Escolar Documentos
Profissional Documentos
Cultura Documentos
SURGE ARRESTER SETS: QUICK SELECTION 420 PROTEC SURGE ARRESTERS, CLASS B/C 422 COMBTEC SURGE ARRESTERS, CLASS B/C 424 SPARK GAP BASED SURGE ARRESTERS, CLASS B 426 VARTEC SURGE ARRESTERS, CLASS C 429 SURGE ARRESTERS, CLASS C 432 SURGE ARRESTERS, CLASS D 434 ARRESTER DISCONNECTOR SWITCH, INDUCTIVE DECOUPLING 439
419
419
PGR 4950
uebspg_d.eps
420
PGR 4950
tn_c_set.eps
tnc.eps
COLOUR CODE
Switches with relay contact usually have a 1 at the end of the article number, e.g. IS 110331
tn_s_set.eps tns.eps
Colour code
imp
/ In
PGR 4950
tt_set.eps
421
tt.eps
W NOTE
This 3+1 switching operation can also be used in the TN-S and in IT networks. The N/PE surge arrester meets all standard requirements with 100kA(10/350) for BSK I,II, and 50kA(10/350) for BSK III, IV, as well as 20kA(8/20) for the C surge voltage protection.
Colour code Lightning protectn.Cl Description Type I imp / I n U c 1) Order no.
I, II III, (IV)
Switches with relay contact usually have a 1 at the end of the article number, e.g. IS 110311 ) Except for N/PE conductors in 3+1 switching operation (> 255V) ) Switching variants with the ISP have been ommitted here for reasons of clarity. 3 ) Sets are delivered as separate and are not pre-assembled. We would be happy to supply more detailed information about these sets and how they can interconnect where necessary.
1 2
bv25_s.eps
bvr25_s.eps
bg100_s.eps
BV 25-275/335 BVR 25-275/335 Varistor Continuous voltage Uc 275/335 VAC Nominal discharge current ln (8/20s) 40 kA Max. discharge current lmax (8/20s) 100 kA Lightning impulse current Iimp (10/350s) 25 kA Protection level Up at In 1600 V Protection level Up bei Iimp 1250 V Protection level Up (gas surge arrester)-(1,2/50s) Response time ta < 25 ns Max. permissible ambient temperature Degree of protection open/installed Max. permisible fuse: Short-circuit protection with max. fuse Enclosure material Max. terminal cross section DIN-rail mountable Model with auxiliary contact Auxillary contacts
BG100* N/PE Gas surge arrester 255 VAC 100 kA 150 kA 100 kA 1200 kV < 100 ns
422
-40 C up to +80 C IP 20/40 250 AgL 25 kA / 50 Hz Thermoplastic, self-extinguishing 25/35 mm2 both sides, top terminals for V wiring BVR 25-275/335 250 V AC/0,5 A, max. 1,5 mm2
*) In preparation: replacement type IS010094, can only be used as a N-/PE conductor in a 3+1 switching operation
tnc1.eps
uebsp_b3.eps
W RANGE OF APPLICATION
tns1.eps
Varistor-lightning arresters/surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges. Can be used for construction systems with I and II classes of protection in accordance with EN/IEC E 8049. The surge arrester operates in any position. The application of varistor technology extinguishes mains follow currents. It also ensures that connected devices are stress free and also offers a lower protection set off. No additional gas-filled blow-out spark gaps are required.
tt1.eps
PU 6 6 6 6 50 50
TYPE BV 25/335 BVR 25/335 BV 25/275 BVR 25/275 PES 3x2 PES 4x2
423
) EN/IEC design according to VE/NORM 8001-1, section18. Must be implemented by law in Austria. ) Export model- must not be implemented in Austria.
