Escolar Documentos
Profissional Documentos
Cultura Documentos
37
IEG-TC1 1/2 ELECTROMAGNETIC LEVEL INDICATORS WITH ONE OR
TWO CONTACTS AND 1/2” GAS CONNECTION IEG-TCMM 1/2
IEG-TC2 1/2
USE:
Made to ensure, with maximum safety, the minimum or
minimum and maximum levels of liquids in tanks, and hydraulic
CONNECTOR
power packs containing mineral oils with viscosity not higher CONNECTOR
THREADED PLUG than 80°E. and for all non-corrosive and inflammable liquids. THREADED PLUG
41
41
OPERATION:
1/2”GAS
When the float of the indicator encounters the Reed switch
B (MIN.35)
1/2”GAS
A
A
60mm
TUBE Ø7
connected to it.
25
25
1 2
3 2
41
41
B (MIN.35)
3/4”GAS
3/4”GAS OPERATION:
When the float of the indicator encounters the Reed switch at the
pre-established point, the contact activated by the magnet housed MAX. FLOAT
TUBE Ø7 in the float opens or closes, thus obtaining the possibility of sending
TUBE Ø7
electrical equipment connected to it.
FITTING:
The indicator must be fitted in the vertical position, on 3/4” GAS
MIN. FLOAT
FLOAT
thread hole; seal is guaranteed by an O-ring in the crown of the cap
in aluminium with hexagon head.
25
Ø21 H=21
The float must be at least 35 mm from ferrous surfaces (tank walls,
25
etc.).
T
IMPORTANT: CONNECTION:
To invert the contact from N.C. to N.O. just remove the bottom stop Connector CE 1 2
1 2
3 2
USE:
Made to ensure, with maximum safety, the minimum or and empty levels of liquids in tanks, and
hydraulic power packs containing mineral oils with viscosity not higher than 80°E. and for all non-
50
corrosive and inflammable liquids.
CONNECTOR
OPERATION:
NUT CH.22 When the float of the indicator encounters the Reed switch incorporated in the tube at the pre-
M18x1,5 established distances, the contact activated by the magnet housed in the float opens or closes, thus
BRASS TUBE Ø10
obtaining the possibility of sending a luminous or acoustic signal or disconnecting any electrical
equipment connected to it.
A
Ø30
FLOAT IN NYLON FITTING:
(SPANSIL OR
POLYPROPYLENE ON REQUEST)
The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous
44
The tight‘s flange is ensured by a flat synthetic rubber gasket and by a locking nut.
Since the diameter of the float is greater than the diameter of passage hole on the tank during
installation you must fix the gauge to the tank and replace the float.
1 2
3 2
USE:
Made to ensure, with maximum safety, the minimum or and empty levels of liquids in tanks, and
hydraulic power packs containing mineral oils with viscosity not higher than 80°E. and for all non-
50 corrosive and inflammable liquids.
50
CONNECTOR
OPERATION:
IEG-TQ10MM: when the float of the indicator encounters the Reed switch incorporated in the tube CONNECTOR
at the pre-established distances, the contact activated by the magnet housed in the float opens
NUT CH.22
or closes, thus obtaining the possibility of sending a luminous or acoustic signal or disconnecting NUT CH.22
M18x1,5
B (MIN.35)
The levels IEG-TQ10MV are used for having a double alarm signal at a pre-established distance.
MAX. FLOAT
The former is normally used to signal when the liquid is nearly finished; the latter can be used as
44
44
MIN. 70mm
B (MIN.35)
A
BRASS TUBE Ø10
BRASS TUBE Ø10
The contacts that are activated by a single float can be at least 25 mm apart. Also, the signals (in FLOAT
MIN. FLOAT absence of liquid ) can be activated (they close) consecutively or deactivated (they open). The EMPTY
same principle can be applied for the maximum level control (max. and extra max.).
35
35
Ø30
FITTING: Ø30
The indicator must be fitted in the vertical position, and the float must be at least 35mm from
ferrous surfaces (walls, tanks, etc.).
The tight‘s flange is ensured by a flat synthetic rubber gasket and by a locking nut. Since the
diameter of the float is greater than the diameter of passage hole on the tank during installation
you must fix the gauge to the tank and replace the float.
