Escolar Documentos
Profissional Documentos
Cultura Documentos
Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice The purchased products, services and features are stipulated by the commercial contract made between Huawei and the customer. All or partial products, services and features described in this document may not be within the purchased scope or the usage scope. Unless otherwise agreed by the contract, all statements, information, and recommendations in this document are provided AS IS without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
Cont ents
Contents
1 Introduction ................................................................................................................................ 1-1
1.1 Scope ................................................................................................................................. 1-1 1.2 Int ended Audience ............................................................................................................... 1-1 1.3 Change History.................................................................................................................... 1-1
7 Parameters ................................................................................................................................. 7-1 8 Counters...................................................................................................................................... 8-1 9 Glossary ...................................................................................................................................... 9-1 10 Reference Documents ......................................................................................................... 10-1
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
ii
1 Introduction
1 Introduction
1.1 Scope
This document describes the principles of implementing enhanced EDGE coverage on DTRX and multi-carrier TRX, scenarios where enhanced EDGE coverage is applied, and engineering guidelines regarding enhanced EDGE coverage. The feature involved is GBFD-118104 Enhanced EDGE Coverage.
Personnel working on Huawei GSM products or systems System operators who need a general understanding of this feature
Feature change Feature change refers to the change in the enhanced EDGE coverage feature of a specific product version.
Editorial change Editorial change refers to the change in wording or the addition of the information that was not described in the earlier version.
Document Issues
The document issues are as follows:
01 (2011-03-31)
This is the first release of GBSS13.0. Compared with issue Draft A (2011-01-15) of GBSS13.0, issue 01 (2011-03-31) of GBSS13.0 has no change.
Draft A (2011-01-15)
This is the draft release of GBSS13.0. Compared with issue 01 (2010-06-30) of GBSS12.0, issue Draft A (2011-01-15) of GBSS13.0 has no change.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
1-1
Increasing the network coverage so that the coverage area of high -rate PS services is almost the same as that of CS services. Increasing the transmit power. The C/I of calls is improved. In this way, a higher-order modulation scheme can be used to increase the uplink and downlink data rate.
Double-transceiver series base stations DTRUs and DTRMs of BTS3012, BTS3012II, BTS3012AE, BTS3006C, and BTS3002E 3900 series base stations DBS3900, BTS3900, BTS3900A, BTS3900L, and BTS3900E
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
2-1
3 DTRX
3 DTRX
3.1 Principles
If HIGHMODPWREN is set to ALLOWED, enhanced EDGE coverage is enabled. In this case, the maximum output power of the TRX is increased by the value specified by UPGRADELEV8PSK. If the BCCH TRX is to be enabled with enhanced EDGE coverage, MAINBCCHHIGHMODPWREN should be set to ALLOWED. In this manner, the maximum output power of the BCCH TRX is increased by the value specified by UPGRADELEV8PSK. For the DTRX, if one of the two carriers that belong to the same cell and DTRX is idle at a transmit moment, then PS services are transmitted by the two carriers at the same time. That is, dynamic transmit diversity or dynamic PBT is used to transmit PS services. In this case, the maximum output power of high-rate PS services can reach to a level as that of CS services when the DTRX is in separated or combined transmit mode.
For details about dynamic transmit diversity, see Transmit Diversity Feature Parameter Description . For details about dynamic PBT, see PBT Feature Parameter Description.
A DRRU is used in distributed base stations. The transmit and receive mode of a DRRU is specified by SndRcvMode . A DRFU is used in outdoor and indoor macro base stations. The transmit and receive mode of a DRFU is specified by SndRcvMode1 .
