Você está na página 1de 32

Selecting Die Springs

A general rule to observe in spring selection


is to always use as many springs as the die
will accommodate which will produce the
required load with the least amount of
deflection. This will increase the useful life of
the spring, reduce the chances of spring
failure and the resulting downtime, loss of
production and increased maintenance cost.
Die spring costs are a very small percentage
of the total cost of the die. An effort to save
a few cents on die springs is a misguided act
that can cost many dollars in lost time and
labor.
The more rapidly a spring works, the more
attention must be paid to its fatigue limits. In
slow moving dies or fixtures, it is possible to
get good performance with springs operating
near maximum deflection. As the working
speed increases, the life expectancy of the
spring at that deflection decreases
Springs for strippers, pressure pads, and
other die components can be selected from

the following pages. When selecting a die


spring it is necessary to determine the type of
performance required of the springs: short,
normal, or long run. For short or normal run
applications use the deflections tabulated in
the long life columns. For long run applications use deflections based on optimum life.
The recommended deflections for each spring
based on the performance required are
shown on pages 4 to 19.
Another approach when selecting a spring is
to work back from the amount of operating
travel the springs will be subjected to as
indicated by the die layout. Select springs in
the appropriate duty range which will operate
efficiently at the required travel. Calculate the
number of springs needed by dividing the
load supplied by one spring into the total load
required. Round the total number of springs
to the next higher even number for balanced
performance.

Die Spring Features & Benefits


Raymond Die Springs Offer

Features

Benefits

Superior Materials
& Wire Profile

All Raymond die springs are made from


vapor degassed high tensile strength
chromium alloy steels (chrome silicon).

Inherent toughness to withstand heavy


load demands.

Optimal wire cross section.

Superior performance in high stress


applications.

Spring ends are ground square.

Heat resistance up to 475F (250C).

Superior wire finish before and after


coiling.

Readily available, cost efficient raw


material.

Long cycle life.

Consistent controlled metallurgy.


Offers maximum design possibilities.
Wire cross section provides optimum
deflection and protection against failure
due to excessive stress build-up.
Square ends create reliable, flat, maximum
load-bearing surface.
Specialty materials available to meet
customer requirements.

Dimensional Consistency

Dimensional requirements remain


consistent and measurably the same from
one batch of springs to the next.

Provides uniform spring performance.


Insures consistent rate recordings.
Greater load accuracy at a given test
height.
Certainty that OD will work freely in
prescribed hole and ID will work freely
over prescribed rod.
Raymond assurance of the highest
production and quality standards.
Reliable performance engineered into
every Raymond die spring.

Longer Spring Life

Engineered to better withstand shock


loading.

Reliable, trouble-free performance.

Designed to endure constant high-speed


deflections.

Reduced spring breakage.

Increased fatigue life by as much as 30%.

Shot-peened to increase fatigue life.

Uniform performance over a longer


lifetime.

Less downtime.

More cost effective.


Extra performance margins.

Excellent Deflection

Springs provide greater available travel to


solid.
Each spring is preset during manufacture.

More travel in each spring.


Higher load capacities.
Increased fatigue life.
Greater application flexibility.
More reliable performance.
Lower solid height.
No loss of free length in application.

Proper Die Spring Application


The most common die spring problems are generally the most basic the result of improper selection and application. But trying to save a few pennies on die springs or a few minutes on selection can result in enormous expenses in terms of premature spring failure, increased maintenance costs and lost productivity. That's why making
sure you have the best die spring for every application is truly a wise investment.
DO make spring selection a part of the early design function, and work within the spring's physical limits. It's
best to determine which springs and how many are needed for the job before the die is built.

DO preload each spring into the assembled tool to prevent the possibility of shock loading, which causes a stress
surge in the vibration frequency and may result in early spring failure.

Do provide safeguards from adverse external elements such as heat, corrosive atmosphere, metal chips and
other obstructions

DO provide proper guidance on all springs to reduce the chance of buckling. As a general rule, if the free length
is more than four times the mean diameter of the spring, it could have a buckling problem under compression.
This is solved by using a guide rod, boring a pocket, or both.

DO deepen spring pockets proportionately when the die is sharpened to maintain the same spring travel and load
level. Each spring pocket needs to have a flat bottom and square corners, so the spring will provide uniform
stress on each coil as it is compressed.

DO perform preventative maintenance on a regularly scheduled basis. Keep records on the number of cycles
each die performs, and replace all the die springs at predetermined intervals.

DON'T replace only one spring, or mix springs of assorted lengths and deflection ranges on a die. Instead of
using an unbalanced, mixed assembly of old and new springs, replace all of the springs to distribute the load
evenly.

DON'T alter a die spring by cutting off coils or grinding the inside or outside diameter. Altering a die spring
causes early failure and creates the potential for damaging the die.

DON'T expect maximum performance life from a spring that is producing at maximum load. Although die springs
are designed to produce maximum load, they are highly stressed when maximum loads are met.

DON'T wait make spring selection a part of the early design function, and work within the spring's physical
limits. It's best to determine which springs and how many are needed for the job before the die is built.

DO call our knowledgeable customer service and engineering professionals are always available to assist you
with everything from custom sizes and special materials to technical questions and unusual applications.

Deflection To Compressed Length Conversion Tables


Die Springs - Inch Tables
Free
Length
(in)
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
6 1/2
7
7 1/2
8
10
12

Medium Duty
Compressed Length (in)
Deflection in % free length

Medium Heavy Duty


Compressed Length (in)

Heavy Duty
Compressed Length (in)

Extra Heavy Duty


Compressed Length (in)

Deflection in % free length

Deflection in % free length

Deflection in % free length

25%

35%

40%

20%

25%

30%

15%

20%

25%

15%

0.75
0.94
1.13
1.31
1.50
1.88
2.25
2.63
3.00
3.38
3.75
4.13
4.50
4.88
5.25
5.63
6.00
7.50
9.00

0.65
0.81
0.98
1.14
1.30
1.63
1.95
2.28
2.60
2.93
3.25
3.58
3.90
4.23
4.55
4.88
5.20
6.50
7.80

0.60
0.75
0.90
1.05
1.20
1.50
1.80
2.10
2.40
2.70
3.00
3.30
3.60
3.90
4.20
4.50
4.80
6.00
7.20

0.80
1.00
1.20
1.40
1.60
2.00
2.40
2.80
3.20
3.60
4.00
4.40
4.80
5.20
5.60
6.00
6.40
8.00
9.60

0.75
0.94
1.13
1.31
1.50
1.88
2.25
2.63
3.00
3.38
3.75
4.13
4.50
4.88
5.25
5.63
6.00
7.50
9.00

0.70
0.88
1.05
1.23
1.40
1.75
2.10
2.45
2.80
3.15
3.50
3.85
4.20
4.55
4.90
5.25
5.60
7.00
8.40

0.85
1.06
1.28
1.49
1.70
2.13
2.55
2.98
3.40
3.83
4.25
4.68
5.10
5.53
5.95
6.38
6.80
8.50
10.20

0.80
1.00
1.20
1.40
1.60
2.00
2.40
2.80
3.20
3.60
4.00
4.40
4.80
5.20
5.60
6.00
6.40
8.00
9.60

0.75
0.94
1.13
1.31
1.50
1.88
2.25
2.63
3.00
3.38
3.75
4.13
4.50
4.88
5.25
5.63
6.00
7.50
9.00

0.85
1.06
1.28
1.49
1.70
2.13
2.55
2.98
3.40
3.83
4.25
4.68
5.10
5.53
5.95
6.38
6.80
8.50
10.20

17%

0.83
1.04
1.25
1.45
1.66
2.08
2.49
2.91
3.32
3.74
4.15
4.57
4.98
5.40
5.81
6.23
6.64
8.30
9.96

20%

0.80
1.00
1.20
1.40
1.60
2.00
2.40
2.80
3.20
3.60
4.00
4.40
4.80
5.20
5.60
6.00
6.40
8.00
9.60

Die Springs - Metric Tables


Free
Length
(mm)
25
32
38
44
51
64
76
89
102
114
127
140
152
165
178
191
203
254
305

Medium Duty
Compressed Length (mm)
Deflection in % free length
25%

19
24
29
33
38
48
57
67
76
86
95
105
114
124
133
143
152
191
229

35%

17
21
25
29
33
41
50
58
66
84
83
91
99
107
116
124
132
165
198

Medium Heavy Duty


Compressed Length (mm)

Heavy Duty
Compressed Length (mm)

Deflection in % free length

40%

20%

15
19
23
27
30
38
46
53
61
69
76
84
91
99
107
114
122
152
183

20
25
30
36
41
51
61
71
81
91
102
112
122
132
142
152
163
203
244

25%

19
24
29
33
38
48
57
67
76
86
95
105
114
124
133
143
152
191
229

30%

18
22
27
31
36
44
53
62
71
80
89
98
107
116
124
133
142
178
213

Extra Heavy Duty


Compressed Length (mm)

Deflection in % free length


15%

22
27
32
38
43
54
65
76
86
97
108
119
130
140
151
162
173
216
259

20%

20
25
30
36
41
51
61
71
81
91
102
112
122
132
142
152
163
203
244

25%

19
24
29
33
38
48
57
67
76
86
95
105
114
124
133
143
152
191
229

Deflection in % free length


15%

22
27
32
38
43
54
65
76
86
97
108
119
130
140
151
162
173
216
259

17%

20%

21
26
32
37
42
53
63
74
84
95
105
116
126
137
148
158
169
211
253

20
25
30
36
41
51
61
71
81
91
102
112
122
132
142
152
163
203
244

MEDIUM DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

3/8

3/16

1/2

9/32

5/8

11/32

3/4

3/8

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4 1/2
5 1/2
6 1/2
7 1/2
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
6 1/2
7 1/2
12

CATALOG
NUMBER

103-104
103-105
103-106
103-107
103-108
103-110
103-112
103-148
103-204
103-205
103-206
103-207
103-208
103-210
103-212
103-214
103-218
103-222
103-226
103-230
103-248
103-304
103-305
103-306
103-307
103-308
103-310
103-312
103-314
103-316
103-348
103-404
103-405
103-406
103-407
103-408
103-410
103-412
103-414
103-416
103-418
103-420
103-422
103-424
103-426
103-430
103-448

Load at
1/10 in.
Def.
(lb)

6.0
5.4
4.0
3.4
2.8
2.4
2.1
0.6
11.0
8.2
6.8
6.0
5.5
4.5
3.5
3.0
2.5
2.1
1.4
1.2
0.7
16.4
12.8
10.8
9.6
8.8
6.0
5.6
4.8
4.4
1.6
31.2
25.6
20.0
17.6
14.4
12.0
9.6
8.0
7.2
6.4
6.0
5.5
5.0
4.5
3.8
2.4

INCH DIMENSIONS

For Optimum Life


(25% of free length)

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(35% of free length)
(40% of free length)

Load (lb)

Deflection (in)

Load (lb)

Deflection (in)

15.0
16.9
15.0
14.9
14.0
15.0
15.8
18.0
27.5
25.6
25.5
26.3
27.5
28.1
26.3
26.3
28.1
28.9
22.8
22.5
21.0
41.0
40.0
40.5
42.0
44.0
37.5
42.0
42.0
44.0
48.0
78.0
80.0
75.0
77.0
72.0
75.0
72.0
70.0
72.0
72.0
75.0
75.6
75.0
73.1
71.3
72.0

0.25
0.31
0.38
0.44
0.50
0.63
0.75
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.13
1.38
1.63
1.88
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.63
1.88
3.00

21.0
23.6
21.0
20.8
19.6
21.0
22.0
25.2
38.5
35.9
35.7
36.8
38.5
39.4
36.8
36.8
39.4
40.4
31.9
31.5
29.4
57.4
56.0
56.7
58.8
61.6
52.5
58.8
58.8
61.6
67.2
109.2
112.0
105.0
107.8
100.8
105.0
100.8
98.0
100.8
100.8
105.0
105.9
105.0
102.4
99.8
100.8

0.35
0.44
0.53
0.61
0.70
0.88
1.05
4.20
0.35
0.44
0.53
0.61
0.70
0.88
1.05
1.23
1.58
1.93
2.28
2.63
4.20
0.35
0.44
0.53
0.61
0.70
0.88
1.05
1.23
1.40
4.20
0.35
0.44
0.53
0.61
0.70
0.88
1.05
1.23
1.40
1.58
1.75
1.93
2.10
2.28
2.63
4.20

Load (lb)

24.0
27.0
24.0
23.8
22.4
24.0
25.2
28.8
44.0
41.0
40.8
42.0
44.0
45.0
42.0
42.0
45.0
46.2
36.4
36.0
33.6
65.6
64.0
64.8
67.2
70.4
60.0
67.2
67.2
70.4
76.8
124.8
128.0
120.0
123.2
115.2
120.0
115.2
112.0
115.2
115.2
120.0
121.0
120.0
117.0
114.0
115.2

Deflection (in)

0.40
0.50
0.60
0.70
0.80
1.00
1.20
4.80
0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
1.80
2.20
2.60
3.00
4.80
0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
1.60
4.80
0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.60
3.00
4.80

BLUE
*Maximum Deflection
(50% of free length)
Deflection (in)

0.50
0.63
0.75
0.88
1.00
1.25
1.50
6.00
0.50
0.63
0.75
0.88
1.00
1.25
1.50
1.75
2.25
2.75
3.25
3.75
6.00
0.50
0.63
0.75
0.88
1.00
1.25
1.50
1.75
2.00
6.00
0.50
0.63
0.75
0.88
1.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.75
6.00

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color blue is a registered trademark of Barnes Group Inc.

