Escolar Documentos
Profissional Documentos
Cultura Documentos
14 Handover
14
About This Chapter
Handover
Handover is one of the basic functions of the GSM. It enables calls to be set up in better cells and reduces call drops. Handover also lowers cross interference. The handover procedure consists of handover triggering, handover preparation, handover decision, and handover execution. 14.1 Handover Procedure The handover procedure is categorized into the intra-BSC handover procedure, inter-BSC handover procedure, inter-MSC handover procedure, and inter-system handover procedure. 14.2 Internal BSC Signaling Procedure of Handover The internal BSC signaling procedure of handover is categorized by intra-BSC handover, interBSC handover, inter-MSC handover, and inter-system handover. 14.3 Abnormal Handover Cases This topic describes the abnormal handover cases.
Issue 01 (2007-11-26)
14-1
14 Handover
14-2
Issue 01 (2007-11-26)
14 Handover
Channel Activation(3) Handover Access(6) FACCH Start T3124 Handover Access FACCH PHY INFO(8) FACCH Stop T3124 SABM(9) FACCH UA(11) FACCH FACCH Handover Complete(12) Establish Indication(10) Channel Activation Acknowledge(4)
Measurement Result(2)
Start T3103
Handover Detect(7)
1. 2. 3. 4.
The MS sends BTS1 a measurement report on an SACCH on the Um interface. BTS 1 forwards the measurement report to the BSC. Based on the measurement report, the BSC determines whether to hand over the MS to another cell. If a handover is required, the BSC sends BTS 2 a Channel Activation message. Upon receiving the Channel Activation message, if the channel type is correct, BTS 2 turns on the power amplifier on the specified channel to receive information on the uplink, and sends a Channel Activation Acknowledge message to the BSC. Upon receiving the Channel Activation Acknowledge message, the BSC sends BTS 1 a Handover Command message. Then BTS 1 forwards the command to the MS. The message is sent on an FACCH on the Um interface. BTS 1 starts timer T3103. The Handover Command message has all the information to be transferred on the new channel and the data required for accessing the MS. It also indicates whether the handover is synchronous or asynchronous. Upon receiving the Handover Command message, the MS attempts the access and sends BTS 2 a Handover Access message on the FACCH.
Huawei Technologies Proprietary 14-3
5.
6.
Issue 01 (2007-11-26)
14 Handover
7. 8.
Upon receiving the Handover Access message, BTS 2 sends the BSC a Handover Detect message. Whether a PHY INFO message is sent or not depends on the handover type.
l
Asynchronous handover After the channels of BTS 2 are activated, BTS 2 waits for the access of the MS on a dedicated channel until timer T3103 expires. Upon detecting the Handover Access message from the MS, BTS 2 sends the BSC a Handover Detect message and at the same time to the MS a PHY INFO message on an FACCH. The PHY INFO message carries the new TA calculated by BTS 2. Upon receiving the PHY INFO message, the MS sends BTS 2 an SABM frame.
Synchronous handover BTS2 does not send the PHY INFO message. Upon sending the Handover Access message, the MS sends BTS 2 the SABM frame.
9.
When the PHY INFO message is sent depends on the handover type.
l
Asynchronous handover The MS starts timer T3124 upon sending the Handover Access message for the first time. It stops timer T3124 upon receiving the PHY INFO message, and sends BTS 2 an SABM frame on an FACCH.
Synchronous handover Upon sending the Handover Access message, the MS sends BTS 2 an SABM frame.
10. Upon receiving the first SABM frame, BTS 2 sends an Establishment Indication message to notify the BSC of radio link establishment. 11. At the same time, BTS2 sends a UA frame on an FACCH to notify the MS of radio link establishment. 12. The MS sends BTS 2 a Handover Complete message on the FACCH. BTS 2 forwards the message to notify the BSC of the handover success. The Handover Complete message carries only the handover complete indication. The MS does not return to the old channel after sending this message. If the MS does not receive the PHY INFO message or the UA frame from the target cell, it sends a Handover Failure message on the old channel. 13. Upon receiving the Handover Complete message, the BSC stops timer T3103 and sends a Handover Performed message to notify the MSC of the handover completion. The Handover Performed message carries the handover type. At the same time, the BSC sends an RF Channel Release message to notify BTS 1 of channel release. The target cell forwards to the BSC the Handover Complete message it receives from the MS. Upon receiving the Handover Complete message, the BSC sends an RF Channel Release message to notify BTS 1 of channel release. Upon receiving the RF Channel Release message, BTS 1 sends an RF Channel Release Acknowledge message. The message indicates that the radio channel is released and ready for reallocation.
