Escolar Documentos
Profissional Documentos
Cultura Documentos
47LE8500
LED Backlights
Le
an
LCD-DV Troubleshooting 47" Class Full HD 1080P LCD TV (47" diagonally)
dr o
Published July 23, 2010 Updated December 06th, 2010
Pa
lm
ei ra
OUTLINE
Preliminary Section: Contact Information, Preliminary Matters, Specifications, LCD Overview, General Troubleshooting Steps, Signal Distribution, Disassembly Instructions and Voltages Disassembly Section: Removal of Circuit Boards Switch Mode Power Supply Troubleshooting Section: Board Operation Troubleshooting of :
Main Board
Extension Boards
Ft Control Board
Soft Touch Keys
Speakers
2 July 2010 LCD TV 47LE8500
Le
an
dr o
Pa
lm
ei ra
Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These techniques will also be presented. This Section will get the Technician familiar with the Disassembly, Identification and Layout of the LCD Display Panel.
At the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
Le
an
dr o
Pa
lm
This Section will cover Contact Information and remind the Technician of Important Safety Precautions for the Customers Safety as well as the Technician and the Equipment.
ei ra
Section 1
47LE8500
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
47LE8500
ESD Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.
Le
an
dr o
Pa
Regulatory Information
lm
July 2010 LCD TV
ei ra
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti-static bag to a ground connection point or unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
47LE8500
LG Contact Information
Customer Service (and Part Sales) Technical Support (and Part Sales) USA Website (GSFS) Customer Service Website Knowledgebase Website LG Web Training LG CS Learning Academy (800) 243-0000 (800) 847 7597 847-7597
http://gsfs-america.lge.com
ei ra
lm
https://lge.webex.com
Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owners Guides, Interconnect Diagrams, Dimensions, Connector IDs, Product Pictures and Features.
42SL80, 47LG90, 47LH85, 42LE5500, 42LX6500 (3D), 47LX9500 (3D), 55LX6500 (3D) 42PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80, PLASMA: 50PK950, 50PS60, 60PK750, 60PK950, 60PS11, 60PS60, 60PS80 , , , , , , , , , , LCD-DV: LCD DV: 32LD350, 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90,
Also available on the Plasma Page: PDP Panel Alignment Handbook, Plasma Control Board ROM Update (Jig required)
Le
an
dr o
Pa
Published July 2010 by LG Technical Support and Training LG Electronics Alabama Inc. Alabama, Inc 201 James Record Road, Huntsville, AL, 35813.
47LE8500
Le
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage and part number accuracy. 2. Check the model label. Verify model names and board model matches. 3. Check details of defective condition and history. Example: Oscillator failure dead set, etc
an
dr o
Pa
lm
ei ra
47LE8500
Le
an
dr o
Pa
lm
ei ra
47LE8500
This section of the manual will discuss the specifications of the 47LE8500 LCD Direct View Display
9 July 2010 LCD TV 47LE8500
Le
an
dr o
Pa
lm
ei ra
dr o
Wireless Receiver/Transmitter Dongle Attaches via Velcro to the back of the set
Pa Le an
HDMI
lm
ei ra
Media Box
10
47LE8500
dr o
Pa
Wireless Router
Le
an
lm
July 2010 LCD TV
ei ra
11
47LE8500
Basic Specifications
Key TV Features
INFINIA Series* Full LED Slim w/Local Dimming THX Certified Display NetCast Entertainment Access* (Wi-Fi Ready) Wireless 1080p Ready* DLNA Certified TruMotion 240Hz Full HD 1080p Resolution 9M:1 Dynamic Contrast Ratio Seamless Design Picture Wizard II (Easy Picture Calibration) Smart Energy Saving ENERGY STAR Qualified XD Engine Intelligent Sensor AV Mode II (Cinema, Sports, Game) Clear Voice II ISFccc Ready 24P Real Cinema USB 2.0 (JPEG, MP3, DivX HD) DivX HD 4 HDMI V.1.3 w/Deep Color SIMPLINK Connectivity Dolby Digital 5.1 Decoder Infinite Sound
Le
an
dr o
Pa
lm
ei ra
12
47LE8500
Le
an
Entertainment on tap. NetCast Entertainment Access brings the best Internet services direct to your TVno computer required. Instantly access movies and TV shows, news and weather and the worlds largest library of HD movies in 1080p.
dr o
You dont have to take our word for it that this is an amazing TV. To earn THX certification, our TVs passed more than 30 rigorous tests, ensuring youre bringing an uncompromised HD experience home - as the director wanted it.
Pa
lm
ei ra
13
47LE8500
Le
an
dr o
Pa
lm
ei ra
14
47LE8500
Save Energy, Save Money Home electronic products use energy when they're off to power features like clock displays and remote controls. Those that have earned the ENERGY STAR use as much as 60% less energy to perform these functions, while providing the same performance at the same price as less-efficient models. Less energy means you pay less on your energy bill. Draws less than 1 Watt in stand by.
Le
an
Save Energy, Save Money It reduces the plasma displays power consumption. The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home. (Turns on Intelligent Sensor).
dr o
Pa
lm
Clear Voice Clearer dialogue sound Automatically enhances and amplifies the sound of the human voice frequency range to provide high-quality dialogue when background noise swells.
ei ra
15
47LE8500
TruMotion 240Hz See sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LGs TruMotion 240Hz technology. Now your TV can keep up with the fastest moving scenes.
Le
Seamless Design You'll love the stunning picture while it's on and marvel at its appearance while it's off. The display is a seamless, edge-to-edge panel of glass over an ultra-slim, almost unnoticeable bezel. It's a sleek, elegant, virtually border-free design that will appeal to even the most refined sense of style.
an
dr o
Pa
Picture Wizard Get easy self-calibration with on-screen reference points for key picture quality elements such as black level, color, tint, sharpness and backlight levels. Take the guesswork out of picture adjustments with this simple-to-use feature. It's not actually magic, but it will sure seem that way.
lm
ei ra
16
47LE8500
BOTTOM PORTION
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
17
47LE8500
Le
an
dr o
Pa
lm
To access the Service Menu. 1) You must have either Service Remote. p/n 105-201M or p/n MKJ39170828 2) Press In-Start 3) A Password screen appears. 4) Enter the Password.
ei ra
105-201M
MKJ39170828
18
47LE8500
USB1 or USB2 for Software Upgrades, Wireless Dongle, Music and Photos
Side In/Out
ei ra lm Pa dr o
MAIN BOARD Rear and Side Input/Output locations
LAN
USB 2
Le
an
HDMI 4
19
47LE8500
Le
Bring up the Customers Menu then Press the Red button on Remote
an
dr o
Scroll down to item 9 Network Connections
Pa
July 2010 LCD TV
lm
ei ra
20
47LE8500
Pa Le an dr o
If you select Yes; Service call number, Model name, SW version and serial No. is displayed. Note: Confirm the Suffix of the model number. If the Main board is replaced, the Model and Serial number must be reinserted into memory. See Model Number D/L.
lm
ei ra
Check Update version - comparison current software version and Released software version Additional TV Checks can be made by Scrolling down. Picture, Sound and Network Test
After completion of the test, a Pop up menu is displayed with preloaded back ground picture. Select NO if everything is OK.
21
47LE8500
2) Copy new software (xxx.epk) to "LG_DTV" folder. Make sure to have correct software file. 3) With TV turned on, insert USB flash drive. 4) You can see the message TV Software Upgrade (See figure to right) 5) Cursor left and highlight "START" Button and push Enter button using the remote control. 6) You can see the download progress Bar. 7) Do not unplug until unit has automatically restarted. 8) When download is completed, you will see COMPLETE. 9) Your TV will be restarted automatically.
Le
an
dr o
* CAUTION: Do not remove AC power or the USB Flash Drive. Do not turn off Power, during the upgrade process. Software Files are now available from LGTechassist.com
Pa
July 2010 LCD TV
lm
ei ra
22
47LE8500
Pa
Highlight the Software update file and press SELECT to begin the download process.
lm
WARNING: Use extreme Caution when using the Manual Forced Download Menu. Any file can be downloaded when selected and may cause the Main board to become inoperative if the incorrect file was selected.
Le
an
dr o
ei ra
July 2010 LCD TV
23
47LE8500
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
24
47LE8500
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
25
47LE8500
5) Downloading Complete
Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G. This means that when PCM is OK, PCM audio is priority and when AC3 is OK, AC3 audio is priority.