MEDIUM DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

1/2

1 1/4

5/8

1 1/2

3/4

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
12
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12

CATALOG
NUMBER

Load at
1/10 in.
Def.
(lb)

103-504
103-505
103-506
103-507
103-508
103-510
103-512
103-514
103-516
103-518
103-520
103-522
103-524
103-528
103-532
103-548
103-606
103-607
103-608
103-610
103-612
103-614
103-616
103-618
103-620
103-622
103-624
103-628
103-632
103-640
103-648
103-708
103-710
103-712
103-714
103-716
103-718
103-720
103-722
103-724
103-728
103-732
103-740
103-748
103-810
103-812
103-814
103-816
103-818
103-820
103-822
103-824
103-828
103-832
103-840
103-848

55.0
45.0
35.0
30.0
26.0
20.0
16.5
15.0
12.0
10.4
9.6
8.8
8.0
7.2
6.0
4.0
49.6
42.4
35.2
28.8
24.0
20.0
17.6
16.0
13.6
12.8
12.0
10.4
8.8
7.2
6.0
53.0
45.0
36.0
30.0
27.0
23.0
21.0
18.5
17.0
14.5
12.8
10.0
8.0
100.0
83.0
64.8
60.0
53.0
47.0
39.2
39.0
31.2
28.5
20.8
17.5

INCH DIMENSIONS

For Optimum Life


(25% of free length)

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(35% of free length)
(40% of free length)

BLUE
*Maximum Deflection
(50% of free length)

Load (lb)

Deflection (in)

Load (lb)

Deflection (in)

Load (lb)

Deflection (in)

Deflection (in)

137.5
140.6
131.3
131.3
130.0
125.0
123.8
131.3
120.0
117.0
120.0
121.0
120.0
126.0
120.0
120.0
186.0
185.5
176.0
180.0
180.0
175.0
176.0
180.0
170.0
176.0
180.0
182.0
176.0
180.0
180.0
265.0
281.3
270.0
262.5
270.0
258.8
262.5
254.4
255.0
253.8
256.0
250.0
240.0
625.0
622.5
567.0
600.0
596.3
587.5
539.0
585.0
546.0
570.0
520.0
525.0

0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
3.00
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00

192.5
196.9
183.8
183.8
182.0
175.0
173.3
183.8
168.0
163.8
168.0
169.4
168.0
176.4
168.0
168.0
260.4
259.7
246.4
252.0
252.0
245.0
246.4
252.0
238.0
246.4
252.0
254.8
246.4
252.0
252.0
371.0
393.8
378.0
367.5
378.0
362.3
367.5
356.1
357.0
355.3
358.4
350.0
336.0
875.0
871.5
793.8
840.0
834.8
822.5
754.6
819.0
764.4
798.0
728.0
735.0

0.35
0.44
0.53
0.61
0.70
0.88
1.05
1.23
1.40
1.58
1.75
1.93
2.10
2.45
2.80
4.20
0.53
0.61
0.70
0.88
1.05
1.23
1.40
1.58
1.75
1.93
2.10
2.45
2.80
3.50
4.20
0.70
0.88
1.05
1.23
1.40
1.58
1.75
1.93
2.10
2.45
2.80
3.50
4.20
0.88
1.05
1.23
1.40
1.58
1.75
1.93
2.10
2.45
2.80
3.50
4.20

220.0
225.0
210.0
210.0
208.0
200.0
198.0
210.0
192.0
187.2
192.0
193.6
192.0
201.6
192.0
192.0
297.6
296.8
281.6
288.0
288.0
280.0
281.6
288.0
272.0
281.6
288.0
291.2
281.6
288.0
288.0
424.0
450.0
432.0
420.0
432.0
414.0
420.0
407.0
408.0
406.0
409.6
400.0
384.0
1000.0
996.0
907.2
960.0
954.0
940.0
862.4
936.0
873.6
912.0
832.0
840.0

0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.80
3.20
4.80
0.60
0.70
0.80
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.80
3.20
4.00
4.80
0.80
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.80
3.20
4.00
4.80
1.00
1.20
1.40
1.60
1.80
2.00
2.20
2.40
2.80
3.20
4.00
4.80

0.50
0.63
0.75
0.88
1.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.50
4.00
6.00
0.75
0.88
1.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.50
4.00
5.00
6.00
1.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.50
4.00
5.00
6.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.50
4.00
5.00
6.00

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color blue is a registered trademark of Barnes Group Inc.

MEDIUM HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

3/8

3/16

1/2

9/32

5/8

11/32

3/4

3/8

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
12

CATALOG
NUMBER

104-104
104-105
104-106
104-107
104-108
104-110
104-112
104-148
104-204
104-205
104-206
104-207
104-208
104-210
104-212
104-214
104-248
104-304
104-305
104-306
104-307
104-308
104-310
104-312
104-314
104-316
104-348
104-404
104-405
104-406
104-407
104-408
104-410
104-412
104-414
104-416
104-418
104-420
104-422
104-424
104-448

Load at
1/10 in.
Def.
(lb)

9.0
7.3
6.7
5.8
5.0
4.2
3.0
0.9
16.8
13.0
9.5
8.5
7.5
6.0
5.7
4.0
1.2
30.0
21.5
19.0
16.8
14.8
11.5
10.0
8.5
7.6
2.7
50.0
38.0
32.0
28.8
24.8
19.2
14.4
12.8
12.0
11.2
9.0
8.0
7.5
3.6

For Optimum Life


(20% of free length)

INCH DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(25% of free length)
(30% of free length)

Load (lb)

Deflection (in)

Load (lb)

Deflection (in)

18.0
18.3
20.1
20.3
20.0
21.0
18.0
21.6
33.6
32.5
28.5
29.8
30.0
30.0
34.2
28.0
28.8
60.0
53.8
57.0
58.8
59.2
57.5
60.0
59.5
60.8
64.8
100.0
95.0
96.0
100.8
99.2
96.0
86.4
89.6
96.0
100.8
90.0
88.0
90.0
86.4

0.20
0.25
0.30
0.35
0.40
0.50
0.60
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
2.40

22.5
22.8
25.1
25.4
25.0
26.3
22.5
27.0
42.0
40.6
35.6
37.2
37.5
37.5
42.8
35.0
36.0
75.0
67.2
71.3
73.5
74.0
71.9
75.0
74.4
76.0
81.0
125.0
118.8
120.0
126.0
124.0
120.0
108.0
112.0
120.0
126.0
112.5
110.0
112.5
108.0

0.25
0.31
0.38
0.44
0.50
0.63
0.75
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
3.00

Load (lb)

27.0
27.4
30.2
30.5
30.0
31.5
27.0
32.4
50.4
48.8
42.8
44.6
45.0
45.0
51.3
42.0
43.2
90.0
80.6
85.5
88.2
88.8
86.3
90.0
89.3
91.2
97.2
150.0
142.5
144.0
151.2
148.8
144.0
129.6
134.4
144.0
151.2
135.0
132.0
135.0
129.6

Deflection (in)

0.30
0.38
0.45
0.53
0.60
0.75
0.90
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
3.60

RED
*Maximum Deflection
(37% of free length)
Deflection (in)

0.37
0.46
0.56
0.65
0.74
0.93
1.11
4.44
0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
4.44
0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
1.48
4.44
0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
1.48
1.67
1.85
2.04
2.22
4.44

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color red is a registered trademark of Barnes Group Inc.

MEDIUM HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

1/2

1 1/4

5/8

1 1/2

3/4

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
12
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12

CATALOG
NUMBER

Load at
1/10 in.
Def.
(lb)

104-504
104-505
104-506
104-507
104-508
104-510
104-512
104-514
104-516
104-518
104-520
104-522
104-524
104-528
104-532
104-548
104-606
104-607
104-608
104-610
104-612
104-614
104-616
104-618
104-620
104-622
104-624
104-628
104-632
104-640
104-648
104-708
104-710
104-712
104-714
104-716
104-718
104-720
104-722
104-724
104-728
104-732
104-740
104-748
104-810
104-812
104-814
104-816
104-818
104-820
104-822
104-824
104-828
104-832
104-840
104-848

76.0
62.4
49.6
44.0
40.0
31.0
25.0
21.6
18.4
17.0
14.4
12.8
12.0
10.0
8.8
6.2
114.4
100.8
86.4
62.4
51.2
44.0
36.8
32.0
29.0
26.4
25.0
20.0
18.4
14.5
12.4
108.0
85.6
62.4
52.8
48.0
43.2
36.8
34.4
30.4
26.4
22.0
17.6
14.4
118.4
96.0
80.0
66.4
60.0
56.0
50.4
47.2
40.0
35.2
26.0
22.4

For Optimum Life


(20% of free length)
Load (lb)

152.0
156.0
148.8
154.0
160.0
155.0
150.0
151.2
147.2
153.0
144.0
140.8
144.0
140.0
140.8
148.8
343.2
352.8
345.6
312.0
307.2
308.0
294.4
288.0
290.0
290.4
300.0
280.0
294.4
290.0
297.6
432.0
428.0
374.4
369.6
384.0
388.8
368.0
378.4
364.8
369.6
352.0
352.0
345.6
592.0
576.0
560.0
531.2
540.0
560.0
554.4
566.4
560.0
563.2
520.0
537.6

Deflection (in)

0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.40
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40

INCH DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(25% of free length)
(30% of free length)
Load (lb)

190.0
195.0
186.0
192.5
200.0
193.8
187.5
189.0
184.0
191.3
180.0
176.0
180.0
175.0
176.0
186.0
429.0
441.0
432.0
390.0
384.0
385.0
368.0
360.0
362.5
363.0
375.0
350.0
368.0
362.5
372.0
540.0
535.0
468.0
462.0
480.0
486.0
460.0
473.0
456.0
462.0
440.0
440.0
432.0
740.0
720.0
700.0
664.0
675.0
700.0
693.0
708.0
700.0
704.0
650.0
672.0

Deflection (in)

0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
3.00
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00

Load (lb)

Deflection (in)

228.0
234.0
223.2
231.0
240.0
232.5
225.0
226.8
220.8
229.5
216.0
211.2
216.0
210.0
211.2
223.2
514.8
529.2
518.4
468.0
460.8
462.0
441.6
432.0
435.0
435.6
450.0
420.0
441.6
435.0
446.4
648.0
642.0
561.6
554.4
576.0
583.2
552.0
567.6
547.2
554.4
528.0
528.0
518.4
888.0
864.0
840.0
796.8
810.0
840.0
831.6
849.6
840.0
844.8
780.0
806.4

0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.60
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60

RED
*Maximum Deflection
(37% of free length)
Deflection (in)

0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
1.48
1.67
1.85
2.04
2.22
2.59
2.96
4.44
0.56
0.65
0.74
0.93
1.11
1.30
1.48
1.67
1.85
2.04
2.22
2.59
2.96
3.70
4.44
0.74
0.93
1.11
1.30
1.48
1.67
1.85
2.04
2.22
2.59
2.96
3.70
4.44
0.93
1.11
1.30
1.48
1.67
1.85
2.04
2.22
2.59
2.96
3.70
4.44

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color red is a registered trademark of Barnes Group Inc.

HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

3/8

3/16

1/2

9/32

5/8

11/32

3/4

3/8

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
12

CATALOG
NUMBER

105-104
105-105
105-106
105-107
105-108
105-110
105-112
105-148
105-204
105-205
105-206
105-207
105-208
105-210
105-212
105-214
105-248
105-304
105-305
105-306
105-307
105-308
105-310
105-312
105-314
105-316
105-348
105-404
105-405
105-406
105-407
105-408
105-410
105-412
105-414
105-416
105-418
105-420
105-422
105-424
105-448

Load at
1/10 in.
Def.
(lb)

11.0
9.8
8.0
8.4
7.2
5.5
4.2
1.2
23.6
18.6
15.5
13.8
11.0
8.4
7.4
6.0
1.6
42.4
29.6
27.2
24.0
20.8
17.0
14.4
12.2
10.8
3.0
108.0
88.0
65.6
60.0
49.6
40.0
34.0
28.0
25.0
22.0
19.5
17.0
16.0
8.0

INCH DIMENSIONS

For Optimum Life


(15% of free length)
Load (lb)

16.5
18.4
18.0
22.1
21.6
20.6
18.9
21.6
35.4
34.9
34.9
36.2
33.0
31.5
33.3
31.5
28.8
63.6
55.5
61.2
63.0
62.4
63.8
64.8
64.1
64.8
54.0
162.0
165.0
147.6
157.5
148.8
150.0
153.0
147.0
150.0
148.5
146.3
140.3
144.0
144.0

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(20% of free length)
(25% of free length)

Deflection (in)

Load (lb)

Deflection (in)

0.15
0.19
0.23
0.26
0.30
0.38
0.45
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
0.60
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.80

22.0
24.5
24.0
29.4
28.8
27.5
25.2
28.8
47.2
46.5
46.5
48.3
44.0
42.0
44.4
42.0
38.4
84.8
74.0
81.6
84.0
83.2
85.0
86.4
85.4
86.4
72.0
216.0
220.0
196.8
210.0
198.4
200.0
204.0
196.0
200.0
198.0
195.0
187.0
192.0
192.0

0.20
0.25
0.30
0.35
0.40
0.50
0.60
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
2.40

Load (lb)

27.5
30.6
30.0
36.8
36.0
34.4
31.5
36.0
59.0
58.1
58.1
60.4
55.0
52.5
55.5
52.5
48.0
106.0
92.5
102.0
105.0
104.0
106.3
108.0
106.8
108.0
90.0
270.0
275.0
246.0
262.5
248.0
250.0
255.0
245.0
250.0
247.5
243.8
233.8
240.0
240.0

Deflection (in)

0.25
0.31
0.38
0.44
0.50
0.63
0.75
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
3.00

GOLD
*Maximum Deflection
(30% of free length)
Deflection (in)

0.30
0.38
0.45
0.53
0.60
0.75
0.90
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
3.60

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color gold is a registered trademark of Barnes Group Inc.

HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

1/2

1 1/4

5/8

1 1/2

3/4

Free
Length
(in)

CATALOG
NUMBER

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
12
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
7
8
10
12

105-504
105-505
105-506
105-507
105-508
105-510
105-512
105-514
105-516
105-518
105-520
105-522
105-524
105-528
105-532
105-548
105-606
105-607
105-608
105-610
105-612
105-614
105-616
105-618
105-620
105-622
105-624
105-628
105-632
105-640
105-648
105-708
105-710
105-712
105-714
105-716
105-718
105-720
105-722
105-724
105-728
105-732
105-740
105-748
105-810
105-812
105-814
105-816
105-818
105-820
105-822
105-824
105-828
105-832
105-840
105-848

Load at
1/10 in.
Def.
(lb)

208.0
171.2
118.4
104.0
90.0
68.0
54.4
45.6
40.0
35.2
31.2
28.8
25.6
22.4
19.2
12.0
212.0
181.6
149.6
117.6
95.2
75.2
66.4
58.4
53.0
47.2
42.4
36.8
32.8
25.6
20.8
190.4
155.0
130.0
106.4
91.2
78.4
71.2
64.0
58.4
49.6
43.2
34.4
28.8
260.0
200.0
170.0
150.0
120.0
110.0
100.0
94.0
82.0
73.0
55.0
42.0

INCH DIMENSIONS

GOLD

LOAD DEFLECTION TABLE


For Optimum Life
(15% of free length)
Load (lb)

312.0
321.0
266.4
273.0
270.0
255.0
244.8
239.4
240.0
237.6
234.0
237.6
230.4
235.2
230.4
216.0
477.0
476.7
448.8
441.0
428.4
394.8
398.4
394.2
397.5
389.4
381.6
386.4
393.6
384.0
374.4
571.2
581.3
585.0
558.6
547.2
529.2
534.0
528.0
525.6
520.8
518.4
516.0
518.4
975.0
900.0
892.5
900.0
810.0
825.0
825.0
846.0
861.0
876.0
825.0
756.0

Deflection (in)

0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.05
1.20
1.80
0.23
0.26
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.05
1.20
1.50
1.80
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.05
1.20
1.50
1.80
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.05
1.20
1.50
1.80

For Long Life


(20% of free length)
Load (lb)

416.0
428.0
355.2
364.0
360.0
340.0
326.4
319.2
320.0
316.8
312.0
316.8
307.2
313.6
307.2
288.0
636.0
635.6
598.4
588.0
571.2
526.4
531.2
525.6
530.0
519.2
508.8
515.2
524.8
512.0
499.2
761.6
775.0
780.0
744.8
729.6
705.6
712.0
704.0
700.8
694.4
691.2
688.0
691.2
1300.0
1200.0
1190.0
1200.0
1080.0
1100.0
1100.0
1128.0
1148.0
1168.0
1100.0
1008.0

Deflection (in)

0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.40
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.40
1.60
2.00
2.40

Maximum Operating Def.


(25% of free length)
Load (lb)

Deflection (in)

520.0
535.0
444.0
455.0
450.0
425.0
408.0
399.0
400.0
396.0
390.0
396.0
384.0
392.0
384.0
360.0
795.0
794.5
748.0
735.0
714.0
658.0
664.0
657.0
662.5
649.0
636.0
644.0
656.0
640.0
624.0
952.0
968.8
975.0
931.0
912.0
882.0
890.0
880.0
876.0
868.0
864.0
860.0
864.0
1625.0
1500.0
1487.5
1500.0
1350.0
1375.0
1375.0
1410.0
1435.0
1460.0
1375.0
1260.0

0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
3.00
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
1.75
2.00
2.50
3.00

*Maximum Deflection
(30% of free length)
Deflection (in)

0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.60
0.45
0.53
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60
0.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60
0.75
0.90
1.05
1.20
1.35
1.50
1.65
1.80
2.10
2.40
3.00
3.60

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color gold is a registered trademark of Barnes Group Inc.

EXTRA HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

Free
Length
(in)

3/8

3/16

1/2

9/32

5/8

11/32

3/4

3/8

1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
12
1
1 1/4
1 1/2
1 3/4
2
2 1/2
3
3 1/2
4
4 1/2
5
5 1/2
6
12

CATALOG
NUMBER

106-104
106-105
106-106
106-107
106-108
106-110
106-112
106-148
106-204
106-205
106-206
106-207
106-208
106-210
106-212
106-214
106-248
106-304
106-305
106-306
106-307
106-308
106-310
106-312
106-314
106-316
106-348
106-404
106-405
106-406
106-407
106-408
106-410
106-412
106-414
106-416
106-418
106-420
106-422
106-424
106-448

Load at
1/10 in.
Def.
(lb)

22.0
16.0
12.5
11.5
9.0
7.0
6.5
1.5
32.0
24.0
20.0
17.0
14.0
11.5
9.0
8.0
2.5
63.0
47.0
38.0
32.0
29.0
22.0
19.0
16.0
13.5
4.5
140.0
110.0
89.0
75.0
68.0
50.0
40.5
34.5
30.0
26.5
23.5
21.5
19.5
9.5

For Optimum Life


(15% of free length)
Load (lb)

33.0
30.0
28.1
30.2
27.0
26.3
29.3
27.0
48.0
45.0
45.0
44.6
42.0
43.1
40.5
42.0
45.0
94.5
88.1
85.5
84.0
87.0
82.5
85.5
84.0
81.0
81.0
210.0
206.3
200.3
196.9
204.0
187.5
182.3
181.1
180.0
178.9
176.3
177.4
175.5
171.0

Deflection (in)

0.15
0.19
0.23
0.26
0.30
0.38
0.45
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
0.60
1.80
0.15
0.19
0.23
0.26
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.83
0.90
1.80

INCH DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(17% of free length)
(20% of free length)
Load (lb)

Deflection (in)

37.4
34.0
31.9
34.2
30.6
29.8
33.2
30.6
54.4
51.0
51.0
50.6
47.6
48.9
45.9
47.6
51.0
107.1
99.9
96.9
95.2
98.6
93.5
96.9
95.2
91.8
91.8
238.0
233.8
227.0
223.1
231.2
212.5
206.6
205.3
204.0
202.7
199.8
201.0
198.9
193.8

0.17
0.21
0.26
0.30
0.34
0.43
0.51
2.04
0.17
0.21
0.26
0.30
0.34
0.43
0.51
0.60
2.04
0.17
0.21
0.26
0.30
0.34
0.43
0.51
0.60
0.68
2.04
0.17
0.21
0.26
0.30
0.34
0.43
0.51
0.60
0.68
0.77
0.85
0.94
1.02
2.04

Load (lb)

44.0
40.0
37.5
40.3
36.0
35.0
39.0
36.0
64.0
60.0
60.0
59.5
56.0
57.5
54.0
56.0
60.0
126.0
117.5
114.0
112.0
116.0
110.0
114.0
112.0
108.0
108.0
280.0
275.0
267.0
262.5
272.0
250.0
243.0
241.5
240.0
238.5
235.0
236.5
234.0
228.0

Deflection (in)

0.20
0.25
0.30
0.35
0.40
0.50
0.60
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
2.40
0.20
0.25
0.30
0.35
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
2.40

GREEN
*Maximum Deflection
(25% of free length)
Deflection (in)

0.25
0.31
0.38
0.44
0.50
0.63
0.75
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
3.00
0.25
0.31
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
3.00

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color green is a registered trademark of Barnes Group Inc.

10

EXTRA HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(in)

Rod
Dia.
(in)

1/2

1 1/4

5/8

1 1/2

3/4

Free
Length
(in)

CATALOG
NUMBER

Load at
1/10 in.
Def.
(lb)

106-506
106-508
106-510
106-512
106-514
106-516
106-518
106-520
106-524
106-548
106-608
106-610
106-612
106-614
106-616
106-618
106-620
106-624
106-632
106-640
106-648
106-708
106-710
106-712
106-714
106-716
106-718
106-720
106-724
106-732
106-740
106-748
106-810
106-812
106-814
106-816
106-818
106-820
106-824
106-832
106-840
106-848

160.0
116.0
89.6
73.6
62.4
55.2
48.8
43.2
36.0
17.6
192.0
144.0
118.4
100.8
84.0
78.4
68.0
56.0
41.6
33.6
26.4
376.0
294.4
231.2
196.0
171.2
148.0
136.0
110.4
80.8
67.2
54.4
381.6
312.0
254.4
220.0
188.8
172.8
141.6
100.0
84.0
71.2

1 1/2
2
2 1/2
3
3 1/2
4
4 1/2
5
6
12
2
2 1/2
3
3 1/2
4
4 1/2
5
6
8
10
12
2
2 1/2
3
3 1/2
4
4 1/2
5
6
8
10
12
2 1/2
3
3 1/2
4
4 1/2
5
6
8
10
12

INCH DIMENSIONS

GREEN

LOAD DEFLECTION TABLE


For Optimum Life
(15% of free length)
Load (lb)

360.0
348.0
336.0
331.2
327.6
331.2
329.4
324.0
324.0
316.8
576.0
540.0
532.8
529.2
504.0
529.2
510.0
504.0
499.2
504.0
475.2
1128.0
1104.0
1040.4
1029.0
1027.2
999.0
1020.0
993.6
969.6
1008.0
979.2
1431.0
1404.0
1335.6
1320.0
1274.4
1296.0
1274.4
1200.0
1260.0
1281.6

Deflection (in)

0.23
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.90
1.80
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.90
1.20
1.50
1.80
0.30
0.38
0.45
0.53
0.60
0.68
0.75
0.90
1.20
1.50
1.80
0.38
0.45
0.53
0.60
0.68
0.75
0.90
1.20
1.50
1.80

For Long Life


(17% of free length)
Load (lb)

408.0
394.4
380.8
375.4
371.3
375.4
373.3
367.2
367.2
359.0
652.8
612.0
603.8
599.8
571.2
599.8
578.0
571.2
565.8
571.2
538.6
1278.4
1251.2
1179.1
1166.2
1164.2
1132.2
1156.0
1126.1
1098.9
1142.4
1109.8
1621.8
1591.2
1513.7
1496.0
1444.3
1468.8
1444.3
1360.0
1428.0
1452.5

Maximum Operating Def.