USE:
Made to ensure, with maximum safety, the minimum or and empty levels of liquids in tanks, and hydraulic
50
power packs containing mineral oils with viscosity not higher than 80°E. and for all non-corrosive and
CONNECTOR inflammable liquids.
FITTING:
FLOAT The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous
Ø21 h=21
surfaces (walls, tanks, etc.).
25
The tight‘s flange is ensured by a flat synthetic rubber gasket and by a locking nut. Since the diameter
of the float is greater than the diameter of passage hole on the tank during installation you must fix the
gauge to the tank and replace the float.
1 2
3 2
USE:
Made to ensure, with maximum safety, the minimum levels of liquids in tanks, and hydraulic power packs
50 containing mineral oils with viscosity not higher than 80°E. and for all non-corrosive and inflammable liquids.
CONNECTOR
OPERATION:
NUT CH.22 When the float of the indicator encounters the Reed switch incorporated in the tube at the pre-established
distances, the contact activated by the magnet housed in the float opens or closes, thus obtaining the possibility
B (MIN.35)
M18x1,5
of sending a luminous or acoustic signal or disconnecting any electrical equipment connected to it.
MAX. FLOAT
FITTING:
MIN. DISTANCE 60mm
A
TUBE Ø7 The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous surfaces
(walls, tanks, etc.).
MIN. FLOAT
The tight‘s flange is ensured by a flat synthetic rubber gasket and by a locking nut.
25
Since the diameter of the float is greater than the diameter of passage hole on the tank during installation you
must fix the gauge to the tank and replace the float.
PRESSURE
ELECTRICAL CHARACTERISTICS
TEMPERATURE
MAX.
ELECTRICAL
MODEL MATERIAL CONNECTION POWER POWER CURRENT
CONTACTS COMMUTABLE TEFLON
COMMUTABLE COMMUTABLE STRENGTH PROTECTION RANGE
VOLTAGE WIRES
IN D.C. IN A.C. IN A.C.
-20 +120°C
-20 +80°C
10 Bar
220 VDC
IEG - TQ07MM 18X1,5 BRASS M18 x 1,5 SPST 40 W 4 0 V.A. 2A IP 65
220 VAC
USE:
Made to ensure, with maximum safety, the minimum or and empty levels of liquids in tanks, and hydraulic
power packs containing mineral oils with viscosity not higher than 80°E. and for all non-corrosive and
CONNECTOR
inflammable liquids.
40
3/8” GAS
OPERATION:
When the float of the indicator encounters the Reed switch incorporated in the tube at the pre-established
distances, the contact activated by the magnet housed in the float opens or closes, thus obtaining the
possibility of sending a luminous or acoustic signal or disconnecting any electrical equipment connected to
A
ON REQUEST)
35
The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous surfaces
Ø30
(walls, tanks, etc.).
The tight‘s flange is ensured by a flat synthetic rubber gasket and by a locking nut.
Since the diameter of the float is greater than the diameter of passage hole on the tank during installation
you must fix the gauge to the tank and replace the float
1 2
3 2
USE:
Made to ensure, with maximum safety, the minimum or and empty levels of liquids in tanks,
and hydraulic power packs containing mineral oils with viscosity not higher than 80°E. and
for all non-corrosive and inflammable liquids.
CONNECTOR
OPERATION:
40
CONNECTOR
IEG-BTMM: when the float of the indicator encounters the Reed switch incorporated in the
40
3/8” GAS
tube at the pre-established distances, the contact activated by the magnet housed in the
B (MIN.35)
3/8” GAS
float opens or closes, thus obtaining the possibility of sending a luminous or acoustic signal
MAX. FLOAT
or disconnecting any electrical equipment connected to it.
44
44
The levels IEG-BTMV are used for having a double alarm signal at a pre-established distance. MINIMUM
MIN. 70mm
A
B (MIN.35)
A
The former is normally used to signal when the liquid is nearly finished; the latter can be BRASS TUBE Ø10
35
Ø30
signals (in absence of liquid ) can be activated (they close) consecutively or deactivated
Ø30
(they open).
The same principle can be applied for the maximum level control (max. and extra max.).
FITTING:
The indicator must be fitted in the vertical position, and the float must be at least 35mm
from ferrous surfaces (walls, tanks, etc.). Since the diameter of the float is greater than the
diameter of passage hole on the tank during installation you must fix the gauge to the tank
and replace the float.
