11
KM 11
MB 11
MB 11
HMV 11
HMV 11
1211 EK
2211 EK, 1311 EK, 22211 EK, 21311 CCK
11516
55
75
75
75
37
45
59
12.5 M 55x2
12.5 M 55x2
12.5 M 55x2
0.3
0.34
0.42
HA 211
HA 311
HA 2311
KM 11
KM 11
KM 11
MB 11
MB 11
MB 11
HMV 11
HMV 11
HMV 11
1211 EK
2211 EK, 1311 EK, 22211 EK, 21311 CCK
2311 K, 22311 EK
55
75
75
75
37
45
59
12.5 W 55x1/19 0.26

12.5 W 55x1/19 0.29
12.5 W 55x1/19 0.36
HE 211 B
HE 311 B
HE 2311 B
HM 11
HM 11
HM 11
MB 11
MB 11
MB 11
1211 EK
2211 EK, 1311 EK, 22211 EK, 21311 CCK
2311 K, 22311 EK
218
60
80
80
80
38
47
62
13
13
13
M 60x2
M 60x2
M 60x2
0.35
0.4
0.49
HS 212
HS 312
HS 2312
KM 12
KM 12
KM 12
MB 12
MB 12
MB 12
HMV 12
HMV 12
HMV 12
1212 EK
2212 EK, 1312 EK, 22212 EK, 21312 CCK
2312 K, 22312 EK
2316
65
85
85
85
40
50
65
14
14
14
M 65x2
M 65x2
M 65x2
0.49
0.58
0.75
HA 213
HA 313
HA 2313
KM 13
KM 13
KM 13
MB 13
MB 13
MB 13
HMV 13
HMV 13
HMV 13
1213 EK
2213 EK, 1313 EK, 22213 EK, 21313 CCK
2313 K, 22313 EK
214
65
85
85
85
40
50
65
14
14
14
M 65x2
M 65x2
M 65x2
0.44
0.52
0.65
HE 213
HE 313
HE 2313
KM 13
KM 13
KM 13
MB 13
MB 13
MB 13
HMV 13
HMV 13
HMV 13
1213 EK
2213 EK, 1313 EK, 22213 EK, 21313 CCK
2313 K, 22313 EK
238
65
85
85
85
40
50
65
14
14
14
M 65x2
M 65x2
M 65x2
0.44
0.71
0.80
HS 213
HS 313
HS 2313
KM 13
KM 13
KM 13
MB 13
MB 13
MB 13
HMV 13
HMV 13
HMV 13
1213 EK
2213 EK, 1313 EK, 22213 EK, 21313 CCK
2313 K, 22313 EK
2716
75
98
98
98
43
55
73
15
15
15
M 75x2
M 75x2
M 75x2
0.75
0.91
1.15
HA 215
HA 315
HA 2315
KM 15
KM 15
KM 15
MB 15
MB 15
MB 15
HMV 15
HMV 15
HMV 15
1215 K
2215 K, 1315 K, 22215 EK, 21315 CCK
2315 K, 22315 EK
212
75
98
98
98
43
55
73
15
15
15
M 75x2
M 75x2
M 75x2
0.7
0.85
1.09
HE 215
HE 315
HE 2315
KM 15
KM 15
KM 15
MB 15
MB 15
MB 15
HMV 15
HMV 15
HMV 15
1215 K
2215 K, 1315 K, 22215 EK, 21315 CCK
2315 K, 22315 EK
258
75
98
98
98
43
55
73
15
15
15
M 75x2
M 75x2
M 75x2
0.7
0.71
0.9
HS 215
HS 315
HS 2315
KM 15
KM 15
KM 15
MB 15
MB 15
MB 15
HMV 15
HMV 15
HMV 15
1215 K
2215 K, 1315 K, 22215 EK, 21315 CCK
2315 K, 22315 EK
21116
80
105 46
105 59
105 78
17
17
17
M 80x2
M 80x2
M 80x2
0.87
1.05
1.3
HA 216
HA 316
HA 2316
KM 16
KM 16
KM 16
MB 16
MB 16
MB 16
HMV 16
HMV 16
HMV 16
1216 K
2216 EK, 1316 K, 22216 EK, 21316 CCK
2316 K, 22316 EK
M 50x1.5
M 50x1.5
M 50x1.5
543

Adapter sleeves
d1 234 4 in
Type HA, HE
Dimensions
d1
Mass
d3
B1
B2
in
Designations
Adapter sleeve
with lock nut
and locking
device
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
234
80
105
105
105
46
59
78
17
17
17
M 80x2
M 80x2
M 80x2
0.81
0.97
1.2
HE 216
HE 316
HE 2316
KM 16
KM 16
KM 16
MB 16
MB 16
MB 16
HMV 16
HMV 16
HMV 16
1216 K
2216 EK, 1316 K, 22216 EK, 21316 CCK
2316 K, 22316 EK
21516
85
110
110
110
50
63
82
18
18
18
M 85x2
M 85x2
M 85x2
0.94
1.1
1.4
HA 217
HA 317
HA 2317
KM 17
KM 17
KM 17
MB 17
MB 17
MB 17
HMV 17
HMV 17
HMV 17
1217 K
2217 K, 1317 K, 22217 EK, 21317 CCK
2317 K, 22317 EK
85
110
110
110
50
63
82
18
18
18
M 85x2
M 85x2
M 85x2
0.87
1
1.3
HE 217
HE 317
HE 2317
KM 17
KM 17
KM 17
MB 17
MB 17
MB 17
HMV 17
HMV 17
HMV 17
1217 K
2217 K, 1317 K, 22217 EK, 21317 CCK
2317 K, 22317 EK
3316
90
120
120
120
52
65
86
18
18
18
M 90x2
M 90x2
M 90x2
1.05
1.25
1.5
HA 218
HA 318
HA 2318
KM 18
KM 18
KM 18
MB 18
MB 18
MB 18
HMV 18
HMV 18
HMV 18
1218 K
2218 K, 1318 K, 22218 EK, 21318 CCK
2318 K, 23218 CCK/W33, 22318 EK
314
90
120
120
120
52
65
86
18
18
18
M 90x2
M 90x2
M 90x2
0.97
1.1
1.4
HE 218
HE 318
HE 2318
KM 18
KM 18
KM 18
MB 18
MB 18
MB 18
HMV 18
HMV 18
HMV 18
1218 K
2218 K, 1318 K, 22218 EK, 21318 CCK
2318 K, 23218 CCK/W33, 22318 EK
95
125
125
125
55
68
90
19
19
19
M 95x2
M 95x2
M 95x2
1.35
1.6
2
HE 219
HE 319
HE 2319
KM 19
KM 19
KM 19
MB 19
MB 19
MB 19
HMV 19
HMV 19
HMV 19
1219 K
2219 K, 1319 K, 22219 EK, 21319 CCK
2319 K, 22319 EK
3716
100 130
130
130
58
71
97
20
20
20
M 100x2 1.55
M 100x2 1.8
M 100x2 2.35
HA 220
HA 320
HA 2320
KM 20
KM 20
KM 20
MB 20
MB 20
MB 20
HMV 20
HMV 20
HMV 20
1220 K
2220 K, 1320 K, 22220 EK, 21320 CCK
2320 K, 23220 CCK/W33, 22320 EK
312
100 130
130
130
130
58
71
97
76
20
20
20
20
M 100x2
M 100x2
M 100x2
M 100x2
HE 220
HE 320
HE 2320
HE 3120
KM 20
KM 20
KM 20
KM 20
MB 20
MB 20
MB 20
MB 20
HMV 20
HMV 20
HMV 20
HMV 20
1220 K
2220 K, 1320 K, 22220 EK, 21320 CCK
2320 K, 23220 CCK/W33, 22320 EK
23120 CCK/W33
31116
105 140
140
60
74
20
20
M 105x2 1.7
M 105x2 1.95
HA 221
HA 321
KM 21
KM 21
MB 21
MB 21
HMV 21
HMV 21
1221 K
2221 K, 1321 K
334
105 140
140
60
74
20
20
M 105x2 1.58
M 105x2 1.83
HE 221
HE 321
KM 21
KM 21
MB 21
MB 21
HMV 21
HMV 21
1221 K
2221 K, 1321 K
110 145
145
63
77
21
21
M 110x2 1.65
M 110x2 1.9
HE 222
HE 322
KM 22
KM 22
MB 22
MB 22
HMV 22
HMV 22
105 21
81 21
M 110x2 2.4
M 110x2 2.25
HE 2322
HE 3122
KM 22
KM 22
MB 22
MB 22
HMV 22
HMV 22
1222 K
2222 K, 1322 K, 23022 CCK, 22222 EK
21322 CCK
2322 K, 23222 CCK/W33, 22322 EK
23122 CCK/W33
145
145
1.45
1.75
2.2
1.8
544
Adapter sleeves
d1 4316 6 in
Type HA, HE
Dimensions
d1
Mass
d3
B1
B2
in
Designations
Adapter sleeve
with lock nut
and locking
device
kg
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
4316
120 145 72 22
155 88 22
155 112 22
M 120x2
M 120x2
M 120x2
2.25
2.9
3.6
HA 3024
HA 3124
HA 2324
KML 24
KM 24
KM 24
MBL 24
MB 24
MB 24
HMV 24
HMV 24
HMV 24
1224 K, 23024 CCK/W33

2224 K, 23124 CCK/W33
23224 CCK/W33, 22324 CCK/W33
414
120 145 72 22
155 88 22
155 112 22
M 120x2
M 120x2
M 120x2
2
2.8
3.35
HE 3024
HE 3124
HE 2324
KML 24
KM 24
KM 24
MBL 24
MB 24
MB 24
HMV 24
HMV 24
HMV 24
1224 K, 23024 CCK/W33

23124 CCK/W33, 22224 EK
23224 CCK/W33, 22324 CCK/W33
4716
130 155 80 23
165 92 23
165 121 23
M 130x2
M 130x2
M 130x2
2.85
3.75
4.75
HA 3026
HA 3126
HA 2326
KML 26
KM 26
KM 26
MBL 26
MB 26
MB 26
HMV 26
HMV 26
HMV 26
23026 CCK/W33
23126 CCK/W33, 22226 EK
23226 CCK/W33, 22326 CCK/W33
412
130 155 80 23
165 92 23
165 121 23
M 130x2
M 130x2
M 130x2
2.9
3.6
4.55
HE 3026
HE 3126
HE 2326
KML 26
KM 26
KM 26
MBL 26
MB 26
MB 26
HMV 26
HMV 26
HMV 26
23026 CCK/W33
23126 CCK/W33, 22226 EK
23226 CCK/W33, 22326 CCK/W33
41516
140 165 82 24
180 97 24
180 131 24
M 140x2
M 140x2
M 140x2
3
4.1
5.3
HA 3028
HA 3128
HA 2328
KML 28
KM 28
KM 28
MBL 28
MB 28
MB 28
HMV 28
HMV 28
HMV 28
23028 CCK/W33
23128 CCK/W33, 22228 CCK/W33
23228 CCK/W33, 22328 CCK/W33
140 165 82 24
180 97 24
180 131 24
M 140x2
M 140x2
M 140x2
2.8
3.15
5
HE 3028
HE 3128
HE 2328
KML 28
KM 28
KM 28
MBL 28
MB 28
MB 28
HMV 28
HMV 28
HMV 28
23028 CCK/W33
23128 CCK/W33, 22228 CCK/W33
23228 CCK/W33, 22328 CCK/W33
5316
150 180 87 26
195 111 26
195 139 26
M 150x2
M 150x2
M 150x2
4.7
5.8
7.1
HA 3030
HA 3130
HA 2330
KML 30
KM 30
KM 30
MBL 30
MB 30
MB 30
HMV 30
HMV 30
HMV 30
23030 CCK/W33
23130 CCK/W33, 22230 CCK/W33
23230 CCK/W33, 22330 CCK/W33
514
150 180 87 26
195 111 26
195 139 26
M 150x2
M 150x2
M 150x2
4.65
5.5
6.8
HE 3030
HE 3130
HE 2330
KML 30
KM 30
KM 30
MBL 30
MB 30
MB 30
HMV 30
HMV 30
HMV 30
23030 CCK/W33
23130 CCK/W33, 22230 CCK/W33
23230 CCK/W33, 22330 CCK/W33
5716
160 190 93 27.5 M 160x3

210 119 28
M 160x3
210 147 28
M 160x3
5.2
7.55
9.4
HA 3032
HA 3132
HA 2332
KML 32
KM 32
KM 32
MBL 32
MB 32
MB 32
HMV 32
HMV 32
HMV 32
23032 CCK/W33
23132 CCK/W33, 22232 CCK/W33
23232 CCK/W33, 22332 CCK/W33
512
160 190 93 27.5 M 160x3

210 119 28
M 160x3
210 147 28
M 160x3
5.1
7.3
8.8
HE 3032
HE 3132
HE 2332
KML 32
KM 32
KM 32
MBL 32
MB 32
MB 32
HMV 32
HMV 32
HMV 32
23032 CCK/W33
23132 CCK/W33, 22232 CCK/W33
23232 CCK/W33, 22332 CCK/W33
51516
170 200 101 28.5 M 170x3

220 122 29
M 170x3
220 154 29
M 170x3
5.7
7.8
9.6
HA 3034
HA 3134
HA 2334
KML 34
KM 34
KM 34
MBL 34
MB 34
MB 34
HMV 34
HMV 34
HMV 34
23034 CCK/W33
23134 CCK/W33, 22234 CCK/W33
23234 CCK/W33, 22334 CCK/W33
170 200 101 28.5 M 170x3

220 122 29
M 170x3
220 154 29
M 170x3
5.4
7.55
9.2
HE 3034
HE 3134
HE 2334
KML 34
KM 34
KM 34
MBL 34
MB 34
MB 34
HMV 34
HMV 34
HMV 34
23034 CCK/W33
23134 CCK/W33, 22234 CCK/W33
23234 CCK/W33, 22334 CCK/W33
545

Adapter sleeves
d1 6716 7316 in
Type HA, HE
Dimensions
d1
in
Mass
d3
B1
B2
G
kg
Designations
Adapter sleeve
with lock nut
and locking
device
Lock
nut
Locking
device
Appropriate
hydraulic
nut
Bearing(s)
6716
180 210 109 29.5 M 180x3 6.85

230 131 30
M 180x3 8.15
230 161 30
M 180x3 9.9
HA 3036
HA 3136
HA 2336
KML 36
KM 36
KM 36
MBL 36
MB 36
MB 36
HMV 36
HMV 36
HMV 36
23036 CCK/W33
23136 CCK/W33, 22236 CCK/W33
23236 CCK/W33, 22336 CCK/W33
612
180 210 109 29.5 M 180x3 5.55

230 131 30
M 180x3 7.8
230 161 30
M 180x3 9.35
HE 3036
HE 3136
HE 2336
KML 36
KM 36
KM 36
MBL 36
MB 36
MB 36
HMV 36
HMV 36
HMV 36
23036 CCK/W33
23136 CCK/W33, 22236 CCK/W33
23236 CCK/W33, 22336 CCK/W33
634
190 220 112 30.5 M 190x3 7.2

240 141 31
M 190x3 10.2
240 169 31
M 190x3 11.7
HE 3038
HE 3138
HE 2338
KML 38
KM 38
KM 38
MBL 38
MB 38
MB 38
HMV 38
HMV 38
HMV 38
23038 CCK/W33
23138 CCK/W33, 22238 CCK/W33
23238 CCK/W33, 22338 CCK/W33
61516
190 220 112 30.5 M 190x3 7.2

240 141 31
M 190x3 8.5
240 169 31
M 190x3 10
HA 3038
HA 3138
HA 2338
KML 38
KM 38
KM 38
MBL 38
MB 38
MB 38
HMV 38
HMV 38
HMV 38
23038 CCK/W33
23138 CCK/W33, 22238 CCK/W33
23238 CCK/W33, 22338 CCK/W33
200 240 120 31.5 M 200x3 9.35

250 150 32
M 200x3 12.3
250 176 32
M 200x3 14.2
HE 3040
HE 3140
HE 2340
KML 40
KM 40
KM 40
MBL 40
MB 40
MB 40
HMV 40
HMV 40
HMV 40
23040 CCK/W33
23140 CCK/W33, 22240 CCK/W33
23240 CCK/W33, 22340 CCK/W33
7316
200 240 120 31.5 M 200x3 8.5

250 150 32
M 200x3 10.8
250 176 32
M 200x3 12.6
HA 3040
HA 3140
HA 2340
KML 40
KM 40
KM 40
MBL 40
MB 40
MB 40
HMV 40
HMV 40
HMV 40
23040 CCK/W33
23140 CCK/W33, 22240 CCK/W33
23240 CCK/W33, 22340 CCK/W33
546
Withdrawal sleeves
d1 35 95 mm
Type AH, AHX
Dimensions
d1
B1
Mass
B21)
Designations
Withdrawal
sleeve
G1
mm
kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
35
40
29
40
32
43
M 45x1.5
M 45x1.5
6
7
0.09
0.13
AH 308
AH 2308
KM 9
KM 9
KM 7
KM 7
MB 7
MB 7
2208 EK,1308 EK, 22208 EK, 21308 CCK

2308 EK, 22308 EK
40
45
31
44
34
47
M 50x1.5
M 50x1.5
6
7
0.12
0.16
AH 309
AH 2309
KM 10
KM 10
HMV 10
HMV 10
KM 8
KM 8
MB 8
MB 8
2209 EK, 1309 EK, 22209 EK, 21309 CCK

2309 EK, 22309 EK
45
50
35
50
38
53
M 55x2
M 55x2
7
9
0.13
0.19
AHX 310
AHX 2310
KM 11
KM 11
HMV 11
HMV 11
KM 9
KM 9
MB 9
MB 9
2210 EK, 1310 EK, 22210 EK, 21310 CCK

2310 K, 22310 EK
50
55
37
54
40
57
M 60x2
M 60x2
7
10
0.16
0.26
AHX 311
AHX 2311
KM 12
KM 12
HMV 12
HMV 12
KM 10
KM 10
MB 10
MB 10
2211 EK, 1311 EK, 22211 EK, 21311 CCK

2311 K, 22311 EK
55
60
40
58
43
61
M 65x2
M 65x2
8
11
0.19
0.3
AHX 312
AHX 2312
KM 13
KM 13
HMV 13
HMV 13
KM 11
KM 11
MB 11
MB 11
2212 EK, 1312 EK, 22212 EK, 21312 CCK

2312 K, 22312 EK
60
65
42
61
45
64
M 70x2
M 70x2
8
12
0.23
0.36
AH 313 G
AH 2313 G
KM 14
KM 14
HMV 14
HMV 14
KM 12
KM 12
MB 12
MB 12
2213 EK, 1313 EK, 22213 EK, 21313 CCK