(20% of free length)

*Maximum Deflection
(25% of free length)

Deflection (in)

Load (lb)

Deflection (in)

Deflection (in)

0.26
0.34
0.43
0.51
0.60
0.68
0.77
0.85
1.02
2.04
0.34
0.43
0.51
0.60
0.68
0.77
0.85
1.02
1.36
1.70
2.04
0.34
0.43
0.51
0.60
0.68
0.77
0.85
1.02
1.36
1.70
2.04
0.43
0.51
0.60
0.68
0.77
0.85
1.02
1.36
1.70
2.04

480.0
464.0
448.0
441.6
436.8
441.6
439.2
432.0
432.0
422.4
768.0
720.0
710.4
705.6
672.0
705.6
680.0
672.0
665.6
672.0
633.6
1504.0
1472.0
1387.2
1372.0
1369.6
1332.0
1360.0
1324.8
1292.8
1344.0
1305.6
1908.0
1872.0
1780.8
1760.0
1699.2
1728.0
1699.2
1600.0
1680.0
1708.8

0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.20
2.40
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.20
1.60
2.00
2.40
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.20
1.60
2.00
2.40
0.50
0.60
0.70
0.80
0.90
1.00
1.20
1.60
2.00
2.40

0.38
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.50
3.00
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.50
2.00
2.50
3.00
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.50
2.00
2.50
3.00
0.63
0.75
0.88
1.00
1.13
1.25
1.50
2.00
2.50
3.00

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color green is a registered trademark of Barnes Group Inc.

11

MEDIUM DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

9.53

4.76

12.70

7.14

15.88

8.73

19.05

9.53

25.40
31.75
38.10
44.45
50.80
63.50
76.20
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
114.30
139.70
165.10
190.50
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
165.10
190.50
304.80

CATALOG
NUMBER

103-104
103-105
103-106
103-107
103-108
103-110
103-112
103-148
103-204
103-205
103-206
103-207
103-208
103-210
103-212
103-214
103-218
103-222
103-226
103-230
103-248
103-304
103-305
103-306
103-307
103-308
103-310
103-312
103-314
103-316
103-348
103-404
103-405
103-406
103-407
103-408
103-410
103-412
103-414
103-416
103-418
103-420
103-422
103-424
103-426
103-430
103-448

Load at
1 mm
Def.
(N)

10.5
9.5
7.0
6.0
4.9
4.2
3.7
1.1
19.3
14.4
11.9
10.5
9.6
7.9
6.1
5.3
4.4
3.7
2.5
2.1
1.2
28.7
22.4
18.9
16.8
15.4
10.5
9.8
8.4
7.7
2.8
54.6
44.8
35.0
30.8
25.2
21.0
16.8
14.0
12.6
11.2
10.5
9.6
8.8
7.9
6.7
4.2

For Optimum Life


(25% of free length)
Load (N)

67
75
67
66
62
67
70
80
122
114
113
117
122
125
117
117
125
128
101
100
93
182
178
180
187
196
167
187
187
196
214
347
356
334
342
320
334
320
311
320
320
334
336
334
325
317
320

Deflection (mm)

6.4
7.9
9.5
11.1
12.7
15.9
19.1
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
28.6
34.9
41.3
47.6
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
41.3
47.6
76.2

METRIC DIMENSIONS

BLUE

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(35% of free length)
(40% of free length)

*Maximum Deflection
(50% of free length)

Load (N)

Deflection (mm)

Load (N)

Deflection (mm)

93
105
93
93
87
93
98
112
171
160
159
163
171
175
163
163
175
180
142
140
131
255
249
252
262
274
234
262
262
274
299
486
498
467
479
448
467
448
436
448
448
467
471
467
455
444
448

8.9
11.1
13.3
15.6
17.8
22.2
26.7
106.7
8.9
11.1
13.3
15.6
17.8
22.2
26.7
31.1
40.0
48.9
57.8
66.7
106.7
8.9
11.1
13.3
15.6
17.8
22.2
26.7
31.1
35.6
106.7
8.9
11.1
13.3
15.6
17.8
22.2
26.7
31.1
35.6
40.0
44.5
48.9
53.3
57.8
66.7
106.7

107
120
107
106
100
107
112
128
196
182
181
187
196
200
187
187
200
205
162
160
149
292
285
288
299
313
267
299
299
313
342
555
569
534
548
512
534
512
498
512
512
534
538
534
520
507
512

10.2
12.7
15.2
17.8
20.3
25.4
30.5
121.9
10.2
12.7
15.2
17.8
20.3
25.4
30.5
35.6
45.7
55.9
66.0
76.2
121.9
10.2
12.7
15.2
17.8
20.3
25.4
30.5
35.6
40.6
121.9
10.2
12.7
15.2
17.8
20.3
25.4
30.5
35.6
40.6
45.7
50.8
55.9
61.0
66.0
76.2
121.9

Deflection (mm)

12.7
15.9
19.1
22.2
25.4
31.8
38.1
152.4
12.7
15.9
19.1
22.2
25.4
31.8
38.1
44.5
57.2
69.9
82.6
95.3
152.4
12.7
15.9
19.1
22.2
25.4
31.8
38.1
44.5
50.8
152.4
12.7
15.9
19.1
22.2
25.4
31.8
38.1
44.5
50.8
57.2
63.5
69.9
76.2
82.6
95.3
152.4

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color blue is a registered trademark of Barnes Group Inc.
12

MEDIUM DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

25.40

12.70

31.75

15.88

38.10

19.05

50.80

25.40

25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
304.80
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80

CATALOG
NUMBER

103-504
103-505
103-506
103-507
103-508
103-510
103-512
103-514
103-516
103-518
103-520
103-522
103-524
103-528
103-532
103-548
103-606
103-607
103-608
103-610
103-612
103-614
103-616
103-618
103-620
103-622
103-624
103-628
103-632
103-640
103-648
103-708
103-710
103-712
103-714
103-716
103-718
103-720
103-722
103-724
103-728
103-732
103-740
103-748
103-810
103-812
103-814
103-816
103-818
103-820
103-822
103-824
103-828
103-832
103-840
103-848

Load at
1 mm
Def.
(N)

96.3
78.8
61.3
52.5
45.5
35.0
28.9
26.3
21.0
18.2
16.8
15.4
14.0
12.6
10.5
7.0
86.9
74.3
61.6
50.4
42.0
35.0
30.8
28.0
23.8
22.4
21.0
18.2
15.4
12.6
10.5
92.8
78.8
63.0
52.5
47.3
40.3
36.8
32.4
29.8
25.4
22.4
17.5
14.0
175.1
145.3
113.5
105.1
92.8
82.3
68.6
68.3
54.6
49.9
36.4
30.6

For Optimum Life


(25% of free length)
Load (N)

612
626
584
584
578
556
550
584
534
520
534
538
534
560
534
534
827
825
783
801
801
778
783
801
756
783
801
810
783
801
801
1179
1251
1201
1168
1201
1151
1168
1131
1134
1129
1139
1112
1068
2780
2769
2522
2669
2652
2613
2397
2602
2429
2535
2313
2335

Deflection (mm)

6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
76.2
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2

METRIC DIMENSIONS

BLUE

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(35% of free length)
(40% of free length)

*Maximum Deflection
(50% of free length)

Load (N)

856
876
817
817
810
778
771
817
747
729
747
753
747
785
747
747
1158
1155
1096
1121
1121
1090
1096
1121
1059
1096
1121
1133
1096
1121
1121
1650
1751
1681
1635
1681
1611
1635
1584
1588
1580
1594
1557
1495
3892
3876
3531
3736
3713
3658
3356
3643
3400
3550
3238
3269

Deflection (mm)

8.9
11.1
13.3
15.6
17.8
22.2
26.7
31.1
35.6
40.0
44.5
48.9
53.3
62.2
71.1
106.7
13.3
15.6
17.8
22.2
26.7
31.1
35.6
40.0
44.5
48.9
53.3
62.2
71.1
88.9
106.7
17.8
22.2
26.7
31.1
35.6
40.0
44.5
48.9
53.3
62.2
71.1
88.9
106.7
22.2
26.7
31.1
35.6
40.0
44.5
48.9
53.3
62.2
71.1
88.9
106.7

Load (N)

979
1001
934
934
925
890
881
934
854
833
854
861
854
897
854
854
1324
1320
1253
1281
1281
1245
1253
1281
1210
1253
1281
1295
1253
1281
1281
1886
2002
1922
1868
1922
1841
1868
1810
1815
1806
1822
1779
1708
4448
4430
4035
4270
4243
4181
3836
4163
3886
4057
3701
3736

Deflection (mm)

10.2
12.7
15.2
17.8
20.3
25.4
30.5
35.6
40.6
45.7
50.8
55.9
61.0
71.1
81.3
121.9
15.2
17.8
20.3
25.4
30.5
35.6
40.6
45.7
50.8
55.9
61.0
71.1
81.3
101.6
121.9
20.3
25.4
30.5
35.6
40.6
45.7
50.8
55.9
61.0
71.1
81.3
101.6
121.9
25.4
30.5
35.6
40.6
45.7
50.8
55.9
61.0
71.1
81.3
101.6
121.9

Deflection (mm)

12.7
15.9
19.1
22.2
25.4
31.8
38.1
44.5
50.8
57.2
63.5
69.9
76.2
88.9
101.6
152.4
19.1
22.2
25.4
31.8
38.1
44.5
50.8
57.2
63.5
69.9
76.2
88.9
101.6
127.0
152.4
25.4
31.8
38.1
44.5
50.8
57.2
63.5
69.9
76.2
88.9
101.6
127.0
152.4
31.8
38.1
44.5
50.8
57.2
63.5
69.9
76.2
88.9
101.6
127.0
152.4

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color blue is a registered trademark of Barnes Group Inc.

13

MEDIUM HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

9.53

4.76

12.70

7.14

15.88

8.73

19.05

9.53

25.40
31.75
38.10
44.45
50.80
63.50
76.20
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
304.80

CATALOG
NUMBER

104-104
104-105
104-106
104-107
104-108
104-110
104-112
104-148
104-204
104-205
104-206
104-207
104-208
104-210
104-212
104-214
104-248
104-304
104-305
104-306
104-307
104-308
104-310
104-312
104-314
104-316
104-348
104-404
104-405
104-406
104-407
104-408
104-410
104-412
104-414
104-416
104-418
104-420
104-422
104-424
104-448

Load at
1 mm
Def.
(N)

15.8
12.8
11.7
10.2
8.8
7.4
5.3
1.6
29.4
22.8
16.6
14.9
13.1
10.5
10.0
7.0
2.1
52.5
37.7
33.3
29.4
25.9
20.1
17.5
14.9
13.3
4.7
87.6
66.5
56.0
50.4
43.4
33.6
25.2
22.4
21.0
19.6
15.8
14.0
13.1
6.3

For Optimum Life


(20% of free length)
Load (N)

80
81
89
90
89
93
80
96
149
145
127
132
133
133
152
125
128
267
239
254
262
263
256
267
265
270
288
445
423
427
448
441
427
384
399
427
448
400
391
400
384

Deflection (mm)

5.1
6.4
7.6
8.9
10.2
12.7
15.2
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
61.0

METRIC DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(25% of free length)
(30% of free length)
Load (N)

100
101
112
113
111
117
100
120
187
181
158
165
167
167
190
156
160
334
299
317
327
329
320
334
331
338
360
556
528
534
560
552
534
480
498
534
560
500
489
500
480

Deflection (mm)

6.4
7.9
9.5
11.1
12.7
15.9
19.1
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
76.2

Load (N)

120
122
134
135
133
140
120
144
224
217
190
198
200
200
228
187
192
400
359
380
392
395
384
400
397
406
432
667
634
641
673
662
641
576
598
641
673
600
587
600
576

Deflection (mm)

7.6
9.5
11.4
13.3
15.2
19.1
22.9
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
91.4

RED

*Maximum Deflection
(37% of free length)
Deflection (mm)

9.4
11.7
14.1
16.4
18.8
23.5
28.2
112.8
9.4
11.7
14.1
16.4
18.8
23.5
28.2
32.9
112.8
9.4
11.7
14.1
16.4
18.8
23.5
28.2
32.9
37.6
112.8
9.4
11.7
14.1
16.4
18.8
23.5
28.2
32.9
37.6
42.3
47.0
51.7
56.4
112.8

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color red is a registered trademark of Barnes Group Inc.

