Escolar Documentos
Profissional Documentos
Cultura Documentos
Where Cb maybe taken as 1.0 since the maximum moment does not occur at the supports, rt is the radius of the compression web area, taken about the axis in the plane of the web. Steel is A 36 steel with yield strength Fy = 248MPa. Which of the following most nearly gives the most economical (lightest) section that will limit the flexural stress to the allowable value.
Item 1 2 3 4 5 6 7 8
Unit Price (Pesos) 1,000 10,000 5,000 6,000 3,000 1,500 2,000 25,000
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Design and Construction CE Board Exam Nov. 1997
The approved agency estimate (AAE) of a Govt. project is 500M. The bids are: Bidder A : P354,000,000 Bidder B : P639,000,000 Bidder C : P483,000,000 Bidder D : P583,000,000 Bidder E : P295,000,000 Bidder F : P385,000,000 The implementing rules and regulation of Pres. Decree No. 1594 states that no award of contract shall be made to a bidder whose bid price is higher than Allowable Government Estimate(AGE) or the Approved Agency Estimate(AAE) is defined as one half the sum of the (AAE) and the average of all responsive bids. For the purposes of determining the average of responsive bids, bids higher than 120% of the AAE or lower than 60% of AAE shall not be considered. Which bidder wins the contract for the Govt. project?
Design and Construction CE Board Exam Nov. 1997 Design and Construction CE Board Exam Nov. 1997
A 50mm diameter split barrel sample is driven into the ground and the load of a cased burbale by means of blows form 65kg mass hammer falling freely through a distance of 760mm. The sample is driven a total of 450mm into the soil. Which of the following is the test best described by this procedure? A floor is made up of 150mm thick concrete slab and 50mm thick finish both of which has a unit weight of 24kN/m3. The floor also carries ceiling whose weight is 720Pa and a live load of 2400Pa. The floor is supported by simply supported steel beams with a span of 10m spaced at 4.6m on centers with compression flange rigidly attached to the concrete floor. The steel is A36 with yield strength (Fy) = 248MPa. The allowable shear stress specified in the 1992 NSCP is 0.40Fy. Considering the weight of the beam, which of the following sections is the most economical (lightest) section for the given load assuming that shear stress governs the design.
a) Dutch Cone Penetration Test b) Standard Proctor Test c) Standard Penetration Test d) Vane shear test
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Design and Construction CE Board Exam Nov. 1997
A steel plate is 360mm wide and 20mm thick with four bolt holes cut into the plate as shown in the figure s-3. The general expression for the specification method for computing the net area is:
Neglecting the weight of the beam, which of the following most nearly gives the maximum value of the load P that the member can support.
Where: T = thickness of plate B = width H = diameter of holes S = pitch g = gage Which of the following most nearly gives the critical net area (An) of the section in accordance with the 1992 NSCP.
a) Statically indeterminate to the first degree b) Unstable c) Statically indeterminate to the second degree d) Statically determinate
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Pu and Pc are the summations for all columns in a story. For frames not braced against sideways, both b and s shall be computed. For frames braced against sideway, s shall be taken as 1.0. In equation (5.10.7) for members braced against sideway and without transverse loads between supports Cm maybe taken as:
But not less than 0.40. For all other cases, Cm shall be taken as 1.0 A rectangular tied concrete column has dimensions of 300mm x 380mm. The column length is 4.5m. is to be constructed in a frame braced against sideway (the effective length factor K can be taken as 1 and EI = 34MN-m2.. The column is loaded in single curvature by the ultimate factored moment of 110kN.m at its top end and 120kN.m at
The volume of the mold for this test is 1/30cu.ft. (946,000 cubic millimeters). Which of the following most nearly gives the value of the optimum moisture content of the soil?
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
its bottom end. The column carries factored axial loads due to dead load of 150kN, 350kN due to live load. Which of the following gives the magnified factored moment (Mc) that will be used it design the steel reinforcement in accordance with the NSCP 1992. reduced concrete beam has a width of 300mm and an effective of 400mm. Concrete strength is 24MPa and steel yield strength is 340MPa. Which of the following most nearly gives the maximum allowable steel area (As) in accordance with the 1992 NSCP strength design method.
Which of the most nearly gives the change in effective pressure at a depth of 12m. on account of lowering of water table Sp.gr. of soil is 2.60
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Design and Construction CE Board Exam Nov. 1997
The soil is said to be non-plastic if the liquid limit is less than: a) 90 b) 50 c) 20 d) 60
Unsupported length, Lu Effective length factor, K Flexural rigidity, EI Magnification factor, delta Moment magnifying coef., Cm
Determine the ultimate load Pu in kN that this colum can carry. Use phi = 0.70.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Where is the new location of the neutral axis from the top of the slab in mm. Use n = 10m transform the area of concrete to steel.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Hydraulics CE Board Exam Nov. 1997
A vertical wall retains a cohesionless soil which has a unit weight of 14 kN/m3, and angle of internal friction of 26 degrees. If the wall is 5.0m high, what is the total active soil pressure in kN on the wall. Assume a unit length of wall.
