Você está na página 1de 5

JAR-66 MODULE 4 1. THE COLOUR OF AN LED IS DUE TO A) THE ACTIVE MATERIALS B) A PLASTIC LENS C) A COLOUR FILTER 2.

PICTURE OF AN SCR IS IT A A) SCR B) FET C) PNP TRANSISTOR 3. A DIODE IS CONNECTED ACROSS AN LED TO A) PREVENTS THE LED WORKING UNTIL A CERTAIN VOLTAGE LEVEL IS REACHED B) PROTECTS THE LED IF A.C.IS CONNECTED C) PREVENTS BACK EMF WHEN THE LED IS SWITCHED OFF 4. GERMANIUM DIODES ARE USED FOR A) SIGNAL DETECTION B) RECTIFICATION C) 5. WHEN TESTING A DIODE WITH A MULTIMETER THE POSITIVE LEAD IS CONNECTED TO A) ANODE, NEGATIVE TO THE CATHODE B) CATHODE, NEGATIVE TO EARTH C) CATHODE, NEGATIVE TO ANODE 6. WHAT ELECTRONIC DEVICE CONNECTS ACROSS A RELAY TO PREVENT BACK EMF A) BI-DIRECTIONAL ZENER DIODE B) SCHOKKY DIODE C) GUNN DIODE 7. WHICH DIODE HAS A LOWER FORWARD BIAS VOLTAGEA) SILICON B) GERMANIUM C) BOTH THE SAME 8. A MULTI LAYER PCB HAS A) CIRCUITS AND COMPONENTS ON BOTH SIDES B) MULTIPLE LAYERS OF CIRCUITS C) CIRCUITS ON ONE SIDE, COMPONENTS ON THE OTHER 9. WHEN A PCB IS FULLY ASSEMBLED IT IS COATED WITH A) INSULATING VARNISH B) WAX C) CONFORMAL COATING 10. A DESYNN ROTOR IS A) A PERMANENT MAGNET B) ELECTROMAGNET C)

11. WHEN A STEP INPUT TO A SERVO SYSTEM OVERSHOOTS AND OSCILLATES IT IS A) UNDER DAMPED B) OVER DAMPED C) CRITICALLY DAMPED 12. A DIFFERENTIAL SYNCHRO HAS A) ONE 3 PHASE ROTOR AND ONE 3 PHASE STATOR B) ONE 3 PHASE ROTOR AND ONE SINGLE PHASE STATOR C) ONE SINGLE PHASE ROTOR AND ONE 3 PHASE STATOR 13. A DIFFERENTIAL SYNCHRO CAN BE USED AS A A) TRANSMITTER B) TRANSMITTER OR A RECEIVER C) RECEIVER 14. POSITION FEEDBACK IN A SERVO SYSTEM IS A) IN PHASE WITH THE INPUT B) ANTI-PHASE WITH THE INPUT C) 90 DEGREES OUT OF PHASE WITH THE INPUT 15. VELOCITY FEEDBACK IS A) PROPORTIONAL TO SERVOMOTOR SPEED B) INVERSELY PROPORTIONAL TO SERVOMOTOR SPEED C) THE SAME ALL THE TIME 16. VELOCITY FEEDBACK WHEN THE SERVOMOTOR HAS STOPPEDIS A) AT A MAXIMUM IN-PHASE WITH THE INPUT B) MAXIMUM ANTI-PHASE WITH THE INPUT C) ZERO 17. A TORQUE SYNCHRO HAS AC. POWER TO THE A) STATOR B) ROTOR AND STATOR C) ROTOR 18. A ZENER DIODE IS USED FOR A) RECTIFICATION B) VOLTAGE STABILISATION C) 1.what will be the output frequency of a three phase half have rectifier:a.double b.same frequency c.thrice. 2.in a bridge rectifier: a.output is equal to the whole of the transformer secondary winding. b.output equal to the whole of the transformer primary winding. c.output equal to the half of the transformer secondary winding.

