Você está na página 1de 5

Supplemental Technical Specification for

Hot-Mix Asphalt Material Properties


SCDOT Designation: SC-M-402 (06/07)
1. 1.1 SCOPE Use the following specifications for preparing, constructing, and accepting Hot-Mix Asphalt (HMA) material properties. NOTE: Refer to the Standard Specifications, Division 300 for HMA Base Courses and Division 400 for HMA Surface and Intermediate Courses for additional properties and specifications that are not included here. REFERENCED DOCUMENTS SCDOT Standard Specifications Division 300, Division 400 AASHTO Standards T85, T96, T104, TP61 SCDOT Test Methods SC-T-77 REQUIREMENTS FOR MIXTURES Requirements for all HMA Have no more than 10% flat and elongated particles based on a 5:1 ratio based on SC-T77. Determine coarse aggregate Sodium Sulfate Soundness by AASHTO T 104. Determine LA Abrasion by AASHTO T 96. Determine Absorption by AASHTO T 85. The composition limits are master ranges of tolerances. Conform to a closer control meeting the tolerance requirements as specified in Section 401.2.3.3. VMA requirements for Surface and Intermediate Courses: Nominal Max. Aggregate Size 3/4" 1/2" 3/8" No. 4 1 Minimum, % 13.5 14.5 15.5 17.5

2. 2.1 2.1.1 2.2 2.2.1 2.3 2.3.1 3. 3.1 3.1.1

3.1.2 3.1.3 3.1.4 3.1.5

3.1.6

3.1.7

Use hydrated lime as an asphalt anti-stripping additive (ASA) in all mixes unless otherwise permitted in the following tables. If crushed stone is required in the following tables, use crushed coarse aggregate meeting the following requirements: Have 2 or more freshly mechanically-induced fractured faces meeting the percentage stated in each table based on count of the material retained on the No. 4 sieve as determined by AASHTO TP-61. Ensure the Recycled Asphalt Pavement (RAP) conforms to Subsection 401 of the Standard Specifications.

3.2

3.2.1

3.3

3.4

Summary of Surface Course Requirements


HMA Surface Courses Designation
Old Designation

Type A
12.5 mm Superpave

Type B

Type CM
Type 1D

Type C

Type D
Type 4

Type E
Thin Lift Seal Course

Surface Type Surface 1C

Surface Type Surface 1,3

System Application

Interstate / Intersections 100.0 98.0 100.0 90.0 100.0 72.0 - 90.0 44.0 - 62.0 23.0 43.0 10.0 25.0 4.0 - 12.0 2.00 - 8.00

High Volume Primary

Low Volume Primary

Secondary

Low Volume Secondary

Seal Course

1 3/8 No. 4 No. 8 No. 30 No. 100 No. 200

Gradation Requirements 100.0 ---98.0 100.0 100.0 90.0 100.0 97.0 100.0 72.0 - 90.0 83.0 100.0 44.0 - 62.0 58.0 80.0 23.0 - 43.0 42.0 62.0 10.0 - 25.0 20.0 40.0 4.0 - 12.0 8.0 20.0 2.00 - 8.00 3.00 9.00 Required Job Mix Criteria

---100.0 97.0 100.0 83.0 100.0 58.0 80.0 42.0 62.0 20.0 40.0 8.0 20.0 3.00 9.00

------100.0 ---97.0 100.0 ---90.0 100.0 100.0 70.0 95.0 90.0 100.0 50.0 82.0 70.0 100.0 20.0 50.0 36.0 70.0 6.0 20.0 4.0 28.0 2.00 10.00 2.00 10.00

Gyrations Binder Limits, % Binder Grade Air Voids, % VFA, % D/A Ratio Min. Stability 6 (lbs.) Rutting Susceptibility (max mm) Liquid ASA Permitted

100 4.5 - 6.0 PG 76-22 3.0 4.0 70.0 80.0 0.60 - 1.20

75 4.5 - 6.0 PG 64-22 3.0 4.0 70.0 80.0 0.60 - 1.20

75 5.0 - 6.8 PG 64-22 3.5 4.5 70.0 77.0 0.60 - 1.20

50 5.0 - 6.8 PG 64-22 3.5 4.5 70.0 77.0 0.60 - 1.20

50 5.0 - 6.8 PG 64-22 4.0 9.0 60.0 70.0 0.60 - 1.20

50 6.0 - 7.0 PG 64-22 NR NR NR 2500

No Requirement (NR) 3.0 No 5.0 No 5.0 No NR Yes NR Yes

NR Yes

Required Aggregate Criteria Local Sand Allowed? Crushed Coarse Aggr. Required? (% fractured faces) Coarse Aggr. Max. % Passing No.200 LA Abrasion (B), max % Sodium Sulfate Soundness, max % Crusher Run / Asphalt Sand Allowed? Absorption, max. % Limestone allowed (Coarse/Scrn.)? Slag Allowed? RAP No Yes (90% min) 1.50 55.0 15.0 No 1.5 No / No No No No Yes (90% min) 1.50 55.0 15.0 No 1.5 No / Yes No Yes No Yes (90% min) 1.50 55.0 15.0 No 1.5 No / Yes No Yes Yes Yes (70% min) 1.50 60.0 15.0 Yes (25% max) 1.5 No / Yes Yes Yes Yes No 1.50 60.0 NR Yes (50% max) NR Yes / Yes Yes Yes No NR NR 60.0 NR No 1.5 No No Yes (-4)

