Escolar Documentos
Profissional Documentos
Cultura Documentos
This handbook contains information on the Triumph T595 Daytona and T509 Speed Triple motorcycles. Always store this handbook with the motorcycle.
Warning Labels At certain areas of the motorcycle, the symbol (right) can be seen. The symbol means CAUTION: REFER TO THE HANDBOOK and will be followed by a pictorial representation of the subject concerned. Never attempt to ride the motorcycle or make any adjustments without reference to the relevant instructions contained in this handbook. See pages 8 and 9 for the location of all labels bearing this symbol. Where necessary, this symbol will also appear on the pages containing the relevant information. Maintenance To ensure a long, safe and trouble free life for your motorcycle, maintenance should always be carried out by an authorised Triumph dealer. Only an authorised Triumph dealer will have the necessary knowledge, equipment and skills to maintain your Triumph motorcycle correctly. Information The information contained in this publication is based on the latest information available at the time of printing. Triumph reserves the right to make changes at any time without prior notice, or obligation. Not to be reproduced wholly or in pan without the written permission of Triumph Motorcycles Limited. 0 1996 Triumph Motorcycles Limited, Hinckley, Leicestershire, England. Publication part number 3855001 issue 2.
! n
P-l c
Page 1
Foreword
Owners Handbook Thank you for choosing a Triumph motorcycle. This motorcycle is the product of Triumphs use of proven engineering, exhaustive testing, and continuous striving for superior reliability, safety and performance. Please read this owners handbook before riding in order to become thoroughly familiar with the correct operation of your motorcycles controls, its features, capabilities and limitations. This handbook includes safe riding tips, but does not contain all the techniques and skills necessary to ride a motorcycle safely. Triumph strongly recommends that all riders undertake the necessary training to ensure safe operation of this motorcycle.
WARNING: This owners handbook and all other instructions which are supplied with your motorcycle should be considered a permanent part of your motorcycle and should remain with it even if your motorcycle is subsequently sold. All riders must read this owners handbook and all other instructions which are supplied with your motorcycle before riding in order to become thoroughly familiar with the correct operation of your motorcycles controls, its features, capabilities and limitations. Do not lend your motorcycle to others as riding when not familiar with your motorcycles controls, features, capabilities and limitations can lead to an accident.
Table of Contents This handbook contains a number of different sections. The table of contents below will help you find the beginning of each section where, in the case of the major sections, a further table of contents will help you find the specific subject required. Foreword................................................................... 1 Warning Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Parts.Identification .............................................................................................................10 Serial Numbers...................................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...13 General Information...........................................................................................................15
Page2
not correctly followed could result in personal injury, or loss of life. This caution identifies special instructions or procedures which, if not strictly observed, could result in damage to, or destruction of, equipment. NOTE:
l
This note symbol indicates points of particular interest for more convenient efficient and operation.
Page 3
Always turn off the engine when refuelling. Do not refuel or open the fuel filler cap while smoking or in the vicinity of any naked flame. Take care not to spill any petrol on the engine, exhaust pipes or silencers when refuelling. If petrol is swallowed, inhaled or allowed to get into the eyes, seek immediate medical attention. Spillage on the skin should be immediately washed off with soap and water and clothing soiled with should immediately be petrol removed. Burns and other serious skin conditions may result from contact with petrol. WARNING: The rider must maintain c o n t r o l o f t h e vehicle by keeping hands on the handlebars at all times. The handling and stability of a motorcycle will be adversely affected if the rider removes his hands from the handlebars, resulting in loss of control or an accident.
Page 4
WARNING: Always turn off the engine and remove the ignition key before leaving the motorcycle unattended. By removing the key, the risk of use of the motorcycle by unauthorised or untrained persons is reduced. When parking the motorcycle, always remember the following:The engine and exhaust system will be hot after riding. DO NOT park where pedestrians, animals and/or children are likely to touch the motorcycle. Do not park on soft ground or on a steeply inclined surface. Parking under these conditions may cause the motorcycle to fall over. For further details, please refer to the How to Ride the Motorcycle section of this owners handbook. WARNING: Footrests provided must always be used by rider and passenger during operation of the vehicle. By using the footrests, both rider and passenger will reduce the risk of with inadvertent contact any motorcycle components and will also reduce the risk of injury from entrapment of clothing.
WARNING: Never ride the motorcycle when fatigued or under the influence of alcohol or other drugs. Riding when fatigued or under the influence of alcohol or other drugs reduces the riders ability to maintain control of motorcycle and may lead to loss of control and an accident. Riding when under the influence of alcohol or other drugs is illegal.
Magnesium alloy grinding fines are highly flammable. Always ensure that correct procedures and equipment are used to avoid the risk of fire. Suitable protective flame-resistant clothing must be worn. Never permit naked flames, cutting and welding operations or smoking in the working area. Magnesium alloy components incorporated in this motorcycle include, engine covers, cam cover and the headlight support. WARNING: Always ride defensively and wear the protective equipment mentioned elsewhere in this foreword. Remember, in an accident, a motorcycle does not give the same impact protection as a car.
Page 5
WARNING: Consult your authorised Triumph dealer whenever there is doubt as to the correct or safe operation of this Triumph motorcycle. Remember that continued operation of an incorrectly performing motorcycle may aggravate the fault and may also prejudice safety. WARNING: When riding the motorcycle both rider and passenger must always wear a crash helmet, eye protection, gloves, trousers (close fitting around the knee and ankle) and a brightly coloured jacket. Brightly coloured clothing will considerably increase a riders (or passengers) visibility to other operators of road vehicles. Although full protection is not possible, wearing correct protective clothing can reduce the risk of injury when riding. WARNING: A crash helmet is one of the most important pieces of riding gear as it offers protection against head injuries. You and your passengers crash helmet should be carefully chosen and should fit you or your passengers head comfortably and securely. A brightly coloured helmet will increase a riders (or passengers) visibility to other operators of road vehicles. An open face helmet offers some protection in an accident though a full face helmet will offer more. Always wear a visor or approved goggles to help vision and to protect your eyes.
Page 6
WARNING: Owners should be aware that the only approved parts, accessories and conversions for any Triumph motorcycle are those which carry official Triumph approval and are fitted to the motorcycle by an authorised dealer. Triumph does not accept any liability whatsoever for defects caused by the fitting of non-approved parts, accessories or conversions or the fitting of any approved parts, accessories or conversions by non-approved personnel. In particular, it is extremely hazardous to fit or replace parts or accessories whose fitting requires the dismantling of, or addition to, either the electrical or fuel systems and any such modification could cause a safety hazard. The fitting of any non-approved parts, accessories or conversions may adversely affect the handling, stability or other aspect of the motorcycle operation which may result in an accident causing injury or death.
WARNING: This Triumph motorcycle should be operated within the legal speed limits for the particular road travelled. Operating a motorcycle at high speeds can be potentially dangerous since the time available to react to given traffic situations is greatly reduced as road speed increases. Always reduce speed in potentially hazardous driving conditions such as bad weather or heavy traffic. WARNING: Continually observe and react to changes in road surface, traffic and wind conditions. All two-wheeled vehicles are subject to external forces which may cause an accident. These forces include but are not limited to: . .
l
Wind draft from passing vehicle S Uneven or holed road surfaces. Bad weather. Rider error.
Always operate the motorcycle at moderate speed and away from heavy traffic until you have become thoroughly familiar with its handling and operating characteristics. Never exceed the legal speed limit.
Page 7
Warning Labels
WARNING LABEL LOCATION The labels detailed on this and the following page draw your attention to information in this handbook. Before riding, ensure that all riders have understood and complied with all the information to which these labels relate.
CHEQUEQS DE +EGURIDAD DIARIOS VERIFICACOES DIARIAS DE SEGURANCA VERIFICHE GIORNALIERE DI SICUREZZA DAGELIJSKE VEILIGHEIDSINSPECTIES
Crash Helmet
Coolant
(Page 44)
Engine Oil
(page 41)
Fairing Stowage
(Page 3 5
Page 8
Warning Labels
WARNING LABEL LOCATION (continued)
Windscreen Cleaning
(page 64)
Running In
(Page 24)
Gear Position
(Page 29)
Drive Chain
(page 48)
Tyres
(Page 58)
Page 9
Parts Identification
10
11
T509-28b
1. 2. 3. 4. 5.
6.
indicator Headlamp Position Lamp Rear Lamp Radiator Oil Cooler Drive Chain
8. 9.
10. Front Brake Disc 11. Front Brake Caliper 12. Fuel Tank 13. Fuel Filler Cap 14. Seat Lock
7.
P a g e 10
Parts Identification
16
26
15
22
27
28
17
18
25
19
20
21
23
24
15. Battery 16. Tool Kit 17. Rear Brake Disc 18. Rear Brake Caliper 19. Rear Brake Fluid Reservoir 20. Rear Brake Pedal 21. Oil Level Sight Glass
22. Oil Filler Plug 23. Clutch Cable 24. Front Fork 2.5. Rear Suspension Unit 26. Coolant Expansion Tank 27. Coolant Pressure Cap 28. Silencer
Page II
Parts Identification
13
12
14
1. 2. 3. 4. 5. 6. 7.
Clutch Lever Passing Button Headlamp Dipswitch Horn Button Indicator Switch Ignition Switch Front Brake Fluid Reservoir
8. 9.
