Escolar Documentos
Profissional Documentos
Cultura Documentos
Current transformers type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
This installation, use and maintenance guide is valid for current operating in outdoor or indoor conditions. These instructions are valid for current transformer type: TPO, KOHU, TPU, IBZ, IPZ, ISZ, IMT, KOKU, KODI, IP 24
Indoor transformers The transformers should be mounted in dry indoor conditions where the ambient air is not signicantly polluted by dust, smoke, corrosive gases, vapors or salt. The transformers are designed for standard ambient temperature between 5C and +40C. The transformers may be used also in higher or lower ambient temperatures and higher altitudes when agreed between the manufacturer and purchaser. Outdoor transformers The transformers should be mounted in outdoor conditions where the ambient air may be polluted by dust, smoke, corrosive cases, vapors or salt. The transformers are designed for standard ambient temperature between 60C and +55C. The average value of the ambient temperature, measured over a period of 24 hours, should not exceed 35C.
Index
Instruction for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Primary reconnectable transformers. . . . . . . . . . . . . . . . . . . . . . . 6 Capacitive voltage indicator (divider). . . . . . . . . . . . . . . . . . . . . . . 8 Indicative power losses on the secondary circuit cables .. . . . . . . 8 Instruction for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Instruction for maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package, transport and storage . . . . . . . . . . . . . . . . . . . . . . . . . 8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Handling with the transformers . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Wiring diagram examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Dimensions drawing .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 TPO 6x. xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 TPO 7x. xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 KOHU 24 A1 (A2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TPU 4x. xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 TPU 5x. xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TPU 6x. xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 IP 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 IPZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 ISZ 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ISZ 17 (160 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ISZ 17 (260 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 KODI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 KOKU 072 G3 (G4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 KOKU 072 G5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 KOKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 IMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
No voltage inspection Inspection should be done periodically, depending on local conditions, but at least twice a year. These inspection include: 1. measurement of the resistance of the winding insulation or secondary windings together with secondary circuits, which value can not be less than 10 M (megaohms), 2. cleaning of the external surfaces of the transformer, 3. complement of the coat, 4. checking of holding-down of the xing, terminal and grounding bolts. NOTES a) All electrical tests listed in these instructions should be done in accommodations meeting the requirements given in the catalogue card in consideration of the ambient temperature and the humidity. b) Maintenance of the transformers should be done in accordance with the safety and occupational hygiene requirements contained in Heavy Current Engineering Equipment Operating Rules.
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 3
Safety instructions
1. Always consider transformer as a part of the circuit to which it is connected, and do not touch the leads and terminals or other parts of the transformer unless they are known to be grounded. 2. Always ground the metallic bases of instrument transformer. 3. Always ground one secondary terminal of the transformer. When the secondary of transformer is interconnected, there should be only one grounded point to prevent accidental paralleling with system grounding wire. In case of disconnection from the ground, the grounding screw has to be removed from the secondary terminal. One should earth: a) the star point of the scheme of connections Y, b) the joint point of two transformers of the scheme of connections V, c) one of two joint points of Holmgrens scheme, d) start point of both Y in the differential longitudinal scheme. If the transformers supply electricity meters it is recommended that the earthing point should be from the side of the ow of the electric energy. Ground terminal can be optionally chosen from each secondary winding in compliance with principles of scheme of connection. This connection can be done by screwing in the ground screw into an optional whole of the winding terminal (if it is possible).
Recommended order of installing of the transformer in the current circuit: 1) bars to the transformer, 2) the transformer with bars to the base. 4. Always short-circuit the secondary of the current transformer, which is not currently in use to prevent secondary voltages which may be hazardous to personnel or damaging to the transformers secondary. The secondary like this must be additionally grounded. 5. In case of the current transformer with voltage indication (coupling electrode included) is secondary terminal box equipped with PE terminal, which is connected with earthing screw to the base plate, which must be generally earthed. Connection between secondary terminal and base plate is shown on the picture Crossection of single line terminal box.
Attention: Terminal PE must be always earthed, this is hold generally, even if the base plate is removed. In case of disassembling the base plate, producer doesnt warranting the earthing.
