Escolar Documentos
Profissional Documentos
Cultura Documentos
As Required by the Provisions of the ASME Code Rules, Section VIII, Division 2
1. Manufactured and certified by
(Name and address of manufacturer)
2. Manufactured for
(Name and address of purchaser)
3. Location of installation
(Name and address)
4. Type
Horiz. or vert. tank Mfr.s Serial No. CRN Drawing No. Natl. Bd. No. Year built
5. The chemical and physical properties of all parts meet the requirements of material specifications of the ASME BOILER AND PRESSURE VESSEL CODE. The design, construction, and workmanship conform to ASME Code, Section VIII, Division 2
Year Addenda date Code Case No. Drawing No. Drawing prepared by Service Description of part inspected
6. Constructed to:
Items 7 to 12 incl. to be completed for single wall vessels, jackets of jacketed vessels, or shells of heat exchangers
7. Shell
Material (Spec. No., Grade) Nom. thk. (in.) Corr. allow. (in.) Inside diameter (ft & in.) Heat treatment Heat treatment Radiographic treatment Length (overall) (ft & in.) Radiographic treatment No. of courses Spec. No., Grade
8. Seams
Longitudinal Girth
(b) Matl.
Minimum Thickness
Corrosion Allowance
Crown Radius
Knuckle Radius
Elliptical Ratio
Hemispherical Radius
Flat Diameter
If bolted, describe or sketch. F. Charpy impact psi. Fatigue analysis required ft-lb .
Yes or no
12. Design press. psi at max. temp. F. Min. design metal temp. at test temp. of Pneu., hydro., or comb. test pressure psi.
F at
14. Tubes
Matl. (Spec. No., Grade)
Items 15 to 18 incl. to be completed for inner chambers of jacketed vessels or channels of heat exchangers
15. Shell
Matl. (Spec. No., Grade) Nom. thk. (in.) Corr. allow. (in.) Inside diameter (ft & in.) Length (overall) (ft & in.) Radiographic treatment No. of courses Spec. No., Grade
16. Seams
Longitudinal (wld., dbl., singl.) Girth Heat treatment Heat treatment (yes or no) Radiographic treatment
(b) Matl.
Minimum Thickness Corrosion Allowance Crown Radius Knuckle Radius Elliptical Ratio Conical Apex Angle Hemispherical Radius Flat Diameter Side to Pressure (Convex or Concave)
F. Charpy impact F at
This Form (E00114) may be obtained from ASME, Order Dept, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300
E00114
Lugs
No.
Legs
No.
Other
Describe
Attached
Where and how
22. Remarks
CERTIFICATION OF DESIGN Users Design Specification on file at Manufacturers Design Report on file at Users Design Specification certified by Manufacturers Design Report certified by
We certify that the statements made in this report are correct and that all details of material, construction, and workmanship of this vessel conform to the ASME Code for Pressure Vessels, Section VIII, Division 2. U2 Certificate of Authorization No. expires Date Co. name
Manufacturer
. Signed
Representative
CERTIFICATE OF SHOP INSPECTION I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and/or the State or Province of of Report on , and employed by , have inspected the part of a pressure vessel described in this Manufacturers Data and state that, to the best of my knowledge and belief, the Manufacturer has constructed this
part in accordance with the ASME Code, Section VIII, Division 2. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the part described in the Manufacturers Data Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection. Date Signed
Authorized Inspector
Commissions
Natl Board (incl. endorsements), State, Prov., and No.