2313 K, 22313 EK
65
70
43
64
47
68
M 75x2
M 75x2
8
12
0.25
0.42
AH 314 G
AHX 2314 G
KM 15
KM 15
HMV 15
HMV 15
KM 13
KM 13
MB 13
MB 13
22214 EK, 21314 CCK

22314 EK
70
75
45
68
49
72
M 80x2
M 80x2
8
12
0.3
0.48
AH 315 G
AHX 2315 G
KM 16
KM 16
HMV 16
HMV 16
KM 14
KM 14
MB 14
MB 14
2215 K, 1315 K, 22215 EK, 21315 CCK

2315 K, 22315 EK
75
80
48
71
52
75
M 90x2
M 90x2
8
12
0.37
0.57
AH 316
AHX 2316
KM 18
KM 18
HMV 18
HMV 18
KM 15
KM 15
MB 15
MB 15
2216 EK, 1316 K, 22216 EK, 21316 CCK

2316 K, 22316 EK
80
85
52
74
56
78
M 95x2
M 95x2
9
13
0.43
0.65
AHX 317
AHX 2317
KM 19
KM 19
HMV 19
HMV 19
KM 16
KM 16
MB 16
MB 16
2217 K, 1317 K, 22217 EK, 21317 CCK

2317 K, 22317 EK
85
90
53
79
63
57
83
67
M 100x2
M 100x2
M 100x2
9
14
10
0.46
0.76
0.57
AHX 318
AHX 2318
AHX 3218
KM 20
KM 20
KM 20
HMV 20
HMV 20
HMV 20
KM 17
KM 17
KM 17
MB 17
MB 17
MB 17
2218 K, 1318 K, 22218 EK, 21318 CCK

2318 K, 22318 EK
23218 CCK/W33
90
95
57
85
61
89
M 105x2
M 105x2
10
16
0.54
0.9
AHX 319
AHX 2319
KM 21
KM 21
HMV 21
HMV 21
KM 18
KM 18
MB 18
MB 18
2219 K, 1319 K, 22219 EK, 21319 CCK

2319 K, 22319 EK
95
100 59
64
73
90
63
68
77
94
M 110x2
M 110x2
M 110x2
M 110x2
10
11
11
16
0.58
0.66
0.76
1
AHX 320
AHX 3120
AHX 3220
AHX 2320
KM 22
KM 22
KM 22
KM 22
HMV 22
HMV 22
HMV 22
HMV 22
KM 19
KM 19
KM 19
KM 19
MB 19
MB 19
MB 19
MB 19
2220 K, 1320 K, 22220 EK, 21320 CCK

23120 CCK/W33
23220 CCK/W33
2320 K, 22320 EK
1) Width before the sleeve is pressed into the bearing bore
547

Withdrawal sleeves
d1 105 150 mm
Type AH, AHX
Dimensions
d1
B1
Mass
B21)
G1
mm
105 110 63
98
68
Designations
Withdrawal
sleeve
kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
67
102
72
M 120x2
M 120x2
M 120x2
12
16
11
0.77
1.28
0.76
AHX 322
AHX 2322 G
AHX 3122
KM 24
KM 24
KM 24
HMV 24
HMV 24
HMV 24
KM 21
KM 21
KM 21
MB 21
MB 21
MB 21
86
91
M 120x2
M 115x2
11
13
1
0.71
AHX 3222 G
AH 24122
KM 24
KM 23
HMV 24
HMV 23
KM 21
KM 21
MB 21
MB 21
1322 K, 21322 CCK

2322 K, 22322 EK
2222 K, 23122 CCK/W33,
22222 EK, 21322 CCK
23222 CCK/W33
24122 CCK30/W33
115 120 105

60
75
90
73
93
109
64
79
94
82
102
M 130x2
M 130x2
M 130x2
M 130x2
M 125x2
M 130x2
17
13
12
13
13
13
1.53
0.73
0.94
1 70
0 70
1
AHX 2324 G
AHX 3024
AHX 3124
AHX 3224 G
AH 24024
AH 24124
KM 26
KM 26
KM 26
KM 26
KM 25
KM 26
HMV 26
HMV 26
HMV 26
HMV 26
HMV 25
HMV 26
KM 22
KM 22
KM 22
KM 22
KM 22
KM 22
MB 22
MB 22
MB 22
MB 22
MB 22
MB 22
22324 CCK/W33
23024 CCK/W33
23124 CCK/W33, 22224 EK
23224 CCK/W33
24024 CCK30/W33
24124 CCK30/W33
125 130 115

67
78
98
83
94
119
71
82
102
93
104
M 140x2
M 140x2
M 140x2
M 140x2
M 135x2
M 140x2
19
14
12
15
14
14
1.9
0.91
1.1
1.5
0.88
1.15
AHX 2326 G
AHX 3026
AHX 3126
AHX 3226 G
AH 24026
AH 24126
KM 28
KM 28
KM 28
KM 28
KM 27
KM 28
HMV 28
HMV 28
HMV 28
HMV 28
HMV 27
HMV 28
KM 24
KM 24
KM 24
KM 24
KM 24
KM 24
MB 24
MB 24
MB 24
MB 24
MB 24
MB 24
22326 CCK/W33
23026 CCK/W33
23126 CCK/W33, 22226 EK
23226 CCK/W33
24026 CCK30/W33
24126 CCK30/W33
135 140 125

68
83
104
83
99
130
73
88
109
93
109
M 150x2
M 150x2
M 150x2
M 150x2
M 145x2
M 150x2
20
14
14
15
14
14
2.25
1
1.3
1.8
0.95
1.3
AHX 2328 G
AHX 3028
AHX 3128
AHX 3228 G
AH 24028
AH 24128
KM 30
KM 30
KM 30
KM 30
KM 29
KM 30
HMV 30
HMV 30
HMV 30
HMV 30
HMV 29
HMV 30
KM 26
KM 26
KM 26
KM 26
KM 26
KM 26
MB 26
MB 26
MB 26
MB 26
MB 26
MB 26
22328 CCK/W33
23028 CCK/W33
23128 CCK/W33, 22228 EK
23228 CCK/W33
24028 CCK30/W33
24128 CCK30/W33
145 150 135

72
96
114
90
115
140
77
101
119
101
126
M 160x3
M 160x3
M 160x3
M 160x3
M 155x3
M 160x3
24
15
15
17
15
15
3.7
1.15
1.7
210
1 05
1.55
AHX 2330 G
AHX 3030
AHX 3130 G
AHX 3230 G
AH 24030
AH 24130
KM 32
KM 32
KM 32
KM 32
KM 31
KM 32
HMV 32
HMV 32
HMV 32
HMV 32
HMV 31
HMV 32
KM 28
KM 28
KM 28
KM 28
KM 28
KM 28
MB 28
MB 28
MB 28
MB 28
MB 28
MB 28
22330 CCK/W33
23030 CCK/W33
23130 CCK/W33, 22230 CCK/W33
23230 CCK/W33
24030 CCK30/W33
24130 CCK30/W33
150 160 140

77
103
124
95
124
146
82
108
130
106
135
M 170x3
M 170x3
M 170x3
M 170x3
M 170x3
M 170x3
24
16
16
20
15
15
4.3
2.05
3
3.7
2.3
3
AH 2332 G
AH 3032
AH 3132 G
AH 3232 G
AH 24032
AH 24132
KM 34
KM 34
KM 34
KM 34
KM 34
KM 34
HMV 34
HMV 34
HMV 34
HMV 34
HMV 34
HMV 34
KM 30
KM 30
KM 30
KM 30
KM 30
KM 30
MB 30
MB 30
MB 30
MB 30
MB 30
MB 30
22332 CCK/W33
23032 CCK/W33
23132 CCK/W33, 22232 CCK/W33
23232 CCK/W33
24032 CCK30/W33
24132 CCK30/W33
82
82
548
Withdrawal sleeves
d1 160 200 mm
Type AH
Type AOH
Dimensions
d1 d
Mass
1)
B1 B2
G1
mm
Designations
Withdrawal
sleeve
G2
in
mm kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
160 170 146 152 M 180x3

85 90 M 180x3
104 109 M 180x3
24
17
16
4.85
2.45
3.2
AH 2334 G
AH 3034
AH 3134 G
KM 36
KM 36
KM 36
HMV 36
HMV 36
HMV 36
KM 32
KM 32
KM 32
MB 32
MB 32
MB 32
134 140 M 180x3

106 117 M 180x3
125 136 M 180x3
24
16
16
4.35
2.7
3.25
AH 3234 G
AH 24034
AH 24134
KM 36
KM 36
KM 36
HMV 36
HMV 36
HMV 36
KM 32
KM 32
KM 32
MB 32
MB 32
MB 32
22334 CCK/W33
23034 CCK/W33
23134 CCK/W33,
22234 CCK/W33
23234 CCK/W33
24034 CCK30/W33
24134 CCK30/W33
170 180 105

154
92
116
140
116
134
110
160
98
122
146
127
145
M 190x3
M 190x3
M 190x3
M 190x3
M 190x3
M 190x3
M 190x3
17
26
17
19
24
16
16
3.4
5.5
2.8
3.9
485
320
3.75
AH 2236 G
AH 2336 G
AH 3036
AH 3136 G
AH 3236 G
AH 24036
AH 24136
KM 38
KM 38
KM 38
KM 38
KM 38
KM 38
KM 38
HMV 38
HMV 38
HMV 38
HMV 38
HMV 38
HMV 38
HMV 38
KM 34
KM 34
KM 34
KM 34
KM 34
KM 34
KM 34
MB 34
MB 34
MB 34
MB 34
MB 34
MB 34
MB 34
22236 CCK/W33
22336 CCK/W33
23036 CCK/W33
23136 CCK/W33
23236 CCK/W33
24036 CCK30/W33
24136 CCK30/W33
180 190 112

160
96
125
145
118
146
117
167
102
131
152
131
159
M 200x3
M 200x3
M 200x3
M 200x3
M 200x3
M 200x3
M 200x3
18
26
18
20
25
18
18
3.9
6.1
3.3
4.5
5.4
3.55
4.45
AH 2238 G
AH 2338 G
AH 3038 G
AH 3138 G
AH 3238 G
AH 24038
AH 24138
KM 40
KM 40
KM 40
KM 40
KM 40
KM 40
KM 40
HMV 40
HMV 40
HMV 40
HMV 40
HMV 40
HMV 40
HMV 40
KM 36
KM 36
KM 36
KM 36
KM 36
KM 36
KM 36
MB 36
MB 36
MB 36
MB 36
MB 36
MB 36
MB 36
22238 CCK/W33
22338 CCK/W33
23038 CCK/W33
23138 CCK/W33
23238 CCK/W33
24038 CCK30/W33
24138 CCK30/W33
190 200 118

170
102
134
153
127
158
123
177
108
140
160
140
171
Tr 220x4
Tr 220x4
Tr 210x4
Tr 220x4
Tr 220x4
Tr 210x4
Tr 210x4
19
30
19
21
25
18
18
4.7
7.6
3.7
5.65
6.6
4
5.05
AH 2240
AH 2340
AH 3040 G
AH 3140
AH 3240
AH 24040
AH 24140
HM 44 T
HM 44 T
HM 42 T
HM 44 T
HM 44 T
HM 42 T
HM 42 T
HMV 44
HMV 44
HMV 42
HMV 44
HMV 44
HMV 42
HMV 42
KM 38
KM 38
KM 38
KM 38
KM 38
KM 38
KM 38
MB 38
MB 38
MB 38
MB 38
MB 38
MB 38
MB 38
22240 CCK/W33
22340 CCK/W33
23040 CCK/W33
23140 CCK/W33
23240 CCK/W33
24040 CCK/W33
24140 CCK30/W33
200 220 181 189 Tr 240x4
30
G 1/4
13.5
AOH 2344
HM 48 T
HMV 48
KM 40
MB 40
20
23
20
20
20
G 1/8
G 1/4
G 1/4
G 1/8
G 1/8
6.5
9
9
6.5
6.5
7.3
9.3
9.4
8.2
10
AOH 3044 G
AOH 3144
AOH 2244
AOH 24044
AOH 24144
HM 46 T
HM 48 T
HM 48 T
HM 46 T
HM 46 T
HMV 46
HMV 48
HMV 48
HMV 46
HMV 46
KM 40
KM 40
KM 40
KM 40
KM 40
MB 40
MB 40
MB 40
MB 40
MB 40
23244 CCK/W33,
22344 CCK/W33
23044 CCK/W33
23144 CCK/W33
22244 CCK/W33
24044 CCK30/W33
24144 CCK30/W33
111
145
130
138
170
117
151
136
152
184
Tr 230x4
Tr 240x4
Tr 240x4
Tr 230x4
Tr 230x4
549

Withdrawal sleeves
d1 220 320 mm
Type AOH
Dimensions
d1 d
Mass
1)
B1 B2
G1
Designations
Withdrawal
sleeve
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
23248 CCK/W33,
22348 CCK/W33
23048 CCK/W33
23148 CCK/W33
22248 CCK/W33
24048 CCK30/W33
24148 CCK30/W33
G2
in
mm kg
30
G 1/4
14
AOH 2348
HM 52 T
HMV 52
HM 44 T
MB 44
Tr 260x4
Tr 260x4
Tr 260x4
Tr 250x4
Tr 260x4
21
25
21
20
20
G 1/4
G 1/4
G 1/4
G 1/8
G 1/4
9
9
9
6.5
9
7.95
12
11.5
8.05
11.5
AOH 3048
AOH 3148
AOH 2248
AOH 24048
AOH 24148
HM 52 T
HM 52 T
HM 52 T
HM 50 T
HM 52 T
HMV 52
HMV 52
HMV 52
HMV 50
HMV 52
HM 44 T
HM 44 T
HM 44 T
HM 44 T
HM 44 T
MB 44
MB 44
MB 44
MB 44
MB 44
240 260 155 161 Tr 280x4

205 213 Tr 280x4
23
30
G 1/4
G 1/4
9
9
13.5
19
AOH 2252 G
AOH 2352 G
HM 56 T
HM 56 T
HMV 56
HMV 56
HM 48 T
HM 48 T
MB 48
MB 48
Tr 280x4
Tr 280x4
Tr 280x4
Tr 280x4
23
26
22
22
G 1/4
G 1/4
G 1/8
G 1/4
9
9
6.5
9
9.6
15.5
12.5
14
AOH 3052
AOH 3152 G
AOH 24052 G
AOH 24152
HM 56 T
HM 56 T
HM 56 T
HM 56 T
HMV 56
HMV 56
HMV 56
HMV 56
HM 48 T
HM 48 T
HM 48 T
HM 48 T
MB 48
MB 48
MB 48
MB 48
260 280 155 163 Tr 300x4

212 220 Tr 300x4
24
30
G 1/4
G 1/4
9
9
14.8
21.5
AOH 2256 G
AOH 2356 G
HM 3160
HM 3160
HMV 60
HMV 60
HM 52 T
HM 52 T
MB 52
MB 52
mm
220 240 189 197 Tr 260x4
116
154
144
138
180
128
172
162
202
123
161
150
153
195
135
179
178
218
22252 CACK/W33
23252 CACK/W33,
22352 CCK/W33
23052 CCK/W33
23152 CCK/W33
24052 CCK30/W33
24152 CCK30/W33
131
175
162
202
139
183
179
219
Tr 300x4
Tr 300x4
Tr 300x4
Tr 300x4
24
28
22
22
G 1/4
G 1/4
G 1/8
G 1/4
9
9
6.5
9
11
17
13.5
15
AOH 3056
AOH 3156 G
AOH 24056 G
AOH 24156
HM 3060
HM 3160
HM 3160
HM 3160
HMV 60
HMV 60
HMV 60
HMV 60
HM 52 T
HM 52 T
HM 52 T
HM 52 T
MB 52
MB 52
MB 52
MB 52
22256 CACK/W33
23256 CACK/W33,
22356 CCK/W33
23056 CCK/W33
23156 CCK/W33
24056 CCK30/W33
24156 CCK30/W33
280 300 170

145
192
228
184
224
178
153
200
236
202
242
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
Tr 320x5
26
26
30
34
24
24
G 1/4
G 1/4
G 1/4
G 1/4
G 1/8
G 1/4
9
9
9
9
6.5
9
17.5
13
20.5
23.5
17
18.5
AOH 2260 G
AOH 3060
AOH 3160 G
AOH 3260 G
AOH 24060 G
AOH 24160
HM 3164
HM 3064
HM 3164
HM 3164
HM 3164
HM 3164
HMV 64
HMV 64
HMV 64
HMV 64
HMV 64
HMV 64
HM 56 T
HM 56 T
HM 56 T
HM 56 T
HM 56 T
HM 56 T
MB 56
MB 56
MB 56
MB 56
MB 56
MB 56
22260 CACK/W33
23060 CCK/W33
23160 CCK/W33
23260 CACK/W33
24060 CCK30/W33
24160 CCK30/W33
300 320 180

149
209
246
184
242
190
157
217
254
202
260
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
Tr 340x5
27
27
31
36
24
24
G 1/4
G 1/4
G 1/4
G 1/4
G 1/8
G 1/4
9
9
9
9
6.5
9
20
16.5
24.5
27.5
18
20.5
AOH 2264 G
AOH 3064 G
AOH 3164 G
AOH 3264 G
AOH 24064 G
AOH 24164
HM 3168
HM 3068
HM 3168
HM 3168
HM 3168
HM 3168
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
HMV 68
HM 3060
HM 3060
HM 3060
HM 3060
HM 3060
HM 3060
MS 3060
MS 3060
MS 3060
MS 3060
MS 3060
MS 3060
22264 CACK/W33
23064 CCK/W33
23164 CCK/W33
23264 CACK/W33
24064 CCK30/W33
24164 CCK30/W33
320 340 162

225
264
206
269
171
234
273
225
288
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
Tr 360x5
28
33
38
26
26
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
19
28
32
18
25.5
AOH 3068 G
AOH 3168 G
AOH 3268 G
AOH 24068
AOH 24168
HM 3072
HM 3172
HM 3172
HM 3172
HM 3172
HMV 72
HMV 72
HMV 72
HMV 72
HMV 72
HM 3064
HM 3064
HM 3064
HM 3064
HM 3064
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
23068 CCK/W33
23168 CCK/W33
23268 CAK/W33
24068 CCK30/W33
24168 ECAK30/W33
550
Withdrawal sleeves
d1 340 670 mm
Type AOH, AOHX
Dimensions
d1 d
Mass
1)
B1 B2
G1
mm
Designations
Withdrawal
sleeve
G2
in
mm kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
340 360 167

