Escolar Documentos
Profissional Documentos
Cultura Documentos
SERVICE MANUAL
S48O413VT-K10
MODELS
13VT-K100/150 13VT-CK10
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS
Page IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................... 2 ELECTRICAL SPECIFICATIONS ............................................................................................................ 6 LOCATION OF USERS CONTROL ........................................................................................................ 7 DISASSEMBLY AND REASSEMBLY ...................................................................................................... 9 INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................. 12 PRECAUTIONS IN REASSEMBLING ................................................................................................... 17 FUNCTION OF MAJOR MECHANICAL PARTS .................................................................................... 18 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS ................................... 20 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY ..................................................................... 40 TROUBLESHOOTING ........................................................................................................................... 42 CHASSIS LAYOUT ................................................................................................................................ 55 BLOCK DIAGRAM OF TV SECTION..................................................................................................... 57 BLOCK DIAGRAM OF VCR SECTION ................................................................................................. 59 OVERALL SCHEMATIC DIAGRAM ....................................................................................................... 69 DESCRIPTION OF SCHEMATIC DIAGRAM ......................................................................................... 71 PRINTED WIRING BOARD ASSEMBLIES ........................................................................................... 83 REPLACEMENT PARTS LIST ............................................................................................................... 89 PACKING OF THE SET ....................................................................................................................... 108
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
13VT-K100/150 13VT-CK10
4A 125V
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)
1. Note that the picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
13VT-K100/150 13VT-CK10
AC VOLTMETER
1.5k ohm 10W
SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have special safety characteristics are identified in this manual; electrical components having such features are identified by " " and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
13VT-K100/150 13VT-CK10
4A 125V
tension.
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE Lors de la rparation de ce systme, supprimer la charge statique en branchant une rsistance de 10 k en srie avec un fil isol (comme une sonde d'essai) entre la mise la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit tre retir de la prise murale.)
1. Il est noter que le tube-image de ce rcepteur est intgralement protg contre l'implosion. 2. Par mesure de scurit, changer le tube-image pour un tube du mme numro de type. 3. Ne pas lever le tube-image par son col. 4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'aprs avoir dcharg totalement la haute tension.
13VT-K100/150 13VT-CK10
AC CA Voltmtre VOLTMETER
1.5k ohm 10W
13VT-K100/150 13VT-CK10
ELECTRICAL SPECIFICATIONS
TV SECTION POWER INPUT: POWER RATING: PICTURE SIZE Width: Height: Depth: CONVERGENCE: SWEEP DEFLECTION: FOCUS: INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: Sound IF Carrier Frequency: Color Sub-Carrier Frequency: AUDIO POWER OUTPUT RATING: SPEAKER Size: Voice Coil Impedance: VHF/UHF ANTENNA INPUT IMPEDANCE: TUNING RANGES VHF-Channels: UHF -Channels: CATV Channels: VCR SECTION Format: Video Recording System: Number of Video Heads: Video Signal Standard: Tape Width: Tape Speed: VHS Standard Rotary Two-Head Helical Scanning 2 pcs. NTSC Color System 12.7mm (1/2inch) (SP)33.35mm/sec (1.31 i.p.s) (LP)16.67mm/sec (0.66 i.p.s) Play back only (EP)11.12 mm/sec (0.44 i.p.s) (SP)160 min (T-160) (EP)480 min (T-160) 0.5 to 2.0 Vp-p, 75 ohm unbalanced -8 dB, 47k ohm unbalanced (0 dB-0.775 Vrms) 5C to 40C (41F to 104F) -20C to 60C (-4F to 140F) 120 V AC 60 Hz 65 W 37.8 cm 38.7 cm 38.2 cm Magnetic Magnetic Hi-Bi-Potential Electrostatic 45.75 MHz 41.25 MHz 42.17 MHz (Nominal) 0.8 W (at 10% Distortion) 5 9 cm (2" 31/2") 16 ohm at 400 Hz 75 ohm unbalanced 2 thru 13 14 thru 69 1,14 thru 125 (EIA, Channel Plan)
Maximum Recording Time: Video Input: Audio Input: Operating Temperature: Storage Temperature:
13VT-K100/150 13VT-CK10
REAR
13VT-K100/150 13VT-CK10
Battery Cover
Remote the battery cover as shown and insert two batteries (size AA) making sure the polarity matches the (+) and () marks inside the battery conpartment.
Pull Up
13VT-K100/150 13VT-CK10
4
K
M
13VT-K100/150 13VT-CK10
5
7
8 9
10
13VT-K100/150 13VT-CK10
GC
PG S PG
S PO
YC K
GC
YC
SP
PO
M
FRONT
11
13VT-K100/150 13VT-CK10
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
12
13VT-K100/150 13VT-CK10 The K-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote transmitter or sets volume and channel change function buttons. Note: There are still a few analog adjustments in the K-series such as 120V adjust, focus, master screen voltage and coils in the picture IF/detector circuit. Follow the steps below whenever service adjustment is required. See table "B" to determine if service adjustments are required.
1. Service mode
Berfore putting unit into the service mode, check, that customer adjustments are in the normal mode, use the reset function in the video adjust menu to ensure customer controls are in their proper (reset) position.
PICTURE: 16
13
13VT-K100/150 13VT-CK10 Table - A ADJUSTMENT ITEM PICTURE TINT COLOR BRIGHT SHARPNESS VERTICAL PHASE H-PHASE RF-AGC V-AMP PIF-VCO R CUT-OFF G CUT -OFF B CUT-OFF G GAIN B GAIN Y-MUTE BALANCE TEXT BOX TEXT PICTURE CCD LEVEL OPTION DATA INTIAL VALUE 16 39 13 32 7 0 20 18 32 40 0 0 0 128 128 0 32 15 20 7 1 ADJUSTMENT COMMENTS
RANGE 0~63 0~77 0~63 0~63 0~13 0~7 0~31 0~63 0-63 0-127 0~255 0~255 0~255 0-255 0-255 0-2 0~63 0-127 0-80 0-10 0-3
*No adjustment is required due to proper setting being made by IC2001 automatically. Table - B PART REPLACED IC2001 IC401 IC2101 CRT X X X ADJUSTMENT NECESSARY UNNECESSARY X Data is stored in IC2101. The adjustment is needed to compensate for characteristics of parts including IC401. Initial setting values are written from IC2001. Adjust for best results. Adjust items related to picture tube only. NOTE
14
13VT-K100/150 13VT-CK10
RF AGC Adjustment
1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "RF-AGC". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears. Note 1: You will have to come out of the service mode to select another channel. Note 2: Setting the data to "0" will produce a black raster.
Picture Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer picture control is set to maximum. 3. Enter the service mode and select service adjustment item "PICTURE". 4. Adjust the data value to achieve normal contrast range.
Tint Adjustment
1. Have unit receive a good local channel. 2. Set customer tint control to center of its range. 3. Enter the service mode and select service adjustment item "TINT". 4. Adjust "TINT" data value to obtain normal flesh tones.
Screen Adjustment
1. Select a good local channel. 2. Enter the service mode and select service adjustment item "COLOR" and set the data value to "0" to set the color level to minimum. You may skip this step, if you selected a B/W picture or monoscope pattern. 3. Select service adjustment item "Y-MUTE" and adjust the data value to "1", this turns off the luminance signal (Y-mute). 4. Select service adjustment item "BRIGHT" and set the value to "32". 5. Adjust the master screen cotrol untill raster darkens to the point where raster is barely seen. 6. Adjust service adjustments item "R-CUT OFF" red "G-CUT OFF" green and "B-CUT OFF" blue to obtain a good grey scale with normal whites at low brightness level. 7. Select service adjustment item "MUTE" and reset data to "0". Select service adjustment item "COLOR" and reset data to obtain normal color level.
Color Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer color control is set to center position . 3. Enter the service mode and select service adjustment item "COLOR". 4. Adjust "COLOR" data value to obtain normal color level.
Brightness Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select service adjustment item "BRIGHT". 4. Adjust "BRIGHT" data value to obtain normal brightness level.
15
13VT-K100/150 13VT-CK10
Vertical-Size adjustment
1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "V-AMP". 3. While observing the top and bottom of the screen, adjust "V-AMP" data value to proper vertical size and linearity.
Figure B.
16
13VT-K100/150 13VT-CK10
PRECAUTIONS IN REASSEMBLING
MOUTING THE CASSETTE CONTROLLER
Initial setting is indispensable before placing the cassette controller in the mechanism. The initial setting is made in two ways;electrical and mechanical.
Electrical setting:
Make a short-circuit between TP7701 and TP7702 and be sure that the mechanism is back to its initial setting position (*1). Now place the cassette controller in position.(This method is used when the mechanism has been already set on its PWB.)
Pulley feed gear
Casecon drive gear
Screwdriver
Large tooth
Mechanical setting:
Turn the loading motors pulley feed gear using a screwdriver and be sure that the mechanism is back to its initial setting position (*1). Now place the cassette controller in position.(This method is applicable for the mechanism alone.)
AC Connector
AL Connector
START SENSOR
17
13VT-K100/150 13VT-CK10
Drum Ass'y 17
21 Take-up Pole Base Ass'y 20 Automatic Head Cleaner Ass'y Drum Motor 19 11 A/C Head Ass'y 22 Fixing Guide
16 Full Erase 1 Head Supply Pole Base Ass'y 2 Sup Main 7 Brake Ass'y Tension 3 Arm Ass'y
10 Pinch Drive Cam 13 Reverse Guide Lever Ass'y 8 Pinch Drive Lever Ass'y Casecon Drive Gear
14
18 Loading Motor
No.
1.
Function
Full erase head assy Erase the old recording on the tape in the recording mode. Tension arm assy Detects the tension of tape while running, and brakes the supply reel disk via the tension band. Sup Main brake lever Brakes the supply reel disk to prevent tape slackening when the unit is stopped in fast forward or rewind mode. Main take-up brake lever Brakes the take-up reel disk to prevent tape slackening when the unit is stopped in fast forward or rewind mode.
No.
13.
Function
Reverse guide lever assy Pulls out the tape and controls the tape drive train height with the upper and lower guides.
3.
16.
Pinch roller lever assy Press-fits the tape to the capstan during tape running.
7.
18.
9.
Loading motor A motive power which drives the mechanism. It transmits the power to the master cam and cassette housing control ass'y.
18
13VT-K100/150 13VT-CK10
Capstan D. D. Motor 3
Drive Belt 4
8 Shifter
5 Clutch Lever
No.
1.
Function
Slow brake Gets in contact with the capstan D.D. motor linking to the master cam in the slow still mode, and brakes it to a certain degree. Capstan D.D. motor A motive power which runs the tape. It transmits the power via the Drive belt.
No.
6.
Function
Limiter pulley assy Transmits the power of the capstan D.D. motor to the reel disk via the drive idler. Shifter Transmits the operation of the master cam to break assy, Ioading gear, tension arm and clutch lever. Take-up loading gear Shifts the take-up pole base and guide roller via the loading gear T, and applies the tape around the drum assembly, as well as transmits the power to the loading gears.
8. 3.
9. 4. Drive belt Transmits the power to run the tape to the Limiter pulley.