3.5

Summary of HMA Intermediate Course Requirements


HMA Intermediate Courses Designation
Old Designation

Type A
19.0 mm for Intersections

Type B
19.0 mm / Binder Type 1

Type C *
Binder Type 2

System Application

Intersections

Interstates / High Volume Primary (> 15% Truck Traffic) Gradation Requirements 100.0 90.0 - 100.0 75.0 90.0 64.0 80.0 38.0 54.0 22.0 36.0 8.0 22.0 3.0 10.0 2.00 - 8.00 Required Design Criteria 75 4.0 - 6.0 PG 64-22 3.5 - 4.5 70.0 80.0 0.60 - 1.20 No Requirement (NR)

Low Volume Primary / Secondary / Leveling / Patching

1 3/8 No. 4 No. 8 No. 30 No. 100 No. 200 Gyrations Binder Limits, % Binder Grade Air Voids, % VFA, % D/A Ratio Min. Stability (lbs.) Rutting Susceptibility (max mm) Liquid ASA Permitted

100.0 90.0 - 100.0 75.0 90.0 64.0 80.0 38.0 54.0 22.0 36.0 8.0 22.0 3.0 10.0 2.00 - 8.00 100 4.0 - 6.0 PG 76-22 3.0 - 4.0 70.0 80.0 0.60 - 1.20

100.0 90.0 100.0 80.0 95.0 68.0 87.0 45.0 68.0 30.0 46.0 12.0 29.0 4.0 13.0 2.00 8.00 50 4.0 - 6.0 PG 64-22 3.5 - 4.5 70.0 77.0 0.60 - 1.20

3.0 No

5.0 No Required Aggregate Criteria

NR Yes

Local Sand Allowed? Crushed Coarse Aggregate Required? (% fractured faces) Coarse Aggr. max. % Passing No. 200 LA Abrasion (B), max. % Sodium Sulfate Soundness, max % Crusher Run / Asphalt Sand Allowed? Absorption, max. % Limestone allowed (Coarse/Scrn.)? Slag Allowed? RAP

No Yes (90% min.) 1.5 55.0

No Yes (90% min.) 1.5 55.0 No Requirement (NR)

Yes No NR 60.0

No 1.5 No / No Yes No

No 1.5 No / Yes Yes Yes

Yes (50% max) NR Yes / Yes Yes Yes

* - Use Intermediate Type C for leveling, patching and other non-mainline type applications 4

3.6

Summary of HMA Base Course Requirements


HMA Base Courses Type B
Base Type 2

Designation
Old Designation

Type A
Base Type 1

Type C
Sand Base Type 3

Type D
Sand Base Type 2

System Application

Interstates / Primary

Secondary Gradation Requirements

Specialty

Specialty

1 1 3/8 No. 4 No. 8 No. 30 No. 100 No. 200

100.0 85.0 - 100.0 60.0 - 80.0 ---40.0 - 55.0 30.0 - 45.0 ----------

100.0 85.0 - 100.0 60.0 - 80.0 ---40.0 - 55.0 30.0 - 45.0 ---------Required Design Criteria

---------100.0 90.0 100.0 70.0 100.0 36.0 70.0 4.0 28.0 2.00 10.00

----------------------------

Gyrations Binder Limits, % Binder Grade Min. Stability, lbs. Rutting Susceptibility (max mm) Liquid ASA Permitted

---4.0 - 5.5 * PG 64-22 NR

---4.0 - 5.5 * PG 64-22 NR

50 4.3 - 5.7 PG 64-22 2500

50 3.8 - 5.2 PG 64-22 1500

No Requirement (NR) No Yes Required Aggregate Criteria Yes Yes

Local Sand Allowed? Crushed Coarse Aggregate Required? (% fractured faces) LA Abrasion (B), max. % Sodium Sulfate Soundness, max % Crusher Run / Asphalt Sand Allowed? Absorption, max. % Limestone allowed (Coarse/Scrn.)? Slag Allowed? RAP

No Yes (90% min) 60.0

Yes No 60.0

No No 60.0

Yes No 60.0

No Requirement (NR) Yes (50% max) Yes (50% max) No Requirement (NR) Yes / Yes Yes Yes Yes / Yes Yes Yes Yes / Yes Yes Yes (-4) Yes / Yes Yes Yes (-4) No No

* Binder content determined visually during design.

Você também pode gostar