4 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
Technical details
The technical details for each individual transformer are mentioned on the rating plate fastened on the transformer. Values mentioned on the rating plate must not be exceeded. Markings used on the rating plate are as follows: Example of outdoor current transformer label 74x62 mm
Mounting Following information is general and some details can differentiate according to type and variants of transformers. It is necessary to combine it with other technical and marketing specications like catalogues, dimensional drawings and rating plate for specic transformer type. Indoor current transformers The mounting position of the indoor transformer can be freely chosen. The transformer is xed using the mounting base with four screws M10 and washers. Fastening must be done on a smooth surface. There is a M8 screw for earthing the transformer on the base plate. Outdoor current transformers The mounting position of the outdoor transformer is only horizontal. The other position can be agreed with the supplier. The transformer is xed using two proles with M12 screws. Fastening must be done on a smooth surface. There is a M12 screw for grounding of current transformer. Primary connection Primary terminals of the current transformer are made of cooper and they are silver or tin plated. There are M12 screws used for fastening of primary conductor to the terminal. For primary reconnectable transformers the ratio can be reconnected by changing position of the links xed by M12 (outdoor) or M8 (indoor) screws without removing already tted primary conductors. Maximum allowed torques for screw connections of current transformers:
Screw M5 M6 M8 M10 M12 Max. torque [Nm] 3.5 4 20 35 70 Min. torque [Nm] 2.8 3 16 20 56
Where:
Parameters 1YMP011TPO00005 Description serial number serial number barcode EFN 128 340056#10 TPO 73.11 50 Hz 40C 1250//1/1/1/1 A 120% 1S1-1S2 2S1-2S2 3S1-3S2 4S1-4S2 10 VA, 15 VA 0.2S, 10P, PX FS5, 10 36/70/170 kV order number transformer type code rated frequency ambient temperature rated transformation ratio extended primary current terminal marking for core number 1 terminal marking for core number 2 terminal marking for core number 3 terminal marking for core number 4 rated output accuracy classes instrument security factor (FS), accuracy limit factor (ALF) rated insulation level (highest voltage for equipment / power-frequency withstand voltage / rated lightning-impulse voltage) IEC 60044-1 16 kA/3 s 40 kA 2011 E referred standard(s) rated short-time thermal current (thermal time) / rated dynamic current year of production temperature class
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 5
TPO
TPU
In case of Bus CT, there must be always connected CT shielding to the primary bar. Connection must be done via wire 2,5mm2. One example of ISZ 17 shielding connection is described on the picture
6 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
Secondary connections The terminals, screws, nuts and washers are made of stainless steel. Secondary grounding screws and secondary terminal fastening screws are made of nickel-plated brass. The secondary terminal cover box for outdoor CT is made of epoxy resin and provided with one insert Pg21. The secondary terminal cover box for indoor CT is made from the plastic and provided with three detachable threaded inserts Pg16.
The terminals are provided with M6 or M5 screws for secondary wiring connection and with through going holes for direct earthing of the secondary circuit by M6 or M5 screws. The terminal cover is seal able. Degrees of IP protection Outdoor transformers: IP54 Indoor transformers: IP40
IBZ 12b, 17b, 24b terminal boxes at the bottom (max. 4 terminals)
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 7
The sum of power losses at the terminals on the secondary circuits. Contact resistance is not constant at time due on the oxidation of the contact surface and the layer thickens powdery deposits. Generally you can take the following values for one contact: Rz = 10m for the devices connected tothe outdoor instrument transformers. Rz = 5m for the devices connected tothe indoor instrument transformers.
No. points of contact 1A 4 6 8 10 12 0.04 0.06 0.08 0.10 0.12 Consumption [VA] Outdoor 5A 1 1.5 2 2.5 3 1A 0.02 0.03 0.04 0.05 0.06 Consumption [VA] Indoor 5A 0.5 0.75 1 1.25 1.5
8 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
Disposal
Materials used in instrument transformers are considered as materials without dangerous environmental impact and materials are not toxic. Disposal of instrument transformers is controlled by national legislation of communal waste.
Handling by the belt Transformers where it is possible, from safety reasons, can be handling by hanging on the belts. Than the handling can be done by hanging of the transformer on the crane.
Spare parts
The construction of cast resin insulated current transformers does not consider spare parts.
Warranty
The factory grants 24 months of warranty from the day of put to use of the transformer, but no longer than 30 months from the day of sell. The warranty concerns only manufacturing defects and does not include defects arose because of: - improper transport, improper storage, not abiding of the instruction before installing and during operating of the transformers, improper selection of the transformer for the electric power system.
Safety warning! Lifting capacity of the hooks and the crane has to be 200kg at least. Always make sure that the hooks hold safely on the crane and on the transformer.
