Escolar Documentos
Profissional Documentos
Cultura Documentos
06/08/12 5:45 PM
06/08/12 5:45 PM
Al/SiC particle composite. 1. The thermal expansion co-efficient can be tailored to adjoining components by adjusting the volume of reinforcement. 2. The composite has high dimensional stability or resistance to deformation under load known as creep. The smaller the reinforcement particles the greater the strength and creep resistance. The composite has been used in missile guidance systems replacing certain berylium components because structural performance is better without special handling in fabrication demanded by the latter's toxicity. [1],[9] I. Silicon-Carbide (SiC) Whiskers Aluminum-matrix composites are reinforced with SiC whiskers, which are more costly than particles due to the following advantages. 1. Single crystal whiskers have high tensile strength than other discontinuous reinforcements such as particles, polycrystalline flakes and chopped fibers. 2. Standard metal working methods can orient whiskers in the metal-matrix. 3. Extrusion,rolling,forging and superplastic forming can impart directional strength. Longitudinal tensile strength increases when the aluminum composite is extruded, since whisker tend to align along the die's axis as the material moves through. Sheet rolling can import directional strength and cross rolling makes properties more uniform.Superplastically formed horseshoes have been used where lightness and wear are a competitive edge. [3],[9] II. Boron-Reinforced Aluminum Composites Boron-reinforced aluminum MMC combines the outstanding strength, stiffness and low density of the boron fiber with fabrication and engineering reliability of an aluminum alloy. The overall improvement in modulus to density ratio of the boron fiber is almost six times that of any of the standard engineering materials, including steel, aluminum, molybdenum, and magnesium. This is advantageous in the prevention of microbuckling of the fibres in the matrix under compression. Other important physical and mechanical properties of Boron/aluminum composites include high electrical and thermal conductivity, ductility, and toughness, nonflammability and the ability to be coated, formed and heat treated ,and joined. [7],[8] III. Graphite-Aluminum Composites The Gr/Al composites are very attractive because the composite can be designed with the coefficient of thermal expansion approaching zero. The extremely high stiffness of the graphite fibers makes possible a composite that is ideal for applications where precise pointing and tracking are required. These are well suited for strut assemblies, especially in space structures that are subject to a wide temperature range across them. Graphite aluminum is also applicable for stable instrument platforms, electronics, and thermal control
http://satyameva-jayate.net/almmc.htm Page 2 of 6
06/08/12 5:45 PM
devices such as heat pipes. Stiffness to weight is high since the material is 30 percent stiffer than aluminum with no thermal expansion. [9] Fabrication of Al based MMCs The fabrication of metal matrix materials may be considered in two stages: the fabrication of the composite material from base metal and fibre reinforcement, and the subsequent fabrication of laminates from the composite material.In some cases, the two steps occur simultaneously depending on the final material product desired and the method of fabrication used in the process. The choice of methods used to fabricate a composite material depends on the mechanical and chemical properties of the fiber and matrix, the fiber length and size, the fiber packing, and the desired fiber configuration. Furthermore, it is necessary to know the thermodynamics and kinematics of possible fiber matrix reactions and service temperatures to which the composites are subjected.A short overview of some of the methods used to fabricate aluminum matrix composites (AMCs) are discussed below. [6] 1. Solid State Processing Incorporation of reinforcing fibres in the metal matrix by solid state bonding is achieved through diffusion bonding at high pressures and elevated temperatures.However, the degree of diffusion must be limited or unwanted brittle phases may be grown at the interfaces. One means of limiting the diffusion time is by extrusion of a sandwich of fibres and matrix through a die. Hot rolling may also be used but, in this case, the deformation of the matrix must be limited to minimize the displacement of the reinforcing fibres to avoid damage. Elevated temperatures are used to facilitate matrix flow but care must be taken to avoid excessive heating that would promote chemical attack of the fibres. A disadvantage of this process is the need for very clean surfaces before bonding is attempted. This usually requires precleaning of the constituent materials and operation in a vacuum. B/Al and Borsic/Al composites are consolidated using this method. [5] 2. Liquid state processing In attempting to bond the metal matrix to the fibres, it is desirable to have the liquid from the matrix flow into the interstices of the fibre tows to provide complete coating of the fibres. Such a process, utilizing a dip bath, can facilitate production considerably and is currently used by the industry to produce wire pre-forms. The disparity between the need to wet the fibres and the avoidance of excessive chemical reaction between the fibre and the matrix necessitates the pre-treatment of fibres by coating them with a compound of titanium diboride. The coated fibres are then drawn through a bath of molten aluminum in a continuous process. Liquid infiltration of molten aluminum into the fibre tow provides a means of separating the fibres as well as providing a bonding interface between matrix and fibre. Fibre coating such as titanium diboride aid wetting as well as protecting the fibre from chemical attack at elevated temperatures. [5] 3. Powder Metallurgy Powder Metallurgy involves the blending of rapidly solidified powders with particulates, platelets or whiskers, through a series of steps. The sequence of steps include: 1. Sieving of rapidly solidified particles 2. Blending of the particles with the reinforcement phase(s)
http://satyameva-jayate.net/almmc.htm Page 3 of 6
06/08/12 5:45 PM