PGR 4955
bv_m.eps
is010081.eps
is010083.eps
vv_s.eps
vs_s.eps
vv25_s.eps
vs335_s.eps
Continuous voltage Uc Nominal discharge current ln (8/20s) Max. discharge current lmax (820s) Lightning impulse current Iimp (10/350s) Protection level Up at In Protection level Up at Iimp Response time ta
VV 275/335* Varistor 275/335 VAC 40/40 kA 80/80 kA 12.5/12.5 kA 1,8/1,8 kV 1,2/1,2 kV < 25/< 25 ns
424
Max. permissible ambient temperature -40 C up to +80 C Degree of protection open/installed IP 20/40 Max. permisible fuse: 250 AgL Short-circuit protection with max. fuse 25 kA/50Hz 25 kA/50Hz Enclosure material Thermoplastic, self-extinguishing V0 Max. terminal cross section 25/35 mm2 DIN-rail mountable on both sides Model with auxiliary contact VVR 335 VSR 335 2 Auxillary contacts 250 V AC/0,5 A, max. 1,5 mm
*) Use N/PE surge arrester IS010084 when using the 3+1 switching operation.
vvr25_s.eps vsr335_s.eps
vv_tn_s.eps
vv_tnc_s.eps
W RANGE OF APPLICATION
Combined lightning arresters/surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient surge voltages. Are ideally used for construction systems having protection class III and (IV) according to VE/NORM E 8049. Surge arrester operates in all locations. Coupling VV-SG50-VS surge arresters provide a low protection level in a variety of network systems (TT/IT/TN-C/TN-C-S) with the width of an RCCB of only 4 MW (3+1 switching operation 6 MW) without any mains follow currents.
vv_31_s.eps
PU 6 6 6 6 6 6 6 6 50 6 50 50
TYPE VV 335 VS 275 VVR 275 VSR 335 VV 275 VS 335 VVR 335 VSR 275 PES 2x2 SG50 PES 3x2 PES 4x2
WEIGHT 0,296 0,226 0,306 0,236 0,296 0,226 0,306 0,236 0,226 -
ORDER NO. IS010081 IS010183 IS010185 IS010087 IS010181 IS010083 IS010085 IS010187 IS010172 IS010084 IS010173 IS010174
35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 35x90x64 -
Combtec VVR 12,5 kA + H IEC 2) Combtec VSR 12,5 kA+H VE 1) Combtec VV 12,5 kA IEC 2) Combtec VS 12,5 kA VE )
1
425
CU-Busbar, 2x f. TN-C network Lighting arrester N/PE-50 kA, SG50 CU-Busbar, 3x f. TN-C network CU-Busbar, 4x f. TN-S TT network
1 2
) VE/NORM design according to VE/NORM 8001-1, section18. Must be implemented by law in Austria. ) Export model must not be implemented in Austria.
PGR 4952
is0101_gf.eps
45
90
Level of protection < 2,5 kV No blow-out opening, hence no need for spark gaps Optional relay contact Test current 25 kA, 60 kA (10/350s) High Insulation resistance Risol > 1010 Rated voltage Uc: 335 V~ Nominal operating voltage Un: 230 / 400 V AC 50/60 Hz Response time < 50 ns Max. permissible conductor/back-up fuse F2 with single drop 160 A gL Max. permissible conductor/back-up fuse F3 with V-wiring: 100 A gL Operating temperature range: -40 C up to +85 C Max. cable cross-section: multi-wired 50 mm2 / fine-wired 35 mm2 Enclosure material / colour: Polycarbonate (halogen-free)/ grey RAL 7035 Degree of protection: IP 20 Mounted on DIN-rail 35 mm accord. to EN 50 022
W CERTIFICATIONS
tested in accordance with E DIN VDE 0675-6-11/98-A1 and EN 61643-11 /IEC 61643-1and VE 8001-1. Classification accord. to class B/C, I + II, T1, T2
W PRODUCT DESCRIPTION:
POWERTEC 25, 60 (R) with a low protection level is a selective, two-level T1 + T2 (B+C) surge arrester, which combines protection classes I+II in a single device. This means no decoupling elements are required for cable lengths under 10 m. Using hermetically sealed spark gaps filled with inert gas means that the requirement of a high discharge capacity is fulfilled while maintaining functional stability. The first level (non-linear resistor type arrester) discharges impact currents (up to 4kA) without causing any mains follow-currents. When a pre-defined impact current (up to 4 kA) has been exceeded, the second level (the hermetically sealed spark gap filled with inert gas) engages for the less common discharge of highenergy transients up to 25 kA / 60 kA (10/350 s) which may arise during close-up or direct lightning strikes. As an option, a potentialfree relay contact (R) with terminal is included in the enclosure- to aid signalising. V-wiring can be easily installed using the unlabelled terminal (the one not connected with the L/N terminal in the device) using the optional 2-pole comb-type rail.
