Escolar Documentos
Profissional Documentos
Cultura Documentos
Product Specification
Title
BUYER MODEL General
www.jxlcd.com www.jxlcd.com
*When you obtain standard approval, APPROVED BY / SIGNATURE DATE APPROVED BY H.S. Kim / G.Manager REVIEWED BY / D.I. Chung / Manager PREPARED BY / K.H. Lee / Engineer
please use the above model name without suffix SIGNATURE DATE
Please return 1 copy for your confirmation with your signature and comments.
Ver 0.0
July. 2. 2008
1 / 31
Product Specification
Contents
No
COVER CONTENTS RECORD OF REVISIONS 1 2 3 3-1 3-2 3-3 3-4 3-5 3-6 4 5 6 7 7-1 7-2 8 8-1 8-2 9 GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS ELECTRICAL CHARACTREISTICS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERNECE POWER SEQUENCE
ITEM
Page
1 2 3 4 5 6 6 8 12 13 14 15 17 23 26 27 27 27 28 28 28 29
OPTICAL SFECIFICATIONS
www.jxlcd.com www.jxlcd.com
MECHANICAL CHARACTERISTICS RELIABLITY INTERNATIONAL STANDARDS SAFETY EMC PACKING DESIGNATION OF LOT MARK PACKING FORM PRECAUTIONS
Ver 0.0
July. 2. 2008
2 / 31
Revision Date
July. 2. 2008
Page
First Draft(Preliminary)
Description
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
3 / 31
CN1
S1
S1920
LAMP
www.jxlcd.com www.jxlcd.com
CN 2 2pin x 8CNs (High)
General Features
Active Screen Size Outline Dimension Pixel Pitch Pixel Format Color Depth Luminance, White Viewing Angle(CR>10) Power Consumption Weight Display Operating Mode Surface Treatment Ver 0.0
Figure 1. Block diagram 27 inches(68.6cm) diagonal 630(H) x 368.2(V) x 37.2(D) mm(Typ.) *Without Inverter 0.3114 mm x 0.3114 mm 1920 horiz. By 1080 vert. Pixels RGB stripes arrangement 8-bit with A-FRC, 16,777,216 colors 400 cd/m2 (Center 1 point) View Angle Free (R/L 170(Typ.), U/D 160(Typ.)) Total 88.95 88 95 Watt (Typ (Typ.) ) ( 5.35 5 35 Watt @VLCD, 83.6 83 6 Watt @400cd/]) 4220 g (typ.) Transmissive mode, normally White
Hard coating(3H) & Anti-Glare treatment of the front polarizer
July. 2. 2008
4 / 31
Power Input Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity
C C
%RH %RH 1
Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 C Max, Max and no condensation of water. water
90%
40 40% 30 20 10 0 10% 10 20 30 40 50 60 70 80
www.jxlcd.com www.jxlcd.com
60 60% 50 Storage Operation -20 0 Dry Bulb Temperature [C]
Ver 0.0
July. 2. 2008
5 / 31
11.6
12.0
12.4
400 110
Differential Impedance
Power Supply Input Current
Power Consumption
Rush current
www.jxlcd.com www.jxlcd.com
IRUSH A
Note : 1. Permissive power ripple should be measured under VCC=12.0V, 25C, fV(frame frequency)=MAX condition and At that time, we recommend the bandwidth configuration of oscilloscope is to be under 20Mhz. See the next page. 2. The specified current and power consumption are under the VLCD=12.0V, 25 2C,fV=60Hz condition whereas Mosaic and max power pattern shown in the [ Figure 3 ] is displayed. 3. The current is specified at the maximum current pattern.
4. Maximum Condition of Inrush current : The duration of rush current is about 2ms and rising time of Input Voltage is 1ms(min.). At any rising time of Input voltage, Keep the I2T Value by below Condition Condition : I2T < 32*2ms
Ver 0.0
July. 2. 2008
6 / 31
Product Specification
White pattern
Black pattern
www.jxlcd.com www.jxlcd.com
Typical power Pattern Max power Pattern Figure g 3. Mosaic p pattern & Black Pattern for power p consumption p measurement
Ver 0.0
July. 2. 2008
7 / 31
Product Specification
Table 2_2. ELECTRICAL CHARACTERISTICS
Parameter LAMP : Operating Voltage Operating Current Established Starting Voltage VBL IBL Vs fBL Ts PBL 47.3 40,000 83.6 40 3000 3600 80 3.0 93.1 VRMS VRMS kHz Min Watt Hrs 4 1, 5 6 1, 7 1900(7.0mA) 3.0 1990(6.0mA) 6.0 2250(3.0mA) 7.0 VRMS mARMS 1, 2 1 1, 3 Symbol Values Min Typ Max Unit Notes
Note : The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly should be operated in the same condition as installed in you instrument. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.