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
26
47LE8500
13.15/16" 353.22mm
11.5/8" 295mm
dr o
19.11/16" 500mm
30.3/16" 767.08mm
Pa
Center
lm
7.7/8" 200mm
2.3/8" (60.32mm) Weight w/o Stand 59.4 lbs Weight with Stand 70 lbs
Le
an
ei ra
8.7/16" 214mm 7.7/8" 200mm Remove 4 screws to remove stand for wall mount
10.13/16" 274.32mm
27
July 2010
47LE8500
LCD-DV
DISASSEMBLY SECTION
Le
an
dr o
Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
Pa
Disassembly: This section of the manual will discuss Disassembly, Layout (Circuit Board Identification) of the 47LE8500 LCD Direct View Television.
lm
ei ra
28
47LE8500
The AC Cord Does Not unplug The Stand has to be removed before removing the back.
Le
an
dr o
Pa
Remove the 26 screws indicated. Pay attention to the size and type of screw as there are many different types. Putting in an improper screw when reassembling may Cause damage.
lm
ei ra
29
47LE8500
Clips hold the front glass in place, use caution. Suggest adding screw while servicing. Extension Board B (Main) Extension Board (Secondary)
Inverter Secondary
Pa
Panel Connection Points
lm
Main Board
Invisible Speaker Left
Inverter Main
LVDS Cables
IR/LED Board
Le
Invisible Speaker Right
an
dr o
LG Logo Board
ei ra
July 2010 LCD TV
30
47LE8500
If the Panel is replaced, reset the UTTTime. Service Menu, System 1 Item 12
CN33 V73~V80
P201
ei ra
CN21 V113~V120
(Secondary)
CN103 CN105 n/c CN31
INVERTER
CN32 V81~V88
CN20
V121~V128 CN4
V1~V8
lm
CN2
INVERTER
(Main)
V29~V136 CN5
V57~V64
POWER SUPPLY
p/n: EAY60908801
Pa
n/c CN11
p/n: AFB72950101
V65~V72
dr o
MAIN BOARD
SK101
an
V73~V80
CN5
CN16 V153~V160
p/n: EBU60842601 for AUSWLH p/n: EBU60842609 for AUSWLUR p/n: EBU60842611 for AUSWNH P8800 P8200
CN27
V33~V40
CN4 V81~V88
CN15 V161~V168
CN26 V41~V48
Le
AC In
CN3 CON2 CON1
V89~V96 CON3
To TFT Panel
CN14 V169~V176
CN25 V49~V56
IR
p/n: EBR64966401
LED
p/n: EAV60793306 AUSWLH p/n: EBR64966901 AUSWLUR / AUSWLNR
July 2010
47LE8500
LCD-DV
31
ei ra lm Le an dr o Pa
AC In SK101
Press in gently on the two tabs to release lock SK101 fits very snug into its connector.
32
47LE8500
Flip the locking tab upward, pull the LVDS ribbon out.
Pa
Remove any tape holding down any cables. Remove the 7 screws indicated by the arrows.
N/C
lm
ei ra
N/C
00 79 P
P7500
P7501
P7901 P8000
dr o
Decorative Metal Plate After removing the Main, there are tabs sticking through the Main board holding the Metal plate in place.
NOTE: Always check on top and behind the Large ICs. And look for a piece of Chocolate (Heat Transfer Material). Be sure to transfer to new Board if present.
Le
an
P8800 P8200
33
47LE8500
p/n AFB72950101 (Comes with Inverter Secondary) Board will run without Inverter (Secondary)
Flip the locking tab upward, pull the ribbons out.
ei ra
Pa
lm
CN1
CN3
CN2
CN4
CN11
CN5
dr o
Le
an
N/C
On CN2, CN3, CN4 and CN5 Flip the locking tab upward, pull the ribbons out.
34
47LE8500
p/n AFB72950101 (Comes with Inverter Main) Board will run without Inverter (Main)
Pa
CN101
lm
ei ra
CN103 N/C
CN104
CN105
Le
an
dr o
On CN104 and CN105 Flip the locking tab upward, pull the ribbons out.
35
47LE8500
p/n EBR64966401
Tab
N CO
CON3
Pa
Le
an
dr o
lm
July 2010 LCD TV
ei ra
Tab
36
47LE8500
TROUBLESHOOTING SECTION
Le
an
dr o
Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.
Pa
lm
ei ra
37
47LE8500
P204 Connector: (To Inverter Main Board) 24V is routed out P204 pins 1 through 5. P205 Connector: (To Inverter Secondary Board) 24V is routed out P205 pins 1 through 5.
Le
an
P201 Connector: (To Main Board) 12V is routed out P201 pins 17, 19 and 21 and 24V is routed out P201 pins 2, 3 and 4.
dr o
When the controller chip receives the PWR-ON command 3.3V via P201 Pin 1, the primary section increases its current supplying ability. Both Primary fuses F101 and F501 now read a little more than 390V.
Pa
July 2010 LCD TV
lm
ei ra
38
47LE8500
p/n EAY60908801
ei ra dr o Pa lm
F101 3.15A/250V STBY 2.9V Run 393.3V From Hot Gnd F501 3.15A/250V STBY 159.6V Run 392.6V From Hot Gnd
Le
an
39
47LE8500
1
Bridge
Primary side fuse: POWER Stand-By 159.6V Run 392.6V (Hot Gnd)
SUPPLY (SMPS)
24V B+ for the Inverters
6 9
P205
6 8
24V P DIM
ei ra
9 8
12V/24V Regulators
P204 24V CN1 CN2 6 Inverter Main P DIM INV On CN11 CN3
RL_ON
2
P8000
3.5V_ST 2
6
24V Audio
Pa
lm
CN14~CN22
PWM-DIM Digital Dimming 8 IC9301 Dimming IC IC9103 DC to DC 7 VCC 3.3V, VDD 16V, VGL -5V, VGH 26V, After Mute Released LVDS Video P7500 10 P7501 Tru-Motion LVDS Video P8200 P7901 10 P7900 MOSI, CLK
dr o
IC9302
1.8V Dimming
an
MAIN BOARD
Power On 5
Inverter On
P-DIM
RL_On
12V
Le
Other Regs
7 9 7 4
Power RL_ON On
INV_CTL
LCD Panel
Ft IRKey
July 2010
47LE8500
LCD-DV
R8003 22K R8010 10K 11.8V 1.8V 11.8V 3.36V R8060 10K
Panel_Vcc (12V)
11.79V L8015
Q8004
+12V L8000
S G
Q8003
0.68V
Q8001
0V
R8001
47K
R8103
100
SMPS P201
PWR 24V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3.3V 24.6V 24.6V 24.6V Gnd Gnd Gnd Gnd 3.44V 3.44V 3.44V 3.44V Gnd Gnd Gnd n/c 11.9V 2.92V 11.9V 0.37V~3.3V 11.9V n/c n/c Gnd
7
3.36V
IC8005
2 6
+12V 20 R8176
22K Power On/Off 2_2
PWR-ON +24V
L8005
Power_On/Off2_2
ei ra
IC8101 Micro
IR
16
3.3V
Q8002
Q8000
0V
0V
0.66V
lm
R8004
4.7K
R8000
10K
RL_ON
36 RL_ON R8187
22
Pa
SBY3.5V
L8003
3.36V
Model_Opt_1 11
R8135 40
Reset Power Det 14 Key 1 25 Key 2 26 22
+3.5V_ST
+3.5V_ST
dr o
C8001 100uF
C8000 100uF
R8026
1K 3.1V
n/c 12V INV_CTL 12V PWM-DIM 12V n/c n/c ERR OUT
15 16 17 18 19 20 21 22 23 24
n/c INV_On
+12V
11.9V
L8002
+3.3V_Normal
an
Q8005
0V
R8019
100
10 R8032
10K
INV_CTL
R8134
22
Le
IC900 BCM
R25 GPIO 09 R1041
0
R8027
0
PWM-DIM (PWM Dimming) can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.
