Você está na página 1de 9

GAS Y PETROQUIMICA BASICA

GERENCIA DE PROYECTO Y CONSTRUCCIN


SUBGERENCIA DE SERVICIOS TCNICOS

PROYECTO: OBRA:

Q-600-64-03
CONSTRUCCIN DE DOS PLANTAS CRIOGNICAS MODULARES Y TERMINAL DE RECIBO Y DISTRIBUCIN DE GAS LP Y GASOLINAS EN LA ESTACIN 19, AREA DE REYNOSA, TAMPS.

LUGAR:

REYNOSA, TAMAULIPAS

ESP-A-1210
ESPECIFICACION DE PROCESO CONTROLLED VOLUME (METERING) PUMPS

No. CONTROLLED VOLUME (METERING) PUMPS


GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

Rev Rev Rev Rev Rev

0 1

Por Gerencia de Proyecto y Construccin Por Gerencia de Proye cto y Construccin Por Por Por

Fecha Fecha Fecha Fecha Fecha

21 mar-00 01 abr 02

Versin nueva Cambios en alguna pgina Versin reeditada completamente X

Preparada por: Pemex Gas y Petroqumica Bsica Fecha: 21 marzo 2000.

Por Gerencia de Proyecto y Construccin Realiz: ACP Especialista Proceso: Revis: GZC Subgerente de Servicios Tcnicos Vo. Bo. LCS Director de Proyecto

Fecha:

21 - marzo - 2000.

ESP-A-1210.doc

Pgina 2 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No. CONTROLLED VOLUME (METERING) PUMPS


GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02 TABLE OF CONTENTS SECTION PAGE

1.0 2.0 4.0 5.0 6.0 8.0

GENERAL....................................................................................................................... 1 BASIC DESIGN.............................................................................................................. 2 ACCESSORIES............................................................................................................. 3 INSPECTION AND TESTING....................................................................................... 3 PREPARATION FOR SHIPMENT ............................................................................... 4 VENDORS DATA ......................................................................................................... 5

ESP-A-1210.doc

Pgina 3 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No. CONTROLLED VOLUME (METERING) PUMPS


GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

FOREWORD This specification covers the minimum requirements for the design and fabrication for Controlled Volume Pumps used in the petroleum and petrochemical industries. This specification is intended to supplement API Standard 675 First edition, March 1980 which is part of this specification. Paragraph numbers of this specification correspond to those in API 675. Paragraph numbers not found in API 675 are new paragraphs. Paragraphs shall be highlighted as shown below to indicate the type of change from the API Standard: (Addition) (Deleted) (Decision) New paragraph or supplemental requirements/clarifications to an existing paragraph. Paragraph deleted. A decision has been made as required.

(Substitution) Paragraphs supersedes API in its entirety. Substitute the terms "Buyer" and "Seller" for the corresponding terms "Purchaser" and "Vendor" used in API 675.

ESP-A-1210.doc

Pgina 4 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No. CONTROLLED VOLUME (METERING) PUMPS


GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02 1.0 1.1 1.1.3 GENERAL Scope (Addition) Compliance by the Seller with this specification does not relieve him of the responsibility of furnishing pumps and accessories of proper design, mechanically suited to meet operating guarantees at the specified service conditions. Neither does it relieve him of the responsibility of furnishing equipment assembled and prepared for shipment in a professional manner. Alternative Designs (Substitution) Proposed design features having less than two years operating experience in similar service shall be specifically listed, and details provided for the Buyer's review. 1.3 Conflicting Requirements (Addition) Should conflicts exist between this specification and other documents, the following order of precedence shall govern: a. b c. 1.5 1.5.4 This Specification and other Buyer documents API 675, March 1980 Sketches

1.2

Referenced Publications (Addition) The following specifications are referenced and applicable as noted herein and/or in the formal purchase order. See the purchase order for the revision in effect.

ESP-L-7781 ESP-P-6760 ESP-H-2900

Motores de Induccin Instruments Furnished with Mechanical Equipment Noise Limits for Equipment and Piping Systems

ESP-A-1210.doc

Pgina 1 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No.
GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

SECCIN DE DESHIDRATACIN, REGENERACION Y FILTRADO


ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

ESP-A-1170 ESP-A-1160 ESP-H-2910 1.5.5

Spare Parts Lubrication Requirements Export Packing

(Addition) Buyers standard forms shall be completed and included as part of the Sellers proposal in lieu of the forms in Appendix A and B of API-675. S.D.C. E-544 E-527 Supplier Drawing and Data Commitment Specification Sheet, Metering Pumps. Induction Motor Data Sheet

2.0 2.1 2.1.2

BASIC DESIGN General (Addition) Pumps, drivers, and all components shall be suitable for continuous full load duty at a relief valve setting of 20 percent or 25 psi (whichever is greater) above the maximum specified operating discharge pressure. (Addition) Stroking speed shall not exceed 80 percent of Seller published maximum. (Addition) Repetitive accuracy shall not be less than 90 percent between the range of 10 to 100 percent of the specified maximum capacity. (Addition) Seller shall submit lubrication data in accordance with Buyers Specification ESP-A-1160 Lubrication Requirements. (Addition) Noise Equipment trains shall comply with Buyers Specification ESP-H-2900 Noise Limits for Equipment and Piping Systems.

