Escolar Documentos
Profissional Documentos
Cultura Documentos
GAS TURBINE
DIVISION
Comqcessor Assemblies
are
affected
as follows:
Model Cl8 Series Cl8 C18A c20 c2o.B B15G 8178 8. Reason:
Compressor Serial
CAC CAC CAC CAC CAC CAC CAC 20001-21799 22000-23670 21900-21999 30000-32999, 33000-33209 50001-50107 80001-80176
Number
38001-38746
Compressor front ball bearing seals with wave washer type springs have caused engine rejections at acceptance test and fielcl operations. This seal configuration has shown to be slow in recovering during power transients. New seals incorporating conical wire springs have corrected this leakage problem.
C.
Description:
P/N 6871660 and 4871662 Seals (Gits Eros., L80201, P/N 38-062-07) with the wave washer type springs may be reworked to the conical wire configuration seal using P/N 23009626 Kit. Existing The seal and (3) kit consisting of (I) conical spring, be used to overhaul the
I
D. E.
Approval:
Compliance: Comply at
aspects
are
FAA
approved.
next
overhaul
following
parts availability.
15, No.
1976 3
1985
Commercial Engine
1. PLANNING INFORMATION: (Continued)
ALLISON
F. Manpower:
No additional G. Interchanqeability: All changes simultaneously, described i.e., in this bulletin must be incorporated assembly, and time required when accomplished
at overhaul.
be replaced
H.
as a set.
the spring,
seal ring
O-ring
must
Material
Availability:
Nomenclature
Seal Kit. Plain (Conical) Ring Assembly Encased
!?LY
1 1
O-ring
Seal
References:
AEM CW-1368A,
2.
ACCOM=LISHMENT A.
INSTRUCTIONS: and 6871662 (wave washer type spring) type seal using P/N 23009626 Seal Kit.
(1)
(2)
Remove retaining
ring
(See 16-120683
NEW CONICAL WAWER, SEAL RING ASSEMBLY AND O-RING MUST BE INSTALLED AS A SET. (3) Lightly lubricate new P/N 69PA017-VIT-70 O-ring with and install in new P/N 00-062106 Seal Ring Assembly. engine oil
November Revision
15, No.
I.976 3
2.
(Continued) Conical Spring seal case (or and P/N body). 00-62106 Seal Ring removed
Secme with
NOTE:
Check IO of retainer ring after assembly to be :sure not been damaged in removal or installation (rerrork necessary). (See Figure 1, New Configuration.)
(5)
Reidentify placing
in
as P/N
6887619
by tagging
6. Record compliance with Cl8 CEB-166, C2O/C2OB CEE1072, Bl5G TP CEB-24, or 817/817B TP CEB-1045 in the Compressor Assembly (blue pages) Modification Record, Part III of the Engine Log Book.
November
15,
1976
T63-A-5A,
T63-A-700
2.
ACCOMLISHMENT
INSTRUCTIONS:
(Continued)
16-120683 O-RING
--t---W
69PA017-V 'IT-70 O-RING
I l/II
III1
%--A
-RETAINING RING
1 +
1976 3
T63-A-5A,
250-C20, -C208,
-8178
T63-A-700 T63-A-720
1985
3. B.
MATERIAL Bill of
New P/N
!u 1
Fbmenclature
Seal, Plain-Encased
Q&Y 1
23009626 05-2582
69PA017-VIT-70
1
1
----
2 3 3 3
Spring O-ring
Seal Ring Assembly
1 1 1
1 1
DO-062106
INSTRUCTIONS/DISPOSITION 1.
NOTES:
Rework.
Added.
2. 3.
Scrap
removed
parts.
250-C18,
T63-A-5A,
T63-A-700 T63-A-720