229
274
206
269
176
238
283
226
289
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
Tr 380x5
30
35
40
26
26
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
21
30.5
35.5
20
26
AOH 3072 G
AOH 3172 G
AOH 3272 G
AOH 24072
AOH 24172
HM 3076
HM 3176
HM 3176
HM 3176
HM 3176
HMV 76
HMV 76
HMV 76
HMV 76
HMV 76
HM 3068
HM 3068
HM 3068
HM 3068
HM 3068
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
MS 3068-64
23072 CCK/W33
23172 CACK/W33
23272 CAK/W33
24072 CCK30/W33
24172 CCK30/W33
360 380 170

232
284
208
271
180
242
294
228
291
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
Tr 400x5
31
36
42
28
28
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
23
33
42
23.5
31
AOH 3076 G
AOH 3176 G
AOH 3276 G
AOH 24076
AOH 24176
HM 3080
HM 3180
HM 3180
HM 3180
HM 3180
HMV 80
HMV 80
HMV 80
HMV 80
HMV 80
HM 3072
HM 3072
HM 3072
HM 3072
HM 3072
MS 3072
MS 3072
MS 3072
MS 3072
MS 3072
23076 CCK/W33
23176 CAK/W33
23276 CAK/W33
24076 CCK30/W33
24176 CAK30/W33
380 400 183

240
302
228
278
193
250
312
248
298
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
Tr 420x5
33
38
44
28
28
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
26
36
48
27
35
AOH 3080 G
AOH 3180 G
AOH 3280 G
AOH 24080
AOH 24180
HM 3084
HM 3184
HM 3184
HM 3184
HM 3184
HMV 84
HMV 84
HMV 84
HMV 84
HMV 84
HM 3076
HM 3076
HM 3076
HM 3076
HM 3076
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
23080 CACK/W33
23180 CAK/W33
23280 CAK/W33
24080 CACK30/W33
24180 CCK30/W33
400 420 186

266
321
230
310
196
276
331
252
332
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
Tr 440x5
34
40
46
30
30
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
28
43
54.5
29
39
AOH 3084 G
AOH 3184 G
AOH 3284 G
AOH 24084
AOH 24184
HM 3088
HM 3188
HM 3188
HM 3188
HM 3188
HMV 88
HMV 88
HMV 88
HMV 88
HMV 88
HM 3080
HM 3080
HM 3080
HM 3080
HM 3080
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
MS 3080-76
23084 CAK/W33
23184 CK/W33
23284 CAK/W33
24084 CAK30/W33
24184 CAK30/W33
420 440 194

270
330
242
310
205
281
341
264
332
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
Tr 460x5
35
42
48
30
30
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
30.8
46
59
32
45.5
AOHX 3088 G
AOHX 3188 G
AOHX 3288 G
AOH 24088
AOH 24188
HM 3092
HM 3192
HM 3192
HM 3192
HM 3192
HMV 92
HMV 92
HMV 92
HMV 92
HMV 92
HM 3084
HM 3084
HM 3084
HM 3084
HM 3084
MS 3084
MS 3084
MS 3084
MS 3084
MS 3084
23088 CAK/W33
23188 CAK/W33
23288 CAK/W33
24088 CAK30/W33
24188 CAK30/W33
440 460 202

285
349
250
332
213
296
360
273
355
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
Tr 480x5
37
43
50
32
32
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
33.8
51.5
66.5
34.7
50
AOHX 3092 G
AOHX 3192 G
AOHX 3292 G
AOH 24092
AOH 24192
HM 3096
HM 3196
HM 3196
HM 3196
HM 3196
HMV 96
HMV 96
HMV 96
HMV 96
HMV 96
HM 3088
HM 3088
HM 3088
HM 3088
HM 3088
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
23092 CAK/W33
23192 CAK/W33
23292 CAK/W33
24092 CAK30/W33
24192 ECAK30/W33
460 480 205

295
364
250
340
217
307
376
273
363
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
Tr 500x5
38
45
52
32
32
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
36
56
73.5
36.6
51.5
AOHX 3096 G
AOHX 3196 G
AOHX 3296 G
AOH 24096
AOH 24196
HM 30/500
HM 31/500
HM 31/500
HM 31/500
HM 31/500
HMV 100
HMV 100
HMV 100
HMV 100
HMV 100
HM 3092
HM 3092
HM 3092
HM 3092
HM 3092
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
MS 3092-88
23096 CAK/W33
23196 CAK/W33
23296 CAK/W33
24096 CACK30/W33
24196 CAK30/W33
551

Withdrawal sleeves
d1 480 670 mm
Type AOH, AOHX
Dimensions
d1 d
Mass
1)
B1 B2
G1
mm
Designations
Withdrawal
sleeve
G2
in
mm kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
480 500 209

313
393
253
360
221
325
405
276
383
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
Tr 530x6
40
47
54
35
35
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
9
9
9
9
9
41
66.5
89.5
41.7
57
AOHX 30/500 G
AOHX 31/500 G
AOHX 32/500 G
AOH 240/500
AOH 241/500
HM 30/530
HM 31/530
HM 31/530
HM 31/530
HM 31/530
HMV 106
HMV 106
HMV 106
HMV 106
HMV 106
HM 3096
HM 3096
HM 3096
HM 3096
HM 3096
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
230/500 CAK/W33
231/500 CAK/W33
232/500 CAK/W33
240/500 CAK30/W33
241/500 ECAK30/W33
500 530 230

325
412
285
370
242
337
424
309
394
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
Tr 560x6
45
53
57
35
35
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
10
10
10
9
9
63.5
94.5
127
69.5
91.5
AOH 30/530
AOH 31/530
AOH 32/530 G
AOH 240/530 G
AOH 241/530 G
HM 30/560
HM 31/560
HM 31/560
HM 31/560
HM 31/560
HMV 112
HMV 112
HMV 112
HMV 112
HMV 112
HM 30/500
HM 30/500
HM 30/500
HM 30/500
HM 30/500
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
MS 30/500-96
230/530 CAK/W33
231/530 CAK/W33
232/530 CAK/W33
240/530 CAK30/W33
241/530 CAK30/W33
530 560 240

335
422
296
393
252
347
434
320
417
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
Tr 600x6
45
55
57
38
38
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
11
11
11
9
9
73.5
108
143
79.5
107
AOHX 30/560
AOH 31/560
AOHX 32/560
AOH 240/560 G
AOH 241/560 G
HM 30/600
HM 31/600
HM 31/600
HM 31/600
HM 31/600
HMV 120
HMV 120
HMV 120
HMV 120
HMV 120
HM 30/530
HM 30/530
HM 30/530
HM 30/530
HM 30/530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
230/560 CAK/W33
231/560 CAK/W33
232/560 CAK/W33
240/560 CAK30/W33
241/560 CAK30/W33
570 600 245

355
445
310
413
259
369
459
336
439
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
Tr 630x6
45
55
57
38
38
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
11
11
11
9
9
77
120
159
86.5
118
AOHX 30/600
AOHX 31/600
AOHX 32/600 G
AOHX 240/600
AOHX 241/600
HM 30/630
HM 31/630
HM 31/630
HM 31/630
HM 31/630
HMV 126
HMV 126
HMV 126
HMV 126
HMV 126
HM 30/560
HM 30/560
HM 30/560
HM 30/560
HM 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
MS 30/560
230/600 CAK/W33
231/600 CAK/W33
232/600 CAK/W33
240/600 CAK30/W33
241/600 CAK30/W33
600 630 258

375
475
330
440
272
389
489
356
466
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
Tr 670x6
46
60
63
40
40
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
11
11
11
9
9
89.5
140
188
101
136
AOH 30/630
AOH 31/630
AOH 32/630 G
AOH 240/630 G
AOH 241/630 G
HM 30/670
HM 31/670
HM 31/670
HM 31/670
HM 31/670
HMV 134
HMV 134
HMV 134
HMV 134
HMV 134
HM 30/600
HM 30/600
HM 30/600
HM 30/600
HM 30/600
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
MS 30/600-530
230/630 CAK/W33
231/630 CAK/W33
232/630 CAK/W33
240/630 CAK30/W33
241/630 CAK30/W33
630 670 280

395
500
348
452
294
409
514
374
478
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
Tr 710x7
50
59
62
40
40
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
12
12
12
12
12
127
189
252
140
185
AOH 30/670
AOHX 31/670
AOH 32/670 G
AOH 240/670 G
AOH 241/670
HM 30/710
HM 31/710
HM 31/710
HM 31/710
HM 31/710
HMV 142
HMV 142
HMV 142
HMV 142
HMV 142
HM 30/630
HM 30/630
HM 30/630
HM 30/630
HM 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
MS 30/630
230/670 CAK/W33
231/670 CAK/W33
232/670 CAK/W33
240/670 CAK30/W33
241/670 CAK30/W33
670 710 286

405
515
360
483
302
421
531
386
509
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
Tr 750x7
50
60
65
45
45
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
12
12
138
207
278
155
212
AOHX 30/710
AOHX 31/710
AOH 32/710 G
AOH 240/710 G
AOH 241/710
HM 30/750
HM 31/750
HM 31/750
HM 31/750
HM 31/750
HMV 150
HMV 150
HMV 150
HMV 150
HMV 150
HM 30/670
HM 30/670
HM 30/670
HM 30/670
HM 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
MS 30/670
230/710 CAK/W33
231/710 CAK/W33
232/710 CAK/W33
240/710 CAK30/W33
241/710 CAK30/W33
552
Withdrawal sleeves
d1 710 1000 mm
Type AOH
Dimensions
d1
Mass
B1
1)
B2
G1 G2
mm
Designations
Withdrawal
sleeve
in
mm kg
Appropriate
nut for
dismounting
Hydraulic
nut
Lock
nut
Locking
washer
Bearing(s)
710 750 300

425
540
380
520
316
441
556
408
548
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
Tr 800x7
50
60
65
45
45
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
12
12
159
238
320
178
248
AOH 30/750
AOH 31/750
AOH 32/750
AOH 240/750 G
AOH 241/750 G
HM 30/800
HM 31/800
HM 31/800
HM 31/800
HM 31/800
HMV 160
HMV 160
HMV 160
HMV 160
HMV 160
HM 30/710
HM 30/710
HM 30/710
HM 30/710
HM 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
MS 30/710
230/750 CAK/W33
231/750 CAK/W33
232/750 CAK/W33
240/750 CAK30/W33
241/750 CAK30/W33
750 800 308

438
550
395
525
326
456
568
423
553
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
Tr 850x7
50
63
67
50
50
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
15
204
305
401
237
318
AOH 30/800
AOH 31/800
AOH 32/800
AOH 240/800 G
AOH 241/800 G
HM 30/850
HM 31/850
HM 31/850
HM 31/850
HM 31/850
HMV 170
HMV 170
HMV 170
HMV 170
HMV 170
HM 30/750
HM 30/750
HM 30/750
HM 30/750
HM 30/750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
230/800 CAK/W33
231/800 CAK/W33
232/800 CAK/W33
240/800 CAK30/W33
241/800 CAK30/W33
800 850 325

462
585
415
560
343
480
603
445
600
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
Tr 900x7
53
62
70
50
60
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
15
230
345
461
265
368
AOH 30/850
AOH 31/850
AOH 32/850
AOH 240/850 G
AOH 241/850
HM 30/900
HM 31/900
HM 31/900
HM 31/900
HM 31/900
HMV 180
HMV 180
HMV 180
HMV 180
HMV 180
HM 30/800
HM 30/800
HM 30/800
HM 30/800
HM 30/800
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
MS 30/800-750
230/850 CAK/W33
231/850 CAK/W33
232/850 CAK/W33
240/850 CAK30/W33
241/850 CAK30/W33
850 900 335

475
585
430
575
355
495
605
475
620
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
Tr 950x8
55
63
70
55
60
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
15
253
379
489
296
402
AOH 30/900
AOH 31/900
AOH 32/900
AOH 240/900
AOH 241/900
HM 30/950
HM 31/950
HM 31/950
HM 31/950
HM 31/950
HMV 190
HMV 190
HMV 190
HMV 190
HMV 190
HM 30/850
HM 30/850
HM 30/850
HM 30/850
HM 30/850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
230/900 CAK/W33
231/900 CAK/W33
232/900 CAK/W33
240/900 CAK30/W33
241/900 CAK30/W33
900 950 355

500
600
467
605
375
520
620
512
650
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
Tr 1000x8
55
62
70
55
60
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
15
285
426
533
340
449
AOH 30/950
AOH 31/950
AOH 32/950
AOH 240/950
AOH 241/950
HM 30/1000
HM 31/1000
HM 31/1000
HM 31/1000
HM 31/1000
HMV 200
HMV 200
HMV 200
HMV 200
HMV 200
HM 30/900
HM 30/900
HM 30/900
HM 30/900
HM 30/900
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
MS 30/900-850
230/950 CAK/W33
231/950 CAK/W33
232/950 CAK/W33
240/950 CAK30/W33
241/950 CAK30/W33
950 1 000 365

525
630
469
645
387
547
652
519
695
Tr 1060x8
Tr 1060x8
Tr 1060x8
Tr 1060x8
Tr 1060x8
57
63
70
57
65
G 1/4
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
15
318
485
608
369
519
AOH 30/1000
AOH 31/1000
AOH 32/1000
AOH 240/1000
AOH 241/1000
HM 30/1060
HM 31/1060
HM 31/1060
HM 31/1060
HM 31/1060
HMV 212
HMV 212
HMV 212
HMV 212
HMV 212
HM 30/950
HM 30/950
HM 30/950
HM 30/950
HM 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
MS 30/950
230/1000 CAK/W33
231/1000 CAK/W33
232/1000 CAK/W33
240/1000 CAK30/W33
241/1000 CAK30/W33
1 000 1 060 385

540
498
665
407
562
548
715
Tr 1120x8
Tr 1120x8
Tr 1120x8
Tr 1120x8
60
65
60
65
G 1/4
G 1/4
G 1/4
G 1/4
15
15
15
15
406
599
479
652
AOH 30/1060
AOH 31/1060
AOH 240/1060
AOH 241/1060
HM 30/1120
HM 30/1120
HM 30/1120
HM 30/1120
HMV 224
HMV 224
HMV 224
HMV 224
HM 30/1000
HM 30/1000
HM 30/1000
HM 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
MS 30/1000
230/1060 CAK/W33
231/1060 CAK/W33
240/1060 CAK30/W33
240/1060 CAK30 W33
553

Lock nuts
M 10x0.75 M 115x2
Dimensions
G
d1
d3
mm
Axial
load
carrying
capacity
static
Mass
Designations
Lock
nut
kN
kg
Appropriate
locking
washer
Hook/impact
spanner
M 10x0.75
13.5
18
9.8
0.006
KM 0
MB 0
M 12x1
17
22
11.8
0.008
KM 1
MB 1
HN 1
M 15x1
21
25
14.6
0.012
KM 2
MB 2
HN 2
M 17x1
24
28
19.6
0.012
KM 3
MB 3
HN 3
M 20x1
26
32
24
0.02
KM 4
MB 4
HN 4
M 25x1.5
32
38
31.5
0.028
KM 5
MB 5
HN 5
M 30x1.5
38
45
36.5
0.038
KM 6
MB 6
HN 6
M 35x1.5
44
52
50
0.058
KM 7
MB 7
HN 7
M 40x1.5
50
58
2.5
62
0.078
KM 8
MB 8
HN 8
M 45x1.5
56
65
10
2.5
78
0.11
KM 9
MB 9
HN 9
M 50x1.5
61
70
11
2.5
91.5
0.14
KM 10
MB 10
HN 10
M 55x2
67
75
11
91.5
0.15
KM 11
MB 11
HN 11
M 60x2
73
80
11
95
0.16
KM 12
MB 12
HN 12
M 65x2
79
85
12
108
0.19
KM 13
MB 13
HN 13
M 70x2
85
92
12
3.5
118
0.22
KM 14
MB 14
HN 14
M 75x2
90
98
13
3.5
134
0.27
KM 15
MB 15
HN 15
M 80x2
95
105
15
3.5
173
0.36
KM 16
MB 16
HN 16
M 85x2
102
110
16
3.5
190
0.42
KM 17
MB 17
HN 17
M 90x2
108
120
16
10
216
0.51
KM 18
MB 18
HN 18
M 95x2
113
125
17
10
236
0.58
KM 19
MB 19
HN 19
M 100x2
120
130
18
10
255
0.68
KM 20
MB 20
HN 20
M 105x2
126
140
18
12
290
0.81
KM 21
MB 21
HN 21
M 110x2
133
145
19
12
310
0.89
KM 22
MB 22
HN 22
M 115x2
137
150
19
12
315
0.91
KM 23
MB 23
718909
554
Lock nuts
M 120x2 M 200x3
Dimensions
G
d1
d3
mm
Axial
load
carrying
capacity
static
Mass
Designations
Lock
nut
kN
kg
Appropriate
locking
washer
Hook/impact
spanner
M 120x2
135
138
145
155
20
20
12
12
5
5
265
340
0.69
0.98
KML 24
KM 24
MBL 24
MB 24
718909
718909
M 125x2
148
160
21
12
360
1.1
KM 25
MB 25
718909
M 130x2
145
149
155
165
21
21
12
12
5
5
285
365
0.84
1.2
KML 26
KM 26
MBL 26
MB 26
718909
718909
M 135x2
160
175
22
14
430
1.4
KM 27
MB 27
718909
M 140x2
155
160
165
180
22
22
12
14
5
6
305
430
0.92
1.4
KML 28
KM 28
MBL 28
MB 28
718909
718909
M 145x2
171
190
24
14
520
1.85
KM 29
MB 29
718909
M 150x2
170
171
180
195
24
24
14
14
5
6
390
530
1.3
1.85
KML 30
KM 30
MBL 30
MB 30
718909
718909, 718910
M 155x3
182
200
25
16
540
2.05
KM 31
MB 31
718910
M 160x3
180
182
190
210
25
25
14
16
5
7
405
585
1.4
2.25
KML 32
KM 32
MBL 32
MB 32
718909
718910
M 165x3
193
210
26
16
570
2.3
KM 33
MB 33
718910
M 170x3
190
193
200
220
26
26
16
16
5
7
430
620
1.6
2.55
KML 34
KM 34
MBL 34
MB 34
718910
718910
M 180x3
200
203
210
230
27
27
16
18
5
8
450
670
1.8
2.7
KML 36
KM 36
MBL 36
MB 36
718910
718910
M 190x3
210
214
220
240
28
28
16
18
5
8
475
695
1.9
3
KML 38
KM 38
MBL 38
MB 38
718910
718910
M 200x3
222
226
240
250
29
29
18
18
8
8
625
735
2.6
3.3
KML 40
KM 40
MBL 40
MB 40
718910
718910, 718911
555

