Escolar Documentos
Profissional Documentos
Cultura Documentos
Questions:
1. Under the CSA designations for documents, what is the equivalent CSA number
for ANSI/TIA/EIA-568 standard called?
a. CSA T530
b. CSA T525
c. CSA T529
d. CSA T527
a. copper
b. protected
c. horizontal
d. backbone
a. 800
b. 3000
c. 2000
d. All the other answers are incorrect
a. Floor Distributor
b. Campus Distributor
c. Building Distributor
d. All the above are correct
5. Under the CSA designations for documents, what is the equivalent CSA number
for ANSI/TIA/EIA-569 standard called?
a. CSA T530
b. CSA T525
c. CSA T529
d. CSA T527
a. bus
b. star
c. ring
d. framed
a. TSB75
b. T527
c. 568B.2
d. ANSI/EIA/TIA-606
a. 568
b. 606
c. 569
d. 607
9. Under the ANSI/TIA/EIA designations for documents, what is the number of the
“Commercial Building Standard for Telecommunications Pathways and
Spaces” called?
a. TIA/EIA-568
b. TIA/EIA-569
c. TIA/EIA-606
d. TIA/EIA-607
10. Each individual work area shall be serviced with a minimum of _______
telecommunications outlets (TO).
a. 2
b. 4
c. 3
d. 6
11. Under the CSA designations for documents, what is the equivalent CSA number
for ANSI/TIA/EIA-607 standard called?
a. CSA T530
b. CSA T525
c. CSA T529
d. CSA T527
12. A structured wiring system based on CAT 5e cable, can handle top data rate
a. of about 100Mbps.
b. greater than 10Gbps.
c. between 10 and 50 Kbps.
d. better than fiber optics.
13. When a MUTOA is used the horizontal cable maximum length will be affected,
based on the length of the work area cord. The maximum length of the work area
cord is _______ meters.
a. 13
b. 9
c. 22
d. 17
a. Floor Distributor
b. Campus Distributor
c. Building Distributor
d. All the above are correct
a. 75
b. 90
c. 100
d. 110
16. Under the ANSI/TIA/EIA designations for documents, what is the number of the
“Administration Standard for the Telecommunications Infrastructure of
Commercial Buildings” called?
a. TIA/EIA-568
b. TIA/EIA-569
c. TIA/EIA-606
d. TIA/EIA-607
17. Under the 568 standard, the “Jumper/Patch Cord Maximum Length
Limitations” for cable in the telecom room is __________ meters.
a. 3
b. 6
c. 10
d. 20
18. Which of the following establishes performance and technical criteria for various
cabling system configurations?
a. TIA/EIA-568
b. TIA/EIA-569
c. TIA/EIA-606
d. TIA/EIA-607
a. 75
b. 90
c. 100
d. 110
21. Under the CSA designations for documents, what is the equivalent CSA number
for ANSI/TIA/EIA-606 standard called?
a. CSA T530
b. CSA T525
c. CSA T528
d. CSA T568
22. Under the 568 standard, what is the minimum bend radius for backbone cable?
a. 2 x diameter
b. 4 x diameter
c. 8 x diameter
d. 10 x diameter
23. Under the ANSI/TIA/EIA designations for documents, what is the number of the
“Commercial Buildings Telecommunications Cabling Standard” called?
a. TIA/EIA-568
b. TIA/EIA-569
c. TIA/EIA-606
d. TIA/EIA-607
24. Delay Skew: The difference between the _____________________ of any two
pairs within the same cable sheath.
a. NEXT
b. permanent link
c. propagation delay
d. channel link
25. Which of the following generally refers only to fiber optic cable?
a. T527
b. TSB-67
c. 11801
d. 568B.3
26. Under the 568 standard, the “Jumper/Patch Cord Maximum Length
Limitations” for cable in the work area is __________ meters.
a. 3
b. 6
c. 10
d. 20
27. Which of the following enables the planning and installation of a structured
cabling system for commercial buildings?
a. TIA/EIA-568
b. TIA/EIA-569
c. TIA/EIA-606
d. TIA/EIA-607
28. Wiring a cable with T568A termination at the workstation end and T568B
termination at the patch panel end will result in what?
a. bad pair
b. cross-over pair
c. twisted pair
d. router pair
29. Under the 568 standard, what is the minimum bend radius for horizontal UTP (4-
pair) cable?