10. Starter Button 11. Headlight Switch 12. Tachometer 13. Speedometer 14. Warning Lights
Page 12
Serial Numbers
1. V.I.N. Number Vehicle Identification Number (UN.) The vehicle identification number is stamped into the steering head. It is also displayed on a plate, riveted to the frame, immediately behind the steering head.
1. Engine Serial Number Engine Serial Number The engine serial number is stamped on the crankcase, immediately above the clutch cover.
Page 13
Serial Numbers
THIS PAGE IS INTENTIONALLY FREE FROM INFORMATION
Page I4
General Information
Contents instrument Panel Layout . . . . . . . . . . . . . . . . Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . Coolant Temperature Gauge . . . . . . . . . . . Warning Lights . . . . . . . . . . . . . . . . . . . . . . . . Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition Switch/Steering Lock . . . . . . . . . . . . Brake Lever Adjuster . . . . . . . . . . . . . . . . . . Right Handlebar Switches ...... .....
16 16 16 17 17 18 18 19 20 21 22 22 23 23 23 23 24 25
Left Handlebar Switches . . . . . . . . . . . . . . . . Fuel Requirement . . . . . . . . . . . . . . . . . . . . . Fuel Tank Cap . . . . . . . . . . . . . . . . . . . . . . . . Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handbook Storage . . . . . . . . . . . . . . . . . . . . Seat Lock Operation/Seat Removal . . . . . . Running-in . . . . . . . . . . . . . . . . . . . . . . . . . . . Safe Operation . . . . . . . . . . . . . . . . . . . . . . . .
Page 15
General Information
INSTRUMENT PANEL LAYOUT
6 13
1. 2. 3. 4. 5. 6. 7.
Tachometer Tachometer Red Zone Speedometer Odometer Trip Meter Trip Meter Reset Knob Coolant Temperature Gauge
8. Turn Indicator light 9. Low Oil Pressure Warning Light 10. High Beam Indicator Light 11. Neutral Indicator Light 12. Low Fuel Level Indicator Light 13. Engine Management Malfunction Indicator Light zone. Engine rpm (r/min) in the red zone is above maximum recommended engine speed and is also above the range for best performance. / f&it. ::;:%M,to %:th:z 1 zone as severe engme damage may NOTE
l
SPEEDOMETER The speedometer indicates the road speed of the motorcycle. In the speedometer face are the odometer and trip meter. The odometer shows the total distance that the motorcycle has travelled. The trip meter shows the distance travelled since the meter was last reset to zero. The trip meter can be reset to zero by rotating the reset knob situated on the left hand side of the speedometer. TACHOMETER The tachometer shows the engine speed in revolutions per minute - rpm (r/min). On the right side of the tachometer face is the red
The Red Zone position for Daytona is different to that on the Speed Triple.
Page 16
General Information
COOLANT TEMPERATURE GAUGE The coolant temperature gauge indicates the temperature of the engine coolant. On the right -hand side of the gauge face is the red zone. If the temperature gauge needle moves into the red zone this indicates that the engine is overheating. HIGH BEAM: When the headlights are switched on and the headlight dip switch is set to high beam, the high beam warning light will illuminate. NEUTRAL: The neutral warning indicates when the IElI light transmission is in neutral (no gear selected). The warning light will illuminate when the transmission is in neutral with ignition switch in the ON position. LOW FUEL: The low fuel indicator ml will illuminate when there are approximately 3.7 litres of fuel remaining in the tank. ENGINE MANAGEMENT Et3 SYSTEM MALFUNCTION INDICATOR LIGHT: The malfunction indicator light for the engine management system illuminates when the ignition is switched on, remains illuminated during starting, and goes out shortly after the engine starts. If the malfunction indicator light becomes illuminated during riding, a fault has occurred in the engine management system. In this case the system will switch to limp-home mode so that riding may continue. Contact an authorised Triumph dealer as soon as possible to have the fault checked out and rectified. WARNING: Do not continue to ride for a long period with the malfunction indicator light illuminated. The fault which has occurred affect engine may performance and fuel consumption. Reduced engine performance could cause a dangerous riding condition, leading to loss of control and an accident
needle enters the red zone as severe WARNING LIGHTS a0 INDICATORS When the indicator I switch is turned to left or right, the corresponding direction indicator light flashes on and off. ~ LOW OIL PRESSURE: The low oil c l pressure warning light becomes illuminated whenever the oil pressure is dangerously low (or the ignition switch is in the ON position with the engine not running). When the engine is running, the light will remain off when sufficient oil pressure is present. When starting the motorcycle, check that the light comes on when the ignition is in the ON position, but goes out as soon as the engine starts
! CAUTION: Stop the engine if oil A immediatelylightthe low on pressure warning comes
during normal operation. Do not restart the engine until the fault has been rectified. Severe engine damage will result from running the engine when the oil warning light is illuminated.
Page 17
General Information
1. Key Number Tag IGNITION KEY In addition to operating the steering lock/ignition switch, the ignition key is required to operate the seat lock and fuel tank cap. When the motorcycle is delivered from the factory, two keys are supplied together with a small tag bearing the key number. Make a note of the key number and store the spare key and key number tag in a safe place away from the motorcycle. Your authorised Triumph dealer can supply a replacement key cut from details of the key number or can cut a new key using the original as a master.
1. 2. 3. 4. 5.
Ignition Switch/Steering Lock LOCK position OFF position ON position P (Park) position
IGNITION SWITCH/STEERING LOCK This is a four position, key operated switch. The key can be removed from the switch only when it is in the OFF, LOCK or P (PARK) position. TO LOCK: Turn the key to the OFF position, push and fully release the key, then rotate it to the LOCK position. PARKING: Turn the key from the LOCK position to the P position. The steering remains locked. NOTE:
l
Do not leave the steering lock in the P position for long periods as this will cause the battery to discharge.
Page 18
General Information
Engine off. All electrical circuits off.
1 p$ ~~ffzfi&%:,. /
lrghts on, all other electrical WARNING: For reasons of security and safety, always turn the ignition to OFF and remove the key when leaving the motorcycle unattended. Any unauthorised use of the motorcycle may cause injury to the other user, road users and pedestrians and may also cause damage to the motorcycle. WARNING: With the key in the LOCK or P position the steering will become locked. Never turn the key to Lock or P while the motorcycle is moving as the steering will lock. Locked steering will cause loss of control and an accident.
L
1. Lever Adjuster Wheel 2. Triangular Reference Mark BRAKE LEVER ADJUSTER An adjuster is fitted to the front brake lever. The adjuster allows the distance from the handlebar to the brake lever to be changed one of four positions, to suit the span of the operators hands. To adjust the lever, push the lever forward and turn the adjuster wheel to align one of the numbered positions with the triangular mark on the lever holder. The distance from the hand grip to the released lever is shortest when set to number four and longest when set to number one. WARNING: Do not attempt to adjust the brake lever with the motorcycle in motion as this may lead to loss of control and an accident. After adjusting the lever, operate the motorcycle in an area free from traffic to gain familiarity with the new lever setting. Do not loan your motorcycle to anyone as they may change the lever setting from the one you are familiar with causing loss of control or an accident.
General Information
3 Dl
Starter Button
The starter button operates the electric starter. For the starter to operate, the transmission must be in neutral and the clutch lever pulled to the handlebar. NOTE:
l
Even if the clutch lever is pulled in, the starter will not operate if the side stand is down and a gear is engaged.
1. Engine Stop Switch 2. Starter Button RIGHT HANDLEBAR SWITCHES Engine Stop Switch In addition to the ignition switch being turned to the ON position, the engine stop switch must be in the 0 position for the motorcycle to operate. The engine stop switch is for emergency use. If an emergency arises which requires the engine to be stopped, move the engine stop switch to the @ position. NOTE:
l
Although the engine stop switch stops the engine, it does not turn off all the electrical circuits. Ordinarily, the ignition switch should be used to stop the engine.
Page 20
General Information
El
High or low beam can be selected with the headlight dip switch. To select high beam, push the switch forward. To select low beam, push the switch rearwards. When the high beam is turned on, the high beam warning light will illuminate.
OO Direction Indicator Switch I When the indicator switch is pushed to 0 (left) or 0 (right) and released, the corresponding indicator flashes. 1. 2. 3. 4. 5. Headlight Dip Switch Direction Indicator Switch Horn Button Passing Button Headlight Switch To turn off the indicators, push and release the switch. Horn Button &I When the horn button is pushed, with the ignition switch turned to the ON position, the horn will sound.
0
COO:-
The headlight is turned off when the switch is in the OFF position. The side, tail, licence plate, and instrument lights come on if the switch is pushed to the first position with the ignition switch in the ON position. The head, side, tail, licence plate and instrument lights come on if the switch is pushed forward to the second position with the ignition in the ON position.
pAss Pass Button El When the pass button is pressed, the headlight main beam will be switched on. It will remain on as long as the button is held in and will turn off as soon as the button is released.
Page 21
General Information
FUEL REQUIREMENT Your Triumph engine is designed to use unleaded petrol and will give optimum performance if this fuel is used. Alwavs use unleaded fuel with an octane rating of 95 RON or higher.
countries, states or territories. Refuelling Avoid filling the tank in rainy or dusty conditions where airborne material can contaminate the fuel. 1. Ignition Switch Key 2. Fuel Tank Cap WARNING: Take care not to spill any petrol (fuel) on the engine, exhaust pipes, tyres or any other part of the motorcycle. If petrol (fuel) is spilled, thoroughly wipe off the spilled fuel immediately FUEL TANK CAP
WARNING: Petrol (fuel) is highly flammable and can be explosive under certain conditions. When refuelling, turn the ignition switch to the OFF position. Do not smoke. Make sure the refuelling area is well ventilated and free from any source of flame or sparks. This includes any appliance with a pilot light. Never fill the tank until the fuel level rises into the filler neck. If the tank is filled until the fuel rises into the filler neck, heat from sunlight or other sources may cause the fuel to expand and overflow creating a fire hazard. After refuelling, make sure the tank cap is closed securely.