Lock nuts/removal nuts
Tr 210x4 Tr 280x4
Dimensions
G
Mass
d1
d3
Designations
Lock
nut
mm
kg
Appropriate
locking
washer
Impact
spanner
Tr 210x4
238
270
30
20
10
5.1
HM 42 T
718911
Tr 220x4
250
280
32
20
10
4.75
HM 44 T
MB 44
718911
Tr 230x4
260
290
34
20
10
5.45
HM 46 T
718911
Tr 240x4
270
300
34
20
10
5.6
HM 48 T
MB 48
718911
Tr 250x4
290
320
36
20
10
7.45
HM 50 T
718911
Tr 260x4
300
330
36
24
12
7.55
HM 52 T
MB 52
718912
Tr 280x4
320
350
38
24
12
8.65
HM 56 T
MB 56
718912
556
Lock nuts with locking clip

Tr 220x4 Tr 530x6
Dimensions
G
Mass
d1
d2
d3
B1
M1 M2
mm
Designations
Lock nut +
locking clip
and screw
(DIN 933)
kg
Hexagonheaded
screw
Appropriate
impact
spanner
Tr 220x4
242
229
260
30
41
20
12
13.5
2.75
HM 3044 + MS 3044
M 6x12
718911
Tr 240x4
270
253
290
34
46
20
10
12
17.5
4.5
HM 3048 + MS 3052-48
M 8x16
718911
Tr 260x4
290
273
310
34
46
20
10
12
17.5
4.8
HM 3052 + MS 3052-48
M 8x16
718911
Tr 280x4
310
293
330
38
50
24
10
12
17.5
5.75
HM 3056 + MS 3056
M 8x16
718912
Tr 300x4
336
340
316
326
360
380
42
40
54
53
24
24
12
12
12
12
4
4
20.5
30.5
8.35
11.5
HM 3060 + MS 3060
HM 3160 + MS 3160
M 8x16
M 10x20
718912
718912
Tr 320x5
356
360
336
346
380
400
42
42
55
56
24
24
12
12
15
15
5
5
21
31
9
13
HM 3064 + MS 3068-64
HM 3164 + MS 3164
M 8x16
M 10x20
718912
7189121)
Tr 340x5
376
400
356
373
400
440
45
55
58
72
24
28
12
15
15
15
5
5
21
38
11
24
HM 3068 + MS 3068-64
HM 3168 + MS 3172-68
M 8x16
M 12x25
7189121)
718913
Tr 360x5
394
420
375
393
420
460
45
58
58
75
28
28
13
15
15
15
5
5
20
38
11.5
26.5
HM 3072 + MS 3072
HM 3172 + MS 3172-68
M 8x16
M 12x25
718913
718913
Tr 380x5
422
440
399
415
450
490
48
60
62
77
28
32
14
18
15
15
5
5
24
40
15
32
HM 3076 + MS 3080-76
HM 3176 + MS 3176
M 10x20
M 12x25
718913
718913
Tr 400x5
442
460
419
440
470
520
52
62
66
82
28
32
14
18
15
15
5
5
24
45
17
38
HM 3080 + MS 3080-76
HM 3180 + MS 3184-80
M 10x20
M 16x30
718913
718913
Tr 420x5
462
490
439
460
490
540
52
70
66
90
32
32
14
18
15
15
5
5
24
45
18.5
45
HM 3084 + MS 3084
HM 3184 + MS 3184-80
M 10x20
M 16x30
718913
718914
Tr 440x5
490
510
463
478
520
560
60
70
77
90
32
36
15
20
15
15
5
5
28
43
26
46.5
HM 3088 + MS 3092-88
HM 3188 + MS 3192-88
M 12x25
M 16x30
718913
718914
Tr 460x5
510
540
483
498
540
580
60
75
77
95
32
36
15
20
15
15
5
5
28
43
27
50.5
HM 3092 + MS 3092-88
HM 3192 + MS 3192-88
M 12x25
M 16x30
718914
718914
Tr 480x5
530
560
503
528
560
620
60
75
77
95
36
36
15
20
15
15
5
5
28
53
28
62
HM 3096 + MS 30/500-96
HM 3196 + MS 3196
M 12x25
M 16x30
718914
718914
Tr 500x5
550
580
523
540
580
630
68
80
85
100
36
40
15
23
15
15
5
5
28
45
33.5
63.5
HM 30/500 + MS 30/500-96
HM 31/500 + MS 31/500
M 12x25
M 16x30
718914
718914
Tr 530x6
590
610
558
575
630
670
68
80
90
105
40
40
20
23
21
21
7
7
34
51
42.5
71.5
HM 30/530 + MS 30/600-530
HM 31/530 + MS 31/530
M 16x30
M 20x40
718915
718915
1) Impact spanner 718913 also suitable
557

Lock nuts with locking clip
Tr 560x6 Tr 1120x8
Dimensions
G
Mass
d1
d2
d3
B1
M1 M2
mm
Designations
Lock nut +
locking clip
and screw
(DIN 933)
kg
Hexagonheaded
screw
Appropriate
impact
spanner
Tr 560x6
610
650
583
608
650
710
75
85
97
110
40
45
20
25
21
21
7
7
29
54
44.5
86.5
HM 30/560 + MS 30/560
HM 31/560 + MS 31/600-560
M 16x30
M 20x40
718915
718915
Tr 600x6
660
690
628
648
700
750
75
85
97
110
40
45
20
25
21
21
7
7
34
54
52.5
91.5
HM 30/600 + MS 30/600-530
HM 31/600 + MS 31/600-560
M 16x30
M 20x40
718915
718915
Tr 630x6
690
730
658
685
730
800
75
95
97
120
45
50
20
28
21
21
7
7
34
61
55 0
125
HM 30/630 + MS 30/630
HM 31/630 + MS 31/630
M 16x30
M 20x40
718915
718916
Tr 670x6
740
775
703
730
780
850
80
106
102
131
45
50
20
28
21
21
7
7
39
66
68.5
155
HM 30/670 + MS 30/670
HM 31/670 + MS 31/670
M 16x30
M 20x40
718916
718916
Tr 710x7
780
825
742
772
830
900
90
106
112
133
50
55
25
30
21
21
7
7
39
69
91.5
162
HM 30/710 + MS 30/710
HM 31/710 + MS 31/710
M 16x30
M 24x50
718916
718916
Tr 750x7
820
875
782
813
870
950
90
112
112
139
55
60
25
34
21
21
7
7
39
70
940
190
HM 30/750 + MS 30/800-750
HM 31/750 + MS 31/800-750
M 16x30
M 24x50
718916
718916
Tr 800x7
870
925
832
863
920
1 000
90
112
112
139
55
60
25
34
21
21
7
7
39
70
99.5
202
HM 30/800 + MS 30/800-750
HM 31/800 + MS 31/800-750
M 16x30
M 24x50
718916
-
Tr 850x7
925
975
887
914
980
1 060
90
118
115
145
60
70
25
38
21
21
7
7
44
71
115
234
HM 30/850 + MS 30/900-850
HM 31/850 + MS 31/850
M 20x40
M 24x50
Tr 900x7
975
1 030
937
969
1 030
1 120
100
125
125
154
60
70
25
38
21
21
7
7
44
76
131
279
HM 30/900 + MS 30/900-850
HM 31/900 + MS 31/900
M 20x40
M 24x50
Tr 950x8
1 025
1 080
985
1 017
1 080
1 170
100
125
125
154
60
70
25
38
21
21
7
7
46
78
139
293
HM 30/950 + MS 30/950
HM 31/950 + MS 31/950
M 20x40
M 24x50
Tr 1000x8
1 085
1 140
1 040
1 077
1 140
1 240
100
125
125
154
60
70
25
38
21
21
7
7
51
88
157
336
HM 30/1000 + MS 30/1000
HM 31/1000 + MS 31/1000
M 20x40
M 24x50
Tr 1060x8
1 145
1 210
1 100
1 137
1 200
1 300
100
125
125
154
60
70
25
38
21
21
7
7
51
88
166
354
HM 30/1060 + MS 30/1000
HM 31/1060 + MS 31/1000
M 20x40
M 24x50
Tr 1120x8
1 205
1 160
1 260
100
125
60
25
21
51
175
HM 30/1120 + MS 30/1000
M 20x40
558
Locking washers
d 10 280 mm
Dimensions
d1
Mass
d2
Designation
mm
Dimensions
d
g
mm
d1
d2
Mass
Designation
10
13.5
21
8.5
MB 0
115
137
159
12
110.5
107
MB 23
12
17
25
10.5
MB 1
120
135
138
152
164
2
2
14
14
115
115
70
108
MBL 24
MB 24
15
21
28
13.5
MB 2
125
148
170
14
120
115
MB 25
17
24
32
15.5
MB 3
130
20
26
36
18.5
MB 4
145
149
161
175
2
2
14
14
125
125
80
115
MBL 26
MB 26
25
32
42
1.25
23
MB 57
135
160
185
14
130
140
MB 27
30
38
49
1.25
27.5
MB 6
140
155
160
172
192
2
2
16
16
135
135
90
135
MBL 28
MB 28
35
44
57
1.25
32.5
11
MB 7
145
172
202
16
140
165
MB 29
40
50
62
1.25
37.5
13
MB 8
150
45
56
69
1.25
42.5
15
MB 9
170
171
189
205
2
2
16
16
145
145
100
180
MBL 30
MB 30
50
61
74
1.25
47.5
16
MB 10
155
182
212
2.5
16
147.5
200
MB 31
55
67
81
1.5
52.5
22
MB 11
160
180
182
199
217
2.5
2.5
18
18
154
154
140
215
MBL 32
MB 32
60
73
86
1.5
57.5
24
MB 12
165
193
222
2.5
18
157.5
240
MB 33
65
79
92
1.5
62.5
30
MB 13
170
70
85
98
1.5
66.5
32
MB 14
190
193
211
232
2.5
2.5
18
18
164
164
150
240
MBL 34
MB 34
75
90
104
1.5
71.5
35
MB 15
180
200
203
222
242
2.5
2.5
20
20
174
174
160
260
MBL 36
ML 36
80
95
112
1.75
10
76.5
46
MB 16
190
85
102
119
1.75
10
81.5
53
MB 17
210
214
232
252
2.5
2.5
20
20
184
184
170
260
MBL 38
MB 38
90
108
126
1.75
10
86.5
61
MB 18
200
222
226
245
262
2.5
2.5
20
20
194
194
220
280
MBL 40
MB 40
95
113
133
1.75
10
91.5
66
MB 19
220
250
292
24
213
350
MB 44
100
120
142
1.75
12
96.5
77
MB 20
240
270
312
24
233
450
MB 48
105
126
145
1.75
12
100.5
83
MB 21
260
300
342
28
253
650
MB 52
110
133
154
1.75
12
105.5
91
MB 22
280
320
362
28
273
1 050
MB 56
559

Locking washers type MB . . A
d 12 100 mm
Dimensions
d1
Mass
d2
Designation
mm
d
g
12
17
25
1.2
10.5
2.5
MB 1 A
15
21
28
1.2
13.5
3.5
MB 2 A
17
24
32
1.2
15.5
3.5
MB 3 A
20
26
36
1.2
18.5
MB 4 A
25
32
42
1.8
23
8.5
MB 5 A
30
38
49
1.8
27.5
11
MB 6 A
35
44
57
1.8
32.5
15.5
MB 7 A
40
50
62
1.8
37.5
18
MB 8 A
45
56
69
1.8
42.5
21
MB 9 A
50
61
74
1.8
47.5
22.5
MB 10 A
55
67
81
2.5
52.5
36.5
MB 11 A
60
73
86
2.5
57.5
40
MB 12 A
65
79
92
2.5
62.5
50
MB 13 A
70
85
98
2.5
66.5
53
MB 14 A
75
90
104
2.5
71.5
58
MB 15 A
80
95
112
2.5
10
76.5
66
MB 16 A
85
102
119
2.5
10
81.5
76
MB 17 A
90
108
126
2.5
10
86.5
87
MB 18 A
95
113
133
2.5
10
91.5
94
MB 19 A
100
120
142
2.5
12
96.5
110
MB 20 A
560
Dimensions
mm
d1
d2
Mass
Designation
Maintenance products
SKF develops and markets maintenance tools,

lubricants and lubricators to optimize mounting,
dismounting and lubrication of bearings. The
product assortment includes mechanical tools,
heaters, oil injection equipment, instruments,
lubricants and lubricators.
Mechanical tools
Mechanical tools are used mainly for mounting
and dismounting small and medium-sized bearings. The SKF range comprises tools for the
installation and removal of bearings and locking
devices. The range also contains bearing
handling tools for safe and rapid lifting and
positioning of bearings up to 500 kg.
Hook and impact spanners

SKF hook spanners have the exact radius to suit
the appropriate lock nut. This enables safe and
efficient tightening and minimizes the risk of
damage to both the nut and shaft.
Impact spanners are made of spheroidal
graphite cast iron and have a special impact
face to transmit a maximum torque to the nut.
Each spanner can be used with several nut
sizes.
Lock nut spanners and axial lock nut

sockets
To mount SKF self-aligning ball bearings on
adapter sleeves in housings, a special bearing
lock nut spanner set is available. Using these
spanners, the correct tightening angle is easy to
achieve and this enables consistently accurate
bearing mounting.
Axial lock nut sockets are especially useful if
there is insufficient space around the lock nut.
They have drive connections suitable for use
with power tools or torque wrenches.
Bearing fitting tools

SKF bearing fitting tools enable small bearings
to be cold mounted on a shaft. They can also
be used to mount bushings, seals and pulleys.
The kits consist of impact rings and sleeves and
a dead blow hammer.
Jaw pullers
SKF jaw pullers enable a wide range of bearings
to be dismounted. One of the puller series, designated TMMA, which design is unique to SKF,
incorporates a spring allowing easy opening and
closing of the arms, while a special safety solution helps to prevent dangerous overload. A
range of hydraulic spindles and rams are also
available for increased puller forces. The SKF
jaw puller range contains pullers with withdrawal forces up to 500 kN.
Strong back pullers

SKF strong back pullers are supplied as kits with
all necessary accessories to cover the most difficult pulling operations. Strong back pullers consist
of either a two or three-piece separable yoke,
which when placed behind the bearing makes a
strong back. The pulling force can be applied
using a mechanical spindle, a hydraulic spindle or
a hydraulic ram.
Internal and blind pullers

To dismount a wide range of deep groove ball
bearings from blind housing bores quickly and
easily, SKF has developed blind housing puller
kits. These pullers have hinged arms with specially
machined ends so that they fit into the bearing
raceway(s), allowing the bearing to be extracted
from the housing.
Puller kits for removing bearings from
housings, using an internal pull, consist of a
number of adjustable collets that can be expanded
to fit on the rear side of the bearing bore. A slide
hammer arrangement allows large forces to be
applied to the bearing in order to remove it.
For additional information on SKF maintenance
products, please visit www.mapro.skf.com or
order catalog 711-639.
Mechanical tools
Lock nut spanners
Bearing fitting tools
Jaw pullers
Strong back pullers
Internal and blind pullers

561
Other products
Hydraulic pumps and oil injectors

SKF hand-operated hydraulic pumps can develop pressures up to 21,750 psi (150 MPa). They
can be supplied with a highly accurate pressure
gauge, which allows the SKF Drive-up Method
to be employed. All pumps are contained in a
sturdy carrying case complete with a hose,
quick connection coupling, nipple and mounting
fluid.
Oil Injectors can supply oil pressures up to
58,000 psi (400 MPa). The SKF range comprises single injectors as well as a number of kits,
which contain an injector and a selection of the
most common accessories such as an adapter
block, high-pressure pipes and nipples.
For large bearings and applications requiring
a larger volume of oil, several air-driven
portable pumps and injectors providing pressures up to 43,000 psi (300 MPa) are available.
Hydraulic accessories
Hydraulic nut
Hydraulic nut
Hydraulic pump
Hydraulic pumps
Hydraulic accessories
Oil injection kit
Hydraulic tools
A variety of hydraulic tools is available to mount
and dismount bearings in a safe and controlled
manner. The SKF oil injection method enables
easy working while the SKF Drive-up Method
provides accurate results.
Hydraulic nuts
HMV .. E type hydraulic nuts enable mounting
and dismounting of bearings with tapered bores
of 50 mm and above. When compared with
mechanical methods, they considerably reduce
the time and effort needed to install or remove
a bearing. SKF HMV .. E nuts are available with
metric or imperial threads or with a plain bore.
SKF HMV .. E nuts, when used in conjunction
with SKF pumps fitted with a digital pressure
gauge and a dial indicator, allow the full
advantages of the SKF Drive-up Method to
be realized.
562
To facilitate connections between hydraulic tools

and most applications, SKF offers a wide range of
accessories including pressure gauges, high pressure pipes, connection nipples and mounting and
dismounting fluids.
Instruments
To realize maximum bearing life, it is important
to determine the operating condition of
machinery and their bearings. With the SKF
measuring instrument range, critical environmental conditions can be analyzed to achieve
optimum bearing performance.
Tachometers
Optical measurement is a safe and reliable
technique to determine rotational speed. Using
non-contact instruments is often essential to
meet industrial safety regulations. SKF provides
a range of highly accurate optical tachometers.
A range of accessories enables linear and direct
contact rotational speeds to be measured.
the indispensable ThermoPen up to a highly

accurate, advanced dual channel, wide range
thermometer. A comprehensive range of temperature probes for a variety of applications is
also available.
Electronic stethoscope
The noise of a machine can help indicate troublesome parts such as damaged bearings, valve
chatter, tappet noise, piston slap and gear and
pump noise. The SKF electronic stethoscope is a
hand-held instrument that picks up the noise or
vibration from a machine via a probe and helps
the user locate the source of the noise.
Oil check monitor
Alignment instruments and shims

SKF has developed laser alignment tools
to make the machinery alignment process faster,
easier and more reliable. Using the latest laser
technology, the SKF shaft alignment tool measures both the parallel and angular alignment of
shafts to be connected.
SKFs belt alignment tool aligns the grooves in a
pulley rather than the pulley face, facilitating accurate and simultaneous adjustment of belt tension
and pulley alignment.
A comprehensive range of pre-cut machinery
shims in both metric and inch dimensions is available as well as stainless steel double slot shims
for use with many housings.
The temperature of a bearing or bearing housing is a quick and easy indication of the running
conditions of the bearing. SKF provides a range
of contact and non-contact thermometers from
The SKF oil check monitor determines oil condition by analyzing the contamination levels and
electro-chemical changes in both mineral and
synthetic based oils. It was developed originally
for engine oils but is suitable for gear and lubrication oils. It can also help to detect water, antifreeze or metallic particles in an oil sample.

