Escolar Documentos
Profissional Documentos
Cultura Documentos
4-2003
ANSI/ASQ Z1.4-2003
Prepared by
The Statistics Subcommittee of the Accredited
Standards Committee Z1 on Quality, Environment,
Dependability and Statistics
Secretariat
American Society for Quality
Abstract
Sampling Procedures and Tables for Inspection by Attributes is an acceptance sampling system to be used with switching
rules on a continuing stream of lots for AQL specified. It provides tightened, normal, and reduced plans to be applied for
attributes inspection for percent nonconforming or nonconformities per 100 units.
AMERICAN NATIONAL STANDARD: An American national Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the
consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes,
or procedures not conforming to the standard. American National Standards are subject to periodic review and users are
cautioned to obtain the latest editions.
CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the
American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later
than five years from the date of publication. Purchasers of American National Standards may receive current information
on all standards by calling or writing the American National Standards Institute.
Published by
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON
MILWAUKEE, WISCONSIN 53203
2003 by the AMERICAN SOCIETY FOR QUALITY
No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the
prior written permission of the publisher.
Printed in the United States of America
Foreword
(This foreword is not a part of the American National
StandardSampling Procedures and Tables for Inspection
by Attributes, Z1.4-2003)
Note 1: Other than 3), 7), and 8) above, all tables, table
numbers and procedures used in MIL-STD-105E (which
was cancelled in 1995) have been retained.
Suggestions for improvement of this standard are welcomed. Send your comments to the sponsor, ASQ, 600
North Plankinton Avenue, Milwaukee, WI 53203.
iii
ANSI/ASQ Z1.4-2003
Table of Contents
Paragraph
Page
1. SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. DEFINITIONS AND TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. PERCENT NONCONFORMING AND NONCONFORMITIES PER
HUNDRED UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. ACCEPTANCE QUALITY LIMIT (AQL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5. SUBMISSION OF PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6. ACCEPTANCE AND NON-ACCEPTANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7. DRAWING OF SAMPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
8. NORMAL, TIGHTENED, AND REDUCED INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9. SAMPLING PLANS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10. DETERMINATION OF ACCEPTABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11. SUPPLEMENTARY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tables
Table I
Table II-A
Table II-B
Table II-C
Table III-A
Table III-B
Table III-C
Table IV-A
Table IV-B
Table IV-C
Table V-A
Table V-B
Table VI-A
Table VI-B
Table VII-A
Table VII-B
Table VIII
Table IX
Table X-A
Table X-B
Table X-C
ANSI/ASQ Z1.4-2003
Table X-D
Table X-E
Table X-F
Table X-G
Table X-H
Table X-J
Table X-K
Table X-L
Table X-M
Table X-N
Table X-P
Table X-Q
Table X-R
Table X-S
Table XI
vi
a. End items.
d. Materials in process.
e. Supplies in storage.
f. Maintenance operations.
NONCONFORMITY: A departure of a quality characteristic from its intended level or state that occurs
with severity sufficient to cause an associated
product or service not to meet a specification
requirement.
g. Data or records.
h. Administrative procedures.
These plans are intended primarily to be used for a continuing series of lots or batches. The plans may also be used for
the inspection of isolated lots or batches, but, in this latter
case, the user is cautioned to consult the operating characteristic curves to find a plan which will yield the desired protection (see 11.6).
1.3 INSPECTION. Inspection is the process of measuring, examining, testing, or otherwise comparing the unit of
product (see 1.5) with the requirements.
1
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
Number nonconforming
100
Number of units inspected
The AQL alone does not describe the protection to the consumer for individual lots or batches, but more directly relates
to what is expected from a series of lots or batches provided
the provisions of this standard are satisfied.
4.5 SPECIFYING AQLs. The AQL to be used will be designated in the contract or by the responsible authority.
Different AQLs may be designated for groups of nonconformities considered collectively, or for individual nonconformities. For example, Group A may include nonconformities
of a type felt to be of the highest concern for the product or
service and therefore be assigned a small AQL value; Group
B may include nonconformities of the next higher degree of
concern and therefore be assigned a larger AQL value than
for Group A and smaller than that of Group C, etc. The classification into groups should be appropriate to the quality
4.1 USE. The AQL together with the Sample Size Code
Letter, is used for indexing the sampling plans provided herein.
4.2 DEFINITION. The AQL is the quality level that is the
worst tolerable process average when a continuing series of
lots is submitted for acceptance sampling.
Note: The use of the abbreviation AQL to mean Acceptable
Quality Level is no longer recommended.
2
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
5.2 FORMATION OF LOTS OR BATCHES. The product shall be assembled into identifiable lots, sublots, batches,
or in such other manner as may be prescribed (see 5.4). Each
lot or batch shall, as far as is practicable, consist of units of
product of a single type, grade, class, size, and composition,
manufactured under essentially the same conditions, and at
essentially the same time.
3
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
7.4 DOUBLE OR MULTIPLE SAMPLING. Where double or multiple sampling is to be used, each sample shall be
selected over the entire lot or batch.
8. NORMAL, TIGHTENED AND REDUCED
INSPECTION
8.1 INITIATION OF INSPECTION. Normal inspection
will be used at the start of inspection unless otherwise
directed by the responsible authority.
The supplier may be required at the discretion of the responsible authority to inspect every unit of the lot or batch for
designated classes of nonconformities. The right is reserved
to inspect every unit submitted by the supplier for specified
nonconformities, and to reject the lot or batch immediately,
when a nonconformity of this class is found. The right is
reserved also to sample, for specified classes of nonconformities, lots or batches submitted by the supplier and to reject
any lot or batch if a sample drawn therefrom is found to contain one or more of these nonconformities.
8.2 CONTINUATION OF INSPECTION. Normal, tightened or reduced inspection shall continue unchanged on
successive lots or batches except where the switching procedures given below require change.
8.3 SWITCHING PROCEDURES.
8.3.1 NORMAL TO TIGHTENED. When normal
inspection is in effect, tightened inspection shall be instituted when 2 out of 5 or fewer consecutive lots or batches
have been non-acceptable on original inspection (i.e., ignoring resubmitted lots or batches for this procedure).
7. DRAWING OF SAMPLES
7.1 SAMPLE. A sample consists of one or more units of
product drawn from a lot or batch, the units of the sample
being selected at random without regard to their quality. The
number of units of product in the sample is the sample size.
a. The preceding 10 lots or batches (or more, as indicated by the note to Table VIII) have been on normal inspection and all have been accepted on
original inspection; and
4
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
b. The total number of nonconforming units (or nonconformities) in the samples from the preceding 10
lots or batches (or such other number as was used
for condition a above) is equal to or less than the
applicable limit number given in Table VIII (see
8.5). If double or multiple sampling is in use, all
samples inspected should be included, not first
samples only; and
9.5 TYPES OF SAMPLING PLANS. Three types of sampling plans: Single, Double and Multiple, are given in Tables
II, III, and IV, respectively. When several types of plans are
available for a given AQL and code letter, any one may be
used. A decision as to type of plan, either single, double, or
multiple, when available for a given AQL and code letter,
will usually be based upon the comparison between the
9. SAMPLING PLANS
9.1 SAMPLING PLAN. A sampling plan indicates the
number of units of product from each lot or batch which are
5
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
10.1.1 SINGLE SAMPLING PLAN. The number of sample units inspected shall be equal to the sample size given by
the plan. If the number of nonconforming units found in the
sample is equal to or less than the acceptance number, the lot
or batch shall be considered acceptable. If the number of
nonconforming units is equal to or greater than the rejection
number, the lot or batch shall be considered not acceptable.
10.1.2 DOUBLE SAMPLE PLAN. The number of sample
units first inspected shall be equal to the first sample size
given by the plan. If the number of nonconforming units
found in the first sample is equal to or less than the first
acceptable number, the lot or batch shall be considered
acceptable. If the number of nonconforming units found in
the first sample is equal to or greater than the first rejection
number, the lot or batch shall be considered not acceptable.
If the number of nonconforming units found in the first sample is between the first acceptance and rejection numbers, a
second sample of the size given by the plan shall be
inspected. The number of nonconforming units found in the
first and second samples shall be accumulated. If the cumulative number of nonconforming units is equal to or less than
the second acceptance number, the lot or batch shall be considered acceptable. If the cumulative number of nonconforming units is equal to or greater than the second rejection
number, the lot or batch shall be considered not acceptable.
6
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
plan. AOQL values are given in Table V-A for each of the
single sampling plans for normal inspection and in Table V-B
for each of the single sampling plans for tightened inspections. AOQL values for ANSI Z1.4 scheme performance are
given in Table XI subject to the restrictions of 11.1. They
show the average outgoing quality limits for scheme performance when using single sampling. AOQL will be
slightly higher when the limit numbers for reduced inspection are not used under Option 8.5.
Note that the operating characteristic curve for scheme performance is approximately that of the normal plan for low
levels of percent nonconforming and that the tightened plan
for high levels of percent nonconforming. Use of the
reduced plan increases scheme probability of acceptance
only for extremely low levels of percent nonconforming.
7
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
ANSI/ASQ Z1.4-2003
with the AQL and Inspection Level specified for the inspection of a series of lots or batches. For example, if an LQ of
5 percent is desired for individual lots with an associated Pa
of 10 percent or less, then if an AQL of 1.5 percent is designated for inspection of a series of lots or batches. Table VI
indicates that the minimum sample size must be that given
by Code Letter M.
8
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
SWITCHING
RULES
REDUCED
Preceding 10 Lots
Accepted, with
Total Nonconforming
less than Limit Number
(Optional), and
Production Steady,
and
Approved by
Responsible Authority
FIGURE 1
NORMAL
START
5 Consecutive
Lots Accepted
2 of 5 or fewer
Consecutive Lots are
Not Accepted
Discontinue
Inspection
Under Z1.4
TIGHTENED
CODE
LETTERS
10
to
to
to
to
to
to
to
to
to
to
to
and
151
281
501
1201
3201
10001
35001
150001
500001
to
to
to
26
51
91
2
9
16
3200
10000
35000
280
500
1200
50
90
150
8
15
25
150000
500000
over
D
D
D
C
C
C
B
B
C
A
B
B
A
A
A
S-1
E
E
E
D
D
D
C
C
C
B
B
B
A
A
A
S-2
G
G
H
E
F
F
D
D
E
B
C
C
A
A
B
S-3
J
J
K
G
G
H
E
E
F
C
C
D
A
A
B
S-4
L
M
N
H
J
K
E
F
G
C
C
D
A
A
B
N
P
Q
K
L
M
G
H
J
D
E
F
A
B
C
II
P
Q
R
L
M
N
H
J
K
E
F
G
B
C
D
III
SINGLE
NORMAL
PLANS
11
2
3
5
8
13
20
32
50
80
125
200
315
500
800
1250
2000
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
1 2
2 3
3 4
5 6
1 2
2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 45
3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 45
5 6 7 8 10 11 14 15 21 22
3 4 5 6 7 8 10 11 14 15 21 22
5 6 7 8 10 11 14 15 21 22
7 8 10 11 14 15 21 22
1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31
2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 45
3 4 5 6 7 8 10 11 14 15 21 22 30 31 44 45
3 4 5 6 7 8 10 11 14 15 21 22
5 6 7 8 10 11 14 15 21 22
7 8 10 11 14 15 21 22
1 2
1 2 2 3
2 3 3 4
1 2
1 2 2 3
1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22
2 3 3 4 5 6 7 8 10 11 14 15 21 22
1 2
1 2 2 3
1 2 2 3 3 4
2 3 3 4 5 6 7 8 10 11 14 15 21 22
1 2 2 3
1 2 2 3 3 4
1 2 2 3 3 4 5 6
0 1
0 1
0 1
0 1
= Use the first sampling plan below the arrow. If sample size equals, or exceeds, lot size, carry out 100 percent inspection.
1 2
0 1
Re = Rejection number.
Ac = Acceptance number.
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
Sample
size
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100 150 250 400 650 1000
code
size
letter
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
Acceptance Quality Limits, AQLs, in Percent Nonconforming Items and Nonconformities per 100 Items (Normal Inspection)
SINGLE
TIGHTENED
PLANS
12
2
3
5
8
13
20
32
50
80
125
200
315
500
800
1250
2000
3150
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
1 2
1 2 2 3
1 2
2 3
3 4
1 2 2 3
2 3 3 4
3 4 5 6
8 9 12 13 18 19
2 3 3 4 5 6 8 9 12 13 18 19
3 4 5 6 8 9 12 13 18 19
5 6 8 9 12 13 18 19
3 4 5 6 8 9 12 13 18 19 27 28 41 42
5 6 8 9 12 13 18 19 27 28 41 42
8 9 12 13 18 19
2 3 3 4 5 6 8 9 12 13 18 19
3 4 5 6 8 9 12 13 18 19
5 6 8 9 12 13 18 19
1 2
1 2 2 3
1 2 2 3 3 4 5 6 8 9 12 13 18 19
1 2 2 3 3 4 5 6 8 9 12 13 18 19
1 2 2 3 3 4 5 6 8 9 12 13 18 19
0 1
0 1
1 2
1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28
1 2 2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
2 3 3 4 5 6 8 9 12 13 18 19 27 28 41 42
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
1 2
1 2
1 2 2 3
1 2 2 3 3 4
0 1
1 2 2 3 3 4 5 6
0 1
Re = Rejection number.
Ac = Acceptance number.
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
Sample
size
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100 150 250 400 650 1000
code
size
letter
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
SINGLE
REDUCED
PLANS
13
2
2
2
3
5
8
13
20
32
50
80
125
200
315
500
800
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
0 2
1 3 1 4 2 5 3 6
0 2 1 3
0 2 1 3 1 4
0 2 1 3 1 4 2 5
0 1
0 2
0 2 1 3
0 2 1 3 1 4
5 8 7 10 10 13
1 4 2 5
2 5 3 6
3 6 5 8
0 2
0 2 1 3
1 3 1 4
2 5 3 6 5 8 7 10 10 13 14 17 21 24
3 6 5 8 7 10 10 13 14 17 21 24
5 8 7 10 10 13
1 2 2 3 3 4 5 6 7 8 10 11 14 15 21 22 30 31
1 3 2 4 3 5 5 6 7 8 10 11 14 15 21 22 30 31
1 4 2 5 3 6 5 8 7 10 10 13 14 17 21 24
3 6 5 8 7 10 10 13
5 8 7 10 10 13
7 10 10 13
1 3 1 4
1 4 2 5
2 5 3 6
0 2
0 2 1 3
3 6 5 8 7 10 10 13
5 8 7 10 10 13
7 10 10 13
1 3
1 4
2 5
0 2
1 4 2 5 3 6 5 8 7 10 10 13
2 5 3 6 5 8 7 10 10 13
3 6 5 8 7 10 10 13
0 2 1 3 1 4 2 5
0 2 1 3 1 4 2 5 3 6
1 3 1 4 2 5 3 6 5 8
0 1
0 1
0 1
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
0 2
0 1
= If the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot, but reinstate normal inspection (see 10.1.4).
Re = Rejection number.
Ac = Acceptance number.
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
Sample
size
Sample 0.010 0.015 0.025 0.040 0.065 0.10 0.15 0.25 0.40 0.65 1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100 150 250 400 650 1000
code
size
letter
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
Sample size
code letter
DOUBLE
NORMAL
PLANS
14
Sample
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
Sample size
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
0
1
2
2
0
1
0
3
2
2
3
4
0
1
0
3
1
4
2
2
3
4
4
5
0
1
0
3
1
4
2
6
2
2
3
4
4
5
5
7
0
1
0
3
1
4
2
6
3
8
2
2
3
4
4
5
5
7
7
9
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
8 9
5 9
12 13
7 11
18 19
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
1
0
3
1
4
2
6
3
8
5
12
7
18
11
26
2
2
3
4
4
5
5
7
7
9
9
13
11
19
16
27
0
3
1
4
2
6
3
8
5
12
7
18
11
26
3
4
4
5
5
7
7
9
9
13
11
19
16
27
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
2
4
3
6
5
10
8
16
13
26
20
40
32
64
50
100
80
160
125
250
200
400
315
630
500
1000
800
1600
1250
2500
0.15
40
65
100
150
250
400
650
1000
+ = Use corresponding single sampling plan or double sampling plan for code letter B below.
Re = Rejection number.
1
4
2
6
3
8
5
12
7
18
11
26
4
5
5
7
7
9
9
13
11
19
16
27
+
2
6
3
8
5
12
7
18
11
26
5
7
7
9
9
13
11
19
16
27
+
3
8
5
12
7
18
11
26
7
9
9
13
11
19
16
27
+
5
12
7
18
11
26
17
37
9
13
11
19
16
27
22
38
+
7
18
11
26
17
37
25
56
11
19
16
27
22
38
31
57
11
26
17
37
25
56
16
27
22
38
31
57
17
37
25
56
+
22 25 31
38 56 57
31
57
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
Ac = Acceptance number.
