Escolar Documentos
Profissional Documentos
Cultura Documentos
This booklet is prepared for the Analog RGB Input function, provided as the optional function of V610T. The analog RGB input function displays the PC screen on V610T by connecting V610T to a PC via the connector (CN3).
5 10 15
1 6 11
2 3 4 5 6 7 8 9 10 11 12 13 14 15
Signals not indicated above cannot be input and displaying them on the V610T screen is not possible. To display the Windows screen, it is necessary to set the refresh rate to 60 Hz. An example of refresh rate setting procedure is shown below. Display the control panel by [Start] -> [Settings] -> [Control Panel]. In the dialog, double click the [Display] icon, then display the [Refresh Rate] item by [Display Properties] -> [Settings] -> [Advanced] -> [Adapter]. Set 60 (Hz) for this item. Note that the procedure for displaying the refresh rate setting item differs depending on the PC you are using. Please refer to the Users Guide of your PC for details of the setting procedure. If the cable connecting V610T (connector: CN3) to a PC is long, the display may vibrate due to noise. To eliminate adverse affect of noise, it is recommended to attach a ferrite core to the connection cable. 1
Screen Adjustment
Screen adjustment is necessary since RGB output frequency of the Windows screen, the BIOS screen, and the DOS screen may differ from each other for some PCs. If only one kind of output frequency is used, setting may be made for either Setting 1 or Setting 2. Adjustment procedure 1. Display the Main Menu screen.
V610T22
FONT VER.1.000/1.020/1.000 JAPANESE 32
1998- 9- 1
7 : 23 : 30
Error: Stop Time-Out: 0.50 sec Retry: 3 Baud Rate: 19200 Data Length: 7 Stop Bit: 1 Parity: Even Send Delay: 0msec
RGB Adjustment
Editor : MJ1
Memory Card
I/O Test
2. Display the RGB Adjustment screen by touching the [RGB Adjustment] switch.
V610T22
FONT VER.1.000/1.020/1.000 JAPANESE 32
1998- 9- 1
7 : 23 : 30
Error: Stop Time-Out: 0.50 sec Retry: 3 Baud Rate: 19200 Data Length: 7 Stop Bit: 1 Parity: Even Send Delay: 0msec
RGB Adjustment
Editor : MJ1
Memory Card
I/O Test
RGB Adjustment
Main Menu
About the way to adjust the display, refer to the manual. Horizontal: 31180 Hz Setting 1 Vertical: 59 Hz Setting 2
Not Used
Not Used
Adjustment
Adjustment
Clear
Save
3. First, carry out adjustments for the BIOS screen. Touch the [Adjustment] switch of Setting 1 to display the PCs BIOS screen in the RGB mode.
RGB Adjustment
Main Menu
About the way to adjust the display, refer to the manual. Horizontal: 31498 Hz Setting 1 Vertical: 70 Hz Setting 2
Used
Not Used
Adjustment
Adjustment
Clear
Save
Adjust the display with the [F1] to [F6] switches for the displayed BIOS screen.
[SYSTEM] [F1] [F2] [F3] [F4] [F5] Adjustment completed Vertical; screen scrolls down. Vertical; screen scrolls up. Horizontal; screen scrolls right. Horizontal; screen scrolls left. Dot; +1
BIOS screen
After the completion of adjustments, return to the RGB Adjustment screen by touching the [SYSTEM] switch.
4. Next, carry out adjustments for the Windows screen. Display the Windows screen at the PC before starting adjustments. After making sure that the input signal frequency at the RGB Adjustment screen matches the horizontal and vertical frequencies (Hz) of the Windows screen, touch the [Adjustment] switch of Setting 2 to display the Windows screen in the RGB mode.
RGB Adjustment
Main Menu
About the way to adjust the display, refer to the manual. Horizontal: 31180 Hz Setting 1 Vertical: 59 Hz Setting 2
Used
Used
Adjustment
Adjustment
Clear
Save
Adjust the display with the [F1] to [F6] switches for the displayed Windows screen.
After the completion of adjustments, return to the RGB Adjustment screen by touching the [SYSTEM] switch.
5. Touch the [Save] switch to save the settings. The contents of settings are written to the flash ROM.
RGB Adjustment
Main Menu
About the way to adjust the display, refer to the manual. Horizontal: 31180 Hz Setting 1 Vertical: 59 Hz Setting 2
Used
Used
Adjustment
Adjustment
Clear
Save
Bit 12 (RGB screen ON/OFF) [1] (ON level) : Turns the RGB screen ON. [0] (OFF level) : Turns the RGB screen OFF. Switching over by the macro command The macro command is used to turn the RGB screen ON/OFF. Usable devices
Internal memory F0 F1 Command name PLC memory Constant Memory card Indirect designation Double-word
(SET_RGB) F1
F1 + 0 0: OFF 1: ON
Bit 12 (RGB screen status display) [1] (ON level) : Indicates that the RGB screen is ON. [0] (OFF level) : Indicates that the RGB screen is OFF.
