Escolar Documentos
Profissional Documentos
Cultura Documentos
Formula para el clculo de la perdida de carga o energa por friccin:.........................2 Prdida de energa (Energy Loss).................................................................................................. 2 Profundidad Crtica (Critical Depth)............................................................................3 Prdida en Conexiones (Junction Losses).....................................................................3 Coeficiente de Perdida en conexiones (K) (Junction Loss Coefficients)..........................4 Flujo Supercrtico (Supercritical Flor)..........................................................................5 Salto Hidrulico (Hydraulic Jump)...............................................................................6 Diagrama de flujo de trabajo......................................................................................7 Chequeo del cdigo de diseo (Check the Design Codes).............................................................7 Minimum Pipe Size (Tamao mnimo del tubo)..........................................................................7 Maximum Pipe Size (Tamao mximo de tubo).........................................................................7 Design Velocity (Velocidad de diseo).......................................................................................7 Minimum Slope (Pendiente mnima).......................................................................................... 8 Maximum Slope (pendiente maxima)........................................................................................ 8 Default N Value (Coef Rugosidad)............................................................................................. 8 Match Crowns............................................................................................................................ 8 Match Inverts............................................................................................................................ 8 Load IDF curves............................................................................................................................. 8 Draw the lines............................................................................................................................... 9 Add line data................................................................................................................................. 9 Add inlet data.............................................................................................................................. 11 Compute..................................................................................................................................... 11
Donde: Dc = Profundidad Critica D = Dimetro de la tubera Q = Caudal Nota: si DC es mayor que el 85% de D. entonces se ejecuta un mtodo de ensayo y error para encontrar la energa mnima especifica. Para mayor informacin sobre este mtodo de calculo computacional de la Profanidad Critica puede consultar Open Channel Hydraulics, McGraw - Hill, 1985, by Richard H. French. (Canal Abierto de Hidrulica, McGraw - Hill, 1985, por Richard H. French.)
lnea presenta demasiados cambios de direccin o de dimetro, debidos a condiciones especiales de topografa o espacio, debern considerarse dichas prdidas.
Donde: K = Coeficiente de perdida en conexiones. V = Velocidad del flujo existente en la conexin. Nota: las perdidas por conexiones no son computadas para lneas en Profundidad Critica o lineas que fluyen bajo el control de una entrada.
Para ngulos menores de 90 grados, el Hydraflow Storm Sewer Extensin utiliza la ecuacin siguiente para calcular el coeficiente de perdida en la conexin K
Si la conexin es una entrada, entonces K se multiplica por 1.5; K nunca estar por debajo de 0.15 en pozos de registros, o 0.5 para las entradas. Un valor conservador para este coeficiente es de 1.0, que asume toda la velocidad y se pierde en el pozo de registro y la conexin es simplemente un depsito alimentado por las lneas entrantes. La velocidad de entrada se pierde y se convierte en presin esttica.
El momento (M) del perfil subcritico es igual al momento del perfil supercrtico.
Donde: Q = Caudal A = Seccin transversal del flujo Y = Distancia desde la superficie del agua al centroide de A. La localizaron de el salto es el punto a lo largo de la lnea cuando M1=M2 y se reporta la distancia como desde el extremo de aguas abajo de la lnea. La longitud del salto es difcil de determinar, especialmente en secciones circular. Una longitud de salto aceptable, generalmente esta entre 4 y 6 veces la profundidad posterior. Hydraflow Storm Sewers Extensin asume un valor de 5 para la longitud del salto. La siguiente ilustracin muestra el clculo de los perfiles del flujo supercrtico con saltos hidrulicos. La lnea de puntos representa la lnea de energa (EGL)
Sewers Extension utiliza una tubera de 18 pulgadas. Hydraflow Storm Sewers Extension utiliza esta velocidad a lo largo con la ecuacin de Manning n para determinar la pendiente del tubo.
Match Crowns
Seleccione esta opcin para que coincida la corona de los tubos sin importar su tamao. Vea alineacin en la grafica. Opcin activada por defecto.