14-4
Issue 01 (2007-11-26)
14 Handover
Handover Access(9) Start T3124 Handover Detect(11) Handover Access(10) FACCH PHY INFO(13) FACCH Stop T3124 Establish Indication(15) SABM(14) FACCH UA(16) FACCH Handover Complete(19) Handover Complete(18) Handover Complete(17) FACCH
Handover Detect(12)
The inter-BSC handover procedure involves more A-interface signaling procedures than the intra-BSC handover procedure. These signaling procedures are described subsequently. For details about other signaling messages, refer to 14.1.2 Inter-BSC Handover Procedure. 1. When an MS needs to be handed over to a cell controlled by BSC 2, BSC 1 sends the MSC a Handover Required message and starts timer T7. This message carries the CELL IDs of the target cell group and the serving cell, and the handover cause. Upon receiving the Handover Required message, if the MSC finds that the location area of the target cell is under itself, it sends BSC 2 a Handover Request message. The Handover Request message carries the information, transmission mode, MS classmark, and required channel classmark of the serving and the target cells. Upon receiving the Handover Request message, BSC 2 sends the MSC an SCCP Connection Confirm message, indicating that its
Huawei Technologies Proprietary 14-5
2.
Issue 01 (2007-11-26)
14 Handover
connection to the MSC is established. The A interface messages are sent through this SCCP connection. 3. BSC 2 activates a new channel and sends a Handover Request Acknowledge message to notify the MSC that the channel is now available. The Handover Request Acknowledge message carries the information of the allocated handover resources and the handover command indicating that the BSC is ready. Upon receiving the Handover Request Acknowledge message, the MSC sends BSC 1 a Handover Command message. Then BSC 1 stops timer T7. BSC 1 sends the MS a Handover Command message and starts timer T8, requesting the MS to access the new channel. The Handover Command message carries the cell ID, channel type, and handover reference. Upon receiving the Handover Complete message from BSC 2, the MSC sends BSC 1 a Clear Command message. The Clear Command message carries the clearance causes. BSC 1 stops timer T8, initiates a channel release procedure, and sends the MSC a Clear Complete message.
NOTE
4.
5.
If the serving cell and the target cell are in different location areas, the MS initiates a location update procedure after a call is complete.
14-6
Issue 01 (2007-11-26)
14 Handover
Handover Required(2)
Perform Handover(3)
Handover Request(4)
Radio Channel Ack(8) IAM(9) Handover Command(12) FACCH Handover Command(11) ACM(10)
Handover Detect(15)
Handover Detect(14)
Establish Indication(19)
Handover Complete(23)
Handover Complete(22)
For the inter-MSC handover procedure, refer to 14.1.1 Intra-BSC Handover Procedure and 14.1.2 Inter-BSC Handover Procedure. The messages on the E interface are as follows: 1. 2. 3. 4. 5. Perform Handover: MAP layer message. It contains the CGI of the serving cell and the target cell and the required channel type. It informs MSC2 that a handover will be initiated. Radio Channel Acknowledge: MAP layer message. It carries the information of the new channel in the target cell and the handover number. IAM: initial address message. It is a TUP/ISUP message. ACM: address complete message. It is a TUP/ISUP message. Send End Signal: MAP layer message.
14 Handover
Figure 14-4 shows the inter-system handover procedure. Figure 14-4 GSM-to-UMTS handover procedure
MS BSS MSC Handover Required(1) Handover Command(3) FACCH Inter System to UTRAN Handover Command(2) Start T3121 Handover Complete(5) Stop T3121 Clear Command(6) Clear Complete(7) Handover to UTRAN Complete(4) FACCH RNC MS
Handover Complete(9)
The GSM-to-UMTS handover procedure is as follows: 1. 2. 3. 4. The BSS sends a Handover Required message to the MSC. Upon receiving the Handover Required message, the MSC sends the BSS an Inter System To UTRAN Handover Command message and starts timer T3121. Upon receiving the Inter System To UTRAN Handover Command message, the BSS sends the MS a Handover Command message on an FACCH. After the connection is successfully established, the MS sends the RNC a Handover to UTRAN Complete message on a UTRAN channel.
Huawei Technologies Proprietary Issue 01 (2007-11-26)
14-8
14 Handover
5. 6.
The RNC forwards the Handover Complete message to the MSC. Upon receiving the Handover Complete message, the MSC stops timer T3121 and initiates a channel release procedure.
NOTE
For the UMTS-to-GSM handover procedure, refer to the GSM-to-UMTS handover procedure mentioned earlier.
2. 3. 4. 5. 6.
Issue 01 (2007-11-26)
14 Handover
2. 3.
Upon handover initiation, BTS 1 sends the MSC a Handover Required message and starts timer T17 to wait for a Handover Command message. Upon receiving the Handover Ruest message from the MSC, BSC 2 allocates and activates channels according to the target cell ID in the message. After channel activation, BTS 2 sends the MSC a Handover Request Acknowledge message that carries the Handover Command message. BTS 1 forwards to the MS the Handover Command message that BSC 1 receives and at the same time starts timer T8 to wait for the handover completion. If the Clear Command message with the cause value Handover Success is received before T8 expires, BSC 1 considers that the handover is successful. If the MS returns to the old channel before timer T8 expiry, BSC 1 stops timer T8 and sends the MSC a Handover Failure message. If timer T8 expires, BSC 1 considers that the call drops and sends the MSC a Clear Request message. BTS 2 forwards the Handover Detect message to the MSC and continues to wait for the Establishment Indication message and the Handover Complete message. Upon receiving the Handover Complete message, BTS 2 sends a Handover Complete message to notify the MSC of handover completion. Upon receiving the Clear Command message, BTS 1 releases the radio resources the call occupies and returns the MSC a Clear Complete message.