uebsp_m1.eps
426
uebsp_a.eps
DESCRIPTION
PU 1 1 1 1 50 50
Lightning arrester, 25 kA KI/II B/C Lightning arrester, 25 kA+H CI/II B/C Lightning arr. 60 kA KL.I/II B/C Lightning arr. 60 kA+H KI/II B/C CU-Busbar, 3x f. TN-C network CU-Busbar, 4x f. TN-S TT network
PGR 4952
is0100_gf.eps
45
90
35
uebsp_m2.eps
50 64
W CERTIFICATIONS
Test in accordance with EN 61643-11 & IEC 61643-1, VE 8001-1
W RANGE OF APPLICATION
uebsp_b2.eps
SG50 used in combination with COMBTEC VV, VS, G100 in combination with PROTEC, POWERTEC in 3 + 1 switching operation is used to protect against direct lightning strikes in external overhead lines or external lightning arrester in the TT system. See graphic for application.
W PRODUCT DESCRIPTION:
SG 50, G 100 are 1-pole N/PE lightning arresters with protection class I+II+III (B+C+D) for protection against partial lightning currents from entering electrical installations. The device is used for equipotential bonding of lightning protection in the 400/230 VAC TT system, as a N/PE conductor with 3 + 1 switching operation. It is able to deflect lightning currents up to 50 kA / 100 kA (10/350 s) with a charge of 50 As, and has a low protection level, Up < 1,5 kV. The use of a hermetically-sealed high-performance spark-gap filled with inert gas makes use of a dangerous blow-out opening superfluous.
uebsp_b1.eps
427
uebsp_b4.eps
W FAULT DETECTION
When required, this arrester can also be tested using an insulation meter. When Risol 0.5 to 1 M, the arrester must be replaced at the next opportunity, when Risol < 0.5 M it must be replaced immediately.
DESCRIPTION
PU 6 1 50
N/PE lightning arrester, 50 kA, SG50, N/PE lightning arrester, 100kA G100 CU-Busbar, 4x f. TN-S TT network
428
80 45
17,5
7n5b4976.eps 7n5b4990.eps vvp_m.eps
W TECHNICAL DATA
Class C, design type II, type 2, meets VE-SN 60, part 4 & EN/IEC 61643
7n5b4992.eps
7n5b4994.eps
VPP 255/355
DVP 255
vpp_s.eps
dvp255_1.eps
Continuous voltage Uc Nominal discharge current ln (8/20s) Max. discharge current lmax (8/20s) Protection level Up at In Response time ta Max. permissible ambient temperature Degree of protection open/installed Max. permisible fuse: Max. terminal cross section Auxiliary contact (optional) DIN-rail mountable Max. terminal torque
VVP 255 Varistor 255 VAC 15 kA/20 kA 30 kA/40 (30) kA 1,3/1.4 kV < 25 ns
100 A
VVP 335 DVP 255 2) Varistor Gas-filled surge arrester 335 VAC 255 VAC 15 kA/20 kA 20 kA 30 kA/40 (30) kA 40 kA 1,4 kV/1,65 kV 1 ,2 kV < 25 ns < 100 ns -40 C up to +80 C IP 20/40 100 A 16/25 mm2 250 V AC/0,5 A, max. 1,5 mm2 on both sides 2,5 - 3,0 Nm (main terminal)
429
vpp_h_s.eps
dvp255_2.eps
tn_c_s.eps
tn_s_s.eps
tn_cs_s.eps
W RANGE OF APPLICATION
Plug-in surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges The surge arrester operates in any position. Terminal assignment for the mains and PE/PEN- conductor is freely definable. Also see SET - article, page 420, 421.