Laser tachometer
Thermometer
Electronic stethoscope
Oil check Monitor
Shaft alignment tool TMEA2
Belt alignment tool TMEB2
Thermometers
563
Other products
Bearing heaters
A fast and very efficient way to heat a bearing
for mounting is to use an induction heater.
These heaters, which only heat metallic components, control bearing temperature safely and
accurately, to minimize the risk of bearing damage caused by excessive heat.
Induction heaters
SKF pioneered the use of induction heaters for
bearing applications. SKF TIH induction heaters
cover a wide range of bearing types and sizes.
The smaller heaters are recommended for
bearings weighing up to 170 lb (80 kg) while
the largest floor model can be used for bearings
up to 1,500 lb (700 kg).
Large heaters are also suitable for heating
smaller bearings, as a power reduction feature
is incorporated. SKF induction heaters can be
controlled by means of time or temperature. In
addition, they feature a bearing heating mode
to help prevent damage to bearings through
over-heating. At the end of each heating cycle,
the bearings are automatically demagnetized.
Portable induction heater
Heating devices to remove inner rings
The portable SKF induction heater heats bearings and other components with a bore diameter
up to 4 in. (100 mm) and a maximum weight of
11 lb (5 kg). It uses a patented method of heating based on high frequency induction for optimized efficiency. This truly portable unit weighs
just 10 lb (4.5 kg) and is supplied with a heating
clamp, temperature probe, power cable and a
carrying case.
A range of special heating devices for removing

cylindrical roller bearing inner rings from shafts
is available from SKF. Aluminum heating rings
are designed for dismounting inner rings of small
and medium-size cylindrical roller bearings.
Adjustable induction heaters are also available
for frequent dismounting of various sizes of
cylindrical roller bearing inner rings. Two sizes
are available covering raceway diameters from
80 to 170 mm. Non-adjustable induction heaters
are designed to suit a particular bearing and
application. They are normally used to dismount
inner rings of multi-row cylindrical roller
bearings.
Hot plate
The SKF electric hot plate heats small bearings
and other machinery components. It is suitable
for bearings with an outside diameter up to
approximately 170 mm or with a weight up to 4
kg. A lid for retaining the heat also prevents dirt
from entering the bearing.
Gloves
SKF heat resistant gloves are specially designed
for the handling of heated bearings and other
machine components.
Induction heater TIH 100
Induction heater TIH 220
Portable induction heater
Hot plate
Adjustable induction heaters
Non-adjustable induction heater
564
Lubrication products
Lubricants and lubricators
Grease guns and pumps
SYSTEM MultiPoint automatic lubricator
The value and importance of using the right

lubricant is explained in the section Lubrication, starting on page 23. The formulation of
all SKF bearing greases is based on extensive
research, grease performance testing and field
experience.
SKF developed many of the internationally
accepted bearing-related grease testing parameters. For correct lubricant application,
a range of lubrication equipment is available
from SKF.
The SKF range also includes grease guns, manual and air-driven grease pumps and grease
filler pumps. Grease filler pumps are used to fill
grease guns and grease packers from standard
SKF grease drums.
Grease meter
SKF SYSTEM MultiPoint is a microprocessor

controlled automatic lubricator. Grease can be
supplied to up to eight points, using standard
SKF grease cartridges. The cartridges assure
the user that only clean fresh grease is used.
SYSTEM MultiPoint lubricator has been tested
and approved for use with all SKF bearing
greases.
Greases
The SKF grease meter can accurately measure

the volume of grease pumped into a bearing. A
wide range of accessories is available.
SYSTEM 24 single point automatic

lubricator
Oil leveller
The SKF oil levellers are designed for automatic
adjustment of the optimal oil level in oil bath
lubricated applications. They effectively solve
the problem of adjusting the correct oil level
during operation or due to leakage rather than
just during standstill.
SKF offers a range of high quality lubricating

greases to suit many bearing applications and
conditions. The greases have been developed
specifically to meet the needs of rolling bearings
and their application conditions. A guide to
select the most suitable SKF grease can be
found in table x on pages 246 and 247. The
table also contains the important properties.
SKF SYSTEM 24 is a single point automatic

lubricator, pre-filled with SKF grease or oil.
Compared with traditional manual relubrication
techniques, SKF SYSTEM 24 provides a more
accurate control of the quantity of lubricant
supplied. It can be set to continuously supply
the correct amount of quality lubricant over a
given time period, up to a maximum of one
year.
Greases
Grease guns and pumps
Grease meter
System 24
System MultiPoint
Oil leveler
For additional information on SKF lubrication

products, please oder catalog 750-900.
565
Other products
Lubrication products
Centralized lubrication
systems
Circulating oil lubrication systems

Total-loss centralized lubrication
systems
In circulating oil lubrication systems the oil is

supplied to the lubrication points with the aid of
pumps. After passing the lubrication point the
lubricant returns to a tank or sump where it is
filtered before being returned to the lubrication
points. Generally a larger quantity of oil is supplied to the lubrication points than actually
needed.
For circulating oil lubrication systems a
variety of components are available enabling
tailor made solutions for all types of industrial
applications. A continuous flow of oil produced
by a pump and then divided up is required for
machines or installations that use large
amounts of oil for lubricating and cooling
purposes.
The lubricant for the lubrication points is
apportioned by progressive feeders, flow
limiters, flow controllers and/or flow meters.
Components, assemblies and complete systems

for the lubrication technology are also part of
the SKF business. The competent SKF company
for these products is the Willy Vogel AG, the
world leader in the field of centralized lubrication systems for machines and industrial, commercial or rail bound vehicles. The product
range of lubrication and circulating oil systems
essentially includes the following products briefly
described.
Detailed information can be found in the
Vogel brochure Overview of Products for
Industry: Centralized lubrication and minimal
quantity lubrication for machinery and systems.
For additional information please visit
www.skfusa.com and click on Products and
look for Engineered lubrication systems.
Generally there are two types of centralized
lubrication systems: total-loss lubrication systems and circulating lubrication systems.
Centralized lubrication systems feed a small and

always fresh amount of lubricant to each lubrication point at requisite intervals, in line with a
predetermined need. The residual lubricant that
escapes from the lubrication point at some time
is disposed of (in case of industrial applications)
or is lost (in case of commercial or rail bound
vehicles).
Depending on the operating conditions totalloss centralized lubrication systems can be
designed as
Total-loss centralized systems
Circulating oil lubrication systems
Multi-circuit circulating oil systems
Chain lubrication systems
Oil and air lubrication system
Minimal quantity lubrication system
566
single-line systems
dual-line systems
multi-line systems
equipped with components individually needed.
The applicable lubricants range from oils with a
viscosity of 2 to 16 000 mm2/s and fluid greases with an NLGI consistency class of 0, 00 and
000 to consistent greases with an NLGI consistency class of 1, 2 and 3.
Multi-circuit circulating oil systems

Vogel multi-circuit circulating oil supply systems
are custom-designed and suitable for all types
of hydrostatic shoe bearing arrangements that
carry large rotating drums. They are modern
systems, use state-of-the-art components
and enable stable pressure at each individual
bearing point.
Lubrication products/Seals
Chain lubrication systems

Vogel chain lubrication systems are customized,
fully automatic systems for lubrication of drive
or conveyor chains in all types of industrial
applications. They enable environmental
friendly systems that deliver precisely metered
quantities of lubricant while the machine is in
operation.
Oil+air lubrication systems

Modern oil+air lubrication systems are mainly
used to supply extremely small amounts of oil
to bearing arrangements, e.g. in spindles of
machine tools or in linear guidance systems.
They deliver a precise metered quantity of
lubricant to each bearing to improve the operating reliability and reduce the consumption.
Splash and spray systems

These systems are manufactured on demand
and custom-made to fulfill the needs of a
specific application. They are typically used in
customized handling equipment, for example,
to spray lubricants onto conveyor belts or to
spray billets and stampings with oil.
Minimal quantity lubrication systems

Minimal quantity lubrication is the clean alternative to wet machining and an optimal way to
supplement dry machining. It can be used to
optimize machining processes like milling,
rolling, high speed cutting, drilling, boring or
tapping. The oil or emulsion supplied to the
working surface gets lost and no residue is left.
These minimal quantity lubrication systems,
which carry the trademark LubriLean, provide
considerable technology advantages. In addition,
these systems can be used to reduce costs and
increase productivity.
For additional information on SKF lubrication
products, please oder catalog 750-900.
Seals
Separator filter dryer
Seals represent an important part of the SKF

business. The SKF range consists of seals in
contact with stationary or sliding surfaces and
covers virtually all application requirements. Not
just simple sealing arrangements, but a wide
range of seals for demanding industrial applications. From design concepts to high volume
production, from original equipment to aftermarket, SKF can provide sealing solutions to its
customers.
Detailed information can be found in the catalogues Industrial seals and Hydraulic seals.
The standard range of dynamic SKF seals for
rotating machine components is also listed in
the SKF Interactive Engineering Catalogue.
Moisture, oil and dirt hurt compressed

air systems
Seals for rotating machine components

Radial shaft seals
Mechanical seals
V-ring seals
Axial clamp seals
Wear sleeves for shaft repairs
Seals for reciprocating components

Hydraulic piston seals
Hydraulic rod seals
Wiper seals
Guide rings and guide strips
Seals for stationary surfaces

O-rings
Back-up rings
PTFE seals for different purposes

Piston and rod seals
Wiper seals
Guide strips
Radial shaft seals
PTFE encapsulated O-rings
From concrete plants to food processing, countless applications relying on compressed air systems will eventually develop water vapor, oil, or
particulates in the air lines. These contaminants
damage delicate pneumatic controls, shorten
machine life, and reduce productivity. Moisture
alone is the main cause of most pneumatic
equipment failures.
Oil, water, or particulates in compressed air
contribute to increased maintenance, higher
operating costs, and lower productivity. Many
plants have found options to control compressed air contamination are often unreliable,
cost-prohibitive, or maintenance-intense.
SKF Separator Filter Dryer delivers

clean, dry air supply
SKF developed the ultimate solution for clean
compressed air: the Separator Filter Dryer
(SFD), an innovative, three-in-one dryer system
that keeps compressed air free of water,
contaminants, and oil.
Compact and easy to install, the SFD dries
compressed air right from a compressors
reservoir tank or at a point of use, eliminating
the need for additional external filters.
The SFD dual-cartridge design channels air
flow through one desiccant cartridge while the
other regenerates, typically using less than 10%
of air for regeneration.
SFD eases maintenance, protects profits

Accessible valves, spin-on desiccant cartridges
and a patented filtration system contribute to
easy, cost-effective preventive maintenance.
Reliable SKF air dryer technology is proven in
harsh environments across many industries,
including ours SFD units currently operate in
SKF production facilities worldwide.
For additional information order publication
#170-450A.
Separator filter dryer

567
Other products
Reliability and services
SKF has been a leader and innovator in bearing

technology since 1907. The evolution of SKF
expertise in machine reliability stems from the
very nature of bearings and their applications.
SKFs understanding of a bearings performance
in an application requires an equally extensive
knowledge of the machines and the processes.
The thorough understanding of machine components, systems and related processes,
enables SKF to create and provide realistic
solutions for optimum machine and process
reliability and productivity.
Close working partnerships with customers
worldwide has provided SKF with an extensive
knowledge of applications in virtually every
industry. As a result, SKF has learned to apply
the most relevant of todays emerging technologies to industry-specific applications.
Through SKF Reliability Systems, SKF provides a single source for a complete productivity
solution. The goal is to help customers reduce
total machine related costs, enhance productivity and strengthen profitability. Whatever the
requirements, SKF Reliability Systems offers the
knowledge, services and products needed to
achieve specific business goals.
An integrated platform
SKFs range of products and services provides
the solutions that will ultimately lead to
increased bottom line profitability. The focus on
technology and seamless interface with
plantwide systems supports four key areas.
SKF can assist customers in retention, storage

and utilization of crucial information with its
@ptitude industrial decision support software
(page 569).
Condition monitoring
As a leading supplier of condition monitoring
products, SKF offers a complete range from
hand-held data collectors/analyzers to online
surveillance and machine protection systems.
These products provide interface with condition
monitoring analysis software and other
plantwide systems and are listed starting on
page 570.
Tools and lubricants
Diagram 1
Optimum efficiency
Operator driven reliability
Proactive reliability maintenance
Predictive maintenance
Preventive maintenance
Minimum efficiency
568
Component innovations are needed to achieve

productivity goals that were never intended by
original equipment manufacturers. SKF has
developed bearing products designed to run
faster, longer and cooler without maintenance in
many difficult applications.
Decision support
SKF has developed a range of maintenance

tools and lubricants to provide safe and
damage-free machine maintenance. Brief
information on these products is given in the
section Maintenance products starting on
page 561 and Lubrication products, starting
on page 565.
Reactive / corrective
Component innovations
Asset management is failure

modes and effects analysis-based
Online performance intelligence
and correction
Designed for reliability
Operator involvement and
commitment
Efficiency: > 80 %
4.5 6 s
Monitor
Condition-based
Data analysis
Efficiency: 60 80 %
3.5 4.5 s
Clean and inspect
Time based
Equipment data available
Efficiency: 40 60 %
2.5 3.5 s
Run to failure
Repair/replace
Limited data
Efficiency: < 40 %
2 2.5 s
The assist efficiency

optimization concept
The Asset Efficiency OptimizationTM (AEO) concept from SKF picks up where most plan asset
management programs typically stop. Using this
concept enables a plant to produce the same
amount for less cost, or to produce more for
the same costs. It is a system for organizing
and applying assets from personnel to
machinery bringing together knowledge and
technology to achieve the greatest return on
investment.
By applying the power of SKFs technology
and service solutions, you can benefit from a
program that assists in achieving your
organizations overall business objectives. These
include reduced costs, greater productivity,
better utilization of resources, and as a result,
increased bottom line profitability (diagram 1).
SKF technology and

service solutions
The following summarizes the most important
services and products that SKF Reliability
Systems offers to provide solutions to the reallife application conditions. For detailed information on the SKF Reliability Systems program
please refer to publication 5160 E The Guide
to Asset Efficiency OptimizationTM for Improved
Profitability or visit www.skfreliability.com to
see the latest information on strategies and
services.
Assessment
An assessment can include one or all of the
following areas.
Determination of current situation

Maintenance
Supply and stores processes
Predictive maintenance
Reliability and services
Machine maintenance
Maintenance strategy
SKF can help to establish a comprehensive
maintenance strategy, designed to make sure
that productivity as well as safety and integrity
issues receive the attention they require.
Diagram 1 on page 568 illustrates the range
and ranking of maintenance practices.
The latest and innovative approach to
maintenance is called Operator Driven Reliability
(ODR). This maintenance concept is simply a
framework for organizing the activities of plant
operations personnel in concert with a companys reliability maintenance practices. SKF has
the knowledge and equipment to initiate and
support this approach.
Maintenance engineering
Maintenance engineering is putting the strategy
to work and includes for example the implementation of a Computerized Maintenance
Management System (CMMS) with all the data
and process information needed to achieve
maintenance strategy goals.
Supply process
This service is an integral part of increasing
profitability by reducing transaction costs,
releasing capital tied up in spare inventory and
making sure that the spares are available when
needed.
SKF Reliability Systems has developed its most

comprehensive service program for rotating
equipment to drive machine maintenance in the
most cost effective ways. This program includes
products and services such as
Machine alignment
Precision balancing
Lubrication management
Bearing analysis
Technology advice and machine upgrades
Bearing installation
Machine improvement
To remain competitive, plants must keep pace
with new machine technologies. SKF can help
to keep pace without the need to invest in
new machines. Recommendations can include
one, or a combination of actions:
@ptitude industrial decision support system

The @ptitude Industrial Decision Support
System from SKF is a knowledge management
system that incorporates todays most advanced
technologies to integrate data from multiple
sources into an easy to use reliability maintenance application. It enhances the user team
ability to make the right decision at the right
time, providing a structured approach to capturing and applying knowledge. A key element
of the @ptitude system is its online, webenabled asset management knowledge bank:
@ptitudeXchange subscribers have access to
articles, technical handbooks, white papers,
best practices and benchmarking information,
interactive decision-support programs and an
information network for expert advice and
services.
For additional information, please visit
www.aptitudexchange.com.
Upgrade, rebuild and re-design

Design engineering
Refurbishment of bearings
Repair and upgrade machine tool spindles
Instrument/equipment calibrations
Training
SKF Reliability Services offers comprehensive
machine reliability and asset management
training from the shop floor to the highest
level of management.
Proactive reliability maintenance

Following the Proactive Reliability Maintenance
process helps to provide best return on plant
assets. It addresses failures and implements the
processes necessary to prevent recurrence. The
SKF Proactive Reliability process is based on
four key steps:
Predictive maintenance, a multi-faceted
process that uses sophisticated technology
systems to gather comprehensive intelligence
on machine conditions and production
processes.
Diagnostics and Root Cause Analysis (RCA) to
identify problems and necessary actions, such
as machine alignment, balancing etc.
Key performance indicators are performance
improvement targets, established jointly
between SKF and the customer.
Periodic operational reviews between SKF
and the plant management to analyze
performance.
Integrated Maintenance Solutions

An Integrated Maintenance Solution (IMS)
agreement brings together all areas of expertise
offered by SKF, establishing a continuous
process of maintenance monitoring, analysis
and improvement. It provides a planned skills
transfer program for maintenance and operations personnel, and technology upgrades
where required.
With an IMS agreement, SKF Reliability
Systems will manage every key component of a
machine asset management strategy, providing
a total system for improving efficiency. Each
agreement is customized to specific business
needs. The user can choose which areas need
to be included, based on internal resources
and current supplier contracts. With an IMS
contract, SKF shares some of the risk as well as
the savings, while the user receives agreedupon financial returns with little to no capital
investment.
569
Other products
Condition monitoring products
At the core of the SKF product range are the

vibration detection, analysis and diagnostic
products, which enable process monitoring as
an added benefit. Some of those products are
shown below. More information about SKF condition monitoring products can be found online
at www.skf.com/cm.
Microlog family of data collectors

The SKF family of Microlog data collector/
analyzers is designed so that users can easily
establish a comprehensive periodic condition
monitoring program. As a diagnostic tool, the
Microlog is unequalled in its class. Embedded
intelligence provides step-by-step instructions
for performing critical analysis functions like
basic and advanced balancing, cyclic analysis,
run-up/coast-down, bump test, tracking filter or
motor current analysis. The frequency analysis
module enables overlay defect frequencies on
collected spectra to detect bearing defects, gear
mesh, misalignment, unbalance or looseness
problems.
MARLIN family of data managers

The MARLIN data management system
is designed to be the frontline tool for
operators, building the communications/technology bridge between operations, maintenance,
engineering and plant management. This
rugged high performance data collector provides a simple, convenient and portable way to
collect and store machine vibration, process,
and inspection data for quick downloading and
analysis.
Vibration Pen Plus