48
Suitable for tanks containing liquids compatible with the brass
tube, such as hydraulic and lubricant oils (with density not higher
1”GAS
than 80°E), petroleum, etc. 1”GAS
B (MIN.40)
BRASS TUBE Ø10
OPERATION:
MIN. DISTANCE 70
pre-established point, the contact activated by the magnet housed
A
Ø30
NYLON FLOAT in the float opens or closes, thus obtaining the possibility of sending BRASS TUBE Ø10
(SPANSIL-POLYPROPYLENE a luminous or acoustic signal or activating or disconnecting any
A
ON REQUEST)
electrical equipment connected to it. FLOAT
44
Ø30 H=44
35
FITTING:
35
The indicator must be fitted in the vertical position, and the float
must be at least 35mm from ferrous surfaces (walls, tanks, etc.).
NB:
The IEG - TCMM level indicator with SPDT (exchange) separate
CONNECTION:
T
contacts or with one common, requires an aluminium connection
Connector CE 1 2
head containing an adequate number of terminals for the use (5 or
DIN 43650 IP65 PG.9 3
6).
1 2
3 2
1
48
FIXING FLANGE maximum level (IEG - N1F / N2F) or minimum and maximum SEAL
48
B (MIN. 35)
Suitable for tanks containing liquids compatible with the
brass tube, such as hydraulic and lubricant oils (with density
BRASS TUBE Ø10 not higher than 80°E), petroleum, etc. MAX. FLOAT
OPERATION:
44
When the float of the indicator encounters the Reed switch BRASS TUBE Ø10
A
at the pre-established point, the contact activated by the
A
35
connected to it.
35
Ø30
FITTING:
The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous surfaces (walls,
tanks, etc.).
Flange seal is guaranteed by an oilproof synthetic rubber seal (neoprene). CONNECTION: T
NB: Connector CE 1 2
The IEG - TCMM level indicator with SPDT (exchange) separate contacts or with one common, requires an aluminium DIN 43650 IP65 PG.9 3
connection head containing an adequate number of terminals for the use (5 or 6).
1 2
M4
Ø35,2
Ø42
120° 3 2
Ø55
tanks and hydraulic power packs containing mineral oils with viscosity not higher than
80°E; also suitable for gas oil and other non-corrosive and inflammable liquids.
50
B min=80
OPERATION: 48
When the float of the indicator encounters the Reed switch at the pre-established point,
44
A=ON REQUEST
the contact activated by the magnet housed in the float opens or closes, thus obtaining
BRASS TUBE Ø10
the possibility of sending a luminous or acoustic signal or activating or disconnecting
any electrical equipment connected to it.
FITTING:
35
FIXING FLANGE
SEAL
CONNECTOR Fitting on the side of the tank allows installation of the Level when there is no room Ø30
for it on the cover and, above all, when the place where the control unit is fitted is so
Ø55
narrow as to make fitting/removal of a level indicator fixed on the cover impossible. CONNECTION:
50
Connector CE
A=102 (MINIMUM POSSIBLE)
1 2
two provided for by the GMMF version; in this case the connection head must be in
35
1 2
M4
Ø35,2
Ø42
120°
3 2
1
CONNECTOR
Made to ensure, with maximum safety, the minimum or maximum CONNECTOR
level of liquids in tanks and hydraulic power packs containing
50
50
BASE mineral oils with viscosity not higher than 80°E; also suitable for gas BASE
oil and all other non-corrosive and inflammable liquids.
FIXING FLANGE OPERATION: FIXING CLAMP
CLAMPING GRUB SCREW
When it is necessary to vary the minimum or maximum position,
A-MAXIMUM LENGTH ON REQUEST
20
Ø55 on the connection enough for the required variation in opening/ 20 17
85
closing of the Reed switch incorporated in the tube. In this way it
FIXING GRUB SCREW BRASS TUBE Ø10
BRASS TUBE Ø10 is possible to vary the activation position of a luminous or acoustic
signal or disconnect any electrical equipment connected to it.
FITTING:
44
The indicator must be fitted in the vertical position. The float must
44
35
35
Ø30
Ø30
IMPORTANT:
To invert the contact from N.C. to N.O. just remove the bottom stop and turn the float upside down. T
POSSIBILITIES: CONNECTION:
The useful measurements controllable by the variable length level indicator go from a minimum of 40mm Connector CE 1 2
from the connection support surface to a maximum defined by the user. The stainless steel version can also DIN 43650 IP65 PG.9 3
be supplied on request.