www.jxlcd.com www.jxlcd.com
1. Specified values are for a single lamp. 2. Operating voltage is measured at 25 2C. The variance of the voltage is 10%. 3. The voltage above VS should be applied to the lamps for more than 1 second for start-up. (Inverter open voltage must be more than lamp starting voltage.) Otherwise the lamps may not be turned on. Otherwise, on The used lamp current is the lamp typical current. current 4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 5. Lets define the brightness of the lamp after being lighted for 5 minutes as 100%. TS is the time required for the brightness of the center of the lamp to be not less than 95%. 6. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (PBL = VBL x IBL x NLamp ) 7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial value l at t th the typical t i l lamp l current t on condition diti of f continuous ti operating ti at t 25 2C. C
Ver 0.0
July. 2. 2008
8 / 31
Product Specification
8. The output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform (Unsymmetrical ratio is less than 10%) 10%). Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and reduce leakage current. a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should be within 2 10%. * Inverter output waveform had better be more similar to ideal sine wave. * Asymmetry rate: Ip | I p I p | / Irms x 100% I -p * Distortion rate I p (or I p) / Irms 9. The inverter which is combined with this LCM, is highly recommended to connect coupling(ballast) condenser at the high voltage output side. When you use the inverter which has not coupling(ballast) condenser, it may cause abnormal lamp lighting because of biased mercury as time goes. 10.In case of edgy type back light with over 4 parallel lamps, input current and voltage wave form should be synchronized
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
9 / 31
No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Symbol
Description
Minus signal of odd channel 0 (LVDS) Plus signal of odd channel 0 (LVDS) Minus signal of odd channel 1 (LVDS) Plus signal of odd channel 1 (LVDS) Minus signal of odd channel 2 (LVDS) Plus signal of odd channel 2 (LVDS) Ground
No 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Symbol
Symbol
Plus signal of even channel 1 (LVDS) Ground Minus signal of even channel 2 (LVDS) Plus signal of even channel 2 (LVDS) Minus signal of even clock channel (LVDS) Plus signal of even clock channel (LVDS) Minus signal of even channel 3 (LVDS) Plus signal of even channel 3 (LVDS) Ground
www.jxlcd.com www.jxlcd.com
Minus signal of odd clock channel (LVDS) Plus signal of odd clock channel (LVDS) Minus signal of odd channel 3 (LVDS) Plus signal of odd channel 3 (LVDS) Minus signal of even channel 0 (LVDS) Plus signal of even channel 0 (LVDS) Ground Minus signal of even channel 1 (LVDS)
SR3P GND NC NC
No Connection No Connection Dynamic C/R output ODC Control (GND:DCR on, 3.3V:DCR off) Power Supply +12.0V Power Supply +12 +12.0V 0V
DCR_OUT
Note: 1. All GND(ground) pins should be connected together and to Vss which should also be connected to the LCDs metal frame. 2. All VLCD (power input) pins should be connected together. 3. Input Level of LVDS signal is based on the IEA 664 Standard. Rear view of LCM
#1 #1 #30 #30
10 / 31
Product Specification
Table 4. REQUIRED SIGNAL ASSIGNMENT FOR Flat Link (TI:SN75LVDS83) Transmitter Pin # Pin Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VCC D5 D6 D7 GND D8 D9 D10 VCC D11 D12 D13 GND D14 D15 D16 VCC D17 D18 D19 GND D20 D21 D22 D23 VCC D24 D25
Require Signal
Power Supply for TTL Input TTL Input (R7) TTL Input (R5) TTL Input (G0) Ground pin for TTL TTL Input (G1) TTL Input (G2) TTL Input (G6) Power Supply for TTL Input TTL Input (G7) TTL Input (G3) TTL Input (G4) Ground pin for TTL TTL Input (G5) TTL Input (B0) TTL Input (B6)
Pin #
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
Pin Name
GND D26 TX CLKIN PWR DWN PLL GND PLL VCC PLL GND LVDS GND TxOUT3 TxOUT3 TX CLKOUT TX CLKOUT TX OUT2 TX OUT2
Require Signal