a. 2 x diameter
b. 4 x diameter
c. 8 x diameter
d. 10 x diameter
30. To insure ________, the cable network is built to a standard.
a. administration
b. cost reduction
c. performance
d. reliability
31. Under the 568 standard, when spicing (mechanical or fusion) a fiber optic cable the
maximum attenuation must be less than _________ dBs.
a. 1.5
b. 0.75
c. 0.3
d. 6
32. Which management organization was responsible for the 568 standard?
a. ISO
b. ANSI
c. CSA
d. TelNet
33. Using a 568SC connector, the beige colored connector indicated ________.
a. keyed duplex
b. single mode connector/coupling
c. multimode connector/coupling
d. None of the above are correct
34. Under the 568 standard, which section covers “Optical Fiber Cabling
Components”?
a. B.1
b. B.2
c. B.2-1
d. B.3
35. Patch cords can be connected directly from a MUTO to work area equipment. (T/
F)
a. TRUE
b. FALSE
36. Under the 568 standard, the fiber connection (mated pair) a fiber optic cable the
maximum insertion loss must be less than _________ dBs.
a. 1.5
b. 0.75
c. 3
d. 6
a. engineering protractor
b. set of AutoCad drawings
c. CEC addendum
d. approved standard
38. Under the 568 standard, what is the minimum bend radius for horizontal ScTP
cable?
a. 2 x diameter
b. 4 x diameter
c. 8 x diameter
d. 10 x diameter
39. Under the 568 standard, when spicing (mechanical or fusion) a fiber optic
single-mode cable the minimum return loss should be _________ dBs.
a. 10
b. 20
c. 26
d. All the above values are incorrect
40. Using a 568SC connector, the blue colored connector indicated ________.
a. keyed duplex
b. single-mode connector/coupling
c. multimode connector/coupling
d. None of the above are correct
ICT444 Assignment #6
Questions:
1. Under 568 there are two ways of wiring the workstation jacks and patch panel
jacks. Which one is popular in Alberta?
a. T568-B
b. TSB-75
c. T568-A
d. The thin technique
a. FT-6.
b. FT-4 or less.
c. T568-B.
d. hard to work with.
3. The “Rule of thumb” for TOTAL horizontal cabling or channel is ______ meters.
a. 800
b. 90
c. 305
d. 100
a. TRUE
b. FALSE
a. 100
b. 92
c. 50
d. 150
6. What is the term that indicates the difference in propagation delay between the
fastest and slowest pair within the same cable sheath, usually expressed in
nanoseconds (ns)?
a. color twist
b. impedance
c. NEXT
d. delay skew
a. propagation
b. impedance
c. attenuation
d. “Cable Skew”
8. Which of the following is the minimum level of cable for voice communications?
a. CAT 2
b. CAT 4
c. CAT 3
d. CAT 5
9. Energy coupled from one conductor to another is a good thing for data
communications. (T/F)
a. TRUE
b. FALSE
10. Of all the characteristics of LAN cable operation, _________ has the greatest
effect on network performance.
a. cost
b. CAT 5
c. redundancy
d. crosstalk
11. A multi-tenant commercial building has a life expectancy of at least _____ years.
a. 30
b. 40
c. 50
d. 60
a. 20
b. 30
c. 40
d. 50
a. layouts
b. linkages
c. work orders
d. None of the other answers are correct
14. Using the “Commercial Building Standard for Telecommunications Pathways
and Spaces” document, a “Rule of Thumb”: Allow ____ sq.ft. of plywood for each
_____ sq. ft. of floor space.
a. 1, 200
b. 1, 300
c. 2, 200
d. 2, 300
a. Brown
b. White
c. Orange
d. Green
a. CSA T525
b. CSA T530
c. CEC 232c
d. CSA C527
a. 400
b. 300
c. 200
d. 500
a. framing
b. management
c. location
d. NONE of the above fit this answer!
19. Using the “CSA T525” document, what would you be wiring?
a. 10 ft x 11 ft
b. 10 ft x 15 ft
c. 15 ft x 20 ft
d. There is NO recommended room sizing
a. 90
b. 100
c. 305
d. 1000
a. FD
b. firestops
c. frames or racks
d. fiber
a. Blue
b. Brown
c. Green
d. White
a. 3-inches
b. 7-inches
c. 5-inches
d. 4-inches
25. In Canada, the “Residential and Light Commercial Telecommunications
Wiring Standard” document is called:
a. CSA 526
b. CSA T528
c. CSA T525
d. There is NO such thing in Canada!
a. Blue
b. Brown
c. Green
d. This is NOT the CORRECT document to go to!