19
13VT-K100/150 13VT-CK10
1.
JiGVHT-063
CZ
CM CN These Jigs are used for checking and adjusting the torque of take-up and supply reel disks.
3.
JiGTH0006
AW
4.
Torque Driver
JiGTD1200
CB
When fixing any part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg)
5.
BR BY BS BF
These Jigs are used for checking and adjusting the reel disk height.
6.
There are two gauges used for the tension measurements, 300 g and 2.0kg. This Jig is used with the tension gauge. Rotary transformer clearance adjusting jig. These Jigs are used for loosening or tightening special hexagon type screws. This Jig is used for height adjustment of the reverse guide (for reverse guide height adjustment).
7.
JiGADP003
BK
JiGHW0012 JiGHW0015
AE AE
9.
JiGDRiVER11055
AR
20
13VT-K100/150 13VT-CK10
No.
Jig ltem
Part No.
Code
Configuration
Remarks These tapes are especially used for electrical fine adjustment.
Video Audio 7k 1k 7k Hi-Fi Audio Track 58m 58m 30m
JiGDRiVERH-4 AP
12.
JiGDRiVER-6
BM
13.
JiGRVGH-F18
BU
21
13VT-K100/150 13VT-CK10
Reel belt Tension band assy Loading Motor Idler assy Limiter pulley Supply/take-up Main brake levers NOTE: : Part replacement. : Cleaning : Oil refilling <Specified> Cleaning liquid Industrial ethyl alcohol
* This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found, clean or replace parts.
22
13VT-K100/150 13VT-CK10
Notes: 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. 2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated). 3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum. 4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum. 5. After installing the cassette housing control once perform cassette loading operation.
Figure 1-1.
Reassembly 1. Before installing the cassette housing control, shortcircuit TP7701 and TP7702 provided at the left of the main PWB, prug in the power cord. The casecon drive gear turns and stops when the positioning mark appears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below.
500g
Mechanism chassis
Figure 1-3.
Notes: 1. The weight should not be more than 500g. 2. Take care not to damage the tape when the Cassette is set in the mechanism shassis or taken out of it because the supply/take-up poles are shifted foward the tape loading direction in the EJECT position.
23
13VT-K100/150 13VT-CK10
4. Assemble the Sup main brake ass'y. Notes: 1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere. 2. Do not damage the Sup main brake ass'y. Be careful so that grease does not adhere to the brake surface. Reassembly (Take-up reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft. 3. Check the reel disk height and reassemble the take-up main brake ass'y. Note: 1. Take care so that the Tu main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface. 2. After reassembly, check the video search rewind back tension (see page 27), and check the brake torque (see page 29). Height checking and adjustment Note: 1. Set the master plane with due care so that it does not contact the drum. 2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage.
Figure 1-4. Note: When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed.
Supply reel disk Cassette lock release shaft Take-up reel disk Position pin
Figure 1-6. Figure 1-5. Reassembly (Supply reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Match the phases of reel disk and reel relay gear, and set the new reel disk. 3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y.
Note: Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk.
24
13VT-K100/150 13VT-CK10 Note: Whenever replacing the reel disk, perform the height checking and adjustment.
Master plane Reel disk height adjusting jig Mechanism chassis
A
Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
10 0.2mm
Reel disk
Reel disk
Figure 1-7.
Torque gauge
The gauge is held at its maximum value. (Red mark) Idler ass'y
Figure 1-9.
Idler ass'y
Figure 1-8. Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less that the set value, replace the reel belt.
Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt.
25
13VT-K100/150 13VT-CK10 Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
CCW
500g
Figure 1-10. Checking 1. Make sure that value is within the setting 6.92.5mNm (7025gfcm). 2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting. 3. Set the EP record mode (x3) and make sure that the winding-up torque is within setting. Adjustment If the playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: When the torque cassette is set, put a weight (500g) to prevent rise. Figure 1-11.
Note: Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible. Adjustment 1. If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of fluctuation as setting.
26
13VT-K100/150 13VT-CK10
Figure 1-13. 1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage. 2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction. 3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft. 4. Make sure that the measured value is within setting 0.9 to 11.8 N (900 to 1,200g).
CCW
500g
Figure 1-14. Checking 1. Set a cassette tape, push the REC button to place the unit in the SP record mode. Now check the tension pole position.
27
13VT-K100/150 13VT-CK10 2. Visually check to see if the right edge of the tension pole is within the 1.5 0.25mm from the right edge of the Sup guide shaft. Tension pole adjuster adjusting range
Tension pole adjuster
90
90
Figure 1-18.
Adjust so that the delta mark of tension pole adjuster is within 90 range (left, right).
1.5 0.25mm
Figure 1-16. Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise. At right side from the center line
500g
1.5 0.25mm
Figure 1-17. Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise.
Figure 1-19.
Checking 1. Push the REC button to place the unit in the SP record mode. 2. At this time ascertain that the back tension is within the setting (36.5 to 52gcm) by seeing the indication of torque cassette meter.
28
13VT-K100/150 13VT-CK10 Adjustment 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
A Tension arm B CW Take-up reel disk CCW
Torque gauge
Tension spring
Figure 1-20.
After short-circuiting TP7701 and TP7702 provided at the left on the main PWB, plug in the power cord, then turn on the power. 1. 2. 3. Setting Switch from the FF mode to the STOP mode. Disconnect the power cord. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.
Figure 1-21. Remove the cassette housing control assembly. After short-circuiting TP7701 and TP7702 provided at the left on the main PWB, plug in the power cord, then turn on the power. Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Switch from the FF mode to the STOP mode. 3. Disconnect the power cord. Checking Turn the torque gauge at a rate of about one turn/2 sec in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 8.8 to 23.5mNm (90 to 240gfcm); CCW direction: 3.9 to 9.8mNm (40 to 100gfcm).
Checking 1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 8.8 to 23.5mNm (90 to 240gfcm), CW direction: 4.9 to 11.8 mNm (50 to 120gfcm). 2. Adjustment of the brake torque at the supply side and the take-up side Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque. If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring.
29
13VT-K100/150 13VT-CK10
3. Align the left end of gear of A/C head arm with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head arm. Tentative tightening torque must be 0.15 to 0.20 Nm (1.5 to 2.0kgfcm).
Height screw 3 Tilt screw Azimuth screw 2 Left end of A/C head arm gear Punched line mark on chassis
Figure 1-25.
Height screw Spring 1
Note: 1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken. 2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in Page 32, 33.)
Figure 1-23.
Replacement 1. Solder the removed PWB to the new head assembly. 2. Adjust the height from the A/C head arm (lower surface) to the A/C head plate to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw section and A/C head front section) (See the figure below.)
Solder
New A/C head ass'y A/C head PWB Never touch the head A/C head plate
10.8mm
10.8mm
Figure 1-24.
30
13VT-K100/150 13VT-CK10
Height screw
Cassette tape
Mechanism chassis
13.38mm
(b)
Mechanism chassis
2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER 11055)).
Figure 1-26.
Box driver
1. Set the cassette tape in the unit. 2. Press the PLAY button to put the unit in the playback mode. 3. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below.
A/C head
CCW
Tape 0.3mm
Figure 1-29. 3. Set the tape, and check for tape crease near the reverse guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 1-30.)
A Capstan motor shaft Fixing guide Mechanism chassis Reverse guide
Figure 1-27. Adjustment Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape.
500g
31
13VT-K100/150 13VT-CK10
Notes: 1. Previously set the tracking control in the center position, and adjust the envelope waveform to maximum with X value adjustment nut. Thereby the tape run rough adjustment is facilitated. 2. Especially the outlet side envelope waveform must have higher flatness.
Figure 1-32. 2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the method stated in "Page 30 Replacement 3". 2 Connect the oscilloscope to the audio output (TP6601). 3 Using the alignment tape in which 1 kHz linear audio signal has been recorded, adjust the height screw so as to get max audio output. 4 Using the alignment tape in which 7 kHz linear audio signal has been recorded, adjust the azimuth screw so as to get max audio output.
500g
Weight of 500g
Figure 1-31. 7 Press the tracking button (+), () and change the envelope waveform from max to min and from min to max. At this time make sure that the envelope waveform changes nearly parallel. 8 Unless the envelope waveform changes nearly parallel, adjust the height of supply side and takeup side guide roller so that the envelope waveform changes nearly parallel. (For envelope adjustment procedure refer to Figure 1-35.) 9 Turn the tilt screw to remove the tape crease at the fixing guide flange. Play back the tape and check for tape crease at the fixing guide flange. (1) If there is no tape crease Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears. (2) If there is tape crease Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange.
For X value adjustment Adjust the X value, turning the geartype screwdriver.
Figure 1-33.
32
13VT-K100/150 13VT-CK10 3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switching pulse). 2 Rough adjustment of X value Tentatively fix A/C head arm screws 1 and 2 by the method described in Page 30 "Replacement 3". After shortcircuiting TP7701 and TP7702, plug in the powercord, then turn on the power. And playback the alignment tape (VROBBZGS). As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Figure 1-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: When the A/C head is adjusted, adjust so that the maximum envelop waveform is obtained nearest the position of initial setting made in Page 30.) 3 Press the tracking button (+), () and change the envelope waveform from max to min and from min to max. At this time adjust the height of supply and takePB CHROMA Envelope
CH-1
CH-2
Head switching pulse Figure 1-34. up side guide roller with the adjustment driver (JiGDRiVERH-4) so that the envelope waveform changes nearly parallel. 4 If the tape is lifted or sunk from the helical lead surface, the PB CHROMA envelope waveform appears as shown in Figure 1-35. 5 Press the tracking button (+), () and make sure that the envelope waveform changes nearly parallel. 6 Finally check tape crease near the reverse guide. If tape crease is found, remove it as stated in Page 31 "HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3. When the tape is below the helicallead. Supply side Take-up side
When the tape is above the helical lead. Supply side Take-up side
Adjustment
Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Supply side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the envelope.
Take-up side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the envelope.
Figure 1-35. 4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the method described in Page 30 "Replacement 3". 2 After shortcircuiting TP7701 and TP7702, plug in the powercord, then turn on the power. And playback the alignment tape (VROBBZGS). As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. 3 Move the A/C head with the X value adjustment gear driver by the method shown in Figure 1-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: At this time adjust so as to get the maximum envelope waveform nearest the A/C head position which has been set in case of X value rough adjustment as stated in Page 33, 3- 2.) 4 Tighten finally the screws 1 and 2. Be sure to tighten at first the screw 1 and then the screw 2. Final tightening torque is 0.6Nm (If the screw 2 is tightened first, the X value may deviate.) 5 Adjust the playback switching point (Refer to the electric adjustment method.) 6 Playback the self-picture-recorded tape, and check the flatness of envelope waveform and sound. Note: When the A/C head X value adjustment is performed, be sure to perform at first X value rough adjustment (refer to Page 33, 3-2). 1
2
Figure 1-36.
33
13VT-K100/150 13VT-CK10
Notes: 1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it. 2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.) 3. Be careful not to damage the upper drum or the video head. 4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y. 5. After installation adjust the playback switching point for adjustment of servo circuit.
Reel belt
Figure 1-37.