41
July 2010
47LE8500
LCD-DV
Pa
lm
If 3.5V Standby is not being generated, the SMPS is defective and must be replaced. There is no need to continue with the next test. But, make sure AC is arriving at the connector SK101.
ei ra
(b) Unplug P8000 on the Main Board to make insertion of the Jumpers easier. Use P700 Side to insert resistors TEST 1:
(1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC. This will turn on the power supply, relays will click. a) Check that the 24V and 12V power supplies are turned on, P201 (12V pins 17, 19 and 21) P201 (24V pins 2, 3 and 4) P204 and P205 (24V pins 1 through 5) to the Inverters (2) Remove AC power
Le
an
dr o
42
47LE8500
Pa
lm
ei ra
If the 24V and the Inverter On command is arriving at the Inverters in, then see Inverter Section for further testing. Note: Either Inverter can run separately. REMOVE AC POWER:
Le
an
Backlights Abnormal: a) Recheck all connections. b) Confirm the INV On/Off line pulling up to at least 3V and arriving at both Inverters. c) Check the connections to the Inverters.
dr o
43
47LE8500
P201 Connector
Label PWR-ON 24V GND 3.5V Gnd n/c 12V INV-ON 12V P-DIM 12V n/c n/c ERROR
Run 3.3V 24.6V GND 3.44V Gnd n/c 11.9V 2.92V 11.9V 0.37V~3.3V 11.9V 0V 0V 0V
Diode Check 1.68V GND Open Gnd Open 1.39V Open 1.39V Open Open Open Open 1.39V 0.424V
lm
ei ra
1
Odd pins are on front row
Le
an
dr o
Pa
(1) PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V. .
44
47LE8500
P205
lm
ei ra
Pin 1-5 11 12
Label 24V
STBY 0V GND 0V 0V
Pa
6-10
GND
(1)
P-DIM I-C
dr o an
(2)
(1) PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V.
(2)
Le
45
47LE8500
SK101 "SMPS" to AC IN Pin EL131 EL132 Label L N STBY Run Diode Check
120Vac
dr o
N
Pa
F100 (Diode Check) Main Power Switch Closed Red or Black Lead on Fuse (Open) Other Lead on Hot Ground
F100
Le
an
lm
SK101 46
AC Voltage Readings (From Hot Ground) Pins 1 and 2 for STBY and RUN.
ei ra
OL
OL
47LE8500
ei ra lm
If reading the voltage on F101 right after power off, it takes a very long time to bleed down to the reading given here.
F501 F501 3.15A/250V From Hot Gnd STBY 159.6V Run 392.6V
Le
an
dr o
F101
F101 3.15A/250V
Pa
47
47LE8500
Inverter (Secondary) has 2 Connectors CN104~CN105 that connect to the right hand Extension board (as viewed from the rear) which connects to CN23 and CN24. Each Extension board has 9 connections to the Backlight LEDs. There are 4 LEDs per/block, 216 Blocks, 8 Blocks per/cartridge, 3 Cartridges per/bar, 9 bars (rows), 32 LEDs per/cartridge, 96 LEDs per/bar. With a total of 864 LEDs.
Le
Inverter (Main) has 4 Connectors CN2~CN5 that connect to Extensions boards. The Left hand Extension board (as viewed from the rear) connects to CN2 and CN3 and the Center Extension board connects to CN4 and CN5.
an
dr o
The Inverters must also deliver grounding pulses (Drive Signals) to each of the 216 LED Blocks. This is accomplished by the 15 switching components, 10 on Inverter (Main) U3~U11 and U13 and 5 on Inverter (Secondary) U2~U5 and U13.
Pa
Inverter (Secondary) 13V U101, Q105, Q106, L206 and C151, out CN104 and CN105.
lm
ei ra
48
47LE8500
IOP Structure
The Image below shows the actual Backlight Bars used in the 47LE8500. The Cartridges are assembled from the bottom to the top, like shingles on a roof.
Cartridge Bar
Le
an
dr o
Cartridges Removed
Pa
July 2010 LCD TV
lm
ei ra
49
47LE8500
Cartridge
Le
an
dr o
Pa
lm
ei ra
Bar
50
47LE8500
LED
an Le
51
dr o
White Sheet Light Uniformity
Pa
Lens (Reflector)
lm
ei ra
July 2010
50PK750
Plasma
CN23
CN32 V81~V88
ei ra
CN9 V41~V48
CN20
CN31 V1~V8
V121~V128
lm
CN8
CN12
CN30 V9~V16 CN24 V17~V24 CN29 CN28 V25~V32 LED Extension Board
Pa dr o
CN6 V65~V72
V145~V152
CN5 V73~V80
CN16 V153~V160
CN27 V33~V40
an
CN4 V81~V88
CN15 V161~V168
CN26 V41~V48
Le
CN3 V89~V96
CN14 V169~V176
CN25 V49~V56
Backlight Blocks 9 Bars (24 Blocks Ea.) 216 Blocks V1 through V216
3 Extension Boards 9 Connectors Ea. 2 (13V) B+ pins Ea. 8 (V) Connections Ea. 216 (V) Connections
52
July 2010
47LE8500
LCD-DV
Le
an
dr o
Pa
lm
ei ra
13
1. Case-Top Assy 2. TFT Panel Assy 3. Guide Panel 4. Sheet DBEFD 5. Sheet Prism U 6. Sheet Prism L 7. Sheet Diffuser L 8. Plate Diffuser 9. Cartridge Assy 10. Cover Bottom 11. Driver Boards (2) 12. Extension Boards (3) 13. FRC
Flexible Ribbon Cables
53
47LE8500
CN3
CN2
Q16
C
24.6V F1 12A/65V U6 U5 U8
E B B E
Q4
24.6V
CN4
Q2
ei ra
13V
U13
B E
INVERTER (MAIN) BOTH INVERTERS p/n: AFB72950101 13V POWER SUPPLY For CN2 / CN3 Q11
C B E
lm
U101 Q10
C B E
U7
Gnd
Pa
13V 13V POWER SUPPLY For CN4 / CN5 L102 12.77V 13V
U4
U3 Q15
U11
B E
Q7
dr o
3.3V
U103
E B
L103
U501
U1
U10
CN5
8Mhz Y501 8Mhz Y1 U9
Q3 C U102 Q8 C89
A0948 1050 C -
an
Q12
3.46V
13V
Le
+
DO NOT MEASURE
CN11
54
July 2010
47LE8500
LCD-DV
U103 Q12
C B E
Q3
24.6V
A0950 1050 C
U101
Q106
lm Pa
C151
A0948 1050 C
E B
Q103
E B
dr o
13V
ei ra
U5 Y501 8Mhz U4
Q102
12.8V
Q501
B E C
CN105 U501
Le
13V
an
L206 N/C CN103 U3
Q105
55
July 2010
47LE8500
LCD-DV
CN1
A0950 1050 C
CN3
CN2
ei ra
Q1
C
Q16
C E
+ 24.6V 12.96V
A
U8
E B B
Q4
C98
B CN4
Q2
B
C E
A
Q5
A
INVERTERS (MAIN)
U13
lm
To CN 12 Extension Cent CN4 B+ for LED Blocks. Pins 11~12, 21~22, 31~32, 41~42
Gnd Q10
C B E
C75
+ 13V Q11
C B E
U4
Pa
U7
U3 Q15
U11
B E C
Q7 DC to DC Driver
dr o
U102
L102 Q8 C89
A0948 1050 C
Q3 3.46V Q12
an
L103
U10
B CN5
U501 U1
13V +
Le
CN11
U9
To CN 13 Extension Cent CN5 B+ for LED Blocks. Pins 9~10, 19~20, 29~30, 39~40, 49~50.
Q5 5V 1 2 12.9V 3 Gnd
Q8 5V 1 2 12.8V Gnd 3
A 12.92V For Main Extensions Board A (Left Side). To Connectors CN2 and CN3. B 12.92V For Main Extensions Board B (Center). To Connectors CN4 and CN5.
56
July 2010
47LE8500
LCD-DV
Q3
24.6V
A0950 1050 C
Q106 Gnd
C101
CN101
Q101
C E B C
E B
C151
Q103
C
13V
Pa
lm
U5
U501
ei ra
DC to DC Driver U101
INVERTER (SECONDARY)
C CN104
A0948 1050 C
Q102
E B
12.8V
Q501
B E
U4
C CN105
L206
13V
an
dr o
Q105
N/C
Le
C 13V For Secondary Extensions Board (Right Side) Connectors. To Connectors CN23 and CN24.
U3
CN103
57
July 2010
47LE8500
LCD-DV
dr o
Pa
lm
ei ra
30V p/p 296KHz
an
Each of the Pin numbers for the Components listed above are the same.
