Escolar Documentos
Profissional Documentos
Cultura Documentos
1-Which three actions are performed during the boot sequence of a Cisco switch? (Choose three.)
The boot loader uses the self-contained switch operating system to boot the switch.
The boot loader initializes the flash file system that is used to boot the system.
The boot loader loads the default operating system if the flash-based operating system is corrupt or missing
sticky
protect
restrict
shutdown
Refer to the exhibit. Both switches are configured with default bridge priority. Which port will act as the
STP root port if all links are operating at the same bandwidth?
Fa0/1 interface of S1
Fa0/2 interface of S1
Fa0/1 interface of S2
Fa0/2 interface of S2
Refer to the exhibit. Hosts PC_A and PC_B send traffic simultaneously, and the frames from the
transmitting stations collide. What is the last device to receive the collision?
hub HB1
switch SW1
router R1
switch SW2
router R2
switch SW4
This allows the switch to host web pages for the network.
This allows remote VPN connections to the switch over the Internet.
Refer to the exhibit. A new host needs to be connected to VLAN 1. Which IP address should be assigned
to this new host?
192.168.1.11 /28
192.168.1.22 /28
192.168.1.33 /28
192.168.1.44 /28
192.168.1.55 /28
What will be the effect of the command S1# copy system:running-config tftp://172.16.2.155/tokyo-
config?
The configuration file named tokyo-config will overwrite the startup configuration file on S1.
The running configuration file on S1 will be saved via TFTP to a file named tokyo-config.
The contents of NVRAM on S1 will become the startup configuration file on the tokyo switch.
Refer to the exhibit. What are two reasons for the Fa0/24 port being placed in the blocking state? (Choose
two.)
The Fa0/24 port is overloaded with too much traffic for its configured bandwidth.
How does a switch that is configured for 802.1Q trunking handle untagged frames that are received on a
trunk port?
zero
four
five
eight
nine
reduces administrative overhead by sharing VLAN databases between switches across the network
Refer to the exhibit. What would happen if the network administrator moved the network cable of Host A
from interface Fa0/1 to Fa0/3 on switch SW1?
Host A remains a member of VLAN 10, because the router is routing traffic between VLANs.
Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to VLAN
30.
Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for
the port.
Host A maintains connectivity to all members of VLAN 10, because it is connected to the same
physical network.
Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now a member
of VLAN 1.
Refer to the exhibit. All trunk links are operational and all VLANs are allowed on all trunk links. An ARP
request is sent by computer 5. Which device or devices will receive this message?
only computer 4
Introduce a Layer 3 device or a switch with Layer 3 capability into the topology.
Utilize the switchport trunk allowed vlan all command on switch 101-3FL to permit the VLAN traffic.
Apply IP addresses that are in the same subnet to the interfaces that are used to connect switches 101-2FL and 101-3
VLAN 20 only
All the VLANs were pruned from the trunk port between SW1 and SW2.
SW1 and SW2 cannot be both set as VTP servers in the same VTP domain.
VTP configuration revision number of SW2 was higher than the configuration revision number of SW1.
The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain.
Which three statements are true regarding router-on-a-stick inter-VLAN routing? (Choose three.)
can impact performance if many VLANs compete for bandwidth on a single router interface
makes troubleshooting the inter-VLAN routing configuration much less complex than when using
multiple physical interfaces
Refer to the exhibit. The devices in the network are operational and configured as indicated in the exhibit.
However, hosts A and D cannot ping each other. What is the most likely cause of this problem?
VLAN 20 and VLAN 30 are not allowed on the trunk between the switches.
Refer to the exhibit. Hosts A and B attempt to transmit a frame at the same time and a collision occurs.
When will host D be able to transmit?
immediately
after the jam signal clears and its backoff delay expires
Refer to the exhibit. Both switches are interconnected via a trunk link. Host A and host B are on the default
VLAN but are not able to exchange traffic. What should be done to fix the problem?
An administrator is viewing the running configuration for a switch on the network. The enable password is
displayed in plain text but the enable secret password has been encrypted. What level of access can be
gained using the enable password?
full access to privileged mode if the enable password and the enable secret password are the same
Refer to the exhibit. A network administrator configures HyperTerminal with the parameters shown but is
unable to connect to a switch via the console port. The administrator is using a tested rollover cable
attached to the only COM port on the computer, and the connections have been verified. What is the likely
problem?