The Vibration Pen Plus offers users a way to
begin a cost-effective condition monitoring program, or to expand the responsibility for
machine reliability to operators throughout the
plant. A multi-parameter vibration monitoring
tool, the Vibration Pen plus operates with the
press of a button, measuring vibration according to ISO standards and utilizing acceleration
enveloping technology to identify a range of
bearing, gear mesh and other machinery problems.
Inspector 400 ultrasonic probe

The inspector 400 ultrasonic probe senses high
frequency sounds produced by leaks, electrical
discharges and equipment as it operates. It
electronically translates these signals using a
heterodyning process, making them audible
through a headset and visible as increments
on a meter. This enables maintenance personnel to detect pressure and vacuum leaks, arcing, tracking and corona in electric apparatus or
test bearings, pumps, motors, compressors etc.
Infrared temperature probe
This laser sighted non-contact thermometer
senses the temperature of an object with an
infrared detector, enabling maintenance personnel to take temperature readings in locations
that might otherwise be difficult to access.
Microlog CMVA65
Microlog MX series
MARLIN 1-pro
Vibration Pen Plus
Ultrasonic probe
Infrared thermometer
570
Condition monitoring products
Machine condition transmitter, online

monitoring units
SKF machine condition transmitters provide
vital information about bearing performance
and overall machine condition. This information
can be used to make sure that essential production equipment is kept running. This cost
effective system offers two adjustable warning
levels (alert and alarm) via two independent set
points with LED alarm indicators and output
relay contacts.
Online monitoring units provide around-theclock automated data collection and a powerful
array of analysis tools to optimize condition
monitoring efforts. If a machine starts to
develop a problem, the system helps to detect,
analyze and track the defect so that maintenance costs are minimized. A live mode
feature enables detailed online analysis, while
event logs provide a history of events that
may have occurred while the system was unattended.
Vibration sensors, eddy probes

SKFs in-depth bearing, machinery, monitoring
and signal processing knowledge was included
in the development of the CMSS2100 and
CMSS2200 vibration sensor series. These single
units can be used instead of the wide range of
accelerometers typically needed to meet a variety of conditions.
In addition to a full line of vibration sensors SKF

also offers eddy probe systems for the measurement of relative motion in sleeve bearing
machines.
SKF online monitoring system V/T

SKF wireless condition monitoring unit is a
compact, four-channel, permanently mounted
monitoring device that communicates using a
wireless network. It collects acceleration, velocity, temperature and bearing condition data and
automatically uploads it for viewing and analysis
in SKF @ptitude Monitoring Suite. Choosing a
wireless system can improve machine reliability,
reduce installation costs and increase personnel
safety.
SKF @ptitude monitoring suite software

Consisting of three modules Analyst,
Inspector, and Observer the SKF @ptitude
Monitoring Suite forms the basis for a
completely integrated approach to condition
monitoring, permitting fast, efficient and reliable
storage, manipulation and retrieval of large
amounts of complex machine and plant information. Designed from the ground up with
robust open databases and the familiar
Windows interface, this powerful software
accepts data from the full range of SKF data
collection devices and interfaces with
SKF @ptitude Decision Support to facilitate
consistent and reliable decision-making.
SKF @ptitude decision support

SKF multilog online system IMx
The SKF Multilog On-line System IMx is the
next generation of powerful, cost-effective solutions for a variety of condition monitoring applications. Together with SKF @ptitude Observer
software, Multilog IMx-T provides a complete
system for early fault detection and prevention,
automatic advice for correcting existing or
impending conditions and advanced conditionbased maintenance to improve machine reliability, availability and performance. The Multilog
IMx is available in wall-mounted or rack mounted configurations.
SKF @ptitude Decision Support is a dedicated

decision support software that links with a
range of data sources to facilitate accurate,
timely, and consistent decision making and work
order notification within a single plant or
across multiple facilities. By fusing knowledge
from diverse sources, SKF @ptitude Decision
Support provides the information essential to
effective machine and process analysis, diagnosis, reporting and corrective action. Overall
plant efficiency is improved by replacing laborintensive data analysis with an automated
process that identifies the probability of specific
faults within an asset or process and then prescribes appropriate action.
Machine condition transmitter
Vibration sensors
SKF online monitoring system V/T
SKF multilog online system IMx
SKF @ptitude monitoring suite software
SKF @ptitude decision support

571
Other products
Plain bearings
Spherical plain bearings and rod ends
Bushings
Spherical plain bearings, which are designed for

slow movement applications, can accommodate
misalignment and oscillating movements. They
have a very high load carrying capacity and are
ready to mount. Spherical plain bearings are
available with various sliding combinations: steel
on steel, which requires lubrication, or the
maintenance-free combinations steel on sinter
bronze composite, PTFE fabric or PTFE composite. SKF offers a very comprehensive range:
SKF offers the worlds widest assortment of

stock bushings. The range is suitable for rotating, oscillating and linear movements.
Cylindrical and flanged bushings, thrust washers
and strips are available. Different materials
serve different requirements.
Radial spherical plain bearings in metric

or inch dimensions, with seals and/or an
extended inner ring.
Angular contact spherical plain bearings for
combined radial and axial loads.
Spherical plain thrust bearings for thrust
loads and in combination with a radial
spherical plain bearing for heavy duty
arrangements.
Rod ends with integral spherical plain
bearings with male or female threads or
with cylindrical or rectangular section
welding shank.
Solid bronze, the traditional robust material.

Sintered bronze with oil impregnation for
high sliding velocities.
Wrapped bronze with lubrication pocket for
contaminated environments.
PTFE composite for long service life due to
low friction.
POM composite for low maintenance under
tough conditions.
Stainless backed composite, maintenancefree in corrosive environments.
PTFE polyamide, cost effective and
maintenance-free.
Filament Wound for extreme conditions.
For detailed information, please refer to
the SKF Interactive Engineering Catalog on
www.skfusa.com
For detailed information, please refer to

the SKF Interactive Engineering Catalog on
www.skfusa.com
Radial spherical plain bearings
Angular contact spherical plain and

spherical plain thrust bearings
Rod ends
Bushings
572
Linear motion and precision technologies
High efficiency screws

Ball screws
Ball screws convert rotary motion to linear
motion in a very efficient way. The load is
transmitted from the screw shaft to the nut
through a series of recirculating ball circuits.
There are a variety of recirculation systems
depending on the application demands. The ball
screws come in several precision classes to
offer reliable positioning accuracy and backlash
elimination.
Inch series ball screws

The inch series ball screws have a very robust
recirculating system, allowing optimum reliability. These ball screws are precision ground, or
commercial range and are available in preloaded or non-preloaded configurations.
Ground ball screws
Ground ball screws
Roller screws
The two basic types of roller screws are (planetary & recirculating), which will allow you to
operate beyond the limits of most ball screws.
The load transfers through the screw shaft to
the nut through a number of threaded rollers.
By virtue of their roller contacts there are a
larger number of contact points which results in
a much higher load carrying capacity, longer
life, and finer leads, than a comparably sized
ball screw.
Quick ship roller screws

There is a range of roller screws that are
available in stock, and can be shipped within
2 weeks.
Ball screw repair service

SKF now offers a ball screw repair program.
We can repair any brand of ball screw and
return it to its original operating condition. A
free evaluation can be supplied within 72 hrs.
and emergency repairs are available on request.
We have over 50 years of repair experience.
Ground ball screws
Ball and roller screws

573
Other products
Linear motion and precision technologies
Guiding & positioning

systems
Metric linear ball bearings
The metric linear bearing comprises a plastic
cage carrying hardened steel raceway segments
that transmit the load through the recirculating
balls into the supporting hardened steel shaft.
Metric linear bearings are available with a selfaligning feature as well as integral seals. All linear bearings are available as pillow block units
for easy mounting. The metric series of linear
bearings offers complete interchangeability to
market standard sizes.
Inch linear ball bearings

Inch linear ball bearings provide an economical
solution to suit a wide variety of applications.
SKF offers both steel sleeve and resin caged
linear bearings. The SKF inch series bearings
are available with a self-aligning feature as well
as integral seals. All linear bearings are assembled as pillow block units for easy mounting.
The inch series of linear bearings offers complete interchangeability to market standard
sizes.
Profile rail guides
Actuation systems
Profile rail guides provide high load capacity,

superb stiffness, and precise smooth motion.
The profile rail guide line is available in a four
ball row circulation design to allow for equal
loading from any direction. Each carriage features a lubrication reservoir that provides long
service life. For smooth, low noise operation,
the carriages are available with a ball separator
to dampen vibration. The profile rail guides offer
complete interchangeability to market standard
sizes.
SKF Actuation Systems develops and markets

systems that combine mechanics and electronics to provide integrated solutions for its customers. Today actuation systems are used within a wide range of products and applications.
Primary areas of operation are in medical technology, healthcare, hospital and nursing home
beds, rehabilitation, furniture, workplace
ergonomics, industrial and manufacturing technology, automation and robot engineering.
Precision rail guides

Precision rail guides are suitable for applications
with limited strokes requiring high rigidity and
position accuracy, and ultra smooth motion. The
precision rail guides using optimized rollers are
available with the patented ACS system that
ensures that the cage remains in the center of
the stroke at all times.
For additional information on Linear Motion

and Precision Technologies, please visit
www.linearmotion.skf.com.
Positioning systems
Positioning Systems provide compact and economical solutions for guided and driven applications. They may be designed to meet special
requirements.
Linear bearing shaft and accessories

Both metric and inch shaft is available from
SKF Easy Serve. SKF offers a prompt cut to
length service as well as full machined to print
capability. Shaft supports and end supports are
available for both metric and inch shaft.
Actuators
Linear ball bearings

574
Profile rail guides
SKF magnetic actuation range
Bearings for machine tools
Machine tool application require superior performance from the bearings used to support
spindles and precision ball screws. They must
exhibit this in terms of speed capability, system
temperature stability, rigidity, accuracy and
noise level; such characteristics are rarely met
by bearings for general purpose applications.
Therefore SKF produces special high-precision
bearings designed to satisfy the most demanding requirements in the machine tool
environment.

ABEC5, ABEC7 (P4A, PA9A)
SKF precision angular contact ball bearings are
non-separable and are essentially single row
angular contact ball bearings. In all such bearings the load is transmitted from one raceway
to another at an angle to the bearing axis.
These bearings can therefore carry axial loads
acting in one direction in addition to radial
loads. Axial forces produced in the bearing
when subjected to a radial load must be counteracted by an opposing force applied externally.
The bearings are therefore adjusted against a
second bearing.
To meet the requirements of modern
machine tool applications as fully as possible,
SKF precision angular contact ball
bearings are made in several series and
designs. They can be supplied single or in
matched bearing sets, and as full steel or
hybrids. Bearing sets are used when the load
carrying capacity of a single bearing is inadequate, or if axial loads acting in both directions
have to be accommodated.
In addition to standard precision bearings,
SKF also produces high-precision angular
contact ball bearings, intended for even higher
speeds and with extremely high running
accuracy.
Precision cylindrical roller bearings,

double and single row
Precision angular contact thrust ball

bearings
High precision cylindrical roller bearings are

bearings with a low cross section, high load
carrying capacity and speed capability. They are
therefore particularly suitable for machine tool
applications, and enable spindle bearing
arrangements to be designed for heavy radial
loads, high stiffness and relatively high speed.
SKF high precision single row cylindrical
roller bearings are used where increased speed
capability and more compact spindle design
are needed. The double row bearings are used
when there is a need for high-load carrying
capacity, and they are available with either
cylindrical bore or tapered bore. In the
machine tool field, cylindrical roller bearings
are generally supplied with a tapered bore, as
this design allows a certain radial internal
clearance or preload to be achieved by adjustment, when mounting bearings on a tapered
shaft.
Precision angular contact thrust ball bearings

are especially suited to applications demanding
accuracy and rigidity of machine tool work spindles. They have gained increasing popularity
with machine tool builders over the years, and
although not formally standardized, have
become a standard bearing throughout the
world. SKF offers two main families of angular
contact thrust ball bearings: the double direction thrust ball bearings series 2344 (00) and
the BTM series.
These bearings are able to locate a spindle
axially in both directions and are designed for
use with double row or single row cylindrical
roller bearings of series NN 30 K and N 10 K,
having the same bore and outside diameters.
The outside diameter of the housing washer is
however made to tolerances such that sufficient
radial clearance to the housing bore seating is
obtained. This is to ensure that the thrust
bearing is only subjected to axial loads. An
additional benefit is the simplified machining of
the housing bore.
Precision cylindrical roller bearings
Precision angular contact thrust ball bearings
Ball screw support bearings
575
Other products
Bearings for machine tools
Ball screw support bearings
Profile rail guides
Machine tool and spindle repair service
The precision ball and roller screws used to

drive positioning tables on CNC machine tools
have an important influence on work piece
quality. In recent years the large increase in
CNC machine tools with several controlled axes
has emphasized the need for good and reliable
positioning accuracy. In order to obtain this,
precision screws must be supported with bearings of special design to provide the optimum
axial run-out and rigidity characteristics.
Profile rail guides from SKF are modern

machine components used in the production of
linear guidance systems with unlimited travel.
They consist of a profile rail with four precisionground raceways and a slide unit with four ball
circulation paths. This design offers numerous
benefits:
Square configuration of the raceways
results in a guidance system with good
rigidity, capable of withstanding moment
loads in all directions.
Load carrying capacity is equal in all four
directions.
Lubrication reservoir standard for all
carriages provides long service life.
Ball separator available for low noise,
smooth operation requirements.
Ready-to-mount units allow economy
and simplicity of mounting.
Provided as standard with grease nipple
and all-round seals.
Rail cover strip protects carriage from
contamination that may settle on rail.
High operational speeds with quiet running
and low coefficient of friction.
Both manufacturers and rebuilders are acutely

aware of the long lead times needed to customize small lots of bearings to fill a particular
design requirement or replace a hard to get
bearing arrangement. These long lead times
frequently increase downtime for rebuilders and
delay production schedules for OEMs. To correct
this situation, SKF opened the Spindle Bearing
Service Centers. The Service Centers can customize duplex, triplex and quad bearing sets,
alter preloads and provide greased bearings
all within two weeks.
When the Service Center customizes an
SKF bearing, the bearing carries a full manufacturers warranty. With the SKF warranty, you
get the extra quality assurances that only the
manufacturer can provide. The bearings are
measured, modified, noise tested and packed in
a controlled environmentusing the same
exact standards as the factory.
Precision screws require bearings able

to provide:
High dynamic and static load rating
Speed capability
Superior axial rigidity
Extreme running accuracy, especially
in axial direction.
The SKF ball screw support bearings are
single direction angular contact thrust ball
bearings having a contact angle of 60.
SKF has a wealth of experience with machine
tool bearing applications, not only as a producer
of high-precision bearings but also as a user of
machine tools. This experience has been utilized
in designing bearings specifically for the support
of precision ball screws. As more than one
bearing is often required to support a screw,
matched sets of bearings are offered, requiring
no subsequent adjustment. To further simplify
mounting, complete ready-to-mount pregreased cartridge units incorporating matched
sets of single direction angular contact thrust
ball bearings in a flanged housing are supplied
on request.
Spindles
SKF is a worldwide supplier of a complete
range of spindles, both belt driven and motorized. SKFs customers for spindles are mainly in
the machine tool and woodworking industries,
but applications are also found in printing,
medical and factory automation.
Machine spindles
The following is a list of services that the

Spindle Bearing Service Center offers to all
SKF customers:
Preload modificationAll ranges of
preload can be accommodated in bearings
up to 10" outside diameter. After they are
face ground, the bearings are inspected,
measured, and sound tested.
MatchingSpecific bearing arrangements
can be supplied in dedicated pairs, triplex
sets and quad sets. Matching 15
and 25 bearings for special loading
conditions can also be accommodated.
Fitting ceramic balls into standard
bearingsHybrid bearings combine steel
bearing rings and ceramic balls where
very high speed and high stiffness are
important design considerations. To meet
this growing need, the Spindle Bearing
Service Center will refit SKF precision
angular contact ball bearings with silicon
nitride (ceramic) balls.
Grease packingSKF Bearings can be
supplied with many types of grease and
grease quantities. The Service Center can
fulfill requests for any special lubrication
requirements.
Spacers and kitsThe Service Center
can provide bearing kits containing
bearings and spacers matched as a set for
proper preload and/or specific stack height
dimension.
Special modificationsFace slots for
anti-rotation or slots for lubrication are
special modifications that fall within the
scope of the Service Center. Contact your
SKF Representative to discuss other
custom modifications.
For additional information, on Bearings for
Machine Tools, please call 1-800-541-3624.
Profile rail guides
576
Spindle repair service
Bearings for extreme operating environments
Bearings for extreme temperatures

Wherever very high or very low environmental
temperatures are a limiting factor, a special
bearing is normally needed. SKF offers a very
comprehensive range of extreme temperature
deep groove ball bearings that offer:
Low life-cycle cost
Extended service life
High reliability
Minimized maintenance
Wide operating temperature range
SKF extreme temperature bearings are
designed for the most common extreme
temperature applications such as kiln trucks
wheels, support rollers and general wheel
arrangements.
In addition to the well-proven deep groove
ball bearings, SKF range also includes
Y-bearings units for extreme temperatures,
available in three different housing styles with
a choice of two different bearing designs.
INSOCOAT electrically insulated

rolling bearings
Rolling bearings in electric motors, generators
or associated equipment are at risk from the
passage of electric current, which can damage
the surfaces of rolling elements and raceways in
the bearing and degrade the grease rapidly. The
risk of damage increases greatly if a frequency
converter controls the motor, which is becoming
increasingly common. In a frequency controlled
induction motor, an additional risk for high frequency bearing currents occurs due to the
inherent stray capacitances within the motor.
To solve this problem and to protect the
bearings against electric current passage, SKF
has developed INSOCOAT bearings electrically
insulated rolling bearings. An INSOCOAT bearing
is a very economical solution compared with
other insulation methods that protect the
bearing. By integrating the electrical insulation
function into the bearing, SKF has been able to
increase reliability and machine uptime by
virtually eliminating this failure mode.
INSOCOAT bearings offer many benefits:
Key ability to protect the bearing against
breakdown voltages up to 1000 V.
Avoid damage caused by electric current
leakage to achieve maximum bearing
service life
Higher operational reliability of electrical
machinery and lower maintenance costs
No additional design requirements, since
the bearing dimensions conform to ISO
standard and can be easily replace noninsulated bearings
High temperature bearings
INSOCOAT
TM
bearings
NoWear coated bearings

