Escolar Documentos
Profissional Documentos
Cultura Documentos
Monolithic Linear IC
LA76818A
Features
Single crystal multiformat system that supports the different TV broadcast formats used worldwide Multiformat system : LA76818A (YCbCr support) Adjustment-free VIF/SIF, audio trap/audio bandpass filters Adjustment-free horizontal resonator system Simplified SG Supply voltage : VCC = 5V/9V VIF/SIF Adjustment-free VCO, 4-mode audio trap/audio bandpass filter, buzz canceller RF AGC/video level SIF system automatic discrimination (The LA7973 is used as the automatic discrimination IC.) Single crystal color system: PAL, NTSC, SECAM (The LA7642N is used as the SECAM decoder.) Black stretch, sharpness control with coring on/off control, built-in variable Y system filters (Y-DL and chrominance trap) Chrominance bandpass filter, demodulation ratio and angle control
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment.
LA76818A
Specifications
Maximum Ratings at Ta = 25C
Parameter Maximum supply voltage Symbol V8 max V31 max V43 max Maximum supply current I18 max I25 max Allowable power dissipation Operating temperature Storage temperature Pd max Topr Tstg Ta 65C * Conditions Ratings 7.0 7.0 7.0 25 35 1.6 -10 to +65 -55 to +150 Unit V V V mA mA W C C
Electrical Characteristics Ta = 25C, VCCL = V8 = V31 = V43 = 5.0V, ICC = I18 = 19mA, ICC = I25 = 27mA
Parameter Circuit voltage, current IF supply current RGB supply voltage Horizontal supply voltage CCD supply current Video supply current VIF block Maximum RFAGC voltage Minimum RFAGC voltage RF AGC Delay Pt Input sensitivity No-signal video output voltage Sync signal tip level Video output amplitude Video S/N C-S beat level Differential gain Differential phase Maximum AFT output voltage Minimum AFT output voltage AFT detection sensitivity APC pull-in range (U) APC pull-in range (L) (@DAC = 0) (@DAC = 63) VRFH VRFL RFAGC0 RFAGC63 Vi VOn VOtip VO S/N IC-S DG DP VAFTH VAFTL VAFTS fPU fPL CW = 80dB, DAC = 0 CW = 80dB, DAC = 63 DAC = 0 DAC = 63 Output-3db No signal CW = 80dB 80dB, AM = 78%, fm = 15kHz CW = 80dB V4.43MHz/V1.07MHz 80dB, 87.5% Video MOD 80dB, 87.5% Video MOD CW = 80dB, frequency variations CW = 80dB, frequency variations CW = 80dB, frequency variations 4.3 0.0 8.0 1.0 1.0 3.4 1.1 1.95 40 35 5.0 1.0 4.7 0.3 15.0 10.0 10.0 5 0.7 22.0 3.7 1.4 2.05 45 8.5 0 90 80 46 4.0 1.7 2.15 9 0.3 0.7 Vdc Vdc dB dB dB Vdc Vdc Vp-p dB dB % deg Vdc Vdc mV/kHz MHz MHz I8 V18 V25 I31 I43 V8 = 5V, V3 = 2.5V I18 = 19mA I25 = 27mA I31 = 5V I43 = 5V 125.0 55.0 7.8 4.8 65.0 8.2 5.1 5.6 140.0 155.0 75.0 8.5 5.4 mA V V mA mA Symbol Conditions min Ratings typ max Unit
No.8047-2/44
LA76818A
Continued from preceding page.
Parameter NT Trap1 (4.5MHz) NT Trap2 (4.8MHz) BG Trap1 (5.5MHz) BG Trap2 (5.85MHz) I Trap1 (6.0MHz) I Trap2 (6.55MHz) DK Trap1 (6.5MHz) SIF block FM detection output voltage FM limiting sensitivity FM detection output f characteristics FM detection output distortion AM rejection ratio SIF S/N PAL de-emph time constant PAL/NT difference of voltage gain NT de-emph time constant AUDIO block Maximum gain Variable range Frequency characteristics Mute Distortion S/N Crosstalk Video block Video overall gain (Contrast max) Contrast adjustment Characteristics Video frequency characteristics PAL 6MHz Trap APF BW2 BW3 BW4 NTSC BW1 1.8MHz/100kHz Filter sys = 0000 2.2MHz/100kHz Filter sys = 0010 2.3MHz/100kHz Filter sys = 0100 3.4MHz/100kHz Filter sys = 0000 Y APF=1 Chroma trap amount DC transmission amount PAL NTSC 1 2 3 4 Y-DL TIME NTSC PAL SECAM 6MHz Trap APF CtrapP CtrapN ClampG1 ClampG2 ClampG3 ClampG4 TdY1 TdY2 TDY3 TdY4 TdY5 DCREST = 00 DCREST = 01 DCREST = 10 DCREST = 11 FILTER SYS = 0000 FILTER SYS = 0010 FILTER SYS = 1000 FILTER SYS = 0100 FILTER SYS = 0000, YAPF = 1 -36.0 -36.0 95.0 102.0 107.0 123.0 490.0 530.0 610.0 370.0 370.0 -26.0 -26.0 100.0 107.0 112.0 128.0 540.0 580.0 660.0 420.0 420.0 -22.0 -22.0 105.0 112.0 117.0 133.0 590.0 630.0 710.0 470.0 470.0 dB dB % % % % ns ns ns ns ns -6.0 -3.0 0.0 dB -6.0 -3.0 0.0 dB -6.0 -3.0 0.0 dB -6.0 -3.0 0.0 dB Normal/max Min/max) CONT63 CONT0 -7.5 -15.0 -6.0 -12.0 -4.5 -9.0 dB dB CONT127 10.0 12.0 14.0 dB AGMAX ARANGE AF AMUTE ATHD ASN ACT 20kHz 20kHz 1kHz, 500mVrms, Vol: MAX DIN.Audio 1kHz 65 70 73 1kHz, 500mVrms -2.0 60 -3.0 70 0.5 0.5 74 0.0 3.0 +3.0 dB dB dB dB % dB dB SNTC 1.9 2.5 3.1 dB STHD SAMR SSN SPTC SGD FM = 30kHz AM = 30% DIN.Andio 40 50 2.4 -1.5 3.0 0.0 3.6 +1.5 1.0 % dB dB dB dB SOADJ SLS SF FM = 30kHz Output -3dB fm = 100kHz -0.5 5.0 220 310 435 53 8.0 mVrms dB dB Symbol NTR1 NTR2 BTR1 BTR2 ITR1 ITR2 DTR1 Conditions min Ratings typ max -28 -20 -28 -20 -28 -17 -28 dB dB dB dB dB dB dB Unit
No.8047-3/44
LA76818A
Continued from preceding page.
Parameter Black stretch gain Max Mid Min Black stretch start point Max (60IRE V) Mid (50IRE V) Min (40IRE V) Sharpness variability range NTSC Sharpness variability range PAL Sharpness variability range SECAM Sharpness variability range 6MHz TRAP Trap 1 mid Trap 1 max Trap 1 min Trap 2 mid Trap 2 max Trap 2 min Trap 3 mid Trap 3 max Trap 3 min Trap 4 mid Trap 4 max Trap 4 min Sharpness variability range APF White peak limiter effective point Trap 5 mid Trap 5 max Trap 5 min 1 2 3 4 Y gamma effective point 1 2 3 Gray Mode Level Horizontal/vertical blanking output level Pre-shoot adjust 1 2 Over-shoot adjust OSD block OSD Fast SW threshold Red RGB output level Green RGB output level Blue RGB output level Analog OSD R output level Analog OSD G output level Analog OSD B output level Gain match Linearity Gain match Linearity Gain Match Linearity FSTH ROSDH GOSDH BOSDH RRGB LRRGB GRGB LGRGB BRGB LBRGB 0.7 120 70 85 1.12 45 0.8 45 0.8 45 0.9 165 120 120 1.4 50 1 50 1.0 50 1.1 200 140 155 1.68 60 1.2 60 1.2 60 V IRE IRE IRE Ratio % Ratio % Ratio % PreShoot1 PreShoot2 OverShoot Pre-shoot adj. = 00 Pre-shoot adj. = 11 Over-shoot adj. = 11 0.92 1.08 1.08 0.97 1.13 1.13 1.02 1.18 1.18 Sharp31T1 Sharp63T1 Sharp0T1 Sharp32T2 Sharp63T2 Sharp0T2 Sharp32T3 Sharp63T3 Sharp0T3 Sharp32T4 Sharp63T4 Sharp0T4 Sharp32T5 Sharp63T5 Sharp0T5 WPL1 WPL2 WPL3 WPL4 YG1 YG2 YG3 GRAY RGBBLK F = 2.2MHz, FILTER SYS = 0000 F = 2.2MHz, FILTER SYS = 0000 F = 2.2MHz, FILTER SYS = 0000 F = 2.7MHz, FILTER SYS = 0010 F = 2.7MHz, FILTER SYS = 0010 F = 2.7MHz, FILTER SYS = 0010 F = 2.3MHz, FILTER SYS = 1000 F = 2.3MHz, FILTER SYS = 1000 F = 2.3MHz, FILTER SYS = 1000 F = 3.0MHz, FILTER SYS = 0100 F = 3.0MHz, FILTER SYS = 0100 F = 3.0MHz, FILTER SYS = 0100 F = 3.0MHz, FILTER SYS = 0000 Y APF = 1 F = 3.0MHz, FILTER SYS = 0000 Y APF = 1 F = 3.0MHz, FILTER SYS = 0000 Y APF = 1 APL = 100% WPL = 00 APL = 100% WPL = 01 APL = 100% WPL = 10 APL = 100% WPL = 11 YGAMMA = 01 YGAMMA = 10 YGAMMA = 11 GLAY MODE = 1, CROSS B/W = 2 5.0 9.0 -5.0 5.0 8.5 -6.5 5.0 8.5 -6.5 5.0 8.5 -6.5 5.0 8.5 -6.5 160.0 130.0 100.0 70.0 89.0 85.0 80.0 12.5 0.1 8.0 12.0 -2.0 8.0 11.5 -3.5 8.0 11.5 -3.5 8.0 11.5 -3.5 8.0 11.5 -3.5 170.0 140.0 110.0 80.0 93.0 89.0 84.0 16.0 0.4 11.0 15.0 1.0 11.0 13.5 -0.5 11.0 13.5 -0.5 11.0 13.5 -0.5 11.0 13.5 -0.5 180.0 150.0 110.0 90.0 97.0 93.0 88.0 19.5 0.7 dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB IRE IRE IRE IRE % % % IRE V BKSTTHmin Bain = 01, Start = 00 -5.0 0.0 5.0 IRE BKSTTHmid Bain = 01, Start = 01 -5.0 0.0 5.0 IRE Symbol BKSTmax BKSTmid BKSTmin BKSTTHmax Conditions min Gain = 10, Start = 01 Gain = 01, Start = 01 Gain = 00, Start = 01 Bain = 01, Start = 10 27.0 19.0 9.0 -5.0 Ratings typ 32.0 24.0 14.0 0.0 max 37.0 29.0 19.0 5.0 IRE IRE IRE IRE Unit
No.8047-4/44
LA76818A
Continued from preceding page.
