Escolar Documentos
Profissional Documentos
Cultura Documentos
00
06/27/12
TOYOTA PRIUS V 2012 Part Number: 00016-47250; 01;02;03;04;06;08;12 Accessory Code: MW30
Conflicts
Note:
Kit Contents
Item # 1
Quantity Reqd. 1
00016-47250-02
00016-47250-08
00016-47250-01
00016-47250-03
00016-47250-04
00016-47250-06
00016-47250-12
Description
X X X X X X
Barcelona Red Metallic (3R3) Magnetic Gray Metallic (1G3) Blue Ribbon Metallic (8T5) Clear Sky Metallic (787) Blizzard Pearl (070)
Recommended Tools
Safety Glasses
Safety Tools
Special Tools
General Applicability
Note: Prius V Models 2012 Item # 1 2 Accessory Paint Protection Film Body Side Molding
Installation Tools
*Mandatory
Special Chemicals
Cleaner
SPECIAL NOTE: After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality.
Page 1 of 5
TOYOTA
PRIUS V
1. Verify that the part is for the correct vehicle model and that it fits the vehicle properly. 2. During installation, the vehicle, the part, and the tape MUST be between 60 and 110 F for proper adhesion. Failure to maintain proper installation procedure may result in the part not functioning correctly. 3. Inspect the vehicle and parts for damage prior to installing the Body Side Molding.
Mark
13.17
Fig. B1
i. Paint: Prepare part surfaces per Toyota paint standards. Do not use lacquer thinner or enamel reducer as a degreaser. 4. Make sure that all Body Side Molding installation surfaces are free of dirt and/or grease. (Fig. A1)
i.
Mark 24
B. Installation
Fig. B2
1. From the bottom of the rear door, at the center door seam on the vehicle rocker, measure up 13.17" and mark vehicle with a grease pencil. (Fig. B1) 2. Along the bottom of the front door, measure 24 forward from the back edge of the door and mark vehicle with a grease pencil (Fig. B2) 3. From the bottom of the front door, perpendicular with the mark made in Step 2, measure up 12.69" and mark vehicle with a grease pencil. (Fig. B3)
Mark
12.69
Fig. B3
Page 2 of 5
TOYOTA
PRIUS V
24
Mark
Fig. B4
5. From the bottom of the rear door, perpendicular with the mark made in Step 4, measure up 13.60" and mark vehicle with a grease pencil. (Fig. B5) 6. Using marks made in Steps 1, 3 and 5, place magnetic straight edge under marks on vehicle. (Fig. B6) 7. Pull back ends of tape liner and bend to outside of part prior to installation. (Fig. B7) 8. Position Body Side Molding using magnetic straight edge applied in Step 6 as a guide (Fig. B8). Remove remaining tape liner and press into place.
Mark
13.60
Fig. B5
Fig. B6
Fig. B7
Fig. B8
Page 3 of 5
TOYOTA
PRIUS V
ii. The end of the rear Body Side Molding piece is angled parallel with the door seam. (Fig. B11) 10. Apply firm pressure with roller or presser to the taped areas for proper bond. Tape reaches maximum adhesive bond after 24 hours of contact. 11. Installation Complete. (Fig. B12)
Fig. B10
Fig. B11
Fig. B12
Page 4 of 5
TOYOTA
PRIUS V
NOTE: Due to the inconsistency of factory sealant, it may be necessary to apply the bodyside molding over the clear door edge film protection.
Check:
Accessory Function Check Check visual alignment No gap is allowed between the tape and the vehicle door surface Vehicle function checks
Look For:
Molding should be straight No gap is allowed between the tape and the vehicle door surface Open and close both rear doors to ensure the molding does not rub or hit door frame.
Page 5 of 5