Le
2
Q5, Q8 or Q106 Pin 3 is Ground
1 58
P-DIM (Global Dimming) Explained: P-DIM (May also be called PWM-DIM, VBR-B, PDS, BCM-VBR-B)
The Video Processor has the output that controls P-DIM. If the Microprocessor is separate from the video processor, then the customers menu Backlights setting is communicated to the video processor via I2C. Maximum P-DIM Voltage 100% 100% Cust Backlight Setting Backlights Bright 3.3V P-DIM Voltage Establishes the maximum threshold or brightness level of the backlights
Brightness of Backlights
dr o Le
Minimum P-DIM Voltage 0% Cust Backlight Setting 0%
an
Pa
lm
ei ra
Backlights Dim
After the max. threshold is established by the Customers Menu, the DC Level of P-DIM is manipulated by: Overall Contrast Ratio Monitored by the BCM or Mstar Video Processor. As the overall brightness of the video content decreases, so does P-DIM voltage.
If the Intelligent Sensor is utilized, it too manipulates P-DIM. As the overall room light decreases in intensity, P-DIM decreases. This data represents nearly 5000 steps in room light monitoring. It is routed from the Front IR board through I2C data back to the Main boards Microprocessor. 0.37V
Brightness and Contrast adjustments do not affect P-DIM Analog Dimming is not used. It is a fixed voltage. Also called BR1, VBR-A, BCM-VBR-A, ADM
59
July 2010
47LE8500
LCD-DV
ei ra lm an dr o
Top Left of the Board Just to the right of CN101 Connector Inverter (Secondary)
F1 (Diode Mode Check) 1.365V (Red Lead on Fuse) 0.58V (Black Lead on Fuse)
Pa
F1 12A/65V
Le
F101 (Diode Mode Check) 1.385V (Red Lead on Fuse) 0.58V (Black Lead on Fuse)
Y1
lm
Inverter (Secondary)
ei ra Le an dr o
Y501 Use Bottom Leg 61 July 2010 LCD TV 47LE8500
Pa
8Mhz
dr o
Pa
lm
ei ra
an
Voltage Supplies from Inverter (Secondary) To Extension Board Right CN104 13V Line Pins 19~20, 29~30, 39~40, 49~50 CN105 13V Line Pins 1~2, 11~12, 21~22,31~32, 41~42
Voltage Supplies from Inverter (Main) To Extension Boards Left and Center CN3 13V Line Pins CN4 13V Line Pins CN5 13V Line Pins 1~2, 11~12, 21~22, 11~12, 21~22, 31~32, 9~10, 19~20, 29~30, 31~32, 41~42 41~42 39~40, 49~50
Le
62
47LE8500
100 IRE 5 IRE 3.68V p/p 120Hz 3.88V p/p 120Hz Note: If a particular block is exhibiting a dimmer level than the other or the overall brightness seems dim, be sure to first check the customers Menu setting for Backlights. Raise the percentage and see if the overall brightness returns to normal. If not, 1st Check the P-DIM level, it should rise with the percentage shown on screen. 0% = 0.37V to 100% = 3.3V. Follow the P-DIM signal all the way to each Inverter. 2nd Turn off the set and unplug the connector to the Inverters coming from the Main board. If the brightness returns to normal, the Main board is defective. If not, investigate all inverter voltages, if OK, use the grounding of each V block procedure to test the panels backlight LEDs.
Le
an
dr o
Pa
July 2010 LCD TV
lm
ei ra
63
47LE8500
ei ra
Le
Inverter Run voltages taken with built in test pattern full white and black screens
40 39 38 37 36 35 34 33 32 31
an
dr o
41
This chart does not show all 50 pins. For all connectors from the Inverters to the Panel, please use the Interconnect Diagram for details on all pins.
Pa
lm
64
47LE8500
Inverter (Main and Secondary) CN1 and CN101(Voltage and Diode Check)
CN1 "Inverter Main" Connector To P204 "SMPS" Pin Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V.
(1) PDIM
Run 24.6V
Diode Check 0.42V GND Open Open Open Open Inverter On Control Not Used
1~5 6~10 11 12 13 14
0.37V~3.3V
ERROR
Pa
STBY 0V GND 0V 0V
dr o
CN101 "Inverter Secondary" Connector To P205 "SMPS" Pin 1~5 6~10 11 12 Label 24V Run 24.6V GND 0.37V~3.3V 2.92V Diode Check 0.42V GND Open Open Inverter On Control
Le
an
GND I-C
(1)
P-DIM
lm
0V
ei ra
GND 2.92V N/C
65
47LE8500
Inverter (Main) CN11 & Inverter (Secondary) CN103 (Voltage and Diode Check)
Inverter Run voltages taken with built in test pattern CN11 Inverter Main to Main P7900
Pin 1 2 3 4 5 6 7 8 9 10 Label L_VS M0_MOSI M0_SCLK GND M1_MOSI M1_SCLK GND S_CS_N S_MOSI S_SCLK STBY 0V 0V 0V GND 0V 0V GND 0V 0V 0V Run 0.05V *0.04V~3.26V 0.23V GND *0.04V~3.26V 0.23V GND 2.6V *0.18V~0.28V 2.99V Diode Check Open Open Open GND Open Open GND
lm
Pa
dr o
1.65V 1.61V 1.62V
ei ra
M2_MOSI Gnd n/c n/c Gnd M2_SCLK
*Black to White
Le
*Black to White
an
66
47LE8500
dr o Le an
Pa
For clearer details see the Interconnect Diagram
lm
July 2010 LCD TV
ei ra
67
47LE8500
The Main board also develops several B+ sources on the board. GENERAL 5V_Normal 5V_EXT LVDS 5V USB Panel_VCC (12V Not generated, but switched AUDIO from the 12V arriving from the SMPS. 1.8V TUNER and VSB CIRCUIT 3.3V 5V_Normal which is used to make 5V TU BCM IC900 Video Processors 5V_TU 1.2V 3.3V_TU IC9301 Tru-Motion and Dimming IC. 1.26V_TU 1.26V_MEMC, 1.5V_MEMC, WIRELESS VOLTAGES , D1.5V, D1.8V, and 3.3V 24V (Switched from 24V from SMPS) T-CON IC9001 3.3V_VCC, -5V_VGL, 25V_VGH, 16V_VDD and HVDD (7.7V) STAND-BY VOLTAGES 3.3V_ST (Voltage direct from SMPS)
Le
an
dr o
Pa
lm
ei ra
RUN
68
47LE8500
P7501
P7500
an
dr o
P8100 n/c
Pa
lm
P9000 n/c
VIDEO PROCESSOR IC900, T-CON IC9001 and Tru-Motion IC9301 runs Hot. This is normal.
ei ra Le
P8200 To Front IR
LAN
69
47LE8500
Q
E
D
P7900 SW9300 Tru-Motion and Dimming IC Reset
P7501
A1 A2
IC8005
L9102 D9101 C
A AC A
IC9300 SW9300 X9300 25Mhz X9000 12Mhz IC9001 T-CON LG7378A IC8900
IC9302
L8015
L8904
IC603 P9000 Update SW8100 Microprocessor Reset SW1000 Videoprocessor Reset X8100 SW8100 IC1000 IC8101 SW1000
IC605
ei ra
L8012 IC8002 P9000 Gamma L8009 IC8000
IC700
IC8902
lm
Pa
IC901 L8004
USB1
dr o
an
HDMI Select
IC300 Q300
L8804 L8805 Q?
