Escolar Documentos
Profissional Documentos
Cultura Documentos
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 1
ARMOR SPECIFICATIONS
Protection on all sides to Level A10 Protection against high power rifles such as: 7.62x39, 5.56x45, .03-06 and 7.62x51 rounds OPAQUE (AR 500 Steel): 0.50 in thick TRANSPARENT (Glass/Polycarbonate): 55 mm thick Seating- two seats up front, bench seating for 4 in rear, 2" padded seat and backs Special LED Red and Blue lights White LED dome lights for the Interior Armored Dual battery compartment Running boards with grab handles Rear door opening 6', 8" long and 33" wide Insulation on all walls and ceiling (2") Recording equipment for all cameras Under seat compartments 3 Outside storage cabinets Removable Plow Control Revolving Water Cannon Revolving Camera on rooftop 2 Gun Ports on each side of the front cabin P/A System with siren
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 2
GO LIGHTS
INSTRUCTIONS
Operations of Stryker Using the remote control, turn on the light by depressing the on/off button With the 4-way arrows on the remote control, rotate your light to the desired location. Depending upon conditions, the wireless remote may be used up to 100 feet from the Stryker. The speed of the light rotation can be controlled by depressing the fast/slow button one time and by depressing it again to restore the original speed. The spotlight should not be turned on when the snap on lens (rockguard) is attached. BULB REPLACEMENT The Golight Stryker utilizes a Philips 9011 bulb IMPORTANT INFORMATION This Golight Stryker is a radio transmitter and receiver operating at 433mhz. Whenever the light is on, the internally mounted antenna sends out and receives radio frequency (RF) energy. PROGRAMMABLE REMOTE INSTRUCTIONS The Golight Stryker is controlled with a programmable remote with 6561 different channels. This feature allows you freedom to change the channel selection, & the receiver relearns the new selection. * Click here to view PDF link
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 3
RED/BLUE LIGHTS
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 4
PLOW CONTROLS
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 5
CONTROL BOX
PUBLIC ADRESS SYSTEM WITH MULTI-MODE SIREN
Two manual functions allow for additional siren tone choices when you need it the most. PTT (push to talk) switch on microphone overrides all siren functions. Combination On/Off and horn ring transfer switch. Pre-wired unidirectional microphone. Optional plug-in microphone with volume control knob. Adjustable preset microphone volume. Adjustable preset radio repeat volume. Input polarity protection. Output short circuit protection. External spade-type fuse. Bi-polarity horn/ring control activation. "Aux Enable" activates Siren tones via input (slide switch, power controls or relay-to-ground connection). Quick disconnect plug for ease of service or replacement. Adjustable bail bracket allows the mounting of the siren in a variety of positions. Complements all Whelen's under dash products. Backward compatible to the original 295HF100 and WS2100 Series connector. Optional 24 volt DC model available, contact factory.
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 6
CAMERA SYSTEM
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 7
WATER CANNON
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 8
CONTROL BOX
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 9
CONTROL BOX
Tel: +1.703.471.0002
Fax: +1.703.471.0202
www.alpineco.com
armor@alpineco.com
Page 10
INSTALLATION IN TIRE
Insert arcs into the tire with the flanges and washers facing up. Apply supplied loctite to one bolt. Connect arcs loosely with one bolt Fit inboard tire bead on wheel and allow CRF to move into wheels drop center With outboard tire bead above the wheel flange, place steel mounting rods vertically in holes on each side of CRF joint. Rotate CRF until the joint is centered over the valve Slip adjustment band over mounting rods. Laterally spread the rods at top closing the CRF. Apply loctite on the remaining bolt and tighten ALL bolts to 30 +/- 5 ft.lbs Secure mechanical lock over all connection bolts. Attached with #2 phillips head screw driver. Mount outer tire bead and inflate to manufacturers recommended pressure for load carried.
Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com armor@alpineco.com Page 11