2
2
3
3
5
5
8
8
13
13
20
20
32
32
50
50
80
80
125
125
200
200
315
315
500
500
800
800
1250
1250
Cumulative
sample size
15
Sample size
code letter
DOUBLE
TIGHTENED
PLANS
2
4
3
6
5
10
8
16
13
26
20
40
32
64
50
100
80
160
125
250
200
400
315
630
500
1000
800
1600
1250
2500
2000
4000
Sample size
2
2
3
3
5
5
8
8
13
13
20
20
32
32
50
50
80
80
125
125
200
200
315
315
500
500
800
800
1250
1250
2000
2000
Sample
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
0
1
2
2
0
1
2
2
0
1
0
3
2
2
3
4
0
1
0
3
1
4
2
2
3
4
4
5
0
1
0
3
1
4
2
6
2
2
3
4
4
5
5
7
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
0 2
1 2
0 3
3 4
1 4
4 5
2 5
6 7
3 7
11 12
6 10
15 16
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2
2
3
4
4
5
5
7
7
12
10
16
14
24
0
1
0
3
1
4
2
6
3
11
6
15
9
23
2 0 3 1
2 3 4 4
3 1 4 2
4 4 5 6
4 2 5 3
5 6 7 11
5 3 7 6
7 11 12 15
7 6 10 9
12 15 16 23
10 9 14
16 23 24
14
24
+ = Use corresponding single sampling plan or double sampling plan for code letter B below.
Re = Rejection number.
Ac = Acceptance number.
4 2 5 3 7 6
5 6 7 11 12 15
5 3 7 6 10 9
7 11 12 15 16 23
7 6 10 9 14 15
12 15 16 23 24 34
10 9 14 15 20 23
16 23 24 34 35 52
14
24
10
16
14
24
20
35
29
53
9
23
15
34
23
52
14
24
20
35
29
53
15
34
23
52
+
20 23 29
35 52 53
29
53
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
Cumulative
sample size
Sample size
code letter
DOUBLE
REDUCED
PLANS
16
Sample
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
First
Second
Sample size
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
0
0
2
2
0
0
0
0
2
2
3
4
0
0
0
0
0
1
2
2
3
4
4
5
0
0
0
0
0
1
0
3
2
2
3
4
4
5
4
6
0
0
0
0
0
1
0
3
1
4
2
2
3
4
4
5
4
6
5
7
0
0
0
0
0
1
0
3
1
4
2
6
2
2
3
4
4
5
4
6
5
7
7
9
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
0 2
0 2
0 3
0 4
0 4
1 5
0 4
3 6
1 5
4 7
2 7
6 9
3 8
8 12
5 10
12 16
40
65
100
150
+
+
+ = Use corresponding single sampling plan or double sampling plan for code letter D below.
= If, after the second sample, the acceptance number has been exceeded, but the rejection number has not been reached,
accept the lot, but reinstate normal inspection (see 10.1.4).
Re = Rejection number.
0 2 0 3 0 4 0 4 1 5 2 7 3 8 5
0 2 0 4 1 5 3 6 4 7 6 9 8 12 12
0 3 0 4 0 4 1 5 2 7 3 8 5 10 7
0 4 1 5 3 6 4 7 6 9 8 12 12 16 18
0 4 0 4 1 5 2 7 3 8 5 10
1 5 3 6 4 7 6 9 8 12 12 16
0 4 1 5 2 7 3 8 5 10
3 6 4 7 6 9 8 12 12 16
1 5 2 7 3 8 5 10
4 7 6 9 8 12 12 16
2 7 3 8 5 10
6 9 8 12 12 16
3 8 5 10
8 12 12 16
5 10
12 16
= Use first sampling plan below arrow. If sample size equals or exceeds lot or batch size, do 100 percent inspection.
2
4
3
6
5
10
8
16
13
26
20
40
32
64
50
100
80
160
125
250
200
400
315
630
500
1000
0.15
250
400
650
1000
10 7 12 11 17
16 18 22 26 30
12 11 17
22 26 30
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
Ac = Acceptance number.
2
2
3
3
5
5
8
8
13
13
20
20
32
32
50
50
80
80
125
125
200
200
315
315
500
500
Cumulative
sample size
17
A
B
C
Sample size
code letter
MULTIPLE
NORMAL
PLANS
2
4
6
8
10
12
14
3
6
9
12
15
18
21
5
10
15
20
25
30
35
8
16
24
32
40
48
56
13
26
39
52
65
78
91
20
40
60
80
100
120
140
Sample size
2
2
2
2
2
2
2
3
3
3
3
3
3
3
5
5
5
5
5
5
5
8
8
8
8
8
8
8
13
13
13
13
13
13
13
20
20
20
20
20
20
20
Sample
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
1
1
2
2
2
2
3
3
3
3
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
# 2
# 2
0 2
0 3
1 3
1 3
2 3
# 2
0 3
0 3
1 4
2 4
3 5
4 5
# 3
0 3
1 4
2 5
3 6
4 6
6 7
# 4
1 5
2 6
3 7
5 8
7 9
9 10
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
++ = Use corresponding double sampling plan or multiple sampling plan for code letter D below.
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
++
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
++
++
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
++
++
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
++
++
1
4
8
12
17
21
25
2
7
13
19
25
31
37
7
10
13
17
20
23
26
9
14
19
25
29
33
38
++
++
2
7
13
19
25
31
37
4
11
19
27
36
45
53
9
14
19
25
29
33
38
12
19
27
34
40
47
54
++
++
4
11
19
27
36
45
53
6
17
29
40
53
65
77
12
19
27
34
40
47
54
16
27
39
49
58
68
78
++
++
6
17
29
40
53
65
77
16
27
39
49
58
68
78
++
++
##
##
##
Re = Rejection number.
Ac = Acceptance number.
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
++
++
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
= Use first sampling plan below arrow (refer to continuation of table on following page,
when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection.
Cumulative
sample size
Sample size
code letter
18
32
32
32
32
32
32
32
50
50
50
50
50
50
50
80
80
80
80
80
80
80
125
125
125
125
125
125
125
200
200
200
200
200
200
200
315
315
315
315
315
315
315
500
500
500
500
500
500
500
Sample
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
32
64
96
128
160
192
224
50
100
150
200
250
300
350
80
160
240
320
400
480
560
125
250
375
500
625
750
875
200
400
600
800
1000
1200
1400
315
630
945
1260
1575
1890
2205
500
1000
1500
2000
2500
3000
3500
Cumulative
sample size
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
1
1
2
2
2
2
3
3
3
3
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
# 2
# 2
0 2
0 3
1 3
1 3
2 3
# 2
0 3
0 3
1 4
2 4
3 5
4 5
# 2
0 3
1 4
2 5
3 6
4 6
6 7
# 4
1 5
2 6
3 7
5 8
7 9
9 10
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
Re = Rejection number.
Ac = Acceptance number.
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
0
3
6
8
11
14
18
1
4
8
12
17
21
25
2
7
13
19
25
31
37
5
8
10
13
15
17
19
7
10
13
17
20
23
26
9
14
19
25
29
33
38
1
4
8
12
17
21
25
2
7
13
19
25
31
37
7
10
13
17
20
23
26
9
14
19
25
29
33
38
2
7
13
19
25
31
37
9
14
19
25
29
33
38
= Use first sampling plan above arrow (refer to preceding page, when necessary).
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
7
10
13
17
20
23
26
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
8
10
13
15
17
19
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
1
4
8
12
17
21
25
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
(Continued)
Sample size
MULTIPLE
NORMAL
PLANS
19
A
B
C
Sample size
code letter
MULTIPLE
TIGHTENED
PLANS
2
4
6
8
10
12
14
3
6
9
12
15
18
21
5
10
15
20
25
30
35
8
16
24
32
40
48
56
13
26
39
52
65
78
91
20
40
60
80
100
120
140
Sample size
2
2
2
2
2
2
2
3
3
3
3
3
3
3
5
5
5
5
5
5
5
8
8
8
8
8
8
8
13
13
13
13
13
13
13
20
20
20
20
20
20
20
Sample
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
1
1
2
2
2
2
3
3
3
3
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
# 2
# 2
0 2
0 3
1 3
1 3
2 3
# 2
0 3
0 3
1 4
2 4
3 5
4 5
# 3
0 3
1 4
2 5
3 6
4 6
6 7
# 4
1 5
2 6
3 7
5 8
7 9
9 10
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
++ = Use corresponding double sampling plan or multiple sampling plan for code letter D below.
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
++
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
++
++
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
++
++
0
3
7
10
14
18
21
1
6
11
16
22
27
32
6
9
12
15
17
20
22
8
12
17
22
25
29
33
++
++
1
6
11
16
22
27
32
3
10
17
24
32
40
48
8
12
17
22
25
29
33
10
17
24
31
37
43
49
++
++
3
10
17
24
32
40
48
6
16
26
37
49
61
72
10
17
24
31
37
43
49
15
25
36
46
55
64
73
++
++
6
16
26
37
49
61
72
15
25
36
46
55
64
73
++
++
##
##
##
Re = Rejection number.
Ac = Acceptance number.
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
++
++
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
= Use first sampling plan below arrow (refer to continuation of table on following page,
when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection.
Cumulative
sample size
Sample size
code letter
20
32
64
96
128
160
192
224
50
100
150
200
250
300
350
80
160
240
320
400
480
560
125
250
375
500
625
750
875
200
400
600
800
1000
1200
1400
315
630
945
1260
1575
1890
2205
500
1000
1500
2000
2500
3000
3500
800
1600
2400
3200
4000
4800
5600
Sample size
32
32
32
32
32
32
32
50
50
50
50
50
50
50
80
80
80
80
80
80
80
125
125
125
125
125
125
125
200
200
200
200
200
200
200
315
315
315
315
315
315
315
500
500
500
500
500
500
500
800
800
800
800
800
800
800
Sample
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
1
1
2
2
2
2
3
3
3
3
#
#
0
0
1
1
2
2
2
2
3
3
3
3
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
2
2
2
3
3
3
3
2
3
3
4
4
5
5
2
3
4
5
6
6
7
# 2
# 2
0 2
0 3
1 3
1 3
2 3
# 2
0 3
0 3
1 4
2 4
3 5
4 5
# 2
0 3
1 4
2 5
3 6
4 6
6 7
# 4
1 5
2 6
3 7
5 8
7 9
9 10
2
2
2
3
3
3
3
2
3
3
4
4
5
5
2
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
= Use first sampling plan above arrow (refer to preceding page, when necessary).
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
2
3
3
4
4
5
5
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
3
3
4
5
6
6
7
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
4
5
6
7
8
9
10
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
4
7
9
11
12
14
15
6
9
12
15
17
20
22
8
12
17
22
25
29
33
0
3
7
10
14
18
21
1
6
11
16
22
27
32
6
9
12
15
17
20
22
8
12
17
22
25
29
33
1
6
11
16
22
27
32
8
12
17
22
25
29
33
Re = Rejection number.
Ac = Acceptance number.
#
1
2
3
5
7
9
0
2
4
6
9
12
14
0
3
7
10
14
18
21
1
6
11
16
22
27
32
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
(Continued)
Cumulative
sample size
MULTIPLE
TIGHTENED
PLANS
21
A
B
C
D
E
Sample
3
3
3
3
3
3
3
5
5
5
5
5
5
5
8
8
8
8
8
8
8
13
13
13
13
13
13
13
Sample size
3
6
9
12
15
18
21
5
10
15
20
25
30
35
8
16
24
32
40
48
56
13
26
39
52
65
78
91
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
0
0
1
2
2
2
3
3
3
3
#
#
0
0
0
0
1
#
#
0
0
0
1
1
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
0
0
1
#
#
0
0
0
1
1
#
#
0
0
1
1
2
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
#
#
0
0
0
0
1
#
#
0
0
0
1
1
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
3
4
5
6
7
7
8
# 2
# 2
0 2
0 3
0 3
0 3
1 3
# 2
# 3
0 3
0 4
0 4
1 5
1 5
# 3
# 3
0 4
0 5
1 6
1 6
2 7
# 3
0 4
0 5
1 6
2 7
3 7
4 8
# 4
0 5
1 6
2 7
3 8
4 9
6 10
++ = Use corresponding double sampling plan or multiple sampling plan for code letter F below.
++
++
=
=
=
=
=
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
3
4
5
6
7
7
8
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
7
9
12
13
15
17
6
9
12
15
17
20
22
++
++
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
7
9
12
13
15
17
6
9
12
15
17
20
22
++
++
0
3
6
8
11
14
18
#
1
2
3
5
7
9
0
1
3
5
7
10
13
6
9
12
15
17
20
22
4
6
8
10
11
12
14
5
7
9
12
13
15
17
++
++
0
1
3
5
7
10
13
0
3
6
8
11
14
18
++
++
5 0 6
7 3 9
9 6 12
12 8 15
13 11 17
15 14 20
17 18 22
6
9
12
15
17
20
22
++
++
##
##
##
##
##
##
##
Acceptance number.
Rejection number.
Acceptance not permitted at this sample size.
Use corresponding double sampling plan.
If, after the final sample, the acceptance number has been exceeded,
but the rejection number has not been reached, accept the lot but
reinstate normal inspection (see 10.1.4).
2 # 3
3 # 3
3 0 4
4 0 5
4 1 6
5 1 6
5 2 7
3 # 3
3 0 4
4 0 5
5 1 6
6 2 7
6 3 7
7 4 8
3 # 4
4 0 5
5 1 6
6 2 7
7 3 8
7 4 9
8 6 10
4 # 4
5 1 6
6 2 8
7 3 10
8 5 11
9 7 12
10 9 14
4 0 5
6 1 7
8 3 9
10 5 12
11 7 13
12 10 15
14 13 17
Ac
Re
#
##
#
#
0
0
0
1
1
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
++
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
= Use first sampling plan below arrow (refer to continuation of table on following page,
when necessary). If sample size equals or exceeds lot or batch size, do 100 percent inspection.
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
Cumulative
sample size
Sample size
code letter
MULTIPLE
REDUCED
PLANS
Sample size
code letter
22
20
20
20
20
20
20
20
32
32
32
32
32
32
32
50
50
50
50
50
50
50
80
80
80
80
80
80
80
125
125
125
125
125
125
125
200
200
200
200
200
200
200
Sample
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
First
Second
Third
Fourth
Fifth
Sixth
Seventh
50
100
150
200
250
300
350
80
160
240
320
400
480
560
125
250
375
500
625
750
875
200
400
600
800
1000
1200
1400
32
64
96
128
160
192
224
20
40
60
80
100
120
140
Cumulative
sample size
0.15
0.25
0.40
0.65
1.0
1.5
2.5
4.0
6.5
10
15
25
40
65
100
150
250
400
650
1000
#
#
0
0
0
0
1
2
2
2
3
3
3
3
#
#
0
0
0
0
1
#
#
0
0
0
1
1
2
2
2
3
3
3
3
2
3
3
4
4
5
5
#
#
0
0
0
0
1
#
#
0
0
0
1
1
#
#
0
0
1
1
2
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
#
#
0
0
0
0
1
#
#
0
0
0
1
1
#
#
0
0
1
1
2
#
0
0
1
2
3
4
2
2
2
3
3
3
3
2
3
3
4
4
5
5
3
3
4
5
6
6
7
3
4
5
6
7
7
8
# 2
# 2
0 2
0 3
0 3
0 3
1 3
# 2
# 3
0 3
0 4
0 4
1 5
1 5
# 3
# 3
0 4
0 5
1 6
1 6
2 7
# 3
0 4
0 5
1 6
2 7
3 7
4 8
# 4
0 5
1 6
2 7
3 8
4 9
6 10
#
#
0
0
0
1
1
#
#
0
0
1
1
2
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
#
#
0
0
0
0
1
2
3
3
4
4
5
5
#
0
0
1
2
3
4
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
#
#
0
0
1
1
2
3
4
5
6
7
7
8
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
7
9
12
13
15
17
6
9
12
15
17
20
22
3
3
4
5
6
6
7
#
0
1
2
3
4
6
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
#
0
0
1
2
3
4
4
5
6
7
8
9
10
4
6
8
10
11
12
14
5
7
9
12
13
15
17
6
9
12
15
17
20
22
3
4
5
6
7
7
8
#
1
2
3
5
7
9
0
1
3
5
7
10
13
0
3
6
8
11
14
18
4
6
8
10
11
12
14
5
7
9
12
13
15
17
6
9
12
15
17
20
22
# 4
0 5
1 6
2 7
3 8
4 9
6 10
0
1
3
5
7
10
13
0
3
6
8
11
14
18
#
1
2
3
5
7
9
Re = Rejection number.
Ac = Acceptance number.