To open the fuel tank cap, lift up the key hole cover. Insert the key into the lock and turn the key clockwise. To close and lock the cap, push the cap down into place, with the key inserted, until the lock clicks into place. Withdraw the key. CAUTION: Closing the cap without the kev inserted will damage the cap, tank and lock mechanism.
! A
Page 22
General Information
1. Side Stand STAND The motorcycle is equipped with a side stand on which the motorcycle can be parked. NOTE:
l
1. Seat Lock SEAT LOCK OPERATION/ SEAT REMOVAL The seat lock is situated on the left hand side of the battery box, in line with the footrest mounting rail, on the left hand side of the motorcycle. The seat is removed in two sections. The rear seat (or rear cover, where fitted) is retained by the seat lock. The front seat is held in place by two threaded fixings. To remove the rear seat/rear cover, insert the ignition key into the seat lock and turn the key anti-clockwise while pressing down on the rear part of the rear seat/rear cover. To detach the seat/rear cover, lift the rear of the seat cover and slide it away from the front seat. To refit the seat cover, engage the front section of the rear seat/rear cover under the seat bracket and press down on the rear to engage in the seat lock. NOTE:
l
When using the side stand, always turn the handlebar to the left. Whenever the side stand is used, make it a practice to ensure that the stand is fully up after first sitting on the motorcycle.
TOOL KIT The tool kit is strapped into a recess beneath the rear seat/rear cover. HANDBOOK STORAGE To gain access to the handbook, remove the seat.
An audible click can be heard when the seat/seat cover is correctly engaged in the lock.
Page 23
General Information
RUNNING-IN The first 1000 miles (1600km) that the motorcycle is ridden is designated the running-in period.
l
The table below shows maximum recommended engine speeds during running-in. These maximum speeds must be strictly adhered to during this period. Distance Travelled O-100 miles (0-160km) 100-300 miles (160-480km) 300-600 miles (480-960km) Maximum Engine Speed 3500 rpm (r/min) 5000 rpm (r/min) 6000 rpm (r/min) I 7000 rpm (r/min) 8000 rpm (r/min) I
I
Do not ride away or race the engine immediately after starting. Run the engine at idle for a short period of time to allow the oil to circulate to all parts of the engine. Do not race the engine while the transmission is in neutral. Do not use full throttle. Avoid riding continuously at one speed, vary the speed of the motorcycle from time to time. Regularly check that the coolant temperature gauge does not indicate that the engine is overheating. Stop immediately if overheating is indicated and allow the engine to cool. Do not allow the engine to labour in any gear.
Page 24
General Information
SAFE OPERATION Daily Safety Checks Check the following items each day before you ride. The time required is minimal, and these checks will help ensure a safe, reliable ride.
DAILY SAFETY CHECKS TAGLICHE SICHERHEITSKONTROLLEN CONTROLES DE SECURITE QUOTIDIENS CHEQUEQS DE SEGURIDAD DIARIOS VERIFICACOES DIAAIAS DE SEGURANCA VERIFICHE GIORNALIERE DI SICUREUA DAGELIJSKE VEILIGHEIDSINSPECTIES
If any irregularities are found during these checks, refer to the Maintenance and Adjustment section or see your authorised Triumph dealer for the action required to return the motorcycle to a safe operating condition. WARNING: Failure to perform these checks every day before you ride may result in serious motorcycle damage or an accident causing serious injury or death. Check:*
l
Fuel Adequate supply in tank, no fuel leaks (Page 22). Engine oil Correct level on sight glass. Add correct specification oil as required (Page 41). Tyres/Wheels Correct inflation pressures (when cold) (Page 58). Tread depth/wear (min 2.0 mm tread depth), tyre/wheel damage, punctures etc. Drive chain Check drive chain for correct adjustment (Page 48). Nuts, bolts, fasteners Check that steering and suspension components, axles, and all controls are properly tightened or fastened. Visually inspect all areas for loose/damaged fixings. Steering Action smooth but not loose from lock to lock. No binding of any of the control cables (Page 53). Brakes Brake pad wear: There should be more than 1.5 mm lining remaining. No brake fluid leakage. Brake fluid levels must be between max and min (Page 51). Front Forks Smooth action. No fork oil leakage (Page 54). Throttle Throttle grip play 2-3 mm. Ensure that the throttle grip returns to the idle position without sticking (Page 46). Clutch Smooth operation and correct cable free-play (Page 47).
Page 25
General Information
Coolant Electrical equipment Engine stop Sidestand Battery No coolant leakage. Check the coolant level in the expansion tank (when the engine is cold) (Page 45). All lights and horn function correctly (Page 21). Stop switch turns the engine off (Page 20). Returns to the fully up position by spring tension. Return springs not weak or damaged (Page 23). Check electrolyte level. Add distilled water as necessary (Page 62).
Page 26
28 28 29 29 30 32 33
Page 27
1. 2. 3. 4. 5.
Engine Stop Switch Starter Button Neutral Indicator Light On Position Ignition Switch
Check that the engine stop switch is in the run position. Ensure that the transmission is in neutral. Pull the clutch lever fully in to the handlebar. Turn the ignition switch on. Leaving the throttle completely closed, push the starter button until the engine starts.
. .
Close the throttle completely. Select neutral. Turn the ignition switch off. Support the motorcycle on a firm, level surface with the side stand. Lock the steering.
l l
NOTE: In very cold conditions, part open the throttle to aid starting. Return throttle to the closed position once the engine has started.
CAUTION: The engine should normally be stopped by turning the ignition switch off. The engine stop switch is for emergency
! A
poisonous and can rapidly cause loss of consciousness and death within a Always operate your motorcycle in the open-air or in an area with adequate ventilation. Page 28
! CAUTION: Do not operate the starter more A5 secondscontinuously formotor than as the starter
will overheat and battery power will drop. Wait 15 seconds between each operation of the starter to allow for cooling and recovery of battery power. Do not let the engine idle for long periods as this may lead to overheating which will cause damage to the engine. NOTE:
l
1. Gear Change Pedal CHANGING GEARS Close the throttle while pulling in the clutch lever. Change into the next higher or lower gear. Open the throttle part way, while releasing the clutch lever. Always use the clutch when changing gear. NOTE: . The gear change mechanism is the positive stop type. This means that, for each movement of the gear change pedal, you can only select each gear, one after the other, in ascending or descending order.
l
If the engine is flooded, crank the engine over, with the throttle fully open. The motorcycle is equipped with starter lockout switches. The switches prevent the electric starter from operating when the clutch is engaged and the transmission is not in neutral.
The oil ! CAUTION: warninglow light pressure A go out as soon as the engine should starts. If the low oil pressure warning light stays on after starting the engine, stop the engine immediately and investigate the cause. Running the engine with low oil pressure will cause severe engine damage. MOVING OFF
l
Pull in the clutch lever and select first gear. Open the throttle slightly and let out the clutch lever slowly. As the clutch starts to engage, open the throttle a little more, allowing enough engine speed to avoid stalling.
WARNING: Do not change to a lower gear at speeds which will cause excessive engine rpm (r/min). This can lock the rear wheel causing loss of control and an accident. Engine damage may also be caused. Changing down should be done below 5000 rpm (r/min) for each gear.
Page 29
1. Rear Brake Pedal WARNING: For emergency braking, disregard down changing, and concentrate on applying the front and rear brakes as hard as possible without skidding. Riders should practice emergency braking in a traffic-free area. Triumph strongly recommend that all riders take a course of instruction which includes advice on safe brake operation. Incorrect brake technique could result in loss of control and an accident.
Close the throttle completely, leaving the clutch engaged to allow the engine to help slow down the motorcycle. Change down one gear at a time such that the transmission is in first gear when the motorcycle comes to a complete stop. When stopping, always apply both brakes at the same time. Normally the front brake should be applied a little more than the rear. Change down or fully disengage the clutch as necessary to keep the engine from stalling. Never lock the brakes, as this may cause loss of control of the motorcycle and an accident.
Page 30
WARNING: When descending a long, steep gradient use engine braking by down-changing and use the brakes intermittently. Continuous brake application can overheat the brakes and reduce their effectiveness. Riding with your foot on the brake pedal or your hands on the brake lever may actuate the brake light, giving a false indication to other drivers. It may also overheat the brake, reducing braking effectiveness. Do not coast with the engine switched off, and do not tow the motorcycle. T h e t r a n s m i s s i o n i s pressurelubricated only when the engine is running. Inadequate lubrication may cause damage or seizure of the transmission which can lead to sudden loss of motorcycle control and an accident.
Page 31
PARKING Select neutral and turn the ignition switch to the OFF position. Always park on a firm, level surface to prevent the motorcycle from falling. When parking on a hill, always park facing uphill to prevent the motorcycle from rolling off the stand. On a lateral (sideways) incline, always park with the motorcycle leaning towards the sidestand and engage first gear to prevent the motorcycle from moving. Do not park on a lateral (sideways) incline of greater than 6 and never park facing downhill. Lock the steering to help prevent theft. NOTE:
l
When parking near traffic at night, leave the tail, licence plate and side lights on by turning the ignition switch to P (Park). Do not leave the switch in the P position for long periods as this will discharge the battery.