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 9
Handling by the self-locking hooks under primary screws. In case of indoor current transformers, which are equipped with primary terminal screws M12, there is possible to hanging the transformer on with self-locking hooks holding under primary. The handling can be done by hanging of the hooks on the crane. Note. This system is recommended for types: TPU, IMZ, IBZ.
SAFETY WARNING: During the manipulation with transformer is necessary to follow safety work instructions. Never stay under the freight. Always make sure that the freight is safely locked on the crane and make sure that there is no risk of unexpected release or turnover of the freight. Note: Holding jigs, described in these chapters, are not a part of delivery.
Safety warning! Lifting capacity of the hooks and the crane has to be 200kg at least. Always make sure that the hooks hold safely on the crane and on the transformer. Handling by the chain and crane. All transformers which are equipped with the two U proles and hanging screws are possible to handle by using chains and crane. Screw hanging screws M12 into the U proles and hang on the crane by chains as it is shown on the picture.
Normative references
Current transformers are designed, tested and produced according to international or national standards required by customers and agreed by producer. Specic standard is always mentioned on the Rating plate of transformer.
IEC 600441 IEC 60529 ISO 12100 EN 501101 Instrument transformers Current transformers Degrees of protection provided by enclosures (IP Code) Safety of machinery Basic concepts, general principles for design Operation of electrical installations
For example these standards: IEC 600441; IEC 600446 GOST 1516.396; GOST 77462001 PN EN 600441; PN EN 600446 AS 600441; AS 16751986 IEEE Std C57.13.62005 ANSI C57.131978 CSA Std CAN3-C13-M83 BS 3939:1973; BS EN 600441
If it is agreed between customer and producer is possible to deliver also other standard or standards which are mention above with different revision.
Note. This system is recommended for most transformers with weight more than 40kg mainly for types: TPO. Safety warning! Lifting capacity of the chains, loops and the crane has to be 200kg at least. Always make sure that the loops and chains hold safely on.
10 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
II cores:
P1 P2
S1
S2
1S1
1S2
2S1
2S2
III cores:
VI cores:
P1
P2
P1
P2
1S1
1S2
2S1
2S2
3S1
3S2
1S1
1S2
2S1
2S2
3S1
3S2
4S1
4S2
I core:
C1 C2
II cores:
C1 C2
P1
P2
P1
P2
S1
S2
1S1
1S2
2S1
2S2
III cores:
C1 C2
P1
P2
1S1
1S2
2S1
2S2
3S1
3S2
P1
P2
P1
P2
S1
S2
S3
1S1
1S2
1S3
2S1
2S2
2S3
Note. The number of secondary windings (from 1 to 4 - up to 12 secondary terminals), depends on the combination of technical parameters, such as the accuracy class, burden, short-circuit current, short-thermal current and size of the transformer.
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 11
Dimensions drawing
TPO 60.11
440 ( 239)
S (1:4)
18 60 2x 14
60
459
382
(77)
10
32
A (1:4)
A M6 PG21 IP54 100 25 M 12 195 290 420 380 350 32 4 x M 12 x 35
4x 14
50 100 195
60
58
TPO 60.12
440 ( 239)
S (1:4)
60 2x 32 18 14
60
382
459
(77)
10
A (1:4)
A M6 PG21 IP54
25
M 12
195 290
350
420
380
32
4 x M 1 2 x 35
4x
14
50 100 195
60
58
100
TPO 61.11-63.11
S (1:4)
80 20 40 4 x
60
445
357
(88)
10
40
14
A (1:4)
A M6 PG21 IP54
25
M 12
195 290
420
380
350
4 x M 1 2 x 35
4x
14
50 195
40
80
58
100
TPO 64.11-66.11
S (1:4)
100 45
4 x
14
472
357
( 115) 16
45
60
A (1:4)
M6
32
120
M 12
420
380
350
4x
8x M 12 deep 25
14
50 195
100
40
TPO 70.11
PG21 IP54
4xM12x35
TPO 70.12
PG21 IP54
4xM12x35
TPO 71.11-76.11