Parameter RGB output (cutoff drive) block Brightness control Normal Normal-H Hi brightness Max Low brightness Min Cutoff control (Bias control) Resolution Sub-bias control Resolution RB Drive adjustment Maximum output G Drive adjustment Maximum output RB Output attenuation G Output attenuation Video SW block Video signal input 1DC voltage Video signal input 1AC voltage Video signal input 2DC voltage Video signal input 2AC voltage SVO terminal DC voltage SVO terminal AC voltage Chroma block (PAL/NTSC common) B-Y/Y amplitude ratio Color control characteristics 1 Color control characteristics 2 Color control sensitivity fsc output level Residual higher harmonic level B Residual higher harmonic level R Residual higher harmonic level G Chroma block (PAL) ACC amplitude characteristics 1 ACC amplitude characteristics 2 Demodulation output ratio R-Y/B-Y: PAL Demodulation output ratio G-Y/B-Y: PAL Demodulation output ratio G-Y/R-Y: PAL Demodulation angle R-Y/B-Y: PAL Killer operating point 0 (PAL) Killer operating point 3 (PAL) Difference between two Killer operating points (PAL) APC pull-in range (+) APC pull-in range (-) PULIN+_P PULIN-_P 350 -350 Hz Hz KILLP0 KILLP3 DKILLP ANGRB_P GR_P GB_P ACCM1_P ACCM2_P RB_P Input: +6dB/0dB 0dB = 40IRE Input: -20dB/0dB R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center, R-Y = no-signal R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center, B-Y= no-signal R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center 0dB = 40IRE 0dB = 40IRE KILLP0-KILLP3 -37 -40 0.5 -25 -27 6.0 dB dB dB 85 90 95 deg -0.56 -0.51 -0.46 times -0.21 -0.19 -0.17 times 0.8 0.7 0.50 1.0 1.0 0.56 1.2 1.1 0.67 times times times CLRBY CLRMN CLRMM CLRSE FSC22 E_CAR_B E_CAR_R E_CAR_G a reference value Color MAX/CEN Color MAX/MIN 75 1.6 33 1 100 2.0 40 2 200 300 300 300 mVp-p mVp-p mVp-p 150 2.4 50 4 % times dB %/bit VIN1DC VIN1AC VIN2DC VIN2AC SVODC SVOAC 1.7 1.7 2.2 2.2 2.5 1 2.5 1 2 2 2.3 2.3 2.8 2.8 V Vp-p V Vp-p V Vp-p RBout0 Gout0 7 1.5 9 3.5 11 5.5 DB DB Gout15 1.8 Vp-p (min) (max) Vbias0 Vbias255 Vbiassns Vsbiassns RBout127 2.2 3.1 2.5 3.4 3.5 7 2.5 2.8 3.7 V V mV/Bit mV/Bit Vp-p BRT0 -30 -25 -20 IRE BRT63 BRT63H BRT127 1.9 3.1 20 2.2 3.4 25 2.5 3.7 30 V V IRE Symbol Conditions min Ratings typ max Unit
No.8047-5/44
LA76818A
Continued from preceding page.
Parameter Chroma block (NTSC) ACC amplitude characteristics 1 ACC amplitude characteristics 2 Demodulation output ratio R-Y/B-Y: NTSC Demodulation output ratio G-Y/B-Y: NTSC Demodulation angle B-Y/R-Y: NTSC Demodulation angle G-Y/B-Y: NTSC Demodulation angle switch G-Y/B-Y: NTSC Killer operating point 0 (NTSC) Killer operating point 3 (NTSC) Difference between two Killer operating points (NTSC) APC pull-in range (+) APC pull-in range (-) Tint center Tint variable range (+) Tint variable range (-) Cr Output amplitude Cb Output amplitude C-BPF1A (3.93MHz) C-BPF1B (4.73/4.13MHz) C-BPF1C (4.93/3.93MHz) C-BPF2A (3.93MHz) C-BPF2B (4.73/4.13MHz) C-BPF2C (4.93/3.93MHz) Deflection block Horizontal free-running frequency Horizontal pull-in range Horizontal output pulse width Horizontal output pulse saturation voltage Vertical free-running cycle 50 Vertical free-running cycle 60 Horizontal output pulse phase Horizontal output pulse phase Horizontal position adjustment range Horizontal position adjustment maximum variability width Horizontal blanking left @0 left @7 right @0 right @7 Sand castle pulse crest value H M1 M2 L BLKL0 BLKL7 BLKR0 BLKR7 SANDH SANDM1 SANDM2 SANDL BLKL: 000 BLKL: 111 BLKR: 000 BLKR: 111 7500 10800 1800 -1100 5.3 3.7 1.7 0.1 8300 11600 2600 -300 5.6 4.0 2.0 0.4 9100 12400 3400 500 5.9 4.3 2.3 0.7 ns ns ns ns V V V V HPHstep 350.0 ns VFR50 VFR60 HPHCENpal HPHCENnt HPHrange 5bit 312.0 262.0 9.5 9.5 312.5 262.5 10.5 10.5 2.4 313.0 263.0 11.5 11.5 H H s s s fH PULL Hduty V Hsat 400 36.1 0 37.6 0.2 39.1 0.4 Hz s V FH 15500 15670 15900 Hz PULIN+_N PULIN-_N TINCEN TINT+ TINTCBCR-R CBCR-B CBPF1A CBPF1B CBPF1C CBPF2A CBPF2B CBPF2C CbCr_IN DAC = 1 Cross B/W = 1 CbCr_IN DAC = 1 Cross B/W = 1 Reference: 4.43MHz FILTER SYS = 0010 Reference: 4.13MHz FILTER SYS = 0010 Reference: 3.93MHz FILTER SYS = 0010 Reference: 4.43MHz FILTER SYS = 0011 Reference: 4.13MHz FILTER SYS = 0011 Reference: 3.93MHz FILTER SYS = 0011 40 1.7 1.8 -5.0 -0.5 5.0 -5.0 -2.0 -2.5 -3.0 1.5 2.0 -3.0 0.0 0.0 3.4 3.7 -1.0 3.5 3.5 -1.0 2.0 2.5 -10 0 350 -350 10 -40 Hz Hz deg deg deg Vp-p Vp-p dB dB dB dB dB dB KILLN0 KILLN3 DKILLN 0dB = 40IRE 0dB = 40IRE KILLN0-KILLN3 -39 -40 0.5 -27 -28 6 dB dB dB ANGGC_N ANGGB_N ANGBR_N GB_N ACCM1_N ACCM2_N RB_N Input:+6dB/0dB 0dB = 40IRE Input:-20dB/0dB R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center R-Y/B-Y_GainBalance_DAC, R-Y/B-Y_Angle_DAC = Center G-Y Angle_DAC = 1 243 253 263 deg 227 237 247 deg 95 103 111 deg 0.22 0.27 0.38 times 0.8 0.7 0.80 1.0 1.0 0.90 1.2 1.1 1.00 times times times Symbol Conditions min Ratings typ max Unit
No.8047-6/44
LA76818A
Continued from preceding page. Parameter Burst gate pulse Width Phase Symbol BGPWD BGPPH Hstop Conditions min 2.5 4.9 3.30 Ratings typ 3.0 5.4 3.60 max 3.5 5.9 3.90 s s V Unit
Horizontal output stop voltage Vertical screen size adjustment Vertical output amplitude ramp PAL@64 NTSC@64 PAL@0 NTSC@0 PAL@127 NTSC@127
VSIZE: 1000000 VSIZE: 1000000 VSIZE: 0000000 VSIZE: 0000000 VSIZE: 1111111 VSIZE: 1111111
High-voltage dependent vertical size correction Vertical size correction @0 Vsizecomp VCOMP: 000 0.89 0.93 0.97 ratio
Vertical screen position adjustment Vertical ramp DC voltage PAL@32 NTSC@32 PAL@0 NTSC@0 PAL@63 NTSC@63 Vertical linearity @16 @0 @31 Vertical S-shaped correction @16 @0 @31 Vdcpal32 Vdcnt32 Vdcpal0 Vdcnt0 Vdcpal63 Vdcnt63 Vlin16 Vlin0 Vlin31 Vscor16 Vscor0 Vscor31 VDC: 100000 VDC: 100000 VDC: 000000 VDC: 000000 VDC: 111111 VDC: 111111 VLIN: 10000 VLIN: 00000 VLIN: 11111 VSC: 10000 VSC: 00000 VSC: 11111 2.25 2.25 1.85 1.85 2.65 2.65 0.85 1.17 0.57 0.75 1.08 0.49 2.40 2.40 2.00 2.00 2.80 2.80 1.00 1.32 0.72 0.90 1.23 0.64 2.55 2.55 2.15 2.15 2.95 2.95 1.15 1.47 0.87 1.05 1.38 0.79 Vdc Vdc Vdc Vdc Vdc Vdc ratio ratio ratio ratio ratio ratio
Package Dimensions
unit : mm 3273
47.58 54 28
(4.0)
1.05
3.8 5.0max
0.51min
1.78
0.48
(0.65)
SANYO : DIP54S(600mil)
0.25
27
15.24
13.8
No.8047-7/44
330 0.47F
0.01F
0.01F
METAL FILM
0.01F
1F
10F
680k
4.43
0.1F
0.01F 10k
1500pF
12k
0.01F
100F
0.47F
0.1F
54 A2C PLL CLMP CLMP VXO VIDEO SW SW APC1 EPF (ON/OFF) ACC DELAY LINE PEAKING CORING IF AGC SW VIF SYNC SEP BLACK STRETOH DC REST OSD CONTRAST BRIGHT BUS ABL CLAMP SPLL S.TRAP SW TRAP AFT VIDEO DET FM DET TRAP VIDEO AMP OVER MOD.