5 0 6
7 3 9
9 6 12
12 8 15
13 11 17
15 14 20
17 18 22
6
9
12
15
17
20
22
4 0 5 0 6
6 1 7 3 9
8 3 9 6 12
10 5 12 8 15
11 7 13 11 17
12 10 15 14 20
14 13 17 18 22
= If, after the final sample, the acceptance number has been exceeded, but the rejection number has not been reached, accept the lot, but reinstate normal inspection (see 10.1.4).
#
#
0
0
0
1
1
2 # 3
3 # 3
3 0 4
4 0 5
4 1 6
5 1 6
5 2 7
3 # 3
3 0 4
4 0 5
5 1 6
6 2 7
6 3 7
7 4 8
3 # 4
4 0 5
5 1 6
6 2 7
7 3 8
7 4 9
8 6 10
4 # 4
5 1 6
6 2 8
7 3 10
8 5 11
9 7 12
10 9 14
4 0 5
6 1 7
8 3 9
10 5 12
11 7 13
12 10 15
14 13 17
2
2
2
3
3
3
3
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
(Continued)
Sample size
MULTIPLE
REDUCED
PLANS
AOQL
NORMAL
PLANS
23
32
50
80
125
200
315
500
2000
20
13
800
1250
Sample
size
Code
Letter
0.046
250
170
110
4.7
3.0
2.9
2.1
1.9
1.8
1.4
1.3
1.2
1.2
1.00
0.90
0.82
0.75
0.73
0.44 0.62
0.39 0.63
0.40 0.56
0.36 0.52
0.33 0.47
0.27
0.27
0.24
0.25
0.22
0.17
0.17
0.16
0.067 0.11
(See 11.4)
7.3
4.7
3.3
2.2
1.6
0.97
Sample size
Lot or Batch size
12
7.5
5.2
3.6
2.5
1.6
1.1
0.67
0.42 0.69
18
12
8.2
5.6
4.0
2.4
1.7
1.1
0.11
29
19
46
29
21
73
47
33
22
16
9.7
13
72
50
34
24
15
11
6.9
14
Note: For a more accurate AOQL, the above values must be multiplied by
0.029
410
270
180
120
82
56
40
24
17
11
9.0
0.074
660
430
290
190
130
90
63
39
27
17
9.9
0.12
720 1100
490
310
220
150
6.3
0.29
730 1100
470
330
220
160
97
110
63
18
69
650 1000
400
250
150
100
65
40
25
46
15
42
10
(See 11.4)
28
6.5
6.5
12
4.0
4.2
7.4
2.5
6.1
4.6
1.5
3.9
2.8
1.0
4.3
1.2
1.8
0.65
2.7
0.74
0.25 0.40
2.6
0.46
0.15
1.7
0.18
AOQL
TIGHTENED
PLANS
24
2000
3150
500
800
315
1250
200
125
80
20
13
50
32
Sample
size
Code
Letter
0.027
0.046
0.11
0.16
0.17
0.067 0.11
0.17
0.29
0.15
610
390
380
250
240
240
160
160
150
100
99
95
63
64
61
62
39
40
40
40
27
24
24
26
17
17
15
16
11
11
9.7
6.5
6.9
2.5
1.6
1.6
1.0
0.99
0.99
0.63
0.64
0.64
0.62
0.27 0.39
0.24 0.40
0.25 0.41
0.26 0.40
Sample size
Lot or Batch size
3.9
2.5
1.6
1.0
0.62
0.27 0.44
6.2
4.0
2.6
1.6
(See 11.4)
9.9
6.4
4.1
2.5
1.6
0.97
16
9.9
6.4
4.0
2.4
1.7
1.1
1.1
25
16
6.3
0.69
25
16
9.9
10
6.1
3.9
39
650 1100
410
270
170
970
620
400
260
160
97
110
12
65
650 1000
400
250
150
100
65
40
69
25
46
15
42
10
(See 11.4)
28
6.5
4.3
4.2
7.4
4.0
2.7
4.6
2.5
2.6
2.8
1.5
1.7
1.8
1.0
0.67
1.2
0.65
0.42
0.46
0.74
0.25 0.40
Note: For a more accurate AOQL, the above values must be multiplied by
0.018
0.029
0.074
0.12
0.18
LQ (Nonconforming Units)
10% PLANS
25
L
M
N
2000
125
80
1250
50
32
800
20
8
13
Sample
size
Code
Letter
0.18
0.29
0.20
0.46
0.27
0.31
0.73
0.33
0.43
0.49
1.2
2.3
1.6
1.4
1.2
1.0
0.94
0.77
0.74
0.59
0.53
0.46
5.6
3.5
4.0
2.5
3.1
1.9
2.4
1.5
1.9
1.3
1.1
1.2
9.0
6.4
4.9
3.7
2.9
2.1
1.7
1.2
0.84
14
10
7.7
5.9
23
16
12
9.4
7.4
14
11
8.2
6.5
4.8
4.6
24
19
18
13
10
7.6
5.4
29
22
3.3
34
27
20
16
12
4.3
42
2.7
44
30
58
10
25
68
6.5
18
54
4.0
54
37
2.5
36
25
1.5
41
16
1.0
27
11
0.65
3.1
4.5
6.9
0.25 0.40
2.0
2.8
0.15
0.67
0.78
1.8
(See 11.6)
LQ (Nonconformities)
10% PLANS
26
13
20
32
50
80
125
200
315
500
800
1250
2000
Sample
size
Code
Letter
0.18
0.29
0.20
0.46
0.27
0.31
0.73
0.33
0.43
0.49
1.2
14
10
9.0
7.7
6.4
5.6
5.9
4.9
4.0
3.5
4.6
3.7
3.1
2.5
2.3
3.3
2.9
2.4
1.9
1.6
1.4
2.1
1.9
1.5
1.2
1.0
1.7
1.3
1.2
0.94
0.77
1.2
1.1
0.84
0.74
0.59
0.78
0.67
0.53
0.46
23
16
12
9.4
7.4
5.4
4.3
15
12
35
25
19
19
13
56
40
31
24
8.4
88
63
48
37
29
21
17
12
11
140
100
77
59
46
33
27
20
6.7
410
300
220
160
120
91
670
480
350
250
190
150
120
71
770 1100
560
400
310
240
190
130
110
78
84
51
650 1000
180
400
250
150
100
65
40
25
200
15
(See 11.6)
130
10
67
120
6.5
41
77
4.0
49
46
2.5
30
29
1.5
7.8
18
1.0
4.9
12
0.65
2.7
4.6
7.2
0.25 0.40
3.1
2.9
0.15
2.0
1.8
Table VI-BLimiting Quality (in nonconformities per hundred units) for Which Pa = 10 Percent
(for Normal Inspection, Single Sampling)
LQ (Nonconforming Units)
5% PLANS
27
L
M
N
2000
125
80
1250
50
32
800
20
8
13
Sample
size
Code
Letter
0.24
0.38
0.24
0.60
0.32
0.38
0.95
0.39
0.50
0.59
1.5
2.4
1.8
1.5
1.4
1.1
1.1
0.85
0.84
0.66
0.62
0.53
6.1
3.8
4.4
2.7
3.4
2.1
2.6
1.6
2.1
1.6
1.3
1.3
9.6
7.0
5.4
4.2
3.3
2.5
2.0
1.5
0.97
15
11
8.5
6.6
24
18
14
11
8.4
16
13
9.4
7.7
5.8
5.3
26
20
20
15
12
9.1
6.2
32
25
3.9
37
30
23
18
14
5.0
46
3.2
50
34
66
10
28
78
6.5
22
63
4.0
60
45
2.5
41
31
1.5
47
21
1.0
32
14
0.65
3.8
5.8
8.9
0.25 0.40
2.4
3.7
0.15
0.79
0.95
2.4
(See 11.6)
LQ (Nonconformities)
5% PLANS
28
13
20
32
50
80
125
200
315
500
800
1250
2000
Sample
size
Code
Letter
0.24
0.38
0.24
0.60
0.32
0.38
0.95
0.39
0.50
0.59
1.5
15
11
9.6
8.5
7.0
6.1
6.6
5.4
4.4
3.8
5.3
4.2
3.4
2.7
2.4
3.3
2.6
2.1
1.8
1.5
2.5
2.1
1.6
1.4
1.1
2.0
1.6
1.3
1.1
0.85
1.5
1.3
0.97
0.84
0.66
0.95
0.79
0.62
0.53
24
18
14
11
8.4
6.2
5.0
3.9
16
13
38
27
21
21
16
61
44
34
26
9.7
95
68
53
41
33
24
20
15
13
150
110
85
66
53
39
32
24
7.9
440
310
230
170
130
100
670
510
380
270
210
160
130
81
810 1100
610
440
340
260
210
160
130
95
97
60
650 1000
210
400
250
150
100
65
40
25
240
15
(See 11.6)
160
10
79
150
6.5
59
100
4.0
48
60
2.5
37
38
1.5
9.5
23
1.0
5.9
15
0.65
3.2
6.0
9.4
0.25 0.40
3.8
3.8
0.15
2.4
2.4
Table VII-BLimiting Quality (in nonconformities per hundred units) for Which Pa = 5 Percent
(for Normal Inspection, Single Sampling)
LIMIT
NUMBERS
29
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
12501999
50007999
1250019999
2000031499
24
40
67
22
38
14
24
8
14
4
8
2
4
111
68
40
24
14
*
*
*
*
*
*
186
115
69
42
25
14
*
*
*
*
*
*
0.65
181
110
68
40
24
14
169
105
63
38
22
181
110
67
40
24
181
111
68
49
186
115
69
181
110
169
181
105
68
42
24
14
4
13
181
63
40
25
113
68
110
39
24
14
8
14
189
471
277
181
115
68
40
22
14
490
301
177
72
42
25
297
181
105
68
115
42
24
14
7
13
301
181
63
40
25
277
178
105
63
110
36
22
13
7
14
181
115
650 1000
68
400
40
250
22
150
14
100
65
40
25
15
10
6.5
*
*
4.0
*
*
*
2.5
*
*
*
1.5
*
*
*
*
*
1.0
may be used for the calculation, provided that the lots or batches used are the most recent ones in sequence, that they have all been on normal inspection, and that none has
been rejected while on original inspection.
14
7
13
0
0
*
*
*
*
*
*
*
*
0.25 0.40
*
*
*
*
*
*
*
*
*
0.15
(See 4.7.3)
* = Denotes that the number of sample units from the last ten lots or batches is not sufficient for reduced inspection for this AQL. Is this instance, more than ten lots or batches
800012499
31504999
20003149
8001249
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
500799
320499
200319
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
130199
80129
5079
3049
*
*
*
*
*
*
*
*
*
*
*
*
2029
*
*
*
*
*
*
Number of
sample units
from last 10
lots or batches
10
15
le
ul
tip
AVERAGE
SAMPLE SIZE
PLANS
30
18
i pl
uble
c = 10
ul t
Do
c=2
Doub
le
12
c = 27
27
16
36
M
ul
ti
e
c=3
pl
12
15
18
10
20
tip
le
30
40
n proportion nonconforming
ul
le
c = 30
Dou
b
n proportion nonconforming
le
c = 12
Mu
lti
p
Doub
le
n proportion nonconforming
l tipl
le
tip
25
c = 21
14
Mu
ul
20
le
c=8
ti p
ble
Do
ub
M
ul
Do
u
13
10
27
15
Dou
b
le
12
pl
18
39
52
c = 41
36
Double
Double
20
45
c = 44
54
25
c = 18
le
c = 14
0
ti p
c=7
M
ul
Dou
ble
pl
e
Mu
l ti
Dou
ble
10
12 15 18 21
26
c=5
Dou
ble
M
ul t
i pl
e
c=1
ipl
Do
ub
le
ul t
u lt
Do
ubl
e
l ti p
1/4 n
Doub
le
(See 11.5)
Mu
1/2 n
3/4 n
1/4 n
1/2 n
3/4 n
1/4 n
1/2 n
3/4 n
Table IXAverage sample size curves for double and multiple sampling plans
(normal and tightened inspection)
le
tip
ul
31
PLANS
200
40
300
65
400
100
500
150
600
700
250
800
900
400
1000
1100
1200
1300
650
1400
1500
1600
1700
1800
1000
1900
6.5
150
230
5.13
13.4
29.3
50.0
68.4
77.6
90.0
90.0
75.0
50.0
25.0
10.0
5.0
1.0
40
332
237
194
135
83.9
48.1
26.6
17.8
7.43
25
65
420
315
266
196
134
86.4
55.1
40.9
21.8
40
150
655
526
464
371
284
211
158
131
89.3
100
250
800
657
589
484
383
298
233
199
145
250
870
722
650
540
433
342
272
235
175
1007
848
770
651
533
431
351
308
239
400
1141
972
889
761
633
521
432
384
305
150
100
502
388
334
255
184
127
87.2
68.3
41.2
65
1272
1094
1006
870
733
612
515
462
374
400
650
1529
1335
1238
1087
933
795
684
622
517
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
115
69.3
34.7
14.4
5.27
2.56
2.53
95.0
6.5
0.503
p (in percent
nonconforming)
1718
1512
1409
1248
1083
934
812
745
629
625
TABLE X-A-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
1000
2088
1862
1748
1568
1383
1214
1073
995
859
2270
2035
1916
1728
1533
1354
1206
1122
977
1000
2000
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
100
25
0.501
6.5
INDIVIDUAL PLANS
CHART AOPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
(Curves for double and multiple sampling are matched as closely as practicable)
99.0
Pa
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
PLANS
32
Multiple
Double
Single
Type of
sampling
plan
X
10
15
25
40
65
100
150
X
250
X
400
10
Use
Code
Letter
D
15
Use
Code
Letter
C
25
Use
Code
Letter
B
65
(*)
100
(*)
150
(*)
(*)
250
(*)
650
1000
(*)
400
(*)
(*)
Use single sampling plan (or alternatively use code letter B).
Use single sampling plan above (or alternatively use code letter D).
Re = Rejection number.
Ac = Acceptance number.
650
(*)
(*)
1000
(*)
(*)
10 11 12 13 14 15 18 19 21 22 27 28 30 31
40
(*)
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
Less than
10
* =
(*) =
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
6.5
Ac Re
Cumulative
sample
size
33
PLANS
100
15 25
200
40
65
300
100
400
150
500
600
250
700
800
400
900
1000
1100
1200
650
1300
1400
1500
1600
INDIVIDUAL PLANS
1700
1000
1800
1900
2000
4.0
53.6
63.2
78.5
10.0
5.0
1.0
6.5
99.9
154
37.0
25.0
9.59
6.5
76.8
46.2
23.1
9.14
3.51
1.71
20.6
3.45
90.0
50.0
1.70
95.0
0.335
75.0
0.33
4.0
40
280
210
177
131
89.1
57.6
36.7
27.3
14.5
25
65
335
258
223
170
122
84.5
58.2
45.5
27.4
40
150
580
150
481
433
360
289
228
181
157
117
533
438
392
323
256
199
155
133
96.9
671
565
514
434
356
287
234
206
159
250
761
648
593
507
422
347
288
256
203
100
848
730
671
580
489
408
343
308
249
250
100
437
350
309
247
189
141
105
87.1
59.5
65
400
1019
890
825
724
622
530
456
415
345
1145
1008
939
832
722
623
541
495
419
400
650
1392
1241
1165
1045
922
809
716
663
572
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
25
221
158
130
89.8
55.9
32.0
17.7
11.8
4.95
15
1513
1356
1277
1152
1022
903
804
748
651
650
TABLE X-B-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
1000
1951
1773
1683
1539
1389
1249
1131
1065
947
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
4.0
p (in percent
nonconforming)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
99.0
Pa
2069
1886
1793
1644
1489
1344
1222
1152
1029
1000
PLANS
Multiple
Double
Single
Type of
sampling
plan
34
X
10
15
25
40
65
100
X
150
X
250
Use
Code
Letter
A
10
Use
Code
Letter
D
15
Use
Code
Letter
C
X
400
650
1000
3 4
0 3
2 3
4 5
1 4
3 4
6 7
2 5
5 6
8 9
3 7
7 8
5 9
6 10
7 11
25
65
100
150
250
40
Use double sampling plan above (or alternatively use code letter D).