3. Compressing the reinforcement and the matrix mixture to about 75 percent density 4. Degassing and final consolidation by extrusion, forging, rolling or any other hot working method. 4. Physical Vapour Processing (PVD) This type of processing represents a range of methods including electron beam evaporatio}, Magnetron sputtering and electro-deposition methods where composites are fabricated by deposition of successive layers of matrix being deposited on fibre reinforcements. Physical Vapor Deposition (PVD) techniques involve much less heating of the fibres than liquid infiltration. The surface temperatures are typically maintained below 200 C. This technique is widely used to produce Gr/Al composites. [5] 5. Direct Processing/Spray Deposition In this method, finely divided molten droplets allowed to impinge on a substance before they completely solidify allowing direct formation of near net shapes rather than having to go through the intermediate steps of P/M. One such commercial process is the Ospery Process. Though this process does not exhibit solidification rates as high as the rapid solidification ,it offers two advantages: direct production of preform shapes and direct inclusion of reinforcing materials into the parent matrix ("Co-spray deposition"). Billet and disk preforms are being evaluated using materials such as aluminum -matrix composites (AMCs) and superalloys. Direct production/Spray deposition allows effective use of material and elimination of various processing steps. [12] Testing 1. Non-Destructive Evaluation (NDE) An essential aspect of cost effective manufacture is reliable quality control. This is of particular importance with composite materials where consistent quality is essential in maximizing benefits. MMCs are becoming commercially viable engineering materials, but the application of state-of-the-art composites is often limited by the lack of reliable material qualification techniques . Specifically, MMCs provide a significant challenge for conventional non-destructive evaluation methods because of their complex microstructural characteristics. A particularly important aspect of NDE for MMCs involves material fabrication and the option for process interactive control. Because of the large number of processing parameters associated with the fabrication of MMCs, the possibility for detrimental discontinuities is high. In-process NDE can be a useful, cost-effective means of reducing those discontinuities. The NDE technique is studied for the system silicon carbide particulate -reinforced aluminum fabricated by P/M. [10] 2. Ultrasonic Tests Ultrasonic tests of the consolidated MMC billet were performed in an immersion tank equipped with an automated X-Y-Z transducer positioner and a rotating turn-table. A personal computer(PC) based data acquisition system was utilized throughout the experiments. Signal amplitude and time-of-flight data were recorded for both data processing and display. Ultrasonic methods are used to identify SiC clusters in large scale. They can also be used to determine the anisotropic stiffness constants of composite extrusions. 3. Eddy Current Tests
http://satyameva-jayate.net/almmc.htm
Page 4 of 6
06/08/12 5:45 PM
Eddy current tests were conducted on the circumferential surface of the bottom section of the billet. A PCbased data acquisition system was used. The eddy current instrument was used as the frequency generator and impedance detector,and the output was digitized by a converter installed in the the PC system.The eddy current measurements are effective in direct measuring and mapping the near surface consolidation density. The various measurements are graphically represented below. Finally, multiple NDE techniques are required to assess microstructural features important to the quality and long term serviceability of MMCs. With further development, NDE techniques can be incorporated into specific fabrication processes to provide on-line, closed loop control of manufacturing. Conclusions MMCs present some unique challenges for designers and materials engineers in the aerospace industry. From the materials stand point, they require an understanding of the interaction of two chemically different materials under extreme processing and operating conditions. From the design stand point, they require reconsideration in terms of component design, fabrication, lifing and quality assurance in order to obtain the most benefits from these materials. References 1. W.Wei, "High Temperature MMCs for Aero-engines:Challenges and Potentials", Metals and Materials J.,p:430-435, August-1992. 2. T.S.Srivatsan, I.A.Ibrahim, F.A.Mohammed and E.J.Lavernia, "Processing techniques for particulatereinforced metal matrix composites", J. Materials Science, v:26, p:5965-5978, 1991. 3. D.Charles, "Addressing the challenge of aircraft component design and manufacture from MMCs", J. Aerospace Engg.(Proc. IMechE), p:1-13, 1992. 4. Richard T.Holt,"Recent developments in aluminum technology for aerospace applications", Canadian Aeronautics and Space J., v:35, p:128-137, Sept-1989. 5. D.A.McCoy and D.J.Lloyd, Fabrication of graphite fibre reinforced aluminum", Canadian Aeronautics and Space J., v:33, p:11-17, March-1987. 6. A.N.Palazotta, Robert Ruh and George Watt, "Introduction to metal matrix composites in aerospace applications", J. Aerospace Engg., v:1, p:3-17, January-1988. 7. Michael E.Buck, "Advanced fibres for advanced composites", Advanced Materials and Processes", p:61-68, September-1987. 8. Alan.L.Geiger and Michael Jackson, "Low-expansion MMCs boost avionics", Advanced Materials and Processes", p:23-30, July-1989. 9. Richard DeMeis, "New life for aluminum", Aerospace America, p:26-29, March-1989. 10. P.K.Liaw,R.E.Shannon, W.G.Clark, W.C.Harrigan,H.Jeong and D.K.Hsu, "Determining material properties of metal -matrix composites by NDE", JOM, p:36-40, October-1992. 11. J.Wadsworth and F.H.Froes, "Developments in metallic materials for aerospace applications", JOM, p:12-19, May-1989. 12. F.H.Froes, "Aerospace materials for the twenty-first century", Israel Journal of Technology, v:24, p:141, 1988. 13. J.Doychak, "Metal and intermetallic -matrix composites for aerospace propulsion and power systems", JOM, p:46-51, June-1992. 14. F.H.Froes, "Synthesis of metallic materials for demanding aerospace applications using powder metallurgy techniques"
http://satyameva-jayate.net/almmc.htm Page 5 of 6
06/08/12 5:45 PM
15. Alan S. Brown, "Rivals take different paths to JSF", Engineering Notes, Aerospace America, August, 1998.
Back to top
back to Research Papers Tell me what you think of this web page! Thanks!- S.Prasad
http://satyameva-jayate.net/almmc.htm
Page 6 of 6