M4 1 2
Ø35,2
Ø42
3 2
120°
1
48
SEAL viscosity not higher than 80°E. and for all non-corrosive and inflammable
liquids.
Ø55
1”GAS
BRASS TUBE Ø10 OPERATION:
BRASS TUBE Ø10
The minimum and empty level indicators are used for having a double
alarm signal at a pre-established distance. The former is normally used to
44
MINIMUM signal when the liquid is nearly finished; the latter can be used as a machine
A
MINIMUM
stop, etc. The contacts that are activated by a single float can be at least 25
44
A
B (MIN.25)
mm apart. Also, the signals (in absence of liquid ) can be activated (they
B (MIN.25)
FLOAT
close) consecutively or deactivated (they open). The same principle can be
applied for the maximum level control (max. and extra max.).
EMPTY
EMPTY
FITTING:
35
The indicator must be fitted in the vertical position, and the float must
35
Ø30 be at least 35mm from ferrous surfaces (walls, tanks, etc.). Flange seal is Ø30
guaranteed by an oilproof synthetic rubber seal for IEG - MVF and O-ring
for IEG - MVT.
T
IMPORTANT: CONNECTION:
Due to the particular type of construction, these level indicators do not have reversible contacts, therefore when Connector CE
1 2
ordering it is necessary to request N.C. or N.O. contacts. (in absence of liquid). DIN 43650 IP65 PG.9 3
The two versions entirely in AISI 316 stainless steel can be obtained on request.
M4
Ø35,2
Ø42
120°
SEAL
LEVEL INDICATOR OPERATION:
When the float of the indicator encounters the Reed switch at the pre-established point, the contact activated by
Ø55
the magnet housed in the float opens or closes, thus obtaining the possibility of sending a luminous or acoustic
signal or activating or disconnecting any electrical equipment connected to it.
BRASS TUBE
THERMOSTAT OPERATION:
When the temperature of the liquid in the tank reaches the
thermostat setting value, the thermostat closes or opens for
A
1= THERMOSTAT
switching on a lamp or interrupting operation of the machine 2= ELECTRIC LEVEL INDICATOR T
connected to it, or activating any cooling equipment, thus 3= COMMON
4= EARTH 1 2
preventing the risk of overheating and permanent damage. Connection:
FITTING:
44
Connector CE 3
38
M4
Ø35,2
Ø42
2 3
120°
CONNECTOR
Made to ensure, with maximum safety, the minimum or maximum CONNECTOR
48 FIXING FLANGE level of liquids in tanks (even under pressure at 10 bar) and hydraulic FIXING FLANGE
48
SEAL power packs containing mineral oils with viscosity not higher SEAL
than 80°E; also suitable for gas oil and all other non-corrosive and
THREADED UNION inflammable liquids. THREADED UNION
Ø55 Ø55
BRASS TUBE Ø10
OPERATION:
When the float of the indicator encounters the Reed switch at the S/STEEL TUBE Ø7
pre-established point, the contact activated by the magnet housed
in the float opens or closes, thus obtaining the possibility of sending
A
21
long (IEG-U1F/U2F) and 500/450 mm long (IEG-UMMF). The required
44
35
length can thus be obtained with the aid of an ordinary pipe cutter. Ø21
Ø30
Insert the wires and tube in the threaded union located under the flange, then suitable tighten for perfect assembly. Connect
the connector to the flange and the respective wires to the base, and the level indicator is ready to use.
FITTING ON THE TANK:
CONNECTION:
T
The indicator must be fitted in the vertical position, and the float must be at least 35mm from ferrous surfaces (walls, tanks,
Connector CE 1 2
etc.).
DIN 43650 IP65 PG.9 3
IMPORTANT:
To invert the contact from N.C. to N.O. just remove the bottom stop and turn the float upside down.
M4
Ø35,2
Ø42
120°
ELECTRICAL CONNECTION
USE:
Built to ensure maximum security with the different
control points in the tanks, hydraulic power packs
PROCESS CONNECTION
that contain mineral oils with a viscosity above 80 ° E,
also suitable for diesel and other non-corrosive and
MIN. 35
STOP
L
flammable liquids.
