Escolar Documentos
Profissional Documentos
Cultura Documentos
Table of Contents 1 Before You Begin .............................................................................................................................. 2 2 VPN Lite Router Setup Utility .......................................................................................................... 3 3 Advanced Users ................................................................................................................................. 6 3.1 Using the Router Webpage for Configuration ........................................................................... 6 3.2 Changing the LAN IP ................................................................................................................. 8 3.3 Changing the routing table ....................................................................................................... 10
After a short while, a window will open that will allow you to configure your router to connect as a site on the VPN, and also to have an Internet Connection if it is needed for the site. If the setup utility cannot connect to the ADSL router then error shown below will be displayed. Click OK and then cancel to exit the utility. Please check the following: 1. Is the router on? 2. Is the PC plugged into the router with an Ethernet Cable?
Run the utility again once the problem is fixed. If the error message persists please phone the VPN Lite help desk. Once the Setup Utility connects to the ADSL router then you can configure your VPN connection settings. You can do this by simply adding the VPN Lite username and password that was configured on the VPN Lite administrator Website, and adding the LAN IP details. Please note that the username includes the realm name as seen in the figure below. The LAN IP Address and subnet mask must be added exactly as configured on the VPN Lite Webpage. The DHCP server on the ADSL router will use this range to dynamically push down IP addresses in this range. The IP address must be given in a classless CIDR format (IP Address / Subnet-mask) as seen on the VPN Lite Management Webpage (e.g 10.0.14.0/24). Note: The IP Address for each site must fall in a different subnet. Example: site1@evpn.lite.0001 can be 10.0.1.0/24, then the subnet for site2@evpn.lite.0002 must be a different subnet, like 10.0.2.0/24. The IP Address must correspond exactly to the one configured on the VPN Lite Management page.
If you do not have an Internet account at this site then your Internet configuration block can be left unselected. If this is the case, the Internet account will be set to login to guest@telkomadsl which will only allow access to the www.telkom.co.za website, thus allowing the use of the VPN Lite service without having to login to the Internet.
If the you would like the computers connected to this site to have access to the Internet then you must check the tickbox next to Do you have a Internet account? You will then be able to fill in your username and password into the corresponding textboxes. An ADSL Internet account is sold separately, and can be bought from any ISP.
3 Advanced Users
Open your web browser and enter 10.0.0.2 ( or the routers new IP address if you have already changed this ) and press enter. Enter the applicable Username and Password ( both will be admin if you have not changed them already) Click " Advanced", move mouse over WAN and click "quickstart".
If you are have Internet access enter the ISP username and password into the applicable fields. If no ISP account is used then ignore changing the Internet access, and leave the default Telkom guest account details in these fields. If you change these details, you will need to chick the apply button to confirm the changes.
Enter a VPNLite into the Name field, enable sharing, select PVC 8:35, disable(de-select) NATand firewall, disable(de-select) Default gateway and enter the username and password as it was setup on the VPN Lite website. Click on Apply once everything has been entered.
Verify that both connections are running by clicking on Status and then Connection Status. Please allow a few minutes for the connection to be established.
Change the IP address to x.x.x.2, Netmask, start IP and End IP to the values obtained from the VPN lite website. Note that the netmask must be in the required format (for example IP = 10.x.x.x , Netmask = 255.255.255.0) and not the classless CIDR format (IP Address / Subnet-mask) as seen on the VPN Lite Management Webpage. Click on Apply when done.
Unplug the LAN cable from the PC, wait for a few seconds and plug the cable back in order to get a new IP from the router. To access the routers web interface, use the IP Address entered on the previous screen in the address field of the web browser. Now click on Save settings to store the changes on the modems webpage.
Add the following by entering the information one at a time in the fields supplied. Remember to click Apply after each row that is entered. Destination Gateway Mask Connection 192.168.0.0 0.0.0.0 255.255.0.0 VPNLite 172.16.0.0 0.0.0.0 255.240.0.0 VPNLite 10.0.0.0 0.0.0.0 255.0.0.0 VPNLite 0.0.0.0 0.0.0.0 0.0.0.0 Quickstart Click Save Settings once all the entries have been made. END