Use single sampling plan above (or alternatively use code letter E).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16 15 20 17 22 23 29 25 31
10 11 12 13 14 15 18 19 21 22 27 28 30 31 41 42 44 45
11 12 12 13 15 16 18 19 23 24 26 27 34 35 37 38 52 53 56 57
3 7
8 9
400
650
1000
++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++
1 2
0 2
1 2
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
6.5
Less than
6.5
6.5
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
4.0
* =
+ +=
Ac Re
Cumulative
sample
size
35
PLANS
10
100
2.5 10 15 25
40
200
65
300
100
150
400
500
250
600
700
400
800
900
1000
650
1100
1200
7.64
4.0
4.0
25
168
126
40
201
155
134
102
73.4
50.7
34.9
27.3
16.5
25
100
320
263
235
194
153
119
93.1
79.6
58.1
100
348
289
260
216
173
137
109
93.9
70.1
403
339
308
260
213
172
140
123
95.4
150
456
389
356
304
253
208
173
154
122
65
509
438
403
348
293
245
206
185
150
150
65
262
210
185
148
113
84.4
63.0
52.3
37.5
40
250
612
534
495
435
373
318
273
249
207
687
605
564
499
433
374
325
298
251
250
400
835
745
699
627
553
485
429
398
343
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
15
133
94.9
59.9
92.1
77.8
60.2
65.7
45.1
5.0
77.8
46.1
1.0
78.4
106
53.9
27.7
58.4
36.9
10.0
45.4
24.2
25.0
34.5
53.5
5.75
33.6
19.4
5.59
19.2
22.0
16.4
10.6
7.11
8.72
15
13.9
2.11
1.03
2.97
10
31.4
11.2
12.9
2.09
90.0
0.201
2.5
50.0
1.02
95.0
3.27
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
908
814
766
691
613
542
482
449
391
400
TABLE X-C-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
75.0
0.201
p (in percent
nonconforming)
2.5
10
20
30
40
50
60
70
80
90
100
INDIVIDUAL PLANS
650
1171
1064
1010
923
833
749
679
639
568
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
99.0
Pa
1241
1131
1076
986
893
806
733
691
618
650
PLANS
Multiple
Double
Single
Type of
sampling
plan
36
X
6.5
10
15
25
40
65
X
100
X
150
Use
Code
Letter
B
6.5
Use
Code
Letter
E
10
Use
Code
Letter
D
X
250
X
400
650
3 4
0 3
2 3
4 5
1 4
3 4
6 7
2 5
5 6
8 9
3 7
7 8
1000
5 9
6 10
7 11
15
25
65
100
150
40
Use double sampling plan above (or alternatively use code letter D).
Use single sampling plan above (or alternatively use code letter F).
Re = Rejection number.
Ac = Acceptance number.
9 14
250
400
650
1000
Use
Code
Letter
11 16 15 20 17 22 23 29 25 31
B
10 11 12 13 14 15 18 19 21 22 27 28 30 31 41 42 44 45
11 12 12 13 15 16 18 19 23 24 26 27 34 35 37 38 52 53 56 57
3 7
8 9
++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++
1 2
0 2
1 2
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
4.0
Less than
4.0
4.0
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
2.5
* =
+ +=
Ac Re
Cumulative
sample
size
37
PLANS
50
15
100
25
40
150
65
200
100
250
300
150
350
400
450
250
500
550
INDIVIDUAL PLANS
600
400
650
700
1.97
4.64
0.126
.0639
99.0
95.0
30.3
40.6
47.1
59.0
10
15.9
25.0
31.2
43.8
2.5
5.0
1.0
8.30
50.0
10.0
12.1
20.1
3.53
75.0
25.0
6.88
1.32
90.0
37.4
2.5
15
105
78.7
66.5
49.0
33.4
21.6
13.8
10.2
5.45
10
25
126
96.9
83.5
63.9
45.9
31.7
21.8
17.1
10.3
15
200
164
147
121
95.9
74.5
58.2
49.8
36.3
40
65
100
65
218
180
162
135
108
85.5
67.9
58.7
43.8
252
212
193
163
133
108
87.8
77.1
59.6
100
285
243
222
190
158
130
108
96.1
76.2
318
274
252
217
183
153
129
116
93.5
40
164
131
116
92.8
70.9
52.7
39.4
32.7
22.3
25
150
382
334
309
272
233
199
171
156
129
429
378
352
312
271
234
203
186
157
150
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
10
83.0
59.3
48.6
28.8
53.8
57.6
33.7
17.3
43.3
70.7
21.0
32.1
60.0
12.0
3.60
8.66
22.1
4.44
6.65
0.641
1.31
11.1
1.86
6.5
0.126
1.5
6.08
10
14.7
p (in percent
nonconforming)
250
522
465
437
392
346
303
268
249
215
TABLE X-D-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
568
509
479
432
383
339
301
281
244
250
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
6.5
1.5 6.5 10
1.5
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
Pa
400
732
665
631
577
521
468
424
399
355
776
707
672
617
558
504
458
432
386
450
PLANS
Multiple
Double
Single
Type of
sampling
plan
38
4.0
6.5
X
4.0
Use
Code
Letter
F
6.5
Use
Code
Letter
E
# 2
1 2
0 2
1 2
1 3
1 3
2 3
10
12
14
10
15
25
40
X
65
X
100
15
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
40
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
= Use single sampling plan above (or alternatively use code letter G).
Re = Rejection number.
Ac = Acceptance number.
*
#
X
150
X
250
400
5 9
6 10
7 11
9 14
11 16 15 20 17 22 23 29 25 31
10 11 12 13 14 15 18 19 21 22 27 28 30 31 41 42 44 45
9 12
6 11
4 9
2 7
0 4
8 13
4 10
7 14
2 9
4 12
6 15
6 16
10 17 11 19 16 25 17 26
3 10
11 17 13 19 17 24 19 27 26 36 29 39
6 12
10 15 12 17 16 22 19 25 24 31 27 34 37 46 40 49
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29 32 37 36 40 49 55 53 58
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27 34 35 37 38 52 53 56 57
3 7
8 9
65
100
150
250
400
13 14 14 15 18 19 21 22 25 26 32 33 37 38 48 49 53 54 72 73 77 78
10 12 12 14 14 17 18 20 21 23 27 29 31 33 40 43 45 47 61 64 65 68
7 11
5 10
0 4
8 9
3 7
7 8
25
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
10
0 3
2.5
Use
Code
Letter
C
0 2
Less than
2.5
# 2
2.5
Higher
than
400
14
12
10
10
size
Cumu-
Higher lative
than
sample
400
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
1.5
10
Ac Re
39
PLANS
50
15
75
25
100
40
125
65
150
175
200
100
225
250
275
150
300
325
350
375
250
INDIVIDUAL PLANS
400
425
450
475
1.18
2.81
4.17
7.41
0.077
0.394
0.807
2.19
5.19
99.0
95.0
90.0
75.0
50.0
6.5
19.4
26.8
31.6
41.3
6.5
10.1
16.2
20.6
29.8
1.5
25.0
10.0
5.0
1.0
12.6
10
50.6
41.0
36.0
28.0
20.0
13.4
8.80
6.60
3.58
p (in percent
nonconforming)
4.0
6.5
51.1
10
64.7
48.4
40.9
30.2
20.6
13.3
8.48
6.29
3.35
6.5
25
101
80.9
71.3
57.1
43.6
32.5
24.2
20.1
13.7
15
40
65
123
101
90.5
74.5
59.0
45.8
35.8
30.6
22.4
40
134
111
100
83.1
66.7
52.6
41.8
36.1
27.0
155
130
119
100
82.1
66.3
54.0
47.5
36.7
65
176
150
137
117
97.4
80.2
66.5
59.2
46.9
264
235
196
100
233
205
168
134
217
167
144
192
187
144
122
190
165
125
167
153
115
95.7
105
150
321
286
269
241
213
132
X
96.7
100
79.6
155
113
94.1
79.2
71.1
57.5
25
15
77.3
59.6
51.4
39.3
28.2
19.5
13.4
10.5
6.33
10
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
1.5
23.0
49.5
36.5
29.9
17.7
44.4
35.4
20.7
10.7
36.1
58.8
7.39
12.9
2.21
5.33
0.810
27.5
2.73
4.09
0.395
11.3
14.2
19.9
1.15
4.0
0.077
1.0
6.95
10
TABLE X-E-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
349
313
295
266
236
208
185
173
150
150
250
450
409
388
355
321
288
261
246
219
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
25
1.0
Pa
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
477
435
414
379
344
310
282
266
238
150
PLANS
Multiple
Double
Single
Type of
sampling
plan
40
2.5
4.0
X
2.5
Use
Code
Letter
G
4.0
Use
Code
Letter
F
# 2
1 2
0 2
1 2
1 3
1 3
2 3
15
18
21
6.5
10
15
25
X
40
X
65
10
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
25
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
= Use single sampling plan above (or alternatively use code letter H).
Re = Rejection number.
Ac = Acceptance number.
*
#
X
100
X
150
250
5 9
6 10
7 11
9 14
11 16 15 20 17 22 23 29 25 31
10 11 12 13 14 15 18 19 21 22 27 28 30 31 41 42 44 45
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
4 12
6 15
6 16
10 17 11 19 16 25 17 27
3 10
11 17 13 19 17 24 19 27 26 36 29 39
6 12
10 15 12 17 16 22 19 25 24 31 27 34 37 46 40 49
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29 32 37 36 40 49 55 53 58
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27 34 35 37 38 52 53 56 57
3 7
8 9
40
65
100
150
250
13 14 14 15 18 19 21 22 25 26 32 33 37 38 48 49 53 54 72 73 77 78
10 12 12 14 14 17 18 20 21 23 27 29 31 33 40 43 45 47 61 64 65 68
7 11
5 10
0 4
8 9
3 7
7 8
15
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
6.5
0 3
12
1.5
Use
Code
Letter
D
0 2
Less than
1.5
# 2
1.5
Higher
than
250
21
18
15
12
13
13
size
Cumu-
Higher lative
than
sample
250
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
1.0
13
13
Ac Re
41
PLANS
10
0.65
2.5
20
4.0
6.5
30
10
40
50
15
60
25
70
80
90
40
100
110
120
65
INDIVIDUAL PLANS
130
140
150
28.3
35.8
6.5
28.9
4.0
1.0
24.5
18.7
21.6
18.1
12.9
8.70
13.1
20.6
6.70
25.0
8.25
4.81
13.9
3.41
50.0
5.64
4.22
1.0
1.43
75.0
2.69
1.80
2.27
5.0
0.525
90.0
0.759
10.9
0.256
95.0
4.0
p (in percent
nonconforming)
10.0
0.0502
99.0
2.5
23.0
1.0
15.0
11.5
6.93
3.47
1.44
0.527
0.256
0.0503
0.65
53.2
45.6
41.5
34.8
27.9
21.6
16.6
14.0
9.75
10
6.5
42.0
31.5
26.6
19.6
13.4
8.65
5.51
4.09
2.18
4.0
10
50.2
38.8
33.4
25.5
18.4
12.7
8.72
6.83
4.12
6.5
15
25
15
65.5
52.6
46.4
37.1
28.4
21.1
15.8
13.1
8.93
80.0
65.7
58.9
48.4
38.3
29.8
23.3
19.9
14.5
25
87.0
72.2
65.0
54.0
43.3
34.2
27.2
23.5
17.5
101
84.8
77.0
65.1
53.3
43.1
35.1
30.8
23.9
10
4.0
33.2
23.7
19.4
13.5
8.39
4.81
2.66
1.78
0.743
2.5
40
114
97.2
88.9
76.1
63.3
52.1
43.2
38.4
30.5
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
10
42.1
34.4
30.4
24.2
18.1
12.8
9.03
7.14
4.36
6.5
127
109
101
87.0
73.3
61.2
51.5
46.2
37.4
40
TABLE X-F-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
65
153
133
124
109
93.3
79.5
68.4
62.2
51.7
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
0.65
Pa
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
93.4
81.2
74.5
62.9
65
172
151
141
125
108
160
PLANS
42
Multiple
Double
Single
Type of
sampling
plan
1.5
2.5
X
1.5
Use
Code
Letter
H
2.5
Use
Code
Letter
G
# 2
1 2
0 2
1 2
1 3
1 3
2 3
25
30
35
4.0
6.5
10
15
X
25
6.5
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
10
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
15
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
40
65
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter H).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
25
40
65
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
4.0
0 3
20
1.0
Use
Code
Letter
E
0 2
15
Less than
1.0
# 2
1.0
Higher
than
65
35
30
25
20
15
10
26
13
20
size
Cumu-
Higher lative
than
sample
65
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.65
10
26
13
20
Ac Re
43
PLANS
2.14
50.0
1.0
0.65
13.4
8.94
0.895
75.0
5.0
0.329
90.0
4.24
0.160
95.0
6.94
0.0314
99.0
10.0
0.40
Pa
25.0
0.40
10
1.5
2.5
4.0
20
6.5
30
10
40
15
50
25
60
70
80
40
90
INDIVIDUAL PLANS
100
4.0
6.5
23.8
4.0
2.5
10
36.0
30.1
27.1
22.3
17.5
13.4
10.2
8.50
5.88
6.5
0.65
2.5
20.7
14.8
12.2
8.41
5.24
3.00
1.66
1.11
0.464
1.5
4.0
26.3
19.7
16.6
12.3
8.36
5.40
3.44
2.56
1.36
2.5
6.5
31.4
24.2
20.9
16.0
11.5
7.92
5.45
4.26
2.57
4.0
10
15
10
41.0
32.9
29.0
23.2
17.7
13.2
9.85
8.17
5.58
50.0
41.1
36.8
30.3
24.0
18.6
14.6
12.4
9.08
15
54.4
45.1
40.6
33.8
27.1
21.4
17.0
14.7
11.0
63.0
53.0
48.1
40.7
33.3
26.9
21.9
19.3
14.9
6.5
14.4
9.36
7.20
4.33
2.17
0.899
0.329
0.160
0.0314
0.40
43.2
37.2
34.1
29.0
23.7
19.0
15.1
13.1
9.73
10
25
71.3
60.8
55.6
47.6
39.6
32.6
27.0
24.0
19.1
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
28.1
18.4
22.5
19.7
15.4
11.4
7.98
5.56
4.38
2.67
19.0
15.8
11.9
8.27
5.42
3.49
2.60
1.40
p (in percent
nonconforming)
2.5
14.0
11.6
8.19
5.19
3.01
1.67
1.12
0.471
1.5
79.5
68.4
62.9
54.4
45.8
38.2
32.2
28.9
23.4
25
TABLE X-G-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
40
95.6
83.4
77.4
67.9
58.3
49.7
42.7
38.9
32.3
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
107
94.5
88.1
78.0
67.7
58.4
50.8
46.5
39.3
40
PLANS
44
Multiple
Double
Single
Type of
sampling
plan
1.0
1.5
X
1.0
Use
Code
Letter
J
1.5
Use
Code
Letter
H
# 2
1 2
0 2
1 2
1 3
1 3
2 3
40
48
56
2.5
4.0
6.5
10
X
15
4.0
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
6.5
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
10
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
25
40
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter K).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
15
25
40
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
2.5
0 3
32
0.65
Use
Code
Letter
F
0 2
24
Less than
0.65
# 2
0.65
Higher
than
40
56
48
40
32
24
16
40
20
32
size
Cumu-
Higher lative
than
sample
40
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.40
16
40
20
32
Ac Re
45
PLANS
0.25
1.0
1.5
10
2.5
15
4.0
20
6.5
25
10
30
35
15
40
45
50
25
55
INDIVIDUAL PLANS
60
65
12.6
1.5
0.103
0.211
0.574
1.38
2.73
4.50
5.82
8.80
0.40
95.0
90.0
75.0
50.0
25.0
10.0
5.0
1.0
9.14
7.56
5.29
33.3
1.92
1.07
0.715
0.300
0.0201
99.0
1.0
0.25
Pa
2.5
15.8
12.1
10.3
7.69
5.31
3.46
2.22
1.66
0.886
1.5
4.0
8.22
9.54
5.36
6.43
8.51
2.78
3.53
5.10
31.7
10
29.2
27.0
24.7
21.0
17.2
13.8
11.2
9.72
7.36
5.99
0.40
1.5
13.3
9.49
7.78
5.39
3.36
1.92
1.06
0.711
0.297
1.0
2.5
16.8
12.6
10.6
7.84
5.35
3.45
2.20
1.64
0.872
1.5
4.0
6.5
10
4.0
20.1
15.5
13.4
10.2
7.34
5.07
3.49
2.73
1.65
6.5
26.2
21.0
18.5
14.8
11.3
8.44
6.30
5.23
3.57
25.3
21.3
26.0
30.8
33.9
40.3
17.3
21.6
26.0
28.9
34.8
19.4
23.5
26.3
34.8
20.8
17.2
13.7
15.3
11.9
10
17.3
14.0
15
45.6
38.9
35.6
30.4
15.4
12.3
9.39
10.9
7.96
9.31
7.01
12.2
X
5.81
9.54
2.5
9.21
31.6
36.3
4.61
2.77
1.39
0.575
0.210
0.103
0.0201
0.25
29.1
25.2
21.2
17.5
14.5
12.9
10.1
10
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
6.5
4.0
19.9
14.8
24.7
22.4
17.8
12.9
24.2
18.8
14.5
10.0
18.7
15.2
11.3
7.29
12.0
6.07
3.69
6.5
1.68
p (in percent
nonconforming)
2.5
TABLE X-H-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
50.9
43.8
40.3
34.8
29.3
24.5
20.6
18.5
15.0
15
25
61.1
53.4
49.5
43.5
37.3
31.8
27.3
24.9
20.7
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
68.7
60.5
56.4
49.9
43.3
37.4
32.5
29.8
25.1
25
PLANS
46
Multiple
Double
Single
Type of
sampling
plan
0.65
1.0
X
0.65
Use
Code
Letter
K
1.0
Use
Code
Letter
J
# 2
1 2
0 2
1 2
1 3
1 3
2 3
65
78
91
1.5
2.5
4.0
6.5
X
10
2.5
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
4.0
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
6.5
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
15
25
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter L).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
10
15
25
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
1.5
0 3
52
0.40
Use
Code
Letter
G
0 2
39
Less than
0.40
# 2
0.40
Higher
than
25
91
78
65
52
39
26
13
64
32
50
size
Cumu-
Higher lative
than
sample
25
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.25
26
13
64
32
50
Ac Re
47
PLANS
0.65
1.0
1.5
2.5
10
12
4.0
14
16
6.5
18
20
10
22
24
26
28
30
32
15
INDIVIDUAL PLANS
34
36
38
0.0641 0.446
3.33
4.78
5.79
8.01
1.0
0.132
0.359
0.863
1.72
2.84
3.68
5.59
0.25
95.0
90.0
75.0
50.0
25.0
10.0
5.0
1.0
2.09
1.201
0.667
0.0126 0.187
99.0
0.65
1.5
10.1
7.66
6.52
4.84
3.33
2.16
1.39
1.03
0.550
1.0
4.0
5.07
5.91
7.50
9.55
5.30
7.06
3.18
4.57
6.5
23.2
29.5
26.0
24.2
21.3
18.3
15.5
13.2
11.9
9.76
10
0.65
0.25
5.76
3.74
2.88
1.73
0.866
0.360
0.132
0.064
1.0
8.30
5.93
4.86
3.37
2.10
1.20
0.665
0.444
0.0126 0.186
0.15
1.5
10.5
7.87
6.65
4.90
3.34
2.16
1.38
1.02
0.545
1.0
2.5
4.0
6.5
4.98
5.82
3.27
3.94
1.71
7.45
9.59
12.1
5.27
7.09
9.28
6.39
2.5
4.0
20.0
16.4
16.4
13.1
9.69
12.6
14.7
11.6
8.35
3.17
4.59
2.18
3.63
2.23
1.03
9.61
25.2
6.5
21.2
21.8
19.3
16.3
13.3
10.8
10
28.5
24.3
22.2
19.0
15.8
13.0
10.8
7.71
8.78
7.62
X
5.96
18.0
16.2
13.5
10.8
8.55
6.79
5.87
4.38
1.5
10
26.6
20.3
23.6
21.4
18.6
15.8
13.2
11.0
9.89
7.93
18.6
16.0
13.3
10.9
8.95
7.91
6.17
6.5
Note: Binomial distribution used for percent nonconforming computations; Poisson for nonconformities per hundred units.