IC8300
TU700 TDVJ-H031F
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. 7. 6. 5. 4. 3. NC SDA SCL NC NC 5V
Digital Video
Le
Q8201
Q8700
Analog Video
HDMI
Q8200
P8800
P8200
2. NC 1. NC
Q8306 Q8307
70
July 2010
47LE8500
LCD-DV
IC300 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC301 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC302 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q300
Earphone Amp 0V 0V 0V 0V 0V 3.3V 3.3V (-1.8V) (-0.8V) Gnd 0.9V 1.8V 3.3V 3.3V Gnd 0V Switched 5V for USB 2 Gnd 5V (In) 5V 3.3V 3.3V 5V (Out) 5V (Out) n/c Switched 5V for USB 1 Gnd 5V (In) 5V 3.3V 3.3V 5V (Out) 5V (Out) n/c
IC700
(+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.26V (Out) [3] 3.3V (In) SOC Reset Pin Generator [1] 3.32V (In) [2] 0V (Gnd) [3] 3.3V (Out) 5V Regulator for USB 11.79V (In) 5V (Out) 5V (Out) 10.5V 3.3V 0.8V 4.99V 0V (Gnd) D1.2V and A1.2V Regulator 0V (Gnd) 3.3V 0V (Gnd) 1.2V 3.3V n/c 4.46V 3.3V 3.3V 3.3V 1.2V Gnd 3.3V 0.8V
IC8002 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC8003 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8004 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q8005
(D1.8V) Regulator 5V 3.34V (In) 1.8V (Out) Gnd Gnd 0.9V 0.9V 1V 2.38V 3.36V (PWR On/Off1 Ctl) (+5V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.37V (PWR On/Off2 Ctl) 5V (In) 5V (In) A2.5V Regulator for USB n/c 3.26V (In) 3.26V (In) n/c n/c 2.55V (Out) 0.8V 0V (Gnd)
IC8005 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8007
IC1000
IC8000 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8001 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
Power Det Gen Pin (+12V and +3.5V) [1] 0V (Gnd) [2] 3.6V (In) [3] 3.5V (Out) Power Det Gen Pin (+24V) [1] 0V (Gnd) [2] 3.6V (In) [3] 3.7V (Out)
ei ra
(+3.3V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.36V (PWR On/Off2 Ctl) 3.36V (Out) 3.36V (Out)
IC8902 Pin [1] [2] [3] [4] [5] [6] [7] [8]
(+1.26V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.7V 3.36V (PWR On/Off2 Ctl) 1.3V (Out) 1.3V (Out) (+3.3V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.8V 3.36V (PWR On/Off2 Ctl) 3.3V (Out) 3.3V (Out) P-GAMMA Chip 3.3V 0V (Gnd) 3.3V (In) 0V (Gnd) 6.8V 6.8V 15.3V 15.3V n/c 13.47V 12.75V 11.8V 10V 5.96V 4.06V 15.3V 0V 2.96V 2.33V 3.3V (In)
IC9102 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC9300
IC8903
IC8008
lm
DC to DC HVDD T-CON 0V (Gnd) 11.72V (In) 11.72V (In) 3.25V 3.2V 0V 0V 11.7V 0V (Gnd) 1.13V 0V (Gnd) 0V (Gnd) 0V (Gnd) 7.7V 7.7V (HVDD) 0V (Gnd)
Pa
IC9100 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]
IC8800
Reset for Pin LG5111 [1] 3.32V (In) [2] 0V (Gnd) [3] 3.34V (Out) (1.8V_L/Dimming) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.76V 3.34V (PWR On/Off2 Ctl) 1.8V (In) 1.8V (In)
IC9302 Pin [1] [2] [3] [4] [5] [6] [7] [8] D9101
dr o
IC8901
(+1.5V_MEMC) Pin Regulator [1] 0V (Gnd) [2] 1.5V (Out) [3] 3.3V (In) HDMI Det
an
Le
VGH/VDD Pin Rectifyer A 15.4V AC 22.2V C 27.4V (VGH) VGL/VCC Pin Rectifyer A (-5V VGL) AC (-1.9V) C 0V
Q8200
IR Buffer 2nd
HDMI Det
D9102
Q8001
0V 0.68V Gnd
IR Buffer 1st
Q8700 Wireless PWR Dongle Out Turns on Q8701 B 0.66V (0.0V Dongle In) C 0.14V (24V Dongle In) E Gnd
Q8800
71
July 2010
47LE8500 LCD-DV
Q
E
D
Rubber Q8002
A1 A2
3 1 2
Rubber
IC9101
Q8000 IC9303
ei ra
IC602 IC606
IC9000
lm
IC604 Q200
D S G
Q901
Pa
Rubber IC8200 Q8303 D8309 Q8305 D8306 D8307 Q8300 Q8304 IC8400 Q8301 IC8401 Q8203
8. 7. 6. 5. 4. 3.
Le
Q702
Q701
2. NC 1. NC
72
July 2010
Rubber
TU700 TDVJ-H031F
an
dr o
47LE8500
LCD-DV
IC602 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8100 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8200 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16]
ei ra
D1.8V Regulator 0V (Gnd) 3.29V (PWR On/Off1 Ctl) 0.9V (DDR_VTT) 0.93V 1.83V 3.38V (In) 1.8V (Out) 0.91V (DDR_VTT) EEPROM Micro 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 0V (Gnd) 3.37V RS232 Routing 0V 0V 0V 0V 0V (-5.47V) n/c (5.59V) n/c (0V) n/c (3.3V) n/c (0.2V) n/c (3.3V) 3.35V 0V (-5.47V) 0V (Gnd) 3.37V
IC8400 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] IC8401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC9000 Pin [1] [2] [3] [4] [5] [6] [7] [8]
RGB H/V Sync 1.9V 1.9V 4.4V 0V 0.9V n/c (4.5V) 0V (Gnd) n/c (4.5V) n/c (1.9V) n/c (1.9V) n/c (4.5V) 0.9V 0.9V 5V EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 0.7V 4.1V 4.5V 4.5V (In) Serial Flash T-CON 0.06V 0.67V 3.3V (In) 0V (Gnd) 0V 0.34V 3.31V (In) 3.34V (In)
IC8700 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16]
Pa
Wireless Buffer 0V (3.3V Dongle In) 3.3V (0.3V Dongle In) n/c n/c n/c Gnd Gnd Gnd n/c 0.02V 0V 3.3V 0V (3.3V Dongle In) 3.3V 3.3V 3.3V EEPROM for LG5111 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 3.34V 3.37V (In)
Q200
(1.8V_HDMI) Pin Switch S 1.83V (Out) G 3.35V (PWR On/Off2 Ctl) D 1.83V (In) Tuner SIF Pin (Sound) Buffer B 0.16V C Gnd E 0.83V
Q8203
Q701
Q8205
lm
Q702
Tuner Video Pin (Analog) Buffer B 2.05V C 2.75V E Gnd FLASH_WP Pin for IC901 B 0V (Flash_WP) C 3.36V E Gnd RL_ON (PWR_On) Pin 1st Driver B 0.66V C 0V E Gnd PWR_ON Pin Switch [1] 3.36V (In) [2] 0V [3] 3.3V (Out)
Q8300, 2 HDMI 2 Pin Det B 4.2V C 0V E Gnd Q8303, 4, 5 HDMI 3 Pin Det B 0V C 4.2V E Gnd Q8308 Pin [B] [G] [S] [D] Q8701 CEC Remote HDMI CEC 2.72V 2.73V 3.27V 3.37V
Q901
IC9303
an
dr o
Q8000
Q8002
Le
D8306, 7, 9 5V Pull Up Routing Pin HDMI SCL/SDA A1 5.04V C 4.58V A2 0V 3.5V Pull Up Pin HDMI CEC A1 0V C 3.26V A2 3.2V
IR Wireless Pass Pin 2nd Driver G 24.5V (2.3V Dongle I S 24V D 0V (24.5V Dongle In)
D8312
73
July 2010
47LE8500 LCD-DV
X9000 1.56V
2.54V p/p
1.6V
25Mhz
lm
4.86V p/p
ei ra
Pa
3.27V p/p
12Mhz
1.6V
Le
X9000
an
X9001
dr o
MAIN Board
74
47LE8500
Either leg
lm
ei ra
789mV p/p
54Mhz
Runs when set is On
1.3V
an
dr o
Pa
Le
1.85V p/p
2.82V p/p
MAIN Board
1.5V
1.75V
75
47LE8500
+7.81V HVDD
L9100
ei ra
Pa
+16V VDD
lm
dr o
L9102
Le
an
Panel 12V
IC9103
L9101
+3.3V VCC
76
47LE8500
lm dr o Pa an
-4.7V (VST)
ei ra
IC9101 Back Side of Board From IC9101 Pin 21 -4.8V (VDD-ODD)
Le
77
47LE8500
Main Board Connector P8000 to Power Supply Voltage and Diode Check
P8000
P8000 Main Board" to P201 SMPS" Pin 1 2-4 5-8 9-12 13-15 16 17 18 19 20 21 22 23 24 Label PWR-ON 24V Gnd 3.5V Gnd n/c 12V 12V 12V n/c n/c ERROR STBY 0V Run 3.3V 24.6V Gnd 3.44V Gnd n/c 11.9V 2.92V 11.9V 0.37V~3.3V 11.9V n/c n/c 0V Diode Check Open Open Gnd 1.24V Gnd Open Open 1.63V Open Open Open Open Open Gnd
Pa
INV-ON
(1)
lm
dr o an Le
(1)
P-DIM
PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.