Hydraulics CE Board Exam Nov. 1997 Hydraulics CE Board Exam Nov. 1997
Determine the discharge in MLD of a 2800 mm gravity flow concrete aqueduct 4km long with a head loss of 5.6m. Assume pipe is flowing just full with roughness coeff. of 0.015. A drainage canal in the shape of trapezoidal with a bottom width of 2.5m. side slopes 1:1 carries water at a depth of 3m. Find the velocity using chezys formula, S = 0.0009, n = 0.015
Hydraulics CE Board Exam Nov. 1997 Hydraulics CE Board Exam Nov. 1997
A H2O tank with 3 m is filled with H2O. The H2O level is 2.30 m above a nozzle. What is the velocity of H2O coming out of the nozzle? Neglect losses Determine the discharge in MLD of a 2800 mm gravity flow concrete aqueduct with a hydraulic gradient of 0.0015. Assume pipe is flowing full with coefficient of roughness = 0.015
Hydraulics CE Board Exam Nov. 1997 Hydraulics CE Board Exam Nov. 1997
A drainage canal in the shape of trapezoidal with bottom width of 2.5m and side slopes of 1 horizontal to 1.5 vertical, carries H2O at a depth of 3m. Find the discharge in m3/s using the chezys Formula. S = 0.0009, n = 0.615. Precipitation station x was inoperative for part of a month during which a storm occurred. The respective storm totals at three surrounding stations A, B and C were 98.80 and 110mm. The normal annual precipitation amounts at stations x A, B and C are respectively, 880, 1008, 842 and 1080mm. Estimate the storm precipitation for station x.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Hydraulics CE Board Exam Nov. 1997 Hydraulics CE Board Exam Nov. 1997
An open vessel 3m. in diameter contains water at a depth of 3.05m and 0,91 m of oil (S = 0.8) the tank is accelerated upward at 3 m/s2. Find the pressure at the bottom. An open vessel 30cm. in diameter and 90cm high is filled with water to a depth of 45 cm. Find the magnitude of the velocity such that the vortex is just at the bottom.
Hydraulics CE Board Exam May 1997 Hydraulics CE Board Exam Nov. 1997
A device attached at the end of the pipe with a cover use for cleaning. a) b) c) d) clean out man hole culvert none A rectangular weir was installed to control the flow. If the flow is set at 3cu.m/s, Cd = 0.6 and the length is 0.8m., what must the height be?
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Hydraulics CE Board Exam May 1997
Water has velocity of 4 m/s through a 40 cm pipe. The discharge through the pipe is:
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Hydraulics CE Board Exam May 1997
A pressure gauge at elevation 6m. at the side of a tank containing a liquid reads 90 kPa. Another gauge at elevation 4m. reads 110 kPa. Compute for the specific weight.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Mathematics CE Board Exam Nov. 1997
From the following differential leveling notes, compute the difference in elevation between station 5 and 6. STA 1 2 3 4 5 6 1 B.S. 2.565 10.875 7.035 3.560 7.186 4.123 5.821 1.946 5.741 9.736 7.977 4.123 F.S. ELEV. 33.971
Mathematics CE Board Exam Nov. 1997 Mathematics CE Board Exam Nov. 1997
The elements of a compound curve are as follows: I1 = 18 I2 = 23.5 D1 = 2 D2 = 4 The correct distance between point E and f IS 213.5 m. If a 100m. tape that is 0.025 m. too long is used to measure EF, what will be the measured distance in meters?
Determine the stationing of the P.C. if the stationing of P.I. = 42 + 89.6. Use arc basis.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Mathematics CE Board Exam Nov. 1997
The bases of a right prism is a hexagon with one of each side equal to 6 cm. The bases are 12 cm. apart. What is the volume of the right prism?
Mathematics CE Board Exam Nov. 1997 Mathematics CE Board Exam Nov. 1997
Determine the length of the latus rectum of the ellipse having an equation 4x2 + 9y2 64x + 54y + 301 = 0. The cost of equipment is P500,000 and the cost of installation is P30,000. If the salvage value is 10% of the cost of equipment at the end of 5 years, determine the book value at the end of the fourth year. Use straight line method.
Mathematics CE Board Exam Nov. 1997 Mathematics CE Board Exam Nov. 1997
The volume of a pyramid is 140 cu.m. If it has a rectangular upper base of 3 m. x 4 m. and an altitude of 5 m., determine the dimensions of the lower base.
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Mathematics CE Board Exam Nov. 1997
Find the area of the region bounded by the curve r2 = 16 Cos .
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Mathematics CE Board Exam May 1997 Mathematics CE Board Exam May 1997
From the given close traversed, find the corrected bearing of line EA. LINE AB BC CD DE EA DIST(m.) 895 315 875 410 650 BEARING S. 7029 E. S. 2628 E. S. 6533 W. N. 4531 W. N. 10 E. Differentiate Arc Cos 4x:
Mathematics CE Board Exam May 1997 Mathematics CE Board Exam May 1997
What time after 3 oclock will the hands of the clock be together for the first time? In the sum of the interior angles of a polygon with an equal sides is 1080, find the number of sides of a polygon?
Mathematics CE Board Exam May 1997 Mathematics CE Board Exam May 1997
Find the distance from point A(4,2) to B(-5,1).
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION
CE BOARD 1997
Mathematics CE Board Exam May 1997
Find the slope of a line having a parametric equation of x = 2 + t and y = 5 3 t
Mathematics CE Board Exam May 1997 Mathematics CE Board Exam May 1997
A circular cone having an altitude of 9 m. is divided into 2 segments having the same vertex. If the smaller altitude is 6 m., find the ratio of the volume of small cone to the big cone. Which of the following numbers should be change to make all the numbers form an Arithmetic progression when properly arranged?
BM1 ********2.565
PHILIPPINE INSTITUTE OF CIVIL ENGINEERS UAE CHAPTER CIVIL ENGINEERING BOARD EXAM 2013 PREPARATION