3 1 FFC 4
2. Remove the three screws 2. Reassembly 1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws. 2. Install the reel belt. Notes: 1. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the movement. 2. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in Page 32 item 2. If crease is found, adjust as stated in Page 31 "HEIGHT ADJUSTMENT OF REVERSE GUIDE".
Upper drum
Figure 1-38.
34
13VT-K100/150 13VT-CK10
[Cares when replacing the drum] 1. Be careful so that the drum earth brush is not lost. 2. Do not touch directly the drum surface. 3. Fit gently the screwdriver to the screws. 4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care. 5. Make sure that the drum surface is free from dust, dirt and foreign substances. 6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment. Playback switching point adjustment X-position adjustment and check 7. After replacing the drum clean the drum.
7 2 1 6
4 3 2 1
Figure 1-39.
Figure 1-40.
35
Align here.
Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly.
Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis. Pinch drive lever ass'y
Figure 1-41-1. 2Insert Pinch Roller/Pinch Double Action Lever Assy. 3Insert Open Lever.
Open lever Pinch Roller Double Action Lever Ass'y Phase Matching Point 2
Figure 1-41-2.
Figure 1-41-3.
36
13VT-K100/150 13VT-CK10
1. Make sure that the loading gear is at the point 1 as shown below. 2. Install, paying attention to 6 insertion points and 3 release points. 3. For the phase matching at the insertion point 1, see the point 2 as shown below. 4. Finally fix the inserts 1 and 4.
Reel pulley
Figure 1-42.
Phase-Matching point 2 Loading gear (T) Round mark Insert point 1 Shaft 1 Half round notch
Sifter
Insert point 3
Insert point 2
Insert point 4
Shaft 1
Insert point 6
Phase-matching point 1
Shaft 1
Release point 3
Figure 1-43.
37
13VT-K100/150 13VT-CK10
Apply grease
No grease Fully turn counterclockwise Face the wide tooth side ward
Figure 1-44-1.
Note: See the figure below for the phase matching between the master cam and the casecon drive gear. 3. Finally fix with the E-ring.
Figure 1-45.
Master cam
Replacement 1. Remove the loading motor, and install the replacement loading motor as shown below.
When installing the master cam, align the casecon drive gear round mark with the half-round notch of master cam.
Figure 1-46. The loading motor pressing-in must be less than 14.7 N (15 gf). Adjust the distance between motor and pulley to 10.2 +0.2 0.2 mm).
Figure 1-44-2.
38
13VT-K100/150 13VT-CK10
MSPRT0381AJFJ
Apply grease
Figure 1-47.
Drive angle
Drive gear R
Frame
Figure 1-48.
39
13VT-K100/150 13VT-CK10
5.5 }0.5H(Iines)
V-sync.
Figure 2-1.
1. Play the alignment tape.(VROATSV.) 2. Press the CH " (TR ) button and the "0" button of remote control at the same time to turn the set into the adjustment mode for head switching point and to set the tracking to center. (See Notes below) "T" is displayed on the TV screen. 3. Press the PLAY button of remote control to make the adjustment of head switching point, then the leading edge of the head switching pulse is automatically set 5.5H (lines) ahead of the vertical sync as shown Figure 2-1 and the adjustment data is memorezed in the E2P-ROM IC. 4. Then press the stop button to stop the tape.
Notes: 1 To make this adjustment, disable the AUTO TRACKING function. The AUTO TRACKING function is disable in the following cases. (In the playback mode only.) a When the CH " (TR ) button and the "0" button of the remote control are pressed at the same time. b When the AC cord is plugged in with making TP7701 and TP7702 short circuited, after the cassette housing control ass'y is removed. (Mechanism operating mode) The AUTO TRACKING function becomes available in the following cases. a When the CH ' (TR) button and the CH" (TR ) button of the remote control are pressed at the same time. b When the AC cord is plugged in with the cassette housing control ass'y put back. 2 Pressing both the CH " (TR ) and the "0" button transmits the test code. When the unit receives this test code in the playback mode, "T" is displayed at the position of CH number on the screen. This function is available to the remote controls RRMCG1330PESA/SB.
40
Figure 2-2.
41
13VT-K100/150 13VT-CK10
ELECTRICAL TROUBLESHOOTING
FLOW CHART NO.1-1 Key-in input for VCR is not received. KEY-IN TROUBLESHOOTING FLOW CHART NO.1-2
Unplug the AC power cord. Replug it a few minutes later. YES YES Check power circuit. Is there short-circuit in the key input? YES NO NO
NO
Are the AT 5V and AT 12V NO lines normal? YES NO Check poor soldering. Are signals received at pin (27) of IC2001 when the key is activated? YES Check IC7701, IC2001 and signal line of serial datas, serial clock and ready (L).
Are the AT 5V and GND lines properly connected with IC7701? YES NO Check/replace X7701 and/or IC7701.
42
NO Check the signal line of sys-con reset all the way up to pin (42) of IC3101. NO Check the power key input to IC2001 and serial datas/clocks between IC2001 and IC7701. NO Check power circuit.
Does the "L" pulse of syscon reset appear at pin (43) of IC7701 after the AC cord is plugged in? YES
Does pin (21) of IC7701 change from "L" to "H" level when the power button is pressed to turn on the power? YES
Check the sensor inputs to IC7701 from mechanism. (CAM switches,start/end sensors,and reel sensors)
NO Does the start sensor cover beceme open when the cassette tape is inserted? Check the start sensor cover. NO
NO
NO Check the start sensor and the way up to pin (2) of IC7701. NO
Check the take up reel sensor and all the way to IC7701.
NO Check pin (12) of IC7701 and all the way up to pin (5) of IC7702. NO
Does the capstan motor start when the EJECT button is pressed? YES Does the take-up reel disk turn when the capstan motor is running? YES Is reel pluse at pin (80) of IC7701 when the take-up reel disk is turning? YES Is "H" level (about 1.8V) at pin (6) of IC7702 when reel pulse is inputted? YES Is about 11V at pin (10) of IC7702? NO
Check between pin (6) of IC7702 and all the way up to pin (11) of IC7701. Check IC7702 and "L" level of pin (5) of it. NO
YES Is the correct voltage at the loading motor terminal? YES Does the loading motor run? YES Replace the cassette cam, gear, etc.
Check between IC7702 and all the way up to the loading motor. NO Replace the loading motor.
43
Check the start sensor and all the way up to IC7701. Check the end sensor and all the way up to IC7701. Check cam switches and all the way up to IC7701.
YES Does the start sensor pin (2) of IC7701 go to "L" level when the cassette tape is inserted? YES Does pin (5) of IC7702 (BA6209) go to "H" level (about 1.8V) when the cassette tape is inserted? YES Does pin (2) of IC7702 go to about11V when the cassette tape is inserted? YES Is the correct voltage at the loading motor terminal when the cassette tape is inserted? YES Check and replace the loading motor.
Does start sensor pulse at pin (2) of IC7701 change from "L" to "H" NO level when the cassette tape is loaded? YES Does end sensor pulse at pin (3) of IC7701 change from "L" to "H" NO level when the cassette tape is loaded?
YES
Do the cam switches A and B operate normally when the cassette tape is loaded?
NO
YES
13VT-K100/150 13VT-CK10
Replace IC7701
SYSTEM CONTROL TROUBLESHOOTING CAPSTAN MOTOR TROUBLESHOOTING The capstan motor fails to run. No power.
13VT-K100/150 13VT-CK10
Is 5V at pin (8) of AC connector? Check IC2001 and IC7701. NO YES Is the voltage more than about 2.6V given to pin (4) of AC connector? YES Is the voltage at pin (3) of AC connector 1.8~2.7V? Check IC7701. Is 8V or 12V at pin (5) of AC connector? Check IC765 (PC9V GEN.) Check/replace the capstan motor. Check Q756 (PC5V GEN.) YES NO YES NO
NO
Check the AT5V line. Check between the MC connector and IC7701, and between the MC connector and pin (75) of IC7701. Check pin (74) of IC7701
Are serial clock pulse and TV NO data pulse applied to pins (67) and (66) of IC7701 from IC2001? YES Are system control data pulse and system control ready pulse NO applied to pins (36) and (35) of IC2001 from IC7701? YES Does power control (H) signal at NO pin (21) of IC7701 change from "L" to"H" level? YES
NO
YES
NO
44
YES Check peripheral circuit for poor soldering of PC9V and PC5V lines.
TAKE-UP REEL PULSE GENERATOR TROUBLESHOOTING FLOW CHART NO.1-7 DRUM MOTOR TROUBLESHOOTING The drum motor fails to run.
Is the voltage more than about 2.6V applied at pin (1) of ME connector. NO YES YES YES Is 12V at pin (4) of ME connector? YES Check/replace the drum motor. NO Check between D7702 and pin (80) of IC7701, between D7703 and pin (79) of IC7701. Is 5V at pin (7) of ME connector? NO
Check between the ME socket and pin (78) of IC7701, and between the ME socket and pin (76) of IC7701. Check the AT 5V line.
about 4.5Vp-p
Insert the cassette, and put the unit in FF or REW mode. NO Are there the take up/supply reel pulses at the collectors of D7702/D7703. NO
45
FLOW CHART NO.1-8 The drum motor runs only for a few seconds. NO See FLOW CHART NO. 1-9. Is drum PG signal at pin (5) of ME connector? YES YES Check pin (18) of IC7701 and signal line of head switching pulse. Is drum PG signal at pin (86) of IC7701? YES IS H.SW. pulse at pin (18) of IC7701? YES Check all the way up to pins (86) and (87) of IC7701. @ @ @ @ YES NO Check or replace IC7701. NO Check between the ME connector and all the way up to pin (86) of IC7701. NO Check the drum motor.
4.2
D-PG
4.4
D-FG
Are the drum PG and drum FG signal inputted to pins (86) and (87) of IC7701, respectively? NO
Are there the drum PG and drum FG Signals at pins (3) and (5) of connector AD? NO Check the harness AD-ME and the drum motor unit.
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
Is there 16MHz oscillation at pins (38) and (39) of IC7701? NO Check X7701, C7705 and C7706. In REC mode YES
In PB mode
Is there the durm PG signal at pin (86) of IC7701? YES YES Is there the head NO switching pulse at pin (18) of IC7701? YES Is there the drum control output at pin (78) of IC7701? NO Replace IC7701. YES Is there the drum control voltage applied to pin (1) of ME connector? YES NO
NO Check the composite sync. signal at pin (14) of IC2201, Q2201 and Q2202.
46
Is pin (76) of IC7701 in high impedance? NO Replace IC7701. Check AT 12V at pin (4) and AT 5V at pin (7) of ME connector. Check and replace the drum motor. YES Check the signal line between pin (7) of AD and pin (76) of IC7701.
Check PG and FG to pins (5) and (3) of the connector ME and the drum motor.
A Are REC and /or PB mode inoperative? YES NO Is there 16MHz oscillation at pins (38) and (39) of IC7701. Check X7701, C7705 and C7706. Check the capstan FG signal line between AM connector and IC7701. NO Does there appear the capstan FG signal at pin (85) of IC7701? YES YES Only REC mode inoperetive.
Does there appear the V-sync. at pin (84) at IC7701? YES Is there REC CTL signal output at pins (92), (91) of IC7701? NO Replace IC7701.