Table 3-1 Enhanced EDGE coverage of a DTRX for 3900 series base stations Transmit and Receive Mode Single Feeder[1TX + 1RX] Single Feeder[1TX + 2RX] Double Feeder[2TX + 2RX] Double Feeder[2TX + 4RX] Double Feeder[1TX + 1RX] Double Feeder[1TX + 2RX]
Issue 01 (2011-03-31)
Implementation Mode Dynamic PBT Dynamic PBT Dynamic transmit diversity Dynamic transmit diversity Dynamic PBT Dynamic PBT
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd. 3-1
3 DTRX
The implementation modes of enhanced EDGE coverage of a DTRX vary according to the SNDMD of Huawei double-transceiver series base stations, as listed in Table 3-2. Table 3-2 Enhanced EDGE coverage of a DTRX for double-transceiver series base stations Transmit and Receive Mode No Combination Wideband Combination Dynamic Transmit Diversity DPBT Implementation Mode Dynamic PBT Dynamic transmit diversity Dynamic transmit diversity Dynamic PBT
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
3-2
4 Multi-Carrier TRX
4 Multi-Carrier TRX
4.1 Principles
If HIGHMODPWREN is set to ALLOWED, enhanced EDGE coverage is enabled. In this case, the maximum output power of the TRX is increased by the value specified by UPGRADELEV8PSK. If the BCCH TRX is to be enabled with enhanced EDGE coverage, MAINBCCHHIGHMODPWREN should be set to ALLOWED and the maximum output power of the BCCH TRX is increased by the value specified by UPGRADELEV8PSK. For a multi-carrier TRX, output power is shared among multiple TRXs so that the transmit power of TRX in 8PSK modulation scheme is increased. The power amplifier of a multi-carrier TRX does not transmit signals at full power in most cases due to power control or due to no traffic in some timeslots. In this case, power margin exists. If the power margin is used by other 8PSK traffic channels on the same timeslot, the maximum output power of the multi-carrier TRX in 8PSK modulation scheme may reach that of the multi-carrier TRX in GMSK modulation scheme.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
4-1
5 Related Feature
5 Related Feature
5.1 Frequency Hopping
Both DTRX and multi-carrier TRX support enhanced EDGE coverage when frequency hopping (FH), RF FH, and baseband FH are not enabled.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
5-1
6 Engineering Guidelines
6 Engineering Guidelines
6.1 DTRX
6.1.1 Cell Configuration S2 or Lower
When a cell is in S2 configuration mode, a BCCH TRX can be enabled with enhanced EDGE coverage, as shown in Figure 6-1. A non-BCCH TRX cannot be enabled with enhanced EDGE coverage because it cannot transmit signals at full power. Figure 6-1 DTRX with cell configuration S2
When a cell is in S1 configuration mode, one TRX works and another TRX is idle, as shown in Figure 6-2. The power amplifier of the idle TRX is power off out of power saving. Therefore, enhanced EDGE coverage cannot be enabled in this scenario. Figure 6-2 DTRX with cell configuration S1
When a cell is in S2 or lower configuration mode, one of the TRXs of each DTRX serves a cell, as shown in Figure 6-3. The two TRXs of the same DTRX belong to different cells, and thus dynamic PBT or dynamic transmit diversity cannot be enabled. Therefore, enhanced EDGE coverage cannot be enabled in this scenario.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
6-1
6 Engineering Guidelines
Figure 6-3 DTRX with cell configuration S2 or lower and TRX shared by another cell
If the BCCH DTRX is configured with only one TRX and the other DTRX is config ured with two non-BCCH TRXs, then both the BCCH TRX and non-BCCH TRXs can be enabled with dynamic PBT or dynamic transmit diversity. Thus, enhanced EDGE coverage can be enabled. If the BCCH DTRX is configured with two TRXs and the other DTRX is configured with one non-BCCH TRX, then only the BCCH TRXs can be enabled with enhanced EDGE coverage because they can be enabled with dynamic PBT or dynamic transmit diversity. The non-BCCH TRX on the BCCH DTRX and the non-BCCH TRX on the other DTRX cannot be enabled with enhanced EDGE coverage because they cannot be enabled with dynamic PBT or dynamic transmit diversity.
When a cell is in S3 configuration mode, two DTRXs are configured and one of them serve two cells, as shown in Figure 6-5.