Ground pin for TTL TTL Input (DE) TTL Level clock Input Power Down Input Ground pin for PLL Power Supply for PLL Ground pin for PLL Ground pin for LVDS Positive LVDS differential data output 3 Negative LVDS differential data output 3 Positive LVDS differential clock output Negative LVDS differential clock output Positive LVDS differential data output 2 Negative LVDS differential data output 2 Ground pin for LVDS
www.jxlcd.com www.jxlcd.com
LVDS GND LVDS VCC Power Supply for LVDS Power Supply for TTL Input TTL Input (B7) TTL Input (B1) TTL Input (B2) Ground pin for TTL Input TTL Input (B3) TTL Input (B4) TTL Input (B5) TTL Input (RSVD) Power Supply for TTL Input TTL Input (HSYNC) TTL Input (VSYNC) TX OUT1 TX OUT1 TX OUT0 TX OUT0 LVDS GND D27 D0 D1 GND D2 D3 D4 Ground pin for LVDS TTL Input (R6) TTL Input (R0) TTL Input (R1) Ground pin for TTL TTL Input (R2) TTL Input (R3) TTL Input (R4)
Positive LVDS differential data output 1 Negative LVDS differential data output 1 Positive LVDS differential data output 0 Negative LVDS differential data output 0
Ver 0.0
July. 2. 2008
11 / 31
Product Specification
Description LVDS Differential Voltage LVDS Common mode Voltage LVDS Input Voltage Range
Unit mV V V
Notes -
2. AC Specification
www.jxlcd.com www.jxlcd.com
Description Symbol tSKEW tSKEW tSKEW_EO FDEV FMOD Min - 400 - 600 - 1/7 Max + 400 + 600 + 1/7 3 200 Unit ps ps Tclk % KHz
LVDS Clock to Data Skew Margin LVDS Clock to Clock Skew Margin (Even to Odd) Maximum deviation of input clock frequency during SSC Maximum modulation frequency of input clock during SSC Ver 0.0
July. 2. 2008
12 / 31
Product Specification
www.jxlcd.com www.jxlcd.com
< Spread Spectrum >
Time
13 / 31
RCLK+
RA+/RB+/RC+/RD+/-
R 3 G4 B 5 G7
R2 G3 B 4 G6
R1 G2 B3 R7
R0 G1 B2 R6
G0 B 1 DE X
R5 B0
R4 G5
R3 G4 B5 G7
R2 G3 B4 G6
R1 G2 B 3 R7
R0 G1 B2 R6
G0 B1 DE X
R5 B0
R4 G5
VSYNC HSYNC B7 B6
VSYNC HSYNC B7 B6
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
14 / 31
Product Specification
Table 5. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN1,CN2,CN3,CN4,CN5,CN6, ( CN7) ) The backlight lamp connector is a model 1006-12102 (CN1/CN2/CN3/CN4/CN5/CN6/CN7) manufactured by C-NET. The mating connector part number are 1006-66202 (manufactured by C-NET) or equivalent. The pin configuration for the connector is shown in the table below.
Pin 1,2
Symbol y HV
NOTES 1
Note : 1. The high voltage power terminal is colored Red/White <BACKLIGHT CONNECTOR DIAGRAM>
www.jxlcd.com www.jxlcd.com
CN1 CN2 CN3 CN N4 CN5
U-LAMP
CN6 CN7 C
Ver 0.0
July. 2. 2008
15 / 31
Symbol
tCLK tC
Note
KH KHz tCLK
www.jxlcd.com www.jxlcd.com
Horizontal Front Porch Period
1090 1080 10 50 2 5 3
1100 1080 20 60 4 8 8
1160 1080 80 75 16 32 32
tHP tHP
Vertical Valid Vertical Blank Vsync Frequency Width Vertical Back Porch Vertical Front Porch
tHP Hz tHP
Note: Hsync period and Hsync width-active should be even number times of tCLK. If the value is odd number times of tCLK, display control signal can be asynchronous. In order to operate this LCM a Hsync, Vsyn, and DE(data enable) signals should be used. 1. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rates. 2 Vsync and Hsync should be keep the above specification 2. specification. 3. Hsync Period, Hsync Width, and Horizontal Back Porch should be any times of of character number(8). 4. The polarity of Hsync, Vsync is not restricted.
Ver 0.0
July. 2. 2008
16 / 31
0.7VDD 0.3VDD
tCLK
0.5VDD
www.jxlcd.com www.jxlcd.com
Data are latched at the falling edge of DCLK
tHP Hsync tWH tHBP DE(Data Enable) tVP tWV Vsync tVBP DE(Data Enable) tVV tVFP tHV tHFP
Ver 0.0
July. 2. 2008
17 / 31
Basic a Color
RED (000)
RED (001)
www.jxlcd.com www.jxlcd.com
1 1 1 1 1 1 1 1 1 1 1 1 Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ... ... 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 ... 0 0 Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 ... 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ... 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ... ... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 ... ... ...