27. Using the “ANSI/TIA/EIA-606” document in the USA, then which document
would you refer to as a French version in Canada?
a. CSA T527
b. CSA T528
c. CSA T568-B.3
d. There is NO French version in Canada!
a. 0.50, 100
b. 0.75, 100
c. 1, 200
d. None of the other answers are correct
29. What do we call the assembly that helps to reduce cabling moves, adds and
changes in a modular furniture settings.
a. Consolidation Point
b. MUTO
c. Pull-Box
d. Hand-Hold (HH)
30. Using the “Commercial Building Standard for Telecommunications Pathways
and Spaces” document, in buildings larger than _________ usable sq. ft., a
locked, dedicated, enclosed room is recommended.
a. 20,000
b. 30,000
c. 40,000
d. 70,000
a. 20%
b. 30%
c. 40%
d. 50%
32. What is the term used to re-establish the integrity of fire-rated structures when
these barriers have been penetrated by cable?
a. fire-safe
b. fire-cement
c. plenum
d. firestops
a. BCDxxx
b. MCxxx
c. ICxxx
d. There is NO such thing as a BD!
34. Using the “ANSI/TIA/EIA-568” document, what is the maximum link distance
in meters?
a. 90
b. 100
c. 305
d. 1000
35. What is the ISO document number that the 568 came from?
a. T525
b. IEEE 802.3
c. 11801
d. There is NO ISO document
36. Using the “ANSI/TIA/EIA-569” document, more than one telecom room per
floor is required if floor area served exceeds _______ square feet.
a. 5,000
b. 10,000
c. 15,000
d. 20,000
a. TIA/EIA-568-B.1
b. TIA/EIA-568-B.3
c. TIA/EIA-568-B.FO
d. TIA/EIA-568-B.2-ad10
a. WSxxx
b. WAxxx
c. TCxxx
d. Jxxx
a. Underfloor Ducts
b. J-hooks
c. Multi-channel Raceway
d. Trenchduct
a. 1, 100
b. 1, 200
c. 2, 150
d. 1, 1100
ICT444 Assignment #7
Questions:
1. Looking at the picture (below), what is the normal maximum length of the “A”
label?
a. 33 feet
b. 6 meters
c. 3 meters
d. 25 feet
a. TRUE
b. FALSE
5. What standard would you refer to if you were going to wire the device shown in the
picture (below)?
a. CSA T527
b. TSB-67
c. ANSI/EIA/TIA 606
d. ISO/IEC 11801
a. Reversed Pair
b. Split Pair
c. Matched Pair
d. Crossed Pair
e. There is NO mistake on this column!
7. The arrow in the picture (below) point to what type of block?
a. BIX
b. 110
c. RJ-45
d. Type 66
8. What is the max link distance for a cable system wired as EIA/TIA 568?
a. TRUE
b. FALSE
10. Always use an industry accepted labeling format such as the one specified in
a. CSA T530
b. TSB-75
c. ANSI/TIA/EIA-606
d. CSA T527
11. Using the “CSA T527 ” document, which of the following is not a major
component of this standard?
a. TBB
b. TGB
c. TGMB
d. TBBIBC
12. Looking at the picture (below), what is the normal maximum length of the “E” label?
a. 33 feet
b. 6 meters
c. 3 meters
d. 25 feet
13. The picture (below) is a good wiring job (T/F)
a. TRUE
b. FALSE
14. Using the “Commercial Building Grounding and Bonding Requirements for
Telecommunications” document, what is the minimum bonding conductor size?
a. 6 AWG
b. 8 AWG
c. 10 AWG
d. None of the other answers are correct
15. From the administration standard, what is the alphanumeric ID code for a splice
called?
a. SLxxx
b. SExxx
c. Sxxx
d. SPxxx
a. TBB
b. TMGB
c. Main CO ground
d. TBBIBC
a. blue
b. green
c. orange
d. brown
18. Under the 568 standard, what is the maximum number of hierarchical levels of
backbone cross-connects allowed?
a. 1
b. 2
c. 3
d. 4
19. Under the 568 standard, one MUTOA can serve a maximum of ____ work areas.
a. 9
b. 12
c. 15
d. As many as you want!