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
16pF
37
100pF
1F
36
35
34
33
32
31
30
29
4.7k
BPF
1H DELAY
HOR VCO
BPF
DC ADS.
1/256
LA76818A
LIM AMP
COLOR CLAMP
HOR C/D
VER SEP
VER C/D
PHASE SHIFTER
SW DC VOL RF AGC 2 3 4
0.01F
HOR VCC 15
0.01F
1%
0.47F 1k
0.47F
100k
0.1F
1 F
PAL:1% (NT:1%)
1 F
1 F
12k
10F
28
FBP
AFC2
HOR OUT 16 17 18 19 20 21 22 23
10k
+7.6V
10k
5
0.01F
0.01F
0.01F
0.01F
100F
10k 10F
0.01F
0.01F
100F
47k
100pF 100
0.1F 100
0.015F
39k
3k
50
47k
0.022F (M)
100pF
1k
1k
30k
1k
1k
10k
1F
100F
100
1k
1F
1500pF
DELAY (9US)
2k
+5V
24
25
26
27
1.5k
27
+7.6V
16k
16k
1k
16k
10k
NC
9V
LC4528B
10 12 13 17 18 19 20 21 22 23 14A 14B 15A 15B 16A 16B 11 1 2 3 4 5 8 9
24
25
+7.6V
16
15
14
13
12
11
10
2k 10k WIDTH(12US)
2200pF
NC
No.8047-8/44
35B 35A 34B 34A 32
75
75
44B 44A
54
52
46
45
43
42B 42A
40
39
37
36
31
30
29
100k
600
50
51
75
75
28
LA76818A
Test Conditions Ta = 25C, VCC = V8 = V31 = V43 = 5.0V, l18 = 19mA, ICC = l25 = 27mA
Circuit Voltage, Current
Parameter Horizontal supply voltage Symbol V25 Test point Input signal No signal Test method Apply a current of 27mA to pin 25 and measure the voltage at pin 25. No signal Apply a current of 19mA to pin 18 and measure the voltage at pin 18. No signal Apply a voltage of 5.0V to pin 8 and measure the incoming DC current [mA]. (IF AGC 2.5V applied) CCD supply current I31 No signal Apply a voltage of 5.0V to pin 31 and measure the incoming DC current [mA). No signal Apply a voltage of 5.0V to pin 43 and measure the incoming DC current [mA]. Initial Initial Initial Initial Bus conditions Initial
25
RGB supply voltage V18
18
IF supply current I8 (CDDICC)
31
Video/vertical supply current I43
43
SG2 CW
34.47MHz
SG3 CW
33.4MHz
SG4 CW
Frequency variable
SG5
SG6
SG7 50IRE
38.9MHz, 80dB 87.5% Video Mod. 50IRE Luma (Carrier: variable) 50IRE Luma
No.8047-9/44
LA76818A
5. Before measurement, adjust the DAC as follows.
Parameter Video Level DAC Test point SG6, 80dB Input signal Adjustment Set the output level at pin 46 as close to 2.0Vp-p as possible.
46
80dB SG1 Obtain the input level at which the DC voltage at pin 4 becomes 4.5V. Obtain the input level at which the DC voltage at pin 4 becomes 4.5V. Using an oscilloscope, observe the level at pin 46 and obtain the input level at which the waveform's p-p value becomes 1.4Vp-p. No signal Set IF AGC = 1 and measure the DC voltage at pin 46. SG1 Measure the DC voltage at pin 46. RF.AGC = "111111" RF.AGC = "000000"
46
No-signal video output voltage Sync signal tip level VOtip VOn
46
46
Video output amplitude Video S/N S/N VO
80dB SG6 Using an oscilloscope, observe the level at pin 46 and measure the waveforms p-p value. Measure the noise voltage at pin 46 with an RMS voltmeter through a 10kHz to 5.0MHz band-pass filter. Vsn 20Log (1.43/Vsn).
46
80dB SG1
46
80dB
IC-S
SG1
Input a 80dB SG1 signal and measure the DC voltage at pin 3. V3 Mix SG1 = 74dB, SG2 = 64dB, and SG3 = 64dB to enter the mixture in the VIF IN. Apply V3 to pin 3 from an external DC power supply. Using a spectrum analyzer, measure the difference between pin 46s 4.43MHz component and 1.07MHz component.
46
SG2 SG3
Differential gain
DG
SG5
46
Differential phase DP
80dB SG5 Using a vector scope, measure the level at pin 46.
46
Maximum AFT output voltage Minimum AFT output voltage AFT detection sensitivity VAFTS VAFTL VAFTH
80dB SG4 Set and input the SG4 frequency to 37.9MHz to be input. Measure the DC voltage at pin 10 at that moment. SG4 Set and input the SG4 frequency to 39.9MHz to be input. Measure the DC voltage at pin 10 at that moment. SG4 Adjust the SG4 frequency and measure frequency deviation f when the DC voltage at pin 10 changes from 1.5V to 3.5V. VAFTS = 2000/f [mV/kHz]
10
80dB
10
80dBz
10
80dBz
No.8047-10/44
LA76818A
Continued from preceding page.
Input signal APC pull-in range (U), (L) Symbol fPU, fPL Test point Input signal SG4 80dB Test method Connect an oscilloscope to pin 46 and adjust the SG4 frequency to a frequency higher than 38.9MHz to bring the PLL into unlocked mode. (A beat signal appears.) Lower the SG4 frequency and measure the frequency at which the PLL locks again. In the same manner, adjust the SG4 frequency to a lower frequency to bring the PLL into unlocked mode. Higher the SG4 frequency and measure the frequency at which the PLL locks again. NT Trap1 (4.5MHz), 2 (4.8MHz) BG Trap1 (5.5MHz), 2 (5.85MHz) I Trap1 (6.0MHz), 2 (6.55MHz) DK Trap1 (6.5MHz) NTR1 NTR2 BTR1 BTR2 ITR1 ITR2 DTR1 SG7 Determine the output level difference between carrier frequencies of 1Mhz, 4.5MHz and 4.8MHz. (Reference: 1MHz) SG7 Determine the output level difference between carrier frequencies of 1Mhz, 5.5MHz and 5.85MHz. (Reference: 1MHz) SG7 Determine the output level difference between carrier frequencies of 1MHz, 6.0MHz and 6.55MHz. (Reference: 1MHz) SG7 Determine the output level difference between carrier frequencies of 1MHz and 6.5MHz. (Reference: 1MHz) SIF.SYS = 11 SIF.SYS = 10 SIF.SYS = 01 SIF.SYS = 00 Bus conditions
46
46
46
46
46
2
SLS
2
SF
STHD
2
SAMR
SIF.S/N
SSN
2
PAL de-emph time constant SPTC
90dB, CW 90dB, fm = 3.18kHz FM = 30kHz fo = 4.5MHz 90dB, fm = 400Hz FM = 15kHz fo = 4.5MHz 90dB, fm = 2.12kHz FM = 15kHz
SGD
SNTC
No.8047-11/44
LA76818A
Audio Block Input Signals and Test Conditions
Unless otherwise specified, the following conditions apply when each measurement is made. 1. Bus control condition: AUDIO.MUTE = "0", A.MONI.SW = "0", AUDIO.SW = "1", VOL.FIL = "0", SIF.SYS = "01", IF.AGC.SW = "1" 2. Input 5.5MHz, 90dB and CW at pin 54. 3. Enter an input signal from pin 51.
Input signal Maximum gain Symbol AGMAX Test point Input signal 1kHz, CW Test method Measure the 1kHz component at the pin 1. V1 [mVrms] AGMAX = 20*Log (V1/500) [dB] Variable range ARANGE 1kHz, CW Measure the 1kHz component the pin 1. V2 [mVrms] ARANGE = 20*Log (V1/V2) [dB] Frequency characteristics Mute AMUTE AF 20kHz, CW Measure the 20kHz component at the pin 1. V3 [mVrms] AF = 20*Log (V3/V1) [dB] 20kHz, CW Measure the 20kHz component at the pin 1. V4 [mVrms] AMUTE = 20*Log (V3/V4) [dB] Distortion ATHD 1kHz, CW Measure the distortion of the 1kHz component at the pin 1. Measure the noise level (DIN AUDIO) at the pin 1. V5 [mVrms] ASN = 20*Log (V1/V5) [dB] Crosstalk ACT 1kHz, CW Measure the 1kHz component at the pin 1. V6 [mVrms] ACT = 20*Log (V1/V6) [dB] VOLUME = "1111111" AUDIO.SW = "0" VOLUME = "1111111" AUDIO.MUTE = 1 VOLUME = "1111111" VOLUME = "1111111" VOLUME = "1111111" VOLUME = "0000000" Bus conditions VOLUME = "1111111"
500mVrms
500mVrms
500mVrms
500mVrms
1
S/N ASN
500mVrms No signal
500mVrms
No.8047-12/44
LA76818A
Video Block Input Signals and Test Conditions
C IN Input* chroma burst signal: 40 IRE Y IN input signal 100IRE: 714mV Bus control bit conditions: Initial test state 0IRE signal (L-0): NTSC standard sync signal
PEDESTAL LEVEL H SYNC 4.7s (H/V SYNC:40IRE: 286mV)
CW signal (L-CW)
20IRE CW signal
50IRE
100IRE
5s (Point A)
No.8047-13/44
LA76818A
R/G/B IN Input signal
RGB Input signal 1 (0-1)
to each 20s
0.35V A B
0.7V 0.0VDC
20s
30s
1.0VDC 0.0VDC
No.8047-14/44
LA76818A
Video Block Test Conditions
Input signal Video overall gain (Contrast max) Contrast adjustment characteri stics Min/max CONT0 L-50 Normal/ max CONT63 Symbol CONT127 Test point Input signal L-50 CNTHB [Vp-p] CONT127 = 20Log (CNTHB/0.357). L-50 Measure the output signals 50IRE amplitude. CNTCB [Vp-p] CONT63 = 20Log (CNTCB/0.357). Measure the output signals 50IRE amplitude. CNTLB [Vp-p] CONT0 = 20Log (CNTLB/0.357). Video frequency Characteri stics NTSC BW1 L-CW With the input signals continuous wave = 100kHz, measure the output signals continuous wave amplitude. PEAKDC [Vp-p] With the input signals continuous wave = 1.8MHz, measure the output signals continuous wave amplitude. CW1.8 [Vp-p] BW1 = 20Log (CW1.8/PEAKDC). PAL BW2 With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. CW2.2 [Vp-p] BW2 = 20Log (CW2.2/PEAKDC). 6MHz TRAP BW3 With the input signals continuous wave = 2.3MHz, measure the output signals continuous wave amplitude. CW2.3 [Vp-p] BW3 = 20Log (CW2.3/PEAKDC). APF BW4 With the input signals continuous wave = 3.4MHz, measure the output signals continuous wave amplitude. CW3.4 [Vp-p] BW3 = 20Log (CW3.4/PEAKDC). Chroma trap amount PAL CtraPP L-CW With the input signals continuous wave = 4.43MHz, measure the output signals continuous wave amplitude. F0P [Vp-p] CtraP = 20Log (F0P/PEAKDC). NTSC CtraPN With the input signals continuous wave = 3.58MHz, measure the output signals continuous wave amplitude. F0N [Vp-p] CtraN = 20Log (F0N/PEAKDC). DC transmissi on amount L-100 Measure the output signals 0IRE DC level (DRVPH V) and 100IRE amplitude (DRVH Vp-p). ClampG = 100 (1+(DRVPH - BRTPL)/DRVH). (PIN45: 3V) 1 ClampG1 L-0 Measure the output signals 0IRE DC level. BRTPL [V] Brightness: 0000000 CONTRAST: 1111111 Brightness: 0000000 Contrast: 1111111 DCREST=00 BLK.ST.DEF=1 WPL=0 2 ClampG2 L-100 With DCREST = 01, carry out measurement similarly to the case of the DC transmission amount 1. (PIN45: 3V) 3 ClampG3 With DCREST = 10, carry out measurement similarly to the case of the DC transmission amount 1. (PIN45: 3V) 4 ClampG4 With DCREST = 11, carry out measurement similarly to the case of the DC transmission amount 1. (PIN45: 3V) Measure the output signals 0IRE DC level (DRVPH V) and 100IRE amplitude (DRVH Vp-p) and calculate ClampG = 100 (1+(DRVPH BRTPL)/DRVH). Brightness: 0000000 Contrast: 1111111 DC.rest. = 11 DC.rest. = 10 DC.rest. = 01 FILTER SYS: 000 Sharpness: 000000 FILTER SYS: 0000 SHARPNESS: 000000 Y APF: 1 FILTER SYS: 010 Sharpness: 000000 FILTER SYS: 0100 SHARPNESS: 000000 FILTER SYS: 0010 SHARPNESS: 000000 FILTER SYS: 0000 SHARPNESS: 000000 CONTRAST: 0000000 CONTRAST: 0111111 Test method Measure the output signals 50IRE amplitude. Bus conditions CONTRAST: 1111111
21
21
21
21
21
21
No.8047-15/44
LA76818A
Continued from preceding page.