DESCRIPTION
PU 12 12 12 12
3
TYPE VVP335-15 VVP335-20 VVP255-15 VVP225-20 DVP255 VPS/1 VPSH/1 DPS/1 DPSH/1 VPS/3+1 VPSH/3+1 VII-3 VII-4 VII-5
ORDER NO. IS010078 IS010079 IS010076 IS010077 IS010075 IS010071-A IS010069-A IS010070-A IS010068-A IS010064-A IS010065-A IS050103 IS050104 IS050105
C-arrester module 15 kA VE VVP335 1) C-arrester module 20 kA VE VVP335 1) C-arrester module 15 kA IEC VVP255 )
2
430
C-arrester module 20 kA IEC VVP255 2) N-PE surge arrester Module 20kA DVP255 ) Base,1-pol. for VVP Base,1-pol. for VVP +H Base,1-pol. for DVP Base,1-pol. for DVP +H Base 3+1 operation Base 3+1 operation +H
Busbar , 3x, insulated, for TN-C system Busbar , 4x, insulated, for TN-S, TT system Busbar , 5x, insulated, for N arrangement
12 12 12 12 12 3 3 10 10 10
1 2 3
)VE design according to VE 8001-1, section18. Must be implemented by law in Austria. )Export model must not be implemented in Austria. ) As specified in NORM/VE E8001-1, the 20kA requirement still applies to the surge arrester between Neutral and the main earthing rail (N/PE conductor). (PAS) or PE-rail, even in cases where surge protection devices were installed with greater nominal discharge currents, e.g. 15 kA or 20 kA between the external conductors and the Neutral conductor.
W
is010073.eps var_s1.eps
65
90 45
W RANGE OF APPLICATION
17,5
var_s2.eps vepg_m.eps
Surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges The surge arrester operates in any position. The connection line to the equipotential bonding rail or PE rail should be as short as possible and without looping. When measuring insulation, the surge arrester is disconnected from PE by the gas-filled spark gap. VEPG Varistor + gas surge arrester 335 VAC 10 kA / Pol 20 kA / Pol 1,6 kV at 5 kA 950 V < 100 ns -40 C up to +80 C IP 20/40 100 A L, N = 6 mm2; PE = 25/35 mm2 250 VAC / 0,5 A; max. 1,5 mm2
Continuous voltage Uc Nominal discharge current ln (8/20s) Imax (8/20s) Level of protection Up at In Response time ta Max. permissible ambient temperature Degree of protection open/installed Max. permisible fuse: Max. terminal cross section Auxiliary contact (optional)
431
PU 1 12 12 ORDER NO. IS010073 IS010201 IS010202
DESCRIPTION
C surge arrester, 10 kA, 335 V, 1-phase, 1 modul wide Base for VMG / VEPG Base + H for VMG / VEPG
PGR 4953
is010045.eps
is01_23s.eps
Observe the rated voltage when choosing a surge arrester. When using surge arresters in Austria, select according to the binding regulation VE 8001-1, Pt. 18 Uc 335 V.
W CERTIFICATIONS
VE
432
is01_46s.eps is01_41s.eps
W RANGE OF APPLICATION
To protect consumer units against transient surge voltages caused by indirect lightning strikes and switch operations.
80
45
17,5 5,5
is01_46m.eps
44 61,5
is01_xx.eps
PU 4 4 4 4 12 6 4 3 3 8 10 10 10 10
TYPE UAS 20/280 UAS 20/335 UAS 20/460 UAS-N/PE UAS/U1 UAS/U2 UAS/U3 UAS/U4 UAS /3+1 UAS-FM VII-2 VII-3 VII-4 VII-5
ORDER NO. IS010045-A IS010052-A IS010051-A IS010053 IS010046 IS010047 IS010048 IS010049 IS010054 IS010044 IS050102 IS050103 IS050104 IS050105
Varistor insert, 20 kA, for export, 280 V ) Varistor insert, 20 kA, 335 V EN/IEC 1) Varistor insert, 20 kA, 460 V EN/IEC )
1
N/PE conductor, 20 kA, 260 V EN/IEC, only available for 3+1 switching operation Base, 1-pole (coded for N/PE conductor) Base, 2-pole (coded for N/PE conductor) Base, 3-pole (coded for N/PE conductor) Base, 4-pole (coded for N/PE conductor) Base 3+1 operation Plus relay contact, 1 C/O Rail, 2x, insulated
Busbar , 3x, insulated, for TN-C system
Busbar, 4x, insulated, for TN-S, TT system Busbar, 5x, insulated, for N arrangement
1) VE design according to VE 8001-1, section18. Must be implemented by law in Austria. 2) Export model- must not be implemented in Austria.