NO
47
YES Is there capstan control signal at pin (77) of IC7701? YES NO Replace IC7701. Is there the capstan control voltage applied to pin (4) of AC connector? NO YES Is pin (75) of IC7701 normal? Replace the FFC AA-MH. YES Check " A " Replace A/C head. Check " B " In case of NO GOOD Replace the capstan motor. NO
YES
Does CTL amplifier circuit of IC7701 (pins (92) to (97)) operate normally? (Does the noise appear at pin (97) when touch R7774 by hand?)
NO
Check the composite sync. signal at pin (14) of IC2201, Q2201 and Q2202, up to pin (84) of IC7701. Replace IC7701.
NO
NO
13VT-K100/150 13VT-CK10
E-E MODE TROUBLESHOOTING No E-E signal. Recording (LUMINANCE) is not possible. Recording is possible but without color.
13VT-K100/150 13VT-CK10
Is there a signal at pin (20) or (16) of IC2201? YES Is there a signal at NO pin (57) of IC2201? YES Check PC 5V lines. YES NO YES Are pins (36) and (35) of IC3301 at 5V? YES Is there a signal at pin (10) of IC3301? YES Check upper and lower drum. NO Replace IC3301. NO Check between pins (8) and (7) of IC2201 and all the way up thrn to pins (52) and (51) of IC7701. Is there a signal at pin (26) of IC3301? NO YES Check parts around pins (30) and (31) of IC2201.
NO Check IC401 and parts around it. Is there a signal at NO Check parts pin (29) of around and pins IC2201? (27), (38), (36) and (29) of IC2201. YES
NO
YES
Is there a signal at NO Check parts pin (10) of around pins (12), IC2201? (43), (45) and (10) of IC2201. YES Is there a signal at NO Check pin (94) of pin (57) of IC2201. IC2201? (VCO control)
Check between pin (47) of IC401 and all the way up thru to pin (20) or (16) of IC2201.
NO
Is the supply voltage of NO 5V feed to pins (4), (21), (48) and (63) of IC2201? I2C
YES
Check between pin (25) of IC2201 and pin (14) of IC402. YES Replace IC2201.
YES Are there the bus data and clock at pins (8) and (7) of IC2201?
Check between pin (57) of IC2001 and all the way up thru pin (26) of IC3301.
48
Is there a signal at pin (30) NO Is the supply voltage of 5V of IC3301? feed to pin (36) of IC3301? Check PC5V line. YES Is there H.SW.P. at pin (1) of IC3301? NO Check H.SW.P. line. Replace IC3301. YES
NO
YES
49
NO Check the I2C bus data and clock at pins (8) and (7) of IC2201. YES Is there a signal at pin (25) of IC2201?
YES
NO Check between pin (30) of IC3301 and all the way up thrn to pin (57) of IC2201.
LUMINANCE
Playback is possible but CHROMINANCE without color. Is there a signal at pin (12) NO Check peripheral circuits of of IC2201? X5502.
YES
NO
Replace IC2201.
YES
Check between pin (25) of IC2201 and all the way up thru pin (14) of IC402.
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
No E-E signal
Is there a signal at pin (87) or (91) of IC2201? Is there "H" level at pin (70) of IC2201? YES NO Is there a signal at pin (81) of IC2201? YES Replace IC2201. After there the I2C bus data and clock signal at pins (8) and (7) of IC201? NO YES Check the I2C bus data and clock signal line.
NO Check circuits around the audio output circuit in tuner (TU51) and parts around the audio inputs jack (J401).
NO
YES Are there the I2C bus data and clock signal at pins (8) and (7) of IC2201? YES Is voltage of pins (86) and (88) of IC2201 normal? NO Check PC 9V line. YES YES Is there a signal (Bias) at pin (6) of T6601? YES Is there a signal (Bias+Audio sig.) at pin (4) of connector AA? YES Check FFC MH-AA and A/C head. NO NO Is there "H" level at pin (72) of IC2201? YES Check A-MUTE (H) Line. (IC2201 pin (72)~ IC7701 pin (50)). Replace IC2201. NO Is there "H" level at pin (2) of T6601?
NO Check between pins (8) and (7) of IC2201 and all the way thru to pins (52) and (51) of IC7701.
NO
YES
Check T6601, Q6603, Q6604 and their peripheral parts. Check the signal line between pin (4) of connector AA and pin (81) of IC2201, and pin (6) of T6601.
50
Is there a signal at pin (74) of IC2201? YES NO Check BIAS CTL (H) line. Is there "L" level at pin (70) of IC2201?
NO
YES Are the FFC MH-AA and the PB AMP's peripheral parts around pins (75)~(78) of IC2201 normal? YES Clean A/C head. NO
51
Readjust azimuth and height. YES Replace A/C head. NO NO Is there "L" level at pin (72) of IC2201? YES Is there a signal at pin (85) of IC2201? YES NO
Replace IC2201.
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
Is AC cord connected?
YES Is 120V AC applied to line between K701 and IC702? NO AC cord broken. Normal Replace the Fuse YES Abnormal Pin (7) of T701 voltage check about: 170V DC at 120V AC The Fuse is again blown out.
Check D701 thru D704, L701, and R701. YES Check IC701 and adjacent parts. Abnormal +B voltage check about: 115.0V (C730 side)
IC701, Check
Does pulse waveform NO exist at line between pin (2) and (3) of IC701? YES IC701, D727 Normal
Normal
TROUBLESHOOTING OF TV SECTION
52
Normal Q601, Q602 and R603
Abnomal
Normal
IC401 (iX2933CE)
C854
Circuit to be checked: 1. TUNER 2. PIF 3. Automatic gain control 4. 9V power source FLOW CHART NO.2-3 NO VERTICAL SCAN Vertical freq check
NO PICTURE, NO SOUND
Does the noise level increase at max, Contrast, Brightness, and Sound Control?
Abnormal
Picture noise decrease but sound level varies greatly. YES Is there a signal at NO pin (53) of IC401. Normal NO IC501 (LA7830) bias check. Pin (22) of IC401 bias check.
CF631 (503kHz)
Abnormal
YES
IC401
Is there a signal at pin NO Check the Q404, (43) of IC401? Q433 and adjacent parts. YES YES YES
Is there Check a signal the at pin NO IC401 (8) of and IC351 adjacent (TDA parts. 7233)? Is there a signal at pin (54) of IC401?
Abnormal
53
Is there a signal NO Check the at pin IC351. (5) of IC351? Check the IC401, and adjacent parts. YES Check the speaker. Abnormal Does the 9V (+B) appear at pin (48) of IC401? Normal Abnormal Check IC401. Check the PC9V line.
Normal
D502, C509, C510 and R511 Check the CRT connector K1~K6 and adjacent parts.
Normal
Check IC2001.
Normal
Abnormal
13VT-K100/150 13VT-CK10
Check IC401.
13VT-K100/150 13VT-CK10
YES NO Does waveform appear at pin (54) of IC401? Is there a signal at pin (55) of IC401? NO YES NO Check IC401 and adjacent parts. Check the TV: TROUBLESHOOTING "NO SOUND". Check the VCR: TROUBLESHOOTING "NO SOUND".
INFRARED R/C TROUBLESHOOTING FLOW CHART NO.2-6 No operation is possible from the infrared remote control.
NO PLAYBACK PICTURE
Is there a signal at pin (39) of IC401? NO Check the VCR: TROUBLESHOOTING "NO PLAYBACK". Does the infrared remote control function? YES Is 5V applied at pin (2) of the remote control receiver? YES Is "L" pulse given out of pin (1) of the receiver and received at pin (10) of IC2001, when the infrared remote control is activated? YES Is fluorescent lighting enough away from the set?
54
YES Is there short-circuit in the key input or IC2001? YES Check IC2001.
NO
NO
NO
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
CHASSIS LAYOUT
H
PWB-B
PWB-D
PWB-C
A
PWB-A
1 2 3 4 5 6 7 8 9 10 11 12
55
56
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
57
58
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
59
60
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
61
62
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
63
64
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
65
66
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
67
68
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
69
70
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
CONDI-
1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. All voltages measured with 1000V B&W or Color signal.
F
1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. MARK= X-RAY RELATED PARTS.
F
DRGANNES MARQUES ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
WAVEFORMS
D D
10 4
115
6 12
71
72
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
73
74
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
75
76
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
77
78
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
DTC124ES
10
11
12
79
80
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
10
11
12
81
82
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
83
84
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
85
86
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
87
88
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. D656 D710 D2001 D2002 D2003 D2060 D2201 D2202 D3103 D3104 D3123 D7701 D7702 D7703 D7704 D7705 D7707 D7710 D7711 D8301 D8302 D8303 D8304 VA701 Part No. RH-EX0631GEZZ RH-DX0131CEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-EX0654GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-PX0252GEZZ RH-PX0252GEZZ RH-PX0253GEZZ RH-PX0253GEZZ RH-PX0270GEZZ VHD1SS119//-1 VHD1A3-F///-1 RH-PX0008PEZZ RH-PX0013PEZZ RH-PX0013PEZZ RH-PX0013PEZZ RH-VX0026CEZZ # J J J J J J J J J J J J J J J J J J J R R R R J Description Zener Diode, 9.1V Diode Diode Diode Diode Diode Diode Diode Diode Zener Diode, 20V Diode Diode Gp1S563 Gp1S563 Gp1S94 Gp1S94 Photodiode Diode Diode Photodiode Photodiode Photodiode Photodiode Varistor Code AA AC AB AB AB AB AB AB AB AB AB AB AF AF AF AF AC AB AA AE AC AC AC AC
PARTS LIST
PARTS REPLACEMENT
H Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP # MARK: SPARE PARTS-DELIVERY SECTION L MARK: X-RAY RELATED PARTS
Ref. No.
Part No.
Description
Code
Ref. No.
Part No.