Match Inverts
Seleccione esta opcin para que coincida la corona de los tubos sin importar su tamao. Vea alineacin en la grafica.
match those that you are presently using. The rainfall data file is set up from the main application window. After you enter the IDF data, Hydraflow Storm Sewers Extension stores the IDF curves in a user-defined file name. This file is loaded each time Hydraflow Storm Sewers Extension is started. During design, Hydraflow Storm Sewers Extension uses the IDF curve and the computed Tc to compute the intensity.
also carried downstream to be added to other downstream lines when Accumulate Known Qs is selected in the Design Codes. If you selected Use Inlet Captured Flows in the Design Codes, Known Qs are ignored on manholes or non-inlet type junctions. Drainage Area (ac, ha) Enter the drainage area that contributes to this line only. Hydraflow Storm Sewers Extension accumulates the areas during the calculations. Runoff Coefficient (C) Enter the runoff coefficient corresponding to this drainage area. Hydraflow Storm Sewers Extension computes a weighted or composite coefficient by clicking the on the side toolbar. Hydraflow Storm Sewers Extension computes a weighted C using the three C values specified in the Design Codes. For more information, see Runoff Coefficients (C) on page 81. Tc Options Specify the option of using a known Tc or calculating it using either the FAA or TR55 methods. Choose by clicking the corresponding option button or from the drop-down list on the Pipes tab. Inlet time is the time it takes for runoff to travel from the most remote upstream point in the drainage area to the inlet in question. Known Tc. This is the default method. Simply enter the Tc in minutes. FAA method. Collected data from airfield drainage by the Army Corps of Engineers was used to develop this method and is now widely used in urban drainage design. TR-55 method. This option allows you to compute Tc by using the 3-component Tc as used by TR-55. Hydraflow Storm Sewers Extension has a built-in TR-55 worksheet that computes Tc. Inlet Time (min) Enter the inlet time (overland flow time) for this catchment. It is usually 10 to 20 minutes. This is not the computed Tc for the system but the Tc for this inlet only. Hydraflow Storm Sewers Extension computes the overall Tc during the calculations. If FAA or TR55 was chosen for the Tc Method, click the corresponding FAA or TR55 button to open the built-in Tc calculator. If using the Pipes tab, click the special function button % to open the Tc calculator. Your cursor must be on the Inlet Time column to activate. The computed values are automatically entered as the Inlet Time. NOTE You can model a system with Rational method flow information and without inlets. Draw your system using manholes at junctions while specifying drainage areas, C values, and inlet times. In the reports there is no inlet analysis if you use this design method. Tc Method FAA or TR55 for more information, see Calculate Tc Using the FAA Method on page 25 and Calculate Tc Using the TR55 Worksheet on page 26. Invert Elevation Down (ft, m) Enter the invert elevation for the downstream end of the line. Enter 0 to have Hydraflow Storm Sewers Extension determine the value. When you are adding upstream lines, Hydraflow Storm Sewers Extension automatically places a default value equal to the upstream invert of the downstream line. Slope of Invert (opt.) (%) Optionally, enter the slope of the line in percent. If you enter a value, Hydraflow Storm Sewers Extension computes the upstream invert and uses it as the default value for the upstream invert elevation. If you do not enter a slope, Hydraflow Storm Sewers Extension computes it based on the invert elevations you enter. Invert Elevation Up (ft, m) Enter the elevation of the invert at the upstream end of the line. Enter 0 to have Hydraflow Storm Sewers Extension set it for you. This item is automatically set to 0 if the downstream invert is set to 0. Hydraflow Storm Sewers Extension does not design downstream inverts when the upstream invert is fixed. Line Rise (in, mm) Enter the diameter of the pipe or the height of the box or elliptical pipe in inches (mm). Enter 0 to have Hydraflow Storm Sewers Extension set the pipe size. If you entered 0 for any of the invert elevations, Hydraflow Storm Sewers Extension sizes a circular pipe based on the design velocity. Otherwise the design is based on Manning's Equation setting, where the slope of the energy grade line is equal to the slope of the invert. Line Type Displays the current line type in the list box between the Line Rise and Line Span input boxes. Hydraflow Storm Sewers Extension can model circular, box and elliptical pipes. To change the line type, click the arrow in the list box and specify elliptical, box, or circular. Hydraflow Storm Sewers Extension does not design pipe sizes for elliptical or box sections. NOTE Hydraflow Storm Sewers Extension does not directly model arch pipes because of inconsistent depth-to-area relationships. If you need to model a pipe section such as an arch, it is recommended you use an equivalent section of a box or elliptical section. Set the invert and crown to match conditions. Then compute the span that gives an equivalent cross-sectional area of the desired section. Line Span (in, mm)