I
FLOAT
OPERATION:
H
BRASS TUBE
When the float of the indicator encounters the Reed
switch at the pre-established point, the contact
G
activated by the magnet housed in the float opens
F
or closes, thus obtaining the possibility of sending
E
a luminous or acoustic signal or activating or
disconnecting any electrical equipment connected to
D
it.
C
MIN. 35
FITTING:
B
The indicator must be fitted in the vertical position, and
A
the float must be at least 35mm from ferrous surfaces
(walls, tanks, etc.).
A B C D A B C D 1 IP65
ALUMINIUM HEAD 2 IP65
ALUMINIUM HEAD
Ø5 Ø5 Ø6.4
Ø5.5 70
20
100
44
80
Ø30
Ø42 Ø42 Ø60.3 Ø79.5
Ø55 Ø55 Ø70 Ø100 Ø30 100
50
ELECTRICAL CONNECTION
USE:
Made to ensure, with maximum safety, the minimum or maximum level of liquids
PROCESS CONNECTION in tanks containing corrosive substances.
48
Entirely in AISI 316 stainless steel, they are suitable for use in the chemical,
pharmaceutical and food industries.
OPERATION:
B
When the float of the indicator meets the Reed switch incorporated in the tube at
FLOAT OF MAX. LEVEL the pre-established
distances, the contact is activated by the magnet housed in the float opens or
closes, thus obtaining the possibility of sending a luminous or acoustic signal or
C
TUBE
FITTING:
The indicator must be fitted in the vertical position, and the float must be at least
FLOAT OF MIN. LEVEL 35mm from ferrous surfaces (walls, tanks, etc.). Flange seal is guaranteed by an
oilproof synthetic rubber seal.
X
A B C D 1 IP65
ALUMINIUM HEAD 2 IP65
ALUMINIUM HEAD
70
100
44
36
52
52
80
Ø30
Ø30 Ø44.5
Ø52 100
50
USE:
ELECTRICAL CONNECTION Made to ensure, with maximum safety, the minimum or maximum level of liquids in
PROCESS CONNECTION tanks containing corrosive substances.
48 GASKET Entirely in AISI 316 stainless steel, they are suitable for use in the chemical,
pharmaceutical and food industries.
B
OPERATION:
When the float of the indicator meets the Reed switch incorporated in the tube at
FLOAT OF MAX. LEVEL
the pre-established
distances, the contact is activated by the magnet housed in the float opens or
closes, thus obtaining the possibility of sending a luminous or acoustic signal or
C
A
TUBE
disconnecting any electrical equipment connected to it.
FITTING:
FLOAT OF MIN. LEVEL The indicator must be fitted in the vertical position, and the float must be at least
35mm from ferrous surfaces (walls, tanks, etc.). Flange seal is guaranteed by an
oilproof synthetic rubber seal.
X
Ø70
70
Ø5 Ø5
Ø60+-01
100
44
40
52
52
80
.5 Ø30
Ø42 Ø4 Ø34 Ø44.5
Ø42
Ø55 Ø55 Ø52 100
120°
USE:
Made to detect, with maximum safety, the level of
liquids in tanks containing corrosive substances.
ELECTRICAL CONNECTION
Entirely in AISI 316 stainless steel, they are suitable
for use in the chemical, pharmaceutical and food
INOX PROCESS CONNECTION
industries.
STOP
L
OPERATION:
When the float of the indicator encounters the Reed
I
switch at the pre-established point, the contact
INOX TUBE
H
G activated by the magnet housed in the float opens
or closes, thus obtaining the possibility of sending
a luminous or acoustic signal or activating or
INOX FLOAT
F
FITTING:
C
Ø70
70
Ø5 Ø5
Ø60+-01
100
44
36
40
52
52
80
Ø30
.5 Ø30
Ø42 Ø4 Ø34 Ø44.5
Ø42
Ø55 Ø55 Ø52 100
120°
the contacts are activated by the magnet housed in the fl oat COD:5056001
and open or close, thus obtaining the possibility of sending a
luminous or acoustic signal or activating or disconnecting any
A
USE:
The Levels electromagnetic reed-chain resistors Indicators allow a precise and
constant indication of the fluid level, regardless of its electrical conductivity, pressure
and temperature and by the presence of foam in it; essentially they have a simple
MS F
structure, since the only moving part is the float which, depending on the flow or
drain the liquid, flows through a tube. ELECTRICAL CONNECTION
FITTING PROCESS
OPERATION:
The floating stay within a toroidal magnet, whose field operates, without physical STOP
contact, small reed contacts placed inside the pipe flow (see Fig.1). The drive of these
contacts allows the integration or gradual shutdown of the resistance, also placed
L
inside the pipe flow, allowing the continuous reading of liquid level.