Description
Code
E
V101
PICTURE TUBE
VB370BVBK1S-S RCiLG0403PEZZ R R R Picture Tube Deflection Yoke Degaussing Coil BZ BB AK
PACKAGED CIRCUITS
X801 X5502 X7701 RCRSB0022PEZZ RCRSB0204GEZZ RCRSB0159GEZZ R J J Crystal Crystal Crystal AG AG AF
DY601 RCiLH0160PEZZ
INTEGRATED CIRCUITS
D
COILS
L51 L53 L201 L202 L203 L211 L301 L302 L303 L321 L401 L402 L403 L404 L615 L701 L2040 L2202 L2203 L2205 L2206 L2207 L2213 L2223 L3101
10
IC351 IC401 IC402 IC501 IC2001 IC2040 IC2101 IC2201 IC3301 IC6601 IC7701 IC7702
VHiTDA7233/-1 RH-iX2933CEZZ VHiM52055FP-1 VHiLA7830//-1 RH-iX3092CEZZ VHiPST994C/-1 VHiBR2401E2-1 VHiNN3472F/-1 VHiAN3363S/-1 VHiBA7755//-1 RH-iX3056CEZZ VHiBA6209//1E
J J J J J J J J J J J J
TDA7233 TA1268N M52055FP LA7830 I.C. PST994C BR24C01AF NN3472FAS AN3363SB BA7755 M37776M5A155GP BA6209-V3
AF AX AH AH AZ AD AF BD AH AD AZ AG
TRANSISTORS
B
DIODES
AC AA AA AA AA AA AA AA AD AM AA
6
Q201 Q301 Q351 Q401 Q402 Q403 Q404 Q433 Q601 Q602 Q2002
1 2 3
VS2SC1906//1E VS2SC2412KQ-1 VS2SC3198-Y-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VS2SC2412KQ-1 VS2SA1037KQ-1 VS2SA1037KQ-1 VS2SC2482//-1 VS2SD2586//1E VS2SC2412KQ-1
4
J J J J J J J J J J J
5
2SC1906 2SC2412K (Q) 2SC3198 (Y) 2SC2412K (Q) 2SA1037K (Q) 2SC2412K (Q) 2SA1037K (Q) 2SA1037K (Q) 2SC2482 2SD2586 2SC2412K (Q)
D51 D52 D401 D402 D451 D455 D501 D502 D651 D652 D653
7
RH-EX0619GEZZ RH-EX0207CEZZ VHD1SS119//-1 RH-EX0603GEZZ RH-EX0616GEZZ VHD1SS119//-1 RH-DX0441CEZZ RH-DX0131CEZZ VHD1SS82///1A VHD1SS119//-1 RH-EX0628GEZZ
8
J J J J J J J J J J J
Zener Diode, 6.2V Zener Diode, 30V Diode Zener Diode, 3.8V Zener Diode, 5.6V Diode Diode Diode Diode Diode Zener Diode, 9.1V
9
AA AA AB AA AA AB AC AC AC AB AC
VP-DF220K0000 RCiLP0123CEZZ VP-XF1R2K0000 RCiLi0618CEZZ VP-XFR56K0000 VP-XF560K0000 VP-XF8R2K0000 RCiLi0617CEZZ VP-XF220K0000 VP-XF560K0000 VP-XF120K0000 VP-XF2R7K0000 VP-XF6R8K0000 VP-XF8R2K0000 RCiLP0270CEZZ RCiLF0040PEZZ RCiLB0015PEZZ VP-DF4R7K0000 VP-XF330K0000 VP-XF101K0000 VP-MK471K0000 VP-MK561K0000 VP-MK470J0000 RCiLP0123CEZZ VP-XF100K0000
11
J J J J J J J J J J J J J J J R R J J J J J J J J
Peaking 22H Coil Peaking 1.2H IF Coil Peaking 0.56H Peaking 56H Peaking 8.2H IF Coil Peaking 22H Peaking 56H Peaking 12H Peaking 2.7H Peaking 6.8H Peaking 8.2H Coil Coil Oscillation Coil Peaking 4.7H Peaking 33H Peaking 100H Peaking 470H Peaking 560H Peaking 47H Coil Peaking 10H
12
AB AC AB AE AB AB AB AD AB AB AB AB AB AB AE AL AF AB AB AB AB AB AB AC AB
89
90
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. C343 C351 C352 C354 C355 C356 C357 C360 C361 C401 C402 C403 C405 C406 C408 C409 C410 C411 C412 C413 C414 C418 C419 C420 C422 C423 C451 C454 C502 C504 C505 C507 C508 C509 C510 C513 C514 C551 C552 C553 C602 C603 C606 C607 C612 C631 C632 C633 C652 C653 C701 C713 C767 C801 C802 C803 Part No. VCCCCY1HH151J VCKYCY1HB272K VCEAEA1CW107M VCEA0A1CW477M VCEA0A1CW226M VCQYTA1HM104K VCKYCY1CF474Z VCKYCY1HF103Z VCEA0A1CW337M VCCCCY1HH271J VCCCCY1HH470J VCCCCY1HH100D VCEA0A1HW105M VCEA0A1HW474M VCEA0A1CW106M VCEA0A1HW105M VCQYTA1HM104K VCEA0A1CW108M VCKYCY1CB104K VCKYCY1HF103Z VCE9EA1HW105M VCKYCY1HF103Z VCEA0A1CW476M VCE9EA1HW105M VCEAKM1CW106M VCEA0A1CW106M VCQYTA2AA563K VCEA0A1CW106M VCEA0A1VW477M VCKYPA2HB561K VCQYTA1HM473K VCQYTA1HM152K VCEA0A1HW107M VCKYPA2HB102K VCEA0A1VW477M VCEA0A1HW225M VCEACA1HC335J VCEACA1HC225J VCEA0A1HW225M VCCCCY1HH391J VCKYPA1HB102K VCKYPA2HB102K VCKYPA1HB472K VCFPPD3CA682H VCFPPJ2EB474J VCEA0A1HW475M VCKYCY1EB103K VCEA0A1CW477M VCEA0A1HW106M VCEA0A1CW106M RC-FZ017SCEZZ RC-EZ0587CEZZ VCEA0A2AW226M VCKYCY1EB223K VCEA0A1HW474M VCCCCY1HH120J # J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 150p 2700p 100 470 22 0.1 0.47 0.01 330 270p 47p 10p 1 0.47 10 1 0.1 1000 0.1 0.01 1 0.01 47 1 10 10 0.056 10 470 560p 0.047 1500p 100 1000p 470 2.2 3.3 2.2 2.2 390p 1000p 1000p 4700p 6800p 0.47 4.7 0.01 470 10 10 0.22 33 22 0.022 0.47 12p 50V Ceramic 50V Ceramic 16V EL. 16V EL. 16V EL. 50V Mylar 16V Ceramic 50V Ceramic 16V EL. 50V Ceramic 50V Ceramic 50V Ceramic 50V EL. 50V EL. 16V EL. 50V EL. 50V Mylar 16V EL. 16V Ceramic 50V Ceramic 50V EL.(N.P) 50V Ceramic 16V EL. 50V EL.(N.P) 16V EL. 16V EL. 100V Mylar 16V EL. 35V EL. 500V Ceramic 50V Mylar 50V Mylar 50V EL. 500V Ceramic 35V EL. 50V EL. 50V EL. 50V EL. 50V EL. 50V Ceramic 50V Ceramic 500V Ceramic 50V Ceramic 1600V M-Poly. 250V M-Poly. 50V EL. 25V Ceramic 16V EL. 50V EL. 16V EL. AC250V Plastic 200V EL. 100V EL. 25V Ceramic 50V EL. 50V Ceramic Code AA AA AC AC AB AC AB AA AC AA AA AA AB AB AB AB AC AD AB AA AC AA AB AC AB AB AB AB AB AA AB AB AB AA AB AB AC AC AB AA AA AA AA AE AF AB AA AC AB AB AD AF AC AA AB AA
TRANSFORMERS
T601 T602
T6601
R R J
AE BC AE
CAPACITORS
(EL. : Electrolytic, M-Poly. : Metalized Polypro Film) C51 VCEA0A1CW476M J 47 16V EL. C52 VCKYCY1HF103Z J 0.01 50V Ceramic C53 VCEA0A1HW105M J 1 50V EL. C54 VCEA0A1HW225M J 2.2 50V EL. C55 VCEA0A1CW477M J 470 16V EL. C57 VCEAKA0JW107M J 100 6.3V EL. C201 VCKYCY1EB103K J 0.01 25V Ceramic C202 VCKYCY1EB103K J 0.01 25V Ceramic C203 VCKYCY1EB103K J 0.01 25V Ceramic C204 VCKYCY1CF104Z J 0.1 16V Ceramic C205 VCEA0A1HW474M J 0.47 50V EL. C206 VCEA0A1CW477M J 470 16V EL. C207 VCKYCY1HF103Z J 0.01 50V Ceramic C208 VCEA0A1HW474M J 0.47 50V EL. C209 VCKYCY1HB102K J 1000p 50V Ceramic C210 VCKYCY1CF104Z J 0.1 16V Ceramic C211 VCCCCY1HH270J J 27p 50V Ceramic C241 VCEA0A1CW477M J 470 16V EL. C301 VCCCCY1HH470J J 47p 50V Ceramic C303 VCKYCY1HB682K J 6800p 50V Ceramic C305 VCKYCY1CB104K J 0.1 16V Ceramic C306 VCCCCY1HH470J J 47p 50V Ceramic C307 VCCCCY1HH101J J 100p 50V Ceramic C308 VCKYCY1EB103K J 0.01 25V Ceramic C309 VCEA0A1CW107M J 100 16V EL. C310 VCKYCY1CB104K J 0.1 16V Ceramic C314 VCKYCY1CB104K J 0.1 16V Ceramic C329 VCKYCY1EB103K J 0.01 25V Ceramic C340 VCKYCY1CB104K J 0.1 16V Ceramic C341 VCE9EA1HW105M J 1 50V EL.(N.P) C342 VCKYCY1HB472K J 4700p 50V Ceramic
AB AA AB AB AC AB AA AA AA AA AB AC AA AB AA AA AA AC AA AA AB AA AA AA AC AB AB AA AB AC AA
91
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. C3104 C3105 C3107 C3108 C3109 C3110 C3111 C3112 C3113 C3114 C3115 C3116 C3117 C3130 C3301 C3302 C3303 C3304 C3311 C3312 C3313 C3314 C3316 C3317 C5501 C5502 C5503 C5505 C5506 C5507 C5508 C5509 C5510 C5511 C5512 C5513 C5514 C5515 C5519 C6601 C6602 C6604 C6605 C6606 C6610 C6611 C6612 C6613 C6614 C6615 C6616 C6617 C6618 C6619 C6630 C6631 Part No. VCKYCY1HB102K VCCCCY1HH221J VCKYCY1HF103Z VCEAKA0JW107M VCKYCY1CB104K VCKYCY1HB222K VCEAKA0JW107M VCKYPA1HF103Z VCCCCY1HH101J VCCCCY1HH150J VCCCCY1HH150J VCCCCY1HH150J VCEAKA1CW106M VCKYCY1HF103Z VCKYCY1HF223Z VCCCCY1HH220J VCKYCY1HF223Z VCCCCY1HH220J VCKYCY1HB471K VCKYCY1HF103Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAKM1CW476M VCKYCY1HB392K VCEAKA1HW225M VCEAKA1HW225M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1CF474Z VCKYCY1CF104Z VCEAKM0JW476M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1EB223K VCKYCY1HF103Z VCKYCY1CF104Z VCKYCY1CF474Z VCKYCY1CB823K VCKYCY1CB104K VCEAKA1CW226M VCKYCY1EB123K VCKYCY1HB182K VCKYCY1HB102K VCKYCY1HF103Z VCKYCY1HF223Z VCKYCY1HF103Z VCEAKA0JW476M VCEAKM1CW226M VCEAKA0JW476M VCKYCY1CF104Z VCKYCY1CF104Z VCEAKA1CW106M VCKYCY1CF104Z VCQPSA2AA562J VCEAKA1CW476M # J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 1000p 220p 0.01 100 0.1 2200p 100 0.01 100p 15p 15p 15p 10 0.01 0.022 22p 0.022 22p 470p 0.01 0.1 0.1 0.1 47 3900p 2.2 2.2 0.01 0.01 0.47 0.1 47 0.01 0.01 0.022 0.01 0.1 0.47 0.082 0.1 22 0.012 1800p 1000p 0.01 0.022 0.01 47 22 47 0.1 0.1 10 0.1 5600p 47 50V 50V 50V 6.3V 16V 50V 6.3V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 50V 50V 50V 50V 50V 16V 16V 6.3V 50V 50V 25V 50V 16V 16V 16V 16V 16V 25V 50V 50V 50V 50V 50V 6.3V 16V 6.3V 16V 16V 16V 16V 100V 16V Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. EL. Ceramic Ceramic EL. Ceramic EL. Code AA AA AA AB AB AA AB AA AA AA AA AA AB AA AB AA AB AA AA AA AA AA AA AB AA AB AB AA AA AB AA AB AA AA AA AA AA AB AH AB AB AA AA AA AA AB AA AB AB AB AA AA AB AA AC AB
