Escolar Documentos
Profissional Documentos
Cultura Documentos
)Basic Wind Speed (m\Hr )Basic Wind Speed (Km\Hr )Basic Wind Speed (m\Sec )Wind Pressure (psf ) Wind Pressure (Kg\m ) Wind Pressure (N\m ) Wind Pressure (KN\m
2 2 2
Pe= Ce . k . q
CW02
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.4 Mass Properties (Unit) Area(cm2): Moment of Inertia - Ix (cm ): Moment of Inertia - Iy (cm ): Elastic modulus - Zx (cm ): Elastic modulus - Zy (cm3):
3 4 4
4 Geometry:
Width of Loading Area(m)
Distance btwn fixing two points Vertically(m) Effective Wind Area(m )
2
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 2.75 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor(l) Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.13 1.52 1.72 5.50 6.51 1.69E-04 38,432.40 103,030.30 0.37 0.0240 Stress SAFE UNSAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3): Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection
CW04
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.1 Mass Properties (Unit) Area(cm ): Moment of Inertia - Ix (cm ): Moment of Inertia - Iy (cm ): Elastic modulus - Zx (cm3): Elastic modulus - Zy (cm ):
3 4 4 2
4 Geometry:
Spacing bet. Vertical elements (cm) Typical Floor Hight (cm)
Effective Wind Area(m )
2
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 2.00 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.24 1.00 1.24 4.00 2.48 3.43E-05 72,374.39 103,030.30 0.70 0.0239 Stress SAFE SAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3): Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection
CW12
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.2 Mass Properties (Unit) Area(cm ): Moment of Inertia - Ix (cm ): Moment of Inertia - Iy (cm ): Elastic modulus - Zx (cm3): Elastic modulus - Zy (cm ):
3 4 4 2
4 Geometry:
Spacing bet. Vertical elements (m) Typical Floor Hight (m)
Effective Wind Area(m )
2
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 2.30 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.38 1.17 1.62 4.60 4.27 1.14E-04 37,587.73 103,030.30 0.36 0.0164 Stress SAFE SAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3) Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection
CW10
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.1 Mass Properties (Unit) Area(cm ): Moment of Inertia - X (cm4): Moment of Inertia - Y (cm ): Elastic modulus - Zx (cm ): Elastic modulus - Zy (cm ):
3 3 4 2
4 Geometry:
Spacing bet. Vertical elements (m) Typical Floor Hight (m)
Effective Wind Area(m2)
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 1.85 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.24 1.70 2.11 3.70 3.61 1.14E-04 31,710.30 103,030.30 0.31 0.0090 Stress SAFE SAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3): Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection
CW05
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.2 Mass Properties (Unit) Area(cm ): Moment of Inertia - X (cm4): Moment of Inertia - Y (cm ): Elastic modulus - Zx (cm ): Elastic modulus - Zy (cm ):
3 3 4 2
4 Geometry:
Spacing bet. Vertical elements (cm) Typical Floor Hight (cm)
Effective Wind Area(m2)
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 2.00 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.24 2.10 2.60 4.00 5.21 1.14E-04 45,781.21 103,030.30 0.44 0.0151 Stress SAFE SAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3): Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection
CW14
1- Introduction:
This document presents the analysis method and design criteria for Aluminum frame sections for the curtain walls used for buildings facades in Girls Institutes in Namas District. The vertical members of curtain walls are supported on each floor slab , the support condition of vertical members are similar to the behavior of continuous beam.
2- Material:
For the 6063-T6 alloy: Density(g)= Tensile Yield Strength (Fty) = Compressive Yield Strength (Fcy) = Tensile Ultimate Strength (Ftu) = E (elasticity) = 26 KN/m3 170,000 KN/m2 170,000 KN/m2 205,000 KN/m2 70,000,000 KN/m2
3- Sections:
The section shown on the right will be used SEC.4 Mass Properties (Unit) Area(cm ): Moment of Inertia - Ix (cm ): Moment of Inertia - Iy (cm ): Elastic modulus - Zx (cm3): Elastic modulus - Zy (cm ):
3 4 4 2
4 Geometry:
Spacing bet. Vertical elements (m) Typical Floor Hight (m)
Effective Wind Area(m )
2
5-Allowble Deflection:
Allowable deflection is the minimum of : - L/200 cm - 2.00 cm 4.10 cm
6 - Loads:
Self weight: It is automatically considered by the program, it can be neglected to be more conservative. Aluminum Density= 26 KN/m3 Glass Density=25 KN/m3 Wind load: From the attached map Basic Wind speed in Namas (m/sec)= Wind speed in Namas (m/sec)= Net Design Wind Pressure (KN/m2)= Importance Factor Mean Roof Hight (m) Exposure Category Exposure & Hight Factor Wind Pressure (KN/m )=
2
SBC 301 Fig.6.4-1 SBC 301 Fig.7.1-2 SBC 301 Tbl.6.5-1 SBC 301 6.4.2.3 SBC 301 Fig.7.1-2 SBC 301 Equ.7.1-2
1.18 1.30 1.53 5.50 5.78 1.69E-04 34,087.22 103,030.30 0.33 0.0213 Stress SAFE SAFE
Max moment on mollion(KN-m) Elastic modulus - Zx (m3): Stress(fb) (KN/m2) Allowable Stress(Fb) (KN/m2) Ratio Deflection Result Deflection