ei ra
Gnd Gnd n/c 0V 0V 0V 0V 0V n/c n/c 0V 3.45V
0V
78
47LE8500
Main Board Connector P7500 to the Panel Voltage and Diode Check
P7500 Connector Main" to the Panel
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label Gnd GMA1 GMA3 GMA4 GMA6 GMA7 GMA9 GMA10 GMA12 GMA13 GMA15 GMA16 GMA18 Gnd OPT_N H_CONV VST_IN POL SOE Gnd Run Gnd 14.91V 13.5V 12.78V 11.88V 10.02V 8.02V 7.48V 5.99V 4.08V 2.98V 2.35V 1.06V Gnd 1.06V 1.07V 0V 0.62V 0.3V Gnd Diode Check Gnd Open Open Open Open Open Open Open Open Open Open Open Open Gnd 2.06V Gnd Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label LV0+ LV0LV1+ LV1LV2+ LV2LVCLK+ LVCLKLV3+ LV3-
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
Run 1.06V 1.27V 1.4V 1.3V Diode Check 0.9V 1.09V 0.9V Pin 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Label VDD VDD Gnd VCOM_IN VCOM_FB Gnd VST VGL VDD_EVEN VDD_ODD VGI_P (VGL) VGI_N (VGH) CLK6 CLK5 CLK4 CLK3 CLK2 CLK1 Z_OUT Gnd Run 15.57V 15.57V Gnd 6.86V 6.87V Gnd (-4.7V) (-5V) (-4.8V) (-4.8V) (-5V) 27.4V 8V 8V 8V 8V 8V 8V 7.7V Gnd Diode Check Open Open Gnd Open Open Gnd 1.5V 0.6V 1.5V 1.5V 0.6V Open 1.5V 1.5V 1.5V 1.5V 1.5V 1.5V Open Gnd
1.03V 1.3V
lm
1.16V 1.17V 1.07V 1.27V 1.02V 1.3V 1.02V 1.3V Gnd 3.3V 3.3V Gnd 7.81V 7.81V
Pa
dr o
LV4+ LV4LV5+ LV5Gnd VCC VCC Gnd HVDD HVDD
an
Le
ei ra
1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V Gnd 1.64V 1.64V Gnd Open Open
79
47LE8500
Main Board Connector P7501 to the Panel Voltage and Diode Check
P7501 Connector Main" to the Panel
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label Gnd Z_OUT CLK1 CLK2 CLK3 CLK4 CLK5 CLK6 VGH VGH VGH_ODD VGH_EVEN VGL VST Gnd VCOM_FB VCOM_IN Gnd VDD VDD Run Gnd 7.7V 8V 8V 8V 8V 8V 8V 27.4V (-5V) (-4.8V) (-4.8V) (-5V) (-4.7V) Gnd 6.87V 6.86V Gnd 15.57V 15.57V Diode Check Gnd Open 1.5V 1.5V 1.5V 1.5V 1.5V 1.5V Open 0.6V 1.5V 1.5V 0.6V 1.5V Gnd Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label HVDD HVDD Gnd VCC VCC Gnd RV0+ RV0-
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
Run 7.81V 7.81V Gnd 3.3V 3.3V Gnd Diode Check Open Open Gnd Pin 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Label Gnd SOE POL VST_IN H_CONV OPT_N Gnd GMA18 GMA16 GMA15 GMA13 GMA12 GMA10 GMA9 GMA7 GMA6 GMA4 GMA3 GMA1 Gnd Run Gnd 0.3V 0.62V 0V 1.07V 1.06V Gnd 1.06V 2.35V 2.98V 4.08V 5.99V 7.48V 8.02V 10.02V 11.88V 12.79V 13.5V 14.91V Gnd Diode Check Gnd 1.06V 1.06V 1.06V Gnd 2.06V Gnd Open Open Open Open Open Open Open Open Open Open Open Open Gnd
Pa
1.12V 1.13V 1.23V 1.13V 1.22V 1.17V 1.18V 1.08V 1.27V 1.12V 1.22V 1.13V 1.22V
RV1+ RV1-
dr o
RV2+ RV2RVCLK+ RVCLKRV3+ RV3RV4+ RV4RV5+ RV5-
an
Le
Open Open
lm
1.07V
ei ra
1.64V 1.64V Gnd 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V
80
47LE8500
Main Board P8200 to (Ft. IR/Intelligent Sensor) Voltage and Diode Check
P8200 Connector "MAIN Board" To P100 "IR Board" Pin 1 2 3 4 5 6 7 8 9 10 11 12
(1) Clock (2) IR
P8200
Label
(1) (1)
STBY 3.45V 3.45V Gnd 3.29V 3.29V 3.45V Gnd 0V 1.57V Gnd 0V 0V
SCL SDA
IR
dr o
1.54V Gnd 0V 3.3V
+3.3V_Normal LED_R/BUZZ
an
Gnd
pulses only present when Intelligent Sensor is turned on. (3.7V p/p) pulses (1.6V p/p)
Le
Pa
lm
1.24V Open Open Gnd 0.59V Open
ei ra
July 2010 LCD TV
81
47LE8500
lm Pa
dr o
ei ra
M2_MOSI Gnd M2_SCLK M3_MOSI M3_SCLK Gnd
Le
*Black to White
an
*Black to White
82
47LE8500
Use speaker out to test for defective Audio Amp IC8801 Note: (Normal, Audio B+) P8800 CONNECTOR "Main" to "Speakers" Pin 1 2 3 4 LABEL SPK-R(-) SPK-R(+) SPK-L(-) SPK-L(+) SBY 0V 0V 0V 0V Run 12.3V 12.3V 12.3V 12.3V Open Open Open Open Diode Check
Mute Pin 25
lm
an
dr o
Pa
ei ra
IC8801
Le
(1)
Main JK8700 Wireless Media Box Dongle Jack (Voltage and Diode Check)
JK8700 "MAIN Board" To "Wireless Media Box Dongle"
Pin 1-6 7 8 9 10 11 12 13 14 15 16 17 18 19-20 Label *24V Detect Interrupt Gnd n/c Gnd I2C_SCL I2C_SDA Gnd Wireless_RX Wireless_TX Gnd IR Gnd STBY 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V Run 24V 0.3V 3.3V Gnd 3.3V Gnd 3.3V 3.3V Gnd 3.3V 3.3V Gnd Gnd 3.3V Diode Check 0.98V 0.98V 1.2V Gnd Gnd 1.1V
JK8700 Jack
lm
ei ra
1.02V 1.02V Gnd 1.17V 1.22V Gnd 1.37V Gnd Diode Mode values taken with all Connectors Removed
Voltages with Wireless Media Box Dongle plugged in. Use Media Box Dongle side to read voltages. Remove cover, (see Wireless Media Box training manual for details). *24V Switched from Q8701 Drain Back side of the board. Q8701 turned on by Q8700 front side of the board. Q8700 turned on by Microprocessor pin 38.
Le
an
0.67V
dr o
Pa
84
47LE8500
The Key board is routed to the IR board via CON2 and output on CON1 Key 1 and Key 2 lines, (Key 1 pin 4 and Key 2 pin 5). Arriving at P8200 pins 4 and 5 on the Main Board. Then to the Microprocessor 25 and 26 lines.
Le
an
The Front Power LEDs are controlled by these same Clock and Data lines which communicate with the LED Driver IC U1 on the Soft Touch Key board.
dr o
The Intelligent Sensor communicates with the Micro/Video Processor IC900 BCM Chip via clock and data lines SCL1 and SDA1 arriving on connector CON1 from P8200 pins 1 and 2 on the Main board.
Pa
The IR pulses (1.6V p/p) CON1 pin 9 are sent to P8200 on the Main board and on to the Microprocessor (IC8101) via pin 16.
lm
The IR (Infrared) remote receiver can be measured (1.57V) at pin 9 of connector CON1 or P8200 on the Main board in Stand-By. During run pin 9 reads (1.54V).
ei ra
85
47LE8500
p/n EBR64966401
CON2
dr o
Pa
lm
ei ra
Le
an
P100
CON1
To Main Board
86
47LE8500
Front Board Connectors CON1, CON2 and CON3 Voltage and Diode Check
CON1 "Front IR" to P8200 " MAIN" Pin 1 2 3 4 5 6 7 8 9 10 11 12
(1)
CON2 "Front IR" to Soft Touch Key Board" Diode Check Open Open Gnd Open Open Open Gnd Open Open Gnd Open Open Pin 1 2 3 4 5 6 7 8 STBY 3.45V 0V Gnd Run 3.36V 1.63V Gnd 3.3V 3.28V Gnd 3.36V 3.36V Diode Check Open Open Gnd Open Open Gnd Open Open
Label
(1) (1)
STBY 3.45V 3.45V Gnd 3.29V 3.29V 3.45V Gnd 0V 1.57V Gnd 0V 0V
Run 3.45V 3.45V Gnd 3.29V 3.29V 3.45V Gnd 0V 1.54V Gnd 0V 3.3V
SCL SDA
lm
Pin 1 2 3 4
Pa
IR
+3.3V_Normal LED_R/BUZZ
an
Gnd
dr o
CON3 "Front IR" to LG Logo Board" STBY 3.45V Gnd 1.36V Gnd Run 3V Gnd 0.6V Gnd Diode Check 1.5 Gnd 0 Gnd
Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p) (2) IR pulses (1.6V p/p) Diode Mode values taken with all Connectors Removed
Le
ei ra
3.3V Gnd 3.45V 3.45V 3.28V
87
47LE8500
The 47LE8500 contains the Invisible Speaker system. The Full Range Speakers point downward, so there is no front viewable speaker grill or air ports.