4.
5. 6. 7.
Obtaining the UTRAN neighbor cell information and the UTRAN system parameters from the Idle Mode, Handover Data, and Other Attributes in the Cell Attributes window. Recording the capability of the MS
The internal BSC signaling procedure of the inter-system handover is the same as that described in 14.2.2 Internal BSC Signaling Procedure of the Inter-BSC Handover.
14 Handover
14.3.3 Inter-Cell Handover Failure (MS Returning to the Old Channel) This topic describes the fault, probable causes, and handling suggestions. 14.3.4 BSC Receiving a Connection Failure Indication Message This topic describes the fault, probable causes, and handling suggestions. 14.3.5 Forced Handover Failure This topic describes the fault, probable causes, and handling suggestions. 14.3.6 Handover Failure Caused by CIC Malfunction This topic describes the fault, probable causes, and handling suggestions. 14.3.7 Handover Failure Caused by MS Access Failure This topic describes the fault, probable causes, and handling suggestions.
Description
No channels are available in the target cell.
Analysis
The probable causes are as follows:
l l l
During an inter-cell handover, no TCHs are available in the target cell. During a cross-cell handover, no SDCCHs are available in the target cell. During an intra-cell handover due to bad quality, no TCHs are available in the cell.
Handling Suggestions
The handling suggestions are as follows:
l l
Check whether the target cell is congested. If yes, add TRXs to the target cell. On the Cell Attributes tab page, click Channel Management. In the displayed dialog box, click Advanced. On the Huawei Channel Allocation Algorithm II and Radio Channel Management and Control tab page, check whether TCH Traffic Busy Threshold (%) is set properly. On the Cell Attributes tab page, click Channel Management. In the displayed dialog box, check whether Enhanced TCH Adjust Allowed is set properly.
Description
The old BSS does not receive a Clear Command message from the MSC or a Handover Failure message from the MS upon T8 expiry.
Issue 01 (2007-11-26) Huawei Technologies Proprietary 14-11
14 Handover
Analysis
If the old BSS does not receive a Clear Command message from the MSC or a Handover Failure message from the MS upon T8 expiry, it will release the dedicated channels and send the MSC a Clear Request message with the cause value Radio Interface Message Failure. Before a Clear Command message is received, the terrestrial resources on the old BSS side remain allocated. On receiving the Clear Command message, the old BSS changes the state of the terrestrial resources to idle and sends a Clear Complete message to the MSC. Then the MSC releases the SCCP connection to the old BSS and thus terminates the connection with the BSS.
Handling Suggestions
On the Cell Attributes tab page, click Other Attributes. Then click Advanced. On the Cell Timer tab page, check whether T8 is set properly.
Fault
The MS returns to the old channel after inter-cell handover failure.
Probable Causes
The probable causes are that the MS cannot access the old channel due to bad transmission quality on the Um interface, low level, or incorrect data configuration of the external cells.
Handling Suggestions
Check the transmission quality on the Um interface.
Fault
Calls drop.
Probable Causes
The probable causes are as follows:
l l
Handling Suggestions
l l
Check the resources on the Um interface. Check the antenna system and the power amplifier.
Huawei Technologies Proprietary Issue 01 (2007-11-26)
14-12
14 Handover
Fault
Forced handover fails.
Probable Causes
l l l l
No neighbor cell Incorrect configuration of the neighbor cell No resources in the neighbor cell Bad radio conditions in the neighbor cell
Handling Suggestions
Check the data configuration and the radio conditions of the neighbor cell, for example, the level.
Fault
Handover fails. The cause value of the Handover Failure message is Requested Terrestrial Resource Unavailable.
Probable Causes
If the CIC allocated in the Handover Request message received by the target BSC is marked as BLOCK, the target BSC will respond to the MSC with a Handover Failure message with the cause value Requested Terrestrial Resource Unavailable.
Handling Suggestions
Check the state of the CIC.
Fault
The MS cannot be handed over.
Probable Causes
Refer to the handling suggestions.
Issue 01 (2007-11-26) Huawei Technologies Proprietary 14-13
14 Handover
Handling Suggestions
l l l l
Check whether the handover trigger conditions are met. Check whether there is a neighbor cell list in the measurement report. Check whether the neighbor cell has available channels. Check whether the data of the neighbor cell is incorrect, for example, whether there is inconsistency in CGI.
14-14
Issue 01 (2007-11-26)