Page 32
WARNING: The items listed are extremely important and must never be neglected. A problem which may not be noticed at normal operating speeds may be greatly exaggerated at high speeds.
I
the valve caps after checking tyre pressures. Observe the information given in maintenance and specification sections on tyre checking and tyre safety. Fuel
1
WARNING: The handling of a characteristics motorcycle at high speed may vary from those you are familiar with at legal road speeds. Do not attempt high speed operation unless you have received sufficient training and have the required skills as a serious accident may result from incorrect operation.
Have sufficient fuel for the higher consumption experienced during high speed operation. Engine Oil Make certain that the oil level is visible mid-way up the sight glass. Ensure that the correct grade and type of oil is used when topping-up. Coolant Check that the coolant level is at the upper level line in the expansion tank. (Always check level with engine cold). Electrical Equipment Make certain that the headlight, rear/brake light, turn signals, horn etc., all work properly. Miscellaneous Make certain that all fixings are tight and that all safety related parts are in good condition.
Page 3 3
authorised closed course conditions. WARNING: The handling and braking capabilities of a motorcycle will be affected by the presence of a passenger. The rider must make allowances for these changes when operating the motorcycle with a passenger. Motorcycle operation without making allowances for the presence of a passenger could lead to loss of motorcycle control and an accident.
Page 34
Single seat WARNING: models must never carry a passenger unless a passenger seat is fitted. Carrying a passenger without first fitting a passenger seat will contravene the law and may also cause loss of motorcycle control leading to an accident. WARNING: Your passenger should be thoroughly familiar with motorcycle operation. The passenger can cause loss of control of the motorcycle by incorrect positioning during cornering and sudden movements. It is important that the passenger sits still while the motorcycle is in motion and does not interfere with the operation of the motorcycle. If a passenger is carried, the rider should instruct the passenger to keep his or her feet on the passenger footrests and to firmly hold onto the seat strap or the riders waist or hips. The passenger should also be advised to lean with the rider when travelling in corners and not to lean unless the rider does so. Do not carry animals on your motorcycle.
WARNING: Do not carry a passenger unless he or she is tall enough to reach the footrests provided. A passenger who is not tall enough to reach the footrests will be unable to sit securely on the motorcycle and may cause instability leading to loss of control and an accident. WARNING: Never attempt to store any items between the frame and the fairing. This can restrict the steering and will cause loss of control leading to an accident, Weight attached to the handlebar OI front fork will increase the mass of the steering assembly and can result in loss of steering control leading to an accident.
Page 35
Page 36
Rear Suspension Adjustment T y r e s Battery................ Windscreen Cleaning Fuses .._.... Headlights - Daytona Headlights - Speed Triple R e a r L i g h t Licence Plate Light Indicator Light . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . .
Page 37
Engine o i l - renew
Cooling system -check for leaks Fuel system -check for leaks Fuel Filter - renew Steering - check for free operaton
Day Day
0 0
0 0
l l
0 0
Day
Page 38
I
Operation Description
Headstock bearing -check/adjust Headstock bearing - lubricate Forks-check for leaks/smooth operation Fork o i l - renew Brake fluid levels-check Day
Day
l l
l l
l
Every 2 years
Brake hoses -renew Brake light-check operation Brake pads - check wear levels Brake master cylinder - renew seals Brake calipers - renew seals Drive chain - lubricate Drive chain -wear check Drive chain slack - check/adjust Rear suspension - lubricate
I
I
1
I
l l
l
l
l
l
l
l
l
l
l
l
Every 2 years Every 2 years Every 200 miles (300 kms) Every 500 miles (800 kms) Day
Page 39
Remove the seat(s). Disconnect the battery, negative (black) lead first. Release the fixings as shown in the diagram above. Disconnect the rear light. Lift and withdraw the side panel assembly in a rearward direction. Reverse the removal procedure with the exception of the following. Reconnect the battery positive (red) lead first. Tighten the panel fixings to 9 Nm.
.
l
Page 40
Stop engine, then wait for at least 10 minutes to allow the oil to settle. The oil level is indicated by a sight glass situated at the bottom of the clutch cover on the right hand side of the motorcycle. When the oil level is correct, the level of oil should be between the two lines marked on the clutch cover to the right of the sight glass.
In order for the engine, transmission, and clutch to function correctly, maintain the engine oil at the correct level, and change the oil and oil filter in accordance with scheduled maintenance requirements. WARNING: Motorcycle operation with insufficient, deteriorated, or contaminated engine oil will cause accelerated engine wear and may result in engine or transmission seizure. Seizure of the engine or transmission may lead to loss of control and an accident.
NOTE: The actual level is indicated when the motorcycle is level and upright, not on the side stand. If the oil level is too low, remove the plug situated in the upper rear side of the clutch cover. Add oil, a little at a time, until the oil begins to show in the sight glass. Then adjust to the correct level and refit the plug.
Page 41
1. Oil Drain Plug 2. Oil Filter Oil and Oil Filter Change WARNING: Prolonged or repeated contact with engine oil can lead to skin dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contamination which can cause cancer. Wear suitable clothing and avoid skin contact. The engine oil and filter must be replaced in accordance with scheduled maintenance requirements.
l
Warm up the engine thoroughly, and then stop the engine. Place an oil pan beneath the engine. Remove the engine drain plug.
Page 4 2
Ensure that the oil pressure warning light extinguishes shortly after starting.
! CAUTION: Triumph high fuel A performance to useinjected engines are designed semi or
fully synthetic 10W/40 motorcycle engine oil which meets specification API SH. Do not add any chemical additives to the engine oil. The engine oil also lubricates the clutch and any additives could cause the clutch to slip. Do not use mineral, vegetable, non-detergent oil, castor based oils or any oil not conforming to the required specification. The use of these oils may cause instant, severe engine damage. Ensure no foreign matter enters the crankcase during an oil change or top-up.
CAUTION: If the engine oil ! A pressure is too low, the low oil pressure warning light will illuminate. If this light stays on when the engine is running, stop the engine immediately and investigate the cause. Running the engine with low oil pressure will cause engine damage.
l
Stop the engine and check the oil level. Adjust if necessary.
Disposal of Used Engine Oil To protect the environment, do not pour oil on the ground, down sewers or drains, or into water courses. Dispose of used oil sensibly. If in doubt contact your local authority.
Page 43
CAUTION: Using high ! pressure water, such as from a car wash facility, can damage the radiator fins and impair the radiators efficiency. Do not obstruct or deflect airflow through the radiator by installing unauthorised accessories, either in front of the radiator or behind the cooling fan. Interference with the radiator airflow can cause overheating, resulting in engine damage.
Page 44
If the coolant level is being checked because the coolant has overheated, also check the level in the radiator and top-up if necessary. In an emergency, water alone can be added to the cooling system. However, the coolant must be returned to the correct mixture ratio as soon as possible.
1. 2. 3. 4.
Distilled water CAUTION: must be used with the antifreeze (see specification for antifreeze) in the cooling system.
! A
A PI
WARNING: Do not remove the radiator cap when the engine is hot. When the engine is hot, the coolant inside the radiator is hot and also under pressure. Contact with this hot, pressurised coolant will cause scalds and skin damage.
l
If hard water is used in the system, it causes scale accumulation in the water passages, and considerably reduces the efficiency of the cooling system. If coolant must be added often, or the expansion tank runs dry, there is probably a leak in the system. Have the cooling system inspected by your authorised Triumph dealer.
Position the motorcycle on level ground and in an upright position. Remove the seat. Check the coolant level in the expansion tank. The coolant level must be between the MAX and MIN marks. If the level of coolant is too low, remove the cap from the expansion tank, and add coolant mixture through the filler opening to the MAX mark. Refit the cap. Page 45
1. Throttle Grip 2 . 2-3mm 3. Upper Adjuster Locknut 4. Adjuster THROTTLE GRIP The throttle grip controls the throttle valves in the throttle bodies. If the throttle cable is incorrectly adjusted, either too tight or too loose, the throttle may be difficult to control and performance will be adversely affected. Check the throttle grip free-play in accordance with scheduled maintenance requirements and make adjustments as necessary. Inspection
l
cable could interfere with the throttle function resulting in loss of control of the motorcycle and an accident. Adjustment NOTE: Minor adjustments can be made using the adjuster near the twist grip end of the throttle. Where a correct setting cannot be achieved in this way, the adjuster at the throttle body end must be used. Disconnect the battery negative (black) lead first. Set the cable adjuster at the twist grip end such that it has an equal amount of adjustment in each direction.
Check that there is 2-3 mm throttle grip free-play when lightly turning the throttle grip back and forth. If there is an incorrect amount of free-play, adjustments must be made.
Page 46
Set the adjuster at the throttle body end of the cable to give 2-3 mm of play at the twist grip. Tighten the locknut. Make any minor adjustments as necessary to give 2-3 mm of play using the adjuster at the twist grip end of the cable. Tighten the locknut.
WARNING: Ensure that both the adjuster locknuts are tightened. A loose throttle cable adjuster could cause the throttle to stick leading to loss of control and an accident.
l
1. Lever 2. 0.4-0.8 mm Adjustment Loosen the knurled locknut at the lever end of the clutch cable and turn the adjuster sleeve until the correct amount of clutch lever free-play is achieved. Tighten the knurled locknut against the clutch lever assembly. If correct adjustment cannot be made using the lever adjuster, use the cable adjuster at the lower end of the cable. Loosen the adjuster locknut. Turn the outer cable adjuster to give 0.4-0.8 mm of free-play at the clutch lever. Tighten the locknut.