20. Using the “CSA T527 ” document, A _______ is not intended to serve as the only
conductor providing a ground fault current return path.
a. TBB
b. TBBIBC
c. rack
d. TGBM
21. From the picture (below), what type of wiring mistake is column 2?
a. Reversed Pair
b. Split Pair
c. Matched Pair
d. Crossed Pair
e. There is NO mistake on this column!
22. The design aspects of the equipment room are found in the TIA/EIA-569-A
standard. Is this a TRUE or FALSE statement?
a. TRUE
b. FALSE
23. Using the “Commercial Building Grounding and Bonding Requirements for
Telecommunications” document, typically, there should be _______ TMGB per
building.
a. 2
b. 5
c. 1
d. 0
24. What is the name of the device in the picture below called?
a. TBB
b. TMGB
c. Main CO ground
d. TBBIBC
26. Using the “CSA T527 ” document, a water pipes shall not be used as a TBB. Is
this statement TRUE or FALSE?
a. TRUE
b. FALSE
27. Under the Canadian standard for cabling backbone, the maximum UTP distance is
800 meters. Is this statement TRUE or FALSE?
a. TRUE
b. FALSE
28. Under the 568 standard, main and intermediate cross-connect jumpers or patch
cord lengths should NOT exceed ______ meters.
a. 10
b. 20
c. 60
d. 90
29. Using the “ANSI/EIA/TIA 607” document, TBB conductors should be installed
without __________, where practicable.
a. orange cables
b. splices
c. bonding
d. NONE of the other answers are correct!
30. Under the 568 standard, are transition points from round to flat under carpet cable
allowed?
a. YES
b. NO
31. Under the 568 standard, each TO in each work area should have a minimum of
_____ information outlet ports.
a. 1
b. 4
c. 6
d. 2
32. From the picture (below), what type of wiring mistake is column 4?
a. Reversed Pair
b. Split Pair
c. There is NO mistake on this column!
d. Crossed Pair
33. On a 8-position modular jack, two pairs are swapped between the T568A wiring
and the T568B wiring terminations. What are the colors of those swapped pairs?
a. TRUE
b. FALSE
35. Using the “ANSI/EIA/TIA 607” document, the location of the TMGB primary
protectors shall be separated by a minimum of ___________ from any DC power,
switchboard or high frequency cables even when these cable are contained in
metallic or EMT conduit
a. 100 mm
b. 200 mm
c. 300 mm
d. 500 mm
36. On an 8-position modular jack, two pairs are swapped between the T568A wiring
and the T568B wiring terminations. What are the cable pairs that are swapped?
a. pairs 1 and 4
b. pairs 3 and 2
c. pairs 2 and 4
d. pairs 1 and 2
37. From the picture (below), what type of wiring mistake is column 1?
a. Reversed Pair
b. Split Pair
c. There is NO mistake on this column!
d. Crossed Pair
38. Are bundled and hybrid cables allowed for use in horizontal cabling (HINT:
check TIA/EIA-568-B.2 specification)
a. YES
b. NO
a. TRUE
b. FALSE
40. Using the “CSA T527” document, metallic cable shield can be used as a TBB in
new installations. Is this statement TRUE or FALSE?
a. TRUE
b. FALSE
Assignment 5
1 c 11 d 21 c 31 c
2 d 12 a 22 d 32 a
3 c 13 c 23 a 33 c
4 b 14 a 24 c 34 d
5 a 15 c 25 d 35 a
6 b 16 c 26 a 36 b
7 b 17 b 27 a 37 d
8 b 18 a 28 b 38 c
9 b 19 b 29 b 39 c
10 a 20 c 30 d 40 b
Assignement 6
1 c 11 c 21 c 31 c
2 a 12 d 22 d 32 d
3 d 13 c 23 c 33 c
4 b 14 a 24 c 34 a
5 a 15 c 25 c 35 c
6 d 16 b 26 d 36 b
7 c 17 b 27 b 37 b
8 c 18 b 28 b 38 b
9 b 19 b 29 b 39 b
10 d 20 a 30 a 40 a
Assignment 7
1 c 11 c 21 a 31 d
2 d 12 b 22 a 32 b
3 d 13 b 23 c 33 d
4 a 14 a 24 c 34 b
5 a 15 c 25 a 35 c
6 d 16 b 26 a 36 b
not in
7 17 test 27 37 c
8 c 18 b 28 38 a
9 b 19 b 29 b 39 a
10 c 20 a 30 b 40 b