4.0
2.5
20.5
17.3
15.7
13.3
10.8
8.61
6.90
6.00
4.51
18.9
15.8
12.7
9.41
15.6
14.3
8.16
12.0
11.9
9.14
11.3
6.30
2.20
1.73
3.99
3.73
2.28
p (in percent
nonconforming)
2.5
3.32
1.04
1.5
TABLE X-J-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
31.8
27.4
25.2
21.7
18.3
15.3
12.9
11.6
9.35
10
40
15
38.2
33.4
30.9
27.2
23.3
19.9
17.1
15.6
12.9
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
0.15
0.15
Pa
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
42.9
37.8
35.2
31.2
27.1
23.4
20.3
18.6
15.7
15
PLANS
48
Multiple
Double
Single
Type of
sampling
plan
0.40
0.65
X
0.40
Use
Code
Letter
L
0.65
Use
Code
Letter
K
# 2
1 2
0 2
1 2
1 3
1 3
2 3
100
120
140
1.0
1.5
2.5
4.0
X
6.5
1.5
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
2.5
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
4.0
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
10
15
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter M).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
6.5
10
15
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
1.0
0 3
80
0.25
Use
Code
Letter
H
0 2
60
Less than
0.25
# 2
0.25
Higher
than
15
140
120
100
80
60
40
20
100
50
80
size
Cumu-
Higher lative
than
sample
15
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.15
40
20
100
50
80
Ac Re
49
PLANS
0.0
2.5
5.0
1.5
7.5
2.5
10.0
4.0
12.5
6.5
15.0
17.5
20.0
10
22.5
25.0
0.769
1.38
5.04
6.72
1.0
3.80
5.31
0.65
3.68
0.15
1.5
2.5
4.0
6.5
2.5
10.5
8.41
7.42
5.94
4.54
3.38
2.52
2.09
1.43
13.9
4.0
11.5
10.4
8.64
6.94
5.47
4.35
3.76
2.81
12.8
10.5
9.42
7.75
6.14
4.76
3.72
3.18
2.32
16.1
13.6
12.3
10.4
8.53
6.90
5.62
4.94
3.82
6.5
18.3
15.6
14.2
12.2
10.1
8.34
6.92
6.15
4.88
1.5
8.04
6.20
5.34
4.09
2.94
2.03
1.40
1.09
0.659
20.4
17.5
16.1
13.9
11.7
9.79
8.24
7.40
5.98
27.5
24.5
24.2
21.4
10
20.0
22.54
19.8
17.3
14.9
13.0
11.9
10.1
10
17.4
14.9
12.7
10.9
9.95
8.28
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
4.26
3.14
2.14
2.40
3.11
2.15
1.34
1.0
0.555
50.0
0.882
0.654
5.0
0.230
75.0
0.425
0.284
1.11
0.0843
90.0
1.0
1.84
0.0410
95.0
0.119
0.65
10.0
0.00804
99.0
0.40
25.0
0.10
Pa
TABLE X-K-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
100
INDIVIDUAL PLANS
PLANS
50
Multiple
Double
Single
Type of
sampling
plan
0.25
0.40
X
0.25
Use
Code
Letter
M
0.40
Use
Code
Letter
L
# 2
1 2
0 2
1 2
1 3
1 3
2 3
160
192
224
0.65
1.0
1.5
2.5
X
4.0
1.0
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
1.5
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
2.5
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
6.5
10
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter N).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
4.0
6.5
10
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.65
0 3
128
0.15
Use
Code
Letter
J
0 2
96
Less than
0.15
# 2
0.15
Higher
than
10
224
192
160
128
96
64
32
160
80
125
size
Cumu-
Higher lative
than
sample
10
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.10
64
32
160
80
125
Ac Re
51
PLANS
10
20
30
40
50
60
70
80
90
100
0.0
0.25
2.0
0.40
0.65
3.0
4.0
1.0
5.0
1.5
6.0
2.5
7.0
8.0
9.0
4.0
10.0
11.0
12.0
6.5
INDIVIDUAL PLANS
13.0
14.0
15.0
3.15
4.20
0.65
2.37
3.32
0.40
0.693
1.15
1.50
2.30
1.0
10.0
5.0
1.0
2.66
1.96
1.0
1.5
2.5
4.0
1.0
1.5
6.55
5.26
4.64
3.71
2.84
2.11
1.58
1.31
0.893
8.70
2.5
7.22
6.50
5.40
4.33
3.42
2.72
2.35
1.75
8.00
6.57
5.89
4.84
3.83
2.98
2.33
1.99
1.45
10.1
8.48
7.70
6.51
5.33
4.31
3.51
3.08
2.39
4.0
11.4
9.72
8.89
7.61
6.33
5.21
4.32
3.84
3.05
5.02
3.88
3.34
2.55
1.84
1.27
0.872
0.683
0.412
12.7
10.9
10.1
8.70
7.33
6.12
5.15
4.62
3.74
6.5
15.3
13.3
12.4
10.9
9.33
7.95
6.84
6.22
5.17
17.2
15.1
14.1
12.5
10.8
9.34
8.12
7.45
6.29
6.5
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
1.94
1.35
1.34
0.864
25.0
0.481
0.144
0.551
0.409
0.218
0.347
0.839
0.65
0.40
50.0
0.266
0.178
0.0743
0.25
75.0
0.0256
0.0527
90.0
0.00503
99.0
95.0
0.065
Pa
TABLE X-L-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
1.0
0.065
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
16.0
PLANS
52
Multiple
Double
Single
Type of
sampling
plan
0.25
X
0.15
Use
Code
Letter
N
0.25
Use
Code
Letter
M
# 2
1 2
0 2
1 2
1 3
1 3
2 3
250
300
350
0.40
0.65
1.0
1.5
X
2.5
0.65
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
1.0
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
1.5
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
4.0
6.5
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter P).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
2.5
4.0
6.5
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.40
0 3
200
0.10
Use
Code
Letter
K
0 2
150
Less than
0.10
0.15
# 2
Higher
than
6.5
350
300
250
200
150
100
50
250
125
200
size
Cumu-
Higher lative
than
sample
6.5
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.10
100
50
250
125
200
Ac Re
53
PLANS
10
20
30
40
50
60
70
80
90
100
0.0
0.040
1.0
2.0
0.65
3.0
1.0
4.0
1.5
5.0
2.5
6.0
7.0
8.0
4.0
9.0
10.0
0.305
2.67
0.40
2.11
0.25
0.951
1.46
0.065
1.0
0.65
1.0
1.5
2.5
2.00
1.0
4.16
3.34
2.94
2.36
1.80
1.34
1.00
0.830
0.567
5.52
1.5
4.58
4.13
3.43
2.75
2.17
1.72
1.49
1.11
5.08
4.17
3.74
3.07
2.43
1.89
1.48
1.26
0.923
6.40
5.38
4.89
4.13
3.39
2.74
2.23
1.96
1.51
2.5
7.24
6.17
5.64
4.83
4.02
3.31
2.74
2.44
1.94
0.65
3.19
2.46
2.12
1.62
1.17
0.805
0.554
0.434
0.261
8.08
6.95
6.39
5.52
4.66
3.89
3.27
2.94
2.37
9.60
10.9
8.47
9.71
8.95
4.0
7.92
7.86
6.88
5.93
5.16
4.73
3.99
4.0
6.90
5.93
5.05
4.34
3.95
3.28
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
1.51
1.69
1.24
5.0
1.23
0.855
0.849
0.548
0.440
0.533
0.350
0.260
0.138
0.731
0.220
50.0
0.40
0.25
10.0
0.0913
75.0
0.169
0.113
0.0472
0.15
25.0
0.0163
0.0335
90.0
0.0039
99.0
95.0
0.040
Pa
TABLE X-M-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
INDIVIDUAL PLANS
PLANS
54
Multiple
Double
Single
Type of
sampling
plan
0.15
X
0.10
Use
Code
Letter
P
0.15
Use
Code
Letter
N
# 2
1 2
0 2
1 2
1 3
1 3
2 3
400
480
560
0.25
0.40
0.65
1.0
X
1.5
0.40
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
0.65
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
1.0
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
2.5
4.0
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter Q).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
1.5
2.5
4.0
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.25
0 3
320
0 2
Less than
0.065
0.065
Use
Code
Letter
L
240
# 2
0.10
Higher
than
4.0
560
480
400
320
240
160
80
400
200
315
size
Cumu-
Higher lative
than
sample
4.0
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
160
80
400
200
315
Ac Re
55
PLANS
0.0
0.10
0.5
0.025
0.25
1.0
0.15
1.5
0.40
2.0
0.65
2.5
1.0
3.0
3.5
1.5
4.0
4.5
5.0
2.5
5.5
INDIVIDUAL PLANS
6.0
6.5
0.192
1.68
0.25
1.33
0.15
0.599
0.921
0.040
1.0
0.40
0.65
1.0
1.5
1.26
0.65
2.62
2.10
3.48
1.0
2.89
2.60
2.16
1.73
1.37
1.09
0.939
0.701
3.20
2.63
2.35
1.94
1.48
1.85
1.53
1.19
0.931
0.796
0.581
1.13
0.844
0.630
0.523
0.357
4.03
3.39
3.08
2.60
2.13
1.72
1.40
1.23
0.954
1.5
4.56
3.89
3.56
3.04
2.53
2.08
1.73
1.54
1.22
0.40
2.01
1.55
1.34
1.02
0.734
0.507
0.349
0.273
0.165
6.05
6.87
5.34
6.12
5.09
4.38
5.64
4.95
2.5
4.99
4.35
4.03
2.93
3.48
3.74
3.25
2.98
2.51
4.33
3.18
2.73
2.49
2.07
2.5
3.73
2.45
2.06
1.85
1.50
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
0.949
1.06
0.784
5.0
0.778
0.539
0.535
0.345
0.277
0.336
0.220
0.164
0.087
0.461
0.139
50.0
0.25
0.15
10.0
0.0575
75.0
0.106
0.0711
0.0297
0.10
25.0
0.0103
0.0211
90.0
0.00201
99.0
95.0
0.025
Pa
TABLE X-N-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
PLANS
56
Multiple
Double
Single
Type of
sampling
plan
0.10
X
0.065
Use
Code
Letter
R
0.10
Use
Code
Letter
Q
# 2
1 2
0 2
1 2
1 3
1 3
2 3
625
750
875
0.15
0.25
0.40
0.65
X
1.0
0.25
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
0.40
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
0.65
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
1.5
2.5
5 9
6 10
7 11
= Use single sampling plan above (or alternatively use code letter R).
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
1.0
1.5
2.5
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.15
0 3
500
0 2
Less than
0.040
0.040
Use
Code
Letter
N
375
# 2
0.065
Higher
than
2.5
875
750
625
500
375
250
125
630
315
500
size
Cumu-
Higher lative
than
sample
2.5
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
250
125
630
315
500
Ac Re
57
PLANS
0.0
0.5
0.15
1.0
0.25
0.40
1.5
0.65
2.0
1.0
2.5
3.0
1.5
3.5
INDIVIDUAL PLANS
4.0
0.120
1.05
0.15
0.830
0.10
0.374
0.576
0.025
1.0
0.25
0.40
0.65
1.0
0.787
0.40
1.64
1.31
2.18
0.65
1.80
1.62
1.35
1.08
0.855
0.679
0.587
0.438
2.00
1.64
1.47
1.21
0.928
1.16
0.959
0.745
0.582
0.498
0.363
0.709
0.527
0.394
0.327
0.223
2.52
2.12
1.93
1.63
1.33
1.08
0.878
0.771
0.596
1.0
2.85
2.43
2.22
1.90
1.58
1.30
1.08
0.961
0.762
0.25
1.26
0.969
0.835
0.630
0.459
0.317
0.218
0.171
0.103
3.78
4.29
3.34
3.82
3.18
2.74
3.52
3.09
1.5
3.12
2.72
2.52
1.83
2.17
2.34
2.03
1.86
1.57
2.71
1.99
1.71
1.56
1.29
1.5
2.33
1.53
1.29
1.16
0.935
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
0.593
0.490
0.665
5.0
0.486
0.337
0.334
0.216
0.173
0.210
0.138
0.102
0.0545
0.288
0.0866
50.0
0.15
0.10
10.0
0.0360
75.0
0.0665
0.0444
0.0186
0.065
25.0
0.00641
0.0132
90.0
0.00126
99.0
95.0
0.015
Pa
TABLE X-P-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
PLANS
58
Multiple
Double
Single
Type of
sampling
plan
0.065
X
0.040
Use
Code
Letter
R
0.065
Use
Code
Letter
Q
# 2
1 2
0 2
1 2
1 3
1 3
2 3
1000
1200
1400
0.10
0.15
0.25
0.40
X
0.65
0.15
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
0.25
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
0.40
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
X
1.0
1.5
5 9
6 10
7 11
Re = Rejection number.
Ac = Acceptance number.
9 14
11 16
10 11 12 13 14 15 18 19 21 22
9 12
6 11
4 9
2 7
0 4
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
0.65
1.0
1.5
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
= Use next subsequent sample size code letter for which acceptance and rejection numbers are available.