Reconnect the battery, positive (red) lead first. Refit the seat.
CLUTCH The motorcycle is equipped with a cable operated clutch. If the clutch lever has excessive free-play, the clutch may not disengage fully and cause difficulty in changing gear and clutch drag. Conversely, if the clutch lever has insufficient free-play the clutch may not engage fully, causing clutch slip. Clutch lever free-play must be checked in accordance with scheduled maintenance requirements. Inspection
l
Check that there is 0.4-0.8 mm clutch lever free-play as shown in the diagram above. If there is an incorrect amount 01 free-play, adjustments must be made.
Page 47
For safety and to prevent excessive wear, the drive chain must be checked, adjusted, and lubricated in accordance with scheduled maintenance requirements. Checking, adjustment and lubrication must be carried out more frequently for extreme conditions such as salty or heavily gritted roads. If the chain is badly worn or incorrectly adjusted (either too loose or too tight) the chain could jump off the sprockets or break.
sprockets could snag on the engine sprocket or lock the rear wheel, severely damaging the motorcycle Never neglect chain maintenance. NOTE: l Checking, adjustment and lubrication of the drive chain must be carried out with the motorcycle set up on a paddock stand so that the rear suspension hangs free. Chain Free-movement Inspection WARNING: To prevent risk of injury from the motorcycle falling during the inspection, ensure that the motorcycle is stabilized and secured on the stand.
l
chain free-movement If the incorrect, measurement is adjustments must be made as follows: Loosen the clamp bolt which secures the rear hub/eccentric adjuster to the swinging arm. Using the C spanner supplied in the motorcycle tool kit, turn the rear hub/eccentric adjuster (clockwise to loosen, anti-clockwise to tighten) until the drive chain is correctly adjusted (35-40 mm of vertical movement). Tighten the rear hub/eccentric adjuster clamp bolt to 55 Nm. Rotate the rear wheel and repeat the chain adjustment check. Re-adjust if outside the 35-40 mm limit.
Rotate the rear wheel to find the position where the chain is tightest, and measure the vertical movement of the chain midway between the sprockets. The vertical movement of the drive chain must be 35-40 mm.
Puge 48
I
1. Adjuster Clamp Bolt 2. C Spanner 3. Eccentric Adjuster WARNING: Operation of the motorcycle with an insecure rear hub/eccentric adjuster clamp bolt may result in impaired stability and handling of the motorcycle. This impaired stability and handling may lead to loss of control or an accident.
l
Stretch the chain taut by hanging a 10-20 kg (20-40 lb) weight on the chain. Measure the length of 20 links on the straight part of the chain from pin centre of the 1 st pin to the centre of the 21st pin. Since the chain may wear unevenly, take measurements at several places. If the length exceeds the maximum service limit of 319 mm, the chain must be replaced.
WARNING: A chain that breaks or jumps off the sprockets could snag on the engine sprocket or lock the rear wheel, severely damaging the motorcycle and causing loss of control and an accident.
Page 49
If there is any irregularity, have the drive chain and/or the sprockets replaced by an authorised Triumph dealer. Replace the chain guard.
w-w
Chain Lubrication
, Lubrication necessary every 500 miles and also after riding in wet weather, on wet roads, or any time that the chain appears dry.
Use the special chain lubricant as recommended in the specification section.
l
NOTE:
l
The use of WARNING: non-approved chains may result in a broken chain or may cause the chain to jump off the sprockets.
A
Apply lubricant to the sides of the rollers. This will allow the oil to penetrate to the chain rollers and bushings. Also apply oil to the chain 0 rings. Wipe off any excess oil. If the chain is especially dirty, clean first using paraffin and then apply oil as mentioned above.
Use a genuine Triumph supplied chain as specified in the Triumph Parts Catalogue. Never neglect chain maintenance and always have chains installed by an authorised Triumph dealer.
l
CAUTION: Do not use a ! A power jet wash to clean the chain as this may cause damage to the chain components.
Rotate the rear wheel and inspect the drive chain for damaged rollers, and loose pins and links. Also inspect the sprockets for unevenly or excessively worn or damaged teeth.
Page 50
1. Lining Thickness 2. 1.5 mm (0.06 in) Groove Thickness BRAKES Brake Wear Inspection Brake pads must be inspected in accordance with scheduled requirements and replaced if worn to, or beyond the minimum service thickness. If the lining thickness of any pad (front or rear brakes) is less than 1.5 mm (0.06 in), that is, if the pad has worn down to the bottom of the grooves, replace all the pads on the wheel. WARNING: Brake pads must always be replaced as a wheel set. At the front, where two calipers are fitted on the same wheel, replace all the brake pads in both calipers. Replacing individual pads will reduce braking efficiency and may cause an accident.
Page 51
1. Upper Level, Front Brake 2. Lower Level, Front Brake 3. Safety Clip Brake Fluid Level Inspection and Adjustment l The brake fluid level in the reservoirs must be kept between the upper and lower level lines (reservoir held horizontal). l At the rear, remove the side panel assembly. l Remove the safety clip (front only). . Fill the reservoir to the upper level line using new DOT 4 fluid from a sealed container. . Refit the reservoir cap ensuring that the diaphragm seal is correctly fitted. l Refit the safety clip. l At the rear, refit the side panels. WARNING: If there has been an appreciable drop in the level of the fluid in any fluid reservoir, consult your authorised Triumph dealer for advice before riding. Riding with defective brakes may lead to an accident.
1. Upper Level, Rear Brake 2. Lower Level, Rear Brake Brake Pad Wear Compensation Disc and disc pad wear is automatically compensated for and has no effect on the brake lever or pedal action. There are no parts that require adjustment on the front and rear brakes. WARNING: If the brake lever or pedal feels soft when it is applied, or if the lever/pedal travel becomes excessive, there may be air in the brake lines or the brake may be defective. It is dangerous to operate the motorcycle under such conditions and remedial action must be taken by your authorised Triumph dealer before riding. Riding with defective brakes may lead to an accident.
Page 52
Inspecting the Steering for Free-Play Inspection Position the motorcycle on level ground, in an upright position. Remove the belly panel (where fitted). Raise the front wheel off the ground and place a block beneath the engine to support the motorcycle. Hold the lower end of the front forks and try to move them forward and backward. If any free-play can be detected, ask your authorised Triumph dealer to inspect and rectify any faults before riding.
Leaving the support in place, inspect the wheel bearings as described over.
Page 53
FRONT SUSPENSION All models are fitted with forks which are adjustable for spring pre load, compression damping and rebound damping. Front Fork Inspection
l
Examine each fork stanchion for any sign of damage, scratching of the slider surface, or for oil leaks. If any damage or leakage is found consult an authorised Triumph dealer.
Gently rock the top of the front wheel from side to side. If any free-play can be detected, ask your authorised Triumph dealer to inspect and rectify any faults before riding. Reposition the lifting device and repeat for the rear wheel.
Position the motorcycle on level ground. While holding the handlebars and applying the front brake, pump the forks up and down several times.
WARNING: Operation with worn or damaged wheel bearings may cause impaired handling and instability leading to an accident. If in doubt, have the inspected by an motorcycle authorised Triumph dealer before riding. .
l
NOTE:
l
The suspension movement will be affected by adjustment settings. If roughness or excessive stiffness is detected, consult your authorised Triumph dealer.
Remove the support and place the motorcycle on the side stand. Refit the belly panel (where fitted).
Page 54
* Number of adjuster turns out from the fully screwed in position. NOTE: This chart is only a guide. Setting requirements may vary for rider weight and personal preferences. See the following pages for details of how to adjust your suspension. Front Suspension Settings The standard suspension settings provide a comfortable ride and good handling characteristics for general, solo riding. The chart shows suggested settings for front and rear suspension. WARNING: Ensure that the correct balance between front and rear suspension is maintained. could Suspension imbalance handling significantly change characteristics leading to loss of control and an accident. Refer to the chart above for further information or consult your Triumph dealer. The spring pm-load and rebound damping adjusters are located in the top of each fork. The compression damping adjuster is located near the bottom of each fork, adjacent to the wheel spindle. setting on both forks. Settings which affect handling resulting in loss of
NOTE:
l
The setting figures above/over are all measured as adjuster turns out from the fully screwed in position.
Page 55
1. Spring Pre-load Adjuster 2. Rebound Damping Force Adjuster Spring Pm-load Adjustment To change the spring pre-load, rotate the adjuster clockwise (screw-in) to increase pre-load, or anti-clockwise (screw-out) to decrease pre-load. Always set the pre-load adjusters such that there are an equal number of graduation lines visible on both forks. NOTE:
l
3. Compression Adjuster
Damping
Force
NOTE: l The motorcycle is delivered from the factory with the compression damping set at position 1. Rebound Damping Adjustment To change the rebound damping force, rotate the slotted adjuster clockwise (screw-in) to increase, or anti-clockwise (screw-out) to decrease. Always count the turns out from the screwed fully in position and set both forks to the same position. Maximum damping force is obtained when the adjuster is rotated fully clockwise (screwed fully in). Minimum damping force is obtained when the adjuster is rotated fully anti-clockwise (screwed fully out). NOTE:
l
The motorcycle is delivered from the factory with the spring pre-load set on position 5.