14

MEDIUM HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

25.40

12.70

31.75

15.88

38.10

19.05

50.80

25.40

25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
304.80
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80

CATALOG
NUMBER

Load at
1 mm
Def.
(N)

104-504
104-505
104-506
104-507
104-508
104-510
104-512
104-514
104-516
104-518
104-520
104-522
104-524
104-528
104-532
104-548
104-606
104-607
104-608
104-610
104-612
104-614
104-616
104-618
104-620
104-622
104-624
104-628
104-632
104-640
104-648
104-708
104-710
104-712
104-714
104-716
104-718
104-720
104-722
104-724
104-728
104-732
104-740
104-748
104-810
104-812
104-814
104-816
104-818
104-820
104-822
104-824
104-828
104-832
104-840
104-848

133.1
109.3
86.9
77.1
70.0
54.3
43.8
37.8
32.2
29.8
25.2
22.4
21.0
17.5
15.4
10.9
200.3
176.5
151.3
109.3
89.7
77.1
64.4
56.0
50.8
46.2
43.8
35.0
32.2
25.4
21.7
189.1
149.9
109.3
92.5
84.1
75.7
64.4
60.2
53.2
46.2
38.5
30.8
25.2
207.3
168.1
140.1
116.3
105.1
98.1
88.3
82.7
70.0
61.6
45.5
39.2

For Optimum Life


(20% of free length)
Load (N)

676
694
662
685
712
689
667
673
655
681
641
626
641
623
626
662
1527
1569
1537
1388
1366
1370
1309
1281
1290
1292
1334
1245
1309
1290
1324
1922
1904
1665
1644
1708
1729
1637
1683
1623
1644
1566
1566
1537
2633
2562
2491
2363
2402
2491
2466
2519
2491
2505
2313
2391

Deflection (mm)

5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
61.0
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0

METRIC DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(25% of free length)
(30% of free length)
Load (N)

Deflection (mm)

Load (N)

845
867
827
856
890
862
834
841
818
851
801
783
801
778
783
827
1908
1962
1922
1735
1708
1712
1637
1601
1612
1615
1668
1557
1637
1612
1655
2402
2380
2082
2055
2135
2162
2046
2104
2028
2055
1957
1957
1922
3292
3203
3114
2953
3002
3114
3082
3149
3114
3131
2891
2989

6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
76.2
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2

1014
1041
993
1027
1068
1034
1001
1009
982
1021
961
939
961
934
939
993
2290
2354
2306
2082
2050
2055
1964
1922
1935
1938
2002
1868
1964
1935
1986
2882
2856
2498
2466
2562
2594
2455
2525
2434
2466
2349
2349
2306
3950
3843
3736
3544
3603
3736
3699
3779
3736
3758
3469
3587

Deflection (mm)

7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
91.4
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4

RED

*Maximum Deflection
(37% of free length)
Deflection (mm)

9.4
11.7
14.1
16.4
18.8
23.5
28.2
32.9
37.6
42.3
47.0
51.7
56.4
65.8
75.2
112.8
14.1
16.4
18.8
23.5
28.2
32.9
37.6
42.3
47.0
51.7
56.4
65.8
75.2
94.0
112.8
18.8
23.5
28.2
32.9
37.6
42.3
47.0
51.7
56.4
65.8
75.2
94.0
112.8
23.5
28.2
32.9
37.6
42.3
47.0
51.7
56.4
65.8
75.2
94.0
112.8

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color red is a registered trademark of Barnes Group Inc.

15

HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

9.53

4.76

12.70

7.14

15.88

8.73

19.05

9.53

25.40
31.75
38.10
44.45
50.80
63.50
76.20
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
304.80

CATALOG
NUMBER

105-104
105-105
105-106
105-107
105-108
105-110
105-112
105-148
105-204
105-205
105-206
105-207
105-208
105-210
105-212
105-214
105-248
105-304
105-305
105-306
105-307
105-308
105-310
105-312
105-314
105-316
105-348
105-404
105-405
105-406
105-407
105-408
105-410
105-412
105-414
105-416
105-418
105-420
105-422
105-424
105-448

Load at
1 mm
Def.
(N)

19.3
17.2
14.0
14.7
12.6
9.6
7.4
2.1
41.3
32.6
27.1
24.2
19.3
14.7
13.0
10.5
2.8
74.3
51.8
47.6
42.0
36.4
29.8
25.2
21.4
18.9
5.3
189.1
154.1
114.9
105.1
86.9
70.0
59.5
49.0
43.8
38.5
34.1
29.8
28.0
14.0

METRIC DIMENSIONS

For Optimum Life


(15% of free length)

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(20% of free length)
(25% of free length)

Load (N)

Deflection (mm)

Load (N)

Deflection (mm)

Load (N)

Deflection (mm)

73
82
80
98
96
92
84
96
157
155
155
161
147
140
148
140
128
283
247
272
280
278
284
288
285
288
240
721
734
657
701
662
667
681
654
667
661
651
624
641
641

3.8
4.8
5.7
6.7
7.6
9.5
11.4
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
15.2
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
45.7

98
109
107
131
128
122
112
128
210
207
207
215
196
187
197
187
171
377
329
363
374
370
378
384
380
384
320
961
979
875
934
882
890
907
872
890
881
867
832
854
854

5.1
6.4
7.6
8.9
10.2
12.7
15.2
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
61.0

122
136
133
163
160
153
140
160
262
259
259
269
245
234
247
234
214
471
411
454
467
463
473
480
475
480
400
1201
1223
1094
1168
1103
1112
1134
1090
1112
1101
1084
1040
1068
1068

6.4
7.9
9.5
11.1
12.7
15.9
19.1
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
76.2

GOLD
*Maximum Deflection
(30% of free length)
Deflection (mm)

7.6
9.5
11.4
13.3
15.2
19.1
22.9
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
91.4
7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
91.4

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color gold is a registered trademark of Barnes Group Inc.

16

HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

25.40

12.70

31.75

15.88

38.10

19.05

50.80

25.40

Free
Length
(mm)

CATALOG
NUMBER

Load at
1 mm
Def.
(N)

105-504
105-505
105-506
105-507
105-508
105-510
105-512
105-514
105-516
105-518
105-520
105-522
105-524
105-528
105-532
105-548
105-606
105-607
105-608
105-610
105-612
105-614
105-616
105-618
105-620
105-622
105-624
105-628
105-632
105-640
105-648
105-708
105-710
105-712
105-714
105-716
105-718
105-720
105-722
105-724
105-728
105-732
105-740
105-748
105-810
105-812
105-814
105-816
105-818
105-820
105-822
105-824
105-828
105-832
105-840
105-848

364.2
299.8
207.3
182.1
157.6
119.1
95.3
79.9
70.0
61.6
54.6
50.4
44.8
39.2
33.6
21.0
371.3
318.0
262.0
205.9
166.7
131.7
116.3
102.3
92.8
82.7
74.3
64.4
57.4
44.8
36.4
333.4
271.4
227.7
186.3
159.7
137.3
124.7
112.1
102.3
86.9
75.7
60.2
50.4
455.3
350.2
297.7
262.7
210.1
192.6
175.1
164.6
143.6
127.8
96.3
73.5

25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
304.80
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
177.80
203.20
254.00
304.80

METRIC DIMENSIONS

For Optimum Life


(15% of free length)

LOAD DEFLECTION TABLE


For Long Life
Maximum Operating Def.
(20% of free length)
(25% of free length)

Load (N)

Deflection (mm)

Load (N)

Deflection (mm)

Load (N)

1388
1428
1185
1214
1201
1134
1089
1065
1068
1057
1041
1057
1025
1046
1025
961
2122
2120
1996
1962
1906
1756
1772
1753
1768
1732
1697
1719
1751
1708
1665
2541
2585
2602
2485
2434
2354
2375
2349
2338
2317
2306
2295
2306
4337
4003
3970
4003
3603
3670
3670
3763
3830
3896
3670
3363

3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
26.7
30.5
45.7
5.7
6.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
26.7
30.5
38.1
45.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
26.7
30.5
38.1
45.7
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
26.7
30.5
38.1
45.7

1850
1904
1580
1619
1601
1512
1452
1420
1423
1409
1388
1409
1366
1395
1366
1281
2829
2827
2662
2615
2541
2341
2363
2338
2357
2309
2263
2292
2334
2277
2220
3388
3447
3469
3313
3245
3139
3167
3131
3117
3089
3074
3060
3074
5782
5338
5293
5338
4804
4893
4893
5017
5106
5195
4893
4484

5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
61.0
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
35.6
40.6
50.8
61.0

2313
2380
1975
2024
2002
1890
1815
1775
1779
1761
1735
1761
1708
1744
1708
1601
3536
3534
3327
3269
3176
2927
2953
2922
2947
2887
2829
2865
2918
2847
2776
4234
4309
4337
4141
4057
3923
3959
3914
3896
3861
3843
3825
3843
7228
6672
6616
6672
6005
6116
6116
6272
6383
6494
6116
5604

Deflection (mm)

6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
76.2
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
44.5
50.8
63.5
76.2

GOLD
*Maximum Deflection
(30% of free length)
Deflection (mm)

7.6
9.5
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
91.4
11.4
13.3
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4
15.2
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4
19.1
22.9
26.7
30.5
34.3
38.1
41.9
45.7
53.3
61.0
76.2
91.4

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color gold is a registered trademark of Barnes Group Inc.

17

EXTRA HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

Free
Length
(mm)

9.53

4.76

12.70

7.14

15.88

8.73

19.05

9.53

25.40
31.75
38.10
44.45
50.80
63.50
76.20
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
304.80
25.40
31.75
38.10
44.45
50.80
63.50
76.20
88.90
101.60
114.30
127.00
139.70
152.40
304.80

CATALOG
NUMBER

106-104
106-105
106-106
106-107
106-108
106-110
106-112
106-148
106-204
106-205
106-206
106-207
106-208
106-210
106-212
106-214
106-248
106-304
106-305
106-306
106-307
106-308
106-310
106-312
106-314
106-316
106-348
106-404
106-405
106-406
106-407
106-408
106-410
106-412
106-414
106-416
106-418
106-420
106-422
106-424
106-448

Load at
1 mm
Def.
(N)

38.5
28.0
21.9
20.1
15.8
12.3
11.4
2.6
56.0
42.0
35.0
29.8
24.5
20.1
15.8
14.0
4.4
110.3
82.3
66.5
56.0
50.8
38.5
33.3
28.0
23.6
7.9
245.2
192.6
155.9
131.3
119.1
87.6
70.9
60.4
52.5
46.4
41.2
37.7
34.1
16.6

For Optimum Life


(15% of free length)
Load (N)

147
133
125
134
120
117
130
120
214
200
200
198
187
192
180
187
200
420
392
380
374
387
367
380
374
360
360
934
917
891
876
907
834
811
806
801
796
784
789
781
761

METRIC DIMENSIONS
LOAD DEFLECTION TABLE
For Long Life
Maximum Operating Def.
(17% of free length)
(20% of free length)

GREEN
*Maximum Deflection
(25% of free length)

Deflection (mm)

Load (N)

Deflection (mm)

Load (N)

Deflection (mm)

Deflection (mm)

3.8
4.8
5.7
6.7
7.6
9.5
11.4
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
15.2
45.7
3.8
4.8
5.7
6.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
21.0
22.9
45.7

166
151
142
152
136
132
147
136
242
227
227
225
212
217
204
212
227
476
444
431
423
439
416
431
423
408
408
1059
1040
1009
992
1028
945
919
913
907
902
888
894
885
862

4.3
5.4
6.5
7.6
8.6
10.8
13.0
51.8
4.3
5.4
6.5
7.6
8.6
10.8
13.0
15.1
51.8
4.3
5.4
6.5
7.6
8.6
10.8
13.0
15.1
17.3
51.8
4.3
5.4
6.5
7.6
8.6
10.8
13.0
15.1
17.3
19.4
21.6
23.7
25.9
51.8

196
178
167
179
160
156
173
160
285
267
267
265
249
256
240
249
267
560
523
507
498
516
489
507
498
480
480
1245
1223
1188
1168
1210
1112
1081
1074
1068
1061
1045
1052
1041
1014

5.1
6.4
7.6
8.9
10.2
12.7
15.2
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
61.0
5.1
6.4
7.6
8.9
10.2
12.7
15.2
17.8
20.3
22.9
25.4
27.9
30.5
61.0

6.4
7.9
9.5
11.1
12.7
15.9
19.1
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
76.2
6.4
7.9
9.5
11.1
12.7
15.9
19.1
22.2
25.4
28.6
31.8
34.9
38.1
76.2

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color green is a registered trademark of Barnes Group Inc.