*
#
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.10
0 3
800
0 2
Less than
0.025
0.025
Use
Code
Letter
N
600
# 2
0.040
Higher
than
1.5
1400
1200
1000
800
600
400
200
1000
500
800
size
Cumu-
Higher lative
than
sample
1.5
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
400
200
1000
500
800
Ac Re
59
PLANS
0.0
0.2
0.4
0.6
0.15
0.8
0.25
1.0
0.40
1.2
1.4
0.65
1.6
1.8
2.0
1.0
2.2
INDIVIDUAL PLANS
2.4
2.6
0.0769
0.672
0.10
0.531
0.065
0.240
0.368
0.015
1.0
0.15
0.25
0.40
0.65
0.504
0.25
1.05
0.841
1.39
0.40
1.15
1.04
0.864
0.694
0.547
0.435
0.376
0.281
1.28
1.05
0.942
0.775
0.594
0.742
0.614
0.476
0.372
0.318
0.232
0.454
0.338
0.252
0.209
0.143
1.61
1.36
1.23
1.04
0.853
0.690
0.562
0.494
0.382
0.65
1.83
1.56
1.42
1.22
1.01
0.834
0.692
0.615
0.488
0.15
0.804
0.620
0.534
0.409
0.294
0.203
0.140
0.109
0.0659
2.04
1.0
2.45
2.14
1.98
1.75
1.74
1.61
1.49
1.27
1.09
0.995
0.828
1.39
1.17
0.979
0.824
0.740
0.598
2.75
2.42
2.25
2.00
1.73
1.49
1.30
1.19
1.01
1.0
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
0.380
0.314
0.426
5.0
0.311
0.215
0.214
0.138
0.111
0.134
0.0882
0.0654
0.0349
0.184
0.0555
50.0
0.10
0.065
10.0
0.0230
75.0
0.0425
0.0284
0.0119
0.040
25.0
0.00410
0.00843
90.0
0.000804
99.0
95.0
0.010
Pa
TABLE X-Q-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
PLANS
60
Multiple
0.015
X
0..025
0.040
0.065
0.10
0.15
0.25
X
0.40
X
0.65
Use
Code
Letter
P
0.025
Use
Code
Letter
S
0.040
Use
Code
Letter
R
# 2
1 2
0 2
1 2
1 3
1 3
2 3
1575
1890
2205
0.10
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
0.15
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
0.25
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
1.0
5 9
6 10
7 11
9 12
6 11
4 9
2 7
0 4
Re = Rejection number.
11 16
8 13
4 10
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
0.40
0.65
1.0
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
Ac = Acceptance number.
9 14
10 11 12 13 14 15 18 19 21 22
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.065
0 3
1260
0 2
0.015
945
*
#
Higher
than
1.0
2205
1890
1575
1260
945
630
315
1600
800
1250
size
Cumu-
Higher lative
than
sample
1.0
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
0.010
# 2
0.010
Use
Code
Letter
R
Ac Re
630
315
1600
800
1250
Single
Double
Cumulative
sample
size
Type of
sampling
plan
61
PLANS
10
20
30
40
50
60
70
80
90
100
0.1
0.025
0.2
0.040
0.3
0.065
0.4
0.10
0.5
0.15
0.6
0.25
0.7
0.8
0.9
0.40
1.0
1.1
1.2
INDIVIDUAL PLANS
0.65
1.3
1.4
1.5
0.0864
0.502
0.10
0.420
0.065
0.237
0.332
0.040
1.0
0.15
0.25
0.40
0.388
0.870
0.25
0.722
0.800
0.657
0.650
0.540
0.484
0.589
0.433
0.342
0.272
0.235
0.175
0.383
0.298
0.233
0.199
0.145
1.01
0.848
0.770
0.651
0.533
0.431
0.351
0.308
0.239
0.40
1.14
1.27
1.09
0.65
1.53
1.33
1.24
1.01
0.889
0.972
1.09
0.870
0.761
0.795
0.684
0.622
0.517
0.933
0.612
0.515
0.462
0.374
0.733
0.633
0.521
0.432
0.384
0.305
0.15
0.655
0.526
0.464
0.371
0.284
0.211
0.158
0.131
0.0893
1.72
1.51
1.41
1.25
1.08
0.934
0.812
0.745
0.629
0.65
Note: Values given in the table above are based on the Poisson distribution as an approximation to the binomial distribution (See 11.1 for details)
0.315
0.255
0.334
5.0
0.266
0.196
0.184
0.127
0.135
0.134
0.0872
0.0683
0.0412
0.194
0.0839
50.0
0.10
0.065
10.0
0.0481
75.0
0.0551
0.0409
0.0218
0.040
25.0
0.0178
0.0266
90.0
0.00743
99.0
95.0
0.025
Pa
TABLE X-R-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR SINGLE SAMPLING PLANS
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
0.0
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
PLANS
62
Multiple
0.010
0.015
X
0.025
0.040
0.065
0.10
0.15
X
0.25
X
0.40
0.015
Use
Code
Letter
P
0.025
Use
Code
Letter
S
# 2
1 2
0 2
1 2
1 3
1 3
2 3
2500
3000
3500
0.065
4 5
3 5
2 4
1 4
0 3
0 3
# 2
3 4
0 3
2 3
.010
6 7
4 6
3 6
2 5
1 4
0 3
# 3
4 5
1 4
3 4
0.15
9 10
7 9
5 8
3 7
2 6
1 5
# 4
6 7
2 5
5 6
5 9
6 10
7 11
9 14
9 12
6 11
4 9
2 7
0 4
8 13
4 10
Re = Rejection number.
9
7 14
11 17 13 19
6 12
10 15 12 17 16 22 19 25
7 12
3 9
0 6
11 15 14 17 17 20 22 25 25 29
8 13
6 10
3 8
0 5
0.25
0.40
0.65
13 14 14 15 18 19 21 22 25 26 32 33 37 38
= Use next preceding sample size code letter for which acceptance and rejection numbers are available.
Ac = Acceptance number.
11 16
10 11 12 13 14 15 18 19 21 22
11 12 12 13 15 16 18 19 23 24 26 27
3 7
8 9
10 12 12 14 14 17 18 20 21 23 27 29 31 33
7 11
5 10
0 4
8 9
3 7
7 8
0.040
0 3
2000
0.010
Use
Code
Letter
Q
0 2
1500
# 2
*
#
0.65
Higher
than
0.65
3500
3000
2500
2000
1500
1000
500
2500
1250
2000
size
Cumu-
Higher lative
than
0.65 sample
Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re Ac Re
1000
500
2500
1250
2000
Single
Double
Cumulative
sample
size
Type of
sampling
plan
63
PLANS
2
2
3
3
3
3
#
0
0
1
1
2
1600
2400
3200
4000
4800
5600
800
0.025
4000
2000
Re = Rejection number.
Ac = Acceptance number.
Multiple
Double
2000
Single
Re
X
Ac
Cumulative
sample
size
Type of
sampling
plan
AOQL
SCHEME
PERFORMANCE
64
Code
Letter
.019
.030
.048
.046
.078
.077
.072
.13
.13
.12
.12
0.25
0.40
(1.2)
1.2
0.65
(1.9)
1.9
1.0
(2.8)
2.9
1.5
(4.4)
4.7
2.5
.20
.21
.20
.20
.18
.31
.32
.32
.31
.31
.29
.45
.49
.49
.51
.50
.48
.46
.71
.72
.76
.78
.80
.78
.77
1.2
1.2
1.3
1.3
1.3
1.3
1.8
1.8
2.0
2.0
2.1
2.9
2.9
3.1
3.2
(2.9)
2.9
(.74)
(1.8) (3.0)
.75
1.8
3.0
(.47)
(1.2) (2.0) (3.2)
.47
1.2
2.0
3.1
(.30)
(.72) (1.2) (2.0) (3.2)
.30
.72
1.2
2.0
3.2
0.15
4.5
4.5
4.9
(4.5)
4.5
(4.9)
4.8
(4.9)
4.9
(5.1)
5.1
(5.0)
4.9
(6.8)
7.5
4.0
7.1
7.2
(7.0)
7.0
(7.5)
7.4
(7.9)
7.8
(8.7)
7.9
(8.0)
7.8
(7.7)
7.6
(11)
13
6.5
12
(12)
12
(13)
12
(13)
12
(14)
13
(13)
13
(13)
13
(12)
12
10
29
18
45
45
47
49
51
52
48
40
71
69
76
78
84
78
65
110
120
130
130
130
100
170
180
180
210
200
150
28
18
18
31
30
32
31
32
30
25
20
20
20
20
19
15
Note: For a better approximation to the AOQL, the above values must be multiplied by 1
.029
.047
.075
.12
.19
(In nonconformities per hundred units, also applicable to percent nonconforming for AQL less than 15
with specific values for percent nonconforming shown in parentheses)
260
270
290
300
310
250
Table XIAverage Outgoing Quality Limit Factors for ANSI-Z1.4 Scheme Performance
410
430
480
450
400
660
710
710
650
1100
1100
1000
LQ 10%
SCHEME
PERFORMANCE
65
Code
Letter
.115
.184
.123
.288
.194
.194
.460
.266
.311
.311
.731
.334
.426
.486
.486
1.15
.464
.534
.665
.778
.778
(1.83)
1.84
0.15
.650
.742
.835
1.06
1.23
1.23
(2.84)
2.88
0.25
.889
1.04
1.16
1.34
1.69
1.94
1.94
(4.50)
4.60
0.40
(10.9)
11.5
1.0
1.24
1.42
1.62
1.85
2.12
2.66
3.11
1.98
2.22
2.60
2.94
3.34
4.26
(4.77)
4.86
(3.08) (4.77)
3.11 4.86
(6.94)
7.19
0.65
3.09
3.56
4.13
4.64
5.34
(7.56)
7.78
(7.56)
7.78
(6.52)
6.65
(16.2)
17.7
1.5
4.95
5.64
6.50
7.42
(11.6)
12.2
(11.6)
12.2
(10.3)
10.6
(8.16)
8.35
(25.0)
28.8
2.5
7.86
8.89
10.4
(18.1)
19.4
(18.1)
19.4
(15.8)
16.6
(12.9)
13.4
(11.3)
11.6
(36.9)
46.0
4.0
12.4
14.2
(26.8)
29.9
(26.8)
29.9
(24.5)
26.6
(19.7)
20.9
(17.8)
18.5
(15.7)
16.2
(53.6)
76.7
6.5
10
19.8
(40.6)
48.6
(40.6)
48.6
(36.0)
40.9
(30.4)
33.4
(27.1)
29.0
(24.7)
26.0
(21.4)
22.2
30.9
35.6
40.6
46.4
51.4
66.5
77.8
77.8
15
49.5
55.6
65.0
71.3
83.5
106
130
130
25
77.4
88.9
100
116
134
177
194
40
124
137
162
185
223
266
65
190
222
260
309
334
100
269
309
356
433
464
150
(In nonconformities per hundred units, also applicable to percent nonconforming for AQL less than 15
with specific values for percent nonconforming shown in parentheses)
388
437
495
593
650
250
Table XIILimiting Quality for ANSI-Z1.4 Scheme Performance for Which Pa = 10 Percent
631
699
825
889
400
1000
1010
1170 1680
1240 1750
650
LQ 5%
SCHEME
PERFORMANCE
66
Code
Letter
.150
.240
.151
.374
.237
.237
.599
.315
.379
.379
.951
.388
.504
.593
.593
1.50
.526
.620
.787
.949
.949
(2.37)
2.40
0.15
.722
.841
.969
1.26
1.51
1.51
(3.68)
3.74
0.25
.972
1.15
1.31
1.55
2.00
2.37
2.37
(5.81)
5.99
0.40
(13.9)
15.0
1.0
1.33
1.56
1.80
2.10
2.46
3.15
3.79
2.14
2.43
2.89
3.34
3.88
5.04
(5.79)
5.93
(3.74) (5.79)
3.79 5.93
(8.94)
9.36
0.65
3.34
3.89
4.58
5.26
6.20
(9.14)
9.49
(9.14)
9.49
(7.66)
7.87
(20.6)
23.0
1.5
5.34
6.17
7.22
8.41
(14.0)
14.8
(14.0)
14.8
(12.1)
12.6
(9.41)
9.69
(31.2)
37.4
2.5
8.47
9.72
11.5
(21.6)
23.7
(21.6)
23.7
(18.4)
19.7
(14.8)
15.5
(12.7)
13.1
(45.1)
59.9
4.0
13.3
15.6
(31.6)
36.5
(31.6)
36.5
(28.3)
31.5
(22.5)
24.2
(19.9)
21.0
(17.3)
18.0
(63.2)
99.8
6.5
10
21.4
(47.1)
59.3
(47.1)
59.3
(41.0)
48.4
(34.4)
38.8
(30.1)
32.9
(27.0)
28.9
(23.2)
24.3
33.4
38.9
45.1
52.6
59.6
78.7
94.9
94.9
15
53.4
60.8
72.2
80.9
96.9
126
158
158
25
83.4
97.2
111
131
155
210
237
40
133
150
180
210
258
315
65
205
243
289
350
388
100
286
334
389
481
526
150
(In nonconformities per hundred units, also applicable to percent nonconforming for AQL less than 15
with specific values for percent nonconforming shown in parentheses)
409
465
534
648
722
250
Table XIIILimiting Quality for ANSI-Z1.4 Scheme Performance for Which Pa = 5 Percent
665
745
890
972
400
1000
1060
1240 1770
1340 1860
650
Table XIVAverage Sample Size Tables for ANSI-Z1.4 Scheme Performance (Single Sampling)
TABLE XIVA Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code A
6.5
6.5
25
40
65
100
150
250
400
650
1000
*
99.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
95.0
2.1
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
90.0
2.1
2.1
2.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
75.0
2.5
2.5
2.5
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
50.0
2.9
2.9
2.9
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
25.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
10.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
5.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
TABLE XIVB Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code B
4.0
4.0
15
25
40
65
100
150
250
400
650
1000
*
99.0
2.1
2.1
2.7
2.6
2.5
2.7
2.4
2.7
2.5
2.7
2.4
2.7
95.0
2.6
2.6
3.1
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
90.0
3.1
3.1
3.3
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
75.0
4.0
4.0
4.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
50.0
4.8
4.8
4.8
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
25.0
5.0
5.0
5.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
10.0
5.0
5.0
5.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
5.0
5.0
5.0
5.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
1.0
5.0
5.0
5.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
TABLE XIVC Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code C
2.5
10
2.5
10
15
25
p (in percent
nonconforming)
40
65
100
150
250
400
650
99.0
2.4
3.7
2.4
3.6
3.5
4.0
4.2
4.1
4.1
4.2
4.3
4.0
3.4
95.0
3.6
4.8
3.6
4.8
4.8
4.9
5.0
5.0
5.0
5.0
5.0
5.0
5.0
90.0
4.7
5.4
4.7
5.4
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
75.0
6.5
6.5
6.5
6.6
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
50.0
7.8
7.7
7.8
7.7
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
25.0
8.0
8.0
8.0
8.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
10.0
8.0
8.0
8.0
8.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
8.0
8.0
8.0
8.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
1.0
8.0
8.0
8.0
8.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
TABLE XIVD Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code D
1.5
6.5
10
1.5
6.5
10
p (in percent
nonconforming)
15
25
40
65
100
150
250
400
99.0
3.7
5.8
5.3
3.7
5.7
5.1
6.2
6.6
6.6
5.9
5.8
7.0
6.1
5.4
95.0
5.7
7.7
7.4
5.7
7.6
7.2
7.8
7.9
8.0
7.9
7.9
8.0
8.0
7.9
90.0
7.4
8.6
7.9
7.4
8.6
7.8
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
75.0
11
11
8.0
11
11
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
50.0
13
13
8.0
13
13
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
25.0
13
13
8.0
13
13
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
13
13
8.0
13
13
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
5.0
13
13
8.0
13