Top View
Side View
Front View
Le
an
dr o
July 2010 LCD TV
Pa
lm
ei ra
Installed
88
47LE8500
Le
an
dr o
The Adobe version of this Training Manual allows the viewer to zoom in and out making reading of the small text easier. This Power Point shows a graphical representation of the 11 X 17 foldout page so clarity is limited.
Pa
lm
ei ra
This section shows the 11X17 foldout thats available in the Paper and Adobe version of the Training Manual.
89
47LE8500
Diode
STBY 0V GND 0V 0V
11 12 13 14
P-DIM I-C
(2)
n/c ERROR
(2)
Note: If a particular block is exhibiting a dimmer level that the other or the overall brightness seems dim, be sure to first check the customers Menu setting for Backlights. Raise the percentage and see if the overall brightness returns to normal. If not, 1st: Check the P-DIM level, it should rise with the percentage shown on screen. 100%, 3.3V. Follow the PDIM signal all the way to each Inverter. 2nd: Turn off the set and unplug the connector to the Inverters coming from the Main board. If the brightness returns to normal, the Main board is defective.
CN22
Each connector (27 total) to the LED Blocks (216) have two pins delivering B+ 13V and 8 Drive Signals To force a Block to turn on, simple ground the pin providing the 13V source is present.
V73~V80
V105~V112
U103
C BE
F101 12A/65V
+ -
Q108 E Q109E C B
C B
Q12
Q3 Q106
24.6V U101
CN21 V113~V120
Q105 1 18.15V 2 24.6V 3 12.8V Q106 5V 1 2 12.8V 3 Gnd
C101
Q103
C E B
C151
A0948 1050 C
U5 Y501 8Mhz
B
CN10
C E Q101 B E C B
V41~V48
P205
P201
D201
C = 3.45V A1/A2 = 0V A1 C A2
Q5 / Q8 5V 1 2 12.9V Gnd 3
CN101
Q102
13V 12.8V
U4 U501
Q105 13V
L206 N/C
Q501
E C
CN103
U3
CN20
ei ra
CN9
Q1 C E B B E C Q2
C B E
Q16 Q4
C98
A0950 1050 C
CN4
V49~V56
T102
T101
A1 A2
12.96V Q5 Gnd
C E
INVERTER (MAIN)
Both Inverters
CN12
D221
Pa lm
F501 3.15A/250V
p/n: AFB72950101
U4 U3 U11
B E C B E
U7
V29~V136
CN19
V9~V16 P7901
IC9102 Q8005
P8000
IC8005
47uF/450V
47uF/450V
47uF/450V
47uF/450V
Q7 F501 Hot Gnd STBY 159.6V Run 392.6V D102 U102 L102 12.77V Q8
Q11
Q15 U1
Q110
G S D G
U103 13V Q3 C
E B
U501
U10
CN5
CN13
IC9300 SW9300 X9300 25Mhz IC9000 X9000 12Mhz
C89
A0948 1050 C
Q12 + 13V
CN7
L601
DO NOT MEASURE
CN11
8Mhz Y501
8Mhz
Y1
V137~V144 CN18
U9
D607
1 3 2 Q8000 Q8002 Q8004 A IC9103 D AC Q8001 D9101 L8015 G S C A AC 31 31 Q8003 Rubber D9102 C IC8008 L9101 2 2 IC9302 IC8007 L9301 L8905 IC8903 IC8902 IC8003 IC8901 L8904 IC8001 IC8900 IC8002 L8012 Grayed out components are on the back IC602 L8009 IC605 IC606 L8010 L9102 IC603 IC604 P9000 IC8000 IC301 IC302 L8004 USB1
CN29
V25~V32
Pin
C A G D S D603
STBY 0V 0V
CN17
SW8100 Micro Reset SW1000 Video Reset
Le an dr o
CN6
L600 BD101 -
D601
D602
C A
*0.04V~3.2V 1.08V
V145~V152
P9000 Update IC8100 X8101 32.768Khz X8100 10 D8312 SW8100 Mhz IC1000 IC8101 SW1000 Q8308
Q606
Gnd
CN28
V73~V80
G D S
Q605
3.5V
Gnd 0V 0V
*0.04V~3.2V 1.08V
Open
11.9V
1.39V Open
Gnd 0V 0V
P8100
Q8800
D
MICRO IC8004
INV-ON
P-DIM
2.92V 11.9V
1.63V
0V 0V
1.39V Open
*0.18V~0.28V 1.08V
V33~V40
CN5
V81~V88
CN4
16 15
14 13
12 11 STBY 3.5V
V89~V96
(1) PDIM Pin 20 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V. CON3 "IR Board" To "Center Logo Board" Pin STBY Run Diode
4 5 6 7 8
M2_SCLK Gnd
0V
V161~V168
Q8700
M3_MOSI Gnd
0V
IC8700
CN3
B 16 15 14 13
12 11 STBY 3.5V
10 9
+ CX103 RL101
STBY 3.5V 8 7 6 5 A 24V 24V 4 3 24V PWR ON 2 1
0V
0.37V~3.3V 11.9V 0V 0V
10
0V
IC8800 Q200 S
S G G
CN27
RL102
B E C
SK101 AC In
IC8801
n/c n/c 0V
TU700 TDVJ-H031F
Q231 SMPS TEST 1: To Force Power Supply On. Disconnect P8000 on Main board. (A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. (Test Voltage Outputs 12V, 24V to Main and 24V to both Inverters). Remove AC power. Leave the jumper in place. SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (INV-ON). Apply AC power, the Backlights should turn on. Note; If Inverter Main or Secondary is loading down 24V, each Inverter can be run separately: Remove AC and Disconnect P204. When AC is reapplied, the Backlight LEDs on the Right (Back View) should turn on. Remove AC and Disconnect P205 and reinstall P204. When AC is reapplied, the Backlight LEDs on the Left (Back View) should turn on.
ERROR
0V
Open
Gnd 0V
CN15
L8804 L8805
M2_MOSI
*0.04V~3.2V
Q?
IC8200
Gnd
Q8701
IF p Digital Video IF n IF AGC Q702 Reset 3.3V 1.26V Analog Video GND CVBS NC Q701 SIF NC SDA SCL NC NC 5V
V41~V48
HDMI
CN26
CON2
M3_SCLK
0V Gnd
Q8201 Q8205
CON3
IR Receiver Intelligent Sensor
Front IR
CON1
1 2 3 4
*Black to White For Waveforms on P7900 and P7901 See 2nd page of Interconnect.