If the BCCH TRX is configured on a DTRX that is shared by another cell, then the non -BCCH TRXs on the other DTRX can be enabled with dynamic PBT or dynamic transmit diversity, and thus enhanced EDGE coverage can be enabled. If the BCCH TRX is configured on a DTRX whose two TRXs serve the same cell, the BCCH TRX can be enabled with dynamic PBT or dynamic transmit diversity, and thus enhanced EDGE coverage can
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
6-2
6 Engineering Guidelines
be enabled. Neither the two non-BCCH TRXs can be enabled with dynamic PBT or dynamic transmit diversity. Thus, enhanced EDGE coverage cannot be enabled. Figure 6-5 DTRX with cell configuration S3 and TRX shared by another cell
6 Engineering Guidelines
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
6-4
7 Parameters
7 Parameters
Table 7-1 Parameter description Parameter ID NE MML Command Description
EDGEPWREN BSC6900 SET Meaning: Whether to enable the Enhanced EDGE Coverage GCELLBASICPARA( feature. Optional) GUI Value Range: NOT_ALLOWED(Not Allowed), ALLOWED(Allowed) Actual Value Range: NOT_ALLOWED, ALLOWED Default Value: NOT_ALLOWED HIGHMODPW BSC6900 SET Meaning: Whether to enable the high-order modulation power REN GCELLBASICPARA( increase function in a cell. In the case of a multi-transceiver Optional) unit, multiple TRXs may share one channel. If the total output power of the TRXs is lower than the maximum allowed transmit power of the channel at a time point, the remaining power can be used to increase the transmit power of a service in a high-order modulation scheme. In this manner, the transmit power in a high-order modulation scheme is comparable to the transmit power in GMSK. In the case of a double-transceiver unit, the two transmit channels can be used to increase the transmit power. GUI Value Range: NOT_ALLOWED(Not Allowed), ALLOWED(Allowed) Actual Value Range: NOT_ALLOWED, ALLOWED Default Value: NOT_ALLOWED MAINBCCHHI BSC6900 SET Meaning: Whether a service in a high-order modulation GHMODPWR GCELLBASICPARA( scheme on the BCCH TRX can use the high-order modulation EN Optional) power increase function when the function is enabled in the cell. GUI Value Range: NOT_ALLOWED(Not Allowed), ALLOWED(Allowed) Actual Value Range: NOT_ALLOWED, ALLOWED Default Value: NOT_ALLOWED POWT BSC6900 SET Meaning: This parameter specifies the maximum transmit GTRXDEV(Optional) power supported by the power amplifier of the TRX. The macro BTS and the mini BTS support different power levels. GUI Value Range: 80W(80W), 63W(63W), 60W(60W), 55W(55W), 50W(50W), 45W(45W), 40W(40W), 31W(31W), 30W(30W), 27W(27W), 26W(26W), 25W(25W), 24W(24W), 21W(21W), 20W(20W), 19W(19W), 18W(18W), 17W(17W), 16W(16W), 15W(15W), 14W(14W), 13_3W(13.3W), 13W(13W), 12_5W(12.5W), 12W(12W), 11_5W(11.5W), 11W(11W), 10W(10W), 9_5W(9.5W), 9W(9W), 8_5W(8.5W), 8W(8W), 7_5W(7.5W), 7W(7W), 6_5W(6.5W), 6W(6W), 5_5W(5.5W), 5W(5W), 4_5W(4.5W), 4W(4W), 3_7W(3.7W), 3_1W(3.1W), 3W(3W), 2_5W(2.5W), 2W(2W), 200mW(200mW), DEFAULT(Default)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd. 7-1
Issue 01 (2011-03-31)
7 Parameters
Parameter ID NE
MML Command
Description Actual Value Range: 80W, 63W, 60W, 55W, 50W, 45W, 40W, 31W, 30W, 27W, 26W, 25W, 24W, 21W, 20W, 19W, 18W, 17W, 16W, 15W, 14W, 13_3W, 13W, 12_5W, 12W, 11_5W, 11W, 10W, 9_5W, 9W, 8_5W, 8W, 7_5W, 7W, 6_5W, 6W, 5_5W, 5W, 4_5W, 4W, 3_7W, 3_1W, 3W, 2_5W, 2W, 200mW, DEFAULT Default Value: DEFAULT
PWRSPNR
BSC6900 SET Meaning: Finetune of the TRX power. During the static finetune GTRXDEV(Optional) of the TRX power, the BSC adjusts the TRX power at a step of 0.2 dB. In some scenarios, the losses vary depending on the tributaries where the power is combined, and the power difference before and after the power output is not an integral multiple of 2 dB. As a result, the cabinet-top output power cannot be adjusted at a step of 2 dB, and the TRX output power cannot be consistent with the cabinet-top output power. Therefore, this parameter provides a smaller step that can adjust the cabinet-top output power. GUI Value Range: DB0(0.0dB), DB2(-0.2dB), DB4(-0.4dB), DB6(-0.6dB), DB8(-0.8dB), DB10(-1.0dB), DB12(-1.2dB), DB14(-1.4dB), DB16(-1.6dB), DB18(-1.8dB), Default(Default) Actual Value Range: DB0, DB2, DB4, DB6, DB8, DB10, DB12, DB14, DB16, DB18, Default Default Value: Default
SNDMD