Input signal Y-DL TIME PAL TdY2 NTSC Symbol TdY1 Test point Input signal L-50 Test method Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude. Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude. SECAM TdY3 Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude. 6MHz TRAP APF TdY5 TdY4 Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude. Obtain the time difference (the delay time) from when the rise of the input signal's 50IRE amplitude to the output signal's 50IRE amplitude. Black stretch gain MAX BKSTmax L-BK Measure the 0IRE DC level at point A of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST1 [V] Measure the 0IRE DC level at point A of the output signal in the Black Stretch ON mode. (PIN45: 3V) BKST2 [V] BKSTmax = 50 (BKST1-BKST2)/ CNTHB MID BKSTmid With Blk.str.gain = 01, carry out the same measurement as for the case of black stretch gain (MAX). (PIN45: 3V) MIN BKSTmin With Blk.str.gain = 00, carry out the same measurement as for the case of black stretch gain (max). (PIN45: 3V) Black stretch start max (60IRE Black) BKSTTHmax L-60 Measure the DC level at 60IRE of the output signal in the Black Stretch ON mode. (PIN45: 3V) BKST3 [V] Measure the 60IRE DC level of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST4 [V] Calculate BKSTTHmax = 50 (BKST4-BKST3)/ CNTHB. Black stretch start mid (50IRE Black) BKSTTHmid L-50 Measure the 50IRE DC level of the output signal in the Black Stretch Defeat ON mode. (PIN45: 3V) BKST5 [V] Measure the 50IRE DC level of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST6 [V] Calculate BKSTTHmid = 50 (BKST6-BKST5)/ CNTHB. Black stretch start min (40IRE Black) BKSTTHmin L-40 Measure the 40IRE DC level of the output signal in the Black Stretch Defeat ON mode. (PIN45: 3V) BKST7 [V] Measure the 40IRE DC level of the output signal in the Black Stretch Defeat (Black Stretch OFF) mode. BKST8 [V] Calculate BKSTTHmin = 50 (BKST8-BKST7)/ CNTHB. Blk.str.gain = 01 Blk.str.start = 00 Blk.str.gain = 01 Blk.str.start = 01 Blk.str.gain = 01 Blk.str.start = 10 Blk.str.gain = 00 Blk.str.start = 01 Blk.str.gain = 01 Blk.str.start = 01 Blk.str.gain = 10 Blk.str.start = 01 FILTER SYS: 0000 Y APF: 1 FILTER SYS: 0100 FILTER SYS: 1000 FILTER SYS: 0010 Bus conditions FILTER SYS: 0100
21
21
21
21
21
No.8047-16/44
LA76818A
Continued from preceding page.
Input signal Sharpness variability range NTSC Symbol Sharp32T1 Test point Input signal L-CW Test method With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. F01S32 [Vp-p] Sharp32T1 = 20Log (F01S32/PEAKDC) Max Sharp63T1 With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. F01S63 [Vp-p] Sharp63T1 = 20Log (F01S63/PEAKDC) Min Sharp0T1 With the input signals continuous wave = 2.2MHz, measure the output signals continuous wave amplitude. F01S0 [Vp-p] Sharp0T1 = 20Log (F01S0/PEAKDC). Sharpness variable range PAL Sharp32T2 L-CW With the input signals continuous wave = 2.7MHz, measure the output signals continuous wave amplitude. F02S32 [Vp-p] Sharp32T3 = 20Log (F02S32/PEAKDC) Max Sharp63T2 With the input signals continuous wave = 3MHz, measure the output signals continuous wave amplitude. F02S63 [Vp-p] Sharp63T2 = 20Log (F02S63/PEAKDC) Min Sharp0T2 With the input signals continuous wave = 3MHz, measure the output signals continuous wave amplitude. F02S0 [Vp-p] Sharp0T2 = 20Log (F02S0/PEAKDC) Sharpnes s variable range SECAM Sharp32T3 L-CW With the input signals continuous wave = 2.3MHz, measure the output signals continuous wave amplitude. F03S32 [Vp-p] Sharp32T3 = 20Log (F03S32/PEAKDC) Max Sharp63T3 With the input signals continuous wave=2.3MHz, measure the output signals continuous wave amplitude. F03S63 [Vp-p] Sharp63T3 = 20Log (F03S63/PEAKDC) Min Sharp0T3 With the input signals continuous wave = 2.3MHz, measure the output signals continuous wave amplitude. F01S0 [Vp-p] Sharp0T3 = 20Log (F03S0/PEAKDC) Sharpness variable range 6MHz TRAP Sharp32T4 L-CW With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F04S32 [Vp-p] Sharp32T4 = 20Log (F04S32/PEAKDC) Max Sharp63T4 With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F04S63 [Vp-p] Sharp63T2 = 20Log (F02S63/PEAKDC) Min Sharp0T4 With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F04S0 [Vp-p] Sharp0T4 = 20Log (F04S0/PEAKDC) Filter Sys: 0010 Sharpness: 000000 Filter Sys: 0010 Sharpness: 111111 Filter Sys:0010 Sharpness: 100000 FILTER SYS: 1000 Sharpness: 000000 FILTER SYS: 1000 Sharpness: 111111 FILTER SYS: 1000 Sharpness: 100000 Filter Sys: 0010 Sharpness: 000000 Filter Sys: 0010 Sharpness: 111111 Filter Sys: 0010 Sharpness: 100000 FILTER SYS: 0000 Sharpness: 000000 FILTER SYS:0000 Sharpness: 111111 Bus conditions FILTER SYS: 0000 Sharpness: 100000
21
21
21
21
No.8047-17/44
LA76818A
Continued from preceding page.
Input signal Sharpnes s variable range APF Symbol Sharp32T5 Test point Input signal L-CW Test method With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F05S32 [Vp-p] Sharp32T5 = 20Log (F05S32/PEAKDC) Max Sharp63T5 With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F05S63 [Vp-p] Sharp63T5 = 20Log (F05S63/PEAKDC) Min Sharp0T5 With the input signals continuous wave = 3.0MHz, measure the output signals continuous wave amplitude. F05S0 [Vp-p] Sharp0T5 = 20Log (F05S0/PEAKDC). White peak limiter operating point 2 WPL2 1 WPL1 L-100 Set WPL to 00, apply a 3.0 V level to pin 13, and measure the output amplitude (pedestal to white). Gradually increase the input signal amplitude and measure the output amplitude (pedestal to white) when the output clips (WP1). WPL1=WP1/CNTCB1*100 Set WPL to 01, gradually increase the input signal amplitude and measure the output amplitude (pedestal to white) when the output clips (WP2). WPL2=WP2/CNTCB1*100 3 WPL3 Set WPL to 10, gradually increase the input signal amplitude and measure the output amplitude (pedestal to white) when the output clips (WP3). WPL3=WP3/CNTCB1*100 4 WPL4 Set WPL to 10, gradually increase the input signal amplitude and measure the output amplitude (pedestal to white) when the output clips (WP4). WPL4=WP4/CNTCB1*100 Y gamma effective point 1 YG1 L-100 Measure the output amplitude (0 to 100 IR) when Y GAMMA is 0. After that, set Y GAMMA to 1 and measure the output amplitude (0 to 100 IR). This is GAM1. Calculate YG1 with the formula YG1 = GAM1/GAM0 * 100. 2 YG2 Measure the output amplitude (0 to 100 IR) when Y GAMMA = 2 Y GAMMA = 1 WPL = 10 WPL = 10 WPL = 01 WPL = 00 FILTER SYS: 1000 Sharpness: 000000 Y APF:1 FILTER SYS: 0000 Sharpness: 111111 Y APF: 1 Bus conditions FILTER SYS: 0000 Sharpness: 100000 Y APF: 1
21
21
21
21
Y GAMMA is 0. After that, set Y GAMMA to 2 and measure the output amplitude (0 to 100 IR). This is GAM2. Calculate YG1 with the formula YG2 = GAM2/GAM0 * 100.