Compression Damping Adjustment To change the compression damping force rotate the slotted adjuster clockwise (screw-in) to increase, or anti-clockwise (screw-out) to decrease. Maximum damping force is obtained when the adjuster is rotated fully clockwise (screwed fully in). Minimum damping force is obtained when the adjuster is rotated fully anti-clockwise (screwed fully out). Always count the turns out from the screwed fully in position and set both forks to the same setting.
The motorcycle is delivered from the factory with the rebound set at position 1.
Page 56
1. Rebound Damping Adjuster REAR SUSPENSION ADJUSTMENT The rear suspension unit is adjustable for both compression and rebound damping. Rebound Damping Adjustment The rebound damping adjuster is situated at the lower left hand end of the rear suspension unit. To adjust the rebound damping setting, rotate the adjuster clockwise to increase rebound damping and anti-clockwise to decrease. NOTE
l
1. Compression Damping Adjuster Compression Damping Adjustment The compression damping adjuster is situated on the rear suspension unit reservoir. To adjust the compression damping setting, rotate the slotted adjuster clockwise (screw-in) to increase, or antiilockwise (screw-out) to decrease. NOTE:
l
The motorcycle is delivered from the factory with the compression damping set at 1.
The settings are all measured as the number of adjuster turns out from the fully screwed in position. The motorcycle is delivered from the factory with the rebound adjuster set to position 1.
WARNING: Rear suspension unit spring pm-load is not rider adjustable. Any attempt to adjust the spring pre-load could result in a dangerous riding condition leading to loss of control and an accident.
Page 57
Wheel Marking WARNING: Incorrect tyre inflation will cause abnormal tread wear and instability problems which may lead to loss of control and an accident. Under-inflation may result in the tyre slipping on, or coming off the rim. Over-inflation will cause instability and accelerated tread wear. Both conditions are dangerous as they may cause loss of control leading to an accident.
TYRES This motorcycle is equipped with tubeless tyres, valves and wheel rims. Use only tyres marked TUBELESS and tubeless valves on rims marked SUITABLE FOR TUBELESS TYRES. Tyre Inflation Pressures Correct inflation pressure will provide maximum stability, rider comfort and tyre life. Always check tyre pressures before riding when the tyres are cold. Check tyre pressures daily and adjust if necessary. See the specification section for details of the correct inflation pressures.
Page 58
Tyre Wear As the tyre tread k!!??@! wears down, the tyre becomes more susceptible to punctures and failure. It is estimated that 90% of all tyre failures occur during the last 10% of tread life (90% worn). It is, therefore, false economy and unsafe to use tyres until they are worn to their minimum.
l
In accordance with the periodic maintenance chart, measure the depth of the tread with a depth gauge, and replace any tyre that has worn to the minimum allowable tread depth.
WARNING: This motorcycle must not be operated above the legal road speed limit except in authorised closed course conditions.
Page 59
WARNING: Do not install tube-type tyres on tubeless rims. The bead will not seat and the tyres could slip on the rims, causing rapid tyre deflation that may result in a loss of vehicle control and an accident. Never install an inner tube inside a tubeless tyre. This will cause friction inside the tyre and the resulting head build-up may cause the tube to burst resulting in rapid tyre deflation, loss of vehicle control and an accident.
Page 60
WARNING: Accurate wheel balance is necessary for safe, stable handling of the motorcycle. Do not remove or change any wheel balance weights., Incorrect wheel balance may cause instability leading to loss of control and an accident. When wheel balancing is required, such as after tyre replacement, see your authorised Triumph dealer. Only use self-adhesive weights. Clip on weights may damage the wheel and tyre resulting in tyre deflation, loss of control and an accident.
Page 61
BATTERY IAIQ 4
WARNING: The battery gives off explosive gases; keep sparks, flames and cigarettes away. Provide adequate ventilation when charging or using the battery in an enclosed space. The battery contains sulphuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear protective clothing and a face shield. - If electrolyte gets on your skin, flush with water immediately. - If electrolyte gets in your eyes, flush with water for at least 15 minutes and SEEK MEDICAL ATTENTION IMMEDIATELY. - If electrolyte is swallowed, drink large quantities of water and SEEK MEDICAL ATTENTION IMMEDIATELY. KEEP ELECTROLYTE OUT OF THE REACH OF CHILDREN. WARNING: The battery contains harmful materials. Always keep children away from the battery whether or not it is fitted in the motorcycle. Do not jump start the battery, touch the battery cables together or reverse the polarity of the cables as any of these actions may cause a spark which would ignite battery gases causing a risk of personal injury.
1. Battery 2. Negative Terminal 3. Positive Terminal Battery Disposal Should the battery ever require replacement, the battery must be handed to a recycling agent who will ensure that the dangerous substances from which the battery is manufactured to not pollute the environment. Battery Removal . Remove the front seat
l
Remove the battery strap and disconnect the breather tube. Disconnect the battery leads, negative (black) lead first. Take the battery out of the case.
the motorcycle frame as this may would ignite battery gases causing a
Page 62
If the electrolyte level is low in any cell, fill with distilled water as follows: Remove the battery filler caps and fill with distilled water until the electrolyte level in each cell reaches the upper level line. Replace the caps.
.2
-3
.
CAUTION: When checking the battery electrolyte level, or adding distilled water, ensure that the breather tube is not blocked. 1. Filler Caps 2. Upper Level 3. Lower Level 4. Breather Tube Connection
l
Use only distilled water in the battery. Tap water will shorten the service life of the battery. Filling the battery above the UPPER LEVEL line may cause the electrolyte to overflow, resulting in corrosion to engine or nearby parts. Immediately wash off any spilled electrolyte.
Clean the battery using a clean, dry, Be sure that the cable cloth. connections are clean.
Battery Electrolyte Level Inspection WARNING: The battery electrolyte is corrosive and poisonous and will cause damage to unprotected skin. Never swallow battery electrolyte or allow it to come into contact with the skin. To prevent injury, always wear eye and skin protection when adjusting the electrolyte level. The battery electrolyte level must be kept between the upper and lower level lines. Check the electrolyte level in each cell in accordance with scheduled requirements.
l
to prevent restrictions in the tube. Do bent or kinked breather tube may pressurise the battery and damage its
Remove the battery from the motorcycle. Check that the electrolyte level in each cell is between the upper and lower level lines.
Page 63
Page 64
a
9 10 NOTE:
l
The fuse identification numbers listed above correspond with those printed on the fuse box cover.
Page 65
1. Vertical Adjustment Screw (LH) 2. Horizontal Adjustment Screw (LH) HEADLIGHTS - DAYTONA WARNING: Adjust road speed to suit the visibility and weather conditions in which the motorcycle is being operated. Ensure that the beam is adjusted to illuminate the road surface sufficiently far ahead without dazzling oncoming traffic. An incorrectly adjusted headlight may impair visibility causing an accident. WARNING: Never attempt to adjust the headlamp beam when the motorcycle is in motion. Any attempt to adjust the headlamp beam when the motorcycle is in motion may result in loss of control and an accident.
1. Vertical Adjustment Screw (RH) 2. Horizontal Adjustment Screw (RH) Headlight Adjustment Each headlight can be adjusted by means of vertical and horizontal adjustment screws located on the rear of the headlight unit. Switch the headlight dipped beam on. Turn the vertical adjustment screw on each headlight clockwise to lower the beam or anti-clockwise to raise the beam. On the RH headlight turn the horizontal adjustment screw clockwise to move the beam to the right or anti-clockwise to move the beam to the left. On the LH headlight turn the horizontal adjustment screw anti-clockwise to move the beam to the right or clockwise to move the beam to the left. Switch the headlights off when the beam settings are satisfactory.
Page 66
1. Headlight Unit 2. Side Fixing (RH) 3. Centre Fixing Headlight Bulb Replacement The complete headlight unit must be removed to gain access for bulb replacement. Remove the seat(s). Disconnect the battery, negative (black) lead first. Remove the cockpit. Unscrew the nuts securing the headlight unit to the support bracket and release the unit. Disconnect the multi-pin electrical connector from the bulb to be replaced and remove the rubber cover. Detach the wire bulb retainer from the clip. It is not necessary to undo the screw. Remove the bulb from the headlight unit. Installation is the reverse of the removal procedure.
1. Bulb Retainer
becomes hot during use. Always allow sufficient time for the bulb to cool before handling. Avoid touching the glass part of the bulb. If the glass is touched or gets dirty, clean with alcohol before re-use. Position Lamp Bulb Replacement The position lamp is fitted to the cockpit above the headlight aperture. Remove the cockpit panel to gain access for bulb replacement.
Page 67
1. Vertical Adjustment Clamp HEADLIGHTS - SPEED TRIPLE WARNING: Adjust road speed to suit the visibility and weather conditions in which the motorcycle is being operated. Ensure that the beam is adjusted to illuminate the road surface sufficiently f a r a h e a d w i t h o u t dazzling oncoming traffic. An incorrectly adjusted headlight may impair visibility causing an accident. The horizontal beam of each headlight can be adjusted individually. The vertical beams are adjusted as a pair.
2. Horizontal Adjustment Clamp Headlight Adjustment Switch the headlight dipped beam on. Partially release the central clamp fixing on the headlight mounting bracket and pivot both headlights upward or downward as necessary. Tighten the central clamp fixing while holding the headlights in the desired position. Release the clamp fixing to the rear of the headlight bowl and pivot the headlamp to the left or right as necessary. Tighten the clamp fixing while holding the headlight in the desired position. Repeat for the other headlight. Switch the headlights off when the beam settings are satisfactory.