BSC6900 SET Meaning: RF send mode of the TRX. GTRXDEV(Optional) The BTS3006C and BTS3002E do not support Wide Band Combining, Power Booster Technology, DPBT, or Transmitter Independent or Combining. The DBS3900 GSM GRRU does not support Wide Band Combining, Transmitter Independent or Combining, Power Booster Technology, or DPBT. The BTS3900 GSM and BTS3900A GSM do not support Transmitter Independent or Wide Band Combining. GUI Value Range: NOCOMB(No Combination), PBT(PBT), WBANDCOMB(Wideband Combination), DIVERSITY(Transmit Diversity), DDIVERSITY(Dynamic Transmit Diversity), DPBT(DPBT), DTIC(Transmit Independency or Combination), NONE(none) Actual Value Range: NOCOMB, PBT, WBANDCOMB, DIVERSITY, DDIVERSITY, DPBT, DTIC, NONE Default Value: NOCOMB
SndRcvMode BSC6900 SET Meaning: The connection mode between the DRRU and the BTSRXUBP(Optiona antenna. l) GUI Value Range: SGL_ANTENNA(Single Feeder[1TX + 1RX]), SGLDOUBLE_ANTENNA(Single Feeder[1TX + 2RX]), DOUBLE_ANTENNA(Double Feeder[2TX + 2RX]), DOUBLEFOUR_ANTENNA(Double Feeder[2TX + 4RX]), DOUBLESINGLE_ANTENNA(Double Feeder[1TX + 1RX]),
Issue 01 (2011-03-31) Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd. 7-2
7 Parameters
Parameter ID NE
MML Command
Description DOUBLEDOUBLE_ANTENNA(Double Feeder[1TX + 2RX]) Actual Value Range: SGL_ANTENNA, SGLDOUBLE_ANTENNA, DOUBLE_ANTENNA, DOUBLEFOUR_ANTENNA, DOUBLESINGLE_ANTENNA, DOUBLEDOUBLE_ANTENNA Default Value: DOUBLE_ANTENNA
SndRcvMode1 BSC6900 SET Meaning: The connection mode between the DRFU and the BTSRXUBP(Optiona antenna. l) GUI Value Range: SGL_ANTENNA(Single Feeder[1TX + 1RX]), SGLDOUBLE_ANTENNA(Single Feeder[1TX + 2RX]), DOUBLE_ANTENNA(Double Feeder[2TX + 2RX]), DOUBLEFOUR_ANTENNA(Double Feeder[2TX + 4RX]), DOUBLESINGLE_ANTENNA(Double Feeder[1TX + 1RX]), DOUBLEDOUBLE_ANTENNA(Double Feeder[1TX + 2RX]) Actual Value Range: SGL_ANTENNA, SGLDOUBLE_ANTENNA, DOUBLE_ANTENNA, DOUBLEFOUR_ANTENNA, DOUBLESINGLE_ANTENNA, DOUBLEDOUBLE_ANTENNA Default Value: DOUBLE_ANTENNA UPGRADELE BSC6900 SET Meaning: Maximum output power that can be increased in V8PSK GCELLBASICPARA( 8PSK when the high-order modulation power increase function Optional) is enabled. GUI Value Range: 0~18 Actual Value Range: 0~1.8 Default Value: 18
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
7-3
8 Counters
8 Counters
Table 8-1 Counter description Counter ID 1282412285 Counter Name Counter Description Feature ID Feature Name
1282412286
HIGH.MOD.PWR.UPG.BU HM310:Number of Bursts with GBFD-118104 Enhanced RST.04.NUM High-Order Modulation Power EDGE Increase of 0.4 dB Coverage HIGH.MOD.PWR.UPG.BU HM311:Number of Bursts with GBFD-118104 Enhanced RST.08.NUM High-Order Modulation Power EDGE Increase of 0.8 dB Coverage HIGH.MOD.PWR.UPG.BU HM312:Number of Bursts with GBFD-118104 Enhanced RST.12.NUM High-Order Modulation Power EDGE Increase of 1.2 dB Coverage HIGH.MOD.PWR.UPG.BU HM313:Number of Bursts with GBFD-118104 Enhanced RST.16.NUM High-Order Modulation Power EDGE Increase of 1.6 dB Coverage HIGH.MOD.PWR.UPG.BU HM314:Number of Bursts with GBFD-118104 Enhanced RST.20.NUM High-Order Modulation Power EDGE Increase of 2.0 dB Coverage HIGH.MOD.PWR.UPG.BU HM315:Number of Bursts with GBFD-118104 Enhanced RST.24.NUM High-Order Modulation Power EDGE Increase of 2.4 dB Coverage HIGH.MOD.PWR.UPG.BU HM316:Number of Bursts with GBFD-118104 Enhanced RST.28.NUM High-Order Modulation Power EDGE Increase of 2.8 dB Coverage HIGH.MOD.PWR.UPG.BU HM317:Number of Bursts with GBFD-118104 Enhanced RST.32.NUM High-Order Modulation Power EDGE Increase of 3.2 dB Coverage HIGH.MOD.PWR.UPG.BU HM318:Number of Bursts with GBFD-118104 Enhanced RST.36.NUM High-Order Modulation Power EDGE Increase of 3.6 dB Coverage HIGH.MOD.PWR.UPG.BU HM319:Number of Bursts with GBFD-118104 Enhanced RST.40.NUM High-Order Modulation Power EDGE Increase of 4.0 dB or Above Coverage
1282412287
1282412288
1282412289
1282412290
1282412291
1282412292
1282412293
1282412294
1282412295
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
8-1
9 Glossary
9 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
9-1
10 Reference Documents
10 Reference Documents
There are no specific reference documents associated with this feature.
Issue 01 (2011-03-31)
Huawei Proprietary and Confidential Copy right Huawei Technologies Co., Ltd.
10-1