Escolar Documentos
Profissional Documentos
Cultura Documentos
DEVELOP GmbH
Applied Machine: /
PC-102
PC-202
PC-402
Machine
DF-605
OC-502
FS-508
PU-501
JS-502
MT-501
SD-502
SU-501
FK-503 ML-502
When installing the machine and associated options as a system, follow the order shown on the upper. Note: For the detailed installation procedures for each option, follow the instructions given in the corresponding Installation Manual and perform the procedures correctly.
4349U010AA
4349-7702-01
E-1
II.Accessory parts
No. Name Figure Qty After unpacking, be sure to get rid of the packaging materials and keep them out of the reach of children. Putting your head in the wrapper involves danger of suffocation. 1. Finisher Unit 1
4349U011AA
2. Tray Unit 1
4349U012AA
3. Front Cover 1
4349U013AA
4. Secondary Cover
4349U014AA
7. Retaining Plate
4349U016AA
1 1
9723
6 1
9735
10. Screw B (4 8 mm) 11. Screw C (3 8 mm) 12. Screw D (3 8 mm) 13. Label 14. Installation Manual
3
9735
6
9739
1 set
4980IXC019DA
E-2
4349IXC001DB
4349U017AA
4349U050AA
<Tray Unit>
4349IXC002DB
4. Remove the fixing bracket of the Finisher Unit (ten screws). Note: Screws 1 and 2 are used in step 6.
Screw 1
Screw 2
4349IXC004DA
E-3
4349IXC003DA
4349IXC005DA
6. Screw screws 1 and 2, which have been unscrewed from the fixing bracket in step 4, to the Staple Unit (two screws). * Screw them into the positions, from which they have been unscrewed.
4349U046AA
4349U024AA
12.Using a cutter or nippers, remove the Exit Rolls. * Gray Exit Rolls (three)
4349U023AA
4349U025AA
E-4
13.Holding the positions indicated by the arrows in the illustration, place the Finisher Unit onto the rail of the machine.
16.If the clearance measures more than 1 0.5 mm, slide out the Finisher Unit with the portion indicated in the illustration pushed with a screwdriver or similar tool.
Rail
4349U026AC
14.Slide the Finisher Unit all the way back into the machine.
4349U028AC
17.Loosen the adjusting screw and move the Finisher Unit to the right or left as necessary (one screw).
4349U027AA
15.Check to see if clearance A between the rail of the machine and the Finisher Unit measures 1 0.5 mm.
4349U029AC
18.After the adjustment have been made, tighten the adjusting screw.
Rail
Finisher Unit
4349U022AA
E-5
19.Make sure that the Paddle of the Finisher Unit is not advanced. 20.If the Paddle is advanced, push the solenoid shown and turn the Misfeed Clearing Dial to bring the Paddle into its retracted position. <NG> <OK>
22.Using Screws, secure the Tray Unit by tightening the screws in the order shown in the illustration (six screw As furnished with the Finisher).
5 1 3
2 4
Paddle
4349U031AA
4349IXC006DA
23.Using Screw, secure the ground wire (one screw B furnished with the Finisher). Note: Make sure that the ground wire runs in the direction shown in the illustration when secured.
4349U030AA
21.Mount the Tray Unit onto the Finisher Unit. Note: Use utmost care to prevent the Tray Unit from contacting the solenoid and motor of the Finisher Unit. Motor Solenoid 24.Connect the three connectors.
4349U034AB
25.Using Screw, secure the ground wire (one screw C furnished with the Finisher).
4349U057AA
4349U051AB
E-6
26.Using Screws, secure the Secondary Cover in position (two screw Cs furnished with the Finisher). Note: Make sure that there is a uniform clearance between the Misfeed Clearing Dial and Secondary Cover.
4349U052AA
31.Remove the cover from the Exit Cover that have been removed in step 9 (two screws).
4349U036AC
27.Using Screw, secure the Secondary Cover (one screw D furnished with the Finisher).
4349U039AB
32.Remove the label from the Front Cover. 33.Using the screws removed in step 31, secure the cover that have been removed in step 31 to the Front Cover (two screws). Label
4349U037AA
4349U040AD
4349U055AA
E-7
34.Using Screw, secure the band and the Retaining Plate to the Secondary Cover (one screw D furnished with the Finisher). 35.Fit the label back to the Front Cover.
4349U041AB
36.Close the Front Cover. 37.Install the upper and lower Exit Trays (four screw Ds furnished with the Finisher).
4349U043AB
38.Affix the Label furnished with the Finisher. <Reverse Automatic Document Feeder> <On Original Length Scale>
4349U044AB
4349U045AB
E-8