92
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # Description Code
RESISTORS
RJ1 RJ2 RJ3 RJ7 RJ8 RJ9 RJ10 RJ11 RJ12 RJ13 RJ14 RJ15 RJ16 RJ17 RJ18 RJ19 RJ21 RJ22 RJ26 RJ27 RJ28 RJ29 RJ31 RJ33 RJ34 RJ36 RJ37 RJ38 RJ39 RJ40 RJ41 RJ42 RJ43 RJ44 RJ45 RJ48 RJ51 RJ54 RJ56 RJ65 RJ69 RJ70 RJ71 RJ72 R54 R55 R56 R57 R201 R202 R203 R204 R205 R206
(M.Ox. : Metal VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL000J J VRN-MD2AL101J J VRN-MD2AL101J J VRN-MD2AL823J J VRN-MD2AL103J J VRN-MD2AL151J J VRN-MD2AL122J J VRN-MD2AL682J J VRN-MD2AL270J J VRN-MD2AL331J J VRD-RA2EE121J J
Oxide.) 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 0 0.1W 100 0.1W 100 0.1W 82k 0.1W 10k 0.1W 150 0.1W 1.2k 0.1W 6.8k 0.1W 27 0.1W 330 0.1W 120 1/4W
Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
93
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. R454 R456 R466 R501 R504 R505 R506 R507 R508 R510 R511 R512 R516 R517 R518 R519 R525 R551 R552 R554 R601 R602 R603 R608 R611 R615 R631 R632 R633 R651 R653 R654 R655 R656 R702 R718 R801 R802 R803 R804 R805 R806 R807 R809 R810 R961 R962 R2002 R2003 R2004 R2005 R2012 R2013 R2028 R2040 R2043 Part No. VRD-RA2EE184J VRN-MD2AL273J VRN-VV3AB1R5J VRN-MD2AL101J VRD-RA2BE471J VRD-RA2BE101J VRD-RA2BE683G VRD-RA2BE104G VRD-RA2BE683J VRN-VV3AB1R0J VRN-GA2EB1R0J VRD-RM2HD561J VRD-RA2BE153G VRD-RA2BE223G VRD-RA2BE154J VRD-RM2HD681J VRN-MD2AL183J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL393J VRN-MD2AL331J VRD-RM2HD392J VRS-KT3LB222J VRD-RA2BE331J VRD-RM2HD220J VRS-VV3AB271J VRN-MD2AL391J VRD-RA2BE272J VRN-MD2AL472J VRD-RM2HD680J VRD-RA2BE822G VRD-RA2BE103G VRN-MD2AL104J VRD-RM2HD123J VRC-UA2HG395K VRN-GA2EB1R0J VRN-MD2AL103J VRN-MD2AL392J VRN-MD2AL272J VRN-MD2AL272J VRN-MD2AL272J VRN-MD2AL333J VRN-MD2AL000J VRN-MD2AL101J VRS-CY1JF000J VRD-RA2BE101J VRD-RA2BE101J VRN-MD2AL332J VRN-MD2AL103J VRN-MD2AL392J VRN-MD2AL562J VRN-MD2AL472J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J # J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 180k 1/4W 27k 0.1W 1.5 1W 100 0.1W 470 1/8W 100 1/8W 68k 1/8W 100k 1/8W 68k 1/8W 1 1W 1 1/4W 560 1/2W 15k 1/8W 22k 1/8W 150k 1/8W 680 1/2W 18k 0.1W 4.7k 0.1W 1k 0.1W 39k 0.1W 330 0.1W 3.9k 1/2W 2.2k 3.0W 330 1/8W 22 1/2W 270 1W 390 0.1W 2.7k 1/8W 4.7k 0.1W 68 1/2W 8.2k 1/8W 10k 1/8W 100k 0.1W 12k 1/2W 3.9 1/2W 1 1/4W 10k 0.1W 3.9k 0.1W 2.7k 0.1W 2.7k 0.1W 2.7k 0.1W 33k 0.1W 0 0.1W 100 0.1W 0 1/16W 100 1/8W 100 1/8W 3.3k 0.1W 10k 0.1W 3.9k 0.1W 5.6k 0.1W 4.7k 0.1W 4.7k 0.1W 1k 0.1W 1k 0.1W 1k 0.1W Code AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA
Carbon Metal Film Metal Film Metal Film Carbon Carbon Carbon Carbon Carbon Metal Film Metal Film Carbon Carbon Carbon Carbon Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Carbon M.Ox. Carbon Carbon M.Ox. Metal Film Carbon Metal Film Carbon Carbon Carbon Metal Film Carbon Solid Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film M.Ox. Carbon Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film
94
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. R3109 R3110 R3111 R3112 R3113 R3117 R3118 R3119 R3120 R3121 R3122 R3123 R3124 R3125 R3127 R3128 R3129 R3130 R3131 R3132 R3133 R3134 R3135 R3136 R3137 R3138 R3139 R3140 R3141 R3142 R3143 R3144 R3145 R3167 R3170 R3173 R3174 R3175 R3176 R3177 R3178 R3179 R3180 R3181 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3308 R3312 R3314 Part No. VRD-RA2BE152J VRN-MD2AL102J VRN-MD2AL103J VRN-MD2AL102J VRN-MD2AL103J VRD-RA2BE102J VRN-MD2AL122J VRS-CY1JF105J VRN-MD2AL222J VRN-MD2AL223J VRN-MD2AL102J VRN-MD2AL223J VRN-MD2AL102J VRN-MD2AL223J VRN-MD2AL334J VRN-MD2AL564J VRN-MD2AL102J VRD-RA2BE223J VRD-RA2BE221J VRN-MD2AL103J VRN-MD2AL221J VRD-RA2BE221J VRN-MD2AL103J VRD-RA2BE102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL103J VRD-RA2BE102J VRN-MD2AL103J VRN-MD2AL681J VRN-MD2AL562J VRN-MD2AL562J VRN-MD2AL562J VRN-MD2AL221J VRN-MD2AL000J VRD-RA2BE4R7J VRN-MD2AL104J VRN-MD2AL104J VRD-RA2BE222J VRN-MD2AL223J VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL223J VRN-MD2AL103J VRN-MD2AL682J VRN-MD2AL472J VRN-MD2AL563J VRN-MD2AL223J VRN-MD2AL103J VRN-MD2AL682J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL682J VRN-MD2AL473J # J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 1.5k 1/8W 1k 0.1W 10k 0.1W 1k 0.1W 10k 0.1W 1k 1/8W 1.2k 0.1W 1M 1/16W 2.2k 0.1W 22k 0.1W 1k 0.1W 22k 0.1W 1k 0.1W 22k 0.1W 330k 0.1W 560k 0.1W 1k 0.1W 22k 1/8W 220 1/8W 10k 0.1W 220 0.1W 220 1/8W 10k 0.1W 1k 1/8W 1k 0.1W 1k 0.1W 10k 0.1W 1k 1/8W 10k 0.1W 680 0.1W 5.6k 0.1W 5.6k 0.1W 5.6k 0.1W 220 0.1W 0 0.1W 4.7 1/8W 100k 0.1W 100k 0.1W 2.2k 1/8W 22k 0.1W 220 0.1W 220 0.1W 220 0.1W 220 0.1W 22k 0.1W 10k 0.1W 6.8k 0.1W 4.7k 0.1W 56k 0.1W 22k 0.1W 10k 0.1W 6.8k 0.1W 4.7k 0.1W 1k 0.1W 6.8k 0.1W 47k 0.1W Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
Carbon Metal Film Metal Film Metal Film Metal Film Carbon Metal Film M.Ox. Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Carbon Metal Film Metal Film Carbon Metal Film Carbon Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film
95
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. R7743 R7744 R7745 R7746 R7747 R7748 R7749 R7750 R7751 R7752 R7753 R7754 R7755 R7756 R7757 R7758 R7759 R7760 R7761 R7762 R7763 R7764 R7765 R7766 R7767 R7770 R7771 R7772 R7773 R7774 R7775 R7776 R7777 R7778 R7779 R7780 R7781 R7782 R7788 R7790 R7791 R7792 R7793 R7794 R7795 R7796 R7797 R7798 R7799 R7800 R7801 R7802 R7803 R7804 R7805 R7806 Part No. VRD-RA2BE103J VRD-RA2BE103J VRD-RA2BE103J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL103J VRN-MD2AL102J VRN-MD2AL393J VRN-MD2AL183J VRN-MD2AL102J VRD-RA2BE223J VRN-MD2AL153J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL274J VRN-MD2AL224J VRN-MD2AL473J VRD-RA2BE472J VRN-MD2AL104J VRD-RA2BE102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL681J VRD-RA2BE332J VRD-RA2BE472J VRD-RA2BE102J VRN-MD2AL154J VRD-RA2BE102J VRN-MD2AL154J VRN-MD2AL103J VRD-RA2BE102J VRN-MD2AL103F VRD-RA2BE102J VRN-MD2AL102J VRN-MD2AL123J VRN-MD2AL103F VRN-MD2AL123J VRD-RA2EE151J VRN-MD2AL332J VRN-MD2AL182J VRD-RA2BE102J VRN-MD2AL104J VRD-RA2BE271J VRN-MD2AL104J VRD-RA2BE271J VRN-MD2AL103J VRD-RA2BE222J VRD-RA2BE103J VRD-RA2BE103J # J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 10k 1/8W 10k 1/8W 10k 1/8W 1k 1/8W 1k 1/8W 1k 1/8W 1k 1/8W 1k 1/8W 1k 1/8W 10k 0.1W 1k 0.1W 39k 0.1W 18k 0.1W 1k 0.1W 22k 1/8W 15k 0.1W 1k 0.1W 1k 0.1W 270k 0.1W 220k 0.1W 47k 0.1W 4.7k 1/8W 100k 0.1W 1k 1/8W 1k 0.1W 1k 0.1W 1k 0.1W 1k 0.1W 1k 0.1W 680 0.1W 3.3k 1/8W 4.7k 1/8W 1k 1/8W 150k 0.1W 1k 1/8W 150k 0.1W 10k 0.1W 1k 1/8W 10k 0.1W 1k 1/8W 1k 0.1W 12k 0.1W 10k 0.1W 12k 0.1W 150 1/4W 3.3k 0.1W 1.8k 0.1W 1k 1/8W 100k 0.1W 270 1/8W 100k 0.1W 270 1/8W 10k 0.1W 2.2k 1/8W 10k 1/8W 10k 1/8W Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Carbon Carbon Metal Film Carbon Metal Film Metal Film Carbon Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Carbon Metal Film Carbon Metal Film Carbon Metal Film Carbon Carbon Carbon
