Escolar Documentos
Profissional Documentos
Cultura Documentos
15.74
PAGE I
THE FOLLOWING PRESENTS STANDARD UNIT PRICES FOR HOT TAPS. WORK PERFORMED ON A
HOTTAPPING A process for cutting holes in pressurized pipes, tanks, or vessels without interrupting service or loss of product. This permits new tieins into existing systems, the insertion ol metering devices, permanent or temporary bypasses and is the preparatory stage for line
plugging.
INFORMATIONNEEDED FOR HOT TAPS A. Tap size including ANSI flange rating of valve.
B.
L
2.
C
restrictions, if any.
See Page
D.
Tapping valves should be full round opening gate or ball valves with necessary ID to pass cutting tool.
ANGLE TAPPING
Any tap where the center line of the tapping nozzle is not perpendicular to the surface being tapped, as shown below. Contact
Contractor prior to welding for technical information on degree ofangulation and possible need of angle iron clip to anchor pilot drill.
lnc.
HOT TAPS
DIMENSIONS
These dimensions are based on opening valve, give full details.
15.74
90' (perpendicular) pipe taps. If other than 90' (perpendicular)
PAGE 2
Flange I'
l-114" ot
ANSI
Maximum
"4" Dimension 'rB" Dimension "C" Dimension Inches Minimum Inches Minimum Inches
Macbine
All
l-112"
All
2'
3 3
J
All
150# 300# 600# 150# 300# 600#
T-l0l
T-101
T-l0l
360 360 360 360 360
4 4 4
l9'
37" (6r', 35"
54" 78"
29"
4" 4'. 4" 8" 8" 8" 20' 20' 20' 24' 24" 24" 30" 30" 36'
42"
Dimensional limitations can, in many
se') 34', s8") 32', 56'1 32'(s6') 33" (57") 33'(s7") 30" (s4") 36" (60") 29" (s3') 33' s7") 34', 58") 32" s6')
35" (59")
60"
(104') 80" (104") 82" ( 106") 82" (10') 82" (106") 82" (106")
80" 84" (108") 7e" (103") 85" (109") 82" 82" |0"
002")
31'
3 3 3 3 3 3
660 (760) 60 (70) 660 (760) 660 (70) 60 (760) 660 (760) 60 (760) 660 (760) 660 (760) 660 (70)
3 3 3
31" 56"
t200 t200 200 200 200 200 200 200 200 200 200 200 200 200
200
*
59" 56"
s6'
56" 56"
6" 6" 6.
56'
56 56 56 56 56 56 56 56 56
s3"
*
48"
*
53"
50'
Contact Hot Tap Specialty Contractor for dimensions and sizes not listed.
lnc
HOT TAPS
15.74
PAGE
The data in this Account is based on Taps made into carbon steel pipe. When Taps are made into material other than carbon steel pipe such as cement lined pipe, transite cast iron, stainless steel and other alloys, plastic or fiberglass, additional information such as the thickness ofa cement lining or the hardness ofan alloy compared to carbon steel may be needed.
Blind Flange, Weld Cap And Large Diameter Tank Tapping Depending on the thickness ofthe object being tapped, a drip leg incorporated into
the tapping nozzlemay be required to disperse shavings from the cutting area.
Tapping Materials That Can Not Be y'elded Ifit is necessary to tap or plug a line that can not be welded such as cast iron, transite, or even carbon steel when welding is not permitted in the area, a bolt-on ftting can be used.
TAPPING FITTINGS Tapping Fittings are full-branch or reducing branch split tees designed for use with tapping machines. They are equipped with ANSI Class 150, 300, 600 weld neck flanges.
Typical Size-on-Size
Fitting
lnc.
Continued on following
HOT TAPS
SUBCONTRACT STANDARD UNIT PRICES
15-74
PAGE 4
Tap 2" or
3"
4', 6
8
Size (Inches)
less
Maximum
Per
6 4 4 3
J
Taps Day
Price For
Additional
(Same
Fint Tap
Taps Dav)
810 10
130
1,100
1.1
4s0
510
I,250
1,360
660
820 880 990 1,160 1,600
660
660 660 80
10
3 2 2 2 2 2 2
I,420
1,700
l2'
't4"
t6"
18"
8r0
970 1,120
20"
22', 24', 26',
3,200
3,000 3,500 3.600
I,140
1,170 1,240 1.290
1,300 1,300 1.300 1,700 1,800 2.300
28' 30'
32', 34', 36 42 48
3,700
3,800
4.r 00
Notes:
l.
2.
Hot Tap prices include all tapping equipment and one technician to provide technical supervision in the application and use of the tapping equipment. Prices are based on one Hot Tap 150#, 300#, 600# raised face flange with a lesser charge for additional Hot Taps ofthe same
size.
contractors warehouse and mileage costs will be charged to and from the job site. Allow $5.00 per mile for
4. Hot Tap prices do not include labor or material prices for valves,
gaskets, bolts, nuts, blind flanges, welding, hoisting equipment, scaffolding, small tools, or testing. Add for same, as required from Accounts: (a) Valves, Blind Flanges I 5-0 and \/elding
(b) Gaskets, Bolts and Nuts (c) Hoisting Equipment (d) Scaffolding
t5-72
t-20
r-40
5.
Contact Hot Tap Specialty Contractor for frm pricing for specific projects.
lnc.