(RGB_CHG) F1
F1 + 0 0 : Setting 1 1 : Setting 2
Setting example The procedure below explains how to add the touch switch emulation function under the environment that uses the analog RGB input function. The procedure below assumes the following setting. At the RGB Adjustment screen Setting 1 ..... BIOS screen Setting 2 ..... Windows screen (For details of adjustments, refer to Screen Adjustment.) Connection COM2 of PC and MJ1 (editor port) of V6 by V6-CP (for screen data transfer) 1. Switch the V6 screen mode to the RGB input screen. (The Windows screen is displayed.) 2. Run V-SFTE and open the file presently transferred to the V6. 3. Select [System Setting] -> [Others] -> [Other Settings] -> [P2] -> [Modular Jack 2] -> [Touch Switch]. 4. Save the file and transfer it to V6. 5. Since V6 enters the RUN mode, switch the screen to the RGB input screen. (The Windows screen is displayed.) 6. To emulate the touch switches, connect the V6 MJ2 (touch switch) to COM1 (communication port) of PC with V6-CP cable. (Refer to item 4 in Cautions.)
V6
Editor port PC/AT compatible
MJ1 MJ2
Touch switch
V6-CP
COM1 COM2
7. In case of TOUCH PANEL DRIVER PN-WIN98/95 (Gunze): After inserting the TOUCH PANEL DRIVER PN-WIN98/95 (Gunze) floppy disk, double click A:\Serial\setup.exe. Then, install the touch panel driver following the instructions displayed on the screen. [Welcome!] -> [Select Destination Directory] -> [Ready to Install] -> [Hardware Controls] (see item 2 of Cautions below) -> [Installation Completed!] -> [OK] In case of TOUCH PANEL DRIVER U-TP (Gunze): After inserting the TOUCH PANEL DRIVER U-TP (Gunze) floppy disk, double click setup.exe. Then, install the touch panel driver following the instructions displayed on the screen. [Welcome!] -> [Select folder] -> [Select Destination Directory] -> [Install system tray icons.] -> [Number of devices (set to 1.)] -> [Define device #1 (as default, Whole Desktop and Device 1 )] -> [Please select the controller type for Device 1 (select Gunze, AHL, Serial )] -> [Please select the port for Device 1 Controller (select Auto Detect )] -> [Ready to Install] -> (installation starts)
With the operation above, the PC automatically reboots and, at the same time, V6 enters the RUN mode. Switch the display mode of V6 to the RGB input screen and boot Windows. 8
8. The calibration software automatically starts at the booting of Windows. Set the calibration data. (Refer to item 3 of Cautions below.) This completes the installation of the touch-panel driver. 9. To set the TOUCH PANEL DRIVER PN-WIN98/95 (Gunze) again, start the touch-panel driver by clicking the menu items in the sequence of [Start] -> [Programs] -> [Gunze] -> [PNWIN98_95 Serial] -> [Touchpanel Driver]. If the setting is changed, the new setting is enabled when the PC is run next. To set the TOUCH PANEL DRIVER U-TP (Gunze) again, start the touch-panel driver by clicking the menu items in the sequence of [Start] -> [Programs] -> [Gunze] -> [U-tp] -> [Calibrate]. If the setting is changed, the new setting is enabled when the PC is run next.
Cautions 1. Using the Windows screen displayed at V6, it is not possible to change the screen to the Main Menu screen. 2. When installing the touch-panel driver, setting is necessary using the [Hardware Controls] dialog. [Com port] Select the COM port of the PC to be connected to the V6 MJ port (for touch switches). [I/O Address] Designate the address of the selected COM port. [IRQ] Designate the IRQ of the selected COM port. If the COM port to be connected to the MJ port of V6 and its address and IRQ are unknown, refer to the Users Guide of your PC. For the items below, setting is fixed. [Baud Rate: 9600], [Pality: None], [Data Bits: 8], [Stop Bits: 1] 3. Correct the positional offset between the touch position and the mouse cursor display position using the calibration software. Touch the red X symbol displayed at the four corners of the screen in the following order as precisely as possible: 1st point (lower left corner of the screen) -> 2nd point (upper right corner of the screen) -> 3rd point (lower right corner of the screen) -> 4th point (upper left corner of the screen). Make sure to touch all of these four points. Since operation using the touch switches is not allowed if the calibration setting is not successful, repeat calibration operation if the first attempt was not successful. 4. Once you install the touch-panel driver, the serial port used for the installation cannot be used for other applications until the touch-panel driver is uninstalled or the port setting is released with adjustment setting. 5. If the PC has only one COM port, use another PC for transferring the screen to V6. 6. About the way to use the adjustment setting of U-TP, refer to the HELP menu of GUNZE. (Normally, use the default setting.)
1031NE0
10500000
12