CN14 V169~V176
P8800
Q8203
P8200
2. NC 1. NC
Q8306 Q8307
V49~V56
0.64V Open
CN25 P8800 "Main" To "Speakers" Pin Label SBY Run 1 SPK-R(-) 0V 12.3V 2 SPK-R(+) 0V 12.3V 3 SPK-L(-) 0V 12.3V 4 SPK-L(+) 0V 12.3V Diode Open Open Open Open P8200 "MAIN Board" To CON1 "IR Board" Pin Label STBY Run Diode Check SCL 3.45V 3.45V Open Intelligent Sensor 1 SDA 3.45V 3.45V Open Intelligent Sensor 2 3 Gnd Gnd Gnd Gnd 4 Key1 3.29V 3.29V 1.9V 5 Key2 3.29V 3.29V 1.9V Stand-by 6 3.5V_ST 3.45V 3.45V 1.24V Pin Label STBY 7 Gnd Gnd 0V 8 LED_LOGO 9 IR 1.57V 10 Gnd Gnd 11 3.3V_Normal 0V 12 LED_BUZZ 0V Run Gnd 0V 1.54V Gnd 3.3V 0V Diode Check Gnd Open Open Gnd 0.59V Open
42LE8500 Inverter Main and Secondary Local Dimming Control Signals Waveforms CN11 INVERTER (MAIN) FROM P7900 MAIN BOARD
Inverter Main CN11 pin 01 Black or White Screen Inverter Main CN11 pin 02 Black Screen Inverter Main CN11 pin 02 White Screen Inverter Main CN11 pin 03 Black Screen Inverter Main CN11 pin 03 White Screen
1V per/div 4MSes 3.66V p/p Inverter Main CN11 pin 05 Black Screen
1V per/div 4MSes 3.70V p/p Inverter Main CN11 pin 05 White Screen
1V per/div 4MSes 4.22V p/p Inverter Main CN11 pin 06 Black or White Screen
1V per/div 4MSes 3.70V p/p 1V per/div 4MSes 3.96V p/p Inverter Main CN11 pin 08 Black or White Screen Inverter Main CN11 pin 09 Black Screen
1V per/div 4MSes 3.66V p/p Inverter Main CN11 pin 09 White Screen
1V per/div 4MSes 3.98V p/p Inverter Main CN11 pin 11 Black Screen
1V per/div 4MSes 3.98V p/p Inverter Main CN11 pin 11 White Screen
Pa lm
ei ra
Le an dr o
Inverter Secondary CN103 pin 02 Black Screen
47LE8500 MAIN (FRONT SIDE) SIMICONDUCTORS IC700 (+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.26V (Out) [3] 3.3V (In) SOC Reset Pin Generator [1] 3.32V (In) [2] 0V (Gnd) [3] 3.3V (Out) 5V Regulator for USB 11.79V (In) 5V (Out) 5V (Out) 10.5V 3.3V 0.8V 4.99V 0V (Gnd) D1.2V and A1.2V Regulator 0V (Gnd) 3.3V 0V (Gnd) 1.2V 3.3V n/c 4.46V 3.3V 3.3V 3.3V 1.2V Gnd 3.3V 0.8V IC8002 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC8003 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8004 Pin [1] [2] [3] [4] [5] [6] [7] [8] (D1.8V) Regulator IC8005 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+3.3V_NORMAL) IC8902 Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.36V (PWR On/Off2 C 3.36V (Out) 3.36V (Out) Power Det Gen (+12V and +3.5V) 0V (Gnd) 3.6V (In) 3.5V (Out) IC8903 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC9100 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] (+1.26V_MEMC) IC9102 Regulator Pin 0V (Gnd) [1] 11.8V (In) [2] 0V (Gnd) [3] 0.8V [4] 0.7V [5] 3.36V (PWR On/Off2 [6] 1.3V (Out) [7] 1.3V (Out) [8] [9] (+3.3V_MEMC) [10] Regulator [11] 0V (Gnd) [12] 11.8V (In) [13] 0V (Gnd) [14] 0.8V [15] 0.8V [16] 3.36V (PWR On/Off2 Ctl) 3.3V (Out) IC9300 3.3V (Out) Pin [1] P-GAMMA [2] Chip [3] 3.3V 0V (Gnd) IC9302 3.3V (In) Pin 0V (Gnd) [1] 6.8V [2] 6.8V [3] 15.3V [4] 15.3V [5] n/c [6] 13.47V [7] 12.75V [8] 11.8V 10V Q8001 5.96V Pin 4.06V B 15.3V C 0V E 2.96V 2.33V 3.3V (In) DC to DC HVDD T-CON 0V (Gnd) 11.72V (In) 11.72V (In) 3.25V 3.2V 0V 0V 11.7V 0V (Gnd) 1.13V 0V (Gnd) 0V (Gnd) 0V (Gnd) 7.7V 7.7V (HVDD) 0V (Gnd) Reset for LG5111 3.32V (In) 0V (Gnd) 3.34V (Out) Q8003 PANEL_VCC Pin Control 2nd Driver B 0.679V C 0V E Gnd PANEL_VCC Pin Switch S 11.8V (In) G 1.8V (Enable) D 11.8V (Out) INV_ON Pin Driver B 0V (INV ON) En C 3.1V (Out) E Gnd IR Buffer 2nd Q8800 AMP_MUTE Pin Pin 25 IC8801 B 0V C 3.336V E Gnd VGH/VDD Pin Rectifyer A 15.4V AC 22.2V C 27.4V (VGH) VGL/VCC Pin Rectifyer A (-5V VGL) AC (-1.9V) C 0V
IC1000
5V 3.34V (In) 1.8V (Out) Gnd Gnd 0.9V 0.9V 1V 2.38V 3.36V (PWR On/Off1 Ctl) IC8007
Q8004
D9101
IC8000 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8001 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
Pa lm
(+5V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) IC8008 Power Det Gen 0.8V Pin (+24V) 0.86V [1] 0V (Gnd) 3.37V (PWR On/Off2 Ctl) [2] 3.6V (In) 5V (In) [3] 3.7V (Out) 5V (In) IC8800 (+1.8V_AMP) A2.5V Regulator Pin Regulator for USB [1] 0V (Gnd) n/c [2] 1.8V (Out) 3.26V (In) [3] 3.295V (In) 3.26V (In) n/c IC8901 (+1.5V_MEMC) n/c Pin Regulator 2.55V (Out) [1] 0V (Gnd) 0.8V [2] 1.5V (Out) 0V (Gnd) [3] 3.3V (In)
Q8005
D9102
Q8200 Pin B C E Gnd Q8201 Pin B 0V C 3.3V E Gnd Q8306 Pin B 0V C 3.3V E Gnd Q8307
ei ra
PANEL_VCC
Control 1st Driver
(1.8V_L/Dimming) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.76V 3.34V (PWR On/Off2 Ctl) 1.8V (In) 1.8V (In)
IR Buffer 1st
HDMI Det
47LE8500 MAIN (BACK SIDE) SIMICONDUCTORS IC602 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8100 Pin [1] [2] [3] [4] [5] [6] [7] [8] D1.8V Regulator 0V (Gnd) 3.29V (PWR On/Off1 Ctl) 0.9V (DDR_VTT) 0.93V 1.83V 3.38V (In) 1.8V (Out) 0.91V (DDR_VTT) EEPROM Micro 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 0V (Gnd) 3.37V IC8200 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] RS232 Routing 0V 0V 0V 0V 0V (-5.47V) n/c (5.59V) n/c (0V) n/c (3.3V) n/c (0.2V) n/c (3.3V) 3.35V 0V (-5.47V) 0V (Gnd) 3.37V
Le an dr o
0V 0.68V Gnd
IC8400
Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
RGB H/V Sync 1.9V 1.9V 4.4V 0V 0.9V n/c (4.5V) 0V (Gnd) n/c (4.5V) n/c (1.9V) n/c (1.9V) n/c (4.5V) 0.9V 0.9V 5V
IC8401
EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 0.7V 4.1V 4.5V 4.5V (In)
IC9303 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q200
EEPROM for LG5111 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 3.34V 3.37V (In)
Q901
FLASH_WP Pin for IC901 B 0V (Flash_WP) C 3.36V E Gnd RL_ON (PWR_On) Pin 1st Driver B 0.66V C 0V E Gnd PWR_ON Pin Switch [1] 3.36V (In) [2] 0V [3] 3.3V (Out) HDMI 2 Det
Q8308 Pin [B] [G] [S] [D] D8312 Pin A1 C A2 D8306, 7, 9 Pin A1 C A2
Q8000
CEC Remote HDMI CEC 2.72V 2.73V 3.27V 3.37V 3.5V Pull Up HDMI CEC 0V 3.26V 3.2V 5V Pull Up Routing HDMI SCL/SDA 5.04V 4.58V 0V
IC9000 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Serial Flash T-CON 0.06V 0.67V 3.3V (In) 0V (Gnd) 0V 0.34V 3.31V (In) 3.34V (In)
(1.8V_HDMI) Pin Switch S 1.83V (Out) G 3.35V (PWR On/Off2 Ctl) D 1.83V (In) Tuner SIF Pin (Sound) Buffer B 0.16V C Gnd E 0.83V Tuner Video Pin (Analog) Buffer B 2.05V C 2.75V E Gnd
Q8002
Q701
Q702
HDMI 3 Det
an
dr o
This concludes the 47LE8500 training session.
Le
Pa
lm
ei ra