NoWear bearings make sense whenever bearings are failing prematurely due to severe operating conditions. NoWear bearings can withstand longer periods of insufficient lubrication,
sudden variations in load and rapid speed
changes, vibrations and oscillations.
NoWear bearings open up new possibilities to
existing applications operating under severe
conditions, without introducing major design
changes and allow freedom in new designs.
They have already been proven in a wide range
of extreme applications, including paper
machines, marine and offshore applications,
fans, compressors, hydraulic pumps and motors.
The combination of SKF know-how and the
processes and materials employed makes
NoWear a winning solution for your business.
Now you can significantly increase the lifetime
of bearings used in demanding operating environments, improve the performance of your
machinery, and reduce your risk of unplanned
downtime.
Switching to coated bearings often makes
sense whenever the life or speed of a standard
bearing is reduced due to lack of lubricant,
sudden load variations, contamination or high
operating temperatures. NoWear is proven in a
wide range of applications including:
Paper machines
Compressors
Hydraulic motors
Material Handling
Mining and Construction
Marine & Offshore
Racing
NoWear
TM
coated bearings
577
Other products
Bearings for extreme operating environments
Hybrid bearings
Solid oil
Ceramic materials are hard and resistant to

wear. In addition, they have electrical insulation
properties and are chemically inert in hard
conditions. SKF is increasingly incorporating
ceramic material into its bearing products;
currently SKF offers three different bearings
that incorporate ceramics:
All-ceramic bearings, where both rings
and rolling elements are made of ceramic.
Theses rotate easily and offer the benefits
of very high-speed capabilities, low weight,
good corrosion resistance, are nonmagnetic and can withstand temperatures
up to 1,800 F.
Hybrid bearings, where the rings are
made of steel while the rolling elements are
made of ceramic. This results in a wearresistant design that is also electrically
insulating. Compared with traditional allsteel bearings, the life of the hybrid version
could be increased by up to a factor of 10.
Hybrid designs are also capable of running
at very high speeds; shaft speeds can be
doubled and grease life extended more
than three time normal life expectancy
when compared to all-steel bearings.
When it comes to high-temperature
tolerance, hybrid bearings equipped with
special steel rings can work continuously at
temperatures of 900 F. One of the clear
advantages of this bearing is that it can be
used as a direct replacement for all-steel
bearings without any redesign of the
applications.
Single-ball hybrid bearings, where the
design features a single ceramic ball in an
otherwise all-steel bearing. The single hard
ceramic ball keeps the steel raceway free
from foreign particles in dusty and dirty
environments. It smoothes the raceway,
which increases service life under extremely contaminated conditions. This single-ball
hybrid bearing can replace a conventional
bearing without the need for remodeling.
Solid Oil is a polymer matrix, saturated with a

lubricating oil, which completely fills the internal
space in a bearing and encapsulates the cage
and rolling elements. By releasing the oil, Solid
Oil provides good lubrication for the rolling
elements and raceways during operation.
Hybrid bearings
578
Solid Oil has unique advantages:

It keeps the oil in position
It brings more oil to the bearing
than grease
It keeps contaminants out
Its resistant to chemicals
It can withstand large g forces
No relubrication needed
SKF can supply most normal sizes of ball and
roller bearings with Solid Oil. Some of the
application where Solid Oil is used are:
Papermaking
Equipment for snow and ice
Pneumatically operated coupling
Cranes and traverses
Mixers
Solid oil spherical roller bearing
Heavy engineering applications
Slewing bearings
Hydrostatic shoe bearings
Traction motor bearings
Slewing bearings are ball or cylindrical roller

bearings that can accommodate axial, radial and
moment loads acting either singly or in combination and in any direction. They are not
mounted on a shaft or in a housing; the rings,
which are simply bolted on the seating surface
are available in one of three executions
Developments in various industrial sectors have

led to the use of increasingly large bearings to
carry increasingly heavy loads. Examples of
these applications include the drums used to
grind ore and cement and the debarking drums
used in pulp production. The drums have in
some cases reached a size where conventional
rolling bearings or bearing units cannot be
used. SKF developed the hydrostatic shoe bearing for just this type of application. In addition
to having very high load carrying capacity these
bearings have the following advantages:
SKF provided the very first bearing designed

specifically for traction motors. Since then, SKF
has improved on the traction motor bearing
design with more than a dozen major refinements, all in direct response to needs of the
railroad industry.
SKF Traction Motor Bearings are designed
and built to survive in the heavy tonnage and
severe demands of the North American freight
railroads, which are among the most difficult in
the world.
without gears
with an internal gear
with an external gear.
Slewing bearings can perform both oscillating
(slewing) movements as well as rotating movements.
The outside diameter range of SKF slewing
bearings with a one-piece ring is from 400 to
7 200 mm. Even larger bearings are produced
with outside diameters up to 14 000 mm, but
these have segmented rings. Some of the
smaller sizes, up to approximately 2 000 mm
outside diameter are standard production.
Further information will be supplied on request.
Single row slewing ball bearings
Single row slewing roller bearings
Double row slewing bearings
Triple row slewing bearings
Other slewing bearings
In addition to the standard designs outlined
above, SKF also produces several other
designs, for a multitude of applications, to
order. These include:
Slewing bearings as combined cylindrical
roller/ball bearings
Slewing bearings as double row angular
contact ball bearings
Dry sliding slewing bearings
Slewing bearings with integral drive.
Slewing bearings
No limit to bearing size,

Friction is negligible,
Virtually no wear,
Bearing life is almost unlimited,
The sliding surfaces are self-aligning
Demands on accuracy of form of the
trunnion or runner to be supported are
moderate.
The SKF range comprises hydrostatic shoe

bearings for horizontal as well as vertical
bearing arrangements and also includes
combined hydrostatic bearings with integral
axial guidance.
Highly developed armature pinion and

commutator end bearings for all traction
and transit motors.
Specialized spherical roller bearings for
traction alternators and generators.
Traction motor support bearings and
tube-type housing assemblies.
TBU (tapered bearing unit) journal
bearings for freight care, rapid transit
and locomotive applications.
Specialized tools and maintenance
products for mounting, dismounting and
care of railway bearings.
Typical applications include:

Ore grinding mills
Cement mills
Debarking drums
Coal grinding mills
Rotary kilns
Air preheaters
Dryers for grain
Sugar diffusers
Heavy machine tools
Telescopes
A range of standard and special designs facilitate the choice of bearing for any individual
application.
For more information please contact the
SKF application engineering service
Hydrostatic shoe bearings
Traction motor bearings
579
Other products
Fastening systems, rolling elements
Shaft couplings
Supergrip bolts
SKF ConCentra bushings
SKF oil injection shaft couplings of type OKC

and OKF join two shaft ends rigidly to each
other. They are widely used in heavy torque
applications where power has to be reliably
transmitted. Applications range from joining the
propeller shafts on a ship to connecting shafts
in rolling mill drives.
SKF oil injection couplings are available as
cylindrical or flanged couplings for diameters
ranging from 100 to 1 000 mm. For more
information, please ask for the publication
OK oil injection couplings from SKF or visit
www.couplings.skf.com.
SKF Supergrip bolts, based on the SKF oil

injection principle, are compared with traditional
bolt systems easier to install and remove and
therefore offer important technical as well as
economic benefits. They are typically used in
applications where rotating flanged joints are
subjected to heavy torque loads and downtime
is particularly expensive, e.g. a ships propeller
shafts, steering equipment, steam turbines or
rolling mills.
SKF Supergrip bolts are available for hole
diameters starting from 40 mm.
For more information, please ask for publication The SKF Supergrip Bolt for Rotating
Flanges or visit www.couplings.skf.com.
Extremely low section height bushings for fully

concentric locking of friction hub joints virtually
eliminate the common problem with eccentricity
in shaft joints. The SHL design is a light-weight
locating device for moderate torque transmission e.g. in fans or slewing appliances.
Bushings
Solid bushings for fully concentric locking of
friction hub joints virtually eliminate the common problem with eccentricity in shaft joints.
Robust mechanical locating devices for high
torque transmission in slewing applications or
belt and chain drives. The SHT design contains
a slot for mounting in hubs. The SHR design is
closed for welding.
OK shaft couplings
OK shaft couplings
Bushings
SKF ConCentra bushings
580
Rolling elements
SKF also supplies loose rolling elements that
include balls, as well as cylindrical and needle
rollers. Using loose rolling elements it is possible to produce economic full complement
bearing arrangements for very heavy loads and
low speeds or oscillatory movement, provided
the other associated components can take the
form of raceways having the same hardness
and quality as bearing rings.
The rolling elements are made of carbon
chromium bearing steel or silicone nitride.
Additional information will be supplied on
request.
Rolling elements
MRC
MRC ball bearings

Single row deep groove ball bearing
(Type S)
Single row angular contact ball bearing

(R Series, XLS)
Split ring angular contact ball bearings

(97000 Series)
MRC S-type single-row ball bearings have no

filling notches and can carry significant radial
loads. Because of the uninterrupted raceway
grooves and the high degree of conformity
between balls and raceways, they can carry
substantial thrust loads in either direction, even
at very high speeds. Offered open or with single
or double shields or seals, as well as with snaprings in various combinations. Available in
1800, 1900, 100, 200, 300, 400 Series.
MRC R-type bearings feature one heavy race

shoulder and one counterbored race shoulder
on the outer ring. Because of this construction,
it is possible to incorporate a greater number of
balls than in the deep groove nonfilling notch
bearing. MRC R-type bearings have ample
radial and thrust capacity for the majority of
applications involving heavy radial load, heavy
single direction thrust load or both. Available in
1900, 100, 200, 300 Series. Supplied with 15
contact angles.
MRC also supplies a split inner ring 9000 Series

angular contact bearing. These bearings are
usually matched with a 7000 Series bearing of
the same size and contact angle. This arrangement offers two bearing thrust capacity in one
direction and one bearing thrust capacity in the
opposite direction. Single 9000 Series bearings
are also available.
Single-row filling-notch ball bearing

(Type M)
MRC's single-row maximum capacity M-type
bearings offer two important advantages over
other single-row types when used for heavily
loaded positions: they offer maximum radial
load-carrying capacity and have the ability to
carry heavy combined radial and thrust loads
where radial load predominates. MRC M-type
bearings are also referred to as a notch type
because they have a filling notch on one side of
the inner and outer rings. Available in 100,
200, 300, 400 Series.
Single row angular contact ball bearings

(7000 Series)
MRC angular contact ball bearings are used in
applications where a thrust load is applied in
one direction or where there are combined
radial and thrust loads. These bearings can also
be mounted in pairs for handling thrust loads in
both directions. Available with 29 and 40
contact angles in 7200, 7300, 7400 Series.
Additional MRC bearings and related

products:
Cartridge width single row deep groove
ball bearing
Felt seal replacement ball bearing
ABEC-7 machine tool spindle angular
contact ball bearing
ABEC-5 wood working single row deep
groove ball bearing
Dynomometer ball bearing
Taper bore adapter sleeve ball bearing
Conveyor roll ball bearings
Double row angular contact ball bearing

(5000 Series)
MRC double-row ball bearings are available in
two main types: C-type (Conrad construction)
and M-type (maximum capacity with filling
notches). All inner and outer rings have closure
grooves. These bearings may be equipped with
seals, shields, snap-rings or a combination of
these. Included in the MRC assortment is an
extra-wide double row bearing retrofit kit.
For additional information on

MRC Bearings please visit
www.skfusa.com/mrc
or order catalog # M190-730.
Split ring angular contact ball bearing
(97000 Series)
Single row filling notch ball bearing

(Type M)
Single row deep groove ball bearing

(Type S)
Single row angular contact ball bearing

(7000 Series)
Double row angular contact ball bearing

(5000 Series)
581
Other products
MRC
Marathon series corrosion-resistant mounted products and bearing units

Few industries challenge bearings with a harsher operating environment than the food and
beverage industries. Perhaps no industry works
as hard to meet regulations governing contamination. When MRC introduced the Marathon
Series Composite Mounted Bearing Units, it was
possibly the best solution to the problems associated with bearing failures.
Now the composite units are joined by our
HDiheavy-duty cast ironand XDs
extreme-duty cast stainless steelto more
thoroughly meet the needs of the industry.
The entire maintenance-free Marathon
Series is built to resist corrosion and is
designed for extended service life. At the heart
of the units are high-quality, corrosion-resistant
insert bearings, available with ZMaRC coating
or with stainless steel construction. The units
multifunction rubber seals are bonded to
AISI 304 stainless steel for superior corrosion
resistance, and sealed-for-life lubricants are
USDA approved.
Marathon series composite housing

The Marathon Series composite housing resists
citric acids, cooking fats and most chemicals
used in food and beverage processing. It is constructed of a thermoplastic composite material
that can be up to 61% lighter than cast iron
housings. Its spherical bore accommodates the
insert bearings spherical outer surface,
enabling the unit to fully compensate for initial
bearing seating misalignment.
Marathon series composite housings
582
Marathon Series units are available in the

following housing designs to meet the needs of
most food and beverage processing applications:
Pillow blocks
Two- or four-bolt flange
Tapped base
Three-bolt bracket flange
Narrow and wide slot take-up
Made-to-Order Items:
Low backing height pillow block
Low profile two- and three-bolt flange
Four-bolt piloted flange
Hanger
Marathon HDi ZMaRC coated cast iron

units with ZMaRC coated insert bearings
The Marathon HDi is a corrosion-resistant,
heavy-duty cast iron series of bearing units.
The cast iron housings, protected with MRCs
proven ZMaRC coating, eliminate the flaking
problems associated with nickel-plated products. The housings are matched with our
ZMaRC-plated, lubed-for-life, quality insert
bearings.
The HDi series provides a number of costsavings and performance benefits. As with all
Marathon products, MRCs patented two-part
stainless steel seals allow the units to operate
in heavy washdown environments without
regreasing. And since there is no need for
relubrication, continuous grease purge is
never a problem.
The HDi housing styles available include:
Pillow blocks
Two- or four-bolt flange
Tapped base
Marathon HDi series
Marathon XDs extreme duty cast

stainless steel mounted units
Composite housing units are suitable for many
food and beverage industry applications.
However, there are extremely challenging applications that require an even more durable
unitthe XDs line of Marathon units. These
housings are AISI 300 series cast stainless
steel with MRCs proven stainless steel insert
bearings.
The Marathon XDs stainless housings are the
strongest housings offered in the Marathon
family. For any application where loads are very
heavy or where shock loads are possible, the
extra strength and toughness of the stainless
steel housings are a benefit. Also, in applications where failure of the housing could result
in injury, such as in cases where workers pass
below a portion of a machine, the safety factor
inherent in the cast steel housing is desirable.
Exposure to extremely aggressive washdown
chemicals is another reason to choose these
stainless units.
The XDs housing styles available include:
Pillow block
Two- and four-bolt flange
Tapped base
Made-to-Order Items:
Three-bolt bracket flange
Wide and narrow slot take-up units
Compact two- and three-bolt flange
Piloted flange units

www.skfusa.com/mrc
Marathon XDs series
MRC
MTO the source for

custom bearing solutions
MRC PumPac bearings
Made-To-Order products can provide bearing

solutions to compensate for demanding operating conditions or unknown maintenance practices. By modifying a stock bearing or designing
and manufacturing a new bearing specifically
for the application, MTO Products are able to
supply practical solution to special requirements. And what sets MRC MTO Products
apart from local machine shops and rework
facilities is that the bearings carry the MRC
manufacturers warranty.
PumPac is an MRC bearing system designed as

a unique solution to the common problem of
premature thrust bearing failures in high speed
centrifugal pumps, as well as other applications
where duplexed angular contact ball bearings
are used.
PumPac is a matched set of bearings, consisting of a 40 angular contact ball bearing
mounted back-to-back with a 15 contactangle bearing. The 40 contact-angle bearing
supports the primary thrust load during operation, while the 15 contact-angle bearing
handles reverse thrust during start-up and
shut down, and supports radial loads during
normal operation.
PumPac bearings are manufactured to ABEC
3 tolerances, with special machined bronze
cages, and are high-temperature stabilized. By
using PumPac system, ball sliding and shuttling
are virtually eliminated, resulting in lower
operating temperatures, stable oil viscosity, consistent oil film thickness and longer service life.
The PumPac is also available in the 8000BB
PumPac Diamond series, which consists of a
matched set of 15 (B) bearings in a back-toback arrangement. This series is desirable in
high speed, lightly loaded applications in which
axial loads are balanced, resulting in reduced
operating temperatures and increased life.
MTO Products offer a broad size range of

singe- and double-row ball bearings in the
following styles:
Inch size R-type
Thin section 1800 and 1900 type
Single-row deep groove S-type
Single-row maximum capacity M-type
Single-row 15 angular contact R-type
Single-row angular contact 7000, 7000P,
7000PJ series
Single-row angular contact split ring
9000, 9000P series
Double-row angular contact 5000 series
PumPac 8000 series
Precision grade ABEC 5 and higher
Specialty bearings
For additional information on MTO products,

please order catalog # M200-111.
Made-to-order products

MRC PumPac bearings, please order
catalog # M200-100.
MRC PumPac bearings

www.skfusa.com/mrc
583
Other products
Magnetic bearings
Magnetic bearings
Magnetic bearings are used in a variety of
applications e.g. turbomolecular pumps,
compressors, turbo generators, semiconductor
equipment and high speed machine tools. They
levitate the shaft by inducing a controlled magnetic field. This means that the shaft is rotating
without contact. The system senses the shaft
position and adjusts the force in real time
keeping the shaft at the required position.
Some of the benefits of magnetic
bearings are:
No contamination from wear
Lubrication-free
Operate in severe environments e.g.
extreme high and low temperatures, ultrahigh vacuum or submerged applications
Minimal vibration transferred to housing
Precision control and elimination of shaft
runout caused by unbalance
Built-in condition monitoring of rotor
dynamics of vibration and forces
SKF offers a full range of magnetic
bearing products:
Magnetic bearings
Digital controllers
DC brushless motors
Hyperspin spindles
Engineered shaft solutions
For more information, please visit
www.revolve.com.
Magnetic bearings
584
Magnetic bearings
1200 series, self-aligning ball bearings . . . . . . . . . . . . . . . . . .80
300 series, deep groove ball bearings (max type) . . . . . . . . . .47
3200 A series, angular contact ball bearings . . . . . . . . . . . . . .70
3200 E series, angular contact ball bearings
16000 series, deep groove ball bearings . . . . . . . . . . . . . . . . .39
3300 A series, angular contact ball bearing . . . . . . . . . . . . . . .71
3300 E series, angular contact ball bearings
1726 series, inner ring bearing . . . . . . . . . . . . . . . . . . . . . . .281
3300 DNR series, angular contact ball bearing . . . . . . . . . . . .69
2
200 series, deep groove ball bearings (max type) . . . . . . . . . .47
30200 series,
Taper roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
Taper roller bearings, DF series (paired single row) . . . . . . .226
21300 series, spherical roller bearings . . . . . . . . . . . . . . . . . .146
30300 series, taper roller bearings . . . . . . . . . . . . . . . . . . . .217
31300 series,
22200 series,
spherical roller bearings (standard) . . . . . . . . . . . . . . . . . . .147
spherical roller bearings (sealed) . . . . . . . . . . . . . . . . . . . . .163
spherical roller bearings (printing press) . . . . . . . . . . . . . . .166
. . . . . . . . . . . . .72
. . . . . . . . . . . . .72
32000 series,
22300 series,
spherical roller bearings (shaker screen) . . . . . . . . . . . . . . .164
32200 series,
23000 series,
23100 series,
23200 series,