Page 68
A A
Page 69
1. Rear Light Bulb Retainer REAR LIGHT Bulb Replacement-All Models . Remove the rear seat/cover to gain access to the tail light unit. .
l
1. Indicator Lens 2. Securing Screw INDICATOR LIGHT Bulb Replacement-All Models The lens on each indicator light is held in place by a securing screw located in the body of the light. . Release the screw and remove the amber lens to gain access to the bulb for replacement.
Rotate the bulb holder anti-clockwise to release. Replace the bulb. Fit the bulb holder to the tail light unit. Refit the seat/cover
Remove the side panels to gain access to the licence plate light unit. Carefully remove the rubber bulb holder from the back of the light unit.
! CAUTION: To avoid cable damage, A using the do not pull the bulb holder cables.
l
Replace the bulb. Fit the bulb holder to the light unit. Refit the seat/cover.
Page 70
Where to be Careful Avoid spraying water with any great force near the following places: .
l
Instruments. Brake cylinders and brake calipers. Under the fuel tank. Drive chain and headstock bearings.
NOTE:
l
Coin operated, high pressure washers are not spray recommended. The water may be forced into bearings and other components causing eventual failure from rust and corrosion. Some of the soaps which are highly alkaline leave a residue or cause spotting.
After Washing Remove the plastic bags and tape, and clear the air intakes. Lubricate the pivots, bolts and nuts. Test the brakes before motorcycle operation. Start the engine and run it for 5 minutes. Ensure adequate ventilation for the exhaust fumes. Use a dry cloth to absorb water residue. Do not allow water to stand on the machine as this will lead to corrosion.
Rear opening of the muffler: Cover with a plastic bag secured with rubber bands. Clutch and brake levers, switch housings on the handlebar: Cover with plastic bags. Ignition switch: Cover the keyhole with tape. Air cleaner intakes: Close up the intakes with tape.
Page 71
Wash the exhaust system with a soft Do not use an abrasive cloth. scouring pad or steel wool. They will damage the finish. Rinse the thoroughly. exhaust system
Ensure no soap or water enters the mufflers. Dry the exhaust system completely with a soft cloth. Do not run the engine to dry the system or spotting will occur. When the exhaust system is dry, rub Motorex 645 Clean And Protect into the surface.
Items such as brake and clutch levers must be correctly cleaned to preserve their appearance. Use a proprietary brand of aluminium cleaner which does not contain abrasive or caustic elements. Clean aluminium items regularly, in particular after use in inclement weather, where the components must be hand washed and dried each time the machine is used. Warranty claims due to inadequate maintenance will not be allowed.
Drying
l
Protecting
l
Cleaning of the Exhaust System: All parts of the exhaust system of your motorcycle must be cleaned regularly to avoid a deterioration of its appearance. These instructions can be applied to black chrome, brushed stainless steel and carbon fibre components alike. NOTE:
l
The of silicone ! CAUTION:suchuse WD40 will products as A discolouration of the chrome cause and must not be used. Similarly, the use of abrasive cleaners such as Solvol Autosol will damage the system and must not be used.
l
It is recommended that regular protection be applied to the system as this will both protect and enhance the systems appearance.
The exhaust system must be cool before washing to prevent water spotting. Prepare a mixture of water and mild soap. Do not use a high alkaline content soap as commonly found at commercial car washes because it leaves a residue.
Washing
l
Page 72
Storage
Preparation for Storage:
l
Clean the entire vehicle thoroughly. Empty the fuel from the fuel tank into a secure container.
cold weather so that the electrolyte does not freeze and crack the battery. The more discharged the battery becomes, the more easily it freezes.
l
Petrol WARNING: is extremely flammable and can be certain explosive under conditions. Turn the ignition switch OFF. Do not smoke. Make sure the area is well ventilated and free from any source of flame or sparks; this includes any appliance with a pilot light.
l
Tie plastic bags over the exhaust pipe to prevent moisture from entering. Put a cover over the motorcycle to keep dust and dirt from collecting on it.
Preparation after Storage: Check the electrolyte level in the battery, c h a r g e t h e b a t t e r y i f necessary, and install it in the motorcycle. Be careful that the battery vent hose is not pinched and that it is routed as shown on the label. Fill the fuel tank with fuel. Change the engine oil and filter. Check all the points listed in the Daily Safety Checks section. Before starting the engine, remove spark plugs. Put side stand down. This will isolate the ignition and prevent stray sparks and damage to the ignition system. Crank the engine on the starter motor several times until the oil pressure light goes out. Replace spark plugs and start engine. Check brakes and operation.
Remove the spark plugs and put several drops (5 ml) of engine oil into each cylinder. Push the starter button for a few seconds to coat the cylinder walls with oil, and install the spark plugs. Reduce tyre pressure by about 20%. Set the motorcycle on a box or stand so that both wheels are raised off the ground. (If this cannot be done, put boards under the front and rear wheels to keep dampness away from the tyre rubber). Spray oil on all unpainted metal surfaces to prevent rusting. Prevent oil from getting on rubber parts, brake discs or in the brake calipers. Lubricate the drive chain and all the control cables. Remove the battery, and store it where it will not be exposed to direct sunlight, moisture, or freezing temperatures. During storage it should be given a slow charge (one ampere or less) about once a month. Keep the battery well charged during
Page 73
Specifications
DAYTONA PERFORMANCE Maximum Power . . . . . . . . . . . . . . . . . . . 130 PS @ 10200rpm (r/min) Maximum Torque . . . . . . . . . . . . . . . . . . . 100.0 Nm @ 8500rpm (r/min) DIMENSIONS 2115mm 800mm 1170mm 1440mm 800mm 198kg 185kg 108 PS @ 9100rpm (r/min) 85.0 N m @ 7500rpm (r/min) 2115mm 860mm 1230mm 1440mm 800mm 196kg 185kg SPEED TRIPLE
Overall Length . . . . . . . . . . . . . . . . . . . . . Overall Width (to mirrors) . . . . . . . . . . . . Overall Height . . . . . . . . . . . . . . . . . . . . . Wheelbase . . . . . . . . . . . . . . . . . . . . . . . . Seat Height . . . . . . . . . . . . . . . . . . . . . . . . Dry Weight
........................
Maximum Payload . . . . . . . . . . . . . . . . . . (rider & passenger & accessories) ENGINE Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displacement . . . . . . . . . . . . . . . . . . . . . . Bore x Stroke . . . . . . . . . . . . . . . . . . . . . . Compression Ratio . . . . . . . . . . . . . . . . . Cylinder Numbering . . . . . . . . . . . . . . . . . Sequence . . . . . . . . . . . . . . . . . . . . . . . . . Firing Order . . . . . . . . . . . . . . . . . . . . . . . Starting System . . . . . . . . . . . . . . . . . . . . LUBRICATION Lubrication System . . . . . . . . . . . . . . . . .
in-line 3 cyl. 955cc 79x65mm 11.2:1 Left to Right l-2-3 1-2-3 Electric Starter
in-line 3 cyl. 885cc 76x65mm 11.0:1 Left to Right l-2-3 l-2-3 Electric Starter
Forced Lubrication (wetsump) Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . Semi or fully synthetic 1OW/40 motorcycle engine oil which meets API SH specification 4.00 litres
Forced Lubrication (wetsump) Semi or fully synthetic 1OWl40 motorcycle engine oil which meets API SH specification 4.00 litres
Page 74
Specifications
DAYTONA COOLING C o o l a n t T y p e Mobil Antifreeze 50/50 2.0 litre 85C SPEED TRIPLE Mobil Antifreeze 50/50 2.0 litre 85C
Electronic Fuel Injection Twin Pencil Solenoid Operated Plate Valve Submerged Electric 3 Bar
Electronic Fuel Injection Twin Pencil Solenoid Operated Plate Valve Submerged Electric 3 Bar
P r e s s u r e
..__._.._ C a p a c i t y
I g n i t i o n
S y s t e m
Page75
Specifications
DAYTONA TRANSMISSION Transmission Type C l u t c h P r i m a r y F i n a l T y p e D r i v e D r i v e 6 Speed, Constant Mesh Wet, Multi-Plate Gear Chain Regina 136 ORP 108 Link Endless 1.75 (105/60) 2.388 (43/18) 2.733 (41/15) 1.947 (37/19) 1.545 (34/22) 1.291 (31/24) 1.154 (30/26) 1.074 (29/27) 6 Speed, Constant Mesh Wet, Multi-Plate Gear Chain Regina 136 ORP 108 Link Endless 1.75 (105/60) 2.388 (43/l 8) 2.733 (41/l 5) 1.947 (37/l 9) 1.545 (34/22) 1.291 (31/24) 1.154 (30/26) 1.074 (29/27) SPEED TRIPLE
Primary Drive Ratio Final Drive Ratio Gear Ratio: 1st 2 n d 3 4 5 6 TYRES Tyre Pressures (Cold) F R Option 1 r e F R Option 2 Front Rear o a r e o n r n a t r t r t t t d h h h
2.5kg/cm2 (36lb/in^2) 2.9kg/cm2 (42lb/in^2) Bridgestone BT56 120/70/17 Bridgestone BT56 190/50/l7 Hi-Sport TX1 5 120/70/l 7 Hi-Sport TX25 190/50/l 7
Michelin Michelin
Bridgestone BT56 190/50/l 7 Michelin Hi-Sport TX15 120/70/17 Michelin Hi-Sport TX25 190/50/l 7
WARNING: Use recommended tyre options ONLY in the combinations given. Do not mix tyres from different manufacturers or mix different specification tyres from the same manufacturers.