RED
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
GREEN
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
BLUE
1 1
1 1
1 1
0 1
Ver 0.0
July. 2. 2008
18 / 31
90%
90%
10%
10%
T1 Interface signal VI
T2 Valid data
T5
T7
T8 T3 T4
T9
www.jxlcd.com www.jxlcd.com
OFF OFF
Values Min 0.5 0.01 500 200 0.01 500 0 < T8 < T2 0 < T9 < T5 Typ Max 10 50 50 Units ms ms ms ms ms ms ms ms
Lamp on
Notes : 1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD VLCDto 0V. 3. Lamp power must be turn on after power supply for LCD and interface signal are valid. Ver 0.0 July. 2. 2008
19 / 31
50cm FIG. 6 Optical Characteristic Measurement Equipment and Method T bl 9. Table 9 OPTICAL CHARACTERISTICS
Parameter Contrast Ratio Symbol CR
www.jxlcd.com www.jxlcd.com
LWH TrR cd/m2 % ms ms ms ms
WHITE
Rise Time
4 8 -
Response Time
BLUE WHITE
Viewing Angle (CR>10) x axis, right(=0) x axis, left (=180) y axis, up (=90) y axis, down (=270) Gray Scale r l u d
Ver 0.0
July. 2. 2008
20 / 31
Product Specification
Notes 1. Contrast Ratio(CR) is defined mathematically as : Contrast Ratio = Surface Luminance with all white pixels Surface Luminance with all black pixels
2. Surface luminance is luminance value at No.1 point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 6. 3. The variation in surface luminance , WHITE is defined as :
WHITE =
Measuring point for surface luminance & measuring point for luminance variation H A H/10
www.jxlcd.com www.jxlcd.com
2 3 4 B V 5 1 6 7 V/10 A : H/4 mm B : V/4 mm @ H,V : Active Area
Active Area
Ver 0.0
July. 2. 2008
21 / 31
Product Specification
4. The response time is defined as the following figure and shall be measured by switching th i the input t signal i lf for bl black k and d white. hit Response time is the time required for the display to transition from white to black (Rise Time, TrR) and from black to white (Decay Time, TrD). % 100 90 Optical response 10 0 white black white
TrR
TrD
5, The gray to gray response time is defined as the following figure and shall be measured by switching the input signal for Gray Gray To Gray Gray. - Gray step : 5 step - TGTG_AVR is the total average time at rising time and falling time for Gray To Gray. - TGTG_MAX is the max time at rising time or falling time for Gray To Gray.
www.jxlcd.com www.jxlcd.com
Gray to Gray G255 G191 Rising Time G255 G191 G127 G63
Falling Time
G127 G63 G0
Ver 0.0
July. 2. 2008
22 / 31
Product Specification
6. Viewing g angle g is the angle g at which the contrast ratio is g greater than 10 or 5. The angles g are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG. 9 . <Dimension of viewing angle range>
Normal E Y = 90, Up
= 180, Left
= 0, Right
www.jxlcd.com www.jxlcd.com
[ FIGURE 9 ] Viewing angle 7, Gray scale specification Gamma Value is approximately 2.2. For more information see Table 11 Table 11. Gray Scale Specification
Gray Level 0 31 63 95 127 159 191 223 255 Relative Luminance [%] (Typ.) 0.1 1.2 4.7 11.7 21.2 35.2 53.0 75.4 100
= 270, Down
Ver 0.0
July. 2. 2008
23 / 31
Notes : Please refer to a mechanic drawing in terms of tolerance at the next page.
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
24 / 31
Product Specification
<FRONT VIEW>
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
25 / 31
Product Specification
<REAR VIEW>
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
26 / 31
1 2 3 4
High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test
Ta= 60C 240h Ta= -20C 240h Ta= 50C 50%RH Ta= 0C 240h 240h
Wave form : random Vibration level : 1.0Grms Bandwidth : 10-300Hz Duration : X,Y,Z, 10min One time each direction Shock level : 100G Waveform : half sine wave, 2ms Direction : X, Y, Z One time each direction
Altitude
www.jxlcd.com www.jxlcd.com
Ta= 40 C ,90%RH storage / shipment 0 - 40,000 feet(12192m) Max 70%RH , Ta=40
Ver 0.0
July. 2. 2008
27 / 31
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. 40GHz American American National Standards Institute(ANSI), Institute(ANSI) 1992 b) C.I.S.P.R. Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. International Special Committee on Radio Interference. c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. European Committee for Electro technical Standardization.(CENELEC), 1998 ( Including A1: 2000 )
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
28 / 31
Note 1. YEAR
Year Mark 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0
2. MONTH
Month Mark Jan 1 Feb 2 Mar 3 Apr 4 May 5 Jun 6 Jul 7 Aug 8 Sep 9 Oct A Nov B Dec C
www.jxlcd.com www.jxlcd.com
Serial No. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.
Ver 0.0
July. 2. 2008
29 / 31
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
30 / 31
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5C and 35C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
www.jxlcd.com www.jxlcd.com
Ver 0.0
July. 2. 2008
31 / 31