4
450000 series, spherical roller (printing press) . . . . . . . . . . .167
452300 series, spherical roller (shaker screen) . . . . . . . . . . .165
453300 series, spherical roller (shaker screen) . . . . . . . . . . .165
460000 series, spherical roller (printing press) . . . . . . . . . . .167
4762(00)B-VSB series, insert bearings . . . . . . . . . . . . . . . . .320
24000 series,
24100 series,
spherical roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
51100
51200
51300
51400
series,
series,
series,
series,
thrust
thrust
thrust
thrust
ball
ball
ball
ball
bearings
bearings
bearings
bearings
. . . . . . . . . . . . . . . . . . . . . .96
. . . . . . . . . . . . . . . . . . . . . .98
. . . . . . . . . . . . . . . . . . . . .100
. . . . . . . . . . . . . . . . . . . . .101

29200 series, spherical roller thrust bearings . . . . . . . . . . . .107
52200 series, thrust ball bearings . . . . . . . . . . . . . . . . . . . . .102



585
Index
BA2B 459000 series, angular contact ball bearings . . . . . . . .68
6000 series, deep groove ball bearing . . . . . . . . . . . . . . . . . . .32
Ball Bearing Units

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233
Introduction / product description . . . . . . . . . . . . . . . .234-239
Bearing selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240-243
Product specification tables . . . . . . . . . . . . . . . . . . . . .244-272
Insert bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273-281
Air handling ball bearing units . . . . . . . . . . . . . . . . . . .282-292
6200 series, deep groove ball bearings . . . . . . . . . . . . . . . . . .34
Ball screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .572
6200/C78 series, deep groove ball bearings . . . . . . . . . . . . . .46
Ball screw support bearings . . . . . . . . . . . . . . . . . . . . . . . . .576
Basic design
Angular contact ball bearings . . . . . . . . . . . . . . . . . . . . . . . . .51
CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
Cylindrical roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Deep groove ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Needle roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
Self-aligning ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Spherical roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .139
Thrust bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
7200 series, angular contact ball bearings . . . . . . . . . . . . . . . .62
Bearing type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Bearing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Bearings for machine tools . . . . . . . . . . . . . . . . . . . . . . . . . .575
6300/C78 series, deep groove ball bearings . . . . . . . . . . . . . .46

Bearings for extreme operating environment . . . . . . . . . . .577
A
Accessories, split pillow blocks (inch series)
Adapters SNW/SNP series . . . . . . . . . . . . . . . . . . . . . .424-430
Locknuts, lockwashers and lockplates . . . . . . . . . . . . .431-437
Withdrawal sleeves, removal nuts . . . . . . . . . . . . . . . .438-439
Accessories, split pillow blocks (metric series)
Adapters sleeves . . . . . . . . . . . . . . . . . . . . .516-517,
Withdrawal sleeves . . . . . . . . . . . . . . . . . . .516-517,
Locknuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .518,
Locknuts with locking clips . . . . . . . . . . . . . . . . .518,
Locking washers . . . . . . . . . . . . . . . . . . . . . . . . .518,
520-546
547-553
554-556
557-558
559-560
Actuation systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .574

Advanced calculation methods . . . . . . . . . . . . . . . . . . . . . . . .19
AH series, split pillow block (metric accessories) . . . . . .520-560
Air handling ball bearing units . . . . . . . . . . . . . . . . . . .282-292
AN series, split pillow block (inch accessories) . . . . . . . .432-434
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Technical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Introduction, highlights, and basic design . . . . . . . . . . . .51-61
Product specification tables . . . . . . . . . . . . . . . . . . . . . . .62-72
BS2-2200 series, spherical roller bearings (sealed) . . . . . . .163

BSYB 4752(00) series, insert bearings . . . . . . . . . . . . . . . . .321
Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .572, 580
C
C2200 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
C2300 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
C3000 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
C3100 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
C3200 series, CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
C39/000 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
C4000 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
CARB (sealed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
ASK series, split pillow block (inch accessories) . . . . . . .438-439
C4100 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
CARB (sealed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
Axial displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
C4900 series, CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
AOH series, split pillow block (metric accessories) . . . . .520-560
586
C5000 series, CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
FT-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . .270
C5900 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
CARB (sealed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
FY series, ball bearing units

FY-FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256
FY-RM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254
FY-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253
FY-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289
FY-WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255
C6000 series, CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

C6900 series,
CARB (standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
CARB (sealed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
Calculation tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CARB
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
Technical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
Introduction, highlights, and basic design . . . . . . . . . .171-175
ConCentra roller bearing units . . . . . . . . . . . . . . .299, 301, 305
Condition monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570
Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1b
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
FYE series, roller bearing units . . . . . . . . . . . . . . . . . . . . . . . .313

FYM series, ball bearing units
FYM-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257
FYM-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290
FYR series, roller bearing units . . . . . . . . . . . . . . . . . . . . . . .314
FYRP series, roller bearing units . . . . . . . . . . . . . . . . . . . . . . .315
FYT series, ball bearing units
FYT-FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261
FYT-RM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
FYT-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258
FYT-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291
FYT-WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260
FYTM series, ball bearing units
FYTM-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
FYTM-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292
G
D
G-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . . .272

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
HA series, split pillow blocks (metric accessories) . . . . . .520-560
Designations for rolling bearings . . . . . . . . . . . . . . . . . . . . . .2-4
HE series, split pillow blocks (metric accessories) . . . . . .520-560
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .564
Heavy engineering applications . . . . . . . . . . . . . . . . . . . . . . .579
H
H series, split pillow blocks (metric accessories) . . . . . . .520-560
ECB 23200 series, spherical roller (printing press) . . . . . . . .166
HK series, needle roller bearings . . . . . . . . . . . . . . . . . . . . . .190
ECB 23900 series, spherical roller bearings . . . . . . . . . . . . .162
HM series, split pillow block (metric accessories) . . . . . .520-560
ECB 24000 series, spherical roller bearings . . . . . . . . . . . . .162
Hybrid bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .578
ECBI 11200, spherical roller bearings . . . . . . . . . . . . . . . . .168
Hydraulic tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .562
Engineering consultancy services . . . . . . . . . . . . . . . . . . . . . .20
Hydrostatic shoe bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .579
Equivalent dynamic bearing load . . . . . . . . . . . . . . . . . . . . . .15

Explorer bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
I
I 112000 series, spherical roller bearings . . . . . . . . . . . . . . .168
I 26300 series, spherical roller bearings . . . . . . . . . . . . . . . .168
F-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . . .269
FSYE series, roller bearing units

FSYE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .308
FSYE-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309

Insert bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273-281
INSOCOAT, electrically insulated rolling bearings . . . . . . . . . . .577
587
Index
Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .563
Internal clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Ball bearing units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242
CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
Mounted products, please reference...

Ball bearing units
Roller bearings units
Split pillow blocks
Mounting and dismounting . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Split pillow blocks (metric series) . . . . . . . . . . . . . . . . . . . . 457
Split pillow block SNL 30 and 31 (metric series) . . . . . . . . .499
MRC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .581
MRC Marathon series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .582

MRC MTO Made to Order bearings . . . . . . . . . . . . . . . . . .583
MRC PumpPac bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .583
KM series, split pillow blocks (metric series) . . . . . . . . . .520-560
N
L
Linear motion and precision technologies . . . . . . . . . . . . . .573
N series, cylindrical roller bearings

200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
2200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
300 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Load carrying capacity and life . . . . . . . . . . . . . . . . . . . . . . . .12
N series, split pillow block (inch accessories) . . . . . . . . .432-436
Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
Split pillow blocks (inch series) . . . . . . . . . . . . . . . . . . . . . . .351
Split pillow blocks (metric series) . . . . . . . . . . . . . . . . . . . . .460
Split pillow blocks SNL 30 and 31 (metric series) . . . . . . . .500
Thrust bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
NA series, needle roller bearings

4800 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
4900 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
6900 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195
Linear ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .574
NCF series, cylindrical roller bearings . . . . . . . . . . . . . . . . . . .130

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
Lubrication
Split pillow blocks (metric series) . . . . . . . . . . . . . . . .454, 496
NJ series, cylindrical roller bearings

1000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
2200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
2300 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
300 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
400 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
NJG series, cylindrical roller bearings . . . . . . . . . . . . . . . . . . .131
Lubrication products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .565
NK series, needle roller bearings . . . . . . . . . . . . . . . . . . . . . .196
Lubrication selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
NKI series, needle roller bearings . . . . . . . . . . . . . . . . . . . . . .199
Lubrication systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .566
NKIS series, needle roller bearings . . . . . . . . . . . . . . . . . . . . .201
M
Machine tool bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .576
Magnetic bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .584
Materials for rolling bearings . . . . . . . . . . . . . . . . . . . . . . . . .21
Maintenance products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .561
MB series, split pillow block (metric accessories) . . . . . .520-560
Mechanical tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .561
Misalignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
588
NKS series, needle roller bearings . . . . . . . . . . . . . . . . . . . . .202

NNC series, cylindrical roller bearings . . . . . . . . . . . . . . . . . . .134
NNCF series, cylindrical roller bearings . . . . . . . . . . . . . . . . . .134
NNCL series, cylindrical roller bearings . . . . . . . . . . . . . . . . . .134
NNF series, cylindrical roller bearings . . . . . . . . . . . . . . . . . . .135
Nomenclature
CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169

Inner ring ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . .274
Roller bearing units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297
Spherical roller thrust bearings . . . . . . . . . . . . . . . . . . . . . . .89
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425
SAW split pillow blocks . . . . . . . . . . . . . . . . . . . . . . . . . . .403
SDAF extended range . . . . . . . . . . . . . . . . . . . . . . .408-409
standard range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329
TY/TFT-RPA Top Angle Take-up Units . . . . . . . . . . .392-393
SNL standard range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441
SNL 30 / 31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487
Thrust ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
NoWear, coated bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .577
NU, NUP series, cylindrical roller bearings
1000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
2200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
2300 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
300 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
400 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
O
OH series, split pillow block (metric accessories) . . . . . .520-560
OSNP Hydraulic assist adapter series . . . . . . . . . . . . . . . . . .424
OSNW Hydraulic assist adapter series . . . . . . . . . . . . . . . . .424
P
PL series, split pillow block (inch accessories) . . . . . . . . . . . . .436
Plain bearings and rod ends . . . . . . . . . . . . . . . . . . . . . . . . .572
Pop Release roller bearing units . . . . . . . . . . . . .see ConCentra
Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
R
Reliability and services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .568
R-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . . .271
RNA series, needle roller bearings
4800 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
4900 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
6900 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
Rod ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .572
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297
Seal selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304-305
Roller screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .573
Rolling elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .580
S
S-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . . .267
SAF series, split pillow blocks (inch series)
1300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .358
1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .360
1600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362
22200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .364
22300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .366
22500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .368
22600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .370
23000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .372
SAF series, split pillow blocks (inch series) - CARB
C2200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374
C2300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .376
C2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .378
C2600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .380
C3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .382
SAW series, split pillow blocks (inch series)
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .403
23200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .404
23500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .406
Precision bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .575

Preload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Printing press bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
Profile and precision rail guides . . . . . . . . . . . . . . . . . .574,576
Q
QJ200 series, angular contact ball bearings . . . . . . . . . . . . . . .65
SDAF series, split pillow blocks (inch series)

22200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .384
22300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386
22500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388
22600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390
23000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .412
23100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .416
23200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .420
QJ1000 series, angular contact ball bearings . . . . . . . . . . . . . .67
Seals
Roller bearing units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304
Split pillow blocks (metric series) . . . . . . . . . . . . . . . .444, 490
Quiet running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Seals, SKF range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .567
QJ300 series, angular contact ball bearings . . . . . . . . . . . . . . .66
589
Index
Selecting bearing size using the life equations . . . . . . . . . . .12

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Separator filter dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .567
Shaft couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .580
Shaft fits
Split pillow block housings . . . . . . . . . . . . . . . . . . . . . . . . . .351
Shaker screen bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
SK series, split pillow block (inch accessories) . . . . . . . . .438-439
Slewing bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .579
Snap rings & grooves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
SNL series, split pillow blocks (metric series)
for bearings on adapter sleeves . . . . . . . . . . . . . . . . . .462-473
for bearings with cylindrical bore . . . . . . . . . . . . . . . . .474-483
Sealing arrangements . . . . . . . . . . . . . . . . . . . . . . . . .484-486
SNL 30 and 31 series, split pillow blocks (metric series)
for bearings on adapter sleeves . . . . . . . . . . . . . . . . . .502-509
for bearings with cylindrical bore . . . . . . . . . . . . . . . . .510-515
SNP series, split pillow block (inch accessories) . . . . . . .427-430
SNW series, split pillow block (inch accessories) . . . . . . .426-430
Solid Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .578
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Spherical plain bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . .572
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .576
Split pillow block (inch series)
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329
Seals & speed limits . . . . . . . . . . . . . . . . . . . . . . . . . . .335-345
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .346-350
Shaft fits / housing loads . . . . . . . . . . . . . . . . . . . . . . .351-357
TY-RPA Top angle take-up units . . . . . . . . . . . . . . .392-401

SAW split pillow blocks . . . . . . . . . . . . . . . . . . . . . . .403-407
SDAF extended range . . . . . . . . . . . . . . . . . . . . . . .408-423
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .424-439
Split pillow block SNL (metric series), 20-160 mm bore
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .444-450
End covers, locating rings, displacement . . . . . . . . . . .451-453
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454-456
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .457-459
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460-461
Split pillow block SNL 30 / 31 (metric series) >180 mm bore
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .490-493
End covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .494-495
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .496-498
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .499
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500-501
Split pillow block SNL accessories . . . . . . . . . . . . . . . .516-560
SR-FM series, ball bearing units . . . . . . . . . . . . . . . . . . . . . . .268
Static load carrying capacity . . . . . . . . . . . . . . . . . . . . . . . . . .17
Stiffness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Supergrip bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .580
SY series, ball bearing units
SY-FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247
SY-PF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286
SY-RM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245
SY-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244
SY-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285
SY-WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .246
SYE series, roller bearing units
SYE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306
SYE-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307
SYH series, ball bearing units
SYH-FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252
SYH-RM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250
SYH-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249
SYH-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287
SYH-WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
SYM series, ball bearing units
SYM-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248
SYM-TF/AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288
SYR series, roller bearing units
SYR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310
SYR-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .311
SYT series, roller bearing units . . . . . . . . . . . . . . . . . . . . . . . .312
590
T2 series, taper roller bearings . . . . . . . . . . . . . . . . . . . . . . . .225
W series, split pillow block (inch accessories) . . . . . . . . .432-436
Wide Inner Ring Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .238

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
TFT series,
roller bearing units . . . . . . . . . . . . . . . . . . . . . . . . . . . .316-321
split pillow blocks (inch, take-up frames) . . . . . . . . . . .398-401
Y
YAR-2F series, insert bearings . . . . . . . . . . . . . . . . . . . . . . . .278
YAT series, insert bearings . . . . . . . . . . . . . . . . . . . . . . . . . . .280
YEL series, insert bearings
2F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276
2F CW series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277
YET series, narrow inner ring insert bearings . . . . . . . . . . . .275

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Seating washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94-95
Product specification tables . . . . . . . . . . . . . . . . . . . . . .96-106
Thrust pak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Traction motor bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .579
TU series, ball bearing units
TU-FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265
TU-TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263
TU-WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264
TUM-TF series, ball bearing units . . . . . . . . . . . . . . . . . . . . .266
TY-RPA series, split pillow blocks
(inch, take-up frames) . . . . . . . . . . . . . . . . . . . . . . . .394-397
U
U200 series, thrust ball seating washers . . . . . . . . . . . . . . . . .94
V
Variations
CARB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
591

Catalogo SKF

Enviado por

Dados do documento

Descrição original:

Direitos autorais

Formatos disponíveis

Compartilhar este documento

Compartilhar ou incorporar documento

Opções de compartilhamento

Você considera este documento útil?

Este conteúdo é inapropriado?

Direitos autorais:

Formatos disponíveis

Catalogo SKF

Enviado por

Direitos autorais:

Formatos disponíveis

Deep groove

6200-2Z J/C3 HC5 GJN

1. Seals, shields & snap rings:

Contact seal of synthetic rubber

Full ceramic bearing

Contact seal of synthetic rubber

Machined brass cage,

Contact seal of synthetic rubber

Special specifications for

Pressed brass cage,

Cage of glass fiber reinforced

High temperature, long life

Wide temperature range,

High temperature NLGI 2

Long life, quiet running

Medium temperature, quiet

Medium temperature, quiet

Dow Corning Molykote

Shell Aeroshell #7,

Pressed steel cage,

Low friction seal of synthetic

Low friction seal of synthetic

Shield on one side

Low friction seal of synthetic

Low friction seal of synthetic

Shields on both sides

Combination of C70 and C08

Clearance < Normal

Reduced I.R. and O.R. diameter

Snap ring groove and snap ring

Ceramic ball set

Low temperature NLGI 2

Deep groove ball bearings

In accordance with ISO 15-1998

Up to 52 mm O.D. P5, ABEC 5

Machined brass (M)

Axial load max

0.5 x C0 for 6200, 6300 and 6400 series

2RS1 Synthetic rubber (NBR) seals

ABEC 5 single row bearings

Deep groove ball bearings are used in a

SKF produces single row deep groove ball

Deep groove ball bearings with filling

SKF Explorer class

Quality performance in demanding applications

Optimized internal geometry

Large product assortment

In the USA, SKF offers bearings with

GJN grease provided as

Deep groove ball bearing

Deep groove ball bearings

Bearings with contact seals

Bearings with shields, designation suffix Z or

Safety precautions for fluoro rubber

Bearings with low friction seals

Bearings in the 60, 62 and 63 series up to

Bearings with snap ring groove

Always wear protective goggles, gloves and

Bearings with shields or seals at both sides are

The masses given in the tables are for the basic

Radial internal clearance (Table 1)

Radial internal clearance

102 0.0021 0.0040