YG3
Y GAMMA = 3
21
Y GAMMA is 0. After that, set Y GAMMA to 3 and measure the output amplitude (0 to 100 IR). This is GAM3. Calculate YG3 with the formula YG3 = GAM3/GAM0 * 100.
GRAY
21
Horizontal/vertical blanking output level Pre-shoot adjust1 PreShoot1 L-100 RGBBLK L-100
pin21, and transfer IRE. Measure the DC level (RGBBLK V) for the output signals blanking period. Measure the pre-shoot width (Tpre) and over-shoot width (Tover) at rise of 100IRE amplitude of the output signal. PreShoot = Tpre/Tover.
21
Pre-shoot adj. = 00 Filter Sys: 000 Sharpness = 111111 Pre-shoot adj. = 11 Filter Sys: 000 Sharpness = 111111 Over-shoot adj. = 11 Filter Sys: 000 Sharpness = 111111
21
Pre-shoot adjust2
PreShoot2
L-100
With Pre-shoot adj. = 11, carry out the same measurement as for the case of Pre-Shoot 1.
21
Over-shoot adjust OverShoot L-100
With Over-shoot adj. = 11 Measure the pre-shoot width (Tpre) and over-shoot width (Tover) at rise of 100IRE amplitude of the output signal. OverShoot = Tover/Tpre.
21
No.8047-18/44
LA76818A
OSD Block Test Conditions
When measuring the OSD block, set the bus bit to 63(0111111) for Contrast, 63(0111111) for Brightness.
Input signal OSD Fast SW threshold Red RGB output level ROSDC Symbol FSTH Test point Input signal L-0 O-2 L-50 Test method Apply voltage to pin 17 and measure the voltage at pin 17 at the point where the output signal switches to the OSD signal. Measure the output signals 50IRE amplitude. CNTCR [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHR [Vp-p] Pin 17: 3.5V Pin 14A: O-2 applied ROSDC = 50 (OSDHR /CNTCR) Green RGB output level GOSDC L-50 Measure the output signals 50IRE amplitude. CNTCG [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHG [Vp-p] Pin 17: 3.5V Pin 15A: O-2 applied GOSDC = 50 (OSDHG /CNTCG) Blue RGB output level BOSDC L-50 Measure the output signals 50IRE amplitude. CNTCB [Vp-p] L-0 O-2 Measure the OSD output amplitude. OSDHB [Vp-p] BOSDC = 50 (OSDHB/CNTCB) Analog OSD R output level L-0 Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLR Vp-p and RGBHR Vp-p, respectively. Gain match linearity Analog OSD G output level RRGB LRRGB L-0 RRGB = RGBLR/CNTCR. LRRGB = 100 (RGBLR/RGBHR). Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLG Vp-p and RGBHG Vp-p, respectively. Gain match linearity Analog OSD B output level GRGB LGRGB L-0 GRGB = RGBLG/CNTCG. LGRGB = 100 (RGBLG/RGBHG). Measure the amplitudes at point A (0.35V portion of the input signal 0-1) and point B (0.7V portion of the input signal 0-1) of the output signal. Assign the measured values to RGBLB Vp-p and RGBHB Vp-p, respectively. Gain match linearity BRGB LBRGB BRGB = RGBLB/CNTCB. LBRGB = 100 (RGBLB/RGBHB). Pin 17: 3.5V Pin 16A: O-1 applied Pin 17: 3.5V Pin 15A: O-1 applied Pin 17: 3.5V Pin 16A: O-2 applied Pin 17: 3.5V Pin 14A: O-1 applied Bus conditions Pin 16A: O-2 applied
21
19
20
21
19
O-1
20
O-1
21
O-1
No.8047-19/44
LA76818A
RGB Output Block [Cutoff, Drive Block] Test Conditions When measuring the RGB block, set the bus bit to 127(01111111) for Contrast.
Input signal Brightnes s control Normal Symbol BRT63 Test point Input signal L-0 Test method Bus conditions Measure the 0IRE DC levels of the respective output Brightness: signals of R output (19), G output (20), and B output 01111111 (21). Assign the measured values to BRTPCR, BRTPCG, and BRTPCB V, respectively.
19
20
BRT63 = (BRTPCR+BRTPCG+BRTPCB)/3
21
normal-H BRT63H Measure the 0IRE DC level of the output signal of Brightness: 0111111 B Bias: 11111111 Sub Bias: 1111111 Brightness: 1111111 B Bias: 11111111 Sub Bias: 1111111
21
Max BRT127
B output (21) and assign the measured value to BRTPCBH. Measure the 0IRE DC level of the output signal of B output (21) and assign the measured value to BRTPHB. BRT127 = 50 (BRTPHB-BRTPCB)/CNTHB
Min
BRT0
Measure the 0IRE DC level of the output signal of B output (21) and assign the measured value to BRTPLB. BRT0 = 50 (BRTPLB-BRTPCBH)/CNTHB
Min
Vbias0
L-50
Measure the 0IRE DC levels (Vbias0* V) of the respective output signals of R output (19), G output (20), and B output (21). *: R, G, and B
Sub-Brightness: 1111111
19
Max
Vbias255
20
Measure the 0IRE DC levels (Vbias255* V) of the respective output signals of R output (19), G output (20), and B output (21). *: R, G, and B Measure the 0IRE DC levels (BAS80* V) of the respective output signals of R output (19), G output (20), and B output (21). *: R, G, and B Measure the 0IRE DC levels (BAS48* V) of the respective output signals of R output (19), G output (20), and B output (21). Vbiassns* = (BAS80*-BAS48*)/32
Sub-Brightness: 1111111 Red/Green/Blue Bias: 11111111 Red/Green/Blue Bias:01010000 Sub Bias: 1111111 Red/Green/Blue Bias: 00110000 Sub Bias: 1111111
21
resolution Vbiassns
Vsbiassns
L-50
Measure the 0IRE DC levels (SBTPM* V) of the respective output signals of R output (19), G output (20), and B output (21). Vsbiassns* = (BRTPC*-SBTPM*)
19
20
No.8047-20/44
LA76818A
Continued from preceding page.
Input signal Drive adjustment maximum output Symbol RBout127 Gout15 Test point Input signal L-100 Test method Measure the 100IRE amplitudes of the respective output signals of R output (19) and B output (21). DRVH* [Vp-p] *: R and B Bus conditions Brightness: 0000000
19
20
Measure the 100IRE amplitude of the output signal of G output (20) and assign the measured value to DRVH* [Vp-p]. *: G L-100 Measure the 100IRE amplitudes of the respective output signals of R output (19), G output (20), and B output (21). DRVL* [Vp-p] *: R and B Brightness: 0000000 Red/Blue Drive: 0000000 Green Drive: 0000
21
Output attenuation
RBout0 Gout0
19
20
Measure the 100IRE amplitude of the output signal of G output (20) and assign the measured value to DRVL* [Vp-p]. *: G RBout0* = 20Log (DRVH*/DRVL*) Gout0* = 20Log (DRVH*/DRVL*)
21
42
42
L-100 Input signals to pin 44 and measure the voltage of the pedestal. Pin 44 recommended input level VIDEO SW: 0
44
44
L-100 Input signals to pin 42 and measure the voltage of the pedestal at pin 40. L-100 Input signals to pin 42 and measure the voltage of the pedestal at pin 40. VIDE0 SW: 1 VIDEO SW: 1
40
40
No.8047-21/44
LA76818A
Chroma Block Input Signals and Test Conditions
Unless otherwise specified, the following conditions apply when each measurement is made. 1. VIF, SIF blocks: No signal 2. Deflection Block: Horizontal/vertical composite sync signals are input and the deflection block must be locked into the sync signals (Refer to the Deflection Block Input Signals and the Test Conditions). 3. Bus control conditions: Set the following conditions unless otherwise specified. Y Input is 42 Pin (EXT-V IN), C Input is 44 Pin (S-C IN) (Video SW=1, C.Ext=1) Other DAC except the above-mentioned conditions is all initial conditions. 4. Y Input condition: No signal unless otherwise specified. (Sync is necessary to obtain synchronization). 5. How to calculate the demodulation ratio and angle: R-Y axis 90 B-Y axis angle = tan-1(B(0)/B(270))+270 R-Y axis angle = tan-1(R(180)/R( 90))+90 G-Y axis angle = tan-1(G(270)/G(180))+180
R(90) R(180)
180
G(180) G(270)
B(270) B(0)
0
B-Y axis
B-Y axis amplitude Vb = SQRT(B(0)*B(0)+B(270)*B(270)) G-Y axis R-Y axis amplitude Vr = SQRT(R(180)*R(180)+R(90)*R(90)) G-Y axis amplitude Vg = SQRT(G(180)*G(180)+G(270)*G(270))
270
No.8047-22/44
LA76818A
6. Chroma input signal: As for the PAL signal, the burst swings such as 135 and 225 every horizontal period. Chroma describes the phase caused when the burst occurs at 135. As for the NTSC signal, the burst occurs constantly at 180. The figures below are based on the phase of NTSC. When a PAL signal is generated, adjust the phase and then enter signals. The item common to both PAL and NTSC is the PAL signal. For those other than this, the measurement must be performed for each individual signals. The condition of fsc: Set the following conditions unless otherwise specified. PAL = 4.433619MHz NTSC = 3.579545MHz C-1 40IRE Burst 0 90 180 270 fsc
40IRE
62.5IRE
Burst C-3
fsc 346
40IRE fsc CW (Note: fscN*fh when the frequency is specified. N should be a natural number and the nearest value should be used.) C-4 Burst C-5 Burst C-6 0.35V 0.35V * There is no signal for H, V blanking period. R-Y only B-Y only Burst
No.8047-23/44
LA76818A
Chroma Block [PAL/NTSC Common] Test Conditions
Input signal B-Y/Y amplitude ratio Symbol CLRBY Test point Bout Input signal YIN:L77 No signal V1 Input a signal to the CIN (only sync signal to the YIN) and measure the output level. CLRBY = 100 (V2/V1)+15% Color control characteris tics 2 CLRMM 1 CLRMN C-1 Measure the output amplitude V1 at color control MAX mode and output amplitude V2 at color control CEN mode. CLRMN = V1/V2 Measure the output amplitude V3 at color control MIN mode. V3 CLRMM = 20Log (V1/V3) Color control sensitivity CLRSE C-1 Measure the output amplitude V4 at color control 90 mode and output amplitude V5 at color control 38 mode. CLRSE = 100 (V4-V5)/(V2 52) Residual higher harmonic level R E_CAR_R Rout Measure the 8.86MHz component output amplitude at pin 19. B E_CAR_B C-1 Measure the 8.86MHz component output amplitude at pin 21. Color: 1011010 Color: 0100110 Color: 0000000 Color: 1111111 Color: 1000000 Color: 1000000 Test method Measure the Y systems output level. Bus conditions
21
C-2
21
21
21
Burst only
19
G E_CAR_G Gout Measure the 8.86MHz component output amplitude at pin 20.
