Escolar Documentos
Profissional Documentos
Cultura Documentos
+
28. Define slip of the belt
1 1
2 2
N d
N d
1
100
S 1
1
]
29. What is the length of open belt drives?
L= [ ]
( )
2
1 2
1 2 2
2 4
d d
d d x
x
+ + +
,
30. What is the length of a crossed belt drives?
L= [ ]
( )
2
1 2
1 2 2
2 4
d d
d d x
x
_
+
+ + +
,
31. Define creep of the belt.
Tension on the two pulleys is not equal. One side, the tension is greater than the
other side due to the difference of two tensions, the belt continuously creeps over the
pulleys. This movement of the belt is very small and is called creep of belt.
5
32. Define angle of contact or lap.
It is the angle subtended by the arc AB along which the belt touches the pulley at
the centre. It is denoted by
32. What is the angle of contact for?
(a) Open belt drive
(b) Cross belt drive?
Open belt drive (180 - 2 )
180
rad
Cross belt drive (180 + 2 )
180
rad
33. What is the ratio of driving tension for flat belts?
2.3 log
1
2
T
T
1
1
]
34. Define centrifugal tension in a belt.
Tc = mV
2
=
W
g
V
2
35. What is the condition for the maximum power transmission?
P = (T
1
T
2
) V
For maximum power transmission
T = 3T
c
36. What is the ratio of driving tension for V belt?
2.3 log
1
2
T
T
1
1
]
cosec
37. What is clutch?
A clutch is a machine member used to connect a driving shaft to a driven shaft so
that the driven shaft may be stared or stopped at with or with out stopping the driving
shaft. It is used in automobile.
38. What are the types of clutches?
Positive clutch
Friction clutch
6
39. What are the types of friction clutch?
Disc or plate clutch
Cone clutch
Centrifugal clutch
40. What is a single plate clutch?
It is consist of the following parts
Driving plate
Driven plate
Pressure plate
41. What are the functions of clutch?
To engage or disengage the rest of transmission as required.
To transmit the engine power to rear wheels when the rear wheels without shock.
To enable the gear to get engaged when the vehicle is in motion.
42. What are the factors to be considered when designing a disc or plate clutch?
When there is a uniform pressure
When there is a uniform axial wear.
43. What is the formula for finding intensity of pressure?
P =
( ) ( )
2 2
1 2
W
r r
1
]
44. Define average pressure P
av
?
P
av
= Total force on friction surface /Cross-sectional area of friction surface
45. What is the total frictional torque acting on the ring of the cone clutch?
( ) ( )
( ) ( )
3 3
1 2
2 2
1 2
2
3
n
r r
T W
r r
1 1
]
1
1
1
1
] ]
46. What is bearing?
A bearing is a machine element which supports another moving machine element
known as journal. It permits a relative motion between the contact surfaces of the
member while carrying the load.
47. What are the types of bearing?
Radial bearing
7
Thrust bearing
Sliding bearing
Rolling contact bearing
48. Define journal bearing or sleeve bearing?
The sliding bearing in which the sliding action is along the circumference of a
circle or an arc of a circle and carrying radial loads are known as journal or sleeve
bearings.
49. What is the thick film or hydrodynamic lubricated bearing?
The thick film bearing are those in which the working surfaces are completely
separated from each other by the lubricant. Such type of bearing are called hydrodynamic
lubricated bearing
50. What is zero film bearing?
The zero film bearing are those which operate with out any lubricant present
51. What is wedge film lubrication?
The flow of a viscous fluid in a converging channel is known as wedge film
lubrication.
52. What is squeeze film lubrication?
The resistance of a viscous fluid to being squeezed out from between approaching
surfaces known as squeeze film lubrication.
53. What are the types of rolling contact bearing?
Ball bearing
Roller bearing
54. What are types of friction clutch?
Disc clutch
Cone clutch
Centrifugal clutch
55. Mention any two advantages of V belt drive over flat belt drive.
It provides longer life 3 to 5 years
It can be easily installed and removed
High velocity ratio
Drive is positive.
8
56. What is creep in belt?
When the belt passes from the slack side to the tight side a certain portion of the
belt extend and it contracts again when the belt passes from tight side to slack side. Due
to these changes of length there is a relative motion between the belt and the pulley
surfaces. This relative motion is termed as creep of belt.
57. Define Cam.
A cam is a rotating machine element which gives reciprocating or oscillation
motion to another element known as follower.
58. Where are cams used?
The cams are widely used for operating the inlet and exhaust valves of IC engines
automatic attachment of machineries paper cutting machines etc.
59. What are the types of follower?
Knife edge follower
Roller follower
Mushroom follower
Spherical face follower
Reciprocating Oscillation follower
Radial follower
Offset follower
60. Define Radial follower
When the motion of the follower is along an axis passing through the centre of the
cam it is known as radial follower.
61. Define offset follower.
When the motion of the follower is along as axis away from the cam centre it is
called offset follower.
62. What are the types of cams?
Radial or Disc cam
Cylindrical cam
9
63. Define pressure angle
It is the angle between the direction of the follower motion and a normal to the
pitch curve. If the pressure angle is too large a reciprocating follower will jam in its
bearing.