10
Enter the width of the box or elliptical section in inches. If this line is a circular pipe, press Tab to accept the default. No. Barrels Select the number of barrels from the drop-down list. You do not need to adjust the Line Length. The Line Length is the distance between junction centerlines. Manning's n-Value Enter the roughness coefficient for this line. Hydraflow Storm Sewers Extension assumes a default value that you set in the Design Codes. To choose other n-values, click the arrow on the list box and select a new value. Junction Loss Coeff. Enter the junction loss coefficient for this line. This number usually ranges from 0.15 to 1.5 and is multiplied by the velocity head of the flow exiting the junction of this line. The computed loss is then added to the hydraulic grade line (HGL) at the upstream end of this line (HGUP) to produce the HGJ, and is typically the starting HG for any incoming lines. Hydraflow Storm Sewers Extension automatically computes and assigns junction loss coefficients, based on the junction configuration, if you specify Automatic on the Design Codes - Calculations tab. For more information, see Design Code Settings on page 12 and Computational Methods on page 63. Inlet / Rim Elev. (ft, m) Enter the finish or natural ground elevation at the upstream end of the line. This item is used for design when the Calculation Option Design is chosen. Otherwise this entry is only cosmetic. You must enter the downstream Inlet/Rim elevation when entering Line
Compute
11
1. Dnstr Line No: Puede cambiar la lnea descendente o seleccionar manualmente una lnea
descendente con la lnea Dnstrm text = cuadro de la barra de estado. Introduzca el nmero de lnea que desee y haga clic en aceptar la lnea descendente nueva. (Outfall= desague) 2. Line Length (m): longitud de la lnea 3. Defl Angle (deg): ngulo de deflexin 4. Junction Type: seleccione el tipo de entrada que tiene a la lnea. 5. Known Q (cms): caudal que se aade en el flujo desde aguas arriba 6. Drnge Area (ha) 7. Runoff Coef (C): coeficiciente de escorrentia correspondiente a el area de captacion. 8. Inlet Time (min): tiempo de concentracion 9. Invert Elev Dn (m): elevacin invertida abajo 10. Line Slope (%): pendiente 11. Invert Elev Up (m) 12. Line Rise (mm): Introduzca el dimetro de la tubera mm. Introduzca 0 para que Hydraflow Storm Extensin Alcantarillado establecer el tamao de la tubera. Si ha introducido 0 para cualquiera de las elevaciones invertidas, Hydraflow Storm Extensin Alcantarillado tamaos un tubo circular basado en la velocidad de diseo. De lo contrario, sera establecido en base a la ecuacin de Manning, donde la pendiente de la lnea de energa es igual a la pendiente de la invertida. 13. Line Type: Muestra el tipo de lnea actual en el cuadro de lista entre el lnea Rise y Lne Span 14. Line Span (mm): introduzca el ancho de la caja o seccin elptica 15. No. Barrels: Seleccione el nmero de barriles de la lista desplegable. No es necesario ajustar la longitud de lnea. El Longitud de la lnea es la distancia entre lneas centrales de conexiones. 16. N Value (n): Introduzca el coeficiente de rugosidad de esta lnea. Hydraflow Storm Extensin Alcantarillado asume un valor por defecto que establece en los cdigos de diseo. Para seleccionar otros valores de n, haga clic en la flecha en el cuadro de lista y seleccionar un nuevo valor. 17. J-Loss Coef (K): Introduzca el coeficiente de prdida de la salida de esta lnea. Este nmero generalmente vara desde 0,15 hasta 1,5 18. Inl/Rim Elev Dn (m): introduzca la elevacin de termino en el terreno natural, en el extremo de aguas abajo de la lnea. Este elemento se utiliza para el diseo cuando la opcin de clculo de diseo es elegido. 19. Inl/Rim Elev Up (m): introduzca la elevacin de termino en el terreno natural, en el extremo de aguas abajo de la lnea. Este elemento se utiliza para el diseo cuando la opcin de clculo de diseo es elegido
12
Minor loss: Junction Loss Coeff. x Velocity Head. Prdida de conexiones Coef. x la carga de velocidad
13