Escolar Documentos
Profissional Documentos
Cultura Documentos
Pipe Size and Weight: Pipe Grade: Range: Tool Joint: New (Nominal) 4.000 0.330 3.340 12.935 399,500 32,600 26,100 15,159 15,896
4.000" 14.00ppf 0.330" wall IU CYX105-120 2 4.875" X 2.688" XT39 New (Nominal) 3.805 12.566 8.762 3.229 6.458 API Premium 2.989 11.751 8.762 2.523 5.046
Pipe Body Premium 3.868 0.264 3.340 10.162 313,900 25,500 20,400 13,860 11,622
OD (in) Wall Thickness (in) Nominal ID (in) Calculated Plain End Weight (lbs/ft) Tensile Strength (lbs) Torsional Strength (ft-lbs) 80% Torsional Strength (ft-lbs) Burst Pressure (psi) Collapse Pressure (psi)
Cross Sectional Area of Pipe Body (in2) 2 Cross Sectional Area of OD (in ) Cross Sectional Area of ID (in2) 3 Section Modulus (in ) Polar Section Modulus (in3)
Notes: Pipe Properties are calculated based on uniform OD and wall thickness New = 100% RBW. Premium = 80% RBW Burst Pressure for New based on 87.5% RBW per API
OD (in) ID (in)
4.875 2.688
Drill Pipe Assembly with Grant Prideco XT39 eXtreme Torque Connection New
(New guaranteed 95% RBW Pipe with IPC)
Pin Tong Length (in) Box Tong Length (in) Torsional Strength (ft-lbs) Max Recommended Make-up Torque (ft-lbs) Min Recommended Make-up Torque (ft-lbs) Tensile Strength at Max Recommended MUT (lbs) Tool Joint/Drill Pipe Torsional Ratio (New Pipe) Tool joint/Drill Pipe Torsional Ratio (Premium Pipe) Balance OD (in) Minimum OD for Premium (in)
12.0 15.0 35,300 21,200 17,700 553,300 1.08 1.39 4.926 4.652
Adjusted Weight (lbs/ft) Approximate Length (ft) Fluid Displacement (gal/ft) Fluid Capacity (gal/ft) Fluid Capacity (bls/ft) Drift Size (in) Max Upset OD (in)
0.43 0.010
Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of 95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill tolerances, internal plastic coating tolerances, and other factors. New pipe guaranteed to 95% RBW will have a smaller ID (3.285'') than new pipe guaranteed to 87.5% RBW
Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100 psi A raised elevator OD increases elevator capacity without affecting make-up torque
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT. JCT 03-21-2011
TorqueTensionGraph
Connection:XT39(4.875(in)ODX2.688(in)ID)SMYS=120,000(psi) PipeBody:80%InspectionClass,4.000(in)OD,0.330(in)wallthickness,CYX105120PipeGrade (safetyfactor=1.0)
700,000
PipeBodyinCombinedLoading
PipeBodyYieldat80% InspectionClass
600,000
ConnectionPerformance(basedonMUT)
ToolJointYield 500,000 ToolJointShoulderSeparation TJOperationalLimit(RecMUT)
Tens sion(lbs)
TJOperationalLimit(MinMUT) 400,000
300,000
200,000
100,000
Torque(ftlbs)
ConnectionWearforXT39(4.875(in)ODX2.688(in)ID)
MaterialSMYS(specifiedminimumyieldstrength)=120,000(psi)
40,000
35,000
30,000
Connection
25,000
TorsionalStrength RecommendedMUT
Torque(ftlbs) T
20,000
MinimumMUT
15,000
PipeBody
80% ofPremiumPipe BodyTorsionalStrength
10,000
PipeBody:4.000(in)OD,0.330(in)wall thickness,CYX105120PipeGrade
5,000
ToolJointOD(in)