18

EXTRA HEAVY DUTY DIE SPRINGS

Raymond
Hole
Dia.
(mm)

Rod
Dia.
(mm)

25.40

12.70

31.75

15.88

38.10

19.05

50.80

25.40

Free
Length
(mm)

CATALOG
NUMBER

Load at
1 mm
Def.
(N)

106-506
106-508
106-510
106-512
106-514
106-516
106-518
106-520
106-524
106-548
106-608
106-610
106-612
106-614
106-616
106-618
106-620
106-624
106-632
106-640
106-648
106-708
106-710
106-712
106-714
106-716
106-718
106-720
106-724
106-732
106-740
106-748
106-810
106-812
106-814
106-816
106-818
106-820
106-824
106-832
106-840
106-848

280.2
203.1
156.9
128.9
109.3
96.7
85.5
75.7
63.0
30.8
336.2
252.2
207.3
176.5
147.1
137.3
119.1
98.1
72.8
58.8
46.2
658.4
515.5
404.9
343.2
299.8
259.2
238.2
193.3
141.5
117.7
95.3
668.3
546.4
445.5
385.3
330.6
302.6
248.0
175.1
147.1
124.7

38.10
50.80
63.50
76.20
88.90
101.60
114.30
127.00
152.40
304.80
50.80
63.50
76.20
88.90
101.60
114.30
127.00
152.40
203.20
254.00
304.80
50.80
63.50
76.20
88.90
101.60
114.30
127.00
152.40
203.20
254.00
304.80
63.50
76.20
88.90
101.60
114.30
127.00
152.40
203.20
254.00
304.80

METRIC DIMENSIONS

GREEN

LOAD DEFLECTION TABLE


For Optimum Life
(15% of free length)
Load (N)

1601
1548
1495
1473
1457
1473
1465
1441
1441
1409
2562
2402
2370
2354
2242
2354
2268
2242
2220
2242
2114
5017
4911
4628
4577
4569
4444
4537
4420
4313
4484
4355
6365
6245
5941
5871
5669
5765
5669
5338
5604
5701

For Long Life


(17% of free length)

Deflection (mm)

Load (N)

5.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
22.9
45.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
22.9
30.5
38.1
45.7
7.6
9.5
11.4
13.3
15.2
17.1
19.1
22.9
30.5
38.1
45.7
9.5
11.4
13.3
15.2
17.1
19.1
22.9
30.5
38.1
45.7

1815
1754
1694
1670
1651
1670
1661
1633
1633
1597
2904
2722
2686
2668
2541
2668
2571
2541
2517
2541
2396
5686
5565
5245
5187
5178
5036
5142
5009
4888
5081
4936
7214
7078
6733
6654
6424
6533
6424
6049
6352
6461

Deflection (mm)

6.5
8.6
10.8
13.0
15.1
17.3
19.4
21.6
25.9
51.8
8.6
10.8
13.0
15.1
17.3
19.4
21.6
25.9
34.5
43.2
51.8
8.6
10.8
13.0
15.1
17.3
19.4
21.6
25.9
34.5
43.2
51.8
10.8
13.0
15.1
17.3
19.4
21.6
25.9
34.5
43.2
51.8

Maximum Operating Def.


(20% of free length)

*Maximum Deflection
(25% of free length)

Load (N)

Deflection (mm)

Deflection (mm)

2135
2064
1993
1964
1943
1964
1954
1922
1922
1879
3416
3203
3160
3139
2989
3139
3025
2989
2961
2989
2818
6690
6547
6170
6103
6092
5925
6049
5893
5750
5978
5807
8487
8327
7921
7828
7558
7686
7558
7117
7473
7601

7.6
10.2
12.7
15.2
17.8
20.3
22.9
25.4
30.5
61.0
10.2
12.7
15.2
17.8
20.3
22.9
25.4
30.5
40.6
50.8
61.0
10.2
12.7
15.2
17.8
20.3
22.9
25.4
30.5
40.6
50.8
61.0
12.7
15.2
17.8
20.3
22.9
25.4
30.5
40.6
50.8
61.0

9.5
12.7
5.9
19.1
22.2
25.4
28.6
31.8
38.1
76.2
12.7
15.9
19.1
22.2
25.4
28.6
31.8
38.1
50.8
63.5
76.2
12.7
15.9
19.1
22.2
25.4
28.6
31.8
38.1
50.8
63.5
76.2
15.9
19.1
22.2
25.4
28.6
31.8
38.1
50.8
63.5
76.2

*Deflection values shown represent compressed lengths near solid and are for design information only.
The color green is a registered trademark of Barnes Group Inc.

19

Square Wire Die Springs

20

New
Part
Number

Old
Part
Number

108-000-001
108-001-100
108-001-200
108-001-000
108-004-000
108-002-000
108-005-000
108-010-000
108-003-000
108-006-000
108-011-000
108-016-000
108-007-000
108-012-000
108-017-000
108-008-000
108-013-000
108-018-000
108-023-000
108-009-000
108-014-000
108-019-000
108-024-000
108-015-000
108-020-000
108-025-000
108-021-000
108-026-000
108-022-000
108-027-000
108-031-000
108-028-000
108-032-000
108-029-000
108-033-000
108-030-000
108-034-000
108-035-000

SR-0
SR-1A
SR-1B
SR-1
SR-4
SR-2
SR-5
SR-10
SR-3
SR-6
SR-11
SR-16
SR-7
SR-12
SR-17
SR-8
SR-13
SR-18
SR-23
SR-9
SR-14
SR-19
SR-24
SR-15
SR-20
SR-25
SR-21
SR-26
SR-22
SR-27
SR-31
SR-28
SR-32
SR-29
SR-33
SR-30
SR-34
SR-35

Plain End Springs - 12" Length


Hole
Size
(in)

Rod
Size
(in)

3/8
7/16
1/2
9/16
9/16
11/16
11/16
11/16
13/16
13/16
13/16
13/16
15/16
15/16
15/16
1 1/16
1 1/16
1 1/16
1 1/16
1 3/16
1 3/16
1 3/16
1 3/16
1 5/16
1 5/16
1 5/16
1 7/16
1 7/16
1 9/16
1 9/16
1 9/16
1 13/16
1 13/16
2 1/16
2 1/16
2 5/16
2 5/16
2 9/16

3/16
1/4
1/4
5/16
1/4
7/16
3/8
5/16
9/16
1/2
7/16
3/8
5/8
9/16
1/2
3/4
11/16
5/8
7/16
7/8
13/16
3/4
9/16
15/16
7/8
11/16
1
13/16
1 1/8
15/16
13/16
1 3/16
1 1/16
1 7/16
1 5/16
1 11/16
1 9/16
1 13/16

Square Wire
Size
(in)
0.063
0.063
0.094
0.094
0.125
0.094
0.125
0.156
0.094
0.125
0.156
0.188
0.125
0.156
0.188
0.125
0.156
0.188
0.250
0.125
0.156
0.188
0.250
0.156
0.188
0.250
0.188
0.250
0.188
0.250
0.312
0.250
0.312
0.250
0.312
0.250
0.312
0.312

Space
Between Coils
(in)

Unit
Pack

0.047
0.079
0.079
0.094
0.063
0.125
0.094
0.063
0.125
0.109
0.109
0.094
0.125
0.109
0.094
0.188
0.172
0.156
0.109
0.250
0.188
0.188
0.125
0.250
0.188
0.156
0.312
0.172
0.312
0.203
0.188
0.344
0.250
0.438
0.297
0.531
0.406
0.438

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6

Raymond Round Wire Die Springs are optimally engineered to ensure maximum fatigue life when using proper
die spring application techniques.
For maximum operating life always pre-load the springs and prevent exceeding the maximum recommended deflection.

Product Characterictics
Material:
Spring Rate:
Load @ Max. Def.:
Free Length:
Hole Dia.:
Rod Dia.:

Music Wire ASTM-A228 or AMS-5112 or Chrome Silicon ASTM-A401


Spring Rate is reference only and can be calculated from the table shown below.
Defined as the load at maximum deflection and is held to +/- 10%.
The overall length of the spring in a free state condition.
Each spring is manufactured to fit into the indicated hole size and is actually less than the
hole diameter.
Each spring is manufactured to fit over the indicated rod size and is actually greater than
the rod diameter.

Hole

Rod

Round Wire Die Springs

Raymond
KEY CHARACTERISTICS

Hole Dia.
(in.)

Rod Dia.
(in.)

Free
Length
(in.)

3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8

3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
9/32
9/32
9/32
9/32
9/32
9/32
9/32
9/32
9/32
11/32
11/32
11/32
11/32
11/32
11/32
11/32
11/32
11/32
11/32

1.00
1.25
1.50
1.75
2.00
2.50
3.00
12.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
12.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
12.00

LIGHT LOAD (GREEN)


Load @
Max.
Max.
Deflection Deflection
(in.)
(lbs.)
0.40
0.50
0.60
0.70
0.80
1.00
1.20
4.80
0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
4.80
0.40
0.50
0.60
0.70
0.80
1.00
1.20
1.40
1.60
4.80

10.08
9.80
9.54
9.45
9.52
9.30
9.12
8.64
19.52
18.55
18.24
18.48
17.36
16.80
17.16
17.08
16.32
40.80
38.50
36.00
35.00
34.64
33.80
32.76
32.34
32.16
30.72

HEAVY LOAD (RED)

MEDIUM LOAD (BLUE)

Part No.

Max.
Deflection
(in.)

Load @
Max.
Deflection
(lbs.)

Part No.

903-104
903-105
903-106
903-107
903-108
903-110
903-112
903-148
903-204
903-205
903-206
903-207
903-208
903-210
903-212
903-214
903-248
903-304
903-305
903-306
903-307
903-308
903-310
903-312
903-314
903-316
903-348

0.37
0.46
0.56
0.65
0.74
0.93
1.11
4.44
0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
4.44
0.37
0.46
0.56
0.65
0.74
0.93
1.11
1.30
1.48
4.44

25.90
24.98
24.59
24.15
23.83
23.59
23.31
22.64
45.88
44.40
43.85
42.74
42.18
41.26
40.63
41.57
39.07
67.34
63.36
61.61
59.57
58.46
56.43
55.50
55.17
55.20
52.84

904-104
904-105
904-106
904-107
904-108
904-110
904-112
904-148
904-204
904-205
904-206
904-207
904-208
904-210
904-212
904-214
904-248
904-304
904-305
904-306
904-307
904-308
904-310
904-312
904-314
904-316
904-348

Load @
Max.
Max.
Deflection Deflection
(in.)
(lbs.)
0.30
0.38
0.45
0.53
0.60
0.75
0.90
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
3.60
0.30
0.38
0.45
0.53
0.60
0.75
0.90
1.05
1.20
3.60

35.40
34.50
33.30
32.55
33.00
32.85
32.31
31.32
64.20
61.88
60.30
58.80
59.40
57.75
57.60
56.70
54.72
139.80
131.25
128.25
122.33
121.80
119.25
117.00
117.60
116.40
111.24

Part No.

