Escolar Documentos
Profissional Documentos
Cultura Documentos
KA3842A KA3842AM
PIN CONNECTION
FEATURES
Low Start-Up Current Maximum Duty Cycle U/V Lockout With Hysteresis Operating Freguency Up To 500khz
SO-8 DIP-8
ordering information
Device KA3842AM KA3842AMM KA3842AN KA3842AMN Package SO-8 SO-8 DIP-8 DIP-8 Operating temperature 0 to +700C " " "
BLOCK DIAGRAM
KA3842A/KA3842AM
Electrical characteristics (*VCC=15V, RT=10k, CT=3.3nF, TA=00C to +700C, unless otherwise specified) Characteristics
Reference Section Reference Output Voltege Line Regulation Load Regulation Short Circit Output Current Oscillator Section Oscillation Freguency Frequency Change with Voltage Oscillator Amplitude Error Amplifier Section Input Bias Current Input Voltage Open Loop Voltage Gain Power Supply Rejection Ratio Output Sink Current Output Source Current High Output Voltage Low Output Voltage Current Sense Section Gain Maximum Input Signal Power Supply Rejection Ratio Input Bias Current Output Section Low Output Voltage High Output Voltage Rise Time Fall Time
Symbol
VREF VREF VREF ISC f f/VCCF V(OSC) IBIAS VI(E.A) GVO PSRR ISINK ISOURCE VOH VOL GV VI(MAX) PSRR IBIAS VOL VOH tR tF ISINK ISINK ISINK ISINK
Test Condition
TJ = 25C, IREF = 1 mA 12V VCC 25 V 1 mA IREF 20mA TA = 25C TJ = 25C 12V VCC 25 V
Min
4.9
Typ
5.0 6.0 6.0 -100
Max
5.1 20 25 -180 57 1.0
Unit
V mV mA KHz % Vp-p
47
-2 2.58
V1 = 2.5V 2V V0 4V 12V VCC 25 V V2 = 2.7V, V1 = 1.1V V2 = 2.3V, V1 = 5V V2 = 2.3V, RL = 15K to GND V2 = 2.7V, RL = 15K to PIN 8 (Note 1 & 2) V1 = 5V (Note1) 12V VCC 25 V (Note 1)
A V dB mA mA V
2.85 0.9
= = = =
20 mA 200 mA 20 mA 200 mA
13 12
nS
UnderVoltage Lockout Section Start Theshold VTH(ST) Min. Operating Voltage (After Turn On) PWM Section Max. Duty Cycle Min. Duty Cycle Total Standby Current StartUp Current Operating Supply Current Zener Voltage VOPR(min)
V V
95
97
100 % 0
0.17 14 38
0.3 17
mA
30
* Adjust VCC above the start threshold before setting at 15V Note 1: Parameter measured at trip point of lath with V2=0 Note 2: Gain defined as A=V1/V3 ; 0 V3 0.8V Note 3: These parameters, although guaranteed, are not 100% tested in production.
KA3842A/KA3842AM
Pad Location
KA3842A/KA3842AM
DIM. MIN. A a1 a2 a3 b b1 C c1 D (1) E e e3 F (1) L M S 3.8 0.4 4.8 5.8 1.27 3.81 4.0 1.27 0.6 8 (max.) 0.15 0.016 0.65 0.35 0.19 0.25 0.1 mm TYP. MAX. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 0.026 0.014 0.007 0.010 0.004 MIN. inch TYP. MAX. 0.069 0.010 0.065 0.033 0.019 0.010 0.020
45 (typ.) 5.0 6.2 0.189 0.228 0.050 0.150 0.157 0.050 0.024 0.197 0.244
KA3842AM KA3842AMM
SO8
(1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch).
KA3842A/KA3842AM
B
1 4
NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC 10_ 0.030 0.040
F
NOTE 2
A L
C T
SEATING PLANE
J N D K
M
M T A B
G 0.13 (0.005)
M M
KA3842AN KA3842AMN
Attention: M=10
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.