Page76
Specifications
BOTH MODELS ELECTRICAL EQUIPMENT Battery . . . . . . . . . . . . . . . . . . . Alternator . . . . . . . . . . . . . . . . Headlight . . . . . . . . . . . . . . . . . Tail/Brake Light
12V 14AH 12V 40A 2xl2V 6O/55W Halogen H4 2xl2V 5/21W 0 12v 1 W
Directional Indicator Lights . FRAME C a s t o r T r a i l Tightening Torques Oil Filter S u m p Spark D r a i n Plug P l u g
Rear Wheel Eccentric Clamp Bolt FLUIDS AND LUBRICANTS Engine Oil: Fully synthetic motorcycle engine oil which meets specification API SH, such as Mobil Brake Coolant Bearings and Pivots M Drive Chain o b i l and Clutch Fluid Mobil Universal Mobil G Mobil r e a s e Chain H P
1 &
Racing Clutch
4T Fluid 2
Brake
or . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MobilubeHD80 NOTE: Mixing different specification oils or mixing oils of the same specification but of a different brand is not recommended except in emergency. If in emergency, oils of different brands or specifications do become mixed, change the engine oil and filter at the earliest opportunity. Engine oils are of a fully synthetic type and must never be mixed with any other types of oil.
Page77
Alphabetical Index
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Disposal . . . . . . . . . . . . . . . . Battery Electrolyte Level Inspection Battery Installation . . . . . . . . . . . . . . Battery Removal . . . . . . . . . . . . . . . . Brakes Brake Fluid Level Inspection and Adjustment . . . . . . . . . . . . . . . . . . . . Brake lever adjuster . . . . . . . . . . . . . Brake Light Switches . . . . . . . . . . . . Brake Pad Wear Compensation Brake Wear Inspection . . . . . . . . . . Disc Brake Fluid . . . . . . . . . . . . . . . . 62 62 63 64 62 Cooling System . . . . . . . . . . . . . . . . . . . Coolant Change . . . . . . . . . . . . . . . . Coolant Level Inspection. . . . . . . . . Corrosion Inhibitors . . . . . . . . . . . . . Radiator and Cooling Fan . . . . . . . . Radiator Hoses . . . . . . . . . . . . . . . . . Drive Chain . . . . . . . . . . . . . . . . . . . . . . . Chain Free-movement Adjustment Chain Free-movement Inspection Chain Lubrication . . . . . . . . . . . . . . . Chain Wear Inspection . . . . . . . . . . 44 44 45 44 44 44 48 48 48 50 49
Dimensions . . . . . . . . . . . . . . . . . . . . . . . 74 52 19 53 52 51 51
Braking . . . . . . . . . . . . . . . . . . . . . . ...... 30 Changing Gears . . . . . . . . . . . . . . . . . . . 29 Cleaning . . . . . . . . . . . . . . . . . . . . . . . .. 71 After Washing . . . . . . . . . . . . . . . . . . 71 Cleaning of the Exhaust System 72 Drying . . . . . . . . . . . . . . . . . . . . . . ...72 Preparation for Washing . . . . . . . . . 71 Protecting . . . . . . . . . . . . . . . . . . . . . 72 Unpainted Aluminium Items . . . . . . 72 W ashing.........................72 Where to be Careful . . . . . . . . . . . . 71 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . ...47 Adjustment . . . . . . . . . . . . . . . . . . . . 47 Inspection . . . . . . . . . . . . . . . . . . . . . 47 Considerations For High Speed Operation . . . . . . . . . . . . . . . . . . . . . . . . 33 Brakes . . . . . . . . . . . . . . . . . . . . . . . . 33 Coolant . . . . . . . . . . . . . . . . . . . . . . . 33 Electrical Equipment . . . . . . . . . . . . 33 Engine Oil . . . . . . . . . . . . . . . . . . . . . 33 Fuel . . . . . . . . . . . . . . . . . . . . . . . . ....33 Miscellaneous. . . . . . . . . . . . . . . . . . 33 Steering.. . . . . . . . . . . . . . . . . . . . . .33 Tyres . . . . . . . . . . . . . . . . . . . . . . . . .33 Coolant Temperature Gauge . . . . . . . 17
Electrical Equipment . . . . . . . . . . . . . . . 77 Engine.. . . . . . . . . . . . . . . . . . . . . . . . .. 74 Engine serial number . . . . . . . . . . . 13 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . Disposal of Used Engine Oil Oil and Oil Filter Change . . . . . . . . . Oil Level Inspection . . . . . . . . . . . . . 41 43 42 41
Fluids And Lubricants . . . . . . . . . . . . . . 77 Frame . . . . . . . . . . . . . . . . . . . . . . . . . ......77 Tightening Torques . . . . . . . . . . . . . 77 Front Suspension . . . . . . . . . . . . . . . . . Compression Damping Adjustment Front Fork Inspection . . . . . . . . . . . Front Suspension Settings . . . . . . . Rebound Damping Adjustment Spring Pre-load Adjustment . . . . . . 54 56 54 55 56 56
Cooling . . . . . . . . . . . . . . . . . . . . . . . . ...75
Page 78
Alphabetical Index
Fuses..............................65 Fuse Identification . . . . . . . . . . . . . . 65 Handbook Storage . . . . . . . . . . . . . . . . 23 Headlights - Daytona . . . . . . . . . . . . . . 66 Headlights - Speed Triple . . . . . . . . . . 68 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Ignition Key . . . . . . . . . . . . . . . . . . . . . . . 18 Ignition Switch/Steering Lock . . . . . . . . 18 Indicator Light. . . . . . . . . . . . . . . . . . . . . 70 Bulb Replacement - All Models . . . 70 Instrument Panel Layout . . . . . . . . . . . . 16 Left Handlebar Switches Direction Indicator Switch . . . . . . . . 21 Headlight Dip Switch . . . . . . . . . . . . 21 Headlight Switch . . . . . . . . . . . . . . . 21 Horn Button . . . . . . . . . . . . . . . . . . . . 21 Passing Button . . . . . . . . . . . . . . . . .21 Left Handlebar Switches . . . . . . . . . . . . 21 Licence Plate, Bulb Replacement - All Models.. . . . . . . . . . . . . . . . . . . . . . . . . . 70 Licence Plate Light . . . . . . . . . . . . . . . . 70 Lubrication . . . . . . . . . . . . . . . . . . . . . ..7 4 Noise Control System . . . . . . . . . . . . . . 3 Parking . . . . . . . . . . . . . . . . . . . . . . . . ..3 2 Performance.. . . . . . . . . . . . . . . . . . . . . 74 Rear Light . . . . . . . . . . . . . . . . . . . . . . . . 70 Bulb Replacement - All Models . . . 70 Rear Suspension Adjustment . . . . . . . 57 Compression Damping Adjustment 57 Rebound Damping Adjustment .. .57 Right Handlebar Switches . . . . . . . . . . 20 Engine Stop Switch . . . . . . . . . . . . . 20 Starter Button . . . . . . . . . . . . . . . . . . 20 Running-in . . . . . . . . . . . . . . . . . . . . . . . 24 Safe Operation . . . . . . . . . . . . . . . . . . . . 25 Daily Safety Checks . . . . . . . . . . . . 25 Scheduled Maintenance . . . . . . . . . . . .38 Seat Lock Operation/Seat Removal .23 Side Panel . . . . . . . . . . . . . . . . . . . . . . . 40 Side Panel Refitting . . . . . . . . . . . . . 40 Side Panel Removal . . . . . . . . . . . .40 Speedometer . . . . . . . . . . . . . . . . . . . . . 16 Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Steering/Wheel Bearings . . . . . . . . . . . Inspection . . . . . . . . . . . . . . . . . . . . . Steering Inspection . . . . . . . . . . . . . Wheel Bearings Inspection . . . . . . . 53 53 53 54
Storage Preparation after Storage . . . . . . . . 73 Preparation for Storage . . . . . . . . . . 73 Table of Contents . . . . . . . . . . . . . . . . . . 2 Tachometer . . . . . . . . . . . . . . . . . . . . . . . 16 Throttle Grip . . . . . . . . . . . . . . . . . . . . . . 46 Adjustment . . . . . . . . . . . . . . . . . . . . 46 Inspection . . . . . . . . . . . . . . . . . . . . . 46 To Start The Engine . . . . . . . . . . . . . . . . 28 To Stop The Engine . . . . . . . . . . . . . . . . 28 Tool Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Transmission . . . . . . . . . . . . . . . . . . . . . 76
Page 79
Alphabetical Index
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . 58,76 Minimum Recommended Tread Depth . . . . . . . . . . . . . . . . . . . . . . . . . 59 Tyre Inflation Pressures . . . . . . . . . 58 Tyre Pressures (Cold) . . . . . . . . . . . 76 Tyre Replacement . . . . . . . . . . . . . . 60 Tyre Wear . . . . . . . . . . . . . . . . . . . . . 59 Vehicle, Vehicle identification number (V.I.N.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warning Lights . . . . . . . . . . . . . . . . . . . . 17 Warnings Warning label location . . . . . . . . . . . 8 Warning Labels . . . . . . . . . . . . . . . . . 1 Warning, Caution and Note . . . . . . 3 Windscreen Cleaning . . . . . . . . . . . . . . 64
Page 80