905-104
905-105
905-106
905-107
905-108
905-110
905-112
905-148
905-204
905-205
905-206
905-207
905-208
905-210
905-212
905-214
905-248
905-304
905-305
905-306
905-307
905-308
905-310
905-312
905-314
905-316
905-348

PACKAGING
Standard
Box
Quantity
200
200
100
100
100
100
100
50
100
100
100
100
100
50
50
50
50
100
100
50
50
50
50
50
50
50
50

21

Compression Spring Assortment Kit: No. 111-840 & 111-845 Plain End Springs - 10" Length
Part
Number

Hole
Size
(in)

107-010
107-011
107-020
107-021
107-030
107-031
107-032
107-033
107-040
107-041
107-042
107-043
107-044
107-045
107-046
107-050
107-051
107-052
107-053
107-054
107-055
107-060
107-061
107-062
107-063
107-064
107-065
107-066
107-070
107-071
107-072
107-073
107-074
107-075
107-080
107-081
107-082
107-083
107-084
107-085
107-086

3/32
3/32
1/8
1/8
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
3/8
3/8
3/8
3/8
3/8
3/8
3/8
7/16
7/16
7/16
7/16
7/16
7/16
1/2
1/2
1/2
1/2
1/2
1/2
1/2

Wire
Diameter
(in)
0.010
0.014
0.012
0.016
0.014
0.018
0.026
0.035
0.018
0.022
0.026
0.031
0.035
0.041
0.047
0.022
0.031
0.037
0.041
0.047
0.055
0.031
0.035
0.043
0.047
0.055
0.062
0.075
0.035
0.047
0.055
0.062
0.075
0.085
0.035
0.047
0.055
0.062
0.075
0.091
0.115

Spring
Rate
(lb/in)

Approx.
Solid Height
(in)

Unit
Pack

0.11
0.48
0.09
0.35
0.09
0.24
1.34
3.30
0.14
0.26
0.67
1.37
1.73
5.40
9.17
0.15
0.57
1.27
2.70
5.45
10.27
0.32
0.58
2.06
2.52
7.29
11.29
30.57
0.54
1.81
4.12
6.45
18.18
30.19
0.26
1.06
2.25
6.77
14.35
30.81
87.36

2.80
3.99
3.00
4.00
2.17
2.52
3.43
6.65
1.71
2.53
2.55
3.10
4.73
3.69
4.70
2.24
3.41
4.07
3.28
3.53
4.40
3.41
3.50
3.01
4.00
3.30
4.03
5.25
2.45
3.29
3.30
4.03
4.13
5.10
3.15
3.53
3.85
2.48
3.38
4.55
6.33

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

111-840 or R-40 Assortment consists of 1 of each spring listed above


111-845 or R-45 Assortment consists of 2 of each spring listed above
22

Compression & Extension Spring Assortment

No. 020-811-440

Part
Number

Free
Length
(in)

Type

Outside
Diameter
(in)

Wire
Diameter
(in)

Spring
Rate
(lb/in)

Approximate Load
@ Ref. Extension
(in)

Assortment
Quantity

Unit
Pack

020-042
020-040
020-039
020-037
020-034
020-095
020-035
020-032
020-033
020-019
020-020
020-024
020-023
020-022
020-026
020-028
020-025
020-018
020-027
020-014
020-013
020-012
020-017
020-015
020-029
020-016
020-009
020-010
020-011
020-030
020-007
020-031
020-008
020-005
020-006
020-004
020-003
020-002
020-001

1
1 1/8
1 1/8
1 7/16
1 5/8
2
2 1/16
2 19/32
2 21/32
3 1/4
4
4
4 1/16
4 1/2
5
5 1/4
5 1/4
5 11/32
5 3/8
5 1/2
5 1/2
5 5/8
5 3/4
5 3/4
6
6 1/8
6 7/16
6 1/2
6 5/8
8
8 1/8
8 1/2
9 1/16
10
10
10
10
10
10

Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.
Ext.

0.188
0.234
0.300
0.344
0.500
0.718
0.156
0.750
0.750
0.375
0.250
0.719
0.734
0.484
0.312
0.438
0.531
0.250
0.344
0.375
0.562
0.547
0.250
0.297
0.875
0.266
0.438
0.328
0.156
1.062
0.344
1.000
0.172
0.359
0.375
0.500
0.625
0.812
0.875

0.014
0.020
0.040 Brass
0.048
0.080
0.107
0.020 Brass
0.105
0.080
0.041
0.028
0.105
0.063
0.063
0.041
0.063
0.062
0.041
0.048
0.054
0.080
0.080
0.028
0.048
0.120
0.035
0.048
0.035
0.026
0.135
0.048
0.105
0.029
0.054
0.047
0.062
0.072
0.072
0.092

0.19
0.75
5.25
15.00
74.93
90.86
0.50
46.00
10.30
1.90
0.81
30.78
1.73
5.23
1.91
6.50
5.00
4.30
2.60
4.00
10.50
10.00
0.59
4.40
18.50
1.10
1.10
0.58
1.18
13.48
1.60
3.96
1.00
2.30
1.32
2.09
2.10
0.75
2.50

0.2 lbs. @ 1.50


0.6 lbs. @ 1.63
2.0 lbs. @ 1.20
10.0 lbs. @ 1.81
23.0 lbs. @ 1.88
51.0 lbs. @ 2.50
8.5 lbs. @ 2.81
29.5 lbs. @ 2.97
12.5 lbs. @ 3.66
5.2 lbs. @ 5.25
1.9 lbs. @ 6.00
36.5 lbs. @ 5.00
4.3 lbs. @ 6.03
14.0 lbs. @ 6.50
3.1 lbs. @ 6.50
16.0 lbs. @ 7.25
8.5 lbs. @ 6.25
8.0 lbs. @ 5.84
6.2 lbs. @ 7.38
10.0 lbs. @ 7.50
24.5 lbs. @ 7.00
24.0 lbs. @ 7.63
1.6 lbs. @ 7.75
9.3 lbs. @ 7.75
26.5 lbs. @ 7.00
4.0 lbs. @ 8.13
4.2 lbs. @ 8.44
2.2 lbs. @ 8.50
2.2 lbs. @ 8.63
38.0 lbs. @ 10.00
6.3 lbs. @ 10.13
16.8 lbs. @ 10.25
3.5 lbs. @ 10.13
6.2 lbs. @ 13.00
5.5 lbs. @ 13.00
10.2 lbs. @ 12.00
8.8 lbs. @ 13.00
5.6 lbs. @ 12.00
11.5 lbs. @ 13.00

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
12
12
12
12
6
12
6
12
12
12
12
6
6
6

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
12
12
12
12
6
12
3
12
12
12
12
6
3
3

23

Compression & Extension Spring Assortment (continued)

24

No. 020-811-440

Part
Number

Type

Outside
Diameter
(in)

Free
Length
(in)

Wire
Diameter
(in)

Spring
Rate
(lb/in)

Solid
Height
(in)

Assortment
Quantity

Unit
Pack

020-077
020-078
020-074
020-073
020-086
020-076
020-085
020-075
020-087
020-084
020-057
020-060
020-058
020-059
020-070
020-080
020-079
020-081
020-093
020-065
020-088
020-063
020-092
020-069
020-094
020-083
020-082
020-090
020-091
020-071
020-062
020-066
020-089
020-072
020-068
020-064
020-061
020-067
020-056
020-055
020-054
020-048
020-052
020-050
020-053
020-051
020-049
020-047

Comp
Conical
Comp
Comp
Comp
Comp
Comp
Comp
Conical
Comp
Conical
Comp
Conical
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Barrel
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp
Comp

0.172
0.281 x 0.156
0.078
0.078
0.375
0.109
0.312
0.109
0.531 x 0.281
0.188
0.656 x 0.938
0.500
0.625 x 0.750
0.531
0.844
0.281
0.281
0.312
0.438
0.875
0.375
0.938
0.500
0.590
0.375
0.312
0.312
0.469
0.500
0.438
1.015
0.859
0.438
0.750
0.625
0.875
0.531 x 1.031 x 0.85
0.688
0.176
0.250
0.312
0.875
0.375
0.625
0.359
0.516
0.734
0.875

0.22
0.50
0.53
0.56
0.78
0.81
0.88
0.91
0.91
0.94
0.94
0.97
1.00
1.03
1.10
1.25
1.31
1.97
2.00
2.00
2.03
2.03
2.06
2.19
2.21
2.44
2.44
2.50
2.50
2.56
2.56
2.59
2.63
2.63
2.84
3.06
3.50
4.02
10.00
10.00
10.00
10.00
11.50
11.50
12.00
12.00
12.00
12.00

0.012
0.013
0.012
0.011
0.042 Brass
0.018
0.025 Ph. Brz.
0.018
0.072
0.012
0.058 Ph. Brz.
0.072 Ph. Brz.
0.080 Brass
0.105
0.080 Brass
0.040
0.040
0.022
0.054
0.120
0.048
0.080
0.048
0.040
0.063
0.028
0.032
0.053
0.063
0.041
0.120
0.135
0.048
0.106
0.080
0.092
0.051
0.105
0.014
0.022
0.022
0.080
0.047
0.054
0.048
0.063
0.080
0.105

1.15
0.68
5.67
3.90
7.40
12.00
2.60
9.30
56.00
0.32
5.08
52.00
33.45
436.00
21.50
18.00
21.05
0.65
15.40
110.00
11.00
16.00
5.60
3.55
42.00
1.00
1.30
12.00
18.00
2.60
56.00
154.00
7.20
75.00
30.00
21.50
1.83
58.00
0.15
0.26
0.19
3.20
2.71
1.22
2.20
2.80
3.80
8.00

0.12
0.12
0.26
0.23
0.38
0.34
0.20
0.41
0.52
0.24
0.36
0.61
0.44
0.95
0.36
0.64
0.54
0.53
0.97
0.96
1.00
0.64
0.81
0.38
1.15
0.67
0.77
0.92
1.00
1.12
1.15
1.49
0.95
1.17
1.08
1.10
0.72
1.95
2.25
2.49
2.27
3.00
4.24
3.56
5.27
5.44
4.88
5.17

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
6
12
12
12
12
6
6

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
3
12
6
12
12
3
3

Compression Spring Assortment Kit No. 111-850


Part
Number

Hole
Size*
(in)

Wire
Diameter
(in)

107-509-000
107-509-100
107-509-200
107-509-300
107-510-000
107-510-100
107-510-200
107-510-300
107-511-000
107-511-100
107-511-200
107-511-300
107-512-000
107-512-100
107-512-200
107-512-300
107-512-400
107-513-000
107-513-100
107-514-000
107-514-100
107-515-000
107-516-000

1/2
1/2
9/16
9/16
5/8
11/16
11/16
11/16
13/16
13/16
7/8
15/16
1 1 /8
15/16
1
1 1/16
1 1/8
1 1/16
1 3/16
1 3/16
1 3/8
1 5/8
1 7/8

0.041
0.054
0.062
0.072
0.054
0.062
0.072
0.068
0.062
0.080
0.098
0.125
0.125
0.080
0.098
0.125
0.135
0.085
0.125
0.090
0.148
0.148
0.148

Spring
Rate
(lb/in)

Plain End Springs - 18" Length


Approx. Solid
Height
(in)

Assortment
Quantity

Unit
Pack

0.60
1.98
1.84
5.10
1.31
1.82
3.03
2.24
1.30
3.50
7.79
15.00
7.57
2.52
5.69
12.73
10.78
2.06
9.00
2.45
12.73
8.60
4.44

3.32
3.89
6.45
5.18
2.92
3.35
4.25
4.28
2.79
3.60
4.02
6.25
6.25
3.60
3.53
4.50
7.29
3.49
4.50
2.88
4.74
4.00
4.74

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Wire
Size
(in)

Spring
Rate
(lb/in)

Approx. Load
@ Ref. Extension
(in)

Unit
Pack

40 lb @ 5.0"
26.5 lb @ 7.0"
38 lb @ 10.0"
48 lb @ 13.0"
66 lb @ 15.0"
74 lb @ 18.0"
100 lb @ 21.0"

6
6
6
6
6
6
6

12
12
12
12
12
12
12
12
12
12
12
12
6
12
6
6
6
6
6
6
6
6
6

*Hole Size refers to the diameter of the hole that the spring will fit into.