20
21
+6dB
21
19
Demodulation output ratio G-Y/B-Y: PAL GB_P C-4 Measure Bout output amplitude Vbp and GOUT output amplitude Vgbp. GB_P = Vgbp/Vbp. Color: 1000000
21
20
Demodulation output ratio G-Y/R-Y: PAL GR_P C-5 Measure Rout output amplitude Vrp and GOUT output amplitude Vgbp. GR_P = Vgrp/Vbp. Color: 1000000
20
No.8047-24/44
LA76818A
Continued from preceding page.
Input signal Demodulation angle R-Y/B-Y: PAL Symbol ANGBR_P Test point Input signal C-1 Test method Refer to 5. and measure the B-Y and R-Y demodulation angle and calculate. Bus conditions Color: 1000000
21
19
Killer operating point 0 (PAL) Killer operating point 3 (PAL) Difference between two Killer operating points (PAL) APC pull-in range (+) PULIN+_P C-1 Decrease the chroma fsc frequency from 4.433619MHz+1000Hz and measure the frequency at which the VCO locks. APC pull-in range (-) PULIN-_P C-1 Increase the chroma fsc frequency from 4.433619MHz-1000Hz and measure the frequency at which the VCO locks. DKILLP KILLP3 KILLP0 C-1 Reduce the input signal until the output Level becomes 150mVp-p or less. Measure the input level at that moment. C-1 Reduce the input signal until the output Level becomes 150mVp-p or less. Measure the input level at that moment. DKILLP = KILLPO-KILLP3 Color Killer Ope.: 3 Color Killer Ope.: 0
21
21
21
21
21
+6dB
21
19
Demodulation output ratio G-Y/B-Y: NTSC Demodulation angle B-Y/R-Y: NTSC ANGBR_N C-1 Refer to 5. and measure the B-Y and R-Y demodulation angle and calculate. Reference: B-Y angle Color: 1000000 GB_N C-1 Refer to 5. and measure GOUT output amplitude Vg. And calculate GB_N = Vg/Vb. Color: 1000000
20
21
19
Demodulation angle G-Y/B-Y: NTSC ANGGB_N C-1 Refer to 5. and measure the B-Y and G-Y demodulation angle and calculate. Reference: B-Y angle Color: 1000000
21
20
Killer operating point 0 (NTSC) Killer operating point 3 (NTSC) KILLN3 KILLN0 C-1 Reduce the input signal until the output level becomes 150mVp-p or less. Measure the input level at that moment. C-1 Reduce the input signal until the output level becomes 150mVp-p or less. Measure the input level at that moment. Color Killer Ope.: 3 Color Killer Ope.: 0
21
21
No.8047-25/44
LA76818A
Continued from preceding page.
Input signal Difference between two Killer operating points (NTSC) APC pull-in range (+) PULIN+_N C-1 Decrease the chroma fsc frequency from 3.579545MHz+1000Hz and measure the frequency at which the VCO locks. APC pull-in range (-) PULIN-_N C-1 Increase the chroma fsc frequency from 3.579545MHz-1000Hz and measure the frequency at which the VCO locks. Tint center TINCEN C-1 Measure each part of the output level and calculate the B-Y axis angle. C-1 Measure each part of the output level and calculate the B-Y axis angle. TINT+ = B-Y axis angle -TINCEN Tint variable range (-) TINTC-1 Measure each part of the output level and calculate the B-Y axis angle. TINT- = B-Y axis angle -TINCEN Cr output amplitude CBCR-R R-Y IN: C-6 Measure the output amplitude. (*B-Y IN: no signal) B-Y IN: C-6 Measure the output amplitude. (*R-Y IN: no signal) CbCr IN: 1 Color System: 101 Cross B/W: 01 Cb output amplitude CBCR-B CbCr IN: 1 Color System: 101 Cross B/W: 01 TINT: 0000000 TINT: 1111111 TINT: 1000000 Symbol DKILLN Test point Input signal Test method DKILLN = KILLNO-KILLN3 Bus conditions
21
21
21
21
Tint variable range (+) TINT+
21
21
19
21
21
21
PAL signal
21
PAL signal
21
PAL signal
21
PAL signal
21
PAL signal
No.8047-26/44
LA76818A
Deflection Block Input Signals and Test Conditions
Unless otherwise specified, the following conditions apply when each measurement is made. 1. VIF, SIF blocks: No signal 2. C input: No. signal 3. Sync input: A horizontal/vertical composite sync signal PAL: 43IRE, horizontal sync signal (15.625kHz) and vertical sync signal (50kHz) NTSC: 40IRE, horizontal sync signal (15.734264kHz) and vertical sync signal (59.94kHz) Note: No burst signal, chroma signal shall exist below the pedestal level. Signal unsuitable for Y input
4. Bus control conditions: Initial conditions unless otherwise specified. 5. The delay time from the rise of the horizontal output (pin 27 output) to the fall of the FBP IN (pin 28 input) is 9s. 6. Pin 13 (vertical size correction circuit input terminal) is connected to VCC (5.0V).
No.8047-27/44
LA76818A
Deflection Block Test Conditions
Input signal Horizontal free-running frequency Horizontal pull-in range fH PULL Symbol fH Test point Input signal Y IN: No signal YIN: Test method Connect a frequency counter to the output of pin 27 (H out) and measure the horizontal free-running frequency. Using an oscilloscope, monitor the horizontal sync signal which is input to the Y IN (pin 42) and the pin 27 output (H out) and vary the horizontal signal frequency to measure the pull-in range. Measure the voltage for the pin 27 horizontal output pulses low-level period. Bus conditions
27
42
Hduty
Y IN:
27
V Hsat
Y IN:
Measure the voltage for the pin 27 horizontal output pulses low-level period.
27
50 (PAL)
VFR50 VFR60
Y IN:
Measure the vertical output period T at pin 23 T15.625kHz (PAL) T15.734kHz (NTSC)
23
No signal
60 (NTSC)
PAL
Y IN:
Measure the delay time from to the rise of the pin 27 horizontal output pulse to the fall of the Y IN horizontal sync signal.
27
42
NTSC)
PAL NTSC
HPHCEN
20IRE
27
42
PAL
Measuring HPHCEN
20IRE
No.8047-28/44
LA76818A
Continued from preceding page.
Input signal Horizontal position adjustment maximum variable width Symbol HPHstep Test point Input signal Y IN: Horizontal/ vertical sync signal Test method With H PHASE: 0 to 31 varied, measure the delay time from to the rise of the pin 27 horizontal output pulse to the fall of the Y IN horizontal sync signal and calculate the variation at each step. Retrieve data for maximum variation. to H PHASE: 11111 Bus conditions H PHASE: 00000
27
42
PAL
Measuring HPHCEN
20IRE
Horizontal output
@0
BLKL0
Y IN:
Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKL = 000.
BLKL: 000
27
42
PAL
Y IN
Hsync
Blue OUT
@7
BLKL7
Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKL = 111.
BLKL: 111
Y IN
Hsync
Blue OUT
No.8047-29/44
LA76818A
Continued from preceding page.
Input signal Horizontal blanking right variable range @0 Symbol BLKR0 Test point Input signal Y IN: Test method Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKR = 000. Bus conditions BLKR: 000
21
Y IN
Hsync
42
PAL
Blue OUT
@7
BLKR7
Measure the time T from the left end of Hsync at pin 42 Y IN to the left end of blanking at pin 21 BlueOUT with BLKR = 111.
BLKR: 111
SANDH
Y IN:
Measure the supply voltage at point H of the pin 28 FBP IN wave form for Hsync period.
28
M1
SANDM1
Measure the supply voltage at point M1 of the pin 28 FBP IN wave form for Hsync period.
M1
SANDL
Measure the supply voltage at point L of the pin 28 FBP IN wave form for Hsync period.
M2
SANDM2
Measure the supply voltage at point M2 of the pin 28 FBP IN wave form for Vsync period.
BGPWD
Y IN:
Measure the BGP width T of the pin 28 FBP IN wave form for Hsync period.
28
No.8047-30/44
LA76818A
Continued from preceding page.
Input signal Burst gate pulse I phase Symbol BGPPH Test point Input signal Y IN: Test method Measure the time from the left end of Hsync at pin 42 Y IN to the left end of the pin 28 FBP IN wave form for Hsync period. Bus conditions
28
Hsync Y IN
42
PAL
FB PIN
Hstop
Y IN:
Decrease the current from a source connected to pin 25 and measure the pin 25 voltage at which HOUT stops.
25
47
23
PAL@0
Vspal0 Vsnt0
Y IN:
Monitor the pin 23 vertical ramp output and measure the voltage at line 24 (22: NTSC) and line 310 (262: NTSC). Vspal0 = Vline310-Vline24 Vsnt0 = Vline262-Vline22 Vertical ramp output
VSIZE: 0000000
23
NTSC@0
PAL@127
Vspal127 Vsnt127
Y IN:
Monitor the pin 23 vertical ramp output and measure the voltage at line 24 (22: NTSC) and line 310 (262: NTSC). Vspal27 = Vline310-Vline24 Vsnt127 = Vline262-Vline22 Vertical ramp output
VSIZE: 1111111
23
NTSC@127
No.8047-31/44
LA76818A
High-voltage dependent vertical size correction
Input signal Vertical size correction@0 Symbol Vsizecomp Test point Input signal Y IN: Horizontal/ vertical sync signal PAL Test method Monitor the pin 23 vertical ramp output and measure the voltage at the line 24 and line 310 with VCOMP = 000. Va = Vline310-Vline24 Apply 4.1V to pin 13 and measure the voltage at the line 24 and line 310 again. Calculate as follows: Va = Vline310-Vline24 Vsizecomp = Vb/Va Vertical ramp output Bus conditions VCOMP: 000
23
23
Line 167
PAL@0
Vdcpal0 Vdcnt0
Y IN:
Monitor the pin 23 vertical ramp output and measure the voltage at line 167. (PAL) Monitor the pin 23 vertical ramp output and measure the voltage at line 142. (NTSC) Vertical ramp output
VDC: 000000
23
NTSC@0
Line 167
PAL@63
Vdcpal63 Vdcnt63
Y IN:
Monitor the pin 23 vertical ramp output and measure the voltage at line 167. (PAL) Monitor the pin 23 vertical ramp output and measure the voltage at line 142. (NTSC) Vertical ramp output
VDC: 111111
23
NTSC@63
Line 167
No.8047-32/44
LA76818A
Continued from preceding page.