13
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
1.0
13
13
8.0
13
13
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
67
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
AVERAGE
SAMPLE
SIZE SCHEME
PERFORMANCE
Table XIVAverage Sample Size Tables for ANSI-Z1.4 Scheme Performance (Single Sampling)
TABLE XIVE Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code E
1.0
4.0
6.5
10
1.0
4.0
6.5
99.0
6.0
95.0
9.2
9.4
8.6
10
15
25
40
65
100
150
11
6.0
12
12
13
9.2
10
11
10
10
11
12
9.3
12
8.4
13
13
13
13
9.8
13
8.9
13
13
13
12
14
13
13
12
14
13
13
13
13
13
13
13
13
13
75.0
17
17
13
13
17
17
13
13
13
13
13
13
13
13
13
50.0
19
19
13
13
19
19
13
13
13
13
13
13
13
13
13
25.0
20
20
13
13
20
20
13
13
13
13
13
13
13
13
13
10.0
20
20
13
13
20
20
13
13
13
13
13
13
13
13
13
5.0
20
20
13
13
20
20
13
13
13
13
13
13
13
13
13
1.0
20
20
13
13
20
20
13
13
13
13
13
13
13
13
13
Code F
.65
2.5
4.0
6.5
10
.65
2.5
4.0
6.5
10
15
25
40
65
9.5
14.6
13.4
15.7
17.9
9.5
14.5
13.2
15.3
16.8
17.8
16.2
15.1
15.7
95.0
14.4
19.1
18.5
19.5
19.0
14.4
19.0
18.3
19.3
19.8
20.0
19.9
19.8
19.9
90.0
18.6
21.5
19.7
19.9
20.0
18.6
21.5
19.6
19.9
20.0
20.0
20.0
20.0
20.0
75.0
26.1
26.2
20.0
20.0
20.0
26.0
26.2
20.0
20.0
20.0
20.0
20.0
20.0
20.0
50.0
31.0
30.9
20.0
20.0
20.0
31.0
30.9
20.0
20.0
20.0
20.0
20.0
20.0
20.0
25.0
32.0
32.0
20.0
20.0
20.0
32.0
32.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
10.0
32.0
32.0
20.0
20.0
20.0
32.0
32.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
5.0
32.0
32.0
20.0
20.0
20.0
32.0
32.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
1.0
32.0
32.0
20.0
20.0
20.0
32.0
32.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
TABLE XIVG Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
8.6
90.0
TABLE XIVF Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
250
Code G
.4
1.5
2.5
4.0
6.5
10
.4
1.5
2.5
4.0
6.5
10
15
25
40
15.5
25.1
21.4
25.0
28.1
28.6
15.5
24.9
21.3
24.6
27.1
27.0
26.8
24.4
26.3
95.0
23.1
31.7
29.5
31.2
31.9
32.0
23.1
31.7
29.4
31.0
31.7
31.8
31.9
31.8
31.9
90.0
29.7
34.6
31.4
31.9
32.0
32.0
29.7
34.6
31.4
31.8
32.0
32.0
32.0
32.0
32.0
75.0
41.1
41.4
32.0
32.0
32.0
32.0
41.1
41.4
32.0
32.0
32.0
32.0
32.0
32.0
32.0
50.0
48.6
48.3
32.0
32.0
32.0
32.0
48.6
48.3
32.0
32.0
32.0
32.0
32.0
32.0
32.0
25.0
50.0
50.0
32.0
32.0
32.0
32.0
50.0
50.0
32.0
32.0
32.0
32.0
32.0
32.0
32.0
10.0
50.0
50.0
32.0
32.0
32.0
32.0
50.0
50.0
32.0
32.0
32.0
32.0
32.0
32.0
32.0
5.0
50.0
50.0
32.0
32.0
32.0
32.0
50.0
50.0
32.0
32.0
32.0
32.0
32.0
32.0
32.0
1.0
50.0
50.0
32.0
32.0
32.0
32.0
50.0
50.0
32.0
32.0
32.0
32.0
32.0
32.0
32.0
TABLE XIVH Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code H
.25
1.0
1.5
2.5
4.0
6.5
10
.25
1.0
1.5
2.5
4.0
6.5
10
15
25
23.8
36.3
35.6
40.3
43.1
42.4
43.4
23.8
36.2
35.3
39.8
42.1
40.8
40.5
41.9
42.7
95.0
36.0
47.7
47.8
49.2
49.7
49.8
50.0
36.0
47.6
47.7
49.0
49.6
49.6
49.8
49.9
50.0
90.0
46.5
53.7
49.6
49.9
50.0
50.0
50.0
46.5
53.7
49.6
49.9
49.9
50.0
50.0
50.0
50.0
75.0
65.1
65.6
50.0
50.0
50.0
50.0
50.0
65.1
65.6
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
77.6
77.1
50.0
50.0
50.0
50.0
50.0
77.6
77.2
50.0
50.0
50.0
50.0
50.0
50.0
50.0
25.0
79.9
79.9
50.0
50.0
50.0
50.0
50.0
79.9
79.9
50.0
50.0
50.0
50.0
50.0
50.0
50.0
10.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
5.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
80.0
80.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
AVERAGE
1.0
SAMPLE
SIZE SCHEME
PERFORMANCE
68
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
Table XIVAverage Sample Size Tables for ANSI-Z1.4 Scheme Performance (Single Sampling)
TABLE XIVJ Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code J
.15
.65
1.0
1.5
2.5
4.0
6.5
10
.15
.65
1.0
1.5
2.5
4.0
6.5
10
15
38.3
58.0
52.9
64.2
68.3
68.7
64.2
64.7
38.3
57.9
52.8
63.7
67.3
67.1
61.7
60.5
73.5
95.0
57.5
76.2
73.4
78.6
79.5
79.7
79.6
79.8
57.5
76.1
73.2
78.5
79.3
79.6
79.3
79.3
80.0
90.0
74.0
85.5
78.5
79.8
79.9
80.0
80.0
80.0
74.0
85.4
78.4
79.8
79.9
80.0
80.0
80.0
80.0
75.0
103
103
80.0
80.0
80.0
80.0
80.0
80.0
103
103
80.0
80.0
80.0
80.0
80.0
80.0
80.0
50.0
121
121
80.0
80.0
80.0
80.0
80.0
80.0
121
121
80.0
80.0
80.0
80.0
80.0
80.0
80.0
25.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
80.0
10.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
80.0
5.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
80.0
1.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
125
125
80.0
80.0
80.0
80.0
80.0
80.0
80.0
TABLE XIVK Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code K
.10
.40
.65
1.0
1.5
2.5
4.0
6.5
10
59.6
95.0
90.1
109
105
101
119
90.5
114
82.4
123
99.6
124
124
124
124
92.6
125
107
90.0
116
134
123
125
125
125
125
125
125
75.0
163
164
125
125
125
125
125
125
125
50.0
194
193
125
125
125
125
125
125
125
25.0
200
200
125
125
125
125
125
125
125
10.0
200
200
125
125
125
125
125
125
125
5.0
200
200
125
125
125
125
125
125
125
1.0
200
200
125
125
125
125
125
125
125
TABLE XIVL Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code L
.065
.25
.40
.65
1.0
1.5
2.5
4.0
6.5
132
153
168
178
162
151
157
95.0
144
190
183
193
198
200
199
198
199
90.0
185
214
196
199
200
200
200
200
200
75.0
258
260
200
200
200
200
200
200
200
50.0
306
304
200
200
200
200
200
200
200
25.0
315
315
200
200
200
200
200
200
200
10.0
315
315
200
200
200
200
200
200
200
5.0
315
315
200
200
200
200
200
200
200
1.0
315
315
200
200
200
200
200
200
200
99.0
95.6
TABLE XIVM Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Acceptance Quality Limits (normal inspection)
Pa
.04
.15
.25
.40
.65
1.0
1.5
2.5
4.0
149
244
207
240
264
263
268
242
263
95.0
226
312
288
304
312
313
314
313
315
90.0
292
342
309
313
315
315
315
315
315
75.0
408
411
315
315
315
315
315
315
315
50.0
485
483
315
315
315
315
315
315
315
25.0
500
499
315
315
315
315
315
315
315
10.0
500
500
315
315
315
315
315
315
315
5.0
500
500
315
315
315
315
315
315
315
1.0
500
500
315
315
315
315
315
315
315
69
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
Code M
AVERAGE
SAMPLE
SIZE SCHEME
PERFORMANCE
Table XIVAverage Sample Size Tables for ANSI-Z1.4 Scheme Performance (Single Sampling)
TABLE XIVN Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Pa
.025
.10
.15
.25
.40
.65
1.0
1.5
2.5
238
362
353
398
421
407
405
419
427
95.0
360
476
477
490
496
496
498
499
499
90.0
465
537
496
499
499
500
500
500
500
75.0
651
656
500
500
500
500
500
500
500
50.0
776
772
500
500
500
500
500
500
500
25.0
799
799
500
500
500
500
500
500
500
10.0
800
800
500
500
500
500
500
500
500
5.0
800
800
500
500
500
500
500
500
500
1.0
800
800
500
500
500
500
500
500
500
TABLE XIVP Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Pa
.015
.065
.10
.15
.25
.40
.65
1.0
1.5
378
576
523
634
670
667
610
598
730
95.0
572
759
730
784
793
795
792
793
800
90.0
738
854
784
798
799
800
800
800
800
75.0
1027
1035
800
800
800
800
800
800
800
50.0
1214
1208
800
800
800
800
800
800
800
25.0
1249
1249
800
800
800
800
800
800
800
10.0
1250
1250
800
800
800
800
800
800
800
5.0
1250
1250
800
800
800
800
800
800
800
1.0
1250
1250
800
800
800
800
800
800
800
Code Q
.01
.04
.065
.10
.15
.25
.40
.65
1.0
596
905
824
996
1090
1050
1010
926
1070
95.0
901
1190
1140
1230
1240
1240
1250
1240
1250
90.0
1160
1340
1230
1250
1250
1250
1250
1250
1250
75.0
1630
1640
1250
1250
1250
1250
1250
1250
1250
50.0
1940
1930
1250
1250
1250
1250
1250
1250
1250
25.0
2000
2000
1250
1250
1250
1250
1250
1250
1250
10.0
2000
2000
1250
1250
1250
1250
1250
1250
1250
5.0
2000
2000
1250
1250
1250
1250
1250
1250
1250
1.0
2000
2000
1250
1250
1250
1250
1250
1250
1250
TABLE XIVR Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code P
TABLE XIVQ Tabulated Values for Average Sample Size for ANSI-Z1.4 Scheme Performance
Code N
.025
.040
.065
.10
.15
.25
.40
.65
1450
1320
1530
1680
1780
1620
1510
1570
95.0
1900
1830
1930
1980
2000
1990
1980
1990
90.0
2140
1960
1990
2000
2000
2000
2000
2000
75.0
2600
2000
2000
2000
2000
2000
2000
2000
50.0
3040
2000
2000
2000
2000
2000
2000
2000
25.0
3150
2000
2000
2000
2000
2000
2000
2000
10.0
3150
2000
2000
2000
2000
2000
2000
2000
5.0
3150
2000
2000
2000
2000
2000
2000
2000
3150
2000
2000
2000
2000
2000
2000
2000
AVERAGE
1.0
SAMPLE
SIZE SCHEME
PERFORMANCE
70
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
Code R
71
SCHEME
PERFORMANCE
10
20
30
40
50
60
70
80
90
100
100
25
40
200
65
300
100
400
150
500
250
600
700
800
400
900
1000
1100
650
1200
1300
1400
1500
1600
1000
1700
1800
1900
2000
6.5
158
221
99.8
154
76.7
332
237
194
135
89.9
130
46.3
78.4
53.6
10.0
88.5
57.8
63.2
37.0
25.0
63.7
38.0
47.9
38.7
21.8
40
23.8
11.4
24.6
17.5
7.43
25
1.0
21.2
4.96
2.53
0.502
6.5
5.0
10.8
4.84
90.0
50.0
2.50
95.0
75.0
0.501
p (in percent
nonconforming)
99.0
Pa
420
315
266
196
138
103
79.9
66.1
41.2
65
502
388
334
256
195
162
138
123
89.1
100
250
400
650
655
526
464
372
294
248
214
192
145
871
722
650
540
443
380
333
302
239
1140
972
889
761
642
560
497
456
374
1530
1340
1240
1090
948
855
783
734
628
150
2090
1860
1750
1570
1400
1270
1180
1110
977
1000
TABLE XV-A-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
6.5
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
72
10
20
30
40
50
60
70
80
90
100
0.0
200
65
300
100
400
150
500
250
600
700
400
800
900
1000
1100
650
1200
1300
1400
1500
1600
1000
1700
1800
1900
2000
4.0
0.467
1.96
3.40
6.94
13.4
24.2
36.9
45.1
60.2
95.0
90.0
75.0
50.0
25.0
10.0
5.0
1.0
p (in percent
nonconforming)
99.0
Pa
77.8
94.9
46.0
59.9
133
53.9
92.2
35.1
27.8
23.8
15.9
11.6
5.46
15
14.4
7.19
3.46
1.98
0.468
4.0
221
158
280
210
177
92.0
131
59.0
89.9
130
68.8
53.3
44.4
31.4
40
42.4
31.9
25.8
16.2
25
335
258
223
171
130
108
92.2
81.9
60.2
65
150
250
400
437
350
309
248
196
165
143
128
92.5
581
481
433
360
295
253
222
201
154
761
648
593
507
428
373
332
304
244
1020
890
825
725
632
570
522
489
401
100
1390
1240
1170
1050
931
850
785
742
637
650
1950
1770
1680
1540
1400
1290
1200
1150
1010
1000
TABLE XV-B-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
100
4.0 15 25 40
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
73
SCHEME
PERFORMANCE
100
150
200
250
300
0.0
100
200
100
300
150
400
250
500
600
400
700
800
900
650
1000
1100
0.416
1.42
2.26
4.36
8.58
15.9
25.0
99.0
95.0
90.0
75.0
50.0
25.0
10.0
37.4
57.6
47.1
58.9
31.2
43.7
5.0
28.8
17.3
8.98
4.46
2.29
1.43
0.416
2.5
1.0
40.6
30.3
20.9
14.7
10.2
7.73
4.16
2.5
10
p (in percent
nonconforming)
Pa
83.0
59.3
48.6
33.07
21.8
14.6
9.79
7.29
3.83
10
133
94.9
77.8
53.9
35.4
25.5
19.2
15.7
10.8
15
168
126
106
78.5
55.2
41.3
32.0
26.6
18.4
25
65
100
150
250
201
155
134
102
77.8
64.7
55.3
49.2
37.7
262
210
185
149
117
99.0
85.7
76.9
61.3
348
289
260
216
177
152
133
121
100
457
389
356
304
257
224
199
183
154
612
534
495
435
379
342
313
294
256
40
835
745
699
627
559
510
471
445
399
400
1170
1060
1010
924
838
774
722
689
640
650
TABLE XV-C-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
50
0.0
10
30
30
10
40
40
20
50
50
20
60
60
65
70
70
40
80
80
25
90
90
2.5 10 15
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
1200
SCHEME
PERFORMANCE
74
0
0.0
100
65
200
100
300
150
400
250
500
600
400
12.7
21.3
30.3
40.6
47.1
58.9
13.1
19.4
26.8
31.6
41.3
16.2
20.6
29.8
10.0
5.0
1.0
16.2
6.26
9.10
5.38
75.0
7.86
10.7
10.1
2.73
90.0
2.55
4.73
25.0
1.43
95.0
6.5
10
p (in percent
nonconforming)
50.0
0.272
0.911
99.0
1.5
Pa
35.5
23.0
17.7
10.7
5.53
2.77
1.44
0.915
0.273
1.5
51.1
36.5
29.9
20.7
13.5
9.07
6.10
4.57
2.43
6.5
83.0
59.3
48.6
33.7
22.1
15.9
12.1
10.1
7.20
10
105
78.7
66.5
49.0
34.5
25.8
20.0
16.6
11.6
15
40
65
100
126
96.9
83.5
64.0
48.6
40.4
34.6
30.8
23.7
164
131
116
92.9
73.4
61.9
53.5
48.0
38.3
218
180
162
135
111
95.0
83.2
75.7
64.1
285
243
222
190
161
140
124
114
99.7
25
382
334
309
272
237
214
196
184
160
150
522
465
437
392
349
319
294
