Escolar Documentos
Profissional Documentos
Cultura Documentos
Router(config)#do show startup-config Using 1697 out of 245752 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname santa_cruz_lobito ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef !
! ! username acsnoc privilege 15 secret 5 $1$f7il$61yvFlJuybgL4Ycu0vjy/1 username auto_sueco privilege 15 secret 5 $1$kfml$HpIJjaAKl9qLSUlRlCF48. username oni privilege 15 secret 5 $1$tVzz$/nURLDPRAUz0R.SADn0do/ ! ! ! interface Tunnel10 description #### Tunnel to Auto_Sueco_Benguela ### ip address 10.10.6.18 255.255.255.252 keepalive 10 3 tunnel source 10.12.253.235 tunnel destination 10.12.253.237 ! interface Tunnel20 description *** Tunnel to Lobito_Lja_Asparts *** ip address 10.10.6.6 255.255.255.252 keepalive 10 3 tunnel source 10.12.253.235 tunnel destination 10.12.253.234 ! interface Tunnel30 description *** Tunnel to Sede *** ip address 10.10.6.9 255.255.255.252 keepalive 10 3 tunnel source 10.12.253.235 tunnel destination 10.12.253.233 ! interface FastEthernet0/0 description *** WAN ***
ip address 10.12.253.235 255.255.255.248 duplex auto speed auto ! interface FastEthernet0/1 description *** LAN *** ip address 172.29.7.25 255.255.255.0 ip tcp adjust-mss 1400 duplex auto speed auto ! ip classless ip route 0.0.0.0 0.0.0.0 10.10.6.10 ip route 172.29.11.0 255.255.255.0 10.10.6.5 ip route 172.29.13.0 255.255.255.0 10.10.6.17 ! ip http server ! snmp-server community acsnoc RO snmp-server community public RO ! control-plane ! ! line con 0 login local line aux 0 line vty 0 4 privilege level 15 login local line vty 5 15
Router(config)#username metuzalem password zalem Router(config)#line console 0 Router(config-line)#username metuzalem password zalem Router(config)#line console 0 Router(config-line)#login local Router(config-line)#exit Router(config)# *Aug 1 21:52:11.359: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB d evice has been inserted in port 1. *Aug 1 21:52:12.051: %USBFLASH-5-CHANGE: usbflash1 has been inserted! *Aug 1 21:52:12.059: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values i n partition table or boot sector. Device needs formatting before use!c % Incomplete command.
1697 bytes copied in 0.212 secs (8005 bytes/sec) Router(config)# *Aug 1 21:54:55.667: %USB_HOST_STACK-6-USB_DEVICE_DISCONNECTED: A USB device ha s been removed from port 1. *Aug 1 21:54:55.783: %USBFLASH-5-CHANGE: usbflash1 has been removed! *Aug 1 21:56:23.035: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB d evice has been inserted in port 1.
*Aug 1 21:56:23.723: %USBFLASH-5-CHANGE: usbflash1 has been inserted! *Aug 1 21:56:23.727: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values i n partition table or boot sector. Device needs formatting before use! Router(config)#do copy startup-config usb port 1 copy startup-config usb port 1 ^ % Invalid input detected at '^' marker.
1697 bytes copied in 0.324 secs (5238 bytes/sec) Router(config)#do copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Router(config)#exit Router# *Aug 1 21:59:17.759: %SYS-5-CONFIG_I: Configured from console by console Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#enable secret zalem Router(config)#do copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Router(config)#exit Router#e *Aug 1 22:00:15.991: %SYS-5-CONFIG_I: Configured from console by consolexit
Username: metuzalem Password: Router>enable Password: Router#reload Proceed with reload? [confirm]y
*Aug 1 22:01:16.031: %SYS-5-RELOAD: Reload requested by metuzalem on console. R eload Reason: Reload command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc.