Heavy Duty Extension Springs


Part
Number

Free
Length
(in)

Outside
Diameter
(in)

020-099
020-029
020-030
020-100
020-101
020-102
020-103

3 7/8
6
8
10
12
14
16

11/16
7/8
1 1/16
1 1/8
1 1/4
1 3/8
1 9/16

0.105
0.120
0.135
0.148
0.162
0.177
0.207

32.8
18.5
13.5
14.0
12.6
13.9
16.5

25

Compression Springs
Part
Number

Free
Length
(in)

107-100-000
107-101-000
107-102-000
107-103-000
107-104-000
107-105-000
107-106-000
107-107-000
107-108-000
107-109-000
107-110-000
107-111-000
107-112-000
107-113-000
107-114-000
107-115-000
107-116-000
107-117-000

1
1 1/2
2
2 1/2
3
1
1 1/2
2
2 1/2
3
3 1/2
1
1 1/2
2
2 1/2
3
3 1/2
4

Ends Squared and Ground


Hole
Diameter
(in)

Wire
Size
(in)

3/8

0.042

1/2

0.062

5/8

0.072

Spring
Rate
(lb/in)

Approx. Solid
Height
(in)

Unit
Pack

1.44
1.65
1.84
1.03
1.21
0.49
0.69
0.92
1.05
1.24
1.50
0.42
0.59
0.81
0.92
1.07
1.28
1.60

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

Approx. Load
@ Ref. Extension
(in)

Assortment
Quantity

Unit
Pack

10 lbs @ 1.81"
14 lbs @ 6.50"
16 lbs @ 7.25"
8 lbs @ 5.84"
6.2 lbs @ 7.38"
10 lbs @ 7.50"
24 lbs @ 7.62"
1.6 lbs @ 7.75"
9.3 lbs @ 7.75"
4.2 lbs @ 8.44"
2.2 lbs @ 8.62"
2.2 lbs @ 8.62"
6.3 lbs @ 10.12"
3.5 lbs @ 10.13"
6.2 lbs @ 13.00"

2
2
2
2
2
2
2
5
2
2
4
2
2
2
2

20.0
14.0
12.0
8.0
6.0
58.0
42.0
32.0
25.0
24.0
18.0
57.0
34.0
32.0
26.0
20.0
18.0
16.0

Extension Spring Assortment No. 020-835


Part
Number
020-037
020-022
020-028
020-018
020-027
020-014
020-012
020-017
020-015
020-009
020-010
020-011
020-007
020-008
020-005

26

Free
Length
(in)

Outside
Diameter
(in)

1 7/16
4 1/2
5 1/4
5 11/32
5 3/8
5 1/2
5 5/8
5 3/4
5 3/4
6 7/16
6 1/2
6 5/8
8 1/8
9 1/16
10

11/32
31/64
7/16
1/4
11/32
3/8
35/64
1/4
19/64
7/16
21/64
5/32
11/32
11/64
23/64

Wire
Diameter
(in)
0.048
0.063
0.063
0.041
0.048
0.054
0.080
0.028
0.048
0.048
0.035
0.026
0.048
0.029
0.054

Spring
Rate
(lb/in)
15.00
5.23
6.50
4.30
2.60
4.00
10.00
0.59
4.40
1.10
0.58
1.18
1.60
1.00
2.30

12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

Problems and Answers

Problems & Answers


Most problems that arise in the use of die
springs usually result from improper
application... failure to take advantage of
and protect the features engineered into the
spring.

Spring Failure
Raymond die springs are produced under
such careful controls that manufacturing
problems have virtually been eliminated. Die
spring failure is usually due to either poor
spring design and manufacture or incorrect
application of the spring. The most
common problem source is the use of die
springs too close to, or beyond, the springs
physical limitations. The solution, of course,
lies with the designers and users careful
selection of springs for each application.
Other solutions to common spring
problems are as follows:

Spring Guidance
Raymond die springs are manufactured
with ends squared and ground so that they
stand on their own base and compress
evenly under load. There is a positive
relationship between the springs outside
diameter and total length which determines
whether or not a spring will buckle under
load.
Curve For Finding Critical Buckling Conditions
0.75

Ratio: Deflection / Free Length

0.7
0.65
0.6

Figure A provides information as to whether


a specific spring with squared, ground ends
is subject to buckling. The curve indicates
that buckling may occur to a squared-andground spring, both ends of which are
compressed against parallel plates, if the
values fall above and to the right of the
curve.

Deflection

Holes and Rods

Spring Alteration

Holes or pockets provided in the die for


springs must be the specified size listed on
pages 4 to 19. Springs increase in diameter
as they are compressed. If the hole is
undersized, a wearing or binding action will
produce early spring failure.
Holes also must have flat bottoms with
square corners. This will allow the spring to
work on a flat surface and provide uniform
stress on the coils when the spring is
compressed.
Working a spring over a rod also provides
good protection against buckling. Care
should be taken to be sure the rod is
smooth. If the rod is shorter than the spring,
it should have a tapered nose so that there
is no danger of the spring coils coming in
contact with a sharp edge.

Alignment
Care should be taken to make certain that
whatever device is used to contain or guide
the spring is properly aligned on both sides
of the die. Holes or rods that do not match
can cause problems that create spring
failure and damage to the tool.

Deflection beyond the manufacturers


recommendation can cause early spring
failure. Check the press or die travel to be
sure of the actual deflection to which the
spring will be subjected. If it is beyond a
safe limit, changes should be made without
delay.

Each Raymond die spring is carefully


engineered to perform within specific areas
of work. Altering the spring such as
reducing its length or number of coils,
grinding the inside or outside diameter, or
placing restrictions on the movement of the
coils can cause early spring failure. Trying
to alter a spring by grinding down its ends
can change the temper of the material and
negatively affect spring performance.
Altering springs from their manufactured
state almost invariably leads to problems
and failure. Dont gamble an expensive die
for the small amount saved on a cheap
alteration.

Corrosion
Frequently, spring failure can be traced to
corrosive elements. Reduction of material
or pitting of the spring will reduce its useful
life. Be alert to conditions that may effect
the springs surface such as rust, lubricants,
soaps, chemicals, etc. Clean, protected
springs give the best job performance.

0.55

Temperature

0.5
0.45
0.4
0.35
0.3
0.25
0.2
0.15
0.1
0.05
2

10

11

FIG. A

Ratio: Free Length / Mean Diameter

FIG. A

Generally, if the free length is more than


four times the mean diameter of the spring,
it could have a buckling problem under
compression. This is solved by providing
guidance by a pocket, a rod, or both to
reduce buckling. It is always recommended
to provide guidance for any die spring.

Load Loss vs. Temperature

Heat is a frequently ignored


INITIAL
factor in spring failure or load
STRESS
loss. The maximum rated service
P.S.I./bar
temperature for chromium alloy
steel is 475F (250C). Figure B
40,000/2,760
shows the percentage of load50,000/3,450
loss due to heat and stress
60,000/4,400
combinations. Thought should
70,000/4,830
be given to the heat generated
80,000/5,515
by the working die which can
90,000/6,205
be significant in many
100,000/6,895
applications. Heat absorbed
110,000/7,585
by the tool can be transferred
120,000/8,275
to the springs resulting in a loss
FIG.
B B
FIG.
of load and premature spring
failure.

CARBON STEEL
Approximate Percent
Loss of Load
Degrees F/C

CHROMIUM ALLOY
Approximate Percent
Loss of Load
Degrees F/C

250/121 350/177 400/204

250/121 350/177 450/232

2.0
2.0
2.5

3.5
4.0
4.5

4.5
5.0
5.5

1.0
1.0
1.0

2.0
2.0
2.0

5.0
5.0
5.5

3.0
3.0
4.0

5.5
6.0
8.0

6.5
8.0
9.0

1.0
1.5
1.5

2.5
2.5
3.0

6.0
6.0
7.0

4.5
7.0
9.5

9.5
11.5
13.0

10.5
14.0
17.5

2.0
2.0
3.5

4.0
5.0
8.0

8.0
10.0
13.0

27

Raymond Nitrogen Gas Springs

High Force
Long Life
High Cycle Rate

High initial force


Low force increase through stroke
Pressure medium: Nitrogen gas
Range of operating temperature: -25F to 180F
(-32C to 82C)
Maximum piston rod speed:
115 ft/min (35 meters/minute)
Component type mounting fixtures
Manufacturer is ISO 9001 certified
Strict testing and quality control

Raymond offers more than 20 unique models with strokes ranging


from .24" (6mm) to 11.8" (300mm), initial contact forces from 15 lbs.
(66 N ) to 41,000 lbs. (182,000 N), and diameters as small as 0.5"
(12 mm).

If you are designing a new product, or making improvements to an


existing one, a Raymond nitrogen gas spring may be the answer. Call
Associated Spring Raymond technical assistance to discuss new
application ideas. Current applications include valve actuators, shock
absorbing bumpers, mountain bike suspensions, etc.

CALL US AT 1 (800) 228-1156 OR FAX AT


(419) 891-9192 FOR OUR COMPLETE CATALOG
OF SPECIFICATIONS. ASK FOR HEAVY DUTY GAS
SPRING CATALOG, FORM R100.

If your application calls for a custom spring such as a special stroke


length, shorter overall length, smaller diameter, high cycle rates or
other differentiating specifications, call our technical assistance
department and let us customize a spring or spring system for you.

28

Technical Features

Common Die Spring Terminology


OUTER DIAMETER This identifies the outside diameter (OD) of
the die spring.
INNER DIAMETER This is a nominal identification of the inside
diameter (ID) of the die spring.
FREE LENGTH The length of a die spring before it is subject to
any operating force or load.
PRELOAD The distance the free length of the die spring is
reduced by the pressure of assembled tool.
OPERATING TRAVEL The distance which is subtracted from
the spring length after operating force has been applied.
DEFLECTION The amount of change in spring length after
operating force has been applied. The compressed length is
computed by subtracting the initial compression and the operating
travel from the free length.
SOLID HEIGHT The length of a spring when it is compressed
by enough load to bring all the coils into contact with each other.
REMOVE SET The manufacturing process of closing a
compression spring to solid to eliminate load loss in operation.
PERMANENT SET This happens when the elastic limits are
exceeded and the spring does not return to its original length
when the load is released.
ELASTIC LIMIT The maximum compression stress that a die
spring can endure without taking permanent set.
LOAD This is the force built up by compressing the spring.
Load is expressed in terms of total Newtons, which is the load
on the spring per a specific unit of deflection. Load is generated
and stress on the coils increases.
STRESS In a spring, this describes the internal force that resists
deflection under load. This force is equal to, and in the opposite
direction of, the external load. Stress is expressed in Newtons
per square millimeter of sectional area.

CALL OUR SPECIAL ORDER DEPARTMENT FOR DESIGN ASSISTANCE AND QUOTES: 1-800-228-1156

Associated Spring Raymond now offers a proprietary line of mechanical coil spring struts. We designed our struts to meet demanding, maintenance
free applications where conventional gas struts fail. Made of corrosion-resistant stainless steel, and unlike gas and pneumatic models, our struts have
no internal gases or seals to fail.

Whether it is resistance against environmental contamination, high temperature (400F/ 205C+), high humidity, corrosion, or simply life cycle, our
struts offer unmatched performance.
Separate lines are currently offered, with various load and stroke options:
Standard Mechanical Spring Struts: Stainless steel construction, stainless steel springs, and M6 threaded ends
High Load Mechanical Spring Struts: Stainless steel construction, carbon steel springs, and M8 threaded ends.
A full line of Extension, Dampening and Self-Centering models is now available.
All of our models are available with various end configurations.
Associated Spring Raymond will work with your specifications to custom design and produce the mechanical strut that you need, including the brackets
and adjoining hardware.
Typical Applications:
Food Preparation & Processing
Heating, Ventilation & Aeration
Motion Control & Dampening
Clean Room

Typical Industries:
Automotive
Medical, Pharmaceutical & Chemical
Marine
Defense
Nuclear
Agriculture & Construction

For further information, or should you need application design support, please contact us at struts@asraymond.com,
or call us at 1-800-646-6416.
*Patents 6,773,002, 7,066,455 and 7,174,804

For product literature, technical assistance or order information, see your local Raymond distributor . . .
or call us toll-free for the name of the Associated Spring Raymond distributor nearest you.

1705 Indian Wood Circle, Suite 210


Maumee, OH 43537-4046
Toll Free Number: 1-800-458-0867
FAX Number: (419) 891-9192
On the Internet: www.asraymond.com
Form 300
Raymond is a trademark of Barnes Group Inc.
2007 Barnes Group Inc. Printed in U.S.A.

2M/BL/0607

Você também pode gostar