96
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # J J J J J J J J J J J J J R R R R R R R R R R R R R R R R R R J J J J Description Code AB AB AB AB AA AA AD AC AB AC AC AC AL AE AE AB AB AB AB AB AB AB AB AB AB AB AD AD AE AD AD AB AA AA AA
P651 QPLGN0361CEZZ P703 QPLGN0461CEZZ P2201 QPLGN0361CEZZ AE AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA P2401 QPLGN0561CEZZ P3301 QPLGN0352GEZZ P7702 QPLGN0252GEZZ P7706 QPLGZ0883GEZZ SC3301 QSOCN0499REZZ SC6601 QSOCN0695REZZ SC6602 QSOCZ0293GEZZ SC7701 QSOCN0795REZZ SC7702 QSOCZ0292GEZZ RMC3101 RRMCU0222CEZZ RDA501 PRDAR0242PEFW RDA603 PRDAR0219PEFW HM601 LX-GZ3001PEZZ HM602 LX-GZ3001PEZZ HM603 LX-GZ3001PEZZ HM604 LX-GZ3001PEZZ HM605 LX-GZ3001PEZZ HM606 LX-GZ3001PEZZ HM607 LX-GZ3001PEZZ HM608 LX-GZ3002PEZZ HM609 LX-GZ3002PEZZ HM610 LX-GZ3002PEZZ HM611 LX-GZ3002PEZZ PSLDM0251PEFW PSLDM0252PEFW QCNW-2205PEZZ QCNW-5508PEN3 LHLDP1057PEZZ LHLDZ1893AJ00 LX-BZ3100CEFD LX-BZ3100CEFD LX-TZ3004CEFD
Metal Film Metal Film Metal Film Metal Film Carbon Carbon Metal Film Metal Film Metal Film Carbon Carbon Carbon Metal Film Carbon Carbon Carbon Carbon Carbon Carbon
SWITCHES
S2501 S2502 S2503 S2504 S2506 S2507 S2508 S2509 S2510 S2512 S3101 S7701 QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-P0593CEZZ QSW-F0042AJZZ J J J J J J J J J J J J Eject/Stop Play FF REW EZ Play CH-Up CH-Down Vol-Up Vol-Down REC Power REC Tip AB AB AB AB AB AB AB AB AB AB AE AG
Plug 3-pin (TP651-3) Plug 4-pin (YC) Plug 3-pin (TP2201-2, TP6601) Plug 5-pin (TP3101-5) Plug 3-pin (TP3101-3) Plug 2-pin (TP7703, TP7704) Plug 8-pin (AC) Socket 4-pin (AH) Socket 6-pin (AA) Socket 2-pin (AE) Socket 7-pin (AD) Socket 2-pin (AL) Remote Receiver Heat Sink, for IC501 Heat Sink, for Q603 Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Shield Shield Connecting Cord (K703-4) Connecting Cord (OC) Holder Holder Screw Screw Screw
MISCELANEOUS PARTS
F701
FB2001 FB7701 FB7702 FH701 FH702 P350 P401 P402 P404 P602
QFS-B4023CEZZ RBLN-0037CEZZ RBLN-0036CEZZ RBLN-0036CEZZ QFSHD1013CEZZ QFSHD1014CEZZ QPLGN0361CEZZ QPLGZ0840CEZZ QPLGZ1040CEZZ QPLGN0561CEZZ QPLGN0603CEZZ
J J J J J J J J J J J
Fuse 4A Ferrite Bead Ferrite Bead Ferrite Bead Fuse Holder Fuse Holder Plug 3-pin (OR) Plug 8-pin (MA) Plug 10-pin (MB) Plug 5-pin (GC) Plug 6-pin (K)
AC AB AB AB AC AC AB AF AE AB AB
MISCELLANEOUS PARTS
J401 QJAKF0040CEZZ J Jack, Video in, Audio in AF
97
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # Description Code
CAPACITORS
IC756 IC765
J J J
AW AH AG
TRANSISTORS
Q735 Q750 Q751 Q752 Q756 VS2SC3198-Y-1 VSKTA1024-Y-1 VS2SC2229O/1E VS2SC2229O/1E VS2SD471-KL1E J J J J J 2SC3198 (Y) KTA1024 (Y) 2SC2229 (O) 2SC2229 (O) 2SD471 AA AD AD AD AC
DIODES
D701
RH-DX0154CEZZ D702 RH-DX0154CEZZ D703 RH-DX0154CEZZ D704 RH-DX0154CEZZ D705 VHD1SS82///1A D706 VHD10ELS2//-1 D707 VHD1SS82///1A D708 VHSSFOR5D43-1 D709 RH-EX0610GEZZ D711 RH-EX0207CEZZ D722 VHD1SS82///1A D725 RH-DX0469CEZZ D726 RH-DX0469CEZZ D727 RH-DX0466CEZZ D735 RH-EX0617GEZZ D739 RH-EX0602GEZZ D740 VHD1SS82///1A D743 VHD1SS119//-1 D744 VHD1SS119//-1 D751 RH-EX0617GEZZ D775 RH-DX0441CEZZ D776 RH-DX0279CEZZ IC702 RH-FX0034CEZZ IC703 RH-FX0034CEZZ IC775 RH-FX0034CEZZ PR702 RMPTP0026CEZZ
J J J J J J J J J J J J J J J J J J J J J J J J J J
Diode Diode Diode Diode Diode Diode Diode Si.Control Rectifier Zener Diode, 4.7V Zener Diode, 30V Diode Diode Diode Diode Zener Diode, 6.2V Zener Diode, 3.6V Diode Diode Diode Zener Diode, 6.2V Diode Diode PC817 PC817 PC817 Packaged Circuit
AC AC AC AC AC AC AC AC AA AA AC AF AF AE AA AA AC AB AB AA AC AB AE AE AE AF
(EL. : Electrolytic, M-Poly. : Metalized Polypro Film) C702 VCKYPB2HE103P J 0.01 500V Ceramic C703 VCKYPB2HE103P J 0.01 500V Ceramic C705 RC-EZ0514CEZZ J 470 200 EL. C707 RC-KZ0404CEZZ J 0.0033 2kV Ceramic C708 VCCSPA1HL471J J 470p 50V Ceramic C709 VCEA0A1HW107M J 100 50V EL. C710 VCQYTA1HM222J J 2200p 50V Mylar C711 VCFYFA1HA224J J 0.22 50V Mylar C712 RC-KZ0312CEZZ J 0.0047 50V Ceramic C722 VCKYPA1HB102K J 1000p 50V Ceramic C723 VCKYPA1HB102K J 1000p 50V Ceramic C724 VCKYPA1HB102K J 1000p 50V Ceramic C725 VCKYPA1HB102K J 1000p 50V Ceramic C726 VCEAGH1EW228M J 2200 25V EL. C727 VCEAHV1CN108M J 1000 16V EL. C728 RC-KZ0365CEZZ J 0.001 2kV Ceramic C729 RC-KZ0365CEZZ J 0.001 2kV Ceramic C730 RC-EZ0724CEZZ J 100 160V EL. C735 VCCCPA1HH680J J 68p 50V Ceramic C739 VCEA0A1HW104M J 0.1 50V EL. C748 VCEA0A1HW107M J 100 50V EL. C756 VCEA0A1CW476M J 47 16V EL. C757 VCEA0A0JW107M J 100 6.3V EL. C758 VCEA0A1CW226M J 22 16V EL. C759 VCEA0A1AW476M J 47 10V EL. C768 VCEA0A1CW476M J 47 16V EL. C769 VCEA0A1CW476M J 47 16V EL. C775 VCKYPA1HB103K J 0.01 50V Ceramic
AB AB AR AE AA AB AA AB AD AA AA AA AA AE AE AD AD AG AA AB AB AB AB AB AB AB AB AA
RESISTORS
R701 R703
COILS
L725 L726 L727 RCiLP0195CEZZ RCiLP0179CEZZ RCiLP0179CEZZ J J J Coil 68H Coil 47H Coil 47H AD AD AD
TRANSFORMER
T701
RTRNZ0114PEZZ
Transformer
AR
CONTROL
R738 RVR-M4333CEZZ J 6.8K (B) AC
R704 R706 R707 R709 R710 R711 R713 R714 R715 R716 R717 R719 R727 R732 R733 R735 R736 R737 R739 R740 R741
(M.Ox. : Metal Oxide) VRW-KP3HC1R8K J 1.8 5W VRC-UB2HG275K J 2.7M 1/2W VRD-RM2HD154J J 150k 1/2W RR-NZ0048CEZZ J 0.15 2W VRS-SV2HC471J J 470 1/2W VRN-GA2EB1R0J J 1 1/4W VRD-RM2HD180J J 18 1/2W VRD-RA2EE122J J 1.2k 1/4W VRS-SV2HC272J J 2.7k 1/2W VRD-RA2BE102J J 1k 1/8W VRD-RA2BE153J J 15k 1/8W VRD-RA2EE152J J 1.5k 1/4W VRD-RM2HD104J J 100k 1/2W VRW-KQ3HC4R7K J 4.7 5W VRS-VV3DB223J J 22k 2W VRD-RA2EE681J J 680 1/4W VRD-RA2EE152J J 1.5k 1/4W VRD-RA2EE681J J 680 1/4W VRD-RM2HD563J J 56k 1/2W VRD-RA2EE824J J 820k 1/4W VRD-RA2EE681J J 680 1/4W VRD-RM2HD470J J 47 1/2W VRN-RA2BK332F J 3.3k 1/8W
Cement Solid Carbon Metal Film M.Ox. MetalFilm Carbon Carbon M.Ox. Carbon Carbon Carbon Carbon Cement M.Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon Metal Film
AC AF AA AD AA AA AA AA AA AA AA AA AA AE AA AA AA AA AA AA AA AA AA
98
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # Description Code
DIODES
D881 D882 D885 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 J J J Diode Diode Diode AB AB AB
CAPACITORS
C851 C852 C853 C854 C881 C883
MISCELLANEOUS PARTS
RY701 RRLYU0038CEZZ RY725 RRLYU0038CEZZ
(EL. : Electrolytic) VCCCPA1HH151J J 150p VCCCPA1HH151J J 150p VCCCPA1HH151J J 150p RC-KZ0016CEZZ J 0.01 VCEA0A1HW106M J 10 VCEA0A1CW336M J 33
AA AA AA AC AB AB
FB702 FB704 FB725 FB726 FB727 FB731 FB732 P351 P352 P701 P702 P705 SC401 SC402
RDA701 RDA765
J J RBLN-0037CEZZ J RBLN-0036CEZZ J RBLN-0054CEZZ J RBLN-0054CEZZ J RBLN-0057CEZZ J RBLN-0057CEZZ J RBLN-0057CEZZ J QPLGN0261CEZZ J QPLGN0361CEZZ J QPLGN0207CEZZ J QPLGN0304CEZZ J QPLGN0361CEZZ J QSOCZ0840CEZZ J QSOCZ1040CEZZ J PRDAR0209PEFW R PRDAR0232PEFW R R R R R R R R R R R R R J J
HM701 HM702 HM703 HM704 HM705 HM706 HM707 HM708 HM709 HM710
LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ LX-GZ3001PEZZ QCNW-2211PEZZ QCNW-6008PEN3 LX-BZ3049GEFD LX-BZ3100CEFD