2.1.11 2.1.13 2.13.2 2.15

2.4

Pump Check Valves (Decision) Double ball check valves, on both suction and discharge shall be provided.

ESP-A-1210.doc

Pgina 2 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No.
GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

SECCIN DE DESHIDRATACIN, REGENERACION Y FILTRADO


ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

4.0 4.1.1 4.1.3 4.5

ACCESSORIES (Addition) Minimum motor rating for any pump application shall be 1/4 horsepower. (Addition) Motors shall be in accordance with Buyers Specification ESP-L-7781 Motores de Induccin. Nameplates (Addition) An additional nameplate shall be furnished and permanently attached, and stamped (or embossed) with the following information: Equipment item number Size and type of pump Maximum allowable working pressure Maximum flow at rated speed Strokes/Min. (rated/max) Motor: Power/rpm (max)

5.0 5.2 5.2.1.5

INSPECTION AND TESTING Testing (Addition) Test Water Quality Austenitic stainless cladding or lining shall have controlled test water in order to prevent stress cracking. The following criteria shall be used: 1. Water containing more than 50 ppm chlorides shall not be used for test. 2. Equipment must be drained thoroughly after testing. Where complete drainage is impossible, it is necessary to flush with chloride free water, alcohol, petroleum distillate or suitable flushing solution. Hot air drying is not acceptable in lieu of flushing, but water may be blown out of pockets with air.

ESP-A-1210.doc

Pgina 3 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No.
GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

SECCIN DE DESHIDRATACIN, REGENERACION Y FILTRADO


ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

3. Seller shall submit at test report to verify that the chloride content of the test water is less than or equal to 50 ppm. 5.2.2 Hydrostatic Test (Addition) Certification of hydrostatic test results is required. 5.2.3 5.2.3.4 Performance Tests (Decision) Pump shall be given a non-witnessed mechanical run test prior to shipment. Test results shall be submitted to the Buyer and approval of the test results is required prior to shipment. PREPARATION FOR SHIPMENT Type of Shipment and Storage Assembly and preparation for shipment shall be in accordance with Sellers standards and in accordance with Buyers Specification 449111-100-25, Export Packing. 6.2.6 (Addition) Tagging 1. Each item shall be identified with its Purchase Order Number and Item Number. Tags shall be corrosion resistant metal (not aluminum) and impression stamped with the following: P.O. No. Equipment Item No. 2. Tags shall be attached to each component with stainless steel wire. This tagging is in addition to the equipment nameplate. Equipment shipped in fully enclosed containers shall also include the above information marked on the outside of the container. 3. Miscellaneous parts shall be tagged or marked with the equipment item number of which they are intended.

6.0 6.1

ESP-A-1210.doc

Pgina 4 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

No.
GAS Y PETROQUMICA BSICA
GERENCIA DE PROYECTO Y CONSTRUCCIN

ESP-A-1210

SECCIN DE DESHIDRATACIN, REGENERACION Y FILTRADO


ESPECIFICACIN DE PROCESO

REV.

Fecha: ABR-02

4. Equipment containing insulating oils, antifreeze solutions or other fluids shall be prominently tagged at openings to indicate both in Spanish and English the nature of the contents, and shipping and storage precautions. 6.2.7 (Addition) Packing 1. All equipment shall be packed, securely anchored (skid mounted when required) and protected for shipment as indicated in the Purchase Order. All unmounted parts, except drivers, shall be suitably boxed and firmly attached to the main item for shipment. Unmounted drivers shall be shipped alongside the main unit. 2. For hydraulically operated pumps, the hydraulic fluid (when supplied with the pump) shall be shipped in separate cans or unbreakable bottles. 3. One complete set off Installation, Operating and Maintenance Instructions shall be packed and shipped with the equipment. These instructions are in addition to the sets specified in the Buyers form Sellers Drawing and Data Commitment. 8.0 8.2 8.2.1 VENDORS DATA Contract Data (Addition) Drawings, As -Built Data Sheets, Instructions and Operating Manuals and other data required shall be issued in accordance with the Additional Instructions to Supplier Drawing and Data Commitment Requirements, dated 16 Feb 95. Data (Addition) Spare parts quotations shall be submitted in accordance with the Buyers Specification ESP-A-1170 Spare Parts Requirements.

8.2.1 8.2.3.5

ESP-A-1210.doc

Pgina 5 de 9

En PGPB la ms alta prioridad es la seguridad de nuestros trabajadores, nuestros clientes, nuestros vecinos y el medio ambiente

Você também pode gostar