64. What are the motions of the follower?
Uniform velocity
Simple harmonic motion
Uniform acceleration and retardation
Cycloidal motion
65. What are dwell periods?
The period during which the follower remains at rest are known as dwell periods.
66. Define angular velocity.
It may be defined a ratio of change of angular displacement with respect to time.
It is a vector quantity.
67. Define a gear.
A gear is a wheel provided with teeth which mesh with the teeth on another wheel
or on to rack so as to give positive transmission of motion from one component to
another.
68. What are the types of gears?
Spur gear
Helical gear
Bevel gear
Worm gear
Rack and pinion
69. Define pitch circle
It is an imaginary circle which by pure rolling action would give the same motion
as the actual gear.
70. Define pressure angle
It is the angle between the common normal to two gear teeth at the point of
contact and the common tangent at the pitch point. It is denoted by The standard
pressure angles are 141/2
and 20
10
71. Define Dimeteral pitch.
It is the ratio of number of teeth to the pitch circle diameter in mm
72. Define module.
It is the ratio of the pitch circle diameter in mm to the number of teeth.
73. Define arc of contact
It is the path traced by a point on the pitch circle from the beginning to the end of
engagement of a given pair of teeth.
74. State law of gearing.
The common normal at the point of contact between a pair of teeth must always
pass through the pitch point.
75. Define interference
The phenomenon when the tip of a tooth under cuts the root of its mating gear is
known as interference.
76. Define gear train
The combination of gear wheels by mean of which motion is transmitted from one
shaft to another shaft is called a gear train.
77. What are the types of gear train?
Simple gear train
Component gear train
Epicyclic gear train
78. What is simple gear train?
A simple gear train is one in which each shaft carries one wheel only. Simple gear
trains are employed where a small velocity ratio is required.
79. Define train value
It is the reciprocal of velocity ratio
=
Speed of the driven No. of teeth on driver
Speed of the driver No. of teeth on driven
80. What is a compound train?
A compound gear train is one in which each shaft carries two wheels one of
which acts as a follower and other acts as a driver to the shaft. It is used for high velocity
ratio.
11
81. What are the uses of epicyclic gear train?
Transmitting high velocity ratio, with gears of moderate size in a comparatively
lesser space.
82. What are the types of vibration?
Free vibration
Force vibration
Damped vibration
83. What are the free vibrations?
Longitudinal vibration
Transverse vibration
Tensional vibration
84. What is degree of freedom?
The minimum number of independent coordinates required to specify the motion
of a system at any instant is known as degree of freedom of the system.
85. What is simple harmonic motion?
The motion of a body, to and fro a about a fixed point is called simple harmonic
motion.
86. What is critical or whirling or whipping speed?
It is the speed at which the shaft tends to vibrate violently in the transverse
direction. The critical speed of the shaft in rps is equal to the natural frequency of
transverse vibration in HZ.
87. What is force vibration?
When the body vibrates under the influence of external force then the body is said
to be under force vibration.
88. What is magnification factor?
The ratio of maximum displacement of the forced vibration to the static deflection
under static force is known as magnification factor.
89. What is frequency response curve?
A curve between magnification factor and frequency ratio ids known as is
frequency response curve.
12
90. What is transmissibility?
It is defined as the ratio of the force transmitted to the force applied on the
system.
91. What is torsionally equivalent shaft?
It is the shaft which has the same torsional stiffness as that of the stepped shaft so
that it twists to the same extent under a given torque as the stepped shaft would.
92. What is single rotor system?
A shaft fixed at one end carrying a rotor at the free end, is known as single rotor
system.
93. What is node?
The point is section at which the amplitude of vibration is zero, is known as node.
94. What is two node frequencies?
One set of values given by the quadratic equation gives the position of two node
and the frequency thus obtained is known as two node frequency.
95. What is balancing?
Balancing is the process of designing or modifying machinery so that the
unbalance is reduced to an acceptable level and if possible is eliminated entirely.
96. What is mass moment?
The product of B.b or m.r is called as the mass moment.
97. What is reference plane?
Transfer the centrifugal force acting in each plane to a single parallel plane which
is termed as reference plane.
98. What is static balance?
A system is rotating masses is said to be in static balance if the combined mass
centre of the system lied on the axis of rotation.
99. What are conditions for complete balancing?
The resultant centrifugal forces must be zero
The resultant couple must be zero.
100. What is dynamic balance?
A system of rotating masses is in dynamic balance when there does not exist any
resultant centrifugal force as well as resultant couple.
13
101. What are the types of locomotive?
Coupled locomotive
Uncoupled locomotive.
102. Define tractive force
The resultant unbalance force due to the two cylinders along the line of stroke is
known as tractive force.
103. What is swaying couple?
The unbalance forces acting at a distance between the line of stroke of the two
cylinders constitute a couple in the horizontal direction. This couple is known as swaying
couple.
104. Define hammer blow
The maximum magnitude of the unbalance forces along the perpendicular to the
line of stroke is known as hammer blow.