Escolar Documentos
Profissional Documentos
Cultura Documentos
FEATURES
Divide-by-4 prescaler High frequency operation: 4 GHz to 18 GHz Integrated RF decoupling capacitors Low power consumption Active mode: 30 mA Power-down mode: 7 mA Low phase noise: 150 dBc/Hz Single dc supply: 3.3 V compatible with ADF4xxx PLLs Temperature range: 40oC to +105oC Small package: 3 mm 3 mm LFCSP
BIAS
ADF5001
VDDx 100 100 1pF RFOUT RFOUT 1pF
3pF RFIN
DIVIDE BY 4
50
08402-001
APPLICATIONS
PLL frequency range extender Point-to-point radios VSAT radios Communications test equipment
GND
Figure 1.
GENERAL DESCRIPTION
The ADF5001 prescaler is a low noise, low power, fixed RF divider block that can be used to divide down frequencies as high as 18 GHz to a lower frequency suitable for input into a PLL IC, such as the ADF4156 or ADF4106. The ADF5001 provides a divide-by-4 function. The ADF5001 operates off a 3.3 V supply and has differential 100 RF outputs to allow direct interface to the differential RF inputs of PLLs such as the ADF4156 and ADF4106.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 20092010 Analog Devices, Inc. All rights reserved.
REVISION HISTORY
6/10Rev. 0 to Rev. A Change to Features Section ............................................................. 1 Change to Applications Section ...................................................... 1 Changes to Figure 1 .......................................................................... 1 Changes to Specifications Section .................................................. 3 Changes to Thermal Impedance Ratings, Table 2 ........................ 4 Changes to Figure 4 Through Figure 7 .......................................... 6 Changes to Evaluation Board PCB Section ................................... 7 Changes to Figure 8 .......................................................................... 7 Change to Table 4 ............................................................................. 7 Changes to Figure 10 ........................................................................ 8 Changes to Ordering Guide ............................................................ 9 10/09Revision 0: Initial Version
Rev. A | Page 2 of 12
ADF5001 SPECIFICATIONS
VDD1 = VDD2 = 3.3 V 10%, GND = 0 V; dBm referred to 50 ; TA = TMIN to TMAX, unless otherwise noted. The operating temperature range is 40C to +105C. Table 1.
Parameter RF CHARACTERISTICS Input Frequency RF Input Sensitivity Output Power Min 4 10 10 7 200 400 Typ Max 18 +10 5 2 330 660 1000 Phase Noise Reverse Leakage Second Harmonic Content Third Harmonic Content Fourth Harmonic Content Fifth Harmonic Content CE INPUT VIH, Input High Voltage VIL, Input Low Voltage POWER SUPPLIES Voltage Supply IDD (IDD1 + IDD2) Active Power-Down 150 60 38 12 20 19 2.2 0.3 3.0 3.3 30 7 3.6 60 25 Unit GHz dBm dBm dBm mV p-p mV p-p mV p-p dBc/Hz dBm dBc dBc dBc dBc V V V mA mA CE is high CE is low Test Conditions/Comments
4 GHz to 18 GHz Single-ended output connected into 50 load Differential outputs connected into 100 differential load Peak-to-peak voltage swing on each singleended output, connected into 50 load Peak-to-peak voltage swing on differential output, connected into 100 differential load Peak-to-peak voltage swing on each singleended output, no load condition Input frequency (fIN) = 12 GHz, offset = 100 kHz RF input power (PIN) = 0 dBm, RFOUT = 4 GHz
Rev. A | Page 3 of 12
This device is a high performance RF integrated circuit with an ESD rating of 2 kV, human body model (HBM) and is ESD sensitive. Proper precautions should be taken for handling and assembly.
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Rev. A | Page 4 of 12
PIN 1 INDICATOR
ADF5001
TOP VIEW (Not to Scale)
GND 8
GND 5
NC 6
CE 7
10 11 14 15 N/A 1
1
Rev. A | Page 5 of 12
08402-002
5 FIRST HARMONIC 10 15
POWER (dBm)
10
20
THIRD HARMONIC
30
40
35 40 2.4
10 15 FREQUENCY (GHz)
20
25
2.7
3.3
3.6
10
IDDx (mA)
12 10 8 6 4 2
08402-004
15
20
25
2.7
2.9
3.1
3.5
3.7
3.9
25
30
Figure 7. RFOUT Power vs. RFIN Frequency, fIN = 10 GHz, VDD = 3.3 V
20 2.5
Figure 5. RFOUT Power (Single-Ended) vs. VDDx, fIN = 10 GHz, PIN = 0 dBm
Rev. A | Page 6 of 12
08402-007
0 2.5
30
08402-006
60
08753-008
ROGERS RO4003C LAMINATE 0.008 Er = 3.38.STARTING COPPER WEIGHT 0.5oz/0.5oz 1.5oz (53m) FINISHED COPPER
08402-009
The evaluation board is powered from a single 3.0 V to 3.6 V supply, which should be connected to the J1 SMA connector. The power supply can also be connected using the T3 (VDDx) and T2 (GND) test points. The differential RF outputs are brought out on the J2 and J3 SMA connectors. If only one of the outputs is being used, the unused output should be correctly terminated using a 50 SMA termination. The chip enable (CE) pin can be controlled using the T1 test point. If this function is not required, the test point can remain unconnected.
BILL OF MATERIALS
Table 4.
Qty. 1 1 1 3 3 1 Reference Designator C1 C2 J4 J1, J2, J3 T1, T2, T3 U1 Description 0.1 F, 0603 capacitor 10 pF, 0402 capacitor 3.5 mm RF SMA connector 3.5 mm RF SMA connector Test points ADF5001 RF prescaler Supplier/Part Number Murata GRM188R71H104KA93D Murata GRM1555C1H100JZ01D Emerson 142-0761-801 Johnson Components 142-0701-851 Vero 20-2137 Analog Devices, Inc., ADF5001BCPZ
Rev. A | Page 7 of 12
VDD1
ADF4156
PLL RFINA RFINB 220 CP VP/2 820pF
RFIN
ADF5001
PRESCALER
OP184
OP AMP
1k
1F
1.8nF
6dB PAD 37 18
150
150
18
16GHz OUT
Figure 10. ADF5001 Used as the RF Prescaler in a Microwave 16 GHz PLL Loop
Rev. A | Page 8 of 12
08402-010
PIN 1 INDICATOR
0.25 MIN
BOTTOM VIEW FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET.
Figure 11. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 3 mm 3 mm Body, Very Very Thin Quad (CP-16-18) Dimensions shown in millimeters
ORDERING GUIDE
Model 1 ADF5001BCPZ ADF5001BCPZ-RL7 EVAL-ADF5001EB2Z
1
111808-A
Package Description 16-Lead Lead Frame Chip Scale Package (LFCSP_WQ) 16-Lead Lead Frame Chip Scale Package (LFCSP_WQ), 7 Tape and Reel Evaluation Board
Rev. A | Page 9 of 12
ADF5001 NOTES
Rev. A | Page 10 of 12
ADF5001 NOTES
Rev. A | Page 11 of 12
ADF5001 NOTES
20092010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08402-0-6/10(A)
Rev. A | Page 12 of 12