C
TUBE
Resistive signal thus generated can be directly used by devices that accept inputs
well structured, or through a converter Ohm - 4/20mA can drive most of the
electronic devices on the market (PLC). FLOAT
TECHNICAL ADVANTAGES:
- Constant and continuous indication of the level with high accuracy of repeatability.
- Linear index of the level, regardless of the shape of the tank and the distance
MI
PITCH
FOR CONNECTIONS 3-4-5-6-7-8-12-13
C= MAX CONTROL FIELD
C= L-MI-MS RESISTANCE
5 6 7 8 12 13 A B C D
Ø5 Ø5 Ø6.4 Ø5
Ø5.5 Ø4.5
52
44
20
52
Ø42 Ø42 Ø60.3 Ø79.5 Ø42 Ø60 Ø30 Ø30 Ø44.5 Ø52
Ø55 Ø55 Ø70 Ø100 Ø55 Ø70
1/2
24
0 1
80
48 Ø59
31
80
58
48 Ø59
USE:
Made to detect, with maximum safety, the level of liquids in
tanks containing corrosive substances. Suitable in chemical ELECTRICAL CONNECTION
industry, for their realization totally in PVC. 1/2 “ GAS
12
Can be controlled from 1 to a maximum of 4 points with
30
CH. 27
15
SPST contacts.
PVC PROCESS CONNECTION
OPERATION:
When the float of the indicator encounters the Reed switch STOP IN PVC
at the pre-established point, the contact activated by the
magnet housed in the float opens or closes, thus obtaining
E
MIN: 70mm
or activating or disconnecting any electrical equipment
D
connected to it.
C
FITTING:
B
float must be at least 35mm from ferrous surfaces (walls, FLOAT IN PVC Ø44,5 x 42
tanks, etc.).
NB: the one shown in this drawing is only one version. TUBE IN PVC Ø12
Number of contacts and lengths are always performed at
the request of the customer.
USE:
The Levels electromagnetic reed-chain resistors Indicators ELECTRICAL CONNECTION
OPERATION:
PVC TUBE Ø12
The float stay within a toroidal magnet, whose field
operates, without physical contact, small reed contacts
placed inside the pipe flow (see Fig.1). The drive of these
C
contacts allows the integration or gradual shutdown of the PVC FLOAT Ø44,5 x 42
resistance, also placed inside the pipe flow, allowing the
continuous reading of liquid level.
Resistive signal thus generated can be directly used by
devices that accept inputs so structured, or through a
converter Ohm - 4/20mA can drive most of the electronic
devices on the market (PLC).
MI
PVC STOP
TECHNICAL ADVANTAGES:
- Constant and continuous indication of the level with
high accuracy of repeatability. FIG.1
- Linear indication of the level, regardless of the shape of REED
the tank and the distance between gauge and the tank PITCH
walls.
- Remote indication of the measure and possibility of
piloting of additional controls. RESISTANCE
ELECTRICAL CONNECTIONS
ALUMINIUM ALUMINIUM
A IP65 HEAD B IP65 HEAD 1 DIGITAL DISPLAY
2 ADJUSTABLE ALARMS 20...53 Vac/Vdc 2 ANALOG DISPLAY
DEPTH: 50mm
DEPTH: 100 mm
75 70
1/2
24
0 1
80
80
58
48 Ø59
USE:
Made to detect, with maximum safety, the level of liquids in
tanks containing corrosive substances.
Suitable in chemical industry, for their realization totally in ELECTRICAL CONNECTION
PVC.
Can be controlled from 1 to a maximum of 9 points with
L SPST contacts.
I
H
PVC STOP
D
connected to it.
A
ELECTRICAL CONNECTION
ALUMINIUM HEAD
A IP65 B ALUMINIUM HEAD
IP65
70
100
80
100