PG21 IP54
8xM12x35
KOHU 24 A1 (A2)
P2
B
4xM10
P1
B
406 446 2xM10 79.5 1,6 m
341
90
11
40
25
51 97
14
50 16 23 30 11
B-B 1:3
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 19
TPU 40.12
20 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
TPU 40.14
Masa: 2024 kg
Weight: 20-24 kg
Masa: 2024 kg
Weight: 20-24 kg
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 21
TPU 44.11 TPU 45.11 TPU 46.11 TPU 47.11 TPU 48.11
TPU 44.13 TPU 45.13 TPU 46.13 TPU 47.13 TPU 48.13
TPU 44.11 TPU 47.11 TPU 45.11 TPU 48.11 TPU 46.11
Masa: 2528 kg
Weight: 25-28 kg
22 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
TPU 50.12
Masa: 2024 kg
Weight: 20-24 kg
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 23
TPU 50.14
Masa: 2024 kg
Weight: 20-24 kg
Masa: 2024 kg
Weight: 20-24 kg
24 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
TPU 60.12
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 25
TPU 60.14
Masa: 3135 kg
Weight: 31-35 kg
Masa: 3135 kg
Weight: 31-35 kg
26 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
TPU 64.11 TPU 65.11 TPU 66.11 TPU 67.11 TPU 68.11
TPU 64.13 TPU 65.13 TPU 66.13 TPU 67.13 TPU 68.13
Masa: 3641 kg
Weight: 36-41 kg
Masa: 3641 kg
Weight: 36-41 kg
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 27
Weight: 31-35 kg
28 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
IP 24
Secondary terminals M6
Rating plate
80
12,5
12,5
50
1
74 , 5
65,5
0,
285
16 8
15 0
,5
M10
20
17 22
17
12
12
30 92 120
22
20
19 M6
R10 R3
10
R3
Tabliczka znamionowa
Zaciski wtrne M6
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 29
55
IPZ
Um=12 kV IPZ 10-2A Ipn [A] 200 800 Weight (aprox) [kg] g [mm] I1 [mm] I2 [mm] I3 [mm] 21 8 510 1000 2000 26 12 610 350 178 200 800 25 8 510 1000 2000 30 12 610 200 800 24 8 710 IPZ 10-3A IPZ 20-2A
U m=24 kV IPZ 20-3A Ipn [A] 1000 2000 30 12 810 550 260 200 800 28 8 710 1000 2000 34 12 810
2)
4 x 15 2)
4 x 13 4)
Note: 1) Seal wires: Cu Ag 12 m 2) Standardized machine elements: cup washers: Fe (Cu 3 m + Sn 10 m) other elements: brass No 10m 3) Secondary terminals: brass Ni 10 m standardized machine elements M6: acc. point 2. 4) 4 holes fro screw M12 Deviation of nontoleranced dimensions are maximum 3%. Manufacturer reserves for himself the right to train the changes issued from the technological progress.
30 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
ISZ 10
6)
6)
1)
1)
4)
4)
5)
3)
5)
Note: 1) Aluminium insert (2 pcs shown shape for I1n=3000 A) 2) Secondary terminals: brass Ni 10 m Standardized machine elements M6: spring washer: Fe m (Cu 3 m + Sn 10 m) other elements: brass Ni 10 m 3) Standardized machine elements (M8): Fe Zn 12 m 4) Metallic cap 5) Diamagnetic plate 6) Mounting elements see Equipment Deviation of nontoleranced dimensions are maximum 3%.
Kind of insert (acc. PBUE brochure 10, tab. 24) 2 x AP 80 x 10 290 3 x AP 100 x 10 4 x AP 100 x 10 4 x AP 120 x 10 330 290 413 245 240 370 216 a b c d
Dimension e f g h i
310
241
291
R30
27
355
291
331
R30
32
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 31
R 85
30
R 85
4xM12
30
60
4xM12
160
270
60
160
270 160
270
160 100 R8
2
45
R 40
1)
5 8
R8
160 100 R8
270 160
160
270
350
R 40
215 155
1)
R 20
6xM6
270
2xM4
160
350
45
R6 145 165 200
5 8
100 85
R8
215 155
R 20
6xM6
R6
2xM4
100
85
Note: 1) Nut M4 Shield of high potential must be always connected to the primary bar, by the wire min. 2,5mm2
32 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
R 85
R 85
30
30
4xM12
4xM12
160
270 160
45
160
2
370
160
160
370
260 200 R8
R 40
1)
270 160
215 155
160
270
5 8
R8 350
260
200
R6
R8
R 40
R 20
2xM4
160
270
215 155
350
45
6xM6
1)
200
85
5 8
R8
R 20
6xM6
R6
200
85