433
W PLUG-IN SURGE ARRESTER, D CLASS, VMG SERIES FOR SINGLE PHASE OPERATION, 230 V, 1 MODUL WIDE
W TECHNICAL DATA
Class D, design type II, type 2, meets VE-SN 60, part 4 & EN/IEC 61643
is010201gf.eps
is010201.eps
W RANGE OF APPLICATION
is010200.eps var_s1.eps
is0102_s.eps
D class surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges. The surge arrester operates in any position. The connection line to the equipotential bonding rail or PE rail should be as short and possible and without looping. When measuring insulation, the surge arrester is disconnected from PE by the gas-filled spark gap. Only for use in TN systems. VMG 275 Varistor + gas surge arrester 275 VAC 3 kA / Pol 6 kV / Pol 0.9 V < 100ns -40 C up to +80 C IP 20/40 63 A L, N = 6 mm2; PE = 25/35 mm2 250 VAC / 0,5 A; max. 1,5 mm2 on both sides
434
Continuous voltage Uc Nominal discharge current ln (8/20s) Uoc (1,2/50) Protection level Up at In Response time ta Max. permissible ambient temperature Degree of protection open/installed Max. permisible fuse: Max. terminal cross section Auxiliary contact (optional) DIN-rail mountable
DESCRIPTION
PU 6 12 12
D surge arrester Module 3kA, 1 MW Base for VMG / VEPG Base + H for VMG / VEPG
PGR 4954
is0500m2.eps
Test class II following IEC 61643-1 Class D following VE-SN 60, part 1 Response time (RRV 5kV/s) ta < 25 ns Continuous voltage UE: 280 V, 335 V, AC Combined impact Uoc L-N / N-PE: 5 kV / 10 kV Level of protection UP at Uoc L-N /N-PE: 900 V / 1000 V / 1200 V Rated discharge current In L-N/L-PE/N-PE: 2,5 kA/ 2,5 kA/5 kA (8/20 s) Level of protection UP at In L-N/L-PE/N-PE: 900 V/ 1900 V/ 1000 V Max. discharge current L-N/L-PE/N-PE: 5 kA/5 kA/ 10 kA (8/20 s) Max. permitted back-up fuse: 63 A gL/C63 Max. permitted short-circuit protection: 10 kA Max. permissible ambient temperature: -40 C to +70 C Built-in contactor: IP 40 Gap terminals on both sides for conductor cross-section 1 -25 mm2 Claw-type terminal on both sides for rails up to 1,5 mm in strength Torque for screw terminals 2,4 up to 3 Nm Quick-fastening onto rail in accordance with EN 50,022 Installation class 3 according to IEC 1000-4-5 UAS-FM auxiliary contact can be fitted for remote signalling No need to decouple upstream surge protection
W RANGE OF APPLICATION
Used to protect terminal units against transient surges as low-voltage device arresters.
435
DESCRIPTION
PU 12 12 6 12 12 6
Modular D surge arrester N/PE (spark gap), 2.5 kA, 260 VAC
Requirement class D Rated discharge current (8/20 s) Isn: 2.5 kA Rated voltage Uc: 250 V~ (50Hz) Connection type: Response time: Short-circuit protection: Temperature range: Max. load circuit current I max:16 A 3 wire L - N < 25 ns 6 kA (back-up fuse 16 AgL) -20 C to 60 C
W RANGE OF APPLICATION
The protective device is primarily designed for fusing sensitive electronic devices mains-side, and is suitable for universal application in flush-mounted modular device- and enclosure sockets. This device allows you to equip already existing flush-mounted plug sockets with surge protection. The protective device is clamped into a FM- device insert using a spring clip after the L, N and PE conductors are connected to the plug socket- on the device side. Afterwards, the plug socket is mounted as usual. This enables the user not only to equip plug sockets to be installed for the first time but also to retrofit existing plug sockets, regardless of individual models of different manufacturers. The switching operation of the device provides parallel protection. This ensures that supply to the protected device- mains-side is maintained even if the protective device is damaged. Fault indication is provided by a sensor integrated in the device. This indicates when protection is no longer provided, in which case the protective device should be replaced by an electrician as soon as possible.
