Escolar Documentos
Profissional Documentos
Cultura Documentos
Unit I 1. Gantry Girders; Industrial building frames : Q.1. Design a Gantry girder to carry an electric overhead traveling crane for the following data: a) Span of gantry girder = 6 m b) Crane capacity = 200KN c) Span of crane girder = 12 m d) Weight of crane = 80 KN e) Minimum approach distance of crane hook = 1.20 m f) Weight of crane girder = 180KN g) Wheel base = 3.50 m h) Height of rails = 80 mm i) Weight of rails = 300 mm Take Fy = 250 Mpa. Q.2. Design a suitable section for Gantry girder for the following data:-i)Crane capacity =220 KN ii) Weight of crab = 50 KN iii) Span of gantry girder = 7 m iv) Weight of crane excluding crab = 160 KN v) End clearance = 1.2 m vi) Wheel base = 2.80 m vii) C/C of gantry girder rails = 18 m viii) Electrically operated single crane is to be considered. Q.3. Design a suitable section for Gantry girder for the following data:-i) Crane capacity = 210KN ii) Weight of crab = 60 KN iii) Span of gantry girder = 7.5 m iv) End clearance = 1.25 m v ) Wheel base = 3 m vi) C/C of gantry girder rails = 16 m vii) Weight of crane excluding crab = 170 KN viii) Electrically operated single crane is to be considered. Q.4. Design a suitable section for Gantry girder for the following data:-i) Crane capacity = 250 KN ii) Weight of crab = 75 KN iii) Span of gantry girder = 6.4 m iv) End clearance = 1.25 m v ) Wheel base = 2.4 m
vi) C/C of gantry girder rails = 16 m vii) Weight of crane including crab = 180 KN viii) Electrically operated single crane is to be considered. Q.5. Design a Gantry girder to be used in an industrial building carrying an electric overhead traveling crane for the following data:-i) Crane capacity = 125 KN ii) Weight of crane = 150 KN iii) Weight of trolley, electric motor etc. = 40 KN iv) Self weight of rail section = 300 N/m v ) Wheel base = 3 m vi) C/C of gantry girder rails = 14 m vii) Weight of crane including crab = 180 KN viii) C / C distance of columns = 8 m ix) Minimum clearance = 1.20 m
Q.4. Design one top, one bottom, and one vertical member for an N type bridge truss. Use following data : a) Span of truss = 18 m (6 panels @ 3m c/c) b) Height of truss = 1.4 m c) Width of bridge = 2 m d) Live load on bridge = 4 KN/m2 e) R.C.C. Bridge flooring 125 mm thick Q.5.Design one top, one bottom, and one vertical and one diagonal member for the foot bridge truss shown in fig, live load shall be5 KN/m 2 .
20 m @ 2.5 m c/c
Section B Unit III: Storage Vessels; Q.1. Design an overhead rectangular water tank 1,00,000 litres. The height of columns of staging is 6 m. Depth of water in the tank shall not exceed 2.50 m. Design: a) Bottom plates b) T- stiffners (T- covers) c) Side plates d) Stays e) Check for composite T- section as stiffners. Q.2. Design Container for an overhead steel water tank to store 75,000litres of water. Choose suitable dimension for base, height of the containers and free board. Q.3. Design Container for an overhead steel water tank to store 70,000 litres of water. Choose suitable dimension for base, height of the containers and free board. Q.4. An overhead rectangular water tank consists of a container of plan dimensions 7.5 m * 12.5 m and height 2.5 m. The tank is supported at two-tier beam system placed on top of four columns. C/C distance between columns along shorter span of container is 6.2 m while longer span of container it is 11.3 m. Design: i) Bottom plates of container and joint between two plates. ii) Upper tier and lower tier of beams, Assume adequate spacing and number of beams. Q.5. Design rectangular overhead steel water tank of capacity 1,20,000 litres of water. The height of staging is 8 m. Depth of water in tank shall not exceed 2.4 m. Design upto upper tier beams. Section B Unit III: Steel Bunkers ;Open web sections Q.1. Design rectangular steel bunker of 11 m length and 5.5 m width supported on eight columns (four along each long side) to store coal of bulk density 8 KN/m3 and angle of internal friction 35o , height of vertical portion 3.8 m , height of hopper portion is 3.8 m . Q.2. Design rectangular steel bunker of 12 m length and 6 m width supported on 8 columns (4 along each long side) to store coal of bulk density 8 KN/m 3 and angle of internal friction 35o , height of vertical portion 4 m , height of hopper portion is 4 m .
Q.3. Design rectangular steel bunker of 13 m length and 6.5 m width supported on eight columns (four along each long side) to store coal of bulk density 8 KN/m3 and angle of internal friction 35o , height of vertical portion 4 m , height of hopper portion is 4 m . Q.4.a) Design open web section for a fixed beam of span 6 m and subjected to a udl of 40 KN/m on entire span. ---------------------------------------------------------------------------------------------------------
b) State the various types of shear connectors used in composite constructions. c) State and explain the method of design for composite section consisting of I-beam.