278
252
250
732
665
631
577
524
484
451
431
403
400
TABLE XV-D-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
10
20
30
30
20
40
40
40
50
50
25
60
60
15
70
70
10
80
80
6.5
90
90
1.5
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
700
75
SCHEME
PERFORMANCE
0.0
50
15 25
100
40
65
150
100
200
250
150
300
350
250
400
450
500
28.9
18.1
12.9
21.6
6.70
25.0
8.55
5.77
20.6
3.51
50.0
13.9
1.74
75.0
3.86
1.0
0.889
90.0
2.88
5.0
0.558
95.0
1.53
10.9
0.165
99.0
41.3
31.6
26.8
19.4
13.3
9.88
7.64
6.42
4.64
4.0
6.5
p (in percent
nonconforming)
10.0
1.0
Pa
50.6
41.0
36.0
28.0
20.7
16.2
12.9
10.9
7.62
10
23.1
15.0
11.5
6.94
3.58
1.75
0.893
0.560
0.165
1.0
33.2
23.7
19.4
13.5
8.70
5.76
3.80
2.82
1.48
4.0
51.1
36.5
29.9
20.7
13.6
9.80
7.42
6.19
4.41
6.5
15
25
40
65
64.7
48.4
40.9
30.2
21.2
15.9
12.3
10.2
7.13
77.3
59.6
51.4
39.4
29.9
24.9
21.3
18.9
14.4
101
80.9
71.3
57.2
45.2
38.1
32.9
29.6
23.7
134
111
100
83.1
68.1
58.4
51.2
46.6
39.3
176
150
137
117
98.8
86.2
76.5
70.6
62.2
10
235
205
190
167
146
132
120
113
100
100
321
286
269
241
215
196
181
171
153
150
TABLE XV-E-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
450
409
388
355
322
298
278
265
248
250
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10 15 20 25 30 35 40 45 50 55 60
0.0 5
10
30
30
10
40
40
20
50
50
20
60
60
10
70
70
6.5
80
80
4.0
90
90
1.0
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
76
40
50
0.0
20
40
15
60
25
80
40
100
65
120
140
160
1.11
2.22
4.24
6.94
8.94
90.0
75.0
50.0
25.0
10.0
5.0
13.4
0.571
95.0
1.0
0.104
0.357
99.0
.65
Pa
19.0
14.0
11.6
8.21
5.40
3.66
2.47
1.85
28.9
21.6
18.1
12.9
8.71
6.40
4.91
4.11
2.94
35.8
28.3
24.5
18.7
13.6
10.4
8.24
6.94
4.93
4.0
6.5
p (in percent
nonconforming)
.978
2.5
42.1
34.4
30.4
24.3
19.2
16.5
14.4
13.0
10.1
10
14.4
9.36
7.19
4.34
2.24
1.11
0.572
0.358
0.104
.65
20.7
14.8
12.2
8.43
5.46
3.66
2.45
1.82
.958
2.5
33.2
23.7
19.4
13.5
8.85
6.37
4.82
4.02
2.84
4.0
10
15
25
42.0
31.5
26.6
19.6
13.8
10.3
8.00
6.69
4.72
50.2
38.8
33.4
25.6
19.5
16.2
13.8
12.3
9.41
65.5
52.6
46.4
37.2
29.4
24.8
21.4
19.2
15.0
87.1
72.2
65.0
54.0
44.3
38.0
33.3
30.2
25.0
6.5
114
97.2
88.9
76.1
64.2
56.0
49.7
45.7
39.5
40
153
133
124
109
94.8
85.5
78.3
73.4
64.9
65
TABLE XV-F-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
20
0
10
0.0
10
10
30
30
20
40
40
20
50
50
10
60
60
6.5
70
70
4.0
80
80
2.5
90
90
0.65
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
77
SCHEME
PERFORMANCE
10
15
20
25
30
35
40
0.0
20
15
40
25
60
40
80
100
2.74
4.50
25.0
10.0
7.56
5.30
3.46
2.32
9.14
1.42
50.0
12.5
0.703
75.0
1.53
5.81
0.357
90.0
1.12
8.80
0.223
95.0
0.571
1.0
0.0643
99.0
1.5
5.0
.4
Pa
19.0
14.0
11.6
8.21
5.48
3.99
3.05
2.54
1.80
23.8
18.4
15.8
11.9
8.54
6.49
5.09
4.28
3.02
2.5
4.0
p (in percent
nonconforming)
28.1
22.5
19.7
15.5
12.1
10.2
8.87
7.96
6.12
6.5
36.0
30.1
27.1
22.3
18.2
15.7
13.9
12.6
10.0
10
9.22
5.99
4.60
2.78
1.43
0.706
0.358
0.223
0.0643
.4
13.3
9.49
7.78
5.39
3.48
2.32
1.52
1.11
.564
1.5
4.0
6.5
10
15
20.7
14.8
12.2
8.43
5.53
3.98
3.01
2.51
1.77
26.3
19.7
16.6
12.3
8.63
6.45
5.00
4.18
2.95
31.4
24.2
20.9
16.0
12.2
10.1
8.64
7.69
5.88
41.0
32.9
29.0
23.2
18.3
15.5
13.4
12.0
9.49
54.4
45.1
40.6
33.8
27.7
23.7
20.8
18.9
15.5
2.5
71.4
60.8
55.6
47.6
40.1
35.0
31.1
28.6
24.6
25
TABLE XV-G-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
95.6
83.4
77.4
67.9
59.2
53.4
48.9
45.9
40.3
40
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
10
0.0
20
30
30
20
40
40
10
50
50
6.5
60
60
4.0
70
70
2.5
80
80
1.5
90
90
0.4
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
78
10
20
30
40
50
60
70
80
90
100
0.0
.25
10
4.0
15
6.5
20
10
25
30
15
35
40
45
25
50
55
60
65
5.79
8.01
0.893
1.72
2.84
3.68
5.59
50.0
25.0
10.0
5.0
1.0
0.983
4.77
3.34
2.17
1.46
0.229
0.733
0.386
0.445
0.143
95.0
75.0
0.0416
99.0
1.0
90.0
.25
Pa
12.5
9.14
7.56
5.30
3.52
2.55
1.93
1.59
1.09
1.5
15.8
12.1
10.3
7.70
5.49
4.15
3.23
2.70
1.87
18.7
14.8
12.9
10.0
7.74
6.52
5.62
5.03
3.86
2.5
4.0
p (in percent
nonconforming)
24.1
19.9
17.8
14.5
11.7
10.0
8.76
7.92
6.33
6.5
31.6
27.0
24.7
21.0
17.6
15.4
13.7
12.6
10.4
10
5.76
3.74
2.88
1.73
0.898
0.446
0.229
0.143
0.0416
.25
8.30
5.93
4.86
3.37
2.18
1.46
0.979
0.729
0.383
1.0
2.5
4.0
6.5
13.3
9.49
7.78
5.39
3.54
2.55
1.92
1.57
1.08
16.8
12.6
10.6
7.85
5.52
4.13
3.20
2.66
1.84
20.1
15.5
13.4
10.2
7.78
6.47
5.53
4.92
3.77
26.2
21.0
18.5
14.9
11.7
9.90
8.57
7.69
6.14
1.5
34.8
28.9
26.0
21.6
17.7
15.2
13.3
12.1
10.0
10
45.7
38.9
35.6
30.4
25.7
22.4
19.9
18.3
15.4
15
TABLE XV-H-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
25
61.2
53.4
49.5
43.5
37.9
34.2
31.3
29.4
25.6
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
79
SCHEME
PERFORMANCE
.65
1.0
1.5
2.5
6.5
10
15
5.79
8.01
3.74
5.19
2.37
3.62
1.0
3.34
4.77
5.0
3.08
2.14
1.10
1.83
2.20
1.59
1.21
1.01
0.715
1.0
10.0
1.39
0.928
0.617
0.458
0.240
.65
25.0
0.282
0.144
90.0
0.571
0.0896
95.0
50.0
0.0260
99.0
75.0
.15
10.1
7.66
6.52
4.85
3.44
2.59
2.01
1.68
1.16
12.0
9.41
8.16
6.32
4.85
4.06
3.49
3.12
2.39
1.5
2.5
p (in percent
nonconforming)
15.6
12.7
11.3
9.15
7.31
6.23
5.43
4.89
3.88
4.0
20.5
17.3
15.7
13.3
11.0
9.58
8.48
7.74
6.49
6.5
26.6
23.2
21.4
18.6
16.0
14.2
12.7
11.8
10.2
10
3.69
2.40
1.84
1.11
0.573
0.282
0.144
0.0897
0.0260
.15
5.31
3.79
3.11
2.16
1.39
0.928
0.615
0.457
0.239
.65
2.5
4.0
8.30
5.93
4.86
3.37
2.21
1.59
1.20
1.00
0.710
10.5
7.87
6.65
4.90
3.45
2.58
2.00
1.66
1.15
12.6
9.69
8.35
6.40
4.86
4.04
3.46
3.08
2.35
16.4
13.1
11.6
9.29
7.34
6.19
5.35
4.80
3.80
1.0
21.8
18.0
16.2
13.5
11.1
9.50
8.32
7.56
6.35
6.5
TABLE XV-J-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
28.5
24.3
22.2
19.0
16.1
14.0
12.4
11.4
9.87
10
15
38.2
33.4
30.9
27.2
23.7
21.4
19.6
18.4
15.9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
4.0
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
0.0 1
.15
Pa
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
80
3.0
4.0
5.0
6.0
7.0
0.0
1.5 2.5
10
4.0
6.5
15
10
20
25
0.153
3.79
5.31
2.37
3.32
0.359
0.694
1.15
1.50
2.31
25.0
10.0
5.0
1.0
0.873
1.94
1.35
0.771
3.11
2.16
1.42
1.02
50.0
0.586
0.392
0.455
0.643
0.0916
0.292
0.178
0.0573
95.0
.65
75.0
0.0167
99.0
.40
90.0
.10
Pa
6.73
5.04
4.26
3.14
2.21
1.65
1.28
1.06
0.738
1.0
2.5
4.0
6.5
10
8.04
6.20
5.34
4.10
3.11
2.59
2.21
1.97
1.49
10.5
8.41
7.42
5.94
4.70
3.96
3.43
3.07
2.43
13.9
11.5
10.4
8.65
7.08
6.08
5.33
4.84
4.01
18.3
15.6
14.2
12.2
10.3
8.96
7.96
7.32
6.34
24.5
21.4
19.8
17.4
15.2
13.7
12.5
11.7
10.3
1.5
TABLE XV-K-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
0
1.0
0.0
10
30
30
10
40
40
20
50
50
20
60
60
1.0
70
70
0.65
80
80
0.40
90
90
0.10
100
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
81
SCHEME
PERFORMANCE
10
20
30
40
50
60
70
80
90
100
0.0
0.40
2.0
0.65
3.0
1.0
4.0
1.5
5.0
2.5
6.0
7.0
8.0
4.0
9.0
10.0
11.0
6.5
12.0
13.0
14.0
15.0
1.51
2.11
0.951
1.46
1.23
0.856
0.554
0.369
5.0
0.228
50.0
1.0
0.112
75.0
0.183
0.246
0.441
0.0574
90.0
0.731
0.0358
95.0
0.0957
10.0
0.0104
99.0
.25
25.0
.065
Pa
3.32
2.37
1.94
1.35
0.885
0.637
0.482
0.402
0.284
.40
4.20
3.15
2.66
1.96
1.38
1.03
0.800
0.669
0.472
.65
1.5
2.5
4.0
6.5
5.02
3.88
3.34
2.56
1.95
1.62
1.38
1.23
0.941
6.55
5.26
4.64
3.72
2.94
2.48
2.14
1.92
1.50
8.71
7.22
6.50
5.40
4.43
3.80
3.33
3.02
2.50
11.4
9.72
8.89
7.61
6.42
5.60
4.97
4.57
3.95
15.3
13.3
12.4
10.9
9.48
8.55
7.83
7.34
6.49
1.0
TABLE XV-L-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
1.0
.065 0.25
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
16.0
SCHEME
PERFORMANCE
82
10
20
30
40
50
60
70
80
90
100
0.0
1.0
2.0
.40 .65
1.0
3.0
1.5
4.0
5.0
2.5
6.0
7.0
4.0
8.0
9.0
10.0
0.949
1.33
0.0364
0.0711
0.143
0.278
0.460
0.599
0.922
90.0
75.0
50.0
25.0
10.0
5.0
1.0
0.0574
0.778
0.539
0.349
0.233
0.154
0.113
0.00665
0.0228
95.0
.15
99.0
.04
Pa
2.11
1.51
1.23
0.856
0.562
0.404
0.306
0.255
0.181
.25
2.67
2.00
1.69
1.25
0.876
0.655
0.508
0.425
0.300
.40
1.0
1.5
2.5
4.0
3.19
2.46
2.12
1.63
1.23
1.03
0.878
0.781
0.598
4.16
3.34
2.94
2.36
1.86
1.57
1.36
1.22
0.967
5.53
4.58
4.13
3.43
2.81
2.41
2.11
1.92
1.57
7.25
6.17
5.64
4.83
4.08
3.56
3.16
2.90
2.50
9.71
8.47
7.86
6.90
6.02
5.43
4.97
4.66
4.08
.65
TABLE XV-M-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
83
SCHEME
PERFORMANCE
0.0
0.5
.025 .10
.15
1.0
.25
.40
1.5
.65
2.0
1.0
2.5
3.0
1.5
3.5
4.0
4.5
2.5
5.0
5.5
6.0
6.5
0.174
0.288
25.0
10.0
0.486
0.337
0.218
0.146
0.593
0.0898
50.0
0.830
0.0446
75.0
0.0729
0.0979
0.374
0.0229
90.0
0.576
0.0143
95.0
0.0383
5.0
0.00416
99.0
.10
1.0
.025
Pa
1.33
0.949
0.778
0.539
0.354
0.255
0.192
0.157
0.108
.15
1.68
1.26
1.06
0.785
0.552
0.413
0.320
0.266
0.184
.25
.65
1.0
1.5
2.5
2.01
1.55
1.34
1.02
0.778
0.647
0.553
0.492
0.377
2.62
2.10
1.85
1.49
1.17
0.990
0.857
0.769
0.613
3.48
2.89
2.60
2.16
1.77
1.52
1.33
1.21
1.00
4.57
3.89
3.56
3.04
2.57
2.24
1.99
1.83
1.54
6.12
5.34
4.95
4.35
3.79
3.42
3.13
2.94
2.56
.40
TABLE XV-N-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
84
10
20
30
40
50
60
70
80
90
100
0.0
0.5
.015 .10
.25
.065 .15
1.0
.40
1.5
.65
2.0
1.0
2.5
1.5
3.0
3.5
4.0
0.379
0.531
0.00901
0.0144
0.0283
0.0573
0.111
0.184
0.240
0.369
95.0
90.0
75.0
50.0
25.0
10.0
5.0
1.0
0.311
0.216
0.139
0.0928
0.0616
0.0457
0.0240
0.00263
99.0
.065
.015
Pa
0.830
0.593
0.486
0.337
0.221
0.159
0.121
0.101
0.0713
.10
1.05
0.787
0.665
0.490
0.345
0.258
0.200
0.166
0.116
.15
.40
.65
1.0
1.5
1.26
0.969
0.835
0.640
0.486
0.404
0.346
0.308
0.236
1.64
1.31
1.16
0.929
0.734
0.619
0.535
0.480
0.381
2.18
1.80
1.62
1.35
1.11
0.950
0.832
0.757
0.636
2.85
2.43
2.22
1.90
1.61
1.40
1.24
1.14
0.989
3.82
3.34
3.09
2.72
2.37
2.14
1.96
1.84
1.59
.25
TABLE XV-P-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
85
SCHEME
PERFORMANCE
10
20
30
40
50
60
70
80
90
100
0.15
0.25
0.40
0.65
1.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6
.010
.065 0.10
.040
0.0694
0.115
25.0
10.0
0.0586
0.194
0.135
0.0873
0.237
0.0358
50.0
0.332
0.0178
75.0
0.0292
0.0392
0.150
0.00915
90.0
0.231
0.00573
95.0
0.0153
5.0
0.00167
99.0
.04
1.0
.01
Pa
0.531
0.379
0.311
0.216
0.142
0.102
0.0771
0.0643
0.0455
.065
0.673
0.504
0.426
0.314
0.221
0.165
0.128
0.106
0.0738
.10
.25
.40
.65
1.0
0.804
0.620
0.534
0.410
0.311
0.259
0.221
0.197
0.149
1.05
0.841
0.742
0.594
0.470
0.396
0.343
0.307
0.243
1.39
1.15
1.04
0.865
0.708
0.608
0.533
0.484
0.401
1.83
1.56
1.42
1.22
1.03
0.896
0.796
0.732
0.634
2.45
2.14
1.98
1.74
1.52
1.37
1.25
1.17
1.03
.15
TABLE XV-Q-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
SCHEME
PERFORMANCE
86
0.0
0.1
.025
.040
0.2
.065
0.3
0.10
0.4
0.15
0.5
0.25
0.6
0.7
0.8
0.40
0.9
1.0
1.1
0.65
1.2
1.3
1.4
1.5
0.0284
0.237
0.332
0.0554
0.0856
0.123
0.151
0.211
50.0
25.0
10.0
5.0
1.0
0.194
0.135
0.0885
0.0637
0.0482
0.0246
0.0402
0.0369
0.0183
95.0
75.0
0.00957
99.0
.040
90.0
.025
Pa
0.420
0.315
0.266
0.196
0.138
0.103
0.0800
0.0669
0.0473
.065
0.502
0.388
0.334
0.256
0.195
0.162
0.138
0.123
0.0941
.10
.25
.40
.65
0.656
0.526
0.464
0.372
0.294
0.248
0.214
0.192
0.150
0.871
0.722
0.650
0.540
0.443
0.380
0.333
0.302
0.250
1.14
0.972
0.889
0.761
0.642
0.560
0.497
0.457
0.395
1.53
1.33
1.24
1.09
0.948
0.855
0.783
0.734
0.649
.15
TABLE XV-R-1 TABULATED VALUES FOR OPERATING CHARACTERISTIC CURVES FOR ANSI Z1.4 SCHEME PERFORMANCE
Note: Figures on curves are Acceptance Quality Limits (AQLs) for normal inspection.
Quality of submitted product (p, in percent nonconforming for AQLs 10; in nonconformities per hundred units for AQLs >10)
10
20
30
40
50
60
70
80
90
100
PERCENT OF LOTS
EXPECTED TO BE
ACCEPTED (Pa)
(Curves for double and multiple sampling are matched as closely as practicable)
Paragraph
87
Licensed to intai technology corp./intai
ANSI Store order #X259177 Downloaded: 5/15/2006 10:07:34 PM ET
Single user license only. Copying and networking prohibited.
T004
Printed in the United States of America