Input signal Vertical linearity @16 Symbol Vlin16 Test point Input signal Y IN: Horizontal/ vertical sync signal PAL Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 24, line 167 and 310. Assign the respective measured values to Va, Vb and Vc. Vlin16 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 310 Bus conditions
23
Line 167 Line 24 @0 Vlin0 Monitor the pin 23 vertical ramp output and measure the voltage at line 24, line 167 and 310. Assign the respective measured values to Va, Vb and Vc. Vlin0 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 310 VLIN: 00000
@31
Vlin31
Monitor the pin 23 vertical ramp output and measure the voltage at line 24, line 167 and 310. Assign the respective measured values to Va, Vb and Vc. Vlin31 = (Vb-Va)/(Vc-Vb) Vertical ramp output Line 310
VLIN: 11111
No.8047-33/44
LA76818A
Continued from preceding page.
Input signal Vertical S-shaped correction @16 Symbol VScor16 Test point Input signal Y IN: Horizontal/ vertical sync signal PAL Test method Monitor the pin 23 vertical ramp output and measure the voltage at line 36, line 60, line 155, line 179, line 274 and 298. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. VScor16 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc) Line 298 Vertical ramp output Line 179 Line 60 Line 274 Line 155 Line 36 @0 VScor0 Monitor the pin 23 vertical ramp output and measure the voltage at the line 36, line 60, line 155, line 179, line 274 and line 298 with VSC = 00000. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. VScor0 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc) Bus conditions VS: 10000
15
@31
VScor31
Monitor the pin 23 vertical ramp output and measure the voltage at line 36, line 60, line 155, line 179, line 274 and 298 with VSC = 11111. Assign the respective measured values to Va, Vb, Vc, Vd, Ve and Vf. Vscor31 = 0.5((Vb-Va)+(Vf-Ve))/(Vd-Vc)
VSC: 11111
No.8047-34/44
LA76818A
Control Register Bit Allocation Map
Sub Address 00000000 MSB DA0 T.Disable 1 00001 Vest Timing 0 00010 Sync.Kill 0 00011 VSEPUP 0 00100 H BLK L 1 00101 H BLK R 1 00110 V.TEST 0 00111 R.BIAS 0 01000 G.BIAS 0 01001 B.BIAS 0 01010 RGB.Test4 0 01011 Drive.Test 0 01100 A2.SW 0 01101 Blank.Def 0 01110 A.MONI.SW 0 01111 S.TRAP.SW 1 10000 OSD Cnt.Test 0 10001 0 R.DRIVE 1 Half tone 0 B.DRIVE 1 Sub.Bright 1 Bright 1 Contrast 1 OSD Contrast 1 0 Sharpness 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 Half tone Def 1 1 G.DRIVE 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 V.COMP 1 1 1 0 0 V.SC 0 0 0 0 0 DA1 AFC gain&gate 0 Audio.Mute 0 V.SIZE 1 V.KILL 0 0 V.POSI 1 V.LIN 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DA2 H.FREQ 1 Video.Mute 0 1 H.PAHSE 1 0 0 0 0 1 1 1 1 DA3 DATA BITS DA4 DA5 DA6 LSB DA7
COUNT.DOWN.MODE 0 0 0
10010
Tint.Test 0
10011
Color.Test 0
0 Filter.Sys
10100
Video SW 0
0 CbCr_IN
10101
Gray Mode 0
0 Y_APF 0
10110
VBLK SW 0
10111
Y Gamma Start 0 0
No.8047-35/44
LA76818A
Continued from preceding page.
Sub Address DA0 00011000 Auto.Flesh 0 11001 Cont.Test 0 11010 R-Y/B-Y Gain Balance 1 11011 0 0 0 DA1 C.Ext 0 Digital OSD 0 MSB DA2 C.Bypass 1 Brt.Abl.Def 0 DA3 C_Kill ON 0 Mid.Stp.Def 0 DA4 C_Kill OFF 0 RGB Temp SW 0 R-Y/B-Y Angle 1 0 0 0 DATA BITS DA5 Color.Sys 0 Bright.Abl.Threshold 1 0 0 0 0 DA6 LSB DA7
B-Y DC Level (White-Balance) 1 0 Volume 0 VOL.FIL 0 deem.TC 0 0 RF.AGC 1 VIF.Sys.SW 0 1 FM.LEVEL 0 C.VCO Adj SW 0 0 * 0 * 0 Tint.Tthrough 0 * 0 Hlock.Vdet 0 0 * 0 * 0 * 0 IF.TEST1 0 1 * 0 * 0 * 0 * 0 * 0 * (0) 0 0 0 0
11100
Audio SW 0
11101
OVER.MOD.SW
0 11110 FM.Mute 0 11111 VIDEO.LEVEL 1 100000 Pre/Over SW 0 100001 C.VCO Adjust 0 100010 * (0) 100011 * 0 100100 * 0 100101
0 SIF.Sys.SW 0
0 FM.Gain
0 IF.AGC 0
0 * 0 * 0 * 0 * 0 * 0 OVER.MOD.LEVEL 1
0 * 0 * 0 * 0 * 0 * 0
0 * 0 * 0 * 0 * 0 * 0
0 * 0 *
* 0 * 0 * 0
VIDEO.LEVEL.OFFSET 0 1
No.8047-36/44
LA76818A
Control Register Truth Table
Register Name T.Disable AFC gain&gate 0 HEX Tset Enable Auto(Gain) Auto(Gate) V Reset Timing Audio.Mute Video.Mute Sync.Kill Vsepup V.KILL Vertical Test Drive.Test Half Tone Half Tone Def Blank.Def S.TRAP.SW OSD Cnt.Test Coring Gain (w/Defeat) Tint.Test Color.Test Video.SW Gray Mode Cross B/W CbCr_IN G-Y Angle VBLK SW Normal Active Active Sync active normal Vrt active Normal Normal Min (Dark) Half Tone on Blanking Bypass ON Normal Defeat Normal Normal Internal Mode Normal Normal SECAM Input mode 240deg 24H to 262H (NTSC) 25H to 309H (PAL) FBPBLK.SW fsc or Csync Y APF Pre/Over-shoot adj. WPL Ope. Point (w/Defeat) Y Gamma Start DC Rest. Blk.Str.start (w/Defeat) Blk.Str.Gain Auto Flesh C.Ext C.Bypass C_Kill ON C_Kill OFF Cont.Test Digital OSD Brt.ABL.Def Mid.Stp.Def RGB Temp SW OVER.MOD. (circuit) SW VOL.FIL FM.Mute de-em TC. VIF.Sys.SW FM Gain IF.AGC Pre/Over SW C.VCO Adj SW FBP not or fsc Y Trap Normal Defeat Y Gamma off 100% Defeat Min OFF Internal Mode Bypass OFF Auto Mode Auto Mode Normal Analog Brt ABL On Mid Stp On -1Vbe circuit OFF Normal Active 50s 38.0MHz 50kHz dev. AGC active Pre-shoot Adj. direction: Plus 1 HEX Test Disable Gain:Fast Non-Gate 1/4H Shift Mute Mute Sync killed Vsepup Vrt killed Vrt S Corr Test Mode Half Tone off No Blank Bypass OFF Test Mode Min Test Mode Test Mode External Mode Gray OSD Black CbCr Input mode 253deg 29H to 256H (NTSC) 30H to 304H (PAL) FBP or Composit Sync Y APF +10ns High Min 106% Low ON External Mode Bypass ON Killer ON Killer OFF Test Mode Digital Brt ABL Off Mid Stp Off Flat circuit ON Filte OFF Mute 75s 38.9MHz 25kHz dev. AGC defeat Over-shoot Adj. direction: Minus 45.75MHz 39.5MHz +20ns 113% Max +30ns Low Max 128% High White Cross Max Max Vrt Lin Vrt Size 2 HEX 3 HEX
No.8047-37/44
LA76818A
Continued from preceding page.