Refer to the exhibit. Which three options correctly identify information that could be associated with this
output?(Choose three.)
The router will forward the packet out interface FastEthernet 0/1.1.
The router will forward the packet out interface FastEthernet 0/1.2.
The router will forward the packet out interface FastEthernet 0/1.3.
The router will forward the packet out interface FastEthernet 0/1.2 and interface FastEthernet 0/1.3.
Refer to the exhibit. What does "FORWARDING" mean in the command output shown?
The switch is receiving BPDUs and populating the MAC address table, but not sending data.
lowest bridge ID
Refer to the exhibit. The network administrator is planning five additional VLANs to be shared throughout the
VTP domain on S3. What action should the administrator take before creating the additional VLANs?
Create the VLANs on a switch in VTP server mode and allow them to propogate to the other switches in
the domain.
Enable the VTP pruning mode in order to create the VLANs on S3.
probing
beaconing
association
authentication
SSID
OFDM
WEP
DSSS
Associate with the access point and then open a HyperTerminal session with the access point.
Physically connect to the access point and then reboot the computer to launch the configuration
software.
From a computer in the same IP subnet as the access point, enter the default IP address of the
access point in a web browser.
Modify the TCP/IP properties of the computer connected to the access point so that it exists on the
same network, and then reboot your computer to establish a connection.
Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network
Mode option Mixed mean?
Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet con
How should the network administrator change the displayed configuration to satisfy the requirement?
Increase the capacity of the distribution and core trunk links to 10 Gb/s.
IP address
MAC address
bridge priority
VLAN ID
port priority
Using lower bandwidth connections between switches will allow STP to have a larger network
diameter.
Portfast can be used to increase the allowable switched network diameter because it disables the
forward delay and maximum age timers.
Divide the computers into separate workgroups using different physical switches.
client
root
server
transparent
Refer to the exhibit. A wireless infrastructure has been established in a company building as shown. The
design goal was to allow roaming between the three APs for handheld devices. However, the devices lose
connectivity when the users roam. How can this problem be fixed?
Reposition the APs so that each area of signal strength overlaps the neighbor by at least 10-15%.
DSSS
OFDM
SSID
WPA
Refer to the exhibit. What is the effect of setting the security mode to WEP on the Linksys integrated
router?
WEP encrypts data between the wireless client and the access point.
WEP ensures that only authenticated users are allowed access to the WLAN.
WEP translates an internal address or group of addresses into an outside, public address.
After listening for the presence of a signal on the network media, hosts A and C transmit data at the same
time. In what two ways do the hosts respond to this situation? (Choose two.)
The hosts transmit a jam signal to ensure that all hosts on the network are aware that a collision has
occured.
Because they are operating in full-duplex mode, the hosts resume listening for traffic in preparation
for sending future messages.
Because the hub will temporarily block traffic from one of the hosts, that host will be allowed to
transmit once the wire is clear.
Hosts A and C are assigned shorter backoff values to provide them priority to access the media for
retransmission.
After the backoff period of a host, the host checks to determine if the line is idle before retransmitting.
The clear mac-address-table command will remove statically and dynamically configured table entries.
The erase flash command will clear all statically configured table entries.
Statically configured MAC addresses will automatically be removed from the address table 300 minutes after the last ac
switch port.
Parte inferior do formulário
Refer to the exhibit. What does STATIC indicate in the output that is shown?
MAC address 0001.637b.b267 was learned from the source address of a frame that was received on
switch port Fa0/24.
MAC address 0001.637b.b267 was manually associated with the switch port Fa0/24.
Which three statements are correct regarding passwords configured on a switch? (Choose three.)
The enable password is used if the enable secret password is not set.
The enable password command is more secure than the enable secret command.
The service password-encryption command is entered in global configuration mode and only
encrypts global configuration mode passwords.
The service password-encryption command applies encryption to all passwords normally displayed
in plain text by the show running-config command.
Parte inferior do formulário
Parte inferior do formulário
Parte inferior do formulário