Relay 12V Relay 12V Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 2-pin (SP) Plug, 3-pin (OR) Plug, 2-pin (M) Plug, 3-pin (E) Plug, 3-pin (OC) Socket, 8-pin (MA) Socket, 10-pin (MB) Heat Sink, for IC701 Heat Sink, for IC756, IC765 Screw Screw Screw Screw Screw Screw Screw Screw Screw Screw Connecting Cord Connecting Cord (PG) Screw Screw
AM AM AB AB AB AB AC AC AC AB AB AA AB AB AD AD AF AF AB AB AB AB AB AB AB AB AB AB AD AE AA AA
RESISTORS
R851 R852 R853 R857 R858 R859 R860 R861 R865 R866 R867 R868 R869 R873 R874 R881 R882 R883 R884
(M.Ox. : Metal Oxide.) VRD-RA2BE470J J 47 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE121J J 120 1/8W VRS-VV3AB123J J 12k 1W VRD-RM2HD332J J 3.3k 1/2W VRD-RA2BE470J J 47 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE121J J 120 1/8W VRS-VV3AB123J J 12k 1W VRD-RM2HD332J J 3.3k 1/2W VRD-RA2BE470J J 47 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE121J J 120 1/8W VRS-VV3AB123J J 12k 1W VRD-RM2HD332J J 3.3k 1/2W VRD-RA2BE102J J 1k 1/8W VRD-RA2BE221J J 220 1/8W VRD-RA2BE561J J 560 1/8W VRD-RA2BE152J J 1.5k 1/8W
Carbon Carbon Carbon M.Ox. Carbon Carbon Carbon Carbon M.Ox. Carbon Carbon Carbon Carbon M.Ox. Carbon Carbon Carbon Carbon Carbon
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
MISCELLANEOUS PARTS
P851 QPLGN0561CEZZ P852 QPLGN0461CEZZ SC851 QSOCV0842CEZZ QCNW-5025PEN4 QCNW-5030PEN5 J J J R R Plug, 5-pin (GC) Plug, 4-pin (YC) CRT Socket Connecting Cord (YC) Connecting Cord (GC) AB AB AH AE AE
99
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. 55 56 57 58 59 60 61 62 63 65 66 Part No. QCNW-0272AJZZ QPWBF5469AJZZ QSOCN0605REN1 RHEDT0036AJZZ RHEDU0088GEZZ RMOTM1078GEZZ RMOTN2055GEZZ RMOTP1135GEZZ DDRMW0028TEX1 QBRSK0041GEZZ XBPSD26P05J00 # V V V V J J J J V J V Description FFC for A/C Head A/C Head PWB Socket, 6 pin Full Erase Head A/C Head Assy Loading Motor Capstan Motor Drum Drive Motor Upper and lower drum Assy Drum Earth Brush Drum Drive Motor Mounting Screw (SW2.6P+5S) Drum Base PWB(LDG Motor) Socket(LDG Motor) Azimuth Spring Height Adjusting spring Code AF AE AB AM AV AK BA AX BP AD AA
MECHANISM CHASSIS
1 2 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 36 37 38 39 40 41 43 44 45 46 47 48 49 50 51 52 53 LBNDK1011AJZZ LBOSZ1007AJZZ LBOSZ1006AJZZ LCHSM0166AJZZ LHLDZ2016AJZZ LPOLM0063GEZZ LPOLM0064GEZZ MLEVF0518AJZZ MLEVF0519AJZZ MLEVF0499AJZZ MLEVF0500GEZZ MLEVF0496AJZZ LANGF9620AJFW MLEVP0271AJZZ MLEVP0272AJZZ MLEVP0301AJZZ MLEVP0275AJZZ MLEVP0292AJZZ MLEVP0290AJZZ MLEVP0293AJZZ MLEVP0294AJZZ MLEVP0295AJZZ CLEVP0287AJZZ MSLiP0010AJZZ MSPRD0175AJFJ MSPRT0402AJFJ MSPRT0403AJFJ MSPRC0213AJFJ MSPRT0416AJFJ NBLTK0067AJ00 NDAiV1078AJ00 NGERH1293AJZZ NGERH1295AJ00 NGERH1294AJZZ NGERH1270AJZZ NGERH1271AJZZ NGERH1272AJZZ NGERH1299AJZZ NGERW1070AJZZ NGERW1066AJZZ NiDR-0018AJZZ NPLYV0162AJZZ NPLYV0163AJZZ NROLP0131GEZZ NSFTP0032AJZZ MSPRC0217AJFJ PREFL1011AJZZ QCNW-0247AJZZ V V V V V J J V V V J V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V J V V V V Tension Band Assy AH Tension Arm boss AD Cassette Stay L AD Main Chassis Assy BA Loading Motor Block AG Supply Pole Base Assy AM Take-Up Pole Base Assy AM Take-Up Loading AF Arm Assy Supply Loading AF Arm Assy Pinch Drive Lever Assy AG Pinch Roller Lever Assy AW Tension Arm Assy AK A/C Head Plate AG Sifter Drive Lever AE Pinch Double Action LeverAD Reverse Guide Lever AssyAL Reverse Drive Lever AD Slow Brake Lever AE Open Lever AD Clutch Lever AE Sup Main Brake Assy AF Take-Up Main Brake AF Assy Auto Head Cleaner Assy AG Sifter AH Reverse Guide Spring 2 AE Loading Double Action AE Spring Pinch Double Action AD Spring Earth Spring AC Tension Spring AD Reel Belt AE Reel Disk AE Loading Connect Gear AD Master Cam AE Casecon Drive Gear AD Take-Up Loading Gear AF Supply Loading Gear AD Pinch Drive Cam AE Reel Relay Gear AE Worm Gear AD Worm Wheel Gear AD Idler Wheel Assy AK Motor Pully AD Limitter Pulley Assy AM Guide Roller AL Tension Pole Adjuster AB Guide Roller Spring AC Light Guide AE FFC for Drum Motor AG
67 68 69 70 71
J V J V V
AL AE AE AC AC
100
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. MECHANISM CHASSIS PARTS
66
Part No.
Description
Code
H
66
62 66
62
G
63 207 207 50
56 202
201 202
16 71
67
49 51 22
218 49 58 51 32 52 2 24 11 214 12 7 19 18 20 31 8
15 33 25
D
35 35
209 210 211 212 213 223
203
29
5 216 41 43
46 43
61 23
9 21
10 39
B
30
30 36 38 17 37 34
40 48 27 219 6 44
45
208 47 60 68
69
101
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # Description Code
102
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. Part No. CHASSETTE HOUSING CONTROL PARTS # Description Code
300
301
308
309 313
D
310 317
307
315 316
103
13VT-K100/150 13VT-CK10
Ref. No. Part No. # Description Code Ref. No. 20 21 21 22 23 24 25 26 27 28 30 31 32 33 34 35 36 38 39 40 41 42 43 Part No. PSPAG0004PEZZ TLABM1004PEZZ TLABM1286PEZZ LX-TZ0013PEFD LHLDW1064PEKZ LX-HZ3001PEFD XEBSD30P12000 XHPSD30P06WS0 XTASD40P20000 XTASD40P20000 VB370BVBK1S-S RCiLH0160PEZZ RCiLG0403PEZZ PMAGF3041CEZZ QSW-F0042AJZZ QCNW-5025PEN4 QCNW-5030PEN5 PSLDM0251PEFW LHLDZ1893AJ00 LHLDZ0074PEZZ LHLDW0014PEKZ LHLDK0009PEZZ LHLDK0011PEZZ # R R R R R R J J J J R R R J J R R R R R R R R Description Code AB AC AF AD AC AA AA AA AA AA BZ BB AK AG AG AE AE AD AB AC AB AC AE
Spacer Model Label (13VT-K100/150) Model Label (13VT-CK10) Screw Holder Screw Screw Screw Screw Screw Picture Tube (V101) Deflection Yoke (DY601) Degaussing Coil Magnet Rec Tip Switch Connecting Cord (YC) Connecting Cord (GC) Head Amp. Shield Start/End Sensor Holder Holder Wire Holder AC Cord Holder AC Cord Holder
QACCD3055CESB J QCNW-2206PEZZ R VSP9050PB15WA J PSLDM0250PEFW R PSLDM0248PEFW R PSLDM0249PEFW R LANGT0038PEFW R QEARC1404PEZZ R LCHSM0072PEKZ R MSPRT0001PEFJ R PSPAG0022PE00 R LX-TZ0012PEFD R PSLDM0253PEFW R LHLDW0003PEKZ R LHLDW1047PEZZ R LHLDW1065PEKZ R
104
13VT-K100/150 13VT-CK10
13VT-K100/150 13VT-CK10
21 10 2
32
PWB-B
1-13 1-14
1-11 35 1-4 12 16 36
22 20 1-9 1-2 22 33 31
41
6 17 27
25 40 26
1-7
1-9 22
19
PWB-A
1-8 20 22
D
24
7 25 24 9 26 34
38 39
23 15
PWB-C
14 1-8 5 30 24 26
25
3 24 1-10 1-6 4 28 42 43
1-12 @ @ @ @ @
13 1-1 1-3
1 2 3 4 5 6 7 8
28 11
1-5
8
9
PWB-D
10 11
12
105
106
13VT-K100/150 13VT/CK10
Ref. No. Part No. # Description Code Ref. No. Part No. # Description Code
13VT-K100/150 13VT/CK10
SUPPLIED ACCESORIES
TGAN-0018PEZZ TCAUH0011PEZZ TiNS-6469PEZZ TiNS-6406PEZZ TiNS-6428PEZZ QANTR0018PEZZ QANTR0022PEZZ RUNTK0165CEZZ R R R R R R R J Guarantee Card (13VT-K100/150) Caution Card (13VT-K100/150) Operation Manual (13VT-K100/150) Operation Manual (13VT-CK10) Set-up Guide (13VT-K100/150) Rod Antenna (13VT-K100/150) Rod Antenna (13VT-CK10) Antenna Adaptor (13VT-K100/150) Infrared R/C Unit (13VT-K100/13VT-CK10) Infrared R/C Unit (13VT-K150) AD AB AK AK AC AQ AQ AM AV AV
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC6317PEZZ SPAKC6318PEZZ SPAKC6338PEZZ SSAKA0031PEZZ SPAKP0095PEZZ SPAKX2671PEZZ TLABR7005PEZZ TLABN0001PEZZ TLABK0002PEZZ Packing Case (13VT-K100) Packing Case (13VT-K150) Packing Case (13VT-CK10) Polyethylene Sack Polyethylene Sack Buffer Material UPC Label (13VT-CK10) Serial Number Label Number Card
# Polystyrene Bag
RRMCG1330PESA R RRMCG1330PESB R
FRONT
REAR
# Number Card
107
108
13VT-K100/150 13VT-CK10
Memo
109
13VT-K100/150 13VT-CK10
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
110