Note: 1) Nut M4 - Shield of high potential must be always connected to the primary bar, by the wire min. 2,5mm2
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 33
KODI
D
29
H E G
18
I
K L
J
Diameter / Type A B C D E F G H I J K L M KODI 1 PU 7 160 266 214 176 181 64 152 16 8 70 12 21 242 KODI 1 MN 7 140 246 197 176 171 64 142 16 8 70 12 21 227
C M
KODI 1 KK 7 120 226 181 176 161 64 132 16 8 70 10 17 206 KODI 1 HH 7 100 206 164 176 151 64 122 16 8 70 10 17 191 KODI 1 FG 7 80 186 152 176 141 64 112 16 8 70 10 17 178
34 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
P2
35
230
S1
S2
125
45
111 M12X60
S1
S2
M5
M5
13,3
S1 = 1 S2 = 2
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 35
KOKU 072 G4
KOKU 072 G5
3xM8
22
1)
50 1
Note: 1) Wire 2x2,5mm2 or 2x4mm2, color black marked with numer 1 and 2
36 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
50
68
30
KOKU 1_C_
124 52
20
B 2 (120...160)
B 2 (80...10 0)
40
11
142 M5 97 M5 Pk 16 Pr 22,5 Pg 16
64 16
IP54
P1
249 3
183 2
Di
+2 0
112 2
P1
17
P2
18
14
M8
S1
148
S2
Di =
Di = 33 A B= C=
42 B
60 D
70 E
85 F
KOKU 1 _ C __
B= C=
KOKU 1_F_
B (10 0 0...160)
B2 (160) B2 (60...140)
B2(80)
78
80
40
11
52 140 18 75
52 70
11
M5
142 97
M5 Pk 16 Pr 22,5 PG 16 16
64
P1
17
IP54
279 3
213 2
Di
+3 0
186 M8
131 2
P1
P2
18
14
S1
S2
170 Di = 33 A 8 B= C= 42 B 10 60 D 12 70 E 14 85 F 16 90 G 100 H
KOKU 1 _ F __
38 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
20
Di = 33 A
KOKU 1_H_
42 B
60 D
70 E
85 F
B= C=
11
52 140 64 M5 142 97 M5
Pk 16 Pr 22,5 Pg 16
16
IP54
P1
301 3
2352
Di
+30
17
200 M8
138 2
P1
P2
S1
S2
18
14
170
Di =
33 A
8
42 B
10
60 D
12
70 E
14
85 F
16
90 G
18
100 H
120 K
KOKU 1 _ H _
B= C=
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 39
B= C=
KOKU 1_J_
IP54
40 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
KOKU 1_K_
20
B 2
40
14
Pk 16 Pr 22,5 Pg 16
P1
341 3
2752
Di
+3 0
250 -2
15
158 2
17
18
P1
P2
M8 270
S1
S2
Di = 33 42 60 70 85 90 100 120 155 A B D E F G H K N 8 10 12 14 16 18 20 B = 80 100 120 140 160 180 200 C = 40 60 80 100 120 140 160
KOKU 1 _ K _
Di = 33 42 A B
8
B = 80 C = 40
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 41
KOKU 1_L_
20
B2
M6
54
P1
3633
17
P1
40
14
P2
297 2
Di
+3 0
S1
S2
270 -2
18
P2
15
M8
270
KOKU 1 _ L _
Di = 33 42 60 70 85 90 100 120 155 180 200 A B D E F G H K N R S
8 10 12 14 16 18 20
B = 80 C = 40
100 120 60 80
140 100
160 120
42 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
158 2
KOKU 1_M_
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 43
10
12
14
16
18
20
B = 80 KOKU 1_P_ C = 40
100 120 60 80
140 100
160 120
IP54
44 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
KOKU 1_T_
IP54
Note: Uwaga: Without xing base. Bez podstawy. Fix directly to oor
do podogi
Monta bezporednio
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 45
KOKU 1_W_
IP54
Note: Uwaga: Without xing base. Bez podstawy. Monta bezporednio Fix directly to oor do podogi
46 Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24
IMT
appr.44 44 ok.
M6
34
2 przewd x 2,5 dugoci wire 2 2 x 2.5 mm2mm with a o length of 4 m, 4 m, oznaczany nr 1 i 2 "1" and "2" marked with number
A 53 73 95
C 55 45 45
D 85 100 112
E 70 85 97
Current transformers Type: TPO, TPU, IBZ, IPZ, ISZ, KOHU, KOKU, KODI, IMT, IP 24 47
ABB Sp. z o.o. Branch in Przasnysz 59 Leszno Str. 06-300 Przasnysz, Poland Phone: +48 29 75 33 377, +48 29 75 33 233 Fax: +48 29 75 33 327 www.abb.pl
We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction in whole or in parts is forbidden without ABBs prior written consent. Copyright 2012 ABB All rights reserved
We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsi bility whatsoever for potential errors or possible lack of information in this document.