3.a resolver had a. 2 windings(one stator one rotor). b.6 windings(3stator 3 rotor). c.4 windings(2stator 2 rotor). 4.for signal diodes we use: a.germanium. b.silicon. c.graphite. 5.for a zener doide we generally use: a.germanium. b.silicon. c.gallium. 1. An RC Connected Amp has? Ans. No DC across. 2. When a PN junction is forward biased, it conducts via? Ans. Majority carriers. 3. Thermal runaway in a transistor refers to. Ans. High current flow when temperature rises. 4. When is maximum voltage induced into the rotor of a control synchro? Ans. 0 degrees 5. Resistors and capacitors to couple stages of amplifiers so that? Ans. Only AC can be supplied. 6. An astable multivibrator is a? Ans. Free running vibrator. 7. Op amps use what power supply? Ans. 5v to 15v DC. 8. To check the output of a Synchro stator it would be preferable to use? Ans. A Valve Voltmeter. 9. Synchro capacitors are connected into synchro systems to? Ans. Increase the accuracy of the control synchro. 10. In a Slab Desynn transmitter the? Ans. Pick offs rotate on the slab resistor. 11. The purpose of the Flywheel incorporated into a synchro? Ans. To prevent oscillations. 12. If in a servo system, the amplitude from the feedback system is below normal, the servo will? Ans. Oscillate. 13. A Desynn instrument has a positive irregular increasing error, you would adjust? Ans. Lever length.

14. Torque synchro receiver bearing friction will cause? Ans. Misalignment. 15. A control system synchro pointer is? Ans. Motor driven.

16. A DC signal converted to a phase sensitive AC is? Ans. Modulation. 17. If velocity feedback in a servo system is above optimum, this will cause? Ans. Sluggish operation. 18. In an Integrated Circuit, the components are mounted by? Ans. Metal oxide film etched onto the surface. 19. For a NPN transmitter to conduct the collector circuit has to be? Ans. More positive than the base. 20. When forward biased, current flow is mainly due to the? Ans. Majority carriers. 21. When forward biased, the? Ans. Positive is connected to the P type and the negative is connected to the N type. 22. In a PNP transmitter, which way does the conventional current flow? Ans. Emitter to Collector. 23. In an Integrated circuit, the components are inserted? Ans. By doping in successive layers. 24. The typical voltage drop across an LED is? Ans. 2 V 25. In an electronic circuit with an operational amplifier connected in the push-pull configuration, the circuit? Ans. Utilises both sides of the input signal. 26. Pin 3 on an Op Amp has a + symbol. This designates? Ans. Non-inverting input. 27. An advantage of a FET when compared to a bi-polar transmitter is? Ans. The input resistance is higher. 28. The semiconductor material most commonly used in chips is? Ans. Silicon 29. The typical bandwidth for an audible frequency amplifier is? Ans. 10 100 KHz. 30. What control system is used on an input that gives a controlled predetermined output? Ans. Closed loop.

31. Increasing velocity feedback from optimum will give? Ans. A sluggish performance.

32. A rate control servo system with a steady input voltage will give? Ans. Constant speed. 33. Where are de-coupling capacitors used in digital circuits? Ans. Close to the positive pin. 34. What are the majority carriers for forward biased PN junction devices? Ans. Electrons and holes. 35. The resistance measured using an AVO between Collector and Emitter of a transmitter is? Ans. Same both ways. 36. Germanium in its pure state is? Ans. Neutral. 37. Common Collector has the following characteristics? Ans. Medium voltage gain, High current gain and Non-inverting output. 38. Two push pull transmitters have what commoned? Ans. Emitters. 39. In a Common Emitter Amplifier, RE is used for? Ans. Stabilisation. 40. If the reverse bias voltage across a Diode is too high? Ans. Load current reverses. 41. The rotor coil of a Synchrotel? Ans. Is stationary. 42. An increase in the amplitude of a rate feedback signal will cause? Ans. Reduced hunting. 43. An increase in Negative feedback will? Ans. Decrease system sensitivity. 44. In integrated circuit is manufactured by? Ans. Doping impurities into layers of intrinsic material. 45. A de-coupling capacitor in a PCB is used to? Ans. Pass AC only. 46. A monostable vibrator? Ans. Is switched on by a trigger pulse then within a pre set time will eventually return to its original state. 47. Position feedback is used to? Ans. Ensure control surface moves to the demanded position by the controls

Você também pode gostar