Register Name C.VCO Adjust (C.VCO Adj SW: 0) (C.VCO Adj SW: 1) Tint Through Hlock.Vdet VIDEO.LEVEL.OFFSET normal -30kHz Tint Control Enable Individual Operation direction: Minus 0 HEX +30kHz -60kHz Tint Control Disable Normal Center direction: Plus 1 HEX +60kHz -90kHz 2 HEX +90kHz -120kHz 3 HEX
No.8047-38/44
LA76818A
Control Register Truth Table
COUNT DOWN MODE
50Hz/60Hz MODE 0 HEX 1 HEX 2 HEX 3 HEX 4 HEX 5 HEX 6 HEX 7 HEX Auto 50Hz 60Hz Auto Auto 50Hz 60Hz Auto Standard/Non-Standard MODE Auto Auto Auto Auto Non-Standard Non-Standard Non-Standard Non-Standard
Color System
0 HEX 1 HEX 2 HEX 3 HEX 4 HEX 5 HEX 6 HEX 7 HEX Auto Mode1 PAL/NTSC/4.43NTSC(/SECAM) Auto Mode2 PAL-M/PAL-N/NTSC PAL PAL-M PAL-N NTSC 4.43NTSC SECAM
Filter System
Y Filter 0 HEX 1 HEX 2 HEX 3 HEX 4 HEX 5 HEX 6 HEX 7 HEX 8-15HEX 3.58MHz Trap 3.58MHz Trap 4.43MHz Trap 4.43MHz Trap 6.0MHz Trap 6.0MHz Trap 6.0MHz Trap 6.0MHz Trap 4.286MHz Trap Chroma Filter Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF Peaked 4.43MHz BPF Symmetrical 4.43MHz BPF Peaked 3.58MHz BPF Symmetrical 3.58MHz BPF Peaked 4.43MHz BPF Symmetrical 4.43MHz BPF Symmetrical 4.43MHz BPF
No.8047-39/44
LA76818A
Status Byte Truth Table
Register RF.AGC IF.LOCK V.TRI 50/60 ST/NONST H.LOCK KILLER 0 HEX RF.AGC.OUT = "L" IF.PLL Lock V.Triger Undetected 50 Non-Standard Horiz Unlocked KILLER OFF 1 HEX RF.AGC.OUT = "H" IF.PLL Unlock V.Triger Detected 60 Standard Horiz Locked KILLER ON
Color System
No.8047-40/44
LA76818A
Initial Conditions
Register T.Disable AFC gain&gate H.FREQ V Reset Timing Audio.Mute Video.Mute H.PHASE Sync.Kill V.SIZE VSEPUP V.KILL V.POSI H BLK L H BLK R V.LIN V.SC V.TEST V.COMP COUNT.DOWN.MODE R.BIAS G.BIAS B.BIAS RGB Test 4 R.DRIVE Drive Test Half Tone Half Tone Def G.DRIVE A2 SW B.DRIVE Blank.Def Sub.Bias A.MONI.SW Bright S.TRAP.SW Contrast OSD Cnt.Test OSD Contrast Coring Gain (w/Defeat) Sharpness Tint.Test Tint Color.Test Color Video.SW Trap.Test Filter.Sys Gray Mode Cross B/W CbCr_IN G-Y Angle Color Killer Ope. 1 HEX 0 HEX 3F HEX 0 HEX 0 HEX 0 HEX 10 HEX 0 HEX 40 HEX 0 HEX 0 HEX 20 HEX 4 HEX 4 HEX 10 HEX 00 HEX 0 HEX 7 HEX 0 HEX 00 HEX 00 HEX 00 HEX 0 HEX 7F HEX 0 HEX 1 HEX 1 HEX 8 HEX 0 HEX 7F HEX 0 HEX 40 HEX 0 HEX 40 HEX 1 HEX 40 HEX 0 HEX 0 HEX 0 HEX 00 HEX 0 HEX 40 HEX 0 HEX 40 HEX 0 HEX 4 HEX 2 HEX 0 HEX 0 HEX 0 HEX 0 HEX 4 HEX VBLK SW FBPBLK.SW fsc or Csync Y_APF Pre/Over-shoot Adj. WPL Ope. Point (W/Defeat) Y Gamma DC. Rest. Blk.Str.start (W/Defeat) Blk.Str.Gain Auto Flesh C.Ext C.Bypass C_Kill ON C_Kill OFF Color System Cont.Test Digitsl OSD Brt.Abl.Def Mid.Stp.Def RGB Temp SW Bright.Abl.Threshold R-Y/B-Y Gain Balance R-Y/B-Y Angle B-Y DC Level R-Y DC Level Audio.SW Volume OVER.MOD.SW VOL.FIL RF.AGC FM.Mute deem.TC VIF.Sys.SW SIF.Sys.SW FM.Gain IF.AGC VIDEO.LEVEL FM.LEVEL Pre/Over SW C.VCO Adj SW C.VCO Adjust H lock.Vdet VIDEO.LEVEL.OFFSET IF.TEST1 OVER.MOD.LEVEL Register 0 HEX 1 HEX 0 HEX 0 HEX 0 HEX 0 HEX 0 HEX 2 HEX 0 HEX 1 HEX 0 HEX 0 HEX 1 HEX 0 HEX 0 HEX 0 HEX 0 HEX 0 HEX 0 HEX 0 HEX 0 HEX 4 HEX 8 HEX 8 HEX 8 HEX 8 HEX 0 HEX 00 HEX 0 HEX 0 HEX 20 HEX 0 HEX 0 HEX 1 HEX 1 HEX 0 HEX 0 HEX 4 HEX 10 HEX 0 HEX 0 HEX 0 HEX 0 HEX 1 HEX 0 HEX 8 HEX
No.8047-41/44
LA76818A
Control Register Descriptions
Register Name T Disable AFC Gain & gate H Freq. V Reset Timing Audio Mute Video Mute H PHASE Sync Kill Vertical Size Vsep.up Vertical Kill V POSI (Vertical DC) H BLK L H BLK R V LIN (Vertical Linearity) Vertical S-Correction Vertical Test Vertical Size Compensation Count Down Mode Red Bias Green Bias Blue Bias Red Drive Drive Test Half Tone Half Tone Defeat Green Drive A2.SW Blue Drive Blank Def Sub Bias A.MONI.SW Brightness Control S.TRAP.SW Contrast Control OSD Contrast Test OSD Contrast Control Coring Gain Select (with Defeat) Sharpness Control Tint Test Tint Control Color Test Color Control Video SW Trap.Test Filter System Gray Mode Cross B/W CbCr_Input Enable SW G-Y Angle Select Color Killer Operational Point Select Vertical Blanking SW Bits 1 1 6 1 1 1 5 1 7 1 1 6 3 3 5 5 2 3 1 8 8 8 7 1 2 1 4 1 7 1 7 1 7 1 7 1 2 2 6 1 7 1 7 1 3 3 1 2 1 1 3 1 General Description Disable the Test SW & enable Audio/Video Mute SW Select horizontal first loop gain & H-sync gating on/off Align ES Sample horizontal frequency Select Vertical Reset Timing Disable audio outputs Disable video outputs Align sync to flyback phase Force free-run mode Align vertical amplitude Select vertical sync. separation sensitivity Disable vertical output Align vertical DC bias H-Blanking Control (Left side of the screen) H-Blanking Control (Right side of the screen) Align vertical linearity Align vertical S-correction Select vertical DAC test modes Align vertical size compensation Select vertical countdown mode Align Red OUT DC level Align Green OUT DC level Align Blue OUT DC level Align Red OUT AC level Enable Drive control DAC test modes Adjust half tone DC level Half tone defeat SW Align Green OUT AC level Select 5.74MHz FM.Det Align Blue OUT AC level Disable RGB output blanking Align common RGB DC level Select FM Output/Selected Audio Output Customer brightness control Select Snd Trap bypass Customer contrast control Enable OSD Contrast DAC test mode Align OSD AC level Select Coring Gain (0hex: Defeat) Customer sharpness control Enable tint DAC test mode Customer tint control Enable color DAC test mode Customer color control Select Video source Trap Test Select Y/C Filter mode OSD Gray Tone Enable Service Test Mode (normal/Black/White/Cross) Enable CbCr Input (Disable SECAM Input) Select G-Y Angle Select Color Killer Operational Point Select VBLK Period
No.8047-42/44
LA76818A
Continued from preceding page.
Register Name FBPBLK.SW fsc or Csync SW Y APF Enable SW Pre/Over-shoot Adjustment WPL Ope. Point (W/Defeat) Y Gamma Start DC Restoration Select Blk. Str. Start Point Select (w/Defeat) Blk. Str. Gain Select AutoFlesh C Ext C Bypass C Kill On C Kill Off Color System Cont Test Digital OSD SW Bright ABL Defeat Bright Mid Stop Defeat RGB Temp SW Bright ABL Threshold R-Y/B-Y Balance R-Y/B-Y Angle B-Y DC Level R-Y DC Level Audio SW Volume Control OVER.MOD.SW Volume Filter Defeat RF AGC Delay FM Mute de-em TC. VIF System SW SIF System SW FM Gain IF AGC Defeat Video Level FM Level Pre/Over SW C VCO Adjust SW C VCO Adjust Tint Through H Lock Vdet VIDEO.LEVEL.OFFSET IF TEST1 OVER.MOD.LEVEL Bits 1 1 1 2 2 2 2 2 2 1 1 1 1 1 3 1 1 1 1 1 3 4 4 4 4 1 7 1 1 6 1 1 2 2 1 1 3 5 1 1 2 1 1 2 1 4 General Description Enable RGB Blanking or FBP Select fsc output or Composit sync output Select the frequency characteristic of 3.58MHzTrap. It is useful for 3.58MHzTrap or APF. Select Pre-shoot Width Select WPL Operating Point Enable luminance coring Select Luma DC Restoration Select Black stretch Start Point (w/ Defeat) Select Black stretch Gain Enable AutoFlesh function Selected-C In SW on Select Chroma BPF bypass C Kill Mode (1: Enable Killer circuit) Disable Killer circuit Select Color System Enable contrast DAC test mode Select Digital/Analog OSD Disable brightness ABL Disable brightness mid stop Select temperature characteristic of RGB Output Align brightness ABL threshold R-Y/B-Y Gain Balance R-Y/B-Y Angle B-Y DC Level (White-Balance) R-Y DC Level (White-Balance) Select Audio source Customer volume control Select overmodulation circuit ON/OFF Disable volume DAC filter Align RF AGC threshold Disable FM outputs Select de-emphasis Time Constant Select 38.0/38.9/39.5/45.75 Select 4.5/5.5/6.0/6.5 Select FM Output Level Disable IF and RF AGC Align IF video level Align FM output level Select control for Pre/Over-shoot Adjustment Select the direction of C. VCO adjustment Align C. VCO's frequency Select tint control operation (enable or disable) Select vertical sync. Operation Align IF video level Select test modes Align overmodulation performance
No.8047-43/44
LA76818A
Reed Status
RF.AGC IF.LOCK V.TRI 0: RFAGC OUT = low, 1: RFAGC OUT = high See the separately provided documentation (application note) for details. 0: IF. PLL=Lock, 1: IF. PLL=Unlock Returns the VCD internal vertical trigger detection circuit output to the bus. The internal memory state is updated on each vertical period. 1HEX: Detected. 50/60 ST/NONST Returns the VCD internal 50Hz/60Hz detection circuit output to the bus. Returns the VCD standard (262.5H) or nonstandard internal vertical trigger detection circuit output to the bus. Returns the output of the flip-flop that determines the VCD internal mode in real time. 1HEX: Standard For more information, refer to the separately provided documentation and then contact your Sanyo representative with questions. H.Lock Performs a phase comparison between FBP and Hsync, integrates that output, and detects the locked state about 40H after the horizontal VCO locks. This state is returned in real time in response to a bus read. 1HEX: Locked KILLER Returns the state of the color killer. Note, however, that the time constant is long and a time of roughly one vertical period (16 ms) is required for detection. Applications must be careful concerning the wait period associated with a device state change. This state is returned in real time in response to a bus read. 1HEX: Killer on Color sys Returns the color system state See the register truth table's color system table. The read status is the same as that for bus write.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above.
This catalog provides information as of November, 2007. Specifications and information herein are subject to change without notice. PS No.8047-44/44