is0102_mon.eps
DESCRIPTION
PU 1 1
D Surge arrester for plug socket, 2,5 kA D Surge arrester for plug socket, 2,5 kA, through-wiring
436
PGR 4954
W TECHNICAL DATA
Surge arrester class D - meets VDE 0675, part 6/A3 11.97 Test class II meets IEC 61643-1 Continuous voltage Uc 250V/50 Hz Max. permissible back-up fuse 16 A gL Nominal discharge current isn (8/20)s symm./asymm. (PE) 1,5 kA Max. discharge current Imax (8/20)s symm./asymm.(PE) 4,5 kA Response time symm. < 25 ns / asymm.(PE) < 100 ns Residual voltage at Isn symm. < 1,2 kV / asymm.(PE) < 650 V Protection level at UOC symm./asymm. 1.5 kV
N N PE PE L L
43 34
47,5 28
47,5 71
is050001.eps
is05_1m.eps
is05_2m.eps
is05_3m.eps
Temperature range -40C to +75 C Degree of protection according to IEC 529: 1989 IP 20 Integrated FM contact integriert: max. permissible operating voltage 250 V AC, max. permissible operating current 3 A / 45 C Mounting in cable channels and flush-mounted sockets accord. to DIN 49073 flexibel/mm2 Connections fixed/mm2 Mains 0,2 - 4 0,2 - 2,5 FM contact 0,14 - 1,5 0,14 - 1,0
W RANGE OF APPLICATION
Protects terminal devices against transient voltage surges.
K-SE-ELSO4
W CAUTION!
A class C/II surge arrester must be installed upstream in the enclosures to prevent the device from being overloaded.
DESCRIPTION
PU 1 1 1 1 1 10 1 1
ORDER NO. IS050000 IS050001 EL204100 EL204104 EL206010 EL206014 IS050002 IS050003
Plug-in base Varistor insert ELSO frame, 1x (For additional details, colours, types etc. refer to the Special Catalogue K-SE-ELSO4) ELSO frame, 2x (For additional details, colours, types etc. refer to Special Catalogue K-SE-ELSO4) ELSO cover plate Fashion, pearl white (For additional details, colours, types etc., refer to Special Catalogue K-SE-ELSO4) ELSO cover plate, pure white (further details, colours, types etc., see Special Catalogue K-SE-ELSO4) Cover plate, alternative to ELSO Cover frame, alternative to ELSO
437
DA RA
PGR 4954
el215130.eps
is01_11f.eps
W RANGE OF APPLICATION
Earthed plug socket with integrated surge protection for mounting in flush-mounted sockets, used to protect terminal devices from transient voltage surges.
W CAUTION!
A class C/II surge arrester must be installed upstream in the enclosures to prevent these devices from being overloaded.
DESCRIPTION
PU 1 1 1
TYPE
Fashion pearl white Fashion pure white
WEIGHT -
ELSO, 2,5 kA, w/o frame (further details, colours, types etc. see Special Catalogue K-SE-ELSO4) ELSO, 2,5 kA, w/o frame (further details, colours, types etc. see Special Catalogue K-SE-ELSO4) Surge arrester socket w/ optical and acoustic sensor
SKTG
0,132
438
bd900600.eps
W UPON REQUEST
PGR 4320
35
43,5 58
is010043.eps
is01_43m.eps
is01_43s.eps
DESCRIPTION
PU 1
TYPE LBA 35
WEIGHT 0,408
Inductive decoupling, 35 A
439
NOTES
440