Initializing memory for ECC . c2811 platform with 262144 Kbytes of main memory Main memory is configured to 64 bit mode with ECC enabled
You must reset or power cycle for new config to take effect rommon 2 > reset c2811 platform with 262144 Kbytes of main memory Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xef3d74 Self decompressing the image : ################################################# ############################################################################# ###
########################## [OK]
Smart Init is enabled smart init is sizing iomem ID 0003E7 MEMORY_REQ TYPE
0X003DA000 C2811 Mainboard 0X000021B8 Onboard USB 0X002C29F0 public buffer pools 0X00211000 public particle pools
TOTAL:
0X008AFBA8
If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 10Mb. Using 3 percent iomem. [10Mb/256Mb]
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 28-Nov-07 21:09 by stshen Image text-base: 0x400A265C, data-base: 0x41544910
Port Statistics for unclassified packets is not turned on. Cisco 2811 (revision 49.46) with 251904K/10240K bytes of memory. Processor board ID FCZ121472H7 2 FastEthernet interfaces DRAM configuration is 64 bits wide with parity enabled. 239K bytes of non-volatile configuration memory. 3915760K bytes of USB Flash usbflash1 (Read/Write) 62720K bytes of ATA CompactFlash (Read/Write)
*Aug 1 22:03:12.063: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB d evice has been inserted in port 1. *Aug 1 22:03:12.179: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t o up *Aug 1 22:03:12.203: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state t o up *Aug 1 22:03:12.755: %USBFLASH-5-CHANGE: usbflash1 has been inserted! *Aug 1 22:03:12.763: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values i
n partition table or boot sector. Device needs formatting before use! *Aug 1 22:03:13.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/0, changed state to down *Aug 1 22:03:13.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/1, changed state to down *Aug 1 22:03:14.415: %SYS-5-CONFIG_I: Configured from memory by console *Aug 1 22:03:14.839: %SYS-5-RESTART: System restarted -Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 28-Nov-07 21:09 by stshen *Aug 1 22:03:14.839: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start *Aug 1 22:03:15.043: %SYS-6-BOOTTIME: Time taken to reboot after reload = 119 seconds *Aug 1 22:03:16.339: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Aug 1 22:03:16.355: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
Username: Username: metuzalem Password: Router>enable Password: Router#sh star Using 643 out of 245752 bytes !
version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! enable secret 5 $1$L.IZ$T.MDX2MrPeju/TPoZsnPl/ ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef ! ! ! username metuzalem password 0 zalem ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto
speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! ip classless ! no ip http server ! ! control-plane ! ! line con 0 login local line aux 0 line vty 0 4 login ! scheduler allocate 20000 1000 ! end
*Aug 1 22:06:24.015: %SYS-5-RELOAD: Reload requested by metuzalem on console. R eload Reason: Reload command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc.
Initializing memory for ECC . c2811 platform with 262144 Kbytes of main memory Main memory is configured to 64 bit mode with ECC enabled
You must reset or power cycle for new config to take effect rommon 2 >confreg 2102 not found rommon 3 confreg 2102
monitor: command " " not found rommon 4 > reset c2811 platform with 262144 Kbytes of main memory Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized program load complete, entry point: 0x8000f000, size: 0xcb80 program load complete, entry point: 0x8000f000, size: 0xcb80
Smart Init is enabled smart init is sizing iomem ID 0003E7 MEMORY_REQ TYPE
0X003DA000 C2811 Mainboard 0X000021B8 Onboard USB 0X002C29F0 public buffer pools 0X00211000 public particle pools
TOTAL:
0X008AFBA8
If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 10Mb. Using 3 percent iomem. [10Mb/256Mb]
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 28-Nov-07 21:09 by stshen Image text-base: 0x400A265C, data-base: 0x41540840
Port Statistics for unclassified packets is not turned on. Cisco 2811 (revision 49.46) with 251904K/10240K bytes of memory. Processor board ID FCZ121472H7 2 FastEthernet interfaces DRAM configuration is 64 bits wide with parity enabled. 239K bytes of non-volatile configuration memory. 3915760K bytes of USB Flash usbflash1 (Read/Write) 62720K bytes of ATA CompactFlash (Read/Write)
*Aug 1 22:08:36.067: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB d evice has been inserted in port 1. *Aug 1 22:08:36.183: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t o up *Aug 1 22:08:36.207: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state t
o up *Aug 1 22:08:36.755: %USBFLASH-5-CHANGE: usbflash1 has been inserted! *Aug 1 22:08:36.763: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values i n partition table or boot sector. Device needs formatting before use! *Aug 1 22:08:37.183: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/0, changed state to down *Aug 1 22:08:37.207: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/1, changed state to down *Aug 1 22:08:38.419: %SYS-5-CONFIG_I: Configured from memory by console *Aug 1 22:08:38.843: %SYS-5-RESTART: System restarted -Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 28-Nov-07 21:09 by stshen *Aug 1 22:08:38.843: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start *Aug 1 22:08:39.047: %SYS-6-BOOTTIME: Time taken to reboot after reload = 134 seconds